ROUTE v7 Chapter 1 Exam _ CCNP v7 Exam Module Question & Answer

17/10/2016

ROUTE v7 Chapter 1 Exam | CCNP v7 Exam Module Question & Answer

CCNP v7 Exam Module Question & Answer

ROUTE V7 CHAPTER 1 EXAM JUNE 29, 2016 | ADMIN | LEAVE A COMMENT

Question 1  Which two major areas can be used when discussing the high-level overview of a typical enterprise network? Choose two.     Campus backbone     Building distribution     Building access

    Enterprise campus

    Enterprise edge

 Question

2 Which

of the following is used when choosing a dynamic routing protocol?  Choose two.      Cost of equipment     Knowledge level of a specific routing protocol     Scalability     Type of links supported

 Question

3  BGP is which type of protocol?

    Distance vector     Advanced distance vector     Link-state     Path vector

Question 4 Which two factors can influence convergence time for a routing protocol?  Choose two.      Fine tuning routing protocol timers           Number of end devices with IP addresses. http://ccnpv7.com/2016/06/29/route-v7-chapter-1-exam/

1/5

17/10/2016

ROUTE v7 Chapter 1 Exam | CCNP v7 Exam Module Question & Answer

    Configuring route summarization     Implementing authentication

Question 5 Scalability of a network includes which two factors? Choose two.     Number of adjacent neighbors     Number of routers     Distance between routers     Ability to do auto summarization

 Question

6 Which

of the following traffic types is not supported by IPv6?      Unicast     Multicast     Anycast     Broadcast

Question 7 What is the IPv6 multicast address used by EIGRP?   FF02::5     FF02::6     FF02::9

    FF02::A Question 8 Which type of IPv6 address is used by routing protocols for communications only on the link?     Unique local     Site local

    Link-local     Multicast

Question 9 Which type of ICMPv6 message is sent by a device to request information about the network such as the prefix, prefix length and default gateway?      Neighbor Advertisement     Neighbor Solicitation     Router Advertisement

http://ccnpv7.com/2016/06/29/route-v7-chapter-1-exam/

2/5

17/10/2016

ROUTE v7 Chapter 1 Exam | CCNP v7 Exam Module Question & Answer

    Router Solicitation

Question 10 Which type of ICMPv6 message is sent by a device to inform another device of its IPv6 address and associated Ethernet address? Correct!   Neighbor Advertisement    Neighbor Solicitation    Router Advertisement    Router Solicitation   

Question 11 Which type of network allows access to multiple devices on the same network but does not provide broadcast capabilities?      Point-to-point     Broadcast     NBMA     Multi-access   

Question 12 Which type of subinterface provides connections similar to physical point-to-point links and has no neighbor discovery issues?  Correct!   Point-to-point    Point-to-multipoint    Multipoint    All of the above

Question 13  Which tunneling protocol was developed by Cisco to encapsulate a Layer 3 protocol inside a point-to-point, tunnel-over-IP network? Correct!     GRE      DMVPN     IPsec     MPLS

Question 14  A Layer 3 MPLS VPN over GRE is an example of what type of VPN?      DMVPN     Multi-VPN     Combination VPN     Hybrid VPN http://ccnpv7.com/2016/06/29/route-v7-chapter-1-exam/

3/5

17/10/2016

ROUTE v7 Chapter 1 Exam | CCNP v7 Exam Module Question & Answer

  

Question 15 What protocol is used by routers implementing DMVPN to determine the next-hop IP address in tunneling networks?     Dynamic GRE

    NHRP     mGRE     MPLS

Question 16 What framework of open standards that provides confidentiality, data integrity, authentication and anti-replay protection? Correct!     IPsec    VPN     PAP     PSK   

Question 17 R1 has an adjacent RIPng neighbor R2. R1 has a LAN with no neighbors, 2001:DB8:ACAD:1::/64. R1 advertises this prefix to adjacent RIPng neighbor, R2. What metric does R2 display for 2001:DB8:ACAD:1::/64?      1 hop

    2 hops    3 hops     4 hops   

Question 18 How is an interface enabled for RIPng?  You nswered    Using the network prefix/prefix-length router mode command    Using the ipv6 rip name enable interface command     Interfaces are automatically enabled for RIPng when the RIPng process is started     Using the router ripng name interface command

Question 19 Router R1 has multiple routes in its routing table including RIPng routes, directly connected networks and a static default route. R2 http://ccnpv7.com/2016/06/29/route-v7-chapter-1-exam/

4/5

17/10/2016

ROUTE v7 Chapter 1 Exam | CCNP v7 Exam Module Question & Answer

receives a default route from R1 but no other routes. This is because R1 uses which option at the end of ipv6 rip name default-information interface command?   static   originate   default-onlyCorrect!   only CCNP V7 ANSWERS

http://ccnpv7.com/2016/06/29/route-v7-chapter-1-exam/

5/5