SOP XGPON ALU Provisioning v1 13112014(1)

Standard Operating Procedure Provisioning XGPON ALU 7360 ISAM

PT. Lintas Teknologi Indonesia th Menara MTH 16 Floor Jl. MT Haryono Kav. 23 Jakarta 12820 - Indonesia Telp. +62 21 8378 0000 Fax. +62 21 8378 0001 http://www.lt-indonesia.com 2013

Standard Operating Procedure

DOCUMENT CONTROL Author Change Authority Revision History

: Rendi : :

Version Number

Date Issued

Status

Editor

Reason for Change

1

26-10-2014

Draft

Rendi

Draft

Reviewers: Name

Organization

Department

Review Date

Approvals: Name

Organization

Department

Approval Date

Change Forecast: Low

Intellectual Property Rights This document contains valuable trade secrets and confidential information of ALU and its partners, and shall not be disclosed to any person, organization, or entity unless such disclosure is subject to the provisions of a written nondisclosure and proprietary rights agreement or intellectual property license agreement approved by ALU or LINTAS. The distribution of this document does not grant any license in or rights, in whole or in part, to the content, the product (s), technology, or intellectual property described herein.

XGPON ALU 7360 ISAM Provisioning SOP

2

Standard Operating Procedure

Table of Contents DOCUMENT CONTROL

2

1.

INTRODUCTION

6

2.

PERSON IN CHARGE (PIC)

6

3.

PROVISIONING

7

3.1 I-240W-A ONT 3.1.1 TOPOLOGY 3.1.2 CONNECTIONS AND COMPONENTS 3.1.3 CREATE/MODIFY/DELETE ONT 3.1.4 CREATE/MODIFY/DELETE INTERNET SERVICE (PPPoE) 3.1.5 CREATE/MODIFY/DELETE IPTV SERVICE 3.1.6 CREATE/MODIFY/DELETE VOICE SERVICE

7 7 7 9 9 9 10

3.2 O-16160E-Q ONT 3.2.1 TOPOLOGY 3.2.2 CONNECTIONS AND COMPONENTS 3.2.3 CREATE/MODIFY/DELETE ONT 3.2.4 CREATE/MODIFY/DELETE INTERNET SERVICE (BRIDGE) 3.2.5 CREATE/MODIFY/DELETE IPTV SERVICE 3.2.6 CREATE/MODIFY/DELETE VOICE SERVICE

11 11 11 13 13 13 14

3.3 B-2404-P ONT 3.3.1 TOPOLOGY 3.3.2 CONNECTIONS AND COMPONENTS 3.3.3 CREATE/MODIFY/DELETE ONT 3.3.4 CREATE/DELETE E1 SERVICE

15 15 15 17 17

3.4 POINT TO POINT (P2P) (NELT-B) 3.4.1 TOPOLOGY 3.4.2 CONNECTIONS AND COMPONENTS 3.4.3 CREATE/MODIFY/DELETE TAGGED VLAN SERVICE

19 19 19 22

4.

APPENDIX: PROVISIONING FLOW

XGPON ALU 7360 ISAM Provisioning SOP

23

3

Standard Operating Procedure

List of Figures FIGURE 1 PHYSICAL TOPOLOGY OF I-240W-A INDOOR ONT AT PT. TELKOM INDONESIA FIGURE 2 I-240W-A INDOOR ONT PHYSICAL CONNECTIONS (BACK VIEW) FIGURE 3 I-240W-A INDOOR ONT PHYSICAL CONNECTIONS (SIDE VIEW) FIGURE 4 I-240W-A INDOOR ONT LEDS FIGURE 5 PHYSICAL TOPOLOGY OF O-16160E-Q MDU ONT AT PT. TELKOM INDONESIA FIGURE 6 PHYSICAL CONNECTIONS ON THE FRONT OF O-16160E-Q MDU ONT FIGURE 7 PHYSICAL CONNECTIONS ON THE BACK OF O-16160E-Q MDU ONT FIGURE 8 O-16160E-Q MDU ONT LEDS FIGURE 9 PHYSICAL TOPOLOGY OF E1 SFP TO B-2404-P ONT AT PT. TELKOM INDONESIA FIGURE 10 PHYSICAL CONNECTIONS FOR B-2404-P BUSINESS ONTS FIGURE 11 B-2404-P BUSINESS ONT LEDS FIGURE 12 PHYSICAL TOPOLOGY OF P2P AT PT. TELKOM INDONESIA FIGURE 13 FRONT VIEW OF THE NELT-B FIGURE 14 BOARD LEDS ON THE NELT-B FIGURE 15 LEDS FOR SFP PORTS FIGURE 16 PHYSICAL OF 1000BASE-LX SFP FIGURE 17 CREATE ONT FLOW FIGURE 18 MODIFY ONT SERIAL NUMBER FLOW FIGURE 19 DELETE ONT FLOW FIGURE 20 CREATE INTERNET SERVICE FLOW (PPPOE) FIGURE 21 MODIFY SERVICE BANDWIDTH FLOW FIGURE 22 MODIFY INTERNET PPPOE USERNAME AND PASSWORD FLOW FIGURE 23 DELETE INTERNET SERVICE FLOW (PPPOE) FIGURE 24 CREATE INTERNET SERVICE FLOW (BRIDGE) FIGURE 25 DELETE INTERNET SERVICE FLOW (BRIDGE) FIGURE 26 CREATE IPTV SERVICE FLOW FIGURE 27 DELETE IPTV SERVICE FLOW FIGURE 28 CREATE VOICE SERVICE FLOW FIGURE 29 MODIFY POTS PORT FLOW FIGURE 30 DELETE VOICE SERVICE FLOW FIGURE 31 CREATE E1 SERVICE FLOW FIGURE 32 DELETE E1 SERVICE FLOW FIGURE 33 CREATE POINT TO POINT TAGGED VLAN FLOW FIGURE 34 DELETE POINT TO POINT TAGGED VLAN FLOW

XGPON ALU 7360 ISAM Provisioning SOP

7 7 7 8 11 11 11 12 15 15 16 19 19 19 20 20 23 23 23 23 24 24 24 24 25 25 25 26 26 26 27 28 29 29

4

Standard Operating Procedure

List of Tables TABLE 1 I-240W-A INDOOR ONT PHYSICAL CONNECTIONS TABLE 2 I-240W-A INDOOR ONT LEDS TABLE 3 O-16160E-Q MDU ONT PHYSICAL CONNECTIONS TABLE 4 O-16160E-Q MDU ONT LEDS TABLE 5 B-2404-P BUSINESS ONT CONNECTIONS TABLE 6 B-2404-P BUSINESS ONT LED DESCRIPTIONS TABLE 7 LED DEFINITION FOR THE NELT-B TABLE 8 BEHAVIOR OF LEDS FOR SFP PORTS TABLE 9 OPTICAL PARAMETERS FOR ALCATEL-LUCENT APPROVED OPTICAL MODULES TABLE 10 1000BASE-LX OPTICAL MODULE PARAMETERS

XGPON ALU 7360 ISAM Provisioning SOP

8 8 11 12 15 16 19 20 21 21

5

1. INTRODUCTION

Standard Operating Procedure

This document has been prepared for reference of XGPON ALU 7360 provisioning at PT Telkom Indonesia. 2. PERSON IN CHARGE (PIC) Name Rendi

Company PT. Lintas Teknologi Indonesia

XGPON ALU 7360 ISAM Provisioning SOP

Phone Number +62 82233167779

Roles and Responsibilities Senior Access Engineer

6

3. 3.1

PROVISIONING I-240W-A ONT

3.1.1

TOPOLOGY

Standard Operating Procedure

Figure 1 Physical topology of I-240W-A indoor ONT at PT. Telkom Indonesia

Home Connection

FTM

I-240W-A ONT Eth#1

nd

IPTV

Eth#2

SIP Phone

PON

7360 ISAM FX OLT

2

Splitter Splitter 1:4 1:8

Eth#3 POTS#1

Internet

POTS#2 Eth#4

st

1 IPTV

3.1.2

CONNECTIONS AND COMPONENTS Figure 2 I-240W-A indoor ONT physical connections (back view)

Figure 3 I-240W-A indoor ONT physical connections (side view)

XGPON ALU 7360 ISAM Provisioning SOP

7

Table 1 I-240W-A indoor ONT physical connections

Standard Operating Procedure

Connection

Description

Ethernet ports

This connection is provided through Ethernet RJ-45 connectors. Up to four 10/100 Base-T Ethernet interfaces are supported. The Ethernet ports can support both data and in-band video services on all four interfaces.

Fiber optic

This connection is provided through an SC/APC fiber optic connector.

LED button

This buttons turns all LEDs on or off.

POTS

This connection is provided through RJ-11 ports. Up to two POTS connections are supported. The POTS ports support voice services. Wi-Fi service is compliant with IEEE 802.11 standards and is enabled and disabled using a Wireless button. The Wi-Fi Protected Setup button is labeled WPS. This button enables and disables WLAN data encryption.

Wireless button WPS button Power

This connection is provided through the power connector. A power cable fitted with a barrel connector is used to make the connection.

USB ports

This connection is provided through 2 USB ports.

Figure 4 I-240W-A indoor ONT LEDs

Table 2 I-240W-A indoor ONT LEDs Indicator PWR Link Auth LAN 1 to 4 TEL 1 to 2 VOIP WPS

WLAN

LED color and behavior

LED behavior description

Green solid Off Green solid Off Green solid Off Green solid Off

Operating on AC power No power source GPON link is OK GPON link is not OK ONT is authorized ONT is not authorized Ethernet is linked ONT power off or Ethernet not connected

Green solid Green flashing Off

Off hook Call in On hook

Green solid Off Green solid Red Off

VOIP is OK VOIP is not OK "In Progress" or "Success" status "Error" and "Session Overlap" status WPS not activated

Green solid Green flashing Off

Wireless enabled Traffic on wireless interface Wireless disabled

XGPON ALU 7360 ISAM Provisioning SOP

8

USB

Green solid Green flashing Off

One or more USB device is connected One or more USB device is connected with traffic No USB device connected

INTERNET

Green solid Off

HSI WAN is connected HSI WAN is not connected

Standard Operating Procedure

3.1.3 CREATE/MODIFY/DELETE ONT a. Create configure equipment ont interface 1/1/// sw-ver-pland 3FE54869ACEC29 sernum subslocid WILDCARD voip-allowed iphost cvlantrans-mode local configure equipment ont interface 1/1/// admin-state up configure equipment ont slot 1/1////14 planned-card-type veip plndnumdataports 1 plndnumvoiceports 0 admin-state up configure equipment ont slot 1/1////1 planned-card-type 10_100base plndnumdataports 8 plndnumvoiceports 0 admin-state up configure equipment ont slot 1/1////2 planned-card-type pots plndnumdataports 0 plndnumvoiceports 2 admin-state up

b. Modify ONT Serial Number configure equipment ont interface 1/1/// admin-state down configure equipment ont interface 1/1/// sernum configure equipment ont interface 1/1/// admin-state up

c. Delete configure equipment ont interface 1/1/// admin-state down configure equipment ont no interface 1/1///

3.1.4 CREATE/MODIFY/DELETE INTERNET SERVICE (PPPoE) a. Create configure qos interface 1/1////14/1 upstream-queue 0 bandwidth-profile name: configure qos interface 1/1////14/1 queue [0...3] shaper-profile name: configure interface port uni:1/1////14/1 admin-up configure bridge port 1/1////14/1 max-unicast-mac 4 configure bridge port 1/1////14/1 vlan-id 881 vlan-scope local networkvlan single-tagged configure veip ont 1/1////14/1 domain-name admin-state up configure ntp ont 1/1/// key

b. Modify Bandwidth configure qos interface 1/1////14/1 upstream-queue 0 bandwidth-profile name: configure qos interface 1/1////14/1 queue [0...3] shaper-profile name:

c. Modify PPPoE Username and Password configure veip ont 1/1////14/1 domain-name configure ntp ont 1/1/// key

d. Delete configure configure configure configure configure configure

ntp ont 1/1/// no key veip ont 1/1////14/1 no domain-name no admin-state bridge no port 1/1////14/1 interface port uni:1/1////14/1 no admin-up qos interface 1/1////14/1 queue [0...3] shaper-profile none qos interface 1/1////14/1 upstream-queue 0 no bandwidth-profile

3.1.5 CREATE/MODIFY/DELETE IPTV SERVICE a. Create configure qos interface 1/1////1/4 upstream-queue 0 bandwidth-profile name: configure qos interface 1/1////1/4 queue [0...3] shaper-profile name: configure interface port uni:1/1////1/4 admin-up configure bridge port 1/1////1/4 max-unicast-mac 4 configure bridge port 1/1////1/4 vlan-id 111 configure bridge port 1/1////1/4 pvid 111 configure igmp channel vlan:1/1////1/4:111 max-num-group 2 configure igmp channel vlan:1/1////1/4:111 preview-packages "[1...1024]"

XGPON ALU 7360 ISAM Provisioning SOP

9

b. Modify Bandwidth configure qos interface 1/1////1/4 upstream-queue 0 bandwidth-profile name: configure qos interface 1/1////1/4 queue [0...3] shaper-profile name:

Standard Operating Procedure

c. Delete configure configure configure configure

bridge no port 1/1////1/4 interface port uni:1/1////1/4 no admin-up qos interface 1/1////1/4 queue [0...3] shaper-profile none qos interface 1/1////1/4 upstream-queue 0 no bandwidth-profile

3.1.6 CREATE/MODIFY/DELETE VOICE SERVICE a. Create configure qos interface 1/1////voip upstream-queue 0 bandwidth-profile name:VOIP_UP-1M configure qos interface 1/1////voip queue [0...3] shaper-profile name:VOIP_DN-1M configure bridge port 1/1////voip configure bridge port 1/1////voip vlan-id vlan-scope network tag untagged configure bridge port 1/1////voip pvid configure bridge port 1/1////vuni max-unicast-mac 2 configure iphost ont ont:1/1////1 dhcp enabled vlan configure iphost ont ont:1/1////1 admin-state up configure voice ont voip-config ont:1/1////1 protocol sip conf-method omci configure voice ont sip-config ont:1/1////1 proxyserv-prof 20 outproxyserv-prof 20 reg-expire-time 3600 re-reg-head-start 360 aor-host-prt-prof 21 registrar-prof 24 uri-format sip-uri dscp 46 opt-tx-cntrl disable configure voice ont voice-sip-port 1/1////2/1 user-aor username @telkom.net.id display-name password realm telkom.net.id ac-code-prof 2 app-serv-prof 8 ntwk-dp-prof 13 configure voice ont voice-port 1/1////2/1 voipconfig sip voip-media-prof 3 admin-state unlocked

b. Modify POTS Number configure voice ont pots 1/1////2/1 admin-state locked configure voice ont voice-sip-port 1/1////2/1 user-aor user-name @telkom.net.id display-name password realm telkom.net.id ac-code-prof 2 app-serv-prof 8 ntwk-dp-prof 13 configure voice ont pots 1/1////2/1 admin-state unlocked

c. Delete configure voice ont pots 1/1////2/1 admin-state locked configure voice ont voice-sip-port 1/1////2/1 user-aor none user-name none display-name none password none realm telkom.net.id no ac-code-prof no app-serv-prof no ntwk-dp-prof configure voice ont voice-port 1/1////2/1 voip-media-prof none configure bridge no port 1/1////voip configure qos interface 1/1////voip queue [0...3] shaper-profile none configure qos interface 1/1////voip upstream-queue 0 no bandwidth-profile

XGPON ALU 7360 ISAM Provisioning SOP

10

3.2

O-16160E-Q ONT

3.2.1

TOPOLOGY Figure 5 Physical topology of O-16160E-Q MDU ONT at PT. Telkom Indonesia

Standard Operating Procedure

Eth#1

2

Connection O-16160E-Q ONT

FTM

nd

IPTV

Eth#2

SIP Phone

PON

Eth#3

Splitter Splitter 1:4 1:8

7360 ISAM FX OLT

POTS#1 …….. POTS#16

Internet Eth#4

st

1 IPTV …….. ETH#16

3.2.2

CONNECTIONS AND COMPONENTS Figure 6 Physical connections on the front of O-16160E-Q MDU ONT

Figure 7 Physical connections on the back of O-16160E-Q MDU ONT

Table 3 O-16160E-Q MDU ONT physical connections Connection type

Management

Description The first management interface (MGMT) is a craft port where connection is provided through an RJ-45 connector. The second management interface (CONSOLE) is a craft port where connection is provided through an RJ-45 connector.

XGPON ALU 7360 ISAM Provisioning SOP

11

Standard Operating Procedure

Ethernet

This connection is provided through an Ethernet RJ-45 cable. Up to 24 Ethernet connections are supported. The Ethernet ports support both data and in-band video services.

POTS

For the O-24240E-Q, this interface is an RJ-21 connector with 48 positions which support up to 24 POTS lines. For the O-16160E-Q, this interface is an RJ21 connector with 32 positions which support up to 16 POTS lines.

Fiber optic

An SC/APC fiber optic connector terminates a fiber optic connection from the P-OLT.

dc power

This connection is provided through an 8-pin UPS power connector.

grounding lug

This connection is provided through a ground wire connected to the lug.

ac power

This connection is provided by an ac power cord with a three-pronged female plug.

12 V battery backup

This connection is provided by a power cord with a two-pronged female plug.

Figure 8 O-16160E-Q MDU ONT LEDs

Table 4 O-16160E-Q MDU ONT LEDs LED name PWR ALM NET MGMT SIGN RTP MODE LINK

LED color

LED behavior description

Off Green Off Red Off Green Off Green Off Green Off Green Off Green

No power Power on Normal System failure Optical path error 1490 nm data path (downstream) is OK and PLOAM has been exchanged with the OLT ONU is not register to OLT Full communication with ranging sync established between OLT and ONT VoIP not registered VoIP registered All of the POTS ports on-hook One or more of the POTS ports off-hook 10M 100M

Off Yellow Solid Yellow flashing

Link not up Link up Link up and Rx or Tx activity detected

XGPON ALU 7360 ISAM Provisioning SOP

12

Standard Operating Procedure

3.2.3 CREATE/MODIFY/DELETE ONT a. Create configure equipment ont interface 1/1/// sw-ver-pland 3FE53866AOCK26 sernum subslocid WILDCARD voip-allowed iphost cvlantrans-mode local configure equipment ont interface 1/1/// admin-state up configure equipment ont slot 1/1////10 planned-card-type 10_100base plndnumdataports 8 plndnumvoiceports 0 admin-state up configure equipment ont slot 1/1////11 planned-card-type 10_100base plndnumdataports 8 plndnumvoiceports 0 admin-state up configure equipment ont slot 1/1////2 planned-card-type pots plndnumdataports 0 plndnumvoiceports 16 admin-state up

b. Modify ONT S/N (Serial Number) configure equipment ont interface 1/1/// admin-state down configure equipment ont interface 1/1/// sernum configure equipment ont interface 1/1/// admin-state up

c. Delete configure equipment ont interface 1/1/// admin-state down configure equipment ont no interface 1/1///

3.2.4 CREATE/MODIFY/DELETE INTERNET SERVICE (BRIDGE) a. Create configure qos interface 1/1///// upstream-queue 0 bandwidth-profile name: configure qos interface 1/1///// queue [0...3] shaperprofile name: configure interface port uni:1/1///// admin-up configure bridge port 1/1///// max-unicast-mac 4 configure bridge port 1/1///// vlan-id configure bridge port 1/1///// pvid

b. Modify Bandwidth configure qos interface 1/1///// upstream-queue 0 bandwidth-profile name: configure qos interface 1/1///// queue [0...3] shaperprofile name:

c. Delete configure bridge no port 1/1///// configure interface port uni:1/1///// no admin-up configure qos interface 1/1///// queue [0...3] shaperprofile none configure qos interface 1/1///// upstream-queue 0 no bandwidth-profile

3.2.5 CREATE/MODIFY/DELETE IPTV SERVICE a. Create configure qos interface 1/1///// upstream-queue 0 bandwidth-profile name: configure qos interface 1/1///// queue [0...3] shaperprofile name: configure interface port uni:1/1///// admin-up configure bridge port 1/1///// max-unicast-mac 4 configure bridge port 1/1///// vlan-id 111 configure bridge port 1/1///// pvid 111 configure igmp channel vlan:1/1/////:111 max-num-group 2 configure igmp channel vlan:1/1/////:111 preview-packages "[1...1024]"

b. Modify Bandwidth configure qos interface 1/1///// upstream-queue 0 bandwidth-profile name: configure qos interface 1/1///// queue [0...3] shaperprofile name:

c. Delete configure bridge no port 1/1///// configure interface port uni:1/1///// no admin-up configure qos interface 1/1///// queue [0...3] shaperprofile none

XGPON ALU 7360 ISAM Provisioning SOP

13

configure qos interface 1/1///// upstream-queue 0 no bandwidth-profile

Standard Operating Procedure

3.2.6 CREATE/MODIFY/DELETE VOICE SERVICE a. Create configure qos interface 1/1////voip upstream-queue 0 bandwidth-profile name:VOIP_UP-1M configure qos interface 1/1////voip queue [0...3] shaper-profile name:VOIP_DN-1M configure bridge port 1/1////voip configure bridge port 1/1////voip vlan-id vlan-scope network tag untagged configure bridge port 1/1////voip pvid configure bridge port 1/1////vuni max-unicast-mac 2 configure iphost ont ont:1/1////1 dhcp enabled vlan configure iphost ont ont:1/1////1 admin-state up configure voice ont voip-config ont:1/1////1 protocol sip conf-method omci configure voice ont sip-config ont:1/1////1 proxyserv-prof 20 outproxyserv-prof 20 reg-expire-time 3600 re-reg-head-start 360 aor-host-prt-prof 21 registrar-prof 24 uri-format sip-uri dscp 46 opt-tx-cntrl disable configure voice ont voice-sip-port 1/1////2/ user-aor user-name @telkom.net.id display-name password realm telkom.net.id ac-code-prof 2 app-serv-prof 8 ntwk-dp-prof 13 configure voice ont voice-port 1/1////2/ voipconfig sip voip-mediaprof 4 admin-state unlocked

b. Modify POTS Number configure voice ont pots 1/1////2/ admin-state locked configure voice ont voice-sip-port 1/1////2/ user-aor user-name @telkom.net.id display-name password realm telkom.net.id ac-code-prof 2 app-serv-prof 8 ntwk-dp-prof 13 configure voice ont pots 1/1////2/ admin-state unlocked

c. Delete configure voice ont pots 1/1////2/ admin-state locked configure voice ont voice-sip-port 1/1////2/ user-aor none user-name none display-name none password none realm telkom.net.id no ac-code-prof no app-serv-prof no ntwk-dp-prof configure voice ont voice-port 1/1////2/ voip-media-prof none configure bridge no port 1/1////voip configure qos interface 1/1////voip queue [0...3] shaper-profile none configure qos interface 1/1////voip upstream-queue 0 no bandwidth-profile

XGPON ALU 7360 ISAM Provisioning SOP

14

3.3 3.3.1

B-2404-P ONT TOPOLOGY Figure 9 Physical topology of E1 SFP to B-2404-P ONT at PT. Telkom Indonesia

Standard Operating Procedure

Connection FTM

B-2404-P ONT

PON E1 SFP

7360 ISAM FX OLT

3.3.2

Splitter Splitter 1:4 1:8

E1#1…4

CONNECTIONS AND COMPONENTS Figure 10 Physical connections for B-2404-P business ONTs

Table 5 B-2404-P business ONT connections Connection E1/T1 connections Ethernet connections PON optical connection Power connection

Function There are up to four E1/T1 ports supporting unstructured and fractional E1/T1 through RJ-48C connectors. Currently, E1 connections are supported while T1 connections are not. There are up to four Ethernet port supporting 10/100/1000Base-T Ethernet connections through Ethernet RJ-45 connectors. This connection is provided through an SC/APC connector for the physical interface to the PON. A terminal is provided to connect an external –12 V dc UPS to the ONT.

XGPON ALU 7360 ISAM Provisioning SOP

15

Standard Operating Procedure

Figure 11 B-2404-P business ONT LEDs

Table 6 B-2404-P business ONT LED descriptions Indicator

Color

Description

PWR

Green solid Green flashing slow Green flashing fast Red solid

Operating from AC power Operating from battery power System booting Battery low

GPON

Off Green solid Green flashing slow Red solid

Optical Not OK Optical OK; Ranged PON is in ranging and synchronizing process Optical Power Off (LOS/LOF)

DATA

Off Green solid Green flash

Ethernet service is not configured in ONT Ethernet service is configured in ONT Ethernet service is configured and there is activity of receiving or transmitting data

Off Green solid Green flashing

CES data path is not setup CES data path is ready LED blinks when links are up and there is activity (data receive and transfer). LED blinks with a 167 ms cycle and 50% duty cycle.

TIMING

Off Green solid Green flashing

Reference clock is not valid Reference clock ready In holdover state

UPDATE

Off Green flashing fast Red solid

Normal status Upgrading Upgrade failure

ALARM

Off Green solid Red solid

Normal status No alarm with local Ethernet access enabled (for Telnet) Indicates hardware failure

POTS

Off Green solid Green flashing fast

Telephone at POTS A and B are all in the on hook condition Telephone at POTS A and B are all in the off hook condition At least one POTS is in off hook condition for at least one hour

TEST

Off Green solid Green flashing fast

Normal status ONT is under loopback test ONT is in normal state with local Ethernet access (for Telnet) enabled

CES

XGPON ALU 7360 ISAM Provisioning SOP

16

3.3.3 CREATE/MODIFY/DELETE ONT a. Create configure equipment ont interface 1/1/// sw-ver-pland 3FE54603AOCI35 sernum subslocid WILDCARD voip-allowed enable cvlantrans-mode local configure equipment ont interface 1/1/// admin-state up configure equipment ont slot 1/1////5 planned-card-type e1 plndnumdataports 4 plndnumvoiceports 0 admin-state up

Standard Operating Procedure

b. Modify ONT S/N (Serial Number) configure equipment ont interface 1/1/// admin-state down configure equipment ont interface 1/1/// sernum configure equipment ont interface 1/1/// admin-state up

c. Delete configure equipment ont interface 1/1/// admin-state down configure equipment ont no interface 1/1///

3.3.4 CREATE/DELETE E1 SERVICE a. Create configure vlan id name:Default_TC0 configure service configure service configure service configure service configure service configure service configure service

mode cross-connect name in-qos-prof-name customer description vpls customer create vpls description vpls sap lt:1/1/: create vpls sap lt:1/1/15: create vpls user-user-com vpls no shutdown

///SFP configure ethernet line 1/1/15/ port-type uni admin-up configure ethernet line 1/1/15/ mau 1 type 1000baselxfd power up configure equipment sfpe1t1 clock lt: 1/1/15/ clocksource serdes configure equipment sfpe1t1 pwtdm lt: 1/1/15/: channel open packet-length 256 jitter-buff-size 7 vlanid priority 6 conseq-number 2 ecid-rx ecid-tx source-mac dest-mac configure equipment sfpe1t1 framer lt: 1/1/15/: frame-mode unframed configure equipment sfpe1t1 liu lt: 1/1/15/: distance longhaul cableimpedance 120ohms configure bridge port 1/1/15/ max-unicast-mac 10 configure bridge port 1/1/15/ vlan-id tag single-tagged // ONT configure interface port uni:1/1////5/ admin-up configure qos interface 1/1////5/ upstream-queue 0 bandwidth-profile name:E1 configure qos interface 1/1////5/ queue [0...3] shaper-profile name:E1 configure bridge port 1/1////5/ max-unicast-mac 10 configure bridge port 1/1////5/ vlan-id configure bridge port 1/1////5/ pvid configure ces ont profile profile-name jitter-buff-max 100 configure ces ont line 1/1////5/ mode unstructured frame unframed encoding hdb3 line-length 120ohms configure ces ont service 1/1////5/ service-nbr 1 vlan timing-mode adaptive maintenance-prof 2 payload-size 256 transmit-ckt-id expected-ckt-id dest-mac-address

b. Delete configure configure configure configure configure configure configure configure configure configure configure configure profile configure

bridge no port 1/1/15/ equipment sfpe1t1 no pwtdm lt:1/1/15/: equipment sfpe1t1 no clock lt:1/1/15/ ethernet line 1/1/15/ mau 1 power down ethernet line 1/1/15/ no admin-up ces ont no service 1/1////5/ ces ont line 1/1////5/ no admin-state ces ont no profile bridge no port 1/1////5/ interface port uni:1/1////5/ no admin-up qos interface 1/1////5/ queue [0...3] shaper-profile none qos interface 1/1////5/ upstream-queue 0 no bandwidthvlan no id

XGPON ALU 7360 ISAM Provisioning SOP

17

service service service service service service service

vpls shutdown vpls sap lt:1/1/: shutdown vpls no sap lt:1/1/: vpls sap lt:1/1/15: shutdown vpls no sap lt:1/1/15: no vpls no customer

Standard Operating Procedure

configure configure configure configure configure configure configure

XGPON ALU 7360 ISAM Provisioning SOP

18

3.4 3.4.1

POINT TO POINT (P2P) (NELT-B) TOPOLOGY

Standard Operating Procedure

Figure 12 Physical topology of P2P at PT. Telkom Indonesia

1 GbE SFP in NELT-B LT card

MSAN/SWITCH 7360 ISAM FX OLT

3.4.2

CONNECTIONS AND COMPONENTS Figure 13 Front view of the NELT-B

Figure 14 Board LEDS on the NELT-B

Table 7 LED Definition for the NELT-B LED

Color

Description

ALM

Red

Alert

A/S

Green

Active/Standby

PWR

Green

On line

XGPON ALU 7360 ISAM Provisioning SOP

19

Standard Operating Procedure

Figure 15 LEDs for SFP Ports

Table 8 Behavior of LEDs for SFP Ports Situation

Status LED

Board reset

Off

Link administrative down

Off

Link administrative up and Loss Of signal (LOS)

Off

Link administrative up and Signal detected

On

Link is OK and carrying traffic

Blinking

Figure 16 Physical of 1000Base-LX SFP

XGPON ALU 7360 ISAM Provisioning SOP

20

Table 9 Optical parameters for Alcatel-Lucent approved optical modules Part Number

Description

Wavelength

Reach

Operating Temperature

Optical Budget

Fiber mode

1310 nm

10 km

-40°C to + 85°C

11 dB

SMF

Gigabit Ethernet optical modules for optical connections 3FE 25774 AA

1 Gb/s Ethernet 1000Base-LX

Standard Operating Procedure

Table 10 1000Base-LX optical module parameters Parameter

Minimum

Typical

Maximum

Absolute Maximum Ratings Storage temperature

-40°C

-

+85°C

Operating case temperature(1)

-5°C

-

+85°C

Supply voltage

0V

-

+5.0V

-

1250 Mb/s

-

Optical output power(2)

-9.0 dBm

-

-3.0 dBm

TX wavelength

1260 nm

1310 nm

1360 nm

Center wavelength

1274 nm

1310 nm

1360 nm

Spectral width (-20dB)

-

-

4.0 nm

Extinction ratio

9 dB

-

-

Deterministic jitter

-

-

80 ps

Total jitter

-

-

227 ps

Relative intensity noise

-

-

-120 dB/Hz

Transmitter output eye

Compliant with IEEE 802.3z and FC-PI eye mask

Operating data rate Transmitter Performance Characteristics

Receiver Performance Characteristics Operating data rate(4)

-

1250 Mb/s

-

Input optical power (10-12 BER)(2)

-22.0 dBm

-

-3.0 dBm(5)

LOS thresholds, increasing light input

-

-

-22.0 dBm

LOS thresholds, decreasing light input

-30.0 dBm

-

-

LOS Hysteresis

0.5 dB

-

-

Deterministic jitter

-

-

170 ps

Total jitter

-

-

266 ps

Wavelength of operation

1100 nm

-

1600 nm

Optical return loss

12 dB

-

-

Electrical 3 dB upper cut-off frequency

-

-

1500 MHz

Electrical 3 dB upper cut-off frequency

Compliant with IEEE 802.3z standard

XGPON ALU 7360 ISAM Provisioning SOP

21

Standard Operating Procedure

3.4.3 CREATE/MODIFY/DELETE TAGGED VLAN SERVICE a. Create configure vlan id mode cross-connect name in-qos-prof-name name:Default_TC0 configure service customer description configure service vpls customer create configure service vpls description configure service vpls sap lag-1: create configure service vpls sap lt:1/1/16: create configure service vpls no shutdown configure interface port ethernet-line:1/1/16/ admin-up configure ethernet line 1/1/16/ port-type uni admin-up configure ethernet line 1/1/16/ mau 1 type 1000baselx10 speed-auto-sense power up configure bridge port 1/1/16/ max-unicast-mac 10 configure bridge port 1/1/16/ vlan-id tag single-tagged

b. Delete configure configure configure configure configure configure configure configure configure configure configure configure

bridge no port 1/1/16/ ethernet line 1/1/16/ mau 1 no speed-auto-sense power down ethernet line 1/1/16/ no admin-up interface port ethernet-line:1/1/16/ no admin-up service vpls shutdown service vpls sap lag-1: shutdown service vpls no sap lag-1: service vpls sap lt:1/1/16: shutdown service vpls no sap lt:1/1/16: service no vpls service no customer vlan no id

XGPON ALU 7360 ISAM Provisioning SOP

22

4.

APPENDIX: PROVISIONING FLOW Figure 17 Create ONT flow

Standard Operating Procedure

1. CREATE EQUIPMENT ONT INTERFACE 2. UNLOCK EQUIPMENT ONT INTERFACE 3. CREATE EQUIPMENT ONT SLOT

Figure 18 Modify ONT serial number flow 1. LOCK EQUIPMENT ONT INTERFACE 2. MODIFY EQUIPMENT ONT INTERFACE 2. UNLOCK EQUIPMENT ONT INTERFACE

Figure 19 Delete ONT flow 1. LOCK EQUIPMENT ONT INTERFACE 2. DELETE EQUIPMENT ONT INTERFACE

Figure 20 Create internet service flow (PPPoE) 1. SET UPSTREAM QOS INTERFACE 2. SET DOWNSTREAM QOS INTERFACE 3. UNLOCK INTERFACE PORT 4. CREATE BRIDGE PORT VLAN TRANS 881 5. SET PPPOE USERNAME 6. SET PPPOE PASSWORD

XGPON ALU 7360 ISAM Provisioning SOP

23

Figure 21 Modify service bandwidth flow 1. MODIFY UPSTREAM QOS INTERFACE

Standard Operating Procedure

2. MODIFY DOWNSTREAM QOS INTERFACE

Figure 22 Modify internet PPPoE username and password flow 1. MODIFY PPPOE USERNAME 2. MODIFY PPPOE PASSWORD

Figure 23 Delete internet service flow (PPPoE) 1. DELETE PPPOE PASSWORD 2. DELETE PPPOE USERNAME 3. DELETE BRIDGE PORT 4. LOCK INTERFACE PORT 5. DELETE DOWNSTREAM QOS INTERFACE 6. DELETE UPSTREAM QOS INTERFACE

Figure 24 Create internet service flow (Bridge) 1. SET UPSTREAM QOS INTERFACE 2. SET DOWNSTREAM QOS INTERFACE 3. UNLOCK INTERFACE PORT 4. CREATE BRIDGE PORT UNTAGGED VLAN

XGPON ALU 7360 ISAM Provisioning SOP

24

Figure 25 Delete internet service flow (Bridge) 1. DELETE BRIDGE PORT

Standard Operating Procedure

2. LOCK INTERFACE PORT 3. DELETE DOWNSTREM QOS INTERFACE 4. DELETE UPSTREAM QOS INTERFACE

Figure 26 Create IPTV service flow 1. SET UPSTREAM QOS INTERFACE 2. SET DOWNSTREAM QOS INTERFACE 3. UNLOCK INTERFACE PORT 4. CREATE BRIDGE PORT UNTAGGED VLAN 5. CREATE IGMP CHANNEL

Figure 27 Delete IPTV service flow 1. DELETE BRIDGE PORT 2. LOCK INTERFACE PORT 3. DELETE DOWNSTREAM QOS INTERFACE 4. DELETE UPSTREAM QOS INTERFACE

XGPON ALU 7360 ISAM Provisioning SOP

25

Figure 28 Create voice service flow 1. SET UPSTREAM QOS INTERFACE

Standard Operating Procedure

2. SET DOWNSTREAM QOS INTERFACE 3. CREATE BRIDGE PORT UNTAGGED VLAN 4. CREATE IPHOST 5. CREATE VOICE ONT VOIP-CONFIG 6. CREATE VOICE ONT SIP-CONFIG 7. CREATE VOICE ONT VOICE-SIP-PORT 8. CREATE VOICE ONT VOICE-PORT & UNLOCK

Figure 29 Modify POTS port flow 1. LOCK VOICE ONT POTS 2. MODIFY VOICE ONT VOICE-SIP-PORT 3. UNLOCK VOICE ONT POTS

Figure 30 Delete voice service flow 1. LOCK VOICE ONT POTS 2. MODIFY VOICE ONT VOICE-SIP-PORT 3. MODIFY VOICE-ONT VOICE-PORT 4. DELETE BRIDGE PORT 5. DELETE UPSTREAM QOS INTERFACE 6. DELETE DOWNSTREAM QOS INTERFACE

XGPON ALU 7360 ISAM Provisioning SOP

26

Figure 31 Create E1 service flow 1. CREATE IACM VLAN

Standard Operating Procedure

2. CREATE SERVICE CUSTOMER 3. CREATE SERVICE VPLS 4. UNLOCK INTERFACE PORT ETHERNET-LINE 5. SET ETHERNET-LINE MAU TYPE AND UNLOCK 6. CREATE SFPE1T1 CLOCK 7. CREATE SFPE1T1 PWTDM 8. CREATE SFPE1T1 FRAMER 9. CREATE SFPE1T1 LIU 10. CREATE BRIDGE PORT ON SFP E1 IN NELT-B CARD 11. UNLOCK INTERFACE PORT ON ONT 12. SET UPSTREAM QOS INTERFACE 13. SET DOWNSTREAM QOS INTERFACE 14. CREATE BRIDGE PORT UNTAGGED VLAN 15. CREATE CES ONT PROFILE 16. CREATE CES ONT LINE 11. CREATE CES ONT SERVICE

XGPON ALU 7360 ISAM Provisioning SOP

27

Figure 32 Delete E1 service flow 1. DELETE BRIDGE PORT

Standard Operating Procedure

2. DELETE EQUIPMENT SFPE1T1 PWTDM 3. DELETE EQUIPMENT SFPE1T1 CLOCK 4. REMOVE ETHERNET LINE MAU TYPE AND LOCK 5. DELETE CES ONT SERVICE 6. DELETE CES ONT LINE 7. DELETE CES ONT PROFILE 8. DELETE ONT BRIDGE PORT 9. LOCK ONT INTERFACE PORT 10. DELETE DOWNSTREAM QOS INTERFACE 11. DELETE UPSTREAM QOS INTERFACE 12. DELETE IACM VLAN 13. DELETE SERVICE VPLS 14. DELETE SERVICE CUSTOMER

XGPON ALU 7360 ISAM Provisioning SOP

28

Figure 33 Create point to point tagged vlan flow 1. CREATE IACM VLAN

Standard Operating Procedure

2. CREATE SERVICE CUSTOMER 3. CREATE SERVICE VPLS 4. UNLOCK INTERFACE PORT ETHERNET-LINE 5. SET ETHERNET-LINE MAU TYPE AND UNLOCK 6. CREATE BRIDGE PORT TAGGED VLAN

Figure 34 Delete point to point tagged vlan flow 1. DELETE BRIDGE PORT 2. REMOVE ETHERNET-LINE MAU TYPE AND LOCK 3. LOCK INTERFACE PORT ETHERNET-LINE 4. DELETE SERVICE VPLS 5. DELETE SERVICE CUSTOMER 6. DELETE IACM VLAN

XGPON ALU 7360 ISAM Provisioning SOP

29