WCDMA Call Drop Problem Analysis
Short Description
Huawei WCDMA Call Drop Problem Analysis...
Description
Internal
WCDMA Call Drop Problem Analysis
www.huawei.com
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Foreword: Causes of Call Drop in GSM & UMTS GSM
UMTS
Neighbor cell problem
No response after T3103 expiry
Interference problem
Interference problem
Coverage problem
Coverage problem
Handoff problem
Improper parameter setting
Interactive process
Equipment problem
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 2
Objectives
Upon completion of this course, you will be able to understand:
Definition of the call drop
Process for handling the call drop problem
Various methods to analyze call drop data
Solutions to call drop problems
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 3
Contents 1. Definition and classification 2. Causes and handling process
3. Solutions
4. Case analysis
5. Concerns in various network optimization phases Training.huawei.com
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 4
1 Definition and Classification
HUAWEI TECHNOLOGIES CO., LTD.
1.1 Normal release procedure
1.2 Call drop over the Um interface
1.3 Call drop measurement - CS
1.4 Call drop measurement - PS
HUAWEI Confidential
Page 5
Normal Release Procedure
Procedure of CS service normal release
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 6
Normal Release Procedure
CS Normal Release Procedure 1. The UE sends the RRC_UL_DIR_TRANSF message to the RNC. If the nas message carried in this message is 0325, it indicates that the message is the disconnect message of the call control sublayer. 2. The RNC sends the RANAP_DIRECT_TRANSFER message to the CN. If the nas pdu carried in this message is 0325, it indicates that the message is the disconnect message of the call control sublayer. 3. The CN sends the RANAP_DIRECT_TRANSFER message to the RNC. If the nas pdu carried in this message is 832d, it indicates that the message is the release message of the call control sublayer. 4. The RNC sends the RRC_DL_DIRECT_TRANSF message to the UE. If the nas message carried in this message is 832d, it indicates that the message is the release message of the call control sublayer. 5. The UE sends the RRC_UL_DIR_TRANSF message to the RNC. If the nas message carried in this message is 032a, it indicates that the message is the release complete message of the call control sublayer. 6. The RNC sends the RANAP_DIRECT_TRANSFER message to the RNC. If the nas pdu carried in this message is 032a, it indicates that the message is the release complete message of the call control sublayer.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 7
Normal Release Procedure 7. The CN sends the RANAP_IU_RELEASE_COMMAND message to the RNC to release resources of the Iu interface, including resources of the RANAP layer and the ALCAP layer. 8. The RNC sends the RANAP_IU_RELEASE_COMPLETE message to the CN. 9. The RNC sends the RRC_RRC_CONN_REL message to the UE to release the RRC connection. 10. The UE sends the RRC_RRC_CONN_REL_CMP message to the RNC. 11. The RNC sends the NBAP_RL_DEL_REQ message to the NodeB to release resources of the Iu interface, including resources of the NBAP layer and the ALCAP layer. 12. The NodeB sends the NBAP_RL_DEL_RSP message to the RNC. Then, the release procedure is complete.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 8
Normal Release Procedure
Procedure of PS service normal release
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 9
Normal Release Procedure
Procedure of PS service normal release 1. The UE sends the RRC_UL_DIR_TRANSF message to the RNC. The nas message carried in the message is 0a46, indicating that the message is the deactivate PDP context request message of the session management sublayer. 2. The RNC sends the RANAP_DIRECT_TRANSFER message to the CN. The nas pdu carried in the message is 0a46, indicating that the message is the deactivate PDP context request message of the session management sublayer. 3. The CN sends the RANAP_DIRECT_TRANSFER message to the RNC. The nas pdu carried in the message is 8a47, indicating that the message is the deactivate PDP context accept message of the session management sublayer. 4. The CN sends the RNC the RANAP_RAB_ASSIGNMENT_REQ message carrying the RAB list (to be released) with RAB IDs to be released. 5. The RNC sends the RRC_DL_DIRECT_TRANSF message to the UE. The nas message carried in the message is 8a47, indicating that the message is the deactivate PDP context accept message of the session management sublayer. 6. The RNC sends the NBAP_RL_RECFG_PREP message to the NodeB.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 10
Normal Release Procedure 7. The NodeB sends the NBAP_RL_RECFG_READY message to the RNC. 8. The RNC sends the RRC_RB_REL message to the UE to release the radio bearer of the service. 9. The NodeB sends the NBAP_RL_RECFG_COMMIT message to the RNC. 10. The UE sends the RRC_RB_REL_CMP message to notify the RNC that the radio bearer of the service is released. 11. The RNC sends the RANAP_RAB_ASSIGNMENT_RESP message to notify the CN that the radio access bearer is released.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 11
1 Definition and Classification
HUAWEI TECHNOLOGIES CO., LTD.
1.1 Normal release procedure
1.2 Call drop over the Um interface
1.3 Call drop measurement - CS
1.4 Call drop measurement - PS
HUAWEI Confidential
Page 12
Call Drop over the Um Interface Definition of call drop over the Um interface
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 13
Call Drop over the Um Interface
Call drop defined by field tests
According to the Um interface signaling recorded on the UE side, if messages of the Um interface meet one of the following conditions during the conversation (in the connection state), you can infer that a call is dropped. (1) The RRC Release message is not received. The UE changes from the CELL_DCH state to the IDLE state. (2) The RRC Release message is received in which the release cause value is not Normal. (3) The CC Disconnect message, CC Release Complete message, or CC Release message is received in which the release cause value is not Normal Clearing, Normal Unspecified, user busy, user alerting no answer, call rejected or destination out of order.
Call drop defined by traffic statistics
According to the signaling recorded by the RNC, if the RNC sends the Iu Release Request or the RAB Release Request to the CN over the Iu interface, you can infer that a call is dropped (excluding certain special causes).
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 14
1 Definition and Classification
HUAWEI TECHNOLOGIES CO., LTD.
1.1 Normal release procedure
1.2 Call drop over the Um interface
1.3 Call drop measurement - CS
1.4 Call drop measurement - PS
HUAWEI Confidential
Page 15
Definition of Measurement Summary of measurement classification Call drop defined by the measurement CS call drop Object-oriented statistics: RNC, cell Service-oriented statistics: AMR, VP service
PS call drop Object-oriented statistics: RNC, cell Service-oriented statistics: PS service, HSDPA, HSUPA
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 16
Call Drop Measurement - CS CS
Service Drop Ratio
KPI Name
CS Service Drop Ratio
Measurement Scope
Cell
Formula
Notes
CS _ CDR =
CSRABAbnor mal Re lease × 100% CSRAB Re lease
The RNC level KPIs can be calculated by aggregating all the cell counters and Iur counters.
CSRABAbnormalRelease (cell)
VS.RAB.Loss.CS.Abnorm+ VS.RAB.Loss.CS.RF
VS.RAB.Loss.CS.Abnorm: Numbers of abnormally released RABs except RF causes in a cell VS.RAB.Loss.CS.RF: Number of Released RABs Triggered by RNC due to RF Reason
CSRABRelease (cell)
VS.RAB.Loss.CS.RF + VS.RAB.Loss.CS.Abnorm + VS.RAB.Loss.CS.Norm
VS.RAB.Loss.CS.Norm: Numbers of Released RABs Triggered by RNC due to CS Normal Cause in a cell
This measurement helps evaluate the call drop rate of CS services in a RNC or cluster. This counter is measured when the RNC initiates the abnormal release procedure through the RAB RELEASE REQUEST and IU RELEASE REQUEST messages. HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 17
Call Drop Measurement - CS
AMR Call Drop Ratio KPI Name
AMR Call Drop Ratio
Measurement Scope
Cell
Formula
Notes
AMR _ CDR =
AMRRABAbno rmal Re lease × 100% AMRRAB Re lease
The RNC level KPIs can be calculated by aggregating all the cell counters and Iur counters.
AMRRABAbnromalRelease (cell)
VS.RAB.Loss.CS.AMR
Number of released CS AMR service RABs triggered by RNC in a cell
AMRRABRelease
VS.RAB.Loss.CS.AMR + VS.RAB.Loss.CS.Norm.AMR
VS.RAB.Loss.CS.Norm.AMR: Numbers of Released RABs Triggered by RNC due to CS Normal Cause in a cell(AMR)
This measurement helps evaluate the call drop rate of AMR services in a RNC or cluster. This counter is measured when the RNC initiates the abnormal release procedure through the RAB RELEASE REQUEST and IU RELEASE REQUEST messages.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 18
Call Drop Measurement - CS
VP Call Drop Ratio KPI Name
VP Call Drop Ratio
Measurement Scope
Cell
Formula
Notes
VP _ CDR =
VPRABAbnor mal Re lease × 100% VPRAB Re lease
The RNC level KPIs can be calculated by aggregating all the cell counters and Iur counters.
VPRABAbnormalRelease (cell)
VS.RAB.Loss.CS.Conv64K
Number of released CS 64 k service RABs triggered by RNC in a cell
VPRABRelease (cell)
VS.Norm.Rel.CS.Conv.RB.64 + VS.RAB.Loss.CS.Conv64K
Numbers of VP Service RABs released
This measurement helps evaluate the call drop rate of VP services in a RNC or cluster. This counter is measured when the RNC initiates the abnormal release procedure through the RAB RELEASE REQUEST and IU RELEASE REQUEST messages.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 19
1 Definition and Classification
HUAWEI TECHNOLOGIES CO., LTD.
1.1 Normal release procedure
1.2 Call drop over the Um interface
1.3 Call drop measurement - CS
1.4 Call drop measurement - PS
HUAWEI Confidential
Page 20
Call Drop Measurement - PS
PS Service Drop Ratio
KPI Name
PS Service Drop Ratio
Measurement Scope
Cell
Formula
PS _ CDR =
Notes
The RNC level KPIs can be calculated by aggregating all the cell counters and Iur counters.
PSRABAbnormalRelease (cell)
PSRABAbnormal Re lease ×100% PSRAB Re lease
VS.RAB.Loss.PS.RF + VS.RAB.Loss.PS.Abnorm
VS.RAB.Loss.PS.RF: Numbers of abnormally released RABs except RF causes in a cell VS.RAB.Loss.PS.Abnorm: Number of released RABs triggered by RNC due to RF reason
PSRABRelease (cell)
VS.RAB.Loss.PS.RF + VS.RAB.Loss.PS.Abnorm + VS.RAB.Loss.PS.Norm
VS.RAB.Loss.PS.Norm: Numbers of released RABs triggered by RNC due to PS normal causes in a cell
This measurement helps evaluate the call drop rate of PS services in a RNC or cluster. This counter is measured when the RNC initiates the abnormal release procedure through the RAB RELEASE REQUEST and IU RELEASE REQUEST messages. Note: The cell level counter calculates only the RAB releases on the SRNC, whereas the result of the above formula includes the R99 call drop and HSPA call drop.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 21
Call Drop Measurement - PS
HSDPA Service Drop Ratio KPI Name
HSDPA Service Drop Ratio
Measurement Scope
Cell
Formula
Notes
HSDPA _ CDR =
HSDPA _ RBAbnormal Re lease × 100% HSDPA _ RB Re lease
1. The RNC level KPIs can be calculated by aggregating all the cell counters. 2. The normal transition from HS-DSCH to FACH/DCH is considered as normal HS-DSCH release ( including transitions due to mobility).
This measurement helps evaluate the call drop rate of PS services carried by the HSDPA in a RNC or cluster. This counter is measured when the RNC initiates the abnormal release procedure through the RAB RELEASE REQUEST and IU RELEASE REQUEST messages.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 22
Call Drop Measurement - PS
HSDPA Service Drop Ratio HSDPA_RBAbnormalRele ase
VS.HSDPA.RAB.Loss.Abnorm.No nRF + VS.HSDPA.RAB.Loss.RF
VS.HSDPA.RAB.Loss.Abnorm.NonRF: Number of released PS service RABs carried by HSDPA triggered by RNC in a cell. The cause is not RF. VS.HSDPA.RAB.Loss.RF: Number of released PS service RABs carried by HSDPA triggered by RNC in a cell. The cause is RF.
HSDPA_RBNormalRelease
VS.HSDPA.RAB.Loss.Norm + VS.HSDPA.RAB.Loss.InActivity + VS.HSDPA.ChR.HSDSCHtoDCH + VS.HSDPA.ChR.HSDSCHtoFAC H+ VS.HSDPA.HHO.H2D.SuccOutInt raFreq + VS.HSDPA.HHO.H2D.SuccOutInt erFreq
VS.HSDPA.RAB.Loss.Norm: Number of released PS service RABs carried by HSDPA triggered. The cause is normal. VS.HSDPA.RAB.Loss.InActivity: Number of released PS service RABs carried by HSDPA triggered. The cause is User Inactivity. VS.HSDPA.ChR.HSDSCHtoDCH: Number of successful channel handovers from the HS-DSCH to the DCH in the same cell VS.HSDPA.ChR.HSDSCHtoFACH: Number of successful channel handovers from the HS-DSCH to the FACH in the same cell VS.HSDPA.HHO.H2D.SuccOutIntraFreq: Number of successful intra-frequency hard handovers from the HS-DSCH to the DCH between two cells VS.HSDPA.HHO.H2D.SuccOutInterFreq: Number of successful inter-frequency hard handovers from the HS-DSCH to the DCH between two cells
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 23
Call Drop Measurement - PS
HSUPA Service Drop Ratio KPI Name
HSUPA Service Drop Ratio
Measurement Scope
Cell
Formula
HSUPA _ CDR =
Notes
1. The RNC level KPIs can be calculated by aggregating all the cell counters. 2. The normal transition from E-DCH to FACH/DCH is considered as normal E-DCH release ( including transitions due to mobility).
HSUPA _ RBAbnormal Re lease × 100% HSUPA _ RB Re lease
This measurement helps evaluate the call drop rate of PS services carried by the HSUPA in a RNC or cluster. This counter is measured when the RNC initiates the abnormal release procedure through the RAB RELEASE REQUEST and IU RELEASE REQUEST messages.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 24
Call Drop Measurement - PS
HSUPA Service Drop Ratio HSUPA_RBAbnormalReleasego back
VS.HSUPA.RAB.Loss.Abnorm
VS.HSUPA.RAB.Loss.Abnorm: Number of abnormal released PS service RABs carried by HSUPA triggered by RNC in a cell
HSUPA_RBNormalRelease
VS.HSUPA.RAB.Loss.Norm + VS.HSUPA.ChR.IntraCell.EDCHtoDCH.Succ + VS.HSUPA.ChR.IntraFreq.EDCHtoDCH.Succ + VS.HSUPA.ChR.InterFreq.EDCHtoDCH.Succ + VS.HSUPA.ChR.EDCHtoFACH.Succ
VS.HSUPA.RAB.Loss.Norm: Number of released PS service RABs carried by HSUPA triggered. The cause is normal. VS.HSUPA.ChR.IntraCell.EDCHtoDCH.Succ: Number of successful attempts to switch the channel type from EDCH to DCH in the same cell of the RNC VS.HSUPA.ChR.IntraFreq.EDCHtoDCH.Succ: Number of successful attempts to switch the channel type from EDCH to DCH due to intrafrequency hard handover between two cells. VS.HSUPA.ChR.InterFreq.EDCHtoDCH.Succ: Number of successful attempts to switch the channel type from EDCH to DCH due to interfrequency hard handover between two cells. VS.HSUPA.ChR.EDCHtoFACH.Succ: Number of successful attempts to switch the channel type from EDCH to FACH in the same cell of the RNC
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 25
Contents 1. Definition and classification
2. Causes and handling process
3. Solutions
4. Case analysis
5. Concerns in various network optimization phases Training.huawei.com
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 26
2 Causes and Handling Process
HUAWEI TECHNOLOGIES CO., LTD.
2.1 Common reasons for call drop
2.2 Drive test data analysis procedure
2.3 Measurement data analysis procedure
2.4 Signaling tracing data analysis procedure
2.5 User complaint data analysis procedure
HUAWEI Confidential
Page 27
Common Reasons for Call Drop
Neighbor Cell Missing Generally, the call drop is caused by neighbor cell missing during the early phase of optimization. For the intra-frequency neighbor cells, you can use the following methods to determine whether the call drop is caused by intra-frequency neighbor cell missing. Method 1: Check the EcIo information about cells in the active set recorded by the UE and the Best Server EcIo information recorded by the Scanner. If the EcIo recorded by the UE is poor and the Best Server EcIo recorded by the Scanner is good, check whether the Best Server scrambling code recorded by the Scanner is included in the intra-frequency measurement control. If the scrambling code is not included, you can infer that the call drop is caused by the neighbor cell missing. Method 2: If the UE reconnects to the network immediately after the call drop and the cell scrambling code used during the reconnection of the UE is inconsistent with that used during the call drop, the call drop may be caused by the neighbor cell missing. You can confirm the cause through the measurement control. The neighbor cell missing, including the inter-frequency neighbor cell missing and the inter-RAT neighbor cell missing can result in call drop. Method 3: Adopt the Nastar neighbor cell analysis function to check whether the neighbor cell missing problem exists. Method 4: Enable the measurement analysis detection set (RNC detection set) to report 1A event.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 28
Common Reasons for Call Drop
Coverage Problem Generally, poor coverage implies that both the RSCP and EcIo are poor. You can confirm the coverage problem by checking the transmit power of uplink/downlink special channels through the following methods: If the uplink transmit power reaches the maximum value before the call drop and the uplink BLER is poor or the single user tracing recorded by the RNC suggests that Node B reports RL failure, you may infer that the call drop is caused by poor uplink coverage. If the downlink transmit power reaches the maximum value before the call drop and the downlink BLER is poor, you may infer that the call drop is caused by poor downlink coverage. You can also confirm the coverage problem through the following simple and direct method: Check the data collected by the Scanner. If both the RSCP and EcNo of the best cell are poor, you can determine that the poor coverage results in the call drop.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 29
Common Reasons for Call Drop
Handoff Problem There are two reasons for the call drop caused by the soft handoff/inter-frequency, that is, it is too late to perform the handoff or ping-pong handoff. In terms of the signaling process, for the CS service, the UE does not receive the active set update command; for the PS service, the TRB is reset before the handoff of the UE. In terms of signal, there are two scenarios in which it is too late for the handoff: (1) Corner: The EcIo of the source cell has a sudden sharp drop, and the EcNo of the target cell has an unexpected dramatic increase. (2) Pinpoint: The EcIo of the source cell increases after a period of time in rapid fall. The EcIo of the target cell has a sudden increase in a short time period. The ping-pong handoff involves the following cases: (1) The primary cell changes rapidly: Two or more cells take turns to be the primary cell. The primary cell has better RSCP and EcIo and exists in a short period of time. (2) There are multiple secondary cells: The RSCP is normal, and there is slight difference between RSCPs of cells. The EcIo in each cell is poor.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 30
Common Reasons for Call Drop
Interference Problem For the downlink, if the CPICH RSCP is greater than -85 dB and the EcIo is smaller than 13 dB, the call drop tends to occur. This may be caused by downlink interference. For the uplink, if the RTWP is 10 dB greater than the normal value (-104 to -105), there may be a call drop. This is caused by pilot pollution.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 31
Common Reasons for Call Drop
Interaction Process Problem Processes, such as AMR control, enabling or disabling the DCCC, compression mode, and UE state transition may fail due to reasons relating to the signal, UE capability, or the interaction between the equipment in the RAN and UE, which finally results in call drop. There is no common method to solve these problems. The method varies depending on the specific process or UE.
Other Abnormal Problems If the preceding causes are excluded, the call drop may be caused by equipment problems. You need to perform further cause analysis by checking logs and alarms of the equipment. For example: The synchronization failure causes repeated addition or deletion of links. The UE does not report the la measurement report, which results in the call drop.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 32
2 Causes and Handling Process
HUAWEI TECHNOLOGIES CO., LTD.
2.1 Common reasons for call drop
2.2 Drive test data analysis procedure
2.3 Measurement data analysis procedure
2.4 Signaling tracing data analysis procedure
2.5 User complaint data analysis procedure
HUAWEI Confidential
Page 33
Drive Test Data Analysis Procedure Drive Test Data Analysis Procedure
1. Prepare data.
2. Obtain call drop location and time
3. Analyze signal changes of the primary cell of the Scanner
Frequently changed
Are signals of the primary cell stable? stable 4 RSCP and EcIO of the best cell of the Scanner
4.1 Both the RSCP and the EcIo are poor.
4.2 The RSCP is normal, and the EcIo is poor.
4.3 Both the RSCP and the EcIo are normal. Inconsistent
Compare the best cell of the UE and that of the Scanner Consistent
Check whether the call drop is caused by the neighbor cell missing.
N
Y
Coverage problem
Neighbor cell missing
4. Perform the drive test again.
HUAWEI TECHNOLOGIES CO., LTD.
Uplink interference or not
N
Y Untimely handoff
Uplink interference problem
Abnormal call drop
Is the problem solved?
HUAWEI Confidential
Page 34
Pilot frequency interference problem
Ping-pong handoff problem
Drive Test Data Analysis Procedure 1. Prepare the following data:
Data files collected by the drive test software Single user tracing data recorded by the RNC CDL recorded by the RNC 2. Obtain the call drop location. Adopt the drive test software, such as the Analyzer to obtain the call drop time and location, pilot frequency data collected by the Scanner before and after the call drop, information about the active set and monitored set collected by the UE, and signaling process. 3. Analyze changes of the primary cell of the Scanner. If the primary cell is relatively stable, perform further analysis on the RSCP and EcIo. If the primary cell changes frequently, analyze causes. If there is no primary cell, perform the cause analysis on the call drop occurring during the ping-pong handoff.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 35
Drive Test Data Analysis Procedure 4. Analyze the RSCP and EcIo of the primary cell of the Scanner. Check the RSCP and EcNo of the best cell of the Scanner and take appropriate measures accordingly. 4.1 If both the RSCP and EcNo are poor, the coverage problem leads to the call drop. 4.2 If the RSCP is normal, and the EcNo is poor, the call drop is caused by the pilot frequency interference problem rather than untimely handoff and inter-frequency neighbor cell. 4.3 If both the RSCP and the EcNo are normal and the cell of the active set of the UE are inconsistent with the best cell of the Scanner, the call drop may be caused by the neighbor cell missing or untimely handoff. If the cell of the active set of the UE is consistent with the best cell of the Scanner, the uplink interference may result in call drop or an abnormal call drop occurs. 5. Carry out the drive test repeatedly. A drive test may not collect all the information required by call drop location. Therefore, you need to carry out the drive test for several times to collect data and check whether the call drop location is random or fixed. Generally, take related measures to eliminate call drops occurring on the fixed location and check whether to eliminate call drops occurring on random locations based on the occurrence probability.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 36
2 Causes and Handling Process
HUAWEI TECHNOLOGIES CO., LTD.
2.1 Common reasons for call Drop
2.2 Drive test data analysis procedure
2.3 Measurement data analysis procedure
2.4 Signaling tracing data analysis procedure
2.5 User complaint data analysis procedure
HUAWEI Confidential
Page 37
Measurement Data Analysis Procedure Measurement Data Analysis Procedure 1. Analyze the call drop rate of the RNC.
2. Analyze the call drop rate index of the cell.
Y
3. Check whether the equipment in the cell is normal.
3.1 Solve the equipment problem.
N 4. Analyze call drop reasons.
4.1The signaling RB reset or service RB reset causes the call drop.
Y Solve the coverage problem.
N 4.2 Check whether the call drop is caused by the handoff?
Y Solve the call drop problem arising from the handoff.
N 4.3 Check whether the call drop is caused by the interference?
Y Solve the interference problem.
N 5. Carry out the drive test to find out the call drop reasons.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 38
Measurement Data Analysis Procedure
1. Analyze call drop rate indexes of the RNC. Check whether the call drop rate index is normal based on the overall call drop rate index of the RNC. 2. Analyze call drop rate indexes of the cells such as AMR call drop rate, VP call drop rate, PS call drop rate, hard handoff call drop rate, inter-RAT handoff call drop rate and sort all of these cells according to the indexes. Analyze causes of call drops occurring in the cells with worse or worst indexes. 3. Check whether the cell is normal. Check alarms relating to cells and exclude causes of abnormal cells.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 39
Measurement Data Analysis Procedure
4. Analyze call drop causes. If the call drop is not caused by aa12 abnormality of the Iu interface or the GTPU abnormality, check whether the reset of signaling RLC or service RLC is the call drop cause. Analyze related handoff indexes (incoming handoff success rate and outgoing handoff success rate) related to the cell to check whether the call drop is caused by the handoff failure. Analyze the measurement relating to the overall bandwidth receiving power to check whether related uplink interference indexes are high during the period of the high call drop rate. Then, you can determine whether the call drop is caused by uplink interference. 5. Carry out the drive test to make call drop problems reoccur. If the call drop problem persists after the analysis of measurement data, carry out drive tests in the cell to trace the signaling process on the UE side and the RNC. For detailed analysis method, see the drive test analysis procedure.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 40
2 Causes and Handling Process
HUAWEI TECHNOLOGIES CO., LTD.
2.1 Common reasons for call drop
2.2 Drive test data analysis procedure
2.3 Measurement data analysis procedure
2.4 Signaling tracing data analysis procedure
2.5 User complaint data analysis procedure
HUAWEI Confidential
Page 41
Signaling Tracing Data Analysis Procedure Signaling tracing data analysis procedure 1. Obtain the single user tracing message
2. Obtain information about the call drop location.
3.1 Solve call drop problems arising on the signaling plane.
3. Check whether the call drop occurs on the signaling plane.
4.1 Solve call drop problems arising on the user plane.
4 . Check whether the call drop occurs on the user plane.
Y 5. Check whether abnormal call drop occurs. N
5.1 Solve abnormal call drop problems.
Check whether call drop problems are solved.
6. Carry out drive tests to make call drop problems reoccur
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 42
Signaling Tracing Data Analysis Procedure 1. Obtain single user tracing messages. Trace the single user on the RNC or M2000 before recording related single user tracing messages. Generally, the messages recorded during the IMSI-based tracing is sufficient for the analysis of the call drop problems.
2. Obtain information about the call drop location. Single user tracing messages suggest that the cause of a call drop on the user plane is that the RNC actively sends the RANAP_RAB_RELEASE_REQ message to release the RAB and the cause of a call drop on the signaling plane is that the RNC actively sends the RANAP_IU_RELEASE_REQ message to release the Iu interface. By checking the two messages, you can obtain the call drop time and signaling messages before the call drop and perform further analysis.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 43
Signaling Tracing Data Analysis Procedure 3. Analyze the call drop on the signaling plane. If a call drop occurs on the signaling plane, the UE or the RNC cannot receive the confirmation message, which leads to the SRB reset and connection release. The SRN reset can be caused by uplink messages such as the measurement control message, active set update message, physical channel reconfiguration message, transmission channel reconfiguration message, RB reconfiguration message, and command for the handoff from 3G networks to 2G networks. You need to check messages traced on the UE side to determine whether the UE receives these commands. The SRN reset can also be caused by downlink messages such as the measure report, active set update completion message, physical channel reconfiguration completion message, transmission channel reconfiguration completion message, and RB reconfiguration completion message. You need to check messages traced on the RNC side to determine whether these tracing messages are received.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 44
Signaling Tracing Data Analysis Procedure 4. Analyze the call drop on the user plane. If the call drop occurs on the user plane, the TRB resets. The TRB resetting occurs during a PS call rather than a Voice or VP call. If there is only one link in the active set, the RL failure may cause the RNC to initiate the Iu release procedure. The lost synchronization of the uplink causes the RL failure. The lost synchronization of the downlink causes the UE to shut down the transmitter, which results in lost synchronization of the uplink. To check whether the lost synchronization of the uplink or lost synchronization of the downlink causes the release process, you need to analyze the transmit power of the UE and the monitored code transmit power of the downlink before the call drop. Poor downlink coverage, strong downlink interference, or uplink interference may lead to TRB reset. If the number of retransmission times of data services is set improperly, the TRB reset occurs before the SRB reset when it is too late for handoff. You must take this case into account.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 45
Signaling Tracing Data Analysis Procedure 5. Analyze abnormal call drops. The abnormal call drop is caused by abnormalities occurs on the equipment or the UE (for example, the transmission is interrupted, the base station equipment is abnormal, and the UE crashes abruptly) rather than the coverage problem, interference problem, or causes of the call drop occurs on the user plane or the signaling plane. If the call drop is caused by the abrupt transmission interruption, you can analyze the CDL or alarms to locate the cause of the call drop; if the call drop is caused by the abnormalities of the base station equipment, you can check the status of the base station; if the call drop is caused by abnormalities of the UE, you can analyze the data recorded by the UE.
6. Carry out drive tests to make the call drop problem reoccur. If the existing data is not sufficient to locate the call drop problem, trace more detailed data. The best way is to carry out drive tests on the call drop location and perform further analysis.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 46
2 Causes and Handling Process
HUAWEI TECHNOLOGIES CO., LTD.
2.1 Common reasons for call drop
2.2 Drive test data analysis procedure
2.3 Measurement data analysis procedure
2.4 Signaling tracing data analysis procedure
2.5 User complaint data analysis procedure
HUAWEI Confidential
Page 47
User Complaint Data Analysis Procedure 1. Understand user complaint. When a user complaint is received, record when and where the problem occurs and describe the problem in detail.
2. Check the measurement. Analyze the related measurement to determine whether the complaint is a specific problem of the user or a general network problem. For a general network problem, perform further analysis on the complaint by referring to the analysis on the measurement.
3. Check alarms. According to the complaint time, check the CN, RNC or check whether the alarm of the base station on the location where the problem occurs can result in call drop. If such alarm exists, clear the alarm.
4. Check the CDL. The CDL records the signaling used by the user or the user status when the abnormality occurs. By analyzing the CDL, you can learn about the details about the complaints.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 48
User Complaint Data Analysis Procedure 5. Perform the dialing test on the complained location to make the problem reoccur. If the problem persists after you analyze the related measurement, alarm, and CDL, perform the dialing test to solve the problem. Record the data generated during the dialing test by using the same method for recording the data generated in the drive test. If it is inconvenient to record the information on the UE side in certain scenarios, use the RNC to record various information, in particular, record and collect the reported information about the EcIo and RSCP to solve the call drop problem caused by the poor coverage. In the case of special locations where it is impossible to perform the dialing test, obtain the IMSI according to the mobile phone number and trace the call on the RNC to locate causes of the call drop.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 49
Contents 1. Definition and classification
2. Causes and handling process
3. Solutions
4. Case analysis
5. Concerns in various network optimization phases Training.huawei.com
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 50
3 Solutions
3.1 Engineering parameter adjustment
HUAWEI TECHNOLOGIES CO., LTD.
3.2 Cell parameter adjustment
HUAWEI Confidential
Page 51
Engineering Parameter Adjustment The engineering parameter adjustments are limited. Basically, you can adjust the height, down tilt, lobe width, gain, and deflection angle of the antenna.
1. For the call drop caused by the uplink or downlink coverage problem Adjust the height and the down tilt of the antenna or replace with the antenna providing more gain or increase the TMA.
2. For the pinpoint or corner effect An effective way is to adjust the antenna. The pinpoint or corner effect occurs on the corner of the street or the junction of the two streets. In this case, you can make a certain angel between the antenna and the street by adjusting the deflection angle. Note that this action should not greatly affect the signal coverage of nearby shops on the street.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 52
Adjustment of Engineering Parameters 3. For the coverage problem caused by the pilot frequency You can adjust engineering parameters of a certain antenna to make the interfered location a primary cell. You can also adjust engineering parameters of other antennas to weaken signals of these cells to decrease the number of pilot frequencies. If permitted, use two base stations to cover the area. If the interference is from two sectors of a base station, incorporate the two sectors. You must consider the adjustment effect of the entire cell when adjusting engineering parameters. Ensure that the measures taken to solve the problem does not bring about new problems in other areas.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 53
3 Solutions
3.1 Engineering parameter adjustment
HUAWEI TECHNOLOGIES CO., LTD.
3.2 Cell parameter adjustment
HUAWEI Confidential
Page 54
Cell Parameter Adjustment 1. Cell individual offset (CIO) The sum of the CIO and the actual measured value is used to determine whether the intra-frequency handoff is to be performed in the event evaluation process of the UE. In addition, the sum can serve as the mobile cell boundary. If the value is larger, the soft handoff is easier and more UEs are in the soft handoff state. In this case, the forward resources are occupied. If the value is smaller, the soft handoff is more difficult and the quality of received signals may be affected. For the pinpoint or corner effect, the better method is to configure the CIO as about 5 dB.
2. Time to trigger the delay related to the soft handoff The delay triggering time refers to the time to trigger 1A, 1B, 1C, or 1D event. The triggering time may affect the promptness of the handoff. Generally, the default triggering time can meet requirements of most scenarios. Set handoff-related parameters according to the environment and adjust the configuration of related parameter for each cell. You can limit the impact of the parameter modifications to certain cells, which reduces the impact on the system.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 55
Cell Parameter Adjustment 3. FilterCoef The layer 3 filter tries to filter out the random impingement samples to enable the filtered measured values to reflect the main change trend of actual measured values. The measured values input in the layer 3 filter are filtered by the layer 1 filter. Therefore, the impacts of fast fading are removed, and the layer 3 filter performs the smooth filtering on shadow fading and few fast fading burrs to provide higher quality measurement data. The filter with greater filtering coefficient has stronger ability to smooth burrs but weaker ability to trace signals. Typical values are set as follows: a. If signals in the handoff area change slowly, the intra-frequency filtering coefficient is set to 7. b. If signals in the handoff area change at a moderate speed, the intra-frequency filtering coefficient is set to 6. c. If signals in the handoff area change rapidly, the intra-frequency filtering coefficient is set to 3.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 56
Cell Parameter Adjustment 4. Threshold for enabling or disabling the compression mode The compression mode is enabled before the inter-frequency or inter-RBT handoff. You can use the compression mode to check the quality of inter-frequency or interRBT cells. The compression mode is enabled only when the RSCP or EcIo of the CPICH meet requirements. In actual applications, the common triggering condition is that the RSCP must meet requirements. Generally, the compression mode requires to measure the quality of the target cell (inter-frequency or inter-RAT cell) to obtain related information. Movements of the UE deteriorate the quality of the current cell. Therefore, the requirement for setting the threshold for enabling the compression mode is to measure that the target cell completes the handoff before the quality deterioration of the current cell leads to the call drop; the requirement for setting the threshold for disabling the compression mode is to avoid the compression mode being enabled or disabled frequently.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 57
Cell Parameter Adjustment 5. RLMaxDLPwr (Maximum Downlink Transmit Power of Radio Links) The high transmit power of special links is favorable for solving call drop problems caused by the poor coverage but causing the interference problem. In this case, the single user consumes high power at the edge of the cell, which impacts on other users and reduces the downlink capacity of the system. Generally, the downlink transmit power is determined by the link budget with a variation of 1-2dB. If the drive test is carried out for once, it is difficult to measure the impact of the high power on the call drop. The measurement, however, reveals the impacts. If the poor coverage causes a higher call drop rate in certain cells, you can raise the maximum transmit power of special links. If the overload results in a higher access failure rate, you can consider to reduce the maximum transmit power.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 58
Cell Parameter Adjustment 6. Number of signaling/service retransmission times If the number of retransmission times of the signaling over links with higher block error rate reaches the maximum value, the signaling is reset, which causes the call drop. If the number of retransmission times of the service transmitted in AM mode reaches the maximum value, the signaling is reset. If the number of the reset times reaches the configured maximum value, the system releases the service, which causes the call drop. The default configuration only ensures that the unexpected error blocks do not cause a call drop. In certain scenarios with poorer coverage, however, the signaling reset results in the call drop and causes the resources occupied by the service to be released. In certain scenarios with more burst interference or remarkable pinpoint effect, the block error rate may reach 100%. If the call drop rate is required to be not too high in such scenarios, you can appropriately increase the number of retransmission times to weaken the impact of the burst interference. This parameter is configured on the RNC.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 59
Cell Parameter Adjustment 7. RSCP (Inter-RAT Hard Handoff Threshold) After the inter-frequency measurement is started, the UE starts measuring the interfrequency cells. If the signal quality of the inter-frequency cells is higher than the threshold, the RNC initiates the inter-frequency handoff. You can configure the parameter based on the threshold for enabling or disabling the compression mode. If the parameter value is smaller, the handoff is triggered earlier. If the parameter value is greater, the triggering of the hard handoff is delayed. In this way, you can control the handoff area or reduce the call drop rate.
8. GsmRSSICSThd and GsmRSSIPSThd GsmRSSICSThd and GsmRSSIPSThd specify the inter-system handoff thresholds of the CS service and the PS service respectively. The method for setting the two parameters is the same as that for setting the inter-frequency hard handoff threshold.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 60
Contents 1. Definition and classification
2. Causes and handling process
3. Solutions
4. Case analysis
5. Concerns in various network optimization phases Training.huawei.com
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 61
4 Case analysis
4.1 Cases of call drop caused by poor coverage
4.2 Cases of call drop caused by interference
4.3 Cases of call drop caused by handoff
4.4 Cases of call drop caused by other reasons
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 62
Cases of Call Drop Caused by Poor Coverage To analyze cases of the call drop caused by poor coverage, you must take the following issues into account: Pilot frequency coverage and service coverage Uplink coverage and downlink coverage Measurement results recorded by the Scanner and UE EcIo, RSCP, and SC of the CPICH
Call drop location
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 63
Cases of Call Drop Caused by Poor Coverage
The call drop occurs on the SC314 cell, the coverage edge of the 3G network. Before the call drop, the UE measurement suggests that the No.314 cell is only included in the active set rather than the monitored set; the RSSI is low; the SIR is negative; the transmit power of the UE reaches the maximum.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 64
Cases of Call Drop Caused by Poor Coverage
The Ec/Io measured by the UE and that measured by the scanner shows the same degradation trend. The RSCP measured by the UE and that measured by the scanner shows the same degradation trend.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 65
4 Case analysis
4.1 Cases of call drop caused by poor coverage
4.2 Cases of call drop caused by interference
4.3 Cases of call drop caused by handoff
4.4 Cases of call drop caused by other reasons
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 66
Cases of Call Drop Caused by Interference
Cases of call drop caused by interference
The interference is subdivided into uplink interference and downlink interference. Materials are not available.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 67
4 Case analysis
4.1 Cases of call drop caused by poor coverage
4.2 Cases of call drop caused by interference
4.3 Cases of call drop caused by handoff
4.4 Cases of call drop caused by other reasons
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 68
Cases of Call Drop Caused by Handoff
As shown in this figure, the call drop does not occur at the edge of the 3G network coverage area. HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 69
Cases of Call Drop Caused by Handoff
The call drop occurs in the area where the best cell changes rapidly.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 70
Cases of Call Drop Caused by Handoff
Before the call drop, the Ec/Io measured by the UE is decreased to lower than -21 dB, whereas the Ec/Io measured by the scanner is still above -11 dB. HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 71
Cases of Call Drop Caused by Handoff
Before the call drop, the best cell measured by the UE is the SC009 cell, whereas the best cell measured by the scanner is the SC018 cell. After the call drop, the UE camps on the SC018 cell rapidly. HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 72
Cases of Call Drop Caused by Handoff
Before the call drop, the SC018 cell is not measured in the monitored set of the UE. The neighbor relation is found to be defined in the neighbor list. Therefore, the possible call drop cause is that the best cell changes rapidly from the SC009 cell to the SC011 cell and SC018 cell, and thus the UE fails to perform the soft handoff timely. HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 73
Cases of Call Drop Caused by Handoff
The SC018 cell is not the best cell here. Serious cross coverage exists in the SC018 cell. Upon the call drop, the RSCP is over -75 dBm. Therefore, you must increase the down tilt of the SC018 cell, control the coverage, and optimize the primary cell of the call drop location.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 74
4 Case analysis
4.1 Cases of call drop caused by poor coverage
4.2 Cases of call drop caused by interference
4.3 Cases of call drop caused by handoff
4.4 Cases of call drop caused by other reasons
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 75
Cases of Call Drop Caused by Other Reasons
The material is not available.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 76
Contents 1. Definition and classification
2. Causes and handling process
3. Solutions
4. Case analysis
5. Concerns in various network optimization phases Training.huawei.com
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 77
5 Concerns in Various Network Optimization Phases
5.1 Concerns in various network optimization phases
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 78
Concerns in Various Network Optimization Phases Network
optimization procedure
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 79
Concerns in Various Network Optimization Phases
The entire network optimization process consists of the following phases: Sign the project contract Optimize the network Generate the network optimization report Here, we focus on the causes of the call drop in phases from the single site test phase to the subsequent acceptance phase.
1. Single site test phase In the single site test phase, analyze the equipment problem to locate the abnormal call drop cause. If the call drop occurs during the drive test, check whether the call drop is caused by the poor coverage.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 80
Concerns in Each Phase 2. RF optimization phase Evaluation before the optimization During the evaluation phase, check the drive test results for call drop rate indexes and learn about the call drop rate of the entire network according to the measurement analysis. In this phase, emphasize on and differentiate call drops caused by poor coverage, interference, or untimely handoff. In addition, the call drops caused by the untimely handoff should be taken into account.
RF optimization The emphasis of this phase is to check whether call drops are caused by the poor coverage or strong interference. Check whether such call drop problems can be solved by adjusting engineering parameters of the antenna. In addition, call drops caused by the untimely handoff should be taken into account. Check whether the corner or pinpoint effect can be avoided by adjustment of the antenna.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 81
Concerns in Each Phase 3. Parameter optimization phase If certain call drops cannot be avoided by RF optimization or the RF optimization cannot be performed in some scenarios, optimize parameters to solve these problems after the RF optimization. In this phase, lay special stress on call drops caused by the handoff, inter-frequency handoff, and inter-RAT handoff. Generally, call drops due to latter causes occur in indoor area or subway. In this case, carry out the walking dialing test accordingly and trace messages of the single user on the RNC for data analysis.
4. Acceptance phase To evaluate the optimization effect, collect drive test indexes and measurements related to the call drop rate during the optimization and acceptance phases. Not all these call drop problems are required to be solved, but you are advised to analyze the detailed causes of each call drop and put forward further suggestions on the future optimization.
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 82
Thanks! WWW.HUAWEI.COM
HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI Confidential
Page 83
View more...
Comments
