Snp Catalog

   0  .    3    R    b   e    F    4    1    0    2

Site Installation Products

Global Installation P roducts Introduction;  The intended readers of this catalogue are Product management, Supply management, Key account management, Design organisation and personal at the market units within Ericsson companies and their customers.

Catalogue Index Mechanica l Support for Equipment ............... .................. ................... ................. .................. ................... . .................. .................. ......3-16 Cable Routing ............. ............. ............... .............. .............. .............. .................. .............. .............. ................. ................ ................1 7-25 Grounding and surge protecti on ............... .............. .............. .............. .................. .............. .............. ................. ............... ...............26 -34 Cables ..................................................................................................................................................................................................35 Cable

Clamps..................................................................................................................................................................................36-37

Cable Sealing............. Sealing.......................... ........................ ....................... ........................ ......................... ........................ .................... ................... ...................... ....................... ...................... .................... ................... .................... .................. ...........38-41 ...38-41

 The catalogue shall also be seen as ma rket material to be presented by Ericsson to customers. Products are present in the  V ariant ariant Configuration (VC) and in the Ericsson Configuration Portfolio (ECP).

Cabinets and frames ............. .............. .............. ............... .............. ................ ................... ............... .............. ................. ................ .42-44 Tools

and

instruments.......................................................................................................................................................................45-54

Accessories

......................................................................................................................................................................................55-58

Power

Back-up

................................................................................................................................................................................59-64

Site installation products are also available in Site Web Shop, where you can find and evaluate products presented with images, technical- and commercial information. General quality and durability of the p roducts;  All products in the portfolio are selected and handpicked among leading manufacturers or specially produced with the aim to secure a long lasting durability of the installation, the function of the network and consequently saving cost for the operator avoiding revisits to the site. Installation management;  The catalogue displays the products as stand alone units but they are a part of an optimised installation system described in the Standard Module Overview (SMO) that should be consulted for the full context. Ordering management;  The catalogue includes a variety of t imesaving pre-assembled kit’s that includes all materials to install a function in one order line. All ordering are handled by Ericsson using the product numbers in the catalogue.

1

Catalogue Index

Mechanical Support for Equipment

Mounting Brackets

Mountin g Bracket s................ ................... ................. ................... ................. .................. ................ .................. ............... 3-14 Tubes..................... Tubes.......... ....................... ......................... ........................ ....................... ......................... ......................... ........................ ....................... ........................ .............................. ............................. ....................... .................14 ......14 Freestanding ........... ..................... ..................... ..................... .................... .................... ....................... ...................... .................. .................... ....................... ....................... ..................... .................... ......................15,16 ............15,16 Cable Runs........... Runs....................... ....................... ....................... ........................ ......................... ........................ ........................ ........................ ............................. .............................. ........................ ....................... ............. .. 17-22 Cable Suspens ion Support....... .................. .................. .................. .................. .................. ............... ................. .......... 22

- 24

Cable Support Kit (Hoisting Grip).............. Grip).......................... ........................ ........................ ........................ ...................... .................... ........................... ............................. ........................ ..................... ......... 25 Grounding Cables .............. .............. ............... .............. ............. ............. .............. ............. ................ .............. .......... 26-30 Grounding Bars and Rods (combined )................. .................. .................. .................. .................. ............... ................. 31, 32 Grounding Joint Clamps....... Clamps................... ........................ ........................ ........................ ......................... ..................... .................... ........................ ............................. ............................. ........................ ................. ..... 32 Grounding Cable Lugs ............ ....................... ....................... ........................ ......................... ......................... ........................ ....................... ............................ ............................. ........................ ........................ ............ 33 Surge Protection........ Protection..................... ......................... ........................ ........................ ......................... .................... .................... ......................... .............................. .............................. ..................... .....................33, ............33, 34 Surge Arrestor ............ ......................... ........................ ....................... ........................ ......................... ............................. ............................ ......................... ........................ ....................... ........................ ........................ ............ 34 Coaxial Cables ............ ........................ ..................... ..................... ........................ ........................ ........................ ........................ ........................ ............................. ............................. ........................ ....................... ..............35 ...35 Accessories ........... ....................... ........................ ........................ ........................ ........................ ........................ ........................ ........................ .............................. ............................. ....................... ........................ .................35 .....35 Feeder clamps.......... clamps...................... ......................... ......................... ....................... ....................... ......................... ......................... ....................... ............................. .......................... ....................... .......................... .............. ... 36 Fiber and Power Clamps............................. ........................... .................. .................. .................. ................. .................. ................... .................. ................... ................... ..................... ................. .....

.... ........ 37

Hybrid Clamps............ Clamps.......................... ......................... ....................... ........................ ......................... ........................ ....................... ........................ ............................ ............................ ........................ ........................ ............ 37 Multi Diameter Clamp...... Clamp.................. ......................... ......................... ........................ ........................ ...................... .................... ...................... ....................... ............................ ............................. ....................... ........... 37 Cable Sealing Kits .............. .............. ............... .............. ............. ............... .............. ............... .............. .............. ........ 38-41 Frames .......... ...................... ........................ ........................ ......................... ......................... ........................ ............................. ............................. ........................ ........................ ........................ ........................ ........................42 ............42 Cabinet and Frame Accessories .......... ..................... .................. .................. ...................... ..................... ..................... ....................... ....................... ...................... ...................... ..................... ............ .. 43,44 Optical Cable Boxes............. Boxes.......................... ......................... ....................... ....................... ......................... ......................... ....................... .......................... .......................... ....................... ........................ ................. ..... 44 Power Cable Boxes............. Boxes......................... ........................ ........................ ........................ ............................ ............................ ........................ .................................. .................................. ........................ .................. ...... 44 Feeder Tools ............ ........................ ........................ ......................... ........................ ....................... ......................... ......................... ....................... ............................ ............................. ........................ ....................... .............. ... 45 Electricall Power Tools........... Electrica Tools....................... ........................ ......................... ......................... ....................... ....................... ........................ ............................. ............................. ........................ ........................ .............. 46 Torque Wrenches................. Wrenches............................. ........................ ........................ ........................ ......................... ........................ ....................... ............................. ............................. ........................ ....................... .............. ... 47 Crimping tools ........... ....................... ........................ ........................ ..................... ..................... ........................ ........................ ........................ ............................. ............................. ........................ ........................ ................ .... 48 Tool Kits .............. .............. ................. .............. ............... ........... .............. ............. .............. .............. .............. ........... 49, 50 Safety Equipmen t ............. ............. ............... .............. ............. ................ .............. ............ ............... ............... ............ 50-52 Special Tools.............. Tools........................... ........................ ....................... ........................ ..................... ..................... ...................... ...................................... ........................................ ........................ ........................ ..................52 ......52

Mounting Brackets Single RRU Support The support kit holds one Radio Remote Units of type RRUW, RRUS 01 or RRUS11. This support can be installed on wide range of vertical structures in telecom mast and towers.

Tools for Optical Fiber .......... ..................... ..................... ..................... ..................... ..................... ...................... ..................... ..................... ...................... ...................... ................... .................. ................... ......... 53, 54

Excellent corrosion resistance due to acid proof stainless steel fasteners and aluminium clamp. CLAMP MOUNTING RANGE: TUBES: Square Profile: 90˚ Angle Profile: 60˚ Angle Profile Minimum: (mm) Ø25 35 x 35 35 x 35 40 mm opening Maximum: (mm) Ø120 90 x 90 90 x 90 100 mm opening

DDF Tools ............ ....................... ....................... ...................... ...................... ....................... ........................ ......................... ........................ ....................... ............................. .............................. ........................ .....................54 .........54

Consist of:

Test Instruments ........... ....................... ........................ ........................ ....................... ........................ ......................... ........................ ....................... ............................ ............................. ........................ ...................... .......... 53

Marking........................ Marking............ ........................ ....................... ........................ ........................ ........................ ......................... ........................ ............................. ............................ ....................... ........................ .................. ...... 55,56 Miscellaneous Accessories .......... .................... .................... .................... ..................... ........................ ....................... ..................... ...................... ...................... ..................... ....................... ................... ...... 57,58 Battery Sets... ................. ......................... ................................. ........................... .......................... ................. ................ 59-61 Battery accessories .......... .................... ..................... .................... .................... ...................... ..................... ..................... ..................... .................... ...................... ...................... .................... ..................... ..............61-64 ...61-64

2

Qty 1 1 2 6 4 4 2 4 8 4

Description Clamp profile, front Clamp profile, back RRU attachment Nut, M10 Washer,BRB M10 Nut low, M12 Bolt, M10x200H Bolt, M12x35H Washer,BRB M12 Lock nut,LM M12

Pr od od uc t Nu mb mb er

L en eng th

SXK 107 2840/ 1

290 mm

 

Width

100 mm

 

H e ig ht

W ei ei gh gh t

100 mm

2.106 kg

3

Mechanical Support for Equipment

Mechanical Support for Equipment

Mounting Brackets

Mounting Brackets

Double RRU Support

Single RRU with PSU Support kit

The support kit holds up to two Radio Remote Units of type RRUW, RRUS 01 or RRUS11. It can be installed on wide range of vertical structures in telecom mast and towers. Excellent corrosion resistance due to acid proof stainless steel fasteners and aluminium clamp.

The support kit holds one Radio Remote Units of type RRUS 02, RRUS 12 or one Radio Base Station RBS 6302. It has space for one PSU on the backside of the RRU. It can be installed on a wide range of vertical structures in telecom mast and towers. Excellent corrosion resistance due to acid proof stainless steel fasteners and aluminium clamp.

CLAMP MOUNTING RANGE: TUBES: Minimum: (mm) Ø25 Maximum: (mm) Ø120

Square Profile : 35 x 35 90 x 90

90 ˚ Angle Profile 35 x 35 90 x 90

60 ˚ Angle Profile 40 mm opening 100 mm opening1

Max allowed Net Wind Area (@ Windspeed 50m/s): 0.6 m²

Length 295 mm

Width 100 mm

Height 100 mm

Weight 2.86 kg

Triple RRU Support The support kit holds up to three Radio Remote Units of type RRUW, RRUS 01 or RRUS11. It can be installed on wide range of vertical structures in telecom mast and towers. Excellent corrosion resistance due to acid proof stainless steel fasteners and aluminium clamp. CLAMP MOUNTING RANGE: TUBES: Minimum: (mm) Ø25 Maximum: (mm) Ø120

Square Profile : 35 x 35 90 x 90

90 ˚ Angle Profile 35 x 35 90 x 90

60 ˚ Angle Profile 40 mm opening 100 mm opening1

Max allowed Net Wind Area (@ Windspeed 50m/s): 0.9 m²

Consist of: Qty Description 1 Clamp profile, front 1 Clamp profile, back 2 RRU attachme nt 1 Angle Bracket Kit 2 Angle Bracket 4 Bolt, M10x30H 4 Washer,BRB M10 2 Bolt, M10x200H 6 Nut, M10 4 Washer,BRB M10 4 Nut low, M12 4 Bolt, M12x35H 8 Washer,BRB M12 4 Lock nut,LM M12 Product Number SXK 107 2840/2

Length 370 mm

W idth 100 mm

Height 100 mm

Wei ght 3 kg

Double RRU with PSU Support kit The support kit holds up to two Radio Remote Units of type RRUS 02, RRUS 12 or Radio Base Station RBS 6302. It can be installed on a wide range of vertical structures in telecom mast and towers. It has space for one PSU´s on the backside of each RRU (max 2 PSU´s). Excellent corrosion resistance due to acid proof stainless steel fasteners and aluminium clamp.

CLAMP MOUNTING RANGE: TUBES: Minimum: (mm) Ø25 Maximum: (mm) Ø120

Length 515 mm

Width 350 mm

Height 280 mm

Weight 11.7 kg

Square Profile : 35 x 35 90 x 90

90 ˚ Angle Profile 60 ˚ Angle Profile 35 x 35 40 mm opening 90 x 90 100 mm opening

Consist of: Qty Description 1 Clamp profile, front 1 Clamp profile, back 4 RRU attachme nt 2 Angle Bracket Kit 2 Angle Bracket 4 Bolt, M10x30H 4 Washer,BRB M10 2 Bolt, M10x200H 6 Nut, M10 4 Washer,BRB M10 8 Nut low, M12 8 Bolt, M12x35H 16 Washer,BRB M12 8 Lock nut,LM M12 Product Number SXK 107 2841/2

4

90 ˚ Angle Profile 60 ˚ Angle Profile 35 x 35 40 mm opening 90 x 90 100 mm opening

Max allowed Net Wind Area (@ Windspeed 50m/s): 0.6 m²

Consist of: Qty Description 1 RRU Triple support plate, 1 Double back profile 1 Back profile, small clamp 4 Jaw, small clamp 4 Spring 4 Locking spring 10 Nut, M12 30 Washer,BRB M12 2 Washer,BRBS M12 2 Bolt, M12x245 2 Bolt, M12x400 12 Nut low, M12 12 Lock nut,LM M12 12 Bolt, M12x35H Product Number SXK 107 2842/1

Square Profile : 35 x 35 90 x 90

Max allowed Net Wind Area (@ Windspeed 50m/s): 0.6 m²

Consist of: Qty Description 1 Clamp profile, front 1 Clamp profile, back 4 RRU attachme nt 6 Nut, M10 4 Washer,BRB M10 8 Nut low, M12 2 Bolt, M10x200H 8 Bolt, M12x35H 16 Washer,BRB M12 8 Lock nut,LM M12 Product Number SXK 107 2841/1

CLAMP MOUNTING RANGE: TUBES: Minimum: (mm) Ø25 Maximum: (mm) Ø120

Length 300 mm

W idth 210 mm

Height 100 mm

Wei ght 5 kg

5

Mechanical Support for Equipment

Mechanical Support for Equipment

Mounting Brackets

Mounting Brackets

Triple RRU Support with PSU kit

Single RRUS Support Kit With PSU/A2/TSBDA 

The support kit holds up to three Radio Remote Units of type RRUS 02, RRUS 12 or Radio Base Station RBS 6302. It can be installed on a wide range of vertical structures in telecom mast and towers. It has space for one PSU´s on the backside of each RRU (max 3 PSU´s. Excellent corrosion resistance due to acid proof stainless steel fasteners and aluminium clamp.

Install one RRU or one TSBDA units perpendicular to the mounting tube with additional units such as A2 or PSU with this kit. The RRU support can handle a wide range of all common frame leg designs, round, square, angle etc. The grooves in the attachment beam on the back of the clamp allows the installed unit/units to always be centered around the frame leg. All components are made of anodized aluminum and stainless steel which gives the support excellent corrosion resistance.

Max allowed Net Wind Area (@ Windspeed 50m/s): 0.9 m² CLAMP MOUNTING RANGE: TUBES: Minimum: (mm) Ø25 Maximum: (mm) Ø120

Square Profile: 35 x 35 90 x 90

90° Angle Profile 60° Angle Profile 35 x 35 40 mm opening 90 x 90 100 mm opening

Consist of: Qty Description 1 RRU Triple support plate 3 Angle Bracket Kit 2 Angle Bracket 4 Bolt, M10x30H 4 Washer,BRB M10 1 Double back profile 1 Back profile, small clamp 4 Jaw, small clamp 4 Spring 4 Locking spring 10 Nut, M12 30 Washer, BRB M12 2 Washer, BRBS M12 2 Bolt, M12x245 2 Bolt, M12x400 12 Nut low, M12 12 Lock nut, LM M12 12 Bolt, M12x35H Product Number SXK 107 2842/2

Max net wind Area at 180 Km/h (50m/s): 0,6 m2 Clamp mounting range: Frame leg/form Min (mm) Tubes Diameter 25 Square profile 35x35 90 Deg. Angle 35x35 60 Deg Angle(opening) 40

Max (mm) (with 200mm bolts) 120 90x90 90x90 100

Consist of: Qty Description 2 Clamp profile front 2 Clamp profile,Back 2 Attachment beam 2 Support arm 1 Attachment angle 1 Attachment arm 2 Countersuncscrew , M8x30 12 Nut, M10 12 Washer M10 4 Lock nut M10 4 Bolt, M10x130H 8 Bolt, M10x30H

Length 515 mm

Width 350 mm

Height 280 mm

W ei ght 14.1 kg

Product Number SXK 107 2839/1

Length 530 mm

Wi dth 95 mm

Height 85 mm

Weight 5 kg

Expansion Kit For Dual RRUS support RRU Wall Support  A light weighted support for installation of one RRU or one RBS 6302 towards the wall. The support can fit all common Ericsson RRU models such as RRUW,RRUS 01, RRUS 11, RRUS 02 and RRUS 12. It is also possible to attach a PSU or an A2 on the backside of the RRU.  All components are made of anodized aluminum and stainless steel which gives the support excellent corrosion resistance. Max allowed antenna net wind area at wind speed: 150 km/h (42m/s): 1.4 m² 200 km/h (55m/s): 0.8 m² Consist of: Qty Description 2 RRU Wall bracket 2 Attachment arm 360 4 Bolt, M10x30H 4 Washer M10 4 Bolt, M8x35H 4 Lock nut M8 8 Washer M8 Product Number

SXK 107 2848/1

Length 370 mm

Width 80 mm

Height

W ei ght

80 mm

2.5 kg

Install two RRU or TSBDA units perpendicular to the mounting tube with additional units such as A2 or PSU. The RRU support can handle a wide range of all common frame leg designs, round, square, angle etc. The grooves in the attachment beam on the back of the clamp allows the installed unit/units to always be centered around the frame leg. All components are made of anodized aluminum and stainless steel which gives the support excellent corrosion resistance. Max net wind Area at 180 Km/h (50m/s): 0,6 m² Clamp mounting range: Frame leg/form Tubes Diameter Square profile 90 Deg. Angle 60 Deg Angle(opening)

Min (mm) 25 35x35 35x35 40

Max (mm) (with 200mm bolts) 120 90x90 90x90 100

Consist of: Qty Description 2 Support arm 1 Attachment angle 1 Attachment arm 2 Countersuncscrew , M8x30 4 Lock nut M10 8 Washer M10 8 Bolt, M10x30H Product Number SXK 107 2839/2

Length 370 mm

Wi dth 80 mm

Height 80 mm

Weight 2 kg

 Angle Bracket for RRUS RRUS With this Angle bracket it is posible to attach one PSU on the backside of RRUS 01, RRUS 02, RRUS 11 or RRUS RRUS 12. Consist of: Qty Description 2 Angle Bracket 4 M10 Washer 4 M10x30Bolt Product Number NTM 201 4128/1

6

Length 190 mm

Wi dth 90 mm

Height 60 mm

Weight 0.865 kg

7

Mechanical Support for Equipment

Mechanical Support for Equipment

MountingB Mounting B rackets

Mounting Brackets

Single RRU Support

Link Support, 1-Leg

TheÊsingl eÊRRUÊsupport isÊdesign edÊtoÊcarr yÊaÊsing leÊRRUÊatt ache dÊtoÊaÊstru ctur alÊlegÊmeme ber.

Clam pÊkitÊinÊtwoÊlevel s,ÊwithÊspac eÊfor one moun ting tube (mo unti ngÊtubeÊnot inc lude dÊinÊtheÊkit) . Typi cal forÊinsta lla tio nÊofÊlargeÊ(diam .Ê2,6m )Êradi oÊlin ks,ÊorÊsev eral smal lÊones orÊotherÊcommon tel eco mÊequi pmen t.T heÊ1-legÊlinkÊsupp ortÊcanÊbeÊinstal ledÊonÊmas tÊleg (mi n.25 -max .270 mm) asÊwellÊas conical towersÊ(min.60x 60mm,Êmax.Ê200x200mm).

TheÊsuppor tÊcanÊbeÊused onÊaÊrang eÊofÊpoleÊdia mete rsÊandÊwith orÊwithout aÊPSUÊatt ache dÊtoÊtheÊback side ofÊtheÊ RRU.ÊItÊcanÊalsoÊbeÊmoun tedÊonÊangl eÊiron sÊasÊwellÊasÊboxÊsec tion alÊbeams Consist of: Qty Des cri pti on 2ÊÊ Si ng le RR RRUÊcl UÊcla mp 2ÊÊÊÊ ÊÊ RR UÊcl c lamp 4ÊÊÊÊ ÊÊÊBol tÊM1 0, ÊA4 ÊÊ 4ÊÊ Th re ad ed ro dÊM10 ,ÊHDG 16 ÊÊ ÊÊWa ÊÊ Wash sh er BR BRB, B, HD HDG G 20 ÊÊ ÊÊ ÊÊ Nu tÊM1 0, ÊHDG Nu

CLAMPÊMOUNTIN GÊRANGE Mi ni mu m: [m m] Ê Ma xi mu m: [m m] Ê

Tu be sÊÊ 25 11 4ÊÊ

Sq ua re Pr Prof of il eÊÊ 90 an gl eÊÊÊ 60 an gl eÊ 35 x3 x35ÊÊ 5ÊÊ 35 x3 5ÊÊ 40 mm wi dt hÊofÊop hÊofÊopen en in g. 80 x8 x80ÊÊ 0ÊÊ 80 x8 0ÊÊ 10 0ÊmmÊwid th of op en in g.

Cla mpÊprof il esÊÊ S35 5MC FZV Nut sÊandÊbolt sÊÊ 8.8 FZV orÊequi val en t Product Number SXKÊ107Ê2869/1

Length 250Êmm

Width 130Êmm

Height 70ÊmmÊ

W ei eight 4,3kg

Cable Ladder RRU Support TheÊRRUÊsupp ortÊisÊdesi gned forÊattac hing RRUÕsÊtoÊexisti ngÊcableÊladder s. TheÊsuppor tÊisÊdeliv ered asÊaÊfla tÊpac kÊandÊcanÊeas ily beÊmounted onÊcableÊtraysÊofÊwidt hÊ300- 500m m Consist of: Qty De scr ip ti on 1ÊÊ RR RRUÊcab UÊcab le tr ay ho ld er sh ee tÊL 1ÊÊ RR RRUÊcab UÊcab le tr ay ho ld er sh ee tÊR 8ÊÊ Se lf ta pp in gÊscr ew

Product Number S XK Ê 1 07 07 Ê 2 83 83 2/ 2/ 1

HoleÊpattern

Product Number SXKÊ107Ê2867/1

Width 3 20 20 Ê mm

Height 2 30 30 Ê mm

Weight 2 3k 3k g

Wall supp ortÊkitÊinÊtwoÊlev els with spa ceÊforÊoneÊmounti ngÊtubeÊ(mou ntin gÊtube notÊinclu dedÊinÊtheÊkit). Typi cal forÊinsta lla tio nÊofÊpanelÊantenn as, radi oÊlink sÊorÊotherÊcommon tel eco mÊequi pmen t.ÊTheÊLig htÊwallÊsupp ort canÊhandleÊmountingÊtubesÊ65mm-90mm. Consist of: Qty Des cri pti on 2ÊÊÊÊ ÊÊHo l de rÊpa rt ÊÊ 2ÊÊ Tu be cl am pÊpar t 8ÊÊÊÊ ÊÊWa sh er ÊBRB ÊÊ ÊBRBÊM12 ÊM12 2ÊÊ U- bo lt ,Ê60m m- 90 mm 4ÊÊÊÊ ÊÊLo ck Ênut ,ÊLM ÊM12 ÊÊ 8ÊÊÊÊ ÊNut utÊM12 12 4ÊÊ Bo lt M1 2x 40 40H H

S355MCÊ S35 5MCÊ F ZV FZV A4-70ÊorÊequival ent Length 450ÊmmÊ

Length 4 00 00 Ê mm

Wall Support, Light

MECHANICALÊSPECIFICATION DIMENSIONS Length Len gth(mm (mm)Ê )Ê 325 32 5 Wi dt dt h( h ( mm mm ) 3 00 -5 -5 00 H ei ei gh gh t( t ( mm mm ) 2 88 Sl op ope Ê ( )Ê 17, 5 MATERIAL SteelÊ Stee lÊplate platesÊ sÊ BoltsÊandÊnutsÊ

Consist of: Qty Des cri pti on 1ÊÊÊÊ ÊCla l amp 1ÊÊ Cl amp do ubl eÊback pro fi le 4ÊÊÊÊ ÊÊBo l tÊM1 ÊÊ tÊM12x 2x 40 0 8ÊÊ Ja w, sm al lÊclam cl am p 4ÊÊÊÊ ÊÊWa sh er ÊBRB ÊÊ ÊBRBÊM12 ÊM12 2ÊÊ Bac kpr of il e,Êsma ll cl am p 4ÊÊ Do ub le ba ck pr prof of il e 2ÊÊ Do ub le ba ck pr prof of il e 8ÊÊ Lo ck in gÊspr in g 8ÊÊÊÊ ÊSpr pri ng 8ÊÊÊÊ ÊSpr pri ng 12 ÊÊ ÊÊNu t, ÊM12 ÊÊ 12 ÊÊ ÊÊNu tÊM1 2 ÊÊ 4ÊÊ La rg eÊwas he r, BR BRBS BS M1 M12 2 4ÊÊ La rg eÊwas he rÊBRBS M1 2 8ÊÊ Lo ck in gÊspr in g 8ÊÊ Ja w, la rg eÊcla mp 4ÊÊ Bo lt ,ÊM12 x2 x245 45 2ÊÊ Up pe rÊpla te 10 0x 10 10x2 x2 25 4ÊÊÊÊ ÊÊWa sh er ÊBRB ÊÊ ÊBRBÊM12 ÊM12 2ÊÊ Lo we rÊpla te 80 x1 0x 17 5 16 Wa sh er BR BRBÊM12 BÊM12 16 ÊÊ ÊÊNu t, ÊM12 ÊÊ 8ÊÊ Bo lt ,ÊM12 x4 x425 25

Width 350Êmm

Height 10Êmm

W ei eight 3Êkg

Product Number S XK Ê 1 07 07 Ê 2 83 83 3/ 3/ 1

Length 2 85 85 Ê mm

Width 1 90 90 Ê mm

Height 1 50 50 Ê mm

Weight 4 .5 .5 Ê kg

Universal Antenna Support Univ ersa lÊcla mpÊkitÊinÊtwoÊlev els with spac eÊfor one moun ting tube (the uppe rÊcla mpÊcanÊbeÊadjuste dÊtoÊtiltÊtheÊantenn aÊincl ina tio n).ÊTypic alÊforÊinst all ati onÊofÊpane lÊante nnas ,Êradi oÊlin ksÊorÊothe rÊcomm onÊteleco mÊequi pmen tÊsuch asÊmainÊremo teÊunits,ÊpowerÊunits, TMA, fil ters etc. Clam pÊmoun ting rang e:ÊTubes,Êmin.d iam. 25mm -ÊmaxÊ210mm diam.ÊTowerÊlegsÊsquareÊprofiles:ÊMin.25x25mm -Max.150x150 mm.  AngleÊprofile:ÊMin.35x35mm-Max.150x150mm.Ê(MountingÊtubeÊnotÊincluded). Consist of: Qty De scr ipt io n 2ÊÊÊÊ 2ÊÊ ÊÊÊHol de rÊpa rt 28 ÊÊÊNut ,ÊM1 2 2ÊÊ Co un te rÊsup po rt pa rt 4ÊÊ Th re ad ed ro dÊHGS dÊHGS,ÊM12 ,ÊM12 2ÊÊ Tu be cl am pÊpar t 6ÊÊÊÊ 6ÊÊ ÊÊÊLoc kÊnu t, LM ,ÊM1 2 2ÊÊÊÊ 2ÊÊ ÊÊÊTil tÊar mÊpa rt 6ÊÊ Bo lt ,ÊM12 x4 0H 20 Wa sh er BR BRBÊM12 BÊM12 2ÊÊ U-b ol t, dia m.6 0mm -di am. 90m m Product Number S XK Ê 1 07 07 Ê 2 12 12 6/ 6/ 1

8

Length 2 90 90 Ê mm

Width 1 90 Ê mm

Height 1 50 Ê mm

W ei eight 8Ê kg

9

Mechanical Support for Equipment

Mechanical Support for Equipment

Mounting Brackets

Mounting Brackets

Parallel Bracket Kit

Top Spire Support

Bracket extension kit for two levels.Typical for extension of existing mounting tubes or as a support for panel antennas, small radio links or other common telecom equipment. The bracket can handle mounting tubes and frame legs 60mm-90mm. Note: mounting tube not included.

 An extension kit for towers and masts with space for three mounting tubes. Typical for installations of panel anantennas up to 2,3m. Clamp mounting range for tubes 25mm-120mm, for square profiles 30x30mm- 90x90mm

Consist of: Qty Description 16 Nut M12 8 Washer BRB M12 4 U-Bolt, 60mm-90mm 2 Z profile 8 Lock nut, LM M12 Product Number SXK 107 2834/1

Length 250 mm

Width 130 mm

Height 110 mm

W eight 2.5 kg

Double Antenna Support Clamp kit in two levels, with horizontal beams and space for two mounting tubes (mounting tubes not included in the kit). Typical for installation of panel antennas, radio links or other common telecom equipment. Clamp mounting range: Tubes; Min.25mm-Max.120mm, squaare profiles; Min.30x30mm-Max.90x90mm. Min.30x30mm-Max.90x90mm. Consist of: Qty Description 1 Cue Dee clamp 4 Bolt M12x245, A4 8 Jaw, small clamp 4 Washer BRB M12, A4 4 Backprofile, small clamp 2 Z-profile 8 Spring 4 U-bolt, 60mm-90mm 12 Nut M12, A4 8 Washer BRB M12, A4 4 Large washer BRBS M12, A4 16 Nut M12, A4 8 Locking spring 8 Lock nut LM M12, A4 Product Number SXK 107 2835/1

Length 790 mm

Product Number SXK 107 2837/1

Width 500 mm

Height 300 mm

Weight 45 kg

The dual panel antenna frame can be mounted on pole, wall or tower leg. Can be mounted on poles diam. 50mm, 80mm or 210mm or angle iron 50x50mm, 110x110mm or 150x150mm. It i s adjustable +- 45 degres in horizontal direction. If mounted according to the installation instruction it withstands wind speed up to 30m/s.

Width 130 mm

Height 90 mm

W eight 11.5 kg

Triple Antenna Support

Consist of: Qty Description 6 U-bolt, 45mm-60mm 24 Washer BRB M10, A4 48 Nut M10, A4 6 Bracket 6 Threaded rod HGS M10x120, A4 4 Distance 18mm, L=42mm Length 285 mm

Length 300 mm

Wall Mount, MHGA 

 Antenna support kit for two levels with space for 3 mounting tubes on one centre tube. Typical for installations of panel antennas. (Centre tube and mounting tubes not included). Triple antenna support can handle centre tube 75mm-120mm and mounting tube 45mm-60mm.

Product Number SXK 107 2836/1

Consist of: Qty Description 1 Tube, diam.114mm, t=5, L=3000mm 8 Jaw, small clamp 3 Tube, diam.60mm, t=3, L=2500mm 4 Backprifile, small clamp 1,5 Tripple antenna support (set) 8 Spring 9 U-bolt, 45mm-60mm 12 Nut, M12, A4 36 Washer BRB M10, A4 4 Large washer BRBS, M12. A4 72 Nut, M10, A4 8 Locking spring 9 Bracket 4 Bolt, M12x245, A4 9 Threaded rod HGS M10x120, A4 4 Washer BRB, M12, A4 6 Distance, diam.18mm, L=42mm 6 42 Threaded rod, HGS, M12x500, A4 2 Cue Dee clamp, back to back 1 Distance

Consist of: Qty Description 2 Mounting frame, upper and lower 1 Splitter bracket kit 1 Joint 2 Splitter, dual-panel 1 Bolt kit for joint 1 Cable kit, dual-panel 1 Tower clamp, upper 2 Antenna, low-band or high-b. 1 Tower clamp, lower 2 Antenna mounting kit 2 Counter block 1 Spacing plate, high-b.antennas 1 Pin bolt kit for tower clamps 1 Spare bolts 1 Cable clamp kit Product Number SXK 118 0932/1

Width 190 mm

Height 150 mm

W eight 2.6 kg

Length 3100 mm

Width 260 mm

Height 200 mm

Weight 40 kg

Extension Kit MHGA  Extension kit to Wall mount MHGA (SXK 118 0932/1), 2SP Antenna mounting frame. Consist of: Qty Description 2 Aluminium profile, L=2400mm 4 Screw bolt, M12x120 8 Washer Rb 13 4 Locking nut, M12 1 Tube of Gleitmo 40 Feeder clamp 4 Screw bolt, M8x100 4 Screw bolt, M8x70 8 Locking nut, M8 8 Washer, Rb 8,4 4 Screw bolt, M8x25 4 Locking nut, M8 4 Washer, Rb 8,4 Product Number SXK 118 0933/1

10

Length 2400 mm

Width 105 mm

Height 130 mm

Weight 16 kg

11

Mechanical Support for Equipment

Mechanical Support for Equipment

Mounting Brackets

Mounting Brackets

 AIR Support Support

Pole Mount Rear RBS/BBS 6301

The AIR support secures one AIR unit (Antenna Integrated Radio) or one panel antenna direct towards the tower leg of a telecom Mast/Tower. Mount it towards straight/inclined tower leg with the forms: round, square, profilewith 90 degree angle and profile with 60 degree angle. Max Azimuth adjustment: +/- 60 degree [Totally 120 degree]. Max inclination of tower leg: 4 Degree. Max mechanical tilt: 4 Degree. Max wind area (at 50m/s): 1,5m². Mounting range of AIR support. Minimum: [mm] Maximum:[mm]

Tubes Ø25 Ø120

Square 35x35 90x90

Profile angle 90 35x35 90x90

Profile angle 60. 40 mm width of opening. 100 mm width of opening.

Length 285 mm

Width 190 mm

Height 150 mm

Weight 8 kg

The Flexible ALD Mounting support fasten 1, 2 or 3 units of ALD:s (such as TMA/filters) to a Telecom Tower or Mast. With the "Extension ALD support" it is possible to mount up to three extra ALD units on the Flexible ALD Mounting Support. The Flexible ALD Mounting Support can be mounted towards Mast/tower leg with the forms: round, square, profile with 90 degree angle and profile with 60 degree angle. Max Wind Area (at 50 m/s): 0.5m². Mounting range of the Flexible ALD Support. Tubes Square Profile angle 90 Minimum: [mm] Ø25 35x35 35x35 Maximum:[mm] Ø120 90x90 90x90

Profile angle 60. 40 mm width of opening. 100 mm width of opening.

Number of required supports for the installation SXK1072854/1 SXK1072854/2 Number of ALD Flexible ALD Support Extension ALD Support 1, 2 or 3 ALD:s 1 Pcs 0 Pcs 4 Pcs ALD:s 1 Pcs 1 Pcs 5 Pcs ALD:s 1 Pcs 2 Pcs 6 Pcs ALD:s 1 Pcs 3 Pcs

Length 800 mm

Width 600 mm

Height 650 mm

Weight 33.48 kg

Width 135 mm

Consist of: Qty Description 1 Installation frame side 2 Mast attachment 1 Protection cover side Product Number NTM 201 4044/1

Length 800 mm

Width 600 mm

Height 650 mm

Weight 35.5 kg

Wall Mount Rear RBS 6301 Wall Support for RBS 6301 with protection cover for the rear and air spacer. Included screw and fasteners for wall mount. Supplied in an transport optimized package. Consist of: Qty Description 1 Installation frame rear 1 Protection cover rear 1 Air spacer Product Number NTM 201 4045/1

Length 1200 mm

Width 800 mm

Height 450 mm

Weight 36 kg

Omni Antenna Support This flexible tiltable support secures one omni directional antenna in the indoor ceiling (inbuilding). The antenna is mounted with a minimum distance (from ceiling) of 108 mm. With the supplied extension the antenna can be mounted 302 - 402 mm from the ceiling. This extension is usefull when large metalic objects such as girders, ventilation shafts blocks the broadcast.

Consist of: Qty Description 1 ALD Support, Clamp profile Aluminium 3 Mounting Tube Ø=60x3mm, L=400mm, Aluminium 1 Fastener set, Acid Proof Stainless Steel Length 410 mm

Product Number NTM 201 4043/1

Support for RBS/BBS 6301 with mast attachment and protection cover for the side. Included screw and fasteners for wall mount. Supplied in an transport optimized package.

Flexible ALD Mounting Support

Product Number SXK 107 2854/1

Consist of: Qty Description 1 Installation frame rear 2 Mast attachment 1 Protection cover rear

Pole Mount Side, RBS/BBS 6301

Consist of: Qty Description 1 Clamp Profile set, Aluminium 1 Rotate Plate, Acid proof Steel 1 Fastener set, Acid proof Steel Product Number SXK 107 2849/1

Support for RBS/BBS 6301 with mast attachment and protection cover for the rear. Included screw and fasteners for wall mount. Supplied in an transport optimized package.

Height 135 mm

Weight 4.8 kg

Extension ALD Mounting Support Extension ALD mounting support is used together with the Flexible ALD Mounting Support to increse the number of ALD´s to a maximum of 6 ALD´s. Compliance to ROHS 2 directives 2011/65/EU. Number of required supports for the installation. SXK1072854/1 SXK1072854/2 Number of ALD Flexible ALD Extension ALD Support 1, 2 or 3 ALD:s 1 Pcs 0 Pcs 4 Pcs ALD:s 1 Pcs 1 Pcs 5 Pcs ALD:s 1 Pcs 2 Pcs 6 Pcs ALD:s 1 Pcs 3 Pcs

Max antenna weight: 1.0 Kg Maximum Tilt: 15 degree Rotation: 360 degree Consist of: Qty Description 1 Adjustable bracket 1 Extension 302-402 1 Screw/Plug kit 1 Allen Key Product Number SXK 107 2845/1

Length 130 mm

Width 130 mm

Height 12 mm

Weight 1.6 kg

Consist of: Qty Description 1 Tube holder 1 Mounting tube Product Number SXK 107 2854/2

12

Length 550 mm

Width 100 mm

Height 85 mm

Weight 1.1 kg

13

Mechanical Support for Equipment

Mechanical Support for Equipment

Mounting Brackets

Freestanding

Parallel Cog Support

Guyed Roof Top Kit, 3.0 m

The Parallel cog support is designed for installation of panel antennas, small radio links, TMA or RRU. It has 205-300 mm off set between antenna tube and Tower/Mast strutting/profile. Tube is not included in kit.

The Guyed roof top kit is designed to meet the demands of a sturdy antenna mount for directional antennas and parabolas. Mount it on a roof top site where drilling through in the roof is not allowed. The construction is balanced with concrete blocks (500x500x50 mm). The blocks are not supplied in the kit.

The support kit has a wide clamping range and fits Tubes with diameter 25-120 mm Rectangular profiles: 35x35mm to 90x90 mm 90°Angle profiles: 35x35mm to 85x85 mm 60°Angle profiles: opening 45 mm to 100 mm Consist of: Qty Description 2 Parallel bracket C-C 134 2 Parallel bracket C-C 104 2 Clamp profile back 2 U-bolt 12 Washer M12 20 Nut M12 4 Bolt M12x35 8 Washer large M12 4 Lock nut M12 Product Number SXK 107 2843/1

Length 285 mm

Width 190 mm

Height 150 mm

W eight 6 kg

Product Number NTM 201 3164/1

Offset Support Kit The Offset support kit allows one RRU to be mounted behind a panel antenna without any extra equipment. The offset bracket can be mounted against tower and mast leg sections with diameters Ø = 25 - 76.1 mm. It fits against both tilt brackets and directly against the antenna. Max Net Wind Area* (at windspeed 50m/s): 1.2 m². *Offset bracket kit installed with a panel antenna. Consist of: Qty Description 2 Offset bracket 2 Clamp 2 U-bolt, M12 12 Nut/Washers Product Number SXK 107 2844/1

Consist of: Qty Description 1 Rubber carpet 1 16 Locking nut 1 Cross 4 Angle 1 Angle 4 Threaded rod 48 Washer 4 Mount f. Strut 50 Nut 12 Screw 4 Bottom plate 4 Screw 8 Screw 2 Clamp w. Ear 1 Foot 1 Tube 1 2 Screw Length 1200 mm

Width 800 mm

Hei ght 340 mm

Weight 80.5 kg

Roof Tube Single-based Self-supporting roof single-based system is design for small directional antennas, RRU:s and small parabolic dish. The non-penetrating mount is easy and fast to assemble. Height mounted: 2000 mm Foot print: ø = 600 mm, 0.3 m² Pole diameter: ø = 60 mm.

Length 250 mm

Width 150 mm

Height 100 mm

W eight 4 kg

Tubes  Antenna Tube These Aluminium tubes supports panel antennas, radio links, RRU and other telecom equipment. Choose between outer diameter Ø=60, 75, 90 or 114 mm. Choose between tube length 1.0 m, 1.5m 1.6m, 2.5 m 2.9 m and 4.0 m.

Consist of: Qty Description 1 Bottom plate 1 Upper plate 1 Rubber duct 1 Tube 3 Counter weight 3 Threaded rod 11 Nut, M6M 9 Washer, BRB 2 Screw, M6S Product Number NTM 201 1205/1

Length 625.2 mm

Width 625.6 mm

Hei ght 410.6 mm

Weight 91.1 kg

Consist of: Qty Description 1 Aluminium tube Product Number SXA 120 729/16

SXA 120 215/29 SXA 120 216/40 SXA 120 747/1 SXA 120 748/1 SXA 120 752/1

14

Length 1600 mm 2900 mm 4000 mm 1000 mm 2500 mm 1500 mm

Width 60 mm

Height 60 mm

W eight 2.3 kg

75 mm 90 mm 75 mm 60 mm 114 mm

75 mm 90 mm 75 mm 60 mm 114 mm

6.15 kg 14.4 kg 2.12 kg 2.32 kg 3.63 kg

15

Mechanical Support for Equipment

Cable Routing

Freestanding

Cable Runs Free-standing Ballast kit 2m

Greenfield Site Tower kit

Free-standing non penetrating rooftop.Typical rooftop.Typical for installation of panel antennas, radio links or other common telecom equipment.(Ballast not included)

This kit is designed for a Greenfield Tower site. It is a complete solution of installation material for the outdoor site. The cable runs, grounding wire, grounding rods, grounding bar and installation instructions are delivered in a transport optimized export package.

Consist of: Qty Description 4 Ballast box 3 Nut, M20 HTG 1 Upper tie bar fitting 1 Lock nut, M12, A4 1 EPDM rubber, 1050mmx1050mm 6 Washer, M20 HTG 1 Tube, diam.75mm, L=2000mm 2 Washer, M12, A4 1 Supporting tube, diam.60mm, L=1500mm 2 Bolt, M20x55H HTG 4 Distance, supporting tube diam.60mm 1 Bolt, M20x50 HTG 1 Plate, supporting tube diam.60mm 1 Pipe attachment 1 Support tube diam. 60mm 1 Corner attachment 8 Washer BRB, M8, A4 10 Bolt, M20x55H HTG 4 Lock nut, M8, A4 10 Nut, M20, HTG 4 Bolt, M8x75mm, A4 2 Lock nut, M12, A4 1 Plate, supporting tube 60mm 2 Lock nut, M8, A4 4 Washer BRB, M8, A4 2 Bolt, M12x45H, A4 4 Washer BRB, M12, A4 2 Bolt, M8x70, A4 4 Corner attachment1Washer, M20 HTG 1 Bolt M12x160, A4 2 Distance, diam.24mm, L=20mm Product Number NTM 201 3862/1

Length 2000 mm

Width 650 mm

Consist of: Qty Description 1 Cable ladder kit. 2x2.25m AluZinc 1 Basic wire kit, 70m, 35mm² 1 Cable ladder cover kit, 2x1.125m, AluZinc 1 Rod kit, 3m 1 Wire kit, 40m 35mm² 1 Installation instruction 1 Outdoor ground bar 1 Standard site material description Product Number NTM 201 3501/1

Width 480 mm

Height 540 mm

Cable Ladder Kit, AluZinc coated

Height 150 mm

Weight 111 kg

Consist of: Qty Description 2 Cable ladder 2.25m (W=400mm) AluZinc 1 Installation bolt set (25pcs) 2 Universal ladder fixture 4 Joint 6 Angle bracket 1 Screw set with plugs 2 End stop

The Free Standing Roof Tube is designed for non penetration installations on flat roofs of RRU´s and antennas. The support fits tube with diameter 60 mm. It has adjustable tilt up to 8°. Ballast up the support with four concrete slabs of thickness 40-65 mm (not included).

Product Number NTM 201 3138/1

Concrete slab (mm) 350x350x50 400x400x40 500x500x50

Cable Ladder cover kit, 2x1.125 m, AluZinc coated

Footprint (mm) 800x800 900x900 1100x1100

Length 300 mm

Length 2250 mm

Width 4150 mm

Height 80 mm

Weight 22 kg

The cover set protects the cable run between the mast and the base station. It avoids falling ice, smaller stones as well as sunlight damaging the feeder cables.

Consist of: Qty Description 2 Bracket,Ø Galvanized Steel 4 Roof Protection, Rubber 80x600 1 Nut/washer set, Stainless Steel Product Number SXK 107 2855/1

Weight 95.23 kg

 A high quality outdoor cable run for the Telecom application. Carries feeder cable , RRU cable , power cable, fiber and grounding cable. Modular cable carrying system for mount outdoors at rooftops, walls or between telecom masts/towers/antennas and shelters/flatpacks/RBS cabinets. Possible to mount free standing or supported. Heavy duty steel cable run of high quality with self-healing AluZinc coating. Long service life in corrosive environments. Easy assembly Mechanic system with package optimized for elevators/containers. Slim design easy to handle. Quick installation with universal joints and standard tools only. No sharp edges.

Free-standing Roof Tube

16

Length 2310 mm

Consist of: Qty Description 2 Protection cover (W=400mm) 1 Bolt set 14 pcs Width 300 mm

Height 200 mm

Weight 6.7 kg

Product Number NTM 201 3159/1

Length 1130 mm

Width 390 mm

Height 245 mm

Weight 16.6 kg

17

Cable Routing

Cable Routing

Cable Runs

Cable Runs

These kit is designed for a RBS room. Basic Indoor Kits is a complete solution of i nstallation material for the indoor site and can be ordered in two sizes. Cable ladders and profiles, grounding system, marking and sealing material are delivered in a transport optimized export package.

Cable Runs Basic Ladder kit Large Consist of: Qty Description 3 Cable ladderkit, Grey, 2x2,25m (W=300mm) 4 Cable kit 2m, 35mm², Yellow/Gree n 2 Cable tray, Grey, 2x0,6m, (W=150mm) 1 Common installation material 1 Cable sealing kit for 1/4"-7/8" cable 1 Site material description 1 Cable kit 25m, 35 mm²Yellow/Green 3 Indoor cable trunk, 2x2m Product Number NTM 201 3416/3

Length 2300 mm

Width 470 mm

Height 500 mm

Weight 80.25 kg

Consist of: Qty Description 2 Cable ladder kit, Grey, 2x2.25m (W=300mm) 3 Cable kit 2m, 35mm², Yellow/Gree n 2 Cable profile, Grey, 2x0.6m 1 Common installation material 1 Cable sealing kit, for 1/4" - 7/8" cable 1 Site material description 1 Grounding cable17m , 35mm², Yellow/Gree n 2 Indoor cable trunk 2x2m Length 2300 mm

Width 470 mm

Height 500 mm

Weight 57.15 kg

Consist of: Qty Description 2 Cable profile kit, 2x2m 1 Grounding cable kit,12m 1 Common installation kit 1 Cable sealing kit, IP54

Width 425 mm

Height 140 mm

Weight 21.5 kg

Consist of: Qty Description 6 Mesh tray,L= 2500mm W=75 mm,Pre-galvanized 10 Joint for mesh tray 10 Universal bracket 6 Divider plate, 25 mm L=2750 mm 20 Wall bracket 20 Fastening clamp 50 Installation bolt/nut 1 Equipped bond bolt Product Number NTM 201 4151/1

Length 2550 mm

Width 85 mm

Height 70 mm

Weight 20.9 kg

Cable Tray kit 2x2 m, Paint Coated, Grey  Length 2500 mm

Width 255 mm

Height 320 mm

Weight 38.6 kg

Cable Ladder kit, Paint Coated 300 mm Consist of: Qty Description 2 Cable ladder, Length 2250mm Width 300mm 3 Supporting Iron 4 Joint 3 T-bolt M10x35 4 Universal ladder fixture 3 Pendant bracket 6 Angle bracket 1 Bolt set M8x16 25-pack 1 Pendant rail 2250mm 2 Grounding screw Ø=9mm, 35mm² 2 Ceiling fixing 8 Screw set with plugs 5-pack M8x65 mm² 3 Cantilever arm Length 2260 mm

Width 325 mm

The cable try carries and covers cable inside a RBS-room or RBS-shelter. widht=0,1 m. Consist of: Qty Description 2 Cable ladder profile, 2000x100mm 2 Cable ladder profile cover, 2000x100mm 2 Profile End Piecs 40 Assembly Screw, B8 Product Number SXK 107 2023/1

Length 2010 mm

Width 110 mm

Height 70 mm

Weight 9.1 kg

Cable Tray Fitting Profile Cable Tray 50 mm wide for close installation environment. Can be mounted vertical or horizontal. Cables/fiber/ jumper cable are fixed by tie straps in the “mushroom-shaped" hole. Supplied with screw for wall mount and potential equalization bolt. High quality pre-galvanized and paint coated.

Height 85 mm

Weight 18.5 kg

Consist of: Qty Description 2 Cable tray, W=50 mm L=2000 mm 8 Screw TRX 4,5x50 mm 8 Plastic plug 6x42 mm 1 Mounting instruction 2 Equipotential bond bolt Product Number NTM 201 4152/1

18

Length 2250 mm

Cable Mesh tray for the indoor Telecom application 6x2500 mm x 75 mm. Carries feeder cable, power cable, fiber cable as well as grounding cables. Suitable in indoors environment. Supplied with mounting mounting accessories for wall mounting and mounting on existing cable ladder with a fastening clamp. Electrical continuity across joint according to SS-EN 61537:2001.

It can be mounted in container as well as RBS room and is supplied with cable inlet, grounding material, mounting profiles and fastening material.

Product Number NTM 201 3160/2

Consist of: Qty Description 2 Cable ladder, Length 2250mm Width 400mm 3 Supporting Iron 4 Joint 3 T-bolt M10x35 4 Universal ladder fixture 3 Pendant bracket 6 Angle bracket 1 Bolt set M8x16 25-pack 2 Pendant rail 2250mm 2 Grounding screw Ø=9mm, 35mm² 2 Ceiling fixing 3 Screw set with plugs 5-pack M8x65 mm 3 Cantilever arm 1 L-T-X branch

Mesh Tray Set

Indoor Installation Kit, light

Product Number NTM 201 3885/1

This indoor cable run is designed for mount in ceiling or on wall. The length, 2.25 meter, renders possible usage in buildings with narrow entrance, e.g. elevators. To obtain desired length of cable ladder: use several NTM 201 3745/1.

Product Number NTM 201 3745/1

Basic Ladder kit Medium

Product Number NTM 201 3416/2

Cable Ladder Kit, Paint Coated 400 mm

Length 2050 mm

Width 65 mm

Height 30 mm

Weight 2.8 kg

19

Cable Routing

Cable Routing

Cable Runs

Cable Runs Cable Tray, 2x0.6 m, Paint coated, Grey 

Outdoor Cable Tube kit

This product is mounted on the wall and used to l ead cables down from the cable run to the RBS cabinet,width =0,15m.

Fastening material for tower/mast mounting and wall mounting included.

Consist of: Qty Description 2 Fitting profile, 600x150x14 mm 2 Screw and plug set, 4,5x50 mm 4-pack 4 Grounding screw, M6x12mm, Ø = 9mm P rodu ct Nu Number

SXK 107 2158/2

Len gth 620 mm

Width 160 mm

Heigh t 25 mm

Weight

2.2 kg

P rodu ct Nu Number

Cable Tray, 2x2 m, Paint coated, Grey  The Cable Tray kit is a complement to the traditional Cable Ladder kit and is suitable for cable runs in close installation environment. It can be mounted on to vertical walls as well as on to horizontal ceiling. Cables are fixed to the Cable Tray with traditional tie straps. Widht=0,2m.

Len gth 2020 mm

NTM 201 3727/1

Len gth 1800 mm

Width 300 mm

Heigh t

Weight

300 mm

3.5 kg

Outdoor Slitted Conduit kit 27mm The tube kit is used for protection of cables and fiber against exterior mechanical influences.The tube is openable for easy installation of preassembled cables.Each tube is 2,1m long and inner diameter is 23.5mm, enough to fit one OIL cable and one power cable.

Consist of: Qty Description 2 Fitting profile, 2000x200x14mm 2 Screw and plug set, 4,5x50 4-pack 4 Grounding Screw, M6x12mm, Ø=9mm P rodu ct Nu Number SXK 107 761/2

Consist of: Qty Description 5 Cable conduit slitted 5 Straight coupler slitted 15 Tie strap, 457X9,5mm 1 Electrical tape, Black 20MX19MM 1 Electrical tape, Black 20MX50MM 30 Mounting screw 30 Plastic plug, Red 15 Conduit clamp

Width 210 mm

Heigh t 25 mm

Consist of: Qty Description 5 Conduit 27mm, L=2100mm

Weight 8.5 kg

P rodu ct Nu Number NTM 201 3929/1

Len gth 2200 mm

Width 90 mm

Heigh t 90 mm

Weight 2 kg

Clamping Band Clamping band that secures cable against the wall. Opening gap between wall and the clamping band is 5 mm. Hot-dip galvanized. Consist of: Qty Description 1 2.5m Clamping Band

Outdoor Slitted Conduit kit 48mm The tube kit is used for protection of cables and fiber against exterior mechanical influences.The tube is openable for easy installation of preassembled cables.Each tube is 2.1m long and innerdiameter is 44.0mm, enough to fit three OIL cables and three power cables.

P rodu ct Number

Len gth

Width

Heigh t

Weight

Max Clam pi ng Ø

Consist of: Qty Description 5 Conduit 48mm, L=2100mm

SXA 120 1869/1

2500 mm

30 mm

3 mm

1.71 kg

5 mm

P rodu ct Nu Number

NTM 201 3929/2

Indoor Cable Tray  The cable trunk is used indoor for protection of cables and fiber against exterior mechanical influences. Wall mounting or cable ladder mounting. Consist of: Qty Description 1 Screw,nut and washer kit 2 Cable trunk, 40x25mm L=2m 10 Screw 4,2x25mm, TGS-C3 10 Plastic wall plug, Red P rodu ct Nu Number NTM 201 3730/1

Len gth 2100 mm

Width 200 mm

Heigh t 200 mm

Weight 1.1 kg

Mini Tray On Roll White Mini Installation tray on 20 m roll made of silicone and cadmium-free PVC. Perfect for your indoor installation of RRU cabel/fiber or grounding cable. Backside with strong double-stick adhesive tape and perforated holes. Frontside with Self-locking lid. Supplied in a 20 meter roll with transport handle, instruction and bevel scale. Consist of: Qty Description 1 Mini tray 30x30mm x 20m P rodu ct Number MPB 901 026/1

Len gth 390 mm

Heigh t 125 mm

Weight 5.14 kg

Tray W/H/L 30 mm/30 mm/20 m

The flexible tube kit is used for protection of cables indoor against exterior mechanical influences. Consist of: Qty Description 2 Flexible Tube 25mm, l=3m 15 Tube holder 5 Jointing sleeve 3 Conduit elbow

20

Len gth 330 mm

Width 160 mm

Heigh t

Weight

130 mm

3.5 kg

Flexible Conduit kit 25m The flexible conduit kit is used for protection of cables against external mechanical influences. Inner diameter 40mm and it fits at least three OIL (optical)cables and three power cables for Main-Remote roof-top sites or or to be used in tower and mast.The flexible tube is 25m l ong. The kit also includes T-branches, fastener and pull wire for fast and easy installation. Consist of: Qty Description 25 Flexible conduit 50/40mm, including pullwire 5 Straight coupler for flex.conduit 50mm 2 T-branch for flex. conduit 1 Conduit clip, pack of 50 1 Mounting screw 25x4,2mm, pack of 100 1 Plastic plug, Red, 35x6mm, pack of 100 30 Tie strap, stainless steel plastic coated, 457x9,5 2 Electrical tape, Black P rodu ct Nu Number NTM 201 3811/1

Len gth 950 mm

Width 900 mm

Heigh t 250 mm

Weight 11 kg

Overlength Box Kit Width 390 mm

Tube kit, 2x3 m indoor

P rodu ct Nu Number NTM 201 218/3

Len gth 2200 mm

Width 330 mm

Heigh t 110 mm

Weight 1.13 kg

The box holds up to 30 m OIL cable excess length. It is easy to mount to a wall, tower leg etc and possible to stack on to each other. Consist of: Qty Consist 1 Box 1 Box cover 2 Cable Tie 457X9,5 1 Cable Tie Velcro tape 2 Bracket 4 Mounting bolt 4 Locknut 6 Cover bolt 4 Wall plugg TP2 red 4 Wall screw TGS-C3 4,2X25 4 Wall washer 4,3X8 P rodu ct Nu Number NTM 201 3729/1

Len gth 280 mm

Width 440 mm

Heigh t 42 mm

Weight 1.1 kg

21

Cable Routing

Cable Routing

Cable Runs

Cable Suspension Support Basic Cable Duct kit, 12 m

Wire Suspension Kit 50m

This cable duct kit made of recycled rubber can carry up to 4 pcs of 7/8" feeder cable and 2 pcs of grounding wire. The installation of the ducts does not require any mechanical fixing to flat roofs. The duct is simply l aid on the roof and is connected to the next one with the supplied jointing tube. This way you rapidly create a feeder cable infrastructure without penetrating the roof surface. With the supplied covers you can protect your connection to the grounding wire.

Support in stainless steel for Fiber/RRU/Feeder/Power cable in false ceiling. Possible to fasten the endbracket either on to the wall or i n the ceiling. Steel wire has a rupture limit at 5.9 kN.

Cable duct footprint: 0,3 m x 1 m Consist of: Qty Description 10 Cable Duct, Straight 1m 1 Cable Duct, Straight with grounding space 1m 1 Cable Duct, Straight with ground bar 1m 1 Grounding bar 1 Grounding Bolt Set, (10pcs) 1 Jointing Tube Set, (30pcs) 2 Cable Duct, Cover, 1m 1 Clamp Set, (100 pcs) 1 Cover Screw Set (20pcs) Product Number NTM 201 3469/1

Length 1020 mm

Width 600 mm

Product Number SXK 107 2851/1

Width 300 mm

Height 250 mm

Weight 5.85 kg

Wire Length 50 m

Support in stainless steel for Fiber/RRU/Feeder/Power cable in false ceiling. Possible to fasten the endbracket either on to the wall or i n the ceiling. Steel wire has a rupture limit at 5.9 kN. Height 670 mm

W eight 206 kg

Plastic trunking 6x2000mm Wall mounted 90x61mm with cover for residential and commercial telecom applications. Carries and protects feeder cable, RRU cable, power cable, fiber and grounding cable between antennas and cabinets. Supplied with accessories for T-joint, L-joint and End cap. Plastic trunking has punched holes in the base and internal clips (1clip/0.5m) for fastening of cable. Self-extinguishing Halogen-free Lead-free UV-constant Shock-proof

Consist of: Qty Description 1 Wire 100m, Steel 4mm, 72 Stringy 6 Wall Bracket, Steel 110 mm 6 Ceiling Bracket, Steel 70mm 12 Tightening device, Steel 24 Wire Lock, Steel, Max 25mm² Product Number SXK 107 2852/1

Length 400 mm

Width 300 mm

Height 250 mm

Weight 9.75 kg

Wire Length 100 m

Wire Support Ceiling Wire support fixed in the ceiling that suspends the steel wire. Distance between wire and ceiling mounted is 38 mm. The wire support are made of High Quality pre-galvanized steel. Consist of: Qty Description 1 Cable suspension support 38 mm, Steel

Consist of: Qty Description 6 Plastic trunking 2000 x 90 x 61 mm 6 Plastic trunking cover 61 mm 2 Internal Corner 90 degree 2 External Corner 90 degree 2 Elbow 90 degree 4 End Cap Length 2570 mm

Product Number SXA 120 1873/1

Height 290 mm

Width 20 mm

Height 30 mm

Weight 0.15 kg

Wall mounted bracket for the turnbuckle or wire stretcher.Fixed in the wall with anchor bolt or similar strong fastener.

W eight 13.5 kg

Consist of: Qty Description 1 Wall Bracket 110mm, Hot Dip galvanized Product Number SXA 120 1874/1

Wire Suspension Kit 25m Support in stainless steel for Fiber/RRU/Feeder/Power cable in false ceiling. Possible to fasten the endbracket either on to the wall or in the ceiling. Steel wire has a rupture limit at 5.9 kN. Consist of: Qty Description 1 Wire 25m, Steel 4mm, 72 Stringy 2 Wall Bracket, Steel 110 mm 2 Ceiling Bracket, Steel 70mm 2 Tightening device, Steel 4 Wire Lock, Steel, Max 25mm² Length 400 mm

Length 38 mm

Wall Bracket for Turnbuckle Width 360 mm

Cable Suspension Support

Product Number SXK 107 2850/1

Length 400 mm

Wire Suspension Kit 100m

Plastic Trunking

Product Number NTM 201 4153/1

Consist of: Qty Description 1 Wire 50m, Steel 4mm, 72 Stringy 4 Wall Bracket, Steel 110 mm 4 Ceiling Bracket, Steel 70mm 8 Tightening device, Steel 16 Wire Lock, Steel, Max 25mm²

Length 210 mm

Width 180 mm

Height 170 mm

Weight 9 kg

Bracket for Turnbuckle Wall mounted bracket for the turnbuckle or wire stretcher.Fixed in the wall with anchor bolt or similar strong fastener. Consist of: Qty Description 1 Wall Bracket 110mm, Hot Dip galvanized

Width 300 mm

Height 250 mm

W eight 3.6 kg

Wi re Length 25 m

Product Number SXA 120 1875/1

Length 110 mm

Width 90 mm

Height 50 mm

Weight 9 kg

Ceiling Bracket for Turnbuckle, Beam Mounting Fix the Bracket on I-beam. Maximum thickness of the I-beam is 20 mm. Attach bracket on wire strecther (hole dimater 11mm). The bracket are made of high grade steel and is hot dip galvanized. Consist of: Qty Description 1 Beam bracket, Steel Product Number SXA 120 1876/1

22

Length 220 mm

Width 180 mm

Height 160 mm

Weight 10 kg

23

Cable Routing

Cable Routing

Cable Suspension Support

Cable Support Kit (Hoisting Grip)

Beam Clips with Cable Tie Saddle

Cable Support Kit

Solid montage of steel constructions without drilling or welding. Supplied with saddle for attachment of Cable tie. Rupture limit: 220 N.

End support for three power cables and three OIL cables in the tower and mast, one hoisting grip for each cable. Three hosting grip for each oval quick link. The oval quick link fitted to the wire loop support.

Consist of: Qty Description 1 Beam Clamp

Consist of: Qty Description 2 Wire loop support 2 Oval quick link 3 Hoisting grip 6mm 3 Hoisting grip 12mm 2 Sewing-thread 700mm

Product Number SXA 120 1870/1 SXA 120 1871/1

SXA 120 1872/1

Length 50 mm 34 mm 400 mm

Width 40 mm 33 mm

266 mm

Height 25 mm 39 mm

W eight 0.01 kg 1.437 kg

280 mm

0.7 kg

Beam Clamp Range 5-9 mm 17-20 mm 10-16 mm

Product Number NTM 201 3728/1

Length 350 mm

Width 300 mm

Height 10 mm

Weight 0.435 kg

Cable Hanger for Wire Cable hanger for wire is designed to be fixed on steel wire and to carry cables and fiber. There are space for 6 cables with a maximum diameter of 16 mm. The bracket are made of steel and it is hot-dip galvanized. Consist of: Qty Description 1 Cable hanger, Steel Product Number SXA 120 1877/1

Length 220 mm

Width 180 mm

Height 160 mm

W eight 3 kg

Turnbuckle The turnbuckle is fixed on the wall/ceiling bracket or on the I-beam bracket. Use it to tighten the steel wire in the cable suspension system. It is made of steel and hot dip galvanized. Maximum adjustment is 100 mm and eye size is Ø = 9 mm Consist of: Qty Description 1 Turnbuckle M10x100mm, Steel 1 Washer M10 1 Nut M10 Product Number SXA 120 1878/1

Length 170 mm

Width 160 mm

Height 50 mm

W eight 5 kg

Wire Lock Wire lock for 4 mm steel wire.The wire lock is made of malleable hard iron and it is mounted with 2 pcs on each wire end. Consist of: Qty Description 1 Wire lock 4mm, Malleable hard iron 1 Shackel, Zinc plated steel 2 Nuts, Zinc plated steel Product Number SXA 120 1879/1

Length 150 mm

Width 150 mm

Height 30 mm

W eight 1.62 kg

Steel Wire, 4 mm Steel wire used as cable support in false ceiling, i n garage and tunnels. The 4 mm wire is made of zinc plated steel. Consist of: Qty Description 1 100m Wire, Zinc plated Steel, Ø=4mm with 72 core stranded Product Number SXA 120 1880/1

24

Length 400 mm

Width 300 mm

Height 250 mm

W eight 6.5 kg

25

Grounding and surge protection

Grounding and surge protection

Grounding Cables

Grounding Cables

Cable Kit 12 m, 35 mm² Yellow/Green

Cable Kit 25 m, 35 mm² Black

This kit is part of the Indoor grounding system for the RBS cabinet. Create a line, ring or tree type configuration of the grounding system with this kit. It is supplied with Main Earth Terminal (MET), branching and connection equipment.

This kit is part of the Indoor grounding system for the RBS cabinet. Create a line, ring or tree type configuration of the grounding system with this kit. It is supplied with Main Earth Terminal (MET), branching and connection equipment.

Consist of: Qty Description 1 Cable 12mx35mm²(2 AWG) Cu, Yellow/Green UL 90 °C 4 Jointing sleeve C89 6 Serrated washer, 8.4x15 4 Insulation cover 6 Nut M8 4 Cable lug, M8x35mm² 6 Washer 8.4x16x1.6 1 Grounding bar, 10x50mm² 6 Screw, M8x30 H, St 8.8 2 Screw, 5.5x64mm

Consist of: Qty Description 1 Cable 25m x 35mm²S1Z1-K, Black 10 Nut, M6M M8 2 Grounding bar, 10x50mm² 10 Washer, BRB 8.4x16x1.6 8 Cable Lug M10x35mm² 10 Screw, M6S M8x30 H St 8.8 8 Cable Lug M8x35mm² 4 Screw TKS type nr 12x64 8 Jointing Sleeve, C89 4 Wall Plug 8 Insulating Cover 1 Installation Instruction

Product Number NTM 201 3669/1

Length 330 mm

Width 330 mm

Height 60 mm

W eight 4.778 kg

Product Number 4/NTM 201 201/2

Length 330 mm

Width 330 mm

Hei ght 100 mm

Weight 10.45 kg

Hei ght 35 mm

Weight 0.48 kg

Hei ght 40 mm

Weight 0.84 kg

Hei ght 40 mm

Weight 0.7 kg

Cable Kit 17 m, 35 mm² Yellow/Green This kit is part of the Indoor grounding system for the RBS cabinet. Create a line, ring or tree type configuration of the grounding system with this kit. It is supplied with Main Earth Terminal(MET), branching and connection equipment. Consist of: Qty Description 1 Cable 17mx35mm2 (2 AWG) Cu, Yellow/Green UL 90°C 6 Jointing sleeve 8 Serrated washer, 8.4x15 6 Insulation cover 8 Nut, M8 6 Cable lug, M8x35mm² 8 Washer, 8.4x16x1.6 2 Grounding bar, 10x50mm² 8 Screw, M8x30 H, St 8.8 4 Screw, 5.5x64mm Product Number NTM 201 3669/2

Length 330 mm

Width 330 mm

Product Number 5/NTM 201 201/3

W eight 6.942 kg

Consist of: Qty Description 1 25m x 35mm²(2 AWG) Cu Yellow/Green, S1Z1-K UL 90 °C 4 Wall Plug 2 Grounding bar, 10x50mm² 10 Serrated washer, 8.4x15 8 Cable lug, M10x35mm² 10 Nut, M6M M8 ST 8 Cable lug, M8x35mm² 10 Washer, BRB 8.4x16x1.6 8 Jointing sleeve, C89 10 Screw, M6S M8x30 H 8 Insulating cover 1 Instruction 4 Screw, TKS NR 12x64 Width 300 mm

Length 140 mm

Width 140 mm

Cable Kit 2 m, 35 mm² Yellow/Green Height 70 mm

This kit is part of the Indoor grounding system for the RBS cabinet. Create a line, ring or tree type configuration of the grounding system with this kit. It is supplied with Main Earth Terminal (MET), branching and connection equipment.

Length 300 mm

Connect cabinets and racks to the indoor grounding system. Consist of: Qty Description 1 Cable 1m x35mm², Yellow/Gree n UL 90°C 1 Jointing Sleeve, C89 1 Cable lug M8x35mm² 1 Insulating Cover

Cable Kit 25 m, 35 mm² Yellow/Green

Product Number 4/NTM 201 201/3

Cable Kit 1 m, 35 mm² Yellow/Green

Height 80 mm

Connect cabinets and racks to the indoor grounding system. Consist of: Qty Description 1 Cable 2m x 35mm²Yellow/Green 1 Cable lug M8x35mm² 1 Jointing Sleeve, C89 1 Insulating Cover Product Number 5/NTM 201 201/4

Length 140 mm

Width 130 mm

Cable Kit 2 m, 25 mm² Black, Indoor Connect cabinets and racks to the indoor grounding system. Consist of: Qty Description 1 Cable 2mx25 mm², Black S1Z1-K UL 90° 1 Jointing Sleeve C89 1 Cable lug M8x25mm² 1 Insulating Cover Product Number 5/NTM 201 201/2 W eight 10.45 kg

Length 140 mm

Width 140 mm

Wire Kit 70 m, 35 mm² Ground the green-field site, roof top site or any outdoor site with a ring conductor arrangement (70m) with this kit. The ring conductor can be bonded with the MET, the Mast leg, the Cu wire and grounding rods with supplied parts. Consist of: Qty Description 1 70 m x 35 mm²Cu-wire, Annealed 7 stringy, 8 Screw, M6S M8x30H 8 Jointing Sleeve, C89 16 Contact Washer, M8 8 Cable Lug, M10x35mm² 8 Nut, M6M M8 Product Number NTM 201 3425/1

26

Length 420 mm

Width 420 mm

Hei ght 140 mm

Weight 22.1 kg

27

Grounding and surge protection

Grounding and surge protection

Grounding Cables

Grounding Cables

Wire Kit 40m, 25mm²

Grounding Cable 100 m Bulk Package Black

Creat a ring or line installation around the site with this kit. Branch-off from this ring to earth electrodes to protect existing or new equipment of shelters, masts, towers or antenna poles. The wire can be used as down conductor in mast/antennas. ROHS approved kit that gives your grounding system excellent electrical performance. Wire according to Swedish Standard SS240103. Achieve a crimp/branch-off according to SEN24510 and BS 4579:1 with this kit and the Ericsson approved tools. LTT 601 86 Mechanical crimping tool. LTT 601 89 Hydraulic crimping tool

Indoor grounding wire precut in 100 m length. Multi wire Cu cable with halogen-free sheath. IEC 60228 Class 5 and IEC 60332-1. ROHS approved kit. Rated voltage U0/U: 450/750 V. H07V-K.

Consist of: Qty Description 1 40m x 25mm²Cu Wire, 7-stringy soft annealed, High grade Cu, Diameter 6,4mm 6 Cable Lug M8x25mm², IEC 228 class 5, Tin plated with inspection hole, High grade Cu 6 Jointing sleeve C89, 6 Washer M8, Stainless Steel 6 Bolt M8x30,DIN 933 Stainless Steel 6 Nut M8, Acid proof Steel

P ro ro du du ct ct N um um be be r TEL 901 07/1 TEL 901 08/1

Product Number NTM 201 4145/1

Indoor grounding wire precut in 100 m length. Multi wire Cu cable with halogen-free sheath. IEC 60228 Class 5 and IEC 60332-1. ROHS approved kit. Rated voltage U0/U: 450/750 V. H07V-K.

Length 400 mm

Width 400 mm

Height 80 mm

W eight 9.6 kg

Wire Kit 40 m, 35 mm² Creat a ring or line installation around the site with this kit. Branch-off from this ring to earth electrodes to protect existing or new equipment of shelters, masts, towers or antenna poles. The wire can be used as down conductor in mast/antennas. ROHS approved kit that gives your grounding system excellent electrical performance. Wire according to Swedish Standard SS240103. Achieve a crimp/branch-off according to SEN24510 and BS 4579:1 with this kit and the Ericsson approved tools. LTT 601 86 Mechanical crimping tool. LTT 601 89 Hydraulic crimping tool. Consist of: Qty Description 1 40m x 35mm², Flexible Conductor, Annealed 7 Stringy, 6 Cable Lug M10x35mm² 6 Serrated Washer M8 6 Jointing Sleeve, C89 6 Nut, M6M M8 6 Screw, M6S M8x30 Product Number 9/NTM 201 230/1

Length 400 mm

Width 400 mm

Height 90 mm

W eight 13.1 kg

Consist of: Qty Description 1 50mx50mm²Flexible Conductor, Annealed 7-stringy 10 Jointing Sleeve, C89 Width 450 mm

W eight 23.5 kg

Rooftop Grounding, Grounding, Aluminium 40 m

Consist of: Qty Description 1 40m x 49 mm², Al-wire, 7-strand 6 Joint Clamp, Steel Ø=8-10mm

28

Length 400 mm

Width 400 mm

C ol ol ou ou r Black Black Black

35

Grounding Cable 100 m Bulk Package Yellow/Green

Consist of: Qty Description 1 100m Grounding Cable P ro ro du du ct ct N um um be be r TEL 901 07/2 TEL 901 08/2

TEL 901 09/2

L en en gt gt h 100 m 100 m 100 m

E le le ct ct ri ri ca ca l C ro ro ss ss S ec ec ti ti on on ( mm mm ²) 16 25

C ol ol ou ou r Yel low/Green Yel low/Green Yel low/Green

35

Consist of: Qty Description 1 Cable Flexible, Multi wire copper, Halogen Free IEC 60228 class 5, H07Z1-K 1 Cable lug M8 Tin-plated, Inspection hole, High grade copper IEC 228 class 5 P ro ro du du ct ct N um um be be r RPM 11 9 16 47/ 1 RPM 11 9 16 47/ 2 RPM 11 9 16 47/ 5 RPM 11 9 16 49/ 1 RPM 11 9 16 49/ 2 RPM 11 9 16 49/ 5

RPM 11 9 16 51/ 1 RPM 11 9 16 51/ 2 RPM 11 9 16 51/ 5

L en en gt gt h 22 0 mm 22 0 mm 22 0 mm 22 0 mm 22 0 mm 22 0 mm 22 0 mm 22 0 mm 22 0 mm

W id id th th 22 0 m m 22 0 m m 22 0 m m 22 0 m m 22 0 m m 2 20 20 m m 22 0 m m 22 0 m m 2 20 20 m m

H ei ei g ht 10 m m 10 m m 20 m m 10 m m 10 m m 30 m m 20 m m 20 m m 40 m m

W ei ei gh gh t 0. 26 265 kg 0. 41 415 kg 0. 87 875 kg 0. 35 355 kg 0. 59 595 kg 1. 31 31 kg 0. 45 455 kg 0. 77 779 kg 1. 76 76 kg

E le le ct ct ri ri ca ca l C ro ro ss ss S ec ec ti ti on on ( mm mm ²) 16 16 16 25 25 25

35 35 35

Cabinet Grounding Yellow/Green Height 150 mm

 A kit for grounding of a rooftop site. Use aluminium wire instead of copper cable/wire to reduce the risk of theft at site. Create a ring or grid configuration with the AL-wire and the supplied jointing clamps. Connect the supplied  AL wire with an external AL grounding wire Ø = 8-10mm in T, X, or parallel joint.

Product Number NTM 201 3755/1

E le le ct ct ri ri ca ca l C ro ro ss ss S ec ec ti ti on on ( mm mm ²) 16 25

Cabinet grounding/Cable Assembly for the indoor Telecom site. Supplied in lenghts of 1, 2 or 5 meter. Cable has rated Voltage 750 V. It is fire retardant according to IEC 60332-1. ROHS approved kit.

Creat a ring or line installation around the site with this kit. Branch-off from this ring to earth electrodes to protect existing or new equipment of shelters, masts, towers or antenna poles. The wire can be used as down conductor in mast/antennas. ROHS approved kit that gives your grounding system excellent electrical performance. Wire according to Swedish Standard SS240103. Achieve a crimp/branch-off according to SEN24510 and BS 4579:1 with this kit and the Ericsson approved tools. LTT 601 86 Mechanical crimping tool. LTT 601 89 Hydraulic crimping tool.

Length 450 mm

TEL 901 09/1

L en en gt gt h 100 m 100 m 100 m

Cabinet Grounding Black

Wire Kit 50 m, 50 mm²

Product Number 9/NTM 201 230/4

Consist of: Qty Description 1 100m Grounding Cable

Height 100 mm

W eight 6 kg

Cabinet grounding/Cable Assembly for the indoor Telecom site. Supplied in lenghts of 1, 2 or 5 meter. Cable has rated Voltage 750 V. It is fire retardant according to IEC 60332-1. ROHS approved kit. Consist of: Qty Description 1 Cable Flexible, Multi wire copper, Halogen Free IEC 60228 class 5, H07Z1-K 1 Cable lug M8 Tin-plated, Inspection hole, High grade copper IEC 228 class 5 P ro ro du du ct ct N um um be be r RPM 11 9 16 48/ 1 RPM 11 9 16 48/ 2 RPM 11 9 16 48/ 5

RPM 11 9 16 50/ 1 RPM 11 9 16 50/ 2 RPM 11 9 16 50/ 5 RPM 11 9 16 52/ 1 RPM 11 9 16 52/ 2 RPM 11 9 16 52/ 5

L en en gt gt h 22 0 mm 22 0 mm 22 0 mm 22 0 mm 22 0 mm 22 0 mm 22 0 mm 22 0 mm 22 0 mm

W id id th th 2 20 20 m m 2 20 20 m m 2 20 20 m m 2 20 20 m m 2 20 20 m m 2 20 20 m m 2 20 20 m m 2 20 20 m m 2 20 20 m m

H ei ei g ht 10 mm 10 10 mm 10 20 mm 20

10 1 0 mm 10 mm 10 30 mm 30 20 mm 20 20 mm 20 40 mm 40

W ei ei gh gh t 0. 26 5 kg 0. 41 5 kg 0. 87 5 kg 0. 35 5 kg 0. 59 5 kg 1. 31 k g 0. 45 5 kg 0. 77 9 kg 1. 76 k g

E le le ct ct ri ri ca ca l C ro ro ss ss S ec ec ti ti on on ( mm mm ²) 16 16 16

25 25 25 35 35 35

29

Grounding and surge protection

Grounding and surge protection

Grounding Cables

Grounding Bars and Rods (combined)

Indoor Grounding 3/8 - 1 5/8

Grounding Bar

This kit connects 3/8" - 1 5/8" feeder with the indoor grounding system.

Grounding bar for Telecom mast, tower and city site. Fasten this ground bar around tower tower leg or pipe with diameter Ø = 42-76 mm. Possible to fasten it against anchor rail and cable ladder. The grounding bar has ten M8 connections for grounding with cable lug.

Consist of: Qty Description 1 Hose Clip 1 Cable, 1x25mm², 2m 1 Insulating cover 1 Jointing Sleeve C89 1 Cable lug, 25mm² Product Number NTM 201 219/1

Length 210 mm

Width 160 mm

Height 30 mm

W eight 0.65 kg

Indoor Quick Grounding 16 - 35 mm², Bulk pack The UL-listed and patented ground wire connector joints two insulated multi-threaded Wires. Connected 2 wires with outer dimension 7.5-11,5mm and electrical cross section 16-35mm²(AWG2 - AWG6). Use it indoors for electrical feed thru and taps in the grounding and battery back-up system. Approved for use in telecom networks, minimum 20 years lifetime. Quick and easy product to use in a narrow space. Installer does not need any press tool for the connection of wires. Tighten with supplied tool or with cordless screwdriver LTT 129 09/2 and suitable bit.

The Quickgrip grounding joints cable with electrical cross section according to table below. Cross section 1 - Cross section 2 16mm²- 16mm² 16mm²- 25mm² 16mm²- 35mm² 25mm²- 25mm² 25mm²- 35mm² 35mm²- 35mm² Consist of : Qty Description 10 Grounding connector 7.5-11,5mm, 25-35mm², UL listed patented, 1 Tool Length 170 mm

Width 210 mm

Height 90 mm

W eight 0.87 kg

Grounding kit for the antenna system. Grounds TMA, RRU or filters at the Telecom site. ROHS2 approved kit with high quality components. Consist of: Qty Description 1 Grounding wire 16mm2, halogen free, 2 Cable lug 16mm2 1 Bolt, M6S M8x25 acid proof steel 2 Nut, M6S M8, acid proof steel 2 Washer, BRB M8,acid proof steel 1 Spring washer, FBB M8,acid proof steel 2 Heat shrink,25mm 12x2mm

Width 220 mm

Hei ght 60 mm

Weight 0.76 kg

Rod kit, 3 m

Length 30 mm

Consist of: Qty Description 2 Earth rod, 1500mm, Ø=5/8" 1 Cable clamp 5/8" / 25-50mm² 1 Tip 1 Coupling 1 Driving stud Product Number 9/NTM 201 230/2

Length 1505 mm

Width 80 mm

Hei ght 35 mm

Weight 4.1 kg

Tin plated high grade copper bar for the indoor Telecom Telecom Site. Insulated for mount on wall or fitting profile. It connects multi-stranded Cu wires with electrical cross section up to 50 mm². Consist of: Qty Description 1 Main Earth Terminal Product Number NGT 901 30/1 NGT 901 30/2

Length 180 mm 105 mm

Width 40 mm 40 mm

Hei ght 20 mm 20 mm

Weight 0.26 kg 0.145 kg

Connecti ons 10 5

Insulated Grounding Bar Grounding bar designed for lightning protection and potential equalization. Can be mounted in outdoor industrial environments. Supplied with plugs for wall montage. Lightning protection according to DIN V VDE V 0185 part 3 and Swedish standard SS EN 62305. Compliant with DIN VDE 0100 part 400 and part 540.

Width 150 mm

Height 200 mm

W eight 0.3 kg

Consist of: Qty Description 1 Grounding bar High grade Stainless steel 2 Insert screw M10x80mm 2 Plastic plug 2 Spring Washer 10,5x20x1 2 Insulators 10 M10 Connectors High grade Stainless steel Product Number SXK 107 2847/1

30

Length 350 mm

Main Earth Terminal

Grounding Kit Antenna System

Product Number NTM 201 4031/1

Product Number NTM 201 3326/1

System for deep grounding at green field site, container site or any outdoor site without any central grounding system. The rod kit can be used to either achieve a good lightening protection or to balance the electric potential in the outdoor grounding system. Supplied with connector for 25-50mm²grounding wire.

Storage -25°C to +55°C Transport -40°C to +70°C

Product Number NTM 201 3657/1

Consist of: Qty Description 1 Grounding bar 10xM8 1 VU-Bolt, M10 M8 CC-90 2 Screw, MC6S 6x20H 10 Screw, MC6S 8x20H 20 Washer, AZ 8.4 10 Washer, 8.4 2 Washer, AZ 6.4 2 Washer, 6.4 2 Washer, Ø=10.5x20mm 10 Nut, M6M M8 4 Nut, M6M M10

Length 408.5 mm

Width 40 mm

Hei ght 6 mm

Weight 1.9 kg

31

Grounding and surge protection

Grounding and surge protection

Grounding Bars and Rods (combined)

Grounding Cable Lugs

Potential Grounding PBC 6100, SSC-02

Cable lug M8, Bulk pack

This kit grounds the PBC 6100 and SSC02.

Tin-plated high grade copper M8 Cable lug in bulk package. Crimp on power and grounding cable at indoor/outdoor. Telecom site. It fits multi stranded wire, stranded wire as well as round conductor of copper. Inspection hole for a direct visual quality control of the crimp. Crimp on IEC 60228 Class 5 wire. ROHS approved.

Ground Bar Connects 1 wire x Ø = 8-10 mm 7 wire x max 25 mm² 1 band x 4x30 mm

 Achieve a Crimp/Connection according SEN 24510 and BS 4579:1 with ericsson approved tools LTT 601 86 or LTT 601 89.

ROHS 2 compliant Kit

Consist of: Qty Description 100 M8 Cable Lug

Consist of: Qty Description 7 Grounding wire16mm2, AWG5, IEC 60228 Class 5, Halogen Free 12 Cable lug , 16mm2, Hole Ø = 8 mm 1 Ground Bar 7x16mm2, Cover 4 Screw/Nut/Washer kit M6x12mm Product Number NTM 201 1217/1

Length 300 mm

Width 300 mm

Height 300 mm

W eight 1.589 kg

Product Number SNG 904 60/1 SNG 904 60/2 SNG 904 60/3

Length 70 mm 150 mm 150 mm

Width 90 mm 90 mm 90 mm

Height 90 mm 90 mm 90 mm

Weight 0.85 kg 1.3 kg 2.5 kg

Electri cal Cross Section 16 mm² 25 mm² 35 mm²

Cable lug M10, Bulk pack Tin-plated non-isolated cable lugs in bulk pack. Use these cable lugs f or connection and termination of Cu multithreaded wire, few-threaded wire as well as solid round conductor. Connect power cable, grounding cable or surge arrest cables (IEC 228 Class 2 and IEC 228 Class 5) at Telecom site. Use together with Ericsson approved crimping tool LTT 601 86 or LTT 601 89 to achieve a crimp according SEN 24510 and BS 4579:1

Grounding Joint Clamps Jointing Sleeve C89, Bulk Pack The sleeve joint/branch off thready Cu wires in the grounding and lightning protection system. Range of application is indoors, outdoors and even in the ground. Crimp wire and sleeve with tool LTT 601 86 or LTT 601 89 to achieve a connection according to SEN 24510 and BS 4579:1. Jointing sleeve made of tin plated high grade Cu ROHS2 compliant. The sleeve branch of IEC 228 Class 2 and IEC 228 class 5 wires with following Wire cross section.

Width 140 mm

Height 80 mm

Weight 2.4 kg

Used when connecting the RBS to the earthing system. Use the crimping tool set LTT 601 86/89 to accomplish a correct crimp. Consist of: Qty Description 2 Cable lug, Ø=50mm², hole 8mm 2 Cable lug, Ø=70mm², hole 8mm Length 150 mm

Width 85 mm

Height 85 mm

W eight 1.9 kg

Jointing Sleeve C89 The sleeve joint/branch off thready Cu wires in the grounding and lightning protection system. Range of application is indoors, outdoors and even in the ground. Crimp wire and sleeve with tool LTT 601 86 or LTT 601 89 to achieve a connection according to SEN 24510 and BS 4579:1. Jointing sleeve made of tin plated high grade Cu ROHS2 compliant. The sleeve branch of IEC 228 Class 2 and IEC 228 class 5 wires with following Wire cross section.

Product Number NTM 202 187/1

Width 19 mm

Width 60 mm

Height 20 mm

Weight 0.15 kg

Surge Protection DC Power Grounding  A grounding kit that is suitable for grounding of 12-30 mm coaxial cables and shielded power cables such as the DC power cable for the RRU. Waterproof sealing.

Product Number NGT 901 21/1

Consist of: Qty Description 1 Jointing Sleeve C89 Length 30 mm

Length 60 mm

Consist of: Qty Description 1 Contact bar ½ ., 3/8., 5/8. 7/8 1 Copper mesh 1 Socket head cap 2 Self-amalgating tape 1 Cable assembly 500mm, 16 mm² 2 Cable lug Ø = 8 , 16 mm ²

Cu Wire 1 - Cu Wire 2 16 mm²- 35 mm² 16 mm²- 50 mm² 25 mm²- 25 mm² 25 mm²- 50 mm² 35 mm²- 35 mm² 35 mm²- 50 mm² 50 mm²- 50 mm²

32

Length 90 mm

Cable lug Kit, 50 and 70 mm²

Consist of: Qty Description 50 Jointing Sleeve C89

Product Number SNT 102 26

Consist of: Qty Description 100 M10x35mm² Tin-plated,High Grade Cu, with inspection hole Product Number NTM 201 3477/1

Cu Wire 1 - Cu Wire 2 16 mm²- 35 mm² 16 mm²- 50 mm² 25 mm²- 25 mm² 25 mm²- 50 mm² 35 mm²- 35 mm² 35 mm²- 50 mm² 50 mm²- 50 mm²

Product Number SNT 901 14/1

Tested for a maximum voltage of 47 kV. ROHS2 Approved Mainly used for mount against Main Earth Terminal (MET) or appliance plug of material Cu.

Height 16 mm

Length 200 mm

Width 180 mm

Height 30 mm

Weight 0.161 kg

W eight 0.042 kg

33

Grounding and surge protection

Cables

Surge Protection

Coaxial Cables Feeder Grounding Quickgrip

1/2" Jumper Cables

The Quickgrip® feeder grounding protects feeder cable and radio equipment against surge from lightening stroke. It connects corrugated Cu feeder with size 1/2", 7/8", 1-1/4" or 1-5/8" against MET/tower/mast with M8 Bolt. The sealing/connection between Quickgrip and corrugated Cu feeder is quick, simple and does not need any tool for installation. Saves up to 80% in installation time against traditional grounding of feeder cable.

P ro ro du du ct ct N um um be be r TSR 951 331/1

- IP67 approved - No preparation of the cable is needed - No tools needed for installation - No use for additional sealing - Available in 4 dimensions 1/2” – 1 5/8” - Contact resistance