Ubee Evw3226 Manual

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide

March 2013

www.ubeeinteractive.com Ubee Interactive Europe Beech Avenue 54-80 1119 PW Schiphol Rijk The Netherlands Sales (email): [email protected] Support (email) [email protected]

Notices and Copyrights 2013 Ubee Interactive. All rights reserved. This document contains proprietary information of Ubee and is not to be disclosed or used except in accordance with applicable agreements. This material is protected by the copyright laws of the United States and other countries. It may not be reproduced, distributed, or altered in any fashion by any entity (either internal or external to Ubee), except in accordance with applicable agreements, contracts, or licensing, without the express written consent of Ubee and the business management owner of the material. Ubee Interactive continuously improves its products and reserves the right to make changes to the products described in this document without notice. Ubee Interactive does not assume any liability that may occur due to the use of the product described in this document. All trademarks mentioned in this document are the property of their respective owners. This gateway is Wifi Alliance Certified:

Ubee Interactive

Contents 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9

Safety and Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Connections and Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Requesting Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Checking Package Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 EVW3226 Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 EVW3226 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Specifications, Standards, and Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Default Values and Logins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 LED Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2 Installing the EVW3226 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 2.1 2.2 2.3

Setting Up and Connecting the EVW3226 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Connecting Devices to the Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Troubleshooting the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3 Using the Web User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 4 The Status Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 4.1 4.2 4.3

Using the Connection Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Using the MTA Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Using the Diagnostics Option. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

5 The Basic Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 5.1 5.2 5.3

Using the Internet Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Using the Local Area Network Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Using the DHCP Client Devices Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

6 The Advanced Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8

Using the Options Option. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the IP Filters Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the MAC Filters Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the Port Filters Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the Forwarding Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the Port Triggers Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the DMZ Host Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the Firewall Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

35 36 38 39 40 43 45 46

7 The Parental Control Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49 7.1 7.2 7.3 7.4

Using the Parental Control Device Rules Option . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the Basic Setup Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the Web Site Filters Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the TOD Filters Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

49 50 52 53

December 2012 Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • January 2013

Ubee Interactive

8 The Wireless Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 8.1 8.2 8.3 8.4 8.5 8.6

Using the Wireless Radio Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the Security Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the Advanced Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the Access Control Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the WPS Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Deploying and Troubleshooting the Wireless Network . . . . . . . . . . . . . . . . . . . . . .

55 57 61 63 64 65

9 The System Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69 9.1 9.2 9.3 9.4

Using the Password Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the Switch Mode Option. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the Backup and Recovery Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the Log Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

69 70 71 74

10 The WIFI4ALL Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77 11 The DSLite Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79

December 2012 Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • January 2013

1

Introduction Welcome to the Ubee family of voice and data networking products. This guide is specific to the EVW3226 Advanced Wireless Voice Gateway and serves the following purposes:  Provides instructions on how to connect and operate the EVW3226.  Provides Web user interface instructions to configure and manage the EVW3226.  Provides the technical details needed to locally manage the EVW3226. This can involve obtaining information from the gateway for support and troubleshooting. Topics See the following topics:

 Safety and Regulatory Information on page 1  Connections and Applications on page 4  Requesting Support on page 4  Checking Package Components on page 4  EVW3226 Rear Panel on page 5  EVW3226 Front Panel on page 6  Specifications, Standards, and Firmware on page 7  Default Values and Logins on page 9  LED Operations on page 10

1.1

Safety and Regulatory Information Use the following information to better understand safety and regulatory standards to install, maintain, and use the EVW3226 Advanced Wireless Voice Gateway.

1.1.1

Safety WARNING: The following information provides safety guidelines for anyone installing and operating the EVW3226. Read all safety instructions in this guide before attempting to unpack, install, operate, or connect power to this product. Follow all instruction labels on the gateway itself. Comply with the following safety guidelines for proper operation of the gateway.

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

1

Ubee Interactive

Follow basic safety precautions to reduce the risk of fire, electrical shock, and injury. To prevent fire or shock hazard, do not expose the unit to rain and moisture or install this product near water. Never spill any form of liquid on or into this product. Do not use liquid cleaners or aerosol cleaners on or close to this product. Clean with a soft dry cloth. Do not insert objects into the product’s module openings or empty slots. Doing so can accidentally damage its parts and/or cause electric shock. Electrostatic discharge (ESD) can permanently damage semiconductor devices. Always follow ESD-prevention guidelines for equipment handling and storage. Use only the power adapter supplied with the gateway. Do not attach the power supply cable to building surfaces or floorings as this can damage the cable.  Rest the power cable freely without any obstacles. Do not place heavy items on top of the power cable. Do not abuse, step, or walk on the cable.  Do not put any objects on top of the gateway as ventilation can be impacted. Do not place the gateway on an unstable stand or table; it can fall and become damaged.  To protect the equipment from overheating, do not block the slots and openings in the module housing that provide ventilation. Do not expose the EVW3226 to direct sunlight. Do not place hot devices close to the gateway; it may degrade it or cause damage.

1.1.2

Eco-Environmental Statements The following eco-environmental statement applies to the EVW3226. Packaging Collection and Recovery Requirements: This product should not be disposed of with household waste. Contact your city authorities for information on how electrical appliances can be recycled. For more information regarding collection and recovery of packaging and packaging waste within specific jurisdictions, contact Ubee Interactive at www.ubeeinteractive.com.

1.1.3

Regulatory Conformity Ubee Interactive Corporation warrants that the EVW3226 Advanced Wireless Voice Gateway meets the requirements for compliance in relation to the following directives:  2002/95/EC (The RoHS Directive) restricting the use of hazardous substances in all Electrical and Electric Equipment.  2002/96/EC (The WEEE Directive) preventing/reducing Waste Electrical and Electronic Equipment (WEEE).  2006/95/EC (The Low Voltage Directive) regulating all health and safety risks of electrical equipment operating within certain voltage ranges.

2

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

Ubee Interactive

 2004/108/EC (The Electromagnetic Compatibility Directive) ensuring that (i) electromagnetic emissions do not disturb radio and telecommunication or other equipment and (ii) the immunity of the products/equipment supplied to interference.  1999/5/EC (The R&TTE Directive) ensuring that radio communications and telecommunications terminal equipment (R&TTE) is safe and does not disturb radio services or other equipment.  2009/125/EC (The Eco Design Directive) establishing a framework for the setting of eco-design requirements for energy-using products as well as any relevant regulation made thereunder including, if appropriate, but not limited to the Standby Regulation (EC) No 1275/2008 with regard to eco-design requirements for standby and off mode electric power consumption of electrical and electronic household and office equipment (The Standby Regulation) and regulation (278/2009) (The Power Supply Regulation). The following standards apply:         

EN300328 EN301893 EN301489-1 EN301489-17 EN50385 EN55022 EN55024 EN60950-1 EN301893

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

3

Ubee Interactive

1.2

Connections and Applications The following diagram illustrates the general connection topology and applications of the EVW3226.

1.3

Requesting Support Subscribers must contact their service provider for direct support. EVW3226 Advanced Wireless Voice Gateway documentation support may be available at: http://www.ubeeinteractive.com

1.4

Checking Package Components The package for the EVW3226 contains the following items: Item

Description 1 - RJ45 Ethernet Cable (yellow) Length ~ 1.55 m

Sample image, actual appearance subject to change.

4

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

Ubee Interactive

Item

Description 1 - EVW3226 User Manual and Documentation CD Includes:

 Quick Installation Guide  User Manual (multilingual)  Safety Notice

1 - AC Adapter (for EU) Input: 207-240V ~, 50-60Hz Output: 12V 2A Only use the original power supply unit that was shipped with your EVW3226 Advanced Wireless Voice Gateway.

Sample image, actual appearance subject to change.

1 - AC Adapter (for the UK and Ireland) Input: 207-240V ~, 50-60Hz Output: 12V 2A Only use the original power supply unit that was shipped with your EVW3226 Advanced Wireless Voice Gateway.

Sample image, actual appearance subject to change.

Please note that you will receive 1 power supply unit with your gateway, appropriate to your country of residence.

1.5

EVW3226 Rear Panel Review the following image and descriptions of the rear panel connections on the gateway.

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

5

Ubee Interactive

Item

1.6

Description

TEL1 TEL2

Connects to a standard analog telephone using an RJ11 cable. Telephone service must be enabled through the service provider.

ETH1 ETH2 ETH3 ETH4

Connects to Ethernet devices such as computers, gaming consoles, and/or routers/hubs using an RJ45 cable. Each ETH port on the back panel of the gateway has an LED to indicate its status when an Ethernet device is connected:  LED is Orange when connected at 10/100 Mbps speeds.  LED is Green when connected at 1000 speeds (Gigabit Ethernet).  LED blinks when data is being transferred to and from the connected device.

USB

USB Host Port: provides a port to connect a USB device. This feature may not be enabled on your gateway.

RF

Connects to the cable outlet of your service provider, or a cable splitter connected to the cable outlet.

RESET

Restores the default settings of the EVW3226 including wireless and custom gateway settings. Use a pointed object to push down the reset button for 5-10 seconds until the power LED turns off. After the power LED turns off, release the button. If the Reset button is pressed for less than 5 seconds, it will cause the gateway to reboot.

POWER ON/OFF SWITCH

Powers the EVW3226 on and off. NOTE: If the switch is in the off position, no telephone calls can be placed or received.

POWER

Connects the power adapter to the gateway. Use only the power adaptor provided with the EVW3226.

WPS

Connects a PIN-protected Wi-Fi device when the Wi-Fi Protected Setup method is used. When the WPS button is pushed or triggered through the EVW3226’s Web UI, an LED on the top-front of the gateway flashes for two minutes until a PIN is entered from the wireless client, such as a laptop computer, that wants to connect. After a Wi-Fi client attaches successfully, the LED remains on for 5 minutes and turns off. Refer to Using the WPS Option on page 64 for more information.

EVW3226 Front Panel The following image represents the front panel of the EVW3226. For LED descriptions, refer to LED Operations on page 10.

6

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

Ubee Interactive

WPS Button

The WPS (WiFi Protected Setup) button is located on the right side of the EVW3226. Refer to Using the WPS Option on page 64 for its function.

1.7

Specifications, Standards, and Firmware Following is a list of the features and specifications of the EVW3226. Interfaces and Standards        

Cable: F-Connector, female 4 RJ45 ports supporting 10/100/1000 Mbps USB: 1 USB 2.0 host port Telephony: 2 RJ11 ports, PacketCable1.5 Certified EuroDOCSIS 3.0 certified DOCSIS 3.0 compliant DOCSIS/EuroDOCSIS 1.0/1.1/2.0 compliant CE certified, WiFi Alliance certified

Downstream*    

 

 

Frequency Range: 108 MHz ~ 1002 MHz Modulation: 64 / 256 QAM Channel Bandwidth: 8 MHz or 6 MHz Maximum Data Rate per Channel (up to 8 channels): DOCSIS = 30 Mbps (64 QAM), 42 Mbps (256 QAM) EuroDOCSIS = 41 Mbps (64 QAM), 55 Mbps (256 QAM) Total Max Bandwidth (8 Channels): DOCSIS = 342 (304) Mbps, EuroDOCSIS = 444 (400) Mbps Symbol Rate: DOCSIS: 5.056941 Msym/s (64-QAM) and 5.360537 Msym/s (256-QAM) EuroDOCSIS: 6.952 Msym/s (64-QAM and 256-QAM) RF Input Power: -15 to +15dBmV (64 QAM), -15 to +15dBmV (256 QAM) Input Impedance: 75 Ω

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

7

Ubee Interactive

Upstream*  Frequency Range: 5MHz ~ 85MHz  Modulation: A-TDMA: QPSK, 8, 16, 32, 64QAM S-CMDA: QPSK, 8, 16, 32, 64, 128QAM  Max Bandwidth of 4 Channels = 122.88 (108) Mbps, bandwidth per channel (up to 4 channels) = [QPSK 0.32 ~ 10.24 Mbps, 8 QAM 0.48 ~ 15.36 Mbps, 16 QAM 0.64 ~ 20.48 Mbps, 32 QAM 0.80 ~ 25.60 Mbps, 64 QAM 0.96 ~ 30.72 Mbps, 128 QAM/TCM 30.72 Mbps]  Symbol Rate: 160, 320, 640, 1280, 2560, 5120 Ksps  RF Output Power: TDMA/ATDMA: +8dBmV to +54dBmV (32/64 QAM). ATDMA Only: +8dBmV to +55dBmV (8/16 QAM), +8dBmV to +58dBmV (QPSK). S-CDMA: +8dBmV to +53dBmV (all modulations) *Actual speeds vary based on factors including network configuration. Security and Network  Supports multiple SSIDs, 802.11 a/b/g/n certified with link speeds up to 300 Mbps, 2 Tx and 2 Rx antennas  DHCP Client/Server, Ethernet 10/100/1000 BaseT, full-duplex auto-negotiate functionality, IPv4 and IPv6 support  NAT Firewall, MAC/IP/Port Filtering, Parental Control, Stateful Packet Inspection (SPI), DoS Attack Protection, WPS/ WPA/ WPA2/ WPA-PSK & 64/128-bit WEP Encryption  VPN Pass-Through Voice       

SIP (RFC3261) Ring Voltage: 270 VAC, pk-pk (tip-ring) Line Voltage Onhook: -48 Volts Loop Current: 20mA / 41mA Ring Capability: 2K ft., 5REN Hook State: Signaling Loop Start DTMF Tone Detection, T.38 FAX relay (G.711), Echo Cancellation (G.168) / Silence Suppression, Voice Active Detection, and Comfort Noise Generation

Gateway Management     

Supports IEEE 802.11e Wi-Fi Multimedia (WMM) Power Save DOCSIS/EuroDOCSIS, Web-Based Firmware upgrade via TFTP Configuration backup and restore SNMP support

Physical and Environmental  Dimensions: 240mm (W) x 172mm (D) x 42mm (H)  Weight: 548 g

8

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

Ubee Interactive

 Power Supply Unit: Input AC 207~240V 50~60Hz. Output DC 12V 2A.  Operating Temperature: 0°C ~ 40°C  Humidity: 5~95% (non-condensing)

1.8

Default Values and Logins The EVW3226 is pre-configured with the following parameters. Some operators may change default values. Check with your cable operator to determine the default values for your region. Local Port Address: 192.168.0.1, Web Interface: http://192.168.0.1 Subnet Mask: 255.255.255.0 Operation Mode: Router Mode Wireless Defaults:  Primary SSID (subscriber-managed) = “UPC” plus 7 automatically generated numeric characters. Example: UPC1234567.  WPA Pre-shared Key/Password/Passphrase = Unique key for each gateway. Also called the network key. Refer to Using the Security Option on page 57. The Passphrase will be automatically generated comprised of 8 characters, upper case, A-Z only (with the exception of L,I and O). Example: ABCDEFGH. The SSID and the passphrase is printed on the product label. See the example below:

 Wireless Security = WPA/WPA2-PSK encryption 

Standard User Web Interface Login: Username: admin Password: admin

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

9

Ubee Interactive

1.9

LED Operations The following table summarizes the EVW3226 LEDs. Front Panel LEDs

Position

Color

Label

Green/ LED1

Behavior Solid On

Red

Red: Abnormal status

Green/

Green: Power on, DS lock without channel bonded DS

Blue

Blue: Power on, DS lock with channel bonded

Green/

Green: Power on, US lock without channel bonded

LED3

Blinking

Green: Power Good PWR

LED2

Off

US

Power off

Slow: Self Test

DS no link

Slow: Channel scan

US no link

Slow: Channel scan

Blue: Power on, US lock with channel bonded

Blue LED4

Green

RDY

Ready for operation

EVW3226 off or not online

Slow: Self test or initializing functions

LED5

Green

TEL1

Port registration OK

VoIP is not online

Slow: Registration in progress or VoIP off-hook

LED6

Green

TEL2

Port registration OK

VoIP is not online

Slow: Registration in progress or VoIP off-hook

WLAN is off

FAST: Activity

Green/ LED7

Green: 2.4GHz Link WLAN

Blue LED8

10

Green

Blue: 5GHz Link WPS

WPS success

WPS in progress

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

2

Installing the EVW3226 Use the information in this chapter to set up and connect the EVW3226, connect additional devices, and troubleshoot the installation. Topics See the following topics:

 Setting Up and Connecting the EVW3226 on page 11  Connecting Devices to the Network on page 13  Troubleshooting the Installation on page 15

2.1

Setting Up and Connecting the EVW3226 Use the following instructions to set up and connect the EVW3226. When the gateway is set up and connected, refer to Using the Web User Interface on page 17 for configuration instructions. Important: If in doubt, subscribers should contact their service provider to enable Internet access and telephony service. Steps To set up the EVW3226: 1. Remove the EVW3226 gateway, power supply and cables from the packaging. 2. Place the EVW3226 in the best location to connect to other devices, such as PCs or gaming consoles.  Place the wireless gateway and wireless clients in open areas far away from transformers, heavy-duty motors, microwave ovens, refrigerators, fluorescent lights, and other manufacturing equipment. These items can impact wireless signals. A wireless signal can become weaker after it has passed through metal, concrete, brick, walls, or floors.  Place the gateway in a dry location that has an operating temperature of 0˚ C to 40˚ C. Refer to Safety and Regulatory Information on page 1 for more safety information. 3. Power on your PC. The PC must have an Ethernet network adapter or Ethernet port and an Internet browser installed, such as Chrome or Internet Explorer. 4. Connect the power adapter included in the product package to the back of the gateway and plug the other end into the power outlet. 5. Connect the network cable included in the product package to your computer’s Ethernet port. Connect the other end to the ETH1, ETH2, ETH3, or ETH4 port of the gateway.

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

11

Ubee Interactive

6. Connect a coaxial cable from the RF port on the back of the EVW3226 to the cable wall outlet, a cable splitter connected to the wall outlet, or follow your cable operator’s instructions on how to connect the gateway to the cable network. 7. Validate the network connection using the gateway LEDs to confirm operations. Refer to LED Operations on page 10 for more information.  The WLAN LED must be solidly lit.  The PWR, DS, US, and RDY LEDs are solidly lit.

2.1.1

Wall Mount Installation You can mount the EVW3226 on a wall using the two mounting brackets on the bottom of the gateway. Two round or pan head screws are recommended. See the figure below. Head Diameter

5.0-5.5 mm

Screw Diameter

2.9-3.0 mm

Screw Length

8.2-9.0 mm

Head Height

1.8-2.2 mm

Steps To mount the EVW3226 on a wall: 1. Install the two screws horizontally on a wall 194mm apart. See the figure below.

12

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

Ubee Interactive

The screws should protrude from the wall so that you can fit the EVW3226 between the head of the screw and the wall. If you install the screws in drywall, use hollow wall anchors to ensure that the unit does not pull away from the wall due to prolonged strain from the cable and power connectors. 2. Mount the gateway on the wall.

2.2

Connecting Devices to the Network Use the instructions below to connect network devices and validate gateway functionality. Topics See the following topics:

 Connecting an Ethernet Device on page 13  Connecting a Wireless Device on page 14  Connecting a Telephone Line on page 15

2.2.1

Connecting an Ethernet Device You can connect up to four Ethernet devices to the EVW3226. Steps To connect another Ethernet device to the network: 1. Connect the Ethernet cable from the Ethernet device (for example, a PC or gaming console) to an open Ethernet port on the back of the EVW3226. 2. Use the EVW3226 LEDs to confirm operations. Refer to LED Operations on page 10

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

13

Ubee Interactive

on page 1 for more information. 3. Open a Web browser and go to any Web site to validate network/Internet connectivity (for example, http://www.wikipedia.org). 4. If the connected device is a gaming console, perform any online task supported by the console (for example, log into the gaming server, play an online game, download content). Note Refer to Troubleshooting the Installation on page 15 for troubleshooting information.

2.2.2

Connecting a Wireless Device Use the following steps to connect a wireless device to the gateway (for example, a laptop computer). Default values are shown in the steps below. Steps To connect a wireless device to the gateway: 1. Access the wireless networking feature on your wireless device. On a Windows 7 computer, open the Control Panel and click on Network and Sharing Center. 2. Click Manage Wireless Networks. The EVW3226 is shipped with a default SSID (service set identifier). The SSID is the name of the wireless network broadcast from the gateway so that wireless clients can connect to it. 3. Double-click the SSID of the EVW3226 in the wireless networks window. The default SSID is “UPC” plus 7 automatically generated numeric characters. Example: UPC1234567. For the SSID of your gateway, please consult the label on the bottom of your EVW3226 or the Quick Installation Guide that shipped with it. 4. When prompted, enter the network key, also called the pre-shared key or password. The WPA Pre-shared Key/Password is a unique key for each gateway.  The Password will be automatically generated comprised of 8 characters, upper case, A-Z only (with the exception of L,I and O). Example: ABCDEFGH. For your WPA Password, please consult the label on the bottom of your gateway or the Quick Installation Guide that shipped with it.

14

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

Ubee Interactive

5. Confirm connectivity by opening a Web browser and going to any Web site (for example, http://www.wikipedia.org) or access the Web interface for the EVW3226 (refer to Using the Web User Interface on page 17). Note The Web interface allows you to customise the configurations and capabilities for the EVW3226. For a full explanation of all Web interface functions, refer to Using the Web User Interface on page 17. If you have wireless issues or questions, refer to Deploying and Troubleshooting the Wireless Network on page 65.

2.2.3

Connecting a Telephone Line You can connect up to two telephone lines to the EVW3226 to use the telephone (voice) features. Voice service must be enabled by the service provider. Steps To connect a telephone line: 1. Connect an analog telephone to the TEL1 or TEL2 jack on the back panel of the EVW3226 using an RJ11 telephone cable. 2. Pick up the telephone and listen for a dial tone. 3. Make a phone call, have someone call you, or call your number with a cell phone to verify a successful connection.

2.3

Troubleshooting the Installation Use the following tips to troubleshoot the installation.  None of the LEDs are on when I power on the EVW3226.  Ensure that the power switch on the back of the gateway in switched to the “ON” position.  Check the connection between the power outlet and the power adapter. Verify the power outlet is energized and the power adaptor is connected to the power outlet.  Check the connection between the power adapter and the gateway. Power off the gateway and wait for 5 seconds and power on the gateway again. If the problem still exists, there may be a hardware problem.  The ETH1, ETH2, ETH3, or ETH4 LEDs on the back of the gateway are not lit where Ethernet cables are connected.  Restart the computer so that it can re-establish a connection with the gateway.  Check for a resource conflict (Windows users only): 1.

Right-click My Computer on your desktop and choose Properties.

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

15

Ubee Interactive

2.

Choose the Device Manager tab and look for a yellow exclamation point or red X over the network interface card (NIC) in the Network Adapters field. If you see either one, you may have an interrupt request (IRQ) conflict. Refer to the manufacturer’s documentation for further assistance.

 Verify that TCP/IP is the default protocol for your network interface card.  Power cycle the gateway by removing the power adapter from the electrical outlet and plugging it back in. Wait for the gateway to re-establish communications with your cable service provider.  Check General Connectivity Issues:  If your PC is connected to your own router or switch device, connect the PC directly into an Ethernet port on the gateway.  If you are using a cable splitter, remove the splitter and connect the gateway directly to the cable wall outlet. Wait for the EVW3226 to re-establish communications with the cable service provider. Refer to the cable outlet installation instructions from your cable operator. There may be an antenna amplifier or other equipment from the cable operator required.  Try a different cable. The Ethernet cable may be damaged.  If none of these suggestions work, contact your cable service provider for further assistance.

16

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

3

Using the Web User Interface The Web user interface (UI) for the EVW3226 is easy to use and allows you to view and configure several settings for your wireless gateway. You can validate the installation by accessing the Web user interface on the gateway. Access the Web user interface for the EVW3226 from a Web browser, such as Internet Explorer on a Windows computer. Default values are shown in the steps below. Steps To access the Web user interface: 1. Ensure your PC is connected to the EVW3226 via the Ethernet cable or wireless connection (refer to Connecting a Wireless Device on page 14). Launch an Internet browser, such as Internet Explorer, from your computer. 2. Enter the following IP address in the address bar of the browser window and press the Enter key. http://192.168.0.1 (Note that if the EVW3226 is in bridge mode, the IP address for accessing the Web UI is http://192.168.100.1. Refer to Using the Switch Mode Option on page 70).

3. Enter the username and password in the authentication dialog box.  If this is the first time you are accessing the user interface (or after a factory reset of the gateway), you will be prompted to select your country and language from the initial screen.

 Standard User Web Interface Login: Username: admin Password: admin

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

17

Ubee Interactive

The initial screen displayed after login is the Status screen. It displays information about the EVW3226.

For descriptions of the Status menu, refer to The Status Menu on page 19.

18

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

4

The Status Menu The Status menu of the Web user interface allows you to access information about the gateway such as software, connection (downstream and upstream), MTA (multimedia terminal adapter), and diagnostics. Topics See the following topics:

 Using the Connection Option on page 19  Using the MTA Option on page 22  Using the Diagnostics Option on page 24 Steps To access status options: 1. Click Status from the main menu.

4.1

Using the Connection Option The Connection option displays the gateway’s basic software information as well as upstream and downstream connection information. Topics See the following topics:

 Using the Basic Connection Option on page 19  Using the Upstream Connection Option on page 20  Using the Downstream Connection Option on page 21

4.1.1

Using the Basic Connection Option Steps To view the Basic Connection information: 1. Click Status from the main menu. 2. Click Basic from the left side menu under Connection. The field descriptions are listed below the screen example.

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

19

Ubee Interactive

Label

4.1.2

Description

Connectivity State

Displays connection status. In normal operations it will show: OPERATIONAL.

Boot State

Displays the status on boot up and if the gateway is operational.

Security

Displays the status of the security settings: enabled/disabled.

CM IP Address

Displays the CM (cable modem’s) IPv4 (Internet Protocol version 4) Address.

CM IPv6 Address

Displays the cable modem’s IPv6 Address.

CM Lease Time

Displays the lease time in seconds. When the lease time expires, the PC must connect to the DHCP server.

CM Lease Expiration

Displays the date and time when the lease expires in yyyymm-dd hh:mm:ss. For example: “2012-12-13 12:12:12”.

System Time

System Time is provisioned by the server. Before the gateway is online it will display a time counted from 1970-0101 00:00:00.

Using the Upstream Connection Option Steps To view the Upstream Connection information: 1. Click Status from the main menu. 2. Click Upstream from the left side menu under Connection. Field descriptions are

20

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

Ubee Interactive

listed below the screen example.

Label

4.1.3

Description

Transmitter #

The transmitter index.

Channel ID

Displays the current cable modem (the EVW3226’s) upstream channel ID.

Lock Status

Displays if the cable modem succeeded in locking to an upstream channel.

Frequency

Displays the current cable modem upstream frequency in hertz.

Modulation

The current cable modem upstream modulation type.

Symbol Rate

Displays the symbol rate in 1000 symbols per second.

Channel Type

Displays the channel type.

Power

Displays the current cable modem upstream transmit power in decibel millivolts (dBmV).

Using the Downstream Connection Option Steps To view the Downstream Connection information: 1. Click Status from the main menu. 2. Click Downstream from the left side menu under Connection. Field descriptions are listed below the screen example.

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

21

Ubee Interactive

Label

4.2

Description

Receiver #

The receiver index.

Channel ID

Displays the current cable modem downstream channel ID.

Lock Status

Displays if the cable modem succeeded in locking to a downstream channel.

Frequency

Displays the current cable modem downstream frequency in Megahertz (MHz).

Modulation

Displays the modulation method for the downstream channel (64 / 256 QAM).

Symbol Rate

Displays the symbol rate in 1000 symbols per second.

SNR

Displays the signal-to-noise (SNR) ratio, the desired signal level to the background noise level.

Power

Displays the current cable modem downstream receive power in decibel millivolts (dBmV).

Using the MTA Option The MTA screen displays telephony information about the gateway’s initialisation of the MTA (multimedia terminal adapter).

22

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

Ubee Interactive

Steps To view connection information: 1. Click Status from the main menu. 2. Click Status under MTA from the left side menu. Field descriptions are listed below the screen example. 95

Label

Description

Startup Procedure Telephony DHCP

Telephony Security

Displays the DHCP (Dynamic Host Configuration Protocol) provisioning status of the MTA. Possible values are: 1.

Not Initial

2.

DHCP Discovered

3.

DHCP Offer Message

4.

DHCP Not Discovered

5.

DHCP Complete

Displays the security.

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

23

Ubee Interactive

Label

Description

Telephony TFTP

Displays if the TFTP (Trivial File Transfer Protocol) provisioning status. Possible values are: 1.

Not Initial

2.

TFTP Server DNS Request

3.

TFTP Server DNS Reply

4.

TFTP Start

5.

TFTP Complete

Telephony Call Server

Displays the provisioned call server’s address.

Telephony Provisioning Status

Displays the status of the MTA provisioning.

MTA Line State Line 1, Line 2

Displays the telephone line connections. Possible values are: 1.

Off Hook

2.

On Hook

3. Registered 4. N/A

4.3

Using the Diagnostics Option Use the Diagnostics option to test network connectivity. Two utilities are available: Ping and Trace Route. Topics See the following topics:

 Using the Ping Option on page 24  Using the Trace Route Option on page 25

4.3.1

Using the Ping Option Use the Ping utility to test network connectivity between devices by sending a test message to a specific device. You can also confirm the size of data sent is the same as the size of data received. Steps To test connectivity between devices: 1. Click Status from main menu. 2. Click Ping from the left side menu.

24

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

Ubee Interactive

3. Enter new parameter values or accept the default values. 4. Click Start. Field descriptions are listed below the screen example.

Label

4.3.2

Description

Destination IP

Defines the IP address to which you want to send a ping.

Packet Size

Defines the packet size (bytes of data) to send for the ping operation.

Packet Count

Defines the number of packets to send to the destination IP.

Start

Starts the ping test.

Abort

Aborts the ping test.

Using the Trace Route Option The Trace Route utility determines the IP addresses of hosts in the network path. By checking the Resolve Host names box, Trace Route tries to find which name matches the address. Some hosts have no names, and might still be shown as IP addresses, even if this option is active. Steps To trace host IP addresses along a route: 1. Click Status from main menu. 2. Click Trace Route from the left side menu.

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

25

Ubee Interactive

3. Enter new parameter values or accept the default values. 4. Click Start. Field descriptions are listed below the screen example.

Label

26

Description

Host IP

Defines the specific IP address or domain (for example, ubeeinteractive.com) to which you want to trace a route.

First TTL (Time to Live)

Defines the starting number of hops. Hops are the number of routers the trace route traverses. Default is 1.

MAX TTL

Defines the maximum number of hops. Hops are the number of routers the trace route traverses. Default is 5

Start

Starts the trace route test.

Abort

Aborts the trace route test.

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

5

The Basic Menu Basic gateway options provide the majority of configuration for the EVW3226 including WAN IP addresses, LAN IP addresses, and DHCP. Advanced gateway options provide settings like MAC filtering and port forwarding. Topics See the following topics:

 Using the Internet Option on page 27  Using the Local Area Network Option on page 29 Steps To access the basic menu: 5. Click Basic from the main menu.

5.1

Using the Internet Option Use the Internet option to configure basic gateway features related to your Internet Service Provider (ISP) connection. Steps To configure Internet options: 1. Click Basic from the main menu. 2. Click Internet from the left side menu. Field descriptions are listed below the screen examples. Note The IP address displayed in the screen depends on the router mode.  If the gateway is in IPv4 only mode, the IP address and subnet mask will be displayed.  If the gateway is in IPv6 mode, the IPv6 address will be displayed.  If the gateway is in dual stack mode, it will display both.

Ubee EVW322 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

27

Ubee Interactive

Dual Stack Mode Screenshot:

Label

Description

LAN IP Address

Displays the Internet IP address obtained from the service provider.

Subnet Mask

Displays the subnet mask of the Internet IP address.

IPv6 Address

Displays the global IPv6 address obtained from the server and the link local IPv6 address.

MAC Address

Displays the WAN interface’s hardware address.

Expires On

Displays when the WAN IP address expires, if applicable.

Host Name

Defines the host name for the router. This may be required by some service providers.

Domain Name

Defines the domain name for the router. This may be required by some service providers.

WAN IP Renew

Renews the WAN IP address when clicked.

Save

Saves all the changes made in this screen when clicked.

Note: The label descriptions above also apply to the IPv4 and IPv6 Mode screenshots below.

28

Ubee EVW322 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

Ubee Interactive

IPv4 Mode Screenshot:

IPv6 Mode Screenshot:

5.2

Using the Local Area Network Option Use the Local Area Network option to configure the Local Area Network and DHCP Server.

Ubee EVW322 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

29

Ubee Interactive

Steps To configure Local Area Network options: 1. Click Basic from the main menu. 2. Click Local Area Network from the left side menu. Field descriptions are listed below the screen examples. Note The IP address displayed in the screen depends on the router mode.  

If the gateway is in IPv4 only mode, the IP address and subnet mask will be displayed. If the gateway is in IPv6 mode, the IPv6 address and prefix will also be displayed.

IPv4 Mode Screenshot:

30

Ubee EVW322 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

Ubee Interactive

Label

Description

IP Address

Defines the local IP address, which is the default gateway address for all LAN hosts that connect to the EVW3226.

IP Mask

Defines the subnet mask value.

MAC Address

Displays the LAN interface’s hardware address.

DHCP Server

Configures the status of the DHCP server feature (Enabled/Disabled).

Starting Local Address

Defines the starting private IP address for the pool of IP addresses that can be used by connecting clients. Private addresses are translated to public IPs to be used on the network.

DHCP Pool Size

Defines the maximum number of client devices that can connect to the network through the EVW3226.

Lease Time

Defines the lease time in seconds. A DHCP user’s PC gets an IP address with a lease time. When the lease time expires, the PC must connect to the DHCP server and be reissued the same or another IP address. The default lease time for the EVW3226 is 86400 seconds (24 hours).

System Time

System Time is provisioned by the ToD server. Before the gateway is online it will display a time counted from 1970-010100:00:00.

DNS Server 1 and DNS Server 2

Defines the DNS servers which are used for name to IP address resolution when, for example, browsing the Internet. By default these will be populated using the service provider defaults. A user can also configure some other DNS servers manually in this field.

Domain Name

Defines the domain name to be used by locally connected clients. For example: “local.loc.”

Save

Saves changes.

Ubee EVW322 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

31

Ubee Interactive

IPv6 Mode Screenshot:

Note: The label descriptions for the IPv4 Mode screenshot also apply to the IPv6 Mode screenshot. The IPv6 Address and Prefix are added at the top of the screen.

5.3

Using the DHCP Client Devices Option Use the DHCP Client Devices option to view devices connected to the EVW3226 via DHCP (dynamic host configuration protocol). Steps To view DHCP-connected devices: 1. Click Basic from the main menu. 2. Click DHCP Client Devices from the left side menu. Field descriptions are listed below the screen example.

32

Ubee EVW322 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

Ubee Interactive

Label

Description

MAC Address

Displays the hardware address of the connected device.

IP Address

Displays the IP address of the connected device.

Host Name

The host name for the connected device.

Expires On

Displays when the IP address expires.

Ubee EVW322 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

33

Ubee Interactive

34

Ubee EVW322 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

6

The Advanced Menu Advanced options provide settings to configure your gateway, such as MAC filtering and port forwarding. Topics See the following topics:

      

Using Using Using Using Using Using Using

the the the the the the the

Options Option on page 35 IP Filters Option on page 36 MAC Filters Option on page 38 Port Filters Option on page 39 Forwarding Option on page 40 Port Triggers Option on page 43 DMZ Host Option on page 45

Steps To access the advanced menu: 1. Click Advanced from the main menu.

6.1

Using the Options Option Use the Options option to configure router options. Steps To enable or disable network protocols: 1. Click Advanced from the main menu. 2. Click Options from the left side menu. Field descriptions are listed below the screen example.

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

35

Ubee Interactive

Label

6.2

Description

WAN Blocking

Blocks connection requests initialized from Internet users when enabled. WAN Blocking must be disabled to be able to PING the WAN gateway IP.

IPSec PassThrough

Enables support for IPSec in raw IP connection mode. Should normally be enabled.

PPTP PassThrough

Enables support for clients to establish PPTP (Point-to-Point Tunneling Protocol) VPN connections. Should normally be enabled.

Multicast

Optimizes the bandwidth utilization compared with unicast (especially video streaming applications).

UPnP

Activates Universal Plug and Play (UPnP) when enabled. A UPnP device can dynamically join a network, obtain an IP address, convey its capabilities, and learn about other devices on the network. In turn, a device can leave a network smoothly and automatically when it is no longer in use. Gaming consoles and Web cameras are examples of devices that can use UPnP. This should normally be enabled if gaming consoles or other UPnP enabled devices are located in the home network.

Save

Saves changes.

Using the IP Filters Option Use the IP Filters option to filter IP addresses. Any host on this list is not accessible to Internet traffic.

36

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

Ubee Interactive

Steps To filter IP addresses: 1. Make sure a PC is connected to the gateway and both devices are powered on and functioning. 2. Note the IP address of the devices that you want to deny Internet access. 3. After logging in to the gateway’s Web user interface, click Advanced from the main menu. 4. Click IP Filters from the left side menu. Field descriptions are listed below the screen example.

Label

Description

Start IP Address

Defines the starting IP address to filter.

End IP Address

Defines the ending IP address to filter.

Add Row

Allows additional IP Filters to be configured.

Save

Saves changes.

Note: To enter a single IP address, enter that IP address in both the start and end fields.

Note If the local host IP address is assigned through the build in the DHCP server (refer to Using the DHCP Client Devices Option on page 32), then the host IP may change. To avoid this you may also filter by the MAC address which does not require setting a static lease. Refer to Using the MAC Filters Option on page 38

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

37

Ubee Interactive

6.3

Using the MAC Filters Option The MAC Filters option allows you to filter MAC addresses to block traffic from specific network devices on the LAN to the Internet. MAC filtering establishes a list and any host on this list is not able to access the wide area network through the EVW3226. Steps To filter MAC addresses: 1. Note the MAC address of the devices that you want to deny Internet access. Note: Be sure all devices to which you potentially deny Internet access are connected to the EVW3226 network. 2. After logging in to the Web user interface, click Advanced from the main menu. 3. Click MAC Filters from the left side menu. 4. Enter the MAC address to block in the text box beneath the MAC Address label. 5. Click the Add MAC Address button. The MAC address is displayed in the filtered MAC address list. Field descriptions are listed below the screen example.

Label

Description

MAC Address

Defines the MAC address to block.

Add Row

Allows additional MAC Filters to be configured.

Save

Saves Changes

Note: The valid format for entering the MAC address is xx:yy:zz:aa:bb:cc.

38

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

Ubee Interactive

6.4

Using the Port Filters Option Use the Port Filters option to configure port filters to block to all devices on the LAN Internet services that use the ports specified. Steps To configure port filters: 1. Click Advanced from the main menu. 2. Click Port Filters from the left side menu. Field descriptions are listed below the screen example. For example: To prevent all Telnet access into and across your LAN: 1. Enter the Start and End ports to be 23. 2. Select Both for Protocol to include TCP and UDP. 3. Check Enabled. 4. Click Apply. Field descriptions are listed below the screen example. Caution Use caution when assigning port filtering by port range. You may accidentally prevent traffic that should pass through your network, such as http or email. Pre-assigned application ports are displayed on the Forwarding screen. Refer to Using the Forwarding Option on page 40.

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

39

Ubee Interactive

Label

Description

Filter Port Range

6.5

Defines the format of port numbers to be filtered. Options are: 1.

Single Port (entry format is “23”)

2.

Port Range (entry format is “23-25”)

Protocol

Selects the protocol type. Options are UDP, TCP, or BOTH.

Add Row

Allows additional Port Filters to be configured.

Save

Saves changes.

Using the Forwarding Option Forwarding tells the gateway to which computer on the local area network to send data. If your host systems or applications have communications issues with the Internet, you can use forwarding to resolve the following issues:  Data is sent from a local host to the Internet, but the return path of expected data is not received by your local host.  An application or service running on your local network (on local host) cannot be accessed from the Internet directly (for example, a request to a local audio server). Examples are:  Xbox/PlayStation – Games/applications  Home Security Systems – Security systems that use the Internet  Audio Servers/VoIP – Audio and VoIP applications and services Topics See the following topics:

 Before Setting Up Forwarding on page 40  Setting Up Port Forwarding on page 41  Setting Up Forwarding for an Xbox Example on page 42

6.5.1

Before Setting Up Forwarding Try the following options before you assign forwarding rules:  Enable Universal Plug and Play (UPnP). This may resolve the issue you have without setting up forwarding rules. Refer to Using the Options Option on page 35 for instructions to enable UPnP. Then test your local host or application such as your Xbox to see if it is functioning properly. Continue with port forwarding if the host or application is not communicating correctly.

 Assign a Static IP lease to the client/host to which you are setting up forwarding. This way, the IP does not change and disrupt your forwarding rules. For example, if you are hosting a Web server in your internal network and you wish to setup a forwarding rule for it, you should assign a static IP lease to that system to keep the IP from renewing and disrupting the forwarding rule. 40

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

Ubee Interactive

6.5.2

Setting Up Port Forwarding If the suggestions in Before Setting Up Forwarding on page 40 did not correct your communication problem, use port forwarding. You need the following information to set up forwarding:  IP address of each local host system (for example, Xbox) for which you need to setup a port forwarding rule.  Port numbers the local host’s application listens to for incoming requests/data (for example, a game or other service). These port numbers should be available in the documentation associated with the application. Note For detailed information on port forwarding, including how to set it up for specific applications using specific network devices (for example, cable modems), refer to: http://portforward.com or consult your host device or application user manual. Steps To set up forwarding: 1. Click Advanced from the main menu. 2. Click Forwarding from the left menu. 3. Enter information in the forwarding fields and click Add Row. 4. Click Save. The forwarding rule is created and displayed in the table. Field descriptions are listed below the screen example.

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

41

Ubee Interactive

Label Public Port Range

Description Defines the format of port numbers on the WAN side to be filtered. Options are: 1.

Single Port (entry format is “23”)

2.

Port Range (entry format is “23-25”)

Target IP Address

Defines the IP address of the local host system. Refer to Using the DHCP Client Devices Option on page 32 for information on how to find the IP address of a client.

Target Port Range

Defines the format of port numbers listened to by the server host located in your LAN. Options are: 1.

Single Port (entry format is “23”)

2.

Port Range (entry format is “23-25”)

Protocol

Selects the protocol type. Options are UDP, TCP, or Both.

Add Row

Allows additional forwarding to be configured.

Save

Saves changes.

Note: To enter a single IP address, enter that IP address in both the start and end fields.

6.5.3

Setting Up Forwarding for an Xbox Example Following is an example of how you would set up a single Xbox running Modern Warfare 2. Since multiple ports are used for the Xbox and the Modern Warfare 2 game, a separate forwarding rule is set for each port. Multiple ports and forwarding rules may not be required for other applications. Steps To set up port forwarding for an Xbox: 1. Click Advanced from the main menu. 2. Click Forwarding from the left side menu. 3. Enter the Xbox IP address in the Target IP Address field. 4. Define ports used by the Xbox in the Public Port Range field. Define the same ports used by the Xbox in the Target Port Range field. 5. Create Port Forwarding rules per port. A rule set up for port 53 works for port 53. A port can be used only by one program at a time.

42

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

Ubee Interactive

Note You can set up applications/services to listen on one internal port. External Internet users who want to access that application, address it using an external port, such as an Audio server. Internal Ports are the ports to which local servers listen. External Ports are the ports that the gateway listens to from the WAN.

6.6

Using the Port Triggers Option Port Triggers define dynamic triggers to specific devices on the LAN. This allows special applications that require specific port numbers with bi-directional traffic to function properly. Applications such as video conferencing, voice, gaming, and some messaging program features may require these special settings. Some services use a dedicated range of ports on the client side and a dedicated range of ports on the server side. The difference between port forwarding and triggering is:  Port forwarding sets a rule to send a service to a single LAN IP address.  Port triggering defines two kinds of ports: trigger port and target port. The trigger port sends a service request from a LAN host to a specific destination port number. The port the LAN host is required to listen to by the application is called the target port. The server returns responses to these ports. For example: 1. John requests a file from the Real Audio server (port 7070). Port 7070 is a “trigger” port and causes the device to record John’s computer IP address. The EVW3226 associates John's computer IP address with the “target” port range of 6970-7170. 2. The Real Audio server responds to a port number ranging between 6970-7170. 3. The EVW3226 forwards the traffic to John’s computer IP address. 4. Only John can connect to the Real Audio server until the connection is closed or expires.

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

43

Ubee Interactive

Steps To set up port triggering: 1. Click Advanced from the main menu. 2. Click Port Triggers from the left side menu. 3. Enter information in the trigger fields and click Add Row. 4. Click Save. The port trigger rule is created and displayed in the table. Field descriptions are listed below the screen example. Note The following example shows the Port Triggering option set up for a dual Xbox configuration.

44

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

Ubee Interactive

Label Trigger Port Range

Target Port Range

Description Defines the range of ports that trigger the router to record the IP address of the LAN computer that sent the traffic to a server on a LAN. Options are: 1.

Single Port (entry format is “23”)

2.

Port Range (entry format is “23-25”)

Defines a target range of ports a server on the WAN uses when it responds to service requests. The router forwards the traffic with this port (or range of ports) to the client computer on the LAN that requested the service. Options are: 1.

Single Port (entry format is “23”)

2.

Port Range (entry format is “23-25”)

Protocol

Defines the protocol type for this rule, UDP, TCP, or Both.

Add Row

Allows additional port triggers to be configured.

Save

Saves changes.

Note: To enter a single IP address, enter that IP address in both the start and end fields.

6.7

Using the DMZ Host Option Use the DMZ (De-Militarized Zone) Host option to expose a host IP address to the WAN (public Internet). You can use this option when applications do not work with port triggers or other networking strategies. Steps To set up a DMZ host: 1. Connect a PC to an Ethernet port on the EVW3226. Make sure both devices are powered on and functioning. 2. Connect a client device, such as a PC, that you wish to be in the DMZ to an Ethernet port on the EVW3226 or via WLAN. 3. After logging in to the Web user interface, click Advanced from the main menu. 4. Click DMZ Host from the left side menu. 5. Test the device to ensure Internet access is available and the device is functional. For example, connect to the Internet from a PC connected to the Home Gateway, or make calls from a VoIP phone.

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

45

Ubee Interactive

Label

Description

IP Address

Defines the IP address of the host to be exposed.

Save

Saves changes.

Note: Any host exposed in this way will be fully reachable from the Internet and is not protected by the gateway and firewall functions of the EVW3226.

6.8

Using the Firewall Option Use the Firewall option to configure what types of traffic are allowed onto your network. It is highly recommended the Firewall is left enabled at all times. Refer to Using the Web Site Filters Option on page 52 to block Internet access to specific sites. Steps To configure firewall settings: 6. Click Advanced from the main menu. 7. Click Firewall from the left side menu. Field descriptions are listed below the screen example.

46

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

Ubee Interactive

Label

Description

Port Scan Detection

Detects port scan attacks.

IP Flood Detection

Detects IP flood attacks.

IPv4 Firewall Protection

Activates the IPv4 firewall function.

IPv6 Firewall Protection

Activates the IPv6 firewall function.

Save

Saves changes.

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

47

Ubee Interactive

48

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

7

The Parental Control Menu Parental Controls allow you to control Internet access for users on the EVW3226 network. Parental Controls provides the following features:    

Define user/password access. Block specific Web sites and Web sites based on keywords. Define the times users are allowed to access the Internet. View an event log to view Internet activity.

Topics See the following topics:

   

Using Using Using Using

the the the the

Parental Control Device Rules Option on page 49 Basic Setup Option on page 50 Web Site Filters Option on page 52 TOD Filters Option on page 53

Steps To access the parental control menu: 1. Click the Parental Control link from the main menu.

7.1

Using the Parental Control Device Rules Option The Device Rules option allows you to configure which user accounts can or cannot connect to your wireless or wired network, and the parameters of each connection. Steps To configure user accounts: 1. Click the Parental Control link from the main menu. 2. Click Device Rules from the left side of the screen. The Device Rules fields are explained following the screen example.

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

49

Ubee Interactive

Label

Description

Add a Device

Click the “Add a Device” button to add parental controls for a client device. Enter the appropriate information in the

Add a Device PoP-Up Window

7.2

Device Name

Enter the name of the device for parental controls to be enabled.

MAC Address

Enter the MAC address of the device for parental controls to be enabled.

Cancel

Cancel adding the device.

Add Device

Click Add Device to add the device.

Device Name

Displays the name of the device with parental controls enabled.

MAC Address

Displays the MAC address of the device with parental controls enabled.

Web Site Filters

Displays the web site filters.

ToD Filters

Displays the ToD filters.

Save

Saves all changes when clicked.

Using the Basic Setup Option The Basic Setup option allows you to select rules to block certain Internet content and Web sites. After you change your Parental Control settings, click the appropriate Apply, Add, or Remove button for your new settings to take effect. Refresh your browser’s display to see the currently active settings.

50

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

Ubee Interactive

Steps To filter Internet content and Web sites: 1. Click the Parental Control link from the main menu. 2. Click Basic Setup from the left side of the screen. The Basic Setup fields are explained following this screen example.

Label

Description

Enable Parental Control

Activates the Parental Control feature when Enabled is selected.

Password

Defines the password.

Retype Password

Checks the password with the re-entered password.

Access Duration

The access duration time in minutes.

Enable Override Password

Enables an override password for the filter settings

Trusted Computers MAC Address

Enter the MAC address of the trusted computer.

Add to Trusted Computers

Click “Add to Trusted Computers” to add the computer.

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

51

Ubee Interactive

Label

Description

Trusted Computers

Displays the trusted computers.

Remove Selected

Allows you to select and remove a device from the Trusted Computers list.

Save

7.3

Saves all changes in the screen and activates Parental Control, if enabled.

Using the Web Site Filters Option The Web Site Filters option allows you to configure which web sites can be reached from the device. Steps To configure web site filters: 1. Click the Parental Control link from the main menu. 2. Click Web Site Filters from the left side of the screen. The Web Site Filters fields are explained following this screen example.

Label

Description

Policies

Lists the existing policies in a drop-down list.

Remove Current Policy

Deletes a policy. Select the policy from the drop-down list and click Remove.

Add New Policy

Click the Add New Policy button to add a new policy.

Add a Policy Pop-Up WIndow

52

Policy Name

Enter the name of the policy to be added.

Cancel

Click Cancel to cancel the addition of the new policy.

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

Ubee Interactive

Label Create

7.4

Description Click Create to add the new policy.

Keywords

Enables you to add keywords in order to block web site addresses (URLs) containing those words.

Mode Select

Select the mode for the new policy, Allowed or Blocked.

Domains

Allows you to create a list of domains either to be allowed or blocked according to the selected mode.

Clear

Clears the information entered on the screen.

Submit

Saves all changes when clicked.

Using the TOD Filters Option The TOD Filters option allows the configuration of time-based access policies, which block all Internet traffic at specified times. Steps To configure the TOD Filters policy: 1. Click the Parental Control link from the main menu. 2. Click TOD Filters from the left side of the screen. The TOD Filters fields are explained following this screen example.

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

53

Ubee Interactive

Label

Description

Policies

Lists the existing TOD filter policies in a drop-down list.

Remove

Deletes a policy. Select the policy from the drop-down list and click the Remove button.

Add

Adds a new policy. Enter a policy name and click the Add button. The Add a Policy window pops up.

Add a Policy Pop-Up Window

54

Policy Name

Allows you to enter the policy name.

Cancel

Click Cancel to cancel the addition of the policy.

Create

Click Create to create the policy.

Hour/Day of the Week

Enables you to select specific days of the week and hours in the day to block Internet access for the policy.

Clear

To empty the displayed log entries, click Clear.

Inverse

Inverse the selected hour/day.

Blocked

Blocked hours of each day are highlighted in blue.

Submit

Saves the changes.

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

8

The Wireless Menu Use the Wireless menu to configure a wireless network. There are configuration options for 2.4 GHz and 5 GHz bands. Please note that only one band can be active at a time. The screenshots for the Security, Advanced, Access Control and WPS options are the same for both the 2.4 and 5 GHz bands. Details for the 2.4 GHz band screenshots will be shown. Topics See the following topics:

     

Using the Wireless Radio Option on page 55 Using the Security Option on page 57 Using the Advanced Option on page 61 Using the Access Control Option on page 63 Using the WPS Option on page 64 Deploying and Troubleshooting the Wireless Network on page 65

Steps To access the wireless menu: 1. Click Wireless from the main menu.

8.1

Using the Wireless Radio Option The Radio option is used to configure the wireless radio, including channel number, and bandwidth control. Use the Radio option to enable either the 2.4 GHz or the 5 GHz band. Only one can be active at a time. Steps To configure wireless operations: 1. Click Wireless from the main menu. 2. Click Radio from the left side menu under either the 2.4 GHz or 5 GHz band option. Field descriptions are listed below the screen examples.

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

55

Ubee Interactive

Screenshot for Mixed (802.11b, 802.11g and 802.11n) mode

Label

Description

Enable

Allows you to select the wireless radio’s status, Enabled or Disabled.

SSID

Defines the gateway’s SSID (service set identifier), which is the public name of the wireless network.

802.11 Mode

Allows you to choose the network mode option. Options are: 1.

Mixed (802.11b, 802.11g and 802.11n)

2.

802.11b

3. 802.11g In 5 GHz mode the network mode options are:

56

1.

Mixed (802.11a and 802.11n)

2.

802.11a

Channel

Allows you to select one of the channels from the drop-down list to correspond with your network settings. All devices in your wireless network must broadcast on the same channel in order to communicate. You can select Auto for automatic channel selection.

Bandwidth

Choose between the following channel options: 1.

20Mhz

2.

40Mhz

Power

Sets the percent of the output power for the radio.

Save

Saves changes.

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

Ubee Interactive

Screenshot for 802.11b and 802.11g modes

Note that there is no Bandwidth field for 802.11g and 802.11b. The channel bandwidth for these modes is 20 MHz. The same applies for 802.11a in the 5 GHz band.

8.2

Using the Security Option The security option allows you to configure a variety of wireless security settings. Steps To access the wireless security option: 1. Click Wireless from the main menu. 2. Click Security from the left side menu under either the 2.4 GHz or 5 GHz band option. Security mode options include: NONE WEP WPA-Personal WPA-Enterprise 3.

Field descriptions are listed below the screen example for each security mode option.

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

57

Ubee Interactive

NONE selected for security mode

WEP security mode

58

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

Ubee Interactive

Label Wireless Security Mode

Description Defines the wireless security mode. Note that WEP (Wired Equivalent Privacy) cannot be selected when the 802.11 mode is configured in Mixed. WEP is only applicable in 802.11b or 802.11g mode. It is recommended to avoid the use of WEP whenever possible due to known security issues with this standard.

WEP Authentication

WEP Encryption

Defines the authentication method. Options are: 1.

Automatic

2.

Shared Key

Defines the WEP encryption. Options are: 1.

WEP 64-bit

2.

WEP 128-bit

WEP Passphrase

Choose a wireless passphrase (between 8 and 63 characters) and enter it here.

Generate

Click generate to create the network keys.

Key 1 - Key 4

Select which WEP key (1-4) will be used as the default transmit key. The receiving device must use the same key. If you want to manually enter WEP keys instead of using a passphrase, complete the fields provided. 64-bit keys require 10 digits, 128-bit keys require 26 digits. Digits are in hexadecimal format using the letters A through F and the numbers 0 through 9.

Save

Saves changes.

WPA (Wi-Fi Protected Access) -Personal security mode

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

59

Ubee Interactive

Label

Description

Wireless Security Mode

Defines the wireless security mode.

Authentication

Defines the authentication method. Options are:

Encryption

1.

WPA

2.

WPA2

3.

WPA/WPA2

Defines the encryption algorithm. Options are: 1.

AES (Advanced Encryption Standard)

2.

TKIP (Temporary Key Integrity Protocol)

3. AES+TKIP Note that TKIP cannot be selected when the 802.11 mode is configured in Mixed. It is only applicable in 802.11b or 802.11g mode. Key Interval

Enter a Key renewal interval (in seconds), which instructs the gateway how often it should change encryption keys.

Passphrase

Enter the passphrase (also referred to as the pre-shared key, password, or network key). The passphrase is printed on the product label. For more information, refer to Default Values and Logins on page 9

Retype Passphrase

Re-enter the passphrase for verification.

Save

Saves changes.

WPA-Enterprise security mode

60

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

Ubee Interactive

Label

Description

Wireless Security Mode

Defines the wireless security mode.

Authentication

Defines the authentication method. Options are:

Encryption

1.

WPA

2.

WPA2

3.

WPA/WPA2

Defines the encryption algorithm. Options are: 1.

AES

2.

TKIP

3. AES+TKIP Note that TKIP cannot be selected when the 802.11 mode is configured in Mixed. It is only applicable in 802.11b or 802.11g mode. Key Interval

Enter a Key renewal interval (in seconds), which instructs the gateway how often it should change encryption keys.

Radius Server

8.3

IP Address

Enter the radius server’s IP address.

Port

Enter the port number on the radius server.

Shared Secret Key

Enter the shared secret key used by the gateway and the radius server.

Retype Shared Secret Key

Re-enter the shared secret key for verification.

Save

Saves changes.

Using the Advanced Option The advanced wireless settings allow you to configure the advanced WLAN settings of the wireless network for your EVW3226. This section is used to configure advanced wireless functions. Steps To access the advanced wireless security option: 1. Click Wireless from the main menu. 2. Click Advanced from the left side menu under either the 2.4 GHz or 5 GHz band option. Field descriptions are listed below the screen example.

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

61

Ubee Interactive

Label

62

Description

MAC Address

Displays the MAC address of the gateway.

Beacon Interval

The Beacon Interval value indicates the frequency interval of the beacon. A beacon is a packet broadcast by the gateway to synchronize the wireless network. The default value is 100.

DTIM Interval

Specifies the DTIM interval from 1 to 255ms. This value indicates how often the gateway sends out a Delivery Traffic Indication Message (DTIM). Lower settings result in more efficient networking, preventing your wireless clients from dropping into power-saving sleep mode. Higher settings allow your wireless clients to enter sleep mode, thus saving power, but interferes with wireless transmissions. The default value is 1.

Fragment Threshold

Specifies the fragmentation threshold packet size between 256-2346 bytes. Fragmentation takes place when a packet’s size exceeds the fragmentation threshold. The default setting is 2346.

RTS Threshold

The RTS Threshold sets the packet size limit. When the threshold is passed, the ready to send/clear (RTS/CTS) function is invoked. The allowable setting range is from 1 to 2347 bytes. The default setting is 2347 bytes.

AMPDU

Allows you to set the AMPDU status to Enabled or Disabled. AMPDU (MAC Protocol Data Unit Aggregation) packages multiple MPDUs together to reduce overhead. The default value is enabled.

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

Ubee Interactive

Label

Description

WMM

Allows you to set the WMM status to Enabled or Disabled. If WMM (WiFi Multimedia) is enabled, voice and multimedia traffic will be given higher priority than other traffic. The default setting is enabled.

WMM Power Save

Allows you to enable or disable WMM power save mode. The default setting is enabled.

Save

Saves changes.

Note: It is generally recommended that you keep all the default settings in this setup page. Changes may adversely affect performance or WLAN stability. To reset to default values you may perform a factory default. Refer to Using the Factory Default Option on page 73

8.4

Using the Access Control Option Use the Access Control option to configure which client devices can access your wireless network. Steps To configure wireless access control options: 1. Click Wireless from the main menu. 2. Click Access Control from the left side menu under either the 2.4 GHz or 5 GHz band option. Field descriptions are listed below the screen example.

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

63

Ubee Interactive

Label

Description

Policy

8.5

Enables you to select an access control policy. Options are: 1.

None

2.

Allow List

3.

Deny List

MAC Address

Allows you to enter the MAC addresses of the devices for which you want to control access.

Add Row

Allows additional MAC addresses to be entered.

Save

Saves changes.

Using the WPS Option WPS (WiFi Protected Setup) is a standard method for easily configuring a secure connection between your EVW3226 and computers or other wireless devices (clients) that support WPS. When WPS is enabled, you can attach other wireless devices by pressing the WPS PBC (push button control) on the device (if equipped) and on your EVW3226, or by entering the wireless device’s WPS PIN and then clicking the “PIN START” button. Steps To configure the WPS options: 1. Click Wireless from the main menu. 2. Click WPS from the left side menu under the 2.4 GHz band option. Field descriptions are listed below the screen example.

64

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

Ubee Interactive

Label

8.6

Description

WPS

Enables you to set the WPS status, Enabled or Disabled.

PIN

If the client you wish to connect to has a WPS PIN (personal identification number), enter the number here and click the PIN START button. The client’s PIN can be found in the client’s WPS Setup utility.

PBC

If the client you wish to connect to has a WPS PBC (push button control), click the PBC START button on the WPS screen or push the WPS button on your EVW3226. Refer to EVW3226 Front Panel on page 6 for the location of the EVW3226’s WPS button. Push the WPS button on the client device at the same time. The connection will automatically set up.

Save

Saves changes.

Deploying and Troubleshooting the Wireless Network Use the information in this section to help you understand, deploy, and troubleshoot your wireless environments:  Understanding Received Signal Strength on page 65  Estimating Wireless Gateway to Wireless Client Distances on page 65  Selecting a Wireless Channel on page 67 Understanding Received Signal Strength Received signal strength (RSSI) is measured from connected wireless client devices to the wireless gateway and vice versa. This value can significantly impact wireless speeds/performance. It is determined by:  Materials (for example, open air, concrete, trees)  Distance between wireless clients and the wireless gateway  Wireless capabilities of the client devices Estimating Wireless Gateway to Wireless Client Distances The information in this section helps you to determine how far a wireless gateway can be placed from wireless client devices. Environmental variances include the capabilities of wireless clients and the types of material through which the wireless signal must pass. When the wireless gateway and wireless clients reach the distance threshold between each other, network performance degrades.

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

65

Ubee Interactive

Steps To determine wireless gateway placement: 1. Connect a wireless client to the wireless gateway. Refer to Connecting Devices to the Network on page 13 if needed. 2. Place the wireless client at around one meter away from the wireless gateway. 3. Use the following table to determine what materials the wireless signal must travel through to reach the desired wireless coverage distance. Attenuation Considerations at 2.4GHz

Material

Attenuation

Connector/Cable

3.5dB

Free Space

.24dB / foot

Interior Drywall

3dB to 4dB

Cubicle Wall

2dB to 5dB

Wood Door (Hollow/Solid)

3dB to 4dB

Brick, Concrete Wall (Note 1)

6dB to 18db

Glass Window (not tinted)

2dB to 3dB

Double Pane Coated Glass

13dB

Bullet Proof Glass

10dB

Steel / Fire Exit Door

13dB to 19dB

Human Body

3dB

Trees (Note 2)

.15dB / foot

Note 1: Different types of concrete materials are used in different parts of the world and the thickness and coating differ depending on whether it is used in floors, interior walls, or exterior walls.

Note 2: The attenuation caused by trees varies significantly depending upon the shape and thickness of the foliage.

4. To check the wireless signal strength and speed, use the following steps for a computer running Windows 7 connected wirelessly to the wireless gateway. If the wireless computer is not connected, refer to Connecting a Wireless Device on page 14. a. Double-click the Wireless networking icon on your Windows 7 task bar. .

b. Windows will show the word “Connected” next to the name of the current wireless network. Right click on it and choose “status” from the menu.

66

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

Ubee Interactive

c.

Review the speed and signal strength in the Wireless Network Connection Status window.

Selecting a Wireless Channel You may need to change the wireless channel on which the wireless gateway operates when you are in computing, test, and other environments where several wireless access points may be operating in the 2.4Ghz range. In some cases, you may want to segment your wireless traffic where a group of devices operates on one channel and another group operates on another channel, and so on. This is done by configuring the channel on each wireless access point individually (if you have multiples). If you have control over only one wireless device in an environment where there may be several, you can change the wireless channel on your gateway to one that is not heavily used. Note To change the wireless broadcast channel, refer to Using the Wireless Radio Option on page 55.

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

67

Ubee Interactive

The following diagram displays the 2.4 GHz channels available in Europe. Each available channel is 22Mhz wide. Since channels overlap, it is best to choose channels that have the least overlap (typically 1, 5, 9, and 13 in Europe). Overlapping channels can cause wireless network performance issues.

Source: Wikipedia.org, and IEEE article IEEE 802.11n-2009

68

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

9

The System Menu Use the System menu to change the user password, select the router mode, backup and restore EVW3226 configuration settings, and configure remote and local logging. Topics See the following topics:

   

Using Using Using Using

the the the the

Password Option on page 69 Switch Mode Option on page 70 Backup and Recovery Option on page 71 Log Option on page 74

Steps To access the system menu: 1. Click System from the main menu.

9.1

Using the Password Option The Password option allows the user password to be changed. Steps To change the user password: 1. Click System from the main menu. 2. Click Password from the left side menu. Field descriptions are listed below the screen example.

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

69

Ubee Interactive

Label

9.2

Description

Old Password

Enter the old user password.

New Password

Allows you to enter a new password for the user account.

Retype New Password

Re-enter the password for confirmation.

Save

Saves changes.

Using the Switch Mode Option The Switch Mode option allows you to select the mode for the router. The switch mode page will only be visible when it is enabled by your cable operator. By default it is configured as a router, providing the normal functions of a typical home gateway with firewall protection and network address translation. In some cases a user may want to configure the gateway to act as a bridge. For example, to enable the use of a subscriber’s own router or firewall device. In such cases the configuration can be changed in the menu as explained below. Steps To select the mode for the router: 1. Click System from the main menu. 2. Click Switch Mode from the left side menu. Field descriptions are listed below the screen example.

70

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

Ubee Interactive

Label Switch Mode

Save

9.3

Description Specify the router mode. Options are: 1.

Router Mode

2.

Bridge Mode

Saves the changes.

Using the Backup and Recovery Option The Backup and Recovery option allows backup of the EVW3226’s current configuration, restoration to a previously saved configuration, or restoration to the factory default settings. Topics See the following topics:

 Using the Backup Option on page 71  Using the Restore Option on page 72  Using the Factory Default Option on page 73

9.3.1

Using the Backup Option Steps To backup your gateway’s current configuration settings: 1. Click System from the main menu. 2. Click Backup from the left side menu. Field descriptions are listed below the screen example.

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

71

Ubee Interactive

Label

9.3.2

Description

Password

Specify your password if you want to encrypt your configuration’s backup. Leave it blank for no encryption.

Repeat Password

Re-enter the password for confirmation.

Backup

Click the Backup button to begin the backup process.

Using the Restore Option Steps To restore your gateway’s configuration to a previously saved setting: 1. Click System from the main menu. 2. Click Restore from the left side menu. Field descriptions are listed below the screen example.

72

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

Ubee Interactive

Label

9.3.3

Description

Password

Specify your password if you want to restore your previously saved encrypted configuration.

Select File

Click the Browse button to locate and select the previously saved configuration.

Restore

Click the RESTORE button to restore the previously saved configuration.

Using the Factory Default Option Steps To restore your gateway’s configuration to the factory default settings: 1. Click System from the main menu. 2. Click Factory Default from the left side menu. Field descriptions are listed below the screen example.

Label Restore Defaults

Description Click the Restore Defaults button to restore the factory default settings.

Note: All customized settings will be lost and reverted to factory defaults. Make sure you save or write down your configuration for later use. You can also restore factory defaults by pressing the RESET button on the back of the EVW3226. Use a pointed object to push down the reset button for 5-10 seconds until the power LED turns off. After the power LED turns off, release the button. If the Reset button is pressed for less than 5 seconds, it will cause the gateway to reboot.

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

73

Ubee Interactive

9.4

Using the Log Option The Log option allows you to configure remote and local logging.  Using the Syslog Option on page 74  Using the Local Log Option on page 75

9.4.1

Using the Syslog Option The Syslog page allows you to set up remote logging by specifying the IP address where a SysLog server is located and select different types of events that may occur. Then each time such an event occurs, notification is automatically sent to the log server. Steps To set up remote logging: 1. Click System from the main menu. 2. Click Syslog from the left side menu. Field descriptions are listed below the screen example.

Label

74

Description

Remote Logging

Enables or Disables remote logging.

Level

Allows you to select the level(s) of events to be sent to the log server.

Module

Allows you to select the module(s) of events to be sent to the log server.

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

Ubee Interactive

Label

9.4.2

Description

Log Server IP Address

Specify the IP address of the log server.

Port

Displays the port of the log server.

Save

Saves changes.

Using the Local Log Option The Local Log page allows you to configure local logging by selecting different types of events that may occur. Then each time such an event occurs, a log message is recorded locally and displayed in the web UI. Steps To configure local logging: 1. Click System from the main menu. 2. Click Local Log from the left side menu. Field descriptions are listed below the screen example.

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

75

Ubee Interactive

Label

76

Description

Level

Allows you to select the level(s) of events to be sent to the log server.

Module

Allows you to select the module(s) of events to be sent to the log server.

Refresh

Updates the log list.

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

10

The WIFI4ALL Menu WIFI4ALL is an option provided by your service provider to enable your gateway to also act as a public hotspot. This page will only be displayed when WIFI4ALL service is enabled by your service provider. For further information contact your service provider. Steps To access the WIFI4ALL option: 1. Click WIFI4ALL from the main menu. The WIFI4ALL page will only be displayed when WIFI4ALL service is enabled. Field descriptions are listed below the screen example.

Label

Description

MAC Address

Displays the MAC address of the WIFI4ALL network.

Mode

Displays the current WIFI4ALL network mode.

Channel Width

Displays the current channel bandwidth of the WIFI4ALL network.

Channel

Displays the current broadcast channel of the WIFI4ALL network.

Security Mode

Displays the current wireless security mode of the WIFI4ALL network.

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

77

Ubee Interactive

Label

78

Description

Network Name (SSID)

Displays the public name of the WIFI4ALL network.

SSID Broadcast

Displays whether SSID broadcast is enabled or disabled on the WIFI4ALL network.

Number of Devices Connected

Displays the number of devices wirelessly connected to the WIFI4ALL network.

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

Ubee Interactive

11

The DSLite Menu Through DSLite, your service provider allows you to take part in the next generation Internet protocol called IPv6, while maintaining backward compliance to the widely used IPv4 protocol. This page will only be displayed when the EVW3226 is provisioned in IPv6 router mode. The feature is automatically configured by your service provider and needs no user configuration. For further information contact your service provider. Steps To access the DSLite option: 1. Click DSLite from the main menu. Field descriptions are listed below the screen example.

Label

Description

AFTR Domain Name

Displays the full qualified domain name (FQDN) of the provisioned AFTR.

AFTR IPv6 Address

Displays the IPv6 address of the provisioned AFTR.

Status

Displays the status of the DS-Lite service (Active or Inactive).

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013

79

Ubee Interactive

Ubee Interactive Europe Beech Avenue 54-80 1119 PW Schiphol Rijk The Netherlands www.ubeeinteractive.com Sales (email): [email protected] Support (email) [email protected] This document includes various trademarks of Ubee Interactive. Product and service availability are subject to change without notice.

2013Ubee Interactive. All rights reserved. March 2013 Part number EVW3226

80

Ubee EVW3226 Advanced Wireless Voice Gateway Subscriber User Guide • March 2013