SURFACE VEHICLE STANDARD
REV. JUL2005 ®
J516
Issued Revised
1952-01 2005-07
Superseding
J516 JAN2001
(R) Hydraulic Hose Fittings Fittings
1.
Scope
This SAE Standard provides general and dimensional specifications for the most common hose fittings used in conjunction with hydraulic hoses specified in SAE J517 and utilized in hydraulic systems on mobile and stationary equipment. The general specifications contained in Sections 1 through 15 are applicable to all hydraulic hose fittings and supplement the detailed specifications for the 100R-series fittings contained in the later sections of this document. This document shall be utilized as a procurement document only to the extent agreed upon by the manufacturer and user. Refer to SAE J517 J517 for specifications of hose and information on hose assemblies. SAE J1273 contains information on application factors affecting hose fittings, hose, and hose assemblies. THE RATED WORKING PRESSURE OF A HOSE ASSEMBLY COMPRISING SAE J516 FITTINGS AND SAE J517 HOSE SHALL NOT EXCEED THE LOWER OF THE TWO WORKING PRESSURE RATED VALUES. 1.1
Rationale
This document has been completely revised to reflect the metric system. Tables have been simplified by having only one max length per fitting/hose size combination. Also limited the number of jump sizes and drops. Added optional inch hex sizes. Added the idenification information (Paragraph 4).
SAE Technical Standards Board Rules Rules provide that: “This report is published by SAE SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright © 2005 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or tr ansmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER:
SAE WEB ADDRESS: ADDRESS:
Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email:
[email protected] http://www.sae.org
SAE J516 Revised JUL2005
The following are hose fitting types contained in this document: a. Male dryseal pipe thread hose fittings shall be as shown in Figure 1 for the the respective styles, and in Table 2 for the applicable hoses and sizes. b. Male straight thread O-ring hose fittings shall be as shown in Figure 2 or the respective styles, and in Table 3 for the applicable hoses and sizes. c.
Male 37 degree flare hose fittings fittings shall be as shown in Figure 3 for the respective styles, and in Table 4 for the applicable hoses and sizes.
d. Female 37 degree flare hose fittings shall be as shown in Figures 4 to 4B for for the respective styles and shapes, and in Tables 5 to 5B for the applicable hoses and sizes. e. Male 45 degree flare hose fittings fittings shall be as shown by the 37 degree figures and tables. f.
Female 45 degree flare hose fittings shall be as shown by the 37 degree figures and tables.
g.
Male flareless 24 degree cone hose fittings shall be as shown in Figure 5 and in Table 6 for the applicable hoses and sizes.
h.
Female flareless 24 degree cone hose fittings shall be as shown in Figures 6 and in Table 7 for the applicable hoses and sizes.
i.
4-bolt split flange hose fittings shall be as shown in Figures 7 to 7F for the respective styles and shapes, and in Tables 8 to 8F for the applicable hoses and sizes.
j.
Female O-ring face seal hose fittings shall be as a s shown in Figures 8 to 8B for the respective styles, and Tables 9 to 9B for the applicable hoses and sizes.
It is recommended that where step sizes or additional types of fittings are required, they be designed to conform with the specifications of this document insofar as they may apply. The following general specifications shall supplement the dimensional data contained in the tables with respect to all unspecified detail.
-2-
SAE J516 Revised JUL2005
2.
References
2.1
Applicable Publications
The following publications form a part of the specification to the extent specified herein. Unless otherwise indicated, the latest revision of SAE publications shall apply. 2.1.1
SAE PUBLICATIONS
Available from SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001. SAE J475—Screw Threads SAE J476—Dryseal Pipe Threads SAE J512—Automotive Tube Fittings SAE J514—Hydraulic Tube Fittings SAE J517—Hydraulic Hose SAE J518—Hydraulic Flanged Tube, Pipe, and Hose Connections, 4-Bolt Split Flange Type SAE J533—Flares for Tubing SAE J846—Coding Systems for Identification of Fluid Conductors and Connectors SAE J1273—Selection, Installation, and Maintenance of Hose and Hose Assemblies SAE J1402—Automotive Air Brake Hose and Hose Assemblies SAE J1453—Fitting—O-Ring Face Seal SAE J1453-1—Specification for O-Ring Face Seal Fittings—Part 1: Tube Connection Details and Common Requirements for Performance and Tests SAE J1926—Specification for Straight Thread O-Ring Boss Port 2.1.2
ISO PUBLICATIONS
Available from ANSI, 25 West 43rd Street, New York, NY 10036-8002. ISO 6162-1—Hydraulic fluid power—Flange connectors with split or one-piece flange clamps and metric or inch screws—Part 1: Flange connectors for use at pressures of 3.5 MPa (35bar) to 35 MPa (350bar) ISO 6162-2—Hydraulic fluid power—Flange connectors with split or one-piece flange clamps and metric or inch screws—Part 2: Flange connectors for use at pressures of 35 MPa (350bar) to 40MPa (400bar) ISO 8434-2—Metallic tube connections for fluid power and general use—Part 2: 37 degree flared connectors ISO 8434-3—Metallic tube connections for fluid power and general use—Part 3: O-ring face seal connectors ISO 11926-2—Connections for general use and fluid power—Ports and stud ends with ISO 725 threads and o-ring sealing—Part 3 light-duty (L series) stud ends ISO 11926-3—Connections for general use and fluid power—Ports and stud ends with ISO 725 threads and o-ring sealing—Part 2 heavy-duty (S series) stud ends 2.1.3
ASTM PUBLICATION
Available from ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959. ASTM B 117—Method of Salt Spray (Fog) Testing
-3-
SAE J516 Revised JUL2005
2.1.4
FMVSS PUBLICATION
Available from the Superintendent of Documents, U. S. Government Printing Office, Mail Stop: SSOP, Washington, DC 20402-9320. FMVSS 106 3.
Size Designations
The hose fitting size is generally designated by the metric hose size together with the nominal pipe or straight thread size or split flange size for the respective fitting types. However, these sizes may also be designated by their SAE dash sizes as follows: 3.1
The hose dash size is equivalent to the number of sixteenth inch increments in the hose size, except in the case of SAE 100R5 and 100R14 hose where it is equivalent to the number of sixteenth inch increments in the outside diameter of tubing having approximately the same inside diameter as the hose. Metric fitting size 6x 6.3 is the same as SAE dash size –4–4.
3.2
The pipe thread dash size is the number of sixteenth inch increments in the nominal pipe thread size.
3.3
The O-ring boss, 37 degree and 45 degree flared, and flareless type thread SAE dash sizes correspond to the number of sixteenth inch increments in the outside diameter of the tubing with which they are designed to be used.
3.4
The 4-bolt split flange SAE dash size is the number of sixteenth inch increments in the flange size.
4.
Hose Fitting (Connector) Identification
All hose fittings, permanently attached and field attachable styles, shall be legibly and permanently marked with the manufacturers name or logo to allow for positive identification. Additional permanent marking is also required to provide a means to idenitfy the proper hose to be used with the hose fitting. Other marking, such as customers assembly number, date code, ect., is permissible as agreed upon by the supplier and user. 5.
Dimensions and Tolerances
Tabulated dimensions shall apply to the finished parts, plated or otherwise processed, as specified by the purchaser. Details of internal construction of the attaching portion of fittings are not specified and shall be optional with the manufacturer, providing the fittings, properly assembled onto the appropriate hose, meet the qualification requirements when the assemblies are subjected to the various tests specified in SAE J517. The maximum and minimum across flat dimensions shall be within the commercial tolerance of bar stock from which the fittings are produced. Formed or upset hexagon contours shall fit standard wrench size openings. The minimum across corners dimensions of external hexagons shall be 1.092 times the nominal width across flats, but shall not result in a side flat width of less than 0.43 times the nominal width across flats. Tolerance on all dimensions not otherwise limited shall be ±0.40 mm. Fitting seats shall be concentric with straight thread pitch diameters within 0.25 mm as measured by full indicator reading (FIR).
-4-
SAE J516 Revised JUL2005
6.
Passages
The tabulated d dimensions reflect the minimum bore at any point through the fitting prior to assembly to the hose. The after assembly bore reduction will be a maximum of 10% starting at metric hose size 8. The 6.3 and smaller d2 dimension is the minimum for after assembly bore. The reduction must be in the general shape of a venturi. Where passages in straight fittings are machined from opposite ends, the offset at the meeting point shall not exceed 0.40 mm. On angle fittings, the cross-sectional area at the junction of fluid passages shall not be less than that of the smallest passage. This assembly passage definition does not apply to bent tubes. 7.
Contour
Details of contour shall be optional with the manufacturer, providing the tabulated dimensions are maintained and serviceability of fittings is not impaired. The recommended wrench clearance dimensions in Appendix A, Table A, represent the width of the fitting hexagon plus sufficient clearance in the shell portion of fitting adjacent to the hexagon to provide adequate space for application of a standard wrench to the hexagon without interfering with mating components during assembly. 8.
Straight Threads
Unified Standard Class 2A external and Class 2B internal threads shall apply to plain finish (unplated) fittings having straight threads designated B. For externally threaded parts with additive finish, the maximum diameters of Class 2A may be exceeded by the amount of the allowance, that is, the basic diameters (Class 2A maximum diameters plus the allowance) shall apply to an externally threaded part after plating. For internally threaded parts with additive finish, the Class 2B diameters apply after plating. The pitch diameter tolerance shall be the same as the corresponding diameter-pitch combination and class of the Unified Fine and 12 thread series. See SAE J475. Where external threads are produced by roll threading and the body is not undercut, the unthreaded portion adjacent to the shoulder may be reduced to the minimum pitch diameter. External threads shall be chamfered and internal threads shall be countersunk as specified in the illustrations and dimensional tables. 9.
Thread Eccentricity Tolerances
The various thread elements of Class 2A external and Class 2B internal threads on hose fittings shall be concentric within the limitations specified under General Specifications in SAE J512. 10.
Pipe Threads
Taper pipe threads designated A in the illustrations and dimensional tables shall conform to the Dryseal American Standard Taper Pipe Thread (NPTF). Specifications are given in detail in SAE J476. The length of full form external thread shall not be shorter than L 2 plus one pitch (thread). Where external pipe threads are produced by roll threading, the diameter of the unthreaded shank adjacent to shoulder may be reduced to the E 2 pitch diameter.
-5-
SAE J516 Revised JUL2005
External pipe threads shall be chamfered from the diameters tabulated in Table 1 to produce the specified length of chamfered or partial thread. Internal pipe threads shall be countersunk 90 degrees, included angle, to the diameters specified in Table 1: TABLE 1—PIPE THREAD DIMENSIONS Dimensions in millimeters Nominal Inch Pipe Thread Size
(1)
11.
External Chamfer (1) Dia Max
External Chamfer (1) Dia Min
Thread Length of Chamfered or Partial Thread Max
1/16 5.8 5.4 0.5 1/8 8.1 7.6 1.4 1/4 10.7 10.2 2.1 3/8 14.0 13.4 2.1 1/2 17.3 16.8 2.7 3/4 22.6 22.1 2.7 1 28.4 27.7 3.3 1-1/4 37.1 36.3 3.3 1-1/2 43.2 42.4 3.3 2 55.1 54.4 3.3 Tabulated diameters conform with Appendix A, SAE J476.
Thread Length of Chamfered or Partial Thread Min
Internal Thread Counter-sink (1) Dia Max
Internal Thread Counter-sink (1) Dia Min
0.3 1.0 1.4 1.4 1.8 1.8 2.2 2.2 2.2 2.2
8.8 11.2 14.5 18.0 22.1 27.4 34.8 43.4 49.5 61.2
8.4 10.7 14.0 17.5 21.6 26.9 34.0 42.7 48.8 60.7
Material
Fittings shall be made from materials of good quality, capable of withstanding the stresses resulting from hydraulic pressures equal to the minimum burst pressure of the applicable hose size and type to which they are assembled without failure. 12.
Finish
The external surfaces and threads of all carbon steel parts shall be plated or coated with a suitable material that passes a 72 h salt spray test in accordance with ASTM B 117. Any appearance of red rust during the 72 h salt spray test shall be considered failure, except for the following: a. All internal fluid passages. b. Edges such as hex points, serrations, and crests of threads where there may be mechanical deformation of the plating or coating typical of mass-produced parts or shipping effects. c. Areas where there is mechanical deformation of the plating or coating caused by crimping, flaring, bending, and other post-plate metal forming operations. d. Areas where the parts are suspended or affixed in the test chamber where condensate can accumulate. NOTE—Hexavalent chromate coatings are not preferred due to environmental reasons. Parts manufactured to this standard after July 1, 2007, shall not be hexavalent chromate coated. Parts intended for commercial and industrial use shall not be cadmium plated. Internal fluid passages shall be protected from corrosion during storage. Changes in plating may affect assembly torques and require requalification, when applicable.
-6-
SAE J516 Revised JUL2005
13.
Workmanship
Workmanship shall conform to the best commercial practice to produce high-quality fittings. Fittings shall be free from all hanging burrs, loose scales, and slivers which might become dislodged in usage, sharp edges, and all other defects that might affect their serviceability. All sealing surfaces must be smooth except that annular tool marks up to 100 min maximum, unless specified otherwise, shall be permissible. 14.
Assembly Considerations
Use of a compatible lubricant in assembling dryseal pipe threads on hose fittings may be desirable to minimize galling and effect a pressure-tight seal. 15.
Pressure Ratings
Some hose pressure ratings in SAE J517 exceed the pressure ratings for the connection (threads, flanges, etc.) of certain types of hose fittings shown in SAE J516. SAE J518 and J1453 specify pressure ratings for 4-bolt split flange and O-ring face seal type hose fittings, respectively. For all other types of hose fitting connections consult the fitting manufacturer for pressure ratings. The pressure rating of a hose assembly comprising SAE J516 fittings and SAE J517 hose shall not exceed the lower of the two pressure rating values.
-7-
SAE J516 Revised JUL2005
NOTE 1 NOTE 2
Connection details in accordance with SAE J512. Method of attachment of fitting to hose is optional.
FIGURE 1—MALE DRYSEAL PIPE THREAD HOSE FITTINGS
TABLE 2—DIMENSIONS OF MALE DRYSEAL PIPE THREAD HOSE FITTINGS Dimensions in millimeters Fitting Size Metric 2 x 3.2 4 x 6.3 6x8 10 x 10 12 x 12.5 20 x 19 25 x 25 32 x 31.5 38 x 38 50 x 51
Fitting Size SAE -1-2 -2-3 -4-4 -6-6 -8-8 -12-12 -16-16 -20-20 -24-24 -32-32
Thread NPTF
a
1/16 1/8 1/4 3/8 1/2 3/4 1 1-1/4 1-1/2 2
d1 Metric Hose Size 3.2 5 6.3 10 12.5 19 25 31.5 38 51
b
c
d
d2 min
L1 min
L2 max
S1 min
1.5 2 3 6 8 13 18 22 28 38
5 5 6 7 8 10 10 11 13 18
40 56 62 83 101 114 132 154 166 216
11.1 11.1 14.3 17.5 22.2 27 34.9 42.9 50.8 63.5
a) Dryseal American Standard Taper Pipe Thread. b) Minimum diameter at any point through the fitting prior to assembly to the hose. The diameter after assembly shall be as described in Paragraph 6. c)
Dimension L2 is measured after assembly.
d) Based on available inch hex sizes.
-8-
SAE J516 Revised JUL2005
NOTE 1 NOTE 2
Connection details in accordance with ISO 11926-2 or ISO 11926-3. Method of attachment of fitting to hose is optional.
FIGURE 2—MALE STRAIGHT THREAD O-RING HOSE FITTINGS
TABLE 3—DIMENSIONS OF MALE STRAIGHT THREAD O-RING HOSE FITTINGS Dimensions in millimeters Fitting Size Metric
Fitting Size SAE
Thread
6x5 6 x 6.3 10 x 10 12 x 10 12 x 12.5 16 x 12.5 16 x 16 20 x 19 22 x 19 25 x 25
-4-3 -4-4 -6-6 -8-6 -8-8 -10-8 -10-10 -12-12 -14-12 -16-16
7/16–20 7/16–20 9/16–18 3/4–16 3/4–16 7/8–14 7/8–14 1-1/16–12 1-3/16–12 1-5/16–12
a
d1 Metric Hose Size 5 6.3 10 10 12.5 12.5 16 19 19 25
b
c
d2 min
L3 min
L4 max
2 3 6 6 8 8 11 14 14 19
4.8 5.6 6.6 6.6 8.6 8.6 8.6 9.1 9.7 12.7
19.0 20.6 25.7 25.7 31.2 31.2 36.8 40.4 40.4 49.5
S2 Standard min 14.3 14.3 17.5 22.2 22.2 25.4 25.4 31.8 34.9 38.1
s2
d
Optional min 15.88 15.88 19.05 23.81 23.81 26.99 26.99 34.93 38.1 41.28
a) In accordance with ISO 725 and ISO 5864, class 2A. b) Minimum diameter at any point through the fitting prior to assembly to the hose. The diameter after assembly shall be as described in Paragraph 6. c) Dimension L4 is measured after assembly. d) Based on available inch hex sizes.
-9-
SAE J516 Revised JUL2005
NOTE 1 NOTE 2
Connection details in accordance with ISO 8434-2. Method of attachment of fitting to hose is optional.
FIGURE 3—MALE 37° FLARE STRAIGHT HOSE FITTINGS (S)
TABLE 4—DIMENSIONS OF MALE 37° FLARE STRAIGHT HOSE FITTINGS (S) Dimensions in millimeters Fitting Size Metric 6 x 6.3 8x8 10 x 10 12 x 12.5 16 x 16 20 x 19 25 x 25 32 x 31.5 38 x 38 50 x 51
Fitting Size SAE -4-4 -5-5 -6-6 -8-8 -10-10 -12-12 -16-16 -20-20 -24-24 -32-32
Thread
a
7/16-20 UNF 1/2-20 UNF 9/16-18 UNF 3/4-16 UNF 7/8-14 UNF 1 1/16-12 UN 1 5/16-12 UN 1 5/8-12 UN 1 7/8-12 UN 2 1/2-12 UN
d1 Metric Hose Size 6.3 8 10 12.5 16 19 25 31.5 38 51
b
c
d2 min
L5 min
L6 max
3 5 6 8 11 14 19 25 30 40
7 7 8 8 10 11 11 13 15 18
75 80 85 100 110 120 135 145 160 225
S3 Standard min 12 14 17 19 24 27 36 46 50 65
d
S3 Optional min 11.1 12.7 14.3 — 22.2 — 33.3 41.3 47.6 63.5
a) In accordance with ISO 725 and ISO 5864, class 2A. b) Minimum diameter at any point through the fitting prior to assembly to the hose. The diameter after assembly shall be as described in Paragraph 6. c) Dimension L6 is measured after assembly. d) Based on available inch hex sizes.
- 10 -
SAE J516 Revised JUL2005
NOTE 1 NOTE 2 NOTE 3
Connection details in accordance with ISO 8434-2. Method of attachment of swivel nut is as chosen by the manufacturer. Method of attachment of fitting to hose is optional.
FIGURE 4—FEMALE 37° FLARE SWIVEL STRAIGHT HOSE FITTINGS (SWS)—2401XX
TABLE 5—DIMENSIONS OF FEMALE 37° FLARE SWIVEL STRAIGHT HOSE FITTINGS (SWS) Dimensions in millimeters Fitting Size Metric
Fitting Size SAE
Thread
6 x 6.3 8x8 10 x 10 12 x 12.5 16 x 16 20 x 19 25 x 25 32 x 31.5 38 x 38 50 x 51
-4-4 -5-5 -6-6 -8-8 -10-10 -12-12 -16-16 -20-20 -24-24 -32-32
7/16-20 UNF 1/2-20 UNF 9/16-18 UNF 3/4-16 UNF 7/8-14 UNF 1 1/16-12 UN 1 5/16-12 UN 1 5/8-12 UN 1 7/8-12 UN 2 1/2-12 UN
a
d1 Metric Hose size 6.3 8 10 12.5 16 19 25 31.5 38 51
b
c
d
d2 min
L7 max
L8 ref
3 5 6 8 11 14 19 25 30 40
75 80 85 100 110 115 140 160 175 210
8.7 9.5 9.5 10.7 12.7 14.3 15.1 15.9 18.6 23.8
S4 Standard min 14 17 19 22 27 32 41 50 65 75
d, e
S4 Optional min 14.3 15.9 17.5 22.2 25.4 31.8 38.1 50.8 57.2 73.0
a) In accordance with ISO 725 and ISO 5864, class 2B. b) Minimum diameter at any point through the fitting prior to assembly to the hose. The diameter after assembly shall be as described in Paragraph 6. c)
Dimension L7 is measured after assembly.
d) In accordance with ISO 4759-1, product grade C. e) Based on available inch hex sizes.
- 11 -
SAE J516 Revised JUL2005
NOTE 1 NOTE 2 NOTE 3
Connection details in accordance with ISO 8434-2. Method of attachment of swivel nut is as chosen by the manufacturer. Method of attachment of fitting to hose is optional.
FIGURE 4A—FEMALE 37° FLARE SWIVEL 45 DEGREE ELBOW HOSE FITTINGS (SWE45)—2403XX
TABLE 5A—DIMENSIONS OF FEMALE 37° FLARE SWIVEL 45 DEGREE ELBOW HOSE FITTINGS (SWE45) Dimensions in millimeters Fitting Size Metric
Fitting Size SAE
Thread
6 x 6.3 8x8 10 x 10 12 x 12.5 16 x 16 20 x 19 25 x 25 32 x 31.5 38 x 38 50 x 51
-4-4 -5-5 -6-6 -8-8 -10-10 -12-12 -16-16 -20-20 -24-24 -32-32
7/16-20 UNF 1/2-20 UNF 9/16-18 UNF 3/4-16 UNF 7/8-14 UNF 1 1/16-12 UN 1 5/16-12 UN 1 5/8-12 UN 1 7/8-12 UN 2 1/2-12 UN
a
d1 Metric Hose Size 6.3 8 10 12.5 16 19 25 31.5 38 51
b
c
d2 min
L9 ±1.5
L10 max
3 5 6 8 11 14 19 25 30 40
10 10 11 15 16 21 24 25 27 34
90 90 95 110 120 145 175 200 240 290
d
S4 Standard min 14 17 19 22 27 32 41 50 60 75
d, e
S4 Optional min 14.3 15.9 17.5 22.2 25.4 31.8 38.1 50.8 57.2 73.0
a) In accordance with ISO 725 and ISO 5864, class 2B. b) Minimum diameter at any point through the fitting prior to assembly to the hose. The diameter after assembly shall be as described in Paragraph 6. c) Dimension L10 is measured after assembly. d) In accordance with ISO 4759-1, product grade C. e) Based on available inch hex sizes.
- 12 -
SAE J516 Revised JUL2005
NOTE 1 NOTE 2 NOTE 3
Connection details in accordance with ISO 8434-2. Method of attachment of swivel nut is as chosen by the manufacturer. Method of attachment of fitting to hose is optional.
FIGURE 4B—FEMALE 37° FLARE SWIVEL 90 DEGREE ELBOW HOSE FITTINGS [SHORT (SWES), MEDIUM (SWEM) AND LONG (SWEL)]—2414XX
TABLE 5B—FEMALE 37° FLARE SWIVEL 45 DEGREE ELBOW HOSE FITTINGS [SHORT (SWES), MEDIUM (SWEM) AND LONG (SWEL)] Dimensions in millimeters Fitting Size Metric
Fitting Size SAE
Thread
6 x 6.3 8x8 10 x 10 12 x 12.5 16 x 16 20 x 19 25 x 25 32 x 31.5 38 x 38 50 x 51
-4-4 -5-5 -6-6 -8-8 -10-10 -12-12 -16-16 -20-20 -24-24 -32-32
7/16-20 UNF 1/2-20 UNF 9/16-18 UNF 3/4-16 UNF 7/8-14 UNF 1 1/16-12 UN 1 5/16-12 UN 1 5/8-12 UN 1 7/8-12 UN 2 1/2-12 UN
a
d1 Metric Hose Size 6.3 8 10 12.5 16 19 25 31.5 38 51
b
d2 min 3 5 6 8 11 14 19 25 30 40
c
L11 ± 1.5 SWES 21 21 23 29 32 48 56 64 69 88
d
L12 ± 1.5 SWEM 32 32 38 41 47 58 71 78 86 140
e
L13 ± 1.5 SWEL 46 46 54 64 70 96 114 129 141 222
f
L14 max 85 85 90 100 110 140 170 200 230 280
g
S4 Standard min 14 17 19 22 27 32 41 50 60 75
g, h
S4 h Optional min 14.3 15.9 17.5 22.2 25.4 31.8 38.1 50.8 57.2 73.0
a) In accordance with ISO 725 and ISO 5864, class 2B. b) Minimum diameter at any point through the fitting prior to assembly to the hose. The diameter after assembly shall be as described in Paragraph 6. c) Short drop (SWES) dimensions. See Appendix B. d) Medium drop (SWEM) dimensions. Medium drop hose fittings will clear 90 degrees adjustable stud elbow (SDE) per ISO 8434-2. See Appendix B. e) Long drop (SWEL) dimensions. Long drop hose fittings will clear short drop (SWES) hose fittings. See Appendix B. f)
Dimension L14 is measured after assembly.
g) In accordance with ISO 4759-1, product grade C. h) Based on available inch hex sizes.
- 13 -
SAE J516 Revised JUL2005
NOTE 1 NOTE 2
Connection details in accordance with SAE J514. Method of attachment of hose fitting to hose is optional.
FIGURE 5—MALE FLARELESS 24° CONE STRAIGHT HOSE FITTINGS
TABLE 6—DIMENSIONS OF MALE FLARELESS 24° CONE STRAIGHT HOSE FITTINGS Dimensions in millimeters Fitting Size Metric
Fitting Size SAE
Thread
6 x 6.3 8 x 10 10 x 10 12 x 10 12 x 12.5 16 x 12.5 16 x 16 20 x 16 16 x 19 20 x 19 25 x 25
-4-4 -5-6 -6-6 -8-6 -8-8 -10-8 -10-10 -12-10 -10-12 -12-12 -16-16
7/16–20 9/16–18 9/16–18 3/4–16 3/4–16 7/8–14 7/8–14 1-1/16–12 7/8–14 1-1/16–12 1-5/16–12
a
d1 Metric Hose Size 6.3 10 10 10 12.5 12.5 16 16 19 19 25
min
L15 min
L16 max
S5 Standard min
3 5 6 6 8 8 11 11 14 14 19
5.6 5.6 5.6 6.4 6.4 6.4 6.4 7.9 7.9 7.9 9.7
61 61 62 65 74 76 83 88 90 90 102
12 17 17 19 19 24 24 27 24 27 36
d2
b
c
d
S5 e Optional min 11.1 14.3 14.3 19.0 19.0 22.2 22.2 31.8 22.2 31.8 38.1
a) In accordance with ISO 725 and ISO 5864, class 2A. b) Minimum diameter at any point through the fitting prior to assembly to the hose. The diameter after assembly shall be as described in Paragraph 6. c)
Dimension L16 is measured after assembly.
d) Based on available inch hex sizes.
- 14 -
SAE J516 Revised JUL2005
NOTE 1 NOTE 2 NOTE 3
Connection details in accordance with SAE J514. Method of attachment of swivel nut is as chosen by the manufacturer. Method of attachment of hose fitting to hose is optional.
FIGURE 6—FEMALE FLARELESS 24° CONE SWIVEL STRAIGHT HOSE FITTINGS
TABLE 7—DIMENSIONS OF FEMALE FLARELESS 24° CONE SWIVEL STRAIGHT HOSE FITTINGS Dimensions in millimeters Fitting Size Metric
Fitting Size SAE
Thread
6 x 6.3 10 x 8 10 x 10 12 x 10 12 x 12.5 16 x 12.5 16 x 16 20 x 16 16 x 19 20 x 19 25 x 25
-4-4 -6-5 -6-6 -8-6 -8-8 -10-8 -10-10 -12-10 -10-12 -12-12 -16-16
7/16–20 9/16–18 9/16–18 3/4–16 3/4–16 7/8–14 7/8–14 1-1/16–12 7/8–14 1-1/16–12 1-5/16–12
a)
a
d1 Metric Hose Size 6.3 8 10 10 12.5 12.5 16 16 19 19 25
b
c
d2 min
L17 ref
L18 max
3 5 6 6 8 8 11 11 14 14 19
16.61 18.29 18.29 20.45 20.45 22.35 22.35 23.11 22.35 23.11 27.30
66.5 67.6 70.6 73.9 82.3 83.1 89.4 92.2 92.2 92.2 108.7
d
S6 Standard min 14 19 19 22 22 27 27 32 27 32 41
d, e
S6 Optional min 14.3 17.5 17.5 22.2 22.2 25.4 25.4 31.8 25.4 31.8 38.1
In accordance with ISO 725 and ISO 5864, class 2B.
b) Minimum diameter at any point through the fitting prior to assembly to the hose. The diameter after assembly shall be as described in Paragraph 6. c)
Dimension L18 is measured after assembly.
d) e)
In accordance with ISO 4759-1, product grade C. Based on available inch hex sizes.
- 15 -
SAE J516 Revised JUL2005
NOTE 1 NOTE 2
Connection details and O-rings in accordance with ISO 6162-1 and ISO 6162-2. Method of attachment of hose fitting to hose is optional.
FIGURE 7—4-BOLT SPLIT FLANGE STRAIGHT HOSE FITTINGS (S)
TABLE 8—DIMENSIONS OF 4-BOLT SPLIT FLANGE STRAIGHT HOSE F ITTINGS (S) Dimensions in millimeters Fitting Size Metric
Fitting Size SAE
13 x 12,5 19 x 19 25 x 25 32 x 31,5 38 x 38 51 x 51 64 x 64 76 x 76
-8-8 -12-12 -16-16 -20-20 -24-24 -32-32 -40-40 -48-48
d1 Metric Hose Size 12.5 19 25 31.5 38 51 64 76
a
d2 min 8 14 19 25 31 42
d3 0.25 S-L 30.2 38.1 44.5 50.8 60.3 71.4 84.1 101.6
d3 0.25 S-S 31.8 41.3 47.6 54 63.5 79.4
b
L19 max 100 140 150 175 200 240
a) Minimum diameter at any point through the fitting prior to assembly to the hose. The diameter after assembly shall be as described in Paragraph 6. b) Dimension L19 is measured after assembly.
- 16 -
SAE J516 Revised JUL2005
NOTE 1 NOTE 2
Connection details and O-rings in accordance with SAE J518, ISO 6162-1 and ISO 6162-2. Method of attachment of hose fitting to hose is optional.
FIGURE 7A—4-BOLT SPLIT FLANGE 22 1/2 DEGREE ELBOW HOSE FITTINGS
TABLE 8A—DIMENSIONS OF 4-BOLT SPLIT FLANGE 22 1/2 DEGREE ELBOW HOSE FITTINGS (E22) Dimensions in millimeters Fitting Size Metric 13 x 12.5 19 x 12.5 19 x 19 25 x 19 25 x 25 32 x 25 32 x 31.5 38 x 38 51 x 51 64 x 64 76 x 76
Fitting Size SAE -8-8 -12-8 -12-12 -16-12 -16-16 -20-16 -20-20 -24-24 -32-32 -40-40 -48-48
d1 Metric Hose Size 12.5 12.5 19 19 25 25 31.5 38 51 64 76
a
d2 min 8 8 14 14 19 19 25 31 42 57 68
d3 0.25 E22M-L 30.2 38.1 38.1 44.5 44.5 50.8 50.8 60.3 71.4 84.1 101.6
d3 0.25 E22M-S 31.8 41.3 41.3 47.6 47.6 54 54 63.5 79.4
b
L20 3
L21 max
9 11 11 14 14 15 15 18 22 16 18
105 115 135 170 170 193 205 250 305 173 185
a) Minimum diameter at any point through the fitting prior to assembly to the hose. The diameter after assembly shall be as described in Paragraph 6. b) Dimension L21 is measured after assembly.
- 17 -
SAE J516 Revised JUL2005
NOTE 1 NOTE 2
Connection details and O-rings in accordance with ISO 6162-1 and ISO 6162-2. Method of attachment of hose fitting to hose is optional.
FIGURE 7B—4-BOLT SPLIT FLANGE 30 DEGREE ELBOW HOSE FITTINGS
TABLE 8B—DIMENSIONS OF 4-BOLT SPLIT FLANGE 30 DEGREE ELBOW HOSE FITTINGS (E30) Dimensions in millimeters Fitting Size Metric
Fitting Size SAE
d1 Metric Hose Size
d2 min
13 x 12.5 19 x 12.5 19 x 19 25 x 19 25 x 25 32 x 25 32 x 31.5 38 x 38 51 x 51 64 x 64 76 x 76
-8-8 -12-8 -12-12 -16-12 -16-16 -20-16 -20-20 -24-24 -32-32 -40-40 -48-48
12.5 12.5 19 19 25 25 31.5 38 51 64 76
8 8 14 14 19 19 25 31 42 57 68
a
d3 0.25 E30S-L E30M-L 30.2 38.1 38.1 44.5 44.5 50.8 50.8 60.3 71.4 84.1 101.6
d3 0.25 E30S-S E30M-S 31.8 41.3 41.3 47.6 47.6 54 54 63.5 79.4
b
L22 3 E30S-L E30S-S ––– ––– ––– ––– ––– ––– b
20 b 25 23.9 28.4
b
L22 3 E30M-L E30M-S 12 16 16 19 19 22 22 30 32
c
L23 max 105 125 145 170 170 188 200 245 300 186 209
a) Minimum diameter at any point through the fitting prior to assembly to the hose. The diameter after assembly shall be as described in Paragraph 6. b) Short drop (E30S-L and E30S-S) hose fittings in flange sizes 32 and larger may not be manufactured by preferred methods with ratings suitable for use with high pressure spiral wire hose, which is typically used at working pressures of 21 MPa or 17.5 MPa and higher in hose sizes 31.5 and 38, respectively. Use preferred medium drop (E30M-L or E30M-S) hose fittings or consult manufacturer for availability. c) Dimension L23 is measured after assembly.
- 18 -
SAE J516 Revised JUL2005
NOTE 1 NOTE 2
Connection details and O-rings in accordance with ISO 6162-1 and ISO 6162-2. Method of attachment of hose fitting to hose is optional.
FIGURE 7C—4-BOLT SPLIT FLANGE 45 DEGREE ELBOW HOSE FITTINGS
TABLE 8C—DIMENSIONS OF 4-BOLT SPLIT FLANGE 45 DEGREE ELBOW HOSE FITTINGS (E45) Dimensions in millimeters Fitting Size Metric
Fitting Size SAE
d1 Metric Hose Size
d2 min
13 x 12.5 19 x 12.5 19 x 19 25 x 19 25 x 25 32 x 25 32 x 31.5 38 x 38 51 x 51 64 x 64 76 x 76
-8-8 -12-8 -12-12 -16-12 -16-16 -20-16 -20-20 -24-24 -32-32 -40-40 -48-48
12.5 12.5 19 19 25 25 31.5 38 51 64 76
8 8 14 14 19 19 25 31 42 57 68
a
d3 0.25 E45S-L E45M-L 30.2 38.1 38.1 44.5 44.5 50.8 50.8 60.3 71.4 84.1 101.6
d3 0.25 E45S-S E45M-S 31.8 41.3 41.3 47.6 47.6 54 54 63.5 79.4
b
L24 3 E45S-L E45S-S ––– ––– ––– ––– b
28 –––
b
32 b 38 b 52 43.7 51.6
b
L24 3 E45M-L E45M-S 19 26 26 32 32 38 38 44 56
c
L25 max 105 125 145 175 175 188 200 240 290 197 234
a) Minimum diameter at any point through the fitting prior to assembly to the hose. The diameter after assembly shall be as described in Paragraph 6. b) Short drop (E45S-L and E45S-S) hose fittings in flange sizes 25 and larger may not be manufactured by preferred methods with ratings suitable for use with high pressure spiral wire hose, which is typically used at working pressures of 28 MPa, 21 MPa, 17.5 MPa or 14 MPa and higher in hose sizes 25, 31.5, 38 and 51, respectively. Use preferred medium drop (E45M-L or E45M-S) hose fittings or consult manufacturer for availability. c) Dimension L25 is measured after assembly.
- 19 -
SAE J516 Revised JUL2005
NOTE 1 NOTE 2
Connection details and O-rings in accordance with ISO 6162-1 and ISO 6162-2. Method of attachment of hose fitting to hose is optional.
FIGURE 7D—4-BOLT SPLIT FLANGE 60 DEGREE ELBOW HOSE FITTINGS
TABLE 8D—DIMENSIONS OF 4-BOLT SPLIT FLANGE 60 DEGREE ELBOW HOSE FITTINGS (E60) Dimensions in millimeters Fitting Size Metric
Fitting Size SAE
d1 Metric Hose Size
d2 min
13 x 12.5 19 x 12.5 19 x 19 25 x 19 25 x 25 32 x 25 32 x 31.5 38 x 38 51 x 51 64 x 64 76 x 76
-8-8 -12-8 -12-12 -16-12 -16-16 -20-16 -20-20 -24-24 -32-32 -40-40 -48-48
12.5 12.5 19 19 25 25 31.5 38 51 64 76
8 8 14 14 19 19 25 31 42 57 68
a
d3 0.25 E60S-L E60M-L 30.2 38.1 38.1 44.5 44.5 50.8 50.8 60.3 71.4 84.1 101.6
d3 0.25 E60S-S E60M-S 31.8 41.3 41.3 47.6 47.6 54 54 63.5 79.4
b
L26 3 E60S-L E60S-S ––– ––– ––– ––– ––– ––– b
45 b 53 b 75 66.8 79.2
b
L26 3 E60M-L E60M-S 27 37 37 44 44 55 55 64 83
c
L27 max 110 125 145 180 180 218 230 280 310 207 246
a) Minimum diameter at any point through the fitting prior to assembly to the hose. The diameter after assembly shall be as described in Paragraph 6. b) Short drop (E60S-L and E60S-S) hose fittings in flange sizes 32 and larger may not be manufactured by preferred methods with ratings suitable for use with high pressure spiral wire hose, which is typically used at working pressures of 21 MPa, 17.5 MPa or 14 MPa and higher in hose sizes 31.5, 38 and 51, respectively. Use preferred medium drop (E60M-L or E60M-S) hose fittings or consult manufacturer for availability. c) Dimension L27 is measured after assembly.
- 20 -
SAE J516 Revised JUL2005
NOTE 1 NOTE 2
Connection details and O-rings in accordance with ISO 6162-1 and ISO 6162-2. Method of attachment of hose fitting to hose is optional.
FIGURE 7E—4-BOLT SPLIT FLANGE 67 1/2 DEGREE ELBOW HOSE FITTINGS
TABLE 8E—DIMENSIONS OF 4-BOLT SPLIT FLANGE 67 1/2 DEGREE ELBOW HOSE FITTINGS (E67) Dimensions in millimeters Fitting Size Metric
Fitting Size SAE
d1 Metric Hose Size
d2 min
13 x 12.5 19 x 12.5 19 x 19 25 x 19 25 x 25 32 x 25 32 x 31.5 38 x 38 51 x 51 64 x 64 76 x 76
-8-8 -12-8 -12-12 -16-12 -16-16 -20-16 -20-20 -24-24 -32-32 -40-40 -48-48
12.5 12.5 19 19 25 25 31.5 38 51 64 76
8 8 14 14 19 19 25 31 42 57 68
a
d3 0.25 E67S-L E67M-L 30.2 38.1 38.1 44.5 44.5 50.8 50.8 60.3 71.4 84.1 101.6
d3 0.25 E67S-S E67M-S 31.8 41.3 41.3 47.6 47.6 54 54 63.5 79.4
b
L28 3 E67S-L E67S-S ––– ––– ––– ––– ––– ––– b
51 b 61 b 85 79.2 94.5
b
L28 3 E67M-L E67M-S 30 42 42 51 51 64 64 74 97
c
L29 max 105 125 145 175 175 208 220 260 300 209 242
a) Minimum diameter at any point through the fitting prior to assembly to the hose. The diameter after assembly shall be as described in Paragraph 6. b) Short drop (E67S-L and E67S-S) hose fittings in flange sizes 32 and larger may not be manufactured by preferred methods with ratings suitable for use with high pressure spiral wire hose, which is typically used at working pressures of 21 MPa, 17.5 MPa or 14 MPa and higher in hose sizes 31.5, 38 and 51, respectively. Use preferred medium drop (E67M-L or E67M-S) hose fittings or consult manufacturer for availability. c) Dimension L29 is measured after assembly.
- 21 -
SAE J516 Revised JUL2005
NOTE 1 NOTE 2
Connection details and O-rings in accordance with ISO 6162-1 and ISO 6162-2. Method of attachment of hose fitting to hose is optional.
FIGURE 7F—4-BOLT SPLIT FLANGE 90 DEGREE ELBOW HOSE FITTINGS
TABLE 8F—DIMENSIONS OF 4-BOLT SPLIT FLANGE 90 DEGREE ELBOW HOSE FITTINGS (E) Dimensions in millimeters Fitting Size Metric
Fitting Size SAE
d1 Metric Hose Size
d2 min
13 x 12.5 19 x 12.5 19 x 19 25 x 19 25 x 25 32 x 25 32 x 31.5 38 x 38 51 x 51 64 x 64 76 x 76
-8-8 -12-8 -12-12 -16-12 -16-16 -20-16 -20-20 -24-24 -32-32 -40-40 -48-48
12.5 12.5 19 19 25 25 31.5 38 51 64 76
8 8 14 14 19 19 25 31 42 57 68
d3 0.25 ES-L EM-L 30.2 38.1 38.1 44.5 44.5 50.8 50.8 60.3 71.4 84.1 101.6
a
d3 0.25 ES-S EM-S 31.8 41.3 41.3 47.6 47.6 54 54 63.5 79.4
b
L30 3 ES-L ES-S ––– ––– ––– ––– 61 b
68 b 68 b 81 b 120 117.3 140.7
b
L30 3 EM-L EM-S 40 58 58 70 70 90 90 104 138
c
L31 max 100 120 140 170 170 188 200 230 280 210 250
a) Minimum diameter at any point through the fitting prior to assembly to the hose. The diameter after assembly shall be as described in Paragraph 6. b) Short drop (ES-L and ES-S) hose fittings in flange sizes 32 and larger may not be manufactured by preferred methods with ratings suitable for use with high pressure spiral wire hose, which is typically used at working pressures of 28 MPa, 21 MPa, 17.5 MPa or 14 MPa and higher in hose sizes 25, 31.5, 38 and 51, respectively. Use preferred medium drop (EM-L or EM-S) hose fittings or consult manufacturer for availability. c) Dimension L31 is measured after assembly.
- 22 -
SAE J516 Revised JUL2005
STYLE B (5301XX B) SHOWN WITH SEALING SURFACE EXPOSED
STYLE A (5301XX A)
NOTE 1 NOTE 2 NOTE 2
Connection details in accordance with ISO 8434-3. Method of attachment of swivel nut is as chosen by the manufacturer. Method of attachment of hose fitting to hose is optional.
FIGURE 8—FEMALE O-RING FACE SEAL SWIVEL STRAIGHT HOSE FITTINGS (SWSA AND SWSB)
TABLE 9—DIMENSIONS OF FEMALE O-RING FACE SEAL SWIVEL STRAIGHT HOSE FITTINGS (SWSA AND SWSB) Dimensions in millimeters Fitting Size Metric
Fitting Size SAE
Thread
6 x 6.3 6x8 10 x 6.3 10 x 8 10 x 10 12 x 10 12 x 12.5 16 x 16 20 x 19 25 x 25 30 x 31.5 38 x 38
-4-4 -4-5 -6-4 -6-5 -6-6 -8-6 -8-8 -10-10 -12-12 -16-16 -20-20 -24-24
9/16-18 UNF 9/16-18 UNF 11/16-16 UNF 11/16-16 UNF 11/16-16 UNF 13/16-16 UN 13/16-16 UN 1-14 UNS 1 3/16-12 UN 1 7/16-12 UN 1 11/16-12 UN 2-12 UN
a
d
d
e
e, f
d1 Metric Hose size
d2 min
L32 min
L33 min
L34 max SWSA
L34 max SWSB
S7 Standard min
S7 Optional min
6.3 8 6.3 8 10 10 12.5 16 19 25 31.5 38
3 5 3 5 6 6 8 11 14 19 25 31
6 6 6 6 6 6 6 6 7 8 9 9
6.5 6.5 6.5 6.5 6.5 8 8 9.5 9.5 11 12.5 15.5
70 75 73 78 80 85 90 95 100 105 125 150
80 85 83 88 90 95 100 110 115 120 140 170
17 17 22 22 22 24 24 30 36 41 50 60
17.5 17.5 20.6 20.6 20.6 23.8 23.8 28.6 34.9 41.3 47.6
b
c
a) In accordance with ASME/B1.1 and ISO 5864, class 2B (except for 1-14 UNS-2B thread. the dimensions of which are given in ISO 8434-3, Annex A). b) Minimum diameter at any point through the fitting prior to assembly to the hose. The diameter after assembly shall be as described in Paragraph 6. c)
Crimp style nut is permissible, but width of hexagonal head shall meet L 33 minimum.
d) Dimension L34 is measured after assembly. e) In accordance with ISO 4759-1, product grade C. f) Based on available inch hex sizes.
- 23 -
SAE J516 Revised JUL2005
NOTE 1 NOTE 2 NOTE 2
Connection details in accordance with ISO 8434-3. Method of attachment of swivel nut is as chosen by the manufacturer. Method of attachment of hose fitting to hose is optional.
FIGURE 8A—FEMALE O-RING FACE SEAL SWIVEL 45 DEGREE ELBOW HOSE FITTINGS (SWE45)
TABLE 9A—DIMENSIONS OF FEMALE O-RING FACE SEAL SWIVEL 45 DEGREE ELBOW HOSE FITTINGS (SWE45) Dimensions in millimeters Fitting Size Metric
Fitting Size SAE
Thread
6 x 6.3 10 x 8 10 x 10 12 x 12.5 16 x 16 20 x 19 25 x 25 30 x 31.5 38 x 38
-4-4 -6-5 -6-6 -8-8 -10-10 -12-12 -16-16 -20-20 -24-24
9/16-18 UNF 11/16-16 UNF 11/16-16 UNF 13/16-16 UN 1-14 UNS 1 3/16-12 UN 1 7/16-12 UN 1 11/16-12 UN 2-12 UN
a
c
c, d
d1 Metric Hose size
d2 min
L35 1.5 SWE45S
L35 1.5 SWE45M
L36 max SWE45S
6.3 8 10 12.5 16 19 25 31.5 38
3 5 6 8 11 14 19 25 31
10 11 11 15 16 21 24 c 25 c 27
––– ––– ––– ––– ––– ––– ––– 32 42
90 98 100 110 120 125 130 c 170 c 190
b
d
e, f
L36 S7 max Standard SWE45M min ––– ––– ––– ––– ––– ––– ––– 177 205
17 22 22 24 30 36 41 50 60
e, f, g
S7 Optional min 17.5 20.6 20.6 23.8 28.6 34.9 41.3 47.6
a) In accordance with ASME/B1.1 and ISO 5864, class 2B (except for 1-14 UNS-2B thread. the dimensions of which are given in ISO 8434-3, Annex A). b) Minimum diameter at any point through the fitting prior to assembly to the hose. The diameter after assembly shall be as described in Paragraph 6. c) Short drop (SWE45S) hose fittings in connection sizes 30 and 38 may not be manufactured by preferred methods with ratings suitable for use with high pressure spiral wire hose, which is typically used at working pressures of 21 MPa or 17.5 MPa and higher in hose sizes 31.5 and 38, respectively. Use preferred medium drop (SWE45M) hose fittings or consult manufacturer for availability. d) Dimension L34 is measured after assembly. e) In accordance with ISO 4759-1, product grade C. f)
Crimp style nut is permissible, but width of hexagonal head shall meet L 33 minimum from Table 9.
g) Based on available inch hex sizes.
- 24 -
SAE J516 Revised JUL2005
NOTE 1 NOTE 2 NOTE 2
Connection details in accordance with ISO 8434-3. Method of attachment of swivel nut is as chosen by the manufacturer. Method of attachment of hose fitting to hose is optional.
FIGURE 8B—FEMALE O-RING FACE SEAL SWIVEL 90 DEGREE ELBOW HOSE FITTINGS (SWE)
TABLE 9B—DIMENSIONS OF FEMALE O-RING FACE SEAL SWIVEL 90 DEGREE ELBOW HOSE FITTINGS (SWE) Dimensions in millimeters Fitting Size Metric
Fitting Size SAE
Thread
6 x 6.3 10 x 8 10 x 10 12 x 12.5 16 x 16 20 x 19 25 x 25 30 x 31.5 38 x 38
-4-4 -6-5 -6-6 -8-8 -10-10 -12-12 -16-16 -20-20 -24-24
9/16-18 UNF 11/16-16 UNF 11/16-16 UNF 13/16-16 UN 1-14 UNS 1 3/16-12 UN 1 7/16-12 UN 1 11/16-12 UN 2-12 UN
a
d1 Metric Hose Size 6.3 8 10 12.5 16 19 25 31.5 38
b
d2 min 3 5 6 8 11 14 19 25 31
c
L37 ± 1.5 SWES 21 23 23 29 32 48 56 c
64 c 69
d
L38 ± 1.5 SWEM 32 38 38 41 47 58 71 78 86
e
L39 ± 1.5 SWEL 46 54 54 64 70 96 114 129 141
f
L40 max 90 98 100 110 120 125 130 170 190
g, h
S7 Standard min 17 22 22 24 30 36 41 50 60
g, h, i
S7 h Optional min 17.5 20.6 20.6 23.8 28.6 34.9 41.3 47.6
a) In accordance with ASME/B1.1 and ISO 5864, class 2B (except for 1-14 UNS-2B thread. the dimensions of which are given in ISO 8434-3, Annex A). b) Minimum diameter at any point through the fitting prior to assembly to the hose. The diameter after assembly shall be as described in Paragraph 6. c) Short drop (SWES) hose fittings in connection sizes 30 and 38 may not be manufactured by preferred methods with ratings suitable for use with high pressure spiral wire hose, which is typically used at working pressures of 21 MPa or 17.5 MPa and higher in hose sizes 31.5 and 38, respectively. Use preferred medium drop (SWEM) hose fittings or consult manufacturer for availability. d) Medium drop (SWEM) dimensions. Medium drop hose fittings will clear 90 degrees adjustable stud elbow (SDE) per ISO 8434-3. See Appendix B. e) Long drop (SWEL) dimensions. Long drop hose fittings will clear short drop (SWES) hose fittings. See Appendix B. f)
Dimension L40 is measured after assembly.
g) In accordance with ISO 4759-1, product grade C. h) Crimp style nut is permissible, but width of hexagonal head shall meet L 33 minimum from Table 9. i)
Based on available inch hex sizes.
- 25 -
SAE J516 Revised JUL2005
16.
Notes
16.1 Marginal Indicia The change bar (l) located in the left margin is for the convenience of the user in locating areas where technical revisions have been made to the previous issue of the report. An (R) symbol to the left of the document title indicates a complete revision of the report.
PREPARED BY THE SAE FLUID CONDUCTORS AND CONNECTORS TECHNICAL COMMITTEE SC2— HYDRAULIC HOSE AND HOSE FITTINGS
- 26 -
SAE J516 Revised JUL2005
APPENDIX A
TABLE A1—WRENCH CLEARANCE
SAE Dash Size
Nominal Straight Thread Size
Hex Size inch
Hex Size mm
Recommended Wrench Clearance Min mm
-2
5/16-24
7/16
11.100
8.8
-3
3/8-24
1/2
12.700
10.4
-4
7/16-20
9/16
14.288
11.2
-5
1/2-20
5/8
15.875
11.2
-6
9/16-18
11/16
17.463
11.6
-8
3/4-16
7/8
22.225
15.5
-10
7/8-14
1
25.400
17.5
-12
1-1/16-12
1-1/4
31.750
20.7
-14
1-3/16-12
1-3/8
34.925
21.5
-16
1-5/16-12
1-1/2
38.100
23.9
-20
1-5/8-12
1-7/8
47.625
27.1
-24
1-7/8-12
2-1/8
53.975
27.1
-32
2-1/2-12
2-3/4
69.850
27.1
- 27 -
SAE J516 Revised JUL2005
APPENDIX B
FIGURE B1
FIGURE B2
- 28 -
