SAP2000-Example 3D RC Building

Analysis and Design of 3D RC Building Using SAP2000

ACECOMS, AIT

SAP2000 Tutorial Example

Analysis and Design of 3D RC Building Using SAP2000 Table of Content Objective................................................................................................................................................3 Problem .................................................................................................................................................3

Modeling, Dynamic Analysis of RC Building .....................6 Step-by-Step Solution .........................................................................................................................6 1.

Start Model from Template................................................................................ 6

2.

Define Material Properties................................................................................. 8

3.

Define Frame Sections....................................................................................... 9

4.

Define Slab Sections........................................................................................ 12

5.

Define Load Cases ........................................................................................... 13

6.

Modify Frame .................................................................................................. 14

7.

Copy Floor 1 to Floor 2-5 ................................................................................ 18

8.

Assign Slab Loads ........................................................................................... 19

9.

Assign Beam Loads ......................................................................................... 20

10.

Assign Dynamic Loads................................................................................ 21

11.

Start Analysis............................................................................................... 21

Analysis and Design of 3D RC Building

2/ 21

ACECOMS, AIT

SAP2000 Tutorial Example

Objective To demonstrate and practice step-by-step on the modeling, dynamic analysis and design of 5 story reinforced concrete building.

Problem Part A: Carry out the modeling, dynamic analysis and design of 5 story reinforced concrete building subjected to static loads (UBC94 response spectrum load in Y direction). Material Properties Strength of concrete (Fc’) Yield strength of main reinforcement (Fy) Yield strength of shear reinforcement (Fys) Young Modulus of concrete ( Ec)

= 4 ksi = 60 ksi = 60 ksi = 3600 ksi

Loading Load Cases

Type

Details

DEAD

Dead load

Use Self Weight Multiplier

SUPERDL

Dead load

Slabs: 35 psf Beams: 250 plf

LIVE

Live load

Slab: 100 psf

SPEC1 (for Part B)

Dynamic load

UBC94 response spectrum in Y direction

Slab Section Reinforced concrete solid slab, thickness = 6 inch

Frame Sections

20"

20"

C olum n (C 1)

Analysis and Design of 3D RC Building

24"

12"

B eam (B 1)

3/ 21

ACECOMS, AIT

SAP2000 Tutorial Example

3D View of the building

Plan and Elevation View Plan View at Roof Foor A

B

C

20'

20'

C1

20'

C1

1

C1

D

B1

B1

B1

B1

C1

C1

C1

C1

2

20'

B1

B1

B1

B1

B1

B1

B1

C1

C1

C1

C1

3

20'

B1

B1

B1

B1

B1

B1

B1

C1

C1

C1

4

20'

B1

Analysis and Design of 3D RC Building

4/ 21

ACECOMS, AIT

SAP2000 Tutorial Example

Elevation At Grid Lines 2, 3, 4, A, B and C

12'

Story 5

20'

20'

20'

B1

B1

B1

C1

C1

Story 4

C1

12'

B1 C1

C1

Story 3

12'

C1

C1

12'

C1

12'

B1

C1

C1

B1

C1

B1

C1

B1 C1

C1

B1

B1

Story 1

B1

C1

B1

Story 2

C1

B1

C1

B1

C1

B1

C1

C1

Base

Elevation at Grid Line 1 and D

12'

Story 5

20'

20'

B1

B1

C1

Story 4

C1

12'

B1 C1

Story 3

C1

12'

B1 C1

Story 2

C1

12'

C1

12'

C1 B1

C1 B1

C1

C1 B1

B1

Story 1

C1 B1

C1 B1

C1

C1

Base

Analysis and Design of 3D RC Building

5/ 21

ACECOMS, AIT

SAP2000 Tutorial Example

Modeling, Dynamic Analysis of RC Building Step-by-Step Solution 1. Start Model from Template Only one floor frame will be created by template and will be copied to the remaining floors after started floor has been modified already.

Step 1-1: Start SAP2000 by clicking on the appropriate desktop shortcut or by selecting sAP2000 from your Windows Start menu. Select “Kip-in” from drop-down menu box in bottom-right screen. Go to File > New Model from Template and select space frame template as shown in above figure.

Step 1-2: Specify parameter as shown in above figure and click “OK”.

Analysis and Design of 3D RC Building

6/ 21

SAP2000 Tutorial Example

ACECOMS, AIT

Step 1-3: After clicking OK, SAP2000 creates space frame based on the parameters specified in the previous step and displays in “Plan View” and “3-D View” window.

Step 1-4: Save the project by clicking on or File > Save from main menu, enter File name = "SAP2000_ex06" and click Save.

Analysis and Design of 3D RC Building

7/ 21

ACECOMS, AIT

SAP2000 Tutorial Example

2. Define Material Properties Default concrete material (“CONC”) has been used for this example.

Step 2-1: Go to Define > Material Properties in main menu. Select CONC and click on Modify/Show Material to view/revise the material properties.

Step 2-2: Accept the default properties by clicking Cancel or OK 2 times

Analysis and Design of 3D RC Building

8/ 21

ACECOMS, AIT

SAP2000 Tutorial Example

3. Define Frame Sections 2 concrete frame sections (“B1” for rectangular beams and “C1” for circle columns) need to be defined for this example. Check the dimensions at Problem Statement part at the beginning of the example.

Step 3-1: Go to Define > Frame Sections in main menu to start frame section definition properties editor. Select “Add Rectangular” from second drop-down menu to add rectangular beam.

Step 3-2: Enter “B1” as Section Name as shown in the above figure and accept the other data. Click on Reinforcement to specify reinforcement data.

Analysis and Design of 3D RC Building

9/ 21

SAP2000 Tutorial Example

ACECOMS, AIT

Step 3-3: Select Design Type = “Beam” and click OK 2 times to go back to “Define Frame Properties” window.

Step 3-4: The “Define Frame Sections” window shows “B1” section added in the list. Select “Add Circle” from second drop-down menu to add column section.

Analysis and Design of 3D RC Building

10/ 21

SAP2000 Tutorial Example

ACECOMS, AIT

Step 3-5: Enter “C1” section properties as shown in above figure, accept other data and click on Reinforcement button to specify reinforcement data.

Step 3-6: In Design Type area select Design Type = “Column”. Clicking OK 2 times to finish this step.

Step 3-7: Define Frame Properties dialogue shows “C1” section in list. Click OK to go back to main screen, which completes the Frame Section Definition steps.

Analysis and Design of 3D RC Building

11/ 21

ACECOMS, AIT

SAP2000 Tutorial Example

4. Define Slab Sections

Step 4-1: Go to Define > Shell Sections menu command. Click on “Add New Section” and enter Section Name and Thickness. Click on “OK”.

Step 4-2: The “Define Shell Sections” window shows “SLAB1” section added in the list. Click on “OK” to end this step.

Analysis and Design of 3D RC Building

12/ 21

ACECOMS, AIT

SAP2000 Tutorial Example

5. Define Load Cases

Step 5-1: Go to Define > Static Load Cases. 1 load case named “LOAD1” has been defined as default. Enter Load = “DL” and click “Change Load” to change load case name.

Step 5-2: Define “LL” load case by entering parameter as shown in above figure and clicking “Add New Load”.

Step 5-3: Enter parameter as shown in above figure to add “SUPERDL” load case and click “Add New Load”. Click “OK” to end this step.

Analysis and Design of 3D RC Building

13/ 21

ACECOMS, AIT

SAP2000 Tutorial Example

6. Modify Frame

Step 6-1 Delete 2 Beams and 1 Column at Corner: Close “X-Y” View window by clicking on at the top-right of this window. Click on 2 beams and 1 column at the corner as shown in above figure (selection status will display “3 Frames selected” and click on “Delete” at the keyboard.

Step 6-2 Add Shell Sections: Change view to “X-Y” view by clicking on and click on slab area one by one.

Analysis and Design of 3D RC Building

. Select

14/ 21

SAP2000 Tutorial Example

ACECOMS, AIT

Step 6-3 Assign Shell Section Property: Click on and draw selection rectangular to cover all model (selection status = “15 Joints, 22 Frames, 8 Shells selected”), and select “SLAB1” and click “OK”. “SLAB1” property will be assigned in click on every slab panel. Click on to return to normal display mode.

Step 6-4 Assign “B1” Frame Section Property: Click on tion. Click on , select “B1” and click on “OK”.

Analysis and Design of 3D RC Building

to get previous selec-

15/ 21

SAP2000 Tutorial Example

ACECOMS, AIT

Step 6-5 Select all Columns: Change view to “3-D” view by clicking on . In “3-D” View shows all columns are “FSEC1” section property as default from template. Go to Select > Select > Frame Sections, select “FSEC1” and click “Ok”.

Step 6-6 Assign “C1” Section Property: Click on “OK”.

Analysis and Design of 3D RC Building

, select “B1” and click on

16/ 21

SAP2000 Tutorial Example

ACECOMS, AIT

Step 6-7 Mesh Slab Areas: Click on to select all members in model and go to Edit > Mesh Shells. Enter Mesh into “4” by “4” Shells and click “OK”.

Step 6-8 Divide Frame Elements: Click on to select all members in model and go to Edit > Divide Frames. Select “Break at intersections with selected Frames and Joints” and click “OK”.

Analysis and Design of 3D RC Building

17/ 21

ACECOMS, AIT

SAP2000 Tutorial Example

7. Copy Floor 1 to Floor 2-5

Step 7-1: Click on to select all members in model and go to Edit > Replicate. Enter Z = “144”, Number = “4” and click “OK”.

Step 7-2: Click on

to remove all section labels

Analysis and Design of 3D RC Building

18/ 21

ACECOMS, AIT

SAP2000 Tutorial Example

8. Assign Slab Loads

Step 8-1 Select All Slab Panels: Change working unit to “lb-ft”.

Step 8-2 Assign “LL” load for Slabs: click on to select all members. Click on , enter parameter as shown above figure and click “OK”. (load value will be positive for downward in “Gravity” direction.

Step 8-3 Assign “LL” load for Slabs: click on to select all members. Click on , enter parameter as shown above figure and click “OK”. (load value will be positive for downward in “Gravity” direction.

Analysis and Design of 3D RC Building

19/ 21

ACECOMS, AIT

SAP2000 Tutorial Example

9. Assign Beam Loads

Step 9-1 Select All Beams: Go to Select > Select > Frame Sections, select “B1” and click “OK”.

Step 9-2 Assign Uniform Beam Loads: Click on above figure and click “OK”.

Analysis and Design of 3D RC Building

, enter parameter as shown in

20/ 21

ACECOMS, AIT

SAP2000 Tutorial Example

10.

Assign Dynamic Loads

Step 10-1: Go to Define > Response Spectrum Cases and click on “Add New Spectra”. Enter parameter as shown in above figure and click “OK” 2 times.

11.

Start Analysis

Step 11-1: Start analysis by clicking “ANALYSIS COMPLETE”

and wait until analysis status report

Note: Viewing Analysis Results, Carrying Out Design, Viewing Design Results and Printing Input/ Output Procedures are same as Previous Example

Analysis and Design of 3D RC Building

21/ 21