Technical reference guide Boiler steriliser.pdf

TECHNICAL REFERENCE GUIDE

APPLICATION GUIDE Volume 8 Trade applications

Boiler house applications

Volume 1

Pressure control applications

Volume 2

Temperature control applications

Volume 3

Metering applications

Volume 4

Trapping applications

Volume 5

Condensate recovery applications

Volume 6

Clean steam applications

Volume 7

Trade applications

Volume 8

The application drawings shown in this publication are intended as a guide only. As different countries and local areas use different standards, certain items on some drawings may require revision, e.g. Safety valves - all flanged safety valves are shown as SV5 type with open bonnets. This may suit the preferences of many countries, however, some areas may prefer to use safety valves with closed bonnets. Please note the SV5 is also available in closed bonnet versions. Selection of products subject to maximum pressure and temperature ratings. In the interests of development and improvement of products, we reserve the right to change the specification.

Please contact your local Spirax Sarco engineer with details of specific applications. © Copyright 1998

2

Volume 8

Trade applications

Paper industry: Multi-cylinder blow through system - condensate removal

4

Paper industry: Drying cylinder blow through differential pressure control

5

Paper industry: Steam shower control

6

Corrugating industry: Hot plate control

7

Moulding: Multi-platen press

8

Moulding: Tyre mould (flanged)

9

Moulding: Tyre mould (screwed)

10

Laundry: Garment presses

11

Laundry: Trapping and venting of flatwork ironer

12

Brewing industry: Brewery heater

13

Brewing industry: Hot liquor tank control

14

Brewing industry: Calandria control

15

Brewing industry: Fermentation control

16

Hospitals: Instrument sterilizer

17

Hospitals: Autoclave - Filtered steam supply

18

Hospitals: Heating cabinet temperature control

19

Textile industry: Canopy drier flash recovery

20

HVAC: Air heater batteries - multi-unit installation

21

Food industry: Jacketed pan assembly

22

Dairy industry: Pasteuriser control

23

Selection of products subject to maximum pressure and temperature ratings. In the interests of development and improvement of products, we reserve the right to change the specification.

© Copyright 1998

3

Paper Industry: Multi-Cylinder Blow Through System - Condensate Removal Vac 17

2

Air supply

3 High pressure steam supply

18

1

4 To vacuum condenser, thermocompressor or low pressure steam system Paper

Paper Steam to pump 5

6 Condensate

Condensate receiver

Blow through steam / condensate mixture

7

8 910

SPIRAX SARCO

11

12 13 14 1516

Table of parts Part No. 1 2 3 4 5 6 10 7, 16 12, 15 13 14 9 8 11

Description STRAINER (flanged) ACTUATOR POSITIONER CONTROL VALVE PRESSURE GAUGE AIR VENT LIFT CHECK VALVE BALL VALVE DISC CHECK VALVE AUTOMATIC PUMP FLOAT TRAP THERMODYNAMIC TRAP SPIRATEC SENSOR CHAMBER STRAINER (flanged)

Bronze Fig 3

Cast iron SG iron Steel Stainless steel Fig 33 Fig 37SG Fig 34 Fig 36 Spirax Sarco PN5000 series actuator EP5 electropneumatic positioner KE73 KE43 KE63 100 mm diameter Spirax Sarco pressure gauge with 'U' or ring syphon AV13 AV21 LCV1 LCV2 M10 or M20 M10 or M20 DCV2, 3 or 4 MFP14 automatic pump FT43 FT14 FT44 TD42 ST17 ST14 ST16 Fig 3 Fig 37 Fig 34 Fig 36

Selection of products subject to maximum pressure and temperature ratings. In the interests of development and improvement of products, we reserve the right to change the specification.

4

© Copyright 1998

Paper Industry: Drying Cylinder Blow Through Differential Pressure Control Note: Air supply to control valve not shown.

High pressure steam supply

1

2 3 4 5

To flash vessel Differential pressure controller 6 7 Paper

9

8

Low pressure steam 10

11 Blow through steam / condensate mixture

12 13 14 15 16 17 Condensate

Table of parts Part No. 1, 5, 12, 17 2, 14 3 4, 16 6 7 8 9 10 11 15 13

Description Globe type ISOLATING Piston type VALVE Ball type SPIRATEC SENSOR CHAMBER THERMODYNAMIC TRAP LIFT CHECK VALVE ACTUATOR POSITIONER CONTROL VALVE SAFETY VALVE PRESSURE GAUGE FLASH VESSEL FLOAT TRAP STRAINER

Bronze HV3

Cast iron

SG iron

Steel Stainless steel A3S RP31 M10 M10 ST171 ST141 ST161 TD42 LCV1 LCV2 Spirax Sarco PN5000 series pneumatic actuator Spirax Sarco EP5 electropneumatic positioner KE73 KE43 KE63 SV57 SV3 or SV54 100 mm diameter Spirax Sarco pressure gauge with 'U' or ring syphon Spirax Sarco FV type flash vessel FT14 FT16 Fig 1 or 12 Fig 12SG Fig 14 Fig 16

Selection of products subject to maximum pressure and temperature ratings. In the interests of development and improvement of products, we reserve the right to change the specification.

© Copyright 1998

5

Paper Industry: Steam Shower Control

1

2

3

Steam

4

5

6

7

8

9

Condensate

10

11

Condensate

Table of parts Part No. 1, 4, 9 2 3 5 6 7 8, 10 11

Description BALL VALVE SEPARATOR PNEUMATICALLY ACTUATED BALL VALVE LIFT CHECK VALVE FLOAT TRAP SPIRATEC SENSOR CHAMBER STRAINER BALANCED PRESSURE TRAP

Spirax Sarco reference: M10 ball valve Type S1, S2, S5 or S6 separator BVA pneumatically actuated rotary M10 ball valve LCV1 or LCV2 lift check valve FT14 float trap ST171 sensor chamber Fig 12 SG 'Y' type strainer MST21 steam trap

Selection of products subject to maximum pressure and temperature ratings. In the interests of development and improvement of products, we reserve the right to change the specification.

6

© Copyright 1998

Corrugating Industry: Hot Plate Control Note: Air supply to control valve not shown. 1

2

3

4

6

7

Flash steam supply 8

9

10

Live steam supply

5

Backers

17

3rd bed

2nd bed

1st bed 17

11

17

12 13

17

14

15 16

11

17

12 13

17

14

15 16

11

12 13

14

Condensate to vented 15 16 receiver and pump

Table of parts Part No. 1, 10 2 3 4 5 6 7 8 9 11, 16, 17 12 13 14 15

Description BELLOWS SEALED VALVE STRAINER (flanged) ACTUATOR POSITIONER CONTROL VALVE SAFETY VALVE CONTROLLER PRESSURE GAUGE PRESSURE TRANSMITTER BALL VALVE (screwed) STRAINER (screwed) SPIRATEC SENSOR CHAMBER FLOAT TRAP LIFT CHECK VALVE

Bronze

Cast iron SG iron Steel Stainless steel BSA1 BSA2 BSA3 Fig 3 Fig 33 Fig 37SG Fig 34 Fig 36 PN5000 series pneumatic actuator EP5 electropneumatic positioner KE73 KE43 KE63 SV57 SV3 or SV54 ELSX70 controller 100 mm diameter pressure gauge with 'U' or ring syphon EL2600 pressure transmitter with 'U' syphon assembly M10 M10 Fig 1 or 12 Fig 12SG Fig 14 Fig 16 ST171 ST141 ST161 FT14 FT16 LCV1 LCV2

Selection of products subject to maximum pressure and temperature ratings. In the interests of development and improvement of products, we reserve the right to change the specification.

© Copyright 1998

7

Moulding: Multi-Platen Press

On - off electrical supply

1

2

4 3

5

6

7

8

DP17T

Steam 15 16

Condensate 9

10 11

12 13 14

17 18 19 20 21

15 16

Condensate

Table of parts Part No. 1 2, 8 3 4, 7 5 6 9, 14, 17 10, 21 11, 20 12 13, 16, 18 15 19

Description SEPARATOR BELLOWS SEALED STOP VALVE STRAINER (flanged) PRESSURE GAUGE PRESURE REDUCING VALVE SAFETY VALVE ISOLATING Globe type VALVE Piston type (screwed) Ball valve STRAINER (screwed) SPIRATEC SENSOR CHAMBER FLOAT TRAP LIFT CHECK VALVE SWIVEL CONNECTOR THERMODYNAMIC TRAP THERMODYNAMIC TRAP

Bronze

Cast iron SG iron Steel Stainless steel S3 1808 or S5 1808 or S6 BSA1 BSA2 BSA3 Fig 3 Fig 33 Fig 37SG Fig 34 Fig 36 100 mm diameter Spirax Sarco pressure gauge with 'U' or ring syphon pipe DP17E SV57 SV3 or SV 54 HV3 A3S RP31 M10 M10 Fig 1 or 12 Fig 12SG Fig 14 Fig 16 ST171 ST141 ST161 FT14 FT16 LCV1 LCV2

Selection of products subject to maximum pressure and temperature ratings. In the interests of development and improvement of products, we reserve the right to change the specification.

8

UTD30L or LA TD42 or TD52

© Copyright 1998

Moulding: Tyre Mould (Flanged) Note: Steam pressure controlled upstream by DP17 to provide uniform temperature in mould.

1

Steam Flexible hoses 2

3

4

2

5

3

6

4

7

5

6

7

Condensate

Table of parts Part No.

Description

3

Bellows sealed type ISOLATING Butterfly type VALVE Ball type DISC CHECK VALVE

4

THERMODYNAMIC TRAP

5 6

SPIRATEC SENSOR CHAMBER STRAINER

1, 2, 7

Bronze

Cast iron BSA1

SG iron BSA2 BS7

Steel BSA3

Stainless steel

M20

M20 DCV2, 3 or 4 TD24F TD45 TD1464 ST163 Fig 36

TD62 TD120

Fig 3

Fig 33

Fig 37SG

Selection of products subject to maximum pressure and temperature ratings. In the interests of development and improvement of products, we reserve the right to change the specification.

ST143 Fig 34

© Copyright 1998

9

Moulding: Tyre Mould (Screwed) Note: Steam pressure controlled upstream by DP17 to provide uniform temperature in mould.

1

Steam

2

3

4

2

5

3

6

4

5

6

Condensate

Table of parts Part No. 1, 2, 6 3 4 5

Description Globe type ISOLATING Piston type VALVE Ball type LIFT CHECK VALVE THERMODYNAMIC TRAP STRAINER

Bronze HV3

Cast iron

SG iron

LCV1 Fig 1 or 12

Fig 12SG

Selection of products subject to maximum pressure and temperature ratings. In the interests of development and improvement of products, we reserve the right to change the specification.

10

Steel A3S RP31 M10 LCV2 Fig 14

Stainless steel

M10 TD42 or TD52 Fig 16

© Copyright 1998

Laundry: Garment Presses

Steam supply

1

2

3 6

8

9

7

4

5

10 11

12 13

14

15

Condensate return line

Table of parts Part No. 1, 2, 5 7, 11, 12 4, 8, 15 3, 9, 14 6, 10, 13

Description Globe type ISOLATING Piston type VALVE Ball type SPIRATEC SENSOR CHAMBER SWIVEL CONNECTOR THERMODYNAMIC TRAP LIFT CHECK VALVE

Bronze HV3

Cast iron

SG iron

ST171

LCV1

Selection of products subject to maximum pressure and temperature ratings. In the interests of development and improvement of products, we reserve the right to change the specification.

Steel A3S RP31 M10 ST141

Stainless steel

M10 ST161 UTD30L or UTD30LA

LCV2

© Copyright 1998

11

Laundry: Trapping and Venting of Flatwork Ironer Note: Steam supplies not shown but would enter at opposite end of beds. 1

Air vents - drain to a safe place

Rollers

Steam beds

2

Condensate

3

4

5

6

Table of parts Part No. 1 2, 6 3 4 5

Description AIR VENT Globe type ISOLATING Piston type VALVE Ball type SIGHT CHECK FLOAT TRAP STRAINER

Bronze AV13 HV3

Cast iron

SG iron

Stainless steel

M10

Sight check Fig 1 or 12

FT14C Fig 12SG

Selection of products subject to maximum pressure and temperature ratings. In the interests of development and improvement of products, we reserve the right to change the specification.

12

Steel AV21 A3S RP31 M10

Fig 14

FT16C Fig 16

© Copyright 1998

Brewing Industry: Brewery Heater

1

2

3

4

5

5 Steam in

19

10

6

7

8

9

12 11 13

14

15

16

17 Condensate

18

20

21

22

Condensate

Table of parts Part No. 1 2 3 5, 11 6, 14, 18 7, 15, 20 13 4, 9, 10, 12,17, 22 8, 16, 21 19

Description SEPARATOR ISOLATING VALVE STRAINER (flanged) STRAINER (screwed) SPIRATEC SENSOR CHAMBER FLOAT TRAP ANGLE TYPE STRAINER ISOLATING VALVE (screwed) LIFT CHECK VALVE AIR VENT

Bronze

Fig 3 Fig 1 or 12

Cast iron S3 BSA1 Fig 33

SG iron BSA2 Fig 37SG Fig 12SG ST171 FT14

Fig 4, 5 or 6 HV3 LCV1 AV13

Selection of products subject to maximum pressure and temperature ratings. In the interests of development and improvement of products, we reserve the right to change the specification.

Steel 1808 or S5 BSA3 Fig 34 Fig 14 ST141

Stainless steel 1808 or S6 Fig 36 Fig 16 ST161

LCV2 AV21

© Copyright 1998

13

Brewing Industry: Hot Liquor Tank Control Note: Tank outlet not shown.

1

2

3 4

Steam in

5

6

7

8

9

10

11

12

DP17

Pump

13

14 15 16 17

18

19

Steam coil Hot liquor tank 25

Water supply to tank

Condensate 20

21 22 23 24

Table of parts Part No. 1 2, 8 3 4, 7 5 6 9 10 13, 18, 20, 25 14, 24 15, 23 16, 22 17, 21 19 11 12

Description SEPARATOR ISOLATING VALVE (flanged) STRAINER (flanged) PRESSURE GAUGE PRESSURE REDUCING VALVE SAFETY VALVE CONTROL VALVE VACUUM BREAKER ISOLATING Globe type VALVE Piston type (screwed) Ball type STRAINER (screwed) SPIRATEC SENSOR CHAMBER FLOAT TRAP LIFT CHECK VALVE SELF-ACTING CONTROL LEVEL PROBE LEVEL CONTROLLER

Bronze

Cast iron SG iron Steel Stainless steel S3 1808 or S5 1808 or S6 BSA1 BSA2 BSA3 / M20 Fig 3 Fig 33 Fig 37 Fig 34 or Fig1738 Fig 36 100 mm diameter pressure gauge with 'U' or ring syphon tube DP17 DP143 SV3 or SV57 SV54 KA33 KA33 or KB33 KA, KB or KC43 VB14 VB21 HV3 A3S RP31 M10 M10 Fig 1 or 12 Fig 13 Fig 12SG Fig 14 Fig 16 ST171 ST141 ST161 FT14 LCV1 LCV2 Type 121, 122, 123 or 128 self-acting control LP10 - 3 LC1000

Selection of products subject to maximum pressure and temperature ratings. In the interests of development and improvement of products, we reserve the right to change the specification.

14

© Copyright 1998

Brewing Industry: Calandria Control Note: Air supply to control valve not shown. 1

2

PLC PLC

3

5

6

8

4

Steam in

Brewing 'copper'

23

7

9 External calandria 10 Wort back to copper 11

12 13

14

15

16

17 18

19

20

21

22

Table of parts Part No. 1 9 10 5 6 2, 17, 22 8 4 18, 23 7 3, 21 13, 20 14, 19 11, 16 12 15

Description SEPARATOR PRESSURE TRANSMITTER DISPLAY UNIT PNEUMATIC ACTUATOR POSITIONER ISOLATING Bellows sealed type VALVE Butterfly type (flanged) Ball type VACUUM BREAKER FLOWMETER DISC CHECK VALVE CONTROL VALVE STRAINER (flanged) SPIRATEC SENSOR CHAMBER FLOAT TRAP ISOLATING VALVE (screwed) STRAINER (screwed) LIFT CHECK VALVE

Bronze

Cast iron SG iron Steel S3 1808 or S5 M610 differential pressure transmitter assembly M700 display unit PN5000 series pneumatic actuator EP5 electropneumatic actuator BSA1 BSA2 BSA3 BS7 M20

VB14

Stainless steel 1808 or S6

M20 VB21

Spirax Sarco 'Gilflo ILVA' pipeline flowmeter

Fig 3

Fig 33

KE73 Fig 37SG FT14

HV3 Fig 12 LCV1

Fig 12SG

Selection of products subject to maximum pressure and temperature ratings. In the interests of development and improvement of products, we reserve the right to change the specification.

KE43 Fig 34 ST141 FT44 Fig 14 LCV2

DCV2, 3 or 4 KE63 Fig 37 ST161 FT46 Fig 16

© Copyright 1998

15

Brewing Industry: Fermentation Control Note: Air supply to control valve not shown.

1

2

3

4

EL T

VAT

Cooling water out Cooling jacket

6

Cooling water in

7

5

Purge line

Table of parts Part No. 1 2 3 4 5 6 7

Description TEMPERATURE SENSOR CONTROLLER ACTUATOR POSITIONER CONTROL VALVE DISPLAY UNIT FLOWMETER

Spirax Sarco reference: EL2000 series Pt100 sensor ELSX65 controller PN5000 series pneumatic actuator EP5 electropneumatic positioner KE43, KE63 or KE73 control valve M700 display unit VFM2000 vortex flowmeter

Selection of products subject to maximum pressure and temperature ratings. In the interests of development and improvement of products, we reserve the right to change the specification.

16

© Copyright 1998

Hospitals: Instrument Sterilizer

1

2

3

4

5

6

7

DP17

Steam in

9

10

11

12

13

14

15 Chamber air vent

Jacket air vent

8

Sterilizer

Condensate

20

16

17

21

22 23 Condensate

18 19 Condensate

Table of parts Part No. 1 2, 7, 8, 13, 16, 20 3, 12 4 5 6 9, 19, 23 10 11, 17, 21 14, 15 18, 22 * With near to

Description SEPARATOR Globe type ISOLATING Piston type VALVE Ball type STRAINER PRESSURE REDUCING VALVE PRESSURE GAUGE SAFETY VALVE CHECK VALVE FLOAT TRAP SPIRATEC SENSOR CHAMBER AIR VENT BALANCED PRESSURE THERMOSTATIC STEAM TRAP steam capsules

Bronze

Cast iron S2

SG iron S1

HV3

Steel S5 A3S RP31 M10 Fig 14

Stainless steel S6

M10 Fig 12SG Fig 16 DP17 100 mm diameter Spirax Sarco pressure gauge with 'U' or ring syphon pipe SV3 SV3 LCV1 LCV2 FT14 FT44 FT16 ST171 ST141 ST161 AV13 AV21 BPT21Y* or BPT30Y*

Fig 1 or 12

Fig 13

Selection of products subject to maximum pressure and temperature ratings. In the interests of development and improvement of products, we reserve the right to change the specification.

© Copyright 1998

17

Hospitals: Autoclave - Filtered Steam Supply 1

Note: Electrical supply to DP17E solenoid valve not shown.

2

3

4

5

6

7

8

9

DP17TE

Steam in Steam to jacket Jacketed air vent 17 Condensate

11 12 13

14 15

10

Chamber air vent 18

16

Condensate to drain via air break Autoclave

Jacket trap set

19 20 21 22

23

Filtered steam to chamber

Chamber trap set

Condensate to drain

24 25 26 27 28

29 30

31

32 33

34

Table of parts Part No. 1 2, 9 3 4, 7 5 6 8 10 11, 16, 19, 23, 24, 28, 29, 34 12, 20, 25, 30 13, 26, 31 14, 22, 27, 32 15, 33 17, 18 21, 26

Description SEPARATOR BELLOWS SEALED STOP VALVE STRAINER (flanged) PRESSURE GAUGE PRESSURE REDUCING VALVE SAFETY VALVE SANITARY FILTER SANITARY STEAM TRAP ISOLATING Globe type VALVE Piston type (screwed) Ball type LIFT CHECK VALVE FLOAT TRAP SPIRATEC SENSOR CHAMBER STRAINER (screwed) AIR VENT BALANCED PRESSURE STEAM TRAP

Bronze

Cast iron SG iron Steel Stainless steel S3 1808 or S5 1808 or S6 BSA1 BSA2 BSA3 Fig 3 Fig 33 Fig 37 Fig 34 Fig 36 100 mm diameter Spirax Sarco pressure gauge with 'U' or ring syphon DP17TE SV57 SV3 or SV54 CSF16 BTM7, BT6, BTS7 or BTD52L HV3 A3S RP31 M10 M10 LCV1 LCV2 FT14 ST171 ST141 ST161 Fig 1 or 12 Fig 12SG Fig 14 Fig 16 AV13 AV21

Selection of products subject to maximum pressure and temperature ratings. In the interests of development and improvement of products, we reserve the right to change the specification.

18

BPT21Y

© Copyright 1998

Hospitals: Heating Cabinet Temperature Control

1

2

3

4

5

10 6

7

8

9 11 Condensate

12

13

14

Steam in Condensate

Table of parts Part No. 1 2 3 4

5, 10, 12 6 7, 14 8 9 13 11

Description SEPARATOR BELLOWS SEALED STOP VALVE STRAINER (flanged)

Bronze

Fig 3

SG iron BSA2 Fig 37

KA33 or KB33

CONTROL VALVE ISOLATING Globe type VALVE Piston type (screwed) Ball valve STRAINER (screwed) SPIRATEC SENSOR CHAMBER FLOAT TRAP LIFT CHECK VALVE BALANCED PRESSURE THERMOSTATIC STEAM TRAP CONTROL SYSTEM

Cast iron S3 BSA1 Fig 33

HV3

Fig 1 or 12

LCV1

Fig 13

Fig 12SG ST171 FT14

Steel 1808 or S5 BSA3 Fig 34 KA43, KB43 or KC43 A3S RP31 M10 Fig 14 ST141

Stainless steel 1808 or S6 Fig 36

M10 Fig 16 ST161 FT16

LCV2 BPT21Y or BPT30Y Type 121, 122, 123 or 128 self-acting control

Selection of products subject to maximum pressure and temperature ratings. In the interests of development and improvement of products, we reserve the right to change the specification.

© Copyright 1998

19

Textile Industry: Canopy Drier Flash Recovery 1

2

3

4

6 Vac

High presure steam

7

Condensate

13

5 14

15

8 9 10 11 12 Main coil 16 Frost coil

Air flow

17

18 19

20

25 21 22 23 24

26 27 28 29 30 Condensate to vented receiver

Table of parts Part No. 1 2 3 4 5 6 7 8, 13, 16, 21, 26 9, 22, 27 10, 18, 23, 28 11, 19, 24, 29 12, 17, 20, 30 14 15 25

Description SEPARATOR BELLOWS SEALED STOP VALVE STRAINER (flanged) ACTUATOR CONTROL VALVE CONTROLLER VACUUM BREAKER ISOLATING Globe type VALVE Piston type (screwed) Ball type LIFT CHECK VALVE FLOAT TRAP SPIRATEC SENSOR CHAMBER STRAINER (screwed) AIR VENT TEMPERATURE SENSOR FLASH VESSEL

Bronze

Fig 3

Cast iron

SG iron

VB14 HV3

FT 14 ST171 Fig 12SG

ST141 Fig 14 AV21 Spirax Sarco Pt100 temperature sensor Spirax Sarco FV type flash vessel

Selection of products subject to maximum pressure and temperature ratings. In the interests of development and improvement of products, we reserve the right to change the specification.

20

Stainless steel 1808 or S6 Fig 36 KE63 VB 21

A3S RP31 M10 LCV2

LCV1

Fig 1 or 12 AV13

Steel

S3 1808 or S5 BSA1 BSA2 BSA3 Fig 33 Fig 37 Fig 34 Spirax Sarco EL5500 series actuator KE73 KE43 ELSX series Spirax Sarco controller

M10

ST161 Fig 16

© Copyright 1998

HVAC: Air Heater Batteries - Multi-Unit Installation 1

2

3

4

6

7

EL T

Steam 5 14 15

13 8 9 10 11 12

Air flow

Air handling unit

17 18 19 20

16

Condensate to vented receiver

Table of parts Part No. 1 2 3 4 5 6 7 8, 13, 14, 17 9, 16 10, 20 11, 19 12, 18 15

Description SEPARATOR BELLOWS SEALED STOP VALVE STRAINER (flanged) ACTUATOR CONTROL VALVE VACUUM BREAKER CONTROLLER ISOLATING Globe type VALVE Piston type (screwed) Ball type STRAINER (screwed) SPIRATEC SENSOR CHAMBER FLOAT TRAP LIFT CHECK VALVE TEMPERATURE SENSOR

Bronze

Fig 3

Cast iron S3

SG iron

Steel 1808 or S5

BSA1

BSA2

BSA3

Fig 33 Fig 37 Fig 34 Spirax Sarco EL5500 series actuator KE73 KE43

VB14 HV3

Fig 1 or 12

LCV1

Spirax Sarco ELSX65 controller A3S RP31 M 10 Fig 12SG Fig 14 ST171 ST141 FT14 FT44 LCV2 Spirax Sarco Pt100 temperature sensor

Selection of products subject to maximum pressure and temperature ratings. In the interests of development and improvement of products, we reserve the right to change the specification.

Stainless steel 1808 or S6

Fig 36 KE63 VB21

M10 Fig 16 ST161 FT16

© Copyright 1998

21

Food Industry: Jacketed Pan Assembly

1

2

3

4

5

6

7

Steam in Air vent to a safe place

Jacketed pan

8

9

10

11

12

13 Condensate to vented receiver

Table of parts Part No.

Description

2, 9 3 4 5 7 10

Globe type ISOLATING Piston type VALVE Ball type STRAINER PRESSURE REDUCING VALVE PRESSURE GAUGE SAFETY VALVE AIR VENT SPIRATEC SENSOR CHAMBER

11

STEAM TRAP

12

CHECK VALVE

1, 6, 8, 13

Bronze HV3

Cast iron

SG iron

Stainless steel

M10 Fig 12SG Fig 16 BRV2 100 mm diameter Spirax Sarco pressure gauge with 'U' or ring syphon pipe SV3 SV3 AV13 AV21 ST171 ST141 ST161 BPT21 or FT14 BPT30 LCV1 LCV2

Fig 1 or 12

Selection of products subject to maximum pressure and temperature ratings. In the interests of development and improvement of products, we reserve the right to change the specification.

22

Steel A3S RP31 M10 Fig 14

© Copyright 1998

Dairy Industry: Pasteuriser Control Note: Control systems not shown.

1

2

4

6

7 Heating water in

out

3 Steam

5

8 9 Condensate

10 11 12

Unpasteurised milk

Pasteurised milk

13

18 19 Cooling water in 14

15 16 17

out

Table of parts Part No. 1, 7, 8, 13, 14, 17 2, 12, 16 3, 19 4, 18 5, 15 6 9 10 11

Description Globe type ISOLATING Piston type VALVE Ball type STRAINER POSITIONER ACTUATOR CONTROL VALVE VACUUM BREAKER LIFT CHECK VALVE FLOAT TRAP SPIRATEC SENSOR CHAMBER

Bronze HV3

Fig 1 or 12

Cast iron

SG iron

Steel A3S RP31 M10 Fig 12SG Fig 14 EP5 electropneumatic positioner PN5000 series pneumatic actuator KE71

VB14 LCV1

Stainless steel

M10 Fig 16

VB21 LCV2 FT14 ST171

Selection of products subject to maximum pressure and temperature ratings. In the interests of development and improvement of products, we reserve the right to change the specification.

ST141

FT16 ST161

© Copyright 1998

23

Notes

Selection of products subject to maximum pressure and temperature ratings. In the interests of development and improvement of products, we reserve the right to change the specification.

24

© Copyright 1998

Notes

Selection of products subject to maximum pressure and temperature ratings. In the interests of development and improvement of products, we reserve the right to change the specification.

© Copyright 1998

25

Notes

Selection of products subject to maximum pressure and temperature ratings. In the interests of development and improvement of products, we reserve the right to change the specification.

26

© Copyright 1998

Notes

Selection of products subject to maximum pressure and temperature ratings. In the interests of development and improvement of products, we reserve the right to change the specification.

© Copyright 1998

27

Some of the products shown in this guide may not be available in certain markets. In the interests of development and improvement of the products, we reserve the right to change the specification without notice. Spirax-Sarco Limited, Charlton House, Cheltenham, Gloucestershire, GL53 8ER UK Tel: +44 1242 521361 Fax: +44 1242 573342 E mail:[email protected] Internet:www.spirax-sarco.com © Copyright 1998

Spirax Sarco is a registered trademark of Spirax-Sarco Limited

TR-GCM-22

CM Issue 1