RET54_tob_755543_ENe

Transformer Terminal Product Guide

RET 541, RET 543, RET 545

Transformer Terminal

RET 541, RET 543, RET 545 1MRS755543 Issued: February 2005 Status: Updated Version: E/26.10.2010 Data subject to change without notice

Features

• Transforme Transformerr termin terminal al for for protection, protection, control, control, measurement and supervision of two-winding power transformers and generatortransformer blocks in distribution networks • Designed Designed to withstand withstand harsh environmen environments ts e.g. in heavy industry, marine and offshore applications • Three-phas Three-phase e current current differential differential protection protection with stabilized and instantaneous stages for fast and selective winding short-circuit and interturn fault protection as main protection • Fast Fast and relia reliable ble opera operatio tion n even even with with satusaturating CTs • Numeri Numerical cal imple implemen mentat tation ion of vecto vectorr group matching allows wye-connection of measuring CTs as standard without interposing CTs, irrespective of transformer vector  group • Restricte Restricted d earthearth-fault fault protection protection with the conventional high impedance principle or  the stabilized numerical principle • ThreeThree-pha phase se overcu overcurre rrent nt and earth-f earth-faul aultt back-up protection with definite time and IDMT characteristics for both windings

• Option Optional al automat automatic ic on-loa on-load d tap-cha tap-change nger  r  control function for single or parallel transformers using the Master-Follower, Negative Reactance or Minimizing Circulating Current principles • Supports Supports several several methods methods to interf interface ace tapchanger position information to differential protection and voltage regulator  • Measur Measureme ement nt of two two sets sets of threethree-pha phase se currents, phase-to-phase or phase to neutral voltages, neutral current, residual voltage, frequency, power factor, active and reactive power and energy • Conditi Condition on monito monitorin ring g includi including ng circui circuittbreaker condition monitoring, trip circuit supervision and internal self-supervision of  the transformer terminal • Extensive Extensive set of integrated integrated communica communication tion protocols: SPA, LON, IEC 60870-5-103, Modbus RTU/ASCII, DNP 3.0 • Interf Interface ace to to Profib Profibus us DP DP and IEC IEC 61850 61850 based systems via adapters • Part Part of ABB’s ABB’s subst substati ation on automa automatio tion n syssystem

• Therm Thermal al overl overload oad and and negat negative ive phas phase e sequence protection • Additional Additional protection protection functions functions available available in the Multi –version terminal: overexcitation, overvoltage, undervoltage, residual overvoltage, directional overcurrent and earthfault, overfrequency, underfrequency and underimpedance line back-up protection • Large Large graphi graphic c displa display, y, either either integ integrat rated ed or  as an external module • Contro Controll functio functions ns inclu includin ding g local local and remote control of switching objects, including object status indication and interlockings on bay and substation level

ret54_mimic_co180dpi

Fig. Fig. 1

Mimi Mimic c view view of of RET RET 54_ 54_ tran transf sfor orme merr term termiinal.

3

Transformer Terminal

RET 541, RET 543, RET 545 1MRS755543

Application

The RET 541/543/545 transformer terminals are designed to be used for the protection, control, measurement and supervision of twowinding power transformers and generatortransformer blocks in distribution networks. RET 54_ terminals can also be used in harsh environments e.g. in heavy industry, marine and offshore applications. The main protection function is three-phase current differential protection with stabilized and instantaneous stages for fast and selective winding short-circuit and interturn protection. Besides 2nd and 5th harmonic restraints, the stabilized stage also includes a waveform recognition-based blocking-deblocking feature. Reliable operation even with partially saturated current transformers, that is, short operate times at faults occurring in the zone to be protected and high stability at external faults are achieved. Increased sensitivity can be obtained by automatic adaptation to the position changes of the on load tap changer. Interposing current transformers are not needed: Any vector group matching and CT ratio corrections in a wide range are numerically implemented as well as zero-sequence current elimination, which prevents unwanted trips at earth faults occurring outside the protected area. In addition to the differential protection, the  Basic version terminals incorporate the following protections: Restricted earth fault protection with stabilized numerical or high impedance principle, unbalance and thermal overload protections, three phase overcurrent and non-directional earth fault back-up protection with definite and IDMT characteristics on both sides of the transformer. The  Multi-version terminals, further including overvoltage and undervoltage, residual overvoltage, underfrequency and overfrequency, overexcitation, directional earthfault, directional overcurrent and underimpedance line back-up protections fulfill the most demanding application requirements. Enhanced with the optional automatic voltage regulation function, the RET 54_ terminal can be applied as a comprehensive integrated transformer management terminal. The voltage regulator can be applied for a single transformer or for parallel transformers with Master-Follower, Negative Reactance or  Minimizing Circulating Current principles. A special control version terminal with voltage regulator and control functions can be applied, when integration of voltage regulation and protection is not allowed.

4

The graphical configuration tool, based on the IEC 61131-3 standard, enables easy creation of application-specific configurations and MIMIC pictures corresponding to different switchgear systems. The process status is shown on a dynamic large graphical display. Detailed information, for instance, measured values, events and application-specific alarms, are presented in the display views. The RET 54_ terminals can measure two sets of three phase currents, phase-to-phase or   phase-to-earth voltages, neutral current, residual voltage, frequency and power factor. Active and reactive power is calculated from the measured currents and voltages. Energy can be calculated on the basis of the measured power. The measured values can be indicated locally and remotely as scaled primary values. With the condition monitoring functions the RET 54_ transformer terminal monitors e.g. trip circuits, gas pressure of the breaker and  breaker wear and provides scheduled time intervals for maintenance. The RTD1 card, available as an option to the RET 541 and RET 543 terminals, provides versatile analog inputs enabling e.g. tap position supervision of the on load tap changer, RTD inputs for top and bottom oil temperature monitoring, and ambient temperature  biasing for accurate thermal overload protection. The mA outputs allow transfer of any measurement data e.g. to PLCs. By means of the graphic HMI display, the control functions in the transformer terminal indicate the position of disconnectors, circuit  breakers and tap changer locally. Local control of these objects is possible via the push  buttons on the front panel of the terminal. Furthermore, the terminal allows position information of the objects to be transmitted to the remote control system. Controllable objects, such as CBs, can also be opened and closed over the remote control system. Supporting a wide range of communication  protocols, including SPA, LON, IEC 608705-103, DNP 3.0 and Modbus RTU/ASCII, commonly used by utilities and industries, the terminals are flexibly integrated into different control systems. Connection to Profibus DP or IEC 61850 based system is possible via the interface adapters SPA-ZC 302 or SPA-ZC 400, respectively.

Transformer Terminal

RET 541, RET 543, RET 545 1MRS755543

Design

The transformer terminals RET 541, RET 543 and RET 545 differ from each other  regarding the number of digital inputs and outputs available. Please, refer to section “Ordering” for more details. The functions of the RET 54_ t ransformer  terminal are categorized as:

The control function blocks are documented on the CD-ROM “Technical Descriptions of  Functions” (1MRS750889-MCD) Condition monitoring functions

The condition monitoring function blocks are documented on the CD-ROM “Technical Descriptions of Functions” (1MRS750889MCD)

• protection functions • measurement functions • control functions • condition monitoring functions • communication functions • general functions • standard functions The functions are further divided to three subsets that correspond to different functionality levels, refer to section “Ordering Information” Protection functions

Protection is one of the most important functions of the RET 54_ transformer terminal. The protection function blocks (e.g.  NOC3Low) are independent of each other  and have e.g. their own setting groups and data recording. The protection function blocks are documented on the CD-ROM “Technical Descriptions of Functions” (1MRS750889-MCD) Measurement functions

The measurement function blocks are documented on the CD-ROM “Technical Descriptions of Functions” (1MRS750889-MCD) Control functions

The control functions are used to indicate the  position of switching devices, i.e. circuit  breakers and disconnectors, and to execute open and close commands for controllable switching devices in the switchgear. Furthermore, there are supplementary functions for  control logic purposes, e.g. on/off switches, MIMIC alarm, LED control, numerical data for the MIMIC and logic controlled position selection. The control functions configured using the Relay Configuration Tool can be associated with position indicators that are part of the MIMIC configuration picture displayed on the HMI. Position indicators are used to indicate the position of switching devices via the MIMIC picture and to control them locally.

General functions

Additional functions are available for different general purposes to be used in logics such as activation of HMI backlight, switchgroups, and resetting of operation indications, latched output signals, registers and disturbance recorder. Communication functions

The RET 54_ transformer terminal provides the IEC_103, Modbus, DNP 3.0, SPA and LON serial communication protocols. In a customer-specific transformer terminal configuration, special events can be generated via an EVENT230 event function. EVENT230 is documented on the CD-ROM “Technical descriptions of Functions” (1MRS750889-MCD). Standard functions

Standard functions are used for logics, such as interlocking, alarming and control sequencing. The use of logic functions is not limited and the functions can be interconnected with each other as well as with protection, measurement, power quality, control, condition monitoring and general functions. In addition, the digital inputs and outputs as well as LON inputs and outputs can be connected to standard functions by using the Relay Configuration Tool. The standard function blocks are documented on the CD-ROM “Technical descriptions of  Functions” (1MRS750889-MCD). Other functions Low auxiliary voltage indication

The RET 54_ transformer terminal is provided with a low auxiliary voltage indication feature. The power supply module issues an internal alarm signal when a drop in the  power supply voltage is detected (ACFail, active low). The alarm signal is activated if  the power supply voltage falls about 10%  below the lowest rated DC input voltage of  the power supply module.

5

Transformer Terminal

RET 541, RET 543, RET 545 1MRS755543

Design (cont´d)

The indication of a low auxiliary voltage is available in the transformer terminal configuration and can be connected to any signal out put of the RET 54_.

tion of a digital input can be inverted. The  programmable filter time removes debounces and short disturbances on a digital input. The filter time can be set for each digital input separately.

Overtemperature indication

The RET 54_ transformer terminal includes an internal temperature supervision function. The power supply module issues an internal alarm signal when overtemperature has been detected inside the terminal enclosure. The alarm signal will be activated once the tem perature inside the terminal enclosure increases to +78C (+75...+83C). Overtemperature indication is available in the transformer terminal configuration and can be connected to any signal output of the RET 54_. Analog channels

The transformer terminal measures the analog signals needed for protection, measuring, etc. via galvanically separated matching transformers. RET 54_ transformer terminals have 9 analog channels. Furthermore, the transformer terminal includes virtual analog channels for calculating the residual current and residual voltage from phase currents and voltages. Both the amplitude and the phase angle are calculated for the virtual channels.  Note! When sensitive earth-fault protection is needed, core balance transformers are not recommended to be replaced with the numerically derived sum of phase currents. Normally, an earth-fault setting below 10% of the rated value requires the use of a core balance transformer. Analog channels of the transformer terminal are configured with the CAP 505 Relay Product Engineering Tools. A separate scaling factor can be set for each analog channel. The factors enable differences between the ratings of the protected unit and those of the measuring device (CT and VT ratio corrections). The setting value 1.00 means that the rated value of the protected unit is exactly the same as that of the measuring device.

6

Some specific digital inputs can be programmed to operate either as digital inputs, as  pulse counters or as used for time synchronization. When a digital input operates as a  pulse counter, pulse counting frequency can  be up to100 Hz. Oscillation suppression

The transformer terminals have two global  parameters for the suppression of digital input oscillation. The settings of these parameters determine the oscillation level and hysteresis for all digital inputs. Event is generated in case oscillation is detected. Attributes of a digital input for transformer  terminal configuration

For each digital input, the status of the input (value), the time tag for the status change (time) and the validity of the digital input (invalidity) can be issued by the attributes. These attributes are available in the transformer terminal configuration and can be used for various purposes. RTD/analog inputs

The RET 541 and RET 543 transformer terminals equipped with an RTD/analog module (RTD1) have eight general purpose analog inputs for DC measurement. The RTD/analog inputs are galvanically isolated from the transformer terminal power supply and enclosure. However, the inputs have a common ground. The general purpose RTD/analog inputs accept voltage-, current- or resistancetype signals. For each measuring mode, a separate parameter is provided for choosing  between the available measurement ranges. RTD/analog inputs can be applied for e.g. temperature measurement. Digital outputs

The outputs of the transformer terminal are categorized as follows:

Digital inputs

• HSPO: High-speed power output, double pole contact, preferred for tripping pur poses and for circuit breaker and disconnector control

The digital inputs of the transformer terminals are voltage controlled and optically isolated with three treshold voltages defined by the order, see chapter “Ordering”. The func-

• PO: Power output, either single-pole or  double-pole contact, preferred for circuit  breaker and disconnector control

Transformer Terminal

RET 541, RET 543, RET 545 1MRS755543

• SO: Signal output, either NO (Normally Open) or NO/NC (Normally Open/Normally Closed) contact. The output contact is a normal-duty contact and cannot be used for controlling a heavy load such as a circuit breaker. Analog outputs

The RET 541 and RET 543 transformer terminals equipped with an RTD/analog module have four general purpose 0...20 mA analog current outputs. All outputs are galvanically isolated from the supply and enclosure of the transformer terminal and from each other. Analog outputs can be utilized for transferring any measured or calculated information to panel meters or e.g. PLCs. Alarm LED indicators

The transformer terminal offers eight alarm LED indicators to be configured with the Relay Mimic Editor. The LED colours (green, yellow, red), their use, and the ON and OFF state texts can be freely defined. Three basic

Display panel

The transformer terminal is provided with either a fixed display or an external display module. The external display module requires a separate voltage supply from a common source with the main unit. The display consists of 19 rows divided into two windows: a main window (17 rows) and an assisting window (2 rows). The graphic display presents detailed information on MIMIC, objects, events, measurements, control alarms, and parameters. The assisting window is used for terminal-dependent indications/alarms and help messages. Additionally, the panel includes the following HMI items: • three push-buttons for object control (I, O, object selection)

Serial communication

The transformer terminal has three serial communication ports, one on the front panel and two on the rear panel. The standard optical ABB connector 

The standard optical ABB connector (RS-232 connection) on the front panel is intended for  the connection of a PC for configuring the transformer terminal with the CAP 50_ tools. The front interface uses the SPA bus protocol.

operation modes are supported: non-latched, latched-steady and latched flashflashing. Alarms can be acknowledged remotely, locally or by using logic of the transformer  terminal. The alarm channels include time tagging for  detected alarms. The time tagging principle used depends on the operation mode. Interlocking LED indicator 

The interlocking LED indicates that control operation has been interlocked or that the interlocking is in bybass mode, e.g. when control is possible despite of interlocking. Trip Circuit Supervision

The purpose of this function is to supervise the tripping circuitry of the circuit breaker. An alarm will be generated in case a faulty tripping circuit, e.g. a circuit is not able to  perform a trip, is detected. The supervision is based on the constant-current injection through the tripping circuitry.

• eight freely programmable alarm LEDs with different colours and modes according to the configuration • LED indicator for control interlocking • three protection LED indicators • HMI push-button section with four arrow  buttons and buttons for clear and enter  • optically isolated serial communication  port • backlight and contrast control • freely programmable button (F) which can  be used in the configuration of the transformer terminal • a button for remote/local control HMI has two main levels, the user level and the technical level. The user level is for  “everyday” measurements and monitoring whereas the technical level is intended for  advanced transformer terminal programming. Unauthorized access can be prevented with  passwords.

SPA/IEC_103/DNP 3.0/Modbus communication on the rear connector X3.2

The 9-pin D-type subminiature male connector (RS-232 connection) on the rear panel connects the transformer terminal to the distribution automation system via the SPA bus, IEC_103, DNP 3.0 or Modbus. The fibreoptic interface module type RER 123 is used to connect the transformer terminal to the fibre-optic communication bus for SPA and 7

Transformer Terminal

RET 541, RET 543, RET 545 1MRS755543

IEC_103 protocols. RS-485 interface module RER 133 is used to connect the transformer  terminal to the RS-485 communication bus for DNP 3.0 and Modbus. LON/SPA bus communication on the rear  connector X3.3

The 9-pin D-type subminiature female connector (RS-485 connection) on the rear panel connects the transformer terminal to the substation automation system via the SPA bus or  the LON bus. The fibre-optic interface module type RER 103 is used to connect the transformer terminal to the fibre-optic communication bus. The RER 103 module supports  both SPA bus and LON bus communication. The SPA-ZC 302 is an interface module that  provides connectivity to the Profibus DP fieldbus and SPA-ZC 400 interface module  provides connectivity to the IEC 61850-8-1 Station bus.

Transformer  terminal configuration

The Relay Configuration Tool, based on the IEC 61131-3 standard and included in the CAP 505 Relay Product Engineering Tools, is used for configuring the basic terminal, protection and logic function blocks, control and measurement functions, timers and other  functional elements included in the logic functions category. The programmable system of RET 54_ transformer terminals allows the output contacts to  be operated in accordance with the state of  the logic inputs and the outputs of the protection, control, measurement and condition monitoring functions. The PLC functions (e.g. interlocking and alarm logic) are programmed with Boolean functions, timers, counters, comparators and flip-flops. The  program is written in a graphic function block  diagram language by using the configuration software. Mimic configuration with Relay Mimic Editor 

The Relay Mimic Editor, which is included in the CAP 505 Relay Product Engineering Tools, is used for configuring the graphic dis play and the alarm channels of the transformer terminal. The mimic configuration may include circuit breakers, disconnectors, indicators, measurement data objects and user-defined texts and explanations. Any configuration can be saved for later use. 8

Self-supervision

The transformer terminal RET 54_ is provided with an extensive self-supervision system. The self-supervision system handles run-time fault situations and informs the user  of faults via the HMI and LON/SPA bus communication. When a fault has been detected, the green Ready indicator starts flashing, a fault indication text is displayed on the HMI and an event 0/E57 is generated. The fault indication text on the HMI consists of two rows: a general message ‘internal fault’, followed by the generated IRF code of the fault. The relay will try to recover from a fault either by restarting the module (I/O module or HMI) that reported the fault, or by restarting the whole relay. During restarting the IRF state will remain active until the internal selfsupervision program has determined that the relay is operating normally. If the fault is still  persistent after restarting three times, the relay will be in permanent IRF state.

All of the eight alarm function blocks can be configured in the same alarm view of the mimic editor. ON and OFF state texts (only one language version at a time can be sup ported for the alarm) and LED colours can be defined. Three different colours can be used to define the ON and OFF state. Three basic modes are available: • non-latched • latched-steady • latched flashing Interlocking LED texts can also be defined in the same alarm view but the colour of the interlocking LED cannot be changed. LON network configuration

The LON Network Tool is used for binding network variables between the transformer  terminal units. Typically, LON horizontal communication is used for transferring object status data (open, close, undefined) between units for interlocking purposes. Additionally, LON horizontal communication is used to transfer measured current amplitude and  phase angle information between terminals, when parallel control with MCC principle is to be applied. DNP 3.0 and Modbus configuration

The Protocol Mapping Tool is used for configuring the DNP 3.0 and Modbus interfaces of the transformer terminal.

Transformer Terminal

RET 541, RET 543, RET 545 1MRS755543

Transformer terminal parameterization

The parameters of the transformer terminal units can be set either locally over the HMI or  externally via the serial communication using the Relay Engineering Tools CAP 501/505. Local parameterization

When the parameters are set locally, the setting parameters can be chosen from the hierarchical menu structure. The desired language for parameter description can be selected.

Auxiliary voltage

For its operation, the RET 54_ t erminal, including the external display module, requires a secured auxiliary voltage supply. The terminal’s internal power supply module forms the voltages required by the terminal electronics. The power supply module is a galvanically isolated (fly-back type) dc/dc converter. A green protection LED indicator on the front  panel is lit when the power supply module is in operation.

Terminal connections

All external circuits are connected to the terminal blocks on the rear panel, see figures 2...4. The terminal block for the measuring transformers consists of fixed screw terminals. The serial interface RS-232 on the rear panel is used for connecting the transformer terminal to the SPA bus, the IEC_103, DNP 3.0 or  Modbus. The SPA/IEC_103 is connected via a connection module type RER 123 fitted to the 9-pin D-type subminiature connector and screwed to the rear panel. DNP 3.0/Modbus is connected via a connection module, type RER 133.

External parameterization

The Relay Setting Tool is used for parameterizing and setting the transformer terminals externally. The parameters can be set off-line on a PC and downloaded to the transformer  terminal over a communication port. The menu structure of the setting tool, including views for parameterization and settings, is the same as the menu structure of the transformer  terminal.

Power supply modules

There are two basic types of power supply modules available for the RET 54_: type PS1/_ and type PS2/_. The operating range of  digital inputs depends on the type of the  power supply module. See Technical data.

The serial interface RS-485 on the rear panel is used for connecting the transformer terminal to the SPA bus or the LON bus. The SPA/LON bus is connected via a connection module type RER 103 fitted to the 9-pin Dtype subminiature connector and screwed to the rear panel. The digital input and output contacts of the transformer terminal are connected to the multi-pole connectors. Protective earth is connected to the screw marked with the earth symbol.

9

Transformer Terminal

RET 541, RET 543, RET 545 1MRS755543

Terminal diagrams

+ PS1_4_ACFail

Mains -

PS1_4_TempAlarm

X4.1 1 2

X1.1 27

100V

Ch 10, VT2

SERIALBUS

25 24 22 21

1A 5A

Ch 9, CT7

SERIALBUS 1A 5A

Ch 8, CT6

16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

1A 5A

100V

1A 5A

1A 5A

1A 5A

1A 5A

IR F

Ch 7, CT5

X3.3

X4.1 3 4

19 18

X3.2

Ch 6, VT1

5 6

+

Ch 5, CT4

Ch 4, CT3

7 9 8

PS1_4_HSPO3

10

+

Ch 3, CT2

PS1_4_HSPO1 Ch 2, CT1

PS1_4_TCS1

TCS

11 13 12 15

PS1_4_HSPO2 PS1_4_TCS2

TCS

16 18 17

X4.2 8

PS1_4_HSPO4

9 11 10

PS1_4_BI1

12

PS1_4_HSPO5

13 15 14

-

X4.2 1 2

-

4 5

PS1_4_BI2

-

6 7

PS1_4_BI3

X5.1 1 2 3

BIO1_5_BI1

-

16 17

PS1_4_SO1

18

BIO1_5_BI2

-

4 5 6

-

7 8 9

BIO1_5_BI3 X5.2 3

BIO1_5_BI4 BIO1_5_BI5

BIO1_5_SO1

BIO1_5_BI6

-

10 11 12

BIO1_5_BI7

BIO1_5_SO2

13 14 15

-

16

-

17 18

BIO1_5_BI9

6 7 9

BIO1_5_BI8

-

4 5

BIO1_5_SO3

8 10 12

BIO1_5_BI10 BIO1_5_BI11

BIO1_5_SO4

11 13 15

X5.2 1 -

2

BIO1_5_BI12

BIO1_5_SO5

BIO1_5_SO6

14 16 18 17

RET 541

CD541

Fig. 2 10

Sample connection diagram of RET 541

Transformer Terminal

RET 541, RET 543, RET 545 1MRS755543

+ PS1_4_ACFail

Mains -

PS1_4_TempAlarm X1.1 27

100V

Ch 10, VT2

SERIALBUS

25 24 22 21 19 18 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

1A 5A

1A 5A

100V

1A 5A

1A 5A

1A 5A

1A 5A

1 2

X3.2

Ch 9, CT7

SERIALBUS 1A 5A

X4.1

Ch 8, CT6

X4.1 3 4

IR F

Ch 7, CT5

X3.3

Ch 6, VT1

5 6

+

Ch 5, CT4

Ch 4, CT3

PS1_4_HSPO3

7 9 8

PS1_4_HSPO1 PS1_4_TCS1

11 13 12

10

+

Ch 3, CT2

Ch 2, CT1

TCS

15

PS1_4_HSPO2 PS1_4_TCS2

TCS

16 18 17

X4.2 8

-

X4.2 1 2

PS1_4_HSPO4 PS1_4_BI1

-

4 5

PS1_4_BI2

-

6 7

PS1_4_BI3

X5.1 1 2 3

BIO1_5_BI1

-

9 11 10 12

PS1_4_HSPO5

13 15 14 16 17

PS1_4_SO1

18

BIO1_5_BI2

-

4 5 6

-

7 8 9

BIO1_5_BI3 X5.2 3

BIO1_5_BI4 BIO1_5_BI5

BIO1_5_SO1

BIO1_5_BI6

-

10 11 12 13

-

14

BIO1_5_BI7

BIO1_5_SO2

BIO1_5_SO3

16

BIO1_5_BI10

17

-

18

8 10 12

15

-

6 7 9

BIO1_5_BI8 BIO1_5_BI9

4 5

BIO1_5_BI11

BIO1_5_SO4

11 13 15

X5.2 1

-

2

BIO1_5_BI12

BIO1_5_SO5

BIO1_5_SO6

14 16 18 17

X7.1

BIO2_7_PO1

17 18 X7.2

X7.1

1 2 3 4 5 6 7 8 9 10 11 12

BIO2_7_PO2 BIO2_7_BI1

1 2 3

BIO2_7_BI2 BIO2_7_BI3

BIO2_7_PO3

BIO2_7_BI5

BIO2_7_PO4

BIO2_7_BI6

BIO2_7_PO5 BIO2_7_BI8 BIO2_7_BI9

15 16

BIO2_7_BI10

8 9 10 11

BIO2_7_BI7

13 14

4 5 6 7

BIO2_7_BI4

12 13 14 15

BIO2_7_PO6

16 17 18

RET 543

CD543

Fig. 3

Sample connection diagram of RET 543 11

Transformer Terminal

RET 541, RET 543, RET 545 1MRS755543

X4.1

+ PS2_4_ACFail

Mains

1

-

2

PS2_4_TempAlarm X1.1 27

100V

Ch 10, VT2

SERIALBUS

25 24 22 21 19 18 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

1A 5A

Ch 9, CT7

SERIALBUS 1A 5A

1A 5A

100V

1A 5A

1A 5A

1A 5A

1A 5A

Ch 8, CT6

X3.3

X4.1 3 4

IR F

Ch 7, CT5

X3.2

Ch 6, VT1

5 6

+

Ch 5, CT4

Ch 4, CT3

PS2_4_HSPO3

7 9 8

PS2_4_HSPO1 PS2_4_TCS1

11 13 12

10

+

Ch 3, CT2

Ch 2, CT1

TCS

15

PS2_4_HSPO2 PS2_4_TCS2

TCS

16 18 17

X4.2 1

PS2_4_HSPO4

PS2_4_HSPO5

-

X5.1 1 2 3

PS2_4_HSPO6 BIO1_5_BI1

2 4 3 5 6 8 7 9 10 12 11 13

BIO1_5_BI2

-

4 5 6

-

7 8 9

PS2_4_HSPO7

BIO1_5_BI3

14 16 15

BIO1_5_BI4 BIO1_5_BI5 PS2_4_HSPO8

17 18

BIO1_5_BI6

-

10 11 12

X5.2 3

BIO1_5_BI7 BIO1_5_SO1

BIO1_5_BI8 13 -

14

BIO1_5_SO2

15 -

16

4 5

BIO1_5_BI9

6 7 9

BIO1_5_BI10

17 -

18

BIO1_5_BI11 BIO1_5_SO3

1 -

2

8 10 12

X5.2 BIO1_5_BI12 BIO1_5_SO4

11 13 15

BIO1_5_SO5 X6.1

1 2 3 4 5 6 7 8 9

10 11 12 13 14 15 16 17 18

2

BIO1_5_SO6

BIO1_6_BI2 BIO1_6_BI3

3

BIO1_6_SO1

BIO1_6_BI5 BIO1_6_BI6

BIO1_6_SO2

7 8 9 10 11 12

4 5 6 7 9

BIO1_6_BI7 BIO1_6_BI8 BIO1_6_SO3

8 10 12

BIO1_6_BI9 BIO1_6_BI10 BIO1_6_SO4

11 13 15

BIO1_6_BI11

BIO1_6_SO5 BIO1_6_BI12 BIO1_6_SO6

4 5 6

17

X6.2

BIO1_6_BI4

X7.1

1 2 3

16 18

BIO1_6_BI1

X6.2

1

14

14 16 18 17 X7.1

BIO2_7_BI1 BIO2_7_PO1

BIO2_7_BI2

17 18 X7.2

BIO2_7_BI3 BIO2_7_PO2

BIO2_7_BI4

1 2 3

BIO2_7_BI5 BIO2_7_PO3

BIO2_7_BI6 BIO2_7_BI7 BIO2_7_BI8

13 14

BIO2_7_BI9

15 16

BIO2_7_BI10

BIO2_7_PO4

BIO2_7_PO5

4 5 6 7 8 9 10 11 12 13 14 15

BIO2_7_PO6

16 17 18

RET 545 CD545_b

Fig. 4 12

Sample connection diagram of RET 545

Transformer Terminal

RET 541, RET 543, RET 545 1MRS755543

Technical data Table 1: General functions available for the RET 54_  Function

Description

INDRESET

Resetting of operation indicators, latched output signals, registers and waveforms i.e. the disturbance recorder 

MMIWAKE

Activation of HMI backlight

SWGRP1

Switchgroup SWGRP1

SWGRP2

Switchgroup SWGRP2

SWGRP3

Switchgroup SWGRP3

...... SWGRP20

Switchgroup SWGRP20

Table 2: Standard functions available for the RET 54_  Function

Description

 ABS

Absolute value

 ACOS

Principal arc cosine

 ADD

Extensible adder 

 AND

Extensible AND connection

 ASIN

Principal arc sine

 ATAN

Principal arc tangent

BCD2INT

Type conversion from BCD coded input to SINT (Tap changer)

BITGET

Get one bit

BITSET

Set one bit

BOOL_TO_*

Type conversion from BOOL to WORD / USINT / UINT / UDINT / SINT / REAL / INT / DWORD / DINT / BYTE

BOOL2INT

Type conversion from BOOL inputs to INT output

BYTE_TO_*

Type conversion from BYTE to WORD / DWORD

COMH

Hysteresis comparator  

COS

Cosine in radians

CTD

Down-counter  

CTUD

Up-down counter  

CTU

Up-counter  

DATE_TO_UDINT

Type conversion from DATE to UDINT

DINT_TO_*

Type conversion from DINT to SINT / REAL / INT

DIV

Divider

DWORD_TO_*

Type conversion from DWORD to WORD / BYTE

EQ

Extensible comparison to equal

EXP

Natural exponential

 

EXPT

Exponentiation

F_TRIG

Falling edge detector  

GE

Extensible comparison to greater or equal

GRA Y2INT

Type conv er sion fr om GRAY coded i nput to S INT (Tap changer )

GT

Extensible comparison to greater  

INT_TO_*

Type conversion from INT to REAL / DINT

INT2BOOL

Type conversion from INT input to BOOL outputs

LE

Extensible comparison to less or equal

LIMIT

Limitation

LN

Natural logarithm

LOG

Logarithm base 10

LT

Extensible comparison to less

MAX

Extensible maximum

MIN

Extensible minimum

MOD

Modulo

MOVE

Move 13

Transformer Terminal

RET 541, RET 543, RET 545 1MRS755543

Table 2: Standard functions available for the RET 54_  Function

Description

MUL

Extensible multiplier  

MUX

Extensible multiplexer  

NAT2INT

Type conversi on from natur al bi nary coded input to S INT (Tap changer)

NE

Comparison to greater or less

NOT

Complement

OR

Extensible OR connection

R_TRIG

Rising edge detector  

REAL_TO_*

Type conversion from REAL to USINT / UINT / UDINT / SINT / INT / DINT

ROL

Rotate to left

ROR

Rotate to right

RS

Reset dominant bistable function block

RS_D

Reset dominant bistable function block with data input

SEL

Binary selection

SHL

Bit-shift to left

SHR

Bit-shift to right

SIN

Sine in radians

SINT_TO_*

Type conversion from SINT to REAL / INT / DINT

SUB

Subtractor  

SQRT

Square root

SR

Set dominant bistable function block

XOR

Extensible exclusive OR connection

TAN

Tangent in radians

TIME_TO_*

Type conversion from TIME to UDINT / TOD / REAL

TOD_TO_*

Type conversion from TOD to UDINT / TIME / REAL

TOF

Off-delay timer 

TON

On-delay timer 

TP

Pulse

TRUNC_REAL_TO*

Truncation toward zero from REAL to DINT / INT / SINT / UDINT / UINT / USINT

UDINT_TO_*

Type conversi on from UDINT to USINT / UINT / RE AL

UINT_TO_*

Type conversi on from UINT to USINT / UDINT / RE AL / B OOL

USINT_T O_*

Type conversi on from US INT to UINT / UDINT / RE AL

WORD_TO_*

Type conversion from WORD to DWORD / BYTE

Table 3: Conditioning monitoring functions available for the RET 54_ 

14

Function

Description

CMBWEAR1

Circuit-breaker electric wear 1

CMBWEAR2

Circuit-breaker electric wear 2

CMCU3

Supervision function of the energizing current input circuit

CMGAS1

Gas pressure monitoring

CMGAS3

Three-pole gas pressure monitoring

CMSCHED

Scheduled maintenance

CMSPRC1

Spring charging control 1

CMTCS1

Trip circuit supervision 1

CMTCS2

Trip circuit supervision 2

CMTIME1

Operate time counter 1 for the operate time used (e.g. motors)

CMTIME2

Operate time counter 2 for the operate time used (e.g. motors)

CMTRAV1

Breaker travel time 1

CMVO3

Supervision function of the energizing voltage input circuit

Transformer Terminal

RET 541, RET 543, RET 545 1MRS755543

Table 4: Control functions available for the RET 54_  Function

Description

CO3DC1

Three- state disc onnector 1 with indication

CO3DC2

Three- state disc onnector 2 with indication

COCB1

Circuit breaker 1 control with indication

COCB2

Circuit breaker 2 control with indication

COCBDIR

Direct open for CBs via HMI

CODC1

Disconnector 1 control with indication

CODC2

Disconnector 2 control with indication

CODC3

Disconnector 3 control with indication

CODC4

Disconnector 4 control with indication

CODC5

Disconnector 5 control with indication

COIND1

Switching device 1 indication

COIND2

Switching device 2 indication

COIND3

Switching device 3 indication

COIND4

Switching device 4 indication

COIND5

Switching device 5 indication

COIND6

Switching device 6 indication

COIND7

Switching device 7 indication

COIND8

Switching device 8 indication

COLOCAT

Logic-controlled control position selector 

COLTC

On-l oad tap changer control ler (vol tage r egulator)

COSW1

On/off switch 1

COSW2

On/off switch 2

COSW3

On/off switch 3

COSW4

On/off switch 4

MMIA LA R1

Al arm channel 1, LED indi cator  

MMIA LA R2

Al arm channel 2, LED indi cator  

MMIA LA R3

Al arm channel 3, LED indi cator  

MMIA LA R4

Al arm channel 4, LED indi cator  

MMIA LA R5

Al arm channel 5, LED indi cator  

MMIA LA R6

Al arm channel 6, LED indi cator  

MMIA LA R7

Al arm channel 7, LED indi cator  

MMIA LA R8

Al arm channel 8, LED indi cator  

MMIDATA 1

MIMIC data moni tori ng point 1

MMIDATA 2

MIMIC data moni tori ng point 2

MMIDATA 3

MIMIC data moni tori ng point 3

MMIDATA 4

MIMIC data moni tori ng point 4

MMIDATA 5

MIMIC data moni tori ng point 5

15

Transformer Terminal

RET 541, RET 543, RET 545 1MRS755543

Table 5: On-load tap changer controller function block On load tap changer control function (voltage regulator), COLTC Reference voltage

0.000 ... 2.000 xUn

Delay time for the 1st control pulse

1.0 ... 300.0 s

Delay time for the 2nd control pulse

1.0 ... 300.0 s

Resistive line-drop compens. factor (Ur)

0.0 ... 25.0 %Un

Reactive line-drop compens. factor (Ux)

0.0 ... 25.0 %Un

Load phase angle (in NRP mode)

-89 ... +89 deg

Stability factor in parallel operation

0.0 ... 70.0 %Un

Operation mode

Not in use Manual  Automatic single  Automatic master   Automatic follower  Negative Reactance Principle Minimizing Circulating Current Controlled via op.mode inputs

Delay mode

Definite time Inverse time

Raise and lower pulse duration

0.5 ... 10.0 s

Bandwith

0.60 ... 9.00 %Un

Overcurrent blocking limit

0.10 ... 5.00 xIn

Undervoltage blocking limit

0.10 ... 1.20 xUn

Overvoltage blocking limit

0.80 ... 1.60 xUn

High circ. current blocking limit

0.10 ... 5.00 xIn

Max limit for LDC term

0.00 ... 2.00 xUn

Reduce Set Voltage step

0.00 ... 9.00 %Un

Max volt tap

-36 ... 36

Min volt tap

-36 ... 36

Max parallel trafos in MCC mode

4

Operation accuracies - voltage measurement:

- lower and raise output pulse duration:

Depends on the frequency of the voltage measured: f/fn = 0.95 ... 1.05: +1.0% of the set value or  +0.01xUn +1% of the set value or +250 ms 250ms and an inaccuracy which occurs when voltage varies +0.5% +100 ms

Reset ratio (hysteresis)

20% of the set Bandwith

- operation time DT mode: - operation time IDMT mode:

Table 6: Measurement function blocks General measurement/ analog input on RTD/analog module, MEAI1...8 The general measurement function blocks can be used to measure general purpose dc or ac voltage signals with a sensor input. They also include a REAL type input which can be used to monitor any internal REAL type IEC 61131-3 based signal, e.g. input data from the RTD/analog module. GE1…3 (V dc/ac) General REAL type input

-10000.00000...10000.00000 -10000.00000...10000.00000

Analog output on RTD/analog module, MEAO1...4 The analog output function blocks handle the scaling of any internal REAL type IEC 61131-3 based signal to fit a selectable 0…20 mA or 4…20 mA range for use with the outputs on the RTD/analog module. General REAL type input

-10000.00000...10000.00000

Neutral current measurement, MECU1A and MECU1B Io (A) Io (%)

16

0.0…20000.0 A 0.0…80.0% In

Transformer Terminal

RET 541, RET 543, RET 545 1MRS755543

Three-phase current measurement, MECU3A and MECU3B IL1 IL2 IL3 IL1 IL2 IL3 IL1 demand IL2 demand IL3 demand IL1 demand IL2 demand IL3 demand

0.0…20000.0 A 0.0…20000.0 A 0.0…20000.0 A 0.0…1000.0% In 0.0…1000.0% In 0.0…1000.0% In 0.0…20000.0 A 0.0…20000.0 A 0.0…20000.0 A 0.0…1000.0% In 0.0…1000.0% In 0.0…1000.0% In

Transient disturbance recorder for 16 analog channels, MEDREC16 The transient disturbance recorder MEDREC16 is used for recording the current and voltage waveforms, as well as the status data of internal IEC 61131-3 based logic signals and digital inputs connected to the transformer terminals. Maximum 16 analog inputs and 16 logic signal inputs are available. One fundamental cycle contains 40 samples. Operation mode

Pre-trg time Over limit ILx Over limit Io Over limit Iob Over limit Uo Over limit Ux Over limit Uxy Over limit U12b Over limit ILxb Under limit Ux Under limit Uxy  AI filter time

Saturation Overwrite Extension 0…100% 0.00…40.00 x In 0.00…40.00 x In 0.00…40.00 x In 0.00…2.00 x Un 0.00…2.00 x Un 0.00…2.00 x Un 0.00…2.00 x Un 0.00…40.00 x In 0.00…2.00 x Un 0.00…2.00 x Un 0.000…60.000 s

The recording can be triggered by any (or several) of the alternatives listed below: • triggering on the rising or falling edge of any (or several) of the digital inputs • triggering on overcurrent, overvoltage or undervoltage • manual triggering via the menu or with the push-button F on the front panel (if configured) • triggering via serial communication • periodic triggering The recording length depends on the number of recordings and inputs used. For example, the following combination of recording length, number of recordings and number of inputs is available at 50 Hz (60 Hz):  recordings \  inputs

1

3

10

1

1163 cyc. 23.3 s (19.4 s)

412 cyc. 8.2 s (6.9 s)

126 cyc. 2.5 s (2.1 s)

5

232 cyc. 4.6 s (3.9 s)

82 cyc. 1.6 s (1.4 s)

25 cyc. 0.5 s (0.4 s)

10

115 cyc. 2.3 s (1.9 s)

41 cyc. 0.8 s (0.7 s)

12 cyc. 0.24 s (0.2 s)

System frequency measurement, MEFR1 Frequency  Average Freq. Voltage U

10.00…75.00 Hz 10.00…75.00 Hz 0.0…2.0 x Un

17

Transformer Terminal

RET 541, RET 543, RET 545 1MRS755543

Three-phase power and energy measurement, MEPE7 P3 (kW) Q3 (kvar) Power factor DPF Power factor PF P3 demand (kW) Q3 demand (kvar) Energy kWh Reverse kWh Energy kvarh Reverse kvarh

-999999…999999 kW -999999…999999 kvar  -1.00…1.00 -1.00…1.00 -999999…999999 kW -999999…999999 kvar  0…999999999 kWh 0…999999999 kWh 0…999999999 kvarh 0…999999999 kvarh

Residual voltage measurement, MEVO1A and MEVO1B Uo Uo

0…150000 V 0.0…120.0% Un

Three-phase voltage measurement, MEVO3A and MEVO3B UL1_U12 UL2_U23 UL3_U31 UL1_U12 UL2_U23 UL3_U31 UL1_U12 average UL2_U23 average UL3_U31 average UL1_U12 average UL2_U23 average UL3_U31 average

18

0.00…999.99 kV 0.00…999.99 kV 0.00…999.99 kV 0.00…2.00 x Un 0.00…2.00 x Un 0.00…2.00 x Un 0.00…999.99 kV 0.00…999.99 kV 0.00…999.99 kV 0.00…2.00 x Un 0.00…2.00 x Un 0.00…2.00 x Un

Transformer Terminal

RET 541, RET 543, RET 545 1MRS755543

Table 7: Protection function blocks Three-phase non-directional overcurrent protection, low-set stages, NOC3Low, 3I>, NOC3LowB,3I> Start current Operate time at DT mode Time multiplier at IDMT mode Operation mode

Measuring mode Drop-off time of the operate time counter  Operation accuracy Start time: - Injected currents - internal time - total time Reset time Reset ratio, typically Retardation time Operate time accuracy at DT mode  Accuracy class index E at IDMT mode

0.10…5.00 x In 0.05…300.00 s 0.05…1.00 Not in use Definite time Extremely inverse Very inverse Normal inverse Long time inverse RI-type inverse RD-type inverse IEEE curves Peak-to-peak Fundamental frequency 0...1000 ms Note! The values below apply when f/fn = 0.95...1.05 ±2.5% of set value or ±0.01 x In >2.0 x start current: , and instantaneous stage, NOC3Inst, 3I>>> Start current Operate time Operation mode

0.10…40.00 x In 0.05…300.00 s Not in use Definite time Instantaneous

Measuring mode

Peak-to-peak Fundamental frequency 0...1000 ms

Drop-off time of the operate time counter  Operation accuracy Start time: - injected currents - internal time - total time Reset time Reset ratio, typically Retardation time Operate time accuracy at DT mode

Note! The values below apply when f/fn = 0.95...1.05 0.1...10 x In: ±2.5% of set value or ±0.01 x In 10...40 x In: ±5.0% of set value >2.0 x start current: 2.0 x start current: and instantaneous stageDOC6Inst, I>>> Operation mode

Start current Operate time Basic angle b Operation direction Earth-fault protection Non-directional operation (when the direction cannot be determined) Measuring mode

Drop-off time of the operate time counter 

20

Not in use Definite time Instantaneous 0.05…40.00 x In 0.05…300.00 s 0…90 Forward Reverse Disabled Enabled Disabled Enabled Phase-to-phase voltages, peak-to-peak measurement Phase-to-phase voltages, fundamental freq. measurement Phase-to-earth voltages, peak-to-peak measurement Phase-to-earth voltages, fundamental freq. measurement 0...1000 ms

Transformer Terminal

RET 541, RET 543, RET 545 1MRS755543

Operation accuracy

Start time: - injected currents - internal time - total time Reset time Reset ratio, typically Retardation time Operate time accuracy at DT mode

Note! The values below apply when f/fn = 0.95...1.05 0.1...10 x In: ±2.5% of set value or ±0.01 x In 10...40 x In: ±5.0% of set value ±2.5% of measured voltage or ±0.01 x Un ±2 >2.0 x start current:  and instantaneous stage, DEF2Inst, I 0>>> Start current Start voltage Operate time Operation mode

Operation criteria

Operation direction Basic angle b

Operation characteristic Intermittent E/F Measuring mode Drop-off time of the operate time counter  Operation accuracy

Start time, injected neutral current and residual voltage - internal time - total time Reset time Reset ratio, typically Retardation time Operate time accuracy at DT mode

1.0…200.0% of In 2.0…100.0% of Un 0.1…300.0 s Not in use Definite time Instantaneous Basic angle & Uo Basic angle IoSin/Cos & Uo IoSin/Cos Non-directional Io Non-directional Uo Forward Reverse -90 -60 -30 0 IoSin() IoCos() Not active  Active Peak-to-peak Fundamental frequency 0...1000 ms Note! The values below apply when f/fn = 0.95...1.05 ±2.5% of set value + 0.0005 x In ±2.5% of set value or + 0.01 x Un Phase angle ±2  Injected neutral current >2.0 x start current and residual voltage >2.0 x start voltage 2nd harmonic blocking Operation accuracy of differential current measurement Operation accuracy of phase angle measurement Start time: -injected currents - internal time - total time Reset time Reset ratio, typically Retardation time (Total retardation time when the current drops below the start value) Operation time accuracy at definite time mode

0.5...50% 0.04...300.00 s 10...50 % Not in use / In use Note! The values below apply when f/fn = 0.95...1.05 ±4% of set value or ±0.02 x In ±2%

>2.0 x operating current: >> Start voltage Operate time Operation mode Measuring mode

Operation accuracy Start time - injected voltages - internal time - total time Reset time Reset ratio, typically Retardation time Operate time accuracy at DT mode

26

2.0…80.0% of Un 0.05…300.00 s Not in use Definite time Peak-to-peak Fundamental frequency Note! The values below apply when f/fn = 0.95...1.05 ±2.5% of set value or ±0.01 x Un >2 x start voltage 500 kW Generator; hydro or small air-cooled turbine generators Generator; large turbine generators Transformer  80.0…120.0% 40.0…100.0% 40.0…100.0% -50.0…100.0C 1.0...10.0 x time constant 1...999 min 0.0...999.0 min 0.0...999.0 min 0.00...1.00 0.0...350.0 C 0.0...350.0 C 0.0...999.0 min 0.0...999.0 min 0.00...1.00 0.0...350.0 C 0.0...350.0 C Not in use No sensors; the set ambient temperature 1 sensor used 2 sensors used 0...86400 s 0...86400 s Note! The values below apply when f/fn = 0.95...1.05 ±1.0%, I = 0.1...10.0 x In (Calculated temp. rise - 0.1) / Trip temperature (Calculated temp. rise - 0.1) / Prior alarm temperature (Calculated temp. rise - 0.1) / Restart inhibit temperature limit

27

Transformer Terminal

RET 541, RET 543, RET 545 1MRS755543

Negative phase-sequence protection, low-set stage, NPS3Low, I 2>, and high-set stage, NPS3High, I 2>> Operation mode

Start value of negative-sequence current I2 Operate time Operating characteristic constant K (corresponds to the machine constant, equal to the I 22t constant of the machine as stated by machine manufacturer) Definite start time at inverse-time mode Definite minimum operate time Maximum operate time Cooling time of the machine Number of phases to be measured Rotation direction Drop-off time of the operate time counter  Operation accuracy Start time: - injected negative-seq. current - internal time - total time Reset time Reset ratio, typically Retardation time Operate time accuracy at DT mode  Accuracy class index E at IDMT mode, typically

Not in use Definite time Inverse time 0.01...0.50 x In 0.1....120.0 s 5.0...100.0

0.1...60.0 s 0.1...120.0 s 500...10000 s 5...10000 s 2 or 3 Forward Reverse 0...1000 ms Note! The values below apply when f/fn = 0.95...1.05 ±2.5% of set value or ±0.01 x In = 2.00 x start value ; U1< & U1>; U2>; U1 Forward; Reverse; Input ROT_DIR Note! The values below apply when f/fn = 0.95...1.05 ± 2.5% of set value or ± 0.01 x Un = 1.1 x start value

RET/3I

87T

REF/4I DI0>

87TN

LV 3 I2> p>    I    1    /    T    E    R

Q

HV

Q

3I2f > HV

   I    1    /    F    E    R

49T 46 68

3I>

51

HV

50

3I>

51

LV

50

I 0>

51N

HV

50N

I0>

51N

LV

50N

000

000

51

3I

I0

000

50 3I

I0>

I0

51N 50N

3I

LO

U

o

86

R TCS

R

I0 o

TO

Tw

CBFP 62BF

TCS U

U

CBFP 62BF

CBFP 62BF

REF 610

HV

RET/RTD

3I>

90

LV

RET 54_ 

RET/1U REF/3U

3I>

51

3U>

59

3U<

27

000

50 REF/3I

I0>

51N 50N

RET/3I

CBFP 62BF

3I

I0 R

3U P

Q

TCS

REF 54_  MF

Dyn-trafo_impEarthedLVn

Fig. 7

52

Protection, control, measurement and supervision functions of an Dyn-connected power transformer, implemented with RET 543 transformer terminal and an REF 543 feeder terminal. The neutral point of the low-voltage network is earthed via a high impedance. REF 610 is used as a backup relay on the high-voltage side. This sceme can be applied also for parallel connected transformers.

Transformer Terminal

RET 541, RET 543, RET 545 1MRS755543

M       U       3       /       F       E       R

M

      U       3       /       F       E       R

MF

3I>

51 50

3U>

59

3I 2f >

68

3U<

27

I0>

51N

000

3I

I0 R

3U

TCS

50N

RET/3I

CBFP 62BF

REF/3I REF 54_  87T

M

ΔI0 >

ΔI0 >

REF/1I

HV

50

87TN

3I> LV

51 50

3I

I0

87TN

I0>

51N 50N

3I

U

LV

M

3

M

HV 49T

M

M

Θ

I0> LV

Θ

P>

3I 2f > HV

68

51N 50N

R

I0 TO

Tw

CBFP 62BF

RET/1U

REF/1I

3I>

67

3U>

59

I0>

51N 50N

3U<

27

CBFP 62BF

f> df/dt

81O 81O-R

REF,REA/3I

RET/1I

RET/3I

U

HV

RET 54_ 

TCS U

LV CBFP 62BF

M

000

51

HV

RET/1I

000

3I>

3ΔI>

90

000

3I> &

3I

I0

3U

pf 

P

Q

3I-harm

R TCS

REA 101

f 

3U-harm       U       3       /       F       E       R

      U       3       /       F       E       R

REF 54_ 

MF

M

E

M

YNd transformer with earthing transformer on LV side

Fig. 8

Protection, control, measurement and supervision functions of a YNd-connected power transformer, implemented with an RET 543 transformer terminal, REF 543 feeder terminals and REA 101 arc protection. The low-voltage network is earthed via a zig-zag earthing transformer.

53

Transformer Terminal

RET 541, RET 543, RET 545 1MRS755543

M

R E  F   /      3    U

M

MF

R E  F   /      3    U

3I>

51

3U>

59

3U<

27

000

50 3I 2f >

68

I0>

51N 50N

3I

I0

RET/3I REF/3I

R

3U

TCS

CBFP 62BF REF 54_ 

M

3ΔI > 87T

3I>

51

HV

50

87TN

3I> LV

51 50

87TN

I0>

51N

HV

50N

I0>

51N 50N

RET/1I Θ

REF/1I

P>

M

Θ

ΔI0 >

HV RET/RTD

ΔI0>

LV 3

R E  T   /     1   I    

49T

LV

R E  F   /     1   I    

3I 2f >

68

HV

3I

I0

3I

U R

I0 TO

Tw

LV

REF, REA/3I

U

HV

RET 54_  R E  F   /      3    U

TCS U

CBFP 62BF CBFP 62BF

R E  T   /     1    U

000

000

3I>

67

3U>

59

I0>

51N

3U<

27

90

000

3I> &

RET/3I

3I

I0

3U

pf 

50N MF

CBFP 6 2B 2BF

REF 54_ 

f> 81 O df/dt 81O-R

R TCS

f 

REA 101

CBCM

E

MCS

YNyn transformers impedance earthed LV neutral

Fig. 9

54

Protection, Protection, control, control, measurem measurement ent and and supervisio supervision n functions functions of YNyn-conn YNyn-connected ected power transformtransformers, implemented with RET 543 transformer terminals, REF 543 feeder terminals and REA 101 arc protection. The neutral point of the low-voltage network is earthed via a low resistance. The scheme is also applicable to other types of low-impedance earthed networks, where the neutral point is earthed effectively or via a low reactance. This sceme can be applied also for parallel connected transformers.

Transformer Terminal

RET 541, RET 543, RET 545 1MRS755543

3U<

27

3U>

59

U0>

59N

3U

U0

000

M    )    i    U   U    t    l    3    1    /    u    /    X   X    M    (    E   E    U   R   R    2    /    T    E    R

MF

CBCM R TCS

RET/4I (Basic)

MCS RET/3I (Multi)

REX 521 H06 3DI > 87TG M

M

DI0 >

87TN

LV Q

p>

M

Q

3I>

51

HV

50

3I>

51

LV

50

3I2f > HV

68

I0>

51N

HV

50N

I0>

51N

LV

50N

3

49T

3I

I0 I0

3I

000

R

f>

81O

df/dt

81O-R

f< df/dt

81U 81U-R

U/f>

24

TCS

000

000

R U

CBFP 62BF

Z<

21

U<

27

HV CBFP 62BF

f  TO

TTC

U U

LV T

RET/1I (Basic) REF/1I

RET 54_ (Basic)

RET/1U (Multi)

3I>

51

RET 54_ (Multi)

3U>

59

3U<

27

U0 >

59N

000

3I> &

50 I0> REF/3I, REA 101/3I

51N 50N

CBFP 62BF RET/3I (Basic)

MF

3I 3U

I0 R TCS

REA 101

   U    3    /    F    E    R

REF 54_ 

Yyn-trafo_highresEarthedLV

Fig. 10

Protection, Protection, control, control, measurem measurement ent and supervisio supervision n functions functions of an Yyn-connecte Yyn-connected d industrial industrial power  transformer, implemented with RET 543 transformer terminals, an REF 543 feeder terminal, an REX 521 protection relay and REA 101 arc protection. The neutral point of the low-voltage network is earthed via a high resistance.

55

Transformer Terminal

RET 541, RET 543, RET 545 1MRS755543

      U       3       /       1       2       5       X       E       R

MF

      U       1       /       1       2       5       X       E       R

RET_/3I

3DI>

DI0>

87TG 87TN

LV 3

49T

I2>

46

HV

3I>

51

HV

50

3I>

51

LV

50

I0>

51N

HV

50N

I0>

51N

LV

50N

000

3I

I0

3U<

27

3U>

59

U0>

59N

f>

81U

R 3I

U

TCS

I0 o

o

TO

Tw

3U

U0

000

f  CBCM R TCS MCS

CBFP 62BF HV

RET_/1I

REX 521 H06

RET 54_ 

Q Q

P>

3DI>

87G

X<

40

51

P>

32

000

REM_/3I REM_/3U REM_/1U

G 3~

REM/RTD REM_/3I

3I>

3I

P

Q

U

R

U0

pf 

TCS

50 I(U)>

51V

I2>

46

I0>

50N 51N

3

49G

3U>

59

3U<

27

RET_/3I

U0>

59N

o

T

f  F

Q>

MCS

60 49

E

38

CBFP 62BF

REM 54_  gener_blockconn-trafo1

Fig. 11

56

Transforme Transformerr in block connection connection with with a generator. generator. The The transformer transformer terminal terminal RET RET 543 is used for  for  overall differential protection. An earthing resistor is recommended for the generator. The REX 521 protection relay is used for abnormal voltage and frequency supervision and protection of the network and the machine.

Transformer Terminal

RET 541, RET 543, RET 545 1MRS755543

3DI> 87TG MF DI0 >

87TN

LV RET_/3I

3 I2>

49T 46

HV RET_/1U RET_/1U RET_/1I

3I>

51

HV

50

3I>

51

LV

50

I0>

51N

HV

50N

I0>

51N

LV

50N

U>

59N

000

3I

I0 R

3I

U

TCS

I0 o

o

TO

Tw

CBFP 62BF RET 54_ 

Q Q

3DI>

87G

f>/f<

81O 81U

Ios>

64S

X<

40

P>

32

P> REM_/3I (A) REM_/3I (B) REM_/2U(A)/3U(B) REM_/1U (A)

I> 2

000

46

CBFP 62BF

3I

P

Q

U

f 

pf 

R TCS MCS

E

G 3~ REM_/3I (A) RET_/3I REK 510

REM_/1I (A) REM/I0R (B)

REM 54_ (A) 3I>

51

000

P>

32

3

49G

3I

P

Q

3U

R

U0

pf 

TCS

50 Z<

21G

U/f>

24

F

60

IOR >

64R

3U>

59

MCS f 

3U<

27

CBFP 62BF E

U0 >

59N

REM 54_ (B) gen_blockconn-trafo2

Fig. 12

Transformer in block connection with a generator. The transformer terminal RET 543 is used for  overall differential protection. An earthing resistor is recommended for the generator. Generator  protection functions are divided for two REM 543 machine terminals (A and B). The current injection device REK 510 is used in the rotor earth-fault protection scheme.

57

Transformer Terminal

RET 541, RET 543, RET 545 1MRS755543

3I > 3I> I0>

50/51 67

= multiple-stage three-phase overcurrent protection, double low-set, high-set and instantaneous stages available (NOC3_) = multiple-stage three-phase directional overcurrent protection, low-set, high-set and instantaneous stage available (DOC6_)

50N/51N = multiple-stage earth-fault protection, low-set, high-set and instantaneous stage available (NEF1_)

I2>

46

= negative phase sequence (NPS) protection, low-set and high-set stages available (NPS3_)

3I2f >

68

= inrush detection based on the 2nd harmonic content of phase currents, applied for  preventing possible unnecessary operation of overcurrent or earth-fault protection during transformer switching-in or to start cold load pick-up logic (Inrush3_)

3D I >

87T

3D I >

87TG

= overall differential protection for generator and transformer blocks, stabilized and instantaneous stages (Diff6T)

DI0>

87TN

= restricted earth-fault (REF) protection, low- or high-impedance type (Diff3)

I(U)>

51V

= voltage-dependent overcurrent protection, low-set and high-set stages available (VOC6_)

I 0S>

64S

= stator earth-fault protection (NEF1_)

I 0R>

64R

= rotor earth-fault protection (NEF1_)

U/f

24

= overexcitation protection, low-set and high-set stages available (OE1_)

U<

27

= undervoltage protection, low-set and high-set stage available (UV3_)

3U <

27

= three-phase undervoltage protection, low-set and high-set stage available (UV3_)

3U >

59

= three-phase overvoltage protection, low-set and high-set stage available (OV3_)

U 0>

59N

= multiple-stage residual overvoltage protection, low-set, high-set and instantaneous stage available (ROV1_)

f>

81U

= overfrequency protection (incl. in Freq1St_)

f> df/dt

81U = overfrequency protection and frequency rate of change function (incl. in Freq1St_) 81U-R

f< df/dt

81O = underfrequency protection and frequency rate of change function (incl. in Freq1St_) 81O-R

f>/f<

81O 81U

= over/underfrequency protection (incl. in Freq1St_)

3

49G

= three-phase thermal overload protection for generator (TOL3Dev)

3

49T

= three-phase thermal overload protection for transformers (TOL3Dev)

Q>

49 38

= thermal supervision for generator windings and bearings with RTDs (MEAI_)

62BF

= circuit-breaker failure protection (included in all current-based short circuit and earth-fault protection function blocks)

CBFP

= three phase differential protection for transformers, stabilized and instantaneous stages (Diff3)

SYMNOT1_RET

Fig. 13

58

Symbol notations, part I

Transformer Terminal

RET 541, RET 543, RET 545 1MRS755543

Z<

21G

= underimpedance protection for generator, low-set and high-set stages (UI6_)

3Z<

21

= three-phase underimpedance protection, low-set and high-set stages (UI6_)

X<

40

= underexcitation protection, low-set and high-set stages (UE6_)

P>

32

= underpower, low-forward power or reverse power protection, stages 1, 2 and 3 available (UPOW6St_)

F

60

= fuse failure supervision (FuseFail)

3I > &

= arc protection with REA 101

MCS

= measuring circuit supervision

TCS

= trip circuit supervision

CBCM

U

U

= circuit-breaker condition monitoring

90V

= automatic voltage regulation (COLTC)

= manual voltage regulation (COLTC)

P

= active power measurement, indication and supervision

Q

= reactive power measurement, indication and supervision

3I

= 3-phase current measurement, indication and supervision

3U

= 3-phase voltage or phase-to-phase voltage measurement, indication and supervision

f 

= frequency measurement, indication and supervision

pf 

= power factor measurement, indication and supervision

I0

= residual current measurement, indication and supervision

U0

= residual voltage measurement, indication and supervision SYMNOT2_RET

Fig. 14

Symbol notations, part II

59

Transformer Terminal

RET 541, RET 543, RET 545 1MRS755543

U

= phase voltage or phase-to-phase voltage measurement, indication and supervision

oT

= oil temperature measurement, indication and supervision

o

oT

W

= transformer winding temperature measurement, indication and supervision

oT

TC

= tap changer temperature measurement, indication and supervision

oT

= ambient temperature measurement, indication and supervision

= energy counter, forward or reverse active / reactive energy (MEPE7)

E 3I-harm

= current waveform distortion measurement (PQCU3H)

3U-harm

= voltage waveform distortion measurement (PQVU3H) = annunciating, event generating and value recording functions

R

= disturbance recorder (MEDREC16) 000

= digital value indication

000

= HMI/MIMIC display

000

= tap changer position display

0

I

= local and remote control interface = bay-oriented interlocking logic SYMNOT3_RET

Fig. 15

60

Symbol notations, part III

Transformer Terminal

RET 541, RET 543, RET 545 1MRS755543

Application selection tables for RET 541, RET 543 and RET 545 functions Table 30: Protection functions Types of fault

IEEE Device No.

IEC Symbol

Protection function

Function block code

Differential protection

87T

3I>, 3I> >

Stabil ized and instantaneous differential protection for  transformers

Diff6T

Short circuit and overcurrent

51

3I>

Three-phase nondirectional overcurrent, low-set stage

NOC3Low

51

3I>

Three-phase nondirectional overcurrent, low-set stage

NOC3LowB

50/51/51B

3I>>

Three-phase nondirectional overcurrent, high-set stage

NOC3High

50/51B

3I>>>

Three-phase nondirectional overcurrent, instantaneous stage

NOC3Inst

67

3I>

Three-phase directional o/c, low-set stage

DOC6Low

67

3I>>

Three-phase directional o/c, high-set stage

DOC6High

67

3I>>>

Three-phase directional o/c, instantaneous stage

DOC6Inst

21

Z<

Three-phase underimpedance,low-set stage

UI6Low

21

Z/SEF

Non-directional earthfault, low-set stage (or  SEF = sensitive earthfault protection)

NEF1Low

50N/51N

Io>>

Non-directional earthfault, high-set stage

NEF1High

50N

Io>>>

Non-directional earthNEF1Inst fault, instantaneous stage

67N/51N

Io> /SEF

Directional earth-fault, low-set stage (or SEF = sensitive earth-fault protection)

DEF2Low

67N

Io>>

Directional earth-fault, high-set stage

DEF2High

67N

Io>>>

Directional earth-fault, instantaneous stage

DEF2Inst

59N

Uo>

Residual overvoltage, low-set stage

ROV1Low

59N

Uo>>

Residual overvoltage, high-set stage

ROV1High

59N

Uo>>>

Residual overvoltage, instantaneous stage

ROV1Inst

87N

Io>

High-impedance based restricted earth-fault protection

REF1A

Underimpedance

Earth fault

61

Transformer Terminal

RET 541, RET 543, RET 545 1MRS755543

Table 30: Protection functions Types of fault

IEEE Device No.

IEC Symbol

Protection function

Function block code

Earth-fault

87TN

Io>

Stabilized restricted earth-fault protection

REF4A

87TN

Io>

Stabilized restricted earth-fault protection

REF4B

Overload

49M/49G/49T

3

Three-phase thermal protection for devices (motors, generators and transformers)

TOL3Dev

Negative phaseseguence

46

I2>

Negative phaseseguence protection, low-set stage

NPS3Low

46

I2>>

Negative phaseseguence protection, high-set stage

NPS3High

59

3U>

Three-phase overvoltage, low-set stage

OV3Low

59

3U>>

Three-phase overvoltage, high-set stage

OV3High

27

3U<

Three-phase undervoltage, low-set stage

UV3Low

27

3U U1>

Phase-sequence voltage protection, stage 1

PSV3St1

27, 47, 59

U 1< U2> U1>

Phase-sequence voltage protection, stage 2

PSV3St2

81U/81O

f, df/dt

Underfrequency or   overfrequency, stage 1 (incl. rate of change)

Freq1St1

81U/81O

f, df/dt

Underfrequency or   overfrequency, stage 2 (incl. rate of change)

Freq1St2

81U/81O

f, df/dt

Underfrequency or   overfrequency, stage 3 (incl. rate of change)

Freq1St3

81U/81O

f, df/dt

Underfrequency or   overfrequency, stage 4 (incl. rate of change)

Freq1St4

81U/81O

f, df/dt

Underfrequency or   overfrequency, stage 5 (incl. rate of change)

Freq1St5

24

U/f>

Overexcitation protection, OE1Low low-set stage

24

U/f>>

Overexcitation protection, OE1High high-set stage

68

3I2f >

Three-phase transformer   Inrush3 inrush and motor start-up current detector 

60

FUSEF

Fuse failure supervision

Overvoltage/ undervoltage

Overfrequency/ underfrequency

Overexcitation

 Additional functions

62

FuseFail

Transformer Terminal

RET 541, RET 543, RET 545 1MRS755543

Table 31: Measurement functions Types of measurement

IEC Symbol

Measurement function

Function block code

General measurement/ analog input or analog output

mA/V/C/

General measurement/ analog input on RTD/analog module

MEAI1...8

mA

Analog output on RTD/analog module

MEAO1...4

3I

Three-phase current measurement, stage A

MECU3A

3I

Three-phase current measurement, stage B

MECU3B

Io

Neutral current measurement, stage A

MECU1A

Io

Neutral current measurement, stage B

MECU1B

3U

Three-phase voltage measurement, stage A

MEVO3A

3U

Three-phase voltage measurement, stage B

MEVO3B

Uo

Residual voltage measurement, stage A

MEVO1A

Uo

Residual voltage measurement, stage B

MEVO1B

Energy / Power

E, P, Q, pf

Three-phase power and energy measurement

MEPE7

Frequency

f

System frequency measurement

MEFR1

Transient disturbance recorder 

MEDREC16

Function block code

Current

Voltage

Recording

Table 32: Control functions Types of control

Symbol

Control function

Circuit breaker

0 1

Circuit breaker 1 (2 state COCB1 inputs / 2 control outputs)

0

1

Circuit breaker 2 (2 state COCB2 inputs / 2 control outputs)

0

1

Direct open for CBs via HMI

COCBDIR

0

1

Disconnector 1...5 (2 state inputs / 2 control outputs)

CODC1...CODC5

0

1

Three state disconnector   CO3DC1 1 (3 state inputs/ 4 control outputs)

0

1

Three-state disconnector   CO3DC2 2 (3 state inputs/ 4 control outputs)

Disconnector

63

Transformer Terminal

RET 541, RET 543, RET 545 1MRS755543

Table 32: Control functions Types of control

Symbol

Other control functions

Control function

Function block code

Object indication 1...8 (2 state inputs)

COIND1...COIND8

On/off switch 1...4 (1 output)

COSW1...COSW4

Logic control position selector 

COLOCAT

On-load tap changer  COLTC controller (voltage regul.) MIMIC dynamic data point 1...5

MMIDATA1...MMIDATA5

 Alarm 1...8 (HMI, remote)

MMIALAR1...MMIALAR8

Table 33: Condition monitoring functions Types of condition monitoring Circuit breaker

Trip circuit Measuring circuit

64

Symbol

Condition monitoring function

Function block code

CBCM

CB electric wear 1

CMBWEAR1

CBCM

CB electric wear 2

CMBWEAR2

CBCM

Operate time counter 1 for used operate time (motors)

CMTIME1

CBCM

Operate time counter 2 for used operate time (motors)

CMTIME2

CBCM

Gas pressure monitoring CMGAS1

CBCM

Three-pole gas pressure monitoring

CBCM

Spring charging control 1 CMSPRC1

CBCM

Breaker travel time 1

CMTRAV1

CBCM

Scheduled maintenance

CMSCHED

TCS

Trip Circuit Supervision 1 CMTCS1

TCS

Trip Circuit Supervision 2 CMTCS2

MCS

Supervision function of   the energizing current input circuit

CMCU3

MCS

Supervision function of   the energizing voltage input circuit

CMVO3

CMGAS3

References Additional information Transformer Terminal RET 54_ Technical Reference 1MRS755225 Manual, General Technical Descriptions of Functions

1MRS750889-MCD (CD-ROM only)

Installation Manual

1MR 750526-MUM

Operator’s Manual

1MR 750500-MUM

Technical Reference Manual RER 103

1MRS750532-MUM

Technical Reference Manual RER 123

1MRS751143-MUM

Protection & Control Terminals REF 54_, REM 54_, RET 54_ and REC 523 Configuration Guideline

1MRS750745-MUM

Bus Connection Module RER 133 Technical Description

1MRS755163

Echelon, LON and LonTalk are registered trademarks of Echelon Corporation. All other product names or brands are trademarks, registered trademarks, or service marks of their r espective owners.

Document changes Version Date

Changes

C

15.06.2005

Table 7: Reset ratio of OV3Low and OV3High changed from 0.96 to 1.04

D

28.05.2010

Document updated

E

26.10.2010

Document updated