sellos diaposotivas

7

Hydraulic Cylinders and Seals TABLE OF CONTENTS Introduction..........................................................................................................2 Hydraulic Cylinder Seals: Identification .............................................................................................5 Oversize Cylinders .................................................................................10 Seal Selection for Other Than Caterpillar Equipment.............................16 Press-In Wiper Seals..............................................................................17 Snap-In Wiper Seals...............................................................................20 U-Cup Seals ...........................................................................................23 Buffer Seals ............................................................................................28 Head Wear Rings ...................................................................................30 Metal Bearings for 300 HEX ...................................................................33 Head Seals .............................................................................................35 Piston Seals............................................................................................38 Piston Ring Seals ...................................................................................46 U-Cup Seal Assemblies..........................................................................53 Pin Seals ................................................................................................54 Snubber Seals ........................................................................................56 Troubleshooting......................................................................................57 Installation ..............................................................................................58 Hydraulic Cylinders & Seals Sorted by Machine Family and Model: How To Use This Section .......................................................................61 Agricultural Tractors ...............................................................................62 Articulated Trucks...................................................................................67 Backhoe Loaders....................................................................................83 Compactors - Landfill............................................................................119 Compactors - Soil .................................................................................121 Forest Machines - Feller Bunchers.......................................................123 Forest Machines - Forwarders..............................................................126 Forest Machines - Harvesters ..............................................................127 Forest Machines - Knuckleboom Loaders ............................................131 Forest Machines - Skidders..................................................................132 Front Shovels / Mass Excavators .........................................................139 Hydraulic Excavators............................................................................147 Integrated Toolcarriers .........................................................................212 Material Handlers .................................................................................219 Motor Graders ......................................................................................220 Multi Terrain Loaders............................................................................243 Off Highway Tractors............................................................................245 Off Highway Trucks ..............................................................................246 Paving Products - Asphalt Compactors................................................259 Paving Products - Asphalt Paving Equipment ......................................260 Paving Products - Cold Planers............................................................265 Paving Products - Pneumatic Compactors...........................................266 Paving Products - Road Reclaimers.....................................................267 Paving Products - Soil Stabilizers.........................................................267 Paving Products - Vibratory Compactors .............................................268 Pipelayers.............................................................................................268 Skid Steer Loaders ...............................................................................270 Telehandlers.........................................................................................275 Track Loaders.......................................................................................283 Track-Type Tractors .............................................................................313 Wheel Dozers .......................................................................................346 Wheel Loaders .....................................................................................352 Wheel Tractor Scrapers........................................................................399 Part Number Index...........................................................................................438

1

Hydraulic Cylinders and Seals INTRODUCTION

THIS BOOK IS FOR CATERPILLAR AND CATERPILLAR DEALER USE ONLY! IT SHOULD NOT BE DISTRIBUTED T O CUSTOMERS This Reference Guide contains part number and dimensional information to assist Caterpillar Dealers in the servicing of Cat® hydraulic cylinders. It also contains information on identifying seals for use on other than Cat equipment. It is NOT intended for distribution outside Caterpillar Dealerships.

Purpose of This Guide This guide provides Caterpillar Dealer parts and service personnel with a quick reference to information on Caterpillar cylinders, seals, Reman Cylinders and Rods, and Caterpillar Seal Kits. It is not a replacement for Caterpillar’s Hydraulic Information System (HIS)*, Service Information System (SIS), or other on-line sources. Information in this book always should be checked against these sources which are updated regularly. * Caterpillar’s Hydraulic Information System remains free to dealers via the Extranet https://his.cat.com . Users must obtain authorization and possess a Cat Web Security ID.

How This Guide is Organized The book has three basic sections. The first section provides information on hydraulic cylinder seals. Information covers seal identification, applications, oversize seals, part numbers for the different types of seals, troubleshooting techniques when a failure occurs, and installation. The second and largest section of the book contains general information on Cat hydraulic cylinders. Sorted by machine model for easy referencing, this information includes cylinder group and cylinder assembly part numbers, engineering change levels, cylinder length and bore diameter, rod length and diameter, and part numbers for Cat Reman Cylinders, Cat Reman Rods, and Cat Standard and Oversize Seal Kits. The last section consists of a part number / page number cross-reference. This section will come in handy if you have a part number and want to know what page it appears on.

2

Hydraulic Cylinders and Seals INTRODUCTION

Cat Reman Cylinders and Rods Caterpillar offers Remanufactured Cylinders and Rods to get the customer back to work quickly. This is an Exchange program, so for each remanufactured unit sold a core (scratched or damaged cylinder or rod) must be returned. Even if ruptured or broken, the core can qualify for partial core credit. Cat Remanufactured Cylinders and Rods are available off-the-shelf for most Cat applications at prices a fraction of new.

Cat Hydraulic Cylinder Seal Kits The most common cylinder repair is a reseal – and your dealership has a lot to offer customers for this repair. Customers need to be informed there’s a lot more to resealing cylinders than just installing new seals. Your dealership is committed to resealing cylinders right. That means using proper disassembly and assembly equipment, light honing cylinder tubes, practicing contamination control, checking for other problems such as dented or scored rods, and pressure testing after reassembly. Another benefit of your dealer’s reseal service is the large inventory of Cat Hydraulic Cylinder Seal Kits. Not only do these kits contain genuine Cat seals, one part number provides all the seals necessary to reseal a Cat cylinder at a price less than the sum of the individual parts.

3

Hydraulic Cylinders and Seals IDENTIFICATION

Seal Identification What is a Seal? A seal is a device which prevents the escape or passage of a fluid (liquid or gas). A hydraulic cylinder seal is used to seal two surfaces under fluctuating pressure conditions.

Hydraulic Cylinders: The hydraulic cylinder is the tool which converts hydraulic fluid pressure into work. Even though there are many different designs of hydraulic cylinders, they are relatively similar in the way they are sealed and repaired. Because of this similarity, this guidebook will not address different types of designs. It will suffice to mention that Caterpillar manufactures three different designs: bolt-on head, threaded crown and threaded gland cylinders.

Hydraulic Cylinder Seals: Caterpillar seals are available as either individual pieces or kits. Kits offer a convenience as well as a cost-savings, priced substantially below the sum of the individual pieces. Caterpillar hydraulic seals can be used on other makes of cylinders. Cat also offers some of the most popular seal configurations and sizes designed solely for other makes of hydraulic cylinders.* *Note: Check for availability in your subsidiary.

Identifying Hydraulic Cylinder Seals Refer to the hydraulic cylinder illustration below. The seals in this Caterpillar cylinder are those typically found in hydraulic cylinders.

Use the seal pictures, cross-sections, cutaway illustrations and descriptions on the following pages to help you identify the different types of hydraulic cylinder seals.

4

Hydraulic Cylinders and Seals IDENTIFICATION 1a. Press-in Wiper Seal - prevents external contaminants from entering the system. Single-lip (the lip is the projecting rim or edge of the seal) wipers clean the rod as it retracts. Double-lip wipers clean the rod as it retracts and seals oil, eliminating “weeping” (cosmetic leakage). The double-lip wipers are secured in place with a bearing mount. These urethane wipers are metal-encased for added strength. They are often referred to as “canned” wipers (metal-encased) or “J” wipers (the metal often forms a “J” shape when viewed in the cross-section).

Type A Single-lip wiper

Type B Double-lip wiper

Type C Modified

Type D Modified Single

1b. Snap-in Wiper Seal - prevents external contaminants from entering the system, but used in less severe environmental conditions and lighter duty hydraulic applications than its press-in counterpart.

Type Reg

5

Hydraulic Cylinders and Seals IDENTIFICATION The following various types of snap-in wipers are available for use on other makes of hydraulic cylinders. “Type SHU” wipers are slotted heel, universal style urethane wipers. The slotted heel acts as a relief slot to prevent a pressure trap occurring between the rod seal and the wiper. A pressure trap is excessive fluid pressure “trapped” between two seals.

Type SHU

“Type AN” wipers are a non-current design, originally made for the military (AN refers to Army/Navy). This single-lip wiper is made of urethane.

Type AN

6

Hydraulic Cylinders and Seals IDENTIFICATION Loaded u-cups are also available for use on other makes of cylinders. The “Type E” loaded u-cup has a back-bevel lip for increased sealability.

Type D Backup Ring Type F

Type E

3. Buffer Seal -acts as a secondary rod seal and protects the rod from sudden increases in system pressure. There are currently three types of buffer seals. Type A is a one-piece seal made of urethane. Type B is a two-piece bronze filled PTFE seal with a nitrile expander. The notched view in the cross section must face the pressure side for maximum seal performance. Type C is a two-piece urethane seal with a thermoplastic backup ring. This design allows the seal to withstand higher pressures. Type B and Type C buffer seals are designed to prevent seal extrusion and pressure trapping.

Type A

Type B

Type C

7

Hydraulic Cylinders and Seals IDENTIFICATION 4. Head Wear Ring - eliminates metal-to-metal contact between the head and rod and prevents scoring (scratching) of the rod by the head.

4a. Metal Bearing for 300 HEX - used instead of plastic head wear ring for many 300 HEX hydraulic cylinder groups. The coated bearing is pressed into the cylinder group head and held in place with a split metal retaining ring. This bearing supports the hydraulic cylinder rod and prevents metal-to-metal contact between the head and the cylinder rod. See the “Metal Bearings for 300 HEX” section for complete listing.

5. Head Seal - a two-piece seal, consisting of a nitrile o-ring and a backup ring, which seals the head to the cylinder wall.

8

Hydraulic Cylinders and Seals IDENTIFICATION 6. Piston Seal - a two-piece seal, consisting of a piston ring and an expander, which prevents oil transfer between the rod end of the cylinder and the cap end. The piston seal is usually made of Teflon, with nylon available for pressures greater than 3000 psi (20,670 kpa). The various shaped expanders are nitrile. Type 4 consists of a teflon piston ring with a nitrile rubber expander. Type 5 consists of a rubber expander surrounded by bronze filled Teflon on both sides. Type 6 is a urethane u-cup seal used in single acting cylinders. Type 1

Type 2

Type 3

Type 4

Type 5

Type 6

7. Piston Wear Ring - supports and centers the piston to prevent metal-to-metal contact between the piston and the cylinder wall.

Chevron Packing - used as gland packing in place of rod seals for high pressure applications. While Caterpillar no longer uses this seal design, which is made of a multi-compounded material (usually cotton duck cloth and nitrile), it is often referred to as V-Packing, the shape formed by its cross-section. The end adapters can be tightened down, making the seal adjustable. PACKING GLAND

HEAD

CHEVRON ROD PACKING (STACKED V-RINGS)

PRESS IN OR SNAP IN WIPER

9

Hydraulic Cylinders and Seals OVERSIZE CYLINDERS

Oversize Threaded-Gland Cylinder The head seal for the oversize threaded-gland cylinder is the standard O-ring and back-up ring. See Illustration 1.

Illustration 1. Threaded gland with standard head seal. 18 = Head seal.

Oversize Threaded-Crown Cylinder The head seal for the oversize threaded-crown cylinder is an oval cross-section seal that locates in the lead-in chamfer at the open end of the cylinder. The O-ring and back-up ring groove in the head is left empty. See Chart 2 for part numbers.

Chart 2 Oversize Seals Standard Bore Size 2.50 2.75 3.00 3.25 3.50 3.75 4.00 4.25 4.50 4.75 5.00 5.25 5.50 6.00 6.25 6.50 7.00 7.25 7.50 7.75 8.25 8.50 9.25 10.00 10.25 10.50 11.50

10

Oversize Head Seal 8C4889 8C4890 8T8367 8C4891 8T8368 8T8369 8T8370 8T8371 8T8372 8T8373 8T8374 8T8375 8T8376 8T8377 8T8378 8T8379 8T8380 8T8381 8C0553 8C4892 8T8382 8C4893 8T8383 8C4895 8C4896 8C4897 8C4898

Illustration 2. Threaded crown with oval seal. 19 = Oval seal.

Hydraulic Cylinders and Seals OVERSIZE CYLINDERS

Cylinder Assembly Chamfer Dimensions Oversize threaded crown cylinders are sealed by using an oval head seal that locates in the lead-in chamfer of the cylinder bore. After the cylinder has been honed, compare the chamfer to the specifications in Illustration 4. Note: Chamfers that do not meet specifications will cause leaks. If the chamfer is too deep, it can be shortened by machining a maximum of 3.0 mm (.12 in) from the end of cylinder tube (2). If the end of the cylinder is machined, during assembly, check to make sure the crown can be fully threaded onto the cylinder and the threads do not bottom before the head is seated against the cylinder. If the chamfer is not concentric with the cylinder bore, the chamfer must be re-machined so that it is concentric and perpendicular to the bore.

Chamfer Dimensions for Oval Head Seals Chamfer Dimensions Item

Dimension

E

Standard bore

F

0.76 (.030) oversize

H

9.7 (.38) max. on standard size bore

J

8.1 (.32) max. on 0.76 (.030) oversize bore

L

15°

Item 2

Illustration 4.

Description Tube

3

Head

19

Oval Head Seal

21

Rod

11

Hydraulic Cylinders and Seals OVERSIZE CYLINDERS

Cylinders that Cannot Use Oval Head Seals Some cylinders cannot accept oval head seals. These cylinders use heads that have a “relief” machined into the square corner where the oval head seal normally locates. Because of the relief, the oval head seal will not fill the cavity and seal the joint. If the cylinder uses a head listed in Column A, it should not be oversized. Instead, offer the customer the retube option through your shop or a Caterpillar Remanufactured Standard Cylinder. If the cylinder uses a head listed in Column B, the cylinder may be honed oversize and oversize seals used.

Oval Head Seals – Chart 3

12

Cylinder Group No. 3G2221 3G2221 3G2222 3G2222 3G4598 3G4599 3G5712 6J7810 7J1487 7J1488

Column A Former Relieved Head 9J1747 1U1807 9J1747 1U1807 9J3379 9J3379 9J3379 6J7804 9J0499 9J0499

Column B Current NonRelieved Head 9T3968 9T3968 9T3968 9T3968 9T3509 9T3509 9T3509 9T6541 9T5896 9T5896

8J5779 8J6337 8J6338 9J3632 1U1766 1U1767 1U1771

8J5780 8J6225 8J6225 9J3626 9J3379 9J3379 3G4415

9T6543 9T6543 9T3501 9T3509 9T3509 9T3509

1U4679

8J5780

Effective “In” Change Level of Current Head 9 9 9 9 11 9 3 5 4 4 Group Cancelled & Replaced by 4T7585 4 4 4 5 5 3 Group Cancelled & Replaced by Multiple Numbers

Hydraulic Cylinders and Seals OVERSIZE CYLINDERS

Oversize Bolted-Head Cylinder Formerly, the head seal for the oversize bolted-head cylinder was the same oval seal that is used in an oversize threaded-crown cylinder. The oversize bolted-head cylinder is now sealed at the head joint by an O-ring which provides a more effective seal than the oval head seal. An oversize bolted-head cylinder that has successfully operated with the oval seal may be re-sealed without machining the O-ring groove into the flange face. However, it is recommended that the oval seal be replaced by the flange face O-ring seal. Most oversize seal kits include both the oval seal and the O-ring seal in order to accommodate re-seal requirements of both former and current designed cylinders. Caterpillar’s current remanufactured oversize cylinders (bolted-head type) have the O-ring groove machined into the flange face of the cylinder assembly.

Illustration 3. Bolted head with face O-ring seal. 20 = Face O-ring seal.

New Groove Dimensions for O-ring Part Numbers Oversize bolted-head cylinders that lack the flange face o-ring groove can be reworked to add the groove. Recommended dimensions for the cylinder o-ring face seal grooves have been modified to increase the nominal compression of the o-ring face seal. Recommended groove widths have increased and groove depths have decreased. Recommended groove diameters have not changed. O-ring face seal part numbers also have not changed. The recommended o-ring face seal part numbers and o-ring face seal groove dimensions are listed in Chart 4. Refer to Illustration 5 for clarification. Dealers who salvage cylinder assemblies of bolted-head cylinder groups by honing the bore oversize will need to use the new dimension recommendations to machine grooves for o-ring face seals. Bolted head cylinder assemblies already having o-ring face seal grooves should not be re-worked to the new groove dimensions. Note: Some cylinder assemblies have been dealer re-worked to add an o-ring groove to the flange face of the head rather than the cylinder. Do not assemble a cylinder that would mate a cylinder and head both having an o-ring groove.

A. B. C. D.

Groove Diameter Groove Width Groove Depth Radius

Illustration 5. Seal Groove Width Dimensions See Chart 4 for item reference and dimensions.

13

Hydraulic Cylinders and Seals OVERSIZE CYLINDERS Seal Part Numbers and Machining Dimensions

Chart 4 Seal Part Numbers and Groove Dimensions Cyl. Nominal Bore Dia.

O-ring Face Seal Part No.

Groove Dia. (A)

Groove Width (B)

Groove Depth (C)

Radius (D)

76.20 (3.000) 88.90 (3.500) 95.25 (3.750) 101.60 (4.000) 107.95 (4.250) 114.30 (4.500) 120.00 (4.720) 120.65 (4.750) 127.00 (5.000) 133.35 (5.250) 139.70 (5.500) 140.00 (5.510) 152.40 (6.000) 158.75 (6.250) 160.00 (6.300) 165.10 (6.500) 170.00 (6.690) 177.80 (7.000) 180.00 (7.090) 184.15 (7.250)

5P2931

87.12 ± 0.50 (3.430 ± .020) 101.96 ± 0.05 (4.014 ± .020) 106.30 ± 0.50 (4.185 ± .020) 112.52 ± 0.50 (4.430 ± .020) 121.00 ± 0.50 (4.764 ± .020) 127.36 ± 0.50 (5.014 ± .020) 136.00 ± 0.50 (5.354 ± .020) 136.45 ± 0.50 (5.372 ± .020) 137.92 ± 0.50 (5.430 ± .020) 149.15 ± 0.50 (5.872 ± .020) 152.76 ± 0.50 (6.014 ± .020) 155.50 ± 0.50 (6.122 ± .020) 165.46 ± 0.50 (6.514 ± .020) 171.81 ± 0.50 (6.764 ± .020) 176.15 ± 0.50 (6.935 ± .020) 179.17 ± 0.50 (7.054 ± .020) 187.50 ± 0.50 (7.382 ± .020) 198.98 ± 0.50 (7.834 ± .020) 196.50 ± 0.50 (7.736 ± .020) 198.98 ± 0.50 (7.834 ± .020)

2.40 ± 0.05 (.094 ± .002) 3.53 ± 0.08 (.139 ± .003) 2.40 ± 0.05 (.094 ± .002) 2.40 ± 0.05 (.094 ± .002) 3.53 ± 0.08 (.139 ± .003) 3.53 ± 0.08 (.139 ± .003) 3.53 ± 0.08 (.139 ± .003) 4.75 ± 0.13 (.187 ± .005) 2.40 ± 0.05 (.094 ± .002) 4.75 ± 0.13 (.187 ± .005) 3.53 ± 0.08 (.139 ± .003) 4.75 ± 0.13 (.187 ± .005) 3.53 ± 0.08 (.139 ± .003) 3.53 ± 0.08 (.139 ± .003) 3.53 ± 0.08 (.139 ± .003) 3.53 ± 0.08 (.139 ± .003) 3.53 ± 0.08 (.139 ± .003) 4.75 ± 0.13 (.187 ± .005) 4.75 ± 0.13 (.187 ± .005) 4.75 ± 0.13 (.187 ± .005)

1.33 ± 0.05 (.052 ± .002) 1.95 ± 0.08 (.077 ± .003) 1.33 ± 0.05 (.052 ± .002) 1.33 ± 0.05 (.052 ± .002) 1.95 ± 0.08 (.077 ± .003) 1.95 ± 0.08 (.077 ± .003) 1.95 ± 0.08 (.077 ± .003) 2.64 ± 0.13 (.104 ± .005) 1.33 ± 0.05 (.052 ± .002) 2.64 ± 0.13 (.104 ± .005) 1.95 ± 0.08 (.077 ± .003) 2.64 ± 0.13 (.104 ± .005) 1.95 ± 0.08 (.077 ± .003) 1.95 ± 0.08 (.077 ± .003) 1.95 ± 0.08 (.077 ± .003) 1.95 ± 0.08 (.077 ± .003) 1.95 ± 0.08 (.077 ± .003) 2.64 ± 0.13 (.104 ± .005) 2.64 ± 0.13 (.104 ± .005) 2.64 ± 0.13 (.104 ± .005)

0.4 ± 0.05 (0.16 ± .002) 0.4 ± 0.10 (.016 ± .004) 0.4 ± 0.05 (.016 ± .002) 0.4 ± 0.05 (.016 ± .002) 0.4 ± 0.10 (.016 ± .004) 0.4 ± 0.10 (.016 ± .004) 0.4 ± 0.10 (.016 ± .004) 0.8 ± 0.20 (.031 ± .008) 0.4 ± 0.05 (.016 ± .002) 0.8 ± 0.20 (.031 ± .008) 0.4 ± 0.10 (.0.016 ± .004) 0.8 ± 0.20 (.020 ± .008) 0.4 ± 0.10 (.016 ± .004) 0.4 ± 0.10 (.016 ± .004) 0.4 ± 0.10 (.016 ± .004) 0.4 ± 0.10 (.016 ± .004) 0.4 ± 0.10 (.016 ± .004) 0.8 ± 0.20 (.031 ± .008) 0.8 ± 0.20 (.031 ± .008) 0.8 ± 0.20 (.031 ± .008)

14

4F4097 7X5494 9X7357 6S3002 9X7566 1330128 3F5792 1313716 2D8009 9X7358 2K8257 8T6404 9X7391 9D8042 9D8042 9X7725 5J2383 5J2383 5J2383

190.50 (7.500)

3J0634

211.68 ± 0.50 (8.334 ± .020)

4.75 ± 0.13 (.187 ± .005)

2.64 ± 0.13 (.104 ± .005)

0.8 ± 0.20 (.031 ± .008)

196.85 (7.750)

3J0634

209.47 ± 0.50 (8.247 ± .020)

4.75 ± 0.13 (.187 ± .005)

2.64 ± 0.13 (.104 ± .005)

0.8 ± 0.20 (.031 ± .008)

200.00 (7.87)

5P3092

225.00 ± 0.50 (8.858 ± .020)

7.40 ± 0.20 (.291 ± .008)

3.95 ± 0.20 (.155 ± .008)

1.6 ± 0.40 (.063 ± .016)

209.55 (8.250)

4K6804

224.38 ± 0.50 (8.834 ± .020)

4.75 ± 0.13 (.187 ± .005)

2.64 ± 0.13 (.104 ± .005)

0.8 ± 0.20 (.031 ± .008)

215.90 (8.500)

1T0132

241.22 ± 0.50 (9.496 ± .020)

4.75 ± 0.13 (.187 ± .005)

2.64 ± 0.13 (.104 ± .005)

0.8 ± 0.20 (.031 ± .008)

220.00 (8.66)

1M9015

253.92 ± 0.50 (9.997 ± .020)

9.35 ± 0.25 (.368 ± .010)

5.20 ± 0.25 (.207 ± .006)

1.6 ± 0.40 (.063 ± .016)

234.95 (9.250)

5S3676

253.92 ± 0.50 (9.997 ± .020)

4.75 ± 0.13 (.187 ± .005)

2.64 ± 0.13 (.104 ± .005)

0.8 ± 0.20 (.031 ± .008)

Hydraulic Cylinders and Seals OVERSIZE CYLINDERS

Chart 4 Seal Part Numbers and Groove Dimensions Cyl. Nominal Bore Dia.

O-ring Face Seal Part No.

Groove Dia. (A)

Groove Width (B)

Groove Depth (C)

Radius (D)

254.00 (10.000) 266.70 (10.500) 279.40 (11.00) 292.10 (11.50) 317.50 (12.50) 330.20 (13.00) 342.90 (13.50)

3S3074

276.15 ± 0.50 (10.872 ± .020) 288.85 ± 0.50 (11.372 ± .020) 310.50 ± 0.50 (12.224 ± .020) 314.25 ± 0.50 (12.372 ± .020) 360.50 ± 0.50 (14.193 ± .020) 381.50 ± 0.50 (15.020 ± .020) 381.50 ± 0.50 (15.020 ± .020)

7.40 ± 0.20 (.291 ± .008) 7.40 ± 0.20 (.291 ± .008) 7.40 ± 0.20 (.291 ± .008) 7.40 ± 0.20 (.291 ± .008) 7.40 ± 0.20 (.291 ± .008) 7.40 ± 0.20 (.291 ± .008) 7.40 ± 0.20 (.291 ± .008)

3.95 ± 0.20 (.155 ± .008) 3.95 ± 0.20 (.155 ± .008) 3.95 ± 0.20 (.155 ± .008) 3.95 ± 0.20 (.155 ± .008) 3.95 ± 0.20 (.155 ± .008) 3.95 ± 0.20 (.155 ± .008) 3.95 ± 0.20 (.155 ± .008)

1.6 ± 0.40 (.063 ± .016) 1.6 ± 0.40 (.063 ± .016) 1.6 ± 0.40 (.063 ± .016) 1.6 ± 0.40 (.063 ± .016) 1.6 ± 0.40 (.063 ± .016) 1.6 ± 0.40 (.063 ± .016) 1.6 ± 0.40 (.063 ± .016)

5P2236 1309108 6V3263 1309109 1309110 1309110

15

Hydraulic Cylinders and Seals SEAL SELECTION FOR OTHER THAN CATERPILLAR EQUIPMENT

Seal Selection for Other Than Caterpillar Equipment Caterpillar seals can be used on other than Caterpillar equipment. The following section will help you identify which seal is necessary for your repair.

How to Select the Correct Seals: •

For cylinders used on other than Caterpillar equipment, measure the components using the following procedure.To find the correct replacement seal size, the seal groove dimensions in the iron itself should always be measured. Measuring a used seal can give false dimensions due to distortion in size from wear. The hydraulic cylinder illustration below calls out the iron dimensions required to identify the proper size replacement seal.

Diameter of Rod (R) Seal Type or Cylinder Bore (B) Rod Wiper: R Rod Seal: R Buffer Seal R Head Wear Ring: R Head Seal: B Piston Seal: B Piston Wear Ring: B

Groove Width A D F H J L N

Groove Diameter C E G I K M O

Should seal replacement be requested by a customer over-the-counter rather than through the service shop, measure the seal’s outside diameter at four equally-spaced areas around the seal. Take the average of these measurements to determine the seal’s outside diameter. Repeat this procedure with the seal’s inside diameter and width (height) to determine seal replacement size. Use the tables in the following sections to find the right seal for your customer’s repair.

16

Hydraulic Cylinders and Seals PRESS-IN WIPER SEALS

PRESS-IN WIPER SEALS

ROD DIAMETER (in) (mm) 1.00 1.18 1.25

25.40 30.00 31.75

1.37 1.38 1.50

34.92 35.00 38.10

1.57 1.75

40.00 44.45

1.77

45.00

1.83 1.87 1.88 1.89 2.00

46.50 47.62 47.63 47.90 50.80

2.13

53.98

2.22 2.25

56.50 57.15

2.36 2.37 2.50

59.85 60.32 63.50

2.56 2.63

65.00 66.68

SEAL TYPE

PART NUMBER 7K-1864 144-9480 2H-1746 3E-4160 4J-8982 3E-4159 140-2392 3E-4161 9J-4037 226-8202 144-9492 3E-4162 7J-6932 8J-5817 231-3539 141-0713 233-0617 099-3929 4T-6777 227-1143 116-3393 3E-4164 7J-8277 229-9382 227-1145 4T-6125 096-1884 5J-3937 3E-4165 7J-8278 231-3538 5H-1513 093-1433 231-3540 3E-4166 7J-8273 225-3281 227-1148 227-1146

URE URE NIT URE URE URE URE URE NIT URE URE URE URE NIT URE URE URE URE URE URE URE URE NIT URE URE URE URE URE URE NIT URE URE URE URE URE NIT URE URE URE

D A A A A D A A B D A A B D B A A B A A A B B A A A A A B A F B A A B B B

A GROOVE WIDTH (± .02 in) (in) (mm)

B GROOVE DIA. (in) (mm)

0.31 0.39 0.28 0.31 0.34 0.31 0.39 0.31 0.43 0.43 0.39 0.31 0.31 0.43 0.43 0.28 0.33 0.33 0.43 0.43 0.33 0.31 0.43 0.43 0.43 0.43 0.33 0.29 0.31 0.43 0.43 0.51 0.16 0.43 0.31 0.43 0.43 0.43 0.43

1.50 1.58 1.75 1.75 1.75 1.88 1.77 2.00 2.25 2.25 1.97 2.25 2.25 2.44 2.44 2.16 2.32 2.52 2.56 2.56 2.52 2.50 2.69 2.69 2.88 2.88 2.91 3.13 2.75 3.00 3.00 3.25 2.96 3.12 3.00 3.25 3.25 3.31 3.37

7.92 10.00 7.00 7.92 8.60 7.92 10.00 7.92 11.00 11.00 10.00 7.92 7.94 11.00 11.00 7.00 8.50 8.35 11.00 11.00 8.35 7.92 11.00 11.00 11.00 11.00 8.35 7.35 7.92 11.00 11.00 12.83 4.15 11.00 7.92 11.00 11.00 11.00 11.00

38.20 40.02 44.50 44.45 44.50 47.63 45.02 50.80 57.15 57.15 50.02 57.15 57.25 61.90 61.90 54.97 59.05 64.02 65.07 65.07 64.02 63.50 68.23 68.23 73.03 73.03 74.02 79.38 69.85 76.13 76.13 82.55 75.12 79.35 76.20 82.55 82.55 84.02 85.72

17

Hydraulic Cylinders and Seals PRESS-IN WIPER SEALS

PRESS-IN WIPER SEALS

ROD DIAMETER (in) (mm)

18

2.75

69.80

2.76 3.00

70.00 76.20

3.06 3.14 3.25

77.70 79.85 82.55

3.26 3.35

82.70 85.00

3.41 3.50

86.50 88.90

3.54

90.00

3.65 3.74

92.70 95.00

3.75

95.20

3.80 3.94 4.00

96.50 100.00 101.55

4.04 4.13

102.50 105.00

4.23 4.25

107.50 107.95

SEAL TYPE

PART NUMBER 149-1488 3E-4168 7J-8274 225-3283 167-2451 3E-4170 8J-0249 225-3284 165-9285 096-0854 3E-4173 7J-7732 225-3285 165-9286 167-2470 121-1611 093-1441 3E-4176 7J-8276 225-3286 126-1885 094-0723 165-9288 167-2477 167-2476 227-1149 9J-1325 8J-6069 096-0059 133-6904 138-9740 3E-4177 2D-8540 225-3287 133-6813 165-9290 2U-5368 133-6814 225-3288

URE URE NIT URE URE URE NIT URE URE URE URE NIT URE URE URE URE URE URE NIT URE URE URE URE URE URE URE NIT URE URE URE URE URE NIT URE URE URE URE URE

C A A B E A A B B F A A B B E B A A A B B D B E E B A A A B A A A B B B A B B

A GROOVE WIDTH (± .02 in) (in) (mm)

B GROOVE DIA. (in) (mm)

0.55 0.31 0.55 0.55 0.31 0.31 0.55 0.55 0.43 0.16 0.31 0.55 0.55 0.43 0.33 0.51 0.33 0.31 0.55 0.55 0.51 0.53 0.43 0.32 0.33 0.55 0.55 0.55 0.33 0.51 0.31 0.31 0.50 0.55 0.37 0.47 0.47 0.47 0.55

3.76 3.25 3.75 3.75 3.31 3.50 4.00 4.00 3.71 3.75 3.88 4.25 4.25 3.91 3.90 3.90 4.10 4.13 4.50 4.50 4.09 4.09 4.30 4.29 4.29 4.75 4.75 4.75 4.49 4.49 4.50 4.63 5.00 5.00 4.77 4.77 5.12 4.97 5.25

14.00 7.92 14.00 14.00 8.00 7.92 14.00 14.00 11.00 4.15 7.92 14.00 14.00 11.00 8.50 13.00 8.35 7.92 14.00 14.00 13.00 13.50 11.00 8.20 8.50 14.00 14.00 14.00 8.35 13.00 8.00 7.92 12.70 14.00 9.30 12.00 12.00 12.00 14.00

95.49 82.55 95.27 95.27 84.02 88.90 101.67 101.67 94.23 95.15 98.43 107.95 107.95 99.23 99.03 99.00 104.02 104.78 114.32 114.32 104.00 104.00 109.23 109.03 109.03 120.65 120.65 120.65 114.02 114.00 114.24 117.48 127.10 127.00 121.26 121.26 130.00 126.26 133.35

Hydraulic Cylinders and Seals PRESS-IN WIPER SEALS

PRESS-IN WIPER SEALS

ROD DIAMETER (in) (mm) 4.25 4.33 4.50

107.95 110.00 114.30

4.75

120.60

4.82 4.90 5.00

122.50 124.50 127.00

5.12 5.25 5.50 5.51

130.00 133.30 139.70 140.00

5.75

146.05

5.91 6.00

150.00 152.40

6.50 6.75 7.00

165.10 171.40 177.80

7.25 7.50 8.00 8.75 9.00 11.00 12.50 13.50 15.75

184.15 190.50 203.20 222.25 228.60 279.40 317.50 342.90 400.05

PART NUMBER 9J-1333 165-9291 3E-4178 225-3289 9J-1337 227-1150 9J-1341 165-9292 121-1596 225-3290 9J-1681 165-9293 233-0632 225-3291 167-2494 165-9294 225-3293 9X-3574 9J-5473 9J-5469 165-9296 225-3294 9J-1697 225-3295 227-1147 9X-7333 3G-2646 225-3296 225-3297 225-3298 225-3299 225-3300 9X-7354 9X-7353 9X-7352 9X-7350 149-2697

A GROOVE WIDTH (± .02 in) (in) (mm)

SEAL TYPE NIT URE URE URE NIT URE NIT URE URE URE NIT URE URE URE URE URE URE URE NIT URE URE URE NIT URE URE URE NIT URE URE URE URE URE URE URE URE URE URE

A B A B A B A B A B A B B B E B B B A A B B A B B A A B B B B B A A A A B

0.55 0.47 0.31 0.55 0.55 0.55 0.55 0.47 0.39 0.55 0.55 0.47 0.55 0.55 0.41 0.51 0.54 0.55 0.55 0.55 0.51 0.54 0.55 0.54 0.55 0.55 0.55 0.59 0.54 0.54 0.54 0.54 0.59 0.59 0.59 0.59 0.55

14.00 12.00 7.92 14.00 14.00 14.00 14.00 12.00 10.02 14.00 14.00 12.00 14.00 14.00 10.35 13.00 13.70 14.00 14.00 14.00 13.00 13.70 14.00 13.70 14.00 14.00 14.00 15.00 13.70 13.70 13.70 13.70 15.00 15.00 15.00 15.00 14.00

B GROOVE DIA. (in) (mm) 5.25 4.97 5.13 5.50 5.50 5.75 5.75 5.56 5.64 6.00 6.00 5.76 6.25 6.50 6.30 6.31 6.75 6.75 6.75 6.75 6.70 7.00 7.00 7.50 7.75 8.00 8.00 8.00 8.25 8.50 9.00 9.75 9.75 12.00 13.50 14.50 16.76

133.35 126.26 130.18 139.70 139.70 146.13 146.05 141.26 143.14 152.40 152.40 146.26 158.75 165.10 160.02 160.26 171.45 171.45 171.45 171.45 170.26 177.80 177.80 190.50 196.85 203.20 203.20 203.20 209.45 215.90 228.60 247.65 247.70 304.85 342.95 368.35 425.82

19

Hydraulic Cylinders and Seals SNAP-IN WIPER SEALS

SNAP-IN WIPER SEALS

ROD DIAMETER (in) (mm) 0.63 0.75 1.00

15.88 19.05 25.40

1.13 1.25

28.58 31.75

1.38 1.50

34.93 38.10

1.63

41.28

1.75

44.40

1.97

20

50.00

2.00

50.80

2.01 2.25

50.96 57.15

2.37 2.38 2.50

60.32 60.33 63.50

PART NUMBER

SEAL TYPE

5J-2274 6J-1879 6J-1890 3E-4124 3E-4138 3E-4139 3E-4125 3E-4140 141-7451 3E-4103 3E-4141 5J-6795 3E-4126 3E-4104 3E-4163 8T-5431 7U-7648 3E-4105 3E-4150 3E-4142 3E-4127 5U-3693 3E-4151 3E-4143 3E-4106 3E-4128 4T-0415 1K-5354 3E-4107 3E-4152 3E-4144 6J-0217 3E-4129 5J-8016 3E-4167 3E-4108 3E-4153 3E-4145

REG REG REG K SHU SHU K SHU H AN SHU REG K AN SHU REG REG AN H SHU K REG H SHU AN K REG REG AN H SHU REG K REG SHU AN H SHU

A GROOVE WIDTH (± .002 in) (in) (mm) 0.13 0.19 0.19 0.19 0.19 0.19 0.19 0.19 0.34 0.11 0.19 0.19 0.19 0.11 0.19 0.19

3.20 4.80 4.80 4.95 4.75 4.75 4.95 4.75 8.76 2.72 4.75 4.80 4.95 2.72 4.75 4.80

0.11 0.22 0.19 0.19 0.25 0.22 0.25 0.11 0.19 0.25 0.18 0.11 0.28 0.25 0.25 0.26 0.25 0.25 0.11 0.28 0.25

2.72 5.54 4.75 4.95 6.35 5.54 6.32 2.72 4.95 6.38 4.68 2.72 7.14 6.32 6.38 6.48 6.38 6.32 2.72 7.14 6.32

B GROOVE BORE DIA. (± .003 in) (in) (mm) 0.88 1.13 1.38 1.39 1.50 1.62 1.64 1.75

22.28 28.63 34.98 35.18 38.02 41.20 41.53 44.37

1.80 1.87 1.88 1.89 1.93 2.00

45.77 47.55 47.68 47.88 48.95 50.72

2.13 2.05 2.11 2.12 2.14

54.00 52.12 53.72 53.90 54.23

2.36 2.50 2.30 2.39 2.50

60.07 63.42 58.47 60.58 63.55

2.55 2.74 2.75 2.75 2.76 2.88 2.87 2.80 2.99 3.00

64.82 69.72 69.77 69.90 70.10 73.08 72.95 71.17 76.07 76.12

C SEAL GROOVE DIA. (± .010 in) (in) (mm) 0.79 1.00 1.25 1.08 1.37 1.49 1.33 1.62 2.00 1.67 1.74 1.75 1.58 1.79 1.74 2.13

20.10 25.40 31.75 27.48 34.80 37.97 33.83 41.15 50.80 42.37 44.32 44.45 40.18 45.54 44.32 54.03

1.92 1.89 1.99 1.83 2.50 2.14 2.33 2.18 2.08 2.33 2.37 2.43 2.39 2.58 2.58 2.41 2.71 2.70 2.68 2.64 2.83

48.72 47.88 50.67 46.53 63.50 54.23 59.11 55.32 52.88 59.25 60.25 61.67 60.58 65.46 65.60 61.14 68.78 68.63 68.02 66.93 71.81

Hydraulic Cylinders and Seals SNAP-IN WIPER SEALS

SNAP-IN WIPER SEALS

ROD DIAMETER (in) (mm) 2.50

63.50

2.63 2.75

66.68 69.85

3.00

76.20

3.25 3.38

82.55 85.73

3.50

88.90

3.75

95.25

4.00

101.55

4.25

107.95

4.50

114.30

4.75 5.00

120.65 127.00

PART NUMBER

SEAL TYPE

5J-8156 3E-4130 3E-4131 3E-4109 3E-4169 5J-7036 3E-4132 3E-4110 3E-4154 3E-4146 5J-7030 3E-4133 5J-7034 3E-4171 3E-4111 3E-4112 3E-4155 3E-4147 5U-3529 5J-7032 3E-4134 3E-4113 3E-4172 138-9739 3E-4114 3E-4156 3E-4148 3E-4135 3E-4115 7U-4138 3E-4116 3E-4157 3E-4136 3G-8505 3E-4117 3E-4118 3E-4158 3E-4137

REG K K AN SHU REG K AN H SHU REG K REG SHU AN AN H SHU REG REG K AN SHU REG AN H SHU K AN REG AN H K REG AN AN H K

A GROOVE WIDTH (± .002 in) (in) (mm) 0.25 0.26 0.26 0.12 0.25 0.25 0.26 0.12 0.28 0.25 0.25 0.26 0.25 0.25 0.12 0.12 0.28 0.25 0.25 0.25 0.26 0.12 0.25 0.25 0.14 0.28 0.25 0.26 0.14 0.25 0.14 0.28 0.26 0.38 0.14 0.14 0.28 0.26

6.38 6.48 6.48 3.10 6.32 6.38 6.48 3.10 7.14 6.32 6.38 6.48 6.38 6.32 3.10 3.10 7.14 6.32 6.30 6.38 6.48 3.10 6.32 6.37 3.51 7.14 6.32 6.48 3.51 6.30 3.51 7.14 6.48 9.55 3.51 3.51 7.14 6.48

B GROOVE BORE DIA. (± .003 in) (in) (mm) 3.00 3.01 3.14 3.11 3.25 3.25 3.26 3.36 3.49 3.50 3.50 3.51 3.75 3.87 3.74 3.86 3.99 4.00 4.00 4.00 4.01 4.11 4.25

76.25 76.45 79.63 79.10 82.47 82.60 82.80 85.45 88.77 88.82 88.95 89.15 95.30 98.35 94.97 98.15 101.47 101.52 101.60 101.65 101.85 104.50 107.87

4.43 4.49 4.50 4.51 4.68 4.75 4.93 4.99 5.01 5.25 5.18 5.43 5.49 5.51

112.45 114.17 114.22 114.55 118.80 120.65 125.15 126.87 127.25 133.40 131.50 137.85 139.57 139.95

C SEAL GROOVE DIA. (± .010 in) (in) (mm) 2.83 2.66 2.78 2.96 3.08 3.08 2.91 3.21 3.13 3.33 3.33 3.16 3.58 3.70 3.58 3.71 3.64 3.83

71.95 67.49 70.66 75.16 78.16 78.30 73.84 81.51 79.53 84.51 84.65 80.19 91.00 94.03 91.03 94.21 92.33 97.21

3.83 3.66 3.96 4.08 4.50 4.24 4.14 4.33 4.16 4.49

97.35 92.89 100.56 103.56 114.30 107.70 105.03 109.91 105.59 114.05

4.74 4.64 4.66 5.00 4.99 5.24 5.14 5.16

120.40 117.73 118.29 127.00 126.75 133.10 130.43 130.99

21

Hydraulic Cylinders and Seals SNAP-IN WIPER SEALS

SNAP-IN WIPER SEALS

ROD DIAMETER (in) (mm)

22

5.00

127.00

5.25

133.35

5.50 5.75

139.70 146.05

6.00

152.40

6.13 6.50

155.58 165.10

6.75 7.00

171.45 177.80

7.25 7.50 7.75 8.50 8.75 9.00

184.15 190.50 196.80 215.90 222.25 228.60

10.50 11.00

266.70 279.40

11.50 12.50

292.05 317.50

PART NUMBER

SEAL TYPE

3E-4149 9J-2547 3E-4119 4T-5663 3E-4174 6J-3073 3E-4120 3E-4121 1U-2708 7J-3319 3E-4122 6J-0542 3E-4123 9X-7366 5J-2682 4T-4802 7J-3320 121-4172 8J-9934 6E-0252 9X-7367 6J-7694 4T-4805 9X-7368 1U-4625 121-4171 9X-7369 4T-4130

SHU REG AN REG SHU REG AN AN REG REG AN REG AN REG REG REG REG SHU REG REG SHU REG REG SHU REG SHU SHU REG

A GROOVE WIDTH (± .002 in) (in) (mm) 0.37 0.38 0.14 0.38 0.37 0.38 0.15 0.15 0.38 0.38 0.15 0.40 0.15 0.40 0.40 0.38 0.40 0.40 0.40 0.38 0.40 0.40 0.50 0.50 0.50 0.50 0.50 0.50

9.50 9.55 3.51 9.55 9.50 9.55 3.91 3.91 9.55 9.55 3.91 10.20 3.91 10.19 10.20 9.55 10.20 10.20 10.20 9.55 10.20 10.20 12.75 12.75 12.75 12.75 12.75 12.75

B GROOVE BORE DIA. (± .003 in) (in) (mm) 5.75 5.75 5.68 6.00 6.25 6.13 6.24 6.49 6.75 6.88 6.99 7.50 7.24

145.97 146.10 144.20 152.45 158.67 155.63 158.47 164.82 171.50 174.68 177.52 190.55 183.87

8.00 8.00 8.50 8.50 9.25 9.50 9.75 9.75 11.50 12.00 12.00 12.50 13.50 13.50

203.25 203.25 215.95 215.95 235.00 241.35 247.70 247.70 292.15 304.85 304.85 317.55 342.95 342.95

C SEAL GROOVE DIA. (± .010 in) (in) (mm) 5.49 5.50 5.49 5.75 5.99 5.87 6.02 6.27 6.50 6.63 6.77 7.17 7.02 8.00 7.67 7.75 8.17 8.25 9.00 9.25 9.50 9.50 11.17 11.67 11.67 12.17 13.17 13.17

139.52 139.70 139.45 146.05 152.22 149.20 152.96 159.31 165.10 168.28 172.01 182.00 178.36 203.20 194.70 196.85 207.40 209.55 228.60 234.95 241.30 241.35 283.60 296.30 296.30 309.00 334.40 334.40

Hydraulic Cylinders and Seals U-CUP SEALS

U-CUP SEALS

ROD DIAMETER (in) (mm) 0.37 0.63 0.75 1.00 1.13

9.52 15.88 19.05 25.40 28.58

1.18 1.25

30.00 31.75

1.38

34.93

1.50

38.10

1.63

41.28

1.75

44.45

1.77

44.95

1.88 2.00

47.63 50.80

PART NUMBER 1U-3147 7J-0375 6J-1878 6J-1889 3E-4175 3E-4284 144-9481 3E-4181 3E-4180 167-2295 3E-4193 3E-4182 3E-4283 3E-4194 140-2377 3E-4183 9J-4038 167-2294 3E-4195 3E-4215 3E-4184 3E-4201 4T-0488 3E-4185 8J-5816 167-2443 167-2300 3E-4287 3E-4216 143-8914 167-2297 167-2302 3E-4186 5U-3644 3E-4196 9J-1318 167-2304 3G-3259 3E-4217

A B GROOVE WIDTH GROOVE DIA. (+.015, -.000 in) (+.002, -.000 in) (in) (mm) (in) (mm)

SEAL TYPE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE NIT URE URE URE URE URE URE URE NIT URE URE URE URE URE URE URE URE URE URE NIT URE URE URE

A A A A E E A E D A E E D E A E B A E E E D A E B E A E E A A A E D E B A A E

0.16 0.29 0.29 0.29 0.34 0.41 0.43 0.34 0.34 0.29 0.41 0.34 0.34 0.41 0.43 0.41 0.29 0.29 0.41 0.55 0.41 0.41 0.35 0.41 0.29 0.29 0.29 0.41 0.55 0.43 0.29 0.35 0.41 0.38 0.41 0.41 0.41 0.41 0.55

4.10 7.26 7.26 7.26 8.74 10.49 11.00 8.74 8.74 7.26 10.49 8.74 8.74 10.49 11.00 10.49 7.26 7.26 10.49 13.97 10.49 10.49 8.85 10.49 7.26 7.26 7.26 10.49 13.97 11.00 7.26 8.85 10.49 9.53 10.49 10.49 10.49 10.50 13.97

0.63 0.88 1.00 1.25 1.50 1.63 1.57 1.63 1.63 1.63 1.75 1.75 1.75 1.88 1.77 1.88 1.88 1.88 2.00 2.13 2.00 2.00 2.00 2.13 2.13 2.13 2.13 2.25 2.38 2.36 2.15 2.25 2.38 2.50 2.50 2.50 2.50 2.50 2.63

16.00 22.28 25.45 31.80 38.10 41.28 40.00 41.28 41.28 41.33 44.45 44.45 44.45 47.63 45.05 47.63 47.68 47.68 50.80 53.98 50.80 50.80 50.85 53.98 54.03 54.03 54.03 57.15 60.33 60.00 54.58 57.20 60.33 63.50 63.50 63.55 63.55 63.55 66.68

CROSS SECTION BACK-UP (in) (mm) RING

0.19 0.25 0.20 0.19 0.19

4.76 6.35 5.00 4.76 4.76

0.25 0.19 0.19 0.25

6.35 4.76 4.76 6.35

0.19

4.76

0.25 0.31 0.19 0.19

6.35 7.94 4.76 4.76

0.19

4.76

0.25 0.31

6.35 7.94

0.19 0.25 0.25

4.76 6.40 6.35

0.31

7.94

23

Hydraulic Cylinders and Seals U-CUP SEALS

U-CUP SEALS

ROD DIAMETER (in) (mm) 2.00 2.13 2.17 2.25

24

50.80 53.98 55.00 57.15

2.36 2.37 2.38

60.00 60.32 60.33

2.50

63.50

2.56

65.00

2.63 2.75

66.68 69.85

2.76

70.00

2.95

75.00

3.00

76.20

PART NUMBER 3E-4227 167-2305 167-2306 3E-4187 3E-4197 7J-4820 167-2307 3E-4218 3E-4228 093-1475 167-2310 3E-4204 3E-4188 3G-2911 3E-4189 3E-4198 7J-4824 3G-3752 167-2312 3E-4285 3E-4219 167-2313 3E-4229 167-2314 093-1476 167-2315 3E-4199 9J-2944 6E-1459 167-2317 3E-4220 3E-4230 167-2299 093-1477 096-3468 167-2318 3E-4190 3E-4200 8J-0248

A B GROOVE WIDTH GROOVE DIA. (+.015, -.000 in) (+.002, -.000 in) (in) (mm) (in) (mm)

SEAL TYPE URE URE URE URE URE NIT URE URE URE URE URE URE URE URE URE URE NIT URE URE URE URE URE URE URE URE URE URE NIT URE URE URE URE URE URE URE URE URE URE NIT

E A A E E B A E E C A D E A E E B A A D E A E A C A E B E A E E A C C A E E B

0.69 0.41 0.56 0.41 0.41 0.41 0.41 0.55 0.69 0.56 0.41 0.41 0.41 0.41 0.41 0.41 0.41 0.41 0.41 0.55 0.55 0.54 0.69 0.41 0.56 0.41 0.41 0.41 0.41 0.41 0.55 0.69 0.56 0.56 0.56 0.52 0.41 0.41 0.41

17.48 10.49 14.10 10.49 10.49 10.49 10.49 13.97 17.48 14.10 10.49 10.49 10.49 10.50 10.49 10.49 10.49 10.49 10.50 13.97 13.97 13.70 17.48 10.49 14.10 10.49 10.49 10.49 10.49 10.49 13.97 17.48 14.10 14.10 14.10 13.15 10.49 10.49 10.49

2.75 2.63 2.68 2.63 2.75 2.75 2.75 2.88 3.00 2.87 2.88 2.75 2.75 2.88 2.88 3.00 3.00 3.00 3.00 3.13 3.13 3.13 3.25 3.06 3.07 3.13 3.25 3.25 3.25 3.25 3.38 3.50 3.27 3.27 3.47 3.55 3.38 3.50 3.50

69.85 66.73 68.03 66.68 69.85 69.90 69.90 73.03 76.20 73.02 73.08 69.85 69.86 73.08 73.03 76.20 76.25 76.25 76.25 79.38 79.38 79.50 82.55 77.75 78.02 79.43 82.55 82.60 82.60 82.60 85.73 88.90 83.03 83.03 88.03 90.05 85.73 88.90 88.95

CROSS SECTION BACK-UP (in) (mm) RING 0.38

9.53

0.19 0.25

4.76 6.35

0.31 0.38

7.94 9.53 093-1518

0.19 0.19

4.76 4.76

0.19 0.25

4.76 6.35

0.31 0.31

7.94 7.94

0.38

9.53 096-1055

0.25

6.35

0.38

9.65

0.31 0.38

7.94 9.53 093-1519 096-3467

0.19 0.25

4.76 6.35

Hydraulic Cylinders and Seals U-CUP SEALS

U-CUP SEALS

ROD DIAMETER (in) (mm) 3.00

76.20

3.15

80.00

3.25

82.55

3.35

85.00

3.38

85.73

3.50

88.90

3.54

90.00

3.74

95.00

3.75

95.25

3.94

4.00

4.13 4.25

100.00

101.60

105.00 107.95

PART NUMBER 167-2319 3E-4221 3E-4231 167-2343 093-1479 7J-2145 167-2320 096-1567 167-2322 3E-4286 3E-4222 3E-4191 3E-4202 7J-2150 167-2324 3E-4223 3E-4232 104-9658 105-2577 167-2325 150-5826 167-2327 3E-4192 3E-4203 9J-1328 167-2328 3E-4224 121-1371 8U-6849 167-2330 096-2664 167-2329 3E-4225 167-2331 2U-9113 3E-4233 167-2332 3E-4205 9J-1336

A B GROOVE WIDTH GROOVE DIA. (+.015, -.000 in) (+.002, -.000 in) (in) (mm) (in) (mm)

SEAL TYPE URE URE URE URE URE NIT URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE

A E E A C B A A A D E E E B A E E A A A C A E E B A E A A A C A E A A E A E B

0.41 0.55 0.69 0.35 0.56 0.41 0.41

10.49 13.97 17.48 8.85 14.10 10.49 10.49

3.50 3.63 3.75 3.53 3.66 3.75 3.75

88.95 92.08 95.25 89.58 93.03 95.30 95.30

0.56 0.55 0.55 0.41 0.41 0.41 0.41 0.55 0.69 0.39

14.10 13.97 13.97 10.49 10.49 10.49 10.49 13.97 17.48 10.00

3.94 4.00 4.00 3.88 4.00 4.00 4.00 4.13 4.25 4.29

100.03 101.60 101.60 98.43 101.60 101.65 101.65 104.78 107.95 108.90

0.44 0.35 0.56 0.41 0.41 0.41 0.41 0.55 0.35 0.51 0.56 0.56 0.51 0.62 0.41 0.39 0.69 0.56 0.62 0.66

11.10 9.00 14.10 10.49 10.49 10.49 10.49 13.97 9.00 13.00 14.10 14.10 13.00 15.72 10.49 10.00 17.48 14.10 15.72 16.84

4.14 4.33 4.33 4.13 4.25 4.25 4.25 4.38 4.53 4.53 4.53 4.53 4.72 4.63 4.63 4.72 4.75 4.73 4.75 5.00

105.03 110.00 110.03 104.78 107.95 108.00 108.00 111.13 115.00 115.00 115.03 115.03 120.00 117.48 117.53 120.00 120.65 120.03 120.65 127.05

CROSS SECTION BACK-UP (in) (mm) RING 0.31 0.38

7.94 9.53 096-1054

0.31 0.31 0.19 0.25

7.94 7.94 4.76 6.35

0.31 0.38 0.39

7.94 9.53 10.00

150-5827 0.19 0.25

4.76 6.35

0.31

7.94

0.30

7.50 096-2655

0.31

7.94

0.36 0.38

9.20 9.53

0.25

6.35

25

Hydraulic Cylinders and Seals U-CUP SEALS

U-CUP SEALS

ROD DIAMETER (in) (mm) 4.25 4.33

4.37 4.50

26

107.95 110.00

111.12 114.30

4.75

120.65

5.00

126.95

5.12 5.25

130.00 133.30

5.50

139.70

5.51 5.71 5.75

140.00 145.00 146.00

5.91 6.00

150.00 152.40

6.25 6.50

158.75 165.10

PART NUMBER 167-2333 167-2334 128-9270 167-2338 3G-5054 6U-9505 3E-4206 9J-1340 167-2336 3E-4234 3E-4207 9J-1344 167-2337 121-1594 3E-4208 3E-4226 3E-4235 9J-1684 167-2339 167-2341 167-2342 3E-4209 3E-4210 167-2938 167-2344 3E-4236 167-2428 167-2347 121-1602 9J-5470 167-2345 167-2429 3E-4211 3E-4237 167-2421 167-2346 167-2348 3E-4212 3E-4238

A B GROOVE WIDTH GROOVE DIA. (+.015, -.000 in) (+.002, -.000 in) (in) (mm) (in) (mm)

SEAL TYPE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE

A A C A A B D B A E D B A C D E E B A A A D D E A E E A D B A E D E B A A D E

0.66 0.56 0.56 0.61 0.54 0.42 0.62 0.41 0.41 0.69 0.62 0.66 0.66 0.38 0.62 0.69 0.69 0.66 0.66 0.56 0.66 0.62 0.62 0.41 0.41 0.69 0.55 0.55 0.56 0.66 0.66 0.55 0.62 0.69 0.54 0.54 0.54 0.62 0.69

16.84 14.10 14.10 15.50 13.61 10.62 15.72 10.50 10.49 17.48 15.72 16.84 16.84 9.53 15.72 17.48 17.48 16.84 16.84 14.10 16.84 15.72 15.72 10.49 10.49 17.48 14.00 14.00 14.10 16.84 16.84 14.00 15.72 17.48 13.65 13.65 13.61 15.72 17.48

5.00 4.92 4.92 5.12 5.13 4.00 5.00 5.13 5.13 5.25 5.25 5.50 5.50 5.60 5.50 5.63 5.75 5.75 5.75 5.71 6.00 5.75 6.00 6.13 6.13 6.25 6.10 6.30 6.34 6.50 6.50 6.50 6.50 6.75 6.75 6.75 6.75 7.00 7.25

127.05 125.03 125.03 130.05 130.23 101.57 127.00 130.22 130.23 133.35 133.35 139.75 139.75 142.13 139.70 142.88 146.05 146.10 146.10 145.03 152.45 146.05 152.40 155.63 155.63 158.75 155.00 160.03 161.16 165.15 165.15 165.00 165.10 171.45 171.50 171.50 171.50 177.80 184.15

CROSS SECTION BACK-UP (in) (mm) RING

7Y-4941

0.50 0.25

12.76 6.35

0.38 0.25

9.53 6.35

0.25 0.31 0.38

6.35 7.94 9.53

0.25 0.25

6.35 6.35

0.38

9.53

0.25 0.38

6.35 9.53

0.25 0.38

6.35 9.53

121-1595

Hydraulic Cylinders and Seals U-CUP SEALS

U-CUP SEALS

ROD DIAMETER (in) (mm) 6.50

165.10

6.75 7.00

171.45 177.80

7.25

184.15

7.50

190.50

8.00

203.20

8.75

222.25

9.00 11.00 11.04 12.50 13.50 15.75

228.50 279.30 280.31 317.40 342.90 399.98

PART NUMBER 167-2415 167-2349 167-2351 3E-4213 9X-7450 3E-4239 167-2416 3G-2649 167-2352 167-2417 167-2353 3E-4240 167-2418 167-2355 3E-4214 167-2354 167-2419 167-2356 9X-7334 9X-7389 8C-9157 9X-7388 167-2435 149-0814

A B GROOVE WIDTH GROOVE DIA. (+.015, -.000 in) (+.002, -.000 in) (in) (mm) (in) (mm)

SEAL TYPE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE URE NIT URE URE URE

B A A D D D B B A B A E B A E E B A D D B D E A

0.54 0.66 0.41 0.62 0.41 0.69 0.54 0.54 0.54 0.54 0.54 0.69 0.54 0.54 0.62 0.54 0.54 0.54 0.41 0.41 0.64 0.41 0.41 0.41

13.61 16.80 10.49 15.72 10.50 17.48 13.61 13.61 13.61 13.65 13.65 17.48 13.61 13.61 15.72 13.65 13.65 13.65 10.50 10.50 16.13 10.50 10.50 10.50

7.25 7.25 7.25 7.50 7.68 7.75 7.75 7.75 7.75 8.00 8.00 8.25 8.25 8.25 8.50 8.75 9.50 9.50 9.68 0.41 11.81 13.18 14.18 16.43

184.20 184.20 184.20 190.50 195.02 196.85 196.90 196.90 196.90 203.25 203.25 209.55 209.60 209.60 215.90 222.30 241.35 241.35 245.82 10.50 300.10 334.72 360.12 417.27

CROSS SECTION BACK-UP (in) (mm) RING

0.25

6.35

0.38

9.53

0.38

9.53

0.25

6.35

0.34

8.65

27

Hydraulic Cylinders and Seals BUFFER SEALS

BUFFER SEALS

ROD DIAMETER (in) (mm)

28

1.25 1.38

31.75 34.95

1.50 1.75

38.10 44.45

1.77 1.88 2.00 2.13

44.95 47.63 50.80 53.98

2.17 2.25 2.37 2.50 2.56 2.75 3.00

55.00 57.15 60.32 63.50 65.00 69.85 76.20

3.25 3.31 3.35 3.50 3.54 3.63 3.74

82.55 84.00 85.00 88.90 90.00 92.08 95.00

3.75 3.94 4.00 4.13 4.25 4.33

95.25 100.00 101.60 105.00 107.95 110.00

4.50 4.75 4.88 5.00

114.30 120.65 124.00 127.00

PART NUMBER

SEAL TYPE

9J-3497 141-0706 140-2310 167-2186 167-2190 167-2191 143-8915 167-2192 167-2195 167-2198 167-2197 167-2199 167-2200 167-2202 167-2201 167-2204 167-2207 152-9022 167-2208 167-2209 123-1943 167-2210 167-2211 167-2212 3G-1259 150-5885 167-2213 167-2214 167-2215 167-2216 167-2217 167-2218 128-9266 167-2219 167-2220 167-2221 155-9191 121-1593 167-2222

A C C D D D C D D D D D D D D D D C D D C D D D A C D D D D D D C D D D C C D

A GROOVE WIDTH (± .005 in) (in) (mm)

B GROOVE DIA. (± .005 in) (in) (mm)

1.78 1.99 1.99 2.03 2.28 2.39 2.38 2.25 2.53 2.63 2.77 2.78 2.89 3.02 3.14 3.20 3.39 3.64 3.64 3.89 3.96 3.96 4.14 4.16 4.27 4.35 4.35 4.39 4.55 4.64 4.75 5.23 4.94 4.94 5.48 5.73 5.53 5.63 5.96

0.14 0.25 0.25 0.14 0.14 0.22 0.27 0.14 0.14 0.14 0.22 0.25 0.22 0.22 0.22 0.22 0.22 0.22 0.22 0.22 0.25 0.25 0.22 0.25 0.22 0.25 0.25 0.22 0.25 0.22 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25

45.29 50.50 50.50 51.64 57.99 60.73 60.50 57.20 64.34 66.73 70.26 70.52 73.43 76.61 79.78 81.28 86.13 92.48 92.48 98.83 100.53 100.53 105.18 105.54 108.36 110.54 110.54 111.53 115.53 117.88 120.53 132.72 125.53 125.54 139.07 145.42 140.53 142.88 151.38

3.56 6.40 6.40 3.56 3.56 5.60 6.75 3.56 3.56 3.56 5.60 6.40 5.59 5.59 5.59 5.59 5.59 5.58 5.59 5.59 6.40 6.40 5.59 6.40 5.59 6.40 6.40 5.59 6.40 5.59 6.40 6.35 6.40 6.40 6.35 6.35 6.40 6.40 6.35

Hydraulic Cylinders and Seals BUFFER SEALS

BUFFER SEALS

ROD DIAMETER (in) (mm) 5.12 5.25

130.00 133.35

5.50

139.70

5.51 5.71 5.75 5.91 6.00 6.50 6.75 7.00 7.25 7.50 8.00 8.75

140.00 145.00 146.05 150.00 152.40 165.10 171.45 177.80 184.15 190.50 203.20 222.25

PART NUMBER

SEAL TYPE

167-2223 4T-5717 167-2224 167-2725 167-2225 167-2226 167-2231 167-2227 167-2229 167-2228 167-2230 167-2232 167-2233 167-2234 167-2236 167-2239 167-2240

D A D D D D D D D D D D D D D D D

A GROOVE WIDTH (± .005 in) (in) (mm)

B GROOVE DIA. (± .005 in) (in) (mm)

5.73 6.21 6.21 6.12 6.12 6.12 6.32 6.73 6.52 6.62 7.50 7.69 7.94 8.08 8.33 8.83 9.58

0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.32 0.32 0.32 0.32

145.53 157.73 157.73 155.35 155.35 155.50 160.53 170.82 165.50 168.10 190.55 195.45 201.80 205.30 211.65 224.35 243.40

6.40 6.35 6.35 6.35 6.35 6.30 6.40 6.35 6.30 6.35 6.35 6.35 6.35 8.25 8.25 8.25 8.25

29

Hydraulic Cylinders and Seals HEAD WEAR RINGS

HEAD WEAR RINGS

ROD DIAMETER (in) (mm)

30

1.50

38.10

1.75 1.87

44.45 47.62

2.00

50.80

2.13

53.98

2.25

57.15

2.37 2.50

60.32 63.50

2.63 2.75

66.68 69.85

3.00

76.20

3.25

82.55

PART NUMBER 8C-9120 4T-6780 8T-5443 8C-3853 4T-6907 8T-6441 8T-6442 4T-6779 8T-8205 4T-5613 8T-7030 8T-6682 8T-6681 4T-6128 8T-4958 8T-8204 8J-1585 9X-7260 8T-0785 8T-5668 8T-8394 8T-8365 8T-7372 8C-9200 8C-9114 4T-7283 6C-2385 8T-7849 8T-7020 8T-6743 8C-9161 8C-9153 9T-0094 8T-1714 8T-7584 8C-9101 8T-4813 8T-0777 8T-6745

A GROOVE WIDTH (± .003 in) (in) (mm)

B GROOVE DIA. (± .001 in) (in) (mm)

0.83 0.98 1.25 1.62 0.98 0.26 0.73 0.98 0.79 0.98 1.25 0.37 0.73 0.98 0.98 1.18 1.43 1.26 0.98 1.25 1.69 2.28 0.98 1.00 1.00 1.25 1.26 1.57 1.81 1.97 0.98 1.18 1.26 1.57 1.65 1.12 1.61 1.73 1.97

1.62 1.62 1.62 2.09 1.87 2.00 2.00 2.00 2.12 2.12 2.12 2.25 2.25 2.25 2.37 2.37 3.35 2.50 2.62 2.62 2.62 2.62 2.75 2.87 2.87 3.01 2.87 2.87 2.87 2.95 3.12 3.20 3.12 3.12 3.12 3.37 3.45 3.37 3.45

21.00 25.00 31.75 41.18 25.00 6.50 18.50 25.00 20.00 25.00 31.75 9.50 18.50 25.00 25.00 30.00 36.31 32.00 25.00 31.75 43.00 58.00 25.00 25.50 25.50 31.75 32.00 40.00 46.00 50.00 25.00 30.00 32.00 40.00 42.00 28.50 41.00 44.00 50.00

41.18 41.18 41.18 53.00 47.53 50.70 50.70 50.70 53.88 53.88 53.88 57.06 57.06 57.06 60.23 60.23 85.09 63.45 66.58 66.58 66.58 66.58 69.76 72.93 72.93 76.33 72.93 72.93 72.93 74.93 79.28 81.28 79.28 79.28 79.28 85.63 87.63 85.63 87.63

Hydraulic Cylinders and Seals HEAD WEAR RINGS

HEAD WEAR RINGS

ROD DIAMETER (in) (mm) 3.25 3.50

82.55 88.90

3.75

95.25

4.00

101.60

4.25 4.50

107.95 114.30

4.75 5.00

120.65 127.00

5.25 5.50

133.35 139.70

5.51 5.75

140.00 146.05

5.91 6.00

150.00 152.40

6.13 6.50

155.58 165.10

6.75 7.00

171.45 177.80

7.25

184.15

7.50 8.00

190.45 203.20

PART NUMBER 8T-6744 119-4761 8C-5245 8T-3329 6J-3075 8T-6746 8T-7848 8T-3330 119-4760 8T-7538 4T-4753 7J-3300 8T-6747 8T-6748 9X-3579 9J-9792 4T-6929 8T-7850 8T-3331 9J-3054 4T-5718 8J-9917 9X-7420 9X-3571 8T-7851 8T-3332 6E-0499 9X-3613 4T-9319 7J-3299 8C-9102 8C-3848 4T-6931 8T-6749 8T-7693 6E-0173 4T-4811 108-0130 6E-0245

A GROOVE WIDTH (± .003 in) (in) (mm)

B GROOVE DIA. (± .001 in) (in) (mm)

2.76 0.98 1.06 1.89 2.00 2.36 1.57 2.44 1.00 1.57 1.89 2.50 2.56 2.36 1.97 3.50 3.50 1.97 2.52 3.62 2.50 2.37 2.37 1.97 1.97 3.62 2.36 1.97 2.76 2.50 2.27 2.60 3.50 3.15 7.14 2.36 2.95 3.15 2.95

3.45 3.76 3.62 3.62 3.76 3.70 3.87 3.95 4.26 4.20 4.26 4.26 4.20 4.45 4.70 4.75 4.75 4.95 5.20 5.25 5.45 5.75 5.76 5.71 5.95 5.95 6.10 6.20 6.26 6.38 6.70 6.70 7.01 7.20 7.26 7.45 7.50 7.70 8.20

70.00 25.00 27.00 48.00 50.70 60.00 40.00 62.00 25.40 40.00 48.00 63.50 65.00 60.00 50.00 88.90 88.90 50.00 64.00 92.07 63.50 60.30 60.32 50.00 50.00 92.00 60.00 50.00 70.00 63.50 57.75 66.00 88.90 80.00 181.36 60.00 75.00 80.00 75.00

87.63 95.42 91.98 91.98 95.40 93.98 98.33 100.33 108.12 106.68 108.08 108.15 106.68 113.03 119.38 120.74 120.74 125.73 132.08 133.45 138.43 146.09 146.30 145.08 151.13 151.13 155.06 157.48 158.88 162.13 170.18 170.18 177.96 182.88 184.28 189.24 190.60 195.58 208.28

31

Hydraulic Cylinders and Seals HEAD WEAR RINGS

HEAD WEAR RINGS

ROD DIAMETER (in) (mm)

32

8.34 8.75

211.93 222.25

9.00 11.00 13.13 13.50

228.52 279.32 333.38 342.90

15.75

400.05

PART NUMBER 4I-6443 108-6216 6E-0248 8C-3846 8C-9156 8C-9155 9X-7439 9X-3563 149-0812 149-0813

A GROOVE WIDTH (± .003 in) (in) (mm) 0.35 2.95 2.95 8.98 5.04 5.03 2.37 10.02 2.37 10.02

8.90 75.00 75.00 228.00 127.97 127.71 60.25 254.41 60.25 254.41

B GROOVE DIA. (± .001 in) (in) (mm) 8.65 8.95 9.01 9.38 11.18 12.93 13.88 13.88 16.13 16.13

219.83 227.33 228.80 238.25 284.09 328.52 352.61 352.61 409.76 409.76

Hydraulic Cylinders and Seals METAL BEARINGS FOR 300 HEX

METAL BEARINGS FOR 300 HEX

Rod Diameter (in) (mm) 1.77 2.17 2.36

45.00 55.00 60.00

2.56

65.00

2.76

70.00

2.95

75.00

3.15

80.00

3.35

85.00

3.54

90.00

3.74

95.00

3.94

100.00

4.13

105.00

4.33

110.00

4.53 4.92 5.00 5.12 5.51 5.71 5.75 5.91

115.00 125.00 127.00 130.00 140.00 145.00 146.00 150.00

Bearing Sleeve Part Number

A Groove Width (in)

(mm)

B Groove Outside Dia. (in) (mm)

198-0664 114-0752 114-0752 114-0753 114-0751 194-8330 114-0754 114-0755 114-0753 114-0750 114-8806 150-5839 114-0755 96-4402 114-0756 114-0760 114-0762 105-2575 96-4402 114-0758 121-1574 96-4430 128-9260 6C-6093 96-5625 114-0757 99-5572 114-0758 114-0760 114-0762 114-0761 191-5644 155-9190 121-1599 114-0763 128-9261 155-9100 121-1607 128-9262

0.79 1.18 1.18 1.59 1.59 1.38 1.59 1.59 1.59 1.59 1.98 1.18 1.59 1.18 1.59 1.98 1.98 1.18 1.18 1.59 1.98 1.18 1.59 1.98 1.38 1.59 1.38 1.59 1.98 1.98 2.37 2.37 2.37 2.37 2.37 2.18 2.37 1.98 2.37

20.00 30.03 30.03 40.30 40.30 35.00 40.30 40.30 40.30 40.30 50.30 30.00 40.30 30.00 40.30 50.30 50.30 30.00 30.00 40.30 50.30 30.00 40.30 50.30 35.00 40.30 35.00 40.30 50.30 50.30 60.30 60.30 60.30 60.30 60.30 55.30 60.30 50.30 60.30

2.17 2.36 2.36 2.95 2.56 2.68 2.76 3.35 2.95 3.15 3.23 3.35 3.35 3.54 3.54 4.33 4.53 3.74 3.54 3.74 3.74 3.94 3.94 3.94 4.15 4.13 4.33 3.74 4.33 4.53 4.53 4.72 5.00 5.20 5.31 5.71 5.79 5.95 6.10

55.00 60.00 60.00 75.00 65.00 68.00 70.00 85.00 75.00 80.00 82.00 85.00 85.00 90.00 90.00 110.00 115.00 95.00 90.00 95.00 95.00 100.00 100.00 100.00 105.50 105.00 110.00 95.00 110.00 115.00 115.00 120.00 127.00 132.02 135.00 145.00 147.00 151.07 155.00

Ring Retaining Part Number NA 99-7001 99-7001 99-5400 99-6975 NA 99-0700 96-8139 99-5400 99-0661 099-0661 99-3205 96-8139 94-0747 7Y-5119 7Y-4672 7Y-4944 93-1571 94-0747 93-1571 93-1571 7Y-4631 7Y-4631 NA 94-1931 93-1572 99-5573 93-1571 7Y-4672 7Y-4944 7Y-4944 7Y-4944 155-9189 121-1598 87-5393 102-0786 155-9099 121-1606 103-8364

33

Hydraulic Cylinders and Seals METAL BEARINGS FOR 300 HEX

METAL BEARINGS FOR 300 HEX

34

Rod Diameter (in) (mm)

Bearing Sleeve Part Number

(in)

(mm)

9.00 10.55

8C-3849 8C-3850

5.04 5.03

127.97 127.71

228.55 268.00

A Groove Width

B Groove Outside Dia. (in) (mm) 9.19 10.75

233.32 273.05

Ring Retaining Part Number NA NA

Hydraulic Cylinders and Seals HEAD SEALS

HEAD SEALS

BORE DIAMETER (in) (mm)

2.50 2.75 3.00 3.15 3.25

63.50 69.85 76.20 80.00 82.55

3.50 3.54

88.90 90.00

3.75 3.94

95.25 100.00

4.00 4.13 4.25 4.33

101.60 104.78 107.95 110.00

4.50 4.72

114.30 120.00

PART NUMBER 149-2695 6F-6673 5F-3999 4J-5477 4J-0522 8H-7521 3K-0360 3D-2824 2S-4078 2M-0338 7F-2122 6V-7658 6V-5057 8F-6711 1H-5728 5H-8848 095-1710 1H-7339 5P-6302 2H-3931 095-1711 095-1671 2H-4145 095-1625 095-1713 095-1626 095-1673 1H-8128 9X-4611 1H-6227 095-1627 112-6920 095-1716 095-1674 095-1675 1J-2859 2H-3928 123-7724 095-1717

DASH SIZE

-228 -230 -232 -234 -240 -236

-238

-240 -241 -242

-244

A GROOVE WIDTH (± .004 in) (in) (mm)

0.22 0.22 0.22 0.25 0.22 0.22 0.22 0.16 0.20 0.22 0.35 0.25 0.36 0.20 0.22 0.22 0.22 0.43 0.26 0.23 0.20 0.20 0.32 0.22 0.32 0.23

5.61 5.61 5.61 6.43 5.61 5.61 5.61 4.00 5.00 5.61 8.93 6.43 9.13 5.00 5.61 5.61 5.61 10.93 6.70 5.73 5.00 5.00 8.22 5.61 8.20 5.73

B GROOVE DIA. (± .005 in) (in) (mm)

CROSS SECTION (in) (mm)

2.28 2.54 2.79 3.15 3.04 3.95 3.29 3.46 3.78 3.54 3.54 3.74 3.74 4.17 3.79 3.91 4.04 3.94 4.08 4.33 4.37 4.56 4.18 4.29 4.41 4.53

0.28 0.14 0.14 0.07 0.14 0.14 0.09 0.12 0.12 0.28 0.21 0.12 0.21 0.14 0.14 0.14 0.12 0.14 0.14 0.14 0.12 0.12 0.14 0.22 0.12 0.22 0.12 0.14 0.14 0.14 0.22 0.16 0.12 0.12 0.12 0.21 0.14 0.20 0.12

57.80 64.45 70.80 79.95 77.15 100.21 83.50 88.00 95.95 89.85 89.95 94.95 94.95 105.95 96.20 99.38 102.55 99.95 103.60 109.95 110.95 115.95 106.06 108.90 112.00 114.95

6.99 3.53 3.53 1.78 3.53 3.53 2.21 2.95 3.00 6.99 5.33 3.10 5.33 3.53 3.53 3.53 3.10 3.53 3.53 3.53 3.10 3.10 3.53 5.70 3.10 5.70 3.10 3.53 3.53 3.53 5.70 4.00 3.10 3.10 3.10 5.33 3.53 5.00 3.10

BACK-UP RING

3C-3239 4J-9225 6J-5731 099-7000 8J-2574 2K-6830 4J-9224

1S-0669 099-0699 099-5399 105-7393 2K-6830 1K-7098 5J-7865 099-0660 105-7360

8J-3752 1K-7095 123-8614 087-5510

35

Hydraulic Cylinders and Seals HEAD SEALS

HEAD SEALS

BORE DIAMETER (in) (mm) 4.72

120.00

4.75

120.65

5.00

36

127.00

5.12

130.00

5.25 5.50

133.35 139.70

5.51

140.00

5.91 6.00

150.00 152.40

6.25 6.30 6.50

158.75 160.00 165.10

6.69 7.00

170.00 177.80

7.09

180.00

7.25

184.10

7.50 7.75

190.50 196.85

7.99 8.25

203.00 209.55

8.50

215.90

PART NUMBER 095-1718 095-1676 133-0128 1S-7408 5H-6734 5P-4326 5F-3144 131-3716 095-1631 095-1719 5F-3106 8F-4469 8J-1688 2H-9247 095-1632 095-1721 095-1633 6D-9157 5H-3252 6J-5541 8F-8733 095-1635 7J-8956 2K-4472 095-1726 8J-1665 9F-1399 095-1728 095-1731 4T-4803 5P-7593 2K-2939 4H-6520 5K-1787 3J-0634 1H-8278 8J-4386 1J-2176 9M-5024

DASH SIZE

-246 -248

-250 -429 -354 -252

-358 -256 -256 -258 -361 -259 -363 -261

-364 -262 -263 -366 -264 -265 -266 -267

A GROOVE WIDTH (± .004 in) (in) (mm) 0.23 0.20 0.13 0.32 0.22 0.32 0.22 0.09 0.36 0.23 0.22 0.48 0.32 0.22 0.36 0.23 0.36 0.32 0.22 0.22 0.22 0.36 0.32 0.22 0.36 0.32 0.22 0.36 0.36 0.19 0.32 0.22 0.22 0.32 0.22 0.22 0.32 0.22 0.22

5.73 5.00 3.23 8.22 5.61 8.22 5.61 2.16 9.13 5.73 5.61 12.13 8.22 5.61 9.13 5.73 9.13 8.22 5.61 5.61 5.61 9.13 8.22 5.61 9.13 8.22 5.61 9.13 9.13 4.72 8.22 5.61 5.61 8.22 5.61 5.61 8.22 5.61 5.61

B GROOVE DIA. (± .005 in) (in) (mm) 4.72 4.76 5.35 4.43 4.54 4.68 4.79 5.43 4.72 4.92 5.04 5.05 5.18 5.29 5.12 5.31 5.51 5.68 5.79 5.79 6.04 5.90 6.18 6.29 6.30 6.68 6.79 6.69 7.48 8.00 6.93 7.04 7.29 7.43 7.54 7.79 7.93 8.04 8.29

119.95 120.95 136.00 112.41 115.25 118.76 121.60 137.92 119.95 125.00 127.95 128.25 131.46 134.30 129.95 135.00 139.95 144.16 147.00 147.00 153.35 149.95 156.86 159.70 159.95 169.56 172.40 169.95 189.95 203.14 175.91 178.75 185.10 188.61 191.45 197.80 201.31 204.15 210.50

CROSS SECTION (in) (mm)

BACK-UP RING

0.12 0.12 0.10 0.21 0.14 0.21 0.14 0.07 0.22 0.12 0.14 0.27 0.21 0.14 0.22 0.12 0.22 0.21 0.14 0.14 0.14 0.22 0.21 0.14 0.22 0.21 0.14 0.22 0.22

3.10 3.10 2.62 5.33 3.53 5.33 3.53 1.78 5.70 3.10 3.53 6.98 5.33 3.53 5.70 3.10 5.70 5.33 3.53 3.53 3.53 5.70 5.33 3.53 5.70 5.33 3.53 5.70 5.70

105-7375

0.21 0.14 0.14 0.21 0.14 0.14 0.21 0.14 0.14

5.33 3.53 3.53 5.33 3.53 3.53 5.33 3.53 3.53

1U-1738 2K-2940 4T-3107 8J-0548 3J-9742 5J-6444 3G-3747 2J-0744 4J-6557

9X-7278 2J-3961 9X-7279 2K-4096 7Y-4633 095-1719 2J-7767 6U-3042 8J-1689 2K-2961 087-5436 4I-3627 7Y-4673 8J-1717 2K-3258 7X-4807 4J-9223 087-5550 7J-8955 2K-4473 7Y-4945 9X-7273 4J-9218 087-5391 4I-6330

Hydraulic Cylinders and Seals HEAD SEALS

HEAD SEALS

BORE DIAMETER (in) (mm) 8.66 9.25

220.00 234.95

9.50 10.00 10.25 10.50 10.75 11.50 12.50 13.13 13.50 13.75 14.25 15.13

241.30 254.00 260.35 266.70 273.05 292.10 317.50 333.38 342.90 349.25 361.95 384.18

PART NUMBER 095-1733 1U-3174 8F-6230 1T-0132 5P-2235 5H-4909 8L-9241 8J-8879 5P-2236 6V-3263 4M-0737 4D-4508 7S-8554 2M-3818 4J-1253

DASH SIZE

-429 -271 -375 -274 -377 -275 -379 -381 -454 -382 -457

A GROOVE WIDTH (± .004 in) (in) (mm) 0.36 0.32 0.22 0.22 0.32 0.22 0.32 0.22 0.32 0.32 0.43 0.43 0.32 0.32 0.43

9.13 8.22 5.61 5.61 8.22 5.61 8.22 5.61 8.22 8.22 10.93 10.93 8.22 8.22 10.93

B GROOVE DIA. (± .005 in) (in) (mm)

CROSS SECTION (in) (mm)

8.27 8.93 9.04 9.29 9.68 10.04 10.18 10.54 11.18 12.18 12.70 13.02 13.43 13.93 14.70

0.22 0.21 0.14 0.14 0.21 0.14 0.14 0.14 0.21 0.21 0.28 0.27 0.21 0.21 0.28

209.95 226.71 229.55 235.90 245.76 254.95 258.46 267.65 283.86 309.26 322.62 330.80 341.01 353.71 373.43

5.70 5.33 3.53 3.53 5.33 3.53 3.53 3.53 5.33 5.33 6.99 6.98 5.33 5.33 6.99

BACK-UP RING 4I-6442 1U-3173 3J-8466 3J-2688 1U-3307 4J-1151 1U-1770 8J-8880 1U-1626 1U-3383 6V-3580 122-0440 9X-4595 4T-4127 4T-5929

37

Hydraulic Cylinders and Seals PISTON SEALS

PISTON SEALS

BORE DIAMETER (in) (mm)

38

0.50 0.63 0.75 1.00

12.70 15.88 19.05 25.40

1.13 1.25

28.58 31.75

1.50

38.10

1.63 1.75

41.28 44.45

1.77 1.97

45.00 50.00

2.00

50.80

2.01 2.17 2.25

50.96 55.00 57.15

2.36

60.00

2.48

63.00

2.50

63.50

2.75

69.85

PART NUMBER

SEAL TYPE

OVERSIZE DIM

3E-4241 3E-4242 3E-4243 3E-4244 3E-4277 3E-4245 3E-4246 3E-4278 4W-2186 3E-4247 5J-9822 3E-4248 3E-4249 3E-4279 8Q-5993 8Q-6121 8Q-6123 3E-4250 5J-7004 1K-5354 144-9483 3E-4251 8C-4908 8C-4905 1U-3998 8J-1587 118-3129 144-9485 125-0776 125-5707 3E-4252 8C-4914 8C-4911 8C-9167 8J-6213 9X-7451 3E-4253 8C-4917 5J-7010

2 2 2 2 1 2 2 1 6 2 1 2 2 1

STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD .060 .030 STD STD STD STD STD STD STD .060 .030 STD STD STD STD .030 STD

2 1 7 2 3 3 1 6

2 3 3 3 1 2 3 1

A GROOVE WIDTH (± .002 in) (in) (mm) 0.08 0.08 0.08 0.08 0.13 0.08 0.08 0.13 0.16 0.08 0.12 0.12 0.12 0.13 0.08 0.08 1.18 0.13 0.19 0.18 0.25 0.13 0.19 0.19 0.19 0.53 0.06 0.25 0.10 2.72 0.13 0.19 0.19 0.19 0.19 0.60 0.13 0.19 0.19

2.11 2.11 2.11 2.11 3.28 2.11 2.11 3.28 3.96 2.11 3.00 3.10 3.10 3.28 2.00 2.00 30.00 3.30 4.88 4.68 6.40 3.30 4.88 4.88 4.88 13.49 1.40 6.40 2.65 69.00 3.30 4.88 4.88 4.88 4.88 15.18 3.30 4.88 4.88

B GROOVE DIA. (± .003 in) (in) (mm) 0.24 0.36 0.49 0.74 0.69 0.86 0.99 0.94 0.99 1.24 1.11 1.24 1.36 1.44 2.17 2.56 2.20 1.61 1.63 2.37 1.55 1.86 1.88 1.88 1.88 3.00 2.56 1.75 3.27 1.18 2.11 2.13 2.13 2.13 2.13 3.14 2.36 2.38 2.38

6.10 9.27 12.45 18.80 17.55 21.97 25.15 23.90 25.02 31.50 28.09 31.40 34.54 36.60 55.00 65.00 56.00 40.79 41.28 60.25 39.46 47.14 47.63 47.63 47.63 76.20 65.00 44.46 83.00 30.00 53.49 53.98 53.98 53.98 53.98 79.78 59.84 60.33 60.33

Hydraulic Cylinders and Seals PISTON SEALS

PISTON SEALS

BORE DIAMETER (in) (mm) 2.75

69.85

2.76

70.00

2.95

75.00

3.00

76.20

3.07 3.15

78.00 80.00

3.25

82.55

3.35 3.50

85.00 88.90

3.54

90.00

3.73 3.74

94.80 95.00

3.75

95.25

PART NUMBER

SEAL TYPE

OVERSIZE DIM

8C-4920 4U-8768 118-2727 8Q-5885 161-7145 8Q-5888 8Q-6032 8Q-6010 8Q-6012 161-7146 3E-4254 6J-1972 8T-8212 8T-8209 9X-7445 9X-7337 2U-8421 099-6998 6U-0849 3E-4255 6J-0793 8C-4926 8C-4923 9J-1797 7Y-5116 3E-4256 8T-8218 8T-8215 4T-8054 096-1588 8Q-5984 144-5287 099-6973 093-1488 8Q-5976 118-3123 8Q-5887 118-3126 3E-4257

3

.060 STD STD STD STD STD STD STD STD STD STD STD .060 .030 STD STD STD STD STD STD STD .060 .030 STD STD STD .060 .030 STD STD STD STD STD STD STD STD STD STD STD

7

7 2 1 3 3 4 3 4 1 1 3 3

2 3 3 3

7 4 5

2

A GROOVE WIDTH (± .002 in) (in) (mm) 0.19 0.24 0.06 0.12 0.25 2.99 0.04 3.19 3.54 0.25 0.13 0.19 0.19 0.19 0.19 0.19 0.18 0.44 0.71 0.13 0.19 0.19 0.19 0.41 0.12 0.13 0.19 0.19 0.19 0.12 0.16 0.25 0.44 1.52 1.57 0.07 0.04 0.37 0.13

4.88 6.00 1.40 3.00 6.40 76.00 1.00 81.00 90.00 6.40 3.30 4.88 4.88 4.88 4.88 4.88 4.65 11.10 18.00 3.30 4.88 4.88 4.88 10.49 3.00 3.30 4.88 4.88 4.88 3.00 4.00 6.40 11.10 38.70 40.00 1.70 1.00 9.50 3.30

B GROOVE DIA. (± .003 in) (in) (mm) 2.38 4.33 2.95 3.35 2.14 1.57 3.15 1.18 0.59 2.34 2.61 2.46 2.46 2.46 2.46 2.46 5.67 2.56 5.51 2.86 2.71 2.71 2.71 2.75 3.92 3.11 2.96 2.96 2.96 4.12 4.13 2.93 2.95 2.99 3.78 3.98 3.94 3.94 3.21

60.33 110.00 75.00 85.00 54.46 40.00 80.00 30.00 15.00 59.46 66.19 62.48 62.48 62.48 62.48 62.48 144.00 64.96 140.00 72.54 68.83 68.83 68.83 69.85 99.60 78.89 75.18 75.18 75.18 104.60 105.00 74.45 74.96 75.96 96.00 101.00 100.00 100.00 81.53

39

Hydraulic Cylinders and Seals PISTON SEALS

PISTON SEALS

BORE DIAMETER (in) (mm) 3.75

95.25

3.94

100.00

4.00

4.02 4.13

40

101.50

102.00 104.80

4.25

107.95

4.33

110.00

4.41 4.49

112.00 114.00

4.50

114.30

PART NUMBER

SEAL TYPE

OVERSIZE DIM

8T-8224 8T-8221 5J-8011 9X-7274 8U-2918 133-3094 9X-7298 5I-5928 8Q-6109 8U-6849 5W-2860 3E-4258 5J-5402 8C-9160 9J-9872 8T-8230 8T-8227 165-6880 2U-6397 125-9695 9X-3586 125-9698 3E-4259 8T-8236 8T-8233 5J-7854 8C-9164 8Q-5974 133-3098 9X-7301 099-6922 123-8614 6U-9270 118-2719 3E-4260 8T-8242 8T-8239 5J-4986 9X-7269

3 3 1 3

.060 .030 STD STD STD .030 STD STD STD STD STD STD STD STD STD .060 .030 STD STD STD STD STD STD .060 .030 STD STD STD .030 STD STD STD STD STD STD .060 .030 STD STD

3 3 4

2 1 3 4 3 3 6

3 2 3 3 1 3 3 3 4

2 3 3 1 3

A GROOVE WIDTH (± .002 in) (in) (mm) 0.19 0.19 0.19 0.19 0.28 0.29 0.29 0.50 4.17 4.53 0.10 0.13 0.19 0.19 0.19 0.25 0.25 0.42 0.22 0.07 0.29 0.37 0.13 0.25 0.25 0.25 0.25 0.04 0.29 0.29 0.50 0.08 0.06 0.07 0.13 0.25 0.25 0.25 0.25

4.88 4.88 4.88 4.88 7.00 7.24 7.24 12.60 106.00 115.00 2.50 3.30 4.88 4.88 4.88 6.40 6.40 10.59 5.50 1.70 7.24 9.50 3.30 6.40 6.40 6.40 6.40 1.00 7.24 7.24 12.60 2.00 1.50 1.70 3.30 6.40 6.40 6.40 6.40

B GROOVE DIA. (± .003 in) (in) (mm) 3.21 3.21 3.21 3.21 4.33 3.38 3.38 3.34 1.18 0.51 4.26 3.61 3.21 3.21 3.21 3.34 3.34 3.50 6.50 4.37 3.57 4.33 3.86 3.59 3.59 3.59 3.59 4.53 3.77 3.77 3.74 4.72 5.00 4.76 4.11 3.84 3.84 3.84 3.84

81.53 81.53 81.53 81.53 110.00 85.75 85.75 84.96 30.00 13.00 108.30 91.59 81.53 81.53 81.53 84.71 84.71 88.90 165.00 111.00 90.75 110.00 97.94 91.06 91.06 91.06 91.06 115.00 95.75 95.75 94.96 120.00 127.00 121.00 104.29 97.41 97.41 97.41 97.41

Hydraulic Cylinders and Seals PISTON SEALS

PISTON SEALS

BORE DIAMETER (in) (mm) 4.50

4.53

114.30

115.00

4.72

120.00

4.75

120.65

4.84

123.00

4.92 5.00

125.00 127.00

5.05 5.12

128.27 130.00

5.14 5.25

130.63 133.35

5.28 5.50

134.06 139.70

PART NUMBER 165-6882 4T-5172 9X-4551 8Q-6125 9X-3589 118-2723 8Q-5971 108-2870 9X-3592 137-5042 3E-4261 8T-8248 8T-8245 9X-7542 4T-8588 8C-5215 2U-8920 135-7934 135-7938 121-1595 3E-4262 7J-2032 8T-8254 8T-8251 6J-9354 5J-5020 9X-7264 8T-1787 6U-3042 108-2869 9X-3595 103-5754 3E-4263 8T-8260 8T-0763 8T-8257 5U-4278 140-0233 3E-4264

SEAL TYPE 3 3 3

3 3 2 3 3 4 3 3

2 1 3 3 4 1 3 3 3 3 2 3 3 3

2

OVERSIZE DIM STD STD .030 STD STD STD STD .030 STD STD STD .060 .030 STD STD STD STD STD STD STD STD STD .060 .030 STD STD STD STD STD .030 STD STD STD .060 STD .030 STD STD STD

A GROOVE WIDTH (± .002 in) (in) (mm) 0.42 0.50 0.50 0.04 0.29 0.37 0.98 0.29 0.29 1.97 0.13 0.25 0.25 0.25 0.25 0.63 0.03 0.07 0.59 0.13 0.13 0.25 0.38 0.38 0.38 0.38 0.38 0.63 0.12 0.29 0.29 0.04 0.13 0.38 0.38 0.38 0.75 0.18 0.13

10.62 12.75 12.75 1.00 7.24 9.50 25.00 7.24 7.24 50.00 3.30 6.40 6.40 6.40 6.40 15.98 0.76 1.70 14.90 3.18 3.30 6.35 9.63 9.63 9.63 9.63 9.63 15.98 3.00 7.24 7.24 1.10 3.30 9.63 9.63 9.63 19.05 4.65 3.30

B GROOVE DIA. (± .003 in) (in) (mm) 4.50 3.84 3.84 4.92 3.97 4.72 4.29 4.16 4.16 4.96 4.36 4.09 4.09 4.09 4.09 4.09 5.00 5.16 5.12 5.58 4.61 3.48 4.23 4.23 4.23 4.23 4.23 4.23 5.52 4.56 4.56 5.38 4.86 4.48 4.48 4.48 5.50 5.40 5.11

114.31 97.41 97.41 125.00 100.76 120.00 109.00 105.74 105.74 126.00 110.64 103.76 103.76 103.76 103.76 103.76 127.00 131.00 130.00 141.68 116.99 88.44 107.32 107.32 107.32 107.32 107.32 107.32 140.27 115.74 115.74 136.63 123.34 113.67 113.67 113.76 139.70 137.10 129.69

41

Hydraulic Cylinders and Seals PISTON SEALS

PISTON SEALS

BORE DIAMETER (in) (mm) 5.50

139.70

5.51

140.00

5.75

5.91

42

146.05

150.00

6.00

152.40

6.25

158.75

6.30

160.00

6.38 6.50

161.93 165.10

PART NUMBER

SEAL TYPE

OVERSIZE DIM

8T-8266 8T-8263 6E-0465 5J-4988 4T-5173 9X-4563 8C-9188 123-3135 133-3102 9X-3598 8Q-5982 121-1603 3E-4265 9J-4981 137-5046 8C-9192 108-2871 9X-3601 3E-4266 8T-8272 8T-8269 8C-9173 5J-4989 4T-4144 8C-4932 8C-4929 3E-4267 8T-8275 5J-4990 8T-1788 8C-4938 8C-4935 133-3106 9X-3604 096-5609 3E-4268 8T-8284 8T-8281 5J-4991

3 3 3 1 3 3

.060 .030 STD STD STD .030 STD STD .030 STD STD STD STD STD STD STD .030 STD STD .060 .030 STD STD STD .060 .030 STD .030 STD STD .060 .030 .030 STD STD STD .060 .030 STD

3 3 3

2 1

3 3 2 3 3 3 1 3 3 3 2 3 1 3 3 3 3 3 2 3 3 1

A GROOVE WIDTH (± .002 in) (in) (mm) 0.38 0.38 0.38 0.38 0.63 0.63 0.12 0.32 0.38 0.38 0.98 0.13 0.16 0.38 0.07 0.12 0.38 0.38 0.16 0.38 0.38 0.38 0.38 0.63 0.63 0.63 0.16 0.38 0.38 0.63 0.63 0.63 0.38 0.38 0.35 0.16 0.38 0.38 0.38

9.63 9.63 9.63 9.63 15.98 15.98 3.00 8.20 9.63 9.63 25.00 3.18 4.06 9.63 1.70 3.00 9.63 9.63 4.06 9.63 9.63 9.63 9.63 15.98 15.98 15.98 4.06 9.63 9.63 15.98 15.98 15.98 9.63 9.63 8.90 4.06 9.63 9.63 9.63

B GROOVE DIA. (± .003 in) (in) (mm) 4.73 4.73 4.73 4.73 4.73 4.73 6.09 4.69 4.75 4.75 5.28 6.33 5.23 4.98 6.30 6.56 5.14 5.14 5.48 5.09 5.09 5.09 5.09 5.09 5.09 5.09 5.73 5.34 5.34 5.34 5.34 5.34 5.54 5.54 6.69 5.98 5.59 5.59 5.59

120.02 120.02 120.02 120.02 120.02 120.02 154.60 119.00 120.62 120.62 134.00 160.73 132.89 126.37 160.00 166.60 130.63 130.63 139.24 129.41 129.41 129.41 129.41 129.41 129.41 129.41 145.59 135.76 135.76 135.76 135.76 135.76 140.61 140.61 169.83 151.94 142.11 142.11 142.11

Hydraulic Cylinders and Seals PISTON SEALS

PISTON SEALS

BORE DIAMETER (in) (mm) 6.50

165.10

6.69

170.00

6.75 6.77 7.00

171.45 171.93 177.80

7.09

180.00

7.25

184.15

7.43 7.48 7.50

188.60 190.00 190.50

7.75

196.85

7.87

200.00

PART NUMBER

SEAL TYPE

OVERSIZE DIM

8C-4944 8C-4941 4T-8695 133-3110 9X-3607 3E-4269 096-5167 3E-4270 8T-8290 8T-8287 5J-4997 8T-1789 8C-5103 8C-5100 124-8364 133-3114 9X-3610 3E-4271 8T-8296 8T-8293 5J-4993 8T-1790 8C-5112 8C-5115 158-3029 125-1286 3E-4272 8C-0561 8C-0558 9J-7117 8T-1791 8C-5121 8C-5118 3E-4273 5J-7016 8T-1792 8C-5127 8C-5124 133-3118

3 3 3 3 3 2

.060 .030 STD .030 STD STD STD STD .060 .030 STD STD .060 .030 STD .030 STD STD .060 .030 STD STD .030 .060 STD STD STD .060 .030 STD STD .060 .030 STD STD STD .060 .030 .030

2 3 3 1 3 3 3 6 3 3 2 3 3 1 3 3 3 3 2 3 3 1 3 3 3 2 1 3 3 3 3

A GROOVE WIDTH (± .002 in) (in) (mm) 0.63 0.63 0.63 0.38 0.38 0.16 0.35 0.16 0.38 0.38 0.38 0.63 0.63 0.63 0.79 0.38 0.38 0.16 0.38 0.38 0.38 0.63 0.63 0.63 0.08 0.38 0.16 0.38 0.38 0.38 0.63 0.63 0.63 0.16 0.38 0.63 0.63 0.63 0.38

15.98 15.98 15.98 9.63 9.63 4.06 8.90 4.06 9.63 9.63 9.63 15.98 15.98 15.98 20.00 9.63 9.63 4.06 9.63 9.63 9.63 15.98 15.98 15.98 2.00 9.63 4.06 9.63 9.63 9.63 15.98 15.98 15.98 4.06 9.63 15.98 15.98 15.98 9.63

B GROOVE DIA. (± .003 in) (in) (mm) 5.59 5.59 5.59 5.93 5.93 6.23 7.08 6.48 6.09 6.09 6.09 6.09 6.09 6.09 6.00 6.32 6.32 6.73 6.34 6.34 6.34 6.34 6.34 6.34 7.75 6.72 6.98 6.59 6.59 6.59 6.59 6.59 6.59 7.23 6.84 6.84 6.84 6.84 6.88

142.11 142.11 142.11 150.62 150.62 158.29 179.83 164.64 154.81 154.81 154.81 154.81 154.81 154.81 152.30 160.62 160.62 170.99 161.16 161.16 161.16 161.16 161.16 161.16 196.85 170.62 177.34 167.51 167.51 167.51 167.51 167.51 167.51 183.69 173.86 173.86 173.86 173.86 174.73

43

Hydraulic Cylinders and Seals PISTON SEALS

PISTON SEALS

BORE DIAMETER (in) (mm)

44

7.87 7.93 8.00

200.00 201.30 203.20

8.25

209.55

8.34 8.50

211.93 215.90

8.66 9.00 9.25

220.00 228.60 234.95

9.28 9.50

235.71 241.30

10.00

254.00

10.25

260.35

10.50

266.70

11.00

279.32

PART NUMBER

SEAL TYPE

OVERSIZE DIM

8C-9179 158-3030 3E-4274 3E-4280 3E-4275 8T-8302 8T-8299 5J-5559 8T-1793 8C-5133 8C-5130 4I-6443 3E-4276 6J-9385 8C-5139 8C-5136 9T-0119 8C-9182 3E-4281 8T-8384 4T-4143 108-6198 8T-8305 3E-4282 9X-7321 123-3129 121-4179 8T-1794 8C-5145 8C-5142 8T-1795 8C-5151 8C-5148 5J-6762 8T-1796 8C-5157 8C-5154 8C-9156 6E-0253

3

STD STD STD STD STD .060 .030 STD STD .060 .030 STD STD STD .060 .030 STD STD STD .030 STD STD .030 STD STD STD STD STD .060 .030 STD .060 .030 STD STD .060 .030 STD STD

2 1 2 3 3 1 3 3 3 2 1 3 3 3 3 1 3 3 3 1 3 1 3 3 3 3 3 3 1 3 3 3 1

A GROOVE WIDTH (± .002 in) (in) (mm) 0.38 0.08 0.16 0.38 0.16 0.38 0.38 0.38 0.63 0.63 0.63 0.35 0.16 0.38 0.63 0.63 0.63 0.38 0.38 0.38 0.38 0.47 0.38 0.38 0.38 0.79 0.44 0.69 0.69 0.69 0.69 0.69 0.69 0.44 0.69 0.69 0.69 5.04 0.69

9.63 2.00 4.06 9.60 4.06 9.63 9.63 9.63 15.98 15.98 15.98 8.90 4.06 9.63 15.98 15.98 15.98 9.63 9.60 9.63 9.63 11.99 9.63 9.60 9.63 20.00 11.18 17.53 17.53 17.53 17.53 17.53 17.53 11.18 17.53 17.53 17.53 127.97 17.53

B GROOVE DIA. (± .003 in) (in) (mm) 6.88 8.25 7.48 7.25 7.73 7.26 7.26 7.26 7.26 7.26 7.26 8.50 7.98 7.51 7.51 7.51 7.51 7.67 8.14 8.26 8.26 9.26 8.26 8.64 8.51 8.49 8.88 8.88 8.88 8.88 9.13 9.13 9.13 9.38 9.38 9.38 9.38 11.18 9.88

174.73 209.54 190.04 184.25 196.39 184.28 184.28 184.28 184.28 184.28 184.28 215.88 202.74 190.63 190.63 190.63 190.63 194.74 206.68 209.68 209.68 235.25 209.68 219.38 216.04 215.76 225.55 225.55 225.55 225.55 231.90 231.90 231.90 238.25 238.25 238.25 238.25 284.09 250.95

Hydraulic Cylinders and Seals PISTON SEALS

PISTON SEALS

BORE DIAMETER (in) (mm) 11.00

279.32

11.50

292.10

12.25 12.50

311.15 317.50

13.00

330.20

13.13 13.50

333.38 342.90

PART NUMBER

SEAL TYPE

OVERSIZE DIM

129-3706 108-0125 8T-1797 8C-5163 8C-5160 8T-6923 6E-0307 129-3712 129-3709 108-6211 8C-9155 130-1857 121-4185

3 3 3 3 3 1 3 3 3 3

.030 STD STD .060 .030 STD STD .030 .030 STD STD .030 STD

3 3

A GROOVE WIDTH (± .002 in) (in) (mm) 0.69 0.69 0.69 0.69 0.69 0.44 0.69 0.69 0.69 0.69 5.03 0.69 0.69

17.53 17.53 17.53 17.53 17.53 11.18 17.53 17.53 17.53 17.53 127.71 17.53 17.53

B GROOVE DIA. (± .003 in) (in) (mm) 9.88 9.88 10.38 10.38 10.38 8.38 11.38 11.38 11.88 11.88 12.93 12.40 12.40

250.95 250.95 263.65 263.65 263.65 212.85 289.05 289.05 301.75 301.75 328.52 314.95 314.95

45

Hydraulic Cylinders and Seals PISTON RING SEALS

PISTON RING SEALS

BORE DIAMETER (in) (mm)

46

0.00 1.50 2.00 2.25

0.00 38.10 50.80 57.15

2.50

63.50

2.68 2.75

68.10 69.85

2.76

70.00

3.00

76.20

3.15

80.00

3.25

82.55

3.50

88.90

3.54

90.00

3.75

95.25

3.94 3.98 4.00

100.00 101.10 101.60

PART NUMBER

OVERSIZE DIM

9J-8102 5J-9073 5J-7942 8C-4802 7H-2423 8C-4804 8J-6212 118-2716 8C-4806 8J-0112 118-2727 118-2717 8T-8361 6J-5733 8C-4947 8T-6443 105-7252 099-7002 8J-2577 7U-7647 8C-4808 8J-6371 8T-6683 7J-9885 8T-8317 4J-3236 8T-8331 105-2630 099-6976 8T-8337 8J-6245 8C-0547 5J-8019 093-1628 125-9696 5J-7154 8C-0539 3D-4522 8T-8311

STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD

A GROOVE WIDTH (± .03 in) (in) (mm)

B GROOVE DIA. (± .08 in) (in) (mm)

0.11 0.50 0.50 0.89 0.89 0.75 0.75 0.21 0.94 0.94 0.06 0.58 1.00 1.00 1.00 1.00 0.24 1.19 0.75 0.75 1.13 1.13 1.13 1.12 1.12 1.50 1.50 0.24 1.19 1.00 1.00 1.25 1.25 0.25 0.30 0.62 0.62 0.71 1.00

0.31 1.24 1.74 1.99 1.99 2.24 2.24 3.63 2.49 2.49 2.95 2.95 2.74 2.74 2.80 2.80 2.83 2.91 2.99 3.50 2.99 2.99 3.05 3.24 3.24 3.24 3.24 3.23 3.31 3.49 3.49 3.49 3.49 3.62 4.33 3.74 3.74 3.74 3.74

2.75 12.60 12.60 22.50 22.50 19.05 19.05 5.40 23.82 23.82 1.40 14.80 25.40 25.40 25.40 25.40 6.15 30.10 19.05 19.05 28.70 28.70 28.70 28.57 28.57 38.00 38.00 6.15 30.10 25.40 25.40 31.65 31.65 6.25 7.60 15.75 15.77 18.13 25.30

7.87 31.53 44.22 50.57 50.57 56.92 56.92 92.10 63.27 63.27 75.00 75.00 69.62 69.62 71.06 71.06 71.98 73.98 75.97 88.90 75.97 75.97 77.41 82.32 82.32 82.32 82.32 81.98 83.98 88.67 88.67 88.67 88.67 91.93 110.00 95.02 95.02 94.99 95.02

Hydraulic Cylinders and Seals PISTON RING SEALS

PISTON RING SEALS

BORE DIAMETER (in) (mm) 4.00

101.60

4.13 4.25

105.00 107.95

4.33 4.37 4.50

110.00 111.10 114.30

4.53 4.75

115.00 120.65

4.92 5.00

125.00 127.00

5.12

130.00

5.25

133.35

PART NUMBER

OVERSIZE DIM

6J-2797 1M-1571 8T-8335 125-9699 8C-0541 6J-7264 8T-8325 6J-4003 5J-8157 8T-8329 093-1629 118-2721 4J-4605 4J-3745 8T-8327 4J-2620 8T-8355 8C-4810 6J-4175 4T-8758 118-2724 7J-8879 8T-8390 4J-3342 8T-8345 4T-9248 135-7939 7J-1627 4J-4630 8C-4812 8M-4226 4J-3420 8T-8339 108-2890 7Y-4632 108-2884 2D-0714 4J-3887 9J-7978

STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD

A GROOVE WIDTH (± .03 in) (in) (mm)

B GROOVE DIA. (± .08 in) (in) (mm)

1.00 1.25 1.25 0.58 1.00 1.00 1.25 1.25 1.50 1.50 0.25 0.30 0.93 1.00 1.00 1.50 1.50 1.87 1.87 1.87 0.58 0.39 1.00 1.25 1.25 1.25 0.58 0.86 1.12 1.12 1.25 1.56 1.56 0.32 0.32 1.59 1.03 1.32 1.50

3.74 3.74 3.74 4.33 3.99 3.99 3.99 3.99 3.99 3.99 4.01 4.72 4.24 4.24 4.24 4.24 4.24 4.24 4.24 4.24 4.72 3.99 4.49 4.49 4.49 4.49 5.12 4.74 4.74 4.74 4.74 4.74 4.74 4.80 4.80 4.84 4.99 4.99 4.99

25.30 31.65 31.65 14.80 25.32 25.32 31.75 31.75 38.00 38.00 6.25 7.60 23.72 25.32 25.32 38.00 38.00 47.52 47.52 47.52 14.80 9.97 25.40 31.65 31.75 31.75 14.80 21.80 28.57 28.57 31.65 39.67 39.67 8.25 8.25 40.30 26.08 33.60 38.10

95.02 95.02 95.02 110.00 101.37 101.37 101.37 101.37 101.37 101.37 101.98 120.00 107.72 107.72 107.72 107.72 107.72 107.72 107.72 107.72 120.00 101.24 114.07 114.07 114.07 114.07 130.00 120.42 120.42 120.42 120.42 120.42 120.42 121.93 121.93 122.87 126.77 126.77 126.77

47

Hydraulic Cylinders and Seals PISTON RING SEALS

PISTON RING SEALS

BORE DIAMETER (in) (mm)

48

5.25

133.35

5.50

139.70

5.51

140.00

5.67

144.00

5.75

146.05

5.91 6.00

150.00 152.40

PART NUMBER

OVERSIZE DIM

8T-8359 7J-8878 4J-4606 8T-8315 8C-4816 3J-9026 7J-3303 8C-4818 8C-4814 7J-1731 8C-9112 4J-3518 8C-4820 8C-4822 8J-1690 107-6264 096-1800 107-6263 5U-4278 118-3955 099-0695 099-0674 9J-4164 6J-3074 096-1581 7J-8877 4J-7503 8C-4824 3G-6537 8C-0543 5J-0014 1J-0708 8T-8343 9J-5860 8T-8347 8T-8349 7J-5326 8J-1746 4T-6930

STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD

A GROOVE WIDTH (± .03 in) (in) (mm)

B GROOVE DIA. (± .08 in) (in) (mm)

1.50 3.92 1.25 1.25 1.37 1.37 1.62 1.75 1.75 1.75 2.00 2.00 2.00 2.25 2.25 0.32 0.32 0.38 0.75 1.78 0.15 0.15 1.62 2.00 0.32 0.39 1.00 1.07 1.07 1.25 1.25 1.32 1.32 1.50 1.50 1.75 1.75 2.75 2.75

4.99 4.50 5.24 5.24 5.24 5.24 5.24 5.12 5.24 5.24 5.24 5.24 5.24 5.24 5.24 5.19 5.19 5.31 5.25 5.23 5.97 5.97 5.49 5.49 5.59 5.25 5.62 5.74 5.74 5.74 5.74 5.74 5.74 5.74 5.74 5.74 5.74 5.62 5.62

38.10 99.69 31.65 31.65 34.82 34.82 41.27 44.45 44.45 44.45 50.70 50.70 50.70 57.15 57.15 8.25 8.25 9.70 19.05 45.30 3.76 3.76 41.27 50.70 8.25 9.97 25.30 27.25 27.25 31.65 31.65 33.60 33.60 38.10 38.10 44.45 44.45 69.85 69.85

126.77 114.25 133.12 133.12 133.12 133.12 133.12 129.96 133.12 133.12 133.12 133.12 133.12 133.12 133.12 131.93 131.93 134.87 133.30 132.87 151.52 151.52 139.47 139.47 141.93 133.30 142.66 145.82 145.82 145.82 145.82 145.82 145.82 145.82 145.82 145.82 145.82 142.66 142.67

Hydraulic Cylinders and Seals PISTON RING SEALS

PISTON RING SEALS

BORE DIAMETER (in) (mm) 6.00 6.25

152.40 158.75

6.30 6.50

160.00 165.10

6.68 6.69

169.77 170.00

6.88 7.00

174.63 177.80

PART NUMBER

OVERSIZE DIM

8C-4826 8T-8357 5J-3326 9J-5550 8C-4828 096-3201 7J-8880 4J-7532 8C-0545 5J-0058 3J-9027 8C-4836 9T-0096 3J-9703 8T-8353 9J-9806 8C-4830 8C-9111 8C-4832 7J-1938 9X-7553 9X-7554 9J-3055 7J-9232 8C-4834 7J-8881 9J-0811 5I-8589 096-5609 105-7262 7J-3302 8C-4838 8M-4228 3G-5098 8T-8363 3G-3470 9J-0711 8C-4840 3G-4641

STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD

A GROOVE WIDTH (± .03 in) (in) (mm)

B GROOVE DIA. (± .08 in) (in) (mm)

2.75 1.50 1.50 1.75 1.75 0.36 0.25 1.00 1.25 1.25 1.37 1.37 1.50 1.50 1.50 1.75 1.75 2.00 2.00 2.00 2.74 2.86 2.88 2.88 3.50 3.50 3.50 0.35 0.36 1.98 2.00 1.75 1.75 2.00 2.00 2.37 3.12 3.12 3.50

5.62 5.99 5.99 5.99 5.99 5.98 5.99 6.12 6.24 6.24 6.24 6.24 6.24 6.24 6.24 6.24 6.24 6.24 6.24 6.24 6.24 6.24 6.24 6.50 5.99 5.99 6.24 6.99 6.38 6.37 6.62 6.74 6.74 6.74 6.74 6.74 6.74 6.74 6.74

69.85 38.00 38.00 44.45 44.45 9.25 6.25 25.30 31.65 31.65 34.82 34.82 38.00 38.00 38.00 44.45 44.45 50.80 50.80 50.80 69.70 72.64 73.03 73.03 88.90 88.90 88.90 8.90 9.25 50.30 50.80 44.45 44.45 50.80 50.80 60.30 79.35 79.37 88.90

142.67 152.17 152.17 152.17 152.17 151.93 152.15 155.36 158.52 158.52 158.52 158.52 158.52 158.52 158.52 158.52 158.52 158.52 158.52 158.52 158.50 158.50 158.52 165.10 152.22 152.22 158.52 177.67 161.93 161.87 168.05 171.22 171.22 171.22 171.22 171.22 171.22 171.22 171.22

49

Hydraulic Cylinders and Seals PISTON RING SEALS

PISTON RING SEALS

BORE DIAMETER (in) (mm)

50

7.09

180.00

7.25

184.15

7.50

190.50

7.75

196.85

7.87

200.00

8.00 8.25

203.15 209.55

PART NUMBER

OVERSIZE DIM

096-5167 105-2653 8T-8319 8J-1662 3J-7848 1J-2674 8T-8341 8C-4846 1U-1734 1U-2218 8C-0549 8J-9936 8C-4848 9J-5562 7J-8886 108-2880 9J-5037 8C-4850 9J-3624 8C-4854 7J-9247 3G-4625 4T-6932 8C-4852 085-7248 9X-3570 8T-7695 7J-8887 4J-7376 2J-0745 8T-8333 3J-8683 8T-8323 8C-4864 3G-9882 8C-4856 8J-8375 3J-7632 7J-3301

STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD

A GROOVE WIDTH (± .03 in) (in) (mm)

B GROOVE DIA. (± .08 in) (in) (mm)

0.36 2.18 1.40 1.40 2.00 2.00 2.00 3.07 3.07 1.50 1.50 2.37 2.50 2.50 0.25 1.62 1.62 2.00 2.00 3.50 3.50 4.50 4.50 4.50 0.36 1.77 5.00 0.50 1.50 1.50 1.50 1.75 1.75 2.00 2.00 2.12 2.12 2.25 2.50

6.77 6.77 6.99 6.99 6.99 6.99 6.99 6.87 6.87 7.24 7.24 7.24 7.24 7.24 7.37 7.49 7.49 7.49 7.49 7.49 7.49 7.37 7.37 7.37 7.56 7.61 7.74 7.74 7.99 7.99 7.99 7.99 7.99 7.87 7.87 7.99 7.99 7.99 7.99

9.25 55.30 35.60 35.60 50.70 50.70 50.70 78.00 78.00 38.00 38.00 60.32 63.50 63.50 6.25 41.27 41.27 50.80 50.80 88.90 88.90 114.30 114.30 114.30 9.25 45.00 126.90 12.75 38.00 38.00 38.00 44.35 44.35 50.80 50.80 53.97 53.97 57.05 63.50

171.93 171.86 177.57 177.57 177.57 177.57 177.57 174.41 174.41 183.92 183.92 183.92 183.92 183.92 187.12 190.27 190.27 190.27 190.27 190.27 190.27 187.12 187.17 187.17 191.93 193.37 196.62 196.60 202.97 202.97 202.97 202.97 202.97 199.81 199.81 202.97 202.97 202.97 202.97

Hydraulic Cylinders and Seals PISTON RING SEALS

PISTON RING SEALS

BORE DIAMETER (in) (mm) 8.25

209.55

8.50

215.90

8.66

220.00

9.25

234.95

9.50

241.30

10.00

254.00

10.03 10.25

254.81 260.35

10.50

266.70

10.75 11.00

273.05 279.40

PART NUMBER

OVERSIZE DIM

8J-8826 8C-4866 4T-9320 3G-1315 9J-3056 6J-9365 8C-4868 7J-8064 8T-7694 4I-6443 6E-0496 125-1204 1J-5281 8T-8321 4T-5949 8C-0551 7J-2087 7J-8883 4T-6097 8J-9932 7J-8884 117-8865 8C-3843 8C-4874 9J-3369 129-3701 7J-8890 8C-4876 7J-8891 8C-4878 9J-1159 8J-8900 8C-4880 8J-5980 8T-6637 6E-0249 129-3703 108-0124 129-3702

STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD

A GROOVE WIDTH (± .03 in) (in) (mm) 2.75 3.50 3.50 4.00 4.13 2.00 2.37 2.37 3.01 0.36 1.18 1.50 1.75 1.75 1.97 2.25 2.25 0.50 1.97 3.08 3.50 1.50 2.76 3.25 3.25 1.50 0.25 3.50 3.50 2.75 2.75 3.75 4.00 4.00 6.50 1.93 1.93 3.25 3.25

69.85 88.90 88.90 101.60 104.78 50.70 60.30 60.30 76.45 9.25 30.00 38.00 44.35 44.35 50.00 57.15 57.15 12.78 50.00 78.20 88.90 38.00 70.00 82.55 82.55 38.00 6.25 88.90 88.90 69.85 69.85 95.25 101.60 101.60 165.10 49.00 49.00 82.55 82.55

B GROOVE DIA. (± .08 in) (in) (mm) 7.99 7.74 7.74 7.87 7.99 8.24 8.24 8.24 8.24 8.34 8.40 8.40 8.99 8.99 8.99 8.99 8.99 9.25 9.12 9.24 8.99 9.74 9.74 9.74 9.74 9.74 9.74 9.74 9.74 10.24 10.24 10.24 10.24 10.24 10.37 10.74 10.74 10.74 10.74

202.97 196.57 196.57 199.80 202.97 209.32 209.32 209.32 209.32 211.93 213.37 213.42 228.37 228.37 228.37 228.37 228.37 234.95 231.56 234.72 228.42 247.42 247.42 247.42 247.42 247.42 247.40 247.47 247.47 260.12 260.12 260.12 260.12 260.12 263.31 272.82 272.82 272.82 272.82

51

Hydraulic Cylinders and Seals PISTON RING SEALS

PISTON RING SEALS

BORE DIAMETER (in) (mm)

52

11.50

292.10

12.25 12.50

311.15 317.50

13.00

330.20

13.13

333.38

13.50

342.90

13.75 14.25 15.13 16.13 18.38

349.25 361.95 384.18 409.60 466.78

PART NUMBER

OVERSIZE DIM

4T-4815 8C-4882 9J-2991 4T-6096 6E-0308 129-3705 1U-2694 108-6215 129-3704 8C-9155 1U-4627 121-4188 130-1859 6E-0247 4T-4129 4T-4825 9X-3564 149-0811

STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD STD

A GROOVE WIDTH (± .03 in) (in) (mm) 1.97 3.87 3.87 4.00 1.46 1.46 4.00 1.46 1.46 5.03 7.87 1.46 1.46 4.02 4.00 7.72 7.72 7.72

50.00 98.42 98.42 101.60 37.00 37.00 101.60 37.00 37.00 127.71 200.00 37.00 37.00 102.00 101.60 196.00 196.00 196.00

B GROOVE DIA. (± .08 in) (in) (mm) 8.99 11.24 11.24 11.87 12.24 12.24 12.24 12.74 12.74 12.93 12.74 13.24 13.24 13.49 13.99 14.74 15.71 17.99

228.37 285.52 285.52 301.41 310.92 310.92 310.92 323.62 323.62 328.52 323.64 336.32 336.32 342.67 355.37 374.44 399.00 456.98

Hydraulic Cylinders and Seals U-CUP SEAL ASSEMBLIES

U-CUP SEAL ASSEMBLIES

Note: Caterpillar is replacing Chevron Packing Seals with U-Cup Seals and spacers. Orders will be filled with the Chevron Packing Seals until the seals are completely exhausted from stock. Both Chevron Packing Seals and U-Cup Seals and spacers meet Caterpillar functional sealing requirements.

Rod Diameter (in) (mm) 1.25 1.50

31.75 38.05

1.75 2.00

44.40 50.80

2.25

57.15

2.50

63.50

2.75 3.00 3.25 3.50

69.85 76.20 82.55 88.85

3.53 4.00

89.55 101.55

4.50

114.25

5.00 5.50 6.00

127.08 139.80 152.35

6.25 6.50 6.75 7.00 7.25

158.75 165.05 171.40 177.80 184.10

PART NUMBER 1K-7110 5F-6308 3D-1123 2K-0248 3F-9609 1K-7112 2K-4434 1H-4492 4F-8420 1K-7114 5F-3498 2J-1408 4J-6897 8M-3912 1J-2148 2K-4010 1K-7104 2K-0050 3K-8340 3J-9740 2K-1335 3K-8330 2J-3723 3K-8350 2J-9325 2K-1888 8M-3910 3J-9741 4J-1195 4J-1150 3J-7768

A BORE DEPTH (± .005 in) (in) (mm)

B BORE DIAMETER (± .012 in) (in) (mm)

0.75 0.75 1.06 1.06 0.98 1.06 1.06 1.22 1.00 1.06 0.98 0.98 1.20 0.83 1.19 1.50 1.50 1.50 0.84 0.83 1.50 0.84 1.64 0.83 1.64 1.50 0.83 0.83 1.11 1.11 0.83

1.75 2.13 2.13 2.38 2.75 2.63 2.88 3.00 3.25 3.13 3.50 3.75 4.00 4.00 4.25 4.50 4.52 5.00 4.50 5.00 5.50 5.50 5.99 6.50 6.50 7.25 7.00 7.25 7.75 8.00 7.75

18.95 19.05 26.87 26.87 24.84 26.87 26.87 30.94 25.35 26.87 24.84 24.84 30.53 21.18 30.23 38.00 38.00 38.00 21.34 21.18 38.00 21.34 41.78 21.18 41.78 38.00 21.18 21.18 28.07 28.07 21.18

44.45 53.98 53.98 60.33 69.85 66.68 73.03 76.20 82.55 79.43 88.90 95.25 101.60 101.60 107.95 114.30 114.85 127.00 114.29 127.00 139.70 139.69 152.27 165.10 165.07 184.15 177.80 184.15 196.85 203.20 196.85

53

Hydraulic Cylinders and Seals PIN SEALS

PIN SEALS PIN DIAMETER (in) (mm)

54

1.06 1.50

26.97 38.10

1.75

44.45

1.88 1.96 2.00

47.63 49.85 50.80

2.25

57.15

2.36 2.37 2.50

59.85 60.32 63.50

2.56 2.63

65.00 66.68

2.75

69.85

2.76 3.00

70.18 76.20

3.14 3.25

79.85 82.55

3.38 3.50

85.73 88.90

3.54

89.95

3.63 3.75

92.08 95.25

3.94 4.00

100.00 101.60

4.13 4.25 4.33 4.38

104.78 107.95 110.00 111.13

BORE DIAMETER

PART NUMBER

Gland

(in)

(mm)

7K-0366 7K-9201 9D-6581 7K-9202 5P-8842 3P-1347 227-3857 7K-9203 9D-6583 5P-8843 7K-9204 9D-6584 8T-7535 3P-1461 7K-9205 5P-8845 9D-6585 8T-7536 7K-9207 9D-6586 7K-9208 9D-6588 5P-8847 8T-7537 229-9323 7K-9209 9D-6589 5P-4061 3E-6756 8T-5048 7K-9210 115-8192 3G-5052 7K-9211 9D-6591 7K-9212 7K-9213 3E-6757 7X-4803 118-3675 3G-6487 7K-9214 5P-2671 9X-4597 7K-9216 7K-9217 3E-6758 6V-3261 5P-3193 9X-4598 3G-5053

6.54 6.34 6.34 6.35 6.35 11.18 5.08 6.31 6.34 6.34 6.34 6.35 6.58 6.35 6.34 6.36 6.36 6.75 6.33 6.36 6.34 8.61 6.36 6.79 6.84 6.34 6.36 9.51 9.53 6.83 6.34 7.86 7.97 6.33 6.36 7.90 9.51 12.70 8.03 12.53 12.70 7.93 9.49 8.00 7.87 9.54 12.70 7.96 6.36 10.00 10.20

1.58 2.00 2.00 2.25 2.25 2.38 2.36 2.50 2.50 2.50 2.75 2.75 2.87 2.88 3.00 3.00 3.00 3.09 3.12 3.13 3.25 3.25 3.25 3.29 3.30 3.50 3.50 3.75 3.75 3.68 3.75 3.87 4.00 4.00 4.00 4.12 4.25 4.50 4.17 4.53 4.62 4.37 4.50 4.57 4.62 4.75 5.00 4.75 4.75 5.12 5.00

40.05 50.77 50.78 57.15 57.15 60.33 60.00 63.42 63.47 63.47 69.82 69.84 73.00 73.03 76.17 76.21 76.21 78.50 79.34 79.40 82.52 82.58 82.58 83.50 83.86 88.87 88.91 95.22 95.25 93.50 95.22 98.26 101.67 101.55 101.61 104.70 107.92 114.30 106.00 115.00 117.47 111.10 114.23 116.00 117.33 120.67 127.00 120.70 120.67 130.00 127.00

Hydraulic Cylinders and Seals PIN SEALS

PIN SEALS PIN DIAMETER (in) (mm) 4.50

114.30

4.72 4.75 4.87 5.00

119.85 120.65 123.82 127.00

5.11 5.25 5.51

129.85 133.35 139.85

5.63

142.88

5.90

149.85

6.00

152.40

6.13 6.29

155.58 159.85

6.50 6.69 7.08 7.25 7.87 8.00 8.66 9.00 9.29

165.10 169.85 179.80 184.15 199.85 203.20 219.85 228.60 236.00

BORE DIAMETER

PART NUMBER

Gland

(in)

(mm)

7K-9218 5P-2672 9X-4599 7K-9219 6V-0273 7K-9220 5P-8488 9X-4600 5P-2673 9X-4601 197-3919 168-8508 168-6448 5P-5520 9X-7699 113-5950 5P-8190 5P-4627 9J-5815 9X-7700 187-9753 5P-2322 9X-7701 160-5875 5P-9609 9X-7702 7X-4786 9X-7703 8K-5271 174-0255

9.51 12.66 10.08 7.93 9.46 9.49 12.70 12.08 9.49 12.08 12.65 14.00 9.53 12.65 10.08 9.50 9.52 12.70 11.11 12.11 15.08 9.49 12.08 15.10 9.77 12.08 9.54 10.08 11.11 10.00

5.25 5.50 5.51 5.37 5.62 5.75 6.00 6.06 6.00 6.46 6.50 6.61 6.38 6.62 6.69 7.09 6.75 7.00 7.00 7.25 7.48 7.25 7.64 8.27 8.02 8.82 8.75 9.45 9.87 10.08

133.31 139.62 140.00 136.50 142.73 145.97 152.40 154.00 152.32 164.00 165.15 168.00 161.93 168.18 170.00 180.00 171.45 177.80 177.80 184.07 190.00 184.07 194.00 210.00 203.70 224.00 222.27 240.00 250.82 256.00

55

Hydraulic Cylinders and Seals SNUBBER SEALS

SNUBBER SEALS GROOVE WIDTH PART NUMBER 103-8341 116-3519 155-9187 185-9050 185-9051 191-3128 191-5706 216-3418 242-6833 5I-8516 6I-6784 6I-6785 6I-6786 6I-6787 6I-6790 6I-6921 6I-6922 7I-1352 87-5389 200-3620

56

(in) 0.28 0.43 0.35 0.28 0.28 0.43 0.43 0.43 0.43 0.35 0.35 0.43 0.35 0.35 0.43 0.28 0.28 0.35 0.35 0.43

GROOVE DIA. (mm) 7.00 11.00 9.00 7.00 7.00 11.00 11.00 11.00 11.00 9.00 9.00 11.00 9.00 9.00 11.00 7.00 7.00 9.00 9.00 11.00

(in) 2.44 4.65 3.93 2.52 2.32 3.41 3.61 5.75 3.22 3.34 2.95 3.41 2.56 3.15 4.37 2.52 2.24 2.75 4.10 4.02

(mm) 61.90 118.14 99.90 63.90 58.95 86.67 91.62 145.96 81.85 84.90 74.90 86.67 64.92 79.90 110.90 63.90 56.95 69.90 104.06 102.13

Hydraulic Cylinders and Seals TROUBLESHOOTING

Seal Failures When seal failure occurs, it is important to determine the cause of failure in order to provide maximum replacement seal performance and life. The most common causes of seal failures, other than normal wear, are improper installation, incorrect seal application and seal damage resulting from the condition of the cylinder assembly components. Other contributing factors to seal failure are contamination in the hydraulic system, seal extrusion and excessive heat. As seal failure may occur from more than one factor, it is critical to examine all aspects of the hydraulic system. These steps will assist you in analyzing seal failures. Also provided are questions to ask or clues to look for when performing each step. 1. Investigate the worn seal’s previous performance 2. Visually examine the worn seal for damage 3. Inspect the cylinder assembly component

Step 1: Investigate Previous Performance • •

Find out if there has been a history of failures. Repeated failures may indicate the seal itself is not the problem. Determine when a leak started. Can it be related to a change in maintenance or operating procedures?

Step 2: V isual Examination • •

Look for physical damage such as surface tears, scratches, extruded material, foreign particles, etc. Look for wear patterns on the seal lip(s). -- Normal wear will flatten the sharp edge of the lip at its contact point. -- Excessive lip wear can be caused by too little lubrication. -- Rapid lip wear, often evidenced by the lip being totally blown off, can be caused by too much pressure.

•

-- Cracked and hardened lips can result from excessive heat. Measure the seal’s inside and outside diameters to determine changes in the seal’s dimensions.

•

Look at the markings on the outside diameter of piston seals. -- Marks should be straight and uniform if the seal was properly installed. -- Deep scratches can be caused by a damaged bore. -- Alternating pattern of smooth and marked areas can be a sign of an out-of-round bore.

•

•

Has the seal’s material softened or hardened? -- Check for incompatibility between the seal’s material and the system’s fluid, excessive heat, and/or too little lubrication. Match the seal type and material to the application. -- Refer to the previous section “Seal Applications”.

Step 3: Inspect Cylinder Assembly Components •

Inspect the cylinder bore and rod for damage. Look for: -- burrs, nicks, cuts, scratches or sharp edges -- corrosion -- flaking of rod chrome -- bent rod If the cause of premature seal failure cannot be determined after completing the above three steps, investigate the operating conditions of the entire hydraulic system. Investigate the system’s operating pressure and hydraulic fluid and look for changes in service or operating conditions.

57

Hydraulic Cylinders and Seals INSTALLATION

Seal Installation Improper seal installation is one of the major causes of seal failures. To provide maximum seal performance and life, the use of proper seal installation procedures is critical. When disassembling the cylinder, place the used seals on a clean, flat work surface in the order in which they were removed. Identify the seals, making sure that none of the required seals are missing. Inspect the seals to help you determine the cause of seal failure. Look for signs of normal wear or damage caused by the condition of the cylinder components or problems related to the system’s pressure or fluid (temperature or seal material compatibility). If wear appears to be normal, replace the used seals with new Caterpillar seals of the same type and size. If seal failure appears to be from other than normal wear, determine the corrective action to be taken in terms of: seal replacement, cylinder component repair, or adjustments to the hydraulic system’s fluid or operating pressure.

Installation of Vented Buffer Seal Assembly, U-Cup Seal, and Double Lip W iper Seal for Hydraulic Cylinders Introduction This instruction gives the procedure for installing seals in the head of hydraulic cylinders. There are three seals in this kit. The three seals are one vented buffer seal assembly, one U-Cup seal, and one double lip wiper seal.

1. Install vented buffer seal assembly (1). The seal assembly consists of one seal (1A) and one backup ring (1B) . a. Install vented buffer seal (1A) in the correct groove of cylinder head (4). Seal (1) has a groove for backup ring (1B).The groove must face the rod end of the cylinder. Refer to Illustration 1 for the correct assembly position. b. Install backup ring (1B) in seal (1A). Refer to Illustration 1 for the correct assembly position. 2. Install the U-Cup seal (2) in head (4). Install the seal with the open end of the "U" facing toward the piston end of the cylinder. Refer to Illustration 1 for the correct assembly position. 3. Use sandpaper or emery cloth to scuff the surfaces of the counterbore in the cylinder head and the outside diameter (3A) of the wiper seal's metal shell. 4. Clean the counterbore in the head and the outside diameter (3A) of the wiper seal's metal shell with 8T-9011 Component Cleaner or 6V-1541 Quick Cure Primer . Clean the counterbore and the metal shell until neither of the components discolor a clean white towel. Note: The metal shell of the wiper seal is coated with a corrosion inhibitor. This may prevent proper bonding of the wiper seal to the cylinder head if the inhibitor is not removed. After cleaning, do not touch the counterbore or the metal shell because the oil from your fingers may prevent a good bond. Handle the seal by the lip only.

58

Hydraulic Cylinders and Seals INSTALLATION

5. Apply 6V-1541 Quick Cure Primer on the counterbore and the metal shell. Allow the primer to dry. The primer will dry in approximately 30 seconds. 6. Apply 7M-7456 Bearing Mount Compound evenly but do not apply the compound excessively. Apply the compound to the counterbore and to the metal shell. Do NOT allow the compound to contact the sealing lip. 7. Install double lip wiper seal (3) into the cylinder head. Refer to surface (3B) in order to make sure that the marking "THIS SIDE OUT" on the seal is toward the rod end. Refer to Illustration 1 for the correct assembly position. The seal should be firmly seated against the bottom of the counterbore. Wipe away any excess bearing mount compound. Allow the compound to dry for 15 minutes before assembling the hydraulic cylinder. 8. Lightly lubricate the seals with clean hydraulic fluid before installing the head on the cylinder rod.

General Installation Procedures: Keep seals packaged until needed for assembly. Double-check seal part number for accuracy. Double-check part number dimensions with iron dimensions. Clean and inspect all surfaces before installation. Protect the seal from any sharp edges it may come into contact with during installation. Prelubricate the surfaces the seal will contact during installation (usually with system fluid). Use only clean, recommended installation tools.

Installation Tools: Many of the hydraulic cylinder seals can be pressed or snapped into place by hand. The more flexible seals can be formed by hand into a kidney shape and then “popped” into the groove. Never use steel hammers, chisels, screwdrivers, or any item with a sharp surface which can damage the seal during installation. Caterpillar offers the following tools to aid in hydraulic cylinder seal installation. These tools are also listed in the Tools and Shop Products Guide (NENG2500) Rod Seal Guide

Used for guiding the head (with rod seals already installed) on rods with square shoulders. The rod shoulder can be sharp and cut the seal. This tool will guide the seal over the rod without cutting or damaging the seal.

1P0510 Driver Group

Used for installing press-in wipers flush with a housing or some distance below a housing surface. Contains a set of drive plates from 7/16” (11.1mm) to 3.00” (76.2mm) diameter. Drive plates are in 1/16” (1.59mm) increments.

59

Hydraulic Cylinders and Seals INSTALLATION Buffer Installer 4C4069 1.5" Installer

4C4070 1.75" Installer

Used to install the 8C9122 Step Buffer Seal Assembly in hydraulic cylinders on the 910 and 910E Wheel Loader, 508 Skidders, and the D3B Track-Type Tractor.

Used to install the 8C9123 Step Buffer Seal Assembly in hydraulic cylinders on the 416, 426, 428, 436 and 438 Backhoe Loaders.

5P1720 Seal Pick

Used for removal and installation of all types of oil seals. One end of the pick is pointed for prying out flexible seals. The blunt, hook end is used to align seals for installation and to eliminate the twist that occurs when installing O-ring seals. Both ends of the pick are hardened and provide much greater strength than would normally be expected from a tool of this size.

5P5263 Tool Group

Used to install Teflon piston seals on the pistons of threaded crown hydraulic cylinders with bore sizes ranging from 2.50” (63.50 mm) to 4.00” (101.60 mm). Installation by hand can cause too much distortion, and the seal can be cut when the piston is assembled into its cylinder.

Teflon Seal Tools

The following tools are available to install cylinder pistons and to reassemble the piston into the cylinder boore: Various size compressor assemblies 4S9447, 4S9448, 4S9449, 4S9450, 9S9451, 9S9452, 9S9453, 9S9454 9S9455 and 9S9456; expander assembly 4S9181; and clamp assembly 4S9446 . See the Numerical Parts Record for individual part details.

60

Hydraulic Cylinders and Seals HOW TO USE THIS SECTION The next section of this book contains information on Cat hydraulic cylinders. Sorted by machine model, this information includes cylinder group and cylinder assembly part numbers, engineering change levels, cylinder length and bore diameter, rod length and diameter, and part number for Cat Reman products and seal kits. Following are tips for using this section:

a

b

c

d

e

e

f

f

e

e

f

f

g

g

1.

Determine the hydraulic cylinder group number and change level from the parts book or microfiche or from the tag on the outside of the cylinder.

2.

Refer to the index on page1 to locate the machine family and find the machine model Part Number Index section to determine the proper page number.

3.

Match the

a , or go to the

b Application with the Cylinder Group Number d and the Engineering Change Level column c .

In order to select the correct seal kit, the cylinder group part number and the engineering design change level of the cylinder group to be resealed must be known. Caterpillar makes changes to the consist of the cylinder groups changes, the engineering design change level of the group changes, i.e. 01, 02, 03, 04. Different seal kits are sometimes required to reseal different engineering change levels of the same cylinder group part number. If your cylinder is a bolted-head design, this engineering design change level will be welded onto the cylinder. If your cylinder is a threaded-crown or threaded-gland design, this engineering design change level will be stamped on the outside of the cylinder tube. The engineering design change level is located in column c in the chart. 4.

Select the Remanufactured Rod and Cylinder part number

e .

All Reman options available for Canceled/Replaced assemblies may not be listed in this book. 5.

Refer to the Dimension Columns f for identification purposes only.

Do Not Use These Dimensions As Rebuild Specifications. 6.

Select the Standard or Oversize Seal Kit Part Number

g .

61

55B

55

45B

00 - 01

N/A

Rod length is from rod end to centerline of eye.

02 - up

00 - up

N/A 00 - 01

02 - up

N/A

N/A

00 - 01

N/A

N/A

02 - up

N/A

02 - up

N/A 00 - 01

00 - 01

N/A

N/A

02 - up

N/A

00 - up

N/A 00 - 01

02 - up

N/A

00 - 01

N/A

00 - up

N/A

N/A

02 - up

N/A

02 - up

00 - 01

N/A

N/A

02 - up

N/A

00 - 01

00 - 01

N/A

00 - up

N/A

Eng Chanineering D ge L evel esign

Boom

Application

C

151-8992

151-8881

151-8881

160-0159

151-8992

151-8992

151-8881

151-8881

151-8992

151-8992

151-8881

151-8881

160-0159

151-8992

151-8992

151-8881

151-8881

160-0158

151-8992

151-8992

151-8881

151-8881

Cyli Part nder Ass No. emb ly

112-8948

Rod No. Assemb lyPa rt

(In.) ngth C

ylind er Le

Rem Par an Sta n t d N a o rd C . ylind e

r Cylinder length is from open end to centerline of eye.

164-4674

164-4674

164-4674

164-4674

164-4674

164-4674

164-4674

164-4674

164-4674

Rod L

(In.)

165-7747

165-7746

165-7746

171-1421

165-7747

165-7747

165-7746

165-7746

165-7747

165-7747

165-7746

165-7746

171-1421

165-7747

165-7747

165-7746

165-7746

171-1168

165-7747

165-7747

165-7746

165-7746

171-1421

Cylinder length is from open end to centerline of trunnion.

engt h

p Pa rt No . ylind er G rou

160-0159

dard Stan

. t No t Par Seal Ki

re Stan Diamdard Cy linde . (In. r Bo )

Agricultural Tractors

"O .030

. t No t Par /S Se al Ki

62

45

35

Model

Hydraulic Cylinders and Seals

Sorted by MACHINE MODEL

Ro d D iame ter (I n.

)

an R od P

art N o. Rem

65E

65D

65C

00 01 02 - up

Tensioner

Tensioner

Rod length is from rod end to centerline of eye.

00 - up

00 - up

Tensioner

Lift

04 - up

N/A

Tensioner

00 - 03

00 - up

Tensioner 00 - up

00 - up

N/A

Lift

04 - up

N/A

N/A

00 - 03

N/A

00 - up

N/A 00 - up

00 - up

Lift

Lift

01 - up

Lift

00 - up

N/A 00

00 - up

Lift

Lift

01 - up

Lift

65B

00

Lift

65

02 - up

N/A

Application

Eng Chanineering D ge L evel esign

55B

Model

C

148-3031

148-3031

148-3031

9T-9517

150-4382

108-6296

108-6296

9T-9517

150-4382

9T-7802

108-6296

108-6296

9T-9517

9T-7802

9T-9517

9T-2230

9T-2230

9T-7802

9T-9517

9T-2230

9T-2230

Cyli Part nder Ass No. emb ly

150-4383

150-4383

6E-1421

9T-9773

150-4383

150-4383

6E-1421

9T-9773

150-4383

9T-7803

150-4383

6E-1421

9T-9773

9T-7803

9T-9773

9T-2476

9T-2476

9T-7803

9T-9773

9T-2476

9T-2476

r Rem Par an Sta n t d N a o rd C . ylind e

9.25

9.25

9.25

4.00

9.25

9.25

9.25

4.00

9.25

9.25

9.25

9.25

C

35.80

35.80

35.80

21.42

35.80

35.80

35.80

21.42

35.80

34.89

35.80

35.80

21.42

34.89

21.42

21.64

21.64

34.89

21.42

21.64

21.64

r>Pa rt

151-6273

148-5281

148-5281

9T-9776

101-9742

101-9742

101-9742

9T-9776

101-9742

9T-7811

101-9742

101-9742

9T-9776

9T-7811

9T-9776

9T-2474

9T-2474

9T-7811

9T-9776

9T-2474

9T-2474

No. Part Rem

an R od

(In.) ngth ylind er Le

Cylinder length is from open end to centerline of eye.

0R-7405

0R-7405

0R-7405

0R-7405

0R-7405

0R-7405

4.00

9.25

4.00

4.00

4.00

9.25

4.00

4.00

4.00

Rod No. Assemb lyPa rt

189-5987

189-4906

174-5200

171-2054

174-5200

171-2054

174-5200

171-2054

174-5200

171-2054

151-6273

148-5281

148-5281

151-6273

148-5281

148-5281

101-9742

101-9742

101-9742

101-9742

101-9742

101-9742

9T-9776

No. Part Rem

an R od

(In.) ngth ylind er Le

21.42

Rod No. Assemb lyPa rt

199-7701

Rod No. Assemb lyPa rt

141-6670

191-9435

183-8013

180-4136

141-5844

235-3491

223-1336

207-7467

207-7467

207-7467

207-7467

207-7467

207-7467

193-0676

183-3391

151-7034

146-8932

141-6670

154-6413

154-6413

No. Part Rem

an R od

(In.) ngth ylind er Le

31.32

Rod No. Assemb lyPa rt

137-6179

4U-1676

4U-1676

4U-1676

4U-1676

7U-8516

7U-7091

193-0676

183-3391

151-7034

134-0010

7U-7550

7U-7550

6U-3248

193-0676

183-3391

151-7034

4U-7387

No. Part Rem

0R-7376

0R-7376

0R-7376

0R-7376

10R-0197

10R-0197

0R-7350

0R-7350

an R od

(In.) ngth ylind er Le

Cylinder length is from open end to centerline of eye.

0R-7403

0R-7403

10R-0174

0R-7404

Rod No. Assemb lyPa rt

6U-1041

5U-3576

4U-1676

4U-1676

4U-1676

4U-1676

143-3303

143-3303

6U-1041

7U-7980

6U-1041

2U-9454

7U-7980

137-6179

136-7337

7U-7980

4U-1676

4U-1676

4U-1676

No. Part Rem

0R-7376

0R-7376

0R-7376

0R-7376

10R-0629

0R-7376

0R-7376

0R-7376

0R-7376

an R od

(In.) ngth ylind er Le

Cylinder length is from open end to centerline of eye.

0R-7401

0R-7403

0R-7403

0R-7384

0R-7384

0R-7403

0R-7403

Rod No. Assemb lyPa rt

7U-7550

Rod No. Assemb lyPa rt

4U-7387

4U-7387

4U-7387

6U-1041

193-0676

183-3391

151-7034

4U-7387

4U-7387

4U-7387

4U-7387

146-6653

146-6653

141-5856

146-6653

119-2123

7U-8516

193-0676

183-3391

151-7034

No. Part Rem

0R-7350

0R-7350

0R-7350

0R-7350

0R-7350

0R-7350

0R-7350

an R od

(In.) ngth ylind er Le

23.54

Rod No. Assemb lyPa rt

7U-7085

7U-7085

6U-1041

106-8043

106-8043

106-8043

193-0676

183-3391

151-7034

7U-7980

142-0427

133-1257

7U-7980

4U-7387

4U-7387

141-6670

4U-7387

No. Part Rem

0R-7350

0R-7350

0R-7350

0R-7350

an R od

(In.) ngth ylind er Le

Cylinder length is from open end to centerline of eye.

0R-7370

0R-7370

0R-7370

186-7155

0R-7404

0R-7404

Rod No. Assemb lyPa rt

4U-7387

4U-7387

4U-7387

141-6670

143-3303

143-3303

6U-1041

7U-7980

7U-7085

7U-7085

6U-1041

106-8043

106-8043

106-8043

193-0676

183-3391

151-7034

7U-7980

No. Part Rem

0R-7350

0R-7350

0R-7350

an R od

(In.) ngth ylind er Le

19.48

Rod No. Assemb lyPa rt

9T-5799

9T-4811

9T-4008

4T-7011

4T-7011

4T-7011

9T-5799

9T-6238

9T-5799

9T-4933

4T-5608

9T-6238

9T-5799

9T-4933

4T-5608

3U-3319

143-3303

No. Part Rem

0R-2801

0R-8968

0R-8965

0R-2701

0R-2701

0R-2701

0R-2801

0R-8969

0R-2801

0R-2711

0R-8969

0R-2801

0R-2711

an R od

(In.) ngth ylind er Le

29.25

Rod No. Assemb lyPa rt

134-2659

134-2659

109-7022

109-7022

6E-1511

9T-7071

9T-7071

130-2367

130-2367

105-2340

105-2340

164-7176

9T-3948

9T-0661

9T-4008

6E-1502

6E-1502

9T-3948

9T-3948

9T-0777

105-2977

No. Part Rem

0R-8975

0R-8975

0R-2716

0R-2716

0R-2716

0R-2716

0R-2798

0R-2707

0R-8965

0R-8982

0R-8982

0R-2798

0R-2798

0R-2708

an R od

(In.) ngth ylind er Le

9.17

Rod No. Assemb lyPa rt

6E-1522

164-7176

134-2659

164-7176

9T-0661

9T-4008

178-4639

178-4639

6E-1522

114-2229

125-7894

6E-0289

6E-1757

134-2659

109-7022

109-7022

116-0732

116-0732

172-2354

172-2354

No. Part Rem

0R-8985

0R-8975

0R-2707

0R-8965

0R-8985

0R-8979

0R-8987

0R-8975

10R-0194

an R od

(In.) ngth ylind er Le

Cylinder length is from open end to centerline of eye.

0R-2445

0R-8966

0R-8966

0R-8978

0R-8977

0R-8977

0R-8986

0R-8974

0R-8974

0R-7368

0R-7369

Rod No. Assemb lyPa rt

134-2659

201-4902

159-5848

166-8131

166-8132

134-2659

164-7176

110-8691

119-2110

110-8691

119-2110

9T-4008

9T-4008

9T-4008

166-8132

159-5848

9T-3948

9T-3948

125-7894

125-7894

No. Part Rem

0R-8975

10R-0635

10R-0640

0R-8975

0R-8965

0R-8965

0R-8965

10R-0635

0R-2798

0R-2798

0R-8979

0R-8979

an R od

(In.) ngth ylind er Le

2.40

Rod No. Assemb lyPa rt

134-2659

116-0732

116-0732

126-6953

235-9835

235-9835

209-9241

178-4639

134-2659

9T-0661

6E-1522

125-7894

164-7176

9T-0661

9T-4008

9T-4008

9T-4008

178-4639

178-4639

235-9835

No. Part Rem

0R-8975

0R-8975

0R-2707

0R-8985

0R-8979

0R-2707

0R-8965

0R-8965

0R-8965

an R od

(In.) ngth ylind er Le

Cylinder length is from open end to centerline of eye.

0R-2445

0R-8966

0R-8966

0R-8966

3.50

3.50

Rod No. Assemb lyPa rt

9T-4008

Rod No. Assemb lyPa rt

155-6520

9T-4008

106-8714

6E-3709

166-8134

175-7806

166-8134

6E-5571

6E-5571

6E-5571

159-6111

9T-0752

9T-0752

6E-0289

6E-0289

6E-0289

6E-1939

No. Part Rem

0R-8965

0R-7351

0R-2709

0R-2709

0R-7348

an R od

(In.) ngth ylind er Le

39.20

Rod No. Assemb lyPa rt

4T-6888

9T-9750

9T-1732

9T-0803

9T-0803

9T-0803

9T-0803

9T-0661

105-2892

9T-5799

9T-4811

9T-4008

4T-7011

4T-7011

4T-7011

9T-5799

9T-6238

9T-5799

9T-4933

No. Part Rem

0R-8971

10R-0196

10R-0196

10R-0196

10R-0196

0R-2707

0R-2801

0R-8968

0R-8965

0R-2701

0R-2701

0R-2701

0R-2801

0R-8969

0R-2801

0R-2711

an R od

(In.) ngth ylind er Le

42.73

Rod No. Assemb lyPa rt

116-0732

126-6953

126-6953

126-6953

125-7894

6E-0289

164-7176

9T-4008

6E-1502

6E-3704

6E-1502

9T-0752

9T-0752

6E-0289

6E-1511

134-2659

134-2659

109-7022

109-7022

9T-0803

9T-0803

No. Part Rem

0R-8979

0R-8965

0R-8982

0R-8982

0R-2709

0R-2709

0R-8975

0R-8975

10R-0196

10R-0196

an R od

(In.) ngth ylind er Le

39.67

Rod No. Assemb lyPa rt

155-6520

119-2110

110-8691

119-2110

155-6520

9T-4008

184-4752

184-2365

184-2365

183-9238

125-7894

125-7894

125-7894

125-7894

6E-1757

180-6111

134-2659

134-2659

126-6953

235-9835

No. Part Rem

0R-8965

0R-8979

0R-8979

0R-8979

0R-8979

0R-8987

0R-8975

0R-8975

an R od

(In.) ngth ylind er Le

Cylinder length is from open end to centerline of eye.

0R-8966

0R-8966

0R-8988

0R-8977

0R-8986

3.50

4.50

4.50

2.75

Rod No. Assemb lyPa rt

9T-4008

Rod No. Assemb lyPa rt

9T-0752

6E-0289

6E-0289

6E-0289

6E-1939

6E-5191

9T-7071

9T-7071

130-2367

130-2367

105-2340

105-2340

9T-0661

9T-4008

6E-1817

6E-1817

6E-1817

6E-5571

6E-5571

6E-5571

No. Part Rem

0R-2709

0R-7348

0R-8963

0R-2716

0R-2716

0R-2716

0R-2716

0R-2707

0R-8965

10R-0130

10R-0130

10R-0130

an R od

(In.) ngth ylind er Le

52.57

Rod No. Assemb lyPa rt

131-1856

6Q-2199

197-8080

197-8080

155-6520

165-5180

114-2229

119-2110

9T-0752

9T-2821

9T-2821

126-0240

110-8691

112-5734

110-8691

155-6520

9T-4787

162-8059

9T-6332

No. Part Rem

10R-0194

0R-2709

10R-0126

an R od

(In.) ngth ylind er Le

48.02

Rod No. Assemb lyPa rt

9T-7337

9T-5799

9T-4933

4T-5608

9T-3169

9T-0752

114-2229

100-7846

100-7846

9T-3138

9T-3138

6E-5220

6E-5220

112-1770

125-7894

125-7894

125-7894

125-7894

6E-0289

112-1770

No. Part Rem

0R-2801

0R-2711

0R-2709

10R-0198

10R-0198

0R-8979

0R-8979

0R-8979

0R-8979

an R od

(In.) ngth ylind er Le

2.37

Rod No. Assemb lyPa rt

134-2659

134-2659

109-7022

109-7022

9T-0803

9T-0803

126-6953

126-6953

126-6953

125-7894

6E-0289

164-7176

9T-0661

9T-4008

6E-3704

6E-2498

6E-1502

6E-3704

6E-1502

9T-0752

9T-0752

No. Part Rem

0R-8975

0R-8975

10R-0196

10R-0196

0R-8979

0R-2707

0R-8965

0R-8982

0R-8982

0R-2709

0R-2709

an R od

(In.) ngth ylind er Le

9.17

Rod No. Assemb lyPa rt

166-8131

166-8132

164-7176

119-2110

119-2110

9T-4008

9T-4008

9T-4008

159-5848

9T-0752

114-2229

125-7894

125-7894

125-7894

125-7894

125-7894

6E-0289

134-2659

134-2659

109-7022

No. Part Rem

10R-0640

0R-8965

0R-8965

0R-8965

10R-0635

0R-2709

0R-8979

0R-8979

0R-8979

0R-8979

0R-8979

0R-8975

0R-8975

an R od

(In.) ngth ylind er Le

37.22

Rod No. Assemb lyPa rt

9T-4787

162-8059

9T-6407

9T-6407

9T-3180

9T-3180

9T-3180

184-2365

184-2365

125-7894

125-7894

125-7894

125-7894

134-2659

134-2659

126-6953

235-9835

235-9835

134-2659

166-8131

166-8132

No. Part Rem

0R-8979

0R-8979

0R-8979

0R-8979

0R-8975

0R-8975

0R-8975

10R-0640

an R od

(In.) ngth ylind er Le

42.80

Rod No. Assemb lyPa rt

9T-2821

9T-2821

126-0240

112-5734

9T-4787

162-8059

9T-6332

9T-6332

9T-6407

163-9261

9T-6407

9T-6332

9T-3180

9T-3169

100-7846

100-7846

9T-3138

9T-3138

6E-5220

6E-5220

112-1770

112-1770

No. Part Rem

10R-0126

10R-0126

10R-0126

10R-0198

10R-0198

an R od

(In.) ngth ylind er Le

2.40

Rod No. Assemb lyPa rt

1U-2086

1U-2086

1U-2086

1U-2086

9T-1805

9T-1805

7J-9357

9T-1805

9T-1805

7J-9357

7J-9357

4J-9723

9T-3169

100-7846

100-7846

9T-3138

9T-3138

6E-5220

No. Part Rem

0R-1182

0R-1182

0R-1182

0R-1182

0R-1182

0R-1182

0R-1182

10R-0198

10R-0198

an R od

(In.) ngth ylind er Le

2.40

Rod No. Assemb lyPa rt

3G-0883

1U-1997

3G-0883

3G-0883

4J-8070

4J-8070

9T-1805

9T-1805

7J-9357

7J-6248

7J-6248

4J-8070

7J-9357

7J-6248

7J-6248

149-5554

192-5908

No. Part Rem

0R-1182

0R-1182

0R-1182

0R-1182

an R od

(In.) ngth ylind er Le

51.34

Rod No. Assemb lyPa rt

215-9108

215-9095

215-9072

215-9108

215-9095

215-9072

139-3314

226-4016

210-9238

210-9236

210-9238

210-9236

139-3314

226-4016

210-9238

210-9236

210-9238

210-9236

7J-9715

4J-9723

Cylinder length is from open end to centerline of eye.

10R-0053

10R-0053

Rod No. Assemb lyPa rt

160-7931

160-7936

223-1071

171-7598

188-2082

189-0163

188-9970

189-0163

188-9970

160-6921

189-1829

189-0163

Rod No. Assemb lyPa rt

160-6921

223-1071

171-7598

188-2082

223-1071

160-7936

171-7598

188-2082

223-1071

160-7936

171-7598

No. Part Rem

an R od

(In.) ngth C

ylind er Le

Cylinder length is from open end to centerline of eye.

10R-2327

10R-2327

10R-2327

Rod No. Assemb lyPa rt

174-7124

174-6072

174-7130

160-6921

223-1071

223-1071

171-7598

188-2082

185-6261

160-7931

171-7598

171-7598

160-6921

Cylinder length is from open end to centerline of eye.

6.00

6.00

Rod No. Assemb lyPa rt

7J-3346

139-7550

1U-1057

1U-1057

7J-3346

1U-1057

1U-1057

7J-3346

8J-1564

8J-1564

139-7550

9T-2737

9T-2737

9T-2737

9T-2737

1U-1057

1U-1057

7J-3346

1U-1057

1U-1057

7J-3346

9T-2727

No. Part Rem

0R-8580

0R-1171

0R-1171

0R-1171

0R-1171

0R-3074

0R-3074

0R-8580

0R-1171

0R-1171

0R-1171

0R-1171

an R od

(In.) ngth ylind er Le

16.75

Rod No. Assemb lyPa rt

203-2744

Rod No. Assemb lyPa rt

206-5158

206-5158

203-2744

149-3471

149-3471

1U-1058

1U-1058

9J-8072

1U-1058

1U-1058

9J-8072

8J-2403

8J-2403

1U-1058

1U-1058

No. Part Rem

0R-1351

0R-1351

0R-1351

0R-1351

0R-3075

0R-3075

0R-1351

0R-1351

an R od

(In.) ngth ylind er Le

25.77

Rod No. Assemb lyPa rt

119-5275

4I-5699

209-2920

105-7490

4I-3859

121-1523

4I-3922

6E-0370

109-5792

109-5792

6E-0449

4T-1661

6E-1455

4T-0498

6E-3291

6E-0370

6E-0368

6E-1097

4T-1677

168-4846

Cylinder length is from open end to centerline of eye.

10R-0042

10R-0035

C

26.04

Rod No. Assemb lyPa rt

228-7939

228-1641

216-3873

205-7712

232-1683

205-7227

183-3097

168-1841

168-1862

138-2273

138-2273

143-0011

143-7091

139-3860

125-3332

156-0698

155-2947

117-6501

117-6501

6E-5757

116-3521

No. Part Rem

10R-1812

0R-9309

0R-8157

0R-8157

an R od

(In.) ngth ylind er Le

79.88

Rod No. Assemb lyPa rt

135-6767

107-9633

135-7793

124-5277

108-5963

107-6236

6E-5813

106-4984

106-4984

106-4984

106-4984

157-8534

157-8534

124-5281

120-5817

103-6042

103-6042

157-8534

155-2947

117-6501

No. Part Rem

0R-8160

0R-8154

0R-8154

0R-8158

0R-8155

0R-8155

0R-8155

0R-8155

0R-8159

0R-8159

0R-8159

0R-8159

0R-9309

0R-8157

an R od

(In.) ngth ylind er Le

31.50

Rod No. Assemb lyPa rt

114-4119

122-9125

119-1037

6E-6433

130-5988

130-7764

124-5828

124-5828

120-5814

108-7981

139-3788

136-4578

124-6471

119-4718

136-4577

136-4577

139-3790

124-6053

119-5811

119-4718

108-3555

No. Part Rem

0R-8164

0R-8163

0R-8161

0R-8161

0R-8161

0R-8165

0R-8165

0R-8165

an R od

(In.) ngth ylind er Le

118.31

Rod No. Assemb lyPa rt

130-7613

124-5231

124-5232

124-5232

114-4119

122-9125

119-1037

6E-6433

130-5988

130-7764

124-5828

157-8548

157-8548

135-7333

124-6468

114-5493

157-8548

157-8548

No. Part Rem

0R-8162

0R-8166

0R-8166

0R-8164

0R-8163

0R-8167

0R-8167

0R-8167

0R-8167

0R-8167

0R-8167

an R od

(In.) ngth ylind er Le

112.91

Rod No. Assemb lyPa rt

6E-3109

6E-3109

9T-7355

9T-6502

9T-6502

6E-3104

9T-6418

6E-3109

9T-7355

8J-9218

9T-6502

9T-6502

8J-9909

6E-3104

9T-6418

6E-3109

6E-3109

9T-7355

9T-6502

9T-6502

6E-3104

9T-6418

No. Part Rem

0R-8284

0R-8284

0R-4494

0R-4494

0R-8284

0R-4494

0R-4494

0R-8284

0R-8284

0R-4494

0R-4494

an R od

(In.) ngth ylind er Le

49.26

Rod No. Assemb lyPa rt

9J-7004

9J-7004

6E-2865

6E-2859

9T-4146

9T-4146

6E-2865

9J-7004

9J-7004

6E-2865

8J-2547

8J-2547

3G-2941

3G-2941

3G-2941

No. Part Rem

0R-3566

0R-3566

0R-3566

0R-3567

0R-3567

0R-3566

0R-3566

0R-3566

0R-3566

0R-1283

0R-1283

0R-1283

an R od

(In.) ngth ylind er Le

55.75

Rod No. Assemb lyPa rt

6E-2865

9T-4146

9T-4146

6E-2865

9J-7004

9J-7004

6E-2865

8J-2547

8J-2547

3G-2941

3G-2941

3G-2941

3G-9239

9T-4146

9T-4146

No. Part Rem

0R-3566

0R-3567

0R-3567

0R-3566

0R-3566

0R-3566

0R-3566

0R-1283

0R-1283

0R-1283

0R-3567

0R-3567

an R od

(In.) ngth ylind er Le

73.75

Rod No. Assemb lyPa rt

9J-4098

6E-5469

6E-5469

6E-4571

4T-8016

4T-8016

6E-5595

9J-4098

9J-4098

6E-5595

9J-8121

9J-8121

6E-3072

4T-1685

9J-2154

9J-2154

9J-2154

8J-8699

8J-8699

8J-8699

8J-8699

8J-8699

No. Part Rem

0R-1188

0R-3563

0R-3563

0R-8431

0R-1188

0R-1188

0R-8431

an R od

(In.) ngth ylind er Le

63.63

Rod No. Assemb lyPa rt

9J-7863

9J-8152

9J-8152

6E-5469

6E-5469

6E-4571

4T-8016

4T-8016

6E-5595

9J-4098

9J-4098

6E-5595

9J-8121

9J-8121

6E-3072

4T-1685

6E-3072

6E-3073

4T-1993

4T-1685

6E-3073

6E-5097

No. Part Rem

0R-3563

0R-3563

0R-8431

0R-1188

0R-1188

0R-8431

0R-3685

an R od

(In.) ngth ylind er Le

88.45

Rod No. Assemb lyPa rt

6E-5097

6E-5097

9T-1390

9T-1390

4T-1856

8J-8735

9J-7863

9J-8152

9J-8152

6E-5469

6E-5469

6E-4571

4T-8016

4T-8016

6E-5595

9J-4098

9J-4098

6E-5595

9J-8121

9J-8121

6E-3072

4T-1685

6E-2838

No. Part Rem

0R-3685

0R-3685

0R-1187

0R-1187

0R-3563

0R-3563

0R-8431

0R-1188

0R-1188

0R-8431

0R-8281

an R od

(In.) ngth ylind er Le

64.75

Rod No. Assemb lyPa rt

9J-7236

9J-7236

9J-2127

9J-2127

9J-2127

9J-2127

9J-7236

6E-5097

9T-1390

9T-1390

6E-5097

6E-5097

6E-5097

9T-1390

9T-1390

9J-7863

9J-8152

9J-8152

6E-5469

6E-5469

6E-4571

No. Part Rem

0R-1551

0R-1551

0R-4108

0R-4108

0R-4108

0R-4108

0R-1551

0R-3685

0R-1187

0R-1187

0R-3685

0R-3685

0R-3685

0R-1187

0R-1187

0R-3563

0R-3563

an R od

(In.) ngth ylind er Le

84.82

Rod No. Assemb lyPa rt

6E-4571

4T-8016

4T-8016

9T-4147

9T-4147

9J-8039

9J-8039

9J-2127

9J-7236

9J-7236

9J-2127

9J-2127

9J-2127

9J-2127

9J-7236

9T-1391

9T-1391

9T-1391

3G-5391

8J-8823

6E-5094

No. Part Rem

0R-1554

0R-1554

0R-4108

0R-1551

0R-1551

0R-4108

0R-4108

0R-4108

0R-4108

0R-1551

0R-3594

an R od

(In.) ngth ylind er Le

90.62

Rod No. Assemb lyPa rt

3G-1310

6E-5094

4T-5879

6E-4571

3G-4613

9J-5508

9J-9395

9J-2137

6E-5469

6E-5469

6E-4571

4T-8016

4T-8016

9T-4147

9T-4147

9J-8039

9J-8039

9J-2127

9J-7236

9J-7236

No. Part Rem

0R-3594

0R-1569

0R-1558

0R-1554

0R-3563

0R-3563

0R-1554

0R-1554

0R-4108

0R-1551

0R-1551

an R od

(In.) ngth ylind er Le

59.81

Rod No. Assemb lyPa rt

166-8125

162-5853

146-9019

147-0891

147-2636

147-3124

231-5817

231-1901

226-9960

219-1781

212-6357

219-1786

212-6356

219-1785

212-6355

219-1784

212-6354

212-6354

219-1782

212-6350

147-4432

166-8125

162-5853

No. Part Rem

an R od

(In.) ngth ylind er Le

24.15

Rod No. Assemb lyPa rt

151-2463

241-0327

237-3545

231-5817

231-1901

226-9960

212-6360

219-1780

212-6359

219-1840

212-6358

212-6353

219-1783

212-6352

151-3189

193-4651

150-9213

172-4225

No. Part Rem

an R od

(In.) ngth ylind er Le

27.94

Rod No. Assemb lyPa rt

307B

307

Model

C

00 - up 00 - up 00 - up 00 - up 00 - up 00 - up

Boom

Boom

Boom

Boom

Boom

Bucket

Rod length is from rod end to centerline of eye.

00 - up

00 - up

Stick

Boom

00 - up

Stick

00 - up

00 - up

Stick

00 - up

00 - up

Offset

Blade

00 - up

Blade

00 - up

N/A

Offset

00 - up

00 - up

Bucket

Blade

00 - up

Boom

00 - up

103-8195

00 - up

Blade

Blade

105-7238

00 - up

Blade

133-6765

185-9089

185-9088

169-6721

150-5901

143-7980

133-6759

165-4338

165-4337

162-4835

123-1627

125-1494

105-7437

103-8320

123-9937

105-7468

185-9087

114-8378

114-8377

107-6472

00 - up

107-6377

Blade

Eng Chanineering D ge L evel esign

00 - up

Cyli Part nder Ass No. emb ly

105-7239

143-8010

103-8196

169-6722

123-9938

143-8010

103-8196

114-8380

114-8379

162-4836

123-1631

125-1495

105-7438

103-8321

123-9938

105-7469

103-8196

105-7239

103-8196

114-8380

114-8379

107-6473

107-6378

r Rem Par an Sta n t d N a o rd C . ylind e

3.15

4.33

4.33

4.33

3.94

4.33

4.33

3.55

3.55

4.72

4.72

3.55

3.55

3.57

3.94

3.94

4.33

3.15

4.33

C

41.26

44.86

52.03

49.19

30.47

44.86

52.03

14.72

14.72

18.62

18.62

46.34

43.66

49.72

30.47

28.11

52.03

41.26

52.03

14.72

14.72

12.52

r>Pa rt

105-7246

143-8012

103-8201

143-8012

123-9940

143-8012

103-8201

111-5474

111-5474

123-1628

123-1628

105-7442

105-7442

103-8336

123-9940

105-7474

103-8201

105-7246

103-8201

111-5474

111-5474

107-6384

107-6384

No. Part Rem

0R-8224

0R-8223

0R-8223

0R-8225

0R-8223

0R-8224

0R-8223

an R od

(In.) ngth ylind er Le

14.72

Rod No. Assemb lyPa rt

170-9940

170-9945

170-9945

121-1411

121-1411

121-1411

137-3700

137-3700

119-5452

121-1401

121-1401

121-1401

103-8444

6I-6820

125-1592

4I-7655

137-3700

125-1586

6I-6811

125-1590

215-9946

215-9943

No. Part Rem

0R-8276

0R-8276

0R-8276

0R-4861

0R-4861

0R-8275

0R-8275

0R-8275

0R-4861

0R-4861

an R od

(In.) ngth ylind er Le

Cylinder length is from open end to centerline of eye.

10R-0040

10R-0040

10R-0040

0R-8274

0R-8274

0R-8274

0R-4832

10R-0040

0R-4832

0R-8273

0R-8273

Rod No. Assemb lyPa rt

137-3700

119-5452

162-4761

162-4761

114-8522

134-7823

125-1897

125-1897

114-8522

125-1897

125-1897

114-8522

173-3356

229-1047

209-5904

173-3356

184-7657

170-9940

173-3349

170-9945

170-9945

119-5441

119-5441

No. Part Rem

0R-4861

0R-4862

0R-4862

an R od

(In.) ngth ylind er Le

61.22

Rod No. Assemb lyPa rt

127-6053

127-6053

114-0475

127-6061

127-6057

127-6061

127-6057

107-6646

105-7389

127-6048

127-6048

105-7343

229-1047

209-5904

173-3356

194-8232

170-9940

170-9945

170-9945

200-3354

173-3356

No. Part Rem

0R-8272

0R-8272

0R-8271

0R-8271

0R-8270

an R od

(In.) ngth ylind er Le

Cylinder length is from open end to centerline of eye.

0R-8269

0R-8269

0R-8269

0R-8268

0R-8268

0R-8268

4.33

4.33

4.33

3.94

4.72

4.72

Rod No. Assemb lyPa rt

133-6667

184-7657

133-6712

185-9214

133-6683

133-6712

133-6683

133-6649

133-6649

127-6053

127-6053

114-0475

127-6061

127-6057

127-6061

127-6057

107-6646

105-7389

127-6048

127-6048

105-7343

No. Part Rem

10R-0187

0R-8272

0R-8272

0R-8271

0R-8271

0R-8270

an R od

(In.) ngth ylind er Le

61.30

Rod No. Assemb lyPa rt

7I-7297

4I-7655

4I-7655

137-3700

125-1586

127-6089

185-7864

106-7756

158-9122

127-6095

087-5508

165-9233

204-3695

185-0225

177-2613

209-5962

209-5971

209-5956

200-3405

No. Part Rem

0R-4864

0R-4861

0R-4861

0R-4861

0R-7341

0R-3832

an R od

(In.) ngth ylind er Le

Cylinder length is from open end to centerline of eye.

0R-4838

0R-4832

0R-9156

10R-0040

0R-4832

0R-3597

0R-3837

0R-3837

0R-3837

10R-0072

4.72

Rod No. Assemb lyPa rt

123-2126

119-5232

119-5225

119-5217

119-5203

133-6834

133-6832

133-6825

129-8023

119-5203

119-5203

119-5232

119-5225

4I-7655

4I-7655

165-9233

137-3700

137-3700

125-1586

123-2126

123-2045

No. Part Rem

0R-9063

0R-9172

0R-9166

0R-9168

0R-9170

0R-9170

0R-9170

0R-9172

0R-9166

0R-4861

0R-4861

0R-4861

0R-4861

0R-9063

an R od

(In.) ngth ylind er Le

50.94

Rod No. Assemb lyPa rt

133-6834

133-6832

133-6825

4I-7655

170-9940

165-9233

137-3700

125-1586

185-7864

158-9122

123-2120

165-9230

165-9228

165-9230

126-2005

126-2003

103-8381

170-5584

165-9233

185-7864

No. Part Rem

0R-4861

0R-4861

0R-3832

0R-9069

0R-7374

0R-3608

an R od

(In.) ngth ylind er Le

Cylinder length is from open end to centerline of eye.

0R-9062

0R-4832

10R-0040

0R-4832

10R-0072

10R-0063

0R-9066

10R-0034

0R-9065

10R-0072

Rod No. Assemb lyPa rt

127-6095

087-5508

165-9230

165-9228

170-5584

177-2599

214-1597

185-0198

194-8362

165-9233

204-3695

No. Part Rem

0R-7374

an R od

(In.) ngth ylind er Le

Cylinder length is from open end to centerline of eye.

0R-3837

0R-3837

10R-0034

5.51

5.12

4.72

Rod No. Assemb lyPa rt

7I-7297

127-6089

7I-1354

211-3075

6C-9384

165-9230

165-9228

216-0022

216-0022

185-0198

204-3695

177-2613

177-2610

177-2599

177-2575

185-0198

177-2613

177-2610

177-2599

177-2575

165-9233

158-9122

No. Part Rem

0R-4864

0R-7341

0R-4863

0R-7374

0R-3832

an R od

(In.) ngth ylind er Le

60.00

Rod No. Assemb lyPa rt

171-3380

171-3380

126-1889

119-5319

119-5309

119-5232

126-1889

119-5319

119-5309

119-5232

133-6832

126-1889

119-5319

119-5309

119-5309

119-5232

4I-7655

185-0329

137-3700

7Y-5157

125-1586

No. Part Rem

0R-9172

0R-9172

0R-9172

0R-9172

0R-9172

0R-4861

0R-4861

0R-3607

an R od

(In.) ngth ylind er Le

49.49

Rod No. Assemb lyPa rt

165-9233

185-0329

185-0193

185-0182

204-3695

204-3695

188-4187

188-4185

188-4180

177-2613

194-8328

188-4187

188-4185

188-4180

177-2613

179-9768

188-4215

188-4187

188-4185

188-4180

177-2613

No. Part Rem

0R-7343

an R od

(In.) ngth ylind er Le

51.89

Rod No. Assemb lyPa rt

4I-7655

151-9607

165-9233

156-0738

149-7612

7Y-5157

123-2126

123-2045

127-6089

7Y-5157

211-3075

6C-9384

175-6864

106-7756

7Y-4914

123-2120

123-2056

121-1545

121-1545

121-1545

103-8381

116-9125

No. Part Rem

0R-4861

0R-3607

0R-9063

0R-7341

0R-3607

0R-4866

0R-9069

0R-8488

0R-9067

0R-9067

0R-9067

0R-3608

an R od

(In.) ngth ylind er Le

73.50

Rod No. Assemb lyPa rt

194-8352

191-5629

191-5563

185-0198

194-8362

194-8352

194-8321

191-5735

179-9768

188-4215

185-0198

125-0025

125-0025

151-9607

170-9940

165-9233

156-0738

7Y-5157

175-6864

4Z-6131

191-3119

No. Part Rem

10R-0030

10R-0030

0R-3607

0R-4867

an R od

(In.) ngth ylind er Le

66.42

Rod No. Assemb lyPa rt

188-4215

109-5792

109-5792

151-9607

165-9233

156-0738

123-2105

7Y-5157

127-6089

123-2105

7Y-5157

106-7756

137-9382

7Y-4914

132-7897

7Y-4914

118-3945

103-8346

7Y-5157

No. Part Rem

10R-0123

10R-0123

0R-9073

0R-3607

0R-7341

0R-9073

0R-3607

0R-4866

0R-4866

0R-3607

an R od

(In.) ngth ylind er Le

58.43

Rod No. Assemb lyPa rt

127-6089

123-2105

155-9178

129-7885

106-7756

129-7885

132-7904

162-5822

222-8774

162-5822

216-2730

214-1597

165-9233

185-7864

7Y-5157

188-4215

123-2105

191-5629

191-5563

123-2105

191-5629

No. Part Rem

0R-7341

0R-9073

0R-7357

0R-3607

0R-9073

0R-9073

an R od

(In.) ngth ylind er Le

Cylinder length is from open end to centerline of eye.

0R-9173

0R-9070

0R-7367

0R-9159

0R-9159

10R-0072

Rod No. Assemb lyPa rt

143-8053

147-5748

147-5713

155-9178

156-0675

103-8354

156-0731

156-0738

156-0675

4I-1522

6E-3534

7Y-5108

4I-3802

151-9607

151-9607

156-0738

156-0731

4I-1522

191-3119

150-4124

150-4124

129-7898

118-3945

No. Part Rem

0R-7359

0R-7358

0R-7342

0R-7357

0R-4872

0R-4872

0R-4872

0R-4869

0R-9074

0R-3605

0R-4869

0R-4867

an R od

(In.) ngth ylind er Le

66.42

Rod No. Assemb lyPa rt

116-3521

116-3521

151-9607

151-9607

156-0738

156-0698

156-0695

116-3512

116-3512

142-5151

116-3515

179-9795

147-5729

156-0680

142-5151

147-5729

129-7898

162-5822

4I-5699

156-0680

234-8228

No. Part Rem

0R-4874

0R-4874

0R-4877

10R-0201

an R od

(In.) ngth ylind er Le

Cylinder length is from open end to centerline of eye.

0R-4854

0R-4854

0R-4848

0R-4848

0R-4848

0R-4854

0R-4856

0R-4852

0R-4858

0R-4858

0R-7373

0R-9161

0R-9159

Rod No. Assemb lyPa rt

121-1992

120-6310

120-6310

136-6031

118-4983

172-1028

136-6030

118-4982

147-5729

162-5822

233-6852

162-5822

155-9171

209-6043

173-3363

155-9171

155-9162

155-9153

155-9087

179-9795

No. Part Rem

10R-0201

an R od

(In.) ngth ylind er Le

Cylinder length is from open end to centerline of eye.

0R-7373

0R-7373

Rod No. Assemb lyPa rt

172-1026

136-6026

113-7321

183-8927

183-8926

183-8925

183-8924

183-8923

183-8986

183-8973

183-8927

183-8926

183-8925

158-6379

137-6214

No. Part Rem

an R od

(In.) ngth ylind er Le

57.13

Rod No. Assemb lyPa rt

209-0212

Rod No. Assemb lyPa rt

9T-7214

9T-9316

9T-7214

9T-7214

6E-5977

6E-5974

6E-5983

6E-5983

6E-5904

6E-5904

9T-5297

9T-5297

9T-4196

9T-7214

9T-7214

9T-9316

9T-7214

9T-7214

6E-5977

6E-5974

No. Part Rem

an R od

(In.) ngth ylind er Le

22.28

Rod No. Assemb lyPa rt

9T-5036

4T-7436

1U-3326

3G-6561

3G-6561

3G-6561

111-6249

111-6249

108-9329

111-6248

111-6248

No. Part Rem

10R-0609

0R-2704

0R-2713

0R-2495

0R-2495

0R-2495

an R od

(In.) ngth ylind er Le

40.32

Rod No. Assemb lyPa rt

3G-3313

1U-3326

3G-6561

3G-6561

3G-6561

3G-2983

3G-2983

3G-2983

9T-5493

3G-3313

3G-2983

3G-2983

3G-2983

9T-7029

9T-4067

9T-4067

No. Part Rem

0R-2494

0R-2713

0R-2495

0R-2495

0R-2495

0R-2493

0R-2493

0R-2493

0R-2799

0R-2494

0R-2493

0R-2493

0R-2493

10R-0125

10R-0125

an R od

(In.) ngth ylind er Le

31.64

Rod No. Assemb lyPa rt

214-1597

203-3909

201-6794

191-5735

7Y-5157

175-6864

123-2056

185-7362

136-3883

163-0327

119-5957

125-0025

125-0025

115-6968

139-3314

105-0106

114-8136

105-0106

133-8778

133-8778

No. Part Rem

0R-3607

0R-8488

0R-7380

10R-0030

10R-0030

10R-0127

10R-0128

10R-0117

10R-0128

an R od

(In.) ngth ylind er Le

41.10

Rod No. Assemb lyPa rt

113-7756

9T-2894

8J-6378

3G-5486

9T-2456

9T-2456

8J-6901

8J-6901

9T-2463

8J-6666

3G-5485

8J-6681

9T-4213

9T-2449

8J-6668

4J-6172

5J-1943

4J-8988

9J-5639

Cylinder length is from open end to centerline of eye.

0R-9125

0R-0994

0R-1878

0R-8577

0R-1148

0R-1148

0R-1267

10R-0050

10R-0050

4.75

3.50

5.00

5.50

Rod No. Assemb lyPa rt

4J-4769

9J-5639

4J-4769

9T-2525

121-9245

9T-2387

9T-2387

112-9035

9T-4213

9T-2449

168-9110

113-7756

6E-1346

131-7195

123-3793

6E-1341

123-3793

No. Part Rem

0R-7355

0R-7355

10R-0129

0R-7352

0R-9126

0R-7354

0R-7354

an R od

(In.) ngth ylind er Le

21.26

Rod Dia

mete r (In.

2.49

2.50

2.49

2.00

2.00

1.50

1.50

1.75

1.75

1.75

1.75

2.00

2.00

1.50

2.00

2.00

2.00

engt

h (In .)

.

246-5917

228-1778

246-5916

246-5916

246-5916

246-5916

227-5350

227-5350

227-5350

227-5350

227-5350

227-5350

233-9205

238-4462

233-9204

238-4462

238-4462

238-4462

.030

233-9207

Cylinder length is from open end to centerline of trunnion.

31.64

31.52

31.64

12.76

12.47

14.84

14.84

44.98

23.57

23.64

24.36

26.55

32.26

19.25

58.26

54.67

58.26

Rod L

re Stan Diamdard Cy linde . (In. r Bo )

3.00

Rod No. Assemb lyPa rt

9J-0543

9J-0543

3G-7648

3G-7648

8J-5565

9J-5639

4J-4769

3G-1756

3G-1756

114-4781

114-4781

9J-4870

8J-6701

8J-6254

3G-5693

157-4693

6E-1049

9T-3194

8J-6014

8J-6014

3G-5692

No. Part Rem

an R od

0R-1401

0R-1401

0R-1529

10R-0121

10R-0121

10R-2321

10R-2321

0R-1553

0R-3068

0R-1408

0R-1408

Rod Dia

mete r (In.

1.50

1.50

1.50

1.50

2.50

2.50

2.49

2.50

2.50

2.50

2.50

1.75

1.75

2.25

2.25

2.25

2.00

2.00

2.25

2.25

2.25

2.25

engt

h (In .)

.

246-5912

246-5912

246-5912

246-5912

242-2548

242-2542

243-0386

243-0384

240-2016

240-2016

240-2016

241-0900

241-0900

233-9205

233-9205

241-0900

241-0900

241-0900

.030

243-0385

241-7582

241-7582

233-9207

233-9207

241-7582

241-7582

241-7582

Cylinder length is from open end to centerline of trunnion.

16.69

16.69

17.24

17.24

70.38

31.52

31.64

32.41

32.41

33.76

33.76

25.41

25.41

28.73

28.69

27.89

22.28

22.28

51.47

51.47

51.43

51.43

Rod L

(In.) ngth ylind er Le

Cylinder length is from open end to centerline of eye.

0R-1794

0R-1795

0R-1874

10R-0110

0R-1845

0R-1845

10R-0101

0R-3114

0R-3114

0R-1797

0R-1797

Rod No. Assemb lyPa rt

6J-9730

3D-4742

3D-4742

5J-1926

9J-5639

4J-4769

6J-5842

6J-5842

9T-3218

121-9246

9T-2804

9T-2804

9T-2804

9T-2804

6E-1047

6E-1047

6E-1047

9T-3207

114-4781

114-4781

157-4693

184-6805

No. Part Rem

10R-0031

10R-0031

10R-0031

10R-0031

0R-8302

0R-8302

0R-8302

10R-2321

10R-2321

an R od

(In.) ngth ylind er Le

23.50

Rod Dia

mete r (In.

1.50

1.50

1.50

2.00

2.50

2.49

2.50

2.50

2.00

2.00

1.75

1.75

1.75

1.75

2.50

2.50

2.50

2.50

2.50

2.50

2.25

engt

h (In .)

.

246-5910

240-8479

242-2553

246-5917

228-1778

240-5500

240-2484

240-5500

240-2484

186-4392

186-4392

242-2548

242-2548

243-0384

235-0355

228-1778

.030

Cylinder length is from open end to centerline of trunnion.

24.90

20.75

20.75

18.37

31.52

31.64

27.69

27.69

14.09

13.75

16.96

16.96

16.96

16.96

68.82

68.82

68.82

68.82

33.76

33.76

27.89

Rod L

re Stan Diamdard Cy linde . (In. r Bo )

3.50

Rod No. Assemb lyPa rt

9T-3194

6E-1043

6E-1043

9T-3107

6E-1050

6E-1050

9T-3053

9T-3495

8J-5464

3G-4758

4T-2662

4T-2662

9T-2848

9T-2848

9T-2848

9T-2848

8J-5513

8J-5513

3G-7603

3G-7603

8J-5565

Cylinder length is from open end to centerline of eye.

0R-3114

0R-3128

0R-1376

0R-1376

10R-0060

10R-0060

10R-0059

10R-0059

0R-1836

0R-1835

0R-1874

Rod No. Assemb lyPa rt

9T-4215

9T-2444

8J-8696

3D-6220

3R-9862

2D-0704

2D-0704

118-1953

118-1953

143-5990

163-5644

118-5205

118-5205

141-2918

117-9003

113-7756

117-8631

No. Part Rem

0R-9136

0R-9136

0R-9130

0R-9138

0R-9138

0R-9138

0R-9128

0R-9126

0R-9134

an R od

(In.) ngth ylind er Le

21.57

Rod Dia

mete r (In.

1.75

1.75

1.75

1.50

2.50

2.50

2.50

2.50

2.50

2.50

2.50

2.50

3.25

3.25

2.00

3.00

engt

h (In .)

.

227-5350

227-5350

240-2016

240-2016

246-5910

186-4382

186-4382

186-4327

186-4327

233-9205

228-1776

.030

233-9207

Cylinder length is from open end to centerline of trunnion.

17.76

17.81

18.97

16.28

21.00

21.00

17.76

17.76

19.67

27.36

27.36

27.36

110.50

115.62

26.55

52.93

Rod L

re Stan Diamdard Cy linde . (In. r Bo )

5.25

Rod No. Assemb lyPa rt

112-9035

9T-4213

9T-2449

168-9110

198-8306

6E-1857

9T-2456

131-7195

119-8666

119-8666

9T-4215

6E-2447

9T-4215

8J-6673

8J-6673

3G-4761

8J-6216

8J-6216

3G-8427

3G-8427

No. Part Rem

10R-0129

0R-7352

0R-0895

0R-0895

an R od

(In.) ngth ylind er Le

16.61

Rod Dia

mete r (In.

1.75

1.75

1.75

1.75

2.00

1.50

1.50

2.00

2.00

1.75

2.00

1.75

1.50

1.50

1.50

1.50

1.50

1.50

1.50

engt

h (In .)

.

227-5350

227-5350

227-5350

227-5350

227-5350

227-5350

238-4462

233-9204

233-9204

238-4462

238-4462

227-5350

228-1778

227-5350

246-5914

246-5914

246-5914

246-5911

246-5911

246-5911

246-5911

246-5911

.030

Cylinder length is from open end to centerline of trunnion.

44.98

23.57

23.64

24.36

30.52

19.09

19.25

55.38

55.38

17.76

20.25

17.76

13.16

13.16

13.16

15.30

15.30

15.30

15.30

Rod L

re Stan Diamdard Cy linde . (In. r Bo )

2.50

Rod No. Assemb lyPa rt

6E-1857

131-7195

119-8666

6E-2447

8J-6673

8J-6673

3G-4761

8J-6216

8J-6216

3G-8427

3G-8427

9T-2478

105-2095

9T-4213

9T-2449

8J-7323

3G-1849

168-9110

Cylinder length is from open end to centerline of eye.

10R-0054

0R-3127

0R-1124

0R-1124

0R-1125

0R-1125

0R-7394

0R-7394

0R-7396

3.00

3.00

3.00

Rod No. Assemb lyPa rt

8J-6216

3G-8427

3G-8427

9T-2478

105-2095

9T-4213

9T-2449

8J-7323

3G-1849

168-9110

9J-0392

9J-0392

113-7756

9T-2894

8J-6378

3G-5486

9T-2456

9T-2456

8J-6901

No. Part Rem

0R-0895

0R-0895

0R-7353

0R-7352

0R-9126

0R-1192

an R od

(In.) ngth ylind er Le

20.37

Rod Dia

mete r (In.

1.50

1.50

1.50

1.75

1.75

1.75

1.75

1.50

1.75

1.75

2.00

2.00

2.00

2.00

2.00

2.00

1.50

1.50

1.50

engt

h (In .)

.

246-5911

246-5911

246-5911

246-5911

246-5911

227-5350

227-5350

227-5350

227-5350

227-5350

246-5913

240-2016

227-5350

233-9205

240-6899

233-9205

238-4462

238-6661

238-6661

233-9204

185-6596

246-5912

.030

246-5921

233-9207

233-9207

Cylinder length is from open end to centerline of trunnion.

15.30

15.30

15.30

53.41

53.41

23.57

23.64

20.55

24.18

24.36

26.62

26.62

26.55

25.12

26.19

26.17

19.09

19.09

19.55

Rod L

re Stan Diamdard Cy linde . (In. r Bo )

2.75

Rod No. Assemb lyPa rt

121-9245

112-9035

9T-4213

9T-2449

168-9110

113-7756

173-5990

173-5990

6E-1346

131-7195

123-3793

9T-4213

137-6794

137-6794

9T-2525

121-9245

9T-2387

Cylinder length is from open end to centerline of eye.

0R-7394

0R-7394

0R-9125

10R-0057

10R-0076

0R-8131

2.25

Rod No. Assemb lyPa rt

9T-2449

168-9110

113-7756

173-5990

173-5990

6E-1346

131-7195

123-3793

6E-1341

123-3793

9T-4213

137-6794

137-6794

3G-4761

8J-6216

8J-6216

3G-8427

3G-8427

9T-2478

105-2095

No. Part Rem

0R-9126

0R-7354

0R-7354

0R-7352

0R-0895

0R-0895

0R-7353

an R od

(In.) ngth ylind er Le

65.12

Rod Dia

mete r (In.

1.75

1.75

2.00

2.00

1.50

2.00

2.00

2.00

1.75

1.87

1.87

1.50

1.50

1.50

1.50

1.50

1.75

1.75

engt

h (In .)

.

227-5350

227-5350

227-5350

233-9205

238-4462

233-9204

238-4462

238-4462

238-4462

227-5350

246-5926

246-5926

246-5914

246-5911

246-5911

246-5911

246-5911

246-5911

246-5911

227-5350

227-5350

.030

233-9207

Cylinder length is from open end to centerline of trunnion.

23.64

24.36

26.55

32.26

19.25

58.26

54.67

58.26

23.57

23.83

23.83

13.16

15.30

15.30

15.30

15.30

53.41

53.41

Rod L

re Stan Diamdard Cy linde . (In. r Bo )

3.00

Rod No. Assemb lyPa rt

121-9245

Cylinder length is from open end to centerline of eye.

15.17

17.09

Rod No. Assemb lyPa rt

776D

287B

287

277B

277

Model

Rod length is from rod end to centerline of eye.

02 - 03

N/A

00 - up

Tilt

00 - up

00 - up

Tilt

N/A

00 - up

Tilt

00 - up

Tilt

00 - up

00 - up

Tilt

Tilt

00 - up

Tilt

00 - up

00 - up

Tilt

00 - up

Tilt

00 - up

Tilt

Tilt

00 - up

00 - up

Tilt

Tilt

00 - up

Tilt

00 - up

00 - up

Tilt

00 - up

00 - up

Tilt

Tilt

00 - up

Tilt

Tilt

00 - up

Eng Chanineering D ge L evel esign

Tilt

Application

C

8J-8865

113-1824

230-3705

225-9521

177-1985

156-5512

154-5018

225-9521

190-8041

177-1985

156-5512

154-5018

225-9521

177-1985

156-5512

154-5018

225-9521

177-1985

156-5512

154-5018

142-9196

r Rem Par an Sta n t d N a o rd C . ylind e

Cyli Part nder Ass No. emb ly

r>Pa rt

8J-8902

Rod No. Assemb lyPa rt

7J-7526

7J-7527

5J-3343

5J-3343

7J-7685

9T-6079

9J-2542

9J-2542

9J-2541

9J-2541

101-0931

7J-3470

7J-3471

9J-2542

107-2656

7J-7526

110-0537

105-3360

105-3360

No. Part Rem

0R-3200

0R-8830

0R-8830

0R-3691

0R-3691

0R-8830

0R-8972

an R od

(In.) ngth ylind er Le

22.98

Rod No. Assemb lyPa rt

3G-1694

3G-1694

9J-4156

107-2657

7J-7526

7J-7527

6J-1205

4J-5582

7J-7859

5J-3343

5J-3343

7J-7859

6J-3071

5J-3343

4J-8762

4J-4733

No. Part Rem

0R-3690

0R-3690

an R od

(In.) ngth ylind er Le

21.45

Rod No. Assemb lyPa rt

8J-2321

8J-2321

7J-3470

7J-3471

7J-3471

7J-3438

7J-3360

7J-7526

110-0537

9T-6084

9J-4156

205-7075

4T-4166

4T-4166

107-2657

108-0993

No. Part Rem

0R-3691

0R-1539

0R-8342

0R-8827

0R-8827

an R od

(In.) ngth ylind er Le

18.43

Rod No. Assemb lyPa rt

7J-3471

7J-7685

9T-6079

9J-2542

9J-2542

9J-2541

9J-2541

101-0931

7J-3470

7J-3471

105-3360

105-3360

9T-6079

101-0931

7J-3470

7J-3471

107-2656

7J-7685

105-3360

105-3360

No. Part Rem

0R-3200

0R-8830

0R-8830

0R-3691

0R-3691

0R-3691

0R-3691

0R-8972

0R-3200

an R od

(In.) ngth ylind er Le

22.98

Rod No. Assemb lyPa rt

105-2444

105-2444

4T-4758

8J-9437

8J-9436

9T-5507

9T-3972

8J-8902

8J-8902

8J-9437

171-1236

4T-4758

8J-9437

171-1236

4T-4758

8J-9437

171-1236

4T-4758

8J-9437

171-1236

No. Part Rem

0R-8824

0R-3320

0R-1074

0R-8824

0R-8824

0R-8824

0R-8824

an R od

(In.) ngth ylind er Le

47.94

Rod No. Assemb lyPa rt

237-4989

203-9829

106-1806

4T-6799

4T-6100

4T-4766

237-4989

203-9829

106-1806

4T-6799

4T-6100

4T-4766

237-4989

203-9829

106-1806

1U-3179

1U-3179

No. Part Rem

10R-1346

0R-3198

0R-8818

10R-1346

0R-3198

0R-8818

10R-1346

an R od

(In.) ngth ylind er Le

Cylinder length is from open end to centerline of eye.

10R-1345

10R-1345

0R-3202

0R-8816

0R-3206

0R-3206

10R-1345

10R-1345

0R-3202

0R-8816

0R-3206

0R-3206

10R-1345

10R-1345

0R-3210

0R-3210

Rod No. Assemb lyPa rt

00 - up 00 - up 00 - up 00 - up 00 - up 00 - up

Tilt

Tilt

Tilt

Tilt

Tilt

Tilt

BG-240C

BG-230

00 - up

Tilt

BG-225C

Rod length is from rod end to centerline of eye.

00 - up

Tilt

00 - up

Tilt

00 - up

00 - up

Tilt

Tilt

00 - up

Tilt

00 - up

00 - up

Tilt

Tilt

00 - up

Tilt

00 - up

00 - up

Tilt

00 - up

00 - up

Tilt

Tilt

00 - up

Tilt

Tilt

00 - up

Tilt

00 - up

Tilt

BG-225B

00 - up

Tilt

Application

Eng Chanineering D ge L evel esign

BG-220B

Model

C

165-4654

135-9444

135-0217

133-8683

115-5207

206-6682

174-3073

174-3072

135-9444

135-0218

135-0217

133-8683

115-5207

107-0473

206-6682

174-3073

174-3072

135-9444

135-0218

133-8683

115-5207

135-0218

Rod No. Assemb lyPa rt

PM-565

PM-465

BG-2455C

BG-2255C

BG-270B

Model

00 - up 00 - up 00 - up 00 - up 00 - up

Tilt

Tilt

Tilt

Tilt

Tilt

00 - up 00 - up 00 - up

N/A

N/A

N/A

Rod length is from rod end to centerline of eye.

00 - up

N/A

00 - up

00 - up

Tilt

N/A

00 - up

Tilt

00 - up

00 - up

Tilt

N/A

00 - up

00 - up

Tilt 00 - up

00 - up

Tilt

Tilt

00 - up

Tilt

00 - up

Tilt

00 - up

Tilt

Tilt

00 - up

Eng Chanineering D ge L evel esign

Tilt

Application

C

122-2692

122-2691

086-9735

086-9600

204-5736

086-9735

174-3073

174-3072

165-4654

135-0220

135-0217

133-8683

133-0959

121-0412

113-9743

107-0473

206-6682

135-0220

135-0218

133-8683

135-0217

Rod No. Assemb lyPa rt

00 - up 00 - up 00 - up

N/A

N/A

N/A

N/A

SM-350

00 - up

00 - up

Rod length is from rod end to centerline of eye.

N/A

00 - up

00 - up

N/A

00 - up

00 - up

N/A

N/A

00 - up

N/A

N/A

00 - up

N/A

00 - up

00 - up

N/A

N/A

00 - up

N/A

RR-250B

RR-250

00 - up

00 - up

N/A 00 - up

00 - up

N/A

N/A

00 - up

N/A

N/A

00 - up

N/A

RM-350B

00 - up

Bucket

RM-350

00 - up

Bucket

Application

Eng Chanineering D ge L evel esign

RM-250C

Model

C

190-5477

087-1282

121-9825

087-1282

077-5316

216-0127

204-5737

204-5736

204-5735

204-5734

203-4380

203-4379

190-5477

190-5476

187-3859

109-7815

204-5735

204-5734

203-4380

190-5477

6E-3297

Cyli Part nder Ass No. emb ly

3.84

C

40.76

Rod No. Assemb lyPa rt

r Rem Par an Sta n t d N a o rd C . ylind e Cylinder length is from open end to centerline of eye.

9T-7337

No. Part Rem

an R od

re Stan Diamdard Cy linde . (In. r Bo )

Paving Products - Soil Stabilizers

6E-3296

Rod Dia

mete r (In.

2.75

engt

h (In .)

.

205-0125

1G-6745

098-3341

1G-6745

098-3341

224-7523

224-7521

225-0381

225-0380

225-0379

224-5524

224-5524

205-0125

205-0125

1G-6231

1G-6231

225-0380

225-0379

224-5524

205-0125

193-9270

1G-6745

.030

Cylinder length is from open end to centerline of trunnion.

41.05

Rod L

p Pa rt No . ylind er G rou

087-1282

dard

. t No t Par " O/S Seal Ki

t No t Par Seal Ki Stan

(In.) ngth ylind er Le

Paving Products - Road Reclaimers

Hydraulic Cylinders and Seals Sorted by MACHINE MODEL

267

)

00 - up 00 - up 00 - up 00 - up

Counterweight

Counterweight

Counterweight

N/A

Rod length is from rod end to centerline of eye.

00 - up

Counterweight

00 - up

Tilt

561B

00 - up

Tilt

CS-433E

00 - up

00 - up

Tilt

Tilt

00 - up

Tilt

00 - up

Tilt

CS-423E

CS-323C

00 - up

Tilt

00 - up

Tilt

CP-433E

00 - up

Tilt

CP-323C

00 - up

N/A 00 - up

00 - up

N/A

N/A

00 - up

00 - up

N/A

N/A

00 - up

SS-250B

SS-250

00 - up

N/A

Eng Chanineering D ge L evel esign

N/A

Application

C

3J-2017

3G-3505

3G-3504

1K-5894

1K-5893

186-0876

186-0681

186-0876

186-0681

077-6574

186-0876

186-0681

186-0681

077-6574

Rem Par an Sta n t d N a o rd C . ylind e

r Cyli Part nder Ass No. emb ly

3J-1717

3G-3503

3G-3502

1K-9946

1K-9945

4.50

4.50

4.50

4.50

4.50

C

20.02

31.11

31.11

29.50

29.50

r>Pa rt

2J-6369

3G-3330

3G-3330

1K-9674

1K-9674

Rod No. Assemb lyPa rt

4J-4629

4J-4629

3G-2925

133-3852

4T-8520

1M-3108

Rod No. Assemb lyPa rt

236

232B

00 - up 00 - up 00 - up 00 - up

Ripper

Ripper

Ripper

Ripper

Rod length is from rod end to centerline of eye.

00 - up

00 - up

Boom 00 - up

00 - up

Boom

Ripper

00 - up

Ripper

00 - up

Boom

00 - up

Boom

Boom

00 - up

Boom

00 - up

00 - up

Boom

Boom

00 - up

Boom

00 - up

00 - up

Boom

Boom

00 - up

Boom

00 - up

Boom 00 - up

00 - up

Boom

00 - up

Boom

Eng Chanineering D ge L evel esign

Boom

Application

C

225-9521

177-1985

156-5512

154-5018

142-9191

142-9190

230-3694

230-3684

225-9521

177-1985

156-5512

154-5018

225-9521

191-9641

177-9569

177-9568

177-1985

156-5512

154-5018

225-9521

177-9569

Rod No. Assemb lyPa rt

252

248B

248

00 - up 00 - up 00 - up 00 - up

Tilt

Tilt

Tilt

Tilt

Rod length is from rod end to centerline of eye.

00 - up

00 - up

Tilt

00 - up

00 - up

Tilt

Tilt

00 - up

Tilt

Tilt

00 - up

Tilt

00 - up

00 - up

Tilt

Tilt

00 - up

Tilt

00 - up

00 - up

Tilt

Tilt

00 - up

00 - up

Tilt

Tilt

00 - up

Tilt

00 - up

00 - up

Tilt

Tilt

00 - up

00 - up

Tilt

00 - up

Tilt

Eng Chanineering D ge L evel esign

Tilt

Application

C

225-9521

190-8041

177-1985

156-5512

154-5018

225-9521

177-1985

156-5512

154-5018

225-9521

177-9566

177-9565

177-1985

156-5512

154-5018

142-9196

142-9195

225-9521

177-1985

156-5512

154-5018

225-9521

Rod No. Assemb lyPa rt

8Q-5898

an R od P

art N o. Rem

0R-8965

Ro d D iame ter (I n.

1.50

1.97

1.97

Rod L

(In.)

235-0354

235-0354

180-9872

188-3880

8Q-6290

235-0354

235-0354

235-0354

089-8099

089-7459

089-8099

Cylinder length is from open end to centerline of trunnion.

15.71

16.30

16.30

engt h

re Stan Diamdard Cy linde . (In. r Bo )

3.94

Rod No. Assemb lyPa rt

9T-4008

Cylinder length is from open end to centerline of eye.

0R-8966

0R-8966

Rod No. Assemb lyPa rt

9T-4008

Rod No. Assemb lyPa rt

209-1757

208-3893

207-5073

9T-4008

224-5311

211-3446

210-6549

209-1757

208-3893

208-1622

207-5073

9T-4008

202-8914

202-8914

224-5311

207-2070

an R od P

art N o. Rem

0R-8965

0R-8965

Ro d D iame ter (I n.

1.50

1.50

Rod L

(In.)

235-0354

235-0354

235-0354

233-1014

235-0354

235-0354

235-0354

233-1014

Cylinder length is from open end to centerline of trunnion.

15.71

15.71

engt h

(In.) ngth C

ylind er Le

re Stan Diamdard Cy linde . (In. r Bo )

Cylinder length is from open end to centerline of eye.

0R-8966

0R-8966

0R-8966

0R-8966

Rod No. Assemb lyPa rt

3G-5773

3G-5773

3G-5902

3G-5769

4T-1690

8J-6907

8J-6907

8J-6907

8J-6907

7J-9917

7J-9917

7J-5890

7J-5890

7J-5890

7J-5890

Ro d D iame ter (I n.

2.00

2.00

2.25

2.25

1.75

2.00

2.00

2.00

2.00

2.00

2.00

2.00

2.00

2.00

2.00

Rod L

(In.)

233-9205

240-6899

240-6899

241-0903

241-0897

240-1671

246-5914

233-9205

240-6899

233-9205

240-6899

233-9205

240-6899

240-6899

233-9205

233-9205

233-9205

240-6899

240-6899

233-9205

240-6899

240-6899

233-9207

241-7581

233-9207

233-9207

233-9207

233-9207

233-9207

233-9207

233-9207

Cylinder length is from open end to centerline of trunnion.

42.13

42.13

47.72

44.63

46.71

25.38

25.38

25.38

25.38

16.39

16.39

33.05

33.05

33.05

33.05

engt h

re Stan Diamdard Cy linde . (In. r Bo )

4.00

Rod No. Assemb lyPa rt

2K-6827

4J-4674

4J-4674

4J-4629

4J-4629

141-9173

8J-5701

149-6066

136-8603

101-2491

7J-9917

7J-9917

101-2713

126-9526

101-2713

126-9526

8J-5389

4T-1690

Ro d D iame ter (I n.

2.00

2.00

2.00

2.00

2.00

2.00

2.00

2.00

1.75

1.75

2.00

2.00

2.00

2.00

2.00

2.00

1.50

1.75

Rod L

(In.)

233-9205

233-9205

240-1881

240-1881

233-9205

240-6899

240-6899

233-9205

233-9205

233-9205

233-9205

233-9205

233-9205

233-9205

233-9205

246-5914

240-1671

233-9207

233-9207

233-9207

233-9207

233-9207

233-9207

233-9207

233-9207

233-9207

233-9207

Cylinder length is from open end to centerline of trunnion.

32.31

26.00

26.00

36.31

36.31

32.54

32.31

18.37

44.98

44.23

16.39

16.39

32.25

32.25

32.25

32.25

18.25

46.71

engt h

re Stan Diamdard Cy linde . (In. r Bo )

3.25

Rod No. Assemb lyPa rt

101-2713

8J-5389

3G-5773

3G-5773

3G-5902

3G-5769

8J-5661

1K-9037

1K-9037

2K-7366

2K-6827

4J-4923

4J-4674

4J-4629

4J-4629

8J-5701

8J-5661

1K-9037

Rod No. Assemb lyPa rt

8J-6907

8J-6907

7J-9917

7J-9917

7J-5890

7J-5890

7J-5890

7J-5890

101-2713

101-2713

8J-5389

3G-5773

3G-5773

Rod No. Assemb lyPa rt

7J-9950

7J-9949

5J-7877

7J-9950

6J-3878

5J-9810

7J-9712

7J-9712

7J-9815

7J-9712

7J-9712

6J-1950

6J-2205

6J-1950

6J-2205

8J-5674

8J-5674

8J-5668

6J-2801

6J-5819

6J-2801

6J-2801

136-3169

an R od P

art N o. Rem

0R-1262

0R-1527

Ro d D iame ter (I n.

2.37

2.37

2.37

2.37

2.50

2.37

2.25

2.25

3.00

2.25

2.25

2.25

2.25

2.25

2.25

2.00

2.00

2.00

1.97

2.00

1.97

1.97

2.00

Rod L

(In.)

241-8925

241-8925

241-8925

241-8925

243-0381

241-0901

241-0901

241-0901

241-0901

241-0901

241-0901

241-0901

241-0901

237-8277

240-6899

240-6899

240-6899

240-6899

233-9205

233-9207

Cylinder length is from open end to centerline of trunnion.

43.50

43.50

43.50

43.50

21.00

43.50

42.78

42.78

52.63

42.78

42.78

42.78

43.29

42.78

43.29

31.76

31.76

20.88

20.88

27.42

20.88

20.88

45.10

engt h

re Stan Diamdard Cy linde . (In. r Bo )

4.00

Rod No. Assemb lyPa rt

3G-1294

3G-1294

6E-1048

9T-3618

4T-9384

4T-9384

3G-4644

3G-4644

3G-4644

3G-4644

3G-1294

3G-1294

9J-0538

9J-0538

9J-0538

4T-1966

4T-1966

8J-5668

4T-9384

4T-9384

an R od P

art N o. Rem

0R-1427

0R-1427

0R-1427

0R-1435

0R-1435

0R-1527

Ro d D iame ter (I n.

2.00

2.00

2.38

2.38

2.00

2.00

2.50

2.50

2.50

2.50

2.00

2.00

2.25

2.25

2.25

2.25

2.25

2.00

2.00

2.00

Rod L

(In.)

233-9205

240-6899

240-6899

233-9205

240-6899

243-5800

186-4350

243-5800

186-4350

233-9205

240-6899

240-6899

241-9297

241-0899

234-2591

241-9297

241-0899

240-6899

240-6899

233-9205

240-6899

233-9207

233-9207

233-9207

233-9207

Cylinder length is from open end to centerline of trunnion.

19.91

19.91

38.68

38.68

18.51

18.51

33.58

33.58

33.58

33.58

19.91

19.91

38.58

38.58

38.58

39.61

39.61

20.88

18.51

18.51

engt h

re Stan Diamdard Cy linde . (In. r Bo )

4.00

Rod No. Assemb lyPa rt

4T-9384

4T-9384

7J-9829

7J-9830

7J-9829

6J-2690

6J-2689

7J-9830

6J-3878

7J-9825

7J-9825

7J-9825

7J-9825

6J-2205

6J-2205

8J-5674

8J-5674

8J-5668

6J-2801

6J-5819

6J-2801

6J-2801

7J-9829

Rod No. Assemb lyPa rt

8J-5681

8J-5681

4J-4927

4J-4927

4J-4674

2K-6827

4J-4924

2K-3760

2K-3760

2K-3760

8J-5701

7Y-5108

6E-5187

1U-0538

3G-1294

3G-1294

6E-5187

9T-3611

9T-3611

4T-9384

4T-9384

6E-5187

an R od P

art N o. Rem

0R-3605

0R-1432

0R-1432

0R-1432

10R-0116

10R-0116

0R-1432

Ro d D iame ter (I n.

2.00

2.00

2.00

2.00

2.00

2.00

2.00

2.49

2.49

2.49

2.00

3.34

3.00

3.00

2.00

2.00

3.00

2.50

2.50

2.00

2.00

3.00

Rod L

(In.)

135-9059

244-0977

244-0977

233-9205

240-6899

240-6899

244-0978

186-4382

243-0398

233-9205

240-6899

244-0977

233-9207

233-9207

Cylinder length is from open end to centerline of trunnion.

25.84

25.84

28.06

28.06

26.00

32.31

28.06

35.97

35.97

35.97

32.31

63.03

36.02

36.02

19.91

19.91

36.02

40.88

40.88

18.51

18.51

36.02

engt h

re Stan Diamdard Cy linde . (In. r Bo )

5.50

Rod No. Assemb lyPa rt

5J-6340

8J-5711

8J-5711

8J-5711

8J-5711

8J-5711

8J-5711

8J-5688

6J-1676

6J-1676

4J-4632

4J-4632

6J-3878

2K-5368

8J-5688

8J-5681

8J-5681

4J-4927

4J-4927

4J-4674

2K-6827

Rod No. Assemb lyPa rt

8J-5724

8J-5724

8J-5718

8J-5688

7J-9632

7J-9632

7J-1732

6J-4502

6J-4502

5J-9997

7J-9639

7J-9639

7J-9639

5J-6340

8J-5711

8J-5711

8J-5711

8J-5711

8J-5711

8J-5711

8J-5688

Rod No. Assemb lyPa rt

4T-7397

3G-1189

232-6534

166-2283

166-2283

8J-5747

8J-5747

4T-7397

4T-7397

3G-1189

3G-1189

4T-2493

4T-2493

3G-8406

3G-8406

8J-5747

8J-5747

9T-8404

9T-8404

3G-0199

3G-0199

218-1819

an R od P

art N o. Rem

0R-3063

0R-1525

0R-1525

0R-3063

0R-3063

0R-1438

0R-1438

0R-1403

0R-1403

0R-1525

0R-1525

0R-2852

0R-2852

0R-1418

Ro d D iame ter (I n.

3.25

2.50

3.25

3.25

2.00

2.00

3.25

3.25

2.50

2.50

2.50

2.50

3.25

3.25

2.00

2.00

3.75

3.75

2.25

2.25

2.75

Rod L

(In.)

242-2542

240-6883

240-8479

206-2857

242-2542

243-0386

186-4378

186-4350

245-0606

240-6883

240-8479

245-9838

194-4393

241-7584

241-7584

193-7639

193-7639

243-0385

243-0385

241-7581

241-7581

Cylinder length is from open end to centerline of trunnion.

45.96

30.56

48.95

48.95

25.28

25.28

45.96

45.96

30.56

30.56

41.04

41.04

54.86

54.86

25.28

25.28

39.38

39.38

21.80

21.80

48.47

engt h

re Stan Diamdard Cy linde . (In. r Bo )

5.50

Rod No. Assemb lyPa rt

9J-7881

9J-7881

7J-9373

9J-7881

9J-7881

9J-7881

7J-9373

7J-1931

7J-1931

7J-1931

7J-1931

5J-5195

5J-5195

5J-5195

5J-5195

9J-7881

9J-7881

9J-7881

9J-7881

8J-5747

8J-5747

8J-5765

8J-5765

Rod No. Assemb lyPa rt

5J-5195

5J-5195

9J-7881

9J-7881

9J-7881

9J-7881

8J-5747

8J-5747

8J-5765

8J-5765

6J-7110

6J-1162

6J-1162

7J-9648

7J-9377

7J-9377

7J-9648

7J-9648

7J-9377

7J-9648

7J-9377

5J-5374

5J-9771

Rod No. Assemb lyPa rt

7J-9377

7J-9377

7J-9648

7J-9648

7J-9377

7J-9648

7J-9377

5J-5374

5J-9771

5J-5374

5J-9771

8J-5753

7J-2469

5J-9886

5J-7683

8J-5759

8J-5747

8J-5747

8J-5747

8J-5747

an R od P

art N o. Rem

0R-1305

0R-1305

0R-1533

0R-1533

0R-1305

0R-1533

0R-1305

0R-1525

0R-1525

0R-1525

0R-1525

Ro d D iame ter (I n.

2.79

2.79

2.75

2.75

2.79

2.75

2.79

2.75

2.75

2.75

2.75

2.25

2.25

2.25

2.50

2.25

2.00

2.00

2.00

2.00

Rod L

(In.)

244-0961

243-0386

243-0386

242-2549

241-0895

240-6883

240-8479

240-6883

240-8479

243-0380

241-7576

Cylinder length is from open end to centerline of trunnion.

55.11

55.11

55.11

55.11

55.11

55.11

55.11

55.11

55.10

55.11

55.10

37.20

33.36

37.20

32.24

31.24

25.28

25.28

25.28

25.28

engt h

re Stan Diamdard Cy linde . (In. r Bo )

5.00

Rod No. Assemb lyPa rt

9J-2064

9J-2064

7J-3242

8J-6059

8J-6059

8J-6059

8J-6059

8J-2359

9J-2064

8J-2359

9J-2064

6J-4335

6J-4336

6J-4335

6J-4335

6J-4336

6J-4335

8J-2359

9J-2064

7J-3242

8J-6059

Rod No. Assemb lyPa rt

9J-9820

139-0553

139-0553

139-0554

4T-8052

101-9237

101-9237

8J-0090

8J-0090

8J-0090

8J-6907

8J-6907

8J-6907

8J-6907

7J-9917

7J-9917

9T-6655

8J-7294

Rod No. Assemb lyPa rt

8J-0090

8J-6907

8J-6907

8J-6907

8J-6907

7J-9917

7J-9917

9T-6655

7J-9227

3G-5773

3G-5773

3G-5902

3G-5769

4T-8052

9J-9820

1J-1797

1J-1795

8F-2658

8F-0910

Rod No. Assemb lyPa rt

4T-1677

4T-1677

4T-1677

168-4846

100-4532

220-6337

8J-0090

193-1546

193-1546

201-1060

201-1060

141-2919

5J-1596

6J-3878

3G-1756

4H-6720

3G-2613

1K-9988

3G-0807

3G-2613

3G-0807

Rod No. Assemb lyPa rt

7J-9917

7J-9917

7J-9227

141-2919

4T-8052

9J-9820

139-0553

139-0553

4T-8052

7J-9701

8J-1777

8J-1777

2J-1424

7J-8294

7J-8294

7J-7977

8J-1777

8J-1777

3R-9152

4J-4832

9J-8174

Rod No. Assemb lyPa rt

246-8883

6E-0370

167-7555

160-7612

105-9825

152-6483

137-8458

106-1292

4T-1630

4T-2634

6E-1456

4T-1630

1U-4069

116-3084

9T-2714

3J-6441

3G-6895

3G-6895

9T-8426

6E-5450

9T-8426

Rod No. Assemb lyPa rt

8J-6866

7J-8294

7J-7977

5J-8159

5J-8160

4J-3732

4J-3733

8J-5447

8J-5447

2J-6369

2J-6369

2J-6370

2J-6370

4J-4832

2J-1424

9J-8174

1J-1797

1J-1795

Cylinder length is from open end to centerline of eye.

0R-1335

0R-1132

0R-3096

0R-1323

0R-1323

0R-1318

0R-1318

0R-1382

0R-1147

0R-1147

5.00

Rod No. Assemb lyPa rt

1U-4081

1U-4081

7J-3169

7J-3169

8J-1777

8J-1777

8J-1777

2J-1424

8J-6866

7J-3169

7J-3169

8J-1777

8J-1777

8J-1777

2J-1424

8J-6866

7J-3169

7J-9701

7J-3169

7J-3169

Rod No. Assemb lyPa rt

9T-2714

114-4304

114-4304

204-9542

160-0061

110-4768

116-3084

110-4768

9T-2714

228-0321

137-5106

110-3271

115-8219

110-3271

152-6486

110-3789

110-3789

204-9542

160-0061

110-4768

116-3084

110-4768

9T-2714

Rod No. Assemb lyPa rt

6J-9751

7J-9359

7J-9359

3J-6441

5J-7888

5J-7888

3J-6441

2J-1424

9J-4889

7J-3338

7J-3338

9J-4889

7J-3338

7J-3338

9J-4889

9J-4889

7J-3338

7J-3338

6J-9751

4J-6170

Rod No. Assemb lyPa rt

7J-6015

3J-6486

5J-2526

3J-2176

7J-6015

3J-6486

3J-4907

3J-2176

2J-3244

2J-0496

5J-2526

5J-2526

6J-8819

6J-8819

3J-4907

6J-1431

2J-3895

9T-6115

9T-6115

112-4818

147-0710

147-0710

112-4818

Rod No. Assemb lyPa rt

9T-0584

4T-3120

6E-3980

110-6808

8J-8687

9T-0336

6E-1901

6E-1111

6E-1111

6E-1111

6E-2190

6E-2190

4T-6838

147-6116

3G-6827

4T-3120

4T-0406

3G-8192

3G-8192

6E-2190

Rod No. Assemb lyPa rt

1J-5278

1J-5278

1J-5278

1J-5278

4T-3120

7J-0502

4J-5408

2J-1699

4J-2378

3J-4907

3J-3486

3J-1174

2J-1699

6J-7163

6J-7163

6J-8819

6J-8819

3J-1174

5J-3031

5J-3030

3J-3486

106-3881

Rod No. Assemb lyPa rt

4R-8812

147-6116

3G-6827

4T-3120

6E-3980

4R-8814

4T-0406

4R-8808

9J-6556

9J-6556

4T-8604

3G-3527

3G-3527

4T-3120

192-6448

192-6448

9J-6556

9J-6556

Rod No. Assemb lyPa rt

3G-6882

9J-0544

3G-6882

9J-0544

112-4055

110-6899

105-3667

3G-5764

112-4055

110-6899

105-3667

3G-5764

3G-5764

112-4055

110-6899

105-3667

3G-5764

6E-4859

6E-4859

6E-4859

6E-4859

6E-4859

Rod No. Assemb lyPa rt

9T-9682

105-4169

4T-9996

192-6448

192-6448

6E-3980

9J-6556

9J-6556

9T-2865

9T-2865

9T-2865

9T-9682

9T-4712

9T-1181

9T-9682

9T-9682

9T-4712

9T-1181

7J-9648

105-4169

4T-9996

192-6448

192-6448

Rod No. Assemb lyPa rt

4T-2763

6E-3914

6E-3914

4T-2763

112-4055

110-6899

105-3667

3G-5764

126-5509

126-5509

126-5509

126-5509

105-4170

9T-5885

102-0691

9J-1744

102-0691

9J-1744

3G-2217

102-0691

9J-1744

102-0691

9J-1744

Rod No. Assemb lyPa rt

8J-8803

7J-7294

4J-8070

4J-8070

9T-1805

9T-1805

7J-9357

4J-8070

7J-7027

7J-7304

7J-7288

7F-2357

7F-2357

1J-1797

1J-1795

1J-1795

1J-1797

111-5702

Rod No. Assemb lyPa rt

4J-9723

3J-6654

3J-4907

4J-7617

3J-4907

4J-7617

3J-4907

3J-4907

7J-2206

7J-2206

7J-2206

7J-2206

7J-2206

4J-6493

7J-9715

4J-9723

3J-6654

4J-7617

an R od P

art N o. Rem

0R-7356

0R-7356

0R-8932

0R-8932

0R-8932

0R-8932

0R-8932

0R-9220

0R-7356

Ro d D iame ter (I n.

2.00

2.25

2.50

2.50

2.50

2.50

2.50

2.50

2.50

2.50

2.50

2.50

2.50

2.50

2.25

2.00

2.25

2.50

Rod L

(In.)

241-0895

238-6882

242-2554

242-2554

242-2554

242-2554

242-2554

242-2554

242-2541

242-2555

242-2555

242-2540

242-2540

242-2541

242-2555

242-2555

241-0895

238-6882

242-2554

241-7576

241-7576

Cylinder length is from open end to centerline of trunnion.

34.03

40.30

50.15

59.29

50.15

59.29

50.15

50.15

24.30

24.30

24.30

24.30

24.30

16.90

40.30

34.03

40.30

59.29

engt h

re Stan Diamdard Cy linde . (In. r Bo )

6.50

Rod No. Assemb lyPa rt

4J-7617

3J-4907

7J-2206

7J-2206

7J-2206

7J-2206

7J-2206

3R-4137

2R-0739

7J-9715

7J-9715

5R-0058

3R-4101

3R-4101

3J-6654

3R-4104

117-0113

117-0113

Rod No. Assemb lyPa rt

144-7343

9T-4008

6E-1455

4T-0498

168-4846

100-4532

112-4055

110-6899

105-3667

3G-5764

112-4055

110-6899

105-3667

3G-5764

113-4391

6E-3914

6E-3914

6E-4859

6E-4859

6E-4859

Rod No. Assemb lyPa rt

9T-5780

9T-5780

9T-5780

6E-5914

9T-7214

9T-7214

9T-9316

9T-7214

9T-7214

6E-5977

6E-5974

6E-5983

6E-5983

6E-5904

6E-5904

9T-5749

9T-5749

6E-5897

8J-5389

7J-5879

7J-5879

an R od P

art N o. Rem

0R-3087

0R-3087

0R-3087

0R-1299

0R-1299

Ro d D iame ter (I n.

2.50

2.50

2.50

2.25

1.50

1.50

1.50

1.50

1.50

1.50

1.50

1.75

1.75

1.75

1.75

2.25

2.25

2.25

1.50

1.75

1.75

Rod L

(In.)

243-0398

186-4382

243-0398

234-2591

233-9204

185-6596

233-9204

233-9204

185-6596

233-9204

233-9204

234-2595

240-2482

234-2595

240-2482

235-0355

246-5914

240-2016

240-2016

240-1671

Cylinder length is from open end to centerline of trunnion.

30.37

30.37

30.37

33.05

18.70

18.70

18.70

18.70

18.70

18.96

18.96

18.94

18.94

18.94

18.94

35.81

35.81

36.21

18.25

39.09

39.09

engt h

re Stan Diamdard Cy linde . (In. r Bo )

3.25

Rod No. Assemb lyPa rt

6J-2801

6J-2801

9T-4067

9T-4067

134-1401

9T-4067

9T-4067

9T-2642

9T-2642

9T-1809

134-2669

4T-2670

4T-2670

1U-3326

3G-6561

3G-6561

3G-6561

8J-5389

6E-5914

111-6249

108-9329

111-6248

an R od P

art N o. Rem

10R-0125

10R-0125

10R-0125

10R-0125

0R-2700

0R-2700

0R-2713

0R-2495

0R-2495

0R-2495

Ro d D iame ter (I n.

1.97

1.97

2.50

2.50

2.50

2.50

2.50

1.50

1.50

2.25

2.25

2.50

2.50

1.50

2.25

2.25

2.25

1.50

2.25

1.75

1.50

2.25

2.25

Rod L

(In.)

240-6899

240-6899

186-4362

243-5798

186-4362

231-0898

186-4362

233-9204

185-6596

241-8921

186-4378

186-4350

246-5913

241-7579

241-0898

241-0898

246-5914

234-2591

235-0353

234-2592

235-0355

235-0355

186-4395

186-4395

231-0900

186-4395

186-4377

186-4377

Cylinder length is from open end to centerline of trunnion.

20.88

20.88

29.70

29.70

30.13

29.70

29.70

23.24

23.24

37.34

37.66

33.72

33.72

22.83

38.29

38.29

38.29

18.25

33.05

39.45

22.26

39.20

36.21

engt h

re Stan Diamdard Cy linde . (In. r Bo )

3.50

Rod No. Assemb lyPa rt

4J-4686

2K-7366

2K-6827

8J-5701

8J-5661

1K-9037

1K-9037

4J-4672

4J-4672

4J-4686

4J-4686

2K-7366

2K-6827

8J-5701

7J-9683

7J-9683

6J-7815

6J-7815

3G-5474

3G-5474

3G-5474

3G-5474

an R od P

art N o. Rem

0R-1534

0R-1534

0R-0897

Ro d D iame ter (I n.

2.00

2.00

2.00

2.00

2.00

2.00

2.00

2.00

2.00

2.00

2.00

2.00

2.00

2.00

2.00

2.00

2.00

2.00

2.00

2.00

2.00

2.00

1.50

Rod L

(In.)

240-6899

240-6899

240-6899

240-6899

233-9205

240-6899

233-9205

240-6899

246-5922

233-9207

233-9207

246-5924

Cylinder length is from open end to centerline of trunnion.

27.14

19.13

32.31

32.31

23.38

20.50

20.50

45.47

45.47

27.14

27.14

19.13

32.31

32.31

27.00

27.00

27.00

27.00

24.44

24.44

24.44

24.44

23.61

engt h

re Stan Diamdard Cy linde . (In. r Bo )

3.00

Rod No. Assemb lyPa rt

119-1063

9T-6733

134-1396

9T-6672

9T-6672

9T-6739

9T-6739

134-1399

4T-2667

3G-3313

3G-2983

3G-2983

3G-2983

4T-9384

4T-9384

4T-2667

3G-3313

3G-2983

3G-2983

3G-2983

4T-9384

4T-9384

an R od P

art N o. Rem

0R-7345

10R-0132

0R-2699

0R-2494

0R-2493

0R-2493

0R-2493

0R-2699

0R-2494

0R-2493

0R-2493

0R-2493

Ro d D iame ter (I n.

2.50

2.50

2.50

1.50

1.50

2.50

2.50

2.50

2.50

1.50

2.50

2.50

2.50

2.00

2.00

2.50

1.50

2.50

2.50

2.50

2.00

2.00

Rod L

(In.)

180-9872

186-4382

186-4382

233-9204

185-6596

231-0898

186-4362

186-4362

243-0383

246-5913

186-4378

186-4350

233-9205

240-6899

243-0383

246-5913

186-4378

186-4350

233-9205

240-6899

231-0900

186-4395

186-4395

243-0396

246-5921

186-4377

186-4377

233-9207

243-0396

246-5921

186-4377

186-4377

233-9207

Cylinder length is from open end to centerline of trunnion.

37.92

32.73

33.15

25.09

25.09

37.91

37.91

38.34

36.08

25.13

39.04

39.04

39.04

18.51

18.51

36.08

25.13

39.04

39.04

39.04

18.51

18.51

engt h

re Stan Diamdard Cy linde . (In. r Bo )

4.00

Rod No. Assemb lyPa rt

7J-9863

7J-9863

7J-9863

7J-9863

7J-9722

7J-9722

7J-9722

7J-9722

6J-5689

6J-5689

7J-9843

6J-5739

8J-5681

8J-5681

an R od P

art N o. Rem

0R-1354

0R-1354

0R-1354

0R-1354

0R-1307

0R-1307

0R-1307

0R-1307

0R-0897

Ro d D iame ter (I n.

2.25

2.25

2.25

2.25

2.00

2.00

2.00

2.00

2.00

2.00

1.50

1.50

2.00

2.00

Rod L

(In.)

241-8919

241-0896

241-8919

241-0896

240-9938

238-4501

240-9938

238-4501

246-5922

246-5924

Cylinder length is from open end to centerline of trunnion.

44.87

44.87

44.87

44.87

26.28

26.28

26.28

26.28

26.28

26.28

23.61

23.61

25.84

25.84

engt h

re Stan Diamdard Cy linde . (In. r Bo )

5.00

Rod No. Assemb lyPa rt

3G-5282

3G-5282

3G-5106

3G-5106

9T-1193

9T-1193

9T-1193

3G-5277

3G-5277

3G-5277

3G-5282

3G-5282

3G-5282

3G-5106

3G-5106

9T-1193

9T-1193

9T-1193

3G-5277

3G-5277

3G-5277

an R od P

art N o. Rem

0R-1407

0R-1407

0R-1433

0R-1433

0R-1433

0R-1186

0R-1186

0R-1186

0R-1407

0R-1407

0R-1407

0R-1433

0R-1433

0R-1433

0R-1186

0R-1186

0R-1186

Ro d D iame ter (I n.

2.75

2.75

1.75

1.75

2.50

2.50

2.50

2.50

2.50

2.50

2.75

2.75

2.75

1.75

1.75

2.50

2.50

2.50

2.50

2.50

2.50

Rod L

(In.)

243-5816

240-1881

240-1661

240-1661

228-5273

228-5273

243-5812

243-5816

240-1881

240-1661

240-1661

228-5273

228-5273

Cylinder length is from open end to centerline of trunnion.

37.91

37.91

24.78

24.78

41.63

41.63

41.63

41.48

41.48

41.48

37.91

37.91

37.91

24.78

24.78

41.63

41.63

41.63

41.48

41.48

41.48

engt h

re Stan Diamdard Cy linde . (In. r Bo )

5.50

Rod No. Assemb lyPa rt

9J-7871

4J-4615

8J-5688

8J-5681

8J-5681

4J-4927

4J-4927

9J-7871

4J-4615

2K-6827

4J-4924

9J-8740

4J-4613

9J-8740

4J-4613

8J-5701

8J-5688

3G-5282

137-7854

139-3314

105-0106

an R od P

art N o. Rem

0R-1407

10R-0128

Ro d D iame ter (I n.

2.50

2.49

2.00

2.00

2.00

2.00

2.00

2.50

2.49

2.00

2.00

2.50

2.49

2.50

2.49

2.00

2.00

2.75

2.75

1.75

1.75

Rod L

(In.)

228-0809

228-0809

228-0809

227-5350

227-5350

Cylinder length is from open end to centerline of trunnion.

28.68

28.68

22.13

25.84

25.84

28.06

28.06

28.68

28.68

32.31

28.06

47.56

47.57

47.56

47.57

32.31

22.13

37.91

38.31

23.89

23.67

engt h

re Stan Diamdard Cy linde . (In. r Bo )

3.00

Rod No. Assemb lyPa rt

4J-4769

8J-5724

8J-5724

8J-5694

8J-5688

8J-5681

8J-5681

8J-3849

6J-4502

6J-4502

5J-1570

5J-1310

5J-1310

4J-4927

4J-4927

2K-6827

7J-9692

7J-9692

7J-9692

an R od P

art N o. Rem

0R-1275

0R-1275

0R-1275

Ro d D iame ter (I n.

2.49

2.00

2.00

2.00

2.00

2.00

2.00

3.00

2.00

2.00

2.50

2.50

2.50

2.00

2.00

2.00

2.50

2.50

2.50

Rod L

(In.)

238-4487

243-0381

243-0381

242-2560

Cylinder length is from open end to centerline of trunnion.

31.64

29.50

29.50

34.42

22.13

25.84

25.84

42.27

25.50

25.50

47.58

27.16

27.16

28.06

28.06

32.31

47.58

47.58

47.58

engt h

re Stan Diamdard Cy linde . (In. r Bo )

5.50

Rod No. Assemb lyPa rt

9T-1807

9T-1807

9T-1807

3G-0894

1U-1146

1U-1146

1U-1146

1U-1146

6E-2191

6E-4896

9T-1807

9T-1807

9T-1807

3G-0894

3G-0720

3G-0720

3G-0720

3G-0720

1U-1146

1U-1146

1U-1146

1U-1146

an R od P

art N o. Rem

10R-0146

10R-0146

10R-0146

0R-3444

0R-7347

10R-0146

10R-0146

10R-0146

0R-1412

0R-1412

0R-1412

0R-1412

0R-3444

Ro d D iame ter (I n.

1.75

1.75

1.75

1.75

3.00

3.00

3.00

3.00

3.25

1.65

1.75

1.75

1.75

1.75

2.50

2.50

2.50

2.50

3.00

3.00

3.00

3.00

3.25

Rod L

(In.)

240-1881

240-1881

240-1661

240-1661

244-2062

244-2062

244-2062

244-2062

245-0585

240-1881

240-1881

240-1881

240-1661

240-1661

186-4378

186-4378

186-4350

244-2062

244-2062

244-2062

244-2062

245-0585

244-2063

244-2063

244-2063

244-2063

245-0587

186-4377

244-2063

244-2063

244-2063

244-2063

245-0587

Cylinder length is from open end to centerline of trunnion.

27.47

27.47

27.47

27.47

47.97

47.97

47.97

47.97

38.64

27.54

27.47

27.47

27.47

27.47

40.61

40.61

40.61

40.61

47.97

47.97

47.97

47.97

38.64

engt h

re Stan Diamdard Cy linde . (In. r Bo )

7.00

Rod No. Assemb lyPa rt

4J-4556

8J-5731

8J-5701

4J-4926

185-7362

163-1743

129-4449

118-9003

163-0327

119-5957

224-5700

129-4449

125-0025

125-0025

163-0327

125-0025

125-0025

6E-2191

6E-4896

9T-1807

9T-1807

an R od P

art N o. Rem

10R-0620

0R-7380

10R-0620

10R-0030

10R-0030

0R-7380

10R-0030

10R-0030

0R-3444

0R-7347

10R-0146

10R-0146

Ro d D iame ter (I n.

2.49

2.25

2.00

2.00

3.25

3.25

1.75

1.75

3.25

3.00

3.00

1.75

3.00

3.00

3.25

1.65

1.75

1.75

Rod L

(In.)

244-2077

228-1779

228-1779

228-1792

228-1795

240-1881

209-3498

202-7897

228-1793

228-1793

245-0585

240-1881

240-1881

240-1881

228-1794

228-1794

245-0587

Cylinder length is from open end to centerline of trunnion.

50.16

25.72

32.31

35.98

46.36

40.49

28.19

27.93

46.36

49.90

49.90

28.19

49.90

49.90

38.64

27.54

27.47

27.47

engt h

re Stan Diamdard Cy linde . (In. r Bo )

3.50

Rod No. Assemb lyPa rt

7J-2468

6J-4523

5J-2462

5J-2462

5J-2462

4J-4927

4J-4927

4J-8943

4J-8070

4J-4780

4J-4780

2K-6827

7J-9367

4J-8273

4J-8273

8J-5731

8J-5701

4J-4926

7J-9359

an R od P

art N o. Rem

0R-3065

0R-3065

0R-3065

0R-1272

0R-1269

Ro d D iame ter (I n.

2.25

2.25

2.50

2.50

2.50

2.00

2.00

0.62

2.00

2.25

2.25

2.00

2.50

2.50

2.50

2.25

2.00

2.00

2.50

Rod L

(In.)

242-2549

242-2550

243-0380

243-0399

Cylinder length is from open end to centerline of trunnion.

27.12

27.12

29.04

29.04

29.04

28.06

28.06

12.73

33.44

21.50

21.50

32.31

50.16

50.16

50.16

25.72

32.31

35.98

29.08

engt h

re Stan Diamdard Cy linde . (In. r Bo )

6.00

Rod No. Assemb lyPa rt

7J-2468

6J-4523

5J-2462

5J-2462

5J-2462

4J-4927

4J-4927

4J-8070

4J-4780

4J-4780

7J-9367

7J-9367

4J-8273

4J-8273

8J-5731

4J-4926

7J-9359

7J-9359

7J-9359

7J-9359

6J-6885

6J-6885

6J-6886

an R od P

art N o. Rem

0R-3065

0R-3065

0R-3065

0R-1272

0R-1272

0R-1269

0R-1269

0R-1269

0R-1269

0R-1353

Ro d D iame ter (I n.

2.25

2.25

2.50

2.50

2.50

2.00

2.00

2.00

2.25

2.25

2.50

2.50

2.50

2.50

2.25

2.00

2.50

2.50

2.50

2.50

2.50

2.50

2.50

Rod L

(In.)

242-2549

242-2550

242-2550

242-2550

242-2550

242-2550

243-0380

243-0399

7X-2835

243-0399

7X-2835

243-0399

Cylinder length is from open end to centerline of trunnion.

27.12

27.12

29.04

29.04

29.04

28.06

28.06

33.44

21.50

21.50

50.16

50.16

50.16

50.16

25.72

35.98

29.08

29.08

29.08

29.08

29.08

29.08

30.20

engt h

re Stan Diamdard Cy linde . (In. r Bo )

6.00

Rod No. Assemb lyPa rt

9T-6275

9T-6275

9T-8994

9J-7110

9J-7084

8F-2658

7J-9359

7J-9359

7J-9359

7J-9359

6J-6885

6J-6885

6J-6886

6J-6886

6J-6886

6J-6886

6J-6886

6J-6886

6J-6886

6J-6886

Rod No. Assemb lyPa rt

7J-9359

7J-9359

7J-9359

9T-1805

9T-1805

7J-9357

7J-9367

171-6049

9T-8994

135-4690

133-4047

9T-8994

133-4047

135-4690

133-4047

133-4047

an R od P

art N o. Rem

0R-1269

0R-1269

0R-1269

0R-1182

0R-1182

0R-1182

0R-1272

0R-1264

10R-0115

0R-1264

10R-0115

10R-0115

10R-0115

Ro d D iame ter (I n.

2.50

2.50

2.50

2.00

2.00

2.00

2.50

3.22

2.00

3.25

3.22

3.25

2.00

3.25

3.25

Rod L

(In.)

242-2550

242-2550

242-2550

237-8277

237-8277

242-2549

228-1780

228-1780

216-8186

228-1778

202-7897

228-1779

228-1779

7X-2835

243-0399

7X-2835

243-0380

Cylinder length is from open end to centerline of trunnion.

29.08

29.08

29.08

33.43

33.43

33.44

50.16

37.52

32.48

50.55

37.52

50.55

32.48

50.55

50.55

engt h

re Stan Diamdard Cy linde . (In. r Bo )

7.00

Rod No. Assemb lyPa rt

7J-9733

7J-9733

7J-9733

5J-4544

7J-9780

7J-9780

7J-9780

7J-9780

7J-9780

7J-9780

5J-2634

5J-2634

9J-5639

4J-4769

8J-5770

7J-2470

6J-4696

5J-4544

7J-9815

7J-9815

7J-2137

7J-2137

Rod No. Assemb lyPa rt

9T-2420

9T-2420

9T-2420

4T-7887

4T-7887

3G-4423

3G-4423

3G-4423

6E-3478

9J-4916

9J-4916

9J-4916

9J-4916

9T-1762

9T-1762

9J-5874

9T-1762

9T-1762

9J-5874

6E-6657

1U-3522

1U-3522

an R od P

art N o. Rem

0R-1540

0R-1540

0R-1540

0R-9244

0R-9244

0R-9244

0R-1180

0R-1180

0R-1180

0R-1180

0R-3084

0R-3084

0R-3084

0R-3084

0R-9247

0R-1175

0R-1175

Ro d D iame ter (I n.

3.00

3.00

3.00

3.00

3.00

2.75

2.75

2.75

2.75

2.75

2.75

2.75

2.75

2.25

2.25

2.25

2.25

2.25

2.25

2.25

3.50

3.50

Rod L

(In.)

244-2060

228-0807

244-2060

244-2060

244-2060

243-5815

243-5815

243-5815

243-5815

243-5815

228-0808

228-0808

241-8917

241-0896

241-0896

241-8917

241-0896

241-0896

241-7585

245-6831

245-6831

228-0810

228-0810

228-0810

241-8918

241-8918

Cylinder length is from open end to centerline of trunnion.

52.57

52.57

52.57

52.57

52.57

37.07

37.07

37.07

31.03

38.95

38.95

38.95

38.95

35.12

35.12

35.24

35.12

35.12

35.24

32.41

53.27

53.27

engt h

re Stan Diamdard Cy linde . (In. r Bo )

7.50

Rod No. Assemb lyPa rt

189-3041

112-5005

189-3041

112-5005

146-3034

146-3034

9T-2420

9T-2420

124-0615

124-0615

189-3041

189-3041

112-5005

115-1372

146-3034

146-3034

189-3041

189-3041

111-8187

111-8187

111-8187

an R od P

art N o. Rem

0R-9236

0R-9236

0R-9236

0R-9236

0R-1540

0R-1540

0R-9238

0R-9238

0R-9236

0R-9236

0R-9236

0R-9234

0R-9236

0R-9236

0R-9232

0R-9232

0R-9232

0R-1540

Ro d D iame ter (I n.

2.75

2.75

2.75

2.75

3.00

3.00

3.00

3.00

3.00

3.00

2.75

2.75

2.75

2.25

3.00

3.00

2.75

2.75

3.50

3.50

3.50

3.00

Rod L

(In.)

228-0808

228-0808

228-0808

228-0808

228-0806

228-0806

228-0807

228-0807

228-0806

228-0806

228-0808

228-0808

228-0808

241-8921

228-0806

228-0806

216-8186

228-1775

228-0807

228-0810

228-0810

228-0810

Cylinder length is from open end to centerline of trunnion.

43.43

43.43

43.43

43.43

43.71

43.71

52.57

52.57

41.52

41.52

43.43

43.43

43.43

36.92

43.71

43.71

43.43

43.43

54.41

54.41

54.41

52.57

engt h

re Stan Diamdard Cy linde . (In. r Bo )

6.25

Rod No. Assemb lyPa rt

4T-7574

4T-7574

3G-2971

9J-8171

9J-8171

9J-8171

9J-8171

053-8399

053-8401

3G-3975

3G-3975

8J-5781

3G-3975

1U-2553

7J-9757

7J-9757

7J-3226

6J-5759

5J-2073

4J-8030

7J-9715

7J-9715

an R od P

art N o. Rem

0R-1174

0R-1174

0R-9218

0R-3079

0R-3079

0R-3079

0R-3079

0R-1257

0R-1257

0R-1257

0R-1309

0R-1309

0R-9220

0R-9220

Ro d D iame ter (I n.

3.50

3.50

3.50

2.25

2.25

2.25

2.25

4.00

4.00

4.00

4.00

4.00

2.75

2.75

2.75

2.75

2.75

2.50

2.25

2.25

Rod L

(In.)

228-1775

193-3116

245-6832

241-7578

241-0895

241-7578

241-0895

246-0659

246-3427

246-3427

246-0659

235-5802

235-5802

243-0382

243-0382

241-0895

241-0895

241-7577

241-7576

241-7577

241-7576

246-0660

246-0660

246-0660

246-0660

241-7576

241-7576

Cylinder length is from open end to centerline of trunnion.

62.57

62.57

40.75

39.81

39.81

39.81

39.81

65.72

65.72

61.90

65.72

59.15

51.14

51.14

46.95

46.95

46.95

51.14

40.30

40.30

engt h

re Stan Diamdard Cy linde . (In. r Bo )

5.00

Rod No. Assemb lyPa rt

6J-9373

7J-9795

7J-9795

7J-9795

7J-2674

5J-6466

7J-9813

8J-0183

7J-1233

7J-1233

7J-9789

7J-9789

7J-9789

7J-9789

7J-9789

8J-0183

7J-1233

8J-0183

7J-1233

7J-1233

7J-1233

6E-1171

145-9901

an R od P

art N o. Rem

0R-9215

0R-9215

0R-9215

0R-1535

0R-9213

0R-1536

0R-1536

0R-1536

0R-1536

0R-1536

0R-9213

0R-9213

0R-9993

0R-8899

Ro d D iame ter (I n.

3.50

2.50

2.50

2.50

2.50

2.50

3.50

6.50

6.50

6.50

6.50

6.50

6.50

6.50

6.50

6.50

6.50

6.50

6.50

6.50

6.50

5.75

5.75

Rod L

(In.)

242-2539

243-0381

189-1782

189-1781

229-7176

229-7176

Cylinder length is from open end to centerline of trunnion.

67.15

44.91

44.91

44.91

42.65

42.65

67.34

72.47

72.47

72.47

72.47

72.47

72.47

72.47

72.47

72.47

72.47

72.47

72.47

72.47

72.47

54.29

54.29

engt h

re Stan Diamdard Cy linde . (In. r Bo )

11.50

Rod No. Assemb lyPa rt

1U-1763

102-6246

102-6246

9J-5426

9J-2985

9J-2985

1U-1774

102-8730

107-5547

9J-3367

107-5547

9J-3367

106-9459

1U-1763

106-9459

1U-1763

9J-5426

an R od P

art N o. Rem

0R-1431

0R-8900

0R-8900

0R-3078

0R-0998

0R-0998

0R-1436

10R-0200

0R-4906

0R-4906

0R-4476

0R-1431

0R-4476

0R-1431

0R-3078

Ro d D iame ter (I n.

4.00

4.00

4.00

3.25

7.00

7.00

7.00

7.00

4.00

4.00

4.00

4.00

4.00

4.00

4.00

4.00

3.25

Rod L

(In.)

246-0644

246-0644

246-0644

245-0581

246-5907

246-5907

246-5907

246-5907

246-0644

246-0644

246-0644

246-0644

246-0644

246-0644

246-0644

246-0644

245-0581

246-0650

246-0650

246-0650

245-0583

246-5908

246-5908

246-5908

246-5908

246-0650

246-0650

246-0650

246-0650

246-0650

246-0650

246-0650

246-0650

245-0583

Cylinder length is from open end to centerline of trunnion.

64.85

62.04

62.04

51.43

74.50

74.50

78.48

77.31

57.84

49.53

57.84

49.53

73.16

64.85

73.16

64.85

51.43

engt h

re Stan Diamdard Cy linde . (In. r Bo )

7.00

Rod No. Assemb lyPa rt

6E-0514

114-2822

114-2822

114-2822

114-2822

114-2822

114-2822

230-0973

112-3174

112-3174

112-3174

230-0973

112-3174

112-3174

112-3174

6E-0526

6E-0526

219-6274

219-6274

219-6274

219-6274

101-0331

an R od P

art N o. Rem

0R-4472

0R-4472

0R-4470

0R-4470

0R-4474

0R-4474

0R-4474

0R-4474

Ro d D iame ter (I n.

5.50

5.50

5.50

5.50

5.50

5.50

5.50

5.50

5.50

5.50

5.50

5.50

5.50

4.25

4.25

8.00

Rod L

(In.)

246-3437

246-3437

246-3437

246-3437

246-3437

246-3437

246-3437

234-2590

246-3437

246-3437

246-3437

234-2590

234-2590

246-3437

246-3437

246-3437

246-3431

246-3431

234-2590

246-3437

234-2590

246-3437

245-6821

246-3438

246-3438

246-3438

246-3438

246-3438

246-3438

246-3438

246-3438

246-3438

246-3438

246-3438

246-3438

246-3438

246-3438

246-3438

246-3438

246-3432

246-3432

245-6820

Cylinder length is from open end to centerline of trunnion.

66.57

92.93

92.93

92.93

92.93

92.93

92.93

76.00

76.00

76.00

76.00

76.00

76.00

64.92

64.92

87.40

engt h

re Stan Diamdard Cy linde . (In. r Bo )

12.50

Rod No. Assemb lyPa rt

230-0973

112-3174

112-3174

112-3174

230-0973

112-3174

112-3174

112-3174

6E-0526

6E-0526

219-6274

219-6274

219-6274

219-6274

101-0331

101-0331

6E-0284

101-0332

101-0332

6E-0038

193-4080

193-4081

an R od P

art N o. Rem

0R-4472

0R-4472

0R-4470

0R-4470

0R-4474

0R-4474

0R-4474

0R-4474

0R-4471

0R-4473

Ro d D iame ter (I n.

5.50

5.50

5.50

5.50

5.50

5.50

4.25

4.25

8.00

8.00

8.00

8.00

8.00

8.00

8.00

8.00

Rod L

(In.)

234-2590

246-3437

246-3437

246-3437

234-2590

234-2590

246-3437

246-3437

246-3437

246-3431

246-3431

234-2590

246-3437

234-2590

246-3437

245-6821

245-6821

245-6821

245-6821

245-6821

245-6821

245-6821

245-6821

246-3438

246-3438

246-3438

246-3438

246-3438

246-3438

246-3438

246-3438

246-3438

246-3432

246-3432

245-6820

245-6820

245-6820

245-6820

245-6820

245-6820

Cylinder length is from open end to centerline of trunnion.

76.00

76.00

76.00

76.00

76.00

76.00

64.92

64.92

87.40

87.40

87.40

83.07

83.07

83.07

83.07

87.40

engt h

re Stan Diamdard Cy linde . (In. r Bo )

12.50

Rod No. Assemb lyPa rt

4T-2670

4T-2670

1U-3326

3G-6561

3G-6561

3G-6561

7J-5879

7J-5879

8J-0117

7J-5890

7J-5890

7J-5890

7J-5890

230-1288

115-8181

115-8181

115-8181

101-9570

6E-0519

230-1288

an R od P

art N o. Rem

0R-2700

0R-2700

0R-2713

0R-2495

0R-2495

0R-2495

0R-1299

0R-1299

0R-2712

0R-9210

0R-9210

Ro d D iame ter (I n.

2.50

2.50

1.50

2.25

2.25

2.25

1.75

1.75

1.50

2.00

2.00

2.00

2.00

5.50

5.50

5.50

5.50

5.50

Rod L

(In.)

186-4378

186-4350

246-5913

241-7579

241-0898

241-0898

240-2016

240-2016

240-1671

246-5909

233-9205

240-6899

240-6899

233-9205

240-6899

240-6899

246-3437

186-4377

186-4377

246-5920

233-9207

233-9207

246-3438

Cylinder length is from open end to centerline of trunnion.

33.72

33.72

22.83

38.29

38.29

38.29

39.09

39.09

19.68

33.05

33.05

33.05

33.05

91.33

91.33

91.33

83.10

83.10

engt h

re Stan Diamdard Cy linde . (In. r Bo )

10.50

Rod No. Assemb lyPa rt

134-2659

134-2659

9T-8154

9T-8154

1U-2288

1U-2288

5R-5897

7J-6248

7J-6248

5R-5897

5R-5754

5R-5753

5J-7352

7J-6249

7J-6249

7J-6248

7J-6248

5J-7352

7J-6249

7J-6249

Rod No. Assemb lyPa rt

5J-2385

3G-3888

3G-3877

3G-3877

3G-5676

3G-5676

4T-8565

3G-8824

4T-0887

4T-0887

3G-8480

6E-3571

6E-3571

5J-2385

8J-9451

6E-3571

3G-7276

5J-2385

3G-7276

3G-3888

3G-3877

Rod No. Assemb lyPa rt

5J-7945

5J-7945

5J-8957

5J-2385

4C-2162

1U-3901

8J-9451

8J-9451

8J-9451

8J-9451

5J-2385

4C-2162

8J-7375

1U-3901

8J-9451

5J-2385

4C-2162

1U-3901

1U-3901

8J-9451

8J-9451

8J-9451

Rod No. Assemb lyPa rt

8J-7375

5J-7945

5J-8957

5J-7945

5J-8957

8J-9451

8J-9451

5J-2385

5J-7945

5J-8957

5J-7945

5J-8957

8J-0198

8J-1817

8J-7375

8J-7375

5J-2893

Rod No. Assemb lyPa rt

8J-7375

5J-7945

5J-8957

5J-7945

5J-8957

8J-9451

8J-9451

8J-8467

5J-2385

5J-7945

5J-8957

5J-7945

5J-8957

8J-0198

8J-6063

4J-4888

5J-0771

Rod No. Assemb lyPa rt

4J-7418

4J-7418

4J-8697

5J-4287

4J-7565

4J-4918

4J-7405

4J-7417

4J-7417

4J-7418

4J-7418

6J-1977

3D-4742

5J-2385

8J-7375

8J-7375

5J-8957

8J-0198

5J-2893

5J-2893

5J-2893

Rod No. Assemb lyPa rt

5J-7801

5J-7801

5J-7945

5J-8957

5J-7945

5J-8957

9J-1190

9J-1190

7J-3383

7J-2385

7J-2385

4J-7417

4J-7417

4J-7418

4J-7418

5J-7801

5J-7801

Rod No. Assemb lyPa rt

4J-7417

4J-7418

4J-7418

4J-7417

4J-7417

4J-7418

4J-7418

4J-7417

4J-7417

4J-7417

4J-7417

4J-7418

4J-8697

5J-9060

5J-9060

5J-4292

5J-4287

4J-7565

5J-7801

5J-7801

1U-3901

Rod No. Assemb lyPa rt

9J-1190

9J-1190

7J-3383

5J-7650

5J-7650

5J-7650

5J-7801

5J-7801

5J-7801

5J-7801

5J-7801

5J-7650

5J-7650

5J-7650

5J-7801

5J-7801

3J-9032

3J-9032

3J-9032

3J-9032

Rod No. Assemb lyPa rt

5J-7801

5J-7801

7J-6297

7J-2168

5J-8957

9J-1190

9J-1190

7J-3383

5J-7650

5J-7650

5J-7650

5J-7650

141-3254

131-4127

1U-3901

5J-7945

8J-9924

5J-8957

Cylinder length is from open end to centerline of eye.

0R-1793

0R-1793

10R-0041

6.50

6.50

6.00

7.25

7.25

3.00

7.25

7.25

7.25

7.25

6.50

Rod No. Assemb lyPa rt

9J-0508

9J-0508

4T-5636

5J-7945

8J-9924

5J-8957

5J-7945

5J-8957

9J-0508

9J-0508

9J-0508

8J-8467

5J-7801

5J-7801

5J-7945

5J-8957

5J-7945

Cylinder length is from open end to centerline of eye.

0R-8293

0R-8293

0R-8293

0R-8293

0R-8293

0R-1793

0R-1793

Rod No. Assemb lyPa rt

5J-8957

9J-0508

9J-0508

9J-0508

5J-7801

5J-7801

8J-9924

8J-9924

5J-8957

9J-1190

9J-1190

7J-3383

9J-0407

9J-0407

9J-0407

9J-0407

9J-0407

9J-0407

7J-2385

Rod No. Assemb lyPa rt

5J-8033

5J-8033

6J-1977

4J-8431

5J-8116

5J-4353

5J-8148

5J-8148

5J-7945

5J-8957

5J-7945

5J-8957

7J-6144

5J-8614

7J-6144

5J-8614

4J-7405

5J-8033

Rod No. Assemb lyPa rt

5J-8614

4J-7422

4J-7422

4J-7423

4J-7423

5J-9452

5J-9452

5J-8116

4J-7847

4J-7422

4J-7422

4J-7423

4J-7423

4J-7423

4J-7423

6J-6464

6J-6464

6J-6464

6J-6464

6J-2008

4J-8646

5J-1534

Rod No. Assemb lyPa rt

5J-9452

6J-2008

4T-0887

4T-0887

4J-8646

5J-1534

5J-8116

5J-4353

3G-8480

4T-8565

5J-8148

3G-5462

1U-3901

1U-3901

1U-3901

3G-8755

5J-8148

5J-8148

5J-7945

5J-8957

Cylinder length is from open end to centerline of eye.

0R-1379

0R-1379

10R-0111

10R-0111

10R-0111

10R-1328

0R-3130

10R-1328

10R-1329

0R-3130

Rod No. Assemb lyPa rt

5J-8614

7J-6144

5J-8614

5J-9452

5J-9452

8J-8467

8J-6063

4J-4888

5J-8116

5J-8148

5J-8148

5J-7945

5J-8957

5J-7945

4T-4277

5J-8521

3J-9783

5J-8957

7J-6144

5J-8614

5J-9452

5J-9452

8J-6063

Rod No. Assemb lyPa rt

7J-6144

5J-8614

7J-6144

5J-8614

4J-7847

3G-8824

5J-9452

5J-9452

5J-9452

5J-9452

6J-2008

4T-0887

4T-0887

4J-8646

5J-1534

8J-8467

8J-6063

4J-4888

5J-8116

5J-4353

3G-8480

4T-8565

Rod No. Assemb lyPa rt

4J-7422

4J-7423

4J-7423

6J-6464

4J-8644

5J-8532

3J-7775

3J-6704

3J-6704

6J-6464

6J-6464

6J-6464

6J-6464

6J-3039

5J-1533

5J-4350

4J-7846

4D-6749

4D-6772

4J-2068

Rod No. Assemb lyPa rt

1J-1797

2K-7366

2K-6827

4J-4629

4J-4832

9J-8174

5J-7352

5J-7352

8J-5701

4J-9904

4J-9904

4J-4629

4J-4629

4J-4629

5J-7352

4J-9904

4J-9904

3H-9534

3H-9534

3H-9534

4J-8644

Rod No. Assemb ly