Qmatic Wiring Information CTS
December 9, 2016 | Author: jweindel | Category: N/A
Short Description
Download Qmatic Wiring Information CTS...
Description
Information Guide Qmatic Service Technicians Qmatic Wiring Information
Qmatic Corporation 95 Underwood Road Fletcher, NC 28732 Ph: 800.852.6768 Fax: 828.209.1100
Qmatic Wiring Information Guide
TABLE OF CONTENTS HELPFUL INFORMATION ............................................................................................................. 3 TESTING ............................................................................................................................................. 5 TESTING ............................................................................................................................................. 5 Wire Testing ....................................................................................................................................... 5 Information Cable ......................................................................................................................... 5 Voltage Between Wire No. 2(-) and Wire No. 1(+) ...................................................................... 5 Voltage Between Wire No. 2(-) and Wire No. 3 (Output Signal) .................................................. 5 Voltage Between Wire No. 2(-) and Wire No. 4 (Input signal) ..................................................... 5 LAYOUTS ........................................................................................................................................... 7 General Layout ................................................................................................................................... 7 Specific Wiring .................................................................................................................................. 9 Standardized Wire Labelling Scheme ......................................................................................... 10 Connecting Multiple Connection Boxes .......................................................................................... 11 DEVICE WIRING ............................................................................................................................ 12 Multiple Device Connection ............................................................................................................ 12 Interface Wiring ............................................................................................................................... 13 BP Printer Wiring ............................................................................................................................. 15 Keypad Wiring ................................................................................................................................. 17 Display Wiring ................................................................................................................................. 19 Old Display Wiring .......................................................................................................................... 21 Voice Unit Wiring ............................................................................................................................ 23 Old Voice Unit Wiring ..................................................................................................................... 25 Video Unit Wiring............................................................................................................................ 27 Qmatic Monitor Wiring.................................................................................................................... 29
Page 2 of 29
Qmatic Wiring Information Guide
HELPFUL INFORMATION QMATIC SUITE User Type
User Login
User Password
Administrator:
admin
admin
Installer:
install
install
Database User:
qsuite
qsuite
Default Port:
80 or 8080
User Login
User Password
admin
admin
Default Port:
8080 or 8081
QMATIC MANAGEMENT PORTAL (QMMP) User Type Administrator:
SQL 1
During installation, define the “sa” user or master password as:
2
Verify that the database is set up in mixed mode authentication. This means that it can accept Windows logins or SQL user/password logins.
3
Ensure TCP/IP is enabled and port 1433 is enabled for 0 connections MAX.
Page 3 of 29
Qmatic123
Qmatic Wiring Information Guide
Q-WIN Troubleshooting Starting Issues
1
Check that port 80 is not is use. If you cannot use it or if Qwin and QSuite are on the same server, set Q-Win to use port 82.
2
Check for power to the interface.
3
Is Java installed? Is it the correct version? If not, uninstall the current version of java and reinstall QWin. Q-Win will install a working version of java.
4
Check if an antivirus program is preventing the Q-Win service from starting.
5
Verify that the license matches the interface serial.
6
If getting a “C++” error, turn off DEP for the QWIN.EXE. Go to Control Panel Æ System Æ Advanced Æ Performance Æ Settings Æ Data Execution Prevention. Make QWIN.EXE an exception. This will require a restart.
Page 4 of 29
Qmatic Wiring Information Guide
TESTING Wire Testing IMPORTANT!! All cables should be securely fastened within 6” of the termination device. Information Cable Most units are connected to Qmatic systems with a cable of 4 single core wires (24 AWG) in the mains (should this read “main?”) lead. All units are connected parallel. Wire No. 1 Power Supply to each unit (+):
[solid white/green stripe]
Wire No. 2 Ground (-):
[solid green/white stripe]
Wire No. 3 Output Signal:
[solid white/orange stripe]
Wire No. 4 Input Signal:
[solid orange/white stripe]
Displays are normally connected to the system with modular cables via a Satellite Box.
Voltage Between Wire No. 2(-) and Wire No. 1(+) •
Normal = 27-28 V
•
Lowest = 22 V
•
Not under (Is this correct terminology? Would “Not to dip below” be acceptable?) = 20 V
Voltage Between Wire No. 2(-) and Wire No. 3 (Output Signal) This signal pulses between 0 V and the Voltage established at Wire No. 1 (= Terminal Pin No. 1; Power Supply). Depending on the type of Voltage meter used, the reading can differ slightly, but should still be between 18-24 V. The voltage should never be under 10 V, which indicates that somewhere in the system, either the polarities have been mixed up, or one or more units have been damaged.
Voltage Between Wire No. 2(-) and Wire No. 4 (Input signal) This signal pulses between 0 V and the Voltage established at Wire No. 1 (Terminal Pin No. 1; Power Supply).
Page 5 of 29
Qmatic Wiring Information Guide
The Voltage should never be under 10 V, which indicates that somewhere in the system, the polarities have been mixed up or one or more units have been damaged. Proper wiring ensures that a reliable function of the system is achieved. Two problems may arise when the number of units increases. 1. The first problem has to do with the total current consumption of the cable. When the current rises as more units are added, and the length of the cable is more than 50 m, the voltage drops in the cable. The voltage should not get below 20 V between Wire No. 1 and Wire No. 2. The failure can be seen as flickering figures, poor key response, etc. 2. The second problem is due to the capacitance (electrical transfer) between the wires in the cable. This problem only occurs when the total length of all cables is more than 1000 m or when a multi-core wire is used.
Page 6 of 29
Qmatic Wiring Information Guide
LAYOUTS General Layout IMPORTANT!! All cables should be securely fastened within 6” of the termination device.
Page 7 of 29
Qmatic Wiring Information Guide
Figure 1 – General Layout Diagram of the Home Area
Page 8 of 29
Qmatic Wiring Information Guide
Specific Wiring IMPORTANT!! All cables should be securely fastened within 6” of the termination device.
Each power rail of the Power Connection box can only handle a load of 6 amps MAX. Verify that the combined amperage of the wiring on this rail is 6 Amps or less
Figure 2 – Specific Wiring Diagram of the Home Area
Page 9 of 29
Qmatic Wiring Information Guide
The Blue and Brown pairs can be used to provide additional current or they can be used for accessories such as the doorbell, etc.
Standardized Wire Labelling Scheme MD1, MD2, … MDx MD1A, MD1B, … MD1x MD2A, MD2B, … MD2x CD1-x, CD+1-y BP1, BP2, … BPx KT1-x, KTx+1-y SPK1, SPK2, … SPKx INF1, INF2, … INFx PC VOX1, VOX2, … VOXx MLT1, MLT2, … MLTx
Main Displays (NON-TIERED) Main Displays (TIERED): Letter for each wire on a multi-tiered display Counter Displays (Labelled to reflect the display numbers attached to wire) BP Printer Keypads (Labelled to reflect the display numbers attached to wire) Speakers Information Display Q-Win Voice Unit Multi-Interface
Page 10 of 29
Qmatic Wiring Information Guide
Connecting Multiple Connection Boxes IMPORTANT!! All cables should be securely fastened within 6” of the termination device.
Figure 3 – Connecting Multiple Main Connection Boxes Diagram
Page 11 of 29
Qmatic Wiring Information Guide
DEVICE WIRING Multiple Device Connection IMPORTANT!! All cables should be securely fastened within 6” of the termination device.
Figure 4 - Connecting Multiple Devices to One Main Cable from Home Area Diagram
Page 12 of 29
Qmatic Wiring Information Guide
Interface Wiring IMPORTANT!! All cables should be securely fastened within 6” of the termination device.
Figure 5 – Wiring the Interface Diagram
Page 13 of 29
Qmatic Wiring Information Guide
Figure 6 – Wiring the Interface Picture (arrows in pic off)
Page 14 of 29
Qmatic Wiring Information Guide
BP Printer Wiring IMPORTANT!! All cables should be securely fastened within 6” of the termination device.
Figure 8 – Wiring the BP Printer Diagram
Page 15 of 29
Qmatic Wiring Information Guide
Figure 9 – Wiring the BP Printer Picture
Page 16 of 29
Qmatic Wiring Information Guide
Keypad Wiring To ID the keypad, first press the “ALT” key while simultaneously plugging in the power. Next, press the “NEXT” key or “CLOSE” key to increase or decrease the ID number. Unit will save setting after a few seconds. IMPORTANT!! All cables should be securely fastened within 6” of the termination device.
Figure 11 –Wiring the Keypad Diagram
Page 17 of 29
Qmatic Wiring Information Guide
Figure 12 – Wiring the Keypad Picture
Page 18 of 29
Qmatic Wiring Information Guide
Display Wiring IMPORTANT!! All cables should be securely fastened within 6” of the termination device.
Figure 14 – Wiring the LED Display Diagram
Page 19 of 29
Qmatic Wiring Information Guide
Figure 15 – Wiring the LED Display Picture
Figure 16 – Wiring a Doorbell Picture
Page 20 of 29
Qmatic Wiring Information Guide
Old Display Wiring IMPORTANT!! All cables should be securely fastened within 6” of the termination device.
Figure 18 – Wiring Old Displays Diagram
Page 21 of 29
Qmatic Wiring Information Guide
Figure 19 – Wiring Old Displays Picture
Page 22 of 29
Qmatic Wiring Information Guide
Voice Unit Wiring IMPORTANT!! All cables should be securely fastened within 6” of the termination device.
Figure 21 – Wiring the Voice Unit Diagram
Page 23 of 29
Qmatic Wiring Information Guide
Figure 22 – Wiring the Voice Unit Picture
Page 24 of 29
Qmatic Wiring Information Guide
Old Voice Unit Wiring IMPORTANT!! All cables should be securely fastened within 6” of the termination device.
Figure 24 – Wiring Old Voice Units Diagram
Page 25 of 29
Qmatic Wiring Information Guide
Figure 25 – Wiring Old Voice Units Picture
Page 26 of 29
Qmatic Wiring Information Guide
Video Unit Wiring IMPORTANT!! All cables should be securely fastened within 6” of the termination device.
Figure 27 – Wiring the Video Unit Diagram
Page 27 of 29
Qmatic Wiring Information Guide
Figure 28 – Wiring the Video Unit Picture
Page 28 of 29
Qmatic Wiring Information Guide
Qmatic Monitor Wiring
Figure 30 – Wiring Qmatic Monitor Diagram
Page 29 of 29
View more...
Comments
