Renault Scenic Trim and Upholstery
February 1, 2017 | Author: wofeba | Category: N/A
Short Description
Download Renault Scenic Trim and Upholstery...
Description
7
Trim and upholstery 71A
BODY INTERIOR TRIM
72A
SIDE OPENING ELEMENT LINING
73A
NON-SIDE OPENING ELEMENT LINING
75A
FRONT SEAT FRAMES AND RUNNERS
76A
REAR SEAT FRAMES AND RUNNERS
77A
FRONT SEAT TRIM
78A
REAR SEAT LINING
X84, and J84 77 11 322 182
FEBRUARY 2004
"The repair methods given by the manufacturer in this document are based on the technical specifications current when it was prepared. The methods may be modified as a result of changes introduced by the manufacturer in the production of the various component units and accessories from which his vehicles are constructed."
Edition Anglaise
All copyrights reserved by Renault. The reproduction or translation in part of whole of the present document, as well as the use of the spare parts reference numbering system, are prohibited without the prior written consent of Renault.
© Renault s.a.s. 2005
Scénic II - Section 7
Scénic II - Section 7 ContentsPage
Contents Page
71A
BODY INTERIOR TRIM
72A
SIDE OPENING ELEMENT LINING
Luggage compartment floor lining: Removal - Refitting
71A-1
Front side door trim: Removal - Refitting
72A-1
Centre floor front carpet: Removal - Refitting
71A-3
Front door flap: Removal Refitting
72A-4
Centre floor rear carpet: Removal - Refitting
71A-7
Rear side door trim: Removal - Refitting
72A-6
Rear door flap: Removal Refitting
72A-8
Luggage compartment carpet: Removal - Refitting
71A-12
Headlining: Removal Refitting
71A-13
Front door sill lining: Removal - Refitting
71A-19
B-pillar lower trim: Removal Refitting
73A
71A-20
Rear door sill lining: Removal - Refitting
71A-21
C-pillar lower trim: Removal Refitting
71A-23 75A
Rear wheel arch lining: Removal - Refitting
71A-24
A-pillar trim: Removal Refitting
71A-28
B-pillar upper trim: Removal Refitting
71A-29
Rear quarter panel trim: Removal - Refitting
71A-30
Rear end panel lining: Removal - Refitting
71A-33
76A
NON-SIDE OPENING ELEMENT LINING Tailgate lining: Removal Refitting
73A-1
Bonnet soundproofing: Removal - Refitting
73A-3
FRONT SEAT FRAMES AND RUNNERS Fixed front seat frame: Removal - Refitting
75A-1
Complete front seat: Removal - Refitting
75A-6
Front seat runner: Removal Refitting
75A-8
REAR SEAT FRAMES AND RUNNERS Complete rear seat: Removal - Refitting
76A-1
Second row complete rear seat: Removal - Refitting
76A-7
Contents
76A
77A
78A
REAR SEAT FRAMES AND RUNNERS Second row rear seat frame: Removal - Refitting
76A-11
Rear side seat mechanism: Removal - Refitting
76A-12
Rear central seat runners: Removal - Refitting
76A-14
Rear seat runner: Removal Refitting
76A-16
FRONT SEAT TRIM Front seatback trim: Removal - Refitting
77A-1
Front seat base trim: Removal - Refitting
77A-9
REAR SEAT LINING Rear seatback trim: Removal - Refitting
78A-1
Second row rear seat trim: Removal - Refitting
78A-4
Rear side seat trim: Removal - Refitting
78A-9
Rear centre seat trim: Removal - Refitting
78A-17
Rear seat base trim: Removal - Refitting
78A-20
BODY INTERIOR TRIM
71A
Luggage compartment floor lining: Removal - Refitting LONG CHASSIS
Tightening torquesm mounting bolts
2.1 daNm
REMOVAL Remove the boot carpet.
5 2 1
107115
Remove the cover (5) . 107117
Turn: - the catches (1) a quarter turn anticlockwise, - the catch (2) a quarter turn clockwise. Remove the flap.
3
4
22274
Remove the parking brake release handle.
107118
Unclip the centre stalk cover (3) . Turn the catch (4) a quarter turn anticlockwise. Remove the flap.
71A-1
BODY INTERIOR TRIM Luggage compartment floor lining: Removal - Refitting LONG CHASSIS
6
107116
Remove: - the bolts (6) , - the side trim panels.
8
7
107115
Remove the bolts (7) and (8) . Remove the centre trim.
REFITTING Proceed in the reverse order to removal. Torque tighten the mounting bolts ( 2.1 daNm ) .
71A-2
71A
BODY INTERIOR TRIM Centre floor front carpet: Removal - Refitting
71A
Tightening torquesm seat height adjuster mounting bolts
2.1 daNm
3 4
REMOVAL Remove: - the front seats (see 75A, Front seat frames and runners, Complete front seat: Removal - Refitting, page 75A-6) (observing the safety instructions), - the centre console( (see Centre console: Removal - Refitting) , - the floor storage compartments and flaps( (see Floor flap and storage: Removal - Refitting) ,( (see Underseat flap and storage: Removal - Refitting) .
5 104220
Unclip: - the floor sill lining (3) , - the door sill lining (4) and (5) .
1
104217
Remove the retaining clips using clip removal pliers. Remove the carpet.
2
104145
Unclip the trim (1) . Remove the trim (2) .
71A-3
BODY INTERIOR TRIM Centre floor front carpet: Removal - Refitting
71A
6
104219
104221
Unclip the side trim (6) . Note: Note:
Depending on the equipment level, the ventilation ducts may make it necessary to remove the seat height adjuster.
An aerial is clipped on the driver's side trim (depending on equipment level).
Unclip the seat connector from the clip. Remove the seat height adjuster mounting bolts.
104209
Unclip the front half-floor. 104200
Remove the duct.
71A-4
BODY INTERIOR TRIM Centre floor front carpet: Removal - Refitting
104202
Remove the intermediate duct.
71A
103598
Remove the gear lever knob.
104208
Remove the soundproofing padding.
103600
Unclip the gear lever gaiter.
Note: To remove the driver's side soundproofing padding, it must be cut away from the steering column.
71A-5
BODY INTERIOR TRIM Centre floor front carpet: Removal - Refitting
71A
103601
103604
Unclip the upper trim.
Disconnect the various connectors.
Disconnect the connector.
Unclip the trim. Remove the trim.
103603
Remove: - the three mounting bolts, - the side clips.
103586
Remove the centre soundproofing pad.
REFITTING Torque tighten the seat height adjuster mounting bolts ( 2.1 daNm ) . Proceed in the reverse order to removal.
71A-6
BODY INTERIOR TRIM Centre floor rear carpet: Removal - Refitting
71A
Equipment required diagnostic tool
Tightening torquesm 2.1 daNm
1
Before carrying out any work on a safety system component, lock the air bag computer using the (diagnostic tool) ( (see 8 , Electrical equipment) ). When this function is activated, all the trigger lines are inhibited and the air bag warning light on the instrument panel lights up continuously (ignition on).
2
seat height adjuster mounting bolts
REMOVAL
WARNING
104145
Unclip the trim (1) . Remove the trim (2) .
Remove: - the front seats (see 75A, Front seat frames and runners, Complete front seat: Removal - Refitting, page 75A-6) (observing the safety instructions),
3
- the centre console( (see Centre console: Removal - Refitting) ,
4
- the rear seats, - the boot carpet (see 71A, Body interior trim, Luggage compartment carpet: Removal - Refitting, page 71A-12) , - the floor storage compartments and flaps( (see Floor flap and storage: Removal - Refitting) ,( (see Underseat flap and storage: Removal - Refitting) .
5 104220
Unclip: - the floor sill lining (3) , - the door sill lining (4) and (5) .
71A-7
BODY INTERIOR TRIM Centre floor rear carpet: Removal - Refitting
71A
6
104150
Unclip: - the rear seats mounting rail trim,
7
- the 12 V supply plate. 104359
Disconnect the connectors.
Unclip the trim (6) and (7) .
8
9
104151
Remove: - the rail mounting bolts (8) , - the rail, - the retaining pins (9) . 104360
Unclip the upper door sill lining.
71A-8
BODY INTERIOR TRIM Centre floor rear carpet: Removal - Refitting
71A
104218
Remove the carpet.
104212
Remove: - the plastic rivets, - the plate.
104214
Remove the clips using the unclipping pliers.
104215
Remove the soundproofing pad.
71A-9
BODY INTERIOR TRIM Centre floor rear carpet: Removal - Refitting
71A
10
104211
Remove the bolt (10) .
104210
Unclip the raised floor support.
Unclip the raised floor.
104217
Partially remove the front carpet.
104216
Remove the carpet from the storage compartments.
71A-10
BODY INTERIOR TRIM Centre floor rear carpet: Removal - Refitting
71A
104213
Remove the centre soundproofing pad.
REFITTING 104209
Unclip the front half-floor.
Torque tighten the seat height adjuster mounting bolts ( 2.1 daNm ) . Proceed in the reverse order to removal.
104221
Unclip the seat connector from the clip. Remove the seat height adjuster mounting bolts.
71A-11
BODY INTERIOR TRIM Luggage compartment carpet: Removal - Refitting REMOVAL
1
104446
Unclip the clips (1) using the unclipping pliers. Remove the boot carpet.
REFITTING Check the clips are secure. Proceed in the reverse order to removal.
71A-12
71A
BODY INTERIOR TRIM Headlining: Removal - Refitting
71A
Special tooling required Car. 1597
Lever for removing rear grab handle clips Equipment required
1
diagnostic tool
IMPORTANT Before carrying out any work on a safety system component, lock the air bag computer using the (diagnostic tool) ( (see 8, Electrical equipment) ). When this function is activated, all the trigger lines are inhibited and the air bag warning light on the instrument panel lights up continuously (ignition on).
REMOVAL
101715
Unclip the upper casing (1) .
Remove: - the windscreen pillar trim (see 71A, Body interior trim, A-pillar trim: Removal - Refitting, page 71A-28) , - the sun visors( (see Sun visor: Removal - Refitting) . Partially remove: - the door frame seals, - the tailgate seal. WARNING The frame seals should be handled carefully to avoid any risk of damage or marking.
2
101716
Unclip the lower casing (2) .
71A-13
BODY INTERIOR TRIM Headlining: Removal - Refitting
3
71A
5
6
101717
104145
Disconnect the connectors.
Unclip the upper section of the trim (5) .
Remove the interior rear-view mirror (3) .
Remove the trim (6) .
When removing the rear-view mirror, be careful not to damage the nearby rain sensor.
7
4
104143
Partially remove the door seals. Unclip the lower retaining clips (7) . 18828
Undo the seat belt by pressing the catch (4) .
71A-14
BODY INTERIOR TRIM Headlining: Removal - Refitting
71A
9 10
13
13
8
104146
Remove:
104360
Unclip the upper door sill lining (13) .
- the trim (8) and (9) , - the seat belt buckle via the aperture (10) .
14 11
104363
12
Unclip the light. 104359
Unclip the trim (11) and (12) .
Disconnect the connector. Remove the three trim mounting bolts (14) . Partially remove: - the tailgate seal, - the rear door seal.
71A-15
BODY INTERIOR TRIM Headlining: Removal - Refitting
71A
104362
Remove the wheel arch interior trim (partially).
103842
Remove: - the plate nut (depending on equipment level).
Note:
- the belt from the rear quarter panel trim.
There is no need to remove the boot carpet, or fully detach the wheel arch interior trim.
17
16
15
15
100183
104361
Unclip the two mounting pins (17) using tool (Car. 1597) . Remove the part, pulling it off by hand from above.
Unclip the trim (15) . Remove the seat belt web via the aperture (16) .
71A-16
BODY INTERIOR TRIM Headlining: Removal - Refitting
71A
104348
103922
Unclip the trim.
18
19
97193
Press on the clip (18) . Remove the trim retaining clips towards the rear (19) . Carefully unclip the trim (this operation requires two people). Fit the trim on the head rests (this operation requires two people). Disconnect the various connectors. Carefully remove the trim via the tailgate to prevent it bending (this operation requires two people).
71A-17
BODY INTERIOR TRIM Headlining: Removal - Refitting
71A
SPECIAL NOTES ON REMOVING THE HEADLINING FROM A ROOF WITH A SUNROOF:
Note: The procedure deals only with components which are present if the vehicle is fitted with a sunroof. The rest of the procedure is the same as for a model without a sunroof.
104352
Connect the connectors (wiring on trim). Centre the trim while fitting the grab handles.
101983
Remove the sunroof switch using unclipping pliers, protecting the trim.
20
Disconnect the connectors. WARNING The trim must be handled carefully because cutting the sunroof makes the two side edges more fragile (risk of bending).
REFITTING Return the trim via the tailgate. 101315
Check the condition of the clips (20) before refitting the trim (part no. 82 00 100 314 ).
WARNING The Carminat aerial wire is attached to the lefthand windscreen pillar mounting clips. Proceed in the reverse order to removal.
71A-18
BODY INTERIOR TRIM Front door sill lining: Removal - Refitting REMOVAL
1
2
104145
Unclip the upper section of the trim (1) . Remove the trim (2) .
3 4
5 104220
Unclip: - the floor sill lining (3) , - the door sill lining (4) and (5) .
REFITTING Proceed in the reverse order to removal.
71A-19
71A
BODY INTERIOR TRIM B-pillar lower trim: Removal - Refitting REMOVAL Move the front seat forward.
1
2
104145
Unclip the upper section of the trim (1) . Remove the trim (2) .
REFITTING Proceed in the reverse order to removal.
71A-20
71A
BODY INTERIOR TRIM Rear door sill lining: Removal - Refitting REMOVAL Move the front seat forward.
1
2
104145
Unclip the upper section of the trim (1) . Remove the trim (2) .
3
4 104359
Unclip the trim (3) and (4) .
REFITTING Proceed in the reverse order to removal.
71A-21
71A
BODY INTERIOR TRIM Rear door sill lining: Removal - Refitting
71A
LONG CHASSIS
REMOVAL Tilt the second row seat.
107111
Partially unclip the rear inner sill lower trim. 107108
Unclip the rear inner sill upper trim.
REFITTING Proceed in the reverse order to removal.
1
107110
Remove: - the parcel shelf mounting bolts (1) , - the parcel shelf.
71A-22
BODY INTERIOR TRIM C-pillar lower trim: Removal - Refitting
71A
Equipment required diagnostic tool
REMOVAL IMPORTANT Before carrying out any work on a safety system component, lock the air bag computer using the (diagnostic tool) ( (see 8 , Electrical equipment) ). When this function is activated, all the trigger lines are inhibited and the air bag warning light on the instrument panel lights up continuously (ignition on).
3
Move the front seat forward.
4 104359
Unclip the trim (3) and (4) .
1 5
2
5
104145
Unclip the upper section of the trim (1) . Remove the trim (2) . 104360
Unclip the upper door sill lining (5) .
REFITTING Proceed in the reverse order to removal.
71A-23
BODY INTERIOR TRIM Rear wheel arch lining: Removal - Refitting
71A
Equipment required diagnostic tool
REMOVAL IMPORTANT Before carrying out any work on a safety system component, lock the air bag computer using the (diagnostic tool) ( (see 8 , Electrical equipment) ). When this function is activated, all the trigger lines are inhibited and the air bag warning light on the instrument panel lights up continuously (ignition on).
3
Move the front seat forward.
4 104359
Unclip the trim (3) and (4) .
1 5
5
2
104145
Unclip the upper section of the trim (1) . Remove the trim (2) . 104360
Unclip the upper door sill lining (5) .
71A-24
BODY INTERIOR TRIM Rear wheel arch lining: Removal - Refitting
71A
REFITTING Proceed in the reverse order to removal.
6
104363
Unclip the light. Disconnect the connector. Remove: - the three trim mounting bolts (6) , - the boot carpet. Partially remove: - the tailgate seal, - the rear door seal.
104362
Remove the wheel arch interior trim.
71A-25
BODY INTERIOR TRIM Rear wheel arch lining: Removal - Refitting
71A
LONG CHASSIS
REMOVAL
107111 107119
Remove:
Tilt the rear seat. Partially unclip the rear inner sill lower trim.
- the boot storage compartments, - the trims, - the rear end panel trim ( (see 71A, Body interior trim) ).
1 107108
Unclip the rear inner sill upper trim.
107110
Remove: - the bolts (1) , - the parcel shelf.
71A-26
BODY INTERIOR TRIM Rear wheel arch lining: Removal - Refitting LONG CHASSIS
2
107107
Remove the boot light (2) . Disconnect the light connector.
107107
Remove the wheel arch trim.
REFITTING Proceed in the reverse order to removal.
71A-27
71A
BODY INTERIOR TRIM A-pillar trim: Removal - Refitting REMOVAL
71A
REFITTING
Note: The seals should be handled carefully to prevent any risk of damage or marking.
3
1
2 101315
Check the condition of the clips (3) before refitting the trim (part no.: 82 00 100 314 ). WARNING 104050
Partially remove the seal. Unclip the trim (1) and (2) .
The Carminat aerial wire is attached to the lefthand windscreen pillar mounting clips. Proceed in the reverse order to removal.
71A-28
BODY INTERIOR TRIM B-pillar upper trim: Removal - Refitting
71A
REMOVAL Move the front seat forward.
1
4 104143
Partially remove the door seals. 18828
Unclip the lower retaining clips (4) .
Undo the seat belt by pressing the catch (1) .
6
7 2
3 5 104145
104146
Unclip the upper section of the trim (2) .
Remove:
Remove the trim (3) . - the trim (5) and (6) , - the seat belt web via the aperture (7) .
REFITTING Proceed in the reverse order to removal.
71A-29
BODY INTERIOR TRIM Rear quarter panel trim: Removal - Refitting
71A
Equipment required diagnostic tool
REMOVAL IMPORTANT Before carrying out any work on a safety system component, lock the air bag computer using the (diagnostic tool) ( (see 8 , Electrical equipment) ). When this function is activated, all the trigger lines are inhibited and the air bag warning light on the instrument panel lights up continuously (ignition on).
3
Move the front seat forward.
4 104359
Unclip the trim (3) and (4) .
1 5
5
2
104145
Unclip the upper section of the trim (1) . Remove the trim (2) . 104360
Unclip the upper door sill lining (5) .
71A-30
BODY INTERIOR TRIM Rear quarter panel trim: Removal - Refitting
71A
6
104363
104362
Unclip the light.
Remove the wheel arch interior trim (partially).
Disconnect the connector. Remove the three trim mounting bolts (6) .
Note:
Partially remove:
There is no need to remove the boot carpet, or fully detach the wheel arch interior trim.
- the tailgate seal, - the rear door seal.
8
7
7
104361
Unclip the trim (7) . Remove the seat belt web via the aperture (8) .
REFITTING Proceed in the reverse order to removal.
71A-31
BODY INTERIOR TRIM Rear quarter panel trim: Removal - Refitting
71A
LONG CHASSIS
Tightening torquesm seat belt mounting bolts
2.1 daNm
REMOVAL
3
Remove the wheel arch trim (see (see 71A, Body interior trim) ).
107104
Remove the belt guide with a flathead screwdriver (3) .
1 1 2
2
107106
Remove: - the bolts (1) , - the seat belt guide.
107240
Remove: - the rear quarter panel trim,
2
- the seat belt web via the aperture.
REFITTING Torque tighten the seat belt mounting bolts ( 2.1 daNm ) . Proceed in the reverse order to removal. 107105
Remove: - the belt bolt cover (2) , - the bolt.
71A-32
BODY INTERIOR TRIM Rear end panel lining: Removal - Refitting REMOVAL
1
104437
Remove the blanking covers (1) .
2
104436
Partially remove the luggage compartment seal. Remove: - the bolts (2) , - the rear end panel trim.
REFITTING Proceed in the reverse order to removal.
71A-33
71A
BODY INTERIOR TRIM Rear end panel lining: Removal - Refitting LONG CHASSIS
REMOVAL
107120
Partially remove the luggage compartment seal.
1
107119
Remove: - the blanking covers, - the bolts, - the rear end panel trim.
REFITTING Proceed in the reverse order to removal.
71A-34
71A
SIDE OPENING ELEMENT LINING Front side door trim: Removal - Refitting
72A
Note: In the event of a door replacement or operation on the bodywork (see 47A, Side opening elements, Front side door ).
REMOVAL
106328
Unclip the window winder plate (at the rear) using the unclipping pliers, for the right-hand door. Disconnect the connector.
103803
Protect the trim (using a mastic knife for example). Unclip the window winder plate (at the front) using the unclipping pliers, for the left-hand door. Disconnect the connectors. Remove the plate.
103930
Unclip the pull handle trim.
72A-1
SIDE OPENING ELEMENT LINING Front side door trim: Removal - Refitting
72A
103929
114171
Remove the storage compartment from its housing.
Remove: - the storage compartment plastic rivet,
WARNING Do not pull on the storage compartment cover.
1
114170
Insert a hand to the base of the storage compartment. 103931
Push your hand towards the interior of the door box section until the storage compartment unclips.
Remove the two pull handle bolts (1) . Unclip the flap with the unclipping pliers (while protecting the lower trim). Remove the flap.
72A-2
SIDE OPENING ELEMENT LINING Front side door trim: Removal - Refitting
72A 5
2 7
6 4
4
105007
103933
Remove:
Remove the door opening control cover and bolt (2) .
- the three bolts (4) , - the trim (5) , (6) and (7) (partially). Disconnect the speaker connector.
3
Unclip the wiring harness from the trim.
REFITTING WARNING If necessary, replace the adhesive sealing foam around the window winder plate connector to ensure it is water-tight.
Note: For replacement, the trim is delivered separately, so remember the wiring harness routing. 105008
Unclip: - the opening control cable mounting cover with a flat-blade screwdriver, - the rear-view mirror adjustment control (3) , - the light. Remove the handle. Disconnect the connectors.
72A-3
Proceed in the reverse order to removal.
SIDE OPENING ELEMENT LINING Front door flap: Removal - Refitting
72A
Note: If replacing a door or carrying out a bodywork operation ( (see 47A, Side opening elements) ).
REMOVAL
106328
Unclip the window winder plate (at the rear) using the unclipping pliers, for the right-hand door. Disconnect the connector.
103803
Unclip the window winder plate (at the front) using the unclipping pliers, for the left-hand door. Disconnect the connector. Remove the plate.
103930
Unclip the pull handle trim.
72A-4
SIDE OPENING ELEMENT LINING Front door flap: Removal - Refitting
72A
REFITTING Proceed in the reverse order to removal.
103929
Remove: - the storage compartment plastic rivet, - the storage compartment. WARNING Do not pull on the glovebox cover.
1
103931
Remove the two pull handle bolts (1) . Unclip the flap with the unclipping pliers (while protecting the lower trim). Remove the flap.
72A-5
SIDE OPENING ELEMENT LINING Rear side door trim: Removal - Refitting
72A
Note: If replacing a door or carrying out a bodywork operation ( (see 47A, Side opening elements) ).
REMOVAL
1
103869
Using a flathead screwdriver, unclip the opening control cable mounting cover.
103868
Remove: - the cover, - the window winder plate bolt, - the plate. Disconnect the connector. Remove:
2
- the cover, - the door opening control bolt (1) .
103870
Unclip the flap with the unclipping pliers (while protecting the lower trim). Remove the flap. Unclip the light (2) with a flathead screwdriver. Disconnect the connector.
72A-6
SIDE OPENING ELEMENT LINING Rear side door trim: Removal - Refitting
6
3
4
5 7 103871
Unclip the sun vi sor (3) (only remove if replacing).
Note: When replacing the visor, do not unwind it before fitting it on the trim; a clip maintains the visor's tension before fitting. Remove: - the bolt (4) , - the bolt (5) , - the trim (6) and (7) (partially). Disconnect the speaker connector. Unclip the wiring harness from the trim.
REFITTING
WARNING If necessary, replace the adhesive sealing foam around the window winder plate connector to ensure it is leaktight.
Note: For replacement, the trim will be delivered separately, so remember the wiring harness routing. Proceed in the reverse order to removal.
72A-7
72A
SIDE OPENING ELEMENT LINING Rear door flap: Removal - Refitting
72A
Note: If replacing a door or carrying out a bodywork operation ( (see 47A, Side opening elements) ).
REMOVAL
1
103869
Using a flathead screwdriver, unclip the opening control cable mounting cover.
103868
Remove: - the cover, - the window winder plate bolt. Disconnect the plate. Disconnect the connector. Remove: - the cover, - the door opening control bolt (1) .
103870
Unclip the flap with the unclipping pliers (while protecting the lower trim). Remove the flap.
72A-8
SIDE OPENING ELEMENT LINING Rear door flap: Removal - Refitting REFITTING WARNING If necessary, replace the adhesive sealing foam around the window winder plate connector to ensure it is leaktight. Proceed in the reverse order to removal.
72A-9
72A
NON-SIDE OPENING ELEMENT LINING Tailgate lining: Removal - Refitting
73A
REMOVING THE TAILGATE TRIM FROM A NON-OPENING REAR SCREEN
1 103545
Unclip the side trim panels. 103542
Unclip the upper trim.
Note: If there is a problem with the rear parcel shelf retaining pin (1) , the pin is available at retail as a spare part, and can be replaced individually.
REMOVING THE TAILGATE TRIM FROM AN OPENING REAR SCREEN
103543
Remove the four centre lower trim bolts. 104514
Unclip:
Unclip the upper trim.
- the lock cover,
Disconnect the light connector.
- the centre trim.
73A-1
NON-SIDE OPENING ELEMENT LINING Tailgate lining: Removal - Refitting
73A
104515
Remove the four centre lower trim bolts. Unclip: - the lock cover, - the centre trim.
104503
Unclip the side trim panels.
Note: If there is a problem with the rear parcel shelf retaining pin, the pin is available at retail as a spare part, and can be replaced individually.
104504
Remove the rams.
104520
Unclip the opening rear screen motor trim.
REFITTING Proceed in the reverse order to removal.
73A-2
NON-SIDE OPENING ELEMENT LINING Bonnet soundproofing: Removal - Refitting REMOVAL
104349
Unclip the clips with the unclipping pliers.
REFITTING Replace the clips if necessary. Proceed in the reverse order to removal.
73A-3
73A
FRONT SEAT FRAMES AND RUNNERS Fixed front seat frame: Removal - Refitting
75A
LONG CHASSIS
Tightening torquesm seat back mounting bolts
25 Nm
seat back mounting nuts
66 Nm
I - REMOVAL Remove: - the complete front seat (see 75A, Front seat frames and runners ) (observe the safety instructions), - the seatback trim (see 77A, Front seat trim, Front seat seatback trim ). - the seat base trim (see 77A, Front seat trim, Front seat base trim ), - the runners (see 75A, Front seat frames and runners, Front seat runners ). 1 - Driver's seat
102164
Remove the back adjustment mechanism cover.
3
1 2
102175
Remove the control cable sheath stops. Drill out the (3) lumbar adjustment mechanism rivet. 102167
Disconnect: - the connector, (1) - the airbag module earth terminal. Drill out the rivet (2) . Remove the airbag.
75A-1
Remove the mechanism.
FRONT SEAT FRAMES AND RUNNERS Fixed front seat frame: Removal - Refitting
75A
LONG CHASSIS
102174
Remove: - the runner adjustment handle mounting bolt, - the handle. Carry out the same operation on the seat back adjusting handle.
102172
Unclip the seatback unlocking linkage. Remove the cable.
Note: When replacing the seatback hinge control adjustment cable: - position the cable, - make sure that the seatback is not in the fully forward position, - keep the cable pressed down (with a wedge) between the sheath stop and the linkage to provide additional clearance, 102173
Remove: - the unlocking control cables, - the front casing.
75A-2
- lock the sheath in place with pliers.
FRONT SEAT FRAMES AND RUNNERS Fixed front seat frame: Removal - Refitting
75A
LONG CHASSIS
4
5
6
102171
102390
Unclip: - the cover,
IMPORTANT
- the cable stop (4) .
Insert a metal rod right through the frame via opening (5) , strapping it in place if necessary. Check that it is secure before carrying out any work. Remove bolts (6) .
IMPORTANT Keep the pin in position when removing the bolts.
75A-3
FRONT SEAT FRAMES AND RUNNERS Fixed front seat frame: Removal - Refitting
75A
LONG CHASSIS
8
7 9
102393
104489
Remove: - the bolts (7) ,
IMPORTANT
- the backrest frame.
Insert a metal rod right through the frame via opening (8) , strapping it in place if necessary. Check that it is secure before carrying out any work.
2 - Passenger seat
Remove the three bolts (9) .
IMPORTANT Keep the pin in position when removing the bolts.
104490
Unclip the side cover.
75A-4
FRONT SEAT FRAMES AND RUNNERS Fixed front seat frame: Removal - Refitting
75A
LONG CHASSIS
11
13
10
10
12
104488
102390
Remove the nuts (10) . IMPORTANT
II - REFITTING
Do not remove the plastic clip at (11) . Check that it is secure before carrying out any work; if in any doubt, insert a pin through the parts of the frames (11) .
Note: The refitting method and the tightening torques of the passenger seat are exactly the same as for the driver's seat.
Hand-tighten the frame mountings. Tighten to torque: - the seat back mounting bolts ( 25 Nm ) (12) , - the seat back mounting nuts ( 66 Nm ) (13) . Cut the plastic clip (11) . Proceed in the reverse order to removal.
75A-5
FRONT SEAT FRAMES AND RUNNERS Complete front seat: Removal - Refitting
75A
Equipment required diagnostic tool
Tightening torquesm front seat inside and outside rear bolts
21 Nm
front seat inside and outside front bolts
21 Nm
battery terminals
12 Nm
1
IMPORTANT - Before any work is carried out on a safety system component, be sure to lock the airbag computer using the (diagnostic tool) (see 88C, Air bags and pretensioners, Air bag computer locking procedure ). When this function is activated, all the trigger lines are disabled and the airbag instrument panel warning light is lit when ignition is switched on.
18828
Undo the seat belt by pressing the catch (1) .
IMPORTANT Handling pyrotechnic systems (airbags or pretensioners) near to a source of heat or flame is forbidden: there is a risk of triggering the air bags and pretensioners.
REMOVAL Disconnect the battery by starting with the positive terminal (see 80A, Battery: Remove and refit ). Protect: - the front door sill lining, - the carpet. 104148
Move the seat to the forward position. Remove the r ear mounting bolts.
75A-6
FRONT SEAT FRAMES AND RUNNERS Complete front seat: Removal - Refitting
75A
Front left-hand seat
4 3
104147
Move the seat to the rear position. Remove the front mounting bolts.
2
1
102189
Pre-tighten the front outside and inside bolts. Move the seat forwards by checking the symmetry of the left and right runner positions. Torque tighten the front seat inside and outside rear bolts ( 21 Nm ) . Move the seat back. Torque tighten the front seat inside and outside front bolts ( 21 Nm ) .
WARNING Connect the battery, starting with the positive terminal; carry out the necessary programming (see 80A, Battery: Remove and refit ). 104149
Torque tighten the battery terminals ( 12 Nm ) .
Disconnect the connector under the seat. Remove the seat (this operation requires two people).
REFITTING Position and lock the seat at the rear before refitting it in the vehicle. WARNING Observe the tightening order for the seat bolts.
75A-7
IMPORTANT Unlock the air bag computer using the (diagnostic tool) (see 88C, Airbags and pretensioners, Airbag computer locking procedure).
FRONT SEAT FRAMES AND RUNNERS Front seat runner: Removal - Refitting
75A
Driver's seat right-hand runner Tightening torquesm seat runner mounting bolts
21 Nm
REMOVAL Remove the whole front seat (see 75A, Front seat frames and runners, Complete front seat ), (observe the safety instructions). Driver's seat left-hand runner
2
102395
Remove the three bolts (2) .
REFITTING Torque tighten the seat runner mounting bolts ( 21 Nm ) . Proceed in the reverse order to removal.
1
102394
Remove the two nuts (1) .
75A-8
REAR SEAT FRAMES AND RUNNERS Complete rear seat: Removal - Refitting
76A
Tightening torquesm "frame and runner" assembl y mounting bolts
25 Nm
I - REMOVAL Remove: - the seat from the vehicle, - the head rest. 1 - Side rear seat
3 2 103529
Remove: - the bolts (3) , - the stalk
1
5
110831
Remove the seatback cover trim. Unclip the clips (1) . Remove the seat belt guide (2) .
4
103527
Remove: - the bolt (4) , - the stalk. Unclip: - the blanking cover (5) , - the seatback unlocking control.
76A-1
REAR SEAT FRAMES AND RUNNERS Complete rear seat: Removal - Refitting
76A
6 8
103524
Remove the clips (6) using the unclipping pliers.
110835
Slightly lift the plastic casing. Unclip the hook cover securing straps (8) .
7
103523
Drill out rivets (7) .
103525
Remove the inside cover retaining strips.
76A-2
REAR SEAT FRAMES AND RUNNERS Complete rear seat: Removal - Refitting
103521
76A
103519
Remove the side cover retaining strips. WARNING Carefully remove the cover, holding the foam's velcro strips in place to avoid damaging the seat base foam. Remove: - the seat base cover, - the foam.
103520
Fold the seat base cover forward.
9
103518
Tilt back the seatback. Pull out the zip fastener ends (9) .
76A-3
REAR SEAT FRAMES AND RUNNERS Complete rear seat: Removal - Refitting
103516
103517
Remove the seatback foam. WARNING Carefully remove the cover, holding the foam's velcro strips in place to avoid damaging the seatback foam. Remove the seatback cover as far as the head rest guides.
10
103515
Press onto the clips (10) to remove the head rest guides. Remove the seatback cover.
76A-4
76A
REAR SEAT FRAMES AND RUNNERS Complete rear seat: Removal - Refitting
76A
2 - Special features of the central rear seat seatback trim
104676 104674
Unclip: - the retaining strips, - the head rest guides.
104675
Unclip the casing using a flat-blade screwdriver.
104677
Note: The casing mounting clips can be seen in the diagram above.
WARNING Carefully remove the cover, holding the foam's velcro strips in place to avoid damaging the seatback foam. Remove the seatback cover.
76A-5
REAR SEAT FRAMES AND RUNNERS Complete rear seat: Removal - Refitting
76A
11
104679
104681
Unclip the hook cover securing straps (11) .
Remove the seat base foam.
104682
Remove: - the seat belt stalk mounting nuts, - the nuts. 104680
II - REFITTING WARNING
Proceed in the reverse order to removal.
Carefully remove the cover, holding the foam's velcro strips in place to avoid damaging the seat base foam.
Torque tighten the "frame and runner" assembly mounting bolts ( 25 Nm ) .
Remove the seat base cover. WARNING Before refitting the covers, check that that velcro strips on the seatback foam and the seat base foam are holding.
76A-6
REAR SEAT FRAMES AND RUNNERS Second row complete rear seat: Removal - Refitting
76A
LONG CHASSIS
Tightening torquesm
Note:
seat bolts
21 Nm
seat support bolts
21Nm
stalk bolts
21Nm
centre stalk bolts
44 Nm
If a seat is locked, unlock it using a locally made hook to manipulate the linkage (1) under the seat, or the opening control support (2) .
REMOVAL SPECIAL FEATURES OF THE SECOND ROW OF REAR SEATS
Unlocking the second row rear seat.
107117
Remove: - the boot storage compartments, - the trims (see 71A, Body internal trim ).
107114
2 1
107326
76A-7
REAR SEAT FRAMES AND RUNNERS Second row complete rear seat: Removal - Refitting
76A
LONG CHASSIS
3 5
107100
Lift up the seat without locking it. Remove the bolts (5) . Take the seat out of the vehicle. 107114
Remove:
Remove the wheel arch trim (see 71A, Body internal trim, Wheel arch trim ).
- the bolt (3) , - the seat belt stalks.
6
4 107101
Remove: - the bolt (6) , - the side stalk.
107112
Remove: - the bolts (4) , - the seat belt stalk support.
76A-8
REAR SEAT FRAMES AND RUNNERS Second row complete rear seat: Removal - Refitting
76A
LONG CHASSIS
9
7
107102
107124
Remove the bolt (9) .
Remove: - the bolts (7) , - the support.
10
107124
Move the wiring harness to one side. Remove: - the starting aerial (10) ,
107124
- the seat front support.
Partially remove the carpet.
REFITTING ADJUSTMENT PROCEDURE FOR THE REAR SEATS, SECOND ROW Screw in and tighten, with the seats in folded position. Hand-tighten the bolts (8) and (9) for the rear seat front support.
8
Pull the front support of the seats back as far as it will go. Open and lock the seats. 107124
Make sure the seats are completely locked. Tighten the left-hand bolt (8) of the front support.
Remove the bolts (8) .
76A-9
REAR SEAT FRAMES AND RUNNERS Second row complete rear seat: Removal - Refitting LONG CHASSIS Tighten the right-hand bolt (8) of the front support. Tighten the central bolt (9) of the front support. Refit the front support long bolt. Tighten to torque: - the seat bolts ( 21 Nm ) , - the seat support bolts ( 21Nm ) , - the stalk bolts ( 21Nm ) , - the centre stalk bolts ( 44 Nm ) . Carry out a function test. Proceed in the reverse order to removal.
76A-10
76A
REAR SEAT FRAMES AND RUNNERS Second row rear seat frame: Removal - Refitting LONG CHASSIS
REMOVAL Remove the seat trim (see 76A, Rear seat frames and runners, Second row rear seat trim).
1
107131
Remove: - the bolt (1) , - the hinge.
107132
Remove the frame grille.
REFITTING Proceed in the reverse order to removal.
76A-11
76A
REAR SEAT FRAMES AND RUNNERS Rear side seat mechanism: Removal - Refitting
76A
LONG CHASSIS
Tightening torquesm bolts
14 Nm
REMOVAL
107347
Remove the return spring using pliers.
1
4 107348
Unclip the cover (1) .
2
107344
Remove the clip (4) .
3
107343
Remove: - the ram pin (2) , - the clip (3) .
76A-12
REAR SEAT FRAMES AND RUNNERS Rear side seat mechanism: Removal - Refitting
76A
LONG CHASSIS
7
5 107122
107323
Remove the clip (5) .
Remove the locking control linkage (7) .
8
6
107345
107346
Remove the locking control bar (6) .
Remove the bolts (8) .
REFITTING Torque tighten the bolts ( 14 Nm ) . Note: Carry out an operating check on the vehicle, before refitting the runner on the frame. Proceed in the reverse order to removal.
76A-13
REAR SEAT FRAMES AND RUNNERS Rear central seat runners: Removal - Refitting
76A
LONG CHASSIS
Tightening torquesm runner mounting bolts
25 Nm
REMOVAL
3 107382
Remove the casing mounting bolts (3) .
1
107385
4
Remove the three retaining strips (1) .
107383
Remove the casing (4) .
2
5 2
107386
Remove: - the seat trim partially,
107384
- the runner nuts (2) .
Remove the mounting bolts (5) .
76A-14
REAR SEAT FRAMES AND RUNNERS Rear central seat runners: Removal - Refitting LONG CHASSIS
REFITTING Remove the « runner-mechanism » assembly from the frame. Note: Carry out an operating check on the vehicle, before refitting the runner on the frame. Torque tighten the runner mounting bolts ( 25 Nm ). Proceed in the reverse order to removal.
76A-15
76A
REAR SEAT FRAMES AND RUNNERS Rear seat runner: Removal - Refitting
76A
SPECIAL FEATURE OF THE REAR CENTRAL SEAT RUNNERS Tightening torquesm "frame and runner" assembl y mounting bolts
25 Nm
REMOVAL Remove the rear seat base trim (see 78A, Rear seat trim, Seatback trim ).
104682
Remove: - the seat belt stalk mounting nuts, - the nuts.
2 1
1 103514
Remove the "frame and runner" assembly mounting nuts.
103512
Remove the casing (1) and (2) .
REFITTING Torque tighten the "frame and runner" assembly mounting bolts ( 25 Nm ) . Proceed in the reverse order to removal.
76A-16
FRONT SEAT TRIM Front seatback trim: Removal - Refitting
77A
LONG CHASSIS Special tooling required Car. 1597
Lever for removing rear grab handle clips
Car. 1558
Pliers for zip fasteners
REMOVAL Remove: - the whole front seat (see 75A, Front seat frames and runners, Complete front seat ), (observe the safety instructions). - the head rest.
1
102184
Remove the casing bolt (1) .
110749
Note:
2
Protect the lift command handle (using masking tape), give a light tap with a mallet (on the rear section of the command), keeping the command slightly lifted.
102185
Remove: - the casing bolt (2) , - the casing.
77A-1
FRONT SEAT TRIM Front seatback trim: Removal - Refitting
77A
LONG CHASSIS
3
102177
Remove the back adjustment tumblewheel mounting cover, using tool (Car. 1597) .
102179
Remove: - the cover rubber bands (3) , - the cover flap.
4
102178
Remove the back adjustment tumblewheel using a screwdriver.
104479
Remove: - the four parcel shelf mounting rivets (4) , - the parcel shelf.
77A-2
FRONT SEAT TRIM Front seatback trim: Removal - Refitting
77A
LONG CHASSIS
5 6
110834
Unclip the trim (5) and (6) .
102189
Remove the seatback cover lower retaining rubber bands.
7
102188 102183
Unclip the cover clips from the air bag. Remove the cover retaining strips (7) .
77A-3
FRONT SEAT TRIM Front seatback trim: Removal - Refitting
77A
LONG CHASSIS
9
102187
110833
Unclip the head rest (9) guides. WARNING Carefully remove the cover, holding the foam's velcro strips in place to avoid damaging the seatback foam.
8 102191
Remove the seatback foam.
110832
Partially remove (8) the felt.
77A-4
FRONT SEAT TRIM Front seatback trim: Removal - Refitting
77A
LONG CHASSIS
11
10
102192
Remove the backrest frame felt.
104478
Remove the bolt (10) . Unclip the handle (11) .
SPECIAL FEATURES OF THE PASSENGER SEAT
12
104476 104477
Unclip the blanking cover.
77A-5
Remove the casing bolt (12) .
FRONT SEAT TRIM Front seatback trim: Removal - Refitting
77A
LONG CHASSIS
15 16
13
104475
Unclip the trim (13) .
110834
Unclip the trim (15) and (16) .
Remove the casing.
14
104484 104479
Remove: - the four parcel shelf mounting rivets (14) , - the parcel shelf.
77A-6
Undo the zip fastener.
FRONT SEAT TRIM Front seatback trim: Removal - Refitting
77A
LONG CHASSIS
17 18
104485
Disconnect the heating mat (17) connector (depending on equipment level).
110832
Partially remove the felt (18) .
19
110833 104481
Unclip the cover from the air bag.
Unclip the head rest guides (19) . Remove the cover and the seatback foam.
WARNING Carefully remove the cover, holding the foam's velcro strips in place to avoid damaging the seatback foam.
77A-7
FRONT SEAT TRIM Front seatback trim: Removal - Refitting LONG CHASSIS
REFITTING Proceed in the reverse order to removal. WARNING Before refitting the seatback cover, check that the velcro strips are properly fastened to the seatback foam. SPECIAL FEATURES OF THE PASSENGER SEAT Refit the cover zip fastener using tool (Car. 1558) (blue in colour).
77A-8
77A
FRONT SEAT TRIM Front seat base trim: Removal - Refitting
77A
LONG CHASSIS
REMOVAL Remove the whole front seat (see 75A, Front seat frames and runners, Complete front seat ), (observe the safety instructions).
2
102185
Remove: - the casing bolt (2) , 110749
- the casing
Note: Protect the lift command handle (using masking tape), give a light tap with a mallet (on the rear section of the command), keeping the command slightly lifted.
3
102179
Remove: - the cover (3) rubber bands,
1
- the cover flap.
102184
Remove the casing bolt (1) .
77A-9
FRONT SEAT TRIM Front seat base trim: Removal - Refitting
77A
LONG CHASSIS
6
5
6
102189
Remove the seatback cover lower retaining rubber bands.
102181
Remove: - the clip (5) , - the cover retaining strips (6) .
4
7
102183
Remove the seatback cover retaining strips (4) . 102180
Remove the cover retaining strip (7) .
WARNING Carefully remove the cover, holding the foam's velcro strips in place to avoid damaging the seat base foam.
77A-10
FRONT SEAT TRIM Front seat base trim: Removal - Refitting
77A
LONG CHASSIS SPECIAL FEATURES OF THE PASSENGER SEAT
9 102190 104476
Remove: Remove the casing bolt (9) .
- the seat base cover, - the foam.
8 10 102182
Remove the cover clips (8) . 104475
Unclip the trim (10) . Remove the casing.
77A-11
FRONT SEAT TRIM Front seat base trim: Removal - Refitting
77A
LONG CHASSIS
11
12 11 104482
104486
Remove:
Remove the seat base cover.
- the seat base cover retaining rubber band,
Remove the seat base foam.
- the retaining strips (11) . WARNING
Disconnect the heating mat connector (12) (depending on equipment level).
Carefully remove the cover, holding the foam's velcro strips in place to avoid damaging the seat base foam.
REFITTING WARNING Before refitting the seatback cover, check that the velcro strips are properly fastened to the seat base foam.
Note: To replace the seat base cover, carefully cut out the ISOFIX label for the driver' seat only, without damaging the seat base. Proceed in the reverse order to removal.
77A-12
REAR SEAT LINING Rear seatback trim: Removal - Refitting
78A
LONG CHASSIS I - REMOVAL Remove: - the seat from the vehicle, - the head rest.
2
1 103516
WARNING
110831
Carefully remove the cover, holding the foam's velcro strips in place to avoid damaging the seatback foam.
Remove the seatback cover trim. Remove the seatback cover as far as the head rest guides.
Unclip the clips (1) . Remove the seat belt guide (2) .
4
3
103515 103518
Tilt back the seatback.
Press onto the clips (4) to remove the head rest guides.
Pull out the zip fastener ends (3) .
Remove the seatback cover.
78A-1
REAR SEAT LINING Rear seatback trim: Removal - Refitting
78A
LONG CHASSIS II - SPECIAL FEATURES OF THE CENTRAL REAR SEAT SEATBACK TRIM
103517
Remove the seatback foam. 104674
104675
Unclip the casing using a flat-blade screwdriver.
Note: The casing mounting clips can be seen in the diagram above.
78A-2
REAR SEAT LINING Rear seatback trim: Removal - Refitting
78A
LONG CHASSIS III - REFITTING Proceed in the reverse order to removal.
WARNING Before refitting the seatback cover, check that the velcro strips are properly fastened to the seatback foam pad.
104676
Unclip: - the retaining strips, - the head rest guides.
104677
WARNING Carefully remove the cover, holding the foam's velcro strips in place to avoid damaging the seatback foam. Remove the seatback cover.
78A-3
REAR SEAT LINING Second row rear seat trim: Removal - Refitting
78A
LONG CHASSIS
REMOVAL Remove: - the seat (see 76A, Rear seat frame and runners, Complete rear seat), - the head restraint.
107338
1 WARNING Carefully remove the seatback cover, to avoid damaging the mounting clips.
107328
Remove the control belt (1) .
3
2
4
107331
Remove the clips (4) .
107125
Remove the backrest casing with a flathead screwdriver, carrying out the operations indicated (2) and (3) , in order.
78A-4
REAR SEAT LINING Second row rear seat trim: Removal - Refitting
78A
LONG CHASSIS
6
5 7
107332
Remove:
7
107381
Partially remove the seatback « foam-cover » assembly.
- the retaining strips (5) , - the velcro strip (6) .
WARNING Carefully remove the head rest guides, pressing on the tabs (7) .
107333
Extract the head rest guides. 107329
Remove the cover retaining strips.
78A-5
REAR SEAT LINING Second row rear seat trim: Removal - Refitting
78A
LONG CHASSIS
107330
Remove the cover retaining rubber bands.
107335
Turn the hinges.
9
8 107334
Remove the bolts (8) .
107336
Remove: - the retaining strips (9) , - the « foam-cover » assembly.
78A-6
REAR SEAT LINING Second row rear seat trim: Removal - Refitting
78A
LONG CHASSIS
107325
107324
Extract the seat base foam.
Take out the seatback foam from the cover.
WARNING
WARNING
Carefully remove the cover, holding the foam's velcro strips in place to avoid damaging the seat base foam.
Carefully remove the cover, holding the foam's velcro strips in place to avoid damaging the seatback foam.
REFITTING Proceed in the reverse order to removal.
107341
Thread the release belt through the cover rubber band.
78A-7
REAR SEAT LINING Second row rear seat trim: Removal - Refitting
78A
LONG CHASSIS
10
107340
107342
Thread the belt through the seatback casing, and clip the seatback casing back on.
Thread the belt through the cover rubber band (10) .
107328 107338
WARNING Carefully clip the seatback cover back on, to avoid damaging the mounting clips.
78A-8
Secure the locking belt on the support.
REAR SEAT LINING Rear side seat trim: Removal - Refitting
78A
Special tooling required Car. 1558
Pliers for zip fasteners
Tightening torquesm stalk mounting bolts
25 Nm
frame-runners mounting nuts
25 Nm
REMOVAL Remove the headrest.
103531
Unclip the seat belt guide lower trim with a screwdriver (1) .
103530
Unclip the upper trim from the seat belt guide.
103529
Remove the seat belt stalk mounting bolt.
78A-9
REAR SEAT LINING Rear side seat trim: Removal - Refitting
78A
103527
Remove:
103525
Remove the seat base cover retaining strips.
- the seat back unlocking control blanking cover with a screwdriver, - the seat belt stalk mounting bolt.
Note: There are two different models of seat base casing and seat cover.
103526
Remove the seatback unlocking control. 114092
Cover fixed over the base casing (2) .
78A-10
REAR SEAT LINING Rear side seat trim: Removal - Refitting
78A
114091
114094
Cover fixed beneath the base casing (3) .
If these four holes are not present, the cover is fixed beneath the base casing.
The base casings are different depending on the model.
COVER FIXED OVER THE BASE CASING
114095
If these four holes are present, the cover is fixed over the base casing.
78A-11
103524
Remove the clips using unclipping pliers (5) .
REAR SEAT LINING Rear side seat trim: Removal - Refitting
103523
Remove the rivets (6) .
114087
Remove the base casing at (8) .
COVER FIXED BENEATH THE BASE CASING
114093
Remove the rivets (7) .
78A-12
78A
REAR SEAT LINING Rear side seat trim: Removal - Refitting
78A
114090
103522
Remove the cover retaining rubber bands.
114088
Remove cover retaining strips at (9) .
103521
Remove the cover retaining strips.
78A-13
REAR SEAT LINING Rear side seat trim: Removal - Refitting
103520
Fold the seat cushion cover forward.
78A
103518
Pull out the ends of the zip fastener with a screwdriver. Undo the zip fastener.
103519
Remove: 103516
- the seat cushion cover, Remove the seatback cover as far as the headrest guides.
- the foam.
WARNING Carefully remove the cover, holding the foam's Velcro strips in place to avoid damaging the seat base foam.
WARNING Carefully remove the cover, holding the foam's Velcro strips in place to avoid damaging the seatback foam.
78A-14
REAR SEAT LINING Rear side seat trim: Removal - Refitting
78A
103515
103513
Press on the headrest guide clips to unclip them.
Remove the « frame - runners » assembly mounting nuts.
Remove the « cover - guides » assembly.
Remove the seat base cover.
103517 103512
Remove the foam. Remove the casing (10) and (11) .
REFITTING Refit the cover zip fastener using tool (Car. 1558) (blue in colour). Tighten to torque: - the stalk mounting bolts ( 25 Nm ) , - the frame-runners mounting nuts ( 25 Nm ) .
78A-15
REAR SEAT LINING Rear side seat trim: Removal - Refitting Proceed in the reverse order to removal.
78A-16
78A
REAR SEAT LINING Rear centre seat trim: Removal - Refitting
78A
REMOVAL
104675 104674
Unclip the casing with a screwdriver. Note: The casing mounting clips can be seen in the diagram below.
1
104676
Remove: - the clips (1) , - the retaining strips, - the head rest guides.
78A-17
REAR SEAT LINING Rear centre seat trim: Removal - Refitting
104677
78A
104680
Remove the seat base cover.
Remove: - the seatback cover,
WARNING
- the foam.
Carefully remove the cover, holding the foam's velcro strips on the in place to avoid damaging the seat base foam.
WARNING Carefully remove the cover, holding the foam's velcro strips in place to avoid damaging the seatback foam.
2
104681
Remove the seat base foam.
104679
Cut off the clips (2) from the cover retaining rubber bands.
78A-18
REAR SEAT LINING Rear centre seat trim: Removal - Refitting
104682
Remove: - the seat belt stalk mounting nuts, - the nuts.
REFITTING Proceed in the reverse order to removal.
78A-19
78A
REAR SEAT LINING Rear seat base trim: Removal - Refitting
78A
LONG CHASSIS I - REMOVAL 1 - Side rear seat
3
2
1
103527
Remove: - the stalk (2) bolt, 103529
- the stalk.
Remove:
Unclip:
- the stalk (1) bolt,
- the blanking cover (3) ,
- the stalk.
- the seatback unlocking control.
4
103524
Remove the clips (4) using the unclipping pliers.
78A-20
REAR SEAT LINING Rear seat base trim: Removal - Refitting
78A
LONG CHASSIS
5
103523
Drill out rivets (5) .
103525
Remove the inside cover retaining strips.
6
110835
Slightly lift the plastic casing.
103521
Remove the side cover retaining strips.
Remove the cover retaining (6) elastic straps.
78A-21
REAR SEAT LINING Rear seat base trim: Removal - Refitting
78A
LONG CHASSIS 2 - Central rear seat
7
103520 104679
Fold the seat base cover forward.
Cut off the clips (7) from the cover retaining rubber bands.
103519 104680
WARNING WARNING
Carefully remove the cover, holding the foam's velcro strips in place to avoid damaging the seat base foam.
Carefully remove the cover, holding the foam's velcro strips in place to avoid damaging the seat base foam.
Remove: Remove the seat base cover. - the seat base cover, - the foam.
78A-22
REAR SEAT LINING Rear seat base trim: Removal - Refitting LONG CHASSIS II - REFITTING Proceed in the reverse order to removal.
WARNING Before refitting the seatback cover, check that the velcro strips are properly fastened to the seatback foam pad.
78A-23
78A
View more...
Comments
