PROJECT SPECIFICATION FOR INSTRUMENT DATABASE
May 10, 2017 | Author: Spirit | Category: N/A
Short Description
Descripción: PROJECT SPECIFICATION FOR INSTRUMENT DATABASE...
Description
ADMA OPCO Contract No. 155436 Abu Dhabi Marine Operating COMPANY ASBUILT PROJECT FOR USSC AND DAS ISLAND
PROJECT SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
A
26 FEB 13
SDC
Issued for SDC
Rev.
Date
Status
Revision for Issue
DEVP
KRIS
Prepared Checked Approved ADMA OPCO
Total or partial reproduction and/or utilization of this document are forbidden without prior written authorization of the Owner
Category
Code
Description
Document Type
SP
Specification
Area Code
USSC and DAS
WP Project No. 021/50430 Project Code
Area Code
Discipline Code
Sequence Number
ADXXX
XX
I
05000
Revision No. Approval Class
A
3
Sheet Number
1 of
53
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
Page
: 2
of
53
Rev.
: A
Date
: 26-Feb-2013
Revision History Revision
Date
Description
A
26 Feb 13
Issued for SDC
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
Remarks
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
Page
: 3
of
53
Rev.
: A
Date
: 26-Feb-2013
Disclaimer This document has been prepared by WorleyParsons on behalf of and for the exclusive use of Abu Dhabi Marine Operating Company (ADMA OPCO) and is subject to and issued in accordance with the agreement between Abu Dhabi Marine Operating Company (ADMA OPCO) and WorleyParsons. WorleyParsons accept no liability or responsibility whatsoever for it in respect of any use of or reliance upon this document by any party other than those named above. Copying this document without the permission of Abu Dhabi Marine Operating Company (ADMA OPCO) or WorleyParsons is not permitted.
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
Page
: 4
of
53
Rev.
: A
Date
: 26-Feb-2013
CONTENTS 1.
PROJECT DESCRIPTION.....................................................................................................................7 1.1
Scope of Specification ...........................................................................................................................8
1.2
Definitions and Abbreviations ................................................................................................................8
2.
PROJECT DOCUMENTS ......................................................................................................................9 2.1
3.
ADMA OPCO specifications ..................................................................................................................9 AVEVA INSTRUMENTATION SOFTWARE ........................................................................................ 10
3.1
Overview.............................................................................................................................................. 10
3.2
AVEVA Instrumentation modules: ........................................................................................................ 10
3.3 4.
3.2.1
Instrument Engineer ................................................................................................................ 10
3.2.2
Instrument Designer ................................................................................................................ 11
3.2.3
Instrument Wiring Manager .....................................................................................................11
Security Manager................................................................................................................................. 12 AVEVA INSTRUMENTATION DATABASE AND SOFTWARE REQUIREMENTS .............................. 13
4.1
Database Server location..................................................................................................................... 13
4.2
Database Administration ...................................................................................................................... 13
4.3
Database Back-up ............................................................................................................................... 13
4.4
Software requirements and Database Version Information .................................................................. 13
4.5
AVEVA Instrumentation Language ...................................................................................................... 14
5.
DATABASE SET-UP ........................................................................................................................... 15 5.1
Domain Definition ................................................................................................................................ 15
5.2
Plant/Area Hierarchy............................................................................................................................ 15
5.3
Tag Numbering .................................................................................................................................... 18 5.3.1
Instruments ............................................................................................................................. 18
5.3.2
Loops ...................................................................................................................................... 18
5.3.3
Junction Boxes ........................................................................................................................ 19
5.3.4
Cables ..................................................................................................................................... 19
5.3.5
Control Equipment’s/Cabinets/Panels ..................................................................................... 20
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
Page
: 5
of
53
Rev.
: A
Date
: 26-Feb-2013
5.4
User Group .......................................................................................................................................... 21
5.5
Access Rights ...................................................................................................................................... 21
5.6
Process Units of Measure .................................................................................................................... 21
6.
DATABASE STRUCTURE................................................................................................................... 23 6.1
Instrument Index Data ......................................................................................................................... 23
6.2
Tag Function Catalogue ...................................................................................................................... 23
6.3
Loop Catalogue ................................................................................................................................... 24
6.4
Instrument Datasheets ......................................................................................................................... 25
6.5
Property Definitions fields .................................................................................................................... 25
7.
INSTRUMENT ENGINEER MODULE ................................................................................................. 26 7.1
8.
PICK LISTS ......................................................................................................................................... 26 7.1.1
I/O Type .................................................................................................................................. 26
7.1.2
Signal type .............................................................................................................................. 27
7.1.3
System .................................................................................................................................... 27
7.1.4
Location .................................................................................................................................. 27
7.1.5
Ex Rating ................................................................................................................................ 28
7.1.6
Status ...................................................................................................................................... 28
7.1.7
Ingress Protection ................................................................................................................... 29
INSTRUMENT DESIGNER MODULE ................................................................................................. 30 8.1
Loop Drawings ..................................................................................................................................... 30
8.2
Termination Drawings .......................................................................................................................... 30
8.3
Hook-up Drawings ............................................................................................................................... 30
9.
INSTRUMENT WIRING MANAGER ....................................................................................................32 9.1
Equipment’s ......................................................................................................................................... 32
9.2
Cables ................................................................................................................................................. 32
9.3
Cable Block Diagram ........................................................................................................................... 32
9.4
Wiring Rules ........................................................................................................................................ 32
10.
REPORTS AND DESIGN DELIVERABLES......................................................................................... 34
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
11.
Page
: 6
of
53
Rev.
: A
Date
: 26-Feb-2013
DATABASE HAND OVER ................................................................................................................... 35
APPENDIX A -
INSTRUMENT DATA FIELD LIST
APPENDIX B -
TAG FUNCTION CATALOGUE
APPENDIX C -
LIST OF INSTRUMENT DATASHEET FORMS
ATTACHMENT 1 – INSTRUMENT DATASHEETS (TOTAL 16 SHEETS)
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
1.
Page
: 7
of
53
Rev.
: A
Date
: 26-Feb-2013
PROJECT DESCRIPTION
Abu Dhabi Marine Operating Company (ADMA-OPCO) has initiated a major campaign to As-Built all engineering drawings for process and utilities plants on Das Island and Umm Shaif Super Complex (USSC) and Zakum West Super Complex (ZWSC) by developing Master As-Built intelligent 3D models and diagrams for each plant/ facility using Aveva suite software. The Package 1 of As-Built project awarded to Worley Parsons covers complete As-Built of Das Island and USSC facilities using 3D scanning technology as well the P&ID/PFD of US Wellhead- Towers (WHT), as defined in the Scope of Work. The input data consist in legacy As-Built owned by ADMA, site survey and 3D-scanning carried at site, as well the conventional site verification. The SOW also includes development and implementation of a custom Engineering and Information Management System (EIMS) based on Aveva Net software platform. The site survey, 3D scanning and 3D primitive modelling activities are subcontracted to Surtech Int’l Ltd. The intelligent 3D modelling and diagrams, 2D drawings & reports generation and site verification is going to be executed by WorleyParsons India, Hyderabad office subsidiary. The project management and coordination will be carried from the home office in Abu Dhabi. The Aveva Net software procurement, EIMS development and implementation activities are subcontracted to Aveva Solutions Ltd. The deliverables package includes 3D point clouds and primitive models, 3D intelligent models and associated 2D layouts generated from PDMS models, intelligent diagrams and associated drawings/ reports generated from Aveva suite, as well various AutoCAD drawings. As per the SOW, the Das Island and USSC facilities are breakdown in 39 units and of 96 WHT located on US Field for P&ID’s development only. The total amount of drawings/ reports to be produced is estimated to approximately 5800 documents. EIMS package includes as deliverables the Aveva Net software and associated licensing, the annual maintenance, as well delivery of scope study followed by custom implemented Aveva Net solution. The Package 2 covering complete As-Built for Zakum West Super Complex (ZWSC) and the P&ID/PFD of ZW WHT have been awarded to Litwin.
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
1.1
Page
: 8
of
53
Rev.
: A
Date
: 26-Feb-2013
Scope of Specification
The intent of this specification is to capture all the basic setup information, various modules within AVEVA Instrumentation used for this project, custom made formats, fields, tables which are created to generate Instrumentation control system project deliverables required for As-Built project .for USSC and DAS ISLAND AVEVA Instrumentation will cover Instrumentation related information and data in order to complete necessary deliverables within AVEVA Instrumentation modules. The content of formats, field’s tables and degree of customisation may vary depending on project requirement. AVEVA Instrumentation database is live continuously updated throughout the whole cycle of the project.
1.2
Definitions and Abbreviations
Definitions COMPANY
Abu Dhabi Marine Operating Company (ADMA-OPCO)
Detail Engineering Contractor
Worley Parsons Pty Ltd
Project drawings/ documents Project Administrator
Reference drawings/ documents for the specific item(s) for purchase AVEVA Instrumentation Database administrator
USER
AVEVA Instrumentation database user
Abbreviations EPC
Engineering Procurement and Construction
AI
AVEVA Instrumentation
IP
Ingress Protection
SQL
Structured Query Language
USSC
Umm shaif Super Complex
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
2.
PROJECT DOCUMENTS
2.1
ADMA OPCO specifications
Page
: 9
Rev.
: A
Date
: 26-Feb-2013
CP-00
Code of practices
CP-00(Part-4)
Code of practices for plant design (Instrumentation)
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
of
53
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
3.
AVEVA INSTRUMENTATION SOFTWARE
3.1
Overview
Page
: 10
of
53
Rev.
: A
Date
: 26-Feb-2013
AVEVA Instrumentation (AI) is software for managing Instrumentation design data and documentation. This is a Windows based integrated relational database system supported with a Microsoft Access or SQL server. AVEVA Instrumentation comprises of three integrated modules, is divided into various front end modules which shares a common multi user database that captures various data relating to deliverables and reports generated from AI. The three modules of AVEVA Instrumentation are: -
Instrument Engineer
-
Instrument Designer
-
Instrument Wiring Manager
3.2
AVEVA Instrumentation modules:
3.2.1
Instrument Engineer This module enables instrument index data entry, change tracking, instrument index, I/O list reports, definition of instrument data sheet (specification sheet) layouts and generation of data sheets, management of reports and documentation. The features include: -
Instrument List (Index)
-
Loop list
-
Datasheets (Specifications)
-
Reports
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
3.2.2
Page
: 11
of
53
Rev.
: A
Date
: 26-Feb-2013
Instrument Designer This module enables automatic generation and revision of CAD drawings from the multi user project/plant database with or without use of templates. It manages the process of CAD drawing creation, drawing revision update, transferring of data to drawings, parametric creation of termination (wiring) drawings and printing CAD files. The features include:
3.2.3
-
Drawing List Management
-
Loop Diagram generation
-
Termination Diagram generation
-
Hook-up/Installation Drawing generation
Instrument Wiring Manager Instrument wiring manager handles all tasks related to detail cable, wiring and termination design creating data which is used by Instrument designer module for drawing generation. Instrument Wiring Manager has three integrated modules: -
Wiring Manager - Equipment Enables graphical definition and editing of equipment terminal arrangements including terminal strips, devices and I/O modules (including fieldbus devices), design of 'internal' wiring and rule based creation of cable terminations, assign tags to junction boxes.
-
Wiring Manager - Cables Enables definition of project cables from a user definable cable catalogue and assignment of cable ends to equipment including fieldbus devices. Also assignment of catalogue driven cable glands, gland adapter assignment and Bill of Materials reporting, cable schedules, and cable drumming reports.
-
Wiring Manager - Cable Block Diagrams Provides a graphical representation of cable interconnections. Users can create equipment and cables within each diagram or drag & drop of equipment into a diagram and wire terminations. All interconnected equipment is automatically added and the cables shown.
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
3.3
Page
: 12
of
53
Rev.
: A
Date
: 26-Feb-2013
Security Manager The Security Manager application enables an Administrator or Super User to setup access and security rights on 'Objects' in an SQL Server database. Security Manager includes the following features: -
Creating New Project/Edit project
-
Create Groups for example Instrument Engineers, Instrument Designers, Process Engineers
-
Creating New Users and assigning to a Group depending upon their role in the project
-
Access rights management (read-write, read only or no access)
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
Page
: 13
Rev.
: A
Date
: 26-Feb-2013
4.
AVEVA INSTRUMENTATION DATABASE AND SOFTWARE REQUIREMENTS
4.1
Database Server location
of
53
The AI database SQL server for ADMA As-Built Project for USSC & Das Island shall be physically located in the WorleyParsons Hyderabad Office.
4.2
Database Administration The SQL server set-up and installation of the software on USER pc is the responsibility of the SQL server administration from IT group. The SQL server administrator shall add each user log in to the database and add them to a USERS list which gives them permission to access AVEVA Instrumentation database objects. The Project Administrator is the person from the project team or Lead Engineer is responsible for creating new project, implementing USER access rights to AVEVA Instrumentation database Objects, selecting desire Instrument Tag format for the project, creating and maintaining pick lists and creation of catalogues in the all AI modules.
4.3
Database Back-up SQL server administrator is the responsible person to take periodic backups of the SQL server database – every day after office hours. The email notification of this backup log will be transmitted by the WorleyParsons IT group to the Lead Engineer, delegate Project Administrator as well as the WorleyParsons IT group personnel.
4.4
Software requirements and Database Version Information
SQL Server Version - 2008
AVEVA Instrumentation software version - 12.1 Fix 3
Operating System – Microsoft Windows XP professional or Microsoft Windows 7 professional
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
4.5
Page
: 14
Rev.
: A
Date
: 26-Feb-2013
AVEVA Instrumentation Language All fields are filled in English language and shall generally be in capital letters.
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
of
53
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
5.
Page
: 15
of
53
Rev.
: A
Date
: 26-Feb-2013
DATABASE SET-UP
The AVEVA Instrumentation standard build, complete with all common configuration data, shall be available for use for the ADMA As-Built Project for USSC & Das Island Users.
5.1
Domain Definition
Description
Required
Entered Data
Database Name:
Yes
AI_ADXXX
Project Number:
Yes
ADXXX
Description:
Yes
As-Built Project for USSC & Das Island
Instrument Tag Format
Yes
ISA with Area (delimiters)
Project Administrator:
Yes
Administrator
Administrator Password
Yes
xxxxxxxx
Database type
Yes
SQL Server
SQL Server name
Yes
Inhydwpsql01v
Project Folder
Yes
AI_ADXXX
Where XXX Denote USSC (300) and DAS Island (200)
5.2
Plant/Area Hierarchy
Plant Area Type DAS Island
Area Number
08.0
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
Area Description
ZK SEPARATORS
Short Descripti on
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
Page
: 16
Rev.
: A
Date
: 26-Feb-2013
DAS Island
31-0
API SEPARATOR
DAS Island
4-6
LNG MANIFOLD
DAS Island
10-1
MOL, MGL, CONDENSATE
DAS Island
16
METERING BAY
DAS Island
9-6
CMP
DAS Island
33&1&04.5
ONSHORE FLARES, FINGER FLARES & ATMOSPHERIC MANIFOLD
DAS Island
03-0
BUNDUQ PLANT
DAS Island
04.0
US SEPARATORS
DAS Island
4-3,8-7
US & ZK STRIPPERS
DAS Island
08.1,8.6
GSU 4
DAS Island
28
10" ABK LINE
DAS Island
35
MONOPOD TOWER
DAS Island
36-1
SWDP
DAS Island
40
SPHEROIDS
DAS Island
8-5
COCIF
DAS Island
90
INSTRUMENT AIR & NITROGEN PLANTS
DAS Island
90
OFFSITE & PIPERACKS
DAS Island
6.0,6.2,06.3 & 6.4
BOILERS
DAS Island
6-4
BOILERS 6& 7
DAS Island
12.2,60.0 TO 60.8
POTABLE WATER PRODUCTION & STORAGE
DAS Island
12
COS TANKS
DAS Island
15
OLD CO PUMPS
DAS Island
10
CTU
USSC
181
NRP
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
of
53
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
USSC
180
OCCP
USSC
182
ERP
USSC
176
CAP GAS WELL
USSC
178
ABK TIP
USSC
193
BRIDGE B7
USSC
194
BRIDGE B8
USSC
196
BRIDGE B10
USSC
197
BRIDGE B11
USSC
423
BRIDGE B13
USSC
427
NGTP
USSC
422
TA
USSC
415
36" MOL
USSC
184
PGB
USSC
179
CSP
USSC
177
GTP
USSC
350
GTP EXTN
USSC
187
B1
USSC
188
B2
USSC
189
B3
USSC
190
B4
USSC
191
B5
USSC
192
B6
USSC
359
S1
USSC
360
S2
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
Page
: 17
of
53
Rev.
: A
Date
: 26-Feb-2013
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
USSC
361
S3
USSC
185
MODULE 5
USSC
186
MODULE 2
5.3
Tag Numbering
5.3.1
Instruments
Page
: 18
of
53
Rev.
: A
Date
: 26-Feb-2013
Instrument Tag numbering format shall be identified ISA with Area (delimiters) in AVEVA Instrumentation as per ADMA STD CP-00 as follows:
Instrument Tag format: AAA-BBBB-CCCC/X Sequence
Seperator
1
Area Number (AAA)
2
-
Functional Identification (BBBB)
3
-
Loop Identification Number (CCCC)
4
5.3.2
Description
Tag suffix (X) - Option
Loops Loop numbering format shall be identified in AVEVA Instrumentation as follows:
Loop Number: AAA-BB-CCCC/X Sequence
Seperator
1
Description Area Number (AAA)
2
-
Loop Code (BB)
3
-
Loop Identification Number (CCCC)
4
Loop suffix (X) - Option
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
5.3.3
Page
: 19
of
Rev.
: A
Date
: 26-Feb-2013
Junction Boxes
Junction box numbering shall be identified in AVEVA Instrumentation as follows:
Junction box Number: AAA-BBB-CCCC Sequence
Seperator
Description Area Number (AAA)
1
Junction box type (BBB) IJB – Intrinsically safe 2
3
5.3.4
-
-
AJB – Non Intrinsically safe
AMB – Marshalling boxes
Junction box Identification Number (CCCC)
Cables
Instrument cables, F&G cables, communication cables and 24 V Dc power supply cables shall be identified in AVEVA Instrumentation as follows:
Cable Number: AX BBBBB C Sequence 1
Seperator
Description A – ADMA X – Circuit Function
2
L – Instrumentation E – Electrical X – Pneumatic T – Telecommunications PI – Public Address
3
Cable Identification Number (BBBBB)
4
Suffix (C)
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
53
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
5.3.5
Page
: 20
of
53
Rev.
: A
Date
: 26-Feb-2013
Control Equipment’s/Cabinets/Panels Control equipment’s such as marshalling cabinet, system cabinets and control panels shall be identified in AVEVA Instrumentation as follows:
Equipment/Cabinet number: AAA-BBB-CCCC X Sequence
Seperator
1
Description Area Number (AAA) Functional Description (BBB)
2
-
3
-
Identification Number (CCCC)
4
Suffix (X) - Option
Function Description:
Description
Code DAU
Data Acquisition unit
ESD
Emergency Shutdown
F&G
Fire & Gas
FGCP
Fire & Gas Control Panel
IRC
Interposing Relay cabinet
LCP
Local Control Panel
MC
Marshalling cabinet
PCS
Process Control System
UCP
Unit Control Panel
MMS
Machine Monitoring System
IOS
Input Output Station
HIPPS
High Integrity Pressure Protection System
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
5.4
Page
: 21
of
53
Rev.
: A
Date
: 26-Feb-2013
User Group User Groups within AVEVA Instrumentation are defined by the Project Administrator during project setup or whenever required during project life cycle. The following User Groups are created in AI_50430DAS and AI_50430USSC Domain: o o o
5.5
Instrument Engineers Instrument Designers Process Engineers
Access Rights The access rights for each user group are defined by the Project Administrator during project set up or whenever required during project cycle. AI security/access is controlled through Objects per user groups for each module in Security manager. A user group is a means of grouping individual users together that require the same level of access (readwrite or read only) of specific types of activities. For each of these user groups access to specific activities are assigned through Objects e.g. In Engineer module Instruments & Loops, Instrument Datasheets etc.., In Designer module Catalogues, Drawings etc…, In Wiring manager Cables, Equipment’s, Terminations etc….. Project Administrator will have a default setting of full access for all AI modules for all Objects and Set-up activities.
5.6
Process Units of Measure The default process units are available in AVEVA Instrumentation for the use. The process units shall be added in the AI as listed in table below for the project requirements.
Units
Parameter
Abbreviation 3
3
Cubic foot, barrel, Cubic meter
ft , bbl, m
- Hydrocarbon liquid & water
Barrels / day, Cubic meter / hour
BPD, m / h
- Other
US gallons / min.
gpm
Volume Flow (volume) :
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
3
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
Page
: 22
of
Rev.
: A
Date
: 26-Feb-2013
- Flow (volume) – Crude Sale
Stock tank barrels / day
STBPD
- Flow (volume) gas
Millions Standard Cubic feet / day
MMSCFD
Flow (mass)
Pounds per hour,
lb/h,
Kilogram per hour
kg/h
Pounds per square inch, Bar
psia, psig , bara /
Pressure
(1)
barg, Pressure (close to atmosphere)
Millibar, Millimetre water column
Vacuum
Inches
of
water,
Millimetre
Mbar, mm WC water in. WG, mm WC
column Temperature (Process)
Degrees Fahrenheit, Degree Celsius
°F, °C
Temperature (Other)
Degrees Celsius
°C
Level
Metres
m
Level (field instrumentation)
Percentage
%
Length
Metres or millimetres
m or mm
Liquid Specific Gravity
Degrees API, Specific gravity
°API, sp. gr.
Liquid Density
Pounds per cubic foot,
lb/ft
Kilogram per cubic metre
kg/m
Absolute Viscosity
Centipoise
cP
Kinematic Viscosity
Centistokes
cSt
Heat
British Thermal unit, Kilo-calorie
Btu, Kcal
Power
Kilowatt or watt
kW or W
Mass (for mech. Design)
Kilograms or metric tons
kg or t
Pipe diameter
Inches
in.
Time
Second / minute / hour / day
s/min./h/d
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
3
, 3
53
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
6.
DATABASE STRUCTURE
6.1
Instrument Index Data
Page
: 23
of
53
Rev.
: A
Date
: 26-Feb-2013
The instrument index is developed and issued in conjunction with the P&ID’s, F&G detector layouts for F&G instruments and Cause & Effect chart. The index serves as the indices to each individual instrument (hard or soft tag) and supporting documents and drawings As a general rule, all instrument tags shall be entered into AVEVA Instrumentation through Instrument Engineer module. Care should be taken to ensure all tags and associated data is entered consistently. The workflow for creating a tag shall be to create the loop first and add the tag to the Loop. Adding the tags by the typical loop method is the preferred way. Refer Appendix-A for the list of the fields available / created for use as part of AVEVA Instrumentation database. These fields are available in Instrument Engineer module under Grid manager in the different tables Instrument List, Loop List. From Instrument List data grid USER can select database fields to customise and define the view according to project requirements.
6.2
Tag Function Catalogue The function components of the instrument tags are embedded within Tag Function catalogue table; these values are used to generate default data for tags as they are entered into the database. This will be updated on an ongoing basis as required, for the project requirements. An Instrument function is required for all tagged items. The number of Instrument tag functions required will depend on P&ID diagrams, Fire and Gas Location layouts, and Cause & Effect chart documents as per project requirements. Instrument tag functions and its values are defined by the Project Administrator or USER as per project requirements. Any addition or modifications to Instrument tag function shall be directed to Project administrator or Lead Engineer of this project. Refer Appendix-B tag functions listed in the table shows the AI Instrument Types and a summary of their value. This table is considered as a guide only and is to be considered carefully before applying. Only those Instrument tag functions required for this project need to be switched on. The Instrument tag functions are used for the automatic generation of data either at the inputting of tags or for ensuring standardization of data at the later stages. Control system profile is used where the tag is used as a control system or has an associated control system tag. The tag will have an I/O type. The wiring rule allows to auto generate field Instrument wiring/cabling.
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
6.3
Page
: 24
of
53
Rev.
: A
Date
: 26-Feb-2013
Loop Catalogue The listed loop codes are available in the AVEVA Instrumentation under Loop Catalogue list. The type of loop code can be selected and assigned from the list below to new loop numbers.
Loop Code
Description
A
Analysis
B
Burner
C
Conductivity
D
Density
E
Voltage
F
Flow
G
Gauging (Dimension)
H
Hand
I
Current
J
Power
K
Time
L
Level
M
Moisture (Humidity)
N
MCC
O
User defined
P
Pressure
PD
Pressure Differential
Q
Quantity
R
Radioactivity
S
Speed (Frequency)
T
Temperature
U
Photocell
V
Vibration
W
Mass or Force
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
6.4
X
Miscellaneous
Y
User Defined
Z
Position
Page
: 25
of
53
Rev.
: A
Date
: 26-Feb-2013
Instrument Datasheets Refer attached Appendix-C for the customised Instrument Datasheets Forms List as per project requirements for the use in As-Built Project for USSC & Das Island. Revision control is being implemented using AVEVA revision managed capabilities.
6.5
Property Definitions fields AVEVA Instrumentation supports user defined Properties for Instrument Datasheets. These properties enable users to create meaningful attribute names for data that has no other logical property or field within the project database. Properties can belong to one of two Property Type groups:
Instrument Properties
Process Properties.
The property definitions fields are available in AVEVA Instrumentation. These property definition fields will be customised for the Instrument Data and Process data as per project requirements in the Individual Datasheet forms.
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
7.
INSTRUMENT ENGINEER MODULE
7.1
PICK LISTS
Page
: 26
of
53
Rev.
: A
Date
: 26-Feb-2013
The following is the list of default Pick Lists, which are already available / created for use as part of AVEVA Instrumentation Database. Project Administrator shall control all the pick lists for addition/deletion of items and shall add new pick list whenever required during project life cycle.
7.1.1
I/O Type This field represents the I/O type of the Instrument. The I/O is associated to the system within the ‘System’ field. I/O type
Description
-
No I/O
AI
Analogue Input
AI-R
Analogue Input Redundant
AO
Analogue Output
AO-R
Analogue Output Redundant
DI
Digital Input
DO
Digital Output – Potential free contact
PI
Pulse Input
PO
Pulse Output
SAI
Serial Interface Analogue Input
SAO
Serial Interface Analogue Output
SDI
Serial Interface Digital Input
SDO
Serial Interface Digital Output
SW
Software
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
7.1.2
Page
: 27
of
Rev.
: A
Date
: 26-Feb-2013
Signal type This field represents the Signal type of the Instrument. The signal type is associated to the I/O type.
7.1.3
Signal type
Description
IS
Intrinsically Safe
NIS
Non Intrinsically safe
Serial
Serial Communication
System This field represents the system type associated to Instrument tag.
7.1.4
System type
Description
DAU
Data Acquisition Unit
PCS
Process Control System
ESD
Emergency Shutdown System
HIPPS
High Integrity Pressure Protection System
MMS
Machine Monitoring System
FGS
Fire & Gas System
Location This field represents field device physical location.
Location
Description
FLD
Field
LCR
Local Control Room
CCR
Central Control Room
MCC
Motor Control Centre
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
53
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
7.1.5
LCP
Local Control Panel
SS
Substation
Page
: 28
of
53
Rev.
: A
Date
: 26-Feb-2013
Ex Rating This field “EX Rating” identifies the classification of the signal, which is defined as follows:
7.1.6
Signal Class
Description
EEx’i’
Intrinsically Safe
EEx’d’
Explosion proof
EEx’e’
Increased Safety
EEx’m’
Encapsulated
STD
Standard Signal (i.e. No classification)
Status This field is used to determine whether an instrument is new, old, to be relocated, existing, deleted etc. This data is used to identify the status of the instrument and to help filter the data.
Status
Description
NEW
New Instrument
DEL
Existing Instrument to be Demolished
EXIST
Existing Instrument (No modification)
REL
Existing Instrument Relocated
REP
Existing Instrument to be replaced with New Instrument
MOD
Existing Instrument to be modified
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
7.1.7
Page
: 29
Rev.
: A
Date
: 26-Feb-2013
Ingress Protection
From the following, Ingress protection class shall be defined for Instruments in database
IP55 IP56 IP63 IP64 IP65 IP66
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
of
53
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
8.
Page
: 30
of
53
Rev.
: A
Date
: 26-Feb-2013
INSTRUMENT DESIGNER MODULE Instrument Designer module manages all tasks typically handled by an Instrument Designer during a project life cycle including CAD drawing generation, drawing list management, updating of revisions and printing of CAD files for loop diagrams, termination diagrams, Hook-up drawings etc.
8.1
Loop Drawings The loop drawing can be generated using ACAD typical loop templates with updated attributes from the AVEVA Instrumentation database for the data from Instrument Engineer module (Manufacturer, model number, P&ID etc..) and Instrument Wiring manager (Cable, termination details, wire numbers etc..). In order to complete loop drawings from AVEVA Instrumentation, the minimum following information shall be available from Control System vendor.
8.2
Marshalling cabinet layouts
Marshalling cabinet Field cable assignments
Cross wiring
I/O Assignment (System cabinet)
Termination Drawings The termination drawing can be generated in standard available report formats from AVEVA Instrumentation database including data from and Instrument Wiring manager terminal strip details, cables, wire markers etc..
8.3
Hook-up Drawings In order to generate Hook-up drawings from the AVEVA Instrumentation database, following activities needs to be carried out:
ACAD Hook-up template drawing with updated attributes from AVEVA Instrumentation database as per project requirements
Hook-up items list in accordance to project requirements
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
Page
: 31
of
53
Rev.
: A
Date
: 26-Feb-2013
Assign Hook-up type (Hook-up drawing template) to each instrument to generate Hook-up drawing
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
9.
Page
: 32
of
53
Rev.
: A
Date
: 26-Feb-2013
INSTRUMENT WIRING MANAGER Instrument Wiring Manager manages all tasks typically carried out by an Instrument Designer relating to detail cable, wiring and termination design. This includes definition of equipment terminal arrangements (field devices, junction boxes and cabinet devices such as relays, IS barriers and I/O modules), cable creation and termination, cross-patch wiring etc., generation of Cable Schedules and cable, cable gland and cable gland adapter Bill of Materials etc.
9.1
Equipment’s All standard equipment’s such as Instrument field devices, Junction boxes, Local Panels, Marshalling Cabinets and System cabinets including their strips, terminals, and I/O cards shall be created in the AVEVA Instrumentation database as per project requirements.
9.2
Cables In wiring manager, default cables are available in cable catalogue. New cables shall be created in the cable catalogue based on Project Instrument cable specifications which will serve as Project default cables. All project cables must be based on a catalogue cable to ensure project cable properties (size, Number of cores, type etc.) Meeting project requirements.
9.3
Cable Block Diagram The Cable block diagram is a graphical view of cabling and interconnection between different Equipment’s which allows interactive access for editing purpose of wiring manager objects (Equipment’s, cables, editing termination details).
9.4
Wiring Rules AVEVA Instrumentation uses 'Wiring Rules' to auto generate typical field instrument wiring/ cabling. Wiring Rules enables to build devices and their associated terminal arrangements, cables, Terminations etc. in Wiring Manager.
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
Page
: 33
of
53
Rev.
: A
Date
: 26-Feb-2013
To apply wiring rule to field Instrument, following information needs to be defined:
Terminal Arrangement - number of terminals, their markings and sequence.
Default Signal Numbers (wire numbers) to be used on wire terminations.
Default Project Cable Type - type of catalogue cable (individual cores, pairs or triad, shielded/screened, armoured etc.)
Default Cable Number, based on project cable numbering philosophy
Default Wire terminations at field device terminals (e.g. core 1 to terminal 1, core 2 to terminal 2 etc.).
Default wire terminations at non-field device - at the other end (typically a Junction Box).
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
10.
Page
: 34
of
53
Rev.
: A
Date
: 26-Feb-2013
REPORTS AND DESIGN DELIVERABLES AVEVA Instrumentation has an in-built Report Manager that enables users to create and customise reports as per project requirements. The Report Manager is available from most Grid Views within each AVEVA Instrumentation module.
All modules of AVEVA Instrumentation are used to generate following project deliverables for the AsBuilt Project for USSC & Das Island
Instrument Index
Instrument I/O list
Instrument Datasheets
Instrument cable schedule
Instrument JB wiring diagrams
Interconnection wiring diagrams
Instrument Loop diagrams
Instrument Hook-up drawings
Refer ATTACHMENT-1 for attached customised project datasheet templates for reference only.
Note: Other deliverables report formats will be attached in the subsequent revision.
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
11.
Page
: 35
of
53
Rev.
: A
Date
: 26-Feb-2013
DATABASE HAND OVER Project administrator will be in charge of all system administration activities and ownership of project database till the end of phase for this project.
Ensure all data is free of any database exceptions and orphan entries.
The following data will be handed over to ADMA OPCO at the end of this project:
SQL server AVEVA Instrument Database
All CAD templates for loop drawings, hook-up drawings, Customised Instrument datasheet forms and customised reports used to generate the required documents.
AVEVA Instrumentation project administration and ownership of database shall be transferred to ADMA OPCO who will further handover to Client.
Note: All temporary and test data, test CAD blocks, temporary browser views, reports unused panels and cables etc. shall be removed from the database before custody transfer.
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
Appendix A Table Name
Page
: 36
of
Rev.
: A
Date
: 26-Feb-2013
Instrument Data Field List
Field Name
Caption
Field Description
Use
Action
CTRL ACT
Y
Instrument List
AlarmHi
ALARM_H
Controller Action D: Di t R R High Alarm point
Instrument List
AlarmHiHi
ALARM_HH
High High Alarm point
Y
Instrument List
AlarmLow
ALARM_L
Low Alarm point
Y
Instrument List
AlarmLowLow
ALARM_LL
Low Low Alarm point
Y
Instrument List
AreaClassification
AREA_CLASS
Y
Instrument List
AreaNo
AREA_No
Hazardous Area Cl ifi ti Area Description
Instrument List
CalcTypeID
Calc. Type
Instrument List
CalibratedRangeHigh
CALIB_RANGE_HI
Instrument List
CalibratedRangeLow
CALIB_RANGE_LO
CalibratedRangeUnits
CALIB RANGE UNIT
Instrument List
Contract No
Budget_Ref
Instrument List
Cost
Cost
Datasheet No
DATASHEET NO
Instrument List
DCS1
SYSTEM
Instrument List
DCS10
DCS10
N
Instrument List
DCS11
DCS11
N
Instrument List
DCS12
DCS12
N
Instrument List
DCS13
DCS13
N
Instrument List
DCS14
DCS14
N
Instrument List
DCS15
DCS15
N
Instrument List
DCS16
DCS16
N
Instrument List
DCS17
DCS17
N
Instrument List
DCS18
DCS18
N
Instrument List
DCS19
DCS19
N
Instrument List
Instrument List
Instrument List
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
Y
Y N
Maximum Calibration Range Minimum C lib ti R Engineering Units for Calibration range Client Contract Number
Y Y Y Y N
Instrument D t h tN b Control System
Y Y
53
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
Page
: 37
of
Rev.
: A
Date
: 26-Feb-2013
Table Name
Field Name
Caption
Field Description
Instrument List
DCS2
SYSTEM_2
Control System
Instrument List
DCS20
DCS20
N
Instrument List
DCS21
DCS21
N
Instrument List
DCS22
DCS22
N
Instrument List
DCS3
SIGNAL_2
Instrument List
DCS4
DCS04
N
Instrument List
DCS5
DCS05
N
Instrument List
DCS6
DCS06
N
Instrument List
DCS7
DCS07
N
Instrument List
DCS8
DCS08
N
Instrument List
DCS9
DCS09
N
Instrument List
DCSIO
I/O_TYPE
Instrument I/O type
Y
Instrument List
DCSIOLocation
I/O_LOC
Instrument I/O Location
Y
Instrument List
DCSIOStatus
DCS Status
Instrument List
DCSRev
REV_IO LIST
Instrument List
DCSRevDesc
DCSRevDesc
N
Instrument List
DerivativeTime
DerivativeTime
N
Instrument List
Description
INSTRUMENT TYPE
Instrument List
DevHi
DevHi
N
Instrument List
DevHiHi
DevHiHi
N
Instrument List
DevLow
DevLow
N
Instrument List
DevLowLow
DevLowLow
N
Instrument List
DisplayRangeHigh
DCS_RANGE_HI
Maximum DCS Range
Y
Instrument List
DisplayRangeLow
DCS_RANGE_LO
Minimum DCS Range
Y
Instrument List
DisplayRangeUnits
DCS_RANGE_UNITS
Engineering Units for DCS R
Y
Instrument List
ExCertAuthority
ExCertAuthority
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
System_2 Signal type
Use Y
Y
N I/O List Revision
Instrument Type D i ti
Y
Y
N
53
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
Page
: 38
Rev.
: A
Date
: 26-Feb-2013
Table Name
Field Name
Caption
Instrument List
ExCertCertification
CERTIFICATION
Y
Instrument List
ExCertExpiryDate
ExCertExpiryDate
N
Instrument List
ExCertificateNo
ExCertificateNo
N
Instrument List
ExOtherApproval
ExOtherApproval
N
Instrument List
ExRating
EEX_PORT
Instrument List
ExStatus
ExStatus
Instrument List
FailPosition
VALVE_FAIL_POS
Instrument List
ForeignKEY
ForeignKEY
N
Instrument List
Gain
Gain
N
Instrument List
HookUpReqd
HookUpReqd
N
Instrument List
HookUpType
HKUP_TYPE
Instrument List
iGeoLocation
GeoLocation
Instrument List
Ingress Protection
IP Rating
Instrument List
InstallCost
InstallCost
Instrument List
InstallDwgNo
HKUP_DWG_NO
Hook-up Drawing
Y
Instrument List
IntegralTime
IntegralTime
Number
N
Instrument List
ISAFunc
PROCESS_FUNCTION
Process Function Type
Y
Instrument List
ISALocation
LOCATION
Instrument Location
Y
Instrument List
IService1
INST_SERVICE
Instrument Service
Y
Instrument List
IService2
Instrument Service2
Instrument List
JunctionBox
JB_NUMBER
Instrument List
LEDateTime
LEDateTime
N
Instrument List
LEUser
LEUser
N
Instrument List
LinkedDocuments
Attachments
N
Instrument List
LNumber
Number
N
Instrument List
LocationDwg
LOC_DWG
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
Field Description
of
Instrument Signal Cl ifi ti
Use
Y N
Valve Failure action or Air F il
Hook-up Type
Y
Y N
Instrument IP Class
Y N
N Junction
Instrument Location D i N b
Y
Y
53
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
Page
: 39
Rev.
: A
Date
: 26-Feb-2013
Field Description
of
Table Name
Field Name
Caption
Instrument List
LoopDwgCode
LoopDwgCode
Instrument List
LoopDwgNo
LOOP_DWG
Loop Drawing Number
Y
Instrument List
Manufacturer
MANUFACTURER
Manufacturer Name
Y
Instrument List
MOCNo
MOC No
Instrument List
ModelNo
MODEL_NO
Model Number
Y
Instrument List
OldTagNo
OLD_TAG_NO
Old Tag Number
Y
Instrument List
OperatingPrinc
OperatingPrinc
Instrument List
OrderBy
LOOP_ORDER
Instrument List
OtherIO
OtherIO
N
Instrument List
OutputLimitHi
OutputLimitHi
N
Instrument List
OutputLimitLow
OutputLimitLow
N
Instrument List
PIDNo
P&ID NO
P&ID Number
Instrument List
PlantConnection
EQUIPMENT_NO
Equipment Number if I t t l
Use N
N
Y Y
Tag order in the Loop
Y Y t d
Instrument List
PLC1
SIS1
N
Instrument List
PLC10
SIS10
N
Instrument List
PLC11
SIS11
N
Instrument List
PLC12
SIS12
N
Instrument List
PLC13
SIS13
N
Instrument List
PLC14
SIS14
N
Instrument List
PLC15
SIS15
N
Instrument List
PLC16
SIS16
N
Instrument List
PLC17
SIS17
N
Instrument List
PLC18
SIS18
N
Instrument List
PLC19
SIS19
N
Instrument List
PLC2
SIS2
N
Instrument List
PLC20
SIS20
N
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
53
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
Page
: 40
Rev.
: A
Date
: 26-Feb-2013
Table Name
Field Name
Caption
Instrument List
PLC21
SIS21
N
Instrument List
PLC22
SIS22
N
Instrument List
PLC3
SIS3
N
Instrument List
PLC4
SIS4
N
Instrument List
PLC5
SIS5
N
Instrument List
PLC6
SIS6
N
Instrument List
PLC7
SIS7
N
Instrument List
PLC8
SIS8
N
Instrument List
PLC9
SIS9
N
Instrument List
PLCIO
PLC I/O
N
Instrument List
PLCIOLocation
SIS Location
N
Instrument List
PLCIOStatus
SIS Status
N
Instrument List
PLCRev
SISRev
N
Instrument List
PLCRevDesc
SISRevDesc
N
Instrument List
PowerSupply
PWR_SUPP
Instrument List
Prefix
Prefix
Instrument List
ProcessConnType
PROCESS_CONN
Process
Y
Instrument List
ProjectStatus
STATUS
Instrument Status
Y
Instrument List
RangeHigh
INST_RANGE_HI
Maximum
Y
Instrument List
RangeLow
INST_RANGE_LO
Minimum
Y
Instrument List
RangeUnits
ENGG_UNIT
Engineering Units
Y
Instrument List
Remarks
REMARKS_1
Instrument Remarks
Y
Instrument List
ReqdInModel
ReqdInModel
N
Instrument List
RequiredDate
RequiredDate
N
Instrument List
RequisitionNo
REQ_NO
Instrument List
SetPoint
SetPoint
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
Field Description
of
Power Supply voltage i df I t t
Use
Y N
Instrument Requisition N b
Y N
53
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
Page
: 41
of
Rev.
: A
Date
: 26-Feb-2013
Table Name
Field Name
Caption
Field Description
Instrument List
SignalType
SIGNAL_TYPE
Instrument Signal Type
Instrument List
SignalVoltage
SignalVoltage
N
Instrument List
Size
Size
N
Instrument List
Suffix
Suffix
N
Instrument List
Supplier
SUPPLIER
Instrument Vendor Name
Y
Instrument List
TagNo
TAG NUMBER
Instrument Tag Number
Y
Instrument List
TagPart
TagPart
N
Instrument List
TermDwgNo
TermDwgNo
N
Instrument List
UserField1
PO Number
Instrument List
UserField10
SIL Rating
Instrument List
UserField11
UserField11
N
Instrument List
UserField12
UserField12
N
Instrument List
UserField13
UserField13
N
Instrument List
UserField14
UserField14
N
Instrument List
UserField15
UserField15
N
Instrument List
UserField16
UserField16
N
Instrument List
UserField17
UserField17
N
Instrument List
UserField18
UserField18
N
Instrument List
UserField19
UserField19
N
Instrument List
UserField2
UserField2
N
Instrument List
UserField20
UserField20
N
Instrument List
UserField21
SPECIFICATION_NO
Instrument List
UserField22
UserField22
N
Instrument List
UserField23
UserField23
N
Instrument List
UserField24
UserField24
N
Instrument List
UserField25
UserField25
N
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
Instrument Purchase Od N b SIL Rating
Instrument Specification N b
Use Y
Y Y
Y
53
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
Page
: 42
Rev.
: A
Date
: 26-Feb-2013
Table Name
Field Name
Caption
Instrument List
UserField26
UserField26
N
Instrument List
UserField27
UserField27
N
Instrument List
UserField28
UserField28
N
Instrument List
UserField29
UserField29
N
Instrument List
UserField3
UserField3
N
Instrument List
UserField4
UserField4
N
Instrument List
UserField5
UserField5
N
Instrument List
UserField6
UserField6
N
Instrument List
UserField7
UserField7
N
Instrument List
UserField8
UserField8
N
Instrument List
UserField9
UserField9
N
Instrument List
VendorSupplied
VendorSupplied
N
Instrument List
WiringConfig
WiringConfig
N
Instrument List
WorkPackNo
WorkPackNo
N
Loop List
DwgRequired
Drawing
N
Loop List
LEDateTime
LEDateTime
N
Loop List
LEUser
LEUser
N
Loop List
LNo
WiringConfigInfo
N
Loop List
LoopNo
LOOP NUMBER
Loop Number
Y
Loop List
LoopPV
WIRING RULE
Instrument Field Wiring
Y
Loop List
LoopType
LoopType
Loop List
LService1
LOOP SERVICE
Loop List
LService2
Loop Service2
N
Loop List
OldLoopNo
OldLoopNo
N
Loop List
ProjectStatus
Status
N
Loop List
Remarks
REMARKS_2
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
Field Description
of
Use
N Loop Service
I/O List Remarks
Y
Y
53
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
Page
: 43
Rev.
: A
Date
: 26-Feb-2013
Table Name
Field Name
Caption
Loop List
TagPart
TagPart
N
Loop List
UserField1
UserField1
N
Loop List
UserField2
UserField2
N
Loop List
UserField3
UserField3
N
Loop List
UserField4
UserField4
N
Loop List
Wired
Wired
N
WorkPacks
WorkPackNumber
WorkPackNumber
N
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
Field Description
of
Use
53
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
Appendix B -
Functi on
Description
Page
: 44
Rev.
: A
Date
: 26-Feb-2013
53
Tag Function Catalogue
I/O Type
Locati on
Wiring Rule
AE
CO2 Analyser Element
FLD
AE
Gas Chromatograph Element
FLD
AE
H2S/Sulphur Analyser Element
FLD
AE
Hc Due Point Analyser
FLD
AE
Moisture Analyser Element
FLD
AE
Oxygen Analyser Element
FLD
AE
Sulphur Analyser
FLD
AI
Indicator
DCS
AIC
Controller
DCS
AT
Analyser Transmitter
AI
FLD
2 Wire Tx To JB
AT
CO2 Analyser
AI
FLD
2 Wire Tx To JB
AT
Gas Chromatograph Transmitter
AI
FLD
2 Wire Tx To JB
AT
H2S/Sulphur Analyser Transmitter
AI
FLD
2 Wire Tx To JB
AT
Hc Due Point Transmitter
AI
FLD
2 Wire Tx To JB
AT
Moisture Transmitter
AI
FLD
2 Wire Tx To JB
AT
Oxygen Transmitter
AI
FLD
2 Wire Tx To JB
AY
Selector
BE
Flame Detector
BE
Fusible Plug
FLD
BI
Indicator
DCS
BS
Burner Flame Detector Switch
DI
FLD
2 Wire Switch (NO) To JB
BS
Burner Switch
DI
FLD
2 Wire Switch (NO) To JB
BS
Heat Detector
DCS DI
FLD
2 Wire Switch (NO) To JB
FLD
BZS
Flame Detector Switch
DI
FLD
2 Wire Switch (NO) To JB
BZT
Flame Detector
DI
FLD
2 Wire Switch (NO) To JB
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
of
Operatin g Principle
Hook up Type
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
Functi on FAH
Description
I/O Type
Locati on
Flow Alarm High
DCS
Flow Alarm High High
DCS
FAL
Flow Alarm Low
DCS
FALL
Flow Alarm Low Low
DCS
FC
Flow Controller
DCS
FE
Averaging Pitot Tube Element
FLD
FE
Coriolis Flow Element
FLD
FE
Orifice Plate
FLD
FE
Thermal/Mass Flow Element
FLD
FE
Turbine Flow Element
FLD
FE
Ultrasonic Flow Element
FLD
FE
Venturi Tube Flow Element
FLD
FE
Vortex Flow Element
FLD
Controller (Flow Ratio)
DCS
FG
DP Flow Gauge
FLD
FG
DP Flow Gauge
FLD
FI
Flow Indicator
DCS
FI
Flow Indicator - Local
FAHH
FFIC
AO
FLD
FIC
Controller
DCS
FIC
Local Controller
FLD
FIT
Flow Indicating Transmitter
FQI
Local Totallised Flow Indicator
FLD
FQI
Totallised Flow Indicator
DCS
Local Flow Totaliser Controller
FLD
FQIC
AI
FLD
I/P To JB
2 Wire Tx To JB
Coriolis Flow Transmitter
AI
FLD
2 Wire Tx To JB
FT
DP Flow Transmitter
AI
FLD
2 Wire Tx To JB
FT
Pitot Tube Flow Transmitter
AI
FLD
2 Wire Tx To JB
FT
Thermal/Mass Flow Meter
FLD
FT
Turbine Flowmeter
FLD
FT
Ultrasonic Flow Transmitter
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
FLD
: 45
Rev.
: A
Date
: 26-Feb-2013
Wiring Rule
FT
AI
Page
2 Wire Tx To JB
Operatin g Principle
of
53
Hook up Type
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
Functi on
Description
I/O Type
Locati on
AI
FLD
Page
: 46
Rev.
: A
Date
: 26-Feb-2013
Wiring Rule
FT
Vortex Flow Transmitter
FV
Control Valve
FV
Control Valve (with I/P)
AO
FLD
I/P To JB
FY
I/P Converter
AO
FLD
I/P To JB
FZS
Flow Switch
DI
FLD
2 Wire Switch (NO) To JB
FZSL
Flow Switch
DI
FLD
2 Wire Switch (NO) To JB
FZT
DP Flow Transmitter
AI
FLD
2 Wire Tx To JB
HC
Controller
DCS
HCV
Hand Control Valve
FLD
HCV
Hand Control Valve
FLD
HIC
Hand Controller
DCS
HS
Duty Select
DCS
HS
Hand Switch
HS
Hand Switch - Remote
HS
Hand Switch (local Control)
HS
Local Isolator
HS
Local Start Switch
DI
FLD
2 Wire Switch (NO) To JB
HS
Manual Field Reset Switch
DI
FLD
2 Wire Switch (NO) To JB
HV
Control Valve
HV
Control Valve (with I/P)
HV
Hand Valve
FLD
LAH
Level Alarm High
DCS
Level Alarm High High
DCS
LAL
Level Alarm Low
DCS
LALL
Level Alarm Low Low
DCS
Level Gauge
FLD
LAHH
LG
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
2 Wire Tx To JB
FLD
DI
FLD
2 Wire Switch (NO) To JB
DCS DI
FLD
2 Wire Switch (NO) To JB
FLD
FLD AO
FLD
I/P To JB
Operatin g Principle
of
53
Hook up Type
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
Functi on
Description
I/O Type
Locati on
Page
: 47
Rev.
: A
Date
: 26-Feb-2013
Wiring Rule
LI
Level Indicator
DCS
LI
Level Indicator - Local
AO
FLD
I/P To JB
LI
Local Indicator
AO
FLD
I/P To JB
LIC
Controller
LSH
Level Switch High
DI
FLD
2 Wire Switch (NO) To JB
Level Switch High High
DI
FLD
2 Wire Switch (NO) To JB
LSL
Level Switch Low
DI
FLD
2 Wire Switch (NO) To JB
LSLL
Level Switch Low Low
DI
FLD
2 Wire Switch (NO) To JB
LT
DP Level Transmitter
AI
FLD
2 Wire Tx To JB
LT
Level Transmitter - Displacer Type
AI
FLD
2 Wire Tx To JB
LV
Control Valve
LV
Control Valve (with I/P)
AO
FLD
I/P To JB
LY
I/P Converter
AO
FLD
I/P To JB
LSHH
PAH
DCS
FLD
Pressure Alarm High
DCS
Pressure Alarm High High
DCS
PAL
Pressure Alarm Low
DCS
PALL
Pressure Alarm Low Low
DCS
PCV
Pressure Regulating Valve
FLD
PCV
Pressure Regulator - Downstream Sensing
FLD
PCV
Pressure Regulator - Pilot
FLD
PDAH
Diff Pressure Alarm High
DCS
PDAH H
Diff Pressure Alarm High High
DCS
PDAL
Diff Pressure Alarm Low
DCS
PDG
Diff Pressure Gauge
FLD
PDI
Indicator
DCS
Indicating Controller
DCS
PAHH
PDIC
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
Operatin g Principle
of
53
Hook up Type
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
Functi on
Page
: 48
Rev.
: A
Date
: 26-Feb-2013
I/O Type
Locati on
Diff Pressure Switch
DI
FLD
2 Wire Switch (NO) To JB
PDT
Diff Pressure Transmitter
AI
FLD
2 Wire Tx To JB
PDY
Dcs Selector
DCS
PG
Pressure Gauge
FLD
PI
Indicator
DCS
PIC
Indicating Controller
DCS
PIC
Local Controller
FLD
PSH
Pressure Switch High
DI
FLD
2 Wire Switch (NO) To JB
Pressure Switch High High
DI
FLD
2 Wire Switch (NO) To JB
PSL
Pressure Switch Low
DI
FLD
2 Wire Switch (NO) To JB
PSLL
Pressure Switch Low Low
DI
FLD
2 Wire Switch (NO) To JB
PSV
Pressure / Vacuum Relief Valve
FLD
PSV
Safety Relief Valve
FLD
PSV
Vacuum Relief Valve
FLD
PT
Pressure Transmitter
PV
Control Valve
PV
Control Valve (with I/P)
AO
FLD
I/P To JB
PY
I/P Converter
AO
FLD
I/P To JB
PZSH
Pressure Switch High
DI
FLD
2 Wire Switch (NO) To JB
PZSL
Pressure Switch Low
DI
FLD
2 Wire Switch (NO) To JB
PZT
Pressure Transmitter
AI
FLD
2 Wire Tx To JB
PZT
Pressure Transmitter
AI
FLD
2 Wire Tx To JB
RO
Restriction Orifice
FLD
SI
Speed Indicator
DCS
SIC
Speed Controller
DCS
ST
Speed Transmitter
PDSH
PSHH
Description
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
AI
FLD
Wiring Rule
2 Wire Tx To JB
FLD
AI
FLD
2 Wire Tx To JB
Operatin g Principle
of
53
Hook up Type
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
Functi on SY
Description I/P Converter
I/O Type
Locati on
AO
FLD
Page
: 49
Rev.
: A
Date
: 26-Feb-2013
Wiring Rule I/P To JB
TAH
Local Alarm
DCS
TAH
Temperature Alarm High
DCS
Temperature Alarm High High
DCS
TAL
Temperature Alarm Low
DCS
TALL
Temperature Alarm Low Low
DCS
TE
Rtd Temperature Element
FLD
TE
Rtd Temperature Element (direct)
RTD
FLD
TE
Thermocouple Element - Type J (direct)
T/C
FLD
T/C (type J) To JB
TE
Thermocouple Element - Type K (direct)
T/C
FLD
T/C (type K) To JB
TE
Thermocouple Temperature Element
FLD
TG
Temperature Gauge
FLD
TI
Temperature Indicator
DCS
TI
Temperature Indicator (local)
FLD
TIC
Controller
DCS
TIC
Indicating Controller
DCS
TSH
Temperature Switch High
DI
FLD
2 Wire Switch (NO) To JB
Temperature Switch High High
DI
FLD
2 Wire Switch (NO) To JB
TSL
Temperature Switch Low
DI
FLD
2 Wire Switch (NO) To JB
TSLL
Temperature Switch Low High
DI
FLD
2 Wire Switch (NO) To JB
TSV
Solenoid Valve
AO
FLD
I/P To JB
TT
Temperature Transmitter
AI
FLD
2 Wire Tx To JB
TV
Control Valve
TV
Control Valve (with I/P)
TW
Thermowell
TY
I/P Converter
TAHH
TSHH
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
FLD AO
FLD
I/P To JB
FLD AO
FLD
I/P To JB
Operatin g Principle
of
53
Hook up Type
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
Functi on
Description
I/O Type
Locati on
AI
FLD
Page
: 50
Rev.
: A
Date
: 26-Feb-2013
Wiring Rule
TZT
Temperature Transmitter
UA
Alarm
DCS
UC
Duty Controller
DCS
VAHH
Vibration Alarm
DCS
Indicator
DCS
VSH
Vibration Alarm
DCS
VSH
Vibration Switch
DI
FLD
2 Wire Switch (NO) To JB
VSHH
Vibration Switch
DI
FLD
2 Wire Switch (NO) To JB
WT
Weight Transmitter
AI
FLD
2 Wire Tx To JB
XA
Common Alarm
DCS
XI
Indicator
DCS
XI
Motor Status
DCS
XS
Local Switch
DI
FLD
2 Wire Switch (NO) To JB
XS
Switch
DI
FLD
2 Wire Switch (NO) To JB
VI
2 Wire Tx To JB
XSV
Pilot Valve
XSV
Solenoid Valve
DO
FLD
XV
On/off Valve
DO
FLD
XV
Shutdown Valve
XV
Shutdown Valve - Motorised
DO
FLD
XZV
Shutdown Valve
DO
FLD
XZV
Solenoid Valve
DO
FLD
ZIC
Valve Closed Indicator
DCS
ZIO
Valve Open Indicator
DCS
ZSC
Valve Closed Limit Switch
DI
FLD
2 Wire Switch (NO) To JB
ZSC
Valve Closed Proximity Switch
DI
FLD
2 Wire Switch (NO) To JB
ZSO
Valve Open Limit Switch
DI
FLD
2 Wire Switch (NO) To JB
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
FLD
FLD
Operatin g Principle
of
53
Hook up Type
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
Functi on ZSO
Description
Valve Open Proximity Switch
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
I/O Type
Locati on
DI
FLD
Page
: 51
Rev.
: A
Date
: 26-Feb-2013
Wiring Rule 2 Wire Switch (NO) To JB
Operatin g Principle
of
53
Hook up Type
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
Appendix C -
Page
: 52
Rev.
: A
Date
: 26-Feb-2013
List of Instrument Datasheet forms
Form Name
Description
AD0001
Datasheet for HIPPS Shutdown Valves
AD0002
Datasheet for Pressure Transmitters - HIPPS
AD0003
Datasheet for Safety Relief Valve
AD0004
Datasheet for Shutdown Valve
AD0005
Datasheet for Flow Element – Pitot Tube
AD0006
Datasheet for Level Transmitter (GWR) Internal with Level Gauge
AD0007
Datasheet for Differential Pressure Transmitter
AD0008
Datasheet for Differential Pressure Transmitter (Flow)
AD0009
Datasheet for Temperature Transmitter
AD0010
Datasheet for Control Valve
AD0011
Datasheet for Motor Operated Valve
AD0012
Datasheet for Flow Element – Orifice Plate
AD0013
Datasheet for Pressure Transmitter
AD0014
Datasheet for Flow Element – Restriction Orifice
AD0015
Datasheet for Temperature Element with Thermowell
AD0016
Datasheet for Pressure Gauge
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
of
53
ADXXX-XX-I-05000 SPECIFICATION FOR INSTRUMENT DATABASE (AVEVA INSTRUMENTATION)
Attachment 1 – Instrument Datasheets (Total 18 sheets)
ADMA OPCO Contract No : 155436 ASBUILT PROJECT FOR USSC AND DAS ISLAND
Page
: 53
of
53
Rev.
: A
Date
: 26-Feb-2013
View more...
Comments
