Download TM-1002 AVEVA Plant (12 Series) Drawing Production (Basic) Rev 2.0...
Drawing Production (Basic)
TM-1002
TRAINING GUIDE
AVEVA Plant (12 Series)
www.aveva.com
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
www.aveva.com 2
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Revision Log Date 24/01/2008 01/02/2008 04/03/2008 04/01/2009 04/01/2009 04/01/2009
Revision 0.1 0.2 1.0 1.1 1.2 2.0
Description of Revision Issued for Review Reviewed Approved for Training 12.0.0.3 Issued for Review Reviewed Approved for Training 12.0.SP3
Author IMP IMP IMP BT BT BT
Reviewed
Approved
BG / ED BG
RP
BG BG
RP
Updates All headings containing updated or new material will be highlighted.
Suggestion / Problems If you have a suggestion about this manual or the system to which it refers please report it to the AVEVA Group Solutions Centre at
[email protected]
This manual provides documentation relating to products to which you may not have access or which may not be licensed to you. For further information on which products are licensed to you please refer to your licence conditions.
Visit our website at http://www.aveva.com
Disclaimer Information of a technical nature, and particulars of the product and its use, is given by AVEVA Solutions Ltd and its subsidiaries without warranty. AVEVA Solutions Ltd. and its subsidiaries disclaim any and all warranties and conditions, expressed or implied, to the fullest extent permitted by law. Neither the author nor AVEVA Solutions Ltd or any of its subsidiaries shall be liable to any person or entity for any actions, claims, loss or damage arising from the use or possession of any information, particulars or errors in this publication, or any incorrect use of the product, whatsoever.
Trademarks AVEVA and Tribon are registered trademarks of AVEVA Solutions Ltd or its subsidiaries. Unauthorised use of the AVEVA or Tribon trademarks is strictly forbidden. AVEVA product names are trademarks or registered trademarks of AVEVA Solutions Ltd or its subsidiaries, registered in the UK, Europe and other countries (worldwide). The copyright, trademark rights or other intellectual property rights in any other product, its name or logo belongs to its respective owner.
www.aveva.com 3
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Copyright Copyright and all other intellectual property rights in this manual and the associated software, and every part of it (including source code, object code, any data contained in it, the manual and any other documentation supplied with it) belongs to AVEVA Solutions Ltd. or its subsidiaries. All other rights are reserved to AVEVA Solutions Ltd and its subsidiaries. The information contained in this document is commercially sensitive, and shall not be copied, reproduced, stored in a retrieval system, or transmitted without the prior written permission of AVEVA Solutions Limited. Where such permission is granted, it expressly requires that this Disclaimer and Copyright notice is prominently displayed at the beginning of every copy that is made. The manual and associated documentation may not be adapted, reproduced, or copied in any material or electronic form without the prior written permission of AVEVA Solutions Ltd. The user may also not reverse engineer, decompile, copy or adapt the associated software. Neither the whole nor part of the product described in this publication may be incorporated into any third-party software, product, machine or system without the prior written permission of AVEVA Solutions Limited or save as permitted by law. Any such unauthorised action is strictly prohibited and may give rise to civil liabilities and criminal prosecution.
The AVEVA products described in this guide are to be installed and operated strictly in accordance with the terms and conditions of the respective licence agreements, and in accordance with the relevant User Documentation. Unauthorised or unlicensed use of the product is strictly prohibited.
Printed by AVEVA Solutions on 03 March 2009 © AVEVA Solutions and its subsidiaries 2001 – 2007 AVEVA Solutions Ltd, High Cross, Madingley Road, Cambridge, CB3 0HB, United Kingdom.
www.aveva.com 4
Contents 1
Introduction .............................................................................................................................................. 9 1.1 Aim................................................................................................................................................... 9 1.2 Objectives ....................................................................................................................................... 9 1.3 Prerequisites................................................................................................................................... 9 1.4 Course Structure ............................................................................................................................ 9 1.5 Using this guide ............................................................................................................................. 9 2 DRAFT features...................................................................................................................................... 11 3 Getting started ....................................................................................................................................... 13 3.1 Entering a DRAFT Session.......................................................................................................... 13 3.2 Current Element Definition.......................................................................................................... 14 3.3 Displaying the Explorer windows............................................................................................... 14 3.4 Displaying Toolbars ..................................................................................................................... 14 3.5 Displaying the Draft Drawing Sheet ........................................................................................... 15 3.6 Using the mouse and keyboard to manipulate the view of the sheet..................................... 16 3.6.1 Mouse buttons ........................................................................................................................... 16 3.6.2 Keyboard Commands (Zooming and Panning) ......................................................................... 17 3.7 Resetting the Draft View .............................................................................................................. 18 3.8 Grid ................................................................................................................................................ 18 3.8.1 Displaying and Hiding the Draft Grid ......................................................................................... 18 3.8.2 Changing the Grid Spacing........................................................................................................ 19 3.8.3 Positioning Elements on a Grid (Snap)...................................................................................... 19 3.9 Saving and Restoring Views ....................................................................................................... 19 3.10 Settings User Defaults ................................................................................................................. 20 Exercise 1 - Viewing Controls ...................................................................................................................... 21 4 The PDMS DRAFT database hierarchy ................................................................................................ 23 4.1 DRAFT database hierarchy ......................................................................................................... 23 4.2 Creating the DRAFT hierarchy.................................................................................................... 24 4.2.1 Creating a DEPT (Department) ................................................................................................. 24 4.2.2 Creating a REGI (Registry) ........................................................................................................ 25 4.3 DEPT and REGI attributes ........................................................................................................... 25 4.3.1 Size and Units............................................................................................................................ 25 4.3.2 Intelligent Text............................................................................................................................ 27 4.3.3 Pens (and Fonts) ....................................................................................................................... 27 4.3.4 Miscellaneous ............................................................................................................................ 29 Exercise 2 - Create the DRAFT hierarchy ................................................................................................... 30 5 Creating Drawings and sheets ............................................................................................................. 31 5.1 Creating Drawings and Sheets ................................................................................................... 31 5.1.1 Creating Drawings from a Template .......................................................................................... 31 5.1.2 Creating Drawings from a Default Template.............................................................................. 33 5.1.3 Creating Drawings explicitly....................................................................................................... 34 5.1.4 Creating Drawing Sheets explicitly ............................................................................................ 35 Exercise 3 - Create a drawing from a template........................................................................................... 36 Exercise 4 - Create a drawing explicitly ...................................................................................................... 36 6 Creation and modification of Views..................................................................................................... 37 6.1 User defined view......................................................................................................................... 37 6.2 Creation of user defined VIEW.................................................................................................... 37 6.2.1 User Defined View (Frame menu) ............................................................................................. 37 6.2.2 User Defined View (View menu)................................................................................................ 40 6.2.3 User Defined View (Graphics menu) ......................................................................................... 41 6.2.4 User Defined View (General) ..................................................................................................... 44 6.2.5 User Defined View (Scale)......................................................................................................... 46 6.2.6 User Defined View (Intelligent text) ........................................................................................... 47 6.2.7 User Defined View (Attributes) .................................................................................................. 47 6.2.8 User Defined View (Change Highlighting) ................................................................................. 48 6.2.9 User Defined View (Update Design on Apply)........................................................................... 48 6.2.10 Creating local rules................................................................................................................ 49 Exercise 5 – Creating a User Defined View (Equipment arrangement).................................................... 50
www.aveva.com 5
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002 Exercise 6 – Creating a User Defined View (Piping arrangement) ........................................................... 52 6.3 Limits defined view ...................................................................................................................... 54 6.4 Creation of limits defined VIEW.................................................................................................. 54 6.4.1 Limits Defined View (General Menu) ......................................................................................... 54 6.4.2 Limits Defined View (Limits Menu) ............................................................................................ 55 6.4.3 Limits Defined View (Limits)....................................................................................................... 55 6.4.4 Limits Defined View (Scale) ....................................................................................................... 56 6.4.5 Limits Defined View (Matchlines)............................................................................................... 58 6.4.6 User Defined View (Update Design on Apply)........................................................................... 58 Exercise 7 – Creating a Limits Defined View (Equipment Arrangement) ................................................ 59 Exercise 8 - Creating a Limits Defined View (Structural Arrangement)................................................... 61 6.5 Creating views with predefined frames ..................................................................................... 63 6.5.1 Predefined frames...................................................................................................................... 63 Exercise 9 – Creating Predefined Views ..................................................................................................... 64 7 Dimensioning ......................................................................................................................................... 67 7.1 Dimension Hierarchy ................................................................................................................... 67 7.2 Dimension Types.......................................................................................................................... 67 7.3 Linear Dimensions ....................................................................................................................... 68 7.3.1 Creating Linear Dimensions....................................................................................................... 68 7.3.2 Deleting dimension points.......................................................................................................... 70 7.3.3 Modifying Linear Dimensions Graphically.................................................................................. 70 7.3.4 Modifying Linear Dimensions..................................................................................................... 71 7.4 Creating a Dimension (Example) ................................................................................................ 72 7.5 Intelligent Text .............................................................................................................................. 75 7.6 Positioning Dimensions using Modify Mode ............................................................................ 77 Exercise 10 – Dimensioning the drawing (Equipment Arrangement) ...................................................... 78 Exercise 11 – Dimensioning the drawing (Structural Arrangement)........................................................ 80 Exercise 12 – Dimensioning the drawing (Piping Arrangement).............................................................. 82 7.7 Angular dimensions..................................................................................................................... 84 7.7.1 Creating Angular Dimensions .................................................................................................... 84 7.7.2 Modifying angular dimensions graphically ................................................................................. 85 7.8 Radial dimensions........................................................................................................................ 85 7.8.1 Creating Radial Dimensions ...................................................................................................... 85 Exercise 13 – Creating Radial and Angular Dimensions........................................................................... 87 8 Labelling ................................................................................................................................................. 89 8.1 Labelling hierarchy ...................................................................................................................... 89 8.2 Creating / Modifying Layers ........................................................................................................ 89 8.3 Creating Labels ............................................................................................................................ 90 8.3.1 Creating General Labels ............................................................................................................ 90 8.3.2 Positioning General Labels using Modify Model........................................................................ 92 8.3.3 Creating Symbolic Labels .......................................................................................................... 93 8.4 Hide/Show Labels......................................................................................................................... 94 8.5 Label Blanking.............................................................................................................................. 94 8.6 Label Placement ........................................................................................................................... 95 8.6.1 Select ......................................................................................................................................... 95 8.6.2 Position ...................................................................................................................................... 95 8.7 Creating General Labels Example .............................................................................................. 97 8.8 Creating Symbolic Labels Example ........................................................................................... 99 Exercise 14 - Labelling ................................................................................................................................ 100 9 2D Drafting............................................................................................................................................ 103 9.1 2D Drafting Hierarchy ................................................................................................................ 103 9.2 Creating Sheet Note and View Note elements ........................................................................ 103 9.3 Creating primitives..................................................................................................................... 104 9.4 2D Primitives............................................................................................................................... 105 9.4.1 Lines......................................................................................................................................... 105 9.4.2 Shapes ..................................................................................................................................... 105 9.4.3 Symbols ................................................................................................................................... 106 9.4.4 Text .......................................................................................................................................... 106 9.5 Construct .................................................................................................................................... 106 9.5.1 Construct Group....................................................................................................................... 106 9.5.2 2D Copy ................................................................................................................................... 107
www.aveva.com 6
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002 9.5.3 Repeat...................................................................................................................................... 107 9.5.4 Fillet Arc ................................................................................................................................... 108 9.5.5 Chamfers.................................................................................................................................. 108 9.5.6 Parallel Lines ........................................................................................................................... 108 9.5.7 Tangent Line ............................................................................................................................ 108 9.5.8 Ray Line ................................................................................................................................... 109 9.5.9 Constructed Line...................................................................................................................... 109 9.5.10 Bisector Line ........................................................................................................................ 109 9.5.11 Local Symbols ..................................................................................................................... 109 9.6 Edit............................................................................................................................................... 110 9.6.1 Edit>Primitive ........................................................................................................................... 110 9.6.2 Edit>Move Primitive/Node To .................................................................................................. 110 9.6.3 Edit>Move Primitive By ............................................................................................................ 110 9.6.4 Edit>Move Node By ................................................................................................................. 110 9.6.5 Edit>Line Gap .......................................................................................................................... 110 9.6.6 Edit>Line Trim.......................................................................................................................... 110 9.6.7 Edit>Rotate .............................................................................................................................. 110 9.6.8 Edit>Demolish Symbol............................................................................................................. 110 9.6.9 Edit>Action Group.................................................................................................................... 110 9.7 Utilities (2D) ................................................................................................................................ 111 9.7.1 Load Text ................................................................................................................................. 111 9.7.2 Sketch Drafting ........................................................................................................................ 111 9.7.3 Dynamic Primitives .................................................................................................................. 112 9.8 Creating 2D Primitives Example ............................................................................................... 112 9.8.1 Creating a New Note................................................................................................................ 112 9.8.2 Added 2D Text to a View Note ................................................................................................ 112 9.9 Adding 2D Primitives to a Drawing Sheet Note ...................................................................... 114 Exercise 15 – 2D Draughting ...................................................................................................................... 116 10 Section Planes ................................................................................................................................ 118 10.1 Section Planes............................................................................................................................ 118 10.2 Creating Flat Planes................................................................................................................... 119 10.3 Modifying Flat Planes ................................................................................................................ 120 10.4 Flat Plane Example..................................................................................................................... 120 Exercise 16 – Section Planes ..................................................................................................................... 122 Appendix A............................................................................................................................................... 123 Wireline .................................................................................................................................................. 123 Modelled Wireline .................................................................................................................................. 123 Local Hidden Line .................................................................................................................................. 124 Global Hidden Line ................................................................................................................................ 124 Universal Hidden Line............................................................................................................................ 125 Appendix B............................................................................................................................................... 127 Intelligent Text........................................................................................................................................ 127 Alternative Character Set....................................................................................................................... 128
www.aveva.com 7
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
www.aveva.com 8
CHAPTER 1
1
Introduction
Draft is the AVEVA Plant Drawing Production and Annotation Module. The Drawing information is taken directly from the Design or Draft Databases and is therefore intelligent so will update automatically to reflect any Design Changes.
1.1
Aim
During the course participants will learn the basic functions required to produce, dimensioned and annotated drawings.
1.2
Objectives
1.3
To understand the DRAFT hierarchy Be able to create Drawings and Drawing Sheets. Be able to create scaled and non scaled Views using various methods. Dimension, Label and Annotate Drawings. Understand the use of Section Planes and create a Flat Section Plane
Prerequisites
Trainees should have attended “TM-1001 AVEVA Plant (12 Series) PDMS Foundations” and be familiar with Microsoft Windows
1.4
Course Structure
Training will consist of oral and visual presentations, demonstrations and set exercises. Each workstation will have a training project, populated with model objects. This will be used by the trainees to practice their methods, and complete the set exercises.
1.5
Using this guide
Certain text styles are used to indicate special situations throughout this document, here is a summary; Menu pull downs and button press actions. Are indicated by bold dark turquoise text. Information the user has to Key-in Will be red and BOLD Annotation for trainees benefit
L
Additional information
Refer to other documentation
System prompts should be bold and italic in inverted commas i.e. 'Choose function' Example files or inputs will be in the courier new font, colours and styles used as before.
www.aveva.com 9
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
www.aveva.com 10
CHAPTER 2
2
DRAFT features
DRAFT is the drawing production module of AVEVA Plant PDMS. It allows the designer to generate fully annotated engineering drawings directly from data in the PDMS Design model. Drawings can be easily updated to reflect changes in the design model. Within DRAFT there a number of applications that are used for specific functions associated with the production of drawings. These applications are
General Auto drawing production AutoDRAFT Administration
The DRAFT GUI has been designed to allow the designer to generate and retrieve industry standard engineering drawings efficiently. The designer can add dimensioning and other annotations with information taken directly from the model. The DRAFT drawing can be created with any view angle and the representation of the drawing graphics is controlled by representation rules that are pre-defined by the project administrator. Various levels of wireline and hidden line removal can be used. Sectional views can be generated by the creation of flat or stepped section planes. The scale of the drawing can be selected from a set of Metric, Architectural and Engineering values, with the option of an automatic scale selection to use the largest scale possible for the given drawing. Labels can be attached to any design element and used to display any attribute of the design element. The format, content and appearance of the labels are controlled by the designer. Direct reference to the design data, combined with a simple update operation, ensures that the annotation always reflects the current state of the design model. Autotagging is a quick solution for automatically generating labels that match a tagging rule. The rule determines the type of label and which design items the labels will be applied to. Dimensions are calculated directly from the design model, the designer can control the format, content and appearance of the dimensions. As with labeling, direct reference to the design data ensures that the annotation always reflects the current state of the design model with a simple update operation. 2D drafting allows the designer to generate additional 2D annotation on the drawing sheet. Also, like other DRAFT data, 2D annotation can be linked to design data and can be updated to follow the changes that occur in the design model. Automatic drawing production is not covered in this training course. As the title of the application infers, this application enables the designer to produce annotated drawings automatically. A set of rules determine how the annotation is generated. The drawings can be edited, if necessary, using the normal editing options in DRAFT. There are a number of ADP applications for different disciplines. AutoDRAFT is not covered in the training course. This application imports drawings directly from DRAFT into AutoCAD. However it should be noted that once this action is done, the drawing in AutoCAD has no direct link to the design model, data and future updates of this AutoCAD drawing are not possible from the model. Symbols and drawing frames can be exported from AutoCAD directly into DRAFT.
www.aveva.com 11
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Administration is not covered in this training course. Using this application, the project administrator is responsible for the customization of the DRAFT environment. This includes setting default attribute values, creating drawing frames, (commonly referred to as backing sheets), symbols and labels. The administrator will also set the representation rules, labelling rules, naming conventions, lines styles, hatch patterns and available symbology.
L
Note: The Administration Option is only available to Free Users or Members of the DRAFTADMIN Team
www.aveva.com 12
CHAPTER 3
3
Getting started
3.1
Entering a DRAFT Session
To start AVEVA PDMS, Select AVEVA > PDMS 12.0 > Run PDMS
Enter the name of the project:
Sample
Enter the Username:
USERA
Enter the Password:
A
Enter the MDB:
TRAINA
Select the module required:
DRAFT
When all the necessary details have been entered the form will look like this. Ensure that the Read Only box is unchecked.
Click OK When PDMS DRAFT has been loaded, a default screen layout will be displayed
www.aveva.com 13
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
3.2
Current Element Definition
When working in any database, PDMS is always located at a specific element in that database. This element is known as the Current Element (CE). In Draft you are able to navigate to both the Draft and the Design Database so the Current Element (CE) may be a Design Element.
3.3
Displaying the Explorer windows
To display the DRAFT and DESIGN Explorer windows select Display>Explorers from the main pull down menu.
The Design Explorer is displayed using Display > Explorers > Design
For information on the manipulation and docking of windows please refer to TM-1001 AVEVA Plant (12 Series) PDMS Foundations
3.4
Displaying Toolbars
To display toolbars, click the right mouse button while the cursor is located over the main bar menu and the following pull down will be displayed. Click the relevant toolbars for them to be displayed.
www.aveva.com 14
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Display the Working Sheet toolbar as described below if it is not displayed.
3.5
Displaying the Draft Drawing Sheet
In the Draft Explorer, select the DEPT /Project_Libraries by clicking on the + sign next to it with the lefthand mouse button. The hierarchy, shown in the Explorer, will then be expanded to show the REGIs owned by the DEPT. Continue to work down the tree by selecting the following elements:
REGI /DRA/PRJ/TMP/PIPING DRWG /DRA/PRJ/TMP/PIPING/A0 SHEE /DRA/PRJ/TMP/PIPING/A0/S1 Using the Working Sheet toolbar, display Drawing Sheet /DRA/PRJ/TMP/PIPING/A0/S1 by clicking on the button on the toolbar:
The Sheet displayed is a Draft backing Sheet containing one empty view:
www.aveva.com 15
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
The sheet can also be displayed clicking the right mouse button with the cursor positioned over the CE and selecting Open Sheet from the displayed menu.
3.6 3.6.1
Using the mouse and keyboard to manipulate the view of the sheet Mouse buttons
Left Mouse button
Clicking the left mouse button with the pointer over an element makes the element the CE. The element may be a Design element (part of the engineering item displayed) or a Draft element (for example, the outline of the drawing sheet, a label, or a dimension). If a Draft element is clicked, the Draft Explorer changes appropriately.
Similarly, if a Design element is clicked, the Design Explorer display will change:
www.aveva.com 16
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Middle Mouse button The middle button allows the user to increase and decrease the scale of the displayed view, as follows: Windowing in - using a rubber band technique, define the area to be zoomed into. Zooming in - Position the pointer at the point you want to become the centre of the view. Hold down the (shift) key and repeatedly click the middle button, as required. After each click, the display zooms in by a factor of 1.5, centred on the current pointer position. Zooming out - Position the pointer at the point you want to become the centre of view. Repeatedly click the middle button, as required. After each click, the display zooms out by a factor of 1.5, centred on the current pointer position.
L
If your mouse has a wheel, then rotating the wheel away from you will zoom in, towards you will zoom out.
Right-hand mouse button Clicking the right-hand button, when the pointer is in the main display, activates a shortcut menu. •
Refresh – refreshes the graphics
•
Reset Limits – zoom out until the full extent of the sheet is displayed
•
View Frames on/off – turns the visibility of all view frames on the current sheet on or off.
•
Add CE – adds the current sheet to the display
•
Highlight CE – highlights the CE in the display by flashing
•
Goto – displays the following sub menu, select the element to navigate to
•
Colour Settings – displays the following sub menu, selection the option to change
•
3D view – displays the 3D view
For Drawing production via the 3D View please refer to TM-1206 Drawing Production (Advanced).
3.6.2
Keyboard Commands (Zooming and Panning)
Zooming Some additional features for zooming The Pg Up key can be used for zooming in. The Pg Dn key can be used for zooming out. Holding down the Ctrl key while zooming in or zooming out using the middle mouse button, doubles the zoom factor. The numeric keypad odd-numbered keys can be used for zooming (see the diagram below).
www.aveva.com 17
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Panning Panning (moving the displayed area across the overall drawing) can be achieved by the following methods, once you have zoomed in. Use the mouse pointer to drag the Drawing display slider controls. Use the up/down, left/right arrow keyboard (see diagram below). As required, hold down the Ctrl key to increase the step size by a factor of 10. Or, as required, hold down the (shift) key to decrease the step size by a factor of 10. Use the numeric keypad even-numbered keys, as shown below: 7
8
9 In
In
Arrow keys pan in directions shown
4
5
6
1 Out
2
3 Out
Numeric Keypad keys 2, 4, 6, 8 pan in directions shown by half view width. Keys 7 and 9 zoom in Keys 1 and 3 zoom out
3.7
Resetting the Draft View
When the Draft Display has been zoomed or panned to a specific region it useful to reset the display back to the full screen display. This can be done by using the Right hand Mouse Button and selecting Reset Limits as describe above or by using the Reset Limits Icon from the side of the Drawing display window.
3.8
Grid
It is normal practice to position annotation on a grid so that elements are spaced evenly on the Drawing Sheet.
3.8.1
Displaying and Hiding the Draft Grid
To display the Display Grid, clicking on the Grid the toolbar at the side of the Drawing display window.
Icon. This is on
www.aveva.com 18
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
The grid is hidden by re-selecting the Grid Icon
3.8.2
Changing the Grid Spacing
The Grid Spacing can be changed by selecting the Grid Icon using the Right Hand Mouse Button and selecting Spacing.
The Grid Size and offset can be set as required Size X 10
Size Y 10
At X
At Y
0
0
OK
3.8.3
Positioning Elements on a Grid (Snap)
Elements of a drawing can be positioned at grid points, by clicking on the SNAP to grid button feature will be discussed later in the course.
3.9
. This
Saving and Restoring Views
Up to 4 views can be saved so that the designer can navigate quickly to a specific area of the Drawing there use is similar to how the camera icon is using in Design.
Views are saved using the Right Hand Mouse Button and Restored using the Left Hand Mouse Button
www.aveva.com 19
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
3.10 Settings User Defaults On entry into DRAFT the default libraries are set. These are predefined by the Administrator. These Library Setting store the location of Symbols, Backing Sheets, Drawing Styles etc. that Draft uses during Drawing Production. The system settings defaults can be modified for the current session. The user can modify the required libraries for the current session, by selecting Settings>User Defaults. The User Defaults form is displayed
www.aveva.com 20
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Exercise 1 - Viewing Controls Using the above examples display the Design Explorer, and Sheet /DRA/PRJ/TMP/PIPING/A0/S1 Now you can familiarise yourself with some of Draft’s viewing controls experiment by using the mouse and keyboard, as described above zoom, pan and widow around the Drawing Sheet. Change the Grid size to 10mm and display the Grid.
L
Do not close the Main Display window, because you will use it in the next parts of the exercise.
www.aveva.com 21
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
www.aveva.com 22
CHAPTER 4
4 4.1
The PDMS DRAFT database hierarchy DRAFT database hierarchy
WORLD
DEPT
DEPT
REGI
REGI
DRWG
DRWG
SHEE
SHEE
As with all database elements, the owning elements can contain any number of legal members, as shown in the above hierarchy chart. The DEPT, REGI and DRWG elements can be viewed in the DRAFT explorer, but cannot be displayed graphically. The principal element is the Drawing (DRWG) element. All elements below the DRWG in the hierarchy are used to store the information required to completely define the drawing. A drawing can contain one or more Sheet (SHEE) elements. A Sheet is the highest level element that can be displayed in the graphical view. A drawing can own one or more Sheet (SHEE) elements. A sheet can own one or more VIEW elements. These views are projections of parts of the design database. A view element has attributes that; • • •
Define the viewing parameters (view direction, through point and scale). Define the size, position and orientation of the region on the sheet. Refer to a drawlist that contains a list of the DESIGN elements that are to be displayed in the VIEW picture.
www.aveva.com 23
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
4.2
Creating the DRAFT hierarchy
4.2.1
Creating a DEPT (Department)
Navigate to the World /* using the Draft Explorer.
To create the DRAFT hierarchy select Create>Department from the main bar menu, the Create DEPT form is displayed.
Name /TRAINING_DEPT
Select OK
The Department Information form will then be displayed, and the name of the department will be displayed within the form. If a Registry is to be created, the Create Registry box should be checked.
Clicking on the Attributes button will display the Department Attributes form, the values selected will be the default values used for the creation of all elements in this DEPT.
L
The Department Attributes form is discussed in full later in the chapter.
Click OK, and the Create REGI form will be displayed, only if the box was checked. Clicking on Cancel will cancel the operation of creating a DEPT. Select OK
www.aveva.com 24
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
4.2.2
Creating a REGI (Registry)
If the Create Registry box was checked in the Create DEPT form , the Create REGI form will be displayed, otherwise select Create>Registry from the main bar menu. Name /TRAINING_REGI
Select OK and the Registry Information is displayed. Clicking on Cancel will cancel the operation of creating a REGI
If a drawing is to be created immediately, check the Create DRAWING box. The selection of Explicitly or From Template only applies if the Create DRAWING box is checked.
L
Note: The different methods of creating drawings explicitly or from templates will be explained later in this manual.
Clicking on the Attributes button will display the Registry Attributes form, the values selected will be the default values used for the creation of all elements in this REGI.
4.3
DEPT and REGI attributes
The attributes form is similar for both DEPT and REGI elements with one exception that will be noted. The name of the current DEPT or REGI will be displayed in the name field of the form.
4.3.1
Size and Units
The Width and Height values will define the default drawing size that will be used upon creation of a drawing.
www.aveva.com 25
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
The Backing sheet selection by default is unset, toggling the Radio button will set the default backing sheet reference to be used on drawing creation. • • •
Unset – will leave the backing sheet reference unset Reference – clicking on the pull down will display the backing sheets available, and from this a default sheet can be set. Filename – a reference to a PDMS plotfile
In the above example the default Backing Sheet for the Department has been set to a standard A0 size. The Units attributes sets the default distance and bore units Click on the Distance pull down and the following options are displayed • • • • • • • •
Feet and Inches USA Feet and Inches Inches Inches USA Inches PDMS Millimetres Centimetres Metres
output of the form 5’-5 13/16” output of the form 5’5.13/16 output of the form 0.5 or 1.5 or 24.0 output of the form ½” or 1 1/2” or 24 output of the form 0.1/2 or 1.1/2 or 24 distance in mm. distance in cm. distance in m.
Click on the Bore pull down and the following options are displayed • • • • • •
Inches Inches USA Inches PDMS Millimetres Centimetres Metres
output of the form 0.5 or 1.5 or 24.0 output of the form ½” or 1 1/2” or 24 output of the form 0.1/2 or 1.1/2 or 24 distance in mm. distance in cm. distance in m.
The precision attributes set the default values to the number of decimal points or fractions of an inch. Final Designer is not covered as part of the Basic Drawing Production training.
www.aveva.com 26
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
4.3.2
Intelligent Text
The positional code words and output format for Plant drawings will always be toggled to ENU (East North and Up).
L
XYZ Co-ordinates are normally associated with AVEVA Marine
4.3.3
Pens (and Fonts)
The default pen colours and line styles for the noted objects in the form can be modified.
The form is self explanatory with the exception of Fonts. Prior to AVEVA PLANT (12 Series) Draft was limited to 4 built in fonts as specified by the Draft Administrator, from AVEVA PLANT (12 Series) Standard Windows True Type Fonts have been introduced.
www.aveva.com 27
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
By Default Fonts are set to Standard Thin Upright which is a standard PDMS Font. Select a True Type font The True Type Fonts Available in Draft are specified by the AVEVA Plant (PDMS) Administrator for the project.
On this project only two True Type Fonts are Available.
Select Cancel
Select a PDMS font
The Standard Thin Upright Font is selected.
Other Options are available via the Pull down Menu
On the Draft Basic Course the Fonts should be left set to Standard Thin Upright.
L
Draft and True Type Fonts can not be mixed on the same sheet, this includes any Symbols and Backing sheets that may be used.
L
Example Symbols, Labels and Backing Sheets are included in Draft Sample Project and are prefixed /TT then can be found in /TT/Master_Libraries and /TT/Project_Libraries.
The use of True Type Fonts is covered in TM-1206 AVEVA Plant (12 Series) Drawing Production (Advanced)
www.aveva.com 28
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
4.3.4
Miscellaneous
The Null text can consist of up to 12 characters. This value is used when it is not possible to extract data from an attribute and the intelligent text system returns an error. Click on the Date Format pull down, only available in the Department attributes form and the following options are displayed • DDMMYYYY • DDMMYY • MMDDYYYY • MMDDYY Click on the Dimension Terminator pull down and the following options are displayed • • • •
Off Arrows Dots Obliques
- no terminators shown on dimension lines - arrows shown on dimension lines - dots shown on dimension lines - obliques shown on dimension lines
Click on the Leader Terminator pull down and the following options are displayed • • • •
Off Arrows Dots Obliques
- no terminators shown on leader lines - arrows shown on leader lines - dots shown on leader lines - obliques shown on leader lines
Click on the Ruleset Reference pull down, and the available rulesets are displayed Click on the Hatching Ruleset Ref pull down and the available hatching rules are displayed Clicking on RESET on the form will reset all the attributes values back to the default settings
www.aveva.com 29
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Exercise 2 - Create the DRAFT hierarchy Create the DRAFT hierarchy as described above, set the default size of the drawing to A0, Add the Standard A0 Backing Sheets, set leader line and dimension terminators to Arrows. Set the name of the new DEPT to TRAINING_DEPT and the name of the new REGI to TRAINING_REGI Uncheck the Create Drawing option on the Registry Information form, as we will cover the drawing creation in the next chapter.
L
Ensure that the fonts are set to a standard PDMS Fonts as the Backing Sheets and Symbols used later in the course will be using standard PDMS font settings.
www.aveva.com 30
CHAPTER 5
5
Creating Drawings and sheets
5.1
Creating Drawings and Sheets
There are two methods of creating Drawings, Explicitly or From Template. Both methods are available, regardless of whether the drawing is created by checking the Create Drawing button on the Registry Information form, or by selecting Create > Drawing at the Draft General bar menu and selecting Explicitly, Template or Default Template
5.1.1
Creating Drawings from a Template
If a drawing is created from a template, several other elements will be created automatically. The Drawing will own a Sheet, which will own at least one View. The View will own several Layers, which are discussed later. There may be other elements, such as Sheet Notes, which are used to store text and primitives for the 2D Drafting. The Drawing will also own a Library. Draft makes extensive use of libraries, which are set up by the System Administrator. Users can only extract information from libraries; not change them. Libraries are used to store things like symbols and Drawlists (which you will use later to define the contents of a View). Libraries are accessed by the Application automatically and, therefore, you will not need to access them directly. Navigate to the Registry /TRAINING_REGI created earlier. Select Create > Drawing > From Template from the Main Menu.
www.aveva.com 31
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
The Drawing and Sheet Templates form enables you to select the source of the template and the drawing size.
L
Note: At the top of the form, the Create Mode is set to Drawing from Template. If the form is used for creating a Sheet, the Create Mode is set to Sheet from Template, but otherwise the form is unchanged.
The From pull down list displays the available discipline registry that contain the drawing templates, as set up by the System Administrator. Select Equipment Registry
Select A0 Equipment Drawing
If the Use Default Naming is checked, then the default naming convention will be used, which is DR1, DR2 etc. If this option is not checked then a name form will be displayed after clicking on the OK button.
Unset Use Default Naming and Select OK.
www.aveva.com 32
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Name DRWG_1
Select OK A particular template can be set as the default by placing a check in the Use as Default box.
The drawing is displayed in the 2D graphical window automatically upon creation, and all administrative elements will have been created.
5.1.2
Creating Drawings from a Default Template
If the standard default template is to be used, select Create > Drawing > From Default Template from the main bar menu, or click on the icon in the Create From Default Template bar menu. If the Use Default Naming is checked on the default template, then the name form will be displayed, otherwise the default naming convention will be used.
Select Use Default Naming
Select Create New From Default Template
The New Drawing will be created using the Default Naming Convention.
www.aveva.com 33
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
5.1.3
Creating Drawings explicitly
If a drawing is to be created explicitly, the create options on the main bar menu will be used to create the drawing and all of the member elements, such as sheets and views. To create a drawing explicitly select Create>Drawing>Explicitly from the main bar menu and the Create DRWG form will be displayed Name /DRWG_2 Select OK The Drawing Definition form is displayed Title
Training Drawing
Date
12 June 2020
Drawn By
A. Piper
Select OK
L
The Drawing will not be displayed in the Graphics window as it is the Drawing Sheet that has the Draft geometry Drawing are only hierarchy elements like Dept or Regi.
L
Selecting Attributes can be used to change the Drawing Attributes and is similar to the Dept and Regi Attribute Form as described previously.
www.aveva.com 34
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
5.1.4
Creating Drawing Sheets explicitly
Select Create>Sheet>Explicitly from the main bar menu. A name should may be entered in this form, in this case the default name is OK. Select OK and the Sheet Definition form will be displayed
The Sheet Title, size and backing sheet should be specified,
In this case the size and backing sheet have been cascaded down from the owning Drawing / Regi
Title Training Sheet
Select Apply The intelligent text will be left as plant co-ordinates E NU
Select Dismiss
www.aveva.com 35
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Exercise 3 - Create a drawing from a template Create a drawing from a template, using an A0 Equipment Drawing. The drawing name will be DRWG_1 When created note the LIBY elements owned by the DRWG element
L
Do not delete, rename or modify these, or any of the owning members, these are controlled by the application
You will notice that the SHEE element also contains a VIEW element, which contains LAYE elements. Create another drawing, from a template, using an A0 Piping Drawing. The drawing name will be DRWG_3.
Exercise 4 - Create a drawing explicitly Create a drawing and sheet elements explicitly. The drawing name will be DRWG_2, the title will be Equipment Arrangement and the size will be A0. Set the backing sheet reference to /DRA/MAS/BACKS/MET/A0 When created note the LIBY elements owned by the DRWG element
L
Do not delete, rename or modify these, or any of the owning members, these are controlled by the application.
Create another drawing and sheet explicitly. The drawing name will be DRWG_4, the title will be Structural Arrangement and the size will be A0. Set the Backing sheet reference to /DRA/MAS/BACKS/MET/A0
www.aveva.com 36
CHAPTER 6
6
Creation and modification of Views
This chapter covers the creation and modification of views. Views created by Drawing and Sheet templates will require to be modified, whilst Drawing and Drawing Sheets created explicitly will need to have views created.
6.1
User defined view
User-Defined Views are used to draw individual items or groups of items in the design model, when the volume or limits of the items are not known. The size of the frame is independent of its contents. The scale can be automatically set to fit the design elements into the available view frame area.
6.2
Creation of user defined VIEW
A view is owned by a SHEE element, so before creation of a view ensure that the correct SHEE element is selected. Navigate to /DRWG_2/S1 From the main bar menu select Create>View>User Defined, the Create VIEW form is displayed. The name is derived from the owning element and can be accepted.
6.2.1
Select OK
User Defined View (Frame menu)
The Frame form menu enables you to switch the view frame on or off, to control the size of the frame, its position on the Sheet and its alignment relative to any other view that may be on the Sheet. The menu has the following options: •
On/Off – toggles the display of the view frame
•
Size
•
Copy size
•
Position
•
Align
www.aveva.com 37
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
6.2.1.1 Frame>Size This option has a sub-menu that allows you to set the size of the view frame in different ways: •
Cursor – displays the Point Construction Option Form. This enables the opposing corners of the view frame to be selected graphically.
The View Frame should be resized to be a big as possible within the allowable Backing Sheet Frame. Select Frame > Size
Select 2D Cursor Hit
Using the Cursor Resize the View Window using a diagonal window. •
Explicit – displays the Explicit Frame Size Form. This resizes the frame by defining its size in terms of sheet co-ordinates or proportions.
www.aveva.com 38
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
6.2.1.2 Frame>Copy Size This option has a sub-menu that allows you to copy the Width, Height or Width and Height of another view on the Sheet: • • •
Width - will prompt the user to identify (with the cursor) a view whose width is too copied. The width of the current view will then change to be the same as that of the identified view. Height - will prompt the user to identify (with the cursor) a view whose height is to be copied. The height of the current view will then change to be the same as that of the identified view. Width & Height - will prompt the user to identify (with the cursor) a view whose width and height are to be copied. The width and height of the current view will then change to be the same as that of the identified view.
6.2.1.3 Frame>Position This option has a sub-menu that allows you to position the frame in different ways: •
Cursor - enables the user to use the cursor to move the view frame by nominating a point in the view, using the option from the sub menu. The nominated point will move to the cursor position when the left hand mouse button is clicked
•
Explicit – displays the Explicit Frame Position form. This enables the user to position the view frame by defining it Sheet position in terms of sheet co-ordinates or proportions
6.2.1.4 Frame>Align This option has a sub-menu that allows you to align a specified axis or edge of the current view with the same axis or edge of another selected view on the Sheet. • • • • • •
Centre Vert - will prompt the user to identify (with the cursor) a view whose centre you wish the current view’s centre to align with vertically. The position of the current view will then change to align the view centres vertically. Centre Horiz - will prompt the user to identify (with the cursor) a view whose centre you wish the current view’s centre to align with horizontally. The position of the current view will then change to align the view centres horizontally. Top - will prompt the user to identify (with the cursor) a view whose top edge you wish the current view’s top edge to align with. The position of the current view will then change to align the views top edges. Bottom - will prompt the user to identify (with the cursor) a view whose bottom edge you wish the current view’s bottom edge to align with. The position of the current view will then change to align the views bottom edges. Left - will prompt the user to identify (with the cursor) a view whose left edge you wish the current view’s left edge to align with. The position of the current view will then change to align the views left edges. Right - will prompt the user to identify (with the cursor) a view whose right edge you wish the current view’s right edge to align with. The position of the current view will then change to align the views right edges.
www.aveva.com 39
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
6.2.2
User Defined View (View menu)
The View form menu enables the user to toggle the display of the view on or off, set the Design co-ordinates corresponding to the centre of interest of the view and offset the Design element graphics with respect to the centre of the view. The menu has the following options: • On/Off – toggles the display of the view. • Centre • Offset
6.2.2.1 View>Centre This option has a sub-menu which allows the designer to select the centre of interest of the view in different ways: • Identify - will prompt the user to identify a design element to be the centre of interest of the view. •
Cursor - displays the Point Construction Form and prompts the user to select a point with the cursor to become the centre of interest.
•
By Cursor – displays the Point Construction Form and prompts the user to select a base point and displacement with the cursor to move the centre of interest of the view.
•
Explicit – displays the User Defined Centre Position form which enables the user to enter coordinates for the centre of the view
6.2.2.2 View>Offset Displays the Design Graphics Offset Form.
This form enables the user to position the centre of the view contents, relative to the view centre.
www.aveva.com 40
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
6.2.3
User Defined View (Graphics menu)
The Graphics form menu enables the user to create and modify Drawlists as well as setting the Drawlist Reference for the view. A Drawlist holds a list of Design elements that determine what will be displayed in the view. Drawlists are independent of the views, therefore, a sheet may contain several views that refer to the same Drawlist or several views that refer to different Drawlists. Drawlists (IDLI elements) are stored in Drawlist Libraries (DLLB elements). When a Drawing is created, a library containing a default Drawlist Library is automatically created and may be used as the Drawlist for any views created on Sheets owned by that Drawing. Specific Drawlists for specific views may also be created and stored in the default Drawlist Library or in another Drawlist Library located elsewhere in the project, depending on the set-up by the Draft Administrator. The menu has the following options: • •
Drawlist Drawlist Ref
6.2.3.1 Graphics>Drawlist Displays the Drawlist Management Form
The Drawlist Library pull down list gives a list of the available Drawlist Libraries.
The Drawlists window is a scrollable list of all the Drawlists available within the selected Drawlist Library. In the example above only the default drawlist, created automatically during Drawing creation is shown The Reference List Members window displays the Design Members of the current MDB, if selected from the scrollable list.
www.aveva.com 41
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
If Drawlists is selected from the scrollable list, the available Drawlists will be displayed.
If Lists have been previously defined, they will be available for selection. If there are no Lists defined, or a list is required, clicking the Lists button will display the List/Collection form. Having defined a new List, clicking the Update button will display all defined Lists in the scrollable list for selection. For information on Lists please refer to Plant (12 Series) PDMS Foundations
TM-1001 AVEVA
The Drawlist Members window displays the Design elements or Drawlists that have been selected to be members of the current Drawlist. In the example above, no members have been selected yet. Items are added to the Drawlist by selecting them from the Reference Members List, or a List / Collection name from the scrollable list, and clicking the Add button. This creates an Add Element (ADDE) element in the Drawlist Members window. Specific items may also be removed from the Drawlist by selecting them in the Reference Members List, or a List/Collection name from the scrollable list, and clicking the Remove button. This creates a Remove Element (REME) element in the Drawlist Members window. For example, all equipment except /1301 may be required to be displayed in the view. Rather than adding each piece of equipment separately, the zone /EQUIPMENT may be added and the specific piece of equipment /1301 subsequently removed from the Drawlist.
The Navigation form menu offers an alternative method of navigation. The options are similar as those available from the Navigation pull down menu of the Members list. Note: If the Members list is displayed, it will be removed while the Draw List Management form is displayed. The buttons to the right of the Drawlists window, control the creation and deletion of Drawlists: •
Create – creates a new empty drawlist
•
Create Copy – creates a copy of the drawlist selected from the available drawlist libraries
•
Delete – deletes the currently selected drawlist
•
Clean Up – removes any drawlist members with Null or Bad references
The Delete Entry and Delete All buttons, delete the current highlighted entry from the Drawlist or all Drawlist members respectively. The Volume Defined and Limits buttons, enable the addition of all elements that are positioned wholly within a defined volume. Clicking the
www.aveva.com 42
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Limits button will display the Drawlist Limits form.
The limits are set by entering appropriate co-ordinates for opposing corners of the limits volume. After setting the limits clicking the Volume Defined button adds all elements wholly within the entered coordinates. If required, the Remove or Delete Entry buttons may be used to amend the Drawlist.
6.2.3.2 Adding Design Elements to the Drawlist (Example) Display the Drawlist Graphics > Drawlist Navigate to the EQUIPMENT Zone in the STABILIZER Site
Select the Add Button
The Equipment zone will be added to Drawlist Members
Repeat the process for
EQUIP-STRU and
PIPEWAY
6.2.3.3 Graphics>Drawlist Ref Displays the Drawlist Management Form
This form enables you to reference the current view to a Drawlist so that the Drawlist Members are displayed in the view. It should be noted that a view may only reference one Drawlist. The Options scrollable list allows the owning Sheet’s or the owning Drawing’s Drawlist to be used. The VIEW’s current Drawlist may be used, or the Drawlist reference may be unset. The Drawlist Library scrollable list allows you to choose from a list of Drawlist Libraries, as set up by your Draft Administrator. The ‘Drawing’ selection, as shown above,
www.aveva.com 43
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
refers to the Drawlist Library created automatically when the views owning Drawing was created. The Drawlist Contents window displays the contents of the selected Drawlist when the Display button is clicked. This allows you to check the contents of the Drawlist you have selected. The Modify button displays the Drawlist Management form enabling you to modify or create a new Drawlist as described previously.
6.2.4
User Defined View (General)
6.2.4.1 Title In Draft we always draw intelligently so it is normal practice to display the view title from the database to avoid free text.
6.2.4.2 View Type A view type must be selected. The pull down menu displays the following (refer to appendix A) • • • • •
Universal Hidden Line – causes intersection lines between significant elements to be generated Global Hidden Line – gives a picture where all hidden lines are removed Local Hidden Line – gives a picture where all hidden lines are removed from equipment elements. Where two or more equipment elements overlap, the overlapping elements are shown in wireline Modelled Wireline – blends the intersection of primitives Wireline – Shows all elements and points
6.2.4.3 Section Mode: A section mode must be selected. The pull down menu displays the following • •
Standard – this option sections all Design elements where appropriate Omit Fractional Pipe Components – this option removes any partial pipe components from the display, where the P0 is outside the front and back sectioning planes. All lengths of implied tube that are outside the front and back sectioning planes will be removed from the drawlist.
www.aveva.com 44
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
6.2.4.4 Style The scrollable list shows the available Representation Rulesets (RRST) elements that are used to control the display representation of the different types of Design elements within the view. Representation Rulesets are created by the Draft Administrator.
6.2.4.5 Hatching Rules The scrollable list displays the available Hatching Rulessets that are used to control the hatching of different types of Design elements that may be cut when a section is applied. Hatching Rulesets are created by the Draft Administrator.
6.2.4.6 Change Rules The scrollable list shows the available Change Rulesets that are used to control the appearance of changed Design elements and annotation on subsequent updates of the drawing. For the use of Change Rulesets please refer to TM-1206 Drawing Production (Advanced).
6.2.4.7 Direction The required view direction may be selected from the pull-down list of pre-defined directions. Alternatively, a view direction, e.g. N 45 E, may be typed into the text box. The Derived button will prompt you to identify a design element in the Graphics area for setting the view direction.
6.2.4.8 User Define View General Tab (Example) Title
PLAN
View Type
Universal Hidden Line
Section Mode
Standard
Style
/DRA/PRJ/REPR/GEN/BASIC
Hatch Rules
unset
Change Rules unset
Direction
Down
www.aveva.com 45
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
6.2.5
L
User Defined View (Scale)
For Draft to calculate a scale, the drawlist must contain elements. •
Auto Scale – this sets the view scale such that all of the design elements in the Drawlist will fit just within the view frame. The actual scale will be displayed in the Scale text box. The Auto Scale operation also sets the through point to the Site coordinates corresponding to the centre of interest of the view.
•
Nearest – it is unlikely that Auto Scale will produce a standard scale for the view. Clicking the Nearest button will select the nearest available standard scale, based on the metric, architectural or engineering scale option selected, and set the view scale. The standard scales can also be selected from the scrollable list next to the Nearest button.
6.2.5.1 User Defined View (Scale) (Example) Select Auto Scale button followed by the Nearest Button, this should give a scale of 1/50.
www.aveva.com 46
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
6.2.6
User Defined View (Intelligent text)
Please refer to this option earlier in the text as is the same as at DEPT and REGI elements.
6.2.7
User Defined View (Attributes)
Clicking on the Attributes button on the User Defined View Form displays the User Defined View Attributes Form.
The following attributes of the view can be modified from this form •
Graphics Angle – controls the angle of the design graphics within the view. A positive angle gives an anti-clockwise rotation. The view direction remains the same.
•
View orientation - controls the orientation of the view and its contents. The selectable directions correspond to the direction of the ‘top’ of the view region relative to the top of the screen, e.g. selection of Right will cause the view and its contents to be rotated through 270 degrees.
•
Arc Tolerance - controls the difference between the ‘true’ and the ‘facetted’ representation of curves of the graphical output for the view, being set in units of hundredths of a millimetre on the drawing. (default value 15.) The actual value used by DRAFT depends on the scale of the VIEW. The lowest value that it may be changed to is 1. Although lower values will give a better representation, the time required to display the graphics is increased.
•
Perspective - a value of 0 gives a parallel view. The value is related to the view angle.
•
Gapping Controls - the gap (in mm) inserted in view lines crossed by other lines such as centrelines, Plines, etc.
•
Note Line Pen – this option controls the appearance of the view frame (assuming it is visible). The value set will also be cascaded down to any Layers subsequently created as members of the view. The Note line Pen may be one of the standard pens or a user-defined pen set-up by the Draft Administrator.
The colour assigned to the Note Line pen can be selected from the pull down menu.
www.aveva.com 47
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Or by clicking on the Pick button a colour palette is displayed and the colour can be selected
•
6.2.8
The linestyle and thickness can be selected from the appropriate pull down menus.
User Defined View (Change Highlighting)
For information on Change Rulesets and Change Highlighting please refer to TM-1206 Drawing Production (Advanced).
6.2.9
User Defined View (Update Design on Apply)
Whenever any settings on the User-Defined View form are modified, the user must select Update Design and click Apply (or select Graphics>Update>Design from the main menu bar).
Selecting Use Background Process will start a background process for updating design.
www.aveva.com 48
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
For Drawing production using a Background Process please refer to TM-1206 Drawing Production (Advanced).
6.2.10 Creating local rules Local Rules may be set up as VIEW members in the same way as Library rules. The resulting graphical representation is determined as follows: •
Local Rules always have priority over Rules within Rulesets in Libraries.
A Rule’s priority is determined by its position in the list, the higher in list the higher its priority, but a Local Rule will still have a higher priority than the top Ruleset Rule. This means that the more specific rules should always be placed earlier in the list. To create Local Rules select Create>View>Local Rules and the Local Rules form is displayed.
Click on Create and the Create RRUL form is displayed. Enter a name and click OK.
Select the elements for which the rule is to be applied, either by specifying the type from the pull down menu or toggling the name option and entering the name or names of elements. Set the criteria and select the style required from the available style libraries. These libraries will have been set up by the DRAFT administrator. Click Apply and a local rule will be created and will apply to the current view element only. For More information on Local Rules please refer to TM-1206 Drawing Production (Advanced).
www.aveva.com 49
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Exercise 5 – Creating a User Defined View (Equipment arrangement) Navigate to the sheet DRWG_1/S1, which is the template created sheet and display the sheet. Navigate to the view /DRWG_1/S1/V1
L
Note: that the view has already been created
The view should be modified using the Modify>View>User Defined option. Add the zone /EQUIPMENT and the STRU elements /EQUIP-STRU and /PIPEWAY to the Drawlist. Set the view frame size as big as possible, the view direction to Down and the scale to suit. Use the style /DRA/PRJ/REPRE/GEN/BASIC and the view type Universal Hidden Line The resulting drawing should look similar to the picture below
www.aveva.com 50
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Experiment with changing the frame size and recalculating the scale of the drawing.
www.aveva.com 51
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Exercise 6 – Creating a User Defined View (Piping arrangement) Navigate to the sheet DRWG_3/S1, which is the template created sheet and display the sheet. Navigate to the view /DRWG_3/S1/V1
L
Note: that the view has already been created
The user will have to use the Modify>View>User Defined option. Add the zone /EQUIPMENT, the zone /PIPES, the zone /RACKPIPES, the zone /EQUIPRACK-ACCESS, the zone /STABCOLUMN-ACCESS and the stru elements /EQUIP-RACK and /PIPEWAY to the Drawlist. Set the view frame size as big as possible, the view direction to Down and the scale to suit. Use the style /DRA/PRJ/REPRE/GEN/BASIC and the view type Universal Hidden Line The resulting drawing should look similar to the picture below
www.aveva.com 52
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
www.aveva.com 53
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
6.3
Limits defined view
Limits-Defined Views are used to draw the contents of a specified volume of the model. The Limits, are defined in project co-ordinates, and are represented by the size of the View frame at the selected scale. The View frame can include matchlines with text showing the co-ordinates of the View limits.
6.4
Creation of limits defined VIEW
A view is owned by a SHEE element, so before creation of a view ensure that the correct SHEE element is selected. From the main bar menu select Create>View>Limits Defined, the Create VIEW form is displayed. The name is derived from the owning element and can be accepted. Select OK The Limits Defined View form will then be displayed. The Limits-Defined View form is similar to the UserDefined View form, but has an additional Limits tab for setting the limits of the view. It also has a Matchlines check box, which switches matchlines on and off. Also, the Scale options are slightly different.
6.4.1
Limits Defined View (General Menu)
Title
PLAN
View Type
Universal Hidden Line
Section Mode
Standard
Style
/DRA/PRJ/REPR/GEN/BASIC
Hatching Rules unset Change Rules unset Direction
Down
www.aveva.com 54
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
6.4.2
Limits Defined View (Limits Menu)
The Limits pull down menu displays the following sub menus • • • • • • • • •
From Element From Design Point From Pline Any End From Pline Prop’n From 3D Cursor From To Copy From View Drawlist Members
The limits can be set using the sub menus from under the above options, by using the cursor and identifying the pick points as selected. The limits can also be copied from another view using the Copy From View option, or calculated by the application using the Drawlist Members option.
6.4.3
Limits Defined View (Limits)
The limits can be set explicitly using project coordinates, which will define the area of the model to be displayed in the view. Checking the box next to the coordinate value, will create a section plane at that position. Refer to section Chapter 10 for section planes
In this example the limits will be initially calculated based on the Drawlist Items. Select Graphics > Drawlist and add EQUIPMENT, EQUIP_STRU and PIPEWAY.
www.aveva.com 55
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Select Limits > Drawlist Members .
The Limits will be set based on the view content and could now be changed as appropriate
6.4.4
Limits Defined View (Scale)
The scale of the view can be automatically calculated by clicking the following •
Set Scale – this calculates the scale of the view based on the View Frame Limits and the Limits of the view. The value in the % gadget is used when using this option. The scale displayed is actual scale value calculated * %.
•
Nearest – it is unlikely that Set Scale will produce a standard scale for the view. Clicking the Nearest button will select the nearest available standard scale, based on the metric, architectural or engineering scale option selected, and set the view scale. The standard scales can also be selected from the scrollable list next to the Nearest button.
www.aveva.com 56
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Set the percentage to 50% and select Set Scale and Nearest, note the size of the View.
Change the percentage to 80% and select Set Scale and Nearest again note the size of the View.
Draft calculates the size of the view bases on the available drawing region and the scale.
www.aveva.com 57
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
6.4.5
Limits Defined View (Matchlines)
If the Matchlines box is checked and the Update Graphical Aids button is clicked, matchlines will be displayed around the limits of the view with the respective co-ordinates
6.4.6
User Defined View (Update Design on Apply)
Whenever any settings on the Limits-Defined View form are modified, the user must select Update Design and click Apply (or select Graphics>Update>Design from the main menu bar).
Selecting Use Background Process will start a background process for updating design. For Drawing production using a Background Process please refer to TM-1206 Drawing Production (Advanced).
www.aveva.com 58
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Exercise 7 – Creating a Limits Defined View (Equipment Arrangement) Navigate to the sheet DRWG_2/S1, which is the explicitly created sheet, and create 2 views using the Create>View>Limits Defined option. Add the zone /EQUIPMENT and the STRU elements /EQUIP-RACK and /PIPEWAY to the drawlist, set the view frame size. Set the limits using Limits>Drawlist Members , the scale and the view direction. The view directions will be D and E respectively for the views. Make the views as big a possible. Use the style /DRA/PRJ/REPRE/GEN/BASIC and the view type Universal Hidden Line
www.aveva.com 59
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
www.aveva.com 60
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Exercise 8 - Creating a Limits Defined View (Structural Arrangement) Navigate to the sheet DRWG_4/S1, create 3 views using the Create>View>Limits Defined option. Add the STRU element /EQUIP-RACK and Set the view frame size. Set the limits using Limits>Drawlist Members , the scale and the view direction. The view directions will be D. Use the style /DRA/PRJ/REPRE/GEN/STRU and the view type Universal Hidden Line Modify the elevation of the view limits to the elevations shown • • •
L
View 1 – Elevation from U 101000 to U 100000 View 2 – Elevation from U 107000 to U 104000 View 3 – Elevation from U 108000 to U 107000
Remember you can copy and align views.
The Section Plane Button also will need setting on the limits form.
www.aveva.com 61
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
www.aveva.com 62
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
6.5 6.5.1
Creating views with predefined frames Predefined frames
Selecting Create>View>Predefined Frame displays the following form. This allows the user to create a number of views for the current sheet, based on the configuration selected from the View Configuration form. The view directions for the views can be selected from the pull down menus adjacent to the selected view option on the form.
The view spacing value is the distance between the limits of the views.
The following shows a typical sheet layout for the predefined views
www.aveva.com 63
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Exercise 9 – Creating Predefined Views Create a drawing explicitly, set the backing sheet to /DRA/MAS/BACKS/MET/A2. The drawing name will be DRWG_5 and the size will be A2. Create 4 views with predefined frames, using the option Create>View>Predefined Frame with the view direction set to Down for all the views. Using the option Modify>View>Limits Defined, add equipment /C1101 to the drawlist, set the limits using Limits>Drawlist Members, and the scale. Then modify the elevation of the view limits to the elevations shown. • • • •
View 1 – Elevation from U 101300 to U 106975 View 2 – Elevation from U 106975 to U 112650 View 3 – Elevation from U 112650 to U 118325 View 4 – Elevation from U 118325 to U 124000
Ensure that the box next to the elevations is checked
Use the style /DRA/PRJ/REPRE/GEN/EQUIP and the view type Universal Hidden Line.
www.aveva.com 64
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
www.aveva.com 65
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
www.aveva.com 66
CHAPTER 7
7
Dimensioning
Dimensions are calculated directly from the design model. You can control the format, content and appearance of the dimensions. The administrator can define suitable project defaults. Direct reference to the design data means that the annotation always reflects the current state of the design model, with a simple update annotation operation. Once the dimensions have been created, the position and orientation of dimensions can be adjusted graphically.
7.1
Dimension Hierarchy
Dimensioning elements are created under Layers owned by Views, as shown in the following diagram. Different types of dimension are created on different layers. All these elements will be created automatically as the view is dimensioned. SHEE
VIEW
VIEW
LAYE
LDIM
DPPT
7.2
ADIM
RDIM
PDIM
DPPT
Dimension Types
There are four generic dimension types available in DRAFT, namely, Linear, Angular, Radial and Pitch Circle Diameter. These allow intelligent dimensions to be created to dimensioning standards.
100
LINEAR DIMENSION
ANGULAR DIMENSION
RADIAL DIMENSION
J200
PITCH CIRCLE DIAMETER
www.aveva.com 67
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
7.3
Linear Dimensions
Linear dimension elements are created under Layers owned by Views, as shown in section 7.1. Linear dimensions can contain the following dimension points, DPOI, DPPT or DPBA elements. The dimension element and the dimensions are automatically created by the application. Overshoot
Dimension Line
Projection Line Direction
Terminator
Dimension Direction Projection Line
}
Offset
}
Clearance
Dimension Points
The diagram illustrates the following features that comprise a linear dimension • • • • • • •
L
Dimension Point - A LDIM (linear dimension) must contain at least 2 dimension points (DPPT). Projection Line – a projection line will be drawn from each dimension point in a direction specified by the user. A projection line can have intelligent text. Dimension Line – a dimension line will be drawn between all projection lines, these have terminators. Dimension Direction – this direction is defined by the user. Offset – the distance of the dimension line from the dimension point. Clearance – distance of start of projection line from dimension point. Overshoot – distance of end of projection line from dimension line.
Note: The values shown in the dimension text are taken directly from the 3D Design model. If the elements associated with the dimension points are moved in DESIGN, the dimension can be updated automatically by selecting Graphics>Update>Annotation.
7.3.1
Creating Linear Dimensions
Linear Dimensions can be created by selecting Create>Dimension>Dimension Linear or by clicking on the required style from the Linear Dimension Toolbar. If the SHEE has multiple views ensure that the correct LAYE is selected from the Layers toolbar pull-down.
The dimensions that are members of the displayed LAYE can also have their display turned off.
www.aveva.com 68
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Creating Linear dimensions using Create>Dimension>Dimension Linear will display the following form.
The name of the View and the View Direction are shown at the top of the form. The following can be set via this form •
Type– gives the following options.
Chained
Tail
Truncate
• •
Direction – the dimension line direction is the direction with respect to the world. Terminators – can be one of the following
• •
Arrows Dots Obliques Off
Projection Line Text – can be selected from the pull down Projection Line Text Angle – allows the text to be orientated from the projection line
www.aveva.com 69
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Click on the Derived button and the user will be prompted to identify a design element to derive the direction of the dimension.
Click OK and the following form will be displayed. This form is used to create the points that define the Dimensions and form the link with the 3D Model element.
The list on the left of the form sets how Dimension Points are created. The user must ensure that the correct option is selected in the list.
The default is that the Create button must be used for each point, but you can click on the symbol (to the right of the Create button) so the adjacent checkbox displays a tick. This allows you to create several points of the same type one after the other. Note: The symbol must be off if you want to create Dimension Points in different ways, or if you want to use the 3D Pos, Cursor or Match line positioning options. The user needs to click on Create and identify the elements to be dimensioned. This can be done in the 2D View by holding down the left mouse button (the pointer shape changes to a square) moving the pointer over the item and releasing the button. Note that when the pointer passes over a suitable item, that element is highlighted and its name is displayed in the Status Bar. Once the dimension string is completed, hit the ESC key on the keyboard.
7.3.2
Deleting dimension points
To delete a dimension point, identify it in the 2D view, to make it the CE. (It is advisable to check in the Draft Explorer that the element is highlighted.)
Either select Delete from the shortcut menu over the DPPT (Dimension Point) element in the Draft Explorer or select Delete>CE (Current Element) from the main menu bar.
In either case, click on Yes in the alert form that is displayed.
7.3.3
Modifying Linear Dimensions Graphically
To modifying linear dimensions graphically select modify mode from the icon on the 2D view. This mode is limited to changing the length of the projection lines, moving and rotating projection line text, moving and rotating dimension text. When in modify mode, the mode will be displayed as shown and the icon will change colour
www.aveva.com 70
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
7.3.4
Modifying Linear Dimensions
From the main bar menu select Modify>Dimension and a sub menu will be displayed with the following options • • • • • • • • •
Dimension Definition Dimension Colour & Font – allows the user to change the colour and font of the dimension Dimension Line – allows the user to modify the colour and style of the dimension line Projection Line - allows the user to modify the colour and style of the projection line Dimension Points Dimension Blanking Dimension Text Projection Text Sort Dimension Points
Selecting Dimension Definition will display the following form
This form is similar to the Create Form with one exception, and that is blanking. The purpose of blanking is to allow annotation to be shown clearly in crowded parts of a drawing, by removing an area of graphics.
Selecting Dimension Points will display the following form
The dimension point can be deleted, re-attached to a new design element, or additional dimension points can be created with the linear dimension.
Selecting POS from the toolbar, displays the following pull-down and allows the user to position the various parts of the dimension
Selecting PROJ from the toolbar, displays the following pull-down and allows the user to change the justification of the projection line text, change the projection line text and change the angle of the projection line text.
www.aveva.com 71
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Selecting DIM from the toolbar, displays the following pull-down and allows the user to change the angle of the dimension text. Selecting ATTS from the toolbar, displays the following pull-down and allows the user to change the attributes of the dimension Selecting DIR from the toolbar, displays the following form and allows the user to change the direction of the dimension.
7.4
Creating a Dimension (Example)
Display Drawing /DRWG_2/S1
Window to a small area of the drawing as shown.
Set the layer to Dimensions, there is only one as there is only one view.
www.aveva.com 72
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Select Create > Dimension > Dimension Toolbar
Select the Linear Tab
Select Orthogonal Continual / Chained Dimension
The Dimensions will be between Equipment.
Set Attachment to Owner so that the Dimension Point will be attached to the owner of the item identified.
Tick the box next to Create Button so the Draft will remain in create mode until is selected.
Select Create Identify an Equipment Primitive in each Equipment.
Select
www.aveva.com 73
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Select Pos > Dimension > Cursor from the Dimension Point Form. Reposition the Dimension using the Cursor.
Navigate to the Dimension Point on Equipment C1101 Using the Cursor on the Graphics View.
Select Pos > Clearance > Cursor from the Dimension Point Form. Reposition the Dimension Clearance using the Cursor.
www.aveva.com 74
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Select Att > Projection from the Dimension Point Form. Change the Line Style to Chained and Apply and Dismiss.
Select Proj > Line Text > CL Item Name from the Dimension Point Form.
7.5
Intelligent Text
It is very important that no “Free Text” is used on Draft Drawings, All Text must be derived from the Database. In the above example The Equipment Name has been automatically set from the database. Typically any attribute can be placed on the drawing by preceding it with a # symbol for example: #NAME, #EQUIP #POS etc. #NAME(c2:) means Name starting at Character 2. Navigate to the Dimension Point on equipment C1101 created above.
www.aveva.com 75
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Select Modify > Dimension > Projection Text
The Text is set to ~C #NAME(C2:) this mean Draw a Centre Line Symbol followed by the name that the dimension is attached to in this case an equipment starting at Character 2.
Select Intelligent Texts, Select #POSE, Append and Apply
The Projection Line Text will now shows the Centre Line Name and East position. Appendix B give more information on Intelligent Text, Text Symbols and Text Sub stringing.
www.aveva.com 76
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
7.6
Positioning Dimensions using Modify Mode
Dimensions, Dimension text and Projection Text can be positioned using Modify Mode. Select Modify Mode
Identify the Dimension and Drag it to the required Location, once in the correct location Click away (off) the Dimension. The Dimension Text is repositioned in the same way.
Remember to exit Modify mode .
www.aveva.com 77
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Exercise 10 – Dimensioning the drawing (Equipment Arrangement) Navigate to the sheet DRWG_1/S1 and dimension the drawing, similarly dimension both views on drawing /DRWG_2/S1. Create a set of dimensions across the centerline of all columns, and then dimension the equipment, locating from a column. Set the projection line text on the equipment dimensions to CL Equip Name, the name of the equipment will then be shown on the projection line. Modify the clearance and overshoot of the dimensions. The resulting drawing should look similar to the picture below. Change the projection line, line style to centre line representation, and set the projection line text to cl. Equip name.
www.aveva.com 78
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
www.aveva.com 79
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Exercise 11 – Dimensioning the drawing (Structural Arrangement) Navigate to the sheet DRWG_4/S1 and dimension the drawing. Create a set of dimensions across the centreline of all columns. Modify the clearance and overshoot of the dimensions. The resulting drawing should look similar to the picture below.
www.aveva.com 80
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
www.aveva.com 81
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Exercise 12 – Dimensioning the drawing (Piping Arrangement) Navigate to the sheet DRWG_3/S1 and dimension the drawing. Create a set of dimensions across the centreline of all columns, and then dimension the equipment and piping, locating from a column. Set the projection line text on the equipment dimensions to CL Equip Name and the projection line text on the piping dimensions to Pipe Name. Modify the clearance and overshoot of the dimensions. The resulting drawing should look similar to the picture below.
www.aveva.com 82
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
www.aveva.com 83
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
7.7 7.7.1
Angular dimensions Creating Angular Dimensions
Select Create>Dimension>Dimension Angular from the main toolbar and the following form is displayed. The user must ensure that the correct dimension layer is the CE. The default values are OK on the Create Angular Dimension form. Draft will prompt the user to identify the item that the angular dimension is to be attached to. For example DISH 1 of EQUIP C1101, as shown below:
1. Pick this Dish The origin will be here 2. Pick this Nozzle
3. Pick this Nozzle
The dimension will have its origin that is the point from which the angular dimension directions will radiate, at the origin of the element picked. The Linear/Angular Dimensions form is then displayed. This is the same symbol, and form as displayed for Linear Dimensions, and it is used in the same way. Switch on the click on Create. The user will be prompted to pick the items to be dimensioned. The Nozzles are identified in the order shown in the above illustration. (Selection is clockwise, because the setting is Clockwise in the Create Angular Dimension form.) On completion the user should click on the background or press the Esc(ape) key. The dimension will be drawn as shown below:
www.aveva.com 84
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
7.7.2
Modifying angular dimensions graphically
Modifying angular dimensions graphically is limited to changing the offset and standout distances. The offset of the dimension on C1101, so that the projection lines pass through the nozzles in question is done as before in Modify Mode. The dimension line is dragged to the required position and then fixed with a Click on the background or by pressing Esc. The dimension will then be drawn like this:
Remember to exit Modify mode .
7.8 7.8.1
Radial dimensions Creating Radial Dimensions
Radial dimensions are created in the same way. The Dimension Toolbar is displayed by selecting Create>Dimension>Dimension Toolbar from the main menu bar and the following form is displayed. Select the Radial tab. Check that On Item (not On Point) is displayed. and select the On Item option.
If not, right-click on the 6symbol
Select the required radius style. Refer to the Tooltips for the description of the available Radial dimensions.
You will be prompted to select the item to dimension. The dimensions will be created as shown in the following diagram
www.aveva.com 85
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
The Radial Dimensions form is then displayed. This form can be used to modify dimension.
The user can modify Radial Dimensions graphically in a similar way to modifying other dimension types.
www.aveva.com 86
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Exercise 13 – Creating Radial and Angular Dimensions Navigate to the sheet DRWG_5/S1 and dimension the drawing, giving all required linear, angular and radial dimensions on all 4 views.
L
Ensure that the correct layer is selected when dimensioning the views
Modify the dimensions to use different dimensions types. Modify the projection line linestyles and projection line colours. The resulting drawing should look similar to the picture below, additional dimensions will be required.
www.aveva.com 87
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
www.aveva.com 88
CHAPTER 8
8
Labelling
Labels are a form of drawing annotation, comprising text and/or graphics, associated with Design items. There are two types of Label, General Labels (GLAB) and Symbolic Labels (SLAB). The characteristics of these are as follows: • •
8.1
General Labels – consist of text derived from the design model. Symbolic labels – these are templates, (symbols containing intelligent text)
Labelling hierarchy
LAYE
GLAB DDNM
LIBY
SLAB DDNM
LALB TMRF TXTM
SYTM
Labels (GLAB and SLAB) elements are owned by Layers. Whenever a view is created a number of layers are created. Additional layers can be created as required. A GLAB has a DDNM attribute which will contain the design element being referenced. A SLAB has a DDNM attribute and a TMRF attribute which references a SYTM.
8.2
Creating / Modifying Layers
If additional layers are required select Create>Layer from the main pull down menu and the following form will be displayed. A default name will be given and the user must select the correct Layer Type.
www.aveva.com 89
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
To modify the Layer definition select Modify>Layer>Definition and the following form will be displayed.
Select the layer to modify from the displayed layers. The name, the Purpose and visibility can be modified
Select Attributes
On the Text TAB, the text height and definition can be modified.
On the Note TAB, the note line and hatch pattern can be modified.
8.3 8.3.1
Creating Labels Creating General Labels
Select Create>Label>General/Symbolic from the main bar menu and the following form is displayed.
Firstly select the Attach to dropdown. There are a number of menus and types to select from. The option selected will then be the only type for the current creation that a label can be attached to.
Create New, will create a new GLAB that will be connected to the element type selected in the Attached to dropdown.
Create Copy, will create a new GLAB, and the user will be prompted to identify an existing GLAB. If the element being identified has ppoints, the ppoint number to be attached to on the element can be entered in the PPOINT box, or clicking on Cursor, will prompt the user to identify a ppoint. If the element being identified has plines, the pline name to be attached to on the element can be entered in the PLINE box, or clicking on Cursor, will prompt the user to identify a pline. The distance along the section is defined as a proportion of the length, and any value less than 1 can be entered in the Proportion field. The rotation of the label can be specified.
www.aveva.com 90
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
The Blanking can either be on or off, by placing a check mark in the Blanking box. The margin around the blanking can also be specified. The attributes pull down has the following options
•
Text Settings – displays the following form, where the text attributes can be modified.
•
Text Contents – by default the contents of the label are set to the name of the labelled element. The contents can be changed and the following form is displayed. The position, alignment and justification can all be modified from this form. The text contents can be changed to any intelligent text by typing in the text into the form, or click on the Intelligent Texts button and examples are displayed for use.
•
Frame – displays the following form. The frame visibility can be turned off. The Label frame pen colour and style can be modified.
•
Leader Line – displays the following form. A number of options are available for inserting bends and gaps in the leader line. The Connection option allows the user to define the position of the leader line to the GLAB. The Attachment option allows the user to position the leader line away from the referenced design element. The Leader Line Colour and Style can also be modified.
www.aveva.com 91
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
8.3.2
Positioning General Labels using Modify Model
Modify mode is used to modify Dimensions, Labels and 2D Geometry by graphical interaction. There are many other non-geometrical modifications, such as changing the appearance of the text and linestyles that can only be carried out using the main menu Modify option. Entering and exiting Modify mode To enter Modify mode, you click on
the icon in the Drawing Display Window toolbar.
Draft will exit from Modify mode when you click on the Modify Mode button again, load a new Sheet or Library, update the design, model, picture or annotation. While you are in Modify mode, you can still control the view by zooming and panning, as normal. The label for modification is selected by left-clicking on it. It is then displayed in the current highlight colour. You can then modify the item you have selected, or select another item for modification. When you select the label, several hotspots are displayed. Initially the Attachment and Connection point hotspots for the leader line (if leader lines have been selected for the label) are on a single point, adjacent to the label. The display is like this: One of two arrows pointing to hotspots
Rotation hotspot
Attachment and Connection hotspots
Label outline
The arrangement of the hotspots becomes apparent when the label is moved from its initial position. The following illustration shows the label moved upwards and to the right: Arrow pointing to attachment hotspot
Attachment hotspot
Rotation hotspot
Connection hotspot
Arrow pointing to connection hotspot
Label outline
Bend point
The position of the label can be moved by left-clicking and dragging its outline. By left-clicking and dragging a hotspot you can modify the angle of the label or the geometry of the leader line. Once you have selected an item or hotspot in Modify mode, the Modify Mode shortcut menu can be displayed by clicking the right-hand mouse button. Options on this menu (see below), apart from the default
www.aveva.com 92
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
2D Cursor hit option, allow you to choose a position for a leader line hotspot with relation to an existing line, or lines, of the displayed engineering drawing. Menu options that are not applicable to the CE are greyed out.
8.3.3
Creating Symbolic Labels
DRAFT is supplied with a comprehensive set of libraries of standard Symbolic Labels which can be picked and added to a drawing. (Your Draft Administrator may have changed the supplied Libraries to company–specific ones.) The Labels can include intelligent text so that, for example, a Symbolic Label used on a Nozzle could display the Nozzle name and other information automatically. A Symbolic Label can only be added to a Layer. To add a Symbolic Label you must have a 2D Area view on display which includes the relevant VIEW containing a Design element. Select the Symbolic Label tab from the Create > Label >General / Symbolic from the Main bar menu. The library can be displayed or hidden. The Library form is used to display the standard Symbolic Labels supplied with DRAFT. Different Libraries may be specified, each of which contains a selection of Label Libraries.
The Library form will display those Symbolic Labels present in the Label Library whose name appears on the option button at the bottom of the form. Different libraries can be selected from the pulldown. Firstly select the Attach to dropdown. There are a number of menus and types to select from. The option selected will then be the only type for the current creation that a label can be attached to. Create New, will create a new SLAB that will be connected to the element type selected in the Attached to. The user will be prompted to identify a label from the library first, then to identify the design element in the view to which the label will be attached. Create Copy, will create a new SLAB, and the user will be prompted to identify an existing GLAB that is existing on the drawing.
www.aveva.com 93
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
If the element being identified has ppoints, the ppoint number to be attached to on the element can be entered in the PPOINT box, or clicking on Cursor, will prompt the user to identify a ppoint. If the element being identified has plines, the pline name to be attached to on the element can be entered in the PLINE box, or clicking on Cursor, will prompt the user to identify a pline. The distance along the section is defined as a proportion of the length, and any value less than 1 can be entered in the Proportion field. The rotation of the label can be specified The Blanking can either be on or off, by placing a check mark in the Blanking box. The margin around the blanking can be specified. The symbolic label can be scaled by entering values in the x and y
8.4
Hide/Show Labels
Label visibility can be toggled on/off. To hide a Label, select Modify>Label>Label Visibility from the main bar menu, and the Label Visibility form will be displayed.
Selecting the Scope button will allow the user to select labels for the whole sheet, a selected view or a selected layer.
The Hide and Show options allow the user to select All for all the labels, or Identified allows the user to select the label(s) by identifying them with the cursor in the view. The Display Hidden Labels button will show all hidden labels in a different colour to displayed labels.
8.5
Label Blanking
The geometry for the blanked area is determined by the geometry of the annotation element: for example, a circular label will define a circular area where no 3D graphics will appear. Overlapping 2D graphics, text and other annotation graphics will not be hidden.
L
Note that if Blanking is switched off, operations such as zooming and panning will be quicker.
Select Modify>Label>Label Blanking and the Blank Labs form is displayed.
The Modify Blanking is similar to the Label Visibility form. On the Blank Labs form, there is an option to define the margin around selected labels
.
www.aveva.com 94
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
8.6
Label Placement
This facility helps to ‘tidy up’ crowded areas of labelling, minimising Label overlap and leader-line crossing. As well as changing label positions this facility may also be used to change Label orientations, text justification, alignments, and the definition of leader-line shapes. Select Modify>Label>Label Placement: and the Intelligent Label Placement form is displayed.
8.6.1
Select
This area of the form allows you to Add or Remove Labels to be spread using a spreading list.
8.6.2
•
CE’s Labels – selects an individual label or all the Labels in the current view or layer.
•
Owner’s Labels – selects all the labels of the owner of the CE.
•
List – displays the Select List form. The user can select a predefined list or create a list for this activity.
•
Clear – clears the current selection.
•
ID Label – allows the user to select a series of labels
• •
ID Design – allows the user to select a series of labels attached to the identified design element. 2D Window – allows the user to select all the labels within a cursor defined window.
Position
Labels may be positioned Remote or Local. Having selected the required placement position clicking on the Definition button adjacent to your choice displays the relevant label definition form.
8.6.2.1 Remote The labels will be positioned around the view border. Clicking the Definition button will display the Remote Label Placement form. This form allows the user to set the positioning parameters for remote Label spreading to be set. •
Region - the Labels may be spread around a rectangular region defined by the Cursor. The coordinates of the region will appear in the X Y boxes, from where they may be modified.
•
View Margin - the Labels may be spread around a given margin of the current VIEW boundary.
•
Minimum gap between labels - defines the minimum gap between the labels.
•
Use - by default, all four sides of the VIEW border will be used to spread the Labels along, but one or more sides may be omitted if required.
www.aveva.com 95
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
•
Automatic Orientation - allows or suppresses automatic rotation of the Labels along the top and bottom sides of the view boundary.
An example of remote placement of labels is shown above.
8.6.2.2 Local The labels will be positioned around their significant design elements.
The Same option will cause the entered value to be copied into the other window, e.g. In the case below set X to 25 this will be copied to Y when the Enter button on the keyboard is used to confirm the setting. Selection of OK will have the same effect.
The spread offset of the Labels from their attachment points can be specified directly using the X Offset, Y Offset boxes or indirectly using a Radius and an Angle .
An example of local placement of labels is shown above.
www.aveva.com 96
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
8.7
Creating General Labels Example
Display Drawing Sheet /DRWG_1/S1
Select the Labels Layer, there is only one Layer as there is only one View.
Select Create > Label > General / Symbolic
Select General Labels Tab
Attach to Equipments
Select Create New
Identify several Equipments
L
Note the Label will be located at the Origin.
When finished
www.aveva.com 97
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Reposition The Label Using Modify Mode
The Attachment Point can also be modified
Select Text Contents
Add the Intelligent Text #POSE, #POSN and #POSU
Select Apply and Dismiss
www.aveva.com 98
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
8.8
Creating Symbolic Labels Example
Select the Symbolic Labels Tab
Attach to Nozzles
The Library Form will automatically be displayed.
Library
/DRA/MAS/LABELS/PRO
Lab/Symb Liby /DRA/MAS/LABELS/PRO/NOZZLE
Select Create New
Identify the Library Symbol with the Cursor
Identify Several Nozzles with the Cursor
when finished
www.aveva.com 99
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Reposition the Symbols using Modify Mode
Exercise 14 - Labelling Navigate to the sheet DRWG_4/S1 and label all the steel sections with the size of the steel profile using GLABs. Turn the default USER_Labs layer OFF. Create a new layer called SYMB_Labs and add some Symbolic Labels for the for the column lines. The text string to be entered in the text contents will be #:mdssizetag The tag will take the value from the UDA of the catref the component Turn off the leader line and frame, create the first label and select Relative in the Offset pull down, then use the Create Copy option
L
Ensure that the correct layer is selected when labelling the views
www.aveva.com 100
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Create SLABs for the column lines on the equipment arrangement drawings and piping drawing.
www.aveva.com 101
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
www.aveva.com 102
CHAPTER 9
9
2D Drafting
The 2D drafting facility within DRAFT is used for adding manually-drafted graphic and text details to drawings that have been generated from the Design database. The facility is not intended to be a used as a drafting package. There are three sets of menu options specific to 2D Drafting: • • •
Draw – enables the user to draw 2D Primitives and Local Symbols. Construct – enables the user to construct lines and other primitives using existing primitives. Edit - enables the user to change the attributes of a primitive, move primitives and nodes, insert gaps in lines, trim lines and arcs, rotate primitives, reduce a symbol to its basic components.
The basic geometric shapes and text that can be drawn are called Primitives. The primitives exist in the Draft hierarchy as members of NOTEs, VNOTs elements, or Symbol Templates (SYTMs). By default, the NOTE and VNOTE elements will be created automatically whenever a Sheet or Layer element is created, but the user can create additional NOTE and VNOTE elements if required. Primitives that exist as members of VNOTs may have their dimensions and positions defined in terms of 3D Design values.
9.1
2D Drafting Hierarchy
The following diagram shows the 2D drafting part of the Draft hierarchy. It shows the related elements and at what level in the hierarchy they may be created. All of these elements, with the exception of extra Layers, can be created as you add extra 2D elements to your Sheet or View.
SHEE Sheet Note VIEW
NOTE
LAYE View Note VNOT
All 2D Primitives
9.2
TEXP
SYMB
Creating Sheet Note and View Note elements
A Drawing Sheet will have been created with a number of Views and Layers. The Notes layer used for 2D drafting will own a View Note. 2D Primitives associated with a view will be added to the View Note. 2D Graphics and text associated with the main Sheet should be placed in a Sheet Note. www.aveva.com
103
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Select Create>Note from the main menu bar and the Create NOTE form is then displayed if the user is at a View element or above. The name can be left as default or changed as required.
Depending where the user is positioned in the hierarchy, a Sheet Note (NOTE element) will be created if at a View element or higher, a Layer Note (VNOT element) will then be created if at a Laye element or lower. As each Note is created, they are added to the list of Notes in the Layers toolbar. The displayed VNOT will indicate where primitives are to be subsequently created.
9.3
Creating primitives
To create primitives, first ensure that the required NOTE (or VNOT) is displayed. Select Draw>Primitives from the main menu bar and the 2D Draughting form will be displayed.
For all primitives except Symbols, the Point Construction Option Form will be displayed.
The prompt text displayed in this form instructs the user to the next step of action. The text will vary according to the type of primitive being created. Use the default option which is 2D cursor hit. This enables the user to position the selected primitive freehand. Pick the point(s) requested, by left-clicking the mouse with the pointer in the appropriate position(s) on the drawing. If the primitive is a graphic, it is drawn as the points are selected. Depending on the type of graphic, it may be necessary to click on Cancel on the Point Construction Option Form when the final point has been selected, in order to complete the graphic. If the primitive is Text, only one point is selected and the Modify Text form is then displayed.
The required text can be entered in this form. The font definition, colour etc. can be defined also.
Click on Apply to insert the text on the drawing, and then Dismiss the form.
Enter Modify mode
on the Main Display Window:
www.aveva.com 104
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
The general action is to select the primitive and then select and drag one of the hotspots until the required result is achieved. Click on the background to deselect. The hotspots available and the operations the user can carry out, depend on the type of primitive, and are described below under the names of the graphics.
9.4 9.4.1
2D Primitives Lines
From the Lines Tab on the 2D Draughting form, the following are available
9.4.2
•
- creates a single straight line
•
- creates multiple straight lines
•
- creates multiple orthogonal straight lines
•
- creates sketch straight lines
•
- creates a closed outline with straight lines
•
- creates a closed outline with curved segments
•
- creates an outline with curved segments
•
- allows the user to insert vertices by defining through points for outlines
•
- creates an arc with the user defining the start, end and through points
•
- creates an arc with the user defining the centre, start and angle
Shapes
From the Shapes Tab on the 2D draughting form, the following are available
•
- creates a circle with the user defining the centre and radius
•
- creates a circle with the user defining the diameter
•
- creates an ellipse with the user creating the left, right and top points
•
- creates a hexagon with the user defining the centre and radius
•
- creates a hexagon with the user defining the diameter
•
- creates a triangle with the user defining the corners
• •
- creates a diamond with the user defining the left, right and top points - creates a rectangle with the user defining opposite corners
www.aveva.com 105
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
9.4.3
Symbols
From the Symbols Tab on the 2D draughting form, the following are available •
9.4.4
– displays the 2D symbol and library form. The use of these is similar to the creation of symbolic labels. 2D symbols are attached to design elements.
•
- creates a table with the user defining the corner to corner
•
- creates a marker point
Text
From the Text Tab on the 2d draughting form, the following are available
9.5 9.5.1
•
- creates text with the justification top left
•
- creates text with the justification bottom left
•
- creates text with the justification bottom centre
•
- creates text with the justification bottom right
Construct Construct Group
Select Construct>Group from the main bar menu and the following form will be displayed.
This selection links all the selected elements together in such a way that Draft can track all the items owned by a group. Using groups allows the user to carry out the same operation on a number of elements simultaneously.
The selection of primitives to be included in the group may be carried out by any one of three methods: • • •
Identified – allows the selection of individual elements Crossing – allows the user to define a region selecting all elements that are either totally or partially within a defined area Window – allows the user to define a region selecting all elements that are totally within a defined area
After choosing the required method of element selection click the Add button, a prompt will be displayed informing the user to identify the element to be added to the group. After completion of the selection, all group members will change colour. The Clear button will remove all elements from the group and return them back to their original colour. Remove allows individual elements to be removed from the group and returned to the original colour. The Perform Action On Group button displays the following form, which is used to enter syntax, the operation to be actioned
www.aveva.com 106
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
nlpn 6 this will change the noteline pen to 6 by y20 moves all group elements 20 units in the +Y direction. The Filter button allows the setting up of selection criteria to help in only selecting the required elements. The user may not wish to select any arcs that are green from a particular Note/Vnote so by setting the Filter these items will not be selected.
9.5.2
2D Copy
Select Construct>2D Copy from the main bar menu. After choosing this option the user is prompted to identify the 2D primitives. To finish the selection click the Cancel button. The user will then be prompted to identify an origin point and then to position the copy
9.5.3
Repeat
Select Construct>Repeat from the main bar menu and the following options are available •
Offset – the user will be prompted to identify the 2D primitives. The Point Construction Option form will be displayed and the user will be prompted to identify the base point for displacement and the Offset Copy form will be displayed.
•
Rows and Columns – the user will be prompted to identify the 2D primitives. The Rows and Columns will then be displayed for the spacing, number of rows and columns required.
•
Polar – the user will be prompted to identify the 2D primitives. The user will be prompted to identify the centre of rotation point. The Polar Copy form will then be displayed.
www.aveva.com 107
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
9.5.4
•
Mirror - the user will be prompted to identify the 2D primitives. The Mirror form will then be displayed. To define the Mirror Axis the user may use one of three methods.
•
Cursor – define two points to generate a temporary line which will be used as the axis Identified Line – select a 2D primitive line that will be used as the axis X and Y co-ordinates – Enter the x and y co-ordinates
Fillet Arc
Select Construct>Fillet Arc from the main bar menu. The user will be prompted to identify the two joined lines to which the fillet is to be applied. The Fillet form will then be displayed. Enter the Radius, select whether the fillet is to be convex or concave and whether the lines are to be trimmed.
9.5.5
Chamfers
Select Construct>Chamfer Line from the main bar menu. The user will be prompted to identify the two joined lines to which the chamfer is to be applied. The Chamfer form will then be displayed. Enter the chamfer offsets, select whether the lines are to be trimmed.
9.5.6
Parallel Lines
Select Construct>Parallel Line from the main bar menu. The user will be prompted to identify the line to be parallel copied. The Parallel Line form will then be displayed. Enter the value of the offset, clicking Invert will change the direction of the copy.
9.5.7
Tangent Line
Select Construct>Tangent Line from the main bar menu. The user will be prompted to identify the arcs or circles for the tangent line.
This will draw a line tangent with two circles or arcs. The tangent will be drawn depending on where you select the circle. A form will be displayed that will allow you to reselect either points on the circles to define a different tangent. When the tangent line is between arcs the user will also have the option to trim the arc to the connection point of the tangent line.
www.aveva.com 108
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
9.5.8
Ray Line
A Ray Line is a form of construction line. Select Construct>Ray Line from the main bar menu, and the Point Construction Option form will be displayed. The user will be prompted for two points, the first will be the start point and the second will be the through point. The line will continue to the edge of the sheet. The Ray Line form will then be displayed which allows the user to change the X and Y values of the through point and the angle of the line. The Edit>Line Trim can be used to cut the line back from the sheet edge.
9.5.9
Constructed Line
Select Construct>Constructed Line from the main bar menu. The Point Construction Option form will be displayed. This option allows the user to draw an infinite line through two given points. It is also possible to use the Edit>Line Trim option to cut the line back from the sheet edge.
9.5.10 Bisector Line This option will construct a line that bisects the angle formed by two selected line. The bisector will start at the intersection of the two selected lines and continue to the sheet edge. Select Construct>Bisector Line from the main bar menu. The user will be prompted to identify two bisected lines. The Bisector Line form will be displayed. The user can modify the Length of the line, the X and Y values of the through point. A Bisector may also be trimmed by using the Edit>Line Trim option.
9.5.11 Local Symbols Select Construct>Local Symbol from the main bar menu. The user will be prompted to Select the 2D primitives for the local symbol. The Point Construction Option form will then be displayed, the user will be prompted to identify the origin for the local symbol.
The Create SYTM form will then be displayed. Click on OK and the Local Symbols form is displayed.
L
NOTE: Local Symbols created in the hierarchy of the current drawing and are not available outside of this drawing.
www.aveva.com 109
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
9.6
Edit
9.6.1
Edit>Primitive
This allows the user to alter the attribute settings for the selected primitive. Before selection of this option the user must have already selected the primitive to be edited. Once selected the Modify ‘primitive type’ Attributes form will be displayed to allow the resetting of the attributes. When finished click Apply. Reset will return the last saved settings.
9.6.2
Edit>Move Primitive/Node To
Note that when the Edit>Move Primitive/Node To is selected, all nodes on all primitives will be shown to aid selection. Once selected, depending on the option selected from the submenu, a form will be displayed for you to position where the node should now be positioned.
L
Note centres of arcs, circles etc. are not moved.
9.6.3
Edit>Move Primitive By
This allows the user to move the whole primitive by a distance which is either calculated by the entering of two cursor points or entering the amount to move in the X and Y directions.
9.6.4
Edit>Move Node By
This allows the user to reposition a Node on a primitive thereby changing the shape of the primitive.
9.6.5
Edit>Line Gap
Allows the creation of a Gap, which may have a length of Zero, Default or defined by its Start and Finish points.
9.6.6
Edit>Line Trim
Is used to Trim a line or arc to another arc or line, which is to be selected.
9.6.7
Edit>Rotate
This will allow the selected element/s to be rotated about a selected point by a user defined angle.
9.6.8
Edit>Demolish Symbol
This will break the links created when defining a Local Symbol
9.6.9
Edit>Action Group
This will call up the Perform Action on Group form where the user can enter syntax to perform a particular action on the whole group.
www.aveva.com 110
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
9.7
Utilities (2D)
9.7.1
Load Text
Select Utilities>Load Text from the main bar menu and the Load Text From File form will be displayed. If the text file to be loaded is not in the ‘Local’ (i.e. current) directory, type the appropriate directory pathname into the Directory text box and press Enter.
L
Note: the file must be a text file
The Files scrollable list lists all the files in the current directory. Select the required file. The name of the selected file will appear next to Text File. If the user wants to position the (origin of the) text using the pointer, select Cursor from the option button to the right of Position, then click on the desired Sheet position on the display. The Sheet co-ordinates of the chosen point will be displayed in the Position text boxes. If the user wants to position the (origin of the) text using Sheet co-ordinates, type the required coordinates into the Position text boxes. If required, use the controls at the bottom of the form to vary the text Colour, Font, Justification, Character Height, Spacing or Line Spacing.
9.7.2
Sketch Drafting
Select Utilities > Sketch Drafting from the main bar menu and the Sketch Drafting 2D attributes form will be displayed This form will allow the setting of default pens, text justification, character height, alignment, character spacing, and line spacing. The user can also set the Fill pen to be On allowing cross hatching to be used. The settings on this form can be set to be used automatically or on request. To use automatically make sure that the following icon is checked:
www.aveva.com 111
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
9.7.3
Dynamic Primitives
Select Utilities > Dynamic Primitives from the main bar menu and the Modify Primitives form will be displayed
This form will display the attributes of the selected primitive. To change any of the settings simply enter the required value into the correct field and after the Enter key has been pressed the primitive will change to reflect the new values entered.
9.8
Creating 2D Primitives Example
Display Drawing Sheet /DRWG_1/S1
If the 2D Annotation is associated with a View it should be placed on a View Note (VNOT) but if the 2D Annotation is general text it should be created in a Sheet Note.
9.8.1
Creating a New Note
Navigate to Sheet /DRWG_1/S1 Create > Note Accept the default Name The Drawing Sheet will now have two 2D Layers one for the Sheet and one for the View.
9.8.2
Added 2D Text to a View Note
Select 2D Draughting and Layer /DRWG_1/S1/V1/USER_Notes
www.aveva.com 112
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Select Draw > Primitives
Select Text Tab
Select Bottom Centre Justified Text
Position the Text towards the Bottom of the View Using the Cursor
Colour black (15)
Height 20
Intelligent Texts…
Select Drawing
VTitle #VTITL
Append
www.aveva.com 113
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Select Apply and Dismiss
The view title will be displayed as shown below.
9.9
Adding 2D Primitives to a Drawing Sheet Note
Display Drawing Sheet /DRWG_1/S1 and window to a suitable area.
Select 2D Draughting and Layer /DRWG_1/S1/SN1 Select Draw > Primitives
Select Lines Tab
Select Single Straight
Draw Lines and text as required
www.aveva.com 114
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
2D Primitive Attributes can be changed by Selecting Edit > Primitive
A form relative to the primitive type will be displayed.
www.aveva.com 115
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Exercise 15 – 2D Draughting Navigate to the sheet DRWG_5/S1, create a title for each view, ensuring that each text element is on the correct VNOT. Create 2D primitives using all of the options on the Draw toolbar. Experiment with the different options on the Point Construction Option Form. Click on the different types of primitives you created in 2 and edit them in turn by selecting Edit>Primitives… from the main toolbar. Note how the edit form changes to suit the primitive being edited. Experiment with the construction options, e.g. 2D Copy, Mirror…, Chamfer Line…, etc. in the Construct pull-down on the main menu. Delete all the primitives on the views. Add some section marks using 2D symbols. Create a text file containing some general notes using TextPad or WordPad. Create a Sheet NOTE and import the text file as General Notes using Utilities>Load Text… from the main menu, positioning the notes at the top of the Notes column on the right-hand side of the drawing. Create a revision triangle, containing a suitable revision identifier, as a Local Symbol. Create a revision ‘cloud’ around some Design elements in the views and add the revision Local Symbol to each cloud.
www.aveva.com 116
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
www.aveva.com 117
CHAPTER 10
10 Section Planes 10.1 Section Planes DRAFT gives you the ability to construct sections through specified Design items, the results of which can be displayed at VIEW level. All Planes are database items and can therefore be used with more than one VIEW. There are three types of section planes • • •
Flat Plane Perpendicular Plane Stepped Plane
This module covers Flat Planes only. For information on Perpendicular and Stepped Planes Please refer to TM-1206 Drawing Production (Advanced). The Section Mode option button, on Create>View or Modify>View, can be set to Omit Fractional Components, in which case, any components which are not completely inside the sectioned View will be omitted.
On the limits Tab, if the box is checked, section planes will be created automatically.
www.aveva.com 118
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
All Planes are created and held within a Library structure and are owned by a Planes Library (PLLB). To use a plane to produce a sectioned view of part of the Design, you need to create a View Section (VSEC) element (starting at the relevant VIEW), which will refer to the appropriate type of plane element in the Planes Library. A Planes Library is always created automatically (if the Drawing does not already have one) whenever you make one of the Create>View>Section menu selections. The appropriate type of Plane is then created as a member of the Planes Library, being referred to by the VIEW Section.
L
NOTE: if the view type is wireline, the view will not be sectioned
10.2 Creating Flat Planes Starting at VIEW level, select Create>View>Section Flat from the main bar menu. A View Section element will be created automatically, and a Create a Flat Plane form will be displayed. The Name text box will contain the automatically assigned Plane name, which can be changed.
Select the required Plane positioning method from the option button located to the right of the Position button, then click on the Position button. •
Explicit – the Explicit Plane form is displayed. Enter the required co-ordinates.
• • •
ID Cursor – an appropriate message will be displayed. Click on the required Design item ID P-Point – an appropriate message will be displayed. Click on the required p-point Cursor – an appropriate message will be displayed, identify a 3D point as required
The Cutting option button lists the available Drawlists. The items to be cut by the plane will be those referred to by the selected list. If World is selected, all items in the owning VIEW’s Drawlist will be cut. Direction defines a vector normal to the plane, set to the current VIEW direction by default. If you wish to change this, type the new direction into the text box. Centerline Mode. If this is active then everything included on the Drawlist except the Center-Line of pipes if displayed will be Cut. Retain Data option button lists the available options for defining which side of the cut items are to be discarded from the display. The default In front of Plane means that everything on the observer’s side of the plane will be discarded. Select as appropriate.
www.aveva.com 119
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Having clicked on OK, select Graphics>Update>Design from the Draft General bar menu in order to update the VIEW contents.
10.3 Modifying Flat Planes Note that you must be at VIEW level or below to modify a Flat Plane. Select Modify>View>Section Flat from the main bar menu and the Modify a Flat Plane form is displayed
This form is almost the same as the creation form. The difference is that there are two extra buttons on this form. These are Sketch and Erase buttons. Sketch will draw the profile of the cutting plane being used. Erase will remove from the screen the drawing aids showing the cutting plane. Having clicked on Apply, select Graphics>Update Design from the DRAFT menu bar in order to update the VIEW contents.
10.4 Flat Plane Example For the purposes of the training a Drawing Sheet has been created with one view having /EQUIP.ZONE and /STRU.ZONE in the Drawlist.
www.aveva.com 120
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
The Section Plane is created as follows:
Create > View > Section > Flat Cutting World Direction –Z Retain Data In front of Plane
Position Explicit…
West 312660 North 303544 Up
107100
Apply and Dismiss OK the Create a Flat Plane Form Select Graphics > Update Design from the Draft Main Menu.
The above drawing shows the top level equipment removed.
www.aveva.com 121
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Exercise 16 – Section Planes Create a sheet of any size that contains four views. The views should have viewing directions of North, East, Down and Iso3 respectively. Create a Drawlist that contains the equipment element P1501A from the STABILISER Site and the site /WALLSITE. Set the Drawlist Ref… for each view to this Drawlist. Create Flat Planes in each view with a direction of your choice. Retain the data In Front of Plane in all cases and note the effect on the Design elements in the views. Modify all planes to retain data Behind Plane and note the effect on the Design elements in the views. Modify the Direction of each plane in turn and note the effect on the Design elements in the view. Create two separate Drawlists, one containing /P1501A and the other containing the WALLSITE. The following example shows a Flat Plane cutting Drawlist that contains the WALLSITE Only.
In one of the orthogonal views delete the existing Flat Plane and create two new Flat Planes with directions perpendicular to each other, e.g. one North and one East. Set one plane to cut the Drawlist containing /P1501A and the other plane to cut the Drawlist containing the WALLSITE. Update the view graphics and note the effect of the two planes.
www.aveva.com 122
Appendix A
Appendix A Wireline
Modelled Wireline
www.aveva.com 123
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Local Hidden Line
Global Hidden Line
www.aveva.com 124
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
Universal Hidden Line
www.aveva.com 125
AVEVA Plant (12 Series) Drawing Production (Basic) TM-1002
www.aveva.com 126
Appendix B Appendix B Intelligent Text Intelligent Text can be automatically extracted from the Design, Catalogue or Drawing databases to replace the Drawing Intelligent text code words, which begin with a # character. See below for examples. For this we will use as an example a pipe name of /ZONE-4/BRANCH-6 Text
/
Z
O
N
E
-
4
/
B
R
A
N
C
H
-
6
Character No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Intelligent Text Format
Result
#NAME
/ZONE-4/BRANCH-6
#NAME(C2:)
ZONE-4/BRANCH-6
#NAME(C2:7)
ZONE-4
#NAME(P-2:)
-6
#NAME(P/2:)
/BRANCH-6
#NAME(P2:)
/BRANCH-6
#NAME(P/2:)(C2:)
BRANCH-6
#<
Starts underline
#>
Ends underline
#
