User Manual Pioneer Vsa e06 e

You can read the recommendations in the user guide, the technical guide or the installation guide for PIONEER VSA-E06. You'll find the answers to all your questions on the PIONEER VSA-E06 in the user manual (information, specifications, safety advice, size, accessories, etc.). Detailed instructions for use are in the User's Guide. User manual PIONEER VSA-E06 User guide PIONEER VSA-E06 Operating instructions PIONEER VSA-E06 Instructions for use PIONEER VSA-E06 Instruction manual PIONEER VSA-E06

Your user manual PIONEER VSA-E06

Manual abstract: 24 Digital Input Default Settings 25 Connecting Speakers . 26 Placing Your Speakers . 27 Speaker placement . 27 AC Power Cord . 28 AC Outlet [switched 100 W max] 28 4 En Table of Contents Adjusting the Brightness of the Display (DISPLAY DIMMER) . 64 Status Display 65 THX Ultra2 Subwoofer Setup 96 Surround Back Speaker Position . 97 QUICK START GUIDE PREPARATION Techno Tidbits & Problem-solving . 98 Remote Control of Other Components 66 Setting Up the Remote Control to Control Other Components . 66 Recalling Settings Stored in the Remote Control . 66 Programming Signals from Other Remote Controls (LEARNING Mode) 68 Locking the Settings 69 Using the Remote Control with Other Components 70 DVD and TV operations 70 Setting up the DIRECT FUNCTION . 71 Dolby . 98 Dolby Digital . 98 Dolby Pro Logic II . 99 Dolby Digital Surround EX 99 MPEG Audio . 99 DTS . 100 DTS 100 DTS-ES 100 DTS Neo:6 . 100 DTS 96/24 100 THX . 100 Speaker Placement Information . 102 i.LINK Related Messages . 104 Troubleshooting . 105 Specifications . 112 PREPARATION Using Other Functions 72 Recording from Audio/Video Components . 72 Record monitor (TAPE 2 MONITOR) . 72 Speaker System B Setup . 73 Stereo playback in another room 73 Bi-amping the front speakers 73 Bi-wiring your speakers . 73 Switching A/B Speaker System . 74 Connecting Additional Amplifiers 75 Pre Out Power Setup . 76 The PIONEER SR System: Operating other PIONEER components . 76 Multi Operations 77 Performing multi operations . 78 System off 79 Using System off 80 Editing Remote Control Screen Names (ITEM MEMO) . 81 Editing Buttons Names (KEY LABEL) . 82 Resetting the Main Unit 84 Resetting the Remote Control 84 SURROUND SETUP BASIC Advanced Setup 85 Assigning the Digital Inputs 85 Assigning the Component Video Inputs 86 Assigning i.LINK Inputs . 87 Expert Setup . 89 OSD (On-screen Display) ADJUSTMENT . 90 BASS PEAK LEVEL . 91 DYNAMIC RANGE CONTROL 92 MULTI CH IN SELECT . 93 FUNCTION RENAME 94 HI-BIT/HI-SAMPLING 95 THX Audio Setup . 96 5 En EXPERT Before You Start Checking the Supplied Accessories Please check that you have received all of the following supplied accessories. Touch Pen Remote Control Unit (attached to the back of the remote control) U-shaped connectors x 2 (attached to back of amplifier) AC power cord · Operating Instructions · Reference Calibration disc "AA" IEC LR6 batteries x 4 Microphone Cushion for Remote x 4 · Multi-Channel Audio Speaker Setting Guide Preparing the Remote Control Loading the batteries Load the batteries into the remote control as shown below. The remote control uses a lot of power due to the LCD display so please use alkaline batteries. Depending on individual use you may have to change the batteries fairly often but most users should be able to get an average of 1-3 months of battery life. When you notice a decrease in the operating range or if the alarm sounds (see below), replace all batteries with new ones. NOTE: After replacing the batteries, the touch panel will need re-adjusting (see p. 8-9). "AA" IEC LR6 1 \ CAUTION! 2 · ª · batteries x 4 · ª ª · ª 3 \ Incorrect use of batteries may result in such hazards as leakage and bursting. Observe the following precautions. · Never use new and old batteries together. · Insert the plus and minus sides of the batteries properly according to the marks in the battery case. · Batteries with the same shape may have different voltages. Do not use different batteries together. · When disposing of used batteries, please comply with governmental regulations or environmental public institution's rules that apply in your country or area. Remote Control Battery Alarm When the batteries get too weak to operate the remote control properly an alarm will sound and a warning screen will appear on the remote. Change the batteries as shown above. This must be done within five minutes of the alarm sounding or all your remote control settings will be cleared. Change Battery !! OK ? SIZE AA, LR6 6 En Before You Start The Touch Pen & Lock The touch pen is located in the back right-hand corner of the remote control..

Your user manual PIONEER VSA-E06

Powered by TCPDF (www.tcpdf.org)