tech pack

December 18, 2016 | Author: Shubham Aryan | Category: N/A
Share Embed Donate


Short Description

important for niftians...

Description

SEASON: AW’ 07

PRODUCT PACK - DRESS SHIRTS

PRODUCT: STYLE NO.

FABRIC

Department

REGULAR COLLAR WITH ROUND CUFF RAY 001

100 % COTTON FABRICS 100% LINEN FABRICS

Approved by:

Signature

CONTENTS PRODUCT DETAILS STYLE LINES BLOCK DETAILS, SPEC SHEET & MEASUREMENT GUIDELINE CONSTRUCTION DETAILS BUTTON PLACEMENTS LABEL PLACEMENTS FOLDING & PACKING TRIM LIST

Date:

Product Sourcing Quality N.B.: Any amendment should be in consultation/agreement between all the departments mentioned above. Any queries regarding the product pack can be marked to product department on the following address:

Style lab,Raymond Apparel Ltd., Jekegram, Pokhran Road no.1, Thane-400606 , Mahrashtra, India. Ph: 25988050,25988015.

STYLE LAB RAYMOND APPAREL LIMITED. Jekegram Thane.

1 2 3 4-8 9 10 11 12

RAY 001 2

STYLE LINE

LONG SLEEVES DRESS SHIRT WITH REGULAR COLLAR ROUND CUFF.

42

Garment style lines: Double fused Regular collar with Removable collar stays. Round corner Pocket , Convertible Barrel cuffs, fused cut & sew center placket. SPI 18 for all top stitches Thread: 150tkt PPC spun Body & Button Hole thread to be DTM to basie fabric. Button & main label threads to be DTM to button & main label respectively. Buttons : 16L & 14L, 4 hole DTM Buttons. ( P0428/P695., P0839/P6957). For DTM & Button Type refer to trim card THREAD: 95m. For Branding Embroidery thread to be Madeira Poly neon / Calypso: 3 Mrts. INTERLINING: 25cm (90cm width) Collar Skin, Band & Cuff - DHJ 285 ES Consumption : 17cm., Collar Patch & Placket - DHJ Polystar 2.28.23.464 ES Consumption : 8cm

STYLE LAB RAYMOND APPAREL LIMITED. Jekegram Thane.

STYLE LINE

RAY 001 2.1

SHORT SLEEVES DRESS SHIRT WITH REGULAR COLLAR ROUND CUFF.

42

Garment style lines: Double fused Regular collar with Removable collar stays. Round corner Pocket , fused cut & sew center placket. SPI 18 for all top stitches Thread: 150tkt PPC spun Body & Button Hole thread to be DTM to basic fabric. Button & main label threads to be DTM to button & main label respectively. Buttons : 16L & 14L, 4 hole DTM Buttons. ( P0428/P695., P0839/P6957). For DTM & Button Type refer to trim card THREAD: 75m. For Branding Embroidery thread to be Madeira Poly neon / Calypso: 3 Mrts. INTERLINING: 20cm (90cm width) Collar Skin, Band & Cuff - DHJ 285 ES Consumption : 12cm. Collar Patch & Placket - DHJ Polystar 2.28.23.464 ES Consumption : 8cm

STYLE LAB RAYMOND APPAREL LIMITED. Jekegram Thane.

BLOCK DETAILS, SPEC SHEET & MEASUREMENTS GUIDE LINES

RAY 001 3

BLOCK DETAILS: Body: Raymond ; Collar: C-01 RY REGULAR; C-band: CB-01 RY Pocket: PK-01 RY . Cuff: CF 00 RY

SPEC SHEET Code

MESUREMENT GUIDELINE

Description

Size 39 39.50

40 40.50

42 42.50

44 44.50

46 46.50 0.50

Collar Height at CB

4.50

4.50

4.50

4.50

4.50 0.00

3

Collarband height at CB

3.50

3.50

3.50

3.50

3.50 0.00

4

Collar point

7.50

7.50

7.50

7.50

7.50 0.00

5

tie space

0.50

0.50

0.50

0.50

0.50 0.20

6

Collar bottom measurement

39.00

40.00

42.00

44.00

46.00 0.30

7

Collar band bottom measurement

43.70

44.70

46.70

48.70

50.70 0.30

1

Collar button to buttonhole.

2

5

Tol (+/-)

8

Collar spread

10.50

10.50

10.50

10.50

10.50 0.70

9

1/2 Chest

58.50

60.00

63.00

66.00

69.00 1.00

10

1/2 Waist

55.50

57.00

60.00

63.00

66.00 1.00

11

1/2 Bottom

56.50

58.00

61.00

64.00

67.00 1.00

12

CB length

79.50

80.00

81.00

82.00

83.00 1.00

13

CF length band dow n

69.90

70.30

71.10

71.90

72.70 1.00

14

Yoke height at CB

11.50

11.50

11.50

11.50

11.50 0.30

15

Back Shoulder Length

47.25

48.00

49.50

51.00

52.50 0.50

16

1/2 Armhole Curve

26.50

27.00

28.00

29.00

30.00 0.50

17

Long Sleeve Length From C.B.N

87.38

88.00

89.25

90.50

90.75 1.00

18

Sleeve Length from shoulder

63.75

64.00

64.50

65.00

64.50 1.00

19

Cuff length

24.50

25.00

26.00

27.00

28.00 0.50

20

cuff height

7.00

7.00

7.00

7.00

7.00 0.00

21

1/2 Cuff Length Closed

11.00

11.25

11.75

12.25

12.75 0.30

22

Pocket from shoulder seam

21.50

22.00

22.00

22.50

22.50 0.50

23

Pocket from CF

4.50

5.00

5.00

5.50

5.50 0.50

NOTE: 1. Chest (at armhole), waist, & bottom measurements are with seam pressed back, from edge to edge as shown in fig alongside 2. Collar btn to btnhole measurement is from inside of buttonhole bar to centre of button.

1 4

2

6

8

3 7

22 23 19

20

15

14

17 16 9 20 cm

18

12

13 10

11

3. All measurements are in centimetres.

21

RAY 001 3.1

BLOCK DETAILS, SPEC SHEET & MEASUREMENT GUIDELINE

BLOCK DETAILS: Body: Raymond ; Collar: C-01 RY REGULAR; C-band: CB-01 RY Pocket: PK-01RY

MESUREMENT GUIDELINE

SPEC SHEET Cod e

Description

5

Size 39 39.50

40 40.50

42 42.50

44 44.50

46 46.50

Tol (+/-)

1

Collar button to buttonhole.

2

Collar Height at CB

4.50

4.50

4.50

4.50

4.50

0.00

3

Collarband height at CB

3.50

3.50

3.50

3.50

3.50

0.00

4

Collar point

7.50

7.50

7.50

7.50

7.50

0.00

5

tie space

0.50

0.50

0.50

0.50

0.50

0.20

6

Collar bottom measurement

39.00

40.00

42.00

44.00

46.00

0.30

7

Collar band bottom measurement

43.70

44.70

46.70

48.70

50.70

0.30

8

Collar spread

10.50

10.50

10.50

10.50

10.50

0.70

9

1/2 Chest

58.50

60.00

63.00

66.00

69.00

1.00

10

1/2 Waist

56.50

57.00

60.00

63.00

66.00

1.00

11

1/2 Bottom

56.50

58.00

61.00

64.00

67.00

1.00

12

CB length

79.50

80.00

81.00

82.00

83.00

1.00

13

CF length band dow n

69.90

70.30

71.10

71.90

72.70

1.00

14

Yoke height at CB

11.50

11.50

11.50

11.50

11.50

0.30

15

Back Shoulder Length

47.25

48.00

49.50

51.00

52.50

0.50

16

1/2 Armhole Curve

26.50

27.00

28.00

29.00

30.00

0.50

17

Sleeve Opening Round

37.00

38.00

40.00

42.00

44.00

0.50

18

Sleeve Length from shoulder

23.50

24.00

25.00

26.00

27.00

1.00

19

Sleeve Length from CBN

47.13

48.00

49.75

51.50

53.25

0.50

20

Pocket from shoulder seam

21.50

22.00

22.00

22.50

22.50

0.50

21

Pocket from CF

4.50

5.00

5.00

5.50

5.50

0.50

1

0.50

NOTE: 1. Chest (at armhole), waist, & bottom measurements are with pressed back, from edge to edge as shown in fig alongside 2. Collar btn to btnhole measurement is from inside of buttonhole bar to centre of button.

4

2

6

8

3 7

20 21

15 19 16

18

9 17

20 cm

13 10

11

3. All measurements are in centimetres.

14

12

CONSTRUCTION DETAILS - COLLAR & COLLAR BAND

FABRIC SKIN PATCH

RAY 001 4

COLLAR - C 01 RY

3mm fabric allowance

6mm

8.1 cm trimmed Collar point 7.5cm finished Collar point

1.5mm runstitch

5mm breakline 6mm

 6mm trim allowance

INTERLINING CUTTING DETAILS COLLAR SKIN - cut on true bias 45 degree COLLAR PATCH - cut on grain COLLAR BAND - cut on true bias 45 degree CUFF - cut on grain CENTRE PLACKET - cut on grain

2.5 cm leg

3mm fabric allowance

BREAK LINE FINISH LINE TRIM LINE

COLLARBAND - CB 01RY

1cm

6mm

FINISH LINE

CONSTRUCTION DETAILS - COLLAR & COLLAR BAND

RAY 001 5

COLLAR - C 01 RY 5 mm 1mm

COLLARBAND - CB 01 RY Top stitch band & lock here. Begin ‘finish collar’ here & end on same point on the other side Back tack ends.

5 mm

1mm

2.5”x3/8”x0.35mm Branded Nylon collar Stays

CONSTRUCTION DETAILS - CUFF

RAY 001 7

1.5cm fabric allowance

FABRIC

SKIN CUFF - CF-00 RY

6mm

1.5mm runstitch

4mm fabric allowance 1mm cuff attach

1cm Lock here, towards the button side of cuff

5 mm stitch

3mm

CONSTRUCTION DETAILS - POCKET, FRONTS & BACK

6mm

RAY 001 6

L & R FRONTS

2.5 cm

5 mm 1mm

POCKET - PK 01 RY

14 cm 2.5cm 5 mm

3.5cm

13 cm

3.5cm

1cm full roled hem For Both L/S &

5 mm

1mm

4-5 stitches backtack

1 cm YOKE & BACK 1 cm

NO PLEAT AT BACK

3.5cm 2 cm

CONSTRUCTION DETAILS - SLEEVE & SLEEVE PLACKET

RAY 001

8 1.25 cm

ATTACH SLEEVE TO BODY

UPPER & UNDER SLEEVE PLACKET 2.5 cm

Body

Start here with 3 stitches to lock 16.5 cm

2 cm

Hem Detail For S/S Shirt 2.3cm

1.25 cm

SNCS

Sleeve

1mm

1.25 cm 1.0 cm

TOPSTITCH SLEEVE

Body

2.5 cm hem height

1.0 cm 1mm

2.5 cm

1.0 cm 5mm or 3/16” gauge

SIDE SEAM

SNCS

Sleeve SNCS

Side seam: Feed of the arm, front. over back on both sides.

DNCS

BUTTON PLACEMENTS RAY 001 9 FOR BUTTON TYPE & LIGNE REFER TO TRIM CARD

BUTTON PLACEMENTS

Collar btn to be in line withbtns on placket. Adjust slightly to maintain vertical line balancing in plaid & striped fabrics 6.5 cm 9.0 cm 9.0 cm cm 1.75 cm

Spare buttons 1.5 cm 7.5 cm

Last button hole is horizontal

All button holes to have Purl stitch formation 1.75 cm

1.75 cm

All btns to be sewn with cross lock stitch. Button sew thread to be dtm to button. Provide adequate stemming to buttons.

16L buttons 7 + 1 14L buttons 2+1 NOTE: Sew 16L Buttons with laser Branding on wearer’s Right cuff.

1.45 cm to outer edge of Button hole bar

6.3 cm

6.3 cm 2.5 cm 4.5 cm

1.0 cm to outer edge of Button hole bar

LABEL PLACEMENTS

RAY 001 10

4

40cm

4.5 cm

3.5 cm

3.5cms, centered at CB to center of the embroidery & Thread as for the DTM ( Thread to be used Poly neon)

Wash Care label to be inserted Left Wearer side inside the Feed of the arm. Egyptian Giza Cotton

Only for 100% Cotton Fabrics

Wash care

10 cm

1.5 cm

FOLDING & PACKGING

RAY 001 11 Insert 1-Pearl head 2-Metal cross clip to hold pin and 1-White tail ( one end inserted in Plastic “M-clip” to hole of back support) hold sleeves inside

FOR TAGS REFER TO TRIM CARDS

Raymond Back Supporter

42

TUCK IN TAIL (Tail to be laid flat inside)

Pearl-head pins to be inserted from the top of the back support

Ba co r ta de g

1-Metal cross clip to hold cuff, to be placed beneath sleeve placket & cuff .

36cm (+/-0.3)

r olla e re c p Spa envelo stay

g g Ta Han

NOT TO BE VISIBLE EITHER ON FRONT OR BACK

Two long printed tissue paper BOPP Poly bag to be used.

Hang tag to be put on 1st button hole ( excluding neck button) Using Branded locking loop

Bar Code Tag & Spare Collar Stay Envelope on last but one button

23 cm (+/-0.3) Cuff to be aligned with bottom of board

COLLAR SIZE TAB TO BE STUCKED IN THE CENTER OF THE COLLAR

PVC band dented side towards CF Branded collar Strip to be inserted under PVC band

Cardboard neckband, longer edge up Blend label

40

40

Note: Metal clips -made of rust proof non corrosive metal with smooth edges. Metal pins -made of rust proof non corrosive with plastic silver head

042 R BUTTERFLY

Bottom edge of band to be aligned after pinning

1-silver plastic head pin at neck band, tuck in-out-in with~1.5cm bite outside

FOLDING & PACKGING

RAY 001 11.1 Insert 1-Pearl head 2-Metal cross clip to hold pin and 1-White tail ( one end inserted in Plastic “M-clip” to hole of back support) hold sleeves inside

FOR TAGS REFER TO TRIM CARDS

Raymond Back Supporter

42

TUCK IN TAIL (Tail to be laid flat inside)

Ba co r ta de g

Pearl-head pins to be inserted from the top of the back support

36cm (+/-0.3)

NOT TO BE VISIBLE ON BACK

r olla e re c p Spa envelo stay

g g Ta Han

1-Metal cross clip to hold sleeve

Hang tag to be put on 1st button hole ( excluding neck button) Using Branded locking loop

Two long printed tissue paper BOPP Poly bag to be used.

Bar Code Tag & Spare Collar Stay Envelope on last but one button

23 cm (+/-0.3) Cuff to be aligned with bottom of board

COLLAR SIZE TAB TO BE STUCKED IN THE CENTER OF THE COLLAR

PVC band dented side towards CF Branded collar Strip to be inserted under PVC band

Cardboard neckband, longer edge up Blend label

40

40

Note: Metal clips -made of rust proof non corrosive metal with smooth edges. Metal pins -made of rust proof non corrosive with plastic silver head

042 R BUTTERFLY

Bottom edge of band to be aligned after pinning

1-silver plastic head pin at neck band, tuck in-out-in with~1.5cm bite outside

View more...

Comments

Copyright ©2017 KUPDF Inc.
SUPPORT KUPDF