Unified Storage Management Final Lab Guide Vnx Lab Guide 2014

VNX Unified Storage Management Lab Guide January 2014

EMC Education Service

Copyright Copyright © 1996, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012 2013, 2014 EMC Corporation. All Rights Reserved. EMC believes the information in this publication is accurate as of its publication date. The information is subject to change without notice. THE INFORMATION IN THIS PUBLICATION IS PROVIDED “AS IS.” EMC CORPORATION MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WITH RESPECT TO THE INFORMATION IN THIS PUBLICATION, AND SPECIFICALLY DISCLAIMS IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Use, copying, and distribution of any EMC software described in this publication requires an applicable software license. EMC2, EMC, Data Domain, RSA, EMC Centera, EMC ControlCenter, EMC LifeLine, EMC OnCourse, EMC Proven, EMC Snap, EMC SourceOne, EMC Storage Administrator, Acartus, Access Logix, AdvantEdge, AlphaStor, ApplicationXtender, ArchiveXtender, Atmos, Authentica, Authentic Problems, Automated Resource Manager, AutoStart, AutoSwap, AVALONidm, Avamar, Captiva, Catalog Solution, C-Clip, Celerra, Celerra Replicator, Centera, CenterStage, CentraStar, ClaimPack, ClaimsEditor, CLARiiON, ClientPak, Codebook Correlation Technology, Common Information Model, Configuration Intelligence, Configuresoft, Connectrix, CopyCross, CopyPoint, Dantz, DatabaseXtender, Direct Matrix Architecture, DiskXtender, DiskXtender 2000, Document Sciences, Documentum, elnput, E-Lab, EmailXaminer, EmailXtender, Enginuity, eRoom, Event Explorer, FarPoint, FirstPass, FLARE, FormWare, Geosynchrony, Global File Virtualization, Graphic Visualization, Greenplum, HighRoad, HomeBase, InfoMover, Infoscape, Infra, InputAccel, InputAccel Express, Invista, Ionix, ISIS, Max Retriever, MediaStor, MirrorView, Navisphere, NetWorker, nLayers, OnAlert, OpenScale, PixTools, Powerlink, PowerPath, PowerSnap, QuickScan, Rainfinity, RepliCare, RepliStor, ResourcePak, Retrospect, RSA, the RSA logo, SafeLine, SAN Advisor, SAN Copy, SAN Manager, Smarts, SnapImage, SnapSure, SnapView, SRDF, StorageScope, SupportMate, SymmAPI, SymmEnabler, Symmetrix, Symmetrix DMX, Symmetrix VMAX, TimeFinder, UltraFlex, UltraPoint, UltraScale, Unisphere, VMAX, Vblock, Viewlets, Virtual Matrix, Virtual Matrix Architecture, Virtual Provisioning, VisualSAN, VisualSRM, Voyence, VPLEX, VSAM-Assist, WebXtender, xPression, xPresso, YottaYotta, the EMC logo, and where information lives, are registered trademarks or trademarks of EMC Corporation in the United States and other countries. All other trademarks used herein are the property of their respective owners. © Copyright 2014 EMC Corporation. All rights reserved. Published in the USA.

Revision Date: January 2014 Revision Number: MR-7xP-VNXUNIDM_5.33/8.1/2.1

Document Revision History

EMC Educational Services

Rev #

File Name

Date

1.0

VNX Unified Deploy and Management Lab Guide

05/2011

1.1

VNX Unified Deploy and Management Lab Guide

06/2011

1.2

VNX Unified Deploy and Management Lab Guide

09/2011

1.3

VNX Unified Deploy and Management Lab Guide

10/2011

1.4

VNX Unified Deploy and Management Lab Guide

02/2012

1.5

VNX Unified Deploy and Management Lab Guide

03/2012

1.6

VNX Unified Deploy and Management Lab Guide

08/2012

2.0

VNX Unified StorageManagement Lab Guide

10/2013

2.1

VNX Unified StorageManagement Lab Guide

01/2014

3

Table of Contents COPYRIGHT............................................................................................................. 2 DOCUMENT REVISION HISTORY.............................................................................. 3 TABLE OF CONTENTS .............................................................................................. 4 PRE-LAB EXERCISES INTRODUCTION ....................................................................... 7 LAB EXERCISE: INTRODUCTION TO EMC UNISPHERE ............................................. 11 LAB: PART 1 – UNISPHERE GENERAL NAVIGATION ............................................................13 END OF LAB EXERCISE PART 1 ........................................................................................24 LAB: PART 2 – UNISPHERE FOR FILE NAVIGATION ..............................................................25 END OF LAB EXERCISE PART 2 ........................................................................................30 LAB: PART 3 – UNISPHERE FOR BLOCK NAVIGATION..........................................................31 END OF LAB EXERCISE PART 3 ........................................................................................41 LAB: PART 4 – INVOKING A CLI COMMAND FROM UNISPHERE.............................................42 END OF LAB EXERCISE...................................................................................................45 THIS PAGE INTENTIONALLY LEFT BLANK ............................................................... 46 LAB EXERCISE: IMPLEMENTING UNISPHERE SECURITY .......................................... 47 LAB: PART 1 – VERIFY DOMAIN SECURITY .......................................................................49 END OF LAB EXERCISE PART 1 ........................................................................................50 LAB: PART 2 – CREATE LOCAL FILE ACCESS FOR GLOBAL USER ............................................51 END OF LAB EXERCISE...................................................................................................56 LAB EXERCISE: VERIFY VNX SYSTEM CONFIGURATION .......................................... 57 LAB: PART 1 – VERIFY SP CACHE SETTINGS .....................................................................59 LAB: PART 2 – VERIFY SP NETWORK CONFIGURATION.......................................................60 LAB: PART 3 – VERIFY HARDWARE AND STORAGE PROCESSOR PORTS...................................63 LAB EXERCISE: STORAGE CONFIGURATION ........................................................... 65 LAB: PART 1 – VERIFY STORAGE FOR VNX FILE ................................................................67 END OF LAB EXERCISE PART 1 ........................................................................................68 LAB: PART 2 – VERIFY BLOCK STORAGE POOL AND RAID GROUPS .......................................69 END OF LAB EXERCISE PART 2 ........................................................................................69 LAB #: PART 3 – CREATE CLASSIC LUNS .........................................................................70 END OF LAB EXERCISE PART 3 ........................................................................................72 LAB: PART 4 – CREATE THICK AND THIN LUNS.................................................................73 END OF LAB EXERCISE PART 4 ........................................................................................76 LAB: PART 5 – VERIFY HOT SPARE POLICY .......................................................................77 END OF LAB EXERCISE...................................................................................................77

EMC Educational Services

4

LAB EXERCISE: VERIFYING WINDOWS HOST SOFTWARE AND CONFIGURING HOST ACCESS TO VNX LUN ............................................................................................. 79 LAB: LAB: LAB: LAB:

PART 1 – VERIFY WINDOWS HOST SOFTWARE ..........................................................81 PART 2 – VERIFY THE VNX ARRAY IS CONFIGURED TO AUTO-MANAGE HOSTS .................84 PART 3 – CREATE AND POPULATE STORAGE GROUPS WITH EMC UNISPHERE -WINDOWS .85 PART 4 – CONFIGURE WINDOWS HOST ACCESS TO LUNS ...........................................87

THIS PAGE INTENTIONALLY LEFT BLANK ............................................................... 90 LAB EXERCISE: VERIFYING LINUX HOST SOFTWARE AND CONFIGURING HOST ACCESS TO VNX LUN .................................................... 91 LAB: PART 1 – VERIFY LINUX HOST SOFTWARE .................................................................93 LAB: PART 2 – CREATE AND POPULATE STORAGE GROUPS WITH EMC UNISPHERE -LINUX .......95 LAB: PART 3 – CONFIGURE LINUX HOST ACCESS TO LUNS .................................................97 LAB EXERCISE: CONFIGURING HOST ACCESS TO VNX LUNS - ESXI ....................... 103 LAB: PART 1 – CREATE AND POPULATE STORAGE GROUPS WITH EMC UNISPHERE -ESXI ...... 105 LAB: PART 2 – CONFIGURE ESXI HOST ACCESS TO LUNS ................................................ 107 LAB EXERCISE: ADVANCED STORAGE CONCEPTS ................................................. 109 LAB: PART 1 – EXPANDING POOL-BASED LUNS ............................................................. 111 LAB: PART 2 – EXPANDING RAID GROUP LUNS ........................................................... 114 LAB: PART 3 – MIGRATING LUNS............................................................................... 116 LAB EXERCISE: SNAPVIEW SNAPSHOTS ............................................................... 121 LAB: LAB: LAB: LAB: LAB:

PART 1 – VERIFY THE RESERVED LUN POOL .......................................................... 123 PART 2 – CREATE A SNAPVIEW SNAPSHOT ............................................................ 124 PART 3 - TEST PERSISTENCE OF A SNAPVIEW SESSION ............................................. 130 PART 4 - TEST THE SNAPVIEW ROLLBACK FEATURE ................................................. 131 PART 5 - START AND TEST A CONSISTENT SNAPVIEW SESSION ................................... 133

LAB EXERCISE: SNAPVIEW CLONES ..................................................................... 135 LAB: PART 1 –CLONE PRIVATE LUNS AND ENABLE PROTECTED RESTORE ........................... 137 LAB: PART 2 – CREATE AND TEST A CLONE ................................................................... 138 LAB: PART 3 – PERFORM A CLONE CONSISTENT FRACTURE .............................................. 145 THIS PAGE INTENTIONALLY LEFT BLANK ............................................................. 148 LAB EXERCISE: VNX SNAPSHOTS ......................................................................... 149 LAB: PART 1 – VERIFY THAT THE VNX SNAPSHOTS FEATURE IS LICENSED ............................ 151 END OF LAB EXERCISE PART 1 ..................................................................................... 152 LAB: PART 2 - CREATE A VNX SNAPSHOT WITH EMC UNISPHERE ..................................... 153 THIS PAGE INTENTIONALLY LEFT BLANK ............................................................. 164 LAB EXERCISE: DATA MOVER NETWORK CONFIGURATION ................................. 165 LAB: PART 1 – CONFIGURE NETWORKING ON VNX DATA MOVERS................................... 167 LAB EXERCISE: FILE SYSTEM CONFIGURATION AND MANAGEMENT ................... 171 LAB: PART 1 – CONFIGURE AND MANAGE A VNX FILE SYSTEM ........................................ 173 THIS PAGE INTENTIONALLY LEFT BLANK LAB ...................................................... 176

EMC Educational Services

5

EXERCISE: NFS FILE SYSTEM EXPORT AND PERMISSIONS .................................... 177 LAB: PART 1 – EXPORTING FILE SYSTEMS FOR NFS CLIENTS............................................. 179 LAB: PART 2 – ASSIGNING ROOT PRIVILEGES ................................................................ 186 LAB EXERCISE: VDM CONFIGURATION ................................................................ 191 LAB: PART 1 – SYSTEM SETUP FOR VDM IMPLEMENTATION ............................................ 193 LAB EXERCISE: CIFS IMPLEMENTATION ............................................................... 197 LAB: LAB: LAB: LAB:

PART 1 – PREPARING THE SYSTEM FOR CIFS .......................................................... 199 PART 2 – CREATE AND JOIN A CIFS SERVER ........................................................... 202 PART 3 – CREATE AND ACCESS CIFS SHARES ......................................................... 203 PART 4 – MOVE A VDM CONTAINING A CIFS SERVER ............................................. 207

THIS PAGE INTENTIONALLY LEFT BLANK ............................................................. 210 LAB EXERCISE: VNX SNAPSURE ........................................................................... 211 LAB: PART 1 – CONFIGURE SNAPSURE ......................................................................... 213 LAB: PART 2 – RESTORE AND REFRESH SNAPSHOTS WITH NFS ......................................... 219 LAB: PART 3 – RESTORE AND REFRESH SNAPSHOTS WITH CIFS ........................................ 223 APPENDIX: WINDOWS USER AND GROUP MEMBERSHIPS .................................. 227 APPENDIX: LINUX USERS AND GROUPS .............................................................. 228 APPENDIX: UNISPHERE BROWSER AND JAVA MESSAGES ................................... 229

EMC Educational Services

6

Pre-Lab Exercises Introduction Important

The following lab exercises provide the steps for setting up Windows and Linux to interact with the VNX-series storage system through Block and File connectivity. A few important notes! Note 1: Not all screen captures were made on the lab equipment you will be using and therefore may differ slightly from what you will see. Read each lab and step completely before attempting it; do not simply follow the pictures! Note 2: You will be sharing a VNX system with other students to perform the lab exercises. This lab guide and a corresponding Class Configuration Sheet are used together to perform the lab exercises. It is important to follow the naming convention for the objects you create by following the lab guide and referring to your configuration sheet for the unique names. In the lab guide objects or “items” specific to each student are identified with Bold Italic text. The corresponding “value” for the item is located on your specific student Class Configuration Sheet. So when you see Bold Italic text in the lab guide, you are required to use a value for the item that is located on your Class Configuration Sheet. Each lab exercise has a section labled “Preparing for the Lab” and is designed as a tear-out sheet. It lists the objects or “items” that will be identified with the Bold Italic text in the lab guide. You may use this section to record the values for each item from the Class Configuration Sheet. Refer to this tear-out to input the values for the specified items.

EMC Educational Services

7

Lab Equipment Layout

This is a diagram of the lab equipment setup you will use for completing the exercises. The setup has two halves; an A-side has odd-numbered equipment and a B-side that has even-numbered equipment. Each student will be assigned to a Student Desktop system and will have access to a VNX system and three other systems which will receive storage from the VNX; A Windows server, a Linux server and an ESXi server. The setup also includes a Windows Active Directory environment for Windows users to access CIFS storage from the VNX. It also includes a Linux LDAP environment for users to access NFS storage from the VNX. The Windows AD and Linux LDAP user and group environment are detailed in the lab guide Appendix. The setup includes multiple networks and network services for the VNX to operate in.

EMC Educational Services

8

Lab Access via VDC

Access to the lab setup is achieved through the EMC Virtual Data Center (VDC). The instructor will provide each student with a unique VDC account credential to use for completing the lab exercises. The specific VDC account is used to login to the VDC. The login will provide access to a user-specific Student Desktop system.

EMC Educational Services

9

Student Desktop

Each student will be automatically redirected to the Metro view of their specific Student Desktop Windows 8 system. Access the Desktop charm to get to the Desktop view. The Desktop view and its Task bar have been pre-configured with all the needed application icons needed for the lab exercises.

EMC Educational Services

10

Lab Exercise: Introduction to EMC Unisphere Purpose:

The purpose of this lab is to provide the students with an understanding of the EMC Unisphere interface concept and its navigation. This lab focuses on basic VNX storage system operations that IT professionals may be required to perform using the New Unisphere management Interface. Note: Screenshots used in this Lab Exercise are meant to be used as examples. You may have different values/data on your VNX system.

Tasks:

References:

EMC Educational Services

In this lab exercise, you will perform the following tasks: 

Login in Unisphere and validate storage System



Navigate the Unisphere for File and Block functions



Explore the Unisphere Help



Invoke a Command Line Interface (CLI) command



EMC Unisphere: Unified Storage Management Solution. A Detailed Review – White Paper – July 2012



VNX Command Line Interface Reference for Block.



VNX Command Line Interface Reference for File

11

Preparing for the Lab Please refer to your Class Configuration Sheet for this lab and record the values for each item listed. You will use these values for the lab exercise.

Student number:

__________________________________________________

VNX:

__________________________________________________

VNX Address (Control Station):

__________________________________________________

VNX Address (SPA):

__________________________________________________

VNX Address (SPB):

__________________________________________________

EMC Educational Services

12

Lab: Part 1 – Unisphere General Navigation Step Note

Action Your instructor will provide to you the information for connecting to the EMC Virtual Data Center (VDC). The VDC connection information includes a Web URL for the VDC and account credentials. The account provides you access to your Student Desktop system. You will use your Student Desktop system to access your VNX system and the other systems in the lab setup. Ask your instructor for assistance if you are having any difficulty connecting to the VDC or accessing your Student Desktop system.

EMC Educational Services

13

Step 1

Action Secure Connection to Unisphere:  From your Student Desktop, open a web browser. In the URL address section enter the VNX Address (Control Station) to access Unisphere. Note: You may encounter a series of browser and Java messages on initial Unisphere session establishment. Please refer to the Appendix section of this lab guide to see instructions for handling the messages. Note: By default, the VNX uses a self-signed certificate to establish a secure HTTP session between it and your browser. Self-signed certificates are not trusted by browsers and will issue a Security/Warning dialogue for the user to take action to proceed.  Click Continue to this website (not recommended)

EMC Educational Services

14

Step 2

Action Confirm the execution of any Java Applets: Unisphere is a Java-based web application and pop-up Java messages could be encountered. The user will need to take action to proceed. Note: You may encounter a series of browser and Java messages on initial Unisphere session establishment. Please refer to the Appendix section of this lab guide to see instructions for handling the messages. Note: Do Not update the version of Java installed on your Student Desktop. The version is maintained to ensure interoperability with the browser and the VNX OE code.  Check the Do not show this again… option and click Run to accept the execution of the Java Applet

EMC Educational Services

15

Step 3

Action Accept the Software Terms and Conditions: In Unified or File configurations, a dialogue box will be displayed with the Terms and Conditions to use the VNX Control Station operating environment.  Click Accept to agree and continue.

EMC Educational Services

16

Step 4

Action Unisphere Login:  At the EMC Unisphere login screen, login using the following settings: Name: sysadmin Password: sysadmin Use LDAP: unchecked Scope: Global  Click Login

The Unisphere Interface is launched and the Home Page displayed with the Dashboard screen.

EMC Educational Services

17

Step 5

Action The EMC Unisphere Title bar of the Unisphere interface has basic and advanced object Search options, a General Tab with options to set interface preferences, log and exit, and retrieve Unisphere Help. The Top Navigation bar has Previous and Next Icons to allow navigation back and forth, a Home Icon that shows the Dashboard screen, a System Dropdown menu to switch between VNX storage systems registered to the domain, and a context-Sensitive Menu Bar which varies depending on the system being managed: VNX for File/Unified and VNX for Block. Panels in a Dashboard screen display information about the storage system(s).

The panels displayed on the dashboard may be different depending on the storage system configuration and authentication scope. This appearance can be changed.  Click the Customize link in the upper right corner of the dashboard. The edit mode will open with the list of panels that can be dragged to the Dashboard.

EMC Educational Services

18

Step 6

Action Remove Panel from Dashboard:  On the Alerts by Severity panel, click the X (close) button from the menu on the top right corner of the panel.

Observe that the panel was removed from the Dashboard. 7

Move a Panel from its Position on the Dashboard:  Click on the top bar of the Overall Capacity panel and drag the window to the top left of the Dashboard.

Observe that the panels can be moved to different positions on the Dashboard. 8

Add a Panel to the Dashboard:  Click on Alerts by Severity icon on the top menu and drag the icon to the right of the Overall Capacity panel.

Observe that the panel was added to the Dashboard.

EMC Educational Services

19

Step 9

Action Restore the Dashboard to its default view:  Click on the Restore Defaults button to

Observe that the edit mode has closed and the Dashboard appearance has returned to the default configuration. 10

Explore the System List:  From the top Navigation Menu click on the System List option

Observe that the systems that are part of the storage domain are listed here.

EMC Educational Services

20

Step 11

Action Explore the Domains page:  Click on the Domains option.

A list of managed domains is displayed, including the local domain and any remote domains.  Select the Local domain. The systems that are part of this domain are displayed on the lower panel.  From the menu on the top right corner of the panel select the Tools icon, and select the Choose Columns option.  Uncheck the boxes for the Status, Software Revision, and Client Revision columns, and click OK.

Observe that the columns were removed from the table.

EMC Educational Services

21

Step 12

Action Explore the Alerts page:  Click on the Alerts option.

A green check mark indicates the system is functioning normally. An orange icon indicates a system error condition, and a yellow icon a system warning.  Select any record and click on Details.

Observe that a description of the alert is displayed with the option to save it to a text file on the client machine.

EMC Educational Services

22

Step 13

Action Verify the Certificates that were accepted for the session:  Double-click the Certificates label on the bottom of the Unisphere Interface Home page.

The list of system certificates and their status are displayed.

 Select one Certificate and click the Properties button. Click Details.

 Information about the certificate is displayed. Click Close to exit.

EMC Educational Services

23

Step 14

Action Explore some of the top Navigation options:  From the Top Navigation select the left arrow

Observe that the interface will launch the previous visited page (“Domains”).  Click the Home icon on the Top Navigation menu.

Observe that the interface will launch the Dashboard screen.

End of Lab Exercise Part 1

EMC Educational Services

24

Lab: Part 2 – Unisphere for File Navigation Step Note

1

Action In this exercise you will perform basic tasks to become more familiar with VNX for File operations using Unisphere. Some of the tasks can be completed in more than one way. Select your assigned storage system:  Select your VNX from the drop-down list

Note: The same operation can be performed by clicking on the system link at the Systems by Severity panel Observe that the context-Sensitive Menu Bar on the Top Navigation has changed based on the choice of object.

The Dashboard screen has also changed to display the information about the chosen storage system: system alerts, system information, and storage capacity.

EMC Educational Services

25

Step 2

Action Explore the Hardware for File components  On Top Navigation bar, click Systems > Hardware > Hardware for File.

Note: If you position the mouse over the menu option, and wait for 2 seconds, a sub-menu will open with the options for the choice. The Hardware for File inventory is displayed with the list of components.  Select one of the components, and click Properties.

The hardware component Properties dialogue box is displayed.  Click Cancel to close the Hardware Component Properties window.

EMC Educational Services

26

Step 3

Action Check the Control Station Properties:  From the System Management Task Pane on the right of the screen select the Control Station Properties link

Note: The screen above is displayed when the user log in using a global scope authentication. If the user is authenticated to the VNX Control Station using the local domain scope the screen below is presented.

The Control Station Properties dialogue box opens.  Read the information and click Cancel to close the Window

EMC Educational Services

27

Step 4

Action Check the status of the VNX Data Movers:  On the top of screen, select Hardware from the page bread-crumb links.

 Select Data Movers.  Select server_2 and click Properties. (Or right-click the server_2 and select the Properties option.)

 Read the information and click Cancel to close the Window.

EMC Educational Services

28

Step 5

Action Explore the Event Logs for File:  On the top of screen, select System from the page bread-crumb links. (Or click the System option from the Top Navigation bar).

 Select Monitoring and Alerts. The Monitoring and Alerts page is displayed.    

EMC Educational Services

Select Event Logs for File. Select server_2 from the “Show Events for:“ drop-down list. Select 1 week from the “Time Interval:” drop-down list. Select Error and Above from the “Severity Level:” drop-down list.

29

Step 6

Action Explore the Background Tasks for File:  On the top of screen, select Monitoring and Alerts from the page breadcrumb links.  Select Background Tasks for File. The Background Tasks for File page is displayed.  Select one task from the list.  Click on Properties.

 Read the logged information and click Cancel to close the window.

End of Lab Exercise Part 2

EMC Educational Services

30

Lab: Part 3 – Unisphere for Block Navigation Step Note

1

Action In this exercise you will perform basic tasks to become more familiar with Unisphere operations involving VNX for Block components. Some of the tasks can be completed in more than one way. Navigate to the Home Page displaying the All Systems Dashboard screen:  Click the Home Page icon or select All Systems from the drop-down list.

EMC Educational Services

31

Step 2

Action Open the System List page to view information about the VNX systems that are part of the storage domain:  Click the System List option. The page will display the list of systems with information about S/N, Model, and Software Revision.

 Select your assigned VNX system from the list and click Properties

Observe that the General tab will display information about the zoning Unique ID, iSCSI IQN, and the IP address configuration of the storage processors.  Explore the other tabs of the properties dialogue box. Observe that some of the block configuration can be done on this dialogue box.  Click Cancel to close the properties dialogue box.

EMC Educational Services

32

Step 3

Action Open Dashboard screen for your assigned storage system:  Click on the link of the VNX from the System List

Observe that the context-Sensitive Menu Bar on the Top Navigation has changed based on the choice of object.

The Dashboard screen has also changed to display the information about the chosen storage system: system alerts, system information, and storage capacity.

EMC Educational Services

33

Step 4

Action Storage Hardware page:  Navigate to System > Hardware > Storage Hardware

EMC Educational Services

34

Step 5

Action Explore the Block Storage hardware components page:  Click the column arrow that divides the main pane and the Task pane.

This will hide the Task Pane and expand the main pane – this will provide a better visualization of the hardware component graphics. Explore the components on the left pane of the page.  Click and expand the different components and observe the changes on the graphic on the main pane. Observe that Unisphere will highlight the component on the graphic.  Expand the SPs > SP A component by clicking the + icon next to them.  Click on the SPA component

Observe that Unisphere highlighted the SPA module on the graphic.

EMC Educational Services

35

Step 6

Action Storage Processor Properties:  Click the Properties button

The Properties dialogue box will open.  Explore the other tabs and click Cancel when done. 7

SP I/O module components:  Click on the + next to the IO modules and select any Present State slot  Click on the Show Diagram button A graphic of the I/O module will be displayed. 

EMC Educational Services

Click OK to close it.

36

Step 8

Action I/O module Description:  Click the Properties button A window will open with a description of the type of I/O module and status.

 Click OK to close it.

EMC Educational Services

37

Step 9

Action Explore the Event Logs for Block:  On the top of screen, select System from the page bread-crumb links. (Or click the System option from the Top Navigation bar).

 Select Monitoring and Alerts. The Monitoring and Alerts page is displayed.  Select SP Event Logs > Show SP A Event Log.  On the Event Viewer dialogue box, click Yes to confirm the retrieval of the event information.

The Event Viewer dialogue box opens with the events for all periods and categories. Observe that this view can be saved in a text file, printed or filtered.

 Click Cancel to close the Event Viewer window.

EMC Educational Services

38

Step 10

Action Creation of Reports with information about VNX for Block:  On the top of screen, select System from the page bread-crumb links.  Select Reports. The Reports page is displayed.  Select the Reports Wizard.

 Click Next to continue.  Expand the System Profile on the “Select Report Sections” and check the boxes for the following information: SP Summary SP Port Details I/O Module Information

 Check the “Launch browser…” box and click Next to continue.

EMC Educational Services

39

Step 11

Action Launch the Report in the web browser:  Click Finish

 Unisphere spawns a new page for displaying the report. The browser displays an ActiveX message. Click the Allow blocked content button to display the report. Refresh the browser page if the ActiveX message disappears before clicking the button.

The web page captures the information and generates a report in a XML format. The report can be automatically launched or the user can click the View button to retrieve it.

EMC Educational Services

40

Step 12

Action Change the Report View on the XML page:  Click the System Profile option and select the SP Summary

 Click the SP Port Details option

 Click I/O Module Information to view the other page View  Navigate the General and View All options. Close the browser when done and click Finish to close the Wizard dialogue box.

End of Lab Exercise Part 3

EMC Educational Services

41

Lab: Part 4 – Invoking a CLI command from Unisphere Step

Action

Note

There may be events that require invoking a CLI command. This exercise provides you with the ability to invoke a VNX OE for File CLI command via Unisphere. The use of 3rd party applications for command line entry is also acceptable. In order to illustrate a comparison you will view information via Unisphere and then view the information via the command line output.

1

Navigation to Unisphere Command page: The next three steps illustrate how Unisphere and command line output display similar information.  Navigate to the System page  Expand the Control Station CLI Task Pane to expose its “Run Command” link.

EMC Educational Services

42

Step 2

Action Opening Unisphere Command page:  From the Task pane click Run Command

The Command page opens for entering commands

EMC Educational Services

43

Step 3

Action Displaying Data Movers – CLI:  Inside the Command: box enter the following command: nas_server –list The command will provide the output on the same window

Where: Id type acl slot groupID state

ID of the Data Mover. Type assigned to Data Mover. Access control value assigned to the Data Mover or VDM. Physical slot in the cabinet where the Data Mover resides. ID of the Data Mover group. Whether the Data Mover is enabled=0, disabled=1, failed

over=2. name

Name given to the Data Mover.

What are the names of the Data Movers: ___________, ____________. 4

Unisphere and CLI output differences – Unisphere output:  From the Top Navigation Bar click Storage > Storage Configuration > File Systems. There should not be any file systems listed in the task page. This is expected.

EMC Educational Services

44

Step 5

Action Unisphere and CLI output differences – CLI output:  Click Systems on the top Navigation bar  And click the Run Command link on the Task pane.  Inside the Command: box enter the following command: nas_fs –list

You see many file systems listed in the task page. This is because Unisphere does not display the root file systems but the CLI does.  Close the Control Station CLI window.

End of Lab Exercise

EMC Educational Services

45

This page intentionally left blank

EMC Educational Services

46

Lab Exercise: Implementing Unisphere Security Purpose:

This lab exercise explains how to select a system on the Storage Domain to be a Domain Master node. The lab will also demonstrate how to create a user-defined role, and associate it to a new local group. The lab exercise will then explain how to create a Global User Account and associate with the created local group. Synopsis: You have just implemented a successful installation of a VNX array for your customer. The VNX system has already been set up with prerequisite software and enablers. The hosts, however, will need to be setup and have all necessary software installed since they are without it presently. The customer hired a new member for the Storage Administration Team, who experience with a VNX feature. The new member is not yet a part of the Company’s Microsoft AD. The head of the IT department, would like to give the member administrative privileges over the VNX feature.

Tasks:

References:

EMC Educational Services

In this lab exercise, you will perform the following tasks: 

Configure and Verify Domain Security



Create a Global User account on the VNX



Create a Local Group on the VNX



Define a New Role

Security Configuration Guide for VNX

47

Preparing for the Lab Please refer to your Class Configuration Sheet for this lab and record the values for each item listed. You will use these values for the lab exercise.

Student number:

__________________________________________________

VNX:

__________________________________________________

VNX Address (Control Station):

__________________________________________________

VNX Address (SPA):

__________________________________________________

VNX Address (SPB):

__________________________________________________

User-Defined Role Name:

__________________________________________________

User-Defined Role Description:

__________________________________________________

User-Defined Role Privileges:

__________________________________________________

Local Group Name:

__________________________________________________

Local Group Role:

__________________________________________________

Global User:

__________________________________________________

Global User Primary Group:

__________________________________________________

Global User Group (Role):

__________________________________________________

EMC Educational Services

48

Lab: Part 1 – Verify Domain Security Step

Action

Note (If you are not already logged in to your “Student Desktop”) Connect to your “Student Desktop” via your VDC connection. Ask your instructor for assistance if you are having any difficulty 1

Unisphere login:  From your Student Desktop, open a web browser and enter the VNX Address (Control Station) in the URL address section.  At the EMC Unisphere login screen, login using the following settings: Name: sysadmin Password: sysadmin Use LDAP: unchecked Scope: Global  Click Login

2

Verify Domain Security:  From the Top Navigation bar in Unisphere, ensure that the All Systems option is selected from the drop-down list.  Then click the Domains option.

3

Domain Configuration:  From the right-side Tasks Pane, in the Local Domain section, click the Select Domain Master link.

EMC Educational Services

49

Step 4

Action Domain Master:  Observe the IP address listed in the Master Node IP Address field.

What system does this IP Address reference? _____________________________________________________________________ Which IP Addresses can fulfill the role of Master Node? _____________________________________________________________________  Click Cancel to close the window.

End of Lab Exercise Part 1

EMC Educational Services

50

Lab: Part 2 – Create Local File Access for Global User Step 1

Action Manage License for File In order to demonstrate the creation of a user-defined role on the next lab step, the license for some VNX features must be enabled on the VNX storage system.  From the navigation bar drop-down, select your assigned VNX system.  Click the Settings option on the navigation bar.

 From the right-side Tasks pane in the More Setting section, select Manage Licenses for File.  Verify that all the licenses are checked.

 If needed, enable any unchecked licenses by checking a license one at a time and selecting OK. (This may take a short amount of time.)  Click Cancel to close the window.

EMC Educational Services

51

Step 2

Action Create a user-defined role: In this step, you will create a new administrative role with the privileges that are described in your class configuration sheet.  Navigate to Settings > Security > User Management > User Customization for File and select the Roles tab.  Click the Create button.

 Create a role with the information you recorded in “Preparing for the Lab”: Role Name: User-Defined Role Name Description : User-Defined Role Description Privileges : User-Defined Role Privileges (Expand the Privileges Category in order to select the privilege object and access level)  Click OK when you are done. Look at the List of Roles – Observe that the role that was just created appears under the Roles tab in the User Customization for File window.

EMC Educational Services

52

Step 3

Action Create a Local Group:  From the User Customization for File window, select the Groups tab.  Click the Create button.

 Create a group with the recorded information: Group Name : Local Group Name GID: Auto select Role : Local Group Role Group Type: Local Only Group  Click OK when you are done. The newly created group should appear under the Groups tab in the User Customization for File window as a Local Group type.  Close the User Customization for File window.

EMC Educational Services

53

Step 4

Action Create a Global User Account:  Navigate to Settings > Security > User Management > Global Users.  Click Add

 Create a user with the information in your class configuration sheet: Username : Global User Password: sysadmin1 Storage Domain Role: Operator  Click OK when you are done.  Click Yes to confirm the addition of the new Global User.  Click OK on the dialogue box that states the operation was successfully completed. The newly created user should appear under the Global User Management window.  Click OK to close the Global User Management window.

EMC Educational Services

54

Step 5

Action Assign the group role to the new user  Navigate to Settings > Security > User Management > User Customization for File and select the Users tab.  Select the Global User you have created and click Properties.

 Configure the User Properties settings with the following information: Primary Group: Global User Primary Group Group (Role) Membership: Global User Group (Role) Client Access: CLI Access allowed  Click OK The modified user is displayed under the “User Customization for File” window with the “Operator” and new assigned roles.  Close the “User Customization for File” window.

EMC Educational Services

55

Step 6

Action Unisphere Login for Role-based user:  Logout from Unisphere and log back in as the Global User (case sensitive) with the following settings: Name: Global User Password: sysadmin1 Use LDAP: unchecked Scope: Global  Click Login Verify that the new user account is able to log into the system.

7

Role-based user access in Unisphere: Observe that the role of the user does not have creation and modify rights on tasks not related to the assigned role.  From the Dashboard view, select your VNX from the navigation bar dropdown list.  Navigate to System > Monitoring and Alerts > Notifications for File.

 Navigate through the tabs of the Notifications for File window. Observe that the “Create” button is grayed out in each one of the tabs. The account is not able to make any modifications to created events.  Logout & Exit Unisphere.

End of Lab Exercise

EMC Educational Services

56

Lab Exercise: Verify VNX System Configuration Purpose:

In this lab, you will verify the VNX storage system SP (Storage Processor) cache settings, networking and port configuration.

Tasks:

In this lab exercise, you will perform the following tasks:    

EMC Educational Services

Verify SP cache settings Verify SP networking configuration Verify hardware and SP ports Verify iSCSI ports

57

Preparing for the Lab Please refer to your Class Configuration Sheet for this lab and record the values for each item listed. You will use these values for the lab exercise.

Student number:

__________________________________________________

VNX:

__________________________________________________

VNX Address (Control Station):

__________________________________________________

VNX Address (SPA):

__________________________________________________

VNX Address (SPB):

__________________________________________________

EMC Educational Services

58

Lab: Part 1 – Verify SP Cache Settings Step 1

Action System Login:  (If you are not already logged in to your “Student Desktop”) Connect to your “Student Desktop” via your VDC connection.  From your Student Desktop, open a browser and login to Unisphere on your assigned VNX using the VNX Address (Control Station) and the user credentials: sysadmin/sysadmin with Scope Global selected.

2

Verify SP Cache Settings:  Select your VNX from the All Systems drop down menu  From the navigation bar select System. From the right-side Tasks pane “System Management” section click the System Properties link.  Select the SP Cache tab

What is considered a Read and a Write Cache Hit? _______________________________ What would happen with Write cache is disabled? _______________________________  Click Cancel to close the window.

End of Lab Exercise Part 1

EMC Educational Services

59

Lab: Part 2 – Verify SP Network Configuration Step 1

Action Access SP network settings:  From the navigation bar select Settings. From the right-side Tasks pane “Network Settings” section click the Edit Network Settings – SPA link.

EMC Educational Services

60

Step 2

Action Verify SP network configuration:  Click the Network tab.  From Management Port Settings section, notice that the Requested Settings: drop-down list is grayed out. This is due to the VNX Unified system having its SP Management ports cabled into the system’s internal network. Review the Link Status settings for network speed and duplex.

 From the Virtual Port Properties window, verify that virtual port 0 displays the VNX Address (SPA).  Click on Virtual Port 0 and select Properties.  Verify that the settings are as follows: IP Addess: VNX Address (SPA) Gateway: 192.168.1.254 Subnet Mask: 255.255.255.0 Please notify your instructor if the settings are not correct.  Click Cancel to close the window.

EMC Educational Services

61

Step 3

Action Verify DNS configuration:  From the navigation bar drop-down list, select All Systems. Click on the navigation bar Domains option.  From the right-side Task pane Local Domain section, click the Configure DNS link.  Verify the following DNS settings: DNS Domain Suffix: hmarine.test DNS Server IP Address: 192.168.1.50 Domain Search List: hmarine.test  Click OK to close the window.

End of Lab Exercise Part 2

EMC Educational Services

62

Lab: Part 3 – Verify Hardware and Storage Processor Ports Step 1

Action Explore Storage Hardware:.  From the navigation bar drop-down list, select your VNX.  Navigate to System > Hardware > Storage Hardware  From the Storage Hardware Component tree, expand the SPs container and then expand SP A > IO Modules > Slot A1.  Starting at the top of the tree, click SP A. View the picture on the right side of the window. It should highlight the selected component in green.  Continue to highlight objects from the tree structure and view the components on the right.  Select Port 1 and click Properties to view the port details. What is the actual port speed listed? ___________________________  Click Cancel to close the window.

2

Verify iSCSI ports:  Next, navigate to Settings > Network > Settings for Block  From the “SP-Port” column select A-1 and click Properties to view port details. What is the actual port speed listed? ___________________________  Click Cancel to close the window.

End of Lab Exercise

EMC Educational Services

63

This page intentionally left blank

EMC Educational Services

64

Lab Exercise: Storage Configuration Purpose:

In this lab, you will verify and provision storage for a VNX Unified system in preparation for configuring file systems and attaching block hosts.

Tasks:

In this lab exercise, you will perform the following tasks:     

EMC Educational Services

Verify storage for a VNX for File platform Verify Pools and RAID Groups Create Classic LUNs Create Thin LUNs and Thick LUNs Verify hot spare policy

65

Preparing for the Lab Please refer to your Class Configuration Sheet for this lab and record the values for each item listed. You will use these values for the lab exercise.

Student number:

__________________________________________________

VNX:

__________________________________________________

VNX Address (Control Station):

__________________________________________________

VNX Address (SPA):

__________________________________________________

VNX Address (SPB):

__________________________________________________

RG5 LUN ID:

__________________________________________________

RG5 LUN Name:

__________________________________________________

RG10 LUN ID:

__________________________________________________

RG10 LUN Name:

__________________________________________________

Thick LUN ID:

__________________________________________________

Thick LUN Name:

__________________________________________________

Thin LUN ID:

__________________________________________________

Thin LUN Name:

__________________________________________________

RG5 LUN Folder:

__________________________________________________

RG10 LUN Folder:

__________________________________________________

Pool LUN Folder:

__________________________________________________

EMC Educational Services

66

Lab: Part 1 – Verify Storage for VNX File Step 1

Action System Login:  (If you are not already logged in to your “Student Desktop”) Connect to your “Student Desktop” via your VDC connection.  From your Student Desktop, open a browser and login to Unisphere on your assigned VNX using the VNX Address (Control Station) and the user credentials: sysadmin/sysadmin with Scope Global selected.

2

Verify File Pool:  From the navigation bar drop-down list, select your VNX.  Navigate to Storage > Storage Configuration > Storage Pools  Verify that there is a storage pool created with the name of File Pool which is made up of mixed disks  Select File Pool and click Properties to answer the following questions What types of disk makes up this storage pool? ___________________________________ Which RAID configuration is being used? _________________________________________  Click Cancel to close the window.

EMC Educational Services

67

Step 3

Action Verify Pool LUN assignment:  Navigate to Hosts > Storage Groups  Select the ~filestorage storage group and click Properties (This is the Storage Group for the File storage of the VNX)  Select the LUNs tab You should see several LUNs starting with the word “File” in the list of Selected LUNs. These LUNs have been added from the File storage pool. These LUNs have also been discovered by the VNX OE for File, notice that each LUN ends in a “d” and a number. These are the disk volumes that are associated with each LUN.

 Click Cancel to close the window. 4

Verify storage pools for File:  Navigate to Storage > Storage Configuration > Storage Pools for File. The page displays the mapped pool named File Pool. The storage space from this pool will be used to create file systems.

End of Lab Exercise Part 1

EMC Educational Services

68

Lab: Part 2 – Verify Block Storage Pool and RAID Groups Step 1

Action Verify Storage Pool:  Navigate to Storage > Storage Configuration > Storage Pools  Verify that there is a storage pool created with the name of Block Pool which is made up of mixed disks  Select Block Pool and click Properties to answer the following questions What Drive Types are used for this storage pool? ___________________________________ Which RAID configurations are used for this pool? __________________________________  Click Cancel to close the window.

2

Verify RAID Groups:  Select the RAID Groups tab on the Storage Pools page to verify if there are any RAID groups created  You should see two RAID groups created; RAID Group 5 made up of 5 disks and RAID Group 10 made up of 4 disks.

End of Lab Exercise Part 2

EMC Educational Services

69

Lab #: Part 3 – Create Classic LUNs Step 1

Action Create LUNs on RAID Group 5:  Navigate to Storage > LUNs  From the LUNs tab click Create  Create LUNs in the General tab with the following settings: Storage Pool Type: RAID Group RAID Type: RAID5: Distributed Parity (High Throughput) Storage Pool for new LUN: 5 User Capacity: 5 GB LUN ID: RG5 LUN ID Number of LUNS: 6 Select the Name radio button. In the Name field enter your RG5 LUN Name Starting ID: RG5 LUN ID  Select the Advanced tab and configure the following settings: Use SP Write Cache: checked FAST Cache: unchecked No Initial Verify: unchecked Set Default Owner: Auto  Click Apply, Yes and OK to complete the operation. Please stop and with your instructor verify you have created six (6) 5 GB LUNs with a LUN ID range starting with the RG5 LUN ID. If the LUNs you created do not match the settings specified, with instructor assistance correct the settings before proceeding. Subsequent lab exercises depend upon the LUNs created to be as specified.

EMC Educational Services

70

Step 2

Action Create LUNs on RAID Group 10:  From the LUNs tab click Create  Create LUNs in the General tab with the following settings: Storage Pool Type: RAID Group RAID Type: RAID1/0: Mirrored Redundant Individual Access Storage Pool for new LUN: 10 User Capacity: 5 GB LUN ID: RG10 LUN ID Number of LUNS: 4 Select the Name radio button. In the Name field enter your RG10 LUN Name Starting ID: RG10 LUN ID  Select the Advanced tab and configure the following settings: Use SP Write Cache: checked FAST Cache: unchecked No Initial Verify: unchecked Set Default Owner: Auto  Click Apply, Yes and OK to complete the operation. Please stop and with your instructor verify you have created created four (4) 5 GB LUNs with a LUN ID range starting with the RG10 LUN ID. If the LUNs you created do not match the settings specified, with instructor assistance correct the settings before proceeding. Subsequent lab exercises depend upon the LUNs created to be as specified.

EMC Educational Services

71

Step 3

Action Create LUN Folder for RG5 LUNs:  Select the Folders tab in the LUNs page.  Click Create and in the Name field enter your RG5 LUN Folder name. This folder will hold all of your RAID Group 5 LUNS. Click OK, Yes, and OK to complete the operation.  Once created, select your RG5 LUN Folder and click Properties. Then select the LUNs tab.  From the Available LUNs window, expand the tree for SPA and SPB. Locate and select your six previously created RG5 LUN Names and click Add to move them to the Selected LUNs window. Then click OK, Yes, and OK to complete the operation.

4

Create LUN Folder for RG10 LUNs:  Select the Folders tab in the LUNs page.  Click Create and in the Name field enter your RG10 LUN Folder name. This folder will hold all of your RAID Group 10 LUNS. Click OK, Yes, and OK to complete the operation.  Once created, select your RG10 LUN Folder and click Properties. Then select the LUNs tab.  From the Available LUNs window, expand the tree for SPA and SPB. Locate and select your four previously created RG10 LUN Names and click Add to move them to the Selected LUNs window. Then click OK, Yes, and OK to complete the operation.

End of Lab Exercise Part 3

EMC Educational Services

72

Lab: Part 4 – Create Thick and Thin LUNs Step 1

Action Create Thick LUNs on the Block Pool:  Navigate to Storage > LUNs  From the LUNs tab click Create  Create LUNs in the General tab with the following settings: Storage Pool Type: Pool RAID Type: Mixed: Multi-tiered with mixed RAID types Storage Pool for new LUN: Block Pool Thin: UNCHECKED User Capacity: 5 GB LUN ID: Thick LUN ID Number of LUNS: 4 Select the Name radio button. In the Name field enter your Thick LUN Name Starting ID: Thick LUN ID  Select the Advanced tab and configure the following settings: Set Default Owner: Auto Tiering Policy: Start High then Auto-Tier (Recommended) Snapshot Auto-delete Policy: unchecked Note: The Thin checkbox is unchecked so the LUNs you are creating will be Thick LUNs.  Click Apply, Yes and OK to complete the operation. Please stop and with your instructor verify you have created four (4) 5 GB Thick LUNs with a LUN ID range starting with the Thick LUN ID. If the LUNs you created do not match the settings specified, with instructor assistance correct the settings before proceeding. Subsequent lab exercises depend upon the LUNs created to be as specified.

EMC Educational Services

73

Step 2

Action Create Thin LUNs on the Block Pool:  Create LUNs in the General tab with the following settings: Storage Pool Type: Pool RAID Type: Mixed: Multi-tiered with mixed RAID types Storage Pool for new LUN: Block Pool Thin: CHECKED User Capacity: 10 GB LUN ID: Thin LUN ID Number of LUNS: 4 Select the Name radio button. In the Name field enter your Thin LUN Name Starting ID: Thin LUN ID  Select the Advanced tab and configure the following settings: Set Default Owner: Auto Tiering Policy: Start High then Auto-Tier (Recommended) Snapshot Auto-delete Policy: unchecked  Click Apply, Yes and OK to complete the operation. Please stop and with your instructor verify you have created four (4) 10 GB Thin LUNs with a LUN ID range starting with the Thin LUN ID. If the LUNs you created do not match the settings specified, with instructor assistance correct the settings before proceeding. Subsequent lab exercises depend upon the LUNs created to be as specified.

EMC Educational Services

74

Step 3

Action LUN Properties:  Navigate to Storage > Storage Configuration > Storage Pools and select the Pools tab.  Select the Block Pool and click the Properties button.  Select the General tab. How much physical capacity has been allocated on the Pool? _________________________  Click the Cancel button to close the properties page.  From the Pools tab select the Block Pool. From the Details section, select the LUNs tab. From the Usage drop-down list, select ALL User LUNs.

 Select one of your Thick LUN Names and click the Properties button. Record the details listed from the General tab in the LUN Capacity section. ________________________________________________________________

EMC Educational Services

75

Step

Action  Click the Cancel button to close the properties window.  Select one of your Thin LUN Names and click the Properties button. Record the details listed from the General tab in the LUN Capacity section. _______________________________________________________________

Note: User Capacity is the size of the LUN that is presented to the host. Consumed Capacity is user capacity to which the host has written data. Thin LUN consumed capacity and rate of consumption can vary depending on the attached host file system or application using the LUN. This is a normal condition typical of most thin provisioning services.  Click the Cancel button to close the properties window. 4

Create LUN Folder:  Navigate to Storage > LUNs and select the Folders tab.  Click Create and in the Name field enter your Pool LUN Folder name. This folder will hold all of your thick and thin pool LUNs. Click OK, Yes, and OK to complete the operation.  Select your Block Pool folder and click the Properties button. From the properties window select the LUNs tab.  From the Available LUNs window, expand the tree for SPA and SPB. Locate and select your four previously created Thick LUN Names, the four previously created Thin LUN Names, and click Add to move them to the Selected LUNs window. Then click OK, Yes, and OK to complete the operation.  Verify that a total of eight (8) LUNs are in your Pool LUN Folder.

End of Lab Exercise Part 4

EMC Educational Services

76

Lab: Part 5 – Verify Hot Spare Policy Step 1

Action Hot Spare Policy: VNX systems use unused, or unbound, disks as hot spares. The table below displays the number of unused disks that is recommended in order to accommodate a hot spare. SAS FLASH SAS

Recommended 1 unused disk per 30 Disks

NL-SAS 2

Verify spare policy and unused disks:  While still logged on to Unisphere, navigate to System > Hardware > Hot Spare Policy Here you will find a list of all the disk types available for your VNX system, and the policy set for each disk type. A Recommended policy adheres to the EMC best practices policy for that disk type/size. Custom policy gives the administrator an option for their own ratio in the box in the Keep Unused per Policy column. The No Hot Spares policy does not reserve any hot spares. According to the number of disks in your VNX, how many unused disks are recommended per disk type? SAS Flash ______

SAS_______

NL-SAS________

 Close all open windows and application on your Student Desktop system.

End of Lab Exercise

EMC Educational Services

77

This page intentionally left blank

EMC Educational Services

78

Lab Exercise: Verifying Windows Host Software and Configuring Host Access to VNX LUN Purpose:

In this lab, you will verify host software already installed on your Windows host and create a VNX storage group in order to provide storage to your Windows host.

Tasks:

In this lab exercise, you will perform the following tasks:    

EMC Educational Services

Verify Host Configurations - iSCSI Initiators, PowerPath version, host agent, and Secure CLI Verifying that the VNX Array is configured to AutoManage hosts Create a VNX storage group and add LUNs to the storage group Configure Windows host access to LUNs

79

Preparing for the Lab Please refer to your Class Configuration Sheet for this lab and record the values for each item listed. You will use these values for the lab exercise.

Student number:

__________________________________________________

VNX:

__________________________________________________

VNX Address (Control Station):

__________________________________________________

VNX Address (SPA):

__________________________________________________

VNX Address (SPB):

__________________________________________________

Windows host:

__________________________________________________

Windows host Address:

__________________________________________________

Windows Storage Group:

__________________________________________________

Pool LUN Folder:

__________________________________________________

Thick LUNs:

__________________________________________________

Thin LUNs:

__________________________________________________

EMC Educational Services

80

Lab: Part 1 – Verify Windows Host Software Step 1

Action System Login:  (If you are not already logged in to your “Student Desktop”) Connect to your “Student Desktop” via your VDC connection.  From your Student Desktop system, launch the RDP Plus application that is available from the Desktop view or its taskbar.

 Connect to your Windows host according to the following information: Computer(s): Enter your Windows host User: Administrator Password: emc2Local!  Click Connect.

EMC Educational Services

81

Step 2

Action Verify Powerpath version and secure CLI installation:  On your Windows host, open a Command window which is available from the Desktop view or its task bar.

 In the command window run the following command: powermt version What is the Powerpath version running on your Windows host? ___________________  To verify that secure CLI is installed on your host, enter naviseccli at the command prompt. This should return a “not enough arguments” message, which proves that secure CLI has been installed.  Close the command prompt.

EMC Educational Services

82

Step 3

Action Verify host agent installation and iSCSI initiator:  On your Windows host, open the Services tool which is available from the Desktop view or its task bar.

 Verify that the host agent and the iSCSI initiator services are up and running. Look for “Navisphere_Agent”, which is the host agent service, and the Microsoft iSCSI Initiator service.

 Close the Services window.  Right-click the Internet connection icon on the bottom right corner of your Windows host and select Open Network and Sharing Center.

 The host has two networks in the Active Connection list. The “Unidentified network” is a non-routed network that connects to the configured iSCSI ports of your VNX.  Close the Network and Sharing Center.  Leave your RDP Plus session to your Windows host open on your Student Desktop system. You will return to the session in a later part of the lab exercise.

End of Lab Exercise Part 1

EMC Educational Services

83

Lab: Part 2 – Verify the VNX Array is configured to Auto-Manage hosts Ste p 1

Action

VNX SP setup page login:  From your Student Desktop system, open a browser and enter the VNX Address (SPA) followed by . Example: 192.168.1.31/setup  The browser displays a certificate warning message. Select the Continue to this website… option.  To login, enter the sysadmin/sysadmin credentials and select the Scope: Unisphere.

2

Verify Automanage:  In the Setup display scroll down until you find the Turn Automanage On/Off button. Click it to enter the settings.

 Confirm that Automatic Server Discovery is enabled.

What does this setting do? _________________________________________________________________  Close your browser windows.

End of Lab Exercise Part 2

EMC Educational Services

84

Lab: Part 3 – Create and Populate Storage Groups with EMC Unisphere -Windows Step 1

Action System Login:  From your Student Desktop, open a browser and login to Unisphere on your assigned VNX using the VNX Address (Control Station) and the user credentials: sysadmin/sysadmin with Scope Global selected.

2

Verify Storage Groups are Enabled:  From the navigation bar drop-down list, select your VNX.  From the navigation bar select System. From the right-side Tasks pane “System Management” section click the System Properties link.  In the Configuration section, verify that the Storage Group option checkbox is checked. This option enables storage group capability for the selected storage system. This option cannot be disabled, so the check box appears dimmed and is unavailable when Storage Groups is enabled.  Close the window

3

Create a Storage Group:  Navigate to Hosts > Storage Groups.  Create a new Storage Group by clicking Create. Create the storage group according to the following information: Storage Group Name: Windows Storage Group Reminder: Storage Group names are case sensitive.  Click OK.  Click Yes to the message “Do you wish to add LUNs or connect host”

EMC Educational Services

85

Step 4

Action Add LUNs and Hosts to the Storage Group:  Click the LUNs tab. From the Available LUNs window, expand your Pool LUN Folder, locate the two Thick LUNs and the two Thin LUNs and add them to your Windows Storage Group.  Click the Host tab, select your Windows host from the Available Hosts pane and click the  to move the hosts to the Hosts to be Connected pane.  Click OK, Yes, OK. Please stop and with your instructor verify you have selected and added the correct Thick LUNs and Thin LUNs to your Windows Storage Group. If the LUNs added are not the correct LUNs specified, with instructor assistance correct the configuration before proceeding Subsequent lab exercises depend upon the specified LUNs being given to the host.

5

Verify Storage Group Creation:  From theright-side task pane in the Host Management section, click the Update All Hosts link.  Select your VNX Storage System and click Poll. Click Yes. After the Status reads Success followed by the current date and time click Cancel.  From the Storage Group window select your Windows Storage Group.  From the Details section click the Hosts tab and verify that your Windows host is connected.  From the Details section click the LUNs tab and verify that LUNs are displayed.

End of Lab Exercise Part 3

EMC Educational Services

86

Lab: Part 4 – Configure Windows Host Access to LUNs Step 1

Action System Login:  On your Student Desktop system, return to your open RDP Plus session to your Windows host.

2

Bring disks Online:  Click the Server Manager icon on the taskbar of your Windows host.  From the Server Manager window, expand the File and Storage Services container on the left-side panel and select Disks. The DISKS pane in most cases will show four (4) DGC LUNZ disks. The VNX by default presents LUNZ disks to the host when no LUNs are presented to the host. This is to provide basic SCSI connectivity from the host to the array. Now that LUNs are presented to the host, the host must rescan to see the newly presented LUNs.  Click the TASKS drop down menu and select Rescan Storage. The DISKS pane should show two 5.00 GB disks and two 10.0 GB disks with Status Offline. These are the Thick LUNs and Thin LUNs that were added to the Windows Storage Group.

 Right-click each one of the offline disks and select the Bring Online option. The disk status may not change immediately; you may need to Refresh the disk table from the TASKS drop down menu.

EMC Educational Services

87

Step 3

Action Create New Volume on each disk:  Right-click one of the iSCSI disks and select New Volume.  In the New Volume Wizard, click Next to start the wizard.  Select one of the disks and click Next. Keep the default value for size, but make sure the volume size matches the available capacity.  Keep all other defaults for Drive Letter and File Systems Settings. Click Create.  Repeat the above steps for the other three iSCSI disks. You should now havefour (4) iSCSI disks that are Partitioned and have 0.00 GB in the Unallocated column. You may now close the Server Manager window.

EMC Educational Services

88

Step 4

Action Verify the Volumes are seen by the VNX:  From your Student Desktop Unisphere session, navigate to Hosts and in the right side Tasks pane Host Management section, select Connect Host.  Type in your Windows host Address in the Enter Host IP Address field. Click Go.  In the lower Volumes on Block Storage Systems section, verify that your mount volumes are present.  Click OK to close the window.

 On the Windows host, close all open windows and application.  Disconnect from the Remote Desktop session by accessing the Logoff Session icon which is available from the Windows host Desktop view or its taskbar.

End of Lab Exercise

EMC Educational Services

89

This page intentionally left blank

EMC Educational Services

90

Lab Exercise: Verifying Linux Host Software and Configuring Host Access to VNX LUN Purpose:

In this lab, you will verify host software already installed on your Linux host and create a VNX storage group in order to provide access to the LUNs.

Tasks:

In this lab exercise, you will perform the following tasks:   

EMC Educational Services

Verify Host Configurations - iSCSI Initiators, PowerPath version, host agent, and Secure CLI Create a VNX storage group and add LUNs to the storage group Configure Linux host access to LUNs

91

Preparing for the Lab Please refer to your Class Configuration Sheet for this lab and record the values for each item listed. You will use these values for the lab exercise.

Student number:

__________________________________________________

VNX:

__________________________________________________

VNX Address (Control Station):

__________________________________________________

VNX Address (SPA):

__________________________________________________

VNX Address (SPB):

__________________________________________________

Linux host:

__________________________________________________

Linux host Address:

__________________________________________________

Linux Storage Group:

__________________________________________________

RG5 LUN Folder:

__________________________________________________

RG5 LUNs:

__________________________________________________

EMC Educational Services

92

Lab: Part 1 – Verify Linux Host Software Step 1

Action System Login:  (If you are not already logged in to your “Student Desktop”) Connect to your “Student Desktop” via your VDC connection.  From your Student Desktop system, launch the PuTTY application that is available from the Desktop view or its taskbar.

 Open an SSH session to your Linux host according to the following information; Host Name (or IP address): Enter your Linux host Click Open to open the SSH session login as: root password: emc2Local! 2

Verify Powerpath version and secure CLI installation:  In the open SSH window, run the following command: powermt version What is the Powerpath version running on your Linux host? ___________________  To verify that secure CLI is installed on your host, enter naviseccli at the command prompt. This should return a “not enough arguments” message, which proves that secure CLI has been installed.

EMC Educational Services

93

Step 3

Action Verify host agent status:  Run the following command to change directory: cd /etc/init.d  Run the following command to verify the Host agent is running: ./hostagent status  The Host agent status can also be verified with the following command: ps -ef | grep hostagent  If it’s not running, start the agent with the command: ./hostagent start

4

Validate iSCSI initiator and service status:  Run the following command to change directory: cd /etc/iscsi  To validate the host initiator the command: more initiatorname.iscsi What is the name of the initiator that was returned?_________________________________  To verify iSCSI service status, run the command: service iscsi status  If not started, start the service by the command: service iscsi start

End of Lab Exercise Part 1

EMC Educational Services

94

Lab: Part 2 – Create and Populate Storage Groups with EMC Unisphere -Linux Step 1

Action System Login:  From your Student Desktop, open a browser and login to Unisphere on your assigned VNX using the VNX Address (Control Station) and the user credentials: sysadmin/sysadmin with Scope Global selected.

2

Validate Linux host initiators:    

3

From the navigation bar drop-down list, select your VNX. Navigate to Hosts > Initiators. In the Filter field enter your Linux host. The Initiator Name field should list the initiator name for your host for each SP port that is connected to. Each initiator should also be listed as Registered and Logged In.

Create a Storage Group:  Navigate to Hosts > Storage Groups.  Create a new Storage Group by clicking Create. Create the storage group according to the following information: Storage Group Name: Linux Storage Group Reminder: Storage Group names are case sensitive.  Click OK.  Click Yes to the message “Do you wish to add LUNs or connect host”

EMC Educational Services

95

Step 4

Action Add LUNs and Hosts to the Storage Group:  Click the LUNs tab. From the Available LUNs window, expand your RG5 LUN Folder, locate and add three RG5 LUNs to your Linux Storage Group.  In the Host LUN ID, enter “50” “51” “52” for the LUNs respectively. The Host IDs are used by the Linux server to see the LUNs. If you leave them blank, default values will be assigned.

 Click the Host tab, select your Linux host from the Available Hosts pane and click the  to move the host to the Hosts to be Connected pane.  Click OK, Yes, OK.  Return to your PuTTY session to the Linux host and reboot the system by running the following command: reboot  A connection error message for you PuTTY session will be displayed. Close it and the orphaned PuTTY session.  The Linux host will reboot in a moment. To verify its reboot, open a Command Prompt on your Student desktop system and issue a ping command to your Linux host. When the host replies to the ping, continue to the next part of the lab.

End of Lab Exercise Part 2

EMC Educational Services

96

Lab: Part 3 – Configure Linux Host Access to LUNs Step 1

Action Run levels for iSCSI Daemon:  Open another PuTTY session to your Linux host.  Run the following commands: chkconfig --list iscsi chkconfig --level 0123456 iscsi on These commands will check and set the run levels for the iSCSI daemon to automatically start at boot and to shut down when the server is brought down.

EMC Educational Services

97

Step 2

Action View PowerPath devices for your Linux host:  From your PuTTY session to your Linux host, run the following command: powermt display dev=all What is the name of the pseudo-device given to each LUN? ________________________________________________________________ ________________________________________________________________ What is the Failover Mode set to? ______________________________________________

EMC Educational Services

98

Step 3

Action Partition the disk and create a file system on the pseudo-device:  The fdisk command will be run next to create disk partitions for the host on the assigned VNX LUNs. The command is menu drive. Run the following command and follow the listed menu options: fdisk /dev/emcpowera A warning message will appear, Type n to continue Create a Primary Partition. Type p For the number of Partitions type 1 For the first cylinder, accept the default of 1 by pressing Enter For the last cylinder, accept the default last cylinder value by pressing Enter Type w to write Table to disk and exit  Next, create a file system on the disk partition by running the following command: mkfs.ext3 /dev/emcpowera1  Create a mount point for the new file system by running the following command: mkdir /mntA1  Optional: You may repeat the same tasks listed here to partition the other two pseudo-devices, emcpowerb and emcpowerc. Use /mntB1 and /mntC1 for the mount points.

EMC Educational Services

99

Step 4

Action Mount and verify the device:  Mount your emcpowera1 device to the newly created mntA1 directory. mount /dev/emcpowera1 /mntA1  If you have partitioned the other two pseudo-devices, you also need to mount them. mount /dev/emcpowerb1 /mntB1 mount /dev/emcpowerc1 /mntC1  Change directory to /mntA1 and write some data using the touch command touch test

You should be able to write data to your Linux file system.  Verify the file was written by running the following command: ls

EMC Educational Services

100

Step 5

Action Verify the Volumes are seen by the VNX:  From your Student Desktop Unisphere session, navigate to Hosts and in the right side Tasks pane Host Management section, select Connect Host.  Type in your Linux host Address in the Enter Host IP Address field. Click Go.  In the lower Volumes on Block Storage Systems section, verify that your mount volumes are present.  Click OK to close the window.  Close your PuTTY session to your Linux host.

End of Lab Exercise

EMC Educational Services

101

This page intentionally left blank

EMC Educational Services

102

Lab Exercise: Configuring Host Access to VNX LUNs - ESXi Purpose:

In this lab, you will create a VNX storage group in order to provide an ESXi server access to LUNs.

Tasks:

In this lab exercise, you will perform the following tasks:  

EMC Educational Services

Create a VNX storage group and add LUNs to the storage group Configure ESXi host access to LUNs

103

Preparing for the Lab Please refer to your Class Configuration Sheet for this lab and record the values for each item listed. You will use these values for the lab exercise.

Student number:

__________________________________________________

VNX:

__________________________________________________

VNX Address (Control Station):

__________________________________________________

VNX Address (SPA):

__________________________________________________

VNX Address (SPB):

__________________________________________________

ESXi host:

__________________________________________________

ESXi host Address:

__________________________________________________

ESXi Storage Group:

__________________________________________________

Pool LUN Folder:

__________________________________________________

Thick LUN:

__________________________________________________

Thin LUN:

__________________________________________________

EMC Educational Services

104

Lab: Part 1 – Create and Populate Storage Groups with EMC Unisphere -ESXi Step 1

Action System Login:  (If you are not already logged in to your “Student Desktop”) Connect to your “Student Desktop” via your VDC connection.  From your Student Desktop, open a browser and login to Unisphere on your assigned VNX using the VNX Address (Control Station) and the user credentials: sysadmin/sysadmin with Scope Global selected.

2

Validate ESXi server initiators:    

3

From the navigation bar drop-down list, select your VNX. Navigate to Hosts > Initiators. In the Filter field enter your ESXi host. The Initiator Name field should list the initiator name for your host for each SP port that is connected to. Each initiator should also be listed as Registered and Logged In.

Create a Storage Group:  Navigate to Hosts > Storage Groups.  Create a new Storage Group by clicking Create. Create the storage group according to the following information: Storage Group Name: ESXi Storage Group Reminder: Storage Group names are case sensitive.  Click OK.  Click Yes to the message “Do you wish to add LUNs or connect host”

EMC Educational Services

105

Step 4

Action Add LUNs and Hosts to the Storage Group:  Click the LUNs tab. From the Available LUNs window, expand your Pool LUN Folder, locate and add the Thick LUN and the Thin LUN to your ESXi Storage Group.  Click the Host tab, select your ESXi host from the Available Hosts pane and click the  to move the hosts to the Hosts to be Connected pane.  Click OK, Yes, OK.

End of Lab Exercise Part 1

EMC Educational Services

106

Lab: Part 2 – Configure ESXi Host Access to LUNs Step 1

Action System Login:  From your Student Desktop system, launch the VMware vSphere Client application that is available from the Desktop view or its taskbar.

 Login using the following settings: IP address / Name: ESXi host Address User name: root Password: emc2Local!  Click Login.  In the Security Warning message click Ignore.  In the VMware Evaluation Notice click OK. 2

Verify VMkernel port is setup for iSCSI:  Navigate to the Configurations tab and select Networking from the Hardware table on the left.  Verify that there is a VMkernel port is setup for iSCSI traffic.

EMC Educational Services

107

Step 3

Action Rescan ESXi server for LUNs:  Next, select Storage Adapters from the Hardware table and right-click iSCSI Software Adapter.  Select Rescan to make the LUNs visible to the ESXi server. Once the Rescan is completed, the LUNs will appear in the Details pane.



Close the vSphere Client.

End of Lab Exercise

EMC Educational Services

108

Lab Exercise: Advanced Storage Concepts Purpose:

In this lab, you will perform VNX advanced LUN operations. It will focus on LUN expansion and LUN Migration.

Tasks:

In this lab exercise, you will perform the following tasks:

EMC Educational Services



Expand a Pool-based Thick LUN



Expand a Pool-based Thin LUN



Expand a Classic LUN



Migrate a LUN

109

Preparing for the Lab Please refer to your Class Configuration Sheet for this lab and record the values for each item listed. You will use these values for the lab exercise.

Student number:

__________________________________________________

VNX:

__________________________________________________

VNX Address (Control Station):

__________________________________________________

VNX Address (SPA):

__________________________________________________

VNX Address (SPB):

__________________________________________________

Windows host:

__________________________________________________

Windows host Address:

__________________________________________________

Windows Storage Group:

__________________________________________________

Pool LUN Folder:

__________________________________________________

Thick LUN:

__________________________________________________

Thin LUN:

__________________________________________________

RG5 Base LUN:

__________________________________________________

Base LUN Name:

__________________________________________________

RG5 Stripe LUN:

__________________________________________________

Source LUN:

__________________________________________________

Destination LUN:

__________________________________________________

EMC Educational Services

110

Lab: Part 1 – Expanding Pool-based LUNs Step 1

Action System Login:  (If you are not already logged in to your “Student Desktop”) Connect to your “Student Desktop” via your VDC connection.  From your Student Desktop, open a browser and login to Unisphere on your assigned VNX using the VNX Address (Control Station) and the user credentials: sysadmin/sysadmin with Scope Global selected.

2

Expand a Thick LUN:  From the navigation bar drop-down list, select your VNX.  Navigate to Storage > LUNs.  From the LUNs window, right-click on your Thick LUN and select Expand. Note: to help locate your LUN, in the Filter field input your Student number.  From the LUN Expand Storage dialog, type in a New User Capacity of 10 (GB) and click OK.  From the LUNs window, verify that your Thick LUN now has a User Capacity of 10 GB.

3

Open Remote Desktop session to Windows host:  From your Student Desktop system, launch the RDP Plus application that is available from the Desktop view or its taskbar.

 Connect to your Windows host according to the following information: Computer(s): Windows host User: Administrator Password: emc2Local!  Click Connect.

EMC Educational Services

111

Step 4

Action Extend the volume onto the expanded LUN size:  On your Windows Server, click on the Server Manager icon.  From the Server Manager window, select File and Storage Services > Volumes > Disks.  Click on Tasks and select Rescan Storage.  In the Server Manager Disks pane, locate the expanded drive; it should display 5 GB in the Unallocated column. Select the disk.  When the disk is selected, the Volumes pane of Server Manager displays the volume associated with the disk. Right click the volume and select Extend Volume.  The Extend Volume dialog opens. In the New Size field, enter the Maximum Size number displayed in the dialog. Click OK.  The volume will extend to the new Maximum Size.

5

Expand a Thin LUN:  From you Student Desktop system Unisphere session, navigate to Storage > LUNs.  From the LUNs window, right-click on your Thin LUN and select Expand. Note: to help locate your LUN, in the Filter field input your Student number.  From the LUN Expand Storage dialog, type in a New User Capacity of 15 (GB) and click OK.  From the LUNs window, verify that your Thin LUN now has a User Capacity of 15 GB.

EMC Educational Services

112

Step 6

Action Extend the volume onto the expanded LUN size:  Access your Remote Desktop session to your Windows host.  From the Server Manager window, select File and Storage Services > Volumes > Disks.  Click on Tasks and select Rescan Storage.  In the Server Manager Disks pane, locate the expanded drive; it should display 5 GB in the Unallocated column. Select the disk.  When the disk is selected, the Volumes pane of Server Manager displays the volume associated with the disk. Right click the volume and select Extend Volume.  The Extend Volume dialog opens. In the New Size field, enter the Maximum Size number displayed in the dialog. Click OK.  The volume will extend to the new Maximum Size.

End of Lab Exercise Part 1

EMC Educational Services

113

Lab: Part 2 – Expanding RAID Group LUNs Step 1

Action Renaming a LUN:  From your Student Desktop system Unisphere session, navigate to Storage > LUNs.  From the LUNs window, right-click on your RG5 Base LUN and select Properties. Note: to help locate your LUN, in the Filter field input your Student number.  From LUNs name, rename the LUN to the Base LUN Name and click OK, Yes and OK to complete the operation.

2

Expand Storage Wizard (Striping):  From the LUNs windows, right-click the Base LUN Name and select Expand.  The Expand Storage Wizard will appear. Click Next.  From the Select Expansion Type window leave the default as Striping and click Next.  From the Select Unused LUNs window select RG5 Stripe LUN and click Next.  From the Specify new LUN Capacity window click the GB and Maximum Capacity buttons and click Next.  From the Specify new LUN Settings window keep the defaults and click Next  From the Summary window, review your configuration and click Finish  From the Results from the LUN Expansion Wizard window, once the operation is shown as successful initiated, click Finish.

3

View the component LUNs:  From the LUNs window, when the expansion completes, the Base LUN Name LUN icon will change to represent a metaLUN.  From the LUNs window, right-click the Base LUN Name and select Show Component LUNs.  Expand the Component 0 container. What LUN IDs were assigned for each component? ___________________________  Click OK to close the window.

EMC Educational Services

114

Step 4

Action Add the MetaLUN to your Windows host:  Navigate to Hosts > Storage Groups.  Select your Windows Storage Group and click Properties.  In the Storage Group Properties window, select LUNs tab and expand the MetaLUNs container.  Locate your Base LUN Name and click Add.  Click OK, Yes and OK to complete the operation.  Access your Remote Desktop session to your Windows host.  From the Server Manager window, select File and Storage Services > Volumes > Disks.  Click on Tasks and select Rescan Storage.  Your disk should appear as Offline. Right click on the drive and select Bring Online.  A message will appear asking if you are sure you want to bring this disk online on the server. Click Yes.  Verify that the drive is Online.  Right click on the drive and select Initialize.  A message will appear asking if you are sure you want to continue. Click Yes.  Right click on the drive and select New Volume.  The New Volume Wizard will appear. Click Next.  For the Specify the Size of the Volume click Next.  For Assign to a drive letter or folder select Drive Letter M and click Next.  For Select file system settings use the defaults.  Review your configuration and click Create.

5

Verify the MetaLUN volume is seen by the VNX:  From your Student Desktop Unisphere session, navigate to Hosts and in the right side Tasks pane Host Management section, select Connect Host.  Type in your Windows host Address in the Enter Host IP Address field. Click Go.  In the lower Volumes on Block Storage Systems section, verify that the volume for the M: drive is present.  Click OK to close the window.

End of Lab Exercise Part 2

EMC Educational Services

115

Lab: Part 3 – Migrating LUNs Step 1

Action Navigate to LUNs:  In Unisphere, navigate to Storage > LUNs. LUN Migration moves data from a source LUN to a destination LUN of the same size or larger within a single storage system. This migration is accomplished without disruption to the applications running on the host. LUNs can be the target or source of LUN migration operations. LUN Migration can enhance performance or increase disk utilization for your changing business needs and applications by allowing the user to change LUN type and characteristics, such as RAID type or size, while their Production volume remains online. LUNs can be moved between pools or to a Classic LUN in another RAID group. This exercise will migrate a RAID Group LUN to a Pool-based thin LUN.

EMC Educational Services

116

Step 2

Action Migrate a LUN:  Locate and select the Source LUN and click Properties. Note: to help locate your LUN, in the Filter field input your Student number.  Fill in the following information: o Unique ID (WWN): __________________ o RAID Type: ________________________ o RAID Group: _______________________ o User Capacity: _____________________ o Current Owner: ____________________  Click Cancel to close the properties window.  Locate and select the Destination LUN and click Properties. Note: to help locate your LUN, in the Filter field input your Student number.  Fill in the following information: o Unique ID (WWN): __________________ o RAID Type: ________________________ o Pool: _____________________________ o User Capacity: _____________________ o Current Owner: ____________________  Click Cancel to close the properties window.  Right-click the Source LUN and select Migrate. This will launch the Start Migration window.  For a Migration Rate select Low.  From the Available Destination LUNs section, expand Thin_LUNs and select the Destination LUN for the destination LUN. Click OK, Yes, Yes, OK.

EMC Educational Services

117

Step 3

Action View Migration:  Select Source LUN and click Properties. Click the Migration tab to view the migration progress.  Can the migration rate be changed while the migration is taking place? _____________  Click Cancel.  Navigate to Storage > LUNs > LUN Folders. Under LUN Folders select the Private LUNs folder.  Is the Destination LUN shown under details? _______________________ o Note: If the migration has completed the LUN will not be shown.

EMC Educational Services

118

4

Successful Migration:  Navigate to Storage > LUNs > Select Source LUN and click Properties.  Select the Migration tab. Set the migration rate to ASAP and click Apply, Yes, OK.  Wait until the migration completes.  Once completed, fill in the following information: o Unique ID (WWN): __________________ o User Capacity: _____________________ o RAID Type: ________________________ o RAID Group: _______________________ o Current Owner: ____________________  Click Cancel.  Compare this information to the Source LUN information you wrote down in step 2 of this exercise.  What changed? _______________________________________________  In the LUNs window search for LUN Destination LUN.  Does LUN Destination LUN still exist? ________________________________________  On the Windows host, close all open windows and application.  Disconnect from the Remote Desktop session by accessing the Logoff Session icon which is available from the Windows host Desktop view or its taskbar.

End of Lab Exercise

EMC Educational Services

119

This page intentionally left blank

EMC Educational Services

120

Lab Exercise: SnapView Snapshots Purpose:

To learn the skills for configuring a SnapView environment. Create SnapView snapshots and sessions to demonstrate SnapView use to Windows hosts. Perform a rollback of a snap and also create a consistent session containing SnapView snapshots of multiple LUNs. You will be working with two Windows hosts in this lab exercise. One host will be a primary host and the other host is needed to access the SnapView Snapshot.

Tasks:

In this lab exercise, you will perform the following tasks:        

EMC Educational Services

Verify that SnapView is enabled on the VNX Verify that the required LUNs and Storage Groups are present on the VNX Allocate LUNs to the Reserve LUN Pool Create and Test a SnapView snapshot Test Snapview session persistence Rollback a SnapView session Start and test a consistent Snapview session Test the operation of the Reserved LUN Pool

121

Preparing for the Lab Please refer to your Class Configuration Sheet for this lab and record the values for each item listed. You will use these values for the lab exercise.

Student number:

__________________________________________________

VNX:

__________________________________________________

VNX Address (Control Station):

__________________________________________________

VNX Address (SPA):

__________________________________________________

VNX Address (SPB):

__________________________________________________

Windows host:

__________________________________________________

RG10 LUN:

__________________________________________________

Windows Storage Group:

__________________________________________________

RG10 LUN Folder:

__________________________________________________

SnapViewVol:

__________________________________________________

SnapView Snap:

__________________________________________________

SnapView Session:

__________________________________________________

Peer Storage Group:

__________________________________________________

Peer Windows host:

__________________________________________________

SnapView Session 2:

__________________________________________________

SnapView Session_R:

__________________________________________________

RG10 LUN CS1:

__________________________________________________

SnapView CS1:

__________________________________________________

RG10 LUN CS2:

__________________________________________________

SnapView CS2:

__________________________________________________

Consistent Session:

__________________________________________________

EMC Educational Services

122

Lab: Part 1 – Verify the Reserved LUN Pool Step 1

Action System Login:  (If you are not already logged in to your “Student Desktop”) Connect to your “Student Desktop” via your VDC connection.  From your Student Desktop, open a browser and login to Unisphere on your assigned VNX using the VNX Address (Control Station) and the user credentials: sysadmin/sysadmin with Scope Global selected.

2

Verify that SnapView is licensed:  From the navigation bar drop-down list, select your VNX.  From the navigation bar select System.  From the right-side Tasks Pane in the System Management section, click the System Properties link.  Click the Software tab on the Storage System Properties dialog.  The dialog displays a list of the licensed products. Verify that the following entry appears (note the dash in front of the name): o -SnapView  If the entry is present, then the SnapView software is ready to be used. If the entry is not present, consult the instructor.  Click Cancel

3

Verify free Reserved LUN Pool LUNs:  Navigate to Data Protection > Reserved LUN Pool and select the Free LUNs tab.  The Reserved LUN Pool has already been configured. The LUNs free are RLP_LUN_2010 through RLP_LUN_2041  Select one of the RLP LUNs and click Properties.  Click Ok once you have answered the question below.  Which LUN Folder contains the RLP LUNs? ________________

End of Lab Exercise Part 1

EMC Educational Services

123

Lab: Part 2 – Create a SnapView Snapshot Step 1

Action Add LUN to the Storage Group:  Navigate to Hosts > Storage Groups. Select your Windows Storage Group and click Properties.  Click the LUNs tab. From the Available LUNs window, expand your RG10 LUNs Folder, locate and add the RG10 LUN to your Windows Storage Group.  Click OK, Yes, OK.

2

Access Remote Desktop of Windows host::  From your Student Desktop system, launch the RDP Plus application that is available from the Desktop view or its taskbar.

 Connect to your Windows host according to the following information: Computer(s): Enter your Windows host User: Administrator Password: emc2Local!  Click Connect.

EMC Educational Services

124

Step 3

Action Bring disk Online:  Click the Server Manager icon on the taskbar of your Windows host.  From the Server Manager window, expand the File and Storage Services container on the left-side panel and select Disks.  Click on Tasks and select Rescan Storage.  Disks that were previously allocated to the host will still be present.  Your disk should appear as “Offline”. Right click on the drive and select “Bring Online”.  A message will appear asking if you are sure you want to bring the disk online on the server. Click Yes.  Verify that the drive is now “Online”.

4

Initialize Disk:  Right click on the drive and select “Initialize”.  A message will appear asking if you are sure that you want to continue. Click Yes.

5

Create a new Simple Volume named SnapViewLUN:      

Right click on the drive and select “New Volume”. The New Volume Wizard will appear. Click Next. For the Select the server and disk click Next. For the Specify the Size of the Volume click Next. For Assign to a drive letter or folder use the default and click Next. For Select file system settings enter the name SnapViewVol in the Volume label field.  Review your configuration and click Create. What is the drive letter for the new simple volume you just created?_____________________  Close Server Manager.

EMC Educational Services

125

Step 6

Action Create a folder and a text file on the new volume:  Open File Explorer from the taskbar. In File Explorer click the Computer icon.  Open your SnapViewVol volume, right click the empty space and select New > Folder.  Name the folder SnapView.  Open the SnapView folder.  Right click the empty space and select New > Text Document.  Name the file SnapView.txt.  Open SnapView.txt file and add some text into the file, such as your student number, date and time and save it.

7

Create a SnapView Snapshot:  From your Student Desktop system, in your Unisphere session, navigate to Storage > LUNs.  From the LUNs section, right click the RG10 LUN and select SnapView > Create Snapshot.  Name the Snapshot SnapView Snap.  Do not assign the Snapshot to the Storage Group.  Click OK, Yes, OK.

8

View Snapshot Source LUNs:  Navigate to Data Protection > Snapshots> LUN Snapshots.  No VNX Snapshots have been created at this point; click OK to acknowledge any message that appears  Select the SnapView Snapshots tab.  Click the Source LUNs tab. Select the RG10 LUN.  In the Snapshot Details pane you will see that the state of SnapView Snap is Inactive.

EMC Educational Services

126

Step 9

Action Start a SnapView Session:      

10

Select the Source LUNs tab Right-click the RG10 LUN and select SnapView > Start SnapView Session Name the session SnapView Session. Leave all other parameters at their default values. Click OK, Yes, OK. Click the Sessions tab. The SnapView Session will be present.

Activate the Snapshot for the session:  Click the Snapshot LUNs tab and select SnapView Snap. Click Activate.  Select SnapView Session from the Available Snapshot Sessions pane and click OK, Yes, OK.  Navigate to Data Protection > Reserved LUN Pool. Under the Allocated LUNs tab expand RG10 LUN. Which Reserved LUN is in the RG10 LUN container? ________________________________  Select the Reserved LUN and click Pool Properties. What is the current Usage? ___________________________________________________  Click OK.

11

Delete the text file from your SnapViewVol volume:  Access your existing RDP Plus session to your Windows host.  On your Windows host, launch File Explorer which is available from the Desktop view or its taskbar.  Open the SnapViewVol drive.  Delete the SnapView.txt file you previously created.

EMC Educational Services

127

Step 12

Action Add snapshot to your peer (Secondary) Windows Host Storage Group:  In Unisphere, click Hosts > Storage Groups from the navigation bar.  From the Storage Groups window locate your Peer Storage Group.  If the Peer Storage Group is not present, click Create to create it, adding your Peer Windows host to it.  Click Properties.  Select the LUNs tab on the Storage Group Properties dialog.  Expand the SnapView Snaps container, select SnapView Snap and click Add. Then click OK, Yes, OK.

13

Navigate to the Server Manager menu on your peer (Secondary) Windows host and verify Snapshot:  From your Student Desktop system, launch the RDP Plus application that is available from the Desktop view or its taskbar.  Connect to your Peer Windows host according to the following information: Computer(s): Enter your Peer Windows host User: Administrator Password: emc2Local!  Click Connect.  On the peer Windows Server, click on the Server Manager icon.  From the Server Manager window, select File and Storage Services > Volumes > Disks.  Click on Tasks and select Rescan Storage.  Disks that were previously allocated to the host may still be present.  Your disk should appear as “Offline”. Right click on the drive and select “Bring Online”.  A message will appear asking if you are sure you want to bring this disk online on the server. Click Yes.  Verify that the drive is “Online”.  When the scan is complete, select your disk and verify that the drive letter is present below in the volume section. If no, assign one.  Open the File Explorer and select the SnapViewVol drive. You should see the SnapView.txt file you deleted on your primary Windows host.  Close Server Manager.

EMC Educational Services

128

Step 14

Action Create a text file on the Snapshot:  From your Peer Windows host, open your SnapViewVol (Snapshot) volume, right click the empty space and select New > Folder. Name the folder SnapView_Snapshot.  Open the SnapView_Snapshot folder.  Right click the empty space and select New > Text Document.  Name the file SnapView_Snapshot_file.txt.  Open SnapView_Snapshot_file.txt and add some text into the file, such as your student number, date and time and save it.

15

Verify that no changes have been made to the source Volume:  From your Student Desktop system, access your existing RDP session to your Windows host.  Open the File Explorer and select and open the SnapViewVol volume.  Verify that the text file that was created on the Snapshot is not present on the source volume.

End of Lab Exercise Part 2

EMC Educational Services

129

Lab: Part 3 - Test Persistence of a SnapView Session

Step 1

Action Trespass LUNs:  From you Student Desktop system, in the Unisphere session, navigate to Data Protection > Snapshots > LUN Snapshots. Click OK to clear any message that appears.  Click the SnapView Snapshots tab, and then click the Source LUNs tab.  Right click RG10 LUN, and choose Trespass. Click Yes, OK.

2

Check to see if the session survived the LUN trespass:  Click the refresh icon in the upper right hand corner of the pane.  Select the source LUN, and click the Properties button. The LUN has been trespassed if the Current Owner and Default Owner are different SPs. Click Cancel to close the dialog.  Click the Sessions tab and verify the state of SnapView Session. Did SnapView Session survive the trespass? Why or why not? ________________________

3

Look for a trespass event in the SPA Event Log:  Navigate to System > Monitoring and Alerts > SP Event Logs and select Show SPA Event Log. Click Yes to dismiss any informational dialog that appears. Does the SP event log have a record for the trespass? _________________________________  Click Cancel to close the SPA Events dialog.

End of Lab Exercise Part 3

EMC Educational Services

130

Lab: Part 4 - Test the SnapView Rollback Feature

Step 1

Action Create a second Snapview Session:  In Unisphere, navigate to Data Protection > Snapshots > LUN Snapshots. Click OK to dismiss any informational dialog that appears.  Click the SnapView Snapshots tab, and then click the Source LUNs tab.  Right-click RG10 LUN and click Snapview > Start Snapview Session. Name the new session SnapView Session 2 and click OK, Yes, OK.  Expand RG10 LUN. It should now be populated with two sessions: o SnapView Session 2 o SnapView Session (created previously)

2

Create a text file on the source Volume:  From the existing RDP session to your Windows host, open File Explorer.  Open your SnapViewVol volume, right click the empty space and select New > Folder.  Name the folder SnapView2.  Open the SnapView2 folder.  Right click the empty space and select New > Text Document.  Name the file SnapView2.txt.  Open SnapView2.txt and add some text into the file, such as your student number, date and time and save it. Close the file and close File Explorer.

3

Using Admsnap:  Open the Command Prompt on your Windows host.  Change to the directory containing admsnap by typing the following: o cd \Program Files \EMC\Unisphere Server Utility\  Type the following command: o admsnap_win2k12.exe clone_deactivate –o :  The command should look similar to this when finished: C:\Program Files \EMC\Unisphere Server Utility\admsnap_win2k12.exe clone_deactivate –o E:

EMC Educational Services

131

Step 4

Action

Rollback the session:  From your Student Desktop, in the Unisphere session, click the Source LUNs tab. Select SnapView Session and select Rollback.  In the Start Rollback dialog, under SnapView Recovery Session, check the Start Session box and for Session Name type SnapView Session_R. For the Rollback Rate select High. Click OK, Yes, Yes, OK.

5

Re-activate the Source Volume:  From the existing RDP session to your Windows host, open a Command Prompt.  Change to the directory that contains admsnap  Type the following command: o admsnap_win2k12.exe clone_activate  The command should look something like this when finished: C:\Program Files \EMC\Unisphere Server Utility\admsnap_win2k12.exe clone_activate  Wait for the Rollback process to complete.

6

Verify Rollback Process:  From the Server Manager window on your Windows host, select File and Storage Services > Volumes > Disks.  Click on Tasks and select Rescan Storage.  Disks that were previously allocated to the host may still be present.  Close Server Manager.  Open the File Explorer. Open the SnapViewVol volume. The file SnapView2.txt should not be present. Which file(s) is/are present on the drive? Why? _________________________________

End of Lab Exercise Part 4

EMC Educational Services

132

Lab: Part 5 - Start and Test a Consistent SnapView Session Step 1

Action Create SnapView snapshot of RG10 LUN CS1:     

2

Create SnapView snapshot of RG10 LUN CS2:    

3

In Unisphere, navigate to Storage > LUNs > LUNs. Right-click RG10 LUN CS1 and select SnapView > Create Snapshot. Name the Snapshot SnapView CS1. Do not assign the Snapshot to a Storage Group. Click OK, Yes, OK.

Right-click RG10 LUN CS2 and select SnapView > Create Snapshot. Name the Snapshot SnapView CS2. Do not assign the Snapshot to a Storage Group. Click OK, Yes, OK.

Start a Consistent session:  Navigate to Data Protection > Snapshots > LUN Snapshots and click the SnapView Snapshots tab, and then select the Source LUNs tab. Clear any informational dialog by clicking OK.  Right-click RG10 LUN CS1 and select SnapView > Start SnapView Session.  Name the session Consistent Session and check the Consistent checkbox.  Expand containers SPA and SPB and select RG10 LUN CS2 and click Add. Then click OK, Yes, OK.

4

Activate Snapshot SnapView CS1:  Click the Snapshot LUNs tab. Select SnapView CS1 and click Activate.  From the Available Sessions pane select Consistent Session and click OK, Yes, OK.

5

Activate Snapshot SnapView CS2:  Click the Snapshot LUNs tab. Select SnapView CS2 and click Activate.  From the Available Sessions pane select Consistent Session and click OK, Yes, OK.

EMC Educational Services

133

Step 6

Action Verify Consistent Session:    

7

Click the Sessions tab. Select the Consisent Session and click Properties. Verify the Mode(s) are Persistent, Consistent. In the Member LUNs list, verify that Source LUNs RG10 LUN CS1 and RG10 LUN CS2 are present. Click OK.

Close applications:  Close all applications and open windows on the RDP sessions to your host systems.  Disconnect your RDP sessions to your Windows host systems

End of Lab Exercise

EMC Educational Services

134

Lab Exercise: SnapView Clones Purpose:

To learn the skills for configuring SnapView Clones. Allocate Clone Private LUNs for creating Clones. Create Clone Groups and clone a source LUN. Fracture the clone to demonstrate SnapView Clone use to Windows hosts. You will be working with two Windows hosts in this lab exercise. One host will be a primary host and the other host is needed to access the SnapView Snapshot.

Tasks:

EMC Educational Services

Students perform the following tasks: 

Allocate Clone Private LUNs and enable protected restore



Create and test a Clone using Unisphere



Perform a Clone consistent fracture

135

Preparing for the Lab Please refer to your Class Configuration Sheet for this lab and record the values for each item listed. You will use these values for the lab exercise.

Student number:

__________________________________________________

VNX:

__________________________________________________

VNX Address (Control Station):

__________________________________________________

VNX Address (SPA):

__________________________________________________

VNX Address (SPB):

__________________________________________________

Windows host:

__________________________________________________

Thin LUN ID:

__________________________________________________

Thin LUN Name:

__________________________________________________

Clone Group 1:

__________________________________________________

Pool LUN Folder:

__________________________________________________

Source LUN 1:

__________________________________________________

Clone LUN1:

__________________________________________________

Peer Windows host:

__________________________________________________

Peer host Storage Group:

__________________________________________________

Clone Group 2:

__________________________________________________

Windows Storage Group:

__________________________________________________

Source LUN 2:

__________________________________________________

Clone LUN 2:

__________________________________________________

EMC Educational Services

136

Lab: Part 1 –Clone Private LUNs and Enable Protected Restore Step 1

Action System Login:  (If you are not already logged in to your “Student Desktop”) Connect to your “Student Desktop” via your VDC connection.  From your Student Desktop, open a browser and login to Unisphere on your assigned VNX using the VNX Address (Control Station) and the user credentials: sysadmin/sysadmin with Scope Global selected.

2

Verify that Clone Private LUNs are configured on your VNX system:  From the navigation bar drop-down list, select your VNX.  Navigate to Data Protection > Clones.  From the Protection menu on the right side of the screen, select Configure Clone Settings.  The Clone Private LUNs CPL_LUN_2042 and CLP_LUN_2043 have already been configured and are located here in the Clone Private LUNs section.  Verify that the Protected Restore checkbox is enabled. If not, check it.  Click Cancel once you have answered the question below. What is the capacity of the CPLs? ___________________________________

End of Lab Exercise Part 1

EMC Educational Services

137

Lab: Part 2 – Create and Test a Clone Step 1

Action Create Thin LUNs on the Block Pool:  Navigate to Storage > LUNs and Click Create. Create three (3) LUNs in the General tab with the following settings: Storage Pool Type: Pool RAID Type: Mixed: Multi-tiered with mixed RAID types Storage Pool for new LUN: Block Pool Thin: CHECKED User Capacity: 10 GB LUN ID: Thin LUN ID Number of LUNS: 3 Select the Name radio button. In the Name field enter your Thin LUN Name Starting ID: Thin LUN ID  Select the Advanced tab and configure the following settings: Set Default Owner: Auto Tiering Policy: Start High then Auto-Tier (Recommended) Snapshot Auto-delete Policy: unchecked  Click Apply, Yes and OK to complete the operation. Three Thin LUNs are created having ascending IDs starting with the Thin LUN ID.

2

Create a Clone Group:  Navigate to Data Protection > Clones.  From the Protection menu on the right side of the screen, select Create Clone Group.  Name the Clone Group Clone Group 1.  From the LUNs to be Cloned window, expand the Pool LUN Folder and select the Source LUN 1 (this is the thick LUN that was expanded to 10 GB in a previous lab exercise). Click OK, Yes, OK.  The selected LUN will appear under the Source LUNs tab.

EMC Educational Services

138

Step 3

Action Add a Clone LUN to your Clone Group:  Select the Source LUN 1 and select Add Clone.  Expand the SP and Thin LUN containers to view a list of available LUNs (remember only LUNS of the same size are eligible).  Select the Clone LUN 1 and apply the following parameters: Check the Initial Sync Required checkbox (should be checked by default) Check the Use Protected Restore checkbox. Recovery Policy: Automatic Synchronization Rate: High  Click Apply, Yes, Yes, OK, Cancel.

4

Clone Properties:  Click the Clone LUNs tab.  Select the Clone LUN 1 and click Properties. Note the Clone ID ________________________  Click Cancel.

EMC Educational Services

139

Step 5

Action Identify Source LUN Drive letter:  Navigate to Storage > LUNs.  Locate your Source LUN 1. Note: Enter your Student number into the Filter field to help locate the LUN.  In the Host Information column your Windows host Drive letter for the LUN will be displayed. Record the Source LUN 1 Drive letter: ____________________________________

6

Create a text file on the source LUN:  From your Student Desktop system, launch the RDP Plus application that is available from the Desktop view or its taskbar.  Connect to your Windows host according to the following information:

      

EMC Educational Services

Computer(s): Enter your Windows host User: Administrator Password: emc2Local! On your Windows host, launch File Explorer and open the Drive letter recorded from the previous step. Right click the empty space and select New > Folder. Name the folder Clone_1. Open the folder Clone_1. Right click the empty space and select New > Text Document. Name the file Clone_1.txt Open Clone_1.txt and add some text into the file, such as your student number, date and time and save it. Close the file and close File Explorer.

140

Step 7

Action Flush the host buffers:  Open a Command Prompt on your on your Windows host.  Change directories to Admsnap to by typing the following: cd \Program Files\EMC\Unisphere Server Utility\  Flush the Source LUN host buffers by typing the following command: admsnap_win2k12

flush –o :

The command should look similar to the following command. admsnap_win2k12.exe flush –o H: 8

Fracture Clone:  From your Student Desktop system Unisphere session, navigate to Data Protection > Clones and select the Clone LUNs tab. o Select the Clone LUN 1 and click Fracture, Yes, OK. The Clone state will change to Consistent.  Select the Clone LUN 1 and click Properties. What is displayed after “Is Fractured”? _____________________  Click Cancel

9

Add the Clone to your peer host:  Navigate to Hosts > Storage Groups.  Select your Peer host Storage Group and click Connect LUNs.  Expand the SPA and SPB containers and select the Clone LUN 1 and click Add.  Then click OK, Yes, OK.

EMC Educational Services

141

Step 10

Action Make the Clone visible to the secondary host, and add a text file:  Launch the RDP Plus application and establish an RDP session to your Peer Windows host according to the following information: Computer(s): Enter your Peer Windows host User: Administrator Password: emc2Local!  On your Peer Windows host, click on the Server Manager icon.  From the Server Manager window, select File and Storage Services > Volumes > Disks.  Click on Tasks and select Rescan Storage.  Disks that were previously allocated to the host may still be present.  Your disk should appear as “Offline”. Right click on the drive and select “Bring Online”.  A message will appear asking if you are sure you want to bring this disk online on the server. Click Yes.  Verify that the drive is “Online”. Server Manager will assign a non-conflicting drive letter to the new volume. Record the Drive letter assigned. ____________________________________________  Launch File Explorer and open the drive for the new volume.  Create a new folder named Fractured, and then a new file named Fractured.txt. Add some text into the file, such as your student number, date and time.

EMC Educational Services

142

Step 11

Action Deactivate the Clone from your peer Windows host:  Open the Command Prompt on your peer Windows.  Change to the directory where admsnap is found by typing the following: cd c:\Program Files \EMC\Unisphere Server Utility\  Flush the Source LUN host buffers by typing the following command: admsnap_win2k12

flush –o :

 Deactivate the Clone with admsnap: admsnap_win2k12

clone_deactivate –o :

The drive letter is the drive letter recorded in step 10. 12

Deactivate the source LUN from Windows host:  Access the existing RDP session to your Windows host.  Open the Command Prompt on your Windows host.  Change to the directory where admsnap is found by typing the following: cd c:\Program Files \EMC\Unisphere Server Utility\  Flush the Source LUN host buffers by typing the following command: admsnap_win2k12

flush –o :

The drive letter is the drive letter of the source recorded in step 5.  Deactivate the source LUN with admsnap: admsnap_win2k12

clone_deactivate –o :

The drive letter is the drive letter of the source LUN recorded in step 5. 13

Reverse Synchronize the Clone:  In Unisphere session on your Student Desktop, navigate to Data Protection > Clones.  Then click the Clone LUNs tab.  Select the Clone LUN 1 and click Reverse Synchronize.  Click Yes, OK.

EMC Educational Services

143

Step 14

Action Activate the Volume:  From the existing RDP session to your Windows host, open a Command Prompt.  Change to the directory that contains admsnap  Type the following command: admsnap_win2k12.exe clone_activate  The command should look something like this when finished: C:\Program Files \EMC\Unisphere Server Utility\admsnap_win2k12.exe clone_activate

15

Rescan disks on your Windows host:  From your existing RDP session to your Windows host, access Server Manager.  From the Server Manager window, select File and Storage Services > Volumes > Disks.  Click on Tasks and select Rescan Storage.  Disks that were previously allocated to the host may still be present.  If your disk appears “Offline”, then right click on the drive and select “Bring Online”.  A message will appear asking if you are sure you want to bring this disk online on the server. Click Yes.  Verify that the drive is “Online”.

16

Verify Data on the source LUN:  On your Windows host, open the File Explorer open the Source LUN 1 drive.  Verify that the data on the Source LUN is identical to that on the Clone.

End of Lab Exercise Part 2

EMC Educational Services

144

Lab: Part 3 – Perform a Clone Consistent Fracture Step 1

Action Add second source LUN to Storage Group:  From the Unisphere session on your Student Desktop system, navigate to Hosts >Storage Groups.  Select your Windows Storage Group and click Connect LUNs.  Expand the Thin LUN container, and select Source LUN 2 and click Add. Click OK, Yes, OK.

2

Rescan disks on your Windows host:  Establish an RDP session to your Windows host and access Server Manager.  From the Server Manager window, select File and Storage Services > Volumes > Disks.  Click on Tasks and select Rescan Storage.  Disks that were previously allocated to the host may still be present.  Your disk should appear as “Offline”. Right click on the drive and select “Bring Online”.  A message will appear asking if you are sure you want to bring this disk online on the server. Click Yes. Verify that the drive is “Online”.

3

Create a new Simple Volume:       

EMC Educational Services

Right click on the drive and select “New Volume”. The New Volume Wizard will appear. Click Next. For the Select the server and disk click Next. For the Specify the Size of the Volume click Next. For Assign to a drive letter or folder use the default and click Next. For Select file system settings use the default and click Next. Review your configuration and click Create.

145

Step 4

Action Create a text file on the second source LUN:       

5

On your Windows host, open File Manager. Open the new volume, right click the empty space and select New > Folder. Name the folder Clone_2. Open the folder Clone_2. Right click the empty space and select New > Text Document. Name the file Clone_2.txt Open Clone_2.txt and add some text into the file, such as your student number, date and time and save it.

Create a second Clone Group:  From the existing Unisphere session on your Student Desktop navigate to Data Protection > Clones.  From the Protection menu on the right side of the screen, select Create Clone Group.  Name the Clone Group Clone Group 2.  From the LUNs to be Cloned window, expand the Thin LUNs container and select Source LUN 2. Click OK, Yes, OK.  The Source LUN 2 will appear under the Source LUNs tab.

6

Add a Clone:  Select Source LUN 2 and select Add Clone.  Expand the Thin LUNs container to view a list of available LUNs (remember only LUNS of the same size are eligible).  Select Clone LUN 2 and apply the following parameters: Check the Use Protected Restore checkbox. Recovery Policy: Automatic Synchronization Rate: High  Click Apply, Yes, Yes, OK, Cancel.

7

Synchronize Clone Group 1:  Click the Clone LUNs tab.  Select Clone LUN 1 and click Synchronize.  Click Yes, OK.

EMC Educational Services

146

Step 8

Action Consistently Fracture two Clone Groups:  Click the Clone LUNs tab.  Verify if both Clone Groups Clone Group 1 and Clone Group 2 are synchronized.  Hold the Control key and highlight both Clone Groups Clone Group 1 and Clone Group 2.  Click Fracture, Yes, OK to complete the fracture of the Clone Groups.  Look at the fracture time of each clone from the Properties button. Are the fracture times the same? Why or why not? ____________________________________

End of Lab Exercise

EMC Educational Services

147

This page intentionally left blank

EMC Educational Services

148

Lab Exercise: VNX Snapshots Purpose:

To ensure that the environment is configured correctly for VNX Snapshot. To learn the skills for configuring VNX Snap environment. Create and test VNX Snapshots. Test the Restore feature. Create and test the VNX Snapshot Consistency Group feature. You will be working with two Windows hosts in this lab exercise. One host will be a primary host and the other host is needed to access the SnapView Snapshot.

Tasks:

In this lab exercise, you will perform the following tasks:     

EMC Educational Services

Verify that the VNX Snapshots feature is enabled on the VNX Verify that the required Pool and Pool LUNs are present on the VNX Create and Test a VNX Snapshot Test the VNX Snapshot Restore feature Start and test a VNX Snapshot Consistency Group

149

Preparing for the Lab Please refer to your Class Configuration Sheet for this lab and record the values for each item listed. You will use these values for the lab exercise.

Student number:

__________________________________________________

VNX:

__________________________________________________

VNX Address (Control Station):

__________________________________________________

VNX Address (SPA):

__________________________________________________

VNX Address (SPB):

__________________________________________________

Windows host:

__________________________________________________

Thick LUN ID:

__________________________________________________

Thick LUN Name:

__________________________________________________

Thick LUN:

__________________________________________________

Snapshot Folder:

__________________________________________________

VNX Snapshot:

__________________________________________________

Windows Storage Group:

__________________________________________________

Peer Windows host:

__________________________________________________

VNX Snapshot Copy:

__________________________________________________

CG LUN ID:

__________________________________________________

CG LUN Name:

__________________________________________________

Snap CG:

__________________________________________________

CG LUNs:

__________________________________________________

CG Snapshot:

__________________________________________________

EMC Educational Services

150

Lab: Part 1 – Verify that the VNX Snapshots feature is licensed Step 1

Action System Login:  (If you are not already logged in to your “Student Desktop”) Connect to your “Student Desktop” via your VDC connection.  From your Student Desktop, open a browser and login to Unisphere on your assigned VNX using the VNX Address (Control Station) and the user credentials: sysadmin/sysadmin with Scope Global selected.

2

Verify that the VNX Snapshots feature is licensed:  From the navigation bar drop-down list, select your VNX.  From the navigation bar select System.  From the right-side Tasks Pane in the System Management section, click the System Properties link.  Click the Software tab on the System Properties dialog.  The dialog displays a list of the licensed products. Verify that the following entry appears (note the dash in front of the name): o -VNXSnapshots  If the entry is present, then the VNX Replication Software is ready to be used. If the entry is not present, consult the instructor.  Click Cancel

EMC Educational Services

151

Step 3

Action Create a Thick LUN on the Block Pool:  Navigate to Storage > LUNs and Click Create. Create a LUN in the General tab with the following settings: Storage Pool Type: Pool RAID Type: Mixed: Multi-tiered with mixed RAID types Storage Pool for new LUN: Block Pool Thin: UNCHECKED User Capacity: 10 GB LUN ID: Thick LUN ID Number of LUNS: 1 Select the Name radio button. In the Name field enter your Thick LUN Name  Select the Advanced tab and configure the following settings: Set Default Owner: Auto Tiering Policy: Start High then Auto-Tier (Recommended) Snapshot Auto-delete Policy: unchecked

Click Apply, Yes and OK to complete the operation. One Thick LUN is created.

End of Lab Exercise Part 1

EMC Educational Services

152

Lab: Part 2 - Create a VNX Snapshot with EMC Unisphere Step 1

Action Host disk access preparation:  In Unisphere, navigate to Hosts > Storage Groups.  Select your Windows Storage Group and click Connect LUNs.  From the Selected LUNs section, select all the LUNs you added in previous steps and click the Remove button.  Click OK, Remove LUNs from storage group, OK. This operation removes LUNs previously assigned to the host.

2

Add LUN to your Windows host:  Select your Windows Storage Group and click Connect LUNs  Expand the SPA and SPB containers and locate your newly created Thick LUN and click Add. Click OK, Yes, OK to dismiss the dialog.

3

Scan for new disk on your Windows host:  Establish an RDP session to your Windows host.  On your Windows host, click on the Server Manager icon.  From the Server Manager window, select File and Storage Services > Volumes > Disks.  Click on Tasks and select Rescan Storage.  Your disk should appear as “Offline”. Right click on the drive and select “Bring Online”.  A message will appear asking if you are sure you want to bring this disk online on the server. Click Yes.  Verify that the drive is “Online”.

4

Initialize the new disks:  From the Server Manager Disks pane, right click the new disk and select Initialize.  A message will appear asking if you are sure that you want to continue. Click Yes.

EMC Educational Services

153

Step 5

Action Create New Simple Volume:       

Right click the initialized disk and select “New Volume”. The New Volume Wizard will appear. Click Next. For the Select the server and disk click Next. For the Specify the Size of the Volume click Next. For Assign to a drive letter or folder use the default and click Next. For Select file system settings use the default and click Next. Review your configuration and click Create.

Record the drive letter for the volume. ________________  Close Server Manager 6

Create a folder and a text file on the volume:  In File Explorer open the volume, right click the empty space and select New > Folder.  Name the folder Snapshot Folder.  Open the folder Snapshot Folder.  Right click the empty space and select New > Text Document.  Name the file Snapshot_file.txt.  Open Snapshot_file.txt and add some text into the file, such as your student number, date and time. Save and close the file.

7

Create a VNX Snapshot on the volume:  In Unisphere, navigate to Storage > LUNs.  From the LUNs menu, right click the Thick LUN and select Snapshot > Create Snapshot.  Name the Snapshot VNX Snapshot. In the Description area, enter the Thick LUN to identify the source LUN.  Click OK, OK.

EMC Educational Services

154

Step 8

Action Create a snapshot mount point:          

9

In the Wizards area, click on Snapshot Mount Point Configuration Wizard. Read the Welcome screen and click Next Select your Windows host from the Server List pane and click Next. Select your VNX from the list of storage systems and click Next. In the Available LUNs your Windows Storage Group will be expanded. Select the Thick LUN and click Add. Click Next. Leave the Snapshot Mount Point Name at the default value, and click Next. Select and check your Peer Windows host from the Server List pane and click Next. Review the summary, and click Finish. Read the messages in the Results dialog (they should all show green check marks) and click Finish. Open an RDP session to your Peer Windows host. Verify that the mount point is shown as an uninitialized disk in Server Manager.

Attach the Snapshot to the peer Windows host:     

   

EMC Educational Services

Navigate to Data Protection > Snapshots > LUN Snapshots. Click the Snapshots tab. You should see the Thick LUN. Expand the Thick LUN to view snapshots under the LUN. Select VNX Snapshot, and click the Attach button. Select the Peer Windows host from the Server List pane, and check the Create a copy of point in time snapshot checkbox. Name the copy VNX Snapshot Copy. Click Next. Leave the Attach copy radio button selected, and click Next Review the summary, and click Finish. Read the messages in the Results dialog (they should all show green check marks) and click Finish. The VNX Snapshot Copy should now show Yes under the Modified column, and should also show that it is attached to your Peer Windows host.

155

Step 10

Action Create a file on the VNX Snapshot from your Peer Window host:  Rescan disks on your Peer Windows host.  You should now see a 10 GB disk. Bring the disk online if it is offline.  The disk will have the same data content as primary LUN (Thick LUN). Record the drive letter assigned. ______________________________  Verify that the file Snapshot_file.txt is present on the volume.  Create a new file, name it Snapshot_file_new.txt , and add text to it as before.  Verify that the new file is not present on the primary LUN (on your Windows host).

End of Lab Exercis Part 2

EMC Educational Services

156

Lab: Part 3 - Test the VNX Snapshot Restore Feature

Step 1

Action Flush host buffers on your Peer Windows host, and detach the Snapshot:  From the RDP session to your Peer Windows host, flush the host buffers for the snapshot.  Change to the directory where admsnap is found by typing the following: cd c:\Program Files \EMC\Unisphere Server Utility\  Flush the Source LUN host buffers by typing the following command: admsnap_win2k12

flush –o :

 In Unisphere, select VNX Snapshot copy and click Detach. Leave the Retain… checkbox checked, and click Yes, OK. How has the status of VNX Snapshot copy changed?_________________________________ 2

Take the primary LUN offline, and restore VNX Snapshot copy:  Open a Command Prompt on your Windows host.  Change to the directory where admsnap is found by typing the following: cd c:\Program Files \EMC\Unisphere Server Utility\  Flush the Source LUN host buffers by typing the following command: admsnap_win2k12

flush –o :

 Deactivate the source LUN with admsnap: admsnap_win2k12

clone_deactivate –o :

 In Unisphere, select VNX Snapshot copy and click the Restore button. Click Yes, OK, OK.  Verify that a new VNX Snapshot has been taken of the primary LUN.

EMC Educational Services

157

Step 3

Action Verify that the primary LUN has been restored:  Activate the primary LUN with admsnap: admsnap_win2k12

clone_activate

 Confirm that the primary LUN is visible to your Windows host. It will likely have a different drive letter.  Verify that the primary LUN has the same files as the VNX Snapshot. Why are files Snapshot_file.txt and Snapshot_file_new.txt both present on the source LUN? _______________________________________________________________________

End of Lab Exercise Part 3

EMC Educational Services

158

Lab: Part 4 - Create and Test a VNX Snapshot Consistency Group

Step 1

Action Create Thick LUNs on the Block Pool:  Navigate to Storage > LUNs and Click Create. Create two LUNs in the General tab with the following settings: Storage Pool Type: Pool RAID Type: Mixed: Multi-tiered with mixed RAID types Storage Pool for new LUN: Block Pool Thin: UNCHECKED User Capacity: 10 GB LUN ID: CG LUN ID Number of LUNS: 2 Select the Name radio button. In the Name field enter your CG LUN Name Starting ID: CG LUN ID  Select the Advanced tab and configure the following settings: Set Default Owner: Auto Tiering Policy: Start High then Auto-Tier (Recommended) Snapshot Auto-delete Policy: unchecked  Click Apply, Yes and OK to complete the operation. Two Thick LUNs are created with IDs in ascending order.

2

Add LUNs to the Windows host:  Navigate to Hosts > Storage Groups.  Select your Windows Storage Group and click Connect LUNs  Expand the SPA and SPB containers and locate your newly created CG LUNs and click Add. Click OK, Yes, OK to dismiss the dialog.

EMC Educational Services

159

Step 3

Action Scan for new disk on your Windows host:  Establish an RDP session to your Windows host.  On your Windows host, click on the Server Manager icon.  From the Server Manager window, select File and Storage Services > Volumes > Disks.  Click on Tasks and select Rescan Storage.  Your disks should appear as “Offline”. Right click on each drive and select “Bring Online”.  A message will appear asking if you are sure you want to bring this disk online on the server. Click Yes. Verify that each drive is “Online”.

4

Initialize the new disks:  From the Server Manager Disks pane, right click the new disk and select Initialize.  A message will appear asking if you are sure that you want to continue. Click Yes.

5

Create New Simple Volumes:         

6

Right click one initialized disk and select “New Volume”. The New Volume Wizard will appear. Click Next. For the Select the server and disk click Next. For the Specify the Size of the Volume click Next. For Assign to a drive letter or folder use the default and click Next. For Select file system settings use the default and click Next. Review your configuration and click Create. Repeat the above steps for the second new drive. Close Server Manager

Create data on the new volumes:  Open File Explorer and create text files on each new volume.

EMC Educational Services

160

Step 7

Action Create a Consistency Group with 2 member LUNs:  In Unisphere, navigate to Data Protection > Snapshots > LUN Snapshots. From the right side tree, in the Consistency Group section, click Create Snapshot Consistency Group. Read the Welcome dialog, and click Next.  Name the Consistency Group Snap CG. Add a description if desired, and click Next.  Select the 2 CG LUNs created in the previous step. Click Next.  Read the Summary screen, verify that the information is correct, and click Finish. Read the Results screen, and click Finish if the operation succeeded.

8

Create a VNX Snapshot of the Consistency Group:  Select Snap CG, and click the Create Snapshot button.  Name the snapshot CG Snapshot, and click OK, OK.  Expand Snap CG and verify that the Snapshot has been created. Does the Snapshot have the Modified property set to Yes? Explain the current state of the property. _____________________________________________________________________

9

Attach the Snapshot to the Peer Windows host:  Select CG Snapshot, and click the Attach button.  Select the Peer Windows host, uncheck the checkbox, and click Next, Yes.  Read the Summary screen, and click Finish, then click Finish again after reading the messages. Were you able to successfully perform this operation? Explain why you see the result shown. ________________________________________________________________________

EMC Educational Services

161

Step 10

Action Create a snapshot mount point:         

11

In the Wizards area, click on Snapshot Mount Point Configuration Wizard. Read the Welcome screen and click Next Select your Windows host from the Server List pane and click Next. Select your VNX from the list of storage systems and click Next. In the Available LUNs your Windows Storage Group will be expanded. Select the CG LUNs and click Add. Click Next. Leave the Snapshot Mount Point Name at the default value, and click Next. Select and check your Peer Windows host from the Server List pane and click Next. Review the summary, and click Finish. Read the messages in the Results dialog (they should all show green check marks) and click Finish.

Attach the CG Snapshot to the Peer Windows host:    

Select CG Snapshot, and click the Attach button. Select your Peer Windows host, uncheck the checkbox, and click Next, Yes. Read the Summary screen, and click Finish. Read the Results screen, and click Finish.

Were you able to successfully perform this operation? ______________________ Verify that CG Snapshot now has an entry under the Attached column.

EMC Educational Services

162

Step 12

Action Verify that the Peer Windows host can access the point in time copies:  Rescan disks on your Peer Windows host.  Verify that the 2 Snapshots are visible. Do the Snapshots have the same volume names as the primary LUNs? ____________________ Do the Snapshots have the same drive letters as the primary LUNs? ____________________ Explain your answers. __________________________________________________________

End of Lab Exercise

EMC Educational Services

163

This page intentionally left blank

EMC Educational Services

164

Lab Exercise: Data Mover Network Configuration Purpose:

To acquire the skills and knowledge to be able to configure a VNX system for network access. Note: Screenshots used in this Lab Exercise are meant to be used as examples. You may have different values/data on your VNX system.

Tasks:

In this lab exercise, you will perform the following tasks: 

References:

EMC Educational Services

Configure the VNX for network access

Configuring and Managing Networking on VNX

165

Preparing for the Lab Please refer to your Class Configuration Sheet for this lab and record the values for each item listed. You will use these values for the lab exercise.

Student number:

__________________________________________________

VNX:

__________________________________________________

VNX Address (Control Station):

__________________________________________________

VNX Address (SPA):

__________________________________________________

VNX Address (SPB):

__________________________________________________

Data Mover:

__________________________________________________

Network Device Name:

__________________________________________________

Data Mover Address:

__________________________________________________

Interface Name:

__________________________________________________

Gateway Address:

__________________________________________________

Routed Interface:

__________________________________________________

EMC Educational Services

166

Lab: Part 1 – Configure Networking on VNX Data Movers Step 1

Action System Login:  (If you are not already logged in to your “Student Desktop”) Connect to your “Student Desktop” via your VDC connection.  From your Student Desktop, open a browser and login to Unisphere on your assigned VNX using the VNX Address (Control Station) and the user credentials: sysadmin/sysadmin with Scope Global selected.

2

Verify Data Mover speed and duplex:  From the navigation bar drop-down list, select your VNX.  Navigate to Settings > Network > Settings For File  Select the Devices tab.  Right-click device name of the physical network device and the Data Mover, and select Properties.  Click the arrow on the right side of the “Speed/Duplex” drop-down list and verify it is set to auto. (If it is set to a setting different than “auto”, please ask your instructor before making any modification.)  Click Cancel to close the properties window.

EMC Educational Services

167

Step 3

Action Configure a network interface for the physical network device on the Data Mover:  In the Settings for File window select the Interfaces tab.  Click Create and create a new interface according to the following information: Data Mover: Data Mover Device Name: Network Device Name Address: Data Mover Address Name: Interface Name Netmask: 255.255.255.0 The Broadcast Address is calculated automatically Do not enter the MTU value Do not enter the VLAN ID value  Click OK.

4

Verify default gateway address information The routing entry for the Data Mover default gateway has been preconfigured. In this step you will confirm the address is correct.  From the Settings for File window, select the Routes tab.  Select the Data Mover from the “Show Network Routing for” drop-down menu.  Locate the “0.0.0.0” Network Destination address.  Verify the entry is configured with the Gateway Address and the Routed Interface.

EMC Educational Services

168

Step 5

Action Test remote network access: Test the network interface by pinging the IP address of your DNS server.  From the right-side Task pane, under Network Settings, click the Ping – Data Movers link.

   

From the Data Mover drop-down list, select your Data Mover. From the Interface drop-down list, select your Data Mover Address. In the Destination: field input 192.168.1.50. Click OK.

You should receive a message that includes: “…Response from host: 192.168.1.50 is alive…” This indicates a successful Ping to a remote host – it is the lab DNS server address. If your Ping is not successful, ask your instructor for assistance.

EMC Educational Services

169

Step 6

Action Checking Data Mover DNS configuration:  From the Settings > Network > Settings for File page, select the DNS tab.  From the “Show DNS Domains for:” drop-down menu, select Data Mover. The Data Mover DNS settings have already been configured on your VNX system.  Confirm that the information from the DNS Settings table matches the information below. DNS Domain: hmarine.test Data Mover: Data Mover DNS Servers: 192.168.1.50 Protocol: tcp If the information above does not match what is displayed in Unisphere, ask your instructor for assistance.

End of Lab Exercise

EMC Educational Services

170

Lab Exercise: File System Configuration and Management Purpose:

To acquire the skills and knowledge to be able to create and manage a basic file system. Note: Screenshots used in this Lab Exercise are meant to be used as examples. You may have different values/data on your VNX system.

Tasks:

References:

EMC Educational Services

In this lab exercise, you will perform the following tasks: 

Configure a VNX file system



Extend a file system

Managing Volumes and File Systems with VNX AVM

171

Preparing for the Lab Please refer to your Class Configuration Sheet for this lab and record the values for each item listed. You will use these values for the lab exercise.

Student number:

__________________________________________________

VNX:

__________________________________________________

VNX Address (Control Station):

__________________________________________________

VNX Address (SPA):

__________________________________________________

VNX Address (SPB):

__________________________________________________

Data Mover:

__________________________________________________

File System Name:

__________________________________________________

EMC Educational Services

172

Lab: Part 1 – Configure and Manage a VNX File System Step 1

Action System Login:  (If you are not already logged in to your “Student Desktop”) Connect to your “Student Desktop” via your VDC connection.  From your Student Desktop, open a browser and login to Unisphere on your assigned VNX using the VNX Address (Control Station) and the user credentials: sysadmin/sysadmin with Scope Global selected.

2

Create file system:  From the navigation bar drop-down list, select your VNX.  Navigate to Storage > Storage Configuration > File Systems  Create a file system by clicking the Create button and entering the following information: Create From: Storage Pool File System Name: File System Name Storage Pool: File Pool Storage Capacity: 5 GB Auto Extend Enabled: unchecked Thin Enabled: unchecked Slice Volumes: checked File-level Retention: off Deduplication Enabled: unchecked Vmware VAAI nested clone support: unchecked Data Mover (R/W): Data Mover Mount Point: Default  Click OK.

3

Verify file system mount: Unisphere automatically mounts the file system once it is created if the Default option is selected. Unisphere uses a default mount point that is created with the same name as the file system.  Select the Mounts tab.  Verify that the Path created for your file system is /File System Name.

EMC Educational Services

173

Step 4

Action Analyze file system volume structure: • •

Navigate to Storage> Storage Configuration >Volumes. Filter the volume list for your file system by entering its name

The VNX volume manager, AVM, is used to construct the file system. AVM first creates a stripe volume from five available disk volumes. It then makes a slice volume from the stripe. A metavolume is created from the slice that is used by the file system. Record the meta volume that your file system resides on. _________________________________________________________ Record the slice volume used to create the meta Volume. _________________________________________________________ Record the disk volumes that AVM used to create your stripe volume. _________________________________________________________ 5

Extend a file system:  Navigate to Storage > Storage Configuration > File Systems  Select the file system you just created and click the Extend button.  Extend the file system using the following settings: Extend from: Storage Pool Extend with Storage Pool: File Pool Extend Size: 10 GB  Click OK to complete the operation.

EMC Educational Services

174

Step 6

Action Analyze file system volume structure:  Navigate back to Storage> Storage Configuration >Volumes and filter for your file system once again AVM extends the file system size by creating another slice volume from the existing stripe volume. A new metavolume is created from the new slice. The new metavolume is added to the existing metavolume that the file system is constructed from. Record the name of the new metavolume created. _____________________________________ Record the name of the new slice volume that the new metavolume uses. ______________________________________  Close Unisphere

End of Lab Exercise

EMC Educational Services

175

This page intentionally left blank Lab

EMC Educational Services

176

Exercise: NFS File System Export and Permissions Purpose:

In this lab exercise, you will export a file system and assign root privileges to your Linux host. NOTE: The screenshots used in this Lab Exercise are meant to be used as examples. You may have different values/data on your VNX system.

Tasks:

In this lab exercise, you perform the following tasks:  



References:

EMC Educational Services

Configure Data Movers to mount and export file systems for Linux hosts Configure Data Movers to mount and export a file system at sub directory level (hiding the directories .etc and .lost+found). Assign root permissions to an NFS File system

Configuring NFS on VNX

177

Preparing for the Lab Please refer to your Class Configuration Sheet for this lab and record the values for each item listed. You will use these values for the lab exercise.

Student number:

__________________________________________________

VNX:

__________________________________________________

VNX Address (Control Station):

__________________________________________________

VNX Address (SPA):

__________________________________________________

VNX Address (SPB):

__________________________________________________

Data Mover:

__________________________________________________

Data Mover Address:

__________________________________________________

File System 1:

__________________________________________________

File System 2:

__________________________________________________

Linux Host Address:

__________________________________________________

Peer Linux Host Address:

__________________________________________________

EMC Educational Services

178

Lab: Part 1 – Exporting File Systems for NFS Clients Step 1

Action Login to Unisphere:  (If you are not already logged in to your “Student Desktop”) Connect to your “Student Desktop” via your VDC connection.  From your Student Desktop, open a browser and login to Unisphere on your assigned VNX using the VNX Address (Control Station) and the user credentials: sysadmin/sysadmin with Scope Global selected.

2

Export a file system for the NFS protocol:  From the navigation bar drop-down list, select your VNX.  Navigate to Storage > Shared Folders > NFS  Click Create and enter the following information in the Export window: Choose Data Mover: Data Mover File System: File System 1 Path: /File System 1 Root Hosts: Linux Host address  Click OK. The NFS Exports page displays the exported path of the file system.  Minimize the Unisphere window.

EMC Educational Services

179

Step 3

Action Mount the file system:  From your Student Desktop, use PuTTY to open an SSH to the Linux Host Address.  Log into the host with the following credentials: logon as: root password: emc2Local!  From the terminal window, create a local directory to mount the file system that you have exported via NFS. Type the following: cd / mkdir /fs1

 Check the contents of your /fs1 directory. cd

/fs1

ls –al The directory listing should show that the new directory is empty. In a subsequent lab step the directory will be used as a mountpoint for mounting the top-level of an exported file system from the VNX.  NFS mount this directory to the exported file system on your Data Mover. Type the following: cd / mount Data Mover Address:/File System 1 /fs1 df (confirm that the mount is listed) cd

/fs1

ls –al Note: By default a new directory is empty. Therefore, when you created your /fs1 directory on the client it was empty. However, after NFS mounting it to your Data Mover, /fs1 is now being redirected to a file system showing lost+found and .etc (hidden) directories.

EMC Educational Services

180

Step 4

Action Create user directory on file system  Confirm that you are at /fs1 directory using pwd command. pwd /fs1  List the content of the directory by running the following command: ls – la The directory is no longer empty. When in the directory you are redirected to the remote file system mounted to the directory. Notice that the .etc and lost+found directories are present. These directories are structure present on the top of the VNX file system and should not be disturbed.  Create a new directory and name it engineering. mkdir engineering  Change the permissions on this directory to 775. This means read, write, and execute for the owner and group, and read and execute for others. chmod 775 engineering  Change the owner of engineering directory to epallis. chown -R epallis engineering  Change the group of engineering directory to engprop. chgrp -R engprop engineering  Verify the new permissions on the directory. ls –l drwxrwxr-x. 2 epallis engprop

EMC Educational Services

181

80 Oct 11 14:21 engineering

Step 5

Action Export a file system at sub-directory level:  Go back to your Unisphere session.  Navigate to Storage >Shared Folders > NFS Create NFS and click Create.  Create a new NFS export using the following information: Choose Data Mover: Data Mover Choose File System: File System 1 Path: /File System 1/engineering Read / Write Hosts: Linux Host Address  Click OK.

6

Mount file system at sub-directory level:

 From the SSH session, mount the new file system export following the steps shown below. Remember you should be logged in as root in order to mount a file system. cd / mkdir /engdir (this directory will be used as a mountpoint) mount Data Mover Address:/File System 1/engineering /engdir df ls –l | grep engdir drwxrwxr-x.

2 epallis engprop

80 Oct 11 14:21 engdir

Notice that the permissions on the new directory engdir are the permissions you setup earlier: 775 read, write, and execute for the owner and group. And Read and execute for others.

EMC Educational Services

182

Step 7

Action Test directory permissions -owner:  Using PuTTY, open another SSH session to the Linux Host address and login with the following credentials: login as: epallis password: emc2Admin!  Change directory to engdir. cd /engdir ls –al Can you see the directories .etc and lost+found? _______________ You should not see them because the file system has been exported on the sub-directory level.  Create a new file and name it ownerfile and obtain a listing of the directory. touch ownerfile ls -l Were you able to create a new file? __________________ You should be able to create the new file because epallis is the owner of this directory. From the ls output, who is the file owner? _______________ What group is associated to the file? ____________________

EMC Educational Services

183

Step 8

Action Test directory permissions - group:  Using PuTTY, open another SSH session to the Linux Host address and login with the following credentials: login as: eplace password: emc2Admin!  Change directory to engdir and create a new file. Name it groupfile and obtain a listing of the directory. cd /engdir touch groupfile ls -l Were you able to create a new file? ______________ You should be able to create the new file because eplace belongs to the engprop group which is the directory group. From the ls output, record the owner and group associated to the groupfile. _____________________________________________________________  Using PuTTY, open another SSH session to the Linux Host address and login with the following credentials: login as: swoo password: emc2Admin!  Change directory to engdir. Create a new file and name it swoofile. cd /engdir touch swoofile ls -l Were you able to create a new file? _____________________ Were you able to obtain a listing? ___________________ You should not be able to create the new file because the user swoo is neither the directory owner nor belongs to the engprop group. However, swoo still can read and execute.

EMC Educational Services

184

Step 9

Action Lab cleanup:  Exit the SSH sessions to the Linux Host address for users: swoo, eplace, and epallis by running the exit command. Leave the existing SSH session for the root user open. exit  From the SSH session for the root user, unmount and delete mountpoints. Then exit the SSH session. cd / umount /fs1 umount /engdir rmdir /fs1 rmdir /engdir exit  From Unisphere, unexport the file system by navigating to Storage > Shared Folders > NFS.  Multiple select the /File System 1 and the /File System 1/engineering exports and click the Delete button. Click OK to complete the operation.

10

Lab cleanup – Delete File System:  Navigate to Storage > Storage Configuration > File Systems.  Select File System 1 and click the Delete button.  Click OK to complete the operation. Note: Deleting the file system removes its mountpoint and the associated meta volumes, stripe and slice volumes. This space has been returned to the Storage Pool for re-use.

End of Lab Exercise Part 1

EMC Educational Services

185

Lab: Part 2 – Assigning Root Privileges Step 1

Action Create a new file system: In Unisphere, navigate to Storage > Storage Configuration > File Systems  Click Create and enter the following information: Create From: Storage Pool File System Name: File System 2 Storage Pool: File Pool Storage Capacity: 10 GB Auto Extend Enabled: unchecked Thin Enabled: unchecked Slice Volumes: checked File-level Retention: off Deduplication Enabled: unchecked Vmware VAAI nested clone support: unchecked Data Mover (R/W): Data Mover Mount Point: Default  Click OK.

2

Export the newly created file system with root privileges:  Navigate to Storage > Shared Folders > NFS and click Create.  Enter the following information: Choose Data Mover: Data Mover File System: File System 2 Path: /File System 2 Root Hosts: Linux Host Address  Click OK to complete the operation.

EMC Educational Services

186

Step 3

Action Mount file system:  From your Student Desktop, use PuTTY to open an SSH to the Linux Host Address.  Log into the host with the following credentials: logon as: root password: emc2Local!  From the command prompt, make a local directory to mount the exported file system. Type the following: cd / mkdir /fs2 mount Data Mover Address:/File System 2 /fs2 df

From the df output verify that the VNX File System 2 export is mounted on the Linux host fs2 directory.  Change to the /fs2 directory and create a new directory called student. cd /fs2 mkdir student chmod 777 student cd student echo “THIS IS A TEST” > File

EMC Educational Services

187

Step 4

Action Export the file system at the sub-directory level: Go back to your Unisphere session and export the File System 2 file system at the sub-directory level.  Navigate to Storage > Shared Folder > NFS and click Create. Define the export as follows: Choose data Mover: Data Mover File System: File System 2 Path: /File System 2/student Read-only Hosts Peer Linux Host Address Read/Write Hosts: Linux Host Address  Click Ok to complete the operation.

5

Mount the file system at the sub-directory level:  From your existing PuTTY session to Linux Host Address, create a new directory and mount the NFS export. cd / mkdir /student mount Data Mover Address:/File System 2/student /student

EMC Educational Services

188

Step 6

Action Mount NFS export to a directory in the Peer Linux Host:  From your Student Desktop, open another PuTTY session to the Peer Linux host (Peer Linux Host Address) and login with the Peer Linux Root Credentials.  Create a new directory on the Peer Linux host named Student number. cd / mkdir /Student number  Mount the above directory to the file system that you exported in the previous step. mount Data Mover IP Address:/File System 2/student /Student number df (Confirm that your export is visible)

7

Test root privileges:  Create a user file in Student number of the Peer Linux host cd /Student number touch file Do you have write permissions? _______________ . You should not be able to create a new file because the file system has been exported as read only to this particular host.

8

Unmount the directory and logout from the Peer Linux host: Unmount /Student number and exit from the your PuTTY ssh session to the Peer Linux host. cd / umount /Student number rmdir /Student number exit

EMC Educational Services

189

Step 9

Action Create a user file in the mounted directory in the primary Linux host:  From the PuTTY ssh session to the Linux Host Address create a user file in the student directory. cd /student touch newfile Do you have write permissions? _____________. You should be able to create a new file because the file system has been export as read write to this particular host.

10

Lab Cleanup:  Umount and delete mountpoints and exit from the PuTTY ssh session to the Linux Host (Linux Host Address). cd / umount /student rmdir /student umount /fs2 rmdir /fs2 exit From Unisphere delete the exports for File System 2 by navigating to Storage > Shared Folders > NFS.   

Multiple-select the NFS exports /File System 2 and /File System 2/student and click Delete. Next, navigate to Storage > Storage Configurations > File Systems and delete File System 2. Close Unisphere.

End of Lab Exercise

EMC Educational Services

190

Lab Exercise: VDM Configuration Purpose:

To acquire the skills and knowledge to configure and perform operations on a VNX Virtual Data Mover. The VDM will be implemented with CIFS in a following lab exercise. Note: Screenshots used in this Lab Exercise are meant to be used as examples. You may have different values/data on your VNX system.

Tasks:

In this lab exercise, you will perform the following tasks:      

References:

EMC Educational Services

Configure the VNX with a Virtual Data Mover Unload the VDM Load the VDM to the peer Data Mover Mount a file system to the VDM Move the VDM to the original Data Mover Verify the file system mount status

Configuring Virtual Data Movers on VNX

191

Preparing for the Lab Please refer to your Class Configuration Sheet for this lab and record the values for each item listed. You will use these values for the lab exercise.

Student number:

__________________________________________________

VNX:

__________________________________________________

VNX Address (Control Station):

__________________________________________________

VNX Address (SPA):

__________________________________________________

VNX Address (SPB):

__________________________________________________

Data Mover:

__________________________________________________

Peer Data Mover:

__________________________________________________

VDM:

__________________________________________________

File System:

__________________________________________________

EMC Educational Services

192

Lab: Part 1 – System Setup for VDM Implementation Step 1

Action System Login:  (If you are not already logged in to your “Student Desktop”) Connect to your “Student Desktop” via your VDC connection.  From your Student Desktop, open a browser and login to Unisphere on your assigned VNX using the VNX Address (Control Station) and the user credentials: sysadmin/sysadmin with Scope Global selected.

2

Create a Virtual Data Mover:  From the navigation bar drop-down list, select your VNX.  Navigate to Storage > Shared folders > CIFS and select the VDMs tab.  Click Create to create a new Virtual Data Mover according to the following information: Data Mover: Data Mover Name: VDM Create the configuration using: Default Storage Allocation  Click OK.  Review the information displayed in the “VDMs” tab for your VDM. Confirm it is named correctly, is assigned to your Data Mover and its status is “OK”. If the information is incorrect, select your VDM and click Properties and make the needed corrections. Ask your instructor if you need assistance.

EMC Educational Services

193

Step 3

Action Unload the Virtual Data Mover:  Select your VDM and click Properties. Note: You can use the “Filter” field on the page to help locate your VDM. Input your student number into the field to display your VDM.  From the Data Mover drop-down list select Unloaded.  Click OK.  A confirmation window is displayed about the unload operation. Review the displayed message. Click the details link in the message.  Review the details of the unload operation. Click OK to close the window. 

Click OK in the “Confirm” window to proceed with the unload operation.

 Review the information displayed in the “VDMs” tab for your VDM. Confirm its status is “permanently unloaded”. 4

Load the Virtual Data Mover to the peer Data Mover:  Select your VDM and click Properties.  Load the VDM to the Peer Data Mover by selecting it from the “Data Mover” drop-down list.  Click OK.  Review the information displayed in the” VDMs” tab for your VDM. Confirm it is assigned to your Peer Data Mover and its status is “OK”.

EMC Educational Services

194

Step 5

Action Create and mount a file system to a VDM:  Navigate to Storage > Storage Configuration > File Systems.  Click Create to create a new file system according to the following information: Create From: Storage Pool File System Name: File System Storage Pool: File Pool Storage Capacity: 5 GB Auto Extend Enabled: unchecked Thin Enabled: unchecked Slice Volumes: checked File-level Retention: Off Deduplication Enabled: unchecked VMware VAAI nested clone support: unchecked Data Mover (R/W): VDM Mount Point: Default  Click OK.  Review the information displayed in the “File Systems” tab for your File System. Confirm your VDM is shown as R/W in the “Data Mover” column. If the information is incorrect, select your File System and click Properties and make the needed corrections. Ask your instructor if you need assistance.

6

Move the VDM to the original Data Mover:  Navigate to Storage > Shared folders > CIFS and select the VDMs tab.  Select your VDM and click Properties.  Move the VDM to your Data Mover by selecting it from the “Data Mover” drop-down list.  Click OK.  A confirmation window is displayed about the move operation. Review the displayed message. Click the details link in the message.  Review the details of the move operation. Click OK to close the window. 

Click OK in the “Confirm” window to proceed with the move operation.

 Review the information displayed in the “VDMs” tab for your VDM. Confirm it is assigned to your Data Mover and its status is “OK”.

EMC Educational Services

195

Step 7

Action Verify the file system is mounted:  Navigate to Storage > Storage Configuration > File Systems.  Review the information displayed in the “File Systems” tab for your File System. Confirm your VDM is shown as R/W in the “Data Mover” column.

End of Lab Exercise

EMC Educational Services

196

Lab Exercise: CIFS Implementation Purpose:

To acquire the skills and knowledge to be able to configure and provide CIFS data access on a VNX system. The CIFS configuration will utilize a VDM that was created in an earlier lab exercise. You will prepare the VNX system for the CIFS implementation. You will create a CIFS Server on the VDM and join it to the lab’s Active Directory domain. You will create a top-level administrative share and a lower-level user share and access the shares. You will then move the VDM and its CIFS Server to the peer Data Mover and verify access to its shares. Note: Screenshots used in this Lab Exercise are meant to be used as examples. You may have different values/data on your VNX system.

Tasks:

In this lab exercise, you will perform the following tasks:    

References:

Prepare the system for CIFS Create and join a CIFS Server Create and access CIFS shares Move a VDM containing a CIFS Server

Configuring and Managing CIFS on VNX Configuring Virtual Data Movers on VNX

EMC Educational Services

197

Preparing for the Lab Please refer to your Class Configuration Sheet for this lab and record the values for each item listed. You will use these values for the lab exercise.

Student number:

__________________________________________________

VNX:

__________________________________________________

VNX Address (Control Station):

__________________________________________________

VNX Address (SPA):

__________________________________________________

VNX Address (SPB):

__________________________________________________

Data Mover:

__________________________________________________

Peer Data Mover:

__________________________________________________

VDM:

__________________________________________________

File System:

__________________________________________________

Network Device:

__________________________________________________

CIFS interface:

__________________________________________________

Data Mover Aaddress:

__________________________________________________

Peer Data Mover Address:

__________________________________________________

CIFS Server:

__________________________________________________

Windows Server:

__________________________________________________

EMC Educational Services

198

Lab: Part 1 – Preparing the system for CIFS Step 1

Action System Login:  (If you are not already logged in to your “Student Desktop”) Connect to your “Student Desktop” via your VDC connection.  From your Student Desktop, open a browser and login to Unisphere on your assigned VNX using the VNX Address (Control Station) and the user credentials: sysadmin/sysadmin with Scope Global selected.

2

Verify Data Mover DNS configuration: In this lab you will implement CIFS into the lab Active Directory domain hmarine.test. DNS is required for the AD environment and for VNX CIFS Server operations. To prepare for the CIFS implementation, you will need to verify and prepare both physical Data Movers in the VNX.  From the navigation bar drop-down list, select your VNX.  Navigate to Settings > Network > Settings for File and select the DNS tab.  Review the information displayed in the “DNS” tab for both “server_2” and “server_3”. Confirm that it matches the information below. DNS Domain: hmarine.test DNS Servers: 192.168.1.50 Protocol: tcp If the information is incorrect, inform your instructor before proceeding.

EMC Educational Services

199

Step 3

Action Verify Data Mover NTP configuration: Active Directory uses Kerberos for user authentication. Kerberos requires a time tolerance between all domain computers therefore NTP is commonly used for time synchronization in the domain.  Navigate to System > Hardware > Data Movers.  Select you Data Mover and click Properties.  Confirm the NTP configuration matches the information below. NTP Servers: 192.168.1.50 If the information is incorrect, inform your instructor before proceeding.  Click Cancel.  Repeat the verification for your Peer Data Mover.

4

Verify CIFS Service is Started on Data Movers:  Navigate to Storage > Shared Folders > CIFS  From the right-side Tasks pane in the “File Storage” section, click the Configure CIFS link.  In the Configure CIFS dialoge window, select server_2 from the “Show CIFS Configuration for” drop-down list.  Verify that the option “CIFS Serice Started:” is checked. If the option is not checked, check it and click OK. Also notify your instructor.  Select server_3 from the “Show CIFS Configuration for” drop-down list.  Verify that the option “CIFS Serice Started:” is checked. If the option is not checked, check it and click OK. Also notify your instructor.

EMC Educational Services

200

Step 5

Action Configure Data Mover Interface Name: You will be moving the VDM containing your CIFS Server from your Data Mover to your Peer Data Mover. CIFS Servers bind to network device interface names. Therefore the Data Movers need to have identical interface names for your CIFS server.  Navigate to Settings > Network > Settings for File and select the Interfaces tab.  Select your Data Mover Address and click Properties.  Modify the interface “Name:” to the CIFS interface. Leave all other interface settings unchanged. Click OK.

6

Create a CIFS Interface on the peer Data Mover:  With the Interfaces tab still selected, click Create to create a new interface for CIFS according to the following information: Data Mover: Select your Peer Data Mover Device Name: Network Device Address: Enter your Peer Data Mover Address Name: Enter your CIFS interface Netmask: 255.255.255.0 The Broadcast Address is calculated automatically Do not enter the MTU value Do not enter the VLAN ID value  Click OK. Review the information for the newly created interface. Verify it has been created with the correct information detailed above. If the information is incorrect, select the interface and click Properties to make the needed corrections. Ask your instructor if you need assistance.

End of Lab Exercise Part 1

EMC Educational Services

201

Lab: Part 2 – Create and Join a CIFS Server Step 1

Action Create a CIFS Server:  Navigate to Storage > Shared Folders > CIFS and select the CIFS Servers tab.  Click Create to create a CIFS Server according to the following information: Data Mover: Select your VDM Server Type: Active Directory Computer Name: Enter your CIFS Server Aliases: Leave blank NetBIOS Name: Leave blank Domain: hmarine.test Join the Domain: checked Domain Admin User Name: Administrator Domain Admin Password: emc2Admin! Organizational Unit: Leave at default value Enable local users: unchecked Interfaces: Checked for your Data Mover Address  Click OK. Review the information for the newly created CIFS Server. Verify it has been created with the correct information detailed above. If the information is incorrect, select the CIFS Server and click Properties to make the needed corrections. Ask your instructor if you need assistance.

2

Verify CIFS Server Domain Join:  From the “CIFS Servers” tab select your CIFS Server and click Properties. Note: You can use the “Filter” field on the page to help locate your CIFS Server. Input your Student number into the field to display your CIFS Server.  Review the information and verify the “Domain:” section displays the (Domain joined) comment. If the CIFS Server did not join the domain, you can retry the join operation detailed in the previous step. Ask your instructor if you need assistance.  Click Cancel.

End of Lab Exercise Part 2

EMC Educational Services

202

Lab: Part 3 – Create and Access CIFS Shares Step 1

Action Create a CIFS Share at the top-level of a VNX file system:  Navigate to Storage > Shared Folders > CIFS and select the Shares tab.  Click Create to create a CIFS Share according to the following information: Choose a Data Mover: Select your VDM CIFS Share Name: Top$ File System: Select your File System Path: Leave at the default NetBIOS Name: Leave blank CIFS Servers: Checked for your CIFS Server User limit: Leave blank Comment: Leave blank  Click OK.

2

Connect to your Windows Server:  From your Student Desktop system, launch the RDP Plus application that is available from the Desktop view or its taskbar.

 Connect to your Windows server according to the following information; Computer(s): Enter your Windows Server User: hmarine\Administrator Password: emc2Admin!  Click Connect.

EMC Educational Services

203

Step 3

Action Access your CIFS Share:  From the Windows server, launch the Run application that is available from the Desktop view or its taskbar.

 In the Open: field input the path to your top level share. The format of the path is: \\\ Where is your CIFS Server and is Top$  Click OK. The share opens to the .etc and lost+found folders. These folders are at the top-level of all the VNX file systems and should not be disturbed. To prevent inadvertent modifications to these folders by users, it is a best practice to create a lower-level share in the file system for users to access. 4

Create Data on the Share:  Create a folder on the share by right-clicking in the share window and select New > Folder. Name the new folder hmarine_data.  Open the ”hmarine_data” folder and create a new text file named test_data. Open the file and add some text to the file. Save and close the file.  Close the share window.

EMC Educational Services

204

Step 5

Action Create a CIFS Share with Computer Management tool: 

From the Windows server, launch the Computer Management application that is available from the Desktop view or its taskbar.



From the Action menu item, select Connect to another computer …



In the Another Computer: field, input your CIFS Server



On the left side tree, expand System Tools and Shared Folders containers. Right-click Shares and select the New Share option.

The Create A Shared Folder Wizard opens. 6

Create A Shared Folder Wizard: 

Click Next in the wizard Welcome window.



In the Folder Path window, click the Browse button. A Browse window opens.



In the Browse window, expand the tree for your File System. Select the hmarine_data folder in the tree. Click OK.



In the Folder Path window click Next.



The Name, Description, and Settings window opens. In the Share name: field, change the name displayed to HMARINE_SHARE. Click Next.



The Shared Folder Permissions window opens. Select the Customize permission option and click Custom.



A Customize Permissions window opens. In the Permissions for Everyone section, check the Allow Full Control option. Click OK.



In the Shared Folder Permissions window click Finish.



The Sharing was Successful screen opens and displays a summary of the share created. Click Finish.



Close the Computer Management application.

EMC Educational Services

205

Step 7

Action Access the lower-level share:  From the Windows server, launch File Explorer which is available from the Desktop view or its taskbar.

 From the left side tree, right-click Computer and select the Map network drive option.  In the Folder: field, enter the path to the HMARINE_SHARE. The format of the path is: \\\ Where is your CIFS Server and is HMARINE_SHARE  Leave all other options on the page at their default settings and click Finish.  The share opens and the test_data file create in a previous step is present. Notice the absence of the .etc and lost+found folders that were seen from the top-level share. This lower-level share demonstrates the best practice of preventing users from access and disturbing the .etc and lost+found folders.  Open the test_data file and verify its data is present. Add another line of text to the file. Do not save or close the file, just leave the file open in Notepad. The file will be left open for the last part of the lab exercise. Also leave the Remote Desktop connection session open to your Windows server. It will be used in the next part of the lab exercise.

End of Lab Exercise Part 3

EMC Educational Services

206

Lab: Part 4 – Move a VDM containing a CIFS Server Step 1

Action Verify Shares:  From your Student Desktop system Unisphere session, navigate to Storage > Shared Folders > CIFS and select the Shares tab. If your session is already at this page, refresh the Shares page. The page should display the two CIFS shares created, the top-level share created with Unisphere and the lower-level share created with Microsoft’s Computer Management tool. Note: Use the “Filter” field in Unisphere and input your Student number to limit the display to your shares.

2

Move the VDM to the peer Data Mover:     

Navigate to Storage > Shared Folders > CIFS and select the VDMs tab. Select your VDM and click Properties. From the Data Mover drop-down list, select your Peer Data Mover Click OK. A confirmation window opens for you to confirm the VDM move operation. Review the message displayed in the window. Optionally click the details link to view further details of the move operation. Click OK to proceed with the VDM move operation.  Review the information displayed on the “VDMs” tab for your VDM. It should display the VDM is now loaded to your Peer Data Mover.

EMC Educational Services

207

Step 3

Action Flush the CIFS client DNS cache:  Return to your existing Windows server Remote Desktop session. It is available on your Student Desktop system’s taskbar.

The Windows server is your CIFS client. In the previous part of this exercise, the client established a CIFS session to your CIFS server. The client performed a DNS lookup for your CIFS server and cached that lookup in its DNS cache. When the VDM containing the CIFS server was moved, the CIFS server binds to the interface of the Peer Data Mover and that interface has a different IP address. Therefore to reconnect to the CIFS server, the client’s DNS cache must be flushed so it can do a new DNS lookup for the CIFS server.  On your Windows server, open a Command window which is available from the Desktop view or its task bar.

 In the command window run the following command: ipconfig /flushdns 4

Access CIFS data after VDM containing CIFS server moves:  Return to your open test_data.txt file in Notepad. Add some text to the file and save the changes. When the CIFS server changes its IP address due to the VDM move operation, the existing CIFS session is disconnected. When the client performs a new write operation to the file, the client establishes a new CIFS session and reconnects to the share to perform the write operation to the file.  Leave the file open within the Notepad session.

EMC Educational Services

208

Step 5

Action Move the VDM back to the original Data Mover  From your Student Desktop system Unisphere session, navigate to Storage > Shared Folders > CIFS and select the VDMs tab.    

Select your VDM and click Properties. From the Data Mover drop-down list, select your Data Mover Click OK. In the confirmation window click OK to proceed with the VDM move operation.  Review the information displayed on the “VDMs” tab for your VDM. It should display the VDM is now loaded to your Data Mover. 6

Access the CIFS data after the VDM move without flushing DNS: 

Return to your existing Windows server Remote Desktop session.



Return to your open test_data.txt file in Notepad. Add some text to the file and save the changes.

The results of this operation can vary depending on how much time has passed since the new CIFS session was established in step 4 above. If enough time has passed for the client DNS cache to expire though its default timeout, the changes to the file will be saved normally. If the client DNS cache has not expired, you will receive an error stating “The specific network name is no longer available.”. The error can be cleared and access to the share returned by flushing the client’s DNS cache or waiting for its normal cache timeout to occur. 

On your Windows server close all open applications.



Disconnect from the Remote Desktop by accessing the Logoff Session icon which is available from the Windows server Desktop view or its taskbar.

End of Lab Exercise

EMC Educational Services

209

This page intentionally left blank

EMC Educational Services

210

Lab Exercise: VNX Snapsure Purpose:

In this lab, you will configure VNX Snapsure and observe some of its functions. You will also perform a file recovery and a file system restore.

Tasks:

In this lab exercise, you will perform the following tasks: 

Configure Snapsure



Create Checkpoints



Restore a File from a Checkpoint



Restore a file system from Checkpoints

References:

Using VNX SnapSure

EMC Educational Services

211

Preparing for the Lab Please refer to your Class Configuration Sheet for this lab and record the values for each item listed. You will use these values for the lab exercise.

Student number:

__________________________________________________

VNX:

__________________________________________________

VNX Address (Control Station):

__________________________________________________

VNX Address (SPA):

__________________________________________________

VNX Address (SPB):

__________________________________________________

Data Mover:

__________________________________________________

Data Mover Address:

__________________________________________________

File System 1:

__________________________________________________

Linux Host:

__________________________________________________

Linux Host Address:

__________________________________________________

Checkpoint 1:

__________________________________________________

File System 2:

__________________________________________________

VDM:

__________________________________________________

CIFS Share:

__________________________________________________

CIFS Server:

__________________________________________________

Windows Server:

__________________________________________________

Checkpoint 2:

__________________________________________________

Checkpoint 3:

__________________________________________________

Checkpoint 4:

__________________________________________________

Checkpoint 5:

__________________________________________________

EMC Educational Services

212

Lab: Part 1 – Configure Snapsure Step 1

Action Login to Unisphere:  (If you are not already logged in to your “Student Desktop”) Connect to your “Student Desktop” via your VDC connection.  From your Student Desktop, open a browser and login to Unisphere on your assigned VNX using the VNX Address (Control Station) and the user credentials: sysadmin/sysadmin with Scope Global selected.

2

Create a file system for NFS export: Create a new production file system using the available storage pool  From the navigation bar drop-down list, select your VNX.  Navigate to Storage > Storage Configuration > File Systems  Click Create and enter the following information: File System: File System 1 Storage Pool: File Pool Storage Capacity: 10 GB Choose Data Mover: Data Mover Keep all other defaults.  Click OK to complete the operation.

3

Create an NFS export for the newly created production file system: Create an NFS export from the file system created using the default path. Assign root access to your Linux host.    

Right-click File System 1 Select NFS Exports > Create NFS Exports from the sub-menu Use the default path of: /File System 1 From the Host Access section, in the Root Hosts: field; input your Linux Host Address.  Click OK to complete the operation.

EMC Educational Services

213

Step 4

Action Create user data:  From your Student Desktop, use PuTTY to open an SSH to the Linux Host.  Log into the host with the following credentials: logon as: root password: emc2Local!  From the terminal window, create a local directory to mount the file system that you have exported via NFS. Type the following: cd / mkdir /pfs1

 NFS mount this directory to the exported file system on your Data Mover. Type the following: mount Data Mover Address:/File System 1 /pfs1 df (confirm that the mount is listed)  Create data on the file system by running the following commands: cd /pfs1 dd if=/dev/zero of=Monday bs=256 count=10 dd if=/dev/zero of=Tuesday bs=256 count=10 dd if=/dev/zero of=Wednesday bs=256 count=10 dd if=/dev/zero of=Thursday bs=256 count=10

dd if=/dev/zero of=Friday bs=256 count=10  Verify the data is created by running the following command: ls The output should show one directory named lost+found and five files, one for each weekday.

EMC Educational Services

214

Step 5

Action Create a new checkpoint:  In Unisphere, navigate to Data Protection > Snapshots > File System Checkpoints  Click Create to make a new checkpoint with the following settings: Choose Data Mover: Data Mover Production File System: File System 1 Writeable Checkpoint: Unchecked Checkpoint Name: Checkpoint 1 Leave all other settings at default  Click OK to complete the operation.

6

View the checkpoint name:  To view the name of the checkpoint, run the following commands: cd /pfs1/.ckpt ls Record the name of the File Fystem 1 checkpoint directory. You will use the checkpoint name later in the exercise. __________________________________________________________ Note that the checkpoint name assigned in Unisphere is not the same as this directory name.

EMC Educational Services

215

Step 7

Action Create a file system to be CIFS shared: Create a new production file system using the available storage pool  Navigate to Storage > Storage Configuration > File Systems  Click Create and enter the following information: File System: File System 2 Storage Pool: File Pool Storage Capacity: 10 GB Choose Data Mover: VDM Keep all other defaults.  Click OK to complete the operation.

8

Create a CIFS share : Create a share using the newly created production file system.  Navigate to Storage > Shared Folders > CIFS  Click Create and enter the following information: Choose Data Mover: VDM CIFS Share Name: CIFS Share File System: File System 2 Path: /File System 2 CIFS server: CIFS Server  Click OK to complete the operation.

EMC Educational Services

216

Step 9

Action Connect to your Windows Server:  From your Student Desktop system, launch the RDP Plus application that is available from the Desktop view or its taskbar.

 Connect to your Windows server according to the following information; Computer(s): Enter your Windows Server User: hmarine\Administrator Password: emc2Admin!  Click Connect. 10

Access your CIFS Share:  From the Windows server, launch File Explorer which is available from the Desktop view or its taskbar.

 From the left side tree, right-click Computer and select the Map network drive option.  In the Folder: field, enter the path to the CIFS Share. The format of the path is: \\\ Where is the CIFS Server and is the CIFS Share. 

11

Leave all other options on the page at their default settings and click Finish.

Create user data:  In the mapped network drive create 12 new text files and name them for the months of the year (January through December).

EMC Educational Services

217

Step 12

Action Create a Snapshot: Create a snapshot of the newly created file system.  In Unisphere, navigate to Data Protection > Snapshots > File System Checkpoints  Click Create to make a new snapshot with the following settings: Choose Data Mover: VDM Production File System: File System 2 Writeable Checkpoint: Unchecked Checkpoint Name: Checkpoint 2 Leave all other settings at default  Click OK to complete the operation.

13

Verify checkpoint creation:  From the Windows server, launch File Explorer and expand the Computer directory.  Right-click your share and select Properties.  Click on the Previous Versions tab (this is the VSS Client).

Do you see the checkpoint you just created? What is the name of the File System 2 checkpoint? _______________________________________________________________

End of Lab Exercise Part 1

EMC Educational Services

218

Lab: Part 2 – Restore and Refresh Snapshots with NFS Step 1

Action Delete user data:  On your Linux host, verify that the files created in the previous section of the lab are still present in the mounted folder. ls –l /pfs1  Remove and verify the removal of the Tuesday file from File System 1 by running the following commands: cd /pfs1 rm Tuesday ls -l

 View the checkpoint content by running the following commands: cd /pfs1/.ckpt/ (recorded earlier) ls Do you see the file named Tuesday? ___________ If you do not, please inform your instructor. 2

Recover a deleted file with checkpoints:  Recover the deleted file from the checkpoint and verify the file recovery by running the following commands: cp Tuesday /pfs1 cd /pfs1 ls –l

You have just recovered an individual file from the point-in-time checkpoint using CVFS. This leaves all other copies of files as they are currently. If any new files had been created after the checkpoint, they are preserved.

EMC Educational Services

219

Step 3

Action Refresh a checkpoint:  Create a new file in /pfs1 named Saturday by running the following command: dd if=/dev/zero of=Saturday bs=256 count=10  Back in Unisphere, navigate to Data Protection > Snapshots > File System Checkpoints  Refresh the checkpoint named Checkpoint 1 by selecting it and clicking the Refresh button. Click OK to confirm the operation.  View the new name of the checkpoint by running the following command: ls /pfs1/.ckpt Record the name of the refreshed File system 1 checkpoint. You will use in in the following step. _______________________________________________________ Did the Checkpoint Refresh operation change the checkpoint name? _____________________________

4

Verify that the new file has been preserved by the checkpoint:  From the PuTTY SSH session to your Linux host, enter the following command: ls –al /pfs1 /.ckpt/ (recorded above)

EMC Educational Services

220

Step 5

Action Create a second checkpoint:  Create a new file in the /pfs1 directory named Sunday by running the following command: dd if=/dev/zero of=Sunday bs=256 count=10

 In Unisphere, create a new read-only checkpoint with the following settings: Choose Data Mover: Data Mover Production File System: File System 1 Writeable Checkpoint: Unchecked Checkpoint Name: Checkpoint 3 Leave all other settings at default  Click OK to complete the operation.  From the PuTTY SSH session to your Linux host, view the names of the checkpoints by running the following command: ls -l /pfs1/.ckpt There should be two checkpoint directories listed. 6

Restore from a SnapSure checkpoint:  From the PuTTY SSH session to your Linux host, remove any two files from the /pfs1 folder and confirm they have been successfully removed.  In Unisphere, select Checkpoint 3 and click Restore - when prompted, enter the new checkpoint name of Checkpoint 4 and click OK. When the operation is complete, from the PuTTY SSH session to your Linux host, view the contents of the /pfs1 folder using the ls command. Do you see a file for each day of the week? _________________

EMC Educational Services

221

Step 7

Action Restore from an earlier SnapSure checkpoint:  In Unisphere, select Checkpoint 1 and click Restore.  When prompted, enter the new checkpoint name of Checkpoint 5 and click OK.  When the operation is complete, view the contents of the /pfs1 folder on your Linux client using the ls command. You should see a file for Monday through Saturday. Why is the Sunday file not there? ____________________________________________________________ ____________________________________________________________ You have just performed a restore of a point-in-time checkpoint of the file system. This operation reverts all files to a previous data state and erases any files that were created after the checkpoint (e.g., the Sunday file).

8

Lab cleanup:  From the PuTTY SSH session to your Linux host, unmount and delete the /pfs1 directory.  From Unisphere, delete Checkpoint 5, Checkpoint 4, Checkpoint 3, Checkpoint 1, File System 1 NFS export and the File System 1 file system. Note: Leave the File System 2 and each one of the CIFS components to be used on the next part of the lab.

End of Lab Exercise Part 2

EMC Educational Services

222

Lab: Part 3 – Restore and Refresh Snapshots with CIFS Step 1

Action Checkpoint verification:  From the RDP Plus session to your Windows Server, verify that the CIFS share is still mapped and that there are 12 text files in the share named after each month of the year.  In Unisphere, verify that there is a checkpoint for File System 2 named Checkpoint 2.

2

Delete user data:  From your RDP Plus connection to your Windows Server, delete several files from the CIFS Share.

3

Restore from a checkpoint:  From the Windows server, launch File Explorer and expand the Computer directory.  Right-click your share and select Properties.  Click on the Previous Versions tab, select the checkpoint, and click Restore.  At the confirmation screen, click Restore once again.

 Ignore the two permissions warning messages by clicking Skip. The error relates to permissions on the .etc and lost+found directories and is expected.

EMC Educational Services

223

Step 4

Action Verify restored file system:  View the files in the CIFS share. Are there 12 text documents again? ___________ You have just restored a file system from a point-in-time checkpoint using Snapsure via the VSS Client. This will erase any files that were created after the checkpoint was created.

5

Recover individual files from a SnapSure checkpoint with VSS Client:      

From the File Explorer window, open the mapped CIFS share folder Delete January and February. Right-click the CIFS share object on the left-pane and select Properties Navigate to the Previous Versions tab. Select the checkpoint and click Open. Select January and February and copy them back to the CIFS Share folder.

You have just restored individual files from a point-in-time checkpoint using VSS Client. This allows all other files to remain in their current revision while recovering previous versions of specific files. 6

Lab cleanup:  From the File Explorer window, expand Computer from the left pane.  Right-click the mapped network drive to your CIFS share and select Disconnect.  In Unisphere, delete Checkpoint 2, the CIFS Share, and the File System 2.  Close your RDP session to the Windows server.

End of Lab Exercise

EMC Educational Services

224

End of Lab

EMC Educational Services

225

This page intentionally left blank

EMC Educational Services

226

Appendix: Windows User and Group Memberships Hurricane Marine Windows Users & Group Memberships HMARINE.TEST Domain Username Administrator EPallis EPing EPlace EPope EPratt EProh EPutter ESazi ESele ESimons ESong ESouth ESwailz ITallis ITechi ITei ITeribl LMinacci PTesca SEammi SEarly SEcho SElton SEmm SEpari SEttol SEwer SExtra SWai SWall SWari SWassi SWeir SWelles SWest SWillet SWitt SWong

Full Name Earl Pallis Elvin Ping Etta Place Eddie Pope Eldon Pratt Elliot Proh Egan Putter Ed Sazi Ellen Sele Eric Simons Eva Song Edgar South Evan Swailz Iggy Tallis Ira Techi Isabella Tei Ivan Teribl Liza Minacci Perry Tesca Sal Eammi Sage Early Sam Echo Santos Elton Sarah Emm Sadie Epari Saul Ettol Sean Ewer Sash Extra Seymore Wai Sergio Wall Seve Wari Seve Wassi Seda Weir Sema Welles Scott West Selena Willet Selma Witt Seiko Wong

Global Group Domain Admins Propulsion Engineers, Managers Propulsion Engineers Propulsion Engineers Propulsion Engineers Propulsion Engineers Propulsion Engineers Propulsion Engineers Structural Engineers Structural Engineers Structural Engineers Structural Engineers Structural Engineers, Managers Structural Engineers IS, DOMAIN ADMINS IS, DOMAIN ADMINS, Managers IS, DOMAIN ADMINS IS, DOMAIN ADMINS Director of Marketing, Managers President, Managers Eastcoast Sales Eastcoast Sales Eastcoast Sales Eastcoast Sales Eastcoast Sales, Managers Eastcoast Sales Eastcoast Sales Eastcoast Sales Eastcoast Sales Westcoast Sales Westcoast Sales Westcoast Sales, Managers Westcoast Sales Westcoast Sales Westcoast Sales Westcoast Sales Westcoast Sales Westcoast Sales Westcoast Sales

SWoo

Steve Woo

Westcoast Sales

EMC Educational Services

227

Appendix: Linux Users and Groups Hurricane Marine UNIX Users & Group Memberships - LDAP Domain hmarine.test Username

Full Name

Group

epallis

Earl Pallis

eping

Elvin Ping

engprop, mngr engprop engprop engprop engprop engprop engprop engstruc engstruc engstruc engstruc engstruc, mngr engstruc infotech infotech, mngr infotech infotech mngr mngr saleseas saleseas saleseas saleseas saleseas, mngr saleseas saleseas saleseas saleseas saleswes saleswes saleswes, mngr saleswes saleswes saleswes saleswes saleswes saleswes saleswes saleswes

eplace

Etta Place

epope

Eddie Pope

epratt

Eldon Pratt

eproh

Elliot Proh

eputter

Egan Putter

esazi

Ed Sazi

esele

Ellen Sele

esimons

Eric Simons

esong

Eva Song

esouth

Edgar South

eswailz

Evan Swailz

itallis

Iggy Tallis

itechi

Ira Techi

itei

Isabella Tei

iteribi

Ivan Teribi

lminacci

Liza Minacci

ptesca

Perry Tesca

seammi

Sal Eammi

searly

Sage Early

secho

Sam Echo

selton

Santos Elton

semm

Sarah Emm

separi

Sadie Epari

settol

Saul Ettol

sewer

Sean Ewer

sextra

Sash Extra

swai

Seymore Wai

swall

Sergio Wall

swari

Seve Wari

epallis

Seve Wassi

sweir

Seda Weir

swelles

Sema Welles

swest

Scott West

swillet

Selena Willet

switt

Selma Witt

swong

Seiko Wong

swoo

Steve Woo

EMC Educational Services

228

Appendix: Unisphere Browser and Java Messages

Unisphere is a Java-based web application that is accessed from a browser. The VNX secures the application using industry standard mechanisms to establish a secure http channel between the VNX and the storage administrator’s browser. The VNX uses self-signed certificates for securing the channel. The browser must also have Java installed to run the VNX Unisphere Java applications. When establishing a Unisphere session, the user will encounter a series of security related messages from the browser, from Java and from the VNX itself. The specific messages will vary with different browsers, different versions of Java JRE and with different versions of VNX software. This appendix captures the various messages a user will encounter with the following specific browser, Java and VNX OE software versions. It also details the actions to take to minimize the security messages seen for subsequent Unisphere sessions. Browser: Microsoft Internet Exporer version 10 Java: Version 7 update 25 VNX OE software: 05.33.000.5.015

The first security related message encountered is shown below. The browser message is displayed due to the browser not trusting the VNX self signed certificate. The user must click the Continue to this website (not recommended) action to proceed.

EMC Educational Services

229

The next messages that can be encountered are both displayed on the same page. The browser displays the nessages which relate to the Unisphere page requiring Java. The first is informational stating the minimum java version required. The user clicks OK to clear the message.

In the companion message below the browser is asking the user to allow the installed version to run. The user should select the drop-down list and select the option Allow for all websites. This message will not be seen on subsequent Unisphere sessions.

The next message that can be encountered is shown below. The message relates to an older version of Java being used and a newer version is available to download. For the lab exercises, please do not perform updates to Java. Check the Do not ask again until… tick-box and click the action: Later Continue and you … .

EMC Educational Services

230

This message relates to the VNX self-signed certificate and is displayed by Java. The use has to take action to proceed. Select the More Options/Hide Options toggle. Check the Always tust connections… tick-box and click Continue. This message will not be displayed again for subsequent Unisphere sessions.

The next message seen is displayed by Java and relates to the EMC published Unisphere java applet core.jar. The user must take action to allow Java to run the applet. Check the Do not show this again … tick-box and click Run. This message will not be displayed again for subsequent Unisphere sessions.

EMC Educational Services

231

The next message is similar to the previous but for a different EMC published java applet sslj.jar. The user must take action to allow Java to run the applet. Check the Do not show this again … tick-box and click Run. This message will not be displayed again for subsequent Unisphere sessions.

The next message is from Unisphere and relates to the self-signed certificate of SPA. Click Accept Always and this message will not be displayed for subsequent Unisphere sessions.

EMC Educational Services

232

The next message is similar to the previous message but is for SPB and it appears after the Unisphere Login page. Click Accept Always and this message will not be displayed for subsequent Unisphere sessions.

EMC Educational Services

233