User Guide
MONGOOSE PRO SHAKER
UL/ATEX Approved Worldwide Headquarters P.O. Box 42842 Houston, TX 77242‐2842 Tel: 281‐561‐1300 Fax: 281‐561‐1441 www.miswaco.com E‐mail:
[email protected]
Manual Part #: 9091120 (‐‐)
M-I SWACO
MONGOOSE PRO USER GUIDE
DISCLAIMER
Recommendations made by M‐I SWACO are advisory only. M‐I SWACO shall not be liable under any guarantees or warranties, expressed or implied, in any manner or form, AND ALL WARRANTIES, EXPRESSED OR IMPLIED, ARE HEREBY SPECIFICALLY EXCLUDED, and M‐I SWACO shall not be liable for the failure to obtain any particular results from the use of any recommendation made by it or from the use of this material. In no event shall M‐I SWACO be liable for incidental or consequential damages.
ASSEMBLIES COVERED IN MANUAL This user guide is for assemblies 9675xxx. NOTE: Information included within this manual supports multiple configurations and/or models. See Installation, Operation & Maintenance (IOM) manuals for further details.
© Copyright 2011 M‐I L.L.C. Publication date: July 2011 * Mark of M‐I L.L.C. All other products, brand, or trade names used in this publication are the trademarks or registered trademarks of their respective owners. All rights reserved. This publication is the property of, and contains information proprietary to M‐I L.L.C.. No part of this publication may be reproduced in any form or by any means, including electronic, mechanical, or otherwise, without the prior written permission of M‐I L.L.C.. Information contained within this publication is subject to change without notice.
ii
9091120(--)
MONGOOSE PRO USER GUIDE
M-I SWACO
TABLE OF CONTENTS Item Description Section 1.0 Introduction Intended Usage Symbols Safety Personal Protective Equipment (PPE) Functional Description Fluid Distribution Systems Section 2.0 Preparation Unpacking Lifting & Handling Equipment Location External Power/Electrical Connections Preservation & Storage Decommissioning Procedures Section 3.0 Operating Instructions Adjustable Equipment Parameters Shaker Speed Equipment Start‐Up Controlled Shutdown Screen Handling Section 4.0 Preventive Maintenance Safety Related Maintenance Procedures Motor Maintenance Isolation Springs Greasing Deck Adjustment Jack Recommended Preventive Maintenance Schedule Section 5.0 Troubleshooting Section 6.0 Maintenance Procedures Screen Gasket Replacement Isolation Spring Replacement Procedures Vibrator Removal & Installation Cable Gland Assembly Instructions Elevator Jack Replacement Shaker Washer Down Procedures Surface Corrosion Removal Section 7.0 Rig Critical Recommended Spare Parts List Section 8.0 Electrical Schematics
Page Number 2‐8 2 2‐3 4 4 5 5‐8 9‐13 9 9‐10 10 11‐12 13 13 14‐17 14 15 16 17 17 18‐21 18 18‐19 20 20 21 22 23‐30 23 24 24‐25 26‐27 28 28‐29 30 31‐40 41‐44
9091120(--)
1
M-I SWACO
MONGOOSE PRO USER GUIDE
SECTION 1.0: INTRODUCTION INTENDED USAGE This documentation is intended for use by field engineering, installation, operation and repair personnel for the proper installation and maintenance of equipment manufactured by M‐I SWACO. Every effort has been made to ensure the accuracy of the information contained herein. M‐I SWACO will not be held liable for errors in this material, or for consequences arising from misuse of this material.
SYMBOLS Notes, Cautions & Warnings Notes, cautions and warnings appear throughout this manual to provide additional information and to advise on specific actions to protect personnel from potential injury or fatal conditions. They also inform of actions necessary to prevent equipment damage or conditions that may void equipment warranties. This symbol draws attention to safety measures which MUST be observed to ATTENTION prevent DAMAGE to equipment. This symbol draws attention to safety measures which MUST be observed to CAUTION prevent an ACCIDENT from occurring. This symbol draws attention to safety measures which MUST be observed to prevent PERSONAL injury. WARNING NOTE: This symbol draws attention to general operating notes which should be especially observed. Packaging
The symbols that may be shown on the package are noted below. The meaning for each symbol is defined below its respective symbol:
2
9091120(--)
MONGOOSE PRO USER GUIDE
M-I SWACO
Safety Warning Icons & Explanations Refer to the illustrations below to easily recognize safety concerns and responsibilities to follow. Each illustration is accompanied with an explanation for the user to be readily alert for and pay attention to during operation and maintenance of the equipment.
TABLE 1.1: SAFETY WARNING ICONS & EXPLANATIONS ELECTRICAL: Electrical wire to hand with electricity symbol running through indicates shock hazard is present.
HEAVY PARTS: Hand with heavy object on top indicates heavy parts can crush and harm.
HEAVY PARTS: Foot with heavy object on top indicates heavy parts can crush them.
MOVING PARTS: Human figure with an arm caught between gears indicates moving equipment parts present a danger to life or limb. CHEMICAL: Drops of liquid on hand indicates material will cause burns or irritation to human skin or tissue.
MOVING PARTS: Hand with fingers caught between gears indicates moving equipment parts present a danger to life or limb. EXPLOSION: Rapidly expanding symbol indicates material may explode if subjected to high temperatures, sources of ignition or high pressure. POISON: Skull and crossbones indicate that a material is poisonous or is a danger to life.
FIRE: Flame indicates material may ignite and cause burns.
LOCK OUT: Open lock with direction arrow indicates to operator to ensure ALL input power sources are locked out and tagged out according to regulation. FLYING PARTICLES: Arrows bouncing of face indicates parts/particles flying through air will harm face and present a danger to life or limb. EAR PROTECTION: Headphones over ears indicate noise level will harm ears.
HOT: Hand over flame indicates that surfaces may be hot.
VAPOR/FUMES: Human figure in a cloud indicates that material vapors/fumes present a danger to life or limb.
HELMET PROTECTION: Arrow bouncing off head with helmet indicates falling parts present a danger to life. ELECTRICAL: Electrical wire to arm with electricity symbol running through human body indicates shock hazard is present.
READ MANUAL: Wrench over book indicates the necessity to read the instructions before performing any operations.
9091120 (--)
3
M-I SWACO
MONGOOSE PRO USER GUIDE
SAFETY Equipment manufactured by M‐I SWACO is installed and operated in a drilling rig environment involving hazardous operations. Proper care is important for safe and reliable equipment operation and rig personnel safety. Operation and service procedures described within this manual are recommended methods of performing proper operations and safety methods. Consult Local or National codes for any other safety regulations required for this type of environment. Safety Procedures
CAUTION To avoid injuries to the personnel or damage to equipment, read the following procedures before attempting any installation or maintenance procedures on M‐I SWACO equipment.
All personnel performing installation, operations and maintenance procedures on this equipment should be trained on rig safety, operations and maintenance of this equipment.
WARNING
Initiate a controlled shutdown before starting ANY parts replacement procedure. Lockout / tag out the unit.
Do NOT perform maintenance or repairs to equipment while unit is in operation. Have a certified electrician ensure power supplies are isolated BEFORE performing any maintenance on unit. Wear Personal Protective Equipment (PPE). Clean all parts and work area. Block up and secure heavy parts BEFORE working beneath unit or parts. When heavy lifting is involved, always seek assistance. Ensure all tools, old parts, nuts, bolts washers, etc. are removed BEFORE restarting unit after maintenance.
PERSONAL PROTECTIVE EQUIPMENT (PPE) All personnel working on or around M‐I SWACO equipment MUST wear Personal Protective Equipment (PPE), which includes an approved hard hat, safety glasses/shield; gloves and outer garments. Local or National codes require different and/or additional PPE apparel. Comply accordingly.
4
9091120(--)
MONGOOSE PRO USER GUIDE
M-I SWACO
FUNCTIONAL DESCRIPTION The shaker’s basic function is to provide primary solids removal from both oil based mud (OBM) and water based mud (WBM) during drilling operations. The Mongoose Pro* enables operators to meet a wide variety of drilling conditions with four screens per basket, along with an adjustable deck angle that allows flexible control of fluid pool depth and beach length. The unique motor mounting of the two motor shaker vibrators produces a true linear motion adjustable dual motion drive allowing the user to switch between linear and balanced elliptical motion while unit is in operation. Each unit has a fluid distribution box. Options include:
Header Box Possum Belly with Butterfly Valve and Bypass Possum Belly with Knife Gate and Bypass NOTE: Refer to the Installation, Operation and Maintenance manuals for further details.
FLUID DISTRIBUTION SYSTEMS Shaker with Header Box
The fluid distribution system is at the rear of the shaker basket and is mounted above the screen deck (Refer to Figure 1). Fluid is redirected from the inlet line through the header box into a half pipe at the rear of the basket. Since fluid distribution is mounted above the screen deck, no trap exists to collect solids. As fluid passes through the diverter box, it sweeps the box clean.
Figure 1 Carbon Steel Header Box
9091120 (--)
5
M-I SWACO
MONGOOSE PRO USER GUIDE
Shaker with Possum Belly with Butterfly Valve Bypass
The butterfly valve is located below the main inlet on the possum belly (Refer to Figure 2). Use to manually open or close the bypass. When CLOSED, fluid flow is directed through the possum belly to the shaker bed. OPEN the bypass by turning butterfly valve 90°. When butterfly valve is opened, fluid is redirected into the skid, bypassing the screens. Figure 2 Possum Belly with Butterfly Valve
Shaker with Possum Belly with Knife Gate Bypass
The pivoting knife gate for single shakers is manually raised or lowered to operate the bypass (Refer to Figure 3). When the knife gate is opened, fluid is redirected into the skid, bypassing the screens.
Figure 3 Possum Belly with Knife Gate
6
9091120(--)
MONGOOSE PRO USER GUIDE
M-I SWACO
Dual & Triple Shakers with Common Possum Belly with Knife Gate Bypass The knife gate is controlled by a single, turning hand wheel (Refer to Figures 4 & 5). When the knife gate is opened, fluid is redirected into the skid bypassing the screens. The manually operated slide gates are also used to control the flow rate.
Figure 4 Dual Shaker with Common Possum Belly with Knife Gate
Figure 5 Triple Shaker with Common Possum Belly with Knife Gate
9091120 (--)
7
M-I SWACO
MONGOOSE PRO USER GUIDE
Quad Shakers with Feed Manifold Assembly, Header Boxes & Butterfly Valve Bypasses Mud feeds into the back of the feed manifold assembly with the flow evenly distributed to each of the header boxes (Refer to Figure 6). Butterfly valves located at each header box are used to open or close flow to a particular shaker. Butterfly valves located at the top of the feed manifold are used to close off flow to shakers enabling the use of a cement bypass.
Figure 6 Quad Shaker with Feed Manifold Assembly, Header Boxes & Butterfly Valve Bypasses
8
9091120(--)
MONGOOSE PRO USER GUIDE
M-I SWACO
SECTION 2.0: PREPARATION UNPACKING Inspect all goods as received from shipping company BEFORE setting up and operating the shale shaker. Report a claim for damage or loss immediately to both the carrier and M‐I SWACO. Also check bill of lading for any separately shipped items, including manuals and CDs. Once an order is confirmed as received completed in an undamaged condition, installation can begin.
CAUTION Special shipping brackets are used to retain the basket onto the skid during shipping. Keep them secured to the unit until it is placed in its final location. Keep these brackets safe for future movement or long term storage of the Mongoose Pro.
The Mongoose Pro* is equipped with special shipping brackets for the front and rear of the shaker basket assembly. To remove the shipping brackets, use a 30mm socket wrench to loosen the bolts on each bracket. Store the brackets on the unit, using the integrated bolt holes on the skid to hold the brackets in place (Refer to Figures 7 & 8).
Figure 7 Front Shipping Bracket Engaged (Left) and Stored (Right)
LIFTING & HANDLING
Always use trained personnel for lifting and loading operations. Ensure lifting equipment is suitable for purpose and is certified where necessary.
Use the four lifting lugs located at each of the four corners of the unit. A label shown in Figure 9 indicates location of each lifting lug on the unit.
Figure 8 Rear Shipping Bracket Engaged (Left) and Stored (Right)
ATTENTION Perform structural checks on the deck beams to ensure they can support applied loads (twice the shaker weight) of equipment.
9091120 (--)
Figure 9 Lifting Lug Label
9
M-I SWACO
MONGOOSE PRO USER GUIDE TABLE 2.1: UNIT WEIGHTS & DIMENSIONS Unit Description Single Mongoose Pro PT Dual Mongoose Pro PT Triple Mongoose Pro PT Quad Mongoose Pro PT
Approximate Unit Dry Weight 1560 kg (3430 lbs.) 3886 kg (8550 lbs.) 5871 to 6110 kg (12,943 to 13,471 lbs.) 8709 to 9162 kg (19,200 to 20,200 lbs.)
Unit Dimensions 3044 mm x 1749 mm x 1394 mm (119.8” x 68.9” x 54.9”) 3150 mm x 3689 mm x 1330 mm (124” x 145” x 52.4) 3150 mm x 5842 mm x 1433 mm (124” x 230” x 56.4”) 3686 mm x 7579 mm x 2586 mm (145.1” x 298.4” x 101.8”)
EQUIPMENT LOCATION
The shaker is supplied with an integral skid and is positioned directly onto the deck or above sand traps as required. Install, operate and maintain equipment only with qualified personnel. Locate unit at proper site.
If unit is installed indoors, adequate ventilation is necessary. Ventilation set‐up may be completed by qualified M‐I SWACO personnel or by the customer.
The carbon steel feeder assembly has an installation guide painted on the rear of the feeder for mounting the inlet pipe which can accommodate 6”, 8” and 10” inlet pipe sizes (Refer to Figure 10).
The units are designed on a modular basis and can be disassembled into individual components for easier installation.
Figure 10 Piping Installation Guide (Arrowed)
TABLE 2.2: WEIGHTS FOR MODULAR COMPONENT Unit Description Single Mongoose Pro PT
Basket Assembly (Without Motors) 618 kg (1360 lbs.)
Dual Mongoose Pro PT Triple Mongoose Pro PT Quad Mongoose Pro PT
10
518 kg (1141 lbs.)
Skid 329 kg (725 lbs.) 1531 kg (3375 lbs.) 1497 kg (3300 lbs.) 2388 kg (5264 lbs.)
Motors
Possum Belly
Header Box
128 kg (282 lbs.)
193 kg (425 lbs) 545 kg (1202 lbs.) 545 kg (1202 lbs.) 1597 kg (3521 lbs.)
Carbon Steel 128 kg (283 lbs.)
9091120(--)
MONGOOSE PRO USER GUIDE
M-I SWACO
EXTERNAL POWER/ELECTRICAL CONNECTIONS (UL PANEL) Start-Up
NOTE: Refer to the Wiring Schematics in Section 8 of this User Guide.
Inlet port is located on side of control box (Refer to Figure 11). Remove plug seal on control panel box. Insert cable gland and wires through connection port.
NOTE: The green wire is the grounding lead and the brown, white/grey and black wires are all LIVE power leads.
Attach (crimp) an eyelet wire connector to the wire ends of the grounding cable (Refer to Figure 12). Loosen screws on power distribution box. Insert bare wire endings of the power leads into power distribution box. Retighten screws on power distribution box once wires are in place. Inspect o‐ring seal on door surface. Replace if damaged. Install ALL bolts to completely close door.
Figure 11 Inlet Port (Circled)
Three Power Source Cables (Power Leads)‐ Inserted Into Power Distribution Box
Cable Gland Connection Port (Interior View of Control Box)
Grounding Cable
Figure 12 Interior View of Control Box
9091120 (--)
11
M-I SWACO
MONGOOSE PRO USER GUIDE
Initializing Procedures
WARNING Perform lockout / tag out procedures to isolate the unit from the rig power supply.
Remove vibrator covers and verify counter‐weight (Refer to Figure 13).
NOTE: The motor closest to the feed end of the unit is a fixed weight motor; the motor closest to the discharge end of the unit is a swing weight motor.
Figure 13 Fixed Weight (Left) & Swing Weight (Right)
Reassemble one cover to each vibrator; leaving one cover off of each vibrator. Bump start motors to check rotation.
WARNING Keep all guards in place at all times to avoid exposure to parts rotating at high speeds. When the power is ON, severe injury can occur if hands or feet reach inside the unit.
NOTE: Bump start motors by pushing START button located on control panel. Next, quickly push STOP button on control panel.
Check direction of top counter‐weights. Vibrators should rotate as indicated on the Motor Rotation Nameplate (Refer to Figure 13).
Figure 14 Motor Rotation Diagram
WARNING Perform lockout / tag out procedures to isolate rig power supply.
WARNING All components inside the control box are LIVE and present a shock hazard.
12
Reinstall all counterweight covers. Start up unit and run for approximately one hour. Allow enough time for bearings to reach normal running temperature. Using an amp meter, verify the current drawn by the vibrators from the control panel matches the specifications on the vibrator nameplate (a clamp‐on current meter is recommended). Clamp around each motor cable lead to get current readings (Refer to Figure 15). Bolt control panel cover on panel.
Figure 15 Amp Meter
9091120(--)
MONGOOSE PRO USER GUIDE
M-I SWACO
PRESERVATION & STORAGE Storage of Non-Commissioned Equipment Equipment can be stored (upon arrival) in the shipping crate for a 12 to 24 month preservation period. Do NOT expose equipment to dust, vibration or extreme weather conditions (such as heavy rain). If unit has been removed from original crate, cover with a tarpaulin during any preservation period. Every 1‐3 months, examine the motors. Remove their weight covers and rotate the counterweight to preserve the bearings. Storage of Commissioned Equipment
Reinstall original shipping brackets to protect equipment. When disconnecting power connections to control station and motors, plug all inlets with an appropriate fitting to keep water/moisture from entering. Do NOT leave any electrical connections open and exposed. Add anti‐condensation packs to motor J‐Boxes and control station. Install and seal all control station doors and J‐Box Covers.
DECOMMISSIONING PROCEDURES
WARNING When initiating the decommissioning procedures on the Mongoose Pro, shut off and lock out power before removing guards (brackets, skirt, etc). Follow all local and national electrical codes. Failure to comply could result in severe personal injury or property damage. Lockout of power MUST be completed by a certified electrician.
Wash unit and remove screens from shaker. Disconnect flow line from feeder and main power lines from control panel. Attach shipping brackets to baskets and skid. Move or transport shaker via lifting points indicated on skid.
9091120 (--)
13
M-I SWACO
MONGOOSE PRO USER GUIDE
SECTION 3.0: OPERATING INSTRUCTIONS
ADJUSTABLE PARAMETERS DURING NORMAL OPERATING CONDITIONS Screen Selection
Selection of screen mesh depends on a number of factors: flow rate, fluid condition, formation, rate of penetration (ROP), fluid type and number of shakers. Use the finest screen possible to ensure optimum performance to the relative screen life. Flow Rate
1‐1/4” Nut
Adjust flow rate to maintain a constant pool level on all shakers used. The optimal fluid end point is 75% of the screen surface. Basket (Deck) Angle
The basket deck angle is manually adjustable between ‐3 degrees and +3 degrees (Refer to Figure 16).
NOTE: Shut down of shaker before changing deck angle is NOT necessary.
Adjustable Between ‐3 Degrees & +3 Degrees
ATTENTION Do NOT use air/pneumatic ratchet or wrench to adjust the deck angle jack.
Figure 16 Basket (Deck Angle)
CHANGING BASKET (DECK) ANGLE
IMPORTANT: Do NOT adjust more than 2 degrees per side when changing deck angle.
Use a manual ratchet, wrench or screen clamping wedge to adjust the 1‐1/4” nut located on top of jack. Adjust each side to desired position. Always set each side to the SAME angle. Locate manual jacks on discharge end of shaker and set basket at any angle between the highest and lowest angle. Reset fluid end point by adjusting basket angle or by careful selection of mesh size.
NOTE: Always operate shaker with lowest possible basket angle to meet capacity requirements. A steep incline results in screen overload and decreased screen life.
14
9091120(--)
MONGOOSE PRO USER GUIDE SHAKER SPEED The shaker is designed to operate at 1,500 rpm (with 50Hz motor) or 1,800 rpm (with 60Hz motor) in both water and oil based mud.
M-I SWACO Green START Button
Red STOP Button
Normal/ Capacity Selector Switch
Motor Control Panels
The motor control panel has a selector switch for Normal (Progressive elliptical) and Capacity (Balanced Elliptical) operation (Refer to Figure 17). Switch between balanced elliptical and progressive elliptical motion to change the motion of the shaker (Refer to Figure 18).
ATTENTION Unit shutdown is NOT necessary when switching between the balanced elliptical and progressive elliptical motions.
Figure 17 Motor Control Panel
EQUIPMENT START-UP
ATTENTION Make sure all objects (such as tools) are clear from equipment BEFORE starting the unit.)
WARNING Keep all guards in place at all times to avoid exposure to parts rotating at high speeds. While power is on, severe injury can occur if hands or feet reach inside the unit.
Ensure screens are properly installed and firmly wedged into place (Refer to Figure 19). Wet screens with base fluid PRIOR to running drilling fluid. Ensure a gate is placed at any unused effluent stream outlet (of the skid), and desired outlet is unobstructed. Check all electrical connections. Turn the selector switch on the control panel to Normal or Capacity mode, depending on the drilling parameters. The “Capacity,” or balanced elliptical mode effectively processes high‐volume solids. The “Normal,” or progressive elliptical mode produces drier cuttings and maximizes drilling fluid recovery. Push START button on control panel to start shaker. Allow fluid to flow over shaker screens.
Figure 18 Operation Selector Switch In Capacity Mode
NOTE: Apply flow of fluid slowly at first to avoid flooding screens.
Keep fluid end point at 75% coverage of the screening surface for optimal performance.
9091120 (--)
Figure 19 Screens & Wedges Firmly In Place
15
M-I SWACO
MONGOOSE PRO USER GUIDE
CONTROLLED SHUTDOWN
Close off flow to feeder. Continue to run unit until drilling fluid already on screens is processed. Thoroughly clean baskets and screens using appropriate base fluid. Push STOP button on the start/stop station.
CAUTION Follow ALL safety instructions. Use proper PPE equipment when using steam or pressure equipment.
NOTE: Do NOT use a squeegee or any other foreign object to clean screens.
NOTE: If unit is out of use for long periods, remove; clean thoroughly; dry; and, either replace in its box or store all screens in a safe, dry area.
SCREEN HANDLING SCREEN INSTALLATION PROCEDURES
Mongoose Pro units have four pretensioned screens and ten wedges per shaker basket (with two spares on the cable tower). Once screens are placed on the screen bed, wedges are driven between each screen edge and support bars on shaker sidewalls. The screen bed is slightly crowned at the center causing screen frames to bow when wedges are forced in place. This prevents screens from “whipping” up and down during shaker operation. Changing / Installing Screens
Stop flow of drilling fluid to shaker. While shaker is running, wash down screens. Clean all cuttings and solids build up around inside of deck and wedges. Shut down shaker.
ATTENTION WARNING Wash down screen area Perform lockout / tag PRIOR to installing new out procedures to shaker screens. isolate unit from the rig power supply. Figure 20 Use Extra Wedges With A Mallet ATTENTION To Loosen Screen Wedges Use a rubber mallet to avoid damage to wedges. Each screen is secured in place by two wedges, one per side. Always remove wedges with a rubber mallet (Refer to Figure 20 for an alternative technique). Strike top handle section of wedges to loosen them.
16
9091120(--)
MONGOOSE PRO USER GUIDE
M-I SWACO
Remove screen panel. Screen panels are removed and installed one at a time. Place the screen wedges in the wedge holders, located on the cable tower, to prevent losing them during screen changes (Refer to Figure 21).
NOTE: Repeat the following steps for each additional screen panel.
Wedges for the second screen from the feed end are REVERSED for easier installation. Wash down screen bed and gasket prior to installing new screens. ATTENTION Replace any deck gaskets that are worn, cracked or hardened. Lay new screen into shaker deck. Position one wedge between screen edge and support bar on shaker side wall (Refer to Figure 23). Position another wedge on the opposite side in same manner and hammer tight (Refer to Figure 22). DO NOT hammer wedges too tightly.
Figure 21 Mongoose Pro Cable Tower With Wedge Holders
ATTENTION
Both wedges must be in PRIOR to position hammering them tight. Failure to do so will prevent the second wedge from being started. Wet down new screens with base fluid PRIOR to use of drilling fluids to properly condition screen mesh. Screen Washing & Blinding
Figure 22 Screen Wedge Secured to Unit
ATTENTION CAUTION Always wash screens all safety Follow PRIOR to storing them to Use all instructions. avoid mechanical damage. recommended PPE when cleaning the shaker. Screens Plugged With Solids Wash screens from back side using base fluid with the screens REMOVED from shaker. Change screens to a finer mesh. Screen Storage
ATTENTION Wash screens with an appropriate medium BEFORE shaker unit is shut down to avoid plugging or binding of the screen meshes by dried solids. NEVER use a wire or stiff fiber brush on the screens.
Store screens in original cardboard packaging to protect screen mesh. Horizontal or vertical stacking is permissible.
9091120 (--)
17
M-I SWACO
MONGOOSE PRO USER GUIDE
SECTION 4.0: PREVENTIVE MAINTENANCE SAFETY RELATED MAINTENANCE PROCEDURES
The following procedures explain basic tasks that will help extend the service life of the Mongoose Pro* shale shaker. M‐I SWACO recommends operators comply with these procedures to ensure the unit operates at its peak efficiency. WARNING Initiate a controlled before shutdown starting ANY parts replacement procedure. Lockout / tag out the unit. Have a certified electrician verify that the power supplies are isolated before performing ANY maintenance on the shaker.
Clean all parts and work area. Block up and secure heavy parts BEFORE working beneath unit or parts. Where heavy lifting is involved, always seek assistance. Remove all screens BEFORE any work is carried out on shaker. Ensure all tools, old parts, nuts, bolts, washers, etc. are removed BEFORE restarting unit after maintenance. Do NOT weld on any part of basket assembly. Use only qualified personnel to perform maintenance. Visually examine unit for signs of wear and/or damage. Repair/replace as necessary. Clean unit removing any solids build‐up. Perform audible checks, investigating as necessary.
MOTOR MAINTENANCE NOTE: Refer to the “Martin Motomagnetic Operator’s Manual” in the Installation, Operation & Maintenance (IOM) manual for detailed maintenance to the vibrator. Installation of vibrator should be done by a certified electrician. Lubricate Motor Bearings (Every 3000 Operational Hours)
ATTENTION Only use Kluber Isoflex Topas NB 52 lubricant for bearings. Failure to do so will void the motor manufacturer warranty.
18
Remove plugs (one for each bearing) and insert an 1/8” NPT Zerk grease fitting (Refer to Figure 23). Pump 1.41 ounces (40 g) of lubricant into each bearing for normal, bearing surface temperatures below 195°F (91°C). Do NOT over grease.
Figure 23 Grease Fittings (Circled)
9091120(--)
MONGOOSE PRO USER GUIDE
M-I SWACO
Motor Bolt Torque Procedure WARNING NEVER reuse the motor installation hardware (bolts, washers and nuts). ALWAYS use new hardware. Retorque new bolts after the first FOUR hours of operating time. NOTE: There are a total of six motor bolts on each motor which are torqued to the proper requirements when shipped from factory.
Figure 24 Motor Bolts – Torque Pattern
Using a 30 mm socket (3/4” drive) with a 200 mm (8”) extension, apply a torque of 435 N‐m (320 ft.‐lb.) to all motor mounting bolts, torquing the bolts in order 1‐6 (Refer to Figure 24). Verify and document motor bolt torque every 672 hours or one time per month of operation for bolts already in use in the field. Motor - Electrical Connections (Isolators)
Any time motor leads are changed or cable is replaced, ensure black neoprene vibration isolators are installed properly BEFORE operating unit.
CAUTION While the isolators are removable, they should always be in place when the unit is in use to protect the electrical connections in the motor. Failure to do so causes premature failure of the wiring and could also cause the mounting posts to break.
Figure 25 Thin Isolator ‐ Motor Leads Showing
Install the thin isolator first (Refer to Figure 25). Connect motor leads to the correct terminals. Place the thick isolator on top of motor leads (Refer to Figure 26). Replace cover and tighten bolts.
Figure 26 Thick Isolator – Motor Leads Not Showing
9091120 (--)
19
M-I SWACO
MONGOOSE PRO USER GUIDE
ISOLATION SPRINGS
NOTE: There are four isolation springs per basket (Refer to Figure 27). Inspection for Fatigue & Replacement
Check each spring for signs of fatigue or fracture every 3 months, or if the shaker basket is tilting side‐to‐side and cuttings are running to one side of the basket.
ATTENTION Springs are covered with a protective black nitrile “boot” serving as a safety precaution against bare springs, which are a potential pinch point (Refer to Figure 27).
Figure 27 Spring Enclosed in Nitrile Boot
Check for spring fatigue by setting basket level and measure the height of each spring. The front two springs should be same height, and the back two springs should be same height. NOTE: Height of back springs may differ from height of front springs. Grease Fitting Replacing Springs
Remove feeder. Lift basket (with proper lifting device) to remove weight from springs. ALWAYS remove weight from springs before attempting to change them. The rear springs require considerable effort to remove. The front springs slide out for replacement.
GREASING DECK ADJUSTMENT JACK
The deck angle adjustment jacks have a grease fitting located on the discharge side of the jack (Refer to Figure 28).
Red Indicator Pointer
Deck Angle Indicator
Once a month, apply 10 shots of multi‐purpose grease into grease fitting (circled in black).
Run deck angle adjustment up and down twice to allow grease penetration to jack inner screw.
20
Figure 28 Grease Fitting
9091120(--)
MONGOOSE PRO USER GUIDE
M-I SWACO
RECOMMENDED PREVENTIVE MAINTENANCE SCHEDULE TABLE 4.1: RECOMMENDED PREVENTIVE MAINTENANCE SCHEDULE Item Task Interval Motors
Grease Motors operating at normal temperature Grease Motors operating above 70 C (158 F) Check for wear and damage. Check for cracks. Check for full up and down travel.
Electrical Cables Screen Gaskets Deck Adjustment System Support Springs Check for uneven compression. Screen Hold Down Check screws for tightness. Bar Gasket Grommets Check for holding. Flow Control Check for free operation. Gates Nuts and Bolts Check for tightness. Motor Bolts Verify proper torque. Deck Adjustment Grease jack fitting. System NOTE: Time intervals above assume continuous shaker running operation.
9091120 (--)
3000 hrs. run time ½ grease every 1500 hrs run time Weekly Monthly Monthly Monthly Monthly Monthly Monthly Monthly Monthly Monthly
21
M-I SWACO
MONGOOSE PRO USER GUIDE
SECTION 5.0: TROUBLESHOOTING Symptom Screen wedge comes loose. Solids are migrating to one side of the basket or not discharging properly.
Shaker makes unusual loud noises.
Bypass stuck. Mud builds up on screen or too much spills over discharge Mud builds up at back edge of screen. Vibrator overheating (70° over ambient temperature.)
TABLE 5.1: TROUBLESHOOTING TABLE Probable Cause
Corrective Action
Wedge not properly installed. Solids under screen or wedge.
Ensure wedge is fully engaged.
Unit not level.
Level unit.
Motor bolts loose. Wedge(s) loose. Vibrator bearings worn. Improper clearance between basket and skid. Loose fasteners or hardware. Caked mud on unit. Incorrect deck angle. Screen mesh too fine. Screen cloth tension loose on screen.
Check motor bolts. Check and reinstall wedges. Replace motor. Determine and fix cause of interference.
Bearing out of grease Bearing worn out.
Locate and tighten. Clean unit. Adjust deck angle. Change to a coarser mesh screen. Replace screen panel. Service bearings. Replace motor.
CAUTION
The following actions MUST be performed by a certified electrician. Check supply to control box. Vibrators fail to rotate. Main supply down. Ensure isolator is ON. Check supply fuses. Damaged wiring. Check wiring. One vibrator fails to rotate. Damaged vibrator. Check vibrator. Damaged thermal overload. Check thermal overload. Shaker stops. Controls tripped. Check circuit breakers and thermal overloads within control panel.
22
9091120(--)
MONGOOSE PRO USER GUIDE
M-I SWACO
SECTION 6.0: MAINTENANCE PROCEDURES SCREEN GASKET REPLACEMENT
ATTENTION WARNING Failure to replace worn or Initiate a controlled hardened screen gaskets shutdown. Disconnect can result in damage to the and lockout/tag out screen bed. the power supply to the control panel. Wash and remove all screens from shaker.
NOTE: Periodic cleaning of shaker keeps the unit running at top efficiency. Wash screens each time shaker is shut down.
Wash deck area thoroughly. Ensure screen bed is clean. Remove hardware and then remove rubber screen gaskets with bars.
NOTE: Replace screen deck rubber screen gaskets when signs of cracking or hardening are present. Grommet Replacement Press down to lock
grommet into place.
NOTE: Replace plastic grommets when rubber screen gasket is replaced (Refer to Figure 29).
Place grommet in the rectangular slot and press down to lock into position. Thoroughly clean screen deck. Lay new screen gasket into place and install screen bar on top of gasket.
NOTE: If necessary, align grommets with screw holes in screen bar using a small screwdriver.
Tighten all screws with a No. 2 Phillips head screwdriver bit. Ensure the lip of the gasket is tight to screen bar.
Figure 29 Plastic Grommet
CAUTION Do NOT over tighten screws. The grommets may pull out of the screen deck if they are subjected to excess torque.
9091120 (--)
23
M-I SWACO
MONGOOSE PRO USER GUIDE
ISOLATION SPRING REPLACEMENT PROCEDURES NOTE: M‐I SWACO recommends replacing the four main basket spring every twelve months. If one spring appears more compressed than the others, replace right away. Remove all weight from springs BEFORE changing them. CAUTION CAUTION Operators may need to Lift the basket (with the proper lifting device) to loosen or remove the feeder box to access feed end remove weight from the
springs.
spring for replacement.
Once basket is lifted, remove top and bottom bolts securing spring spool (Refer to Figure 30). Springs slide out for replacement.
VIBRATOR REMOVAL & INSTALLATION CAUTION WARNING Follow all of the safety Ensure power to the instructions. Use of PPE is control panel is switched OFF and the required during the lockout/tag out procedures installation and removal of are followed. These actions vibratory motors. MUST be performed by a certified electrician. NOTE: Document wire colors to specific terminals in motor junction box BEFORE disconnecting. Disconnecting Cable Gland
Figure 30 Top Spring Bolt
Disconnect terminals from motors. Loosen and slide nut located on cable gland over motor cable (Refer to Figure 31). Loosen cable gland. Carefully pull out all wires in motor junction box, avoiding damage to connectors and wires. When motor cable is removed from junction box, remove all fittings attaching the cable gland to the motor.
Figure 31 Cable Glands (Arrowed) & Lifting Points (Circled)
24
9091120(--)
MONGOOSE PRO USER GUIDE
M-I SWACO
Lifting & Moving Vibrators
WARNING Ensure power to the control panel is switched OFF and the lockout / tag out procedures are followed. Only a qualified electrician can perform connection and disassembly procedures with this unit.
ATTENTION Lifting lugs on the vibratory motors are designed to lift the motor, NOT the Mongoose Pro. Do NOT, under any circumstances, attempt to lift the unit or basket assembly by the vibratory motor lifting lugs.
CAUTION Motors are heavy. Each motor weighs 293 lb (133 kg). Apply a small amount of tension to the lifting device to keep the motors from falling during motor bolt removal.
Hook proper lifting device to motor lifting points. Remove motor bolts and hardware.
NOTE: Note motor wire inlet location and direction on junction box BEFORE removing motor.
Remove motor. Installing/Replacing Motor
ATTENTION ATTENTION ATTENTION CAUTION Note the orientation of NEVER dent, strike, mar, or Do NOT run shakers installing a BEFORE motor bolts. The head of grind ANYTHING against with one or more vibratory motor, ensure the each bolt is on the INSIDE the motor mounting surface motor mounting vibratory motor mounting of the motor plate. The nut or the motor plate. Damage bolts missing or improperly area is absolutely clean and is on the OUTSIDE of the to either will render the torqued. Failure to follow undamaged. motor plate. equipment inoperable. these guidelines can result NEVER reuse motor in motor malfunction, installation hardware. causing extensive damage Always use new bolts. Clean bottom of vibrator feet. or injury. Check and retorque new Ensure motor plate is also clean. bolts after the first four Lift vibrator in place using proper lifting equipment. hours of operation time. Align motor wire inlet location in the same spot as before. Install new motor mounting hardware. Hand‐tighten all bolts. Apply initial torque of 160 ft./lbs. (217 Nm) to all motor bolts. Apply a final torque of 320 ft./lbs. (434 Nm) to all motor bolts. Reinstall all fittings into the motor wire inlet in the same order as they were removed. Feed wires into fittings. Ensure wires are not damaged or twisted inside the elbow. Connect electric cable to vibrator using appropriate glands. Tighten nut, then cord grip onto cable gland. Reconnect wires to correct terminals. Reinstall junction box cover and tighten bolts. Retorque motor mounting bolts after running motors for 4 hours. If the vibrator has adjustable eccentric weights, fix counter‐weights at a setting of 100%. Recheck motor rotation.
NOTE: Top motors (one piece weights) are fixed at 100%. Verify bottom swing motors are set at 100%.
9091120 (--)
25
M-I SWACO
MONGOOSE PRO USER GUIDE
ELEVATOR JACK REPLACEMENT
CAUTION WARNING Use proper lifting guidelines. Initiate a controlled shutdown before starting ANY parts replacement procedure or general maintenance. Lockout / tag out the unit. Figure 32 Overhead View of Hardware Raise basket enough to relieve weight off of spring and remove spring. Base Loosen and remove 12 mm hardware at base of elevator jack with a 19 mm wrench or socket with extensions (Refer to Figure 32). Remove spring support bracket and pointer from elevator jack. Note the position of the 3/8” thick steel spacer underneath each jack’s hardware base. Reinstall spring support and pointer on new elevator jack in the same previous position. Mount new elevator jack on indicator plate. Install 12 mm hardware and hand tighten. Ensure pointer does not interfere with indicator plate when jack elevates. A one quarter‐inch (1/4”) gap is preferred. Inspect and reinstall spring. When spring is lowered back in position, make sure the urethane spring spool is in place.
SHAKER WASH DOWN PROCEDURES
CAUTION Follow all safety instructions. Use of PPE is required during shaker wash down procedures. Normal Daily Wash Down Procedures
Use base fluid and thoroughly hose down entire unit with screens in place and shaker running to completely remove all solids from screen surface. When unit is clean, shut off power and remove all screens and set them aside. Continue washing shaker. Clean screen bed area extremely well ensuring seal area is free of drilling fluid that can cause bypass around screen frame later. Wash screens to remove sticky solids.
NOTE: When cleaning with a pressure washer, keep the nozzle an adequate distance from the screens to prevent tearing the mesh.
26
9091120(--)
MONGOOSE PRO USER GUIDE
M-I SWACO
Wash Down After Circulation of Completion Fluids
CAUTION Completion fluids typically contain a higher amount of chlorides and are usually highly corrosive. Therefore, it is extremely important to carry out an extensive wash down after circulation of completion fluids is finished.
Follow the “Normal Daily Wash Down” procedures listed previously. Lift the shaker basket to its highest uphill angle and thoroughly wash interior of basket.
NOTE: There should be no screens in the basket
Wash screens separately.
9091120 (--)
27
M-I SWACO
MONGOOSE PRO USER GUIDE
THIS PAGE INTENTIONALLY LEFT BLANK
28
9091120(--)
MONGOOSE PRO USER GUIDE
M-I SWACO
SECTION 7.0: RIG CRITICAL SPARE PARTS LIST (RSPL)
RIG CRITICAL SPARE PARTS LIST
9091120 (--)
29
M-I SWACO
MONGOOSE PRO USER GUIDE
Figure 33 Mongoose Pro Assembly
30
9091120(--)
MONGOOSE PRO USER GUIDE
M-I SWACO
TABLE 7.1: RIG CRITICAL SPARE PARTS LIST FOR MONGOOSE PRO Item Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Part Number 6912525 6905525 6920525 05‐ 244 9360007 1345015 04‐1704 1305055 BM6K80290 5837001 5895001 07‐415 1441471 7150018 7152032 7790017 7790019 7790018 7150063 8265105 7150016 7150015 7510037 7510038
9091120 (--)
Description MOTOR 2.5 HP 220‐240/440‐480V, FIXED WEIGHT 60/3/1800 70 FRAME MOTOR 2.5 HP 220‐240/380‐415V, FIXED WEIGHT 50/3/1500 70 FRAME MOTOR 2.5 HP 575‐600V, FIXED WEIGHT 60/3/1800 70 FRAME LOCK WASHER SCHNORR M20 MARTIN #513014 SPRING COIL 7” WASHER FLAT BLACKENED F436 ¾” X 1‐15/32 OD HARDENED SCREW HEX HEAD PLATED M20‐1.5 X 120 MM LG GRADE 10.9 NUT HEX PLATED M20 X 1.5, 35mm GRD 10.9 BLACK TRICHROMATE PLTD SPRING SPOOL GASKET, MONGOOSE FLAT PANEL SCREEN WEDGE, MONGOOSE SCREEN CLAMPING GROMMET SCREW .273 SQUARE PANEL HOLE #8 FLAT HEAD SHEET METAL SCREW WITH SQUARE DRIVE CONTACTOR, REVERSING RELAY, THERMAL OVERLOAD (5.5‐7.5) TRANSFORMER 460V TRANSFORMER 575V TRANSFORMER 380V POWER DISTRIBUTION BLOCK EMITTER PLASTIC VCI‐105 RELAY BASE RELAY, DPDT 10A 120VAC CIRCUIT BREAKER, 2 POLE, 1A CIRCUIT BREAKER, 1 POLE, 3A
Qty. 1 6 4 12 6 6 8 4 8 56 56 1 2 1 1 1 1 1 1 1
31
M-I SWACO
MONGOOSE PRO USER GUIDE
Figure 34 Mongoose Pro Dual Unit
32
9091120(--)
MONGOOSE PRO USER GUIDE
M-I SWACO
TABLE 7.2: RIG CRITICAL RECOMMENDED SPARE PARTS LIST FOR DUAL SHAKERS* Item Number
Part Number
Description
6912525 MOTOR 2.5 HP 220‐240/440‐480V, FIXED WEIGHT 60/3/1800 70 FRAME 6905525 MOTOR 2.5 HP 220‐240/380‐415V, FIXED WEIGHT 50/3/1500 70 FRAME 6920525 MOTOR 2.5 HP 575‐600V, FIXED WEIGHT 60/3/1800 70 FRAME 2 05‐ 244 LOCK WASHER SCHNORR M20 MARTIN #513014 3 9360007 SPRING COIL 7” 4 1345015 WASHER FLAT BLACKENED F436 ¾” X 1‐15/32 OD HARDENED 5 04‐1704 SCREW HEX HEAD PLATED M20‐1.5 X 120 MM LG GRADE 10.9 6 1305055 NUT HEX PLATED M20 X 1.5, 35mm GRD 10.9 BLACK TRICHROMATE PLTD 7 BM6K80290 SPRING SPOOL 8 5837001 GASKET, MONGOOSE FLAT PANEL SCREEN 9 5895001 WEDGE, MONGOOSE SCREEN CLAMPING 10 07‐415 GROMMET SCREW .273 SQUARE PANEL HOLE 11 1441471 #8 FLAT HEAD SHEET METAL SCREW WITH SQUARE DRIVE 12 7150018 CONTACTOR, REVERSING 13 7152032 RELAY, THERMAL OVERLOAD (5.5‐7.5) 7790017 TRANSFORMER 460V 14 7790019 TRANSFORMER 575V 7790018 TRANSFORMER 380V 15 7150063 POWER DISTRIBUTION BLOCK 16 8265105 EMITTER PLASTIC VCI‐105 17 7150016 RELAY BASE 18 7150015 RELAY, DPDT 10A 120VAC 19 7510037 CIRCUIT BREAKER, 2 POLE, 1A 20 7510038 CIRCUIT BREAKER, 1 POLE, 3A 21 3914037 GASKET, FEEDER BOX COMMON POSSUM BELLY 22 3914036 GASKET, POSSUM BELLY TRANSITION DUAL SHAKER 23 06‐247 ROLL PIN ¼ DIAMETER X 1.50 LG *Refer to Figure 33 for Spare Parts 1-20 1
Qty.
1 6 4 12 6 6 8 4 8 56 56 1 2 1 1 1 1 1 1 1 2 1 1
9091120 (--)
33
M-I SWACO
MONGOOSE PRO USER GUIDE
Figure 35 Mongoose Pro Triple Unit
34
9091120(--)
MONGOOSE PRO USER GUIDE
M-I SWACO
TABLE 7.3: RIG CRITICAL RECOMMENDED SPARE PARTS LIST FOR TRIPLE SHAKERS* Item Number
Part Number 6912525 6905525 6920525 05‐ 244 9360007 1345015 04‐1704 1305055
Description
MOTOR 2.5 HP 220‐240/440‐480V, FIXED WEIGHT 60/3/1800 70 FRAME 1 MOTOR 2.5 HP 220‐240/380‐415V, FIXED WEIGHT 50/3/1500 70 FRAME MOTOR 2.5 HP 575‐600V, FIXED WEIGHT 60/3/1800 70 FRAME 2 LOCK WASHER SCHNORR M20 MARTIN #513014 3 SPRING COIL 7” 4 WASHER FLAT BLACKENED F436 ¾” X 1‐15/32 OD HARDENED 5 SCREW HEX HEAD PLATED M20‐1.5 X 120 MM LG GRADE 10.9 NUT HEX PLATED M20 X 1.5, 35mm GRD 10.9 BLACK TRICHROMATE 6 PLTD 7 BM6K80290 SPRING SPOOL 8 5837001 GASKET, MONGOOSE FLAT PANEL SCREEN 9 5895001 WEDGE, MONGOOSE SCREEN CLAMPING 10 07‐415 GROMMET SCREW .273 SQUARE PANEL HOLE 11 1441471 #8 FLAT HEAD SHEET METAL SCREW WITH SQUARE DRIVE 12 7150018 CONTACTOR, REVERSING 13 7152032 RELAY, THERMAL OVERLOAD (5.5‐7.5) 7790017 TRANSFORMER 460V 14 7790019 TRANSFORMER 575V 7790018 TRANSFORMER 380V 15 7150063 POWER DISTRIBUTION BLOCK 16 8265105 EMITTER PLASTIC VCI‐105 17 7150016 RELAY BASE 18 7150015 RELAY, DPDT 10A 120VAC 19 7510037 CIRCUIT BREAKER, 2 POLE, 1A 20 7510038 CIRCUIT BREAKER, 1 POLE, 3A 21 06‐247 ROLL PIN ¼ DIAMETER X 1.50 LG 22 04‐1509 HHCS M12 X 70 MM LG WITH FULL THREADS 23 3916067 GASKET, FULL FACE ANSI FLANGE, 150 LBS., 10” 24 1493003 HHCS M24‐3.0 X 90 MM, BLACK TRICHROMATE PLATED 25 03‐412 HEX NUT M24 26 3914035 GASKET, TRANSITION BYPASS POSSUM BELLY 27 3914037 GASKET, FEEDER BOX COMMON POSSUM BELLY *Refer to Figure 33 for Spare Parts 1-20
Qty. 2 12 8 24 12 12 16 8 16 112 112 2 4 2 2 2 2 2 2 2 1 10 1 12 12 1 3
9091120 (--)
35
M-I SWACO
MONGOOSE PRO USER GUIDE
Figure 36 Mongoose Pro Quad Unit
36
9091120(--)
MONGOOSE PRO USER GUIDE
M-I SWACO
TABLE 7.4: RIG CRITICAL RECOMMENDED SPARE PARTS LIST FOR QUAD SHAKERS* Item Number
Part Number 6912525 6905525 6920525 05‐ 244 9360007 1345015 04‐1704 1305055 BM6K80290 5837001 5895001 07‐415 1441471 7150018 7152032 7790017 7790019 7790018 7150063 8265105 7150016 7150015 7510037 7510038 05‐294 04‐1684 05‐244 03‐435 3916067 5647011
Description
MOTOR 2.5 HP 220‐240/440‐480V, FIXED WEIGHT 60/3/1800 70 FRAME MOTOR 2.5 HP 220‐240/380‐415V, FIXED WEIGHT 50/3/1500 70 FRAME MOTOR 2.5 HP 575‐600V, FIXED WEIGHT 60/3/1800 70 FRAME 2 LOCK WASHER SCHNORR M20 MARTIN #513014 3 SPRING COIL 7” 4 WASHER FLAT BLACKENED F436 ¾” X 1‐15/32 OD HARDENED 5 SCREW HEX HEAD PLATED M20‐1.5 X 120 MM LG GRADE 10.9 6 NUT HEX PLATED M20 X 1.5, 35mm GRD 10.9 BLACK TRICHROMATE PLTD 7 SPRING SPOOL 8 GASKET, MONGOOSE FLAT PANEL SCREEN 9 WEDGE, MONGOOSE SCREEN CLAMPING 10 GROMMET SCREW .273 SQUARE PANEL HOLE 11 #8 FLAT HEAD SHEET METAL SCREW WITH SQUARE DRIVE 12 CONTACTOR, REVERSING 13 RELAY, THERMAL OVERLOAD (5.5‐7.5) TRANSFORMER 460V 14 TRANSFORMER 575V TRANSFORMER 380V 15 POWER DISTRIBUTION BLOCK 16 EMITTER PLASTIC VCI‐105 17 RELAY BASE 18 RELAY, DPDT 10A 120VAC 19 CIRCUIT BREAKER, 2 POLE, 1A 20 CIRCUIT BREAKER, 1 POLE, 3A 21 FLAT WASHER M20 22 HHCS M20‐2.5 X 90 MM LG, GRADE 10.9, BLACK TRICHROMATE PLATED 23 LOCK WASHER SCHNORR M20 MARTIN #513014 24 HEX NUT M20‐2.5 BLACK TRICHROMATE PLATED 25 GASKET, FULL FACE ANSI FLANGE 150 LBS., 10” VALVE, BUTTERFLY 12” WAFER BODY WITH HANDLE & 10 POSITION 26 THROTTLE PLATE 5644042 VALVE, BUTTERFLY 10” WAFER BODY WITH HANDLE & 10 POSITION 27 THROTTLE PLATE 28 05‐308 FLAT WASHER M24 REGULAR 29 1493001 SCREW HEX HEAD, GRADE 8.8, BLACK TRICHROMATE PLATED 30 05‐309 SPLIT LOCK WASHER M24 31 03‐412 HEX NUT M24 1493002 SCREW HEAD M24‐3.0 X 180 MM, GRADE 8.8, BLACK TRICHROMATE 32 PLATED 33 1493003 HHCS M24‐3.0 X 90 MM, BLACK TRICHROMATE PLATED *Refer to Figure 33 for Spare Parts 1-20 1
Qty. 2 12 8 24 12 12 16 8 16 112 112 2 4 2 2 2 2 2 2 2 152 76 76 76 3 2 4 216 12 108 108 72 24
9091120 (--)
37
M-I SWACO
MONGOOSE PRO USER GUIDE
SECTION 8.0: ELECTRICAL SCHEMATICS
ELECTRICAL SCHEMATICS
38
9091120(--)
MONGOOSE PRO USER GUIDE
M-I SWACO
WIRING SCHEMATIC – 2 MOTOR/UL
380-415V
9091120 (--)
39
M-I SWACO
MONGOOSE PRO USER GUIDE
WIRING SCHEMATIC – 2 MOTOR/ATEX
40
440-480V
9091120(--)
MONGOOSE PRO USER GUIDE
M-I SWACO
550 – 600V
9091120 (--)
WIRING SCHEMATIC – 2 MOTOR
41
THISPAGEINTENTIONALLYLEFTBLANKȱ
THIS PAGE INTENTIONALLY LEFT BLANK
Worldwide Headquarters P.O. Box 42842 Houston, TX 77242‐2842 Tel: 281‐561‐1300 Fax: 281‐561‐1441 www.miswaco.com E‐mail:
[email protected]
