SLX Lock Mandrel Technical Datasheet

SLX Lock Mandrel Controlled locating, landing, and locking

Applications 

Description

Selective sub-surface controls

 The Evolution

with SLX (Otis® X) Profile

Profile Nipples.

 is built for use with SLX (Otis® X)

Nipples 

Plugging under pressure

 The lock mandrel has two locking keys, or dogs, dogs, to prevent both upward



Deploying instrument hangers

and downward movement once the device is engaged in the nipple. It

for bottom hole

has no No-Go intrinsic to the lock mandrel itself.

pressure/temperature measurements 

 The tool also features an internal internal fishing neck.

Positive locator for straddle systems



Nearly unlimited locations for

Operation

setting and locking subsurface flow controls

Non-selective use For non-selective running, attach the SLX Lock Mandrel and the required

Features & Benefits

flow control tool to the SLX Running Tool with the Lock Mandrel keys in

Straightforward installation

the locked position. Lower the tools into the tubing, tubing, to the required

and removal

depth. Once the Lock Mandrel engages with the nipple, put up to shear



Robust design

off the running tool, and retrieve.



Retractable locking keys



Locks designed to hold



pressure from above or below or from sudden reversals 

Extra-large ID for higher flow volumes

Selectiveuse When a Flow Control device is to be run selectively, the following procedure is followed. Attach the SLX Lock Mandrel and the required required flow control tool to the SLX SLX Running Tool. Lower the tools into the tubing, to the required depth.

Otis® is a registered trademark of Halliburton

 The running tool will hold the locking keys of the Lock Lock Mandrel in the retracted position until the desired landing nipple is reached. As the packing section of the Flow Control device passes through the seal bores section of the landing nipples, the resulting loss of weight will show on the weight indicator.  To set in an SLX Nipple (Otis®-Type X), X), pass through the nipple with the running tool. Once past, raise the running tool back up into the landing nipple.

This document is uncontrolled when printed.

© 2015 Evolution Evolution Oil Tools Inc. All rights reserved. reserved. www.eotools.com Toll Free: 1-800-265-TOOL

SLX_Lock_Mandrel_TDS_Rev_A (SLX Lock SLX_Lock_Mandrel_TDS_Rev_A Mandrel) February 2015

Trusted by over 1 million members

Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.

Trusted by over 1 million members

Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.

SLX Lock Mandrel

 This action causes a shift in the dogs on on body of the running tool, causing locking keys on the Lock Mandrel to expand. Set down the running tool again. The keys on the Lock Mandrel will locate and lock into the locking recess in the Landing Landing Nipple. Jar down to set the Lock Mandrel firmly in place. Jar up to shear the lower pin on the running running tool. Retrieve the running tool from the well.

Trusted by over 1 million members

Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.

CANADA

UNITED STATES OF AMERICA

#3, 1820 – 30th Ave NE

P.O. Box 5363

Calgary, Alberta T2E 7M5

2908 Coffey Street

 Toll Free: 1-800-265-TOOL (8665)

Victoria, Texas 77903

Main: 403-243-1442

Main: 361-575-7900

Fax: 403-258-2614

Fax: 361-575-8081

6415A - 63 St. Close

2400 Kermit Hwy

Lloydminster, Alberta T9V 3B5

Odessa, Texas 79764

 Tel: 780-522-8294

Cell: 432-638-7902

Fax: 780-875-6337 4512 – 81 Ave Edmonton, Alberta  Tel: 587-758-9091 Cell: 780-919-1722 Cell: 780-893-1019

www.eotools.com