Download Roboguide Training Manual [FRDE][Z KAE TRN Roboguide 1 01 en]...
Accompanying Training Manual Roboguide V6.40 Rev.B
Name:
Z-KAE-TRN-Roboguide-1/01
1
© Copyright
FANUC Robotics Deutschland GmbH
Do not copy this document or parts of this document and give it to a third party without the express written permission of FANUC. Other than the described functions may run on the controller. However, you do not have any rights to claim these functions at delivery. We have checked the contents of this document for correspondence with the described hardware and software. However, we do not ensure full correspondence. We do, however, regularly check the contents of this document and make necessary corrections in the succeeding editions. Design and specifications that do not affect the functioning are subject to change without notice. Author: Werner Schollenberger
Z-KAE-TRN-Roboguide-1/01
2
Preface
Training your staff is the key to your success A profound training of your staff is the key to your success. Training your staff means to give them the necessary information to be able to control the system and understand the applied technology. General knowledge as well as detailed knowledge about the system is as important as the practical knowledge of the applied programming. This is the aim of our training concept. Our training is a successful mix of well explained theory and practical applications. To guarantee a successful training, we use detailed training documents, state-of-the-art training methods and means in our training center in Neuhausen. More than two thirds of the course are reserved for training on the machine. Your staff collects practical knowledge of the robot and the appropriate application programs. A qualified training means for you: Maximum utilization ... of the system and optimum cycle times through professional programming. Long service life ... and insignificant wear because of qualified maintenance. Minimum downtime ... because of fast fault removal and program corrections as well as repair measures according to good professional practive. Less operator errors ... because of extensive knowledge. Optimum robot integration ... in the work cell because of profound knowledge of the interfaces. Motivated staff ... understanding what you do brings fun! Desired Flexibility ... understanding the robot and system functions allows fast and flexible adaptions to your special needs. We offer you a diverse training and course program for your staff from novice to expert, according to the training level, and treating the diverse application programs. These courses allow you make full use of your FANUC robot. In addition to our standard courses, we offer individual training courses on demand. In these courses, we can treat special uses, systems, and functions. Furthermore, we offer on-site courses on agreement.
Z-KAE-TRN-Roboguide-1/01
3
Contents Contents ......................................................................................................... 4 System requirements..................................................................................... 8 Installation ...................................................................................................... 8 Registration .................................................................................................... 9 Registration Step 1 .....................................................................................................................9
Registration .................................................................................................. 10 Registration Step 2 ...................................................................................................................10
License transfer ........................................................................................... 11 General ....................................................................................................................................11 Procedure.................................................................................................................................11
License transfer ........................................................................................... 12 Procedure.................................................................................................................................12
Directory structure....................................................................................... 12 Directory structure....................................................................................... 13 Generate a new cell...................................................................................... 14 Generate a new cell..................................................................................................................15 Generate a new cell..................................................................................................................16 Generate a new cell..................................................................................................................17 Generate a new cell..................................................................................................................18
Mouse commands........................................................................................ 19 Functions of the triad .................................................................................. 20 Add a tool...................................................................................................... 21 Add a tool (Option 1).................................................................................................................22 Add a tool (Option 1).................................................................................................................23 Add a tool (Option 1).................................................................................................................24 Add a tool (Option 1).................................................................................................................25 Add a tool (Option 2).................................................................................................................26 Add a tool (Option 2).................................................................................................................27 Create a tool.........................................................................................................................27
Indicate TCP (Tool Center Point) ................................................................ 28 Add a positioner (fixture)............................................................................. 29 General ....................................................................................................................................29
Add a positioner (fixture)............................................................................. 30 Insert ........................................................................................................................................30
Add obstacles............................................................................................... 31 General ....................................................................................................................................31
Add obstacles............................................................................................... 32 Add a fence ..............................................................................................................................32
View of the created work cell ...................................................................... 33 Insert and remove the yellow position lines .............................................. 34 Change the background color .................................................................... 35
Z-KAE-TRN-Roboguide-1/01
4
Explanation of icons .................................................................................... 36 Explanation of icons .................................................................................... 37 Explanation of icons .................................................................................... 38 The Run Panel .........................................................................................................................38
Explanation of icons .................................................................................... 39 Check the reachability with a mouse click (Option 1)............................... 40 Check the reachability with a mouse click (Option 2)............................... 41 Check the reachability (Option 3) ............................................................... 42 Set a user frame ........................................................................................... 43 The teach pendant ....................................................................................... 44 Create programs on the teach pendant ..................................................... 45 Create programs in the cell browser .......................................................... 46 Create a simulator program ......................................................................................................46
Start programs ............................................................................................. 47 Start programs from the teach pendant .....................................................................................47
Start programs ............................................................................................. 48 Start programs from the Run Panel...........................................................................................48 Record AVI ...............................................................................................................................48
Measuring tool.............................................................................................. 49 Measuring tool.............................................................................................. 50 Record dimensions ...................................................................................................................50 Specifiy measuring points .........................................................................................................50
Measuring tool.............................................................................................. 51 Define and change the distance between two components .......................................................51
Measuring tool.............................................................................................. 52 Define dimensioning lines .........................................................................................................52
Add parts ...................................................................................................... 53 Add a part.................................................................................................................................53
Add parts ..................................................................................................... 54 Shift parts .................................................................................................................................54 Change part properties .............................................................................................................54
Add parts ...................................................................................................... 55 Link a part with a positioner ......................................................................................................55
Add parts ...................................................................................................... 56 1. Prepare a part for a pick-and-place simulation.......................................................................56
Add parts ...................................................................................................... 57 2. Prepare a part for a pick-and-place simulation.......................................................................57
Add parts ...................................................................................................... 58 3. Prepare a part for a pick-and-place simulation.......................................................................58
Add parts ...................................................................................................... 59 4. Prepare a part for a pick-and-place simulation.......................................................................59
Parts .............................................................................................................. 60 1. Prepare a program for a pick-and-place simulation................................................................60 Z-KAE-TRN-Roboguide-1/01
5
Parts .............................................................................................................. 61 2. Prepare a program for a pick-and-place simulation................................................................61
Parts .............................................................................................................. 62 3.
Prepare a program for a pick-and-drop simulation ............................................................62
Parts .............................................................................................................. 63 4.
Create a pick program (simulator program).......................................................................63
Parts .............................................................................................................. 64 5.
Create a pick program (simulator program).......................................................................64
Parts .............................................................................................................. 65 6.
Create a drop program (simulator program) ......................................................................65
Parts .............................................................................................................. 66 7.
Create a drop program (simulator program) ......................................................................66
Parts .............................................................................................................. 67 8.
Complete a simulator program..........................................................................................67
Parts .............................................................................................................. 68 9.
Other options to create a simulator program .....................................................................68
Machines....................................................................................................... 69 General ....................................................................................................................................69
Machines....................................................................................................... 70 1. Create a machine (actuated via DO) .....................................................................................70
Machines....................................................................................................... 71 2. Create a machine (actuated via DO) .....................................................................................71
Machines....................................................................................................... 72 3. Create a machine (actuated via DO) .....................................................................................72
Machines....................................................................................................... 73 1.
Create a machine (actuated via servo) .............................................................................73
Machines....................................................................................................... 74 2.
Create a machine (actuated via servo) .............................................................................74
Machines....................................................................................................... 75 3.
Create a machine (actuated via servo) .............................................................................75
Machines....................................................................................................... 76 4.
Create a machine (actuated via servo) .............................................................................76
Machines....................................................................................................... 77 5.
Create a machine (actuated via servo) .............................................................................77
Machines....................................................................................................... 78 6.
Create a machine (actuated via servo) .............................................................................78
Machines....................................................................................................... 79 7.
Create a machine (actuated via servo) .............................................................................79
Replace the robot in an existing work cell................................................. 80 Add a second robot ..................................................................................... 81 Generate a path (Automatic program generation) .................................... 82 General ....................................................................................................................................82
Generate a path (Automatic program generation) .................................... 83 Procedure for path generation related to an edge......................................................................83
Z-KAE-TRN-Roboguide-1/01
6
Generate a path (Automatic program generation) .................................... 84 Procedure for path generation related to an edge......................................................................84 Change the approach and return position .............................................................................84
Generate a path (Automatic program generation) .................................... 85 Procedure for path generation related to an edge......................................................................85 1. Other setting options (feature) ..........................................................................................85
Generate a path (Automatic program generation) .................................... 86 Procedure for path generation related to an edge......................................................................86 2. Other setting options (feature) ..........................................................................................86
Generate a path (Automatic program generation) .................................... 87 Procedure for path generation related to an edge......................................................................87 3. Other setting options (feature) ......................................................................................87
Generate a path (Automatic program generation) .................................... 88 Segmentation ...........................................................................................................................88
Target points ................................................................................................ 89 Define target points as points in space......................................................................................89
Target points ................................................................................................ 90 1. Define a target group ............................................................................................................90
Target points ................................................................................................ 91 2. Define a target group ............................................................................................................91
Target points ................................................................................................ 92 3. Define a target group ............................................................................................................92
Target points ................................................................................................ 93 Define target points on a surface and assign a positioner..........................................................93 General ................................................................................................................................93 1. Procedure.........................................................................................................................93
Create a dynamic tool.................................................................................. 94 General ....................................................................................................................................94 Procedure.................................................................................................................................94
New functions as from V.6.40 Rev. C ......................................................... 95 Projects ....................................................................................................................................95
Z-KAE-TRN-Roboguide-1/01
7
System requirements Windows XP 1024 MB RAM Pentium 4 > 3.0 GHz Nvidia Quadro 4 oder Nvidia Quadro FX
Installation 1. Start License Checker Setup. 2. Start SimPro Setup. During the installation, you can select the language under Custom (1). You can choose between German and Japanese (2). If you select Typical, the software will be installed with German menus (please observe note). If you select Typical, you have to select the virtual controller you want to use. If you select German, the menus will be in German language. If you select Japanese, the menus will be in English. Note: If you select German or Typical, nearly all (but not all) terms and menus are in German. This manual uses the German menus. After the installation, you can use Roboguide for 30 days. After 30 days, you have to register the software. (see registration) Please note: You get the registration key after approx. 3 days. 1
Z-KAE-TRN-Roboguide-1/01
2
8
Registration Registration Step 1 Open the License Manager.
Generate a screen shot.
Beispiel Darstellung
Copy the software codes 1 and 2 from RTL-SIMPRO640. Send the screen shot and the software codes 1 and 2 to the following e-mail address:
[email protected]
Z-KAE-TRN-Roboguide-1/01
9
Registration Registration Step 2 After receiving registration key 1 and 2, follow this procedure: Open the License Manager and mark the check box (1). Enter the two keys in the appropriate columns (2). Click on Register (3).
2
1
Beispiel Darstellung
Z-KAE-TRN-Roboguide-1/01
3
10
License transfer General Roboguide has been successfully installed on computer 1. You want to transfer the license to another computer (computer 2).
1
2
Procedure Install Roboguide on computer 2. Connect the storage medium (e.g. USB stick) to computer 2. Open the License Manager on computer 2 and choose the Transfer Licenses tab. Select the USB stick using the Browse button. Click on the Prepare button. The USB stick is ready for a license transfer.
Z-KAE-TRN-Roboguide-1/01
11
License transfer Procedure Open the License Manager on computer 1 and choose the Transfer Licenses tab. Connect the storage medium (e.g. USB stick) to computer 1. Click on the button (1) and follow the instructions (2).
1
2
Open the License Manager on computer 2 and choose the Transfer Licenses tab. Connect the storage medium (e.g. USB stick) to computer 2. Click on the button (3) and follow the instructions (4). 3
4
Z-KAE-TRN-Roboguide-1/01
12
Directory structure Roboguide may be installed under Programme > Fanuc > Pro > SimPro. All data generated in one cell are recorded under C:\Dokumente und Einstellungen\ IHR Profil \ My Workcells. You can open the folder directly under Tools .
Imported IGES data are converted by Roboguide and then get the extension .CSB
Z-KAE-TRN-Roboguide-1/01
13
Generate a new cell 1. Start the software.
2. Generate a new cell.
2
3. Enter the project name and then click on NEXT.
Z-KAE-TRN-Roboguide-1/01
14
Generate a new cell 4. Select an option under Robot Selection Method . a) Create a new robot: Generate a completely new robot. b) Create a robot from a file backup: You can create a robot from an existing data recording (All of above). c) Create an exact copy of an existing robot: A sort of cloning the robot, not a copy of the complete cell, but only of the robot configuration.
a
b
c
This manual describes the procedure (a). 5. After the selection, click on the Next button. 6. Select the application software FANUC Handling Tool and then click on the Next button.
Z-KAE-TRN-Roboguide-1/01
15
Generate a new cell 7. Select the robot type and then click on the Next button.
8. Select the robot software (deviations from the display may occur), and then click on the Next button.
Z-KAE-TRN-Roboguide-1/01
16
Generate a new cell 9. You can create new groups with Additional Motion Groups . If you do not want to use additional groups, click on the Next button.
10. Here, you can select software options. Click on the Next button to open the Summary, an overview of your selection. To complete your selection, click on the Finish button.
Z-KAE-TRN-Roboguide-1/01
17
Generate a new cell Your cell has been generated after diverse messages.
Z-KAE-TRN-Roboguide-1/01
18
Mouse commands To display the mouse commands, click on this icon.
The following overview is displayed.
Overview of the functions Click on the right mouse button to rotate the layout.
Turn the mouse wheel to zoom-in/out on the cursor position
Press both buttons to zoom.
Press the wheel to shift the layout
Z-KAE-TRN-Roboguide-1/01
19
Functions of the triad You can place or shift objects via changing the properties or via the triad.
You can shift (x, y, z) and rotate (w, p, r) objects via the triad. 1. Shifting Select the desired coordinate axis with the mouse and drag. Z
X
X
2. Rotating Hold down the shift key and select the desired coordinate axis and rotate.
Z-KAE-TRN-Roboguide-1/01
20
Add a tool 1. Click on this icon to open the cell browser.
2. Open the path as follows.
Z-KAE-TRN-Roboguide-1/01
21
Add a tool (Option 1) Double-click on UT:1 (EOAT1) to open the Properties. (EOAT = End of Arm Tool)
1 2
Give a name to your tool (1). Import (2) a tool from the data base (Image Library), open the EOAT folder, select Grippers and then Vacuum01.IGS.
Z-KAE-TRN-Roboguide-1/01
22
Add a tool (Option 1) The path has been read in (1), click on Aktiviere.
1
The tool was adapted to the robot.
Z-KAE-TRN-Roboguide-1/01
23
Add a tool (Option 1) Note: For a faultless adaptation of the tool, you have to set the origin and the coordinates in a 3D CAD system. Tools may only be imported in the IGES format. Actual condition
Desired condition
+Z
Z-KAE-TRN-Roboguide-1/01
+Z
24
Add a tool (Option 1) You can place the tool at its correct position by entering changes on the property screen.
1
Mark the Sperre alle Koordinatenwerte check box (1).
Z-KAE-TRN-Roboguide-1/01
25
Add a tool (Option 2) Click on UT:1 with the right mouse button to add a link. You can choose from o CAD Bibliothek: Import from data base o CAD File: Import customer data in IGES o Create customized tools with Box, Cylinder, Sphere
The following tool is created below.
Z-KAE-TRN-Roboguide-1/01
26
Add a tool (Option 2) Create a tool 1
2
3
4
5
Z-KAE-TRN-Roboguide-1/01
27
Indicate TCP (Tool Center Point)
Open the Property window Select the UTOOL tab Check the Bearbeite UTOOL box Drag the triad with the mouse to the desired position or enter the data directly. Click on Benutze aktuelle Triad Position Click on the Aktiviere button
Z-KAE-TRN-Roboguide-1/01
28
Add a positioner (fixture) General Positioners recorded in the data base may be Conveyor belts (Conveyer) FANUC machines (Maschine) Miscellaneous (Misc) Motors (Motors) Pallets (Pallets) Racks (Racks, Shelf) Tables (Table) Furthermore, a positioner may be imported as IGES or may be created from scratch. A positioner is used for placing parts.
Z-KAE-TRN-Roboguide-1/01
29
Add a positioner (fixture) Insert Example for inserting a conveyor belt from the data base Click with the right mouse button on Positionierung and select Zufügen Positionierer and then CAD Bibliothek . Open the Conveyer path and select Conveyer11.iges . Click on the OK button.
For this representation, no bitmap file has been created. However, the model exists.
After the conveyor belt has been placed, you can position it by means of the triad or a direct entry at the target position. It is recommended to give the positioner a new name. You can copy and paste the positioner and other objects with the known Windows commands. Copying is performed in the cell browser.
Z-KAE-TRN-Roboguide-1/01
30
Add obstacles General An obstacle recorded in the data base may be a controller a fence Furthermore, an obstacle may be imported as IGES or may be created from scratch.
Z-KAE-TRN-Roboguide-1/01
31
Add obstacles Add a fence Click with the right mouse button on Hindernis and select Zufügen Hindernis and then CAD Bibliothek . Open the FENCE path and select Sreen-Course-Wire.igs . Click on the OK button.
After the fence has been placed, you can position it by means of the triad or a direct entry at the target position. Renaming is recommended. You can copy and paste the fence, as well as other objects, by using the known Windows commands. Copying is performed in the cell browser.
Z-KAE-TRN-Roboguide-1/01
32
View of the created work cell
Tool with TCP
Positioner Conveyor belt
Obstacle Fence
Z-KAE-TRN-Roboguide-1/01
33
Insert and remove the yellow position lines You can insert and remove the position lines (1). Select the cell properties in the cell browser (double-click on icon (2)). Select the Chui Welt tab. Uncheck the Zeige Positionslinien check box (3).
2
3
1
Z-KAE-TRN-Roboguide-1/01
34
Change the background color Click on Tool and select Optionen . Select the Farben tab. You can change the background color in this window.
Z-KAE-TRN-Roboguide-1/01
35
Explanation of icons New cell
Help
Open a cell *Process Navigator Save a cell Undo Open the cell browser Use the process navigator for a step-by-step work cell creation.
Select to directly approach a
Display teach tool (TCP)
- Face - Edge - Vertex
To set target points, e.g. point in space.
Move to retry To reach positions that are out of reach by using another axis configuration.
Display speed controller
Display motion coordinates
Z-KAE-TRN-Roboguide-1/01
36
Explanation of icons Call alarm screen
Graphics mode (may be applied only in connection with parts)
Call web server
Open/close tool (may be applied only in simulator programs or with dynamic tools)
Start AVI recording
Use teach pendant
Display robot work cell
Cycle start
*Open Run Panel See next page
Error Reset
Pause Cancel
Z-KAE-TRN-Roboguide-1/01
37
Explanation of icons The Run Panel In the Run Panel, you can select settings for the AVI recording as well as for the automatic mode.
*Open Run Panel
2
1 Kollisionserkennung: Enables the collision detection Sammle TCP: TCP motion path is displayed (1) Geteachte Bahn sichtbar: The taught path is displayed (2) Fenster ausblenden: You can display or hide the Run Panel window Anzeige erneuern: Must be enabled Komprimiere AVI: Must be enabled Simulationszeit auf AVI: The AVI time may be displayed in the AVI
Z-KAE-TRN-Roboguide-1/01
38
Explanation of icons
Zoom
Center selected object
Measuring tool
Mouse commands
Change view
Orthogonal views
Z-KAE-TRN-Roboguide-1/01
Grid representation
39
Check the reachability with a mouse click (Option 1) Press and hold down the SHIFT + CTRL keys on your computer keyboard. Place the cursor and click at a point (a small line shows the Z direction) where the robot is to move. The TCP (green) jumps to this point and the robot follows. If the color of the TCP changes to red this position is not within reach.
Reachable (green TCP)
Z-KAE-TRN-Roboguide-1/01
Not reachable (red TCP)
40
Check the reachability with a mouse click (Option 2) 2
Open the Quickbar (1) with the according icon (2). With a mouth click, select a point where the robot is to move. Face: Face Edge: Edge Vertex: Vertex (corner point) Arc Ctr.: Center point (can be used only under certain conditions) Place the cursor and click on a point (a small line shows the Z direction) where the robot is to move.
1
The TCP (green) jumps to this point and the robot follows. If the color of the TCP changes to red this position is not within reach.
Face
Z-KAE-TRN-Roboguide-1/01
Edge
Vertex
41
Check the reachability (Option 3) The robot may be moved via the triad and the mouse. Enable the icon. Drag the triad with the mouse to the desired position. The robot follows the TCP.
Z-KAE-TRN-Roboguide-1/01
42
Set a user frame Figure 1 1 Move the robot TCP to a vertex of the conveyor belt (Figure 1). Open the path, as shown in Figure 2. Check the Bearbeite UFrame check box (1). Click on Use Current TCP Location (2). The user frame (3) is displayed and may be positioned via the triad or by means of direct entry. Click on the Aktiviere button and then on OK . Figure 2
1
2
3
Z-KAE-TRN-Roboguide-1/01
43
The teach pendant You can use all functions of the teach pendant.
Use teach pendant
Bei der Version V 6.40 (Rev B) kann das i-Pendant in Verbindung mit der Applikations-Software FANUC Handling Tool nicht genutzt werden. Wenn Sie mit dem iPendant arbeiten wollen, müssen Sie die ApplikationsSoftware Handling Tool (N.A.) benutzen
Display current position or enter current position. Use MoveTo to approach current position.
Z-KAE-TRN-Roboguide-1/01
Data backup path
44
Create programs on the teach pendant On the teach pendant, you can create virtual reality programs. In addition, the programs are displayed in the cell browser.
Z-KAE-TRN-Roboguide-1/01
45
Create programs in the cell browser You can choose between two methods to create a program in the cell browser. 1. Simulator Program 2. Teach Pendant Program (TP)
1
(Known procedure)
2
Create a simulator program
Select Simulationsprogramm zufügen . Give a name to your program (1). Select the Simulation subtype (2). Click on the Aktiviere button and then on OK . The window (3) is still visible. 3 In the Record menu, you can teach positions. In the Inst menu, you can insert Wait/Call and Remark (Pickup and Drop will be explained later.) Use FWD and BWD to start the programs. Convert your simulator program into a TP program.
4
Open the properties of the program (5). Select the None (TP) subtype. The program is displayed on the select screen on the teach pendant.
5
Z-KAE-TRN-Roboguide-1/01
46
Start programs You can start programs from the teach pendant or the Run Panel.
Start programs from the teach pendant
1
(Known procedure) In the Ansicht menu, you can select the following items (2).
2
You can change the positions by means of the triad and the mouse. Click on the triad. If the triad is displayed as in Figure 3, you can change the positions. This change is immediately updated in the program.
Figure 3
Z-KAE-TRN-Roboguide-1/01
47
Start programs Start programs from the Run Panel Select the program in the cell browser (no double-click). Open the Run Panel (1) and enable the desired settings. Start the program (2).
1
If Sammle TCP has been enabled, the movement of the TCP is recorded (3). If you want to remove the connecting lines (4), disable the appropriate function in the Ansicht menu (see Start programs from the teach pendant). 1
Record AVI Use the record button to create an AVI file. After the AVI file has been created, the storage path is displayed. In case of not registered versions (30-day demo) a message appears to report that this version has not been registered. Note: If you have enabled the Starte Programm in Schleife function, you have to end the AVI recording with the Cancel button.
4
Z-KAE-TRN-Roboguide-1/01
3
48
Measuring tool This example explains how to measure the width of the conveyor belt. Open the measuring tool (1). Click on the Von button (2).
1 2
4
This button has been enabled
Place the cursor on the vertex (3). Click on the Nach button (4). Place the cursor on the opposite vertex (5). 3
5
or
Z-KAE-TRN-Roboguide-1/01
49
Measuring tool Record dimensions Use the button (1) to record dimensions in the cell browser. Thus, you can display these dimensions at any time. 1
Specifiy measuring points Use the button (2) to specify the starting and end point of the measurement. Entity: The selected point Ursprung: From the origin If a measurement starts from the robot, you have these additional choices, see Figure 3.
Z-KAE-TRN-Roboguide-1/01
3
2
Figure 3
50
Measuring tool Define and change the distance between two components Generate a layout with two boxes. Measure from origin to origin. Record the dimensions in the cell browser. Open the recorded dimensions in the cell browser. Enter a number in the X/Y/Z or D box to position the objects.
Z-KAE-TRN-Roboguide-1/01
51
Measuring tool Define dimensioning lines
Select the Extrusion tab. Click on the mm value of the X measurement and drag the dimensioning line in position. Click on the OK button. Open the window again. An X should now be displayed in the Extrusion window. Select the X and change the position of the dimensioning line in the Erweitern (L) and the Winkel boxes.
Z-KAE-TRN-Roboguide-1/01
52
Add parts The following simulations are possible with a part: 1. You can move parts. 2. You can draw on parts (path generation, see Path generation ).
Add a part Open the cell browser. Click on Teile with the right mouse button. Add a part (BOX). The part properties will be displayed (1). The part has been placed (2). 1
2
Z-KAE-TRN-Roboguide-1/01
53
Add parts Shift parts Click on the base plate of the part (1). Shift the part by means of the triad to a position in the layout, so that it 2 will not be visible in an AVI recording or a screen shot. Regard this position as a pseudo-storage location.
1
Change part properties In the Property window, you can change names, colors, dimensions, and the weight.
Z-KAE-TRN-Roboguide-1/01
54
Add parts Link a part with a positioner Double-click on the conveyor belt to open the Properties window. Select the Teile tab. Check the check box of the desired part (1). Click on the Aktiviere button.
1
The origins of the part and the conveyor belt will be linked (2). Check the Bearbeite Teile Offset check box (3). Position the part by means of the triad or direct entry (4). 2
In order to complete the procedure, click on Ativiere and then on OK (5).
3
4
5 Z-KAE-TRN-Roboguide-1/01
55
Add parts 1. Prepare a part for a pick-and-place simulation By means of a simulator program, you can pick and place parts. The description below explains the necessary settings step-by-step. Create a work cell as displayed in the figure below. Tool mit TCP
1
Positioner 1 Conveyor belt Link part with conveyor belt and position
Positioner 2 Table
In this simulation, the robot is to pick the part (1) from the conveyor belt and place it on the table.
Z-KAE-TRN-Roboguide-1/01
56
Add parts 2. Prepare a part for a pick-and-place simulation Link the part with the table. Position the part at the target position.
Z-KAE-TRN-Roboguide-1/01
57
Add parts 3. Prepare a part for a pick-and-place simulation Link the part with the tool. Position the part at the target position (where is the part to be positioned at the tool). Be sure to use the correct link. In case the tool was created by yourself, use the same LINK as shown in Figure 1.
Z-KAE-TRN-Roboguide-1/01
58
Add parts 4. Prepare a part for a pick-and-place simulation This is how your work cell should look like.
When you click on the icon (1), the part at the tool should be removed or inserted.
1
Z-KAE-TRN-Roboguide-1/01
59
Parts 1. Prepare a program for a pick-and-place simulation Create a teach pendant program using the positions necessary for such a sequence. The pick-and-place operations will be included later.
Ahead Table
Start
Ahead Belt Pick Belt
Z-KAE-TRN-Roboguide-1/01
Place Table
60
Parts 2. Prepare a program for a pick-and-place simulation Insert blank lines (see figure). These lines will be needed for the pick-and-place operations.
Z-KAE-TRN-Roboguide-1/01
61
Parts 3. Prepare a program for a pick-and-drop simulation Before you can complete the programs, you have to make some adjustments to the properties (tool, conveyor, and table). Make the following adjustments: Tool adjustments
Z-KAE-TRN-Roboguide-1/01
Table adjustments
Conveyor adjustments
62
Parts 4. Create a pick program (simulator program) Open the Programme path. Click on the item Simulationsprogramm zufügen with the right mouse button. You will see Figure 3. Name your program (1) Pick and click on the Aktiviere button and then on OK .
Figure 3
1
Figure 4
Z-KAE-TRN-Roboguide-1/01
63
Parts 5. Create a pick program (simulator program) Select Inst > Pickup. You will see Figure 2.
Figure 2
Set the following items.
Close the window and store the program with the following procedure.
Z-KAE-TRN-Roboguide-1/01
64
Parts 6. Create a drop program (simulator program)
Open the Programme path. Click on the item Simulationsprogramm zufügen with the right mouse button. You will see Figure 3. Name your program (1) Drop and click on the Aktiviere button and then on OK .
Figure 3
1
Figure 4
Z-KAE-TRN-Roboguide-1/01
65
Parts 7. Create a drop program (simulator program)
Select Inst > Drop. You will see Figure 2.
Figure 2
Set the following items.
Close the window and store the program with the following procedure.
Z-KAE-TRN-Roboguide-1/01
66
Parts 8. Complete a simulator program To edit your sequence program, use the following procedure.
Start your sequence program in the Run Panel (program must be stored in cell browser).
Z-KAE-TRN-Roboguide-1/01
67
Parts 9. Other options to create a simulator program You can insert and remove parts by means of the pick-and-drop programs at any time. In order to do so, you have to create the following simulator programs. If you create and call this program, the part on the conveyor belt will be positioned.
If you create and call this program, the part on the table will be removed from the layout.
Z-KAE-TRN-Roboguide-1/01
68
Machines General If you create a machine, you can make components movable. Examples: The door of a machine is to be opened and closed. A conveyor belt is to move. A press is to be opened and closed. Etc. There are two methods to open and close a door: Using a digital output (DO) Using a servo motor
Movements must comply with the following rule: Rotational and linear movements have to be executed around or in z direction respectively.
Z-KAE-TRN-Roboguide-1/01
69
Machines 1. Create a machine (actuated via DO) In this example, you have to create a machine in the form of a simplified conveyor belt. The movement is to be actuated via a digital output. Remove the existing conveyor belt from your simulator work cell (properties). Add a box with the following dimensions (1) and place the box in front of the robot. Rename the box. The new name should be Grundelement (2).
2
1
Z-KAE-TRN-Roboguide-1/01
70
Machines 2. Create a machine (actuated via DO) Click with the right mouse button on Grundelement and select Link zufügen and then Box . The box has been placed (1). Rename the box. New name: Schlitten (2). Click on the button (3) (the motor orientation will be displayed as a triad). 2
Orient the triad as described below. For W set 90 or -90. The triad is repositioned. Click on the button (4). Select the Link CAD tab.
1
3
4
Z-KAE-TRN-Roboguide-1/01
71
Machines 3. Create a machine (actuated via DO) Position the slide (Schlitten) by means of the triad or direct entry (2). Change the color of the slide. Select the Motion tab. 2
Make the settings according to figure 3. Adjust the time value (3). The number (4) specifies the distance. Set the outputs in the TP program in order to make the slide move.
1 Fig. 3 3
4
Z-KAE-TRN-Roboguide-1/01
72
Machines 1. Create a machine (actuated via servo) The layout is identical with the layout for the machine actuated via DO. Except for the type of actuation and the configuration of the additional axis. Create a new robot work cell and make the following selections:
Z-KAE-TRN-Roboguide-1/01
73
Machines 2. Create a machine (actuated via servo) Configure the additional axes as shown below: 1
2
3
4
5
6
Z-KAE-TRN-Roboguide-1/01
74
Machines 3. Create a machine (actuated via servo) 7
8
9
10
11
12
Z-KAE-TRN-Roboguide-1/01
75
Machines 4. Create a machine (actuated via servo) 13
14
15
16
17
18
Z-KAE-TRN-Roboguide-1/01
76
Machines 5. Create a machine (actuated via servo) 19
20
The work cell has been created.
Z-KAE-TRN-Roboguide-1/01
77
Machines 6. Create a machine (actuated via servo) Create the basic element (Grundelement) of the machine
Create the link Schlitten (slide).
Z-KAE-TRN-Roboguide-1/01
78
Machines 7. Create a machine (actuated via servo) Select (1) and position the slide by means of the triad or by direct entry as shown below. 1
Select the Motion tab and make the following settings.
To complete the procedure, click on Aktiviere and then on OK . You can now use the additional axis in your programs.
Z-KAE-TRN-Roboguide-1/01
79
Replace the robot in an existing work cell 1
Open the robot properties and click on the button (1). Select the desired robot type in the wizard. Click on the Aktiviere button. The new robot type is read in. All data, except for the TP programs are restored. However, you can copy (2) and paste (3) the TP programs. After the copy-and-paste procedure, you can load the programs on the teach pendant. The programs do not have to be re-taught.
2
3
Z-KAE-TRN-Roboguide-1/01
80
Add a second robot You can add a second robot to an existing layout. The number of robots that may be added is limitless. Use the wizard to configure the second robot.
Teaching is possible for both robots. Make sure on the teach pendant display (2) that the correct robot is activated. If the wrong robot is activated, keep the teach pendant activated and click on the desired robot. 2
Z-KAE-TRN-Roboguide-1/01
81
Generate a path (Automatic program generation) 1
General Use the graphics function (1) to generate a path (program) automatically. You can use the graphics function only in connection with parts. You can choose between the following options: Edge line (2) Freehand line (3) Surface fit line (projection on surface) (4) Curve (5) 3
2
2 3 4 5
4
Z-KAE-TRN-Roboguide-1/01
5
82
Generate a path (Automatic program generation) Procedure for path generation related to an edge
Select the part (single mouse click). Open the graphics icon menu. Click on the edge line symbol (Kantenlinie). Move the mouse cursor along the edge. The distance is displayed e.g. 78.1 mm). Use a double-click to complete the selection of the desired section. The window (1) is displayed. Name the program (2). Check the settings (3). Click on the button (4). You have created a program with an approach and a return position. A feature and a segment have been created in the cell browser (5). Segments may be segmented.
2
1
3
5 4
Z-KAE-TRN-Roboguide-1/01
83
Generate a path (Automatic program generation) Procedure for path generation related to an edge Change the approach and return position
1
You can modify the approach and return position when opening the Näherung/Rückzug tab (1). When you do not wish to use an approach or return position, you can disable these functions.
After such modifications, you have to regenerate the program. The old version will be overwritten (3).
2
3
Z-KAE-TRN-Roboguide-1/01
84
Generate a path (Automatic program generation) Procedure for path generation related to an edge 1
1. Other setting options (feature)
Program settings (1) (self-explaining)
Position standards (2) This setting specifies the tool orientation for the path generation.
2
TCP
Z-KAE-TRN-Roboguide-1/01
85
Generate a path (Automatic program generation) Procedure for path generation related to an edge 2. Other setting options (feature)
1
On the Raw Normals tab (1), you can define the start and end angle position. In this example, the start angle position is 30 degrees and the angle position at the end of the path is -30 degrees.
Z-KAE-TRN-Roboguide-1/01
86
Generate a path (Automatic program generation) Procedure for path generation related to an edge
3. Other setting options (feature)
1
On the Pos Offsets tab (1), you can specify the following settings. 2 2. Translation relative to the standard position
3. Translation relative to the segment
3 2 4 2 5 2 6 2
4. Offset in Z 5. Offset in X 6. Offset in Y 7. 8. 7 9. 10. Rotation around Z 11. Rotation around X 12. Rotation around Y
8 9 10 12
13. 14.
11
13 14
Z-KAE-TRN-Roboguide-1/01
87
Generate a path (Automatic program generation) Segmentation Generate a path (1). Open the graphics window (2) and click on Bearbeiten (3). Click on Segment1 in the cell browser. The Segment teilen button (4) is active. Click on the button (4).
1
The segment is divided (Figure 4 and 5). For segment 1 and 2, you can now specify different settings. A further segmentation is possible. After a segmentation, you can shift the segmentation points with the mouse and adjust them.
2
4
3
Figure 4
Z-KAE-TRN-Roboguide-1/01
Figure 5
88
Target points 1
Use the target points (1) to specify positions. You can choose between the following options: Define positions in space (2). Define positions on a surface (3). Define positions at the TCP (4). When you select button (2) together with button (5), the points in space are stored in a target group. You can also specify a target group separately at a later point.
2
3 4 5
Define target points as points in space Click on the Air button and specify points in space using the mouse. The target points are displayed as a coordinate system. The targets are also displayed in the cell browser. In order to create a program from these targets, you have to define a target group. For explanations, see next page.
Z-KAE-TRN-Roboguide-1/01
89
Target points 1. Define a target group Select Target Groups and then Add Target Group . Click on Abbruch (1). The target group has been established (2). Open the target group properties (3).
1
2
3
Z-KAE-TRN-Roboguide-1/01
90
Target points 2. Define a target group
Specify a program name (1). Click on the Members button (2). Assign the targets (3) to the group (4). Click on Aktiviere (5) and then on OK (6).
3
2
4
1
6
5
Z-KAE-TRN-Roboguide-1/01
91
Target points 3. Define a target group
Select a motion line (1). Select the Target Edit tab (2). You will see the screen in figure 2. You can now adapt the sequence to your needs, e.g. you can disable Approach and Retreat (3) or the interpolation (4).
Figure 2
1
2
4
3
Select the Generation Parameters tab. Click on the Erstelle Muster TP Programm button.
Z-KAE-TRN-Roboguide-1/01
92
Target points Define target points on a surface and assign a positioner General This method is used to assign target points to a positioner (e.g. a box). When shifting the box, the target points are also shifted. Of course, you can define targets on surfaces without defining interactions.
1. Procedure Use the Surface button to generate 3 points on the surface of a box. Open the properties of each target point and select the box under Attached (1). The target points are displayed in the cell browser under the box (2).
1
2
From here on, the procedure is identical with the procedure for defining points in space.
Z-KAE-TRN-Roboguide-1/01
93
Create a dynamic tool
General To create and simulate a dynamic tool, you need two different models.
Procedure Create a new work cell. Import the 36005f-200.CSB model as the tool (known procedure). Select the Simulation tab and add the 36005f-200-4.CSB model using the icon (1). Use the Öffnen/Schließen buttons (2) to check whether the gripper opens and/or closes. You can also use the symbol for this check. The opening and closing is realized in a program sequence by means of the Pick or Drop simulator programs (see Parts). Note The parts that are to be moved have to be defined on the Teile and Simulation tabs (3).
3
1
2
Z-KAE-TRN-Roboguide-1/01
94
New functions as from V.6.40 Rev. C Projects
Z-KAE-TRN-Roboguide-1/01
95
