Polydoros LX SX PDF
February 8, 2023 | Author: Anonymous | Category: N/A
Short Description
Download Polydoros LX SX PDF...
Description
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
GE Medi Medical cal Systems Sys tems
g
MVS DI EUROPE
Technical Publications
POLYDOROS LX/SX new Family
2305147-100
Revision 3
sm Service Manual
Do not duplicate
Copyright
2004 GE Medical System
Al ig nm nment ent
Com Compo po nent
Cal i b r at i o n L o c at i o n s Written by: E. de Schuttelaere
Err or Co d es
Fun ct io nal
Lo gic/B gi c/B lo ck
Prev Prevent entiv iv e
Softw Sof tw are
Theo Theory ry
Servic Serv ic e
Ch ec k s D Dii ag r am s Mai n t en an c e Di ag n o s t i c s n o t es controlled by: J.Aupied 1 of 288 formatted by: E. de Schuttelaere
Refer Referenc ence e
Not es
Mat er i al s date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
CONTENTS CHAPTER
TITLE
ALIGNEMENT / CALIBRATION CALIBRATION
Introduction Introduction
278 PaPAGE e 14 o13 f of 28 288 8278
Glos Glossar sary y… Cuckoo Configuration BEFORE Site Job……… Cuckoo Use on Site ………..……
PaPAGE e 15 o14 f of 28 288 8278 278 PaPAGE e 16 o15 f of 28 288 8278
Job Cards using Cuckoo-XCU software connection
278 PaPAGE e 19 o18 f of 28 288 8278
Job Cards using Cuckoo-Polydoros software connection
PaPAGE e 28 o28 f of 28 288 8278
Other job cards (not frequently used) with OEM software
278 PaPAGE e 80 o73 f of 28 288 8278
Com plementary information
PaPAGE e 98 o91 f of 28 288 8278
Al ig nm nment ent
Com Compo po nent
Cal i b r at i o n L o c at i o n s Written by: E. de Schuttelaere
Err or Co d es
Fun ct io nal
Pages / links
Lo gic/B gi c/B lo ck
Prev Prevent entiv iv e
Softw Sof tw are
278 PaPAGE e 18 o17 f of 28 288 8278
Theo Theory ry
Servic Serv ic e
Ch ec k s D Dii ag r am s Mai n t en an c e Di ag n o s t i c s n o t es controlled by: J.Aupied 2 of 288 formatted by: E. de Schuttelaere
Refer Referenc ence e
Not es
Mat er i al s date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
CONTENTS CHAPTER
TITLE
COMPONENT LOCATION
LX Master board D100
278 278 PPAGE a e 10 104 497ofof 2 288 88
LX HT module D110 ; D115 andD220……………………
278 278 PPAGE a e 10 105 598ofof 2 288 88
LX Power connection……………………………………
278 278 PPAGE a e 10 106 699ofof 2 288 88
LX KK Interface and D160 board…………………………………..
100ofof 2 278 278 PPAGE a e 10 107 7 288 88
Al ig nm nment ent
Com Compo po nent
Cal i b r at i o n L o c at i o n s Written by: E. de Schuttelaere
Err or Co d es
Fun ct io nal
Pages / links
Lo gic/B gi c/B lo ck
Prev Prevent entiv iv e
Softw Sof tw are
Theo Theory ry
Servic Serv ic e
Ch ec k s D Dii ag r am s Mai n t en an c e Di ag n o s t i c s n o t es controlled by: J.Aupied 3 of 288 formatted by: E. de Schuttelaere
Refer Referenc ence e
Not es
Mat er i al s date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
CONTENTS CHAPTER
TITLE
Pages / links
ERROR CODES CODES
Errors Display Rules…………
101ofof 2 278 278 PPAGE a e 10 108 8 288 88 PAGE109 102ofof 288 278 Page 106ofof 2 278 278 PPAGE a e 11 113 3 288 88
HOW to TROUBLE SHOOT LX35/50/Lite BOOT LX ERRORS…………………………………..… ERRORS…………………………………..… Consol Other…………………………………………..
Download Errors…………………………
106ofof 2 278 278 PPAGE a e 11 113 3 288 88 107ofof 2 278 278 PPAGE a e 11 114 4 288 88 108ofof 2 278 PPAGE a e 11 115 5 288 88 113ofof 2 278 PPAGE a e 12 120 0 288 88 114ofof 2 278 PPAGE a e 12 121 1 288 88 PAGE 114 of 278 Pa e 12 121 1 of 2 288 88
Iontomat PL:……………………… Power pack:………………………..
115ofof 2 278 278 PPAGE a e 12 122 2 288 88 116ofof 288 278 278 PAGE123 Page
SX ERRORS…………………………………..… ERRORS…………………………………..…
Iontomat PL
125ofof 2 278 278 PPAGE a e 13 132 2 288 88 125ofof 2 278 278 PPAGE a e 13 132 2 288 88 128ofof 2 278 278 PPAGE a e 13 135 5 288 88 PAGE 129 of 278 278 Pa e 13 136 6 of 2 288 88 PAGE138 131ofof 288 278 278 Page 132ofof 2 278 278 PPAGE a e 13 139 9 288 88 133ofof 2 278 278 PPAGE a e 14 140 0 288 88 PAGE 134 of 278 278 Pa e 14 141 1 of 2 288 88
Power Supplies and High Voltage Tube and Anode Starter
137ofof 2 278 278 PPAGE a e 14 144 4 288 88 152ofof 2 278 278 PPAGE a e 15 159 9 288 88
Filament…………………………… Voltage supplies………………… Fila Filam ment Inv Inverte erter… r……… ………. …...…… ………… ………… ……
Errors from 000 to 100 Filament Iontomat and Filament D220 power Supply Filament Inverte Inverter r Download ad Filament Downlo
Al ig nm nment ent
Com Compo po nent
Cal i b r at i o n L o c at i o n s Written by: E. de Schuttelaere
Err or Co d es
Fun ct io nal
Lo gic/B gi c/B lo ck
Prev Prevent entiv iv e
Softw Sof tw are
Theo Theory ry
Servic Serv ic e
Ch ec k s D Dii ag r am s Mai n t en an c e Di ag n o s t i c s n o t es controlled by: J.Aupied 4 of 288 formatted by: E. de Schuttelaere
Refer Referenc ence e
Not es
Mat er i al s date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
CONTENTS CHAPTER
TITLE
FUNCTIONAL CHECKS
Al ig nm nment ent
Com Compo po nent
Cal i b r at i o n L o c at i o n s Written by: E. de Schuttelaere
Err or Co d es
Pages / links
Central Listing…….…………………………………… Abbreviations and Symbols………………………………… Leds and N90 Display…………………………………… Main Functions Explanations…………………………………….. Show data……………………………………………
157o of 28 278 278 PPAGE a e 1 16 65 8 161ofof 2 278 278 PPAGE a e 16 169 9 288 88 PPAGE a e 1 17 70 8 162o of 28 278 278 164o of 28 278 278 PPAGE a e 1 17 72 8 PPAGE a e 1 17 74 8 166o of 28 278 278
Unit selection…………………………………….. Fluoroscopy Parameters………………………………….. Videomatic P / PE………………………………….. High contrast fluoroscopy…………………………… Digital Radiography Parameters…………….…………………………… Option………………….…………………………… Default organ program…………………………….. Organ program…………………………………….. Iontomat and Screen-Film Couples…………………………………………….. Fluoroscopy Curves…………………………………….. Exposure Curves…………………………………….. Other Data…………………………………………….. How data are saved……………………….…………..
166 of 8 278 278 PAGE P a 1 17 74 8 168o 278 278 PPAGE a e e 17 176 6 ofof 2 2 288 88 170o of 28 278 278 PPAGE a e 1 17 78 8 PPAGE a e 17 179 9 288 88 171ofof 2 278 172ofof 2 278 PPAGE a e 18 180 0 288 88 PPAGE a e 1 18 81 8 173o of 28 278 PPAGE a e 1 18 82 8 174o of 28 278 278 175o of 28 278 278 PPAGE a e 1 18 83 8 177 of 278 PAGE Pa e 18 185 5 of 2 288 88 181o of 28 278 PPAGE a e 1 18 89 8 PPAGE a e 1 19 90 8 182o of 28 278 PPAGE a e 1 19 92 8 184o of 28 278 278 186ofof 2 278 278 PPAGE a e 19 194 4 288 88
Tube and Radiological Data…………………………………………….... KK system configuration……………………………. Site structure………………………………………... Unit Data………………………………………………….. Fluoroscopy / DR unit#1 – radiography - sircam…………………. Option……….………………………………………..
188o of 28 278 278 PPAGE a e 1 19 96 8 194ofof 2 278 278 PPAGE a e 20 202 2 288 88 PPAGE a e 2 20 03 8 195o of 28 278 278 197ofof 2 278 278 PPAGE a e 20 205 5 288 88 199ofof 2 278 278 PPAGE a e 20 207 7 288 88 201o of 28 278 PPAGE a e 2 20 09 8
Tubes Data / Do Dose se Rates………………….. TV iris diaphragm………………..
202ofof 2 278 278 PPAGE a e 21 210 0 288 88 203o of 28 278 PPAGE a e 2 21 11 8
Fun ct io nal
Lo gic/B gi c/B lo ck
Prev Prevent entiv iv e
Softw Sof tw are
Theo Theory ry
Servic Serv ic e
Ch ec k s D Dii ag r am s Mai n t en an c e Di ag n o s t i c s n o t es controlled by: J.Aupied 5 of 288 formatted by: E. de Schuttelaere
Refer Referenc ence e
Not es
Mat er i al s date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
CONTENTS CHAPTER
TITLE
LOGIC / BLOCK DIAGRAMS
Bloc Diagrams (LX then SX)…………………
PAGE212 204ofof 288 278 278 Page
Power cabinet (LX then SX)……………………………
206ofof 2 278 278 PPAGE a e 21 214 4 288 88
Wiring MisMap (LX then SX)………………..
208ofof 2 278 278 PPAGE a e 21 217 7 288 88
Power line connection (LX then SX)………………………………
210ofof 2 278 278 PPAGE a e 21 219 9 288 88
External connections (LX then SX)………………………………..
212ofof 2 278 278 PPAGE a e 22 221 1 288 88
Main power supply (LX then SX)………………………………….
214ofof 2 278 PPAGE a e 22 223 3 288 88
KV control………………………………………….. Inverters………………………………………………
216ofof 2 278 278 PPAGE a e 22 225 5 288 88 217ofof 2 278 278 PPAGE a e 22 226 6 288 88
High Voltage Circuit………………………………
218ofof 2 278 278 PPAGE a e 22 227 7 288 88
Filament Drive…………………………..
219ofof 2 278 278 PPAGE a e 22 228 8 288 88
Master Board D100 (LX then SX)…………………………………….
220ofof 2 278 278 PPAGE a e 23 230 0 288 88
Safety circuit (LX then SX)………………………
222ofof 2 278 278 PPAGE a e 23 232 2 288 88
Control console………………………………………
224ofof 288 278 278 PAGE234 Page
Iontomat (LX then SX)……………………………….
226ofof 2 278 278 PPAGE a e 23 236 6 288 88
Anode starter…………………………………
229ofof 2 278 278 PPAGE a e 23 239 9 288 88
XCU System Processor (LX then SX)…………………………………….
230ofof 2 278 278 PPAGE a e 24 240 0 288 88
KK interface board(LX then SX)…………………………………………
232ofof 2 278 278 PPAGE a e 24 242 2 288 88
Fun ct io nal
Refer Referenc ence e
Al ig nm nment ent
Com Compo po nent
Cal i b r at i o n L o c at i o n s Written by: E. de Schuttelaere
Err or Co d es
Pages / links
Lo gic/B gi c/B lo ck
Prev Prevent entiv iv e
Softw Sof tw are
Theo Theory ry
Servic Serv ic e
Ch ec k s D Dii ag r am s Mai n t en an c e Di ag n o s t i c s n o t es controlled by: J.Aupied 6 of 288 formatted by: E. de Schuttelaere
Not es
Mat er i al s date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
CONTENTS CHAPTER
TITLE
Pages / links
PREVENTIVE MAINTENANCE
Proceed with:
PREVENTIVE MAINTENANCE MAINTENANCE service tool Ref: 2376009-200 DVD
Al ig nm nment ent
Com Compo po nent
Cal i b r at i o n L o c at i o n s Written by: E. de Schuttelaere
Err or Co d es
Fun ct io nal
Lo gic/B gi c/B lo ck
(PM version 2 or higher)
Prev Prevent entiv iv e
Softw Sof tw are
Theo Theory ry
Servic Serv ic e
Ch ec k s D Dii ag r am s Mai n t en an c e Di ag n o s t i c s n o t es controlled by: J.Aupied 7 of 288 formatted by: E. de Schuttelaere
Refer Referenc ence e
Not es
Mat er i al s date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
CONTENTS CHAPTER
TITLE
SOFTWARE DIAGNOSTICS
Old software list for Polydoros LX……….…………………………..
Al ig nm nment ent
Com Compo po nent
Cal i b r at i o n L o c at i o n s Written by: E. de Schuttelaere
Err or Co d es
Fun ct io nal
Pages / links
Lo gic/B gi c/B lo ck
Prev Prevent entiv iv e
Softw Sof tw are
Theo Theory ry
234ofof 2 278 PPAGE a e 24 244 4 288 88
Servic Serv ic e
Ch ec k s D Dii ag r am s Mai n t en an c e Di ag n o s t i c s n o t es controlled by: J.Aupied 8 of 288 formatted by: E. de Schuttelaere
Refer Referenc ence e
Not es
Mat er i al s date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
CONTENTS
CHAPTER
TITLE
THEORY
Polydoros LX/SX new Family Presentation
236ofof 2 278 278 PPAGE a e 24 246 6 288 88
Product Document Explanation
237ofof 2 278 278 PPAGE a e 24 247 7 288 88
Interconnectio Interco nnection n Drawing Drawing
238ofof 2 278 278 PPAGE a e 24 248 8 288 88
Annota otatio tions ns Documents Ann
239ofof 2 278 278 PPAGE a e 24 249 9 288 88
Com patibility Table
240ofof 2 278 278 PPAGE a e 25 250 0 288 88
Connectors Layou Connectors Layoutt Cable connection KK1A (g1-g2) ; KK1A (g3-g5)….. ( g3-g5)…..
241ofof 2 278 278 PPAGE a e 25 251 1 288 88 242ofof 2 278 278 PPAGE a e 25 252 2 288 88
Cable connection KK1B (g1-g2) ; KK1B (g3-g5)….. ( g3-g5)…..
244ofof 2 278 278 PPAGE a e 25 254 4 288 88
Cable connection KK2 ……………………
246ofof 2 278 278 PPAGE a e 25 256 6 288 88
Al ig nm nment ent
Com Compo po nent
Cal i b r at i o n L o c at i o n s Written by: E. de Schuttelaere
Err or Co d es
Fun ct io nal
Pages / links
Lo gic/B gi c/B lo ck
Prev Prevent entiv iv e
Softw Sof tw are
Theo Theory ry
Servic Serv ic e
Ch ec k s D Dii ag r am s Mai n t en an c e Di ag n o s t i c s n o t es controlled by: J.Aupied 9 of 288 formatted by: E. de Schuttelaere
Refer Referenc ence e
Not es
Mat er i al s date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
CONTENTS
CHAPTER
TITLE
SERVICE NOTES
Update of D110 in case of error 711…………………
247ofof 2 278 278 PPAGE a e 25 257 7 288 88
New filament board D220……………………………
248ofof 2 278 278 PPAGE a e 25 258 8 288 88
Sporadic error 550……………………………………
250ofof 2 278 278 PPAGE a e 26 260 0 288 88
Error 550 caused by operator……………………….
252ofof 2 278 278 PPAGE a e 26 262 2 288 88
Control console failure………………………………
253ofof 2 278 278 PPAGE a e 26 263 3 288 88
Density correction…………………………………… RX tubes information………………………………..
255ofof 2 278 278 PPAGE a e 26 265 5 288 88 256ofof 2 278 278 PPAGE a e 26 266 6 288 88
Al ig nm nment ent
Com Compo po nent
Cal i b r at i o n L o c at i o n s Written by: E. de Schuttelaere
Err or Co d es
Fun ct io nal
Pages / links
Lo gic/B gi c/B lo ck
Prev Prevent entiv iv e
Softw Sof tw are
Theo Theory ry
Servic Serv ic e
Ch ec k s D Dii ag r am s Mai n t en an c e Di ag n o s t i c s n o t es controlled by: J.Aupied 10 of 288 formatted by: E. de Schuttelaere
Refer Referenc ence e
Not es
Mat er i al s date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
CONTENTS
CHAPTER
TITLE
REFERENCE MATERIALS
POLYDOROS LX PARTS PARTS
260ofof 2 278 278 PPAGE a e 27 270 0 288 88
CPU master board LX Inverter circuit LX …
260ofof 288 278 278 PAGE270 Page PAGE 261 of 278 278 Pa e 27 271 1 of 2 288 88
Line connection circuit LX…
262ofof 2 278 278 PPAGE a e 27 272 2 288 88
Cons Consol olee LX
263ofof 2 278 PPAGE a e 27 273 3 288 88
POLYDOROS SX PARTS PARTS
264ofof 2 278 278 PPAGE a e 27 274 4 288 88
Main Cabinet SX
264ofof 2 278 278 PPAGE a e 27 274 4 288 88
M16 Power Unit and KK Interface
267ofof 2 278 278 PPAGE a e 27 276 6 288 88
Fluoro Option and Anode Starter
268ofof 2 278 278 PPAGE a e 27 278 8 288 88
Fun ct io nal Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are Theo Theory ry Servic Serv ic e Ch ec k s D Dii ag r am s Mai n t en an c e Di ag n o s t i c s n o t es controlled by: J.Aupied 11 of 288 formatted by: E. de Schuttelaere
Refer Referenc ence e Not es Mat er i al s date 27-Sept-2004
Al ig nm nment ent Com Compo po nent Cal i b r at i o n L o c at i o n s Written by: E. de Schuttelaere
Err or Co d es
Pages / links
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
CONTENTS CHAPTER
TITLE
NOTES
WARNING
Pa PAGE e 27 279 9 269 of of2 288 88 278 278
X–RAY PROTECTION PROTECTION
Pa PAGE e 28 280 0 270 of of2 288 88 278
LIST OF RISK ASSESSMENTS FOR X-RAY PM
Page PAGE 281 271 of of288278 278
REVISION REVIS ION HISTO HISTORY RY
278 Pa PAGE e 28 288 8 278 of of2 288 88
Al ig nm nment ent Com Compo po nent Cal i b r at i o n L o c at i o n s Written by: E. de Schuttelaere
Err or Co d es
Fun ct io nal Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are Theo Theory ry Servic Serv ic e Ch ec k s D Dii ag r am s Mai n t en an c e Di ag n o s t i c s n o t es controlled by: J.Aupied 12 of 288 formatted by: E. de Schuttelaere
Pages / links
Refer Referenc ence e Not es Mat er i al s date 27-Sept-2004
Written by: E. de Schuttelaere
controlled by: J.Aupied
12 of 288
formatted by: E. de Schuttelaere
date 27 Sept 2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
General Safety Instructions
WARNINGS : Following PGS19 only OEM (Siemens) Parts or OPM ( Original Part Manufacturer ; in example SDS for an SDS relay ) parts must be used except on specific programs developped by MVSDI Engineer Engineer Central Team (in example: X-Ray Tubes). Only the original oils defined by OEM must be used and all accessories must be ordered from Philips only. Chemical capacitor must be discharged before any intervention. The shunt must stay on the capacitor because some capacitors are able to retore a charge when left in open circuit.
Mandatory checks : Those tests must be performed after each corrective or preventive maintenance on relevant circuits: o o o o
o
Check X-Ray-Tube and check that there is not leakage or HT Tank oil leakage Check safety switch over temperature on X-Ray Tube and flow switch on cooling unit (if present) are functional. Check all grounds are connected on X-Ray Tubes , collimator , covers. Check KV & mAs displayed are identical to KV & mAs measured: o Check 50KV , 100KV , 125KV o Check 10mAS , 100mAS , 350 mAS ( in Large Focus ) Check heating circuit
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
Not es
Written by: E. de Schuttelaere
controlled by: J.Aupied
13 of 288
formatted by: E. de Schuttelaere
date 27 Sept 2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Introduction That section explains how calibrated and test the system with Cuckoo software and at the end you also have other information. That section includes 4 main sections (after glossary section next page) :
Al ig nm nment ent Cal i b r at i o n
o
#1 Cuckoo configuration before site job
o
#2 Cuckoo use on site
o
#3 Job cards using “Cuckoo–XCU software”
o o
#4 Job cards using “Cuckoo–Polydoros software” #5 Other job cards (not frequently used) with “OEM software”
o
#6 Complementary Information
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
Not es
Written by: E. de Schuttelaere
controlled by: J.Aupied
14 of 288
formatted by: E. de Schuttelaere
date 27 Sept 2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Glossary XCU: Central control unit for XCS ARCNET based system network (High end XCU with hard disk and low end XCU without hard disk) XCU: Central
CAN: Control Area Network. Component connected to CAN are: CAN: Control o XCU o BUC o Remote Control console o Collimator o Vertix Pro/Top o CAN termination are on the XCU and the collimator
SW: Software HW: Hardware HW: Hardware
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
Not es
Written by: E. de Schuttelaere
controlled by: J.Aupied
15 of 288
formatted by: E. de Schuttelaere
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
#1 : Cuckoo Configuration BEFORE Site Job
you must ask install the Cuckoo software on your laptop with the DVD 2376009-X then ask for a license number. site you Before to go on site connection.. Note: It will need a mail connection Note: An example of configuration is given next page (numbers are wrong and can’t be used) : At the first Cuckoo start you will have this screen. Type your 7 digit USERID (here it’s “USERIDI”)
Then click on “License key”.
You will have this screen :
o o o
Then click send registration and send the mail. You will receive a response with the Key Enter it in the “Key” field then click on “Validation”
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
Not es
Written by: E. de Schuttelaere
controlled by: J.Aupied
16 of 288
formatted by: E. de Schuttelaere
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
o
Choose your password More information available in the following document :
Cuckoo 3rd party diagnostics SW : 2337175-100 It’s included into the CUCKOO the CUCKOO software package under filename : USERMANUAL.doc filename :
Enter it again in the “PASSWORD” field of the login. CUCKOO is ready to run.
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
Not es
Written by: E. de Schuttelaere
controlled by: J.Aupied
17 of 288
formatted by: E. de Schuttelaere
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
#2 Cuckoo Use on Site o o o
First connect the service laptop to the XCU. Then launch the CUCKOO SOFTWARE. Enter your USERID and your PASSWORD then choose the System : XCU
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
Not es
Written by: E. de Schuttelaere
controlled by: J.Aupied
18 of 288
formatted by: E. de Schuttelaere
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
#3 Job cards using Cuckoo– XCU software connection
Following Job Cards are done with that connection
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
Not es
Written by: E. de Schuttelaere
controlled by: J.Aupied
19 of 288
formatted by: E. de Schuttelaere
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Reading out the software releases
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
Not es
Written by: E. de Schuttelaere
controlled by: J.Aupied
20 of 288
formatted by: E. de Schuttelaere
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Reading out the error log memory
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
Not es
Written by: E. de Schuttelaere
controlled by: J.Aupied
21 of 288
formatted by: E. de Schuttelaere
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Reading out the tube statistics
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
Not es
Written by: E. de Schuttelaere
controlled by: J.Aupied
22 of 288
formatted by: E. de Schuttelaere
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Back-up system data
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
Not es
Written by: E. de Schuttelaere
controlled by: J.Aupied
23 of 288
formatted by: E. de Schuttelaere
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
Not es
Written by: E. de Schuttelaere
controlled by: J.Aupied
24 of 288
formatted by: E. de Schuttelaere
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
Not es
Written by: E. de Schuttelaere
controlled by: J.Aupied
25 of 288
formatted by: E. de Schuttelaere
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Restore system data
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
Not es
Written by: E. de Schuttelaere
controlled by: J.Aupied
26 of 288
formatted by: E. de Schuttelaere
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
Not es
Written by: E. de Schuttelaere
controlled by: J.Aupied
27 of 288
formatted by: E. de Schuttelaere
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
#4 Job cards using Cuck Cuckoo oo– – Polydoros software connection Followin Fol ing g Jo Job Ca Card rdss are done with that connection
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
Not es
Written by: E. de Schuttelaere
controlled by: J.Aupied
28 of 288
formatted by: E. de Schuttelaere
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
TUBE ADAPTATION
The following procedure details the instal lation/calibration of the tube using software and measurement tools. Note : that procedure can be applied when the original tube is replaced by an equivalent tube. It’s divided in 6 steps : St ep 1 :: Meters Meters installati on
1. Meters installation
XCU selected
2. Tube configuration
Polydoros LX / Tube adaptation Polydo ros L X / SX SX Tube adaptatio adaptatio n selected
3. Warm Up
St ep 2 : Tube : Tube configuration: configuration: Select the appropriate X-Ray Tube connected to the generator. The software will use the tube curves stored in the generator for adjustment. menu The adjust adjustment ment is do ne in the XCU menu
Stop X-ray X-ray bu tton 4. Pre-heating Next Next butt on 5. Filament adaptation
St ep s 3 t o 6 : Tu b e ad aptati o n : 3. Warm up 4. Pre-heating
Large focus selection
Ne Next xt butt on 6. Push Current
5 6.. F Piulasm h ecn utrraednat ptation olydor doro s LX LX//SX me menu nu ed i n t h e Poly Th ey ar e p er f o r m
You can use links to navigate
Ne Next xt butt on No
Large focus ad usted ? Yes
Close screen End
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
Not es
Written by: E. de Schuttelaere
controlled by: J.Aupied
29 of 288
formatted by: E. de Schuttelaere
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Step 1: Meters installation 2) Shut dow n the syst em if em if it’s still on. on D220 heating board and D100 master board. Those tools are necessary to check that tools on 3) Install following measurement tools check that is working properly. calibration calibration is o Put a mAs-meter in the mAs b rid ge of D2 D220 20 board (see photo next page) o o o o
Put a voltmeter on board to check the small focus heating (100mv 1A) X18-A2 (F0_RMS) (F0_RMS) of D220 D220 board or Put a voltmeter on board to check the large focus heating (100mv 1A) X18-A3 (F1_RMS) (F1_RMS) of D220 D220 board Put a scope probe on board to check kV (1V 20kV). X61 (KVIST) of D100 D100 board Put a second scope probe on X64 (MAIST) of D100 board D100 board to see mA (1V 200 or 10 or 1mA according to range)
Note : primary high voltage measurement are also available on the D200 board on X18 pins Pin B1 to B8 A1 A2 A3 A4 A5 A6 A7 A8
Name 0V
Signal Ground
Range 0V
VCC F0_RMS F1_RMS mA act F0_INV F1_INV kV+ kV-
LV supply SF heat current LF heat current Tube current inst SF heat. pulses LF heat. pulses. High voltage + High voltage -
+5V 0.1V 1A 0.1V 1A
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
Not es
Written by: E. de Schuttelaere
controlled by: J.Aupied
30 of 288
formatted by: E. de Schuttelaere
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
D220 Heating board
X18 pins
mAs bridge
3) Restart the system on then start configuration (next page).
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
Not es
Cal i b r at i o n
L o c at i o n s
Co d es
Written by: E. de Schuttelaere
Ch ec k s
D Dii ag r am s
controlled by: J.Aupied
Mai n t en an c e Di ag n o s t i c s 31 of 288
n o t es
formatted by: E. de Schuttelaere
Mat er i al s date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Step 2: Tube Configuration
In the main menu select XCU: XCU:
Al ig nm nment ent
Com Compo po nent
Err or
Fun ct io nal
Lo gic/B gi c/B lo ck
Prev Prevent entiv iv e
Softw Sof tw are
Theo Theory ry
Servic Serv ic e
Refer Referenc ence e
Not es
Cal i b r at i o n
L o c at i o n s
Co d es
Written by: E. de Schuttelaere
Ch ec k s
D Dii ag r am s
controlled by: J.Aupied
Mai n t en an c e Di ag n o s t i c s 32 of 288
n o t es
formatted by: E. de Schuttelaere
Mat er i al s date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Select Tubes configuration
Al ig nm nment ent
Com Compo po nent
Err or
Fun ct io nal
Lo gic/B gi c/B lo ck
Prev Prevent entiv iv e
Softw Sof tw are
Theo Theory ry
Servic Serv ic e
Refer Referenc ence e
Not es
Cal i b r at i o n
L o c at i o n s
Co d es
Written by: E. de Schuttelaere
Ch ec k s
D Dii ag r am s
controlled by: J.Aupied
Mai n t en an c e Di ag n o s t i c s 33 of 288
n o t es
Mat er i al s
formatted by: E. de Schuttelaere
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Choose the Tube OPTILIX 150/30/50 HC for Varian Vari an MX100 S600 0610 0610 RG100 RG100 (ref: (ref : MXS61 MXS610.93) 0.93)
Link Return to Overview
Al ig nm nment ent
Com Compo po nent
Err or
Fun ct io nal
Lo gic/B gi c/B lo ck
Prev Prevent entiv iv e
Softw Sof tw are
Theo Theory ry
Servic Serv ic e
Refer Referenc ence e
Not es
Cal i b r at i o n
L o c at i o n s
Co d es
Written by: E. de Schuttelaere
Ch ec k s
D Dii ag r am s
controlled by: J.Aupied
Mai n t en an c e Di ag n o s t i c s 34 of 288
n o t es
formatted by: E. de Schuttelaere
Mat er i al s date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Step 3: Warm-up
Exit fr om th e X XCU CU menu Then select th e gener ator (Polydoros LX or SX)
Al ig nm nment ent
Com Compo po nent
Err or
Fun ct io nal
Lo gic/B gi c/B lo ck
Prev Prevent entiv iv e
Softw Sof tw are
Theo Theory ry
Servic Serv ic e
Refer Referenc ence e
Not es
Cal i b r at i o n
L o c at i o n s
Co d es
Written by: E. de Schuttelaere
Ch ec k s
D Dii ag r am s
controlled by: J.Aupied
Mai n t en an c e Di ag n o s t i c s 35 of 288
n o t es
formatted by: E. de Schuttelaere
Mat er i al s date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
The warm-up is performed in fluoro mode. The warm up duration is around 10 minutes, starting with a low dose rate (70KV, 3 MA) and getting automatically increased until (110KV, 3 MA). The warm up has to be executed only one time, even if you have tDuring wo focus. warm up the fluoro buzzer of the desk is on. Select the appropriate tube to be adjusted with the field Ad field Ad apt ed ttub ub e and click on Start XRY XRY..
Al ig nm nment ent
Com Compo po nent
Err or
Fun ct io nal
Lo gic/B gi c/B lo ck
Prev Prevent entiv iv e
Softw Sof tw are
Theo Theory ry
Servic Serv ic e
Refer Referenc ence e
Not es
Cal i b r at i o n
L o c at i o n s
Co d es
Written by: E. de Schuttelaere
Ch ec k s
D Dii ag r am s
controlled by: J.Aupied
Mai n t en an c e Di ag n o s t i c s 36 of 288
n o t es
formatted by: E. de Schuttelaere
Mat er i al s date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
When X-Ray are ON this logo appears appears
WARNING : If the communication between betwee n Cuckoo and the generator generator fails, the exposure exposur e can can stays on. In such suc h case -> goes out fro m service mode of the th e generator generator The Warm Up is completed when you click on the Stop button or after 10 minutes. The following adjustment is then Pre-heating is Pre-heating selected Overview Link Return to Overview
Al ig nm nment ent
Com Compo po nent
Err or
Fun ct io nal
Lo gic/B gi c/B lo ck
Prev Prevent entiv iv e
Softw Sof tw are
Theo Theory ry
Servic Serv ic e
Refer Referenc ence e
Not es
Cal i b r at i o n
L o c at i o n s
Co d es
Written by: E. de Schuttelaere
Ch ec k s
D Dii ag r am s
controlled by: J.Aupied
Mai n t en an c e Di ag n o s t i c s 37 of 288
n o t es
formatted by: E. de Schuttelaere
Mat er i al s date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Step 4: Pre-heating The preheating (Heating in standby) is adjusted to get a tube current of 1 mA o r 0.2mA. Default values are 70 kV / 1mA for the focus selected in the fluoro mode (small focus) and 110 kV/0.2 mA (LF) One adjustment per focus and tube is necessary. It’s possible possible if you want want to
adjust thetoo preheating currentmanually if it seems high or to low . The correction can reduce (or increase) the heating current by a maximum of 20 %. The focus used in the fluoro is selected by default. o o o
Select the proper tube Select Select the large focus for the 2nd pass Press on Start XRY XRY
Al ig nm nment ent
Com Compo po nent
Err or
Fun ct io nal
Lo gic/B gi c/B lo ck
Prev Prevent entiv iv e
Softw Sof tw are
Theo Theory ry
Servic Serv ic e
Refer Referenc ence e
Not es
Cal i b r at i o n
L o c at i o n s
Co d es
Written by: E. de Schuttelaere
Ch ec k s
D Dii ag r am s
controlled by: J.Aupied
Mai n t en an c e Di ag n o s t i c s 38 of 288
n o t es
formatted by: E. de Schuttelaere
Mat er i al s date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
When the adjustment is done click on Next Next to go to the Filament Ad apt ati on
Link Return to Overview
Al ig nm nment ent
Com Compo po nent
Err or
Fun ct io nal
Lo gic/B gi c/B lo ck
Prev Prevent entiv iv e
Softw Sof tw are
Theo Theory ry
Servic Serv ic e
Refer Referenc ence e
Not es
Cal i b r at i o n
L o c at i o n s
Co d es
Written by: E. de Schuttelaere
Ch ec k s
D Dii ag r am s
controlled by: J.Aupied
Mai n t en an c e Di ag n o s t i c s 39 of 288
n o t es
Mat er i al s
formatted by: E. de Schuttelaere
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Step 5: Filament Adaptation
The objective of the adjustment is to calculate the correction to apply on the curves stored in the generator according to the new Xray tube. Two parameters MUL and ADD allows to make a linear translation. Two exposures are performed with the heating that is store in the PROM second to 60 or 80 % of the load.(High Ma ~ 400 o For the small focus : The first one at 10% (Low MA ~ 50 and ~ 70 KV )and a second at 70KV) second d to 60 or 80 % of the load.(High Ma ~ 640 o For the large focus : The first one at 10% (Low MA ~ 50 and ~ 81 KV )and a secon at 81KV) The parameters of second exposure exposure are determined from the first exposure: exposure: If Ma measures –Ma Expe Expected cted > 20 % then Load percentage=60 %(risk reduced) else load percentage=80% The exposure time is fixed to 0.1s. The KV can be modified if necessary before the first exposure. One adjustment per tube and focus is necessary. The calculation of the two parameter MUL,ADD for the correction is given by: MUL = (Filament current (80/60%) - Filament current (10%) ( 10%) [expected]) / Filament current (80/60%) - Filament current (10%) [measured] ADD = Filament current (10%) [expected] - Filament Filament current (10%) [measured] * MUL
Al ig nm nment ent
Com Compo po nent
Err or
Fun ct io nal
Lo gic/B gi c/B lo ck
Prev Prevent entiv iv e
Softw Sof tw are
Theo Theory ry
Servic Serv ic e
Refer Referenc ence e
Not es
Cal i b r at i o n
L o c at i o n s
Co d es
Written by: E. de Schuttelaere
Ch ec k s
D Dii ag r am s
controlled by: J.Aupied
Mai n t en an c e Di ag n o s t i c s 40 of 288
n o t es
formatted by: E. de Schuttelaere
Mat er i al s date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Select the proper tube and focus if necessary then press on Start XRY
Al ig nm nment ent
Com Compo po nent
Err or
Fun ct io nal
Lo gic/B gi c/B lo ck
Prev Prevent entiv iv e
Softw Sof tw are
Theo Theory ry
Servic Serv ic e
Refer Referenc ence e
Not es
Cal i b r at i o n
L o c at i o n s
Co d es
Written by: E. de Schuttelaere
Ch ec k s
D Dii ag r am s
controlled by: J.Aupied
Mai n t en an c e Di ag n o s t i c s 41 of 288
n o t es
formatted by: E. de Schuttelaere
Mat er i al s date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
After the first exposure the Load percentage is selected automatically according to the difference between expected and real Ma values select.
Press on Start XRY XRY to start the second exposure
Link Return to Overview Overview
Al ig nm nment ent
Com Compo po nent
Err or
Fun ct io nal
Lo gic/B gi c/B lo ck
Prev Prevent entiv iv e
Softw Sof tw are
Theo Theory ry
Servic Serv ic e
Refer Referenc ence e
Not es
Cal i b r at i o n
L o c at i o n s
Co d es
Written by: E. de Schuttelaere
Ch ec k s
D Dii ag r am s
controlled by: J.Aupied
Mai n t en an c e Di ag n o s t i c s 42 of 288
n o t es
formatted by: E. de Schuttelaere
Mat er i al s date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Step 6: Push Current Test
The principle of the Push Current is to boost the filament current. The Push current is determined from iterative procedure in order to have a current value in the range 95%100% of the desired value .It starts at 1.05 and is increased until the current value reaches 95% of the desired mA The Push current calculation is given current by Push = (Filament current (80%)[expected] * Mul + Add )/ (Filament current (80%)[measured] * Mul + Add) The default KV is determined from Filament Adaptation and mA given by internal table. The exposure time is set to 0.1s. Note : One adjustment per tube and focus is necessary.
Al ig nm nment ent
Com Compo po nent
Err or
Fun ct io nal
Lo gic/B gi c/B lo ck
Prev Prevent entiv iv e
Softw Sof tw are
Theo Theory ry
Servic Serv ic e
Refer Referenc ence e
Not es
Cal i b r at i o n
L o c at i o n s
Co d es
Written by: E. de Schuttelaere
Ch ec k s
D Dii ag r am s
controlled by: J.Aupied
Mai n t en an c e Di ag n o s t i c s 43 of 288
n o t es
formatted by: E. de Schuttelaere
Mat er i al s date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Link Return to Overview
If necessary, do the large focus focus with Next Next if not already done or exit exit with A Abo bo r t
Al ig nm nment ent
Com Compo po nent
Err or
Fun ct io nal
Lo gic/B gi c/B lo ck
Prev Prevent entiv iv e
Softw Sof tw are
Theo Theory ry
Servic Serv ic e
Refer Referenc ence e
Not es
Cal i b r at i o n
L o c at i o n s
Co d es
Written by: E. de Schuttelaere
Ch ec k s
D Dii ag r am s
controlled by: J.Aupied
Mai n t en an c e Di ag n o s t i c s 44 of 288
n o t es
formatted by: E. de Schuttelaere
Mat er i al s date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
REV 3
Iontomat Test: Sensitivity
SI.PLX
SM 2305147-100
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Written by: E. de Schuttelaere
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
45 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
REV 3
Iontomat Test: kV Correction
SI.PLX
SM 2305147-100
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Written by: E. de Schuttelaere
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
46 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
REV 3
Iontomat Test: mAs Relais
SI.PLX
SM 2305147-100
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Written by: E. de Schuttelaere
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
47 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
REV 3
MVS DI EUROPE
SI.PLX
SM 2305147-100
Al nment Caig l i bnm r atent ion
Com Compo po Loca t i onent ns
CErr o dor es
Written by: E. de Schuttelaere
Fun Chct ecioknal s
Lo gi ck MPrev Prevent entiv Sof D Digic/B i ac/B g r alo ms ai n t e n aiv n cee DiSoftw ag ntw o sare tics
controlled by: J.Aupied
48 of 288
Theo Theory ry
Servic Serv n o t eicse
formatted by: E. de Schuttelaere
Refer Referenc Mat erence i al se
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
REV 3
MVS DI EUROPE
SI.PLX
SM 2305147-100
Al nment Caig l i bnm r atent ion
Com Compo po Loca t i onent ns
CErr o dor es
Written by: E. de Schuttelaere
Fun Chct ecioknal s
Lo gi ck MPrev Prevent entiv Sof D Digic/B i ac/B g r alo ms ai n t e n aiv n cee DiSoftw ag ntw o sare tics
controlled by: J.Aupied
49 of 288
Theo Theory ry
Servic Serv n o t eicse
formatted by: E. de Schuttelaere
Refer Referenc Mat erence i al se
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
REV 3
MVS DI EUROPE
SI.PLX
SM 2305147-100
Al nment Caig l i bnm r atent ion
Com Compo po Loca t i onent ns
CErr o dor es
Written by: E. de Schuttelaere
Fun Chct ecioknal s
Lo gi ck MPrev Prevent entiv Sof D Digic/B i ac/B g r alo ms ai n t e n aiv n cee DiSoftw ag ntw o sare tics
controlled by: J.Aupied
50 of 288
Theo Theory ry
Servic Serv n o t eicse
formatted by: E. de Schuttelaere
Refer Referenc Mat erence i al se
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
REV 3
MVS DI EUROPE
SI.PLX
SM 2305147-100
Al nment Caig l i bnm r atent ion
Com Compo po Loca t i onent ns
CErr o dor es
Written by: E. de Schuttelaere
Fun Chct ecioknal s
Lo gi ck MPrev Prevent entiv Sof D Digic/B i ac/B g r alo ms ai n t e n aiv n cee DiSoftw ag ntw o sare tics
controlled by: J.Aupied
51 of 288
Theo Theory ry
Servic Serv n o t eicse
formatted by: E. de Schuttelaere
Refer Referenc Mat erence i al se
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
REV 3
Iontomat Test: Sensitivity Drift
SI.PLX
SM 2305147-100
Al nment Caig l i bnm r atent ion
Com Compo po Loca t i onent ns
CErr o dor es
Written by: E. de Schuttelaere
Fun Chct ecioknal s
Lo gi ck MPrev Prevent entiv Sof D Digic/B i ac/B g r alo ms ai n t e n aiv n cee DiSoftw ag ntw o sare tics
controlled by: J.Aupied
52 of 288
Theo Theory ry
Servic Serv n o t eicse
formatted by: E. de Schuttelaere
Refer Referenc Mat erence i al se
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
REV 3
Ionto tomat mat Test: Test: mAs mAs Coun Counter ter Test Test
SI.PLX
SM 2305147-100
Al nment Caig l i bnm r atent ion
Com Compo po Loca t i onent ns
CErr o dor es
Written by: E. de Schuttelaere
Fun Chct ecioknal s
Lo gi ck MPrev Prevent entiv Sof D Digic/B i ac/B g r alo ms ai n t e n aiv n cee DiSoftw ag ntw o sare tics
controlled by: J.Aupied
53 of 288
Theo Theory ry
Servic Serv n o t eicse
formatted by: E. de Schuttelaere
Refer Referenc Mat erence i al se
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
REV 3
MVS DI EUROPE
SI.PLX
SM 2305147-100
Al nment Caig l i bnm r atent ion
Com Compo po Loca t i onent ns
CErr o dor es
Written by: E. de Schuttelaere
Fun Chct ecioknal s
Lo gi ck MPrev Prevent entiv Sof D Digic/B i ac/B g r alo ms ai n t e n aiv n cee DiSoftw ag ntw o sare tics
controlled by: J.Aupied
54 of 288
Theo Theory ry
Servic Serv n o t eicse
formatted by: E. de Schuttelaere
Refer Referenc Mat erence i al se
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
REV 3
Inverter Test
MVS DI EUROPE
SI.PLX
SM 2305147-100
Al nment Caig l i bnm r atent ion
Com Compo po Loca t i onent ns
CErr o dor es
Written by: E. de Schuttelaere
Fun Chct ecioknal s
Lo gi ck MPrev Prevent entiv Sof D Digic/B i ac/B g r alo ms ai n t e n aiv n cee DiSoftw ag ntw o sare tics
controlled by: J.Aupied
55 of 288
Theo Theory ry
Servic Serv n o t eicse
formatted by: E. de Schuttelaere
Refer Referenc Mat erence i al se
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Adjustment Results
Al nment Caig l i bnm r atent ion
Com Compo po Loca t i onent ns
CErr o dor es
Written by: E. de Schuttelaere
Fun Chct ecioknal s
Lo gi ck MPrev Prevent entiv Sof D Digic/B i ac/B g r alo ms ai n t e n aiv n cee DiSoftw ag ntw o sare tics
controlled by: J.Aupied
56 of 288
Theo Theory ry
Servic Serv n o t eicse
formatted by: E. de Schuttelaere
Refer Referenc Mat erence i al se
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
REV 3
Manual Fluoroscopy
SI.PLX
SM 2305147-100
Al nment Caig l i bnm r atent ion
Com Compo po Loca t i onent ns
CErr o dor es
Written by: E. de Schuttelaere
Fun Chct ecioknal s
Lo gi ck MPrev Prevent entiv Sof D Digic/B i ac/B g r alo ms ai n t e n aiv n cee DiSoftw ag ntw o sare tics
controlled by: J.Aupied
57 of 288
Theo Theory ry
Servic Serv n o t eicse
formatted by: E. de Schuttelaere
Refer Referenc Mat erence i al se
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
REV 3
MVS DI EUROPE
SI.PLX
SM 2305147-100
Al nment Caig l i bnm r atent ion
Com Compo po Loca t i onent ns
CErr o dor es
Written by: E. de Schuttelaere
Fun Chct ecioknal s
Lo gi ck MPrev Prevent entiv Sof D Digic/B i ac/B g r alo ms ai n t e n aiv n cee DiSoftw ag ntw o sare tics
controlled by: J.Aupied
58 of 288
Theo Theory ry
Servic Serv n o t eicse
formatted by: E. de Schuttelaere
Refer Referenc Mat erence i al se
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SM 2305147-100
REV 3
Dose Rat Ratee Adju Adjust stme ment nt:: comm common on part part How to use : o
o o o
o
SI.PLX
Following two pages are common to every dose measurement devices. After those pages the document presents: CASE#1 : procedure with SDM cell CASE#2 : procedure with Videomed DI/DIC CASE#3 : procedure with Multiplier CASE#4 with Iontomat :/ procedure KK Interface
Al nment Caig l i bnm r atent ion
Com Compo po Loca t i onent ns
CErr o dor es
Written by: E. de Schuttelaere
Fun Chct ecioknal s
Lo gi ck MPrev Prevent entiv Sof D Digic/B i ac/B g r alo ms ai n t e n aiv n cee DiSoftw ag ntw o sare tics
controlled by: J.Aupied
59 of 288
Theo Theory ry
Servic Serv n o t eicse
formatted by: E. de Schuttelaere
Refer Referenc Mat erence i al se
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
REV 3
MVS DI EUROPE
SI.PLX
SM 2305147-100
Al ig nm nment ent Calibration
Component Locations
Error Codes
Written by: E. de Schuttelaere
Functional Checks
Logic/Block Preventive Software Diagrams Maintenance Diagnostics
controlled by: J.Aupied
60 of 288
Theory
Service notes
formatted by: E. de Schuttelaere
Reference Materials
Notes
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
REV 3
DOSE ADJUST case#1 : SDM cell
SI.PLX
SM 2305147-100
Al nment Caig l i bnm r atent ion
Com Compo po Loca t i onent ns
CErr o dor es
Written by: E. de Schuttelaere
Fun Chct ecioknal s
Lo gi ck MPrev Prevent entiv Sof D Digic/B i ac/B g r alo ms ai n t e n aiv n cee DiSoftw ag ntw o sare tics
controlled by: J.Aupied
61 of 288
Theo Theory ry
Servic Serv n o t eicse
formatted by: E. de Schuttelaere
Refer Referenc Mat erence i al se
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
REV 3
MVS DI EUROPE
SI.PLX
SM 2305147-100
Al nment Caig l i bnm r atent ion
Com Compo po Loca t i onent ns
CErr o dor es
Written by: E. de Schuttelaere
Fun Chct ecioknal s
Lo gi ck MPrev Prevent entiv Sof D Digic/B i ac/B g r alo ms ai n t e n aiv n cee DiSoftw ag ntw o sare tics
controlled by: J.Aupied
62 of 288
Theo Theory ry
Servic Serv n o t eicse
formatted by: E. de Schuttelaere
Refer Referenc Mat erence i al se
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
REV 3
MVS DI EUROPE
SI.PLX
SM 2305147-100
Al nment Caig l i bnm r atent ion
Com Compo po Loca t i onent ns
CErr o dor es
Written by: E. de Schuttelaere
Fun Chct ecioknal s
Lo gi ck MPrev Prevent entiv Sof D Digic/B i ac/B g r alo ms ai n t e n aiv n cee DiSoftw ag ntw o sare tics
controlled by: J.Aupied
63 of 288
Theo Theory ry
Servic Serv n o t eicse
formatted by: E. de Schuttelaere
Refer Referenc Mat erence i al se
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
REV 3
MVS DI EUROPE
SI.PLX
SM 2305147-100
Al nment Caig l i bnm r atent ion
Com Compo po Loca t i onent ns
CErr o dor es
Written by: E. de Schuttelaere
Fun Chct ecioknal s
Lo gi ck MPrev Prevent entiv Sof D Digic/B i ac/B g r alo ms ai n t e n aiv n cee DiSoftw ag ntw o sare tics
controlled by: J.Aupied
64 of 288
Theo Theory ry
Servic Serv n o t eicse
formatted by: E. de Schuttelaere
Refer Referenc Mat erence i al se
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
REV 3
MVS DI EUROPE
SI.PLX
SM 2305147-100
Al nment Caig l i bnm r atent ion
Com Compo po Loca t i onent ns
CErr o dor es
Written by: E. de Schuttelaere
Fun Chct ecioknal s
Lo gi ck MPrev Prevent entiv Sof D Digic/B i ac/B g r alo ms ai n t e n aiv n cee DiSoftw ag ntw o sare tics
controlled by: J.Aupied
65 of 288
Theo Theory ry
Servic Serv n o t eicse
formatted by: E. de Schuttelaere
Refer Referenc Mat erence i al se
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
REV 3
MVS DI EUROPE
SI.PLX
SM 2305147-100
Al ig nm nment ent Calibration
Component Locations
Error Codes
Written by: E. de Schuttelaere
Functional Checks
Logic/Block Preventive Software Diagrams Maintenance Diagnostics
controlled by: J.Aupied
66 of 288
Theory
Service notes
formatted by: E. de Schuttelaere
Reference Materials
Notes
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
DOSE ADJUST case#2 : Videomed DI/DIC
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Written by: E. de Schuttelaere
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
67 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
REV 3
MVS DI EUROPE
SI.PLX
SM 2305147-100
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Written by: E. de Schuttelaere
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
68 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
REV 3
MVS DI EUROPE
SI.PLX
SM 2305147-100
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Written by: E. de Schuttelaere
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
69 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
REV 3
MVS DI EUROPE
SI.PLX
SM 2305147-100
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Written by: E. de Schuttelaere
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
70 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
REV 3
MVS DI EUROPE
SI.PLX
SM 2305147-100
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Written by: E. de Schuttelaere
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
71 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
REV 3
MVS DI EUROPE
SI.PLX
SM 2305147-100
Al ig nm nment ent Calibration
Component Locations
Error Codes
Written by: E. de Schuttelaere
Functional Checks
Logic/Block Preventive Software Diagrams Maintenance Diagnostics
controlled by: J.Aupied
72 of 288
Theory
Service notes
formatted by: E. de Schuttelaere
Reference Materials
Notes
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
REV 3
DOSE ADJUST case#3 : Multiplier
SI.PLX
SM 2305147-100
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Written by: E. de Schuttelaere
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
73 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
REV 3
MVS DI EUROPE
SI.PLX
SM 2305147-100
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Written by: E. de Schuttelaere
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
74 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
REV 3
MVS DI EUROPE
SI.PLX
SM 2305147-100
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Written by: E. de Schuttelaere
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
75 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
REV 3
MVS DI EUROPE
SI.PLX
SM 2305147-100
Al ig nm nment ent Calibration
Component Locations
Error Codes
Written by: E. de Schuttelaere
Functional Checks
Logic/Block Preventive Software Diagrams Maintenance Diagnostics
controlled by: J.Aupied
76 of 288
Theory
Service notes
formatted by: E. de Schuttelaere
Reference Materials
Notes
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
REV 3
DOSE ADJUST case#4 : Iontomat with KK Interface
SI.PLX
SM 2305147-100
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Written by: E. de Schuttelaere
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
77 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
REV 3
MVS DI EUROPE
SI.PLX
SM 2305147-100
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Written by: E. de Schuttelaere
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
78 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
REV 3
MVS DI EUROPE
SI.PLX
SM 2305147-100
Al ig nm nment ent Calibration
Component Locations
Error Codes
Functional Checks
Written by: E. de Schuttelaere
Logic/Block Preventive Software Diagrams Maintenance Diagnostics
controlled by: J.Aupied
79 of 288
Theory
Service notes
Reference Materials
formatted by: E. de Schuttelaere
Notes
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
#5 Other job cards (not frequently used) with OEM software
Option selection
-
Configuration Configuratio n : Site Structure : Option Selection Polydoros LX
1
option group selection
Configuration : Site Structure : Option Selection Polydoros LX
3
option group selection OK
maximum power mawimum power continuous fluoroscopy
-
OK
mawimum power continuous fluoroscopy
5
2
4
option selection
option selection
50 KW
available
this window appears in each case after selection of the option: confirm with OK THIS IS A SIEMENS SOFTWARE OPTION PROPERTY. A CHOSE CAN BE PERFORM BETWEEN 30KW AND 50 KW. THE CUSTUMER MUST HAVE PAYED FOR THAT TO SIEMENS
REGARDING THE TUBE ON SITE, MAX FLURO POWER CAN BE INCREASE
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Written by: E. de Schuttelaere
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
80 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Site structure
-
System
XCS Service Application - Main Program Configuration
Data
Components
Adjustment
Diagnostic
Info
help.
site structure organprogram
-
Site Configuration
!
there is no configuration information stored in the XCU or configuration data are damaged. do you want to configurate a new site ? remark: if you have an existing site data floppy, chose cancel and restore site data to XCU 1
OK
DELETE
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Written by: E. de Schuttelaere
Err or Co d es
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
81 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
-
Site Configuration
?
do you want to store the actual site configuration data in the XCU and the data floppy ?
Site Configuration error
!
drive A : not ready please insert your site data floppy and try again
OK
21
OK
-
DELETE
DELETE
only if there is no floppy in your PC
A message is output only i f no Backup disk is inserted in the disk drive ‘A’ Insert the Backup disk
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Written by: E. de Schuttelaere
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
84 of 288
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
formatted by: E. de Schuttelaere
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
-
-
Site Configuration warning
!
station in XCU and in floppy can not be check cause: station ID is not accessible on floppy
Congratulation
!
data were successifully stored on site data floppy and XCU 22
OK
DELETE OK
wrong ID N° on the backup disk
A message is output only if no ID number has been input or a wrong one has been input Exists on the Backup disk Continue with OK
select “ DATA” “PRIV.POLYDOR “PRIV.POLYDOROS OS LX” display on D100 indicates ( 2 or 3 ) ( only if the led display see next page for data option.
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Written by: E. de Schuttelaere
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
85 of 288
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
formatted by: E. de Schuttelaere
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Data options
-
System
Configuration
Data
XCS Service Application - Main Program Components Components
Adjustment
Diagnostic Diagnostic
Info
Help
.
download to unit restore from disk rest.old from disk
The selection between 50 KW KW and 30 KW KW is a
backup to disk erase EEprom priv.polydoros LX 50 KW 30 KW
Siemens software option. Don’t change that option
DESK
D100
D 2 0 0
D220
POLYDOROS LX
XCS connection
site configuration
NUM: logged on
Group:O
.
Al ig nm nment ent Calibration
Component Locations
Error Codes
Functional Checks
Written by: E. de Schuttelaere
Logic/Block Preventive Software Diagrams Maintenance Diagnostics
controlled by: J.Aupied
86 of 288
Theory
Service notes
formatted by: E. de Schuttelaere
Reference Materials
Notes
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
-
XCS Service Application
?
this will overwrite theyour adjustment data ofshould the generator if you have already adjust generator, you not load data
do you want to continue ?
yes
no
To be done if on board D100 the indication displayed is “ 2 or 3 “ Insert Backup floppy in drive A A
-
Private iniblocks for 50KW generator
3 block transmitted
OK
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Written by: E. de Schuttelaere
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
87 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Download software to unit
-
XCS Service Application - Main Program
System
Configuration
Data Data
Components
Adjustment
Diagnostic
Info
Help
.
download to unit restore from disk restore from old disk backup to disk erase EEprom PR.Polydoros LX
Component
If a PC is operated without power pack, only with accumulator power supply, ensure that the accumulator is fully charged.
Data: Download Select Component Version
Vers on FI
status
HEATING XCU
Print
For the generator, download for XCU D200 and filament D220 has already been performed ar the factory. Therefore: perform the XCU downloan only if: 1. software 2. after after changing replacing the D200 3. erform the filamen filamentt download download onl if led on D220 is
OK
Deselect Update
Cancel XCU
Prior to a filament download, the system configuration must be performed. For heating download, select HEATING and press OK. OK.
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Written by: E. de Schuttelaere
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
88 of 288
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
formatted by: E. de Schuttelaere
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
-
-
Component:
XCU
File name:
VAD2J_CX.HEX
Data: Download Select Component
Component
Version
Vers on FI
Data : Download Start Cancel
status
446602 Byte
HEATING XCU
OK Print
-
XCU : rom.dll
?
-
Deselect
Download may overwrite existing configuration and adjusted data. Do you want to backup these data before starting download ?
!
Cancel YES
Erase Flash PROM
Update
NO
Before the download will start, the flash PROM of the selected component is erased. The erase procedure may take up to 5 minutes. please hold on.
XCU
-
If you press YES: you want to store a copy of the XCU configuration on floppy disk. If you press NO : no backup is wanted
-
Data : Download
Component:
XCU
File name:
VAD2J_CX.HEX
Start Cancel
Data: open 446602 Byte
25 %
OK
Data name VA02J-CX.hex disk or drive
Cancel
VA02J-CX.hex
On board D100:
a:\
1. XCU-download = 1 ( on only ly for first d download, ownload, otherwise “ b “ ) 2. filament download = F
Data format: Hex Files ( ?????_ex.hex )
Checksum
disk or drive a:
The system is now computing the checksum of the downloaded code. please stand by for approximaly 1 minute.
Filament-download “ V…._IX.hex “ must be selected during the XCU download. For XCU file names: call: “ V…._CX.hex “ “
!
A system reset reset may be performed afte afterr the checksum has been completed.
Al ig nm nment ent Calibration
Component Locations
Error Codes
Functional Checks
Written by: E. de Schuttelaere
Logic/Block Preventive Software Diagrams Maintenance Diagnostics
controlled by: J.Aupied
89 of 288
Theory
Service notes
formatted by: E. de Schuttelaere
Reference Materials
Notes
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
-
In the main program, select SYSTEM / QUIT > exit the “ System LOG off “ window will answerd “ put to unit “ generator OFF / ON
Reset the station is now reseted to run the new download files. This will take about 2 minutes. Please hold on.
If D200 dot will not start logging again, turn off / on the system. 5%
-
Warning : deleting EE prom also deletes the organ programs. Ensure that “ struc.dat “ on the disk corresponds to the latest staus of the system. If necessary, necessary, update update “ struct.data “ with backup or write down all “ KV/MAS/…organ program names “ data and enter it following the copied configuration in the organ program menu. menu.
X C U com.DLL
!
Download successfully completed. please switch off the generator
-
OK
Component
Data: Download Select Component Version
Vers on FI
status
HEATING XCU
-
System : Logoff
Start of service : 13 : 15 : 56 End of service : 13 : 29 : 16
OK Print
put to unit
Deselect
Cancel
Update
User : link
Cancel download OK
XCU
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Written by: E. de Schuttelaere
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
90 of 288
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
formatted by: E. de Schuttelaere
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Erase EE prom
-
XCS Service Application - Main Program
System
Configuratio Configuration n
Data Data
Components
Adjustment
Diagnostic
Info
Help
.
download to unit restore from disk restore from old disk backup to disk erase EEprom PR.P PR.Pol olyd ydor oros os LX
The led display on D100 must change from “b” to “1” when “yes” is clicked on. Led display on D22 0Oat 0%…approx.10. When “erasing” has been terminated, the led display on D100 reads “2”
-
Erase EE PROM Cancel active, if no communication between XCU and PC exists. Working on: enter text, than put to unit “restore performed” is displayed
All configuration and adjustment data will be lost. Do you really want to continue ??? III Check status on D22. III III The erasing of the EE PROM is going well when 20 is shown III III after the dot is toggling again III
No
Yes
-
-
System : Logoff
Start of service : 13 : 15 : 56 End of service : 13 : 29 : 16
put to unit
!
Cancel
User : Jack
Working on:
X C U Service Application All adjusting and configurating configurating data is lost. Before carry on servicing. turn off the station and then logon again using CONNECT of the SYSTEM menu.
OK
Delete EE PROM
Al ig nm nment ent Calibration
Component Locations
Error Codes
Functional Checks
Written by: E. de Schuttelaere
Logic/Block Preventive Software Diagrams Maintenance Diagnostics
controlled by: J.Aupied
91 of 288
Theory
Service notes
Reference Materials
formatted by: E. de Schuttelaere
Notes
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Components adjustment (Re-Routing to other sub-systems than XCU)
-
System
XCS Service Application - Main Program Configuration
Data
Components
Adjustment
Diagnostic
Info
Help
.
Polydoros LX
DESK
INSERT JUMPER X44 ON D100 FOR ADJUSTMENT
D100
Always perform a backup after any adjustment
D 2 0 0
D220
POLYDOROS LX
XCS connection
site configuration
NUM: logged on
Group:O
.
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Written by: E. de Schuttelaere
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
92 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Skin dose rate adjustment
-
skin doserate V tube : 110 KV A24
tube current
3.9
fluoroscopy
A23
ma
change ma until desired dose is displayed on the dosimeter instrument 261 nGµ / s without grid or 411nGµ / s with grid
ON OFF
Cancel
A25 OK
CHANGE MA UNTIL DESIRED SKIN DOSE IS DISPLAYED ON THE DOSEMETER INSTRUMENT. After reaching reac hing the specified dose by reducing the tube current and storing this setting, the tube current cannot be increased again in that mode. In order to set the skin dose again, “Configuration “ must be selected and stored again. AFTER TERMINATION OF THE PL LX ADJUSTMENT, LEAVE ADJUSTMENT PROGRAM VIA “ Components – XCS System – Service “ . SELECT SYSTEM / QUIT IN THE MAIN PROGRAM > LEAVE WINDOW.
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Written by: E. de Schuttelaere
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
93 of 288
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
formatted by: E. de Schuttelaere
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Customer data data
-
System
XCS Service Application - Main Program Configuration
Data
Components
Adjustment
Diagnostic
Info
help.
sw/w version customer data system data technical data service data operating time
-
Info : Customer Data
customer specific information get from unit Customer Name:
DR.Read
Adresse :
8 avenue Leonard de Vinci
City :
Bordeaux
Zip Code :
33807
put to unit
print
Country : France Phone N° : 0557891017
Customer N° :
12345679 Modem N° : 0557891029
unit specific information
print to file
cancel
BZ N° :
33807
Reference N°:
service Ctrl N° :
33807
Handover Date : 05.06.01
unit serial N° :
33807
33807
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Written by: E. de Schuttelaere
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
94 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
System data
-
System
XCS Service Application - Main Program Configuration
Data
Components
Adjustment
Diagnostic
Info
help.
sw/w version customer data system data technical data service data operating time
-
XCS Service Application - Main Program
System
Configuration
Data
Components
Adjustment
Diagnostic
Info
Help
.
Polydoros LX
-
DESK
Info : System Data
Component Name
Part N° D100
-
DESK PLX KK UT FLURO UNIT KK EXPOSURE UNIT 1
11 75 640 X3
Edit System Data
D220
OK POLYDOROS LX
Component Name: Desk PLX Part N°:
11 75 640 x3
Serial N°:
1005
cancel XCS connection product 02 status
Wiring A index
site configuration
D 2 0 0
NUM: logged on
Group:O
.
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Written by: E. de Schuttelaere
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
95 of 288
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
formatted by: E. de Schuttelaere
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Technical data
-
System
XCS Service Application - Main Program Configuration
Data
Components
Adjustment
Diagnostic
Info
help.
sw/w version customer data system data technical data service data operating time
-
Info : Technical Data speed info N° 16 / 99
title PLLX SOFTWARE VA00A / VA00B
get from unit put to unit new entry edit Delete print print to file cancel
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Written by: E. de Schuttelaere
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e D Dii ag r am s Mai n t en an c e
controlled by: J.Aupied
Softw Sof tw are Di ag n o s t i c s
96 of 288
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
formatted by: E. de Schuttelaere
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Service data data
-
System
XCS Service Application - Main Program Configuration
Data
Components
Adjustment
Diagnostic
Info
help.
sw/w version customer data system data technical data service data operating time
-
Info : Service Data date 02.08.99 25.06.01
start time 12.55.12 14.25.23
end time
user
12.59.54 16.25.45
sdt jhgy
group 0 I
get from unit print print to file cancel
Working on:
Delete E EE E prom I
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Written by: E. de Schuttelaere
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
97 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
#6 Complementa Complementary ry Information Adjustment of Tube #1 or #2 In this dialog, a table indicates information about PREHEATING, FILAMENT CORRECTION and CURRENT of the tube selected. The adjustment is executed with the aid of PT: 510:Emulation. o Module: Preheating o Module: Filament Correction o Module: Current
Focus: Focus is the fluoroscopy focus Preheating IH: Preheating current Filament Correction KV tube voltage with which adjustment was done IROE1 lower tube current with which adjustment was done IH1 heating current learned f or kV and IROE1 IROE2 upper tube current with which adjustment was done IH2 heating current learned for kV and IROE2 MUL Multiplication factor: IH from Emission table will be multiplied with this value / 1000 ADD Additional value: to IH from Emission table this value will be added IH nominal = IH Table * MUL/1000 + ADD;
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Written by: E. de Schuttelaere
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
98 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Current KV tub tubee voltag voltagee with whi which ch adj adjust ustmen mentt was don donee IROE1 lower tube current with which adjustment was done IROE2 upper tube current with which adjustment was done MUL Multiplication factor: IH nominal will be multiplied with this value / 1000 ADD Addition IH nominal will be multiplied with this value. IH = IH nominal * MUL/1000 + ADD; Remark: The values MUL and ADD are calculated out of the PT emulation values PF1 and PF2 and for that not identical! You can look at the Emission tables as well as all t h e o t h e r t u b e d a t a Dose Rate Adjustment The adjustment of the dose rate according to procedure and appearance depends on the detector used. Multiplier: Learning the voltages for area 1 (fluoroscopy) and area 2 (exposure) Display: Voltage of area 1 and voltage of area 2 B signal: Learning the nominal value (voltage) Display: Nominal value PDA: Learning the intensification over all zoom formats and measurement field combinations Display: PDA data with sub dialog for each zoom degree. Skin Dose Rate Adjustment This adjustment dialog is intended for learning the skin dose lim itation 10 R/min at the vertexes 110 kV and 70 kV as well as for learning the minimum SID. Reduced DIGITAL RADIOGRAPHY auto/HIGH CONTRAT (3BP): CONTRAT: FLUOROSCOPY must be limited to 20 R/min. Active marking: 5 R/min, not active: 10 R/min. Reduced DIGITAL RADIOGRAPHY kV manual: The skin dose for kV manual operation must be limited to 5 R/min.
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Written by: E. de Schuttelaere
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
99 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
TV Iris Adjustment Fluoroscopy unit. The Mirror correction must be filled in before the adjustment. If it is active recommended standard setting, the position is determined wit h and without gray filter or mirror. The generator assumes that both values have been learned at least once. The position with gray filter/mirror is used for indirect exposures. The position without gray filter/m irror is used for fluoroscopy, but also for exposures where the opening with gray f ilter/mirror is not sufficient. Radiography unit In the Iris for radiography determine, whether the iris is opened to a specific value for direct exposures or whether it should be closed. Poly BV Adaptation: Adaptation: Parallel to the setting of the Poly BV adaptation in the configuration, the value can also be learned more easily in normal operation with this adjustment. If the generator is in the service mode, this is indicated and adjustment refused. Tests: General Test 70
Firing pulse (large oscillating circuit)
D240
Test 71
Firing pulse (small oscillating circuit)
D240
Test 72
Oscillating circuit switchover
D240
Test 75
Maximum frequency
D240
Test 90
Variable iris position
D270
Test 91
Open iris
D270
Test 92
Close iris
D270
Test 93
Open and close iris
D270
Test 95
Mirror position
D270
Test 97
Multiplier voltage
D270
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Written by: E. de Schuttelaere
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
100 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Tests: Open Iris Iris is alwa alway ys o op pen and IIri riss iiss ttre reat ated ed nor orm mal ally ly.. selection ion always open offers offers the option option of keepi keeping ng the TV iris fully fully open open aatt al alll ti times mes wit withou houtt interv interveention in its power supply so that The select measurements regarding the B signal reserve can be carried out. The sele electio tion reflects the current ent statu tuss in the generato ratorr. Tests: Disable LOCAL NETWORK (RAS) Error If the generator recognizes errors in the communication with its LOCAL NETWORK (RAS) board, it usually transmits the error 665, which must be acknowledged. In order to operate the generator even without a conn ected LOCAL NETWORK (RAS) unit, e.g. via the service field D211, error generation can be prevented. With YES, the generator is reset by the software and restarted with the error suppressed. With NO”, the status is retained. In order to reactivate the reaction to the error, the generator must be reset via switch off and switch on, or via the reset on D210. Tests: Iontomat Drift Prepares the Iontomat for the drift measurement under radiation. Additionally, the jumper D901.BR8 must be removed. Monitoring Tube Load The tr trace is suitable fo for m mo onitoring tth he ac activity o off th the tu tube lo load cco omputer. The meaning of the dialog elements is described in the section Monitoring. There are two types of entries in the Trace dynamic data list and static data. Index Serial number of entry %HU Heat units: current amount of heat in % of Q max %At 80%, the 100% at the control console are disabled Wait/min waiting time, also displayed at the control console Q act/kJ Current amount of heat in kJ (coarse resolution) Q act/J Current amount of heat in J (fine resolution)
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Written by: E. de Schuttelaere
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
101 of 288
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
formatted by: E. de Schuttelaere
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Tube o o o
Selected tube (1 or 2) Q max/kJ Maximum permissible heat content of the tube in kJ; exceeding this value causes a 'Heavy overload' Q wbl/kJ Heat reference power in kJ; exceeding this value causes display of a waiting time Q rbl/kJ Tube reference power in kJ; exceeding this value causes the 100% to be disabled
Monitoring Iris The trace is suitable for monitoring the TV iris position and the mirror or gray filter position with SIRCAM operation or DIGITAL RADIOGRAPHY operation. Entries take place only if FLUOROSCOPYON is active or ZB ON is active. Each entry in the Trace consists of several elements: Ind. Serial number of the entry EXP Exposure Y: yes N: no Pos Position (not opening) of the iris diaphragm Open Iris is always opens (Y/N) Mirr Mirror/gray filter retracted (Y/N) D/P Dose per image; pre-set by image system justment TV iris as 'value without mirror' and 'value with MIR Mirror correction: dependent on mirror Y/ N: a value that was learned in Ad mirror'. IRK Iris diaphragm correction; pre-set by image system depending on technical aspects MAN override; 'density' correction viaMAN; generator control console EP [1/4]ManualResult from D/P + MIR + IRK: this value yields the position of the iris diaphragm after transformation via a generator internal table. The individual parameters are effective only with exposure.
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Written by: E. de Schuttelaere
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
102 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Monitoring FLUOROSCOPY Tester The FLUOROSCOPY watcher monitors the fluoroscopy. f luoroscopy. The dose rate control has no supply, if at the start of the dialog kV manual manual or Control stop is selected / a message is displayed that the curve address cannot be read. Indicates the discreet values of the fluoroscopy; it is updated approx. every 0.3 seconds with the contents nominal kV, nominal mA, actual time, Diamentor output and water value. KV/mA Indicates the current curve on which the generator controls? Selection of the automatic degree as well as switchover between normal and HIGH CONTRAT fluoroscopy and SID tracking are immediately taken into account as well. The curve is calculated from The original curve The max. FLUOROSCOPY output The skin dose limitation As of May 1, 95, the following values apply: 5 R/min for manual kV, 10 R/min for Normal FL, 20 R/min. for HIGH CONTRAT CONTRAT FL. The straight line 10 R/min is learned in the adjustment with the vertexes 110 kV and 70 kV. The SID straight trackinglines 5 R/min and 20 R/min are calculated by subtraction / addition of 3 EP or halving / doubling of the FLUOROSCOPY current. The curve including the skin dose limitation is moved to the right with increasing SID. With SID standard it is in its original position (left). The current values of all points are calculated as follows: MA act = (mA norm) * (SID act: MEASURING POINT IMAGE DISTANCE) 2 / (SID norm: MEASURING POINT IMAGE DISTANCE) 2 Show Error List For each error a description as well as possible causes and remedies are indicated. The error list can also be selected directly by double clicking the file ... \INFO\ERR_ENG.HLP.
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Written by: E. de Schuttelaere
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
103 of 288
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
formatted by: E. de Schuttelaere
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
LX 30/50/lite only S44 switch for programming
Master board: D100
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Written by: E. de Schuttelaere
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
104 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
LX 30/50/lite only inverter board: D110 Starter board: D115
Filament board: MAS oint
H1
Al ig nm nment ent Calibration
Component Locations
Error Codes
Written by: E. de Schuttelaere
Functional Checks
Logic/Block Preventive Software Diagrams Maintenance Diagnostics
controlled by: J.Aupied
105 of 288
Theory
Service notes
formatted by: E. de Schuttelaere
Reference Materials
Notes
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
HT transformer: H1
T2
M16
LX 30/50/lite only
Al ig nm nment ent Calibration
Component Locations
Error Codes
Written by: E. de Schuttelaere
Functional Checks
Logic/Block Preventive Software Diagrams Maintenance Diagnostics
controlled by: J.Aupied
106 of 288
Theory
Service notes
Reference Materials
formatted by: E. de Schuttelaere
Notes
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
LX 30/50/lite only
KK interface panel: D200
PC connection
Switching circuit: D160
Power ON power ON OFF
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Written by: E. de Schuttelaere
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
107 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Part 1 : ERRORS DISPLAY Status displays on the 7 segments indicator D100 0
Initialization
1
Initialization executed, wait for XCS
2
Power line connection with XCU
3
Wait for INIT data
4
INIT data received, wait for tube assembly
5
Tube assembly selection
b
Fluoroscopy / radiography enable
h
ZB ( exposure preparation ) ON
r
Radiation enable, boosting ( anode and filament ) ok
A
Exposure ON
d
Fluoroscopy ON
*
Flashing decimal point ( DP) shows dummy telegrams from XCS
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Written by: E. de Schuttelaere
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
108 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
LX 30/50/lite only HOW to TROUBLE SHOOT LX35/50/Lite BOOT To test with a minimum start configuration: -> disconnect all ribbon cables from D100 and key board then power up in following configurations: o
o o o o
31 on on D200 and number t 1 on D100 D200 + D160 : D160 : error 31 Explanation: “31” means “31” means : ARCNET error (no partner detected) ; the ARCNET controller does not detect an ARCNET signal on wires. Either ARCNET has a short circuit or is not connected. In such situation check all XCS cables and connectors for short cut or open connection. on D200 and number number 1 on D100 D200 + D160 + key board : board : 00 00 on “1” means means that system is waiting for XCU ready. Explanation: “00” means “00” means that all the system is running and “1” D200 + D160 + key board + D100: D100: error 604 on 604 on key board and number 4 on D100 on key board and number 4 on D100 119 on D200 + D160 + key board + D100 + inverter : inverter : error 119 Explanation: “4” “4” means means that initialization is fished. on key board Auxiliary loop open = open = error 003 003 on
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Written by: E. de Schuttelaere
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
109 of 288
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
formatted by: E. de Schuttelaere
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
LX 30/50 /lite only
Case #1 : HCS (hardware communicatio communication n system) network operation has not started.
- Generator “OFF” “OFF” - Remove D100.X41 and insert dummy plug “ solder a resistor of 120ohm between 1 and 6 in the serial plug (type: mind pin 09 plug). plug). This plug is part of the accessories
“1” is displayed on the 7 segments of board D100 (generator is waiting for an XCU target ready)
Generator “ON” “ON”
Link to : Hardware Details
7 segments display on board D100 shows “B” “B” (generator is ready)
7 segments display on board D100 shows “1.” “1.” (generator is waiting for an XCU target ready)
-> Defective console or console connection between D100 plug: X48 in the console X9.X41 on D160
- Generator “OFF” “OFF” - Remove plug D200.X4 and insert plug X41 (feed line D160 ) on D200.X4
- Generator “ON” “ON” - Display on D100 read “1“ “1“
Link to : Signal Check (2 pages later)
If there is error 007 APID 007 APID 80 appears on the console - Set back the error message with the exposure switch - Default data 73kv, 20mas, large focus 80kw are displayed on the console - KV , mas selection is impossible
-> Board D100 is defective
If there are only two oblique strips in the left corner on the console, and the console does not initialise
-> Board D200 is defective - After exchange of board D200, perform download
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Written by: E. de Schuttelaere
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
110 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Case #2 : If several network n etwork subscribes are connected to the network “ Videomed DI ; Sireskop CX” 1. Remove the plug D20 D200.X3 0.X3 and insert the d dummy ummy plu plug g 2. Generator ON
If 7 segments display on D100 remains on “1” “1” -> error in the generator
A (link)
7 segments display on D100 remains on “1” (waiting XCU target ready) -> error in DI. Replace board D5 or cable break between DI and XCU (D200)
7 segments display on D100 remains on “1” (waiting XCU target ready) -> error in the basic unit. Replace board D3 or cable break between
Link to : Signal Check (next page)
If 7 segments display on D100 show “B” (generator is ready) - Generator “OFF” “OFF”
-> error in the peripherals
-- Remove dummy from D200.X3 Plug the the XCS cable plug ( Videomed DI feed line ) on D200.X3 - Remove the XCS cable ( feed line to the unit ) in Videomed DI D5.X12 D5.X12 , plug X20 jumper on the D5 board in Videomed DI. - Generator “ON” “ON”
7 segment display on D100 show s how “B“ (generator is ready) -> error in the unit “B“(generator Generator “OFF” “OFF” Remove plug X19 on D3 (2 kinds) in the basic unit and plug the jumper JP1 on this board Insert the XCS cable ( feed line to the Sireskop CX ) D5.X12 in Videomed DI , remove jumper X20 on the board D5 (2 kinds of board) Generator “ON” “ON”
7 segments display on D100 show “B” (generator is ready) -> error in the spot-film device or cable brake between basic unit and spot-film device
Insert jumper JP1 on D3 and the plug X19
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Written by: E. de Schuttelaere
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
111 of 288
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
formatted by: E. de Schuttelaere
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
SIGNAL CHECK Checking DI pulses in the XCS network measuring points points D200.X D200.X4-1 4-1 and 6
Link back to : CASE#1
200ns
200ns
7-15v
7-15v
Uss max 2v
Uss max 2v
over shoot
400ns
Diagram N° 1 = normal
400ns
Diagram N° 2 = over-shoot
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Written by: E. de Schuttelaere
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
112 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Part 3 : LX30/50/lite ERRORS LIST
LX 30/50/lite only
CONSOLE Error 001: Console Processor defective (internal timer of the 80C535) The processor system of display field D230 tests the internal timer of processor 80C535. If the timer is defective, error 001 is displayed. Check: Replace control console Error 002: Console External RAM error During initialization the processor system of display field D230 tests the external RAM. If the external RAM is defective, error 2 is displayed. Check Replace control console Error 101: 101: Console timeout Error 102: 102: No acknowledge when transmitting to the console. Error 103: 103: No acknowledge when receiving from the console. Error 104: 104: Buffer overflow when receiving from the console. Error 105: 105: Incorrect response from the console. Error 106: 106: Console software not loaded Console D230 and host D210 communicates via the serial interface and interface controller D211. If the console cannot be addressed during initialization, the generator is booted without the con sole. If communication between D211 and D230 is interrupted after the console is initialized, triggere d by D211, depending on the error 101 is triggered by D211.In case of communication errors between D2 11 and D230, error 102...105 is triggered type of error. Check: Visually inspects 4 wires cable for free passage/short circuits; replace if defective. D230, D211 is defective and must be replaced. Tube arcing. Inspect cable routing of D211/D209/D200/D230 and protective conductor. Is the firmware properly loaded? : Adhere to the overview in the generator circuit diagram for lamps and LED’s in the power cabinet.
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Written by: E. de Schuttelaere
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
113 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Miscellaneous Here are mentioned errors whose can’t be classified by an error number, but can be recorded by wrong sequence of events or irregular console display. Console shows only Initialization message Unit missing Fluoroscopy display missing No exposure release Console shows only Initialization message : (RAS) S) system and LED D211.LOCK D211.LOCK off and LED D2 D211.GEN_OK 11.GEN_OK off, then the generator is waiting Check in case of a LOCAL NETWORK (RA (RAS) S) data : Error within LOCAL NETWORK (RAS) loop or in Unit / DIGITAL RADIOGRAPHY RADIOGRAPHY system: if f or LOCAL NETWORK (RA D210.LED 7 V5 (lowest left) rem ains active. FLASH memory D210 is defective or empty: “Start Download” Unit missing : A unit isn’t displayed at the console No unit configured for the unit : Configuration / Unit selection X (1...5) : configure a unit: A tube is configured for the unit which is no nott yet adjusted : do Adjustment / Tube1 or Tube 2 Fluoroscopy display missing : The fluoro field atunit the programmed. console is empty Check No scopy fluoroscopy Program fluoroscopy (only possible for Unit 1, but for all unit s): Missing fluoroscopy adjustments (dose rate, skin d ose, TV, Iris). Do Adjustment / Dose rate or Skin dose or Iris. Iontomat is defective (even Iontomat field is empty) Diagnostics / Tests / Communication shows Iontomat communication state.
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Written by: E. de Schuttelaere
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
114 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
No exposure release : The exposure is started but there is no release of ra diation and no error message. Check exposure control signals missing (exposure LED’s D211): the hardware safety circuit is not activated (Signal EXT_HW / yellow L LE ED D211) Radiation is blocked by a component (at least with signal AR On coming coming the green SINV LED’s on D220, D240, D270 and D211 must be active): the pins D291.X90...X94 (depending on KK unit) are not connected the signals AR and EXT_HW won't be activated. There is a waiting time displayed at the console caused by the tube load calculator and the option 'exposure blocked with waiting time' is enabled the exposure data are blinking the Limit function is active.
FILAMENT ERRORS Error number 119 Filament circuit timeout : the communication between filament board D220 and master board D100 is defective. The possible error causes are: o Serial interface interrupted o D100 or D220 defective o Arcing tube o Defective cable o Defective protective ground wire o Defective software “ when r eloaded “ o Check +5v +/- 0.2v on board D100 and D160 and D220 o The error must be disregarded if the led on D220 flashes and if no firmware has been loaded: perform download Error num ber 120 NAK during transmission to the filament circuit. The possible error causes are: o o o o
Serial interface interrupted D100 or D220 defective Arcing tube Defective cable
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Written by: E. de Schuttelaere
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
115 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
o o o o
Defective protective ground wire Defective software “ when reloaded “ Check +5v +/- 0.2v on boar d D100 and D160 and D220 The error must be disregarded if the led on D220 flashes and if no firmware has been loaded: perform download
Error num ber 121 NAK during reception from the filament circuit. The possible error causes are: o Serial interface interrupted o D100 or D220 defective o Arcing tube o Def ective cable o Defective protective ground wire o Defective software “ when reloaded “ o Check +5v +/- 0.2v on board D100 and D160 and D220 o The error must be disregarded if the led on D220 flashes and if no fir mware has been loaded: perform download Error number 122 Buffer overflow during reception from the filament circuit. The possible error causes are: o
o
Serial interface interrupted D100 or D220 defective Arcing tube Defective cable Defective protective ground wire Defective software “ when reloaded “ Check +5v +/- 0.2v on board D100 and D160 and D220
o
The error must be disregarded if the led on D220 flashes and if no fir mware has been loaded: perform download
o o o o o
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Written by: E. de Schuttelaere
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
116 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Error number 123 Incorrect response from the filament circuit. The possible error causes are: o Serial interface interrupted o D100 or D220 defective o Arcing tube o Defective cable o Def ective protective ground wire o Defective software “ when reloaded “ o Check +5v +/- 0.2v on board D100 and D160 and D220 o The error must be disregarded if the led on D220 flashes and if no firmware has been loaded: perform download Error number 401 ADC time out. The possible error causes are: o The A / D converter in the filament circuit does not convert o The 5v +/- 0.2v on test point D220.X18.A1 is defective o Board D220 is defective Error number 402 Minimum filament current. The possible error causes are: o
o
Intermediate circuit voltage in filament circuit Check fuse F19 on board D160 and lamp H2 missing : at X41.7 and X41.10 meas ure 230v +/- 10% Check wiring X41 – H1 Workstation selection defective: AP relay in H1 “ H1 test poi nt 50 = 0v ; AP1 test point point 51 = 24v +/- 15% ; AP2 test point 52 = 24v +/- 15% Check filament and high-voltage cable Check primary filament transformer windings “ R < 1 ohm “
o
Board D220 defective
o o o o
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Written by: E. de Schuttelaere
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
117 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Error number 403 Maximum tube cur curren rentt durin during g radio radiograp graphy. hy. The possibl possiblee error error ccaus auses es ar are: e: o The tube current is exceeded by 50% 100ms afte r high voltage has been switched ON o Tube adjustment defective, must be readjusted Error num ber 404 Maximum tube current current during fluoroscopy fluoroscopy.. The possible possible error error cause causess are: The tube current is exceeded by 50% 100ms after high voltage has been sw itched ON o Tube adjustment defective, must be readjusted o Error number 410 Processor time out. The possible error causes are: o Check voltage supply on D220 “ V66 = -15v +/- 10% ; V65 = +15v +/- 10% ; V65 = +15v +/- 10%; X19 / A8 = +24v +/- 15% “ o Board D220 is defective Error number 413 Tube current nominal value too high. The possible error causes are: o
Error in master / repeat the system configuration and Polydoros LX adjustment Error number 421 Tube current nominal value too high. The possible error causes are: Error in master / repeat the system configuration and Polydoros LX adjustment o
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Written by: E. de Schuttelaere
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
118 of 288
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
formatted by: E. de Schuttelaere
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Error number 422 Maximum filament current during tube current control. The possible error causes are: For 200 ms ms the tube current controller permits a filament current of 1.25x max. if the controller can not o Adjust during this period a warning is send o Check filament current o The tube is not correctly adjust, r eadjust it o The tube output is poorly o Check filament transformer; primary winding R < 1 ohm o
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Written by: E. de Schuttelaere
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
119 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
VOLTAGE SUPPLIES Error number 425 The - 15v “+/- 10%” has not reached –12v on board D220. The possible error causes are: o Check on D220 led V66 = -15v o o
Defective connection to board D100 ( cable X1 / 12 ; X1 / 38 ; 40 0v ) Check voltage on board D160 test point : X30 = -15v ; test point X29 = +15v ; test point X28 = 0v
Error number 426 The +15v “+/- 10%” has not reached +12v on board D220. The possible error causes are: o Check on D220 led V65 = +15v o Defective connection to board D100 ( cable X1 / 10 ; X1 / 38 ; 40 0v ) 0v o Check voltage on board D160 test point : X30 = -15v ; test point X29 = +15v ; test point X28 = 0v Error number 427 The +15v “+/- 10%” has not reached +12v on board D220. The possible error causes are: o Check on D220 led V64 = +15v o Defective connection to board D100 ( cable X1 / 22 ; X1 / 38 ; 40 0v ) o Check voltage on board D160 test point : X30 = -15v ; test point X29 = +15v ; test point X28 = 0v Error number 428 The +24v “+/- 15%” has not reached +20v on board D220. The possible error causes are: o Check on D220 voltage on point X19.A8 = +24v o Defective connection to board D100 ( cable X1 / 21 ; X1 / 38 ; 40 0v ) o Check voltage on board D160 test point : X13/12 = +24v ; test point X = 0v
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Written by: E. de Schuttelaere
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
120 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
FILAMENT INVERTER Error number 433 The filament inverter F0 ( small focus ) is too high. The possible error causes are: o Short circuit in the load circuit or filament circuit or high voltage cable o
Board D220 defective: remove cable X41.3 and X41.11 and perform a reset. If error 433 is displayed again the board D220 must be replace. If error 402 is displayed the board D220 is OK.
Error number 434 The filament inverter F1 ( large focus ) is too high. The possible error causes are: o Short circuit in the load circuit or filament circuit or high vo ltage cable o Board D220 defective: remove cable X41.9 and X41.12 and perform a reset. If error 433 is displayed again the board D220 must be replace. If error 402 is displayed the board D220 i s OK.
ERRORRS DURING DOWNLOAD Error number 471 to 483 Download default. The possible error causes are: o Repeat download and check the configuration
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Written by: E. de Schuttelaere
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
121 of 288
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
formatted by: E. de Schuttelaere
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
ERRORS FROM IONTOMAT PL Error number 510 Invalid Iontomat workstation. The possible error causes are: o The system configuration and programming is not OK o o o
The master board D100 has not send a valid Io ntomat workstation ( A – D ) If the plani-Iontomat has been programmed in the tomographic program, i t must be deleted and renamed ( it must not be copied )
Error number 550 Dose monitoring system has responded. The possible er ror causes are: o After 100 ms the dose counter is read. If half of the required dose has not been reached within the max, the error is displayed. o Check if the KV selection is in order to get enough power o The tube is not on the selected chamber o The diaphragm is closed o No signal from the Iontomat chamber “ cable connection….” o Defective detector o Board D100 defective
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Written by: E. de Schuttelaere
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
122 of 288
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
formatted by: E. de Schuttelaere
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
POWER PACK Error number 600 +15v ( +/- 10% ) faulty. The possible error causes are: o +5v +/- 0.2v defective o o o
Short circuit on board D100 or D220 or D110 Led V34 on board D160 does not light up: replace S NT power pack D160 X4.4 and X4.1 voltage on D160 = 230 v alternated ( +/- 10% ) is not correct
Error number 601 -15v ( +/- 10% ) faulty. The possible error causes are: o Short circuit on board D100 or D220 o Led V37 on board D160 does not light up: replace SNT power pack not correct o D160 X4.4 and X4.1 voltage on D160 = 230 v alternated ( +/- 1 0% ) is not Error number 602 Power contactor PS not OK. The possible error causes are: o After power on within 0.5 ms there is no acknowledge from the contactor PS ‘ D160.K10 no low signal change board D100 o = 0v / PSR to D160.X5.7 o Intermediate circuit default o Cable between D100.X5 and D160.X5 defective o Relay K10 on on board D160 defective: replace D160 A1 defective : 24V at 50hz and 29V at 60 60hz hz o Power contactor A2 , A1 o No acknowledge from contactor PSU on D100.X5.25 (24V alternated ) o The contactor PS is sticking or jamming
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Written by: E. de Schuttelaere
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
123 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Error number 603 power co c ontactor LS not OK du during ring init initializatio ialization. n. The possible possible error error causes are: o After power on within 1.5 D100 connects the charging contactor LS ‘ D160.K9 no low signal change board D100 o = 0v / LSR to D160.X5.5 o Cable between D100.X5 and D160.X5 defective o Relay K9 on board D160 defective : replace D160 50hz hz and 29V at 60hz o Power contactor A2 , A1 defective : 24V at 50 o No acknowledge from contactor LSU on D100.X.27 or D160.3.9 (24V alternated ) The contactor PS is sticking or jamming Error number 604 Intermediate circuit voltage ( UZ ) lower than 400v . The possible error causes are: o After power on within 1.5 D160 check the intermediate circuit o One phase is missing and the intermediate circuit is charging too slowly o The line voltage is not OK o UZ signal on D100.X20.17 and X20.19 is mi ssing “ on D100.X60 1V = 200V UZ o Wrong flat ribbon cable between D100.X20 and D115.X20 o Charging resistors R1 and R2 defective Error number 605 Intermediate circuit voltage ( UZ ) higher than 630v . The possible error causes are: o After power on within 1.5 D160 check the intermediate circuit o The line voltage is not OK o UZ signal on D100.X20.17 and X20.19 is missing “ on D100.X60 1V = 200V UZ betwee n D100.X20 and D115.X20 o Wrong flat ribbon cable between
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Written by: E. de Schuttelaere
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
124 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Error number 606 RANGE 0 and RANGE 1 default “ measuring value on D220 ) . The possible error causes are: D220.X19.A1 , A2 o Check function on D220 with SS OFF . test point D220.X19.A1 200ma: 0ma: RANGE 0 X19.A1 X19.A1 = 0V RANGE OK X19.A4 X19.A4 = 24V o with ZB ON and measuring range 20 RANGE 1 has no meaning with normal fluoroscopy ON and measuring range range 1ma: 1ma: RANGE 0 X19.A1 X19.A1 = 24V 24V o RANGE OK X19.A4 = 24V RANGE 1 X19.A2 = 24v RANGE OK X19.A3 = 0V If RANGE 0 and RANGE 1 do not comply with the mode operation, there is an error in cable X1 to D100 or on board D100 Replace board D220 •
•
Error number 608 not present or oil switch acknowledge missing . The possible error causes are: AP contactor o o
Check connector D160.X44.3-4 24v alternated at 50hz and 29V alternated at 60hz
Error number 628 Door error or open contact . The possible error causes are: o
The signal DOOR ( M-TK ) not equal to 1 ( door open )
Error number 629 AP contactor not present or oil switch acknowledge missing . The possible error causes are: o The N-TU1 “ OK” is actuated via TU1-N-TU2 signal. TU1-N-TU2 = 1 : tube selected this give: N-TU1-OK = 0 board D220 OK o D220 X19.A5 reverse to X19.A6 o X19.A6 = 24v and X19.A5 = 0v o Board D100 defective or board D220 defective
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Written by: E. de Schuttelaere
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
125 of 288
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
formatted by: E. de Schuttelaere
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Error number 633 U actual > 2 KV not OK: LS ; PS ; oil switch or tube assembly contactor are blocked. The possible error causes are: o Actual value acquisition D220 ( H1 ) defective o Flat ribbon cable from D220.X5 to D100.X5 defective o Board D100 defective o Radiation defect: tube assembly defective. Err or number 688 No dose from videomed DI. The possible possible error causes are: o Check the connection between Videomed DI and the generator o Videomed DI defective o No II input and output video o D100 board defective
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Written by: E. de Schuttelaere
Err or Co d es
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
126 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
o
o
Checking D220: “heating board” the flat connector connector between D1 D100 00 and D220 m must ust run in front of the holding shackle on H1. connect oscilloscope to point MA actual on D100.X61 D100.X61 and point KV actual on D10 D100.X61 0.X61 with trigger to point D100.X48 hand switch the SS OO on board D100: check the trigger. Switch back SS to On and release an exposure with 81kv,32mas, and 100ms. Observe the current. Increase the current only: if the measuring gives too high a current, readjust the tube. If impossible to readjust, exchange board D220. Clean the plug and replace Checking the high voltage cable: check if there is a visible tracks, and replace the cable if necessary. may ay be used on the the corona disk ref: 17 86 508 and the seal ref: 17 86 995 and ins ert them with HT silicone. No corona disk m transformer tank. 10mm oil must be present in the receptacle. The braiding can have a resistivity of one ohm / meter.
Error number 712 Plus KVo max tage with a ma mum value 1v of = 8010kv KV. The possible error causes are: error; side ofvalue high vol 0.X18.A7 andxiD100.X24: Check ofpositive the KV actual D22 o o o o o
Check the flat ribbon cable between D220.X1 and D100.X1 Kv board controller D100 defective Kv actual value acquisition defective: exchange board D220 Tube assembly or high voltage cable defective High voltage generator defective
Error number 713 Minus KV max error; negative side of high voltage with a maximum val ue of 80KV. The possible error causes are: o Check of the KV actual valu e D220.X18.A8 and D100.X23: 1v = 10kv o Check the flat ribbon cable between D220.X1 and D100.X1 o Kv board controller D100 defective o Kv actual value acquisition defectiv e: exchange board D220 o o
Tube assembly or high voltage cable defective High voltage generator defective
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Written by: E. de Schuttelaere
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
128 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Error number 714 Plus KV min error; the plus KV min monitoring becomes active if the +kv actual is more than 10KV smaller than the +KV nominal value. The possible error causes are: o Check of the KV actual value D220.X18.A8 and D100.X23: 1v = 10kv o Check the flat ribbon cable between D220.X1 and D100.X1 o Check the oscillating current on D100.X25 load “1v = 50A” o Check WR bridge diagonals o Check connection screw in the intermediate circuit and inverter Measure ure the int interm ermedi ediate ate circuit circuit voltage voltage on D11 D110.X 0.X2 2 and D110 D110.X .X1 1 o Meas 100 defe defect ctiive o Kv board controller D100 o Kv actual value acquisition defective: exchange board D220 o Tube assembly or high voltage cable defective o o o
High generator def ective IGBTvoltage defective Filament current too high, repeat tube adjustment
Error number 715 minus KV min error; the minus KV min monitoring becomes active if the -kv actual is more than 10KV smaller than the -KV nominal value. The possible error causes are:
o
Check of the KV actual value D220.X18.A8 and D100.X23: 1v = 10kv Check the flat ribbon cable between D220.X1 and D100.X1 Check the oscillating current on D100.X25 load “1v = 50A” Check WR bridge diagonals Check connection screw in the intermediate circuit and inverter Measure the intermediate circuit voltage on D110.X2 and D110.X1 Kv board controller D100 defective
o
Kv actual value acquisition defective: exchange board D220
o o o o o o
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Written by: E. de Schuttelaere
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
129 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
o o o o
Tube assembly or high voltage cable defective High voltage generator defective IGBT defective Filament current too high, repea t tube adjustment
Error number 803 Bridge short circuit in the inverter of the rotating anode starter. The possible error causes are: o The signal “R-KURZ” is displayed by led V154 on board D100 and by led V114 on board D115 o Check stator resistance at tube assembly connection: for 3 phase stator 0-1 2.0 - 2.6 ohm 0-11 2.0 - 2.6 ohm o for 2 phase stator 0-1 18 - 20 ohm 0-11 13 - 16 ohm o for Opti 154 - 2 phase stator 0-1 10 ohm approx. 0-11 10 ohm approx. o o o o o o
Stator configuration ? defective Board D100 or boardOK D115 Stator cable defective Measure the intermediate circuit voltage on board D115.X6 and X5 ; D110.X6.X2 and X5.X1 Check the intermediate circuit voltage connection terminals D165,D110,D115
Error number 805 No current in the main phase: during the run up, up, current is measured in the main phase ‘test point D100.X58 – X59’ X59’ 1v = A. the current must be > 1.5A. the error is displayed “no ROT green led on PC board D100 V153 does no nott light up”. The possible error causes are: o Interruption in the stator cable o Check activation of IGBT modules “ D100 – D115 OK ? “. o Check the current in the stator cable by means of the current transformer. o Measure the intermediate circuit voltage on D115.X6 and X5 and D110.X6.(X2) and X5.(X1) o Check the intermediate circuit voltage connection terminals D165 – D110 – D115 o
Check the stator resistances at the tube assembly “ see above”
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Written by: E. de Schuttelaere
Fun ct io nal Ch ec k s
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
130 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
REV 3
Error number 810 Stator contactor acknowledgement missing; stator contactor K3 has not switched over. The possible error causes are: o Contactor K3 defective o Acknowledgement interrupted. K3 ON = 0v K3 OFF = 24v o Check signal on D100.X20 – 23 STRSU o Board D100 defective
SI.PLX
SM 2305147-100
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Written by: E. de Schuttelaere
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
131 of 288
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
formatted by: E. de Schuttelaere
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
Part 4 : SX65/80 and LX80 ERRORS LIST Error Nbr
Item
000
Error description Details
001
Error description Details
SX65/80 and LX80 only Description
Invalid Init Data. f one of initthis block is wrong. This You errormay will try be to repeated tAhtelienaisttdata t ianllgfilnuiot rboloccukrveevsenneiw block are correct. configuart eeaacnhd fsoellleocw or configure the complete system from the scratch. Start of Service Session. The Service PC has contacted the XCU. No error, for information only. This error will be shown as error 41 of AP-I D 240 (XCU) in the error log
002
Error description Details
End of Service Session The Service PC has terminated the c onnection to the XCU (logged off). No error, for information only. This error will be shown as error 42 of AP-ID 240 (XCU) in the error log.
003
Error description Details
004
Error description Details Meaning
Start of Remote Service Session The Service PC has contacted the XCU via Modem. No error , for information only. This error will be shown as error 46 of AP-ID 240 (XCU) in the error log. End of Remote Service Session The Service PC has terminated the remote connection to the XCU (logged off). No error, for information only. This error will be shown as error 47 of AP-ID 240 (XCU) in the error log. Polydoros is no longer in the XCS-network Error 007 is most of the times accompanied by a 1 on the D100 in case of HW defects
In case of of SW-Resets 007 will heal itself
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Written by: E. de Schuttelaere
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
132 of 288
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
formatted by: E. de Schuttelaere
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
004 (continued)
Possible causes
Checking the terminal connectors At the terminal D320.X3.S and US or D320.X4.S and US, there must be either: o 2 terminal connectors installed o 1 terminal connector and 1 cable installed o 2 cables installed o o o o o o o
Actions
051
Error description
The terminal connector has Par t No.: 31 57 174. Cable not connected from XCU to generator Cable has a short circuit Hybrid-circuit of ARCNET is defective on any XCS component SW of a component sends ARCNET Reconfiguration interrupts intermittently Watchdog of Polydoros is active D100 or power supply defective
Check cabling for connection and shorts Check Hybrids and terminators o Check D100 D100 PROM checksum error (D100 checks the PROM's check sum during initialisation) o o
PROM D100.J15 defective (with D100 Part-No.: 37 75 256) PROM D100.J32 defective (with D100 Part-No.: 11 71 169) D100 defective
052
Error description Causes/Actions
Heating-Error during download (D220 sends telegram and not acknowledge) Repeat filament download Replace D220
053
Error description Causes/Actions
Image intensifier: invalid zoom level (XCU sends zoom level > 3 to D100 ) Check configuration
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Written by: E. de Schuttelaere
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
133 of 288
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
formatted by: E. de Schuttelaere
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
054
Error description Causes/Actions
055 056
o
The configuration might be modified without turning off/on the generator, then an unknown fluoroscopy curve selected, known to XCU but not yet known by the generator.
o
MANUAL.kV fluoroscopy selected in systems supporting pulsed fluoroscopy.
Error description
Invalid fluoroscopy fluoroscopy data . See Error 054
Error description
Invalid exposure mode
Causes/Actions
057
Invalid fluoroscopy data
Error description Causes/Actions
XCU sends request for impermissible mode of operation. Fluoro attachment feedback feedback (signal DLR_U) wrong Only with POLYDOROS SX65/80, (wiring diagram X2206-16.) In fluoroscopy mode the relay DLR is activated (displayed on the D100.X50.5). This signal comes to D111.X50.5 and activates the relay K1. Through the activated relay contact of K1.1/2 the contactor K6 is activated and the fluoroscopy attachment is added on. The fluoroscopy attachment feedback (DLR_U) is output via D111.X50.7 to D100.X50.7.
058
Error description
Wrong generator selection in the XCS software. software. The error is then generated due to the mism atch in the generator defined in the XCS conf igurations-SW and the Polydoros Host-SW ( ex: D100 PROM is LX lite and LX 80 is defined in the XCS configuration).
Causes/Actions
077
Error description Causes/Actions
078
Error description Causes/Actions
Configure the correct generator in the XCS service software .HS trigger of image system (ASU) is missing during pulsed Timeout exposure relea se se .HS fluoroscopy or indirect technique Check of HS trigger Scene too long !!!!!!plus d’info à mettre
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Written by: E. de Schuttelaere
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
134 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
100
Error description Causes/Actions
FILAMENT ERRORS Error description 119
Causes/Actions
(The software on the D100 is in an impermissible task state) Invalid task state D100 D100 (The o
PROM D100.J15 (for D100 SNo.: 37 75 256)
o
PROM D100.J32 (for D100 SNo.: 11 71 169)
o
D100
Time out filament circuit. When any interruption of the communication between D100 and D220 serial link (MPS, D100.X1.28, D220.X1.28). o Serial interface interrupted o D100, D220 defective Arcing tube H1 High tension transformer defective o Check screening and shielding of cabling o Check protective ground wire, all protective ground wire connections intended by the manufacturer must be made o Check firmware level D100, D160 and D220 D220)) o Check voltage power sup plies +5V ±0,2V (on D100, if the red LED(D220) is blinking and no firmware is loaded then Ignore error 119and perform download No Acknowledgment on transmitting transmitting to to the filament circuit. No communication in the serial line D100 to D220. Error 120 is output by D100 See error 119. 119. o o
120
Error description
121
Error description
No Acknowledgment on receiving receiving from from the filament circuit. No communication in the serial line D220 to D100 (reception). Error 121 is output by D100. See error 119. 119.
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Written by: E. de Schuttelaere
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
135 of 288
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
formatted by: E. de Schuttelaere
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
122 123
Error description
Buffer overflow on receiving from D220. D220. Error 122 is output by D100. See error 119 119
Error description
Invalid(wrong) answer from D220. Error 123 is output by D100. See error 119 119
IONTOMAT ERROR 125
Error description Causes/Actions
Timeout Iontomat Cable D100 to Iontomat
FILAMENT ERROR 401
Error description Causes/Actions
402
Error description Causes/Actions
Time-out Analog/Digital converter in D220 (no more conversion A/D ) Check Vcc = 5V ±0.2Volt on D220.X18.A1(if within tolerance D220 to be replaced) Mi nimum Current filament. The minimum filament current (50% nominal value) is monitored in standby Control in D220,D160 o Intermediate circuit voltage missing in the filament circuit at X41.7 and X41.10 , measure 230V ±10% o Check fuse F21, D160 path: Interruption in the filament path: o Check wiring X41 - H1 o Workstation selected, AP relay in H1 actuated o H1 test point 50 = 0V o Ap 1 test point 51 = 24V (±15%) o AP2 test point 52 = 24V (±15%) o Check filament and high-voltage cable o Check filament transformer primary winding (R < 1O hm, transformation ratio 32:9) If no error is found, replace board D220
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Written by: E. de Schuttelaere
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
136 of 288
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
formatted by: E. de Schuttelaere
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
403
Error description Causes/Actions
404
Error description Causes/Actions
410
Error description Causes/Actions
(+ 50% nominal value after 100 ms exposure) Maximum tube current current in radiogr radiography aphy (+ Proceed Tube adjustment Maximum tube current current in fluoroscopy fluoroscopy (+ (+ 50% nominal value after 100 ms fluoroscopy) Proceed Tube adjustment Processor timeout Check voltages on D220 o V66 - 15 V (± 10%) o V65 +15 V (± 10%) o V64 +15 V (± 10%) o X19/A8 + 24 V(± 15%) If no error is found, replace board D220
413
Error description Causes/Actions
Tube current nominal value too high (internal telegram error). Error in the master Proceed system configuration and POLYDOROS adjustment If no error is found, replace board D220
421 422 (Warning)
Error description
Fluoroscopy tube tube current nominal nominal value too high (internal high (internal telegram error). Error in the master
Causes/Actions Error description
If no error is found, replace board D220 Filament current too high (+2 5% maximum current current filament after 200 ms)
Causes/Actions
o o o
Check the filament current with cathotest The tube emits very badly Perform tube adjust (tube not adjusted properly)
o
Check filament transformer primary winding (R < 1Ohm, transformation ratio 32:9)
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Written by: E. de Schuttelaere
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
137 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
D220 POWER SUPPLY ERRORS 425
Error description Causes/Actions
426
Error description Causes/Actions
-15V power supply defective on D220. D220 . Smaller than –12V (absolute value) on D220 o Check voltage at D220.V66 = -15V (±10%) o Check connection to D100 (lead X1.12, X1.38-40 0V) o Check voltage on D160 o X30 = -15V (±10%) o X29 = +15V (±10%) o X28 = 0V +15V power supply defective on D220. D220. Smaller than +12V on D2 D220 20 o Check voltage at D220.V65 =+15V (±10%) o Check connection to D100 (lead X1.10, X1.38-40 0V) Check voltage on D160 o X30 = -15V (±10%) o X29 = +15V (±10%) o X28 = 0V +15V (for Digital) power supply defective on D220. D220 . Smaller than +12V on D2 D220 20 o Check voltage at D220.V66 =+15V (±10%) o Check connection to D100 (lead X1.22, X1.38-40 0V) o Check voltage on D160 o X30 = -15V (±10%) o X29 = +15V (±10%) o X28 = 0V o
427
Error description Causes/Actions
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Written by: E. de Schuttelaere
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
138 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
428
Error description Causes/Actions
+24V power supply defective on D220. D220. Smaller than +20V on D220 o Check voltage on D220.X19.A8 (±15%) o Check connection to D100 (lead X1.21; X1.38-40) o Check voltage on D160: o D160.X13/14 = 24V (±15%) o o
o
o
D160.X28 It might as well =be0V the case that the power fail signal X1 on D320 (Polydoros SX65/80 series) or D200 (Polydoros LX series) is not detected and therefore, each time you switch on, the error is entered into the error log. Input check: Remove cable D160.X1 coming from D320 (Polydoros SX65/80 series) or D200 (Polydoros LX series). The Hex display on D320 or D200 should indicate F4. If not, D320 or D200 are defective. Output check: Connect a voltmeter (DC) to D160.X12.2 (power fail) and X12.1(ground) for the Polydoros LX series or D160.X121.2 and X121.1 for the Polydoros SX65/80 series; fr om 5V to 0V. when switching off the generator, voltage should suddenly change from
FILAMENT INVERTER ERROR 433
Error description Causes/Actions
Current in the filament inverter FO (large focal spot) too high circuit: o Short circuit in the charging circuit: o
o
Wiring X41, filament transformer, high-voltage cable, filament or D220 defective. Eject leads X41.3 and X41.1 1: 1: o if error 433 occur s again after reset, D220 must be replaced o if error 402 occurs, D220 is OK Check filament transformer. Primary winding R < 1Ohm, transformation ratio 32:9
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Written by: E. de Schuttelaere
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
139 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
434
Error description Causes/Actions
Current in the filament inverter F1 (small focal spot) too high o o
Short circuit in the charging circuit Wiring X41, filament transformer, high-voltage cable, filament or D220 defective. Eject leads X41.9 and X41.12 o if error 434 occurs anew after reset, D220 must be replaced o
o
if error 402 occurs, D220.isPrimary OK winding R < 1Ohm, transformation ratio 32:9 Check filament transformer former.
FILAMENT DOWNLOAD ERROR 485
Error description Causes/Actions
Error when deleting the Flash-PROM Repeat filament download If no error is found, replace board D220
486
Error description Causes/Actions
Check sum Error of the Flash-PROM Repeat filament download If no error is found, replace board D220
487
Error description Causes/Actions
Bank switching Error Repeat filament download
488
Error description Causes/Actions
If no error is found, replace board D220 Programming Flash-PROM Error Repeat filament download If no error is found, replace board D220
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Written by: E. de Schuttelaere
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
140 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
IONTOMAT PL ERROR 505 510
Error description Causes/Actions Error description
Causes/Actions
511
512
Error description Causes/Actions Error description Causes/Actions
513
Error description Causes/Actions
514
Error description
515
Causes/Actions Error description Causes/Actions
D190 RAM record impossible Invalid iontomat configuration. configuration. D190 D19 D190 defe defect ctiv ivee Inadmissible IONTOMAT IONTOMAT workstation. A checked is performed in D100 when the IONTOMAT is involved (exposure or fluoroscopy ) for validation. When the check fails none or wrong workstation is generated . Check system system conf configu igurati ration. on. Check IONTOMAT workstations setup Inco rrect film-screen film-screen combination ( H,U,D) detected . o Check system configuration o D190 defective Incorrect tomo time detected system em config configurat uration ion o Check syst o D190 defective Incorrect detector in the EEPROM o Check system configuration o D190 defective Incorrect IONTOMAT mode Incorrect plug position in the EEPROM o Check system configuration o D190 defective
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Written by: E. de Schuttelaere
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
141 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
550
Error description Causes/Actions
Dose too low. low. (-50% nominal dose after Max exposure time) o Manipulation error (User): o Tube not aligned with selected IONTOMAT chamber o Collimator closed o Wrong choice of the exp osure kV o
551
Error description Causes/Actions
Errors: o Wrong IONTOMAT workstation programmed, check system configuration measuri ng point D100.X63 DL_IN o No signal from IONTOMAT chamber at measuring o Check detector and cabling o D100 defective Dose too low in tomography tomography.. (-50% nominal dose after end of tomo exposure time) o
o
552
Error description Causes/Actions
560
Error description Causes/Actions
Manipulation error (User): o Tube not aligned with selected IONTOMAT chamber o Collimator closed o Wrong choice of the exposure kV Errors: o Wrong IONTOMAT workstation programmed, check system configuration o No signal from IONTOMAT chamber at measuring point D100.X63 DL_IN o Check detector and cabling o D100 defective
Dose supervision supervision max. for tom tomography ography. Dose reached before the end of the tomography time. Select higher exposure parameters Invalid measurement field in Direct technique o o
D190 defective Error in kV
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Written by: E. de Schuttelaere
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
142 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
561
Error description Causes/Actions
Invalid max time ( > 10s) 10s) D190 defective
562
Error description Causes/Actions
Invalid mea suring field (No (No scan field selected) o Check system configuration o D190 defective
570
Error description
Checksum error detecto r
Causes/Actions
571
Error description Causes/Actions
572
Error description Causes/Actions
573
Error description Causes/Actions
575
Error description Causes/Actions
580
Error description Causes/Actions
581
Error description Causes/Actions
D190 defective Checksum error HUD D190 defective Checksum error lead time value D190 defective Checksum error voltage correction D190 defective Checksum error density correction D190 defective Wrong dose value o Check system configuration o D190 defective Wrong lead time value o Check system configur ation o D190 defective
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Written by: E. de Schuttelaere
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
143 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
582
Error description Causes/Actions
Wrong voltage correction o Check system configuration o D190
590
Error description Causes/Actions
mAs value not sent sent o Check system configuration
Error description
D190 defective D100 defective Bad tube AP selection o o
591
Causes/Actions
Check system configuration
POWER SUPPLY ERRORS 600
Error description Causes/Actions
+15 V Power supply SNT device (Chopped Power Supply) defective o Check LED V72 in D160 connected to the +15 V power supply o Check D100,D220,D110 also connected to the +15 power supply o Check the +5.1V provided by the SNT device (LED 74 in D160) to ensure that the input of the SNT device is OK o Check voltage on D160.X4.4 and X4.1 (230 V ~ (± 10%) input of the SNT device ). Change SNT Power supply if the input is OK
601
Error description Causes/Actions
-15 V Power supply SNT device (Chopped Power Supply) defective defective t o the -15 V power supply s upply o Check LED V73 in D160 connected to o Check D100,D220,D190 also connected to the -15 power supply o Check the +5.1V pr ovided by the SNT device (LED 74 in D160) to ensure that the input of the SNT device is OK o Check voltage on D160.X4.4 and X4.1 (230 V ~ (± 10%) input of the SNT device ). Change SNT Power supply if the input is OK
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Written by: E. de Schuttelaere
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
144 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
602
Error description
Causes/Actions
Problem with the Power Power contactor (PS). (PS). o When no acknowledgment 0.5 s after the command from D100 in the initialisation step o When the power contactor drops during the normal usage of the generator Check of the Drive "Power" relay o Drive "Power" relay defective: D160.K5 (SX65/80) or D160.K10 (LX30/50(Lite)/80). o Check the power supply of the Drive "Power" relay (U24VE) o Check the Drive "Power" relay command in D160 .X5.7 (0V when commanded) o Check cable from D100.X7 to D160.X7. o Check D100 output When the Drive "Power" relay is working properly o Check the PS contactor A2, A1 power supply : 24V~ ±10% (50Hz) or 29V~ ±10% (60Hz) o Check contactor acknowledgment (PSU signal) at D160 X5.25 and D100.X5.25 : 24V~ o
603
Error description
Causes/Actions
±10% Contactor sticks or jams.
Problem with the Charging Charging contactor (LS) (LS) When no acknowledgment 1.5 s (SX 65/80) or 5 s ((LX30/50(Lite)/80) after the command from D100 in the initialisation step Check of the Drive "Charging" relay defe ctive: D160.K4 (SX65/80) or D160.K9 (LX30/50(Lite)/80). o Drive "Charging" relay defective: o Check the power supply of the Drive "Power" relay (U24VE) o Check the Drive "Power" relay command in D160.X5.5 (0V when commanded) o Check cable from D100.X5 to D160.X5. o Check D100 output When the Drive "Charging" relay is working properly o Check the LS contactor A2, A1 power supply : 24V~ ±10% (50Hz) or 29V~ ±10% (60Hz) o
Check contactor acknowledgment (PSU signal) at D160 X5.27 and D100.X5.27 : 24V~ ±10%
o
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Written by: E. de Schuttelaere
Contactor sticks or jams
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
145 of 288
Theo Theory ry
Servic Serv ic e n o t es
formatted by: E. de Schuttelaere
Refer Referenc ence e Mat er i al s
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
604
Error description
Causes/Actions
605
Error description Causes/Actions
Intermediate circuit circuit voltage (Inverter (Inverter power supp supply ly UZ) < 400V . Caution! Direct voltage o When < 400 V 5s after “Charging” relay commanded by D160 in the initialisation step o When the voltage drops down < 400 V during the normal usage of the generator o Input power supply defective (Phase missing), intermediate circuit is charged too slowly o Check line voltages o Check UZACT signal at D100.X20.17 and X20.19 (1V = 50V / UZact = 1,4 x Umains) o Check ribbon cable from D100.X20 to D115.X20 o Check Charging resistors R1, R2 ,replace if defective Intermediate circuit circuit voltage (Inverter (Inverter power supply UZ) UZ) >630V . Caution! Direct voltage o When > 630 V 5s after “Charging” relay comm anded by D160 in the initialisation step o Check line voltages o Measuring the line resistance o o
Check Signal at D100.X20.17 and X20.19 (1V = 50V / UZact = 1,4 x Umains) Check UZACT ribbon cable from D100.X20 to D115.X20.
Al ig nm nment ent Cal i b r at i o n
Com Compo po nent L o c at i o n s
Err or Co d es
Fun ct io nal Ch ec k s
Written by: E. de Schuttelaere
Lo gic/B gi c/B lo ck Prev Prevent entiv iv e Softw Sof tw are D Dii ag r am s Mai n t en an c e Di ag n o s t i c s
controlled by: J.Aupied
146 of 288
Theo Theory ry
Servic Serv ic e n o t es
Refer Referenc ence e Mat er i al s
formatted by: E. de Schuttelaere
Not es
date 27-Sept-2004
GE MEDICAL SYSTEMS
MVS DI EUROPE
SI.PLX
SM 2305147-100
REV 3
606
Error description
Causes/Actions
The signals Range0_OK and range1_OK being the acknowledgment of RANGE Error in D220. D220.The the tube measuring ranges on D220 for exposure mode (signal Range0) and fluoroscopy mode (Signal Range1) Range1) Check function at SS OFF on D220. Test points: D220.X19.A1, A2 (wiring diagram X2206-18 and 22 / X2169-18 and 22): 1/ With ZB ON: measuring range 200mA; 0" ”OK” X19.A4 = 24V (±15%) 200mA; -> "RANGE "RANGE 0" X19.A1 = 0V "RANGE 1" without significance 2. With normal FL ON: meas uring range 1mA; "RANGE 0" X19.A1 = 24 V (±15%) ( ±15%) "RANGE 0" ”OK” X19.A4 = 0V RANGE 1" X19.A2 = 24V (±15%) -> "RANGE 1" ”OK” X19.A3 = 0V If the "RANGE 0" and "RANGE 1" signals do not agree with the operating m ode, there is a fault in the cable X1 to D100 or on D100.
608
Error description Causes/Actions
610
Error description Causes/Actions
If the signals "RANGE 0"_OK and "RANGE 1"_OK are wrong with correct commands, D220 must be replaced. Workstation(tube) sseelection cco ontactor n no ot p prresent, no no fe feedback fr from oil solenoid Check LED D160 V79 connected to oil solenoid feedback Check on D160.X44.3-4 D160.X44.3-4 the voltage 24 V ~ ± 10% (50 Hz) or 29 V ~ ± 10% (60 Hz) Invalid range of tube current 10mA
View more...
Comments
