Panasonic DP-8020e Service Handbook

Order Number: MGCS060808C0 H21

Digital Imaging Systems

DP-8020E/8020P/8016P [ Version 1.0 ]

WARNING This service information is designed for experienced repair technicians only and is not intended for use by the general public. It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product. Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service or repair the product or products dealt within this service information by anyone else could result in serious injury or death.

© 2006 Panasonic Communications Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law. Published in Japan.

2

General Annotations 9. Important Notice (Especially in those countries belonging to the European Union): This product is fully compliant with the national laws transposed from the EU Directive on the restriction of the use of certain hazardous substances (RoHS) in electrical and electronic equipment, effective 1st July 2006 in the EU countries. In order for the product to comply with the RoHS Directive, the six particular substances (lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls, and polybrominated diphenyl ethers) have been either totally eliminated or limited to the concentration level below maximum allowed. Consequently spare parts have been changed to RoHS-compliant parts where applicable. To ensure compliance with the spare parts application of the RoHS legislation, please make sure to follow the details provided in this manual when ordering spare parts and carrying out repairs.

The contents of this Service Handbook, and the Specifications are subject to change without notice. Panasonic Communications Co., Ltd. reserves the right to make improvements in the product design without reservation and without notice. Published in Japan.

3

Important Notice Please read these Instructions completely BEFORE installing any optional accessories. Installing the additional board, or connector with the power ON (only the power switch OFF) could damage the SPC, and/or SC board. If the Hard Disk Drive Unit is installed, to prevent a Disk Scan Function from being performed (similar to when the power is abruptly interrupted to the PC), it is important to follow the step sequence below when turning OFF the Power Switch on the machine.

How to turn OFF the Power:



1. If the machine is in the "ENERGY SAVER (Shutdown Mode)", you may turn the Power Switch on the machine to the OFF position. If it is not in the "ENERGY SAVER (Shutdown Mode)", continue to step 2 below. 2. Press "FUNCTION" and "ENERGY SAVER" keys simultaneously first. 3. Wait approximately 10 seconds while the machine writes the closing status onto the Hard Disk Drive Unit, and advances into "ENERGY SAVER MODE". 4. Turn the Power Switch on the machine to the OFF position. 5. Disconnect the Telephone Line Cable, if the Fax Option is installed. 6. Unplug the AC Power Cord. (When the Fax option is installed, there is a remote possibility of electrocution when servicing the unit during a Lightning Storm. As a precaution, disconnect the Telephone Line Cable first, before unplugging the AC Power Cord.

WARNING This service information is designed for experienced repair technicians only and is not intended for use by the general public. It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product. Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service or repair the product or products dealt within this service information by anyone else could result in serious injury or death. * The specifications are subject to change without notice. Panasonic Communications Co., Ltd. reserves the right to make improvements in the product design without reservation, and without notice.

4

5

Caution:

Depending on your machine’s model, it may weight approximately 93.26 - 98.33 lb (42.3 - 44.6 kg) without any options. To prevent injuries, use the appropriate number of personnel to lift, or move the machine as illustrated. Do not lift the machine by the Paper Tray as it may cause damage and/or bodily injury.

Note: Refer to the Installation Instructions when installing the machine.

6

Precautions For Your Safety To prevent severe injury and loss of life, read this section carefully before servicing the Panasonic machine to ensure proper and safe operation of your machine. Please ensure that the machine is installed near a wall outlet and is easily accessible. This section explains the Warnings and Cautions used in the machine and/or this manual.

WARNING: Denotes a potential hazard that could result in serious injury or death. CAUTION: Denotes hazards that could result in minor injury or damage to the machine.

This section also explains the Warnings and Cautions used in the machine and/or this manual. These symbols are used to alert operators to a specific operating procedure that must not be performed. These symbols are used to alert operators to a specific operating procedure that must be emphasized in order to operate the machine safely.

WARNING Power and Ground Connection Cautions Ensure that the plug connection is free of dust. In a damp environment, a contaminated connector can draw a significant amount of current that can generate heat and eventually cause fire if left unattended over an extended period of time. Always use the power cord provided with your machine. When an extension power cord is required, always use a properly rated cord. 120 V/15 A or AC 220 - 240V/10 A If you use a cord with an unspecified current rating, it may be underrated, and the machine, or plug may emit smoke, orbecome hot to the touch. Do not attempt to repair, pull, bend, chafe or otherwise damage the power cord. Do not place a heavy object on the cord. A damaged cord can cause fire or electric shocks. Never touch a power cord with wet hands. Danger of electric shock exists. If the power cord is damaged, or insulated wires are exposed, contact the authorized Panasonic dealer for a replacement. Using a damaged cord can cause fire or electric shocks. Stop operation immediately if your machine emits smoke, excessive heat, unusual noise, or abnormal smell, or if water is spilt onto the machine. These conditions can cause fire. Immediately switch Off and unplug the machine, and contact the authorized Panasonic . dealer. Do not disconnect or reconnect the machine while the power switch is in the On position. Disconnecting a live connector can cause arcing, consequently deforming the plug and cause fire. When disconnecting the machine, grasp the plug instead of the cord. Pulling on a cord forcibly can damage it, and cause fire, or an electric shock. When the machine is not used over an extended period of time, switch it Off and unplug it. If an unused machine is left connected to a power source for a long period, degraded insulation can cause electric shocks, current leakage or fire. Be sure to switch Off, and unplug the machine before accessing the interior of the machine for cleaning, maintenance or fault clearance. Access to a live machine's interior can cause an electric shock.

7

Once a month, unplug the machine and check the power cord for the following. If you notice any unusual condition, contact your authorized Panasonic . dealer The power cord is plugged firmly into the receptacle. The plug is not excessively heated, rusted, or bent. The plug and receptacle are free of dust. The cord is not cracked or frayed.

Operating Safeguards Do not touch areas where these caution labels are attached to, the surface may be very hot and may cause severe burns. Do not place any liquid container such as a vase, or coffee cup on the machine. Spilt water can cause fire or shock hazard. Do not place any metal parts such as staples or clips on the machine. If metal and flammable parts get into the machine, they can short-circuit internal components, and cause fire or electric shocks. If debris (metal or liquid) gets into the machine, switch Off and unplug the machine immediately. Operating a debris-contaminated machine can cause fire or electric shock. Do not try to alter the machine configuration or modify any parts. An unauthorized modification can cause smoke or fire.

Consumable Safeguards Never dispose of toner, toner cartridge, or a waste toner container into an open flame.Toner remaining in the cartridge/bottle can cause an explosion, burns and/or injuries. Keep button batteries/stamp out of the reach of children to prevent chocking or poisoning. If a button battery/stamp is swallowed accidentally, get medical treatment immediately,

Notice: California only: This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material - special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate

CAUTION Installation and Relocation Cautions Do not place the machine near heaters or volatile, flammable, or combustible materials such as curtains that may catch fire. Do not place the machine in a hot, humid, dusty, or poorly ventilated environment. Prolonged exposure to these adverse conditions can cause fire or electric shocks. Place the machine on a level and sturdy surface that can withstand the weight of the machine. Refer to the Specifications section for the weight of the machine. If tilted, the machine may tip-over and cause injuries. When relocating the machine, remove the toner and/or developer, and pack the machine e with proper packing materials for shipping.

When moving the machine, be sure to unplug the power cord from the outlet. If the machine is moved with the power cord attached, it can cause damage to the cord which could result in fire or electric shock.

8

CAUTION Operating Safeguards Do not place a magnet near the safety switch of the machine. A magnet can activate the machine accidentally, resulting in injuries. Do not use a highly flammable spray, or solvent near the machine. It can cause fire. When copying a thick document, do not use excessive force to press it against the scanning glass. The glass may break and cause injuries. Never touch a labelled area found on, or near the heat roller. You can get burnt. If a sheet of paper is wrapped around the heat roller, do not try to remove it yourself to avoid injuries or burns. Switch Off the machine immediately, and wait until it cools down. Do not use conductive paper, e.g. folding paper, carbon paper and coated paper. When a paper jam occurs, they can cause a short circuit and fire. Do not place any heavy object on the machine. An off-balance machine can tip-over, or the heavy object can fall, causing damage and/or injuries. Keep the room ventilated when using the machine for an extended period of time to minimize the ozone density in the air. When copying with the document cover open, do not look directly at the exposure lamp. Direct eye exposure can cause eye fatigue or eye injury. Pull the paper trays out slowly to prevent injuries. When removing jammed paper, make sure that no pieces of torn paper are left in the machine. A piece of paper remaining in the machine can cause fire. If a sheet of paper is wrapped around the heat roller, or when clearing a jammed paper that is difficult or impossible to see, do not try to remove it by yourself. Doing so can cause injuries or burns. Switch Off the machine immediately, and wait until it cools down.

Consumable Safeguards Never heat the drum cartridge, or scratch its surface. A heated, or scratched drum can be hazardous to your health. Do not mix new and old batteries together, as they can burst or leak, causing a fire or injuries. Be sure to use the specified type of batteries . only. Ensure that batteries are installed with correct polarity. Incorrectly installed batteries can burst or leak, resulting in spillage or injuries.

Others When clearing a paper jam or other fault, follow the appropriate procedure given in this manual. The machine has a built-in circuit for protection against lightning-induced surge current. If lightning strikes in your neighborhood, maintain an ample distance from the machine, and do not touch it until the lightning stops. If you notice flickering, distorted images, or noises on your audio-visual units, your machine may be causing radio interference. Switch it Off, and if the interference disappears, the machine is the cause of the radio interference. Perform the following procedure until the interference is corrected. Move the machine, and theTV and/or radio away from each other. Reposition or reorient the machine, and theTV and/or radio. Unplug the machine, TV and/or radio, and replug them into outlets operating on different circuits. Reorient the TV and/or radio antennas, and cables until the interference stops. For an outdoor antenna, ask your local electrician for support. Use a coaxial cable antenna.

9

10

11

12

Table of Contents Specifications ........................................ 14

5.14. Paper Tray ........................................... 246

1.1.

Control Panel ..........................................14

5.15. Automatic Document Feeder ............... 248

1.2.

Specifications Table................................16

1.3.

Fax, Printer and Internet Fax Functions .........................................26

5.16. Inverting Automatic Document Feeder (For DP-8020E) .................................... 256

1.4.

System Combination...............................37

5.18. 2nd/4th Paper Tray .............................. 280

1.5.

Options List.............................................38

5.19. 3rd Paper Tray ..................................... 286

5.17. PC Boards/Harnesses.......................... 274

5.20. Packing and Accessories 1. For USA and Canada ...................... 292

Maintenance, Adjustments and Check Points .......................................... 39

5.21. Packing and Accessories 2. For China ......................................... 294

2.1.

Preventive Maintenance .........................39

2.2.

Required Tools .......................................41

2.3.

Preventive Maintenance Points ..............42

5.22. Packing and Accessories 3. For Other Destinations (except USA, Canada and China) ........ 296

2.4.

Preventive Maintenance Check List ...............................................44

5.23. Printer Controller Module for PCL6 ............................................... 298

2.5.

Resetting the P/M (Preventive Maintenance) Counter .........46

5.24. Printer Controller Module for PS/PCL6 ......................................... 300

2.6.

Lubrication Point List ..............................47

5.25. Fax Communication Board................... 302

2.7.

Updating the Firmware ...........................48

5.26. Keyboard Option .................................. 306

2.8.

Copy Quality Adjustment Procedure (Order) ....................................................56

5.27. Hard Disk Drive Unit............................. 308

2.9.

Adjusting the Printer Registration, LSU Image Side to Side .........................59

5.29. i-ADF Packing and Accessories ........... 312

5.28. Accounting Software ............................ 310

2.10. Signal Waveform ....................................63

5.30. ADF Packing and Accessories ............. 314

Troubleshooting .................................. 124

5.31. 2nd/4th Paper Tray and 3rd Paper Tray Packing and Accessories .......................................... 316

3.1.

Error Codes (For Copier) ......................124

3.2.

Information Codes Table (For Facsimile)......................................134

5.32. Dehumidifier Heater Kit (For Main Unit) ..................................... 318 5.33. Dehumidifier Heater Kit (For Optional Paper Tray(s)) ................ 320

Service Modes...................................... 141 4.1.

Service Modes (For Copier)..................141

4.2.

Service Modes (For Facsimile) .............169

5.34. Key Counter Harness Kit ..................... 322 5.35. Hardware Identification Template ........ 324

Alphanumerical Parts List .................. 328

Exploded View & Parts List ................ 198 5.1.

Destination Codes ................................199

5.2.

Cover Assembly....................................200

5.3.

Scanner Unit .........................................204

5.4.

Control Panel Unit.................................208

5.5.

Paper Transportation ............................212

5.6.

Automatic Duplex Unit ..........................216

5.7.

Electrical Parts......................................220

5.8.

Frame Parts ..........................................224

5.9.

Fuser Unit .............................................228

5.10. Hopper Unit...........................................232 5.11. Developer Unit ......................................234 5.12. Drum Unit..............................................238 5.13. Drive Unit ..............................................242

13

DP-8020E/8020P/8016P

1 Specifications 1.1.

Control Panel

DP-8020 Series for PU (USA/Canada, etc.) DP-8020E

DP-8020P

DP-8016P

OPTIONS (DP-8020E/8020P only)

Note1: 1. DP-8020P is not available for USA and Canada. 2. Model availability may differ as per destination. Please ask your sales company for details. Note2: LCD Display Brightness Adjustment To adjust the brightness of the LCD display, press and while holding down the "CLEAR" key, keep pressing the "ORIGINAL SIZE", or the "COPY SIZE" key until the desired brightness is achieved. ORIGINAL SIZE: Dimmer COPY SIZE : Brighter

14 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

DP-8020 Series for Other Destinations DP-8020E

DP-8020P

DP-8016P

OPTIONS (DP-8020E/8020P only)

Note: Model availability may differ as per destination. Please ask your sales company for details.

15 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

1.2.

Specifications Table

1.2.1.

Copy Function Items

Basic Specifications 1 Type 2 Platen 3 Original Position Platen ADF / i-ADF 4 Recording Paper Path 5 Face Up / Face Down 6 Drum 7 Copy Process 8 Developing Process 9 Toner Recycle 10 Fusing System 11 Max Original Size 12 Paper Tray

Description DP-8020E DP-8020P DP-8016P Desktop Fixed Left / Rear Left / Center Center Face Down Organic Photo Conductor (OPC) Dry Electrostatic System Dry Dual Components No Heat & Pressure Ledger (11 x 17 in) / A3 (297 x 420 mm) Paper Size LDR, LGL, LTR, LTR-R, INV-R A3, A4, A4-R, A5, A5-R, B4, FLS A3, A4, A4-R, B4, B5, B5-R LDR, LGL, LTR, LTR-R, INV-R

Bypass Tray

Bypass Tray (Envelope)

A3, A4, A4-R, A5-R, B4, FLS A3, A4, A4-R, B4, B5, B5-R #10 (4.1 x 9.5 in) DL (4.3 x 8.7 in)

13 Paper Weight Paper Tray Bypass Tray ADU 14 Warm-up Time

16-24 lb (60 - 90 g/m2) 15-34 lb (55 - 133 g/m2) 17-24 lb (64 - 90 g/m2) Less than 30 sec

15 First Copy Time

Less than 6.9 sec

16 Copy Speed Ledger A3 Legal / B4 / FLS Letter-R / A4-R Letter / A4 Invoice-R / A5-R

Remarks

11 cpm 11 cpm 13 cpm 16 cpm / 15 cpm 20 cpm 20 cpm

9 cpm 10 cpm 11 cpm 13 cpm 16 cpm 16 cpm

For USA and Canada For EU FLS = 8 x 13 in, 8.5 x 13 in For Other Destinations For USA and Canada For EU FLS = 8 x 13 in, 8.5 x 13 in For Other Destinations For USA and Canada For EU

For DP-8020E 68 °F (20 °C) From Platen, Letter/ A4 Portrait,1st Paper Tray. Period between Start Key is pressed and Paper ejected to the Exit Tray. When LSU is ready.

From Platen, 1st Paper Tray, and Paper ejected to the Exit Tray, LSU is ready, and Continuous Copy.

16 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Items

Description DP-8020E DP-8020P DP-8016P

17 Zoom Enlargement Selected Original size / Copy size Reduction Selected Original size / Copy size Zoom 50 - 200% 18 Paper Feed Front Loading Universal Paper Tray Paper Tray Capacity 550 sheets x 1 Auto Size Setting No Low Level Warning Empty Only Bypass Paper Tray Capacity 50 sheets Auto Size Setting Yes Paper Capacity 600 sheets (Std. Configuration) 19 Multi Copy Range 999 sheets 20 Gradation Text Bi-Level Text / Photo 256 steps Photo 256 steps 21 Resolution 600 dpi 22 Standard Sorting Memory 16 MB Size 23 Standard Page Memory 32 MB Size 24 Exit Tray Capacity Standard: 250 sheets 25 Color No 26 Dimensions 22.0 x 21.9 x 18.1 in (558 x 557 x 460 mm) (W x D x H) 33.2 x 24.6 x 24.5 in (844 x 624 x 623 mm) 27 Operating Space 33.2 x 22.2 in (W x D) (844 x 565 mm)

Weight

DP-8020E

95.46 lb (43.3 Kg)

DP-8020P*/ 8016P/

93.26 lb (42.3 Kg)

DP-8020E

98.33 lb (44.6 Kg)

DP-8020P/ 8016P

Remarks

1% Step

LTR / A4 : 20 lb (75 g/m2) Control Panel Selectable

LTR / A4 : 20 lb (75 g/m2) Paper Tray 1 (Std) + Bypass Paper Tray

Halftone by Error Diffusion Scanning and Printing.

H: To Platen Glass. Includes ADF / Bypass Paper Tray.

Includes Bypass Paper Tray. For PU (USA/Canada, etc.) *DP-8020P is not available for USA and Canada

For EU and Other Destinations 96.12 lb (43.6 Kg)

17 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Items Options 1 Paper Feed System 550 sheets 2nd Paper Tray Paper Size Detection Low Level Paper Warning 550 sheets 3rd Paper Tray Paper Size Detection Low Level Paper Warning 550 sheets 4th Paper Tray Paper Size Detection Low Level Paper Warning Max. Paper Capacity

Description DP-8020E DP-8020P DP-8016P

Remarks LTR / A4 : 20 lb (75 g/m2)

Yes Manual

Control Panel Selectable

Empty Only Yes

No Manual

Control Panel Selectable

Empty Only Yes

No Manual

Control Panel Selectable

Empty Only 1, 150 sheets

2, 250 sheets

2 Stand Stand for 4*-Paper Tray Configuration

Option

Stand for 3*-Paper Tray Configuration

Option

Stand for 2-Paper Tray Configuration

Option

Stand for 1-Paper Tray Configuration

Option

Low Stand with Casters DA1D18C (For USA and Canada Only) DA-DA191-PE (For Other Destinations) Low Stand with Casters DA1D18C (For USA and Canada Only) DA-DA190-PE (For Other Destinations) Mid Stand with Casters DA1D18B (For USA and Canada Only) DA-DA189-PE (For Other Destinations) High Stand with Casters DA1D18A (For USA and Canada Only) DA-DA188-PE (For Other Destinations)

Note: The same Stand (DA1D18C) is used for either 3 or 4 Paper Tray Configuration for USA and Canada. Option For USA and Canada 3 Platen Cover Standard For EU and Other Destinations Free Stop Yes From 30 to 70 degrees.

18 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Items 4 ADF Single Side Type Original Set Scanning Method Capacity (Originals) SADF Mode Free Stop 5 Inverting ADF (i-ADF) Duplex Type Original Set Scanning Method Capacity (Originals)

6

7 8 9 10

Description DP-8020E DP-8020P DP-8016P Option Face Up Sheet Through 50 sheets Yes Yes Option

LTR / A4 : 20 lb (75 g/m2) From 30 to 70 degrees.

No Face Up Sheet Through 50 sheets

SADF Mode

Yes

Free Stop Exit Tray (Inner) Tray Position Number of Bins Face Up / Face Down Bin Capacity Multi Tray Function Shift Tray Function Finisher Exit Tray (Outer) Automatic Duplex Unit Counter

Yes

LTR / A4 : 20 lb (75 g/m2) Available for single side scanning only. From 30 to 70 degrees.

Inner 1 Face Down 250 sheets No No No No Standard : DP-8020E

Key Counter Capability

Option

11 Dehumidifier 12 Sorting Image Memory Optional Image Memory 1 (16MB) Optional Image Memory 2 (64MB) Optional Image Memory 3 (128MB)

Option

13 Hard Disk Drive

Remarks

The Harness Kit contains only Harnesses, Bracket and a Screw. Supplied as a Service Part.

Yes Unit comes standard with 16 MB. 1-Slot available for an Optional Image Memory module.

Yes Yes

Option

Additional Optional Sorting Image Memory (Minimum 16 MB) is required for the Hard Disk Drive to function. (For Tandem, Remote Copy, etc.)

19 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Items

Description DP-8020E DP-8020P DP-8016P

Features 1 Automatic Features Auto Magnification Selection Auto Paper Selection Auto Paper Tray Selection

Yes

Using ADF only

Yes Yes

Auto Start

Yes

Remote Diagnostic

Yes

Machine Stops when Out of Toner 2 Additional Features Low Level Paper Warning Photo Mode Original Detection Release Edit / Effects Book Mode Edge Mode Margin Mode X-Y Zoom Stamping / Page Numbering Inverse Mode (Negative / Positive) Centering Mode Image Repeat Mirror Mode Others (Inverting ADF & ADU)

Remarks

Yes Empty Only Yes No

Reservation while Power On Initializing. Requires the Fax Communication Board (DA-FG180) option or the Internet Fax / E-MAIL Module (DA-NF180) option. PPC Function

256 steps Manually overridden when using the Original Size keys.

Yes Yes Yes No No No Yes Yes No

2-Page Copy Mode

Yes

2 in 1 4 in 1 6 in 1 8 in 1

Yes Yes No No

Booklet Mode

No

With Digital Sky Shot

LDR → LTR x 2 (A3 → A4 x 2, B4 → B5 x 2)

Copy from four 1-Sided pages to 1 Booklet Mode sheet.

20 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Items Duplex Copy 1→2 2→1 2→2 Book→2 1st Page BLANK 1st Page IMAGE Image Rotation (90 or 270 °) Electronic Sorting Rotation Sorting Insertion Job Cover Mode Page Insertion Mode OHP Interleave Mode Presentation Mode Department Counter ADF Multi Size Feed JOB Build and SADF Mode Original Counter Job Memory Job Time Display Concurrent Copy Tandem Copy Mode Remote Copy Mode Scan Once Print Many Mode Job Complete Notice Trial Copy Mode Weekly Timer Function Mode Interrupt Electronic Counter Digital Sky Shot Mode Double Exposure 3 Control Panel Display Status Lamp

Description DP-8020E DP-8020P DP-8016P Yes

Remarks

No Yes

Yes Yes

Scanning twice by turning the original.

No No

1→2/2→1/2→2 Book → 2

No No Yes Yes Yes No No No No Yes

300 Departments

No Yes No Yes Yes Yes No No

2 Jobs in Memory 12 Concurrent Copy Jobs

Yes Yes

No No No Yes Yes Yes Yes Yes LCD Yes

20 digits x 2 lines GREEN: Scanning / Printing RED: Alarm / Warning

21 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Items Key Original Size Copy Size Keypad Clear Stop Start Energy Saver Multi Size Feed Sort Function Mode Original Detection Release Interrupt Reset One-Touch key Mode Change LCD Main Indication Message Language (Default) Original Size / Image Indication Paper Size / Image Indication Paper Tray Selection Selected Paper Tray / Tray Status Original Mode Selection Copy Density Selection Setting Confirmation Function Classification Zoom Magnification Number of Copies JOB Build and SADF / Multi Size Feed Mode Error Code Finishing Warning Indicators Add Toner Toner Waste Container Full Add Paper (No Paper) Add Paper (Under 50 sheets)

Description DP-8020E DP-8020P DP-8016P

Remarks

Yes Yes Yes Yes Yes Yes Yes No Yes Yes No Yes Yes Yes Yes English (American) Specified Language Yes (without Image) Yes (without Image) Yes

With Keyboard Option Copier / Printer / NW Scanner / Fax and Internet Fax Mode For USA and Canada For EU and Other Destinations

Yes Yes

Text / Text-Photo / Photo

Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes Yes No

22 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Description DP-8020E DP-8020P DP-8016P Paper Jam Indication Yes Paper Jam Location Yes Service Alert Call Yes User Error Yes Machine Error Yes History of Jam Errors Yes 4 Main Unit Total Counter Electronic Yes Items

Mechanical Max. Weight of Documents on the Platen Glass ADF with Document Guide Clip Pocket Operating Instructions Pocket Warning / Caution Label 5 Optical System Original Detection Method Scanning Method Dehumidifier Mechanical Multi Copy Mode 6 Process System Type Toner Toner Waste Container Drum Life Developer Life Dehumidifier Manual Add Toner

Remarks

Standard for EU. Available as a Service Part for Other Destinations.

Yes

11.02 lb (5 kg) Yes Yes No Specified Language Reflective Photo Sensor Type 600 dpi CCD Yes

Supplied as a Service Part

No Separate OPC Unit and Developer Unit Type 10 K 10 K 60 K 60 K Yes Yes

User replacement

Supplied as a Service Part Manually adds toner to the developer (up to TDC threshold)

23 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Items PM Cycle 1 PM Cycle Major PM Minor PM (Cleaning) Packing Configuration

1 Packing Dimension

2 Packing Weight

Description DP-8020E DP-8020P DP-8016P

120 K 60 K 28.5 x 29.7 x 28.6 in (725 x 755 x 726 mm) 29.5 x 31.3 x 29.7 in (750 x 796 x 755 mm) 28.7 x 29.3 x 25.8 in (730 x 745 x 655 mm) 127.77 lb 125.56 lb (58 kg) (57 kg) 143.187 lb 140.98 lb (65 kg) (64 kg) 112.35 lb 110.14 lb (51 kg) (50 kg)

3 Accessories Process Unit Developer Toner Toner Waste Container Operating Instructions Power Supply

Yes No No No Yes

1 Power Requirement

99 - 132 VAC 47 - 63 Hz Single phase 180 - 264 VAC 47 - 63 Hz Single phase

2 Power Consumption Max.Power Consumption 100 VAC PS 220 VAC PS Standby 100 VAC PS 220 VAC PS Energy Saver Power Saver Mode 100 VAC PS 220 VAC PS Sleep Mode 100 VAC PS

Remarks

For USA, Canada For China For EU and Other Destinations For USA and Canada For China For EU and Other Destinations

120 VAC 220 - 240 VAC

Less than 1.3 KW Less than 1.3 KW 120 W 120 W

19.0 W 19.5 W 8.5 W

220 VAC PS

9.5 W

Shutdown Mode 100 VAC PS 220 VAC PS

1.4 W 1.6 W

Turns On the Heater Power. Automatically enters the Sleep or Shutdown Mode after 10 minutes from the Standby or Energy Saver Mode. Manually enters the Energy Saver Mode by pressing the Energy Saver key. Sleep or Shutdown mode is controlled by the General Functions setting. Network Function not available

24 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Items Ambient Conditions 1 Temperature 2 Relative Humidity 3 Safety 4 Energy Saver

5 EMI

6 Lead Free Solder (PbF)

Description DP-8020E DP-8020P DP-8016P 50 - 80 °F / 10 - 30 °C 30 - 80% RH UL60950-1 / CSA C22.2 No.609501 EN60950-1 / IEC60950-1 Energy Star Compliant Class A computing device in FCC Rules Part 15 Class B EN55022, EN55024, EN61000-3-2, EN61000-3-3, CISPR22 This Product uses Lead Free (PbF) PCBs

Remarks

For USA and Canada For EU and Other Destinations For USA and Canada

For EU and Other Destinations

Refer to the Parts Manual for details

25 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

1.3. 1.3.1.

Fax, Printer and Internet Fax Functions Fax Function Items

Main Specifications 1 Compatibility 2 PSTN Line Port 3 Leased Line Port 4 V.24 Line Port 5 Modem Speed 6 Coding Scheme 7 ECM 8 Short Protocol 9 Transmission Speed

Description DP-8020E DP-8020P G3 Yes No No 33.6 - 2.4 kbps JBIG/MMR/MR/MH Yes

Remarks ITU-T Std & Non-Std 1-Line Only

T.30/V.34/V.17/V.29/V.27ter Conforms to ITU-T Rec. T.30 ECM

Yes (B, D) Approx. 2.9 sec

Transmission Std. : 203 x 98 (8 x 3.85) Fine : 203 x 196 (8 x 7.7) S-Fine : 203 x 391 (8 x 15.4) 406 x 391 (16 x 15.4) 10 Communication Resolution 600dpi : 600 x 600 dpi dpi x lpi (pels/mm x lines/ Reception mm) Std. : 203 x 98 (8 x 3.85) Fine : 203 x 196 (8 x 7.7) S-Fine : 203 x 391 (8 x 15.4) 406 x 391 (16 x 15.4) 600dpi : 600 x 600 dpi Scanner Mechanism 1 Scanning Device CCD (ADF / Platen) 2 Scanning Speed (ADF) Resolution Vertical Horizontal Std: 203 x 98 (8 x 3.85) dpi x lpi (pels/mm x lines/ mm) 0.9 / 1.0 sec 0.7 sec Fine: 203 x 196 (8 x 7.7) dpi x lpi (pels/mm x lines/ mm) S-Fine: 406 x 391 (16 x 15.4) dpi x lpi (pels/mm x 1.8 / 2.0 sec 1.4 sec lines/mm) 600dpi: 600 x 600 2.8 sec 2.1 sec 3 Scanning Speed (Platen) Resolution Vertical Horizontal 600dpi: 600 x 600 2.8 sec 2.1 sec Std. : 203 x 98 (8 x 3.85) 4 Scanning Resolution Fine : 203 x 196 (8 x 7.7) dpi x lpi (pel/mm x lines/ S-Fine : 203 x 391 (8 x 15.4) mm) 406 x 391 (16 x 15.4) 600dpi : 600 x 600 dpi

ITU-T Image No. 1 (A4, Std Resolution)

600 dpi communication is only possible between T.30 Compliant Panafax, WORKiO, and other T.30 compliant machines.

LTR / A4, Scanned in Vertical or Horizontal Direction. Excluding Initializing Time and ADF slipping factor.

26 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Items 5 Document Size (Max.) 6 Effective Scanning Width 7 A3 size TX/RX 8 Reduction XMT 9 ADF Capacity 10 Collation Stack Printer Mechanism 1 Recording Method 2 Recording Speed 3 Recording Resolution Fax

Description DP-8020E DP-8020P ADF: LDR / A3 LDR (11.5 in) / A3 (292 mm) Yes Yes 50 sheets Yes LP 23 / 30 ppm (A4 Horizontal) 600 x 600 dpi

4 Recording Paper Size

Ledger / Legal / Letter / A3 / B4 / A4 / A5

5 Effective Printing Width

11.4 in (289 mm)

6 Recording Paper Capacity 7 Collation Stack 8 Consumable

600 sheets Yes Toner Bottle, Developer, OPC Drum

Remarks

Conforms to ITU-T A3 LDR to LTR / A3 to B4 / A3 to A4 / B4 to A4 Face-Up, feed from top page LTR / A4 (20 lb / 75 g/m2) Face Down

Recording Speed attained after the 1st copy. Invoice : Not supported. Ledger size is transmitted as A3 size for N. American models. If A3 is received, approx. 1" of image on both edges are not printed on Ledger size paper. Conforms to ITU-T A3 Optional max. 2250 sheets LTR / A4 : 20 lb (75 g/m2) Face Down

Fax Memory 1 Standard Memory

2 MB (120 pages)

2 Optional Memory

4 MB 8 MB

Dual Operation 1 Multi Task Operation 2 Direct XMT Reserve 3 Memory XMT Reserve 4 Number of Memory Job Files

Flash ROM, ITU-T Image No.1 (A4, Std Resolution) Expansion Flash Memory Card, using ITU-T Image No.1 (A4, Std Resolution)

Yes Yes Yes Yes

Max. 50 files

27 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Items Dialing/Telephone Features 1 One-Touch Keys 2 One-Touch / Program Keys 3 One-Touch Auto Dialers 4 Abbr. Auto Dialers

Description DP-8020E DP-8020P 28 4 32 200

5 Total Auto Dialers

232

6 Directory Search Dialing 7 Max. Tel Number Digits 8 Max. Station Name Characters 9 Full Number Dialing (Buffered Dialing) 10 Direct Dialing (Monitor Dialing)

Yes 36

Requires Optional Keyboard.

Plus an additional 800 stations available to select from, when the optional Hard Disk Drive (DAHD18) is installed.

15 Yes

Max. 50 stations

Yes

Voice mode

11 Automatic Redialing

Yes

12 Manual Redialing

Yes

13 14 15 16 17 18

Yes Yes Yes No Yes No

Line Monitor Speaker Chain Dialing (Hybrid Dial) Pulse / Tone Dialing Pulse to Tone Change Flash Key Handset

Remarks

Up to 15 times at 0 to 15 min. intervals Pressing the REDIAL/PAUSE button In Monitor Dialing mode only 10 pps / DTMF

28 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Items Transmission Features 1 Direct Transmission 2 Memory Transmission 3 Quick Memory Transmission 4 Multi-Station Transmission (Sequential Broadcasting) 5 Direct Deferred Transmission 6 Deferred Transmission 7 Deferred Multi-Station Transmission 8 Priority Direct Transmission 9 Priority Memory Transmission 10 Batch Transmission 11 90 Degree Rotation Transmission 12 Cover Sheet 13 Confidential Mail Box 14 Multi-Copy Transmission 15 Memory Back-Up 16 Duplex Scanning Reception Features 1 Substitute Reception

Description DP-8020E DP-8020P Yes Yes

Remarks

Page Retransmission

Yes Yes

Max. 250 stations

No

ADF Deferred Transmission

Yes

Max. 50 timers

Yes Yes

Priority ADF Transmission

No Yes

Real Time (up to 5 Files)

Yes Yes No No Yes Yes

FAX : Back-up with Flash Memory. Copy / Printer : No Back-up with D-RAM With Inverting ADF (i-ADF)

Yes

2 Fixed Reduction

Yes

3 Auto Reduction

Yes

4 Overlap Printing

Yes

5 Receive to Memory 6 Distinctive Ring Detector (DRD) 7 90 Degree Rotation Reception 8 Duplex Printing

Yes

LTR/A4/LGL: 70 - 100% (in 1% Steps), Top & Left Alignment LTR/A4/LGL: 70 - 100% (in 1% Steps), Top & Left Alignment Page End Approx. 0.51 in (13 mm)

No Yes Yes

29 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Items Polling 1 Polling 2 Turnaround Polling 3 Multi-Station Polling 4 Deferred Polling 5 Deferred Multi-Station Polling 6 Direct Polling Tx 7 Memory Polling Tx 8 Preset Polling Password 9 Temporary Polling Password 10 Continuous Polling Convenience 1 Panel Display 2 Voice Contact 3 Edit File Mode 4 Incomplete File Save 5 Automatic Cover Sheet Certainty 1 Verification Stamp 2 Header / Total Page Print 3 Transaction Journal 4 Comm. Journal 5 Last Ind. XMT Journal List Printouts 1 One-Touch List 2 ABBR. No. List 3 Program List 4 Address Book Search List 5 Fax Parameter List 6 File List 7 Ind. XMT Journal 8 Directory Sheet

Description DP-8020E DP-8020P

Remarks

Yes No Yes Yes

Max. 250 stations Max. 50 timers

Yes

Max. 50 timers / 250 stations

No Yes Yes

1 File

Yes Yes LCD No Yes Yes Yes

With View Mode With View Mode

Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No

200 Transactions / with View Mode With Image Data

Auto Dialer List With View Mode

30 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Items Identifications 1 Logo 2 Multiple Logo 3 Character ID 4 Numeric ID Special Communications 1 Password XMT / RCV 2 Selective Reception 3 Relay XMT Request 4 Relay XMT Center 5 Confidential XMT / Polling 6 Confidential Center 7 Mailbox XMT / Polling 8 Mailbox Center 9 File XMT 10 Fax Forward 11 Sub-Address XMT 12 Sub-address RCV 13 OMR-XMT Others 1 Fax Access Code 2 PIN Code Access 3 Intelligent Redial (AI) 4 Department Code 5 Power Saver Mode 6 Self Diagnostic Function 7 Remote Diagnostic Function 8 Check & Call Function 9 V.24 / Encryption Interface

Description DP-8020E DP-8020P Yes No Yes Yes No No No No No No No No No Yes Yes No No Yes Yes Yes Yes Yes Yes

Remarks 25 Characters 16 Characters 20 Digits

TSI Check

Received File Transfer (Only with Internet Fax Option) T. Routing

For USA and Canada only 5 Files 300 Departmental Codes

Yes Yes No

31 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

1.3.2.

Printer Function Items

Interface 1 Centronics Parallel I/F 2 LAN (Network) 3 USB Port 4 IEEE-1394 Printer Function 1 Printing Size (Paper Tray) 2 Printing Size (Multi-Purpose Tray) 3 Stapling 4 Printing Resolution (dpi) 5 Interface 6 OS 7 Printer Work Memory Size 8 GDI

Description DP-8020E/P DP-8016P No Ethernet 10Base-T/ 100Base-TX Yes No Letter / Legal / Ledger / A3 / A4 / A5 / B4 / B5 / FLS1 / FLS2 / Invoice / 8K / 16K Additionally; Envelope #10 / Envelope DL / Custom Size (PCL / PS only) No 300 x 300 600 x 600 1200 (Equivalent) x 600 (PCL / PS only) USB / Ethernet Win 98 / Me / Win NT 4.0 / Win 2000 / XP / Windows Server 2003 / MAC 8.6-10.4 20 MB Yes

9 PDL (PCL6)

Yes

10 PDL (PS3)

Yes

No

11 Duplex Printing

Yes

No

12 Collation Stack 13 Status Monitor Network USB 14 Network Printing 15 Smoothing 16 Applicable PC 17 Multi-Task Operation Printing while Fax-XMT from Memory Printing while Fax-RCV into Memory Fax-XMT from Memory while Printing Fax-RCV into Memory while Printing

Remarks

USB

8K / 16K = China only

8K / 16K = Tray1 only

MAC 8.6-10.4 is PS only. Not expandable Requires Optional PCL6 Emulation Kit. Requires Optional PS / PCL6 Emulation Kit DP-8020E only. Custom Size/Post Card Size is not available.

Yes Yes No Yes Yes IBM PC, AT or Compatible, MAC

MAC is PS only.

Yes Yes Yes Yes

32 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Items

Description DP-8020E/P DP-8016P

18 Output to separate tray for Printing, Fax, Copy

No

19 Font

Yes

20 Mailbox

Yes

21 Secure Mailbox

Yes

Remarks

Requires Optional PCL6 or PS / PCL6 Emulation Kit Requires Optional HDD Unit. Max. 100 Users. Max. 20 mailboxes for each User ID Requires Optional HDD Unit. Max. 100 Users. Max. 20 mailboxes for each User ID

33 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

1.3.3.

Network Scanner Function Items

Interface 1 Centronics Parallel I/F 2 LAN (Network) 3 USB Port 4 IEEE-1394 Network Scanning Function 1 Scanning Device 2 Scanning Speed (ADF / I-ADF) 3 Halftone 4 Max. Document Size 5 Scanning Resolution (dpi) 6 OS 7 2-Sided Scanning 8 File Format 9 Completion Notice 10 Protocol Network Address Features

Description DP-8020E DP-8020P

Remarks

No Ethernet 10Base-T/ 100Base-TX No No CCD (i-ADF / ADF / Platen) 600 x 600 : 2.1 sec 300 x 300 : 1.1 sec 150 x 150 : 1.1 sec 256 Halftone shades Ledger, A3 600 x 600 300 x 300 150 x 150 Win 98 / Me / Win NT 4.0 / Win 2000 / XP / Windows Server 2003 Yes Mult-page TIFF / PDF Yes

Letter / A4 With Error Diffusion Selectable, 600 dpi Optical Scanner

With i-ADF. TIFF can also be converted to PDF with the PDMS Software Auto Pop-up on the PC Screen (requires Network Status Monitor - installed with PDMS Software)

TCP/IP, Non-Std

1 One Touch Address Keys

32

2 Abbr. Address Numbers

60

Requires Optional Keyboard. Shared with Fax/Internet Fax One Touch Address, 32 in Total Independent for Network Scanner

34 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

1.3.4.

Internet Fax Function Items

Main Specifications 1 Communication Protocols 2 Max. Modem Speed 3 Coding Scheme 4 File Format 5 Line Interface Scanner Mechanism 1 Max. Document Size 2 Effective Scanning Width 3 Scanning Resolution dpi x lpi (pel/mm x lines/mm) Printer Mechanism 1 Printing Resolution 2 Effective Recording Width Transmission Features

Description DP-8020E DP-8020P SMTP / POP3 / MIME NA JBIG/MMR/MR/MH TIFF / PDF RJ-45 Ledger, A3 11.4 in (289 mm) Std. : 203 x 98 (8 x 3.85) Fine : 203 x 196 (8 x 7.7) S-Fine : 203 x 391 (8 x 15.4) 406 x 391 (16 x 15.4) 600dpi : 600 x 600 dpi

Yes

2 Memory Transmission 3 Sequential Multi-Station Transmission

Yes

LAN: 600 dpi, 16 x 15.4 Scanning Resolution is available with Parameter setting

Simultaneous operation of G3 Fax and LAN is available.

Yes Yes

5 Sender Selection 6 G3 / Email Mixed Broadcasting 7 Deferred Transmission

Yes

8 Fax Forward

Yes

9 Sub-address RCV

Yes

10 Mail Header Email Header Print Selection Subject Line

Selectable PDF file is only available if sending to PC (Network Scanner). Ethernet LAN

600 dpi 11.4 in (289 mm)

1 Multi-Task Operation

4 Simultaneous Multi-Station Transmission

Remarks

Max. 250 stations (200 Address Book + 50 Full Number Dialing)

Yes Yes

Yes Random Entry

Received File Transfer, only with Internet Fax Option Inbound Routing, only with Internet Fax Option All or From / To / Subject only

35 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Items

Description DP-8020E DP-8020P

Remarks

LAN Features 1 Internet Fax Communication

Yes

2 Internet Mail Reception 3 Internet Fax Server Features

Yes

4 5 6 7

A3 Communication is available with Parameter setting.

Internet Fax Relay XMT

Yes

Email Relay MXT Received Fax / Email Forward PC to FAX Transmission

Yes

Internet Fax → Internet Fax → G3FAX PC → Internet Fax → G3FAX

Yes

Local print available

Inbound Routing

Yes

Using Sub-Address. Local print available

Yes

Via Email

Phone Book Registration from PC Internet Fax Parameters Registration via Email Internet Delivery Confirmation Network Scanning Network Printing LPR / LPD GDI PDL

No

Yes Yes Yes

With MDN 600 dpi

Yes Yes

600 dpi 600 dpi Requires Optional PCL6 or PS Emulation Kit

Yes

8 DHCP Client

Yes

9 LDAP

Yes

10 TIFF Viewer Certainty 1 Comm. Journal (w / Image) ID 1 Email Address

Yes

Lightweight Directory Access Protocol Selectable, PDMS / TIFF Viewer

Yes Yes

36 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

1.4.

System Combination

ADF

Inverting ADF (DP-8020E only) ADF PC Board

Scanner Unit (SPC PC Board)

Panel (PNL PC Board)

Key Counter Harness Option

Dehumidifier Heater Kit

Expansion Flash Memory Card 4 or 8M

Main PC Board (SC PC Board)

Automatic Duplex Unit (DP-8020E only)

Document Sensor Motor

PCL6 Emulation Option

Fax Communication Option (FXB/MJR)

PS/PCL6 Emulation Option

Printer

Network Scanner Option

USB Interface

Internet Fax/ E-Mail Option

10/100 Ethernet Interface

Electronic Sorting Memory

Image Memory 16, 64, 128MB Either Option

Hard Disk Drive Option

SPC PC Board

2nd Paper Tray (CST2 PC Board)

3rd Paper Tray (CST3 PC Board)

Standard Configuration 4th Paper Tray (CST2 PC Board) Option

37 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

1.5.

Options List

■ Options Option Name Printer Controller Module (PCL) Multi Page Description Language Controller Module (PCL/PostScript) Fax Communication Board Keyboard Option Hard Disk Drive Unit Expansion Board Expansion Flash Memory Card, 4 MB Expansion Flash Memory Card, 8MB Image Memory (16MB) Image Memory (64 MB) Image Memory (128MB) Accounting Software Platen Cover Automatic Document Feeder Inverting Automatic Document Feeder 2nd / 4rd Paper Tray 3rd Paper Tray Deluxe Stand (High) Deluxe Stand (Mid) Deluxe Stand (Low) Stand (1-Paper Tray Configuration) Stand (2-Paper Tray Configuration) Stand (3-Paper Tray Configuration) Stand (4-Paper Tray Configuration) Key Counter Harness Kit

Option Number Remarks DA-PC820 Printer Controller for PCL6* Printer Controller for PCL6/PS3* DA-MC820 For DP-8020E/8020P* only DA-FG180 G3 Fax Communication DA-KB180 Additional Optional Sorting Image Memory (Minimum 16 MB) is required for the Hard DA-HD18 Disk Drive to function. (For additional 800 address book, etc.) DA-EM600 F-ROM Board (8 MB) UE-410047 Additional Memory for Fax / Internet Fax UE-410048 DA-SM16B For Electronic Sorting DA-SM64B DA-SM28B DA-WA10 For Accounting Function DA-UC200 Available in Specified Destinations DA-AS181 DA-AR202 For DP-8020E DA-DS184 4th Paper Tray is for DP-8020E only. DA-DS185 3rd Paper Tray is for DP-8020E only. DA1D18A For USA and Canada Note: DA1D18B The same Deluxe Stand (DA1D18C) is used for either 3 or 4 Paper Tray DA1D18C Configuration. DA-DA188-PE DA-DA189-PE Available in Specified Destinations DA-DA190-PE DA-DA191-PE DA-KH180

Note: 1. PCL6 is a Page Description Language of the Hewlett-Packard Company. 2. PS3 is a Page Description Language of the Adobe Systems Company. 3. Availability may differ as per destination. Please ask your sales company for details. ■ Supplies Part Name Toner OPC Drum Developer

Part Number DQ-TUJ10K-PU DQ-TUJ10K-PK DQ-TU10J-PB DQ-H60J DQ-Z60J

Remarks For PU (USA/Canada, etc.), 10K For China, 10K For EU and Other Destinations, 10K 60K 60K

Note: Availability may differ as per destination. Please ask your sales company for details.

38 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

2 Maintenance, Adjustments and Check Points 2.1.

Preventive Maintenance Preventive maintenance is performed at specific intervals, and consists of machine cleaning, and parts replacement. It is essential to perform these service activities properly, and at the specified intervals for customer satisfaction. The purpose of this service is to maintain machine performance, and image quality. - You should prepare the replacement parts, and cleaning tools beforehand. - After completing the preventive maintenance, discard the used parts, and packaging in accordance with local regulations, and clean the surrounding area. - Before servicing the equipment, turn the power switches Off, and disconnect the power cord from the wall outlet. - Before using solvents such as IPA (Isopropyl alcohol), put on rubber gloves, and wear eye protection. 1

Timing - Perform the preventive maintenance in accordance with the Preventive Maintenance Check List (refer to 2.4)

2

Cleaning the Rollers - Rollers should be cleaned with water, and a soft cloth. - Use the IPA (Isopropyl Alcohol) sparingly.

3

Disassembly and Adjustment Precautions CAUTION! Turn the Power Switch on the Right Side of the machine to the OFF position, and then unplug the AC Power Cord from the wall outlet before disassembling the machine. (During a Lightning Storm, to prevent electrocution disconnect the Telephone Line Cable first before unplugging the AC Power Cord.) - After taking the unit apart, do not attempt to operate the machine. - When operating the machine with covers removed, be careful, and avoid clothing from being caught by moving components. - While the electricity is applied to the unit, do not connect nor disconnect the connectors on any PC Board. - When handling the drum, follow the precautions listed in section 2.3. - Ensure to use correct screws. - Use toothed lock washers for the installation of ground wires to ensure electrical continuity. - To reassemble, reverse the sequence of disassembly, unless otherwise specified. - Blown fuses should only be replaced with fuses of the same specified rating.

39 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

4

Laser Handling Precautions The optical laser system employed by this photocopier is completely sealed by a protective housing, and an external cover. Therefore, the laser beam will not stray or leak during photocopying operation. However, when servicing the photocopier, take the following precautions: 1. Do not insert any screwdrivers, or other tools that have high reflective properties into the laser's path. 2. .Before servicing the machine, remove watches, rings, or other metallic objects that you may be wearing. (This is to avoid the danger of the laser striking the eye by reflecting off the metallic objects being worn.) Since the laser beam cannot be seen with the naked eye, for maximum safety, please follow the above precautions.

40 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

2.2.

Required Tools

No. Tools 1 Soft Cloth 2 Isopropyl Alcohol 3 Phillips Screwdriver (#2) 4

Stubby Phillips Screwdriver (#2)

5

Slotted Screwdriver (3/32 in)

6

Tweezer

2.2.1.

Preventive Maintenance Method

1

Memory Data

Important Action Check

2

Auto Document Feeder (ADF)

Check & Clean

3

Scanner Unit

4

Transmitter Unit

5

Mirrors

Check & Clean Check & Clean Check & Clean

6

Inspection Items

7

Gears, Rollers Shafts Check & Grease Timing Belts Check & Clean

No.

8

No. Tools 7 Pliers 8 Cotton Swab 9 Brush KS-660 - Conductive Grease 10 (Available from Shin-Etsu Silicones of America, Inc. URL: http://www.shinetsusilicones.com) Molykote EM-50L Grease 11 (Available from Dow Corning, URL: http://www.dowcorning.com)

Part Description

Check

Comments 1. Print the RAM DATA for reference, and as a precaution. 2. After completing the task(s), print, and compare the RAM DATA with the previously printed one. 1. Clean the Rollers, and Separation Rubber with a Wet soft cloth (Water). Note: For stubborn toner accumulation, wipe with a soft cloth saturated with Isopropyl Alcohol first, then follow up with a soft cloth saturated with water. 1. Clean the Scanning Glass, or White Reference Sheet with Isopropyl Alcohol when required. 1. Remove any foreign obstacles. 2. Clean the Rollers with a Wet soft cloth (Water). 1. Do not touch the surface of the Mirrors with your hands. 2. Clean any dirt, or fingerprints with a Dry Cotton Swab. Note: Do not use any type of Alcohol. 1. Check the Harnesses. 2. Check the Connectors. 3. Check the Screws. If required, replace consumable parts. 1. Check, and grease the required Gears, and Shafts. 1. Check for belt looseness, or abrasion. 2. Adjust the Idle Pulley.

41 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

2.3.

Preventive Maintenance Points 3 4 5

1

i-ADF

2

8 11 9 10 6

ADF

12

16

7 15 13 14 43 42 37, 39 36, 38, 41 40 27 26

44

DETAIL A

27 45

25 22

20

17 18, 19 23, 24 21 20 17 18, 19 21 20 17 18, 19 21 20 17 18, 19

42 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

29

30

31

28 35 32, 33, 34

DETAIL A

43 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

2.4.

Preventive Maintenance Check List

The chart outlined below is a general guideline for maintenance.

No.

Mechanical Parts

Ref. No.

Cleaning Cycle Method (Sheet)

Replacement/Adjustment Cycle Procedure (Sheet)

Ref. Counter

i-ADF Unit 1

ADF Roller

2314

60K

Water 1

120K

2

Pre Feed Roller

2018

60K

Water 1

120K

3

Separation Roller

2509

60K

Water 1

120K

4

Torque Limiter Bushing 2510

60K

Water 1

120K

5

Torque Limiter Spring

2511

60K

Water 1

120K

Refer to 2.2.1.of the Service Manual

F7-08

Refer to 2.2.2.of the Service Manual

F7-08

Refer to 2.2.4.of the Service Manual

F7-04

ADF Unit 6

Exit 1 Roller

1812

60K

Water 1

-

7

White Sheet

1814

60K

Water 1

-

8

Feed Roller

2010

60K

Water 1

-

9

Pre Feed Roller

2018

60K

120K

2024

-

Water 1 1

120K

10 Separation Rubber 11

Paper Feed Roller

60K

2001

60K

12 Scanning Pad 1822 Scanner Unit 13 Mirror 1 415 14 Mirror 2 421 15 Platen (L) Glass 106 16 Scanning (S) Glass 110 2nd, 3rd & 4th Paper Trays

60K

Water Dry soft cloth

60K 60K 60K 60K

-

17 Pickup Roller

619

60K

Water 1

120K

18 Separation Roller

629

60K

120K

19 Torque Limiter 1

690

-

Water 1 1

120K

-

120K

20 Feed Roller

623

60K

Water

21 Intermediate Roller

3104

60K

Water 1

-

22 Feed Roller

689

60K

Water 1

120K

23 Separation Roller

658

60K

120K

24 Torque Limiter 2 25 Registration Roller Bias Transfer Unit 26 Bias Transfer Roller (BTR)

691 601

60K

Water 1 -

711

60K

Dry soft cloth

120K

27 Duplex Feed Roller

735

60K

Water 1

Process Unit Developer

-

-

-

1403

-

-

Refer to F7-12/-13/2.2.10.of the 14/-15 Service Manual

Sheet Bypass

-

28 OPC Drum

120K -

-

60K 60K

Refer to 2.2.9.of the Service Manual

F7-11

Refer to 2.2.8.of the Service Manual

F7-02

Refer to 2.2.5.of the Service Manual

F7-10 F7-06

44 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Mechanical Parts

Ref. No.

29 Charge Corona Case 30 Charge Wire

1444 1443

31 32 33 34 35

1408 1410 1411 1412 1415

No.

Cleaning Blade Front Cleaning Felt Rear Cleaning Felt Cleaning Sponge Splash Prevention Sheet Fuser Unit

Cleaning Cycle Method (Sheet) 60K 10K By Customer -

Replacement/Adjustment Ref. Cycle Counter Procedure (Sheet) Refer to F7-07 2.2.5.of the 60K Service Manual 60K 60K 60K 60K 60K

36 Fuser Roller

1115

60K

Water 1

120K

37 Pressure Roller

1021

60K

240K

38 Fuser Roller Bushing 39 Pressure Roller Bushing 40 Thermistor Assembly 41 Fuser Lamp 42 Separator

1114 1020

-

Water 1 -

120K 240K

1125

60K

Dry soft cloth

120K

1116 1109

60K

Dry soft cloth

240K 120K

43 Exit 2 Roller

1104

60K

Water 1

Main Unit 44 Ozone Filter

825

-

-

240K

45 Toner Spill Tray

1202

60K

-

-

Refer to 2.2.6.of the Service Manual

F7-02

Refer to F7-02 2.2.13.of the Service Manual

Note: 1. Wet Cloth represents a soft cloth saturated with water. For stubborn toner accumulation, wipe with a soft cloth saturated with Isopropyl Alcohol first, then follow up with a soft cloth saturated with water. 2. The Maintenance Cycle is based on the Counter Information for each individual module. To verify the counter information, print the Total Counter List using the Service Mode: F7 - Electronic Counter - 00 (List Print). 3. Cleaning, Replacement, and Adjustment Cycle (Sheet) are based on using Panasonic's recommended standard paper, and supplies. These cycles may vary with the kind of paper used, Paper size, orientation, print duty, continuous/interval print, and/or ambient conditions. • Total Counter View Mode on the LCD The Total Counter can be displayed on the Panel Display by pressing "COPY SIZE", and "PAPER TRAY" keys simultaneously in Standby mode for quick reference.

TOTAL COUNTER 1234 • LCD Display Brightness Adjustment To adjust the brightness of the LCD display, press and while holding down the "CLEAR" key, keep pressing the "ORIGINAL SIZE", or the "COPY SIZE" key until the desired brightness is achieved. ORIGINAL SIZE: Dimmer COPY SIZE : Brighter 45 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

2.5.

Resetting the P/M (Preventive Maintenance) Counter

When the machine reaches the preset P/M Cycle, it will show "Call for P/M", or "Replace The Toner Waste Container" on the LCD Display. The PM Counter can be reset by following the procedures below.

2.5.1.

"Call for P/M" (Default: 120K)

1. Perform the P/M (Preventive Maintenance). Refer to Section 2.3, and 2.4. 2. Press “FUNCTION”, “ORIGINAL SIZE”, and “3” keys sequentially to enter the Service Mode. 3. Enter the Copy Service Mode F5-70 (PM Cycle), and change to the desired value. 4. Press “FUNCTION”, and “CLEAR” keys simultaneously to exit the Service Mode.

2.5.2.

"Call for P/M ADF" (Default: Not Set)

1. Perform the P/M (Preventive Maintenance). Refer to Section 2.3, and 2.4. 2. Press “FUNCTION”, “ORIGINAL SIZE”, and “3” keys sequentially to enter the Service Mode. 3. Enter the Copy Service Mode F5-87 (ADF PM Cycle), and change to the desired value. 4. Press “FUNCTION”, and “CLEAR” keys simultaneously to exit the Service Mode.

2.5.3.

U14 "Replace The Toner Waste Container"

A. Blinking Maintenance, and Toner Waste Container Indicators Upon detecting that the Toner Waste Container is full, the machine will complete the current job, and stop operating. A blinking Maintenance, and Toner Waste Container Indicators will appear on the display. To continue using the machine temporarily while waiting for the Service Technician, press any key (up to 100 additional copies can be made). B. Steady Maintenance, and Toner Waste Container Indicators Upon reaching the 100 copies, the machine stops, and will not allow further operation until the Toner Waste Container is replaced. Replace the Toner Waste Container. (Refer to Section 2.2.5.of the Service Manual)

46 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

2.6.

Lubrication Point List

This information is used for routine Preventive Maintenance (PM) calls to ensure the highest degree of reliability. Inspect the following areas, and lubricate as required. The inspection interval is usually 120K copies, or more, however the interval may be reduced due to environmental conditions. Ref. No. Automatic Duplex Unit Mechanical Parts

Pinch Timing Roller

Grease

Lubrication Point

712

KS-660 Bias Transfer Bushing

709

47 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

2.7.

Updating the Firmware

The Quickest, and Most Easiest Method of Updating the Firmware is to use the Network Firmware Tool (FUP) using Ethernet LAN Port, and a Crossover Cable. The Network FUP Tool version must be 3.XX, or higher, and it can be found on the Panasonic Document Management System CD-ROM included with the main unit, or on the CD-ROM included with the PCL, or PS/PCL options. Refer to the Firmware Update Operation Instructions, Service Notes (8.1.) for additional details.

2.7.1.

Firmware Configuration

A. Hardware Configuration This machine is controlled by two (2) CPUs which are located on the System Control (SC) PC Board, and the Scanner Printer Control (SPC) PC Board.

SC PC Board

Standard Configuration On Board

PC Ethernet Port

F-ROM CPU

4 MB

(A) (1) Program

With PCL Option Configuration (B) (2) Program

With PS Option Configuration (D) (5) Program

4 MB

4 MB

4 MB

PC USB Port

Slot 1 FRM PCB 8 MB

Flash Memory Card 4 MB or 8 MB

(C) 8MB (3) Program 2 MB (a)

(E) 8MB (6) Program (a) 4 MB

(4)

(7) Font 4 MB

(b)

Font 4 MB

(b)

Slot 2

Not Used

SPC PC Board F-ROM CPU

512 KB

Scanner Control Program Printer Control Program

B. SC PC Board Firmware The 4 MB Program Memory (F-ROM) is integrated on the SC PCB. An Optional Expansion 8 MB Program Memory (FRM8 PCB) can be installed into SLOT 1. The Firmware to be written into the 4 MB onboard, and the 8 MB of SLOT 1 depends upon the configuration of the Standard, PCL, or PS Options. (1) Standard The Standard Program (1) is only written into the 4 MB onboard, which is assigned as ROM Code (A). (2) For PCL Option The PCL Control Program (2) must be written into the 4 MB onboard, which is assigned as ROM Code (B). The PCL Control Program (3), and PCL Font data (4) are written into the 8 MB in the SLOT 1. The Firmware (3), and (4) are assigned as ROM Code (C). When using 8 MB Flash Memory Card, the 8 MB Program (C) can be written onto one card.

48 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

When using 4 MB Flash Memory Card, the 8 MB program (C) must be divided onto 2 cards, one 4 MB card for the PCL Control Program (3), and one 4 MB card for the PCL Font data (4). (3) For PS Option The PS Control Program must be written into the 4 MB onboard, which is assigned as ROM Code (D). The PS Control Program (6), and (7) are written into the 8 MB in the SLOT 1. Both Firmwares (6), and (7) are assigned as ROM Code (E). When using 4 MB Flash Memory Card, the 8 MB program (E) must be divided onto 2 cards, one 4 MB card for the PS Control Program (6), and one 4 MB card for the PS Control Program (7). C. SPC PC Board Firmware The 512 KB Program Memory (F-ROM) is integrated on the SPC PCB. The Programs for Scanner Control, and Printer Control are saved on the Board. The Firmware is transferred as Serial Data from the SC PCB. D. Firmware Updating Ports Three (3) types of Ports are available for updating the firmware. (1) Ethernet LAN Port (The Quickest, and Most Easiest Method) The machine's Firmware can be updated from a PC via Local Area Network (LAN). Refer to the Firmware Update Operation Instructions, Service Notes (8.1.) for additional details. (2) USB Port (Alternate) The machine's Firmware can be updated from a PC via USB Port. The Master Firmware Card can also be created from a PC using the USB Port. Refer to the Firmware Update Operation Instructions, Service Notes (8.1.) for additional details. (3) Flash Memory Card (Alternate) The machine's Firmware can be updated using the Master Firmware Card. The Master Firmware Card can be created by copying the Firmware from an existing machine's SC PCB using a 4 MB, or 8 MB Flash Memory Card. To update the SC, SPC, and PNL PCB, 3 Flash Memory Cards are required for the Standard configuration, or 5 Flash Memory Cards for the PCL, or PS/PCL configuration.

2.7.2.

Updating through a LAN Port (The Quickest, and Most Easiest Method)

The firmware code can be easily updated when the main unit is connected to a LAN. The Network Firmware Update Tool can also be used by connecting to the machine using a crossover cable, if the unit is not connected to a LAN. 1) Install the Network Firmware Update Tool to your PC The option CD-ROM includes the Network Firmware Update Tool, and the Main Unit Firmware Code. Please refer to the following Operating Instructions to install the Network Firmware Update Tool. The installation password is "workio". Operating Instructions: \xFirmware\Tools\NwFirmup\NwFirmup OI.pdf (Refer to the NW Firmware Update Tool OI on the CD) Setup: \xFirmware\Tools\NwFirmup\Setup\Setup.exe 2) Preparing the Firmware Code Double click the appropriate Destination Shortcut Batch File, and copy the Firmware Code File on the CD-ROM to the Firmware Data Folder in your PC. Note that the files in the Archive will be extracted automatically into the designated folder when the Archived file (.exe) is Double-clicked.

49 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Example: From: Destination Shortcut Batch File: D:(CD-ROM Drive) \ xFirmware \ USA.bat Firmware Code File: DP-8016_8020_PU_xxxxxx.exe To: Firmware Data Folder: C:\ Panasonic \ Panasonic-FUP \ Data 3) Preparing the Main Unit for the Firmware Upgrade Make sure the unit's Key Operator Password is the same as the tool's password. Make sure the unit is in an idle state (e.g. not making copies, not printing, etc.). 4) Upgrading the Main Unit's Firmware Code Start the Network Firmware Update Tool, and select the following Firmware Code Folders in the C:\Panasonic\Panasonic-FUP\Data folder, and then follow the display instructions to upgrade the Main Unit's Firmware Codes. Parent Firmware File Folder \ DP-8016_8020_PU_xxxxxx

Sub Firmware File Folder

\ SC_STD \ DP-LL80AxVxxxxx_xx \ SC_PCL \ DP-LL80BxVxxxxx_xx \ SC_PS \ DP-LL80DxVxxxxx_xx \ SPC \ LL80-SPCAxVxxxxxx

Transferring Order 1 1 1 2

When you select the Parent Folder, the following Firmware Type window appears. Proper Sub File Folders are selected automatically by selecting the Firmware Type. The transferring order is set up automatically.

Note: 1. Manual mode must be used, when updating the designated version of the firmware, or changing the type of the firmware. Please refer to the Section 2.2, "Setting up the Network Firmware Update Tool, File Selection Tab" of the Operating Instructions. 2. While updating the firmware code, the display may become garbled, however, it will return to normal upon completion of the firmware update. 3. If the firmware update fails, and the unit does not boot up, the Network Firmware Update Tool will not be able to transfer the firmware code. If this occurs, please refer to the next section "Updating through the USB Port", and use the Local Firmware Update Tool to recover the unit. 4. The suffix "_xx" for the Folder Name, or File Name may not exist depending on the destination location.

2.7.3.

Updating through the USB Port (Alternate Method)

If the device is not connected to the LAN, upgrade the firmware code using the USB Port. 1) Install the Local Firmware Update Tool to your PC The option CD-ROM includes the Local Firmware Update Tool, and the Main Unit Firmware Code. Please refer to the following Operating Instructions to install the Local Firmware Update Tool. Operating Instructions: \xFirmware\Tools\Firmup\FIRMUP OI.pdf (Refer to the Local Firmware Update Tool OI on the CD) Setup: \xFirmware\Tools\Firmup\Setup\Setup.exe 50 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

2) Preparing the Firmware Code Double click the appropriate Destination Shortcut Batch File, and copy the Firmware Code File on the CD-ROM to the Firmware Data Folder in your PC. Note that the files in the Archive will be extracted automatically into the designated folder when the Archived file (.exe) is Double-clicked. Example: From: Destination Shortcut Batch File: D:(CD-ROM Drive) \ xFirmware \ USA.bat Firmware Code File: DP-8016_8020_PU_xxxxxx.exe To: Firmware Data Folder: C:\ Panasonic \ Panasonic-FUP \ Data 3) Preparing the Main Unit for the Firmware Upgrade Important: DO NOT connect the USB Cable yet. Enter into Test Mode F9-07-01 to enable the unit to accept the programming code from the USB Port. Now connect the USB Cable between the Unit, and PC. 4) Upgrading the Main Unit's Firmware Code Start the Local Firmware Update Tool, and select the following Firmware Code Parent File Folder in the C:\Panasonic\Panasonic-FUP\Data folder, and select the Firmware Code Type then follow the display instructions to upgrade the Main Unit's Firmware Codes. You must process each firmware file separately in this manner, and sequence. Parent Firmware File Folder \ DP-8016_8020_PU_xxxxxx

Sub Firmware File Folder

Firmware File

\ SC_STD \ DP-LL80AxVxxxxx_xx DP-LL80AxVxxxxx_xx.bin \ SC_PCL \ DP-LL80BxVxxxxx_xx DP-LL80BxVxxxxx_xx.bin \ SC_PS \ DP-LL80DxVxxxxx_xx \ SPC \ LL80-SPCAxVxxxxxx

DP-LL80CxVxxxxxa_xx.bin DP-LL80CxVxxxxxb.bin DP-LL80DxVxxxxx_xx.bin DP-LL80ExVxxxxxa_xx.bin DP-LL80ExVxxxxxb.bin LL80-SPCAxVxxxxxx.bin

Transferring Order 1 1-1 1-2 1-3 1-1 1-2 1-3 2

When you select the Parent Folder, the following Firmware Type window appears. Proper Firmware Files are selected automatically by selecting the Firmware Type. The transferring order is set up automatically.

Note: 1. While updating the firmware code, the display may become garbled, however, it will return to normal upon completion of the firmware update. 2. Please refer to the service manual for additional details. 3. The suffix "_xx" for the Folder Name, or File Name may not exist depending on the destination location.

51 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

2.7.4.

Updating the Firmware using the Master Firmware Card (Alternate method)

1. Before starting, print the F5/F6 Parameters List (Copy Service Mode F9-03-00). 2. Turn the Power Switch on the Right side of the machine to the OFF position. (During a Lightning Storm, to prevent electrocution disconnect the Telephone Line Cable first before unplugging the AC Power Cord, if the Fax Option is installed.) 3. Install the appropriate Master Firmware Card into the machine. 4. Turn the Power Switch on the Right Side of the machine to the ON position. 5. Press “FUNCTION”, “ORIGINAL SIZE” keys, and then Key “3” on the keypad sequentially. 6. Perform the Copy Service Mode F9-07-00 (Update From Master Card). 7. The firmware is copied into the machine. 8. After the update is completed, the machine reboots itself, and returns to standby. 9. Turn the Power Switch on the Right side of the machine to the OFF position. 10. Remove the Master Firmware Card from the machine. 11. Turn the Power Switch on the Right Side of the machine to the ON position. 12. Reprogram the F5 & F6 Parameters according to the lists printed in Step 1 above if the settings are other than factory default. Note: After the update is completed, the machine reboots itself, and returns to standby mode. Repeat the above steps if there are additional firmware code files to be updated. Confirm that the update was successfully completed by checking the Firmware Version with F9 Parameters F9-02-xx. Caution: If the unit does not boot up properly in step 8, refer to Service Manual 3.7.8. (Firmware Emergency Recovery) 3.7.4.1. Creating a Master Firmware Card A. Utilizing the Firmware Update Kit 1) Install the Local Firmware Update Tool to your PC The option CD-ROM includes the Local Firmware Update Tool, and the Main Unit Firmware Code. Please refer to the following Operating Instructions to install the Local Firmware Update Tool. Operating Instructions: \xFirmware\Tools\Firmup\FIRMUP OI.pdf (Refer to the Local Firmware Update Tool OI on the CD) Setup: \xFirmware\Tools\Firmup\Setup\Setup.exe 2) Preparing the Firmware Code Double click the appropriate Destination Shortcut Batch File, and copy the Firmware Code File on the CD-ROM to the Firmware Data Folder in your PC. Note that the files in the Archive will be extracted automatically into the designated folder when the Archived file (.exe) is Double-clicked. Example: From: Destination Shortcut Batch File: D:(CD-ROM Drive) \ xFirmware \ USA.bat Firmware Code File: DP-8016_8020_PU_xxxxxx.exe To: Firmware Data Folder: C:\ Panasonic \ Panasonic-FUP \ Data 3) Preparing the Main Unit for the Programming Master Firmware Card Important: DO NOT connect the USB Cable yet. 1. Turn the Power Switch on the Right side of the machine to the OFF position. (During a Lightning Storm, to prevent electrocution disconnect the Telephone Line Cable first before unplugging the AC Power Cord, if the Fax Option is installed.) 2. Insert/Remove the Flash Memory Card (4 MB, or 8 MB) into/from the machine. 52 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

3. Turn the Power Switch on the Right Side of the machine to the ON position. 4. Press “FUNCTION”, “ORIGINAL SIZE” keys, and then Key “3” on the keypad sequentially. 5. Perform the Update Program Card Mode F9-09 (Update Program Card). The unit is now ready to accept the firmware code from the USB Port. Now connect the USB Cable between the Unit, and PC. (Refer to the Local Firmware Update Tool OI on the CD) Repeat the above steps if there are additional master firmware cards to be programmed. B. Copying the Firmware from an Existing Machine using a Flash Memory Card (4 MB, or 8 MB) 1. Turn the Power Switch on the Right side of the machine to the OFF position. (During a Lightning Storm, to prevent electrocution disconnect the Telephone Line Cable first before unplugging the AC Power Cord, if the Fax Option is installed.) 2. Install a Flash Memory Card (4 MB, or 8 MB) into the machine. 3. Turn the Power Switch on the Right Side of the machine to the ON position. 4. Press “FUNCTION”, “ORIGINAL SIZE” keys, and then Key “3” on the keypad sequentially. 5. Perform the Copy Service Mode F9-08 (Program Backup). 6. The firmware is copied into the Flash Memory Card. 7. After the backup is completed, press "STOP" first, and then press "FUNCTION" + "CLEAR" keys simultaneously to return to standby. 8. Turn the Power Switch on the Right side of the machine to the OFF position. 9. Remove the Master Firmware Card that you just created from the machine. 10. Turn the Power Switch on the Right Side of the machine to the ON position. 11. Use this Master Firmware Card to update the firmware on other machines. 3.7.4.2. Erasing the Master Firmware Card 1. Turn the Power Switch on the Right side of the machine to the OFF position. (During a Lightning Storm, to prevent electrocution disconnect the Telephone Line Cable first before unplugging the AC Power Cord, if the Fax Option is installed.) 2. Install the Master Firmware Card into the machine. 3. Turn the Power Switch on the Right Side of the machine to the ON position. 4. Press “FUNCTION”, “ORIGINAL SIZE” keys, and then Key “3” on the keypad sequentially. 5. Perform the Service Mode F9-09 (Update Program Card). 6. After the Flash Memory Card is erased, machine prompts “READY TO PROGRAM PRESS SET TO START”. Press “STOP”. 7. Press "STOP" first, and then press "FUNCTION" + "CLEAR" keys simultaneously to return to standby. 8. Turn the Power Switch on the Right side of the machine to the OFF position. 9. Remove the blank Flash Memory Card from the machine. 10. Repeat from Step 2 above if you are erasing another Master Firmware Card.

53 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

2.7.5.

User Authentication Function Confirmation (Specified Destinations only)

If your customer requires User Authentication, and/or Via Fax Server, setup the feature(s) by referring to the Operating Instructions (For User Authentication).

2.7.6.

Notice after installing the HDD option

After the Hard Disk Drive Unit is installed, to prevent a Scan Disk Function from being performed (similar to Windows OS when the power is abruptly interrupted), it is important to follow the step sequence below when turning OFF the Power Switch on the machine. 1. If the machine is in the "ENERGY SAVER (Shutdown Mode)", you may turn the Power Switch on the Right Side of the machine to the OFF position. If it is not in the "ENERGY SAVER (Shutdown Mode)", continue to step 2 below. 2. Press "FUNCTION", and "ENERGY SAVER" keys simultaneously first. 3. Wait approximately 10 seconds while the machine writes the closing status onto the Hard Disk Drive Unit, and advances into “ENERGY SAVER MODE”. 4. Turn the Power Switch on the Right side of the machine to the OFF position. 5. Unplug the AC Power Cord. (During a Lightning Storm, to prevent electrocution disconnect the Telephone Line Cable first before unplugging the AC Power Cord, if the Fax option installed.) 6. After finishing the installation of the Hard Disk Drive, please go over the above Power Down procedure with the customer to avoid the Scan Disk Function from being performed (indicated by SCANNING HARD DISK message on the display), and customer inquiries related to abrupt Power Off. 7. Reconnect the Telephone Line Cable if it was disconnected.

2.7.7.

Firmware Emergency Recovery

The easiest method to recover the firmware in an Emergency Recovery routine is to either use the Local Firmware Update Tool software by selecting the Independent File method, or using the Master Firmware Flash Card method (2 Flash Cards required). Whichever method you select, it is easier to restore the machine's firmware to the Standard (AAV) Type first as it only requires 2 files to bring the machine to initial working condition. (Install the files in this order: SC, and SPC). After recovering, if optional PCL, or PS/PCL firmware is required, use the Network Firmware Update Tool, or the Local Firmware Update Tool to update the firmware to the required level. If the unit does not boot up properly, follow the steps below: 1. Turn the power Off (use the power switch on the right side of the unit). - Before proceeding to the next step, you must prepare either the Local Firmware Update Tool, or create the Master Firmware Flash Cards (read the appropriate sections first). - If using the Master Firmware Card, insert the Master Firmware Flash Cards in the unit. 2. Turn the power On while holding the “ENERGY SAVER” key. 3. When the green lamp on the front panel turns On, release the “ENERGY SAVER” key. - If using the Master Firmware Card, the unit will start updating the Firmware code files automatically. The unit is now ready to accept the firmware code from the USB Port, or Master Firmware Card. Repeat the above steps if there are additional firmware code files to be updated.

54 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

2.7.8.

Firmware Version SC

:

DP-LL80 A A Vxxxxx (a) PU (AU) Destination Code (Fax) AU : USA/Canada AB : UK Destination Code (Copier) PU : USA/Canada PB : UK Division Soft (When it is divided into (a) and (b)) Firmware Version (V1xxxx) Language Code A : A-English, C-French & Spanish c : French, German, Italian, Dutch, Portuguese, Spanish, English & Greek d : French, German, Swedish, Norwegian, Danish, Finnish, Turkish & English e : French, German, English, Polish, Hungarian, Czech & Russian j : English & Korean k : English & Taiwanese n : English & Chinese Firmware Type A : Standard B, C, D, E : Optional Model Number

SPC

:

LL80- SPC

A A Vxxxxx Firmware Version (V1xxxx) AA: Fixed SPC

Model Number

55 Ver. 1.0

OCT 2006

Ver. 1.0

Part Item

OPC Drum & Developer

Corona Wire Process Unit

Toner Density Sensor

LSU SC PC Board

10 11

12

13 14

Installation Main Cleaning Optics Process Unit Toner Spill Tray Replace Scanning Lamp Platen Glass OPC Drum Developer

Work

9

1 2 3 4 5 6 7 8

No.

1

1

2 2 1

1

2

1

Toner Spill Tray Clean

1

1

1

Process Optics Unit Clean Clean

1

2

3

3

4

1

2

3

4 1

2

3 4

5

5 2

3

4 5

6

LSU Image PWM OPC Print LSU PWM Density TDC Adj. Counter Pattern F5/F6 Adj. F6-49 Adj. Adj. F6-39 (Note 4) (Note 1) Reset Print /50/51 F8-09 (Note 3) F8-14 F8-18 (Note 2) 4 3 1 2 3 2 3 2 2 3 2 2 1 5 4 3 2 3 1

Input F5/F6 Parameter

Replace Developer

Remark

2.8.

Adjustment

When the following items are replaced or cleaned, perform adjustments in the correct order.

DP-8020E/8020P/8016P

Copy Quality Adjustment Procedure (Order)

56

OCT 2006

DP-8020E/8020P/8016P

Note: 1. Print F5/F6 1) Press “FUNCTION”, “ORIGINAL SIZE”, and “3” keys sequentially to enter the Service Mode. 2) Press the "9" key to enter the F9 Mode (Unit Maintenance). 3) Press the "START" key. 4) Press "3", and "SET" keys. 5) Press "V", or "/\" arrow keys to select "00 F5/F6 PARAMETERS", and press "SET" key. 6) Prints the memory contents of the F5, and F6 modes. 2. Contrast Adjusting 1) Press “FUNCTION”, “ORIGINAL SIZE”, and “3” keys sequentially to enter the Service Mode. 2) Press the "2", and the "START" keys to enter the F2 Mode (Single Copy Test). 3) Set the exposure to the center position. 4) Set the machine to TEXT / PHOTO Mode. 5) Make a copy of Test Chart 53/54 with gray scale (P/N: FQ-SJ1011), and compare the density to the chart shown below. If it is within specification, skip to step (14). a. Gray scale “A” should not be visible. b. Gray scale “2” should be clearly visible. A

. . . . . . . . . . .. . . . . . 1 . . . 2

Not visible (Not visible, or hardly visible) Clearly visible

3

6) Press the "STOP" key to exit the F2 Mode (Single Copy Test). 7) Press the “6”, and the "START" keys to enter the F6 Mode (Adjust Parameters). 8) Enter F6-50 Mode (T/P Mode Image Density). 9) Press the "SET" key to highlight the current value. 10) Enter a new value (up to 3-digits). Note: The “RESET” key is used to change to a Negative, or Positive (+/-) value. (+) : Lighter (-) : Darker 11) Press the “SET”, and “STOP” keys. 12) Enter F2 Mode (Single Copy Test). 13) Make a copy to confirm the adjustment. Note: Repeat Steps (3) to (10) until desired density is attained. F6-49 : T Mode Image Density (Text) F6-51 : P Mode Image Density (Photo) 14) Press “FUNCTION”, and “CLEAR” keys simultaneously to exit the Service Mode.

57 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

3. PWM Adjustment 1) Ensure that Ledger / A3 Size Paper is loaded in one of the Trays, and pull out the remaining trays (including the bypass tray) to disable them. 2) Press “FUNCTION”, “ORIGINAL SIZE”, and “3” keys sequentially to enter the Service Mode. 3) Press the "8" key to enter the F8 Mode (Service Adjustment). 4) Press the "START" key. 5) Press the "1", "8", and "SET" keys sequentially to enter the F8-18 "C18 PRT PWM ADJ. PTN.". 6) Press the "START" key to begin the LSU PWM Pattern Printing. Sample: 4 gray patches are visible in the illustration, the value of the uppermost patch position is "+2" in our example.

(-5)

(0) +2

(+5)

In our sample, 4 patches are visible. Test Pattern

7) Press the "STOP" key. 8) Press the "6", and the "START" keys to enter the F6 Mode (Adjust Parameters). 9) Select "39 LSU Unit PWM ADJUST". 10) Press "SET" button, and enter the value of the gray patch, as established in Step (6). 4. LSU Adjustment Refer to 2.9.

58 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

2.9.

Adjusting the Printer Registration, LSU Image Side to Side

When installing the Paper Tray option, the following LSU Image Side to Side adjustment must be performed. The Printer registration is adjusted at the factory. If copy image is abnormal, specially in the Rotation Copy mode, adjust it by the following procedure.

2.9.1.

Printer Registration

1. Insert Ledger, or A3 size paper into the 1st tray, and change the tray setting to the appropriate paper size. Empty, or pull out all the remaining trays (including the bypass tray) to disable them. 2. Press “FUNCTION”, “ORIGINAL SIZE” keys, and then Key “3” on the keypad sequentially. 3. Perform the Service Mode F1-03 (Print Test Pattern 1). 4. Check the gap of the print pattern from the paper edge, refer to the Figure below. 5. Perform the Service Mode F6-04 (Printer Registration) to adjust the gap to be 5 mm. 6. If the gap is less than 5 mm, input a (-) value. If more than 5 mm, input a (+) value. 7. Press "STOP" first, and then press "FUNCTION" + "CLEAR" keys simultaneously to return to standby. Two lines are printed on the top (Lead edge). For Ledger or A3, place as Portrait. For Letter or A4, place as Landscape. 5 mm Top (Lead edge) Two lines are printed

5 mm

5 mm

Two lines are printed

2.9.2.

LSU Image Side to Side Adjustment for the Tray

1. Insert paper into the 1st tray, and change the tray setting to the appropriate paper size. Empty, or pull out all the remaining trays (including the bypass tray) to disable them. 2. Press “FUNCTION”, “ORIGINAL SIZE” keys, and then Key “3” on the keypad sequentially. 3. Perform the Service Mode F1-03 (Print Test Pattern 1). 4. Check the gap of the print pattern from the paper edge, refer to the Figure above. 5. Perform the Service Mode F6-10 to F6-14, to adjust the gap to be 5 mm. 6. If the gap is less than 5 mm, input a (+) value. If more than 5 mm, input a (-) value. 7. Proceed the above steps for other Tray. 8. Press "STOP" first, and then press "FUNCTION" + "CLEAR" keys simultaneously to return to standby.

59 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

2.9.3.

LSU Image Side to Side Adjustment for the ADU

1. Insert paper into the 1st tray, and change the tray setting to the appropriate paper size. Empty, or pull out all the remaining trays (including the bypass tray) to disable them. 2. Press “FUNCTION”, “ORIGINAL SIZE” keys, and then Key “3” on the keypad sequentially. 3. Perform the Service Mode F1-06 (Print Test Pattern 4). 4. Check the gap of the print pattern from the paper edge, refer to the Figure above. 5. Perform the Service Mode F6-16 (ADU Side Adjust), to adjust the gap to be 5 mm. 6. If the gap is less than 5 mm, input a (+) value. If more than 5 mm, input a (-) value. 7. Press "STOP" first, and then press "FUNCTION" + "CLEAR" keys simultaneously to return to standby.

2.9.4.

100% Read Adjustment

1. Place the Original Document on the Platen Scanner. 2. Insert Ledger, or A3 size paper into the 1st tray, and change the tray setting to the appropriate paper size. Empty, or pull out all the remaining trays (including the bypass tray) to disable them. 3. Press “FUNCTION”, “ORIGINAL SIZE” keys, and then Key “3” on the keypad sequentially. 4. Perform the Service Mode F2 (Single Copy Test). 5. Check the Image size of the Copy, and the Original as Portrait. 6. Perform the Service Mode F6-00 (Adj 100% Side-Side Read), to adjust for an identical vertical (side-to-side) size ratio. 7. If the image is smaller than the Original, input a (+) value. If bigger than the Original, input a (-) value. 8. Perform the Service Mode F6-01 (Adj 100% Lead-Tail Read), to adjust for an identical horizontal (top-to-bottom) size ratio. 9. If the image is smaller than the Original, input a (+) value. If bigger than the Original, input a (-) value. 10. Press "STOP" first, and then press "FUNCTION" + "CLEAR" keys simultaneously to return to standby. Note: This is for size adjustment, and does not adjust positioning.

2.9.5.

Original Registration & CCD Read Adjustments

1. Place the Original Document on the Platen Scanner. 2. Insert Ledger, or A3 size paper into the 1st tray, and change the tray setting to the appropriate paper size. Empty, or pull out all the remaining trays (including the bypass tray) to disable them. 3. Press “FUNCTION”, “ORIGINAL SIZE” keys, and then Key “3” on the keypad sequentially. 4. Perform the Service Mode F2 (Single Copy Test). 5. Check the Image size of the Copy, and the Original as Portrait. 6. Perform the Service Mode F6-03 (Original Registration), to adjust the platen original registration detection timing. 7. If the gap is smaller than the Original, input a (-) value. If bigger than the Original, input a (+) value. 8. Perform the Service Mode F6-53 (CCD Read Position Adj), to adjust the CCD Read side position. 9. If the gap is smaller than the Original, input a (+) value. If bigger than the Original, input a (-) value. 10. Press "STOP" first, and then press "FUNCTION" + "CLEAR" keys simultaneously to return to standby.

60 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

2.9.6.

ADF 100% Image 1-Sided Adjustment

1. Place the Original Document on the ADF. 2. Insert Ledger, or A3 size paper into the 1st tray, and change the tray setting to the appropriate paper size. Empty, or pull out all the remaining trays (including the bypass tray) to disable them. 3. Press “FUNCTION”, “ORIGINAL SIZE” keys, and then Key “3” on the keypad sequentially. 4. Perform the Service Mode F2 (Single Copy Test). 5. Check the Image size of the Copy, and the Original as Portrait. 6. Perform the Service Mode F6-93 (ADF 100% Image 1-Sided), to adjust for an identical vertical (side-to-side) magnification for 1-sided scan. 7. If the image is smaller than the Original, input a (+) value. If bigger than the Original, input a (-) value. 8. Press "STOP" first, and then press "FUNCTION" + "CLEAR" keys simultaneously to return to standby. Note: This is for size adjustment, and does not adjust positioning.

2.9.7.

ADF Original Read Edge & ADF Main Scan Adjustments

1. Place the Original Document on the ADF. 2. Insert Ledger, or A3 size paper into the 1st tray, and change the tray setting to the appropriate paper size. Empty, or pull out all the remaining trays (including the bypass tray) to disable them. 3. Press “FUNCTION”, “ORIGINAL SIZE” keys, and then Key “3” on the keypad sequentially. 4. Perform the Service Mode F2 (Single Copy Test). 5. Check the Image size of the Copy, and the Original as Portrait. 6. Perform the Service Mode F6-91 (Original Read Edge ADF), to adjust for the ADF Original Read Edge detection timing. 7. If the gap is less than the Original, input a (+) value. If bigger than the Original, input a (-) value. 8. Perform the Service Mode F6-90 (ADF Read Main Scan Pos.), to adjust for the ADF horizontal image read start position. 9. If the gap is less than the Original, input a (+) value. If bigger than the Original, input a (-) value. 10. Press "STOP" first, and then press "FUNCTION" + "CLEAR" keys simultaneously to return to standby.

61 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

2.9.8.

Double Exposure Lead, and Side Edge Adjustments

Caution: Confirm that the Scanning Pad is installed, and aligned correctly on the ADF/i-ADF prior to making any adjustments. (Refer to the ADF/i-ADF Installation Instructions in Sect. 8.11., or 8.12.of the Service Manual)

Driver's License

1. Place a Business Card, Driver's License, Insurance Card, etc. (Invoice size, or smaller) on the Platen Glass as illustrated.

Platen

2. Insert Letter, or A4 size paper into the 1st Paper Tray, or onto the Sheet Bypass, and change the tray settings to the appropriate paper size. 3. Make a copy using the Double Exposure Copy Mode. 4. Check the Copy Image. a. For a Horizontal Black Line in the Center, adjust the Service Mode F6-63 (Lead Edge Read Timing) by following the steps below. b. For a Vertical Black Line at the Leading Edge, adjust the Service Mode F6-64 (Side Edge Read Adjust) by following the steps below. Output of Letter (A4) Paper (not LTR-R) Driver's License

Driver's License Adjust with F6-63

Driver's License

Driver's License

Adjust with F6-64

5. Press “FUNCTION”, “ORIGINAL SIZE” keys, and then Key “3” on the keypad sequentially. 6. Perform the Service Mode F6-63 (Lead Edge Read Timing), and F6-64 (Side Edge Read Adjust). Note: It is not recommended setting the value higher than "4" as it will increase the Void Area. 7. Press "STOP" first, and then press "FUNCTION" + "CLEAR" keys simultaneously to return to standby. 8. Repeat the above steps 3 to 7 until the Black Line(s) disappear.

62 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

2.10. Signal Waveform 2.10.1. Glossary of Electrical Abbreviations

Signal Name +12V +24V +24VD1 +24VFL +24VM +24VOPC +24VOPF +3.3V +5v +5VD +5VP +ACT +ALM +DAT +SLP AC(L) AC(N) ACSW ADF2 ADF3 ADF4 AGND BAT+ BMCNT BTHP BZBZ+ C1C1+ C2C2+ C3+ C4+ CASET CCRMT CPWM CSB1 CST2 CST3 CST4 CSTOP CSTOP4

Glossary of Electrical Abbreviations Function +12 VDC Power Supply +24 VDC Power Supply +24 VDC Power Supply +20 / +24 VDC Power Supply +24 VDC Power Supply +24 VDC Power Supply +24 VDC Power Supply +3.3 VDC Power Supply +5 VDC Power Supply +5 VDC Power Supply +5 VDC Power Supply ACTIVE Lamp LED Power Supply ALARM Lamp LED Power Supply DATA Lamp LED Power Supply Energy Saver Lamp LED Power Supply AC Power Supply AC Power Supply Fuser Relay 2nd Paper Tray Feed Roller Drive Signal 3rd Paper Tray Feed Roller Drive Signal 4th Paper Tray Feed Roller Drive Signal Ground Lithium Battery Toner Bottle Motor Control Signal Toner Bottle Position Sensor Signal Buzzer Signal Buzzer Signal (+) Capacitor 1 Negative Connection Pin for Converter Capacitor 1 Positive Connection Pin for Converter Capacitor 2 Negative Connection Pin for Converter Capacitor 2 Positive Connection Pin for Converter Capacitor 3 Positive Connection Pin for Converter Capacitor 4 Positive Connection Pin for Converter Paper Tray Detection Signal (1st Feeder) Charge Leak Detection Signal Charge Control DC ON/OFF PWM Chip Select Signal 2nd Paper Tray Detection Signal 3rd Paper Tray Detection Signal 4th Paper Tray Detection Signal 2nd Paper Feed Module Detection Signal 4th Paper Feed Module Detection Signal

63 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Signal Name DAA1 DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 DDCPWM E_RDB ELPCNT F/R FDPCHK2 FDPCHK3 FDPCHK4 FSH GND GPWM HFSOL HPMB HSYNC HUMISN HVAC1 HVAC2 IICSCL IICSDA IOUTA IOUTB JAMDOR2 JAMDOR3 JAMDOR4 KCDET KCNT KIN0 KIN1 KIN2 KIN3 KIN4 KIN5 KIN6 KIN7 L1 L2 L5V LD

Glossary of Electrical Abbreviations Function ADF Motor Current Control Signal Data Signal Data Signal Data Signal Data Signal Data Signal Data Signal Data Signal Data Signal Development Control DC ON/OFF PWM Read/Write Execution Control Signal Discharge Lamp Direction of Rotation Signal 2nd Paper Tray Paper Registration Detection Signal 3rd Paper Tray Paper Registration Detection Signal 4th Paper Tray Paper Registration Detection Signal Transfer Gate Clock Ground Grid Control ON/OFF PWM Temp Humidity Sensor Signal LCD driver Power Control Signal Horizontal Synchronous Signal Temp Humidity Sensor Signal INV PC Board/Lamp Signal INV PC Board/Lamp Signal IIC Transmission Clock IIC Transmission Signal Motor Control Signal Motor Control Signal 2nd Paper Tray Jam Access Cover Open Detection Signal 3rd Paper Tray Jam Access Cover Open Detection Signal 4th Paper Tray Jam Access Cover Open Detection Signal Key Counter Option Detection Key Counter Option PNL Key Signal (Key Line) PNL Key Signal (Key Line) PNL Key Signal (Key Line) PNL Key Signal (Key Line) PNL Key Signal (Key Line) PNL Key Signal (Key Line) PNL Key Signal (Key Line) PNL Key Signal (Key Line) Line Signal Line Signal Laser Circuit +5VDC Power Supply Motor Lock Detection Signal 64

Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Signal Name LDBTHP LDCST2 LDCST3 LDCSTSEN LDDUX LDEN LDFPCHK2 LDFPCHK3 LDFPCHK4 LDHEX LDHFPE LDILDI+ LDJAM2 LDJAM3 LDJAM4 LDORI LDPED LDPHK2 LDPHK3 LDPHK4 LDPSEN LDRRSEN LDSSN LDTF LDUPL2 LDUPL3 LDUPL4 LDUPLSEN LDWTB LED0 LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 LED9 LEDCT0 LEDCT1 LEDCT2 LEDCT3 LEDCT4 LIFT1

Glossary of Electrical Abbreviations Function Toner Bottle HP Sensor Signal Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Laser Control Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Laser Diode Control Laser Diode Control + Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage PNL LED Control Signal PNL LED Control Signal PNL LED Control Signal PNL LED Control Signal PNL LED Control Signal PNL LED Control Signal PNL LED Control Signal PNL LED Control Signal PNL LED Control Signal PNL LED Control Signal PNL LED Control Signal PNL LED Control Signal PNL LED Control Signal PNL LED Control Signal PNL LED Control Signal 1st Paper Tray Lift Motor Signal 65

Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Signal Name LIFT2 LIFT4 LIFTM2 LIFTM4 MGND MRCLH2 MRCLH3 MRCLH4 N.C. nA3SEN nA5SEN nAA3S nAA3SN nAADL1 nAADL2 nAAPNT nAB1SN nAB2SN nAB4S nAB4SN nACLH1 nACLH2 nACLH3 nACLOCKAD1 nAEJC nAKEEP1 nAKEEP2 nANG nAOAC nAPACHG nAPICR nAREV nASTAMP nASTROAD1 nATT nB4SEN nBDOOR nCCLH1 nCCLH2 nCCLH3 nCST2 nCTCNT nCTON nDADFON nDUPACK nDUPSEN

Glossary of Electrical Abbreviations Function 2nd Paper Tray Lift Motor Signal 4th Paper Tray Lift Motor Signal 2nd Paper Tray Lift Motor Drive Signal 4th Paper Tray Lift Motor Drive Signal Ground 2nd Paper Tray Intermediate Roller Clutch Drive Signal 3rd Paper Tray Intermediate Roller Clutch Drive Signal 4th Paper Tray Intermediate Roller Clutch Drive Signal No Connection Sheet Bypass Paper Size Detection Signal Sheet Bypass Paper Size Detection Signal Original Width Detection Signal Original Width Detection Signal Original Length Detection Signal Original Length Detection Signal Original Detection Signal Read Point Detection Signal Duplex Eject Detection Signal Original Width Detection Signal Original Width Detection Signal Feed 2 Roller Clutch Control Signal Paper Feed Roller Clutch Control Signal Inverting Roller Clutch Control Signal ADF Motor Control Clock Signal Original Eject Detection Signal Reversing 1 Guide Solenoid Control Signal Reversing 1 Guide Solenoid Control Signal Platen Cover Angle ADF Cover Open Detection Signal Release Lever Plate Solenoid Control Signal Release Lever Plate Solenoid Control Signal ADF Exit Cover Open Detection Signal Stamp Control Signal ADF Motor Control Strobe Signal Attention Signal Sheet Bypass B4 Paper Detection Signal Platen Cover Open Detection Signal Feed 2 Roller Clutch Control Signal ADF Roller Clutch Control Signal Inverting Roller Clutch Control Signal 2nd Paper Tray Detection Signal Counter Drive Signal Ring Detection Signal ADF Option Detection Signal Duplex Print Acknowledge Signal ADU Sensor Signal 66

Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Signal Name nDUREQ nDUXSOL nFLON nFNRDT nFNRDTP nHEXSEN nHFPESEN nHKOF nLEDACT nLEDALM nLEDDAT nLEDSLP nLIFTM3 nLPOW1 nLPOW2 nMMCK nMMON nMMRDY nOPDUP nOPT nORI nOUTA nOUTB nPACK nPCHK4 nPEDSEN nPHY1 nPHY2 nPHYCP nPHYR nPNLRST nPRDY nPRGDWN nPVSYNC nSACK nSADFON nSCNWUP nSLPKY nSREQ nSTAMP nTFSEN nVCNT nVRDY nWAKE nWTBSEN OP3CLK

Glossary of Electrical Abbreviations Function Duplex Print Request ADU Solenoid Control Signal Inverter Ground Fan Ready Signal PS Fan Ready Signal Paper Exit Sensor Signal Bypass Feed Sensor Signal External Phone Off-Hook Detection Signal ACTIVE Lamp LED Control Signal ALARM Lamp LED Control Signal DATA Lamp LED Control Signal Energy Saver Lamp LED Control Signal 3rd Paper Tray Lift Motor Drive Signal Power Control Power Control Main Motor Clock Main Motor Rotation Control Signal Main Motor Ready Signal Duplex Unit Detection Signal PNL4 Detection Home Position Detection Signal Motor Control Signal Motor Control Signal Printer ACK Signal 4th Paper Tray Paper Detection Signal Sheet Bypass Paper Detection Signal CCD CLOCK CCD CLOCK CCD CLOCK CCD CLOCK Panel Reset Signal Printer Ready Signal F-ROM Rewrite Print Registration Scan ACK Signal ADF Detection Signal Energy Saver Signal Energy Saver Key Signal Scanner Request Signal Stamp Control Signal Toner Waste Sensor +24 VDC Power Supply Control Signal VSYNC Reset Signal FAX Wake Up Signal Toner Waste Container Detection Sensor Signal 3rd Paper Tray Motor Clock 67

Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Signal Name OP3ENB OP3FCK OP3FDIN OP3FLD OP3FLT OP3FOT OP3RST OUTA OUTB P/S pADATA1A pADATA1B pBDA PCHK1 PCHK2 PCHK3 PCHK4 pCMLD PFCLCNT PMCK PMON PMRDY PNLRXD PNLTXD POWCNTV pPHY1 pPHY2 pPHYCP pPHYR PS pSENTIM pSPCRST pSPKOT pVREQ RESETB RETRACE RRCLCNT RS RSEN RW_WRB S/H SCN0 SCN1 SCN10 SCN11 SCN2

Glossary of Electrical Abbreviations Function Option Feed FIFO Enable Option Feed FIFO Clock Option Feed FIFO Input Option Feed FIFO Load Option Feed FIFO Latch Option Feed FIFO Output Option Feed FIFO Reset Motor Control Signal Motor Control Signal Motor Start/Stop ADF Motor Control Signal ADF Motor Control Signal Print BDA Signal 1st Paper Tray Paper Detection Signal 2nd Paper Tray Paper Detection Signal 3rd Paper Tray Paper Detection Signal 4th Paper Tray Paper Detection Signal Line Switching Relay Drive Signal Paper Feed Clutch Drive Signal Polygon Motor Clock Polygon Motor Rotation Signal Polygon Motor Ready Signal PNL Reception Data Signal PNL Transmission Data Signal Laser Power Control Signal CCD CLOCK CCD CLOCK CCD CLOCK CCD CLOCK Parallel / Serial Data Input Select Signal Scanner LSYNC Signal SPC Reset Signal Line Dial Tone Signal Print ACK Request Signal LCD Driver Reset Signal Laser Control Registration Roller Drive Signal Register Selection Control Signal Registration Sensor Signal LCD Control Signal Sample Hold Signal PNL Key Signal (Scan Line) PNL Key Signal (Scan Line) PNL Key Signal (Scan Line) PNL Key Signal (Scan Line) PNL Key Signal (Scan Line) 68

Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Signal Name SCN3 SCN4 SCN5 SCN6 SCN8 SCN9 SMCNT SPCRXD SPCTXD SSR TC TDREF TDSEN TEMPSN THERM1 THERM2 TPWM UPLIMIT UPLIMIT2 UPLIMIT3 UPLIMIT4 UPLMT2 UPLMT4 V0 V1 V2 V3 V4 VCL VDD VOUT VOUT1 VOUT2 VSS ZCRS

Glossary of Electrical Abbreviations Function PNL Key Signal (Scan Line) PNL Key Signal (Scan Line) PNL Key Signal (Scan Line) PNL Key Signal (Scan Line) PNL Key Signal (Scan Line) PNL Key Signal (Scan Line) Toner Motor Control Signal SPC Reception Data Signal SPC Transmission Data Signal Heater Control Signal Transfer Control Cleaning Output Toner Density Reference Sensor Toner Density Sensor Signal Temp Humidity Sensor Signal Thermistor Output Signal Ground Transfer Control Transfer Output 1st Paper Tray Paper Level Signal 2nd Paper Tray Paper Level Signal 3rd Paper Tray Paper Level Signal 4th Paper Tray Paper Level Signal 2nd Paper Tray Paper Level Signal 4th Paper Tray Paper Level Signal LCD Driver Supply Voltages LCD Driver Supply Voltages LCD Driver Supply Voltages LCD Driver Supply Voltages LCD Driver Supply Voltages LCD Power Supply +3.3 VDC Power Supply Voltage Converter Input / Output Graphic Data Output Graphic Data Output Ground Heater Control Signal

69 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

2.10.2. SC PC Board CN51 SC PCB Pin No. CN51-1

+24V

PS PCB CN11-1

CN51-2

GND

PS PCB CN11-2

Signal Name

Destination

Signal Waveform

Function

+24V

+24 VDC Power Supply

Ground

0V CN51-3

+5VP

PS PCB CN11-3

+5V

+5 VDC Power Supply

CN51-4

+5VD

PS PCB CN11-4

+5V

+5 VDC Power Supply

CN51-5

+5v

PS PCB CN11-5

+5V

+5 VDC Power Supply

CN51-6

GND

PS PCB CN11-6

Ground

0V CN51-7

GND

Ground

PS PCB CN11-7

0V CN51-8

GND

PS PCB CN11-8

Ground

0V CN51-9

GND

PS PCB CN11-9

Ground

0V CN51-10

GND

Ground

PS PCB CN11-10

0V CN51-11

+3.3V

PS PCB CN11-11

+3.3V

+3.3 VDC Power Supply

CN51-12

+3.3V

PS PCB CN11-12

+3.3V

+3.3 VDC Power Supply

70 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

SC PCB Pin No. CN51-13

Signal Name nLPOW1

Destination

Signal Waveform

PS PCB CN11-13

Function

+24V

Power Control

0V CN51-14

nLPOW2

PS PCB CN11-14

+3.3V

Power Control

0V CN51-15

nVCNT

PS PCB CN11-15

+24V

+24 VDC Power Supply Control Signal

0V CN52 SC PCB Pin No. CN52-1

+24V

PNL1 PCB CN220-1

CN52-2

GND

PNL1 PCB CN220-2

Signal Name

Destination

Signal Waveform

Function

+24V

+24 VDC Power Supply

Ground

0V CN52-3

GND

PNL1 PCB CN220-3

Ground

0V CN52-4

GND

PNL1 PCB CN220-4

Ground

0V CN52-5

+5VP

PNL1 PCB CN220-5

+5V

+5 VDC Power Supply

CN52-6

+5v

PNL1 PCB CN220-6

+5V

+5 VDC Power Supply

CN52-7

PNLRXD

PNL1 PCB CN220-7

+5V

PNL Reception Data Signal

0V CN52-8

PNLTXD

PNL1 PCB CN220-8

+5V

PNL Transmission Data Signal

0V

71 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

SC PCB Pin No. CN52-9

Signal Name nPNLRST

Destination

Signal Waveform

PNL1 PCB CN220-9

+3.3V RESET

CN52-10

nLPOW2

Function

PNL1 PCB CN220-10

Panel Reset Signal

0V +3.3V

Power Control

0V CN52-11

nLPOW1

PNL1 PCB CN220-11

+24V

Power Control

0V CN52-12

nSLPKY

PNL1 PCB CN220-12

+3.3V PRESSED

CN52-13

nWAKE

PNL1 PCB CN220-13

Energy Saver Key Signal

0V

+3.3V

FAX Wake Up Signal

0V CN52-16

nVCNT

PNL1 PCB CN220-16

+24V

+24 VDC Power Supply Control Signal

0V CN53 SC PCB Pin No. CN53-1

Signal Name nPRDY

Destination

Signal Waveform

SPC PCB CN717-1

+5V READY

CN53-2

nVRDY

Function

SPC PCB CN717-2

Printer Ready Signal

0V +5V

VSYNC Reset Signal

0V CN53-3

nPACK

SPC PCB CN717-3

+5V

Printer ACK Signal

0V CN53-4

nATT

SPC PCB CN717-4

+5V

Attention Signal

0V

72 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

SC PCB Pin No. CN53-5

Signal Name nDUPACK

Destination

Signal Waveform

SPC PCB CN717-5

Function

+5V

Duplex Print Acknowledge Signal

0V CN53-6

pBDA

SPC PCB CN717-6

Print BDA Signal

+3.3V 0V

CN53-7

pVREQ

SPC PCB CN717-7

+5V

Print ACK Request Signal

0V CN53-8

nSACK

SPC PCB CN717-8

+5V

Scan ACK Signal

0V CN53-9

nPVSYNC

SPC PCB CN717-9

+5V

Print Registration

0V CN53-10

nDUREQ

SPC PCB CN717-10

+5V

Duplex Print Request

0V CN53-11

pSENTIM

SPC PCB CN717-11

+5V

Scanner LSYNC Signal

0V CN53-12

nSREQ

SPC PCB CN717-12

+5V

Scanner Request Signal

0V CN53-13

pSPCRST

SPC PCB CN717-13

+5V

SPC Reset Signal

0V CN53-14

nPRGDWN

SPC PCB CN717-14

+5V

F-ROM Rewrite

0V CN53-15

GND

SPC PCB CN717-15

Ground

0V CN53-16

GND

Ground

SPC PCB CN717-16

0V

73 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

SC PCB Pin No. CN53-17

Signal Name IICSCL

Destination

Signal Waveform

SPC PCB CN717-17

Function

+5V

IIC Transmission Clock

0V CN53-18

IICSDA

SPC PCB CN717-18

+5V

IIC Transmission Signal

0V CN53-19

GND

SPC PCB CN717-19

Ground

0V CN53-20

nSCNWUP

SPC PCB CN717-20

+5V

Energy Saver Signal

0V CN53-21

SPCRXD

SPC PCB CN717-21

+5V

SPC Reception Data Signal

0V CN53-22

SPCTXD

SPC PCB CN717-22

+5V

SPC Transmission Data Signal

0V CN55 SC PCB Pin No. CN55-1

Signal Name VOUT2

Destination CCD CN850-1

Signal Waveform

Function Graphic Data Output

4 6V 1V

0V CN55-2

AGND

CCD CN850-2

Ground

0V CN55-3

VOUT1

CCD CN850-3

Graphic Data Output

4 6V 1V

0V CN55-4

AGND

CCD CN850-4

Ground

0V CN55-5

AGND

CCD CN850-5

Ground

0V

74 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

SC PCB Pin No. CN55-6

Signal Name AGND

Destination

Signal Waveform

Function

CCD CN850-6

Ground

0V CN55-7

+12V

CCD CN850-7

CN55-8

AGND

CCD CN850-8

+12V

+12 VDC Power Supply

Ground

0V CN55-9

GND

CCD CN850-9

Ground

0V CN55-10

GND

CCD CN850-10

Ground

0V CN55-11

pPHYCP

CCD CN850-11

+3.3V

CCD CLOCK

0V CN55-12

nPHYCP

CCD CN850-12

+3.3V

CCD CLOCK

0V CN55-13

pPHYR

CCD CN850-13

+3.3V

CCD CLOCK

0V CN55-14

nPHYR

CCD CN850-14

+3.3V

CCD CLOCK

0V CN55-15

pPHY2

CCD CN850-15

+3.3V

CCD CLOCK

0V CN55-16

nPHY2

CCD CN850-16

+3.3V

CCD CLOCK

0V CN55-17

pPHY1

CCD CN850-17

+3.3V

CCD CLOCK

0V 75 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

SC PCB Pin No. CN55-18

Signal Name nPHY1

Destination CCD CN850-18

Signal Waveform

Function CCD CLOCK

+3.3V 0V

CN55-19

FSH

CCD CN850-19

Transfer Gate Clock

+3.3V 0V

CN55-20

+5v

CCD CN850-20

+5V

+5 VDC Power Supply

CN57 SC PCB Pin No. CN57-1

+3.3V

LSU CN2-1

CN57-2

GND

LSU CN2-2

Signal Name

Destination

Signal Waveform

Function

+3.3V

+3.3 VDC Power Supply

Ground

0V CN57-3

LDI+

LSU CN2-3

+3.3V

Laser Diode Control +

0V CN57-4

LDI-

LSU CN2-4

+3.3V

Laser Diode Control -

0V

76 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

2.10.3. SPC PC Board CN650 SPC PCB Signal Name Destination Pin No. CN650-1 +5VP ADF PCB CN21-1

CN650-2

MGND

Signal Waveform

Function

+5V

ADF PCB CN21-2

+5 VDC Power Supply

Ground

0V CN650-3

GND

ADF PCB CN21-3

Ground

0V CN650-4

+24V

ADF PCB CN21-4

CN650-5

nAAPNT

ADF PCB CN21-5

+24V

Original Detection Signal

+5V DETECT

CN650-6

N.C.

ADF PCB CN21-6

CN650-7

nAB4SN

ADF PCB CN21-7

+24 VDC Power Supply

0V No Connection

Original Width Detection Signal

+5V 0V

CN650-8

nAA3SN

ADF PCB CN21-8

Original Width Detection Signal

+5V 0V

CN650-9

nAADL1

ADF PCB CN21-9

Original Length Detection Signal

+5V 0V

CN650-10 nAADL2

ADF PCB CN21-10

Original Length Detection Signal

+5V 0V

CN650-11 nAB2SN

ADF PCB CN21-11

Duplex Eject Detection Signal

+5V 0V

77 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

SPC PCB Signal Name Destination Pin No. CN650-12 nAB1SN ADF PCB CN21-12

Signal Waveform

Function Read Point Detection Signal

+5V 0V

CN650-13 nAEJC

ADF PCB CN21-13

Original Eject Detection Signal

+5V 0V

CN650-14 nAREV

ADF PCB CN21-14

ADF Exit Cover Open Detection Signal

+5V OPEN

CN650-15 nAOAC

ADF PCB CN21-15

ADF Cover Open Detection Signal

+5V OPEN

CN650-16 nAKEEP1

ADF PCB CN21-16

0V

0V Reversing 1 Guide Solenoid Control Signal

+5V 0V

CN650-17 nAKEEP2

ADF PCB CN21-17

Reversing 1 Guide Solenoid Control Signal

+5V 0V

CN650-18 nAPACHG

ADF PCB CN21-18

Release Lever Plate Solenoid Control Signal

+5V 0V

CN650-19 nAPICR

ADF PCB CN21-19

Release Lever Plate Solenoid Control Signal

+5V 0V

CN650-20 nSTAMP

ADF PCB CN21-20

Stamp Control Signal

+5V 0V

CN650-21 nACLH1

ADF PCB CN21-21

Feed 2 Roller Clutch Control Signal

+5V 0V

CN650-22 nACLH2

ADF PCB CN21-22

Paper Feed Roller Clutch Control Signal

+5V 0V

78 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

SPC PCB Signal Name Destination Pin No. CN650-23 nACLH3 ADF PCB CN21-23

Signal Waveform

Function Inverting Roller Clutch Control Signal

+5V 0V

CN650-24 nACLOCKA D1

ADF PCB CN21-24

ADF Motor Control Clock +5V Signal

0V CN650-25 nASTROAD1 ADF PCB CN21-25

ADF Motor Control Strobe Signal

+5V 0V

CN650-26 pADATA1A

ADF PCB CN21-26

ADF Motor Control Signal

+5V 0V

CN650-27 pADATA1B

ADF PCB CN21-27

ADF Motor Control Signal

+5V 0V

CN650-28 +24V

ADF PCB CN21-28

CN650-29 GND

ADF PCB CN21-29

+24V

+24 VDC Power Supply

Ground

0V CN650-30 +24V

ADF PCB CN21-30

CN650-31 GND

ADF PCB CN21-31

+24V

+24 VDC Power Supply

Ground

0V CN650-32 DAA1

ADF PCB CN21-32

+5V

ADF Motor Current Control Signal

0V CN650-33 MGND

Ground

ADF PCB CN21-33

0V CN650-34 MGND

Ground

ADF PCB CN21-34

0V

79 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

SPC PCB Signal Name Destination Pin No. CN650-35 nSADFON ADF PCB CN21-35

CN650-36 nDADFON

ADF PCB CN21-36

Signal Waveform

Function

+5V (For i-ADF) +0V (For ADF)

ADF Detection Signal

ADF Option Detection Signal

+5V 0V

CN650-37 +24V

ADF PCB CN21-37

CN650-38 MGND

ADF PCB CN21-38

+24V

+24 VDC Power Supply

Ground

0V CN650-39 +5v

ADF PCB CN21-39

+5V

+5 VDC Power Supply

CN650-40 +5v

ADF PCB CN21-40

+5V

+5 VDC Power Supply

CN655 SPC PCB Signal Name Destination Pin No. CN655-1 OUTA Scanning Motor -1

Signal Waveform

Function Motor Control Signal

+18V 0V

CN655-3

nOUTA

Scanning Motor -2

Motor Control Signal

+18V 0V

CN655-2

+24V

Scanning Motor -3

CN655-4

OUTB

Scanning Motor -4

+24V

+24 VDC Power Supply

Motor Control Signal

+18V 0V

CN655-5

+24V

Scanning Motor -5

+24V

+24 VDC Power Supply

80 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

SPC PCB Signal Name Destination Pin No. CN655-6 nOUTB Scanning Motor -6

Signal Waveform

Function Motor Control Signal

+18V 0V

CN656 SPC PCB Signal Name Destination Pin No. CN656-1 +24V INV PCB CN1-1

CN656-2

+24V

INV PCB CN1-2

CN656-3

nFLON

INV PCB CN1-3

Signal Waveform

Function

+24V

+24 VDC Power Supply

+24V

+24 VDC Power Supply

Inverter Ground

+24V 0V

CN656-4

MGND

INV PCB CN1-4

Ground

0V CN656-5

MGND

INV PCB CN1-5

Ground

0V CN657 SPC PCB Signal Name Destination Pin No. CN657-1 +5VP SNS PCB -1

CN657-2

nANG

SNS PCB -2

Signal Waveform

+5V

GND

+5 VDC Power Supply

Platen Cover Angle

+5V ON

CN657-3

Function

0V

SNS PCB -3

Ground

0V CN657-4

nBDOOR

SNS PCB -4

Platen Cover Open Detection Signal

+5V ON

0V

81 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

SPC PCB Signal Name Destination Pin No. CN657-5 nORI Home Position Sensor -1 CN657-6

CN657-7

GND

LDORI

Signal Waveform

Function Home Position Detection Signal

+5V HOME

0V

Home Position Sensor -2

Ground

0V

Home Position Sensor -3

+1.2V

Photo Sensor DC Drive Voltage

CN701 SPC PCB Signal Name Destination Pin No. CN701-1 L5V LSU CN1-1

CN701-2

GND

Signal Waveform

Function

+5V

LSU CN1-2

Laser Circuit +5VDC Power Supply

Ground

0V CN701-3

S/H

LSU CN1-3

Sample Hold Signal

+5V(H) 0V(L)

CN701-4

HSYNC

LSU CN1-4

+5V

Horizontal Synchronous Signal

0V CN701-5

LDEN

LSU CN1-5

Laser Control

+5V(H) 0V(L)

CN701-6

RETRACE

LSU CN1-6

+5V

Laser Control

0V CN701-7

GND

LSU CN1-7

Ground

0V CN701-8

POWCNTV

Laser Power Control Signal

LSU CN1-8

+1.1V

82 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

SPC PCB Signal Name Destination Pin No. CN701-9 PMCK LSU CN3-1

Signal Waveform

Function

+5V(H)

Polygon Motor Clock

0V(L) CN701-10 PMRDY

LSU CN3-2

Polygon Motor Ready Signal

+5V Ready

CN701-11 PMON

LSU CN3-3

0V Polygon Motor Rotation Signal

+5V ON

CN701-12 MGND

0V

LSU CN3-4

Ground

0V CN701-13 +24VM

LSU CN3-5

+24V

+24 VDC Power Supply

CN702 SPC PCB Signal Name Destination Pin No. CN702-1 +24VM PS PCB CN500-1

CN702-2

CPWM

Signal Waveform

Function

+24V

PS PCB CN500-2

+24 VDC Power Supply

Charge Control DC ON/OFF +5V PWM

0V CN702-3

GPWM

PS PCB CN500-3

Grid Control ON/OFF PWM

+5V 0V

CN702-4

N.C.

PS PCB CN500-4

CN702-5

DDCPWM

PS PCB CN500-5

No Connection

Development Control DC +5V ON/OFF PWM

0V CN702-6

TPWM

PS PCB CN500-6

Transfer Control Transfer +5V Output

0V

83 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

SPC PCB Signal Name Destination Pin No. CN702-7 TC PS PCB CN500-7

Signal Waveform

Function

+5V

Transfer Control Cleaning Output

0V CN702-8

CCRMT

PS PCB CN500-8

+5V

Charge Leak Detection Signal

0V CN702-9

MGND

PS PCB CN500-9

Ground

0V CN702-10 +24V

PS/LSU Fan -1

+24V

CN702-11 nFNRDTP

PS/LSU Fan -2

+5V

+24 VDC Power Supply

PS Fan Ready Signal

0V CN702-12 MGND

PS/LSU Fan -3

Ground

0V CN702-13 +5VP

PS PCB CN12-1

+5V

+5 VDC Power Supply

CN702-14 +5v

PS PCB CN12-2

+5V

+5 VDC Power Supply

CN702-15 +5v

PS PCB CN12-3

+5V

+5 VDC Power Supply

CN702-16 GND

PS PCB CN12-4

Ground

0V CN702-17 GND

PS PCB CN12-5

Ground

0V CN702-18 GND

PS PCB CN12-6

Ground

0V

84 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

SPC PCB Signal Name Destination Pin No. CN702-19 ZCRS PS PCB CN12-7

Signal Waveform

Function Heater Control Signal

+5V 0V

CN702-20 SSR

PS PCB CN12-8

Heater Control Signal

+5V(H) 0V(L)

CN702-21 ACSW

PS PCB CN12-9

+24V

Fuser Relay

ON 0V

CN702-22 +24VD1

PS PCB CN12-10

+24V

+24 VDC Power Supply

CN703 SPC PCB Signal Name Destination Pin No. CN703-1 MGND PS PCB CN10-1

Signal Waveform

Function Ground

0V CN703-2

MGND

PS PCB CN10-2

Ground

0V CN703-3

+24V

PS PCB CN10-3

+24V

+24 VDC Power Supply

CN703-4

+24V

PS PCB CN10-4

+24V

+24 VDC Power Supply

CN706 SPC PCB Signal Name Destination Pin No. 1st Tray Lift CN706-1 +24VM Motor

CN706-2

LIFT1

1st Tray Lift Motor

Signal Waveform

Function

+24V

+24 VDC Power Supply

1st Paper Tray Lift Motor Signal

+24V ON

0V

85 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

CN707 SPC PCB Signal Name Destination Pin No. CN707-1 +24VM CST2 PCB CN770-3

CN707-2

MGND

Signal Waveform

Function

+24V

CST2 PCB CN770-4

+24 VDC Power Supply

Ground

0V CN707-3

+5v

CST2 PCB CN770-5

CN707-4

GND

CST2 PCB CN770-6

+5V

+5 VDC Power Supply

Ground

0V CN707-5

OP3FLT

CST2 PCB CN770-7

+5V

Option Feed FIFO Latch

0V CN707-6

OP3RST

CST2 PCB CN770-8

Option Feed FIFO Reset

+5V Reset

CN707-7

OP3FOT

CST2 PCB CN770-9

0V +5V

Option Feed FIFO Output

0V CN707-8

OP3FCK

CST2 PCB CN770-10

Option Feed FIFO Clock

+5V 0V

CN707-9

OP3FLD

CST2 PCB CN770-11

Option Feed FIFO Load

+5V 0V

CN707-10 OP3ENB

CST2 PCB CN770-12

Option Feed FIFO Enable

+5V (H) 0V (L)

CN707-11 OP3CLK

CST2 PCB CN770-13

3rd Paper Tray Motor Clock

+5V 0V

86 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

SPC PCB Signal Name Destination Pin No. CN707-12 OP3FDIN CST2 PCB CN770-14

Signal Waveform

Function Option Feed FIFO Input

+5V 0V

CN707-13 ADF2

CST2 PCB CN771-1

2nd Paper Tray Feed Roller Drive Signal

ON

+5V

0V CN707-14 MRCLH2

CST2 PCB CN771-2

2nd Paper Tray Intermediate Roller Clutch Drive Signal

ON

+5V

0V CN707-15 LIFT2

CST2 PCB CN771-3

2nd Paper Tray Lift Motor Signal

ON

+5V

0V CN707-16 PCHK2

CST2 PCB CN771-4

+5V

2nd Paper Tray Paper Detection Signal

0V CN707-17 CST2

CST2 PCB CN771-5

+5V

2nd Paper Tray Detection Signal

0V CN707-18 UPLIMIT2

CST2 PCB CN771-6

+5V

2nd Paper Tray Paper Level Signal

0V CN707-19 FDPCHK2

CST2 PCB CN771-7

2nd Paper Tray Paper Registration Detection Signal

+5V(H) 0V(L)

CN707-20 JAMDOR2

CST2 PCB CN771-8

+5V

2nd Paper Tray Jam Access Cover Open Detection Signal

0V CN707-21 CSTOP

CST2 PCB CN771-9

2nd Paper Feed Module Detection Signal

0V CN707-23 +24VM

CST2 PCB CN771-11

+24V

+24 VDC Power Supply

87 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

SPC PCB Signal Name Destination Pin No. CN707-24 MGND CST2 PCB CN771-12

Signal Waveform

Function Ground

0V CN707-25 +24VM

CST2 PCB CN770-15

CN707-26 MGND

CST2 PCB CN770-16

+24V

+24 VDC Power Supply

Ground

0V CN709 SPC PCB Signal Name Destination Pin No. CN709-1 PCHK1 No Paper Sensor -1

Signal Waveform

Function

+5V

1st Paper Tray Paper Detection Signal

0V CN709-2

GND

No Paper Sensor -2

Ground

0V CN709-3

CN709-4

CN709-5

CN709-6

CN709-7

CN709-8

LDPSEN

UPLIMIT

GND

LDUPLSEN

CASET

GND

No Paper Sensor -3

+1.2V

Upper Limit Sensor -1

+5V

Photo Sensor DC Drive Voltage

1st Paper Tray Paper Level Signal

0V

Upper Limit Sensor -2

Ground

0V

Upper Limit Sensor -3

+1.2V

1st Tray Detection Sensor -1

+5V

Photo Sensor DC Drive Voltage

Paper Tray Detection Signal (1st Feeder)

0V

1st Tray Detection Sensor -2

Ground

0V

88 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

SPC PCB Signal Name Destination Pin No. CN709-9 LDCSTSEN 1st Tray Detection Sensor -3 CN709-10 RSEN

CN709-11 GND

CN709-12 LDRRSEN

Registration Roller Sensor -1

Signal Waveform

Function

+1.2V

Photo Sensor DC Drive Voltage

Registration Sensor Signal

+5V 0V

Registration Roller Sensor -2

Ground

0V

Registration Roller Sensor -3

+1.2V

Photo Sensor DC Drive Voltage

CN712 SPC PCB Signal Name Destination Pin No. CN712-1 LDSSN SSN PCB CN42-1

CN712-2

nA3SEN

Signal Waveform

Function

+1.2V

SSN PCB CN42-2

+5V

Photo Sensor DC Drive Voltage

Sheet Bypass Paper Size Detection Signal

0V CN712-3

GND

SSN PCB CN42-3

Ground

0V CN712-4

nB4SEN

SSN PCB CN42-4

+5V

Sheet Bypass B4 Paper Detection Signal

0V CN712-5

nA5SEN

SSN PCB CN42-5

+5V

Sheet Bypass Paper Size Detection Signal

0V CN712-6

CN712-7

nPEDSEN

GND

Bypass Feed No Paper Sensor -1

+5V

Sheet Bypass Paper Detection Signal

0V

Bypass Feed No Paper Sensor -2

Ground

0V

89 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

SPC PCB Signal Name Destination Pin No. CN712-8 LDPED Bypass Feed No Paper Sensor -3 CN712-9

nDUPSEN

Signal Waveform

Function

+1.2V

Duplex Sensor -1

+5V

Photo Sensor DC Drive Voltage

ADU Sensor Signal

0V CN712-10 GND

Duplex Sensor -2

Ground

0V CN712-11 LDDUX

CN712-14 nHFPESEN

CN712-15 GND

CN712-16 LDHFPE

Duplex Sensor -3

+1.2V

Bypass Feed Sensor -1

+5V

Photo Sensor DC Drive Voltage

Bypass Feed Sensor Signal

0V

Bypass Feed Sensor -2

Ground

0V

Bypass Feed Sensor -3

Photo Sensor DC Drive Voltage

+1.2V

CN715 SPC PCB Signal Name Destination Pin No. CN715-1 +24VM Registration Roller Clutch -1 CN715-2

RRCLCNT

Registration Roller Clutch -2

CN715-3

+24VM

Paper Feed Clutch -1

CN715-4

PFCLCNT

Paper Feed Clutch -2

Signal Waveform

Function

+24V

+24 VDC Power Supply

Registration Roller Drive Signal

+24V ON

0V

+24V

+24 VDC Power Supply

Paper Feed Clutch Drive Signal

+24V ON

0V

90 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

SPC PCB Signal Name Destination Pin No. CN715-5 +24VM Bypass Feed Solenoid -1 CN715-6

HFSOL

Bypass Feed Solenoid -2

Signal Waveform

Function

+24V

+24 VDC Power Supply

Temp Humidity Sensor Signal

+24V ON

0V

CN717 Refer to SC PC Board . CN719 SPC PCB Signal Name Destination Pin No. Duplex Solenoid CN719-1 +24VM

CN719-2

nDUXSOL

Duplex Solenoid

Signal Waveform

Function

+24V

+24 VDC Power Supply

ADU Solenoid Control Signal

+24V ON

0V

CN720 SPC PCB Signal Name Destination Pin No. CN720-3 +24VM PCL PCB -1

CN720-4

ELPCNT

Signal Waveform

Function

+24V

PCL PCB -2

+24V

+24 VDC Power Supply

Discharge Lamp

ON 0V

CN720-5

+24VM

Toner Density Sensor -2

CN720-6

TDREF

CN720-7

TDSEN

+24V

+24 VDC Power Supply

Toner Density Sensor -1

9V

Toner Density Reference Sensor

Toner Density Sensor -3

5V

4V Toner Density Sensor Signal

0V

91 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

SPC PCB Signal Name Destination Pin No. CN720-8 GND Toner Density Sensor -4 CN720-12 GND

CN720-13 nWTBSEN

Signal Waveform

Function Ground

0V

Waste Toner Sensor -1

Ground

0V

Waste Toner Sensor -2

+5V

Toner Waste Container Detection Sensor Signal

0V CN720-14 nTFSEN

Waste Toner Sensor -3

+5V

Toner Waste Sensor

0V CN720-15 LDWTB

CN720-16 LDTF

Waste Toner Sensor -4

+1.2V

Waste Toner Sensor -5

+1.5V

Photo Sensor DC Drive Voltage

Photo Sensor DC Drive Voltage

0V

CN720-17 +5v

Humidity Sensor -1

+5V

+5 VDC Power Supply

CN720-18 HUMISN

Humidity Sensor -2

5V

Temp Humidity Sensor Signal

0V CN720-19 GND

Humidity Sensor -3

Ground

0V CN720-20 TEMPSN

Humidity Sensor -4

5V

Temp Humidity Sensor Signal

0V CN720-21 +24VM

Total Counter -1

+24V

CN720-22 nCTCNT

Total Counter -2

+24V

+24 VDC Power Supply

Counter Drive Signal

0V

92 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

CN721 SPC PCB Signal Name Destination Pin No. CN721-1 THERM1 Thermistor -1

Signal Waveform

Function

5V

Thermistor Output Signal

0V CN721-2

THERM2

Thermistor -2

Ground

0V CN721-3

CN721-4

CN721-5

nHEXSEN

GND

LDHEX

Paper Exit Sensor -1

+5V

Paper Exit Sensor Signal

0V

Paper Exit Sensor -2

Ground

0V

Paper Exit Sensor -3

+1.2V

CN721-10 +24VFL

Exit Fan -1

+24V

CN721-11 nFNRDT

Exit Fan -2

+5V

Photo Sensor DC Drive Voltage

+20 / +24 VDC Power Supply

Fan Ready Signal

0V CN721-12 MGND

Exit Fan -3

Ground

0V CN722 SPC PCB Signal Name Destination Pin No. CN722-1 +24VM Toner Bottle Motor -1 CN722-2

CN722-3

BMCNT

+24VM

Signal Waveform

Toner Bottle Motor -2

Function

+24V

+24 VDC Power Supply

+24V

Toner Bottle Motor Control Signal

ON 0V

Toner Motor -1

+24V

+24 VDC Power Supply

93 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

SPC PCB Signal Name Destination Pin No. CN722-4 SMCNT Toner Motor -2

Signal Waveform

Function

+24V

Toner Motor Control Signal

ON 0V

CN722-5

CN722-6

CN722-7

BTHP

GND

LDBTHP

Toner Bottle Home Position Sensor -1

Toner Bottle Position Sensor Signal

+5V 0V

Toner Bottle Home Position Sensor -2

Ground

0V

Toner Bottle Home Position Sensor -3

+5V

Toner Bottle HP Sensor Signal

0V

CN723 SPC PCB Signal Name Destination Pin No. CN723-1 +24VM Main Motor -1

CN723-2

+24VM

Main Motor -2

CN723-3

MGND

Main Motor -3

Signal Waveform

Function

+24V

+24 VDC Power Supply

+24V

+24 VDC Power Supply

Ground

0V CN723-4

MGND

Main Motor -4

Ground

0V CN723-5

GND

Main Motor -5

Ground

0V CN723-6

+5v

Main Motor -6

CN723-7

nMMON

Main Motor -7

+5V

+5 VDC Power Supply

Main Motor Rotation Control Signal

+6.5V 0V

94 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

SPC PCB Signal Name Destination Pin No. CN723-8 nMMCK Main Motor -8

Signal Waveform

Function Main Motor Clock

+6.5V 0V

CN723-9

F/R

Main Motor -9

Direction of Rotation Signal

0V CN723-10 nMMRDY

Main Motor -10

Main Motor Ready Signal

+5V 0V

CN726 SPC PCB Signal Name Destination Pin No. Key Counter CN726-1 +24VM

CN726-2

KCNT

Signal Waveform

Function

+24V

Key Counter

+24V

+24 VDC Power Supply

Key Counter Option

0V CN726-3

GND

Key Counter

Ground

0V CN726-4

KCDET

Key Counter

+5V DETECT

Key Counter Option Detection

0V

CN726-5

N.C.

No Connection

CN726-6

N.C.

No Connection

95 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

2.10.4. PNL1 PC Board CN220 Refer to SC PC Board . CN223 PNL1 PCB Signal Name Destination Pin No. CN223-1 CSB1 LCD

Signal Waveform

Function Chip Select Signal

+3.3V 0V

CN223-2

RESETB

LCD

+3.3V RESET

CN223-3

RS

LCD

LCD Driver Reset Signal

0V +3.3V

Register Selection Control Signal

0V CN223-4

RW_WRB

LCD

LCD Control Signal

+3.3V 0V

CN223-5

E_RDB

LCD

Read/Write Execution Control Signal

+3.3V 0V

CN223-6

DB0

LCD

+3.3V

Data Signal

0V CN223-7

DB1

LCD

+3.3V

Data Signal

0V CN223-8

DB2

LCD

+3.3V

Data Signal

0V CN223-9

DB3

LCD

+3.3V

Data Signal

0V CN223-10 DB4

LCD

+3.3V

Data Signal

0V

96 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

PNL1 PCB Signal Name Destination Pin No. CN223-11 DB5 LCD

Signal Waveform

Function

+3.3V

Data Signal

0V CN223-12 DB6

LCD

+3.3V

Data Signal

0V CN223-13 DB7

LCD

+3.3V

Data Signal

0V CN223-14 VDD

LCD

+3.3V

+3.3 VDC Power Supply

CN223-15 VCL

LCD

+3.3V

LCD Power Supply

CN223-16 VSS

LCD

Ground

0V CN223-17 VOUT

LCD

+12.5V

CN223-18 C4+

LCD

+12.5V

CN223-19 C3+

LCD

+12.5V +9.5V

CN223-20 C1-

LCD

+3.3V 0V

CN223-21 C1+

LCD

+6.3V +3.3V

CN223-22 C2+

LCD

+9.5V +6.3V

Voltage Converter Input / Output

Capacitor 4 Positive Connection Pin for Converter Capacitor 3 Positive Connection Pin for Converter Capacitor 1 Negative Connection Pin for Converter Capacitor 1 Positive Connection Pin for Converter Capacitor 2 Positive Connection Pin for Converter

97 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

PNL1 PCB Signal Name Destination Pin No. CN223-23 C2LCD

Signal Waveform

Function

+3.3V 0V

Capacitor 2 Negative Connection Pin for Converter

CN223-24 V1

LCD

+6.7V

LCD Driver Supply Voltages

CN223-25 V2

LCD

+5.3V

LCD Driver Supply Voltages

CN223-26 V3

LCD

+2.6V

LCD Driver Supply Voltages

CN223-27 V4

LCD

+1.4V

LCD Driver Supply Voltages

CN223-28 V0

LCD

+8V

LCD Driver Supply Voltages

CN223-29 PS

LCD

+3.3V

Parallel / Serial Data Input Select Signal

CN223-30 HPMB

LCD

+3.3V

LCD driver Power Control Signal

CN230 PNL1 PCB Signal Name Destination Pin No. CN230-1 LED0 PNL2 PCB CN250-1

Signal Waveform

Function PNL LED Control Signal

0V CN230-2

CN230-3

KIN7

LED1

PNL2 PCB CN250-2

Key Pressed

+3.3V

PNL Key Signal (Key Line)

0V

PNL2 PCB CN250-3

PNL LED Control Signal

0V

98 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

PNL1 PCB Signal Name Destination Pin No. CN230-4 KIN6 PNL2 PCB CN250-4

CN230-5

LED2

Signal Waveform

Key Pressed

Function

+3.3V

PNL Key Signal (Key Line)

0V

PNL2 PCB CN250-5

PNL LED Control Signal

0V CN230-6

CN230-7

SCN0

LED3

PNL2 PCB CN250-6

Key Scan

+3.3V

PNL Key Signal (Scan Line)

0V PNL LED Control Signal

PNL2 PCB CN250-7

0V CN230-8

CN230-9

SCN1

LED4

PNL2 PCB CN250-8

Key Scan

+3.3V

PNL Key Signal (Scan Line)

0V

PNL2 PCB CN250-9

PNL LED Control Signal

0V CN230-10 KIN5

CN230-11 LED5

PNL2 PCB CN250-10

Key Pressed

+3.3V

PNL Key Signal (Key Line)

0V PNL LED Control Signal

PNL2 PCB CN250-11

0V CN230-12 KIN4

CN230-13 LEDCT2

PNL2 PCB CN250-12

Key Pressed

PNL2 PCB CN250-13

CN230-15 LEDCT3

PNL Key Signal (Key Line)

0V

+5V

PNL LED Control Signal

LED ON

0V CN230-14 KIN3

+3.3V

PNL2 PCB CN250-14

Key Pressed

PNL2 PCB CN250-15

+3.3V

PNL Key Signal (Key Line)

0V

+5V

PNL LED Control Signal

LED ON

0V

99 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

PNL1 PCB Signal Name Destination Pin No. CN230-16 KIN2 PNL2 PCB CN250-16

CN230-17 LEDCT4

Signal Waveform

PNL Key Signal (Key Line)

0V

+5V

PNL LED Control Signal

LED ON

0V CN230-18 BAT+

+3.3V

Key Pressed

PNL2 PCB CN250-17

Function

PNL2 PCB CN250-18

+3V

Lithium Battery

CN231 PNL1 PCB Signal Name Destination Pin No. CN231-1 +SLP PNL2 PCB CN251-1

CN231-2

nLEDSLP

Signal Waveform

Function

+5VP

PNL2 PCB CN251-2

+5VP

Energy Saver Lamp LED Power Supply

Energy Saver Lamp LED Control Signal

0V CN231-3

nSLPKY

PNL2 PCB CN251-3

+3.3V PUSH

CN231-4

GND

Energy Saver Key Signal

0V

PNL2 PCB CN251-4

Ground

0V CN231-5

LEDCT0

PNL2 PCB CN251-5

+5V 0V

LED ON

CN231-6

BZ+

PNL2 PCB CN251-6

+12V (+24V)

CN231-7

LEDCT1

PNL2 PCB CN251-7

+5V 0V

CN231-8

BZ-

PNL2 PCB CN251-8

PNL LED Control Signal

Buzzer Signal (+) +24V: Loud

PNL LED Control Signal

LED ON +12V (+24V)

Buzzer Signal +24V: Loud

0V

100 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

PNL1 PCB Signal Name Destination Pin No. CN231-9 LED6 PNL2 PCB CN251-9

Signal Waveform

Function PNL LED Control Signal

0V CN231-10 SCN2

CN231-11 KIN0

CN231-12 KIN1

PNL2 PCB CN251-10

PNL2 PCB CN251-11

PNL2 PCB CN251-12

Key Scan

Key Pressed

Key Pressed

+3.3V

PNL Key Signal (Scan Line)

0V +3.3V

PNL Key Signal (Key Line)

0V +3.3V

PNL Key Signal (Key Line)

0V

CN232 PNL1 PCB Signal Name Destination Pin No. CN232-1 SCN4 PNL3 PCB CN252-1

CN232-2

CN232-3

CN232-4

CN232-5

SCN5

SCN3

SCN6

KIN3

Signal Waveform

Key Scan

PNL3 PCB CN252-2

Key Scan

PNL3 PCB CN252-3

Key Scan

PNL3 PCB CN252-4

PNL3 PCB CN252-5

CN232-6

N.C.

PNL3 PCB CN252-6

CN232-7

KIN2

PNL3 PCB CN252-7

Key Scan

Key Pressed

Function

+3.3V

PNL Key Signal (Scan Line)

0V +3.3V

PNL Key Signal (Scan Line)

0V +3.3V

PNL Key Signal (Scan Line)

0V +3.3V

PNL Key Signal (Scan Line)

0V +3.3V

PNL Key Signal (Key Line)

0V No Connection

Key Pressed

+3.3V

PNL Key Signal (Key Line)

0V

101 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

PNL1 PCB Signal Name Destination Pin No. CN232-8 KIN7 PNL3 PCB CN252-8

CN232-9

KIN1

CN232-10 KIN0

PNL3 PCB CN252-9

PNL3 PCB CN252-10

Signal Waveform

Key Pressed

Key Pressed

Key Pressed

Function

+3.3V

PNL Key Signal (Key Line)

0V +3.3V

PNL Key Signal (Key Line)

0V +3.3V

PNL Key Signal (Key Line)

0V

CN233 PNL1 PCB Signal Name Destination Pin No. CN233-1 +DAT PNL3 PCB CN253-1

Signal Waveform

Function

+24V

DATA Lamp LED Power Supply

0V CN233-2

N.C.

PNL3 PCB CN253-2

CN233-3

+ALM

PNL3 PCB CN253-3

No Connection

+24V

ALARM Lamp LED Power Supply

0V CN233-4

CN233-5

KIN4

+ACT

PNL3 PCB CN253-4

Key Pressed

PNL3 PCB CN253-5

+3.3V

PNL Key Signal (Key Line)

0V +24V

ACTIVE Lamp LED Power Supply

0V CN233-6

CN233-7

KIN5

nLEDACT

PNL3 PCB CN253-6

Key Pressed

PNL3 PCB CN253-7

+3.3V

PNL Key Signal (Key Line)

0V +3.3V

ACTIVE Lamp LED Control Signal

0V CN233-8

KIN6

PNL3 PCB CN253-8

Key Pressed

+3.3V

PNL Key Signal (Key Line)

0V

102 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

PNL1 PCB Signal Name Destination Pin No. CN233-9 nLEDALM PNL3 PCB CN253-9

Signal Waveform

Function

+3.3V

ALARM Lamp LED Control Signal

0V CN233-10 LEDCT0

PNL3 PCB CN253-10

PNL LED Control Signal

+3.3V

DATA Lamp LED Control Signal

LED ON

0V CN233-11 nLEDDAT

+5V

PNL3 PCB CN253-11

0V CN233-12 LED9

PNL3 PCB CN253-12

PNL LED Control Signal

0V CN233-13 LEDCT4

PNL3 PCB CN253-13

+5V LED ON

0V CN233-14 LED8

PNL LED Control Signal

PNL3 PCB CN253-14

PNL LED Control Signal

0V CN233-15 LEDCT3

PNL3 PCB CN253-15

+5V LED ON

0V CN233-16 LED7

PNL LED Control Signal

PNL3 PCB CN253-16

PNL LED Control Signal

0V CN233-17 LEDCT2

PNL3 PCB CN253-17

PNL LED Control Signal

+5V

PNL LED Control Signal

LED ON

0V CN233-18 LEDCT1

+5V

PNL3 PCB CN253-18

LED ON

0V CN234 PNL1 PCB Signal Name Destination Pin No. CN234-1 KIN4 PNL4 PCB CN280-1

Signal Waveform

Key Pressed

Function

+3.3V

PNL Key Signal (Key Line)

0V

103 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

PNL1 PCB Signal Name Destination Pin No. CN234-2 KIN5 PNL4 PCB CN280-2

CN234-3

CN234-4

CN234-5

CN234-6

CN234-7

CN234-8

CN234-9

KIN3

KIN6

KIN2

KIN7

KIN1

SCN11

KIN0

CN234-10 SCN10

CN234-11 SCN8

CN234-12 SCN9

CN234-13 nOPT

PNL4 PCB CN280-3

PNL4 PCB CN280-4

PNL4 PCB CN280-5

PNL4 PCB CN280-6

PNL4 PCB CN280-7

Signal Waveform

Key Pressed

Key Pressed

Key Pressed

Key Pressed

Key Pressed

Key Pressed

PNL4 PCB CN280-8

PNL4 PCB CN280-9

Key Scan

Key Pressed

PNL4 PCB CN280-10

Key Scan

PNL4 PCB CN280-11

Key Scan

PNL4 PCB CN280-12

Key Scan

PNL4 PCB CN280-13

Function

+3.3V

PNL Key Signal (Key Line)

0V +3.3V

PNL Key Signal (Key Line)

0V +3.3V

PNL Key Signal (Key Line)

0V +3.3V

PNL Key Signal (Key Line)

0V +3.3V

PNL Key Signal (Key Line)

0V +3.3V

PNL Key Signal (Key Line)

0V +3.3V

PNL Key Signal (Scan Line)

0V +3.3V

PNL Key Signal (Key Line)

0V +3.3V

PNL Key Signal (Scan Line)

0V +3.3V

PNL Key Signal (Scan Line)

0V +3.3V

PNL Key Signal (Scan Line)

0V +3.3V

PNL4 Detection 0V: Detection

0V

104 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

PNL1 PCB Signal Name Destination Pin No. CN234-14 GND PNL4 PCB CN280-14

Signal Waveform

Function Ground

0V

105 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

2.10.5. PS PC Board CN10 Refer to SPC PC Board . CN11 Refer to SC PC Board . CN12 Refer to SPC PC Board . CN500 Refer to SPC PC Board .

106 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

2.10.6. ADF PC Board CN21 Refer to SPC PC Board . CN22 ADF PCB Signal Name Destination Pin No. CN22-1 OUTA ADF Motor -1

Signal Waveform

Function Motor Control Signal

+24V 0V

CN22-2

+24V

ADF Motor -2

CN22-3

IOUTA

ADF Motor -3

+24V

+24 VDC Power Supply

Motor Control Signal

+24V 0V

CN22-4

OUTB

ADF Motor -4

Motor Control Signal

+24V 0V

CN22-5

+24V

ADF Motor -5

CN22-6

IOUTB

ADF Motor -6

+24V

+24 VDC Power Supply

Motor Control Signal

+24V 0V

CN22-7

+24VOPF

ADF Roller Clutch -1

CN22-8

nCCLH2

ADF Roller Clutch -4

CN22-9

+24VOPF

Feed 2 Roller Clutch -1

CN22-10

nCCLH1

Feed 2 Roller Clutch -4

+24V

+24 VDC Power Supply

ADF Roller Clutch Control Signal

+24V ON

0V +24V

+24 VDC Power Supply

Feed 2 Roller Clutch Control Signal

+24V ON

0V

107 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

CN24 ADF PCB Signal Name Destination Pin No. CN24-1 +24VOPF Inverting Roller Clutch -1 CN24-2

nCCLH3

Inverting Roller Clutch -4

Signal Waveform

Function

+24V

+24 VDC Power Supply

Inverting Roller Clutch Control Signal

+24V ON

0V

CN25 ADF PCB Signal Name Destination Pin No. CN25-1 +24VOPF Stamp Solenoid

CN25-2

nASTAMP

Stamp Solenoid

Signal Waveform

Function

+24V

+24 VDC Power Supply

Stamp Control Signal

+24V ON

0V

CN26 ADF PCB Signal Name Destination Pin No. CN26-1 +24VOPC Release Lever Plate Solenoid -1 CN26-2

CN26-3

nAPACHG

nAKEEP1

Release Lever Plate Solenoid -2 Reversing Guide 1 Solenoid -1

CN26-4

+24VOPC

Reversing Guide 1 Solenoid -2

CN26-5

nAKEEP2

Reversing Guide 1 Solenoid -3

CN26-6

+24VOPF

Signal Waveform

Function

+24V

Release Lever Plate Solenoid Control Signal

+24V ON

0V Reversing 1 Guide Solenoid Control Signal

+24V ON

0V

+24V

+24 VDC Power Supply

Reversing 1 Guide Solenoid Control Signal

+24V ON

Duplex 2 Guide Solenoid -1

+24 VDC Power Supply

0V

+24V

+24 VDC Power Supply

108 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

ADF PCB Signal Name Destination Pin No. CN26-7 nAPICR Duplex 2 Guide Solenoid -2

Signal Waveform

Function Release Lever Plate Solenoid Control Signal

+24V ON

0V

CN27 ADF PCB Signal Name Destination Pin No. CN27-1 nAAPNT Original Detection Sensor -1 CN27-2

CN27-3

GND

+5v

Signal Waveform

Function Original Detection Signal

+5V ON

0V

Original Detection Sensor -2

Ground

0V

Original Detection Sensor -3

+5V

+5 VDC Power Supply

CN28 ADF PCB Signal Name Destination Pin No. CN28-1 nAADL1 Original Lengh Sensor 1 -1 CN28-2

GND

+5v

Original Lengh Sensor 1 -3

CN28-4

nAADL2

Original Lengh Sensor 2 -1

CN28-6

GND

+5v

Function Original Length Detection Signal

+5V ON

Original Lengh Sensor 1 -2

CN28-3

CN28-5

Signal Waveform

0V Ground

0V +5V

Original Length Detection Signal

+5V ON

Original Lengh Sensor 2 -2

+5 VDC Power Supply

0V Ground

0V

Original Lengh Sensor 2 -3

+5V

+5 VDC Power Supply

109 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

ADF PCB Signal Name Destination Pin No. CN28-7 nAB4S SNS PCB CN41-4

Signal Waveform

Function Original Width Detection Signal

+5V(H) 0V

CN28-8

nAA3S

SNS PCB CN41-2

Original Width Detection Signal

+5V 0V

CN28-9

GND

SNS PCB CN41-3

Ground

0V CN28-10

+5v

SNS PCB CN41-1

+5V

+5 VDC Power Supply

CN29 ADF PCB Signal Name Destination Pin No. CN29-1 nAB1SN Read Point Sensor -1 CN29-2

GND

+5v

Read Point Sensor -3

CN29-4

nAOAC

ADF Cover Open Detection Sensor -1

CN29-6

GND

+5v

Function Read Point Detection Signal

+5V ON

Read Point Sensor -2

CN29-3

CN29-5

Signal Waveform

0V Ground

0V +5V

+5 VDC Power Supply

ADF Cover Open Detection Signal

+5V OPEN 0V

ADF Cover Open Detection Sensor -2

Ground

0V

ADF Cover Open Detection Sensor -3

+5V

+5 VDC Power Supply

110 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

CN30 ADF PCB Signal Name Destination Pin No. CN30-1 nAEJC Eject Sensor -1

Signal Waveform

Function

+5V ON

Original Eject Detection Signal

0V CN30-2

GND

Eject Sensor -2

Ground

0V CN30-3

+5v

Eject Sensor -3

CN30-4

nAB2SN

Duplex Eject Sensor -1

CN30-5

GND

+5v

Duplex Eject Sensor -3

CN30-7

nAREV

ADF Exit Cover Sensor -1

CN30-9

GND

+5v

+5 VDC Power Supply

Duplex Eject Detection Signal

+5V ON

Duplex Eject Sensor -2

CN30-6

CN30-8

+5V

0V Ground

0V +5V

+5 VDC Power Supply

ADF Exit Cover Open Detection Signal

+5V OPEN 0V

ADF Exit Cover Sensor -2

Ground

0V

ADF Exit Cover Sensor -3

+5V

+5 VDC Power Supply

111 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

2.10.7. CST2 PC Board CN770 Refer to SPC PC Board . CN771 Refer to SPC PC Board . CN772 CST2 PCB Signal Name Destination Pin No. CN772-1 +24VM CST3 PCB CN807-1

CN772-2

MGND

Signal Waveform

Function

+24V

CST3 PCB CN807-2

+24 VDC Power Supply

Ground

0V CN772-3

+5v

CST3 PCB CN807-3

CN772-4

GND

CST3 PCB CN807-4

+5V

+5 VDC Power Supply

Ground

0V CN772-5

OP3RST

CST3 PCB CN807-5

Option Feed FIFO Reset

+5V Reset

CN772-6

OP3FLT

CST3 PCB CN807-6

0V

+5V

Option Feed FIFO Latch

0V CN772-7

OP3FCK

CST3 PCB CN807-7

Option Feed FIFO Clock

+5V Reset

CN772-8

OP3FOT

CST3 PCB CN807-8

0V +5V

Option Feed FIFO Output

0V CN772-9

OP3ENB

CST3 PCB CN807-9

Option Feed FIFO Enable

+5V (H) 0V (L)

CN772-10 OP3FLD

CST3 PCB CN807-10

+5V

Option Feed FIFO Load

0V

112 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

CST2 PCB Signal Name Destination Pin No. CN772-11 OP3FDIN CST3 PCB CN807-11

Signal Waveform

Function Option Feed FIFO Input

+5V 0V

CN772-14 +24VM

CST3 PCB CN807-13

CN772-13 GND

CST3 PCB CN807-14

+24V

+24 VDC Power Supply

Ground

0V CN773 CST2 PCB Signal Name Destination Pin No. CN773-1 +24VM Paper Feed Clutch -1 CN773-2

ADF2

Signal Waveform

Paper Feed Clutch -2

+24V

+24 VDC Power Supply

+24V

2nd Paper Tray Feed Roller Drive Signal

ON CN773-3

+24VM

Intermediate Roller Clutch -1

CN773-4

MRCLH2

Intermediate Roller Clutch -2

Function

0V +24V

+24V ON

+24 VDC Power Supply

2nd Paper Tray Intermediate Roller Clutch Drive Signal

0V

CN774 CST2 PCB Signal Name Destination Pin No. CN774-1 +24VM 2nd Tray Lift Motor

CN774-2

LIFTM2

Signal Waveform

2nd Tray Lift Motor

ON

Function

+24V

+24 VDC Power Supply

+24V

2nd Paper Tray Lift Motor Drive Signal

0V

113 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

CN775 CST2 PCB Signal Name Destination Pin No. CN775-1 PCHK2 No Paper Sensor -1

Signal Waveform

Function

+5V

2nd Paper Tray Paper Detection Signal

0V CN775-2

GND

No Paper Sensor -2

Ground

0V CN775-3

CN775-4

CN775-5

CN775-6

LDPHK2

UPLMT2

GND

LDUPL2

No Paper Sensor -3

+1.2V

Upper Limit Sensor -1

+5V

Photo Sensor DC Drive Voltage

2nd Paper Tray Paper Level Signal

0V

Upper Limit Sensor -2

Ground

0V

Upper Limit Sensor -3

+1.2V

Photo Sensor DC Drive Voltage

CN776 CST2 PCB Signal Name Destination Pin No. CN776-1 FDPCHK2 Registration Sensor -1

Signal Waveform

Function

+5V

2nd Paper Tray Paper Registration Detection Signal

0V CN776-2

CN776-3

GND

LDFPCHK2

Registration Sensor -2

Ground

0V

Registration Sensor -3

+1.2V

Photo Sensor DC Drive Voltage

114 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

CN777 CST2 PCB Signal Name Destination Pin No. CN777-1 nCST2 2nd Tray Detection Sensor -1

Signal Waveform

Function

+5V

2nd Paper Tray Detection Signal

0V CN777-2

CN777-3

GND

LDCST2

2nd Tray Detection Sensor -2

Ground

0V

2nd Tray Detection Sensor -3

+1.2V

Photo Sensor DC Drive Voltage

CN778 CST2 PCB Signal Name Destination Pin No. CN778-1 JAMDOR2 Jam Cover Open Sensor -1 CN778-2

CN778-3

GND

LDJAM2

Signal Waveform

Function

+5V OPEN 0V

Jam Cover Open Sensor -2

2nd Paper Tray Jam Access Cover Open Detection Signal Ground

0V

Jam Cover Open Sensor -3

+1.2V

Photo Sensor DC Drive Voltage

115 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

2.10.8. CST3 PC Board CN800 CST3 PCB Signal Name Destination Pin No. CN800-1 PCHK3 No Paper Sensor -1

Signal Waveform

Function

+5V

3rd Paper Tray Paper Detection Signal

0V CN800-2

GND

No Paper Sensor -2

Ground

0V CN800-3

CN800-4

CN800-5

CN800-6

LDPHK3

UPLIMIT3

GND

LDUPL3

No Paper Sensor -3

+1.2V

Upper Limit Sensor -1

+5V

Photo Sensor DC Drive Voltage

3rd Paper Tray Paper Level Signal

0V

Upper Limit Sensor -2

Ground

0V

Upper Limit Sensor -3

+1.2V

Photo Sensor DC Drive Voltage

CN801 CST3 PCB Signal Name Destination Pin No. CN801-1 CST3 3rd Tray Detection Sensor -1

Signal Waveform

Function

+5V

3rd Paper Tray Detection Signal

0V CN801-2

CN801-3

GND

LDCST3

3rd Tray Detection Sensor -2

Ground

0V

3rd Tray Detection Sensor -3

+1.2V

Photo Sensor DC Drive Voltage

116 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

CN802 CST3 PCB Signal Name Destination Pin No. CN802-1 JAMDOR3 Jam Cover Open Sensor -1

Signal Waveform

Function

+5V

3rd Paper Tray Jam Access Cover Open Detection Signal

0V CN802-2

CN802-3

GND

LDJAM3

Jam Cover Open Sensor -2

Ground

0V

Jam Cover Open Sensor -3

+1.2V

Photo Sensor DC Drive Voltage

CN803 CST3 PCB Signal Name Destination Pin No. CN803-1 FDPCHK3 Registration Sensor -1 CN803-2

CN803-3

GND

LDFPCHK3

Signal Waveform

Function

+5V 0V

Registration Sensor -2

3rd Paper Tray Paper Registration Detection Signal Ground

0V

Registration Sensor -3

Photo Sensor DC Drive Voltage

+1.5V

CN804 CST3 PCB Signal Name Destination Pin No. CN804-1 +24VM 3rd Tray Lift Motor

CN804-2

nLIFTM3

3rd Tray Lift Motor

Signal Waveform

Function

+24V

+24 VDC Power Supply

3rd Paper Tray Lift Motor Drive Signal

+24V 0V

CN805 CST3 PCB Signal Name Destination Pin No. CN805-1 +24VM 3rd Tray Drive Motor -1

Signal Waveform

+24V

Function +24 VDC Power Supply

117 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

CST3 PCB Signal Name Destination Pin No. CN805-2 MGND 3rd Tray Drive Motor -2

Signal Waveform

Function Ground

0V

CN805-3

N.C.

3rd Tray Drive Motor -3

CN805-4

P/S

3rd Tray Drive Motor -4

+5V

3rd Tray Drive Motor -5

+5V

CN805-5

LD

No Connection

Motor Start/Stop

0V Motor Lock Detection Signal

0V

CN806 CST3 PCB Signal Name Destination Pin No. CN806-1 +24VM Paper Feed Clutch -1 CN806-2

ADF3

Paper Feed Clutch -2

Signal Waveform

Function

+24V

+24 VDC Power Supply

3rd Paper Tray Feed Roller Drive Signal

+24V 0V

CN806-3

+24VM

Intermediate Roller Clutch -1

CN806-4

MRCLH3

Intermediate Roller Clutch -2

+24V

+24 VDC Power Supply

3rd Paper Tray Intermediate Roller Clutch Drive Signal

+24V 0V

CN808 CST3 PCB Signal Name Destination Pin No. CN808-1 +24VM CST2 PCB CN770-3

CN808-2

MGND

Signal Waveform

Function

+24V

CST2 PCB CN770-4

+24 VDC Power Supply

Ground

0V

118 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

CST3 PCB Signal Name Destination Pin No. CN808-3 +5v CST2 PCB CN770-5

CN808-4

GND

Signal Waveform

Function

+5V

CST2 PCB CN770-6

+5 VDC Power Supply

Ground

0V CN808-5

N.C.

CST2 PCB CN770-7

No Connection

CN808-6

N.C.

CST2 PCB CN770-8

No Connection

CN808-7

N.C.

CST2 PCB CN770-9

No Connection

CN808-8

N.C.

CST2 PCB CN770-10

No Connection

CN808-9

N.C.

CST2 PCB CN770-11

No Connection

CN808-10 N.C.

CST2 PCB CN770-12

No Connection

CN808-12 N.C.

CST2 PCB CN770-14

No Connection

CN808-13 ADF4

CST2 PCB CN771-1

+24V ON

CN808-14 MRCLH4

CST2 PCB CN771-2

CN808-15 LIFT4

0V +24V

ON CST2 PCB CN771-3

4th Paper Tray Feed Roller Drive Signal

4th Paper Tray Intermediate Roller Clutch Drive Signal

0V

+5V

4th Paper Tray Lift Motor Signal

0V

119 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

CST3 PCB Signal Name Destination Pin No. CN808-16 PCHK4 CST2 PCB CN771-4

Signal Waveform

Function

+5V

4th Paper Tray Paper Detection Signal

0V CN808-17 CST4

CST2 PCB CN771-5

+5V

4th Paper Tray Detection Signal

0V CN808-18 UPLIMIT4

CST2 PCB CN771-6

+5V

4th Paper Tray Paper Level Signal

0V CN808-19 FDPCHK4

CST2 PCB CN771-7

+5V 0V

CN808-20 JAMDOR4

CST2 PCB CN771-8

+5V 0V

CN808-21 CSTOP4

CST2 PCB CN771-9

4th Paper Tray Paper Registration Detection Signal 4th Paper Tray Jam Access Cover Open Detection Signal 4th Paper Feed Module Detection Signal

0V CN808-23 +24VM

CST2 PCB CN771-11

CN808-24 MGND

CST2 PCB CN771-12

+24V

+24 VDC Power Supply

Ground

0V CN808-25 N.C.

CST2 PCB CN770-15

No Connection

CN808-26 N.C.

CST2 PCB CN770-16

No Connection

120 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

2.10.9. FXB PC Board CN391 FXB PCB Signal Name Destination Pin No. CN391-1 +5VP MJR PC Board CN25-1

CN391-2

GND

Signal Waveform

Function

+5V

MJR PC Board CN25-2

+5 VDC Power Supply

Ground

0V CN391-3

+24V

MJR PC Board CN25-3

CN391-4

pCMLD

MJR PC Board CN25-4

+24V

+5V(H)

ON

OFF CN391-5

nHKOF

MJR PC Board CN25-5

Line Switching Relay Drive Signal H : CML On 0V(L) L : CML Off External Phone Off-Hook Detection Signal H : On Hook L : Off Hook

+5V(H) 0V(L)

CN391-6

CN391-7

nCTON

AGND

MJR PC Board CN25-6

+24 VDC Power Supply

Ring Detection Signal

H: Standby Mode L: Ringing

MJR PC Board CN25-7

Ground

0V CN392 FXB PCB Signal Name Destination Pin No. CN392-1 L2 MJR PC Board CN22-1

CN392-3

L1

Signal Waveform

Function Line Signal

MJR PC Board CN22-2

Line Signal

121 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

CN393 FXB PCB Signal Name Destination Pin No. CN393-1 pSPKOT Speaker -1

CN393-2

GND

Signal Waveform

Function

+1V (Max) -1V (Min)

Speaker -2

Line Dial Tone Signal

Ground

0V

122 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

2.10.10. MJR PC Board CN22 Refer to FXB PC Board . CN25 Refer to FXB PC Board .

123 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

3 Troubleshooting 3.1.

Error Codes (For Copier)

The self-diagnostic functions detect troubles in the important components of the copier. When any trouble occurs, the copier stops.

3.1.1.

User Error Codes (U Code) U20 U22

U21 U90

U00 U18

U01 U13 / 14 / 15 / 16 / 25 U07

Note: Uxx, and a message will appear on the Panel Display.

Code U00

U01

U07

User Error Codes (U Code) Table Item Possible Cause(s) Key Counter 1. Card Key not installed. 2. Key Counter Harness disconnected. 3. Department Code not assigned. Close Front Cover 1. Front Cover / Side Cover open. 2. Front Cover / Side Cover Sensor disconnected. 3. Front Cover / Side Cover Sensor defective 4. PS connector disconnected. 5. PS defective. 6. SPC PCB connector disconnected. 7. SPC PCB defective. Close Tray Cover 1. Tray Cover open. 2. Tray Unit incorrectly installed. 3. Tray Unit connector disconnected. 4. Tray Unit Sensor disconnected. 5. Tray Unit Sensor defective. 6. PS connector disconnected. 7. PS defective. 8. CST2/CST3 PCB connector disconnected. 9. CST2/CST3 PCB defective.

124 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Code U13

U14 U15

U16 U18 U20

U21

U22

U25 U90

User Error Codes (U Code) Table Item Possible Cause(s) Add Toner 1. Toner Bottle incorrectly installed. 2. Low Toner. 3. Toner Sensor disconnected. 4. Toner Sensor defective. 5. SPC PCB connector disconnected. 6. SPC PCB defective. Replace Toner Waste 1. Toner Waste Container full. Container (See Sect. 3.5.3. of the Service Manual) No Toner Waste Container 1. Toner Waste Container not installed. 2. Toner Waste Container Sensor disconnected. 3. Toner Waste Container Sensor defective. No Developer Unit 1. Developer Unit not installed. Total Copy Limit Over 1. Department Copy Counter full. Close ADF Cover 1. ADF Cover open. 2. ADF not installed correctly. 3. ADF Cover Sensor disconnected. 4. ADF Cover Sensor defective. 5. PS connector disconnected. 6. PS defective. Close ADF 1. ADF, and ADF Cover open. 2. ADF Sensor disconnected. 3. ADF Sensor defective. Close ADF Exit Cover 1. ADF Exit Cover open. 2. ADF not installed correctly. 3. ADF Exit Cover Sensor disconnected. 4. ADF Exit Cover Sensor defective. 5. PS connector disconnected. 6. PS defective. Shake Toner Bottle 1. Toner blocked in the Toner Bottle. Replace Battery 1. Internal battery requires replacement.

125 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

3.1.2.

Jam Error Codes (J Code) A

B

C D2 D3 D4

Section A B C D2 D3 D4

Jam Location ADF / i-ADF / Scanner Paper Transport / Exit Area Paper Entry Area 2nd Paper Tray 3rd Paper Tray 4th Paper Tray

• Jam Sensor Location of i-ADF Original Detection Sensor

Original Length Sensor

Read Point Sensor

Eject Sensor Duplex Eject Sensor

126 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

• Jam Sensor Location of ADF Read Point, and Eject Sensor

Original Length Sensor

Original Detection Sensor

• Jam Sensor Location of Printer

Paper Exit Sensor

ADU Sensor

Registration Sensor

2nd Paper Tray Path Sensor

3rd Paper Tray Path Sensor

4th Paper Tray Path Sensor

127 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

• Paper Transport / Exit / Entry / Feed Unit Area

Code J00 J01 J02 J03 J04 J07 J08 J09 J12 J13 J14 J19 J22 J23 J24 J30 J31 J32 J33 J45 J46 J48

Jam Error Codes (J Code) Table Contents Section The Registration Sensor does not detect paper within a predetermined time after the B paper starts feeding. (Sheet Bypass) The Registration Sensor does not detect paper within a predetermined time after the Paper Feed Roller starts rotating. (1st Paper Tray) The 2nd Paper Tray Path Sensor does not detect paper within a predetermined time D2 after the Paper Feed Roller starts rotating. (2nd Paper Tray) The 3rd Paper Tray Path Sensor does not detect paper within a predetermined time D3 after the Paper Feed Roller starts rotating. (3rd Paper Tray) The 4th Paper Tray Path Sensor does not detect paper within a predetermined time D4 after the Paper Feed Roller starts rotating. (4th Paper Tray) The Registration Sensor does not detect paper within a predetermined time after the B, D2 2nd Paper Tray Path Sensor is activated. (2nd Paper Tray) The Registration Sensor did not detect paper within a predetermined time after the D3 3rd Paper Tray Path Sensor is activated. (3rd Paper Tray) The Registration Sensor did not detect paper within a predetermined time after the D4 4th Paper Tray Path Sensor is activated. (4th Paper Tray) The 2nd Paper Tray Path Sensor does not go off within a predetermined time after B, D2 the Paper Tray Path Sensor is activated. The 3rd Paper Tray Path Sensor does not go off within a predetermined time after the D3 Paper Tray Path Sensor is activated. The 4th Paper Tray Path Sensor does not go off within a predetermined time after the D4 Paper Tray Path Sensor is activated. The Registration Sensor does not detect within a predetermined time after the ADU B Sensor is activated. The 2nd Paper Tray Path Sensor detect paper at the time of the initials. B, D2 The 3rd Paper Tray Path Sensor detect paper at the time of the initials. D2, D3 The 4th Paper Tray Path Sensor detect paper at the time of the initials. D3, D4 The Registration Sensor does not go off within a predetermined time after the Sensor B is activated. (Sheet Bypass) The Registration Sensor does not go off within a predetermined time after the Sensor is activated. (Except Sheet Bypass) The Registration Sensor does not go off within a predetermined time after the ADU Sensor is activated. (DP-8020E) The Registration Sensor detects paper during non-printing mode. The Paper Exit Sensor keeps detecting paper after a predetermined time, during non-printing mode. The Paper Exit Sensor does not go off within a predetermined time after the Sensor is activated. The Paper Exit Sensor does not detect paper within a predetermined time after the Registration Sensor is activated.

J70-79 (See the following table below) J82 The ADU Sensor does not detect paper within a predetermined time after the Duplex Feed Roller starts rotating. J85 The ADU Sensor does not go off within a predetermined time after the Sensor is activated. J87 The ADU Sensor detects paper during non-printing mode. J90 Abnormal Paper Jam: During printing the Front Door was opened, etc.

B

B, C, D

128 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Jam Error Codes (J Code) Table Contents A Paper Tray was pulled out while feeding paper.

Code J91 J92-94 (See the following table below) J95 The paper size of a Tray differs from the Machine setting size. J97 After passing the Registration Sensor (Roller), the Paper does not clear the sensor within a predetermined time period. J98 No VRDY Signal after a predetermined time has lapsed. J99 No VSYNC Signal within a predetermined time after VRDY Signal is activated.

Section C B

• i-ADF / ADF Area

Code J70 J71 J72 J73

J76 J78 J79 J92 J93 J94

Jam Error Codes (J Code) Table Contents The Read Point Sensor does not detect paper within a predetermined time after the original starts feeding. The Read Point Sensor keeps detecting paper within a predetermined time after scanning starts. The Eject Sensor does not detect paper within a predetermined time after the Read Point Sensor is activated. 1. The Eject Sensor keeps detecting paper within a predetermined time after scanning starts. 2. The Eject Sensor keeps detecting paper within a predetermined time after the Read Point Sensor is deactivated. The Duplex Eject Sensor does not detect paper within a predetermined time after scanning starts. The Duplex Eject Sensor keeps detecting paper within a predetermined time after 2-Sided Scanning. The Read Point Sensor keeps detecting paper in the ADF. The Read Point Sensor does not detect paper in the ADF. The paper remained in the ADF. The ADF does not go off after the predetermined time. Unexpected Jam timing (i.e. Original is too short, Ledger / A3 size original is fed without being recognized that the length is abnormal for a Fax Transmission, etc.)

Section A

A (i-ADF only)

A

129 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

3.1.3.

Mechanical Error Codes (E Code)

Code E1- 01

E1- 20

E1- 22

E1- 31

E1: Optical Unit Error Function Possible Cause(s) Abnormal Platen Glass 1. Home Position Sensor connector disconnected. Scanning 2. Home Position Sensor defective. 3. Scanner Motor connector disconnected. 4. Scanner Motor defective. 5. Scanning Mechanism defective. 6. SPC PCB connector disconnected. 7. SPC PCB defective. 8. PS defective. Laser Unit Horizontal 1. LSU connector disconnected. Synchronization 2. LSU defective. 3. SPC PCB connector disconnected. 4. SPC PCB defective. Polygon Motor Synchronization 1. Polygon Motor connector disconnected. 2. SPC PCB connector disconnected. 3. LSU connector disconnected. 4. Polygon Motor defective. 5. PS defective. 6. SPC PCB defective. Scanning Lamp 1. INV PCB connector disconnected. (Does not turn On) 2. INV PCB defective. 3. Scanning Lamp defective. 4. SPC PCB connector disconnected. 5. PS defective.

Code Function E2- 01 Lift Motor Rotation (1st Paper Tray)

E2- 02 Lift Motor Rotation (2nd Paper Tray) E2- 03 Lift Motor Rotation (3rd Paper Tray) E2- 04 Lift Motor Rotation (4th Paper Tray)

E2: Lift DC Motor Error Possible Cause(s) 1. Level Sensor connector disconnected. 2. Level Sensor defective. 3. Lift Mechanism defective. 4. Lift Motor connector disconnected. 5. Lift Motor defective. 6. SPC PCB connector disconnected. 7. SPC PCB defective. 8. PS defective. 1. Level Sensor connector disconnected. 2. Level Sensor defective. 3. Lift Mechanism defective. 4. Lift Motor connector disconnected. 5. Lift Motor defective. 6. SPC PCB connector disconnected. 7. SPC PCB defective. 8. CST2 PCB connector disconnected. 9. CST2 PCB defective. 10. CST3 PCB connector disconnected. 11. CST3 PCB defective. 12. PS defective.

130 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

E2: Lift DC Motor Error Code Function Possible Cause(s) E2- 10 System Console Drive Motor 1. Drive Mechanism defective. Rotation 2. Drive Motor connector disconnected. 3. Drive Motor defective. 4. CST2 PCB connector disconnected. 5. CST3 PCB connector disconnected. 6. CST3 PCB defective. 7. PS connector disconnected. 8. PS defective. 9. SPC PCB connector disconnected. 10. SPC PCB defective. E3: Development System Error Code Function Possible Cause(s) E3- 01 Toner Bottle Motor Rotation 1. Toner Bottle Motor connector disconnected. 2. Toner Bottle Motor defective. 3. Toner Bottle Motor Drive Mechanism defective. 4. Toner Bottle installed incorrectly. 5. SPC PCB connector disconnected. 6. SPC PCB defective. 7. Toner Bottle Home Position Sensor connector disconnected. 8. Toner Bottle Home Position Sensor defective. 1. Toner Screw Motor defective. E3- 02 Toner Screw Motor Over 2. Toner Screw Motor Drive Mechanism defective. Current 3. SPC PCB defective. E3- 03 Toner Density Sensor Gain 1. Sensor connector disconnected. 2. Sensor defective. 3. SPC PCB connector disconnected. 4. SPC PCB defective. E3- 10 High Voltage Power Supply 1. PS connector disconnected. leak (1) - Grid Charge Voltage 2. PS defective. 3. SPC PCB connector disconnected. 4. SPC PCB defective. 5. Corona Wire is abnormal. (Check for: contamination with foreign particles, broken, not installed in the proper position, or loose tension) E3- 20 Main Motor Rotation 1. Drive Mechanism defective. 2. Main Motor connector disconnected. 3. Main Motor defective. 4. SPC PCB connector disconnected. 5. SPC PCB defective. 6. PS defective.

131 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Code E4- 01

E4- 02

E4- 10

E4: Fuser Unit Error Function Possible Cause(s) Fuser Warm-up Temperature 1. Fuser Thermistor dirty. 2. Thermistor position incorrect. 3. Thermistor defective. 4. Thermistor connector disconnected. 5. Fuser Lamp connector disconnected. 6. Fuser Lamp defective. 7. Fuser Thermostat defective. 8. Thermal Fuse defective. 9. SPC PCB connector disconnected. 10. SPC PCB defective. 11. Fuser temperature low. (Adjust F6-31) 12. Incorrect SC PCB is installed. 13. Incorrect SPC PCB is installed. Fuser Paper Jam 1. Paper Jam in Fuser Unit. 2. Paper Exit Sensor disconnected. 3. Paper Exit Sensor defective. 4. SPC PCB connector disconnected. 5. SPC PCB defective. Fuser Fan Motor Rotation 1. Fuser Fan connector disconnected. 2. Fuser Fan defective. 3. SPC PCB connector disconnected. 4. SPC PCB defective. 5. PS defective.

E5: System Error Code Function E5- 11 Printer Engine Communication Abnormal E5- 17 Scanner Synchronization E5- 19 Scanner Line Synchronization E5- 40 Sort Memory Abnormal

E5- 42 Total Counter Connection

E5- 60 Power Supply Cooling Fan Motor Rotation

Possible Cause(s) 1. SPC PCB connector disconnected. 2. SPC PCB defective. 3. SC PCB connector disconnected. 4. SC PCB defective. 1. Sort Memory defective. 2. SC PCB connector disconnected. 3. SC PCB defective. 1. Total Counter connector disconnected. 2. Total Counter defective. 3. SPC PCB connector disconnected. 4. SPC PCB defective. 1. Cooling Fan connector disconnected. 2. Cooling Fan defective. 3. SPC PCB connector disconnected. 4. SPC PCB defective. 5. PS defective.

E7: Optional Unit Error Code Function E7- 90 Hardware Key Abnormal

Check Points 1. Incorrect Hardware Key installed. 2. Hardware Key defective.

132 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

E13: Out of Toner Code Function E13 No Toner Detection

3.1.4.

Possible Cause(s) 1. Out of Toner. 2. Toner Bottle not installed. 3. Toner Bottle not installed correctly. 4. Toner Sensor disconnected. 5. Toner Sensor defective. 6. SPC PCB connector disconnected. 7. SPC PCB defective.

Technician Warning

The following message will be displayed in the event. LCD Message HDD OPTION REQUIRES ADDITIONAL SORT MEM

MACHINE ID ERROR

Possible Cause(s) 1. Additional Sort memory is not installed. • DA-SM16 (16 MB) • DA-SM64 (64 MB) • DA-SM28 (128 MB) 2. Make sure the SDRM PC Board was installed properly. 1. Incorrect SC PCB is installed. • SC PCB for DP-8020E • SC PCB for DP-8020P • SC PCB for DP-8016P 2. SPC PCB defective.

133 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

3.2.

Information Codes Table (For Facsimile) Fax Information Codes Phase Description of Problem Possible Cause(s) C, D The length of the received document is over 2 m. B Read Point Sensor does not Document not set properly. activate within 10 seconds after Defective Read Point Sensor. the document starts feeding. C Transmitting document was longer Document may be jammed. than 2,000 mm (78.7 in). Defective Read Point Sensor. (Super Fine: 1,000 mm (39.4 in), 600 dpi: 430 mm (16.2 in)) A ADF Door is open. Cover not firmly closed. Connectors not firmly connected. C Decoding process did not Defective FXB PCB. complete at the end of phase C. A-E Interface error occurred between Modem defective. (FXB PCB) the CPU, and modem. Software problem occurred. (SC PCB) System fault. Software problem occurred. (SC PCB)

Code 012

Mode RCV

030

XMT

031

XMT COPY

061

-

200

RCV

212

331

XMT RCV XMT RCV XMT

400

XMT

B

401

XMT

B

DCN was returned from receiver while transmitter is waiting for CFR, or FTT.

402

XMT

B

403

RCV (Polling)

B

DCN was returned from receiver while transmitter is waiting for NSF/DIS. Transmitter had no polling function.

404

XMT

B

301

C

8-minutes timer error. (Germany only) T1 timer (35±5 sec) elapsed without detecting 300 bps signal.

Transmitter sent NSS (or DCS) followed by TCF three times, but the receiver did not respond. (CFR, or FTT is usually returned)

Wrong number dialed, and the START button was pushed. Telephone line disconnected while dialing. FXB PCB (Modem), or MJR PCB defective. Receiver defective. (It may only be transmitting CED) Your machine's ID Number is not programmed. Possible incompatibility, or incorrect Password (Password Reception, Selective Receive). Mailbox full. Receiver working in non-CCITT mode only. (Possible incompatibility) "POLLED=ON" (polling XMT ready) not set at the transmitter. Document to be transmitted not placed at the transmitter. Receiver defective. (Modem, MJR PCB, etc.) FXB PCB, or MJR PCB defective. Receiver disconnects line during first NSS (or DCS) transmitted.

134 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Code 405

Mode XMT

406

RCV (Password Comm.)

407

XMT

408

XMT

409

XMT

410

RCV

411

RCV (Polling)

412

G3 RX

414

RCV (Polling)

415

XMT (Polling)

416

RCV

417

RCV

Fax Information Codes Phase Description of Problem Possible Cause(s) B Transmitter received FTT after it Line quality poor. (TCF is damaged due transmitted TCF at 2400 bps. to line noise) Received RTN after Receiver defective. (Modem, MJR PCB, communicating at 2400 bps. etc.) FXB PCB, or MJR PCB defective. B XMT-Password mismatched. RCV- XMT, RCV password does not match. Password mismatched. Selective Last 4 digits of TSI does not match with RCV incomplete. the last 4 digits of Auto Dial telephone number. D Transmitter received no response Receiver defective. (No paper, paper after it transmitted post message, jamming, etc.) such as EOP, MPS, EOM, etc...or Receiver ceased receiving because of received DCN. excessive errors. (Line quality poor) FXB PCB (Modem), or MJR PCB defective. D Transmitter received RTN after it Receiver receives data with errors. transmitted EOP, MPS, or EOM. (Line quality poor) Receiver defective. (Modem, MJR PCB, etc.) FXB PCB, or MJR PCB defective. D Transmitter receives PIN after it Receiver receives data with error due to transmitted a post message, such poor line quality, and receiving operator as EOP, MPS, EOM, etc. requests voice contact. Receiver defective. (Modem, MJR PCB, etc.) FXB PCB, or MJR PCB defective. D Received DCN while waiting for Interface, or line faulty. post command. (EOP, MPS, EOM, Transmitter defective. etc.) B Received DCN after transmitting Transmitter not ready for polling NSC. communication. Password does not match between transmitter, and receiver. B, D No response within 12 seconds in Transmitter defective. NSS/DCS/MPS wait state. (After FXB PCB defective. transmitting FTT) B No response received after Password does not match between transmitting 3rd NSC. transmitter, and receiver. Transmitter defective. (No original, document jam, etc.) B Remote side attempted to receive Inform the remote side that your message from your machine in machine does not have the polling polling communication. transmission feature. D Receiver did not detect post Transmitter defective. command, such as EOP, MPS, Line quality poor. (RTC signal distorted EOM, etc. due to line noise) FXB PCB, or MJR PCB defective. C Receiver returned RTN in Line quality poor. (There are excessive response to post message. errors in received data) FXB PCB, or MJR PCB defective.

135 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Code 418

Mode RCV

420

RCV

421

RCV

422

XMT

427

G3 RCV XMT RCV XMT, or RCV

433 434

Fax Information Codes Phase Description of Problem Possible Cause(s) C Receiver transmitted PIN in Line quality poor. (There are excessive response to PRI-Q from errors in received data) transmitter. (Transmitting operator FXB PCB, or MJR PCB defective. requests voice contact) B T1 timer (35 sec.) elapsed without Wrong number dialed. detecting 300 bps signal. (Non-facsimile communication) Transmitter defective. FXB PCB, or MJR PCB defective. B Busy Tone was detected after Remote station disconnected the line. sending NSF Signal. Wrong number was dialed. B Content of NSF (or DIS), or NSC Incompatible content (or DTC) was invalid. B DCN received to NSF/CSI/DIS Interface is incompatible. transmitted. B, D T.30 Protocol abnormal. Defective remote station. B

436

G3 RX

C

456

RCV

B

457 RELAY XMT CONF. XMT/ POLL 459 RCV

C

490

RCV

C

494

RCV

C

495

XMT RCV

496

XMT

501

XMT/ RCV(V.34) XMT/ RCV(V.34)

502

B

CD (response from Modem) did not turn OFF within 180 sec. after receiver detected FLAG signal. DCN received after transmitting FTT. Received relay transfer request, or confidential document to distribute to an end receiving station, or all confidential mailboxes are used. Remote unit does not have Relayed XMT, or Confidential Comm. capability. Failed training in Phase C.

Sum of error lines exceeded the limit (Function Parameter No. 70) of 64 lines. Interval between two EOLs was more than 10 sec. when receiver received message data.

Remote unit defective. FXB PCB, or MJR PCB defective. Transmitter defective, or incompatible. Line quality poor.

Line quality poor. (Training signal distorted due to line noise) FXB PCB, or MJR PCB defective. Line quality poor. FXB PCB, or MJR PCB defective.

Transmitter defective. Line quality poor. (EOL damaged due to line noise) FXB PCB, or MJR PCB defective. C During reception, CD turned OFF, Line disconnected. or continued ON for long time. Transmitter defective. During communication, lost loop - FXB PCB, or MJR PCB defective. current. C CS of modem is not able to turn FXB PCB defective. ON. B Incompatible Modem on the Remote unit. B, C, D During reception, CD turned OFF, Line disconnected. or continued ON for long time. Transmitter defective. During communication, lost loop - FXB PCB, or MJR PCB defective. current.

136 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Code 503

Fax Information Codes Phase Description of Problem Possible Cause(s) B, C, D CS of modem is not able to turn FXB PCB defective. ON during training. Line disconnected. B Polling is rejected from the remote No polling original set. station. B Polling XMT is rejected. No polling original set.

540

Mode XMT/ RCV(V.34) RCV/V.34 (Polling) XMT/V.34 (Polling) XMT ECM

541

XMT ECM

D

542

XMT ECM

D

543

XMT ECM

D

544

XMT ECM

D

550

RCV ECM

C

554

RCV ECM

D

555

RCV ECM

D

570

RCV

B

571

XMT

B

580

XMT

B

581

XMT

B

582

XMT

B

601

XMT

623

XMT

A

630

XMT, or RCV (Polling)

B

Redial count over.

631

XMT

A

"STOP" key was pressed during Auto Dialing.

504 505

B

No response after transmitting 3rd CTC, or DCN received. No response after transmitting 3rd EOR, or received DCN. No response to the 3rd RR transmitted, or received DCN. T5 timer (60 sec.) elapsed without MCF. Stopped Transmission after EOR Transmission. Timer between frames in phase C has elapsed. Transmitted ERR after receiving EOR. Transmitted PIN after receiving EOR. Password, or machine code did not match during remote diagnostic communication. Remote unit did not have the remote diagnostic function. Sub-address transmission to a unit that has their DIS bit 49 (NSF bit 155) OFF. Sub-address Password transmission to a unit that has their DIS bit 50 (NSF bit 156) OFF. Sub-address SEP (for Polling) transmission to a unit that has their DIS bit 47 (NSF bit 130) OFF. ADF Door was opened during ADF transmission. No original was in the ADF. (Builtin dialer engaged)

Incompatible interface. Faulty line. MJR PCB abnormal. Remote unit abnormal. Remote unit abnormal. Faulty line. MJR PCB abnormal. Defective remote station. Faulty line. Faulty line, and Operator Call requested by RX side.

Sub-address transmission to a unit that has no Sub-address function. Sub-address transmission to a unit that has no Sub-address function. Sub-address transmission to a unit that has no Sub-address function.

Operator removed the original from the ADF after dialing was completed. Original was not set properly in the ADF. No dial tone detected. Sensor did not detect dial tone. (Country dependent) Busy tone is detected. (Country dependent) T1 timer (35±5 sec) elapsed without a signal from the receiver.

137 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Code 634

Mode XMT

Phase PSTN

638

XMT

PSTN LAN

700

XMT RCV XMT

PSTN LAN LAN

714

XMT RCV

LAN

715

XMT

LAN

716

XMT

LAN

717

XMT

LAN

718

XMT

LAN

719

RCV

LAN

720

POP

LAN

721 722

POP RCV

LAN LAN

725

XMT POP XMT POP

LAN

712

726

LAN

Fax Information Codes Description of Problem Possible Cause(s) Redial count over with no response, or busy tone was not detected. Note: U.S.A., and Canadian models will redial only once if a busy tone is not detected. Power turned Off with applicable Power switched Off. data in memory, or during Power failure occurred. communication. Communication terminated by Operator pressing the "STOP" key. Unknown email address replied Mail Server received an incorrect email from the Mail Server. address. (Dependent on Server's Mail application) LAN Interface error. The 10Base-T/100Base-TX cable not Cannot logon to the LAN. connected. An unexpected LAN problem occurred. TCP/IP connection timed out. Incorrect IP Address set. Verify the IP Address, Default Router IP Address, SMTP Server IP Address. Cannot logon to the LAN. Incorrect SMTP Server IP Address set. No email application activated on the Mail Server. Incomplete SMTP Protocol Mail Server’s hard disk may be full. transmission. Mail Server defective. Page Memory Overflow occurred Check the document size, and while receiving printing data. The resolution. paper size selected within your Ask originator to resend in a supported application to print is larger than size, and resolution. the paper size loaded in the paper tray(s). Received data via LAN is in a Ask the originator to resend with a format that is not supported. supported file attachment: * In a TIFF-F format. * Image data conforming to A4/Letter size. Unable to connect to the POP Incorrect POP Server address set. Server. POP Server is down. Unable to login to the POP Server. Incorrect User Name, or Password set. Failed to obtain the Network DHCP not available. Parameters (such as: IP Address, (Contact the Network Administrator.) Subnet Mask, Default Gateway IP Address, etc.) from the DHCP server. DNS Server connection timed out. Incorrect DNS Server address set. DNS Server is down. Received an error response from Incorrect POP Server address set. the DNS Server. Incorrect SMTP Server address set.

138 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Code 727

Mode XMT

Phase LAN

728

XMT

LAN

729

XMT

LAN

730

RCV

LAN

731

RCV

LAN

741 XMT, Polling PSTN

800

Relay Comm.

814

Conf. XMT Conf. Polling Relay Comm. 815 Conf. RCV 816 Conf. Polled 825 870 879

880 884 961 962

Conf. RCV Conf. Polled MEM XMT Multi-Copy Memory RCV

RCV XMT

PSTN

PSTN

Fax Information Codes Description of Problem Possible Cause(s) Received an Error, or No Remote Internet Fax Errors: Busy, or Response from the Remote Job Number Overflow for Relay XMT. Internet Fax. (SMTP Direct XMT) (Retry is possible) Remote Internet Fax Errors: Memory Overflow, or No Power. (Retry is not possible) Failed to authenticate (SMTP SMTP AUTHENTICATION, User Name, AUTHENTICATION) when and/or Password are incorrect. connecting with the SMTP server. (Contact the Network Administrator.) Unable to program the Internet Verify that the Fax Parameter #158 is parameters, or the autodialer via set to Valid. Email from a PC. Dialer full while Relayed Dial buffer for manual number dialing Transmission Request was (70 stations) is being used. received. Unable to dial Deleted the registered station name before dialing with Timer Controlled Communications, etc. The machine was requested to relay a document but has no Relay Hub capability. The remote station does not have Relay XMT nor Confidential Communication capability.

PSTN Mailbox full. PSTN The received Polling Password did not match. PSTN Parameter settings of the remote station are not properly set. PSTN Memory overflow occurred while LAN storing documents into memory. PSTN Memory overflow occurred during substitute memory reception. LAN Memory overflow. Mail Server sent a reset command while downloading the data to the machine. File Access Error. File Access Error. LAN Memory file access error. PSTN Memory file access error. LAN Memory file access error.

Memory overflow on the Fax side. Memory overflow on the Fax side. Mail server aborted the download (Busy with other higher priority jobs).

SC PCB defective. SC PCB defective. SC PCB defective.

139 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

memo

140 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

4 Service Modes 4.1.

Service Modes (For Copier)

These Service Modes are provided to assist the technician in checking for abnormalities in the copier, and a means of making adjustments to the Input/Output of major components. Caution: The factory default parameters are preset (destination dependent) for optimum performance, and in compliance with the local telecommunication regulations/standards, and do not need to be changed. Changing some of these parameters may cause the unit to be no longer compliant, or become inoperable.

4.1.1.

Service Mode Procedure

1. To select the Service Mode The service mode is selected when “FUNCTION”, “ORIGINAL SIZE”, and “3” keys are sequentially pressed, then F1 will appear in the display. 2. To exit the Service Mode The service mode is reset when the “FUNCTION”, and “CLEAR” keys are pressed simultaneously.

4.1.2.

Copier Service Mode Functions Service Modes (For Copier)

Service Mode F1 Self Test

Item

Function

00 CCD Test 01 LCD/LED Test

This test is used for checking the CCD. This test is used for checking the LCD, and LEDs. This test is used for checking the Page Memory. Prints the pattern for setting the Paper position alignment. Prints the Slant pattern for setting the Paper position alignment. Prints the Grid pattern for setting the Paper position alignment. Prints the pattern for setting the Duplex Paper position alignment. One sheet is copied when the Start key is pressed. Multi copies are made when the Start key is pressed. The functioning of Input / Output items (selected item numbers) is checked. Various function settings (selected by code numbers) can be changed. Various function settings (selected by code numbers) can be adjusted. Electronic Counters for Maintenance Perform pseudo-operation of an item (selected by code numbers)

02 Page Memory Test 03 Print Test Pattern 1 04 Print Test Pattern 2 05 Print Test Pattern 3 06 Print Test Pattern 4 F2

Single Copy Test

F3

Continuous Copy Test

F4

Input / Output Status Test

F5

Function Parameters

F6

Adjust Parameters

F7 F8

Electronic Counter Service Adjustment

141 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Service Modes (For Copier) Service Mode F9 Unit Maintenance

Item

Function Fax Service Mode Service Alert Tel # Firmware Version Print Device Info.

F5 / F6 Information List (Sample) **********-F5/F6 INFORMATION LIST-****** DATE MMM-dd-yyyy *** TIME12:01 *** P.01

F5-00 F5-01 F5-02 F5-03 F5-04 F5-05 F5-06 F5-07 F5-08 F5-09

. . . . . Frequency desired . . . . . LSU startup speed LSU off timer . . . . . . . . . . . . . . . . . . . . Fuser lamp control

F5-10 F5-11 F5-12 F5-13 F5-14 F5-15 F5-16 F5-17 F5-18 F5-19

EXIT TRAY LIMITATION REPLACE DRUM UNIT Printer fan extension PAPER OUT INDICATOR Paper size (tray1) Paper size (tray2) Paper size (tray3) Paper size (tray4) . . . . . T Corona Current Adj

F5-20 ADF

F5-50 F5-51 F5-52 F5-53 F5-54 F5-55 F5-56 F5-57 F5-58 F5-59

Auto contrast adj. Dept. Counter (COPY) Dept. Counter (FAX) 2-sided auto shift Margin reduction Margin value default Edge value default Book value default U14 Clear Oper.add toner alarm

Yes Yes No No No 10mm 5mm 20mm Any Keys Stop

Auto Tray selection TDC Adj.(Dev Cond.) TDC Adj.(Dev Life) U13 clear Dept. Counter (SCAN) Dept. Counter (PRINT) . . . . . . . . . . . . . . . Reduce N in 1 space

Yes Yes Yes Any keys Yes Yes

No

F5-60 F5-61 F5-62 F5-63 F5-64 F5-65 F5-66 F5-67 F5-68 F5-69

Auto

F5-70 PM cycle

60Hz Full 15 Sec.

Auto None Off 5 min On LETTER LEDGER LEDGER LEDGER

No 120k

**********-F5/F6 INFORMATION LIST-****** DATE MMM-dd-yyyy *** TIME12:01 *** P.02 F6-00 F6-01 F6-02 F6-03 F6-04 F6-05 F6-06 F6-07 F6-08 F6-09

Adj 100% Read (S/S) Adj 100% Read (L/T) 100% Selection Orig. Registration Printer Registration Main Motor Speed Polygon Motor Speed Registration Void Trail Edge Read Tim. Trail Edge Prt Tim.

0 0 0 0 0 0 0 6 0 -6

F6-50 F6-51 F6-52 F6-53 F6-54 F6-55 F6-56 F6-57 F6-58 F6-59

T/P Mode Image Density Photo Image Density . . . . . CCD Read Position Text Mode Contrast T/P Mode Contrast Photo Mode Contrast . . . . . Corona Charger Curr. Trail Edge(Trays)

0 0

F6-10 F6-11 F6-12 F6-13 F6-14 F6-15 F6-16 F6-17 F6-18 F6-19

Side Adjust (Bypass) Side Adjust (Tray 1) Side Adjust (Tray 2) Side Adjust (Tray 3) Side Adjust (Tray 4) . . . . . Side Adjust (ADU) Std Grid Voltage Standard Laser Power Bias Std Voltage

0 0 0 0 0

F6-60 F6-61 F6-62 F6-63 F6-64 F6-65 F6-66 F6-67 F6-68 F6-69

Trail Edge(Bypass) Trail Edge(2-Side) TDC Gain Voltage Adj Lead Edge Read Tim. Side Edge Read Adj. Trans Side1(S-Wide) Trans Side2(S-Wide) ADF Image Density . . . . . Stamp Position Adj.

0 0 0 0 0 0 0 0

F6-20 . . . . . F6-21 TDC Gain Voltage F6-22 . . . . .

0 0 0 0

0

F6-70 . . . . . F6-71 ADF Read Scan Pos. F6-72 Original Lead ADF:S

0 0 0 0 0 0

0

0 0

142 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Machine Setup Information List (Sample) **********- M A C H I N E S E T U P I N F O R M A T I O N -****** DATE MMM-dd-yyyy *** TIME12:01 *** P.01 1.MACHINE INFORMATION MACHINE NAME MAC ADDRESS SERIAL NUMBER

: DP-8020E : 080023006FA1 :

2.FIRMWARE VERSION SC SC BOOT PNL SPC FAX MODEM PDL FONT1 SC2

: : : : : : :

3.MEMORY CAPACITY PAGE MEMORY SORT MEMORY FAX MEMORY

: 32 MB : 16 MB : 2 MB

4.OPTION DOCUMENT FEEDER (ADF) 2nd PAPER TRAY 3rd PAPER TRAY 4th PAPER TRAY FAX BOARD NETWORK SCANNER PCL PRINTER PS PRINTER EMAIL HDD KEYBOARD

: : : : : : : : : : :

5.ERROR LOG TOTAL PRINT COUNT

: 2082

AAV10xxxPU LLN4 VO2000x 20E V10xxx

ADF Yes Yes Yes Yes Yes No No Yes No Yes

NO. DATE & TIME ERROR CODE ERROR COUNT NO. DATE & TIME ERROR CODE ERROR COUNT -------------------------------------------------------------------------------01 MMM-dd-yyyy 11:11 J27 XX-00000008 02 MMM-dd-yyyy 11:31 J41 XX-00000140 (See Remarks) --------------------------------------------------------------------------------

-PANASONIC ****************************** -PANASONIC

- ***** -

0001- ********

Remarks: XX-00000140

Page Count 00 : Printer Error 02 : Scanner Error

143 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

F7 Total Counter List (Sample) **********-F7 TOTAL COUNTER LIST-****** DATE MMM-dd-yyyy *** TIME12:01 *** P.01 F7-01 Key Operator ID Code

:

000

F7-02 F7-03 F7-04 F7-05 F7-06 F7-07 F7-08 F7-09 F7-10

Total Count PM Count Scanner PM Count . . . . . OPC Drum Count Process Unit Count ADF/i-ADF PM Count . . . . . Developer Count

: : : : : : : : :

295 295 61

F7-11 F7-12 F7-13 F7-14 F7-15 F7-16 F7-29 F7-30 F7-31 F7-32

Sheet Bypass Count 1st Paper Tray Count 2nd Paper Tray Count 3rd Paper Tray Count 4th Paper Tray Count 2-Sided Count A4/LETTER Count A4-R/LETTER-R Count A3/LEDGER Count B4/LEGAL Count

: : : : : : : : : :

147 90 0 0 0 28 284 73 19 0

F7-17 F7-18 F7-19 F7-20

ADF/i-ADF Count ADF/i-ADF Read Count Scanner Count Scanner Read Count

: : : :

26 26 61 18

F7-21 COPY PRINT COUNT F7-22 COPY SCAN COUNT

: :

42 29

F7-23 PC PRINT COUNT F7-24 PC SCAN COUNT

: :

0 0

F7-25 FAX TRANSMIT COUNT F7-26 FAX RECEIVE COUNT F7-27 FAX PRINT COUNT

: : :

0 0 0

295 295 50 295

144 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

4.1.3.

F4 Mode: Input/Output Status Test

Set the machine to service mode, and press "4" key on the Keypad. ↓ Press the "START" key. ↓ Enter the number to activate the test then press "START" key. ↓ Press "STOP" key to cancel the test. ↓ When the “CLEAR” key is pressed, the selected code input will not be accepted. ↓ Press “FUNCTION”, and “CLEAR” keys simultaneously to exit the service mode. 1. Check Input

No.

Function

000 Toner Screw Motor Over Current Power Supply Fan Signal 003 Paper Tray Unit Option Detection Sensor (2nd Paper Tray) Paper Tray Detection Sensor (2nd Paper Tray) Paper Tray Detection Sensor (1st Paper Tray) NP Sensor (Sheet Bypass) Paper Length Sensor (Sheet Bypass) Size Sensor (PC1) (Sheet Bypass) Size Sensor (PC2) (Sheet Bypass)

F4 Mode (Check Input) Message Display Condition 7 6 5 4 3 2 1 0 Over Current is 1 detected. Normal. 0 Unit is installed. 0

Paper Tray is opened.

Paper Tray is opened.

Paper is not detected. Sensor is activated. Sensor is activated. Sensor is activated.

Remarks

0

0

1 1 1 1

145 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

No.

Function

004 Size Sensor (PC3) (Sheet Bypass) ADU Detection Sensor JAM Access Cover Open Detection Sensor (2nd Paper Tray) Upper Limit Sensor (2nd Paper Tray) Upper Limit Sensor (1st Paper Tray) NP Sensor (2nd Paper Tray) NP Sensor (1st Paper Tray) 005 Total Counter Detection Sensor Polygon Motor Lock Signal Main Motor Lock Signal Fuser Fan Lock Signal Toner Waste Container Detection Sensor Toner Waste Container Full Detection Sensor Toner Bottle Motor Rotation Detection Sensor 006 ADU Paper Sensor Fuser Exit Sensor Registration Sensor (2nd Paper Tray) Registration Sensor 008 Front / Left Cover Open Sensor 1

Developer Unit Detecting Sensor

F4 Mode (Check Input) Message Display Condition 7 6 5 4 3 2 1 0 Paper is not detected. 0 Unit is connected. Cover is open.

0 0

Upper Limit is detected.

1

Upper Limit is detected.

1

Paper is not detected.

0

Paper is not detected. Counter is not detected. Normal. Normal. Normal. Toner Waste Container is detected. Toner Waste Container is full. Lock Paper is detected. Paper is detected. Paper is detected. Paper is detected. See Remarks.

Unit is connected.

Remarks

0 1 0 0 0 0 1 0 0 0 0 0 *

Front / Left Cover is closed. Signal 1 = 0 Signal 2 = 0 Right Cover is open. Signal 1 = 1 Signal 2 = 1 1

146 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

No.

Function

009 JAM Access Cover Open Detection Sensor (4th Paper Tray) Paper Tray Detection Sensor (4th Paper Tray) Upper Limit Sensor (4th Paper Tray) Paper Tray Detection Sensor (4th Paper Tray) Feed Motor Lock Signal (3rd Paper Tray) Paper Tray Detection Sensor 2 (3rd Paper Tray) Paper Tray Detection Sensor 1 (3rd Paper Tray) 010 Registration Sensor (3rd Paper Tray) JAM Access Cover Open Detection Sensor (3rd Paper Tray) Paper Tray Detection Sensor (3rd Paper Tray) Upper Limit Sensor (3rd Paper Tray) NP Sensor (3rd Paper Tray) Registration Sensor (4th Paper Tray) NP Sensor (4th Paper Tray) 011 Corona Leak Detection

F4 Mode (Check Input) Message Display Condition 7 6 5 4 3 2 1 0 Cover is open. 0

Paper Tray is not connected.

Remarks

0

Upper Limit is detected.

0

Unit is connected.

0

Normal.

0

See Remarks.

*

See Remarks.

Unit is connected. Signal 1 = 1 Signal 2 = 0 A different signal pattern, indicates that the unit is not connected, or CST 3 PCB is defective.

*

Paper is detected. Cover is open.

0 0

Paper Tray is connected.

1

Upper Limit is detected.

0

Paper is not detected.

0

Paper is detected.

0

Paper is not detected. Leak

0 0

147 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

No.

Function

020 Size Sensor C (Not Used) Size Sensor B (Not Used) Size Sensor A (Not Used) Size Sensor Z (Not Used) Size Sensor Y (Not Used) Size Sensor X (Not Used) 021 Home Position Sensor ADF/Platen Cover Open Sensor ADF/Platen Cover Angle Sensor Fuser Lamp Disconnect Detection Sensor +24V Line Error Detecting Signal 030 ADF B1 Sensor ADF B2 Sensor ADF Paper Exit Detection Sensor ADF Inverting Cover Open Detection Sensor ADF Cover Open Detection Sensor ADF Detection Sensor 1

ADF Detection Sensor 2

031 ADF Original Sensor ADF Original Width Sensor ADF Original Width Sensor ADF Original Length Sensor 2 ADF Original Length Sensor 1

F4 Mode (Check Input) Message Display Condition 7 6 5 4 3 2 1 0 Original detected on the 1 C position. Original detected on the B position. Original detected on the 1 A position. Original detected on the 1 Z position. Original detected on the 1 Y position. Original detected on the 1 X position. Home position is 1 detected. ADF/Platen Cover is 1 open. ADF/Platen Cover is 1 open more than 30° angle. No Lighting +24V Line is ON.

Remarks Z

Platen

Y X C

B

A

Front Side

-

Original is detected. Original is detected. Original is detected.

1 1 1

Cover is open.

1

Cover is open.

1

See Remarks.

*

See Remarks.

iADF Signal 1 = 1 Signal 2 = 1 ADF Signal 1 = 1 Signal 2 = 0 A different signal pattern, indicates that the unit is not connected.

*

Original is detected. Original is detected. Original is detected. Original is detected. Original is detected.

1 1 1 1 1

148 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

2. Check Output Press the "START" key to start, and press the "STOP" key to reset.

No. Item 040 Total Counter

041- Not Used 049 050 Main Motor

051 Toner Bottle Motor Rotation In Forward Direction

052 Toner Screw Motor

053 Power Supply Fan

054- Not Used 055 056 Fuser Fan 057- Not Used 060 061 Registration Clutch

062 Not Used 063 Paper Feed Roller Clutch (1st Paper Tray) 064 Lift Motor (1st Paper Tray)

065 ADU Solenoid

066- Not Used 069 070 Paper Feed Roller Clutch (2nd Paper Tray) 071 Lift Motor (2nd Paper Tray)

F4 Mode (Output Check) Function When SPC PCB CN715-8 signal level changes to 0V from +24V, count up the Total Counter.

Remark

When SPC PCB CN723-2 signal level changes to 0V from +5V, the Main Motor activates. When SPC PCB CN720-16 signal level changes to 0V from +24V, the Motor rotates in the forward direction. When SPC PCB CN720-18 signal level changes to 0V from +24V, the Clutch activates. When SPC PCB CN704-9,10, CN709-16 are 24V, Power Supply Fan rotates high-speed.

When SPC PCB CN709-13 is 24V, Fuser Fan rotates.

When SPC PCB CN715-2 signal level changes to 0V from +24V, clutch operates.

1 minute

When SPC PCB CN715-4 signal level changes to 0V from +24V, clutch operates. When SPC PCB CN706-2 signal level changes to 0V from +24V, motor rotates in the ascending direction. When SPC PCB CN728-2 signal level changes to 0V from +24V, solenoid operates.

1 minute

When CST2 PCB CN773-2 signal level changes to 0V from +24V, clutch operates. When CST2 PCB CN774-2 signal level changes to 0V from +24V, motor rotates in the ascending direction.

1 minute

1 minute

149 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

No. Item 072 Intermediate Roller Clutch (2nd Paper Tray) 073- Not Used 074 075 Paper Feed Motor (3rd Paper Tray) 076 Paper Feed Roller Clutch (3rd Paper Tray) 077 Lift Motor (3rd Paper Tray)

078 Intermediate Roller Clutch (3rd Paper Tray) 079 Not Used 080 Paper Feed Roller Clutch (4th Paper Tray) 081 Lift Motor (4th Paper Tray)

082 Intermediate Roller Clutch (4th Paper Tray) 083- Not Used 084 085 Paper Feed Roller Solenoid (Sheet Bypass) 086- Not Used 119 120 Lamp

121- Not Used 159 160 ADF Paper Feed Motor Rotating (35% speed rotating) 161 ADF Paper Feed Motor Rotating (100% speed rotating) 162 ADF Paper Feed Motor Rotating (200% speed rotating) 163 ADF Paper Feed Motor Reverse Rotating (35% speed rotating)

F4 Mode (Output Check) Function When CST2 PCB CN773-4 signal level changes to 0V from +24V, clutch operates.

When CST3 PCB CN805-4 signal level changes to 0V from +5V, activate the Motor. When CST3 PCB CN806-2 signal level changes to 0V from +24V, clutch operates. When CST3 PCB CN804-2 signal level changes to 0V from +24V, motor rotates in the ascending direction. When CST3 PCB CN806-4 signal level changes to 0V from +24V, clutch operates.

Remark 1 minute

1 minute

1 minute

When CST2 PCB CN773-2 signal level changes to 0V from +24V, clutch operates. When CST2 PCB CN774-2 signal level changes to 0V from +24V, motor rotates in the ascending direction. When CST2 PCB CN773-4 signal level changes to 0V from +24V, clutch operates.

1 minute

When SPC PCB CN715-6 signal level changes to 0V from +24V, solenoid operates.

1 minute

1 minute

When SPC PCB CN656-3 signal level changes to +5V from 0V, Lamp operates.

ADF paper feed motor rotates at 35% speed. ADF paper feed motor rotates at 100% speed. ADF paper feed motor rotates at 200% speed. ADF paper feed motor rotates in reverse at 35% speed.

150 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

No. 164

165

166

167

168

169

F4 Mode (Output Check) Item Function ADF Paper Feed Motor Reverse ADF paper feed motor rotates in Rotating reverse at 100% speed. (100% speed rotating) ADF Paper Feed Motor Reverse ADF paper feed motor rotates in Rotating reverse at 200% speed. (200% speed rotating) ADF Paper Feed Roller Clutch 1 When ADF PCB CN22-10 signal level changes to 0V from +24V, clutch operates for 3 seconds. ADF Paper Feed Roller Clutch 2 When ADF PCB CN22-8 signal level changes to 0V from +24V, clutch operates for 3 seconds. ADF Paper Feed Roller Clutch 3 When ADF PCB CN24-2 signal level changes to 0V from +24V, clutch operates for 3 seconds. ADF Paper Exit Solenoid When ADF PCB CN26-2 signal level changes to 0V from +24V, Solenoid operates for 3 second. Not Used

170171 172 ADF Solenoid

173 ADF Inverting Solenoid

174 ADF Pinch Roller Solenoid

175 ADF Stamp Solenoid

Remark

When ADF PCB CN26-5 signal level changes to 0V from +24V, Solenoid operates for 1 second. When ADF PCB CN26-3 signal level changes to 0V from +24V, Solenoid operates for 1 second. When ADF PCB CN26-7 signal level changes to 0V from +24V, Solenoid operates for 1 second. When ADF PCB CN25-2 signal level changes to 0V from +24V, Solenoid operates for 1 second.

151 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

4.1.4.

F5 Mode: Function Parameters (For Copier)

Set the machine to Service Mode, and press "5" key on the Keypad. ↓ Press the "START" key. ↓ Enter the desired code number, or press “V”, ”/\” arrow keys. ↓ If you wish to select another code number, scroll the menu with the arrow keys. ↓ Press the "SET" key. ↓ Enter the desired function code number, and press “SET” key. ↓ When the “CLEAR” key is pressed, the selected code input will not be accepted. ↓ Press “STOP” key, then press “FUNCTION”, and “CLEAR” keys simultaneously to exit the service mode. ↓ Reboot the machine after setting the parameter(s) to activate the setting(s).

No. 00 01

F5 Mode Function

Item Not Used Frequency Desired

02 03

Not Used LSU Startup Speed

04

LSU Off Timer

05 06

Not Used Job Tracking Server

07-08 Not Used 09 Fuser Lamp Control 10

Exit Tray Limitation (Up to 250 Sheets)

11

Replace Drum Replace Drum (Except USA / Canada)

Default Setting

0 : Auto 1 : 50 Hz 2 : 60Hz

1 (for Europe)

0 : Low 1 : Full 1 : 5 sec. 2 : 10 sec. 3 : 15 sec. 4 : 20 sec. 6 : 30 sec. 8 : 40 sec. 10 : 50 sec. 12 : 60 sec.

1

0 : No 1 : Yes

0

0 : Off 1 : Auto 0 : None 1 : Accumulate 2 : Job 0 : Off 1 : On 0 : Off 1 : User (Displays Replace Drum) 2 : Service (Enables Check & Call function)

0 (for USA / Canada) 1 (for Europe) 0

2 (for USA / Canada)

3

0 0

152 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

No. 12

Item Printer Fan Extension

13

Paper Out Red Indicator

14

Paper Size Tray 1

15 16 17 18 19

Paper Size Tray 2 Paper Size Tray 3 Paper Size Tray 4 Not Used T Corona Current Auto Adj.

20

ADF

21 22

Not Used System Console

23-25 Not Used 26 2-Sided Unit 27-30 Not Used 31 ADF Duplex Scanning 32

Job Build, and SADF Mode

33

TH Sensor (Laser duty)

34-37 Not Used 38 2-Sided Mode Default

39

F5 Mode Function 0 : Non 2 : 2 min 5 : 5 min 0 : On 1 : Off 0 : None 1 : A3 2 : B4 3 : A4 4 : A4-R 5 : B5 6 : B5-R 7 : A5 8 : A5-R 9 : 8 x 13 10 : 8.5 x 13 11 : LEDGER 12 : LEGAL 13 : LETTER 14 : LETTER-R 15 : INVOICE Same as F5-14 Same as F5-14 Same as F5-14

Default Setting 5

0 1 (for Europe) 11 (for USA / Canada)

(for DP-8020E/8020P) (for DP-8020E/8020P)

0 : No 1 : Yes 0 : No 1 : Auto

1

0 : No 1 : Auto

1 (for DP-8020E/8020P)

0 : No 1 : Auto

1

0 : No 1 : Auto 0 : No 1 : Yes 0 : No 1 : Mid 2 : Large

1

0 : No 1 : 1 to 2 2 : 2 to 2 3 : B to 2

0

1

0 1

Not Used

153 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

No. 40

Item Double Count

41

Count Up Timing

42

KEY/DEPT. Counter

43 44 45

Key Counter Timing Not Used Dept Code Reentry Again

46 47

Not Used TH Sensor (T corona current)

48

TH Sensor (DEV)

49 50

Not Used Auto Contrast Adjust

51

Dept. Counter (COPY)

52

Dept. Counter (FAX)

53

2-Sided Auto Shift

54

Margin Reduction

55

Margin Value Default

56

Edge Value Default

57

Book Value Default

58

U14 Clear

59

Oper. Add Toner Alarm

F5 Mode Function 0 : No 1 : LDR 2 : LDR, LGL 3 : A3 4 : A3, B4 0 : At feed 1 : At exit 0 : No 1 : Key Cntr 2 : DEPT. 3 : Card Same as F5-41

Default Setting 1 (for USA / Canada) 3 (for Europe)

1 0

0

0 : Yes 1 : No

0

0 : No 1 : Mid 2 : Large 0 : No 1 : Mid 2 : Large

1

0 : No 1 : Yes 0 : No 1 : Yes 0 : No 1 : Yes 0 : No 1 : Auto sft 0 : No 1 : Yes 0 : 5 mm 1 : 10 mm 2 : 15 mm 3 : 20 mm 0 : 5 mm 1 : 10 mm 2 : 15 mm 3 : 20 mm 0 : 15 mm 1 : 20 mm 2 : 25 mm 3 : 30 mm 0 : Continue 1 : Any Keys 0 : Stop 1 : Continue

1

1

1 0 0 0 1

0

1

1 0

154 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

No. 60

Item Auto Tray Selection

61 62

TDC Auto Adj. (DEV Conditions) TDC Auto Adj.(DEV life)

63

U13 Clear

64

Dept. Counter (SCANNER)

65

Dept. Counter (PRINTER)

66-68 Not Used 69 Reduce N in 1 Space 70

PM Cycle

71

Add Toner Time Limit

72-75 Not Used 76 TH Sensor (Corona, Grid) 77

TH Sensor (Bias DC)

78

A4/LTR Size Select

79

Not Used

F5 Mode Function

Default Setting

0 : No 1 : Yes 0 : No 1 : Yes 0 : No 1 : Yes 0 : Any keys 1 : Func + 1 0 : No 1 : Yes 0 : No 1 : Yes

1

0 : No 1 : Yes 0 : No 1 : 1.5 K 2 : 2.5 K 3: 5K 4 : 10 K 5 : 15 K 6 : 20 K 7 : 30 K 8 : 40 K 9 : 60 K 10 : 80 K 11 : 90 K 12 : 120 K 13 : 150 K 14 : 200 K 15 : 240 K 0 : Unlimited 1 : 1/3 Limited 2 : 2/3 Limited

0

0 : No 1 : Yes 0 : No 1 : Yes 0 : No 1 : Yes

1

1 0 0 1 1

12

0

1 0

155 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

No. 80

Item Paper Size Priority

81

B4/FLS Size Selection

82

Manual Skyshot Mode

83

Digital Skyshot Mode

84

Paper Tray Priority

85

Side Void Setting (ADF)

86

PM Cycle (Optics)

87

PM Cycle (ADF)

88

USB Port Function

F5 Mode Function 1 : A3 2 : B4 3 : A4 4 : A4-R 5 : B5 6 : B5-R 7 : A5 8 : A5-R 9 : 8 x 13 10 : 8.5 x 13 11 : LEDGER 12 : LEGAL 13 : LETTER 14 : LETTER-R 15 : INVOICE 0 : B4 1 : 8 x 13 2 : 8.5 x 13 0 : Off 1 : M1, On 2 : M2, On 3 : M1, M2, On 0 : No 1 : Normal 2 : Quality 0:S>C>B 1:C>S>B 0 : None 1 : Yes 0 : No 1 : 40 K 2 : 60 K 3 : 120 K 4 : 240 K 5 : 360 K 6 : 480 K 7 : 600 K 0 : No 1 : 40 K 2 : 60 K 3 : 120 K 4 : 240 K 5 : 360 K 6 : 480 K 7 : 600 K 0 : Off 1 : Once 2 : ON

Default Setting 3 (for Europe) 13 (for USA / Canada)

0

0

1

1 0 0

0

0

156 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

No. 89

Item LAN Speed/Duplex

90

TCH Panel Beep Sound

91 92 93 94 95

M1, Size Y M1, Size X M2, Size Y M2, Size X Paper Size (FA)

96

Bypass Detection (FA)

97

BP Tray B4/FLS/LGL (FA)

98

TH Sensor (Laser Power)

99

Not Used

F5 Mode Function 0 : Auto 1 : 10 Half 2 : 10 Full 3 : 100 Half 4 : 100 Full 0 : Off 1 : Soft 2 : Loud Set the default size for Manual Skyshot Mode, M1, and M2.

(Factory use only)

0 : No 1 : Mid 2 : Large

Default Setting 0

1

160 70 220 95 1 (for USA / Canada) 2 (for Europe) 1 (for USA / Canada) 2 (for Europe) 0 (for Europe) 3 (for USA / Canada) 1

157 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

4.1.5.

F6 Mode: Adjust Parameters (For Copier)

Set the machine to Service Mode, and press "6" key on the Keypad. ↓ Press the "START" key. ↓ Enter the desired code number, or press “V”, ”/\” arrow keys. ↓ If you wish to select another code number, scroll the menu with the arrow keys. ↓ Press the "SET" key. ↓ Enter the desired function code number, and press “SET” key. ↓ When the “CLEAR” key is pressed, the selected code input will not be accepted. ↓ Press “STOP” key, then press “FUNCTION”, and “CLEAR” keys simultaneously to exit the service mode. ↓ Reboot the machine after setting the parameter(s) to activate the setting(s). Note: The Factory Setting is different in each model. F6 Mode No.

Item

00

Adj 100% Side-Side Read

01

Adj 100% Lead-Tail Read

02 03

100% Selection Original Registration

04

Printer Registration

05

Main Motor Speed

06 07

Polygon Motor Speed Registration Void

08

Trail Edge Read Timing

09

Trail Edge Print Timing

10

Side Adjust (Bypass)

11

Side Adjust (Tray 1)

12

Side Adjust (Tray 2)

13

Side Adjust (Tray 3)

Setting Range Adjustment for identical vertical (side-to-side) -9 - +9 0.1% size ratio. Adjustment for identical horizontal -9 - +9 0.1% (top-to-bottom) size ratio. Adjustment from 99.1% to 100.9% -9 - +9 0.1% Adjustment of platen original registration -30 - +30 detection timing. 0.2mm Delay time is adjusted from registration roller -50 - +50 clutch ON. 0.5mm Adjustment of Main Motor speed. -10 - +10 0.1% Adjustment Polygon Motor speed. -5 - +5 0.1% Registration void should be adjusted. 0 - +99 0.5mm Adjustment of trail edge void. -9 - 0 0.5mm Adjustment of trail edge void. -9 - +15 0.5mm Adjustment of LSU side-side (Sheet Bypass). -8 - +7 0.5mm Adjustment of LSU side-side (1st Tray). -8 - +7 0.5mm Adjustment of LSU side-side (2nd Tray). -8 - +7 0.5mm Adjustment of LSU side-side (3rd Tray). -8 - +7 0.5mm Remarks

158 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

F6 Mode No.

Item

14

Side Adjust (Tray 4)

Adjustment of LSU side-side (4th Tray).

15 16

Not Used Side Adjust (ADU)

Adjustment of LSU side-side (ADU).

17

Standard Grid Voltage

Charge voltage compensation adjustment.

18

Standard Laser Power

Laser power compensation adjustment.

19

Std Bias DC Voltage

Adjustment of bias standard voltage.

20 21

Not Used TDC Gain Voltage

22

DC Bias ON timing

Adjustment of toner density sensor gain voltage. (Factory use only)

23

DC Bias OFF timing

(Factory use only)

24-25 Not Used 26 TDC Judgment Level 27-29 Not Used 30 Light Halftone Adj. 31 Fuser Temperature

Remarks

Adjustment of toner supply starting judgement voltage level. Halftone duty ratio adjustment Adjustment of fuser temperature.

32

Fuser Edge Temperature

Temperature compensation for edges

33

TDC Max. Read Only

Set by F8-20 TDC Check Operation

34

TDC Min. Read Only

Set by F8-20 TDC Check Operation

35

TDC Avg. Read Only

Set by F8-20 TDC Check Operation

36 37 38

Paper Loop (Tray 1) Not Used F8-09 (TDC) Adjustment time

Individual Fine Adjustment for Tray 1 (Factory use only)

39 40

LSU Unit PWM Adjust Transfer Current Side 1

Adjustment of PWM value of LSU. Adjustment of Transfer Current.

41 42 43

Paper Loop (Bypass) Paper Loop (Tray 2) Paper Loop (2-Sided)

44

FAX Laser Duty Adj

Individual Fine Adjustment for Sheet Bypass Individual Fine Adjustment for Tray 2 Adjustment for the length of the loop formed before the copier timing roller. Printer Density Adjustment for FAX. (-) : Darker. (+) : Lighter.

45

Not Used

Setting Range -8 - +7 0.5mm -8 - +7 0.5mm -128 - +19 2.0V -19 - +38 0.05mW -128- +48 2.6V -70 - +57 0.033V -10 - +10 0.01Sec. -10 - +10 0.01Sec. -26 - +26 0.02V -127 - +127 -15 - +15 0.833°C -15 - +15 0.833°C -99 - +99 (Read only) -99 - +99 (Read only) -99 - +99 (Read only) -99 - +99 -1 - +5 60Sec. -32 - +32 -62 - +110 0.15uA -99 - +99 -99 - +99 -99 - +99 -99 - +99

159 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

F6 Mode No.

Item

Remarks

46

PRINTER Laser Duty Adj

47

Transfer Current Side 2

Printer Density Adjustment for Printer. (-) : Darker. (+) : Lighter. Adjustment of Transfer Current.

48

Transfer Current Envelope

Adjustment of Transfer Current.

49

T Mode Image Density

50

T/P Mode Image Density

51

P Mode Image Density

Image density adjustment for Text mode. (-) : Darker. (+) : Lighter. Image density adjustment for Text/ Photo mode. (-) : Darker. (+) : Lighter. Image density adjustment for Photo mode. (-) : Darker. (+) : Lighter.

52 53

Not Used CCD Read Position Adj

54 55 56 57 58

T Mode Contrast T/P Mode Contrast P Mode Contrast Not Used Corona Charger Current

Adjustment of Contrast for Text Mode. Adjustment of Contrast for Text/Photo Mode. Adjustment of Contrast for Photo Mode.

59

Trail Edge Trans (Trays)

60

Trail Edge Trans (Bypass)

61

Trail Edge Trans (2Sided)

62

TDC Gain Voltage Adjust

63

Lead Edge Read Timing (Adjustment for Double Exposure Copy Mode, for details, and adjustment procedure, refer to Sect. 2.9.8) Side Edge Read Adjust (Adjustment for Double Exposure Copy Mode, for details, and adjustment procedure, refer to Sect. 2.9.8) Transfer Current Side 1 (Small Width) Transfer Current Side 2 (Small Width)

Trail Edge Transfer Image High Voltage Timing Adjustment for Trays 1-4 feeding. Trail Edge Transfer Image High Voltage Timing Adjustment for Bypass Tray feeding. Trail Edge Transfer Image High Voltage Timing Adjustment for the 2nd side of 2-Sided printing. Adjustment of Toner Density sensor gain voltage. Adjustment of Lead Edge Read Point.

64

65 66

Adjustment of CCD read position.

Adjustment of Corona Charge Current.

Adjustment of Side Edge Read Point.

(Factory use only) Transfer Current (Not Use)

Setting Range -99 - +99

-62 - +110 0.15uA -62 - +110 0.15uA -99 - +99

-99 - +99

-99 - +99

-42 - +44 0.2mm -128 - +127 -128 - +127 -128 - +127 -77 - +76 1.3uA -30 - +30 0.5mm -30 - +30 0.5mm -30 - +30 0.5mm -10 - +10 0.033V 0 - +9 0.5mm

0 - +9 0.5mm

-20 - +20 0.15uA -20 - +20 0.15uA

160 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

F6 Mode No. 67 68 69

Item ADF Image Density Paper Loop (Tray 3) Stamp Position Adjust

70 71

Not Used ADF Read Main Scan Pos. (Reverse Side) 72 Original Lead Edge ADF (Reverse Side) 73 Original Trail Edge ADF (Reverse Side) 74 Stamp Position Adjust (Reverse Side) 75-76 Not Used 77 Add Toner Level

Remarks Compensation of ADF image density. Individual Fine Adjustment for Tray 3 Adjustment of verification stamp position.

Adjustment of ADF horizontal image read start position. Adjustment of ADF Original Lead Edge Adjustment of ADF Original Trail Edge Adjustment of Stamp Position

-99 - +99 0.05mm -99 - +99 0.3mm -127 - +127 0.3mm -50 - +50 0.3mm

Adjustment of Toner supply (Not Use)

-1 - +1 1 Individual Fine Adjustment for Tray 4 -99 - +99 Adjustment of Scanning Sharpness by digital -2 - +2 image processing for Text /Photo Copy Mode. 1 -99 - +99 (Read Only) -99 - +99 (Factory use only) (Read Only) -99 - +99 (Read Only) Value of Temperature sensor. 0 - 255 (Read Only) Value of Humidity sensor. 0 - 255 (Read Only)

78 79

Paper Loop (Tray 4) MTF Adjust

80

Laser Power Control

81

Grid voltage Control

82

Bias DC Voltage Control

83

Temperature Sensor Value

84

Humidity Sensor Value

85 86

Not Used ADF Reverse Stop Posi.

Adjustment of ADF reverse stop position.

87

ADF Exhaust Stop Posi.

Adjustment of ADF exit stop position

88-89 Not Used 90 ADF Image Read Start

Setting Range -99 - +99 -99 - +99 -50 - +50 0.3mm

91

Original Lead Edge ADF

Adjustment of ADF horizontal image read start position. Adjustment of original detection timing.

92

Original Trail Edge ADF

Adjustment of trail edge detection timing.

93

ADF 100% Image 1-Sided

Adjustment of magnification for 1-sided.

94

ADF 100% Image 2-Sided

Adjustment of magnification for 2-sided.

-99 - +99 0.3mm -99 - +99 0.3mm -99 - +99 0.05mm -99 - +99 0.3mm -127 - 127 0.3mm -9 - +9 0.1% -9 - +9 0.1%

95-96 Not Used 97 (Factory use only) 98 Not Used 161 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

F6 Mode No. 99

Item F5/F6 Initialization

Remarks

Setting Range

Initialize F5/F6 parameter settings.

162 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

4.1.6.

F7 Mode: Electronic Counter

Set the machine to Service Mode, and press "7" key on the Keypad. ↓ Press the "START" key. ↓ Enter the desired code number, or press “V”, ”/\” arrow keys. ↓ If you wish to select another code number, scroll the menu with the arrow keys. ↓ Press the "SET" key. ↓ Enter the desired function code number, and press “SET” key. ↓ When the “CLEAR” key is pressed, the selected code input will not be accepted. ↓ Press “STOP” key, then press “FUNCTION”, and “CLEAR” keys simultaneously to exit the service mode. ↓ Reboot the machine after setting the parameter(s) to activate the setting(s). F7 Mode No. 01

Item Key Operator ID Code

02 03 04 05 06

Total Count PM Count Scanner PM Count Not Used OPC Drum Count

07

Process Unit Count

08 09 10

ADF PM Count Not Used Developer Count

11 12 13 14 15 16 17 18 19 20 21 22 23 24

Sheet Bypass Count 1st Paper Tray Count 2nd Paper Tray Count 3rd Paper Tray Count 4th Paper Tray Count 2-sided Count ADF Count ADF Read Count Scanner Count Scanner Read Count Copy Print Count Copy Scan Count PC Print Count PC Scan Count

Remarks Key Operator’s identification code for access to the counter mode. Total count for all copies / prints. Preventive Maintenance count. PM count for scanner readings. PM count of recording paper fed through the OPC Drum. PM count of recording paper fed through the Process Unit. PM count of originals fed through the ADF. PM count of recording paper fed through the Developer. Total count of paper fed from the sheet bypass. Total count of paper fed from the 1st paper tray. Total count of paper fed from the 2nd paper tray. Total count of paper fed from the 3rd paper tray. Total count of paper fed from the 4th paper tray. Total count of 2-sided Print. Total count of originals fed through the ADF. Total count of originals scanned through the ADF. Total count of scanning operations. Total count of scanner readings. Total count of copies printed. Total count of copies scanned. Total count printed from PC. Total count scanned to PC. 163

Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

F7 Mode No. 25 26 27 28 29 30 31 32 99

Item Fax Transmit Count Fax Receive Count Fax Print Count Total OPC Rotation Time A4/LT Count A4R / LETTER R Count A3 / Ledger Count B4 / LEGAL Count All Counter Clear

Remarks Total count of Fax transmitted. Total count of Fax received. Total count of Fax printed. Total Time of OPC Rotation. Total count of A4 / Letter Print. Total count of A4-R / Letter-R Print. Total count of A3 / Ledger Print. Total count of B4 / Legal Print. All counters are cleared.

164 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

4.1.7.

F8 Mode: Service Adjustment

Set the machine to Service Mode, and press "8" key on the Keypad. ↓ Press the "START" key. ↓ Enter the desired code number, or press “V”, ”/\” arrow keys. ↓ If you wish to select another code number, scroll the menu with the arrow keys. ↓ Press the "SET" key. ↓ Enter the desired function code number, and press “SET” key. ↓ When the “CLEAR” key is pressed, the selected code input will not be accepted. ↓ Press “STOP” key, then press “FUNCTION”, and “CLEAR” keys simultaneously to exit the service mode. ↓ Reboot the machine after setting the parameter(s) to activate the setting(s). F8 Mode No. 00

Item Exp. Lamp Replacement

01-05 Not Used 06 Error Log Print/View

07

Error Log Clear

08 09 10 11 12

(Factory use only) Toner Density Adjustment Drum Charge Adjustment Not Used Org.size Sensor Adj. (Not Used)

13

Black Density Reference (Not Used) 14 OPC Counter Reset 15-17 Not Used 18 LSU PWM Pattern

Remarks When replacing the exposure lamp. Procedure: a) Press the Start key to move the exposure lamp to the position (approx. 250 mm from the optics home position) where it can be replaced. b) To return the optical system to the home position, press the CLEAR key.* a) Each time the arrow key is pressed, the machine errors, or paper jam codes stored in memory are displayed, beginning with the oldest code. Note: Only the 30 most recent codes are displayed. a) Press the Reset key. A Message "Error code can be cleared with the Start key" is displayed on the LCD.* b) Press the Start key. Lock operation for Scanner Unit. Adjustment operation of Toner Density. Adjustment operation of Drum Charge. Adjust the slice level for the original size detection sensors automatically. Execute this mode by closing the platen cover. Adjustment operation of Black Density sensor. Proceed when OPC is replaced. Print out the Test Pattern. Proceed when the LSU is replaced. 165

Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

F8 Mode No. 19

Item Move Mirror To Lock

20 21-46 47 48

TDC Check Operation Not Used ADF Continuous Test Platen Continuous Test

Remarks a) Press the Start key to move the mirror unit to the locked position for transporting the copier. b) When the mirror unit is locked, the machine will not accept any numerical key input. Note: The locking operation is automatically reset when the Power switch is turned ON again. Adjustment of TDC sensor. Press START key to begin. Press START key to begin.

166 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

4.1.8.

F9 Mode: Unit Maintenance

Set the machine to Service Mode, and press "9" key on the Keypad. ↓ Press the "START" key. ↓ Enter the desired code number, or press “V”, ”/\” arrow keys. ↓ If you wish to select another code number, scroll the menu with the arrow keys. ↓ Press the "SET" key. ↓ Enter the desired function code number, and press “SET” key. ↓ When the “CLEAR” key is pressed, the selected code input will not be accepted. ↓ Press “STOP” key, then press “FUNCTION”, and “CLEAR” keys simultaneously to exit the service mode. ↓ Reboot the machine after setting the parameter(s) to activate the setting(s). F9 Mode Service Item Mode F9 Unit 00 Fax Service Mode Maintenance 01 Service Alert Tel # 02 Firmware Version

Remarks

00 SC 01 SC Boot 02 03 04 05

PNL SPC Not Used FAX Modem

Displays the contact number when a machine malfunction occurs. Displays the firmware version for SC. Displays the firmware version for SC Boot. Displays the firmware version for PNL. Displays the firmware version for SPC. Displays the firmware version for FAX option 1.

06 Not Used 07 SC2 00 F5/F6 Parameters

Displays the firmware version for Slot 1. Prints the memory contents of the F5, 03 Print Device Info. and F6 modes. 01 Machine Information Prints the machine setup information list. 02 Counter Information Prints the Counter information list. 03 System Address Prints the system memory setting. Info. 04 RAM Address Prints the RAM data dump list. Information 04 RAM Edit 0 Relative Address Setting of Relative address. Mode 1 Absolute Address Setting of Real address. 05 Serial Number Registration of Serial Number for Maintenance. Clears by Shipment Set.

167 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

F9 Mode Service Item Mode F9 Unit 06 RAM 00 Parameter Initialize Maintenance Initialize

01 All Job Clear 02 LBP Error Log Clear 03 Shipment Set

07 Firmware Update

04 05 06 00

LBP Fuser Reset Dept. Counter Clear Flash Memory Clear Update FROM Card

01 Update from USB 08 Program Backup (Refer to Sect. 2.7.)

00 Main 01 Option 1 all 02 Option 1 a 03 Option 1 b 04 Not Used 05 Not Used 06 Not Used 09 Update Program Card

10 Program Copy

11 12 13 14

00 From card to slot 1 01 Not Used 02 From slot 1 to card 03 Not Used 04 Not Used 05 Not Used Parameter Backup Parameter Restore Page Memory Size Sort Memory Size

Remarks Resets the Fax, and Function parameters to default values. Note: Turn the Power Switch to the OFF, and back to the ON position to enable the parameter settings. Clears all Jobs stored in Flash Memory. Clears LBP Error log Clears All Jobs, All Preset Data, Parameter Initialize & Resets the Counters (Fax). Clears the LBP fuser error. Resets the Counter Clears the Flash Memory Data Updates the firmware in the machine with the Master Firmware Card. Updates the firmware in the machine with the USB. Onboard F-ROM 4MB Slot 1 FRM8 PCB 8MB Slot 1 FRM8 PCB 4MB (a) Slot 1 FRM8 PCB 4MB (b) Slot 2 FRM8 PCB 8MB Slot 2 FRM8 PCB 4MB (a) Slot 2 FRM8 PCB 4MB (b) Creates a Master Firmware Card using the Firmware Update Kit. A 4MB, or 8MB Flash Memory Card will be required depending upon the model. Configuration for Program copy.

Backup the Parameter. Restore the Parameter. Displays the page memory size (MB). Displays the sort memory size (MB).

168 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

4.2.

Service Modes (For Facsimile)

Caution: The factory default parameters are preset (destination dependent) for optimum performance, and in compliance with the local telecommunication regulations/standards, and do not need to be changed. Changing some of these parameters may cause the unit to be no longer compliant, or become inoperable.

4.2.1.

Fax Service Mode Procedure

1. To enter the Fax Service Mode a. Press “FAX/EMAIL” key. b. Press “FUNCTION”, and then “7” keys. c. Press “MONITOR” four times, then press “*”. d. Enter the desired code number, or press the “V”, ”/\” arrow keys. 2. To exit the Fax Service Mode Press “STOP” key. Note: The following buttons provide these functions in the Service Mode: "START": "V” "/\ “

4.2.2.

: : :

The new setting value is stored in the machine. Scroll the function parameter number down. Scroll the function parameter number up.

FAX Service Mode Table

The following service modes are provided to assist you in setting operational functions of the unit, and determining the condition of the unit.

No. Service Mode 00 Not Used 01 Function Parameter Setting 02 03

RAM Edit Mode Print Parameter List / Report

04

Modem Tests

05 06

Not Used RAM Initialize

07 08

Not Used Check & Call

09

System Maintenance

Service Modes (For Facsimile) Description Allows changes to the function parameters (the home position, etc.). (Factory use only) Prints the Function Parameter List, Page Memory Test, Printer Report, All Document File, Protocol Trace, and Toner Order Form. Generates various binary, tonal, and DTMF signals, by the modem. Initialize RAM, and restore the default value of the function parameters. Note: Turn the Power Switch to the OFF, and back to the ON position to enable the parameter settings. Allows input of information for Service Alert Report, Maintenance Alert Report, and Toner Order Form. Used for Firmware Update, Firmware Backup, Parameter Restore, Parameter Backup, Transferring Firmware from the PC to the Flash Card, and Sending a Received File during a fatal printer error. 169

Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

4.2.3.

Fax Service Mode 1 (Function Parameter Setting)

Use the following procedure to change the function parameters. Enter the desired code number, and press “START” key. ↓ If you wish to select another code number, scroll the menu with the “V”, ”/\” arrow keys. ↓ Select the desired function code, and press the "START" key. ↓ When the “CLEAR” key is pressed, the selected code input will not be accepted. ↓ Press “STOP” key twice to exit the service mode.

No. Parameter 000 Monitor/Tel Dial

001 Alarm Status

002 Stop Comm. JRNL 003 Continuous Poll

004 Numeric ID Set

Function Parameter Table Selections Function 1 = Monitor Selects whether the machine starts to TX automatically during On-Hook dialing. 2 = Tel/Dial Monitor : Start to TX after pressing START TEL/DIAL : Start to TX automatically 1 = Off Selects the No Paper, or No Toner alarm status. 2 = Timer OFF : Alarm is disabled. 3 = Constant Timer : Alarm will shut off after 6 seconds. Constant : Alarm will not stop until "STOP" is pressed, or the error is cleared/ corrected. 1 = Off Selects whether the machine prompts to print the 2 = On COMM. Journal when the printout condition is set to INC, and STOP is pressed during communication. 1 = Off Selects whether the Continuous Polling feature is 2 = Stn (Tx only) enabled. 3 = Hub (Rx only) Stn : Place the document(s) on the ADF, or Platen, then press the assigned Program Key to store, or add the documents into a polled file. (See Note 1) Hub : When the polling command is initiated, the machine will continuously poll originals from the remote stations until it is interrupted by pressing "STOP". 1 = Off (will not accept) Selects whether the machine accepts, and allows to 2 = On (accepts) set, or change the Numeric ID.

170 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

No. 005

006 007 008

009 010

011

Function Parameter Table Parameter Selections Function Destination Code 000 : Austria Specified destinations only. 001 : U.K. 002 : Canada 003 : Denmark 004 : Taiwan 005 : Finland 006 : Germany 007 : Netherlands 008 : Italy 009 : Spanish 010 : Hong Kong 011 : Australia 012 : Switzerland 013 : Norway 015 : Portuguese 016 : Ireland 017 : Belgium 018 : Sweden 019 : Turkey 020 : U.S.A. 021 : France 022 : New Zealand 025 : Japan 029 : Poland 030 : Czech 031 : Russia 032 : Greece 033 : Hungary 034 : Indonesia 035 : South Korea 038 : Malaysia 039 : China 045 : Thailand 048 : South Africa 049 : Singapore 050 : Universal 051 : East Euro ID Display 1 = Number (Numeric ID) Selects the priority of displaying the ID. 2 = Chara (Character ID) JRNL Column 1 = Station Selects the contents of the ID to display on the 2 = RCV’D ID Journal. Monitor 1 = Off Selects whether the Monitor is ON/OFF for 2 = On monitoring fax signals. (FOR SERVICE USE ONLY) DC Loop 1 = Off (Normal) Selects a false Off Hook state for back to back 2 = On (Off Hook) communication test. TX Level 00 = 0 dBm Selects the TX signal output level, 0 to -15 dBm in 1 ~ dBm steps. (Refer to Chapter 4.3.of the Service 15 = -15 dBm Manual) RX Level 1 = -43 dBm Selects the receiving sensitivity of -33/-38/-43/-48 2 = -38 dBm dBm. 3 = -33 dBm 4 = -48 dBm 171

Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

No. Parameter 012 DTMF Level

013 G3 RX EQL

014 G3 TX EQL

015 ~ Not Used 016 017 TX Start

018 RX Start

019 ITU-T V.34

020 ITU-T ECM 021 EP Tone

022 Signal Interval

023 TCF Check 024 CED Frequency 025 COMM. Start-Up

Function Parameter Table Selections Function 00 = 0 dBm Selects the DTMF output level, 0 to -15 dBm in 1 ~ dBm steps. 15 = -15 dBm 1 = 0dB Selects the cable equalizer for G3 reception mode, 2 = 4dB 0dB, 4dB, 8dB, or 12dB. 3 = 8dB 4 = 12dB 1 = 0dB Selects the cable equalizer for G3 transmission 2 = 4dB mode, 0dB, 4dB, 8dB, or 12dB. 3 = 8dB 4 = 12dB

2400 bps 4800 bps 7200 bps 9600 bps TC7200 TC9600 12000 bps 14400 bps

Selects the transmission modem start speed, 14400/12000/TC9600/TC7200/9600/7200/4800/ 2400 bps. Press “V”, or “/\ “ to select the symbol rate. Note: This parameter is applicable only when communicating with regular G3 machines. When communicating with Super G3 (V.34) machines, use Parameter No. 32. Selects the reception modem start speed, 14400/ 12000/TC9600/TC7200/9600/7200/4800/2400 bps. Press “V”, or “/\ “ to select the symbol rate. Note: This parameter is applicable only when communicating with regular G3 machines. When communicating with Super G3 (V.34) machines, use Parameter No. 33.

2400 bps 4800 bps 7200 bps 9600 bps TC7200 TC9600 12000 bps 14400 bps 1 = Off 2 = On 3 = Select

1 = Off (Invalid) 2 = On (Valid) 1 = Off (without EP Tone) 2 = On (with EP Tone)

1 = 100 ms 2 = 200 ms 3 = 500 ms 1 = Normal (Short) 2 = Long 1 = 1080 Hz (non ITU-T) 2 = 2100 Hz 1 = First 2 = Second

Selects whether the ITU-T V.34 is Off, On, or Select. Select: Select whether the ITU-T V.34 is Off, or On, when entering Phone Book Dialing Numbers, or Manual Number Dialing. Select the ECM mode. Selects whether to add the echo protect tone on V.29 mode. (Used when Echo Suppression is disabled.) On : Add Off : Do not add Selects the time interval between the receiving signal, and the transmitting signal. Selects the TCF check interval Long/Short Selects the CED frequency 2100/1080 Hz Selects the communication start-up condition (XMT, and Polling). (Used when Echo Suppression is disabled.)

172 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

No. Parameter 026 Non-Standard 027 Short Protocol B 028 Short Protocol D

029 Remote Diagnostics 030 CED & 300 bps

031 RTC = EOL x 12 032 V34 TX Start

033 V34 RX Start

034 V34 TX SR

035 V34 RX SR

036 Not Used 037 Protocol Display

038 Not Used 039 Flash Time

040 Flash Time (PSTN) 041 Pause Time

042 Not Used 043 Redial Interval

044 Redial Count

Function Parameter Table Selections Function 1 = Off (Invalid) Selects own mode (Panafax mode). 2 = On (Valid) 1 = Off (Invalid) Selects the short protocol mode. 2 = On (Valid) 1 = Off (Invalid) Selects the short protocol mode. When activated, it 2 = On (Valid) allows the machine to automatically store the modem speed for each Auto Dial Number. 1 = Off (will not accept) Selects whether the machine accepts Remote 2 = On (accepts) Diagnostics from the service station. 1 = 75 ms Selects the pause interval between the CED, and 2 = 1 sec the 300 bps signal. (Used when Echo Suppression is disabled.) 1 = Off (EOLx6) Selects the RTC signal, EOLx6, or EOLx12. 2 = On (EOLx12) 2400-33600bps Selects the transmission modem start speed for V.34 communication, 33600-2400 bps. Press “V”, or “/\ “ to select the symbol rate. 2400-33600bps Selects the receiving modem start speed for V.34 communication, 33600-2400 bps. Press “V”, or “/\ “ to select the symbol rate. 2400-3429sr Selects the transmission symbol rate for V.34, 3429/ 3200/3000/2800/2400 sr. Press “V”, or “/\ “ to select the symbol rate. 2400-3429sr Selects receiving symbol rate for V.34, 3429/3200/ 3000/2800/2400 sr. Press “V”, or “/\ “ to select the symbol rate. 1 = Off (not displayed) 2 = On (displayed)

Selects whether to display the modem speed during communication. (Press the Job Status Key to display)

5 = 50 ms ~ 100 = 1000 ms 5 = 50 ms ~ 100 = 1000 ms 1 = 1 sec. ~ 10 = 10 sec.

Selects the pause interval before activating the Flash key. Selects the pause interval before activating the Flash key. (For Germany, Austria, and Czech) Selects the pause interval from 1 sec. ~ 10 sec. for dialing through a switchboard, or for international calls.

0 = no waiting ~ 15 = 15 minutes 0 = no redial ~ 15 = 15 times

Selects the redial interval from 0 to 15 minutes in 1 minute steps.

0 ~ 9 (For Australia Only)

Selects the redial count from 0 to 15 times in 1 step intervals. Note: In order to comply with the requirements TBR21 in the EC countries, do not select 15 times.

173 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

No. Parameter 045 Ring Detect Count 046 On-Hook Time

047 Response Wait Interval

Function Parameter Table Selections Function 1 = 1 ring Selects the ring detection count from 1 to 9 rings in ~ 1 ring step intervals. 9 = 9 rings 0 = 0 sec. Selects the on-hook time between sequential ~ communication calls in 1 second step intervals. 90 = 90 sec. 1 = 1 sec. Selects the waiting interval for the response after ~ completing the dialing. 90 = 90 sec. 20 ~ 150 sec. (For France Only)

048~ Not Used 049 050 Ring Detect Mode 1 = Normal 2 = Rough 051 Not Used 052 Pulse Rate

Selects the quality of ringer detection. Use if the line signal is out of regulation, set to "Rough" so that the unit may detect the ringing signals.

1 = 10 pps 2 = 20 pps

Selects the dial pulse rate 10/20 pps.

053~ Not Used 054 055 Busy Tone Check 1 = Off 2 = On 056 Dial Tone Check 1 = Off 2 = On 057 DC Loop Check 1 = Off (Except for USA, 2 = On and Canada) 1 = Off (without image) 058 Comm. JRNL + Image 2 = On (with image) 059 Confidential RCV 1 = Off (does not print out) Report 2 = On (prints out) 060 Version Indicates the Host software version. 061 TX/RX/PRT/CPY TX:****** PRT:****** RX:****** CPY:****** 062 Print Counter 1 = Off 2 = On 063~ Not Used 067 068 NYSE Fax Forward (USA, and Canada Only)

1 = Off 2 = On

Selects whether to detect the Busy Tone. Selects whether to detect Dial Tone before dialing the telephone number. Selects whether the unit checks the DC Loop during communication. Selects whether the machine prints the COMM. Journal with image. Selects whether the machine prints the Confidential RCV Report.

Displays the transmitted, received, total printed, and copied document count. Selects whether to print in the Fax Parameter List, the counter information that is displayed in the Function Parameter No. 61.

Selects whether the machine will forward the incoming, and outgoing faxes to a specified station. Note: Once this parameter is activated, Fax Forwarding via Fax Parameter No. 054 is automatically disabled, an Access Code of "0000" is automatically assigned, and Fax Parameter No. 038 has a new setting added called "NYSE". 174

Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Function Parameter Table No. Parameter Selections Function 069 NYSE Local Print 1 = Inc Selects the printing condition for the incoming faxes (USA, and 2 = On (Always) after FAX Forwarding. Canada Only) INC. : Prints only if FAX Forwarding fails. ON : Always prints. 070 Line Error 128 lines 1. Selects the line disconnect condition during 256 lines reception. If the number of line errors exceed this 512 lines setting, the unit will disconnect the line. 1024 line Press “V”, or “/\ “ to select the symbol rate. 2048 lines 2. Selects the transmit condition of RTP/PIP, or Off (will not disconnect RTN/PIN. line) (Available if No. 73 Error Detect is set to "LINES") (See Note 1) 071 Total Error 1 = 5% Selects the transmit condition of RTP/PIP, or RTN/ 2 = 10% PIN. 3 = 15% (Available if No. 73 Error Detect is set to "RATE".) 4 = 20% (See Note 2) 072 Continuous Error 1 = Off (unlimited) Selects the continuous total error criteria of Off/3/6, 2 = 3 lines/STD or 12 lines in Standard mode. If continuous total 3 = 6 lines/STD error exceeds this setting, the unit will transmit 4 = 12 lines/STD RTN/PIN. (Available if No. 73 Error Detect is set to "RATE".) 073 Error Detect 1 = Lines Selects the error detect condition Lines/Rate. 2 = Rate 074 RTN Receive 1 = Disconnect Selects whether to disconnect the phone line, or 2 = Continue continue when "RTN" is received. 075 Coding 1 = MH (MH only) Selects the coding scheme. 2 = MR (MH, or MR) 3 = MMR (MH, MR, or MMR) 4 = JBIG 076 Batch TX 1 = Off Selects whether the batch transmission is available. 2 = On 077 RX JAM Length 1 = Off (unlimited) Selects the maximum length of a received 2=2m document that can be printed. 078~ Not Used 079 080 Doc Top Feed -99 Adjusts the distance between the scanning sensor ~ ON position, and the scanning start position. +99 081 Doc End Feed -90 Adjusts the distance between the scanning sensor ~ OFF position, and the scanning end position. +127 082 JAM Length 1=1m Selects the maximum length of the original that can 2=2m be scanned. 083 Not Used 084 Line As No Paper 1 = Ring (ring) Selects whether to ring, or send a busy tone to the 2 = Busy (keep line busy) remote station when the recording paper runs out, or the unit cannot receive because of any trouble. 085 Not Used 086 Reduction Fine 1 = Off Selects whether to fix with Fine Mode, or not for the 2 = On Reduction transmission. 175 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

No. 087 088 089 090 ~ 091 092

Parameter Darker Level Normal Level Lighter Level Not Used

093 ~ 094 095 096~ 101 102

Not Used

Smoothing

1 = Off 2 = On

Selects whether the smoothing function is available.

Reduction Ratio Not Used

(70-100)

Selects Print Reduction Ratio (%).

Original Registration

-30 ~ +30 -9 ~ 0

Adjustment of original registration detection timing.

103 Trail Edge Read Timing 104~ 109 110 111 112

Function Parameter Table Selections Function 0 = Lightest Contrast Selects the contrast level. ~ 0← →15 15 = Darkest Contrast Lightest← →Darkest

Adjustment of trail edge void.

Not Used MAC Address Not Used Insert EMAIL TXT 1 = Off 2 = On

113~ Not Used 114 115 Time Zone

116 Overwrite Warning 117~ Not Used 121 122 LDAP 123 One Ring Sound (USA, and Canada Only)

1 = Scroll 2 = Direct

1 = Yes 2 = No

1 = Off 2 = On 1 = Off 2 = On

Indicates the MAC Address. Selects whether the Text Template (email message) is programmable, and added on all email sent in the message body above the top line of text. (Up to 40 characters Programmed in the User Parameters.) Note: After enabling this feature, aside from entering the text in the User Parameters, it also has to be activated in each Auto Dial Number before it will take effect. It does not work for Direct Dialed Numbers.

Selects the setting method for Time Zone. Scroll : Allows using "Scroll Keys" to scroll through the Time Zone Table. Direct : Allows you to input the Time Zone directly, (*) key to be used as a switch between +/-. Selects whether the Overwrite Warning is included on the Internet FAX Result Receipt when programming the Auto Dialer via email.

When LDAP is used, specialized characters may be displayed as different characters. When Function Parameter No. 45 "Ring Detect Count" is set to 1 Ring, and this parameter is enabled (On), the machine will only ring once out loud, answering on the second ring count. 176

Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Function Parameter Table Selections

No. Parameter 124 ~ Not Used 199

Function

Note 1: Continuous Polling (Station Mode) This feature allows you to store, or add documents into a polled file in memory. To enable the Continuous Polling feature set Function Parameter No. 003 to "2:Station". The last Program Key will be assigned with the “Store 4 Poll” Key name automatically and cannot be changed. To prepare the document(s) to be polled, simply place the document(s) on the ADF, or Platen and then press the Program Key to store, or add the document(s) into a polled file. (Note: If a regular polled file is stored in memory, the Program Key for Continuous Polling will not be accepted.) Note 2: Function Parameter No. 070 (Line Error)-Transmit condition of RTP/PIP, or RTN/PIN Signal MCF/PIP RTP/PIP RTN/PIN

1:128 0-31 32-63 64-127

2:256 0-63 64-127 128-255

Setting 3:512 4:1024 0-127 0-255 128-255 256-511 256-511 512-1023

5:2048 0-511 512-1023 1024-2047

6:Off Always -

Note 3: Function Parameter No. 071 (Total Error)-Transmit condition of RTP/PIP, or RTN/PIN Signal MCF/PIP RTP/PIP RTN/PIN

1:5% 0-2 3-4 5-

Setting 2:10% 3:15% 0-4 0-7 5-9 8-14 1015-

4:20% 0-9 10-19 20-

Note 4: The default setting of parameters depends on the country’s specifications, or regulations. Print the Function Parameter List to confirm the default settings.

177 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

4.2.4.

Fax Service Mode 3 (Printout of Lists, Reports, and Test Results)

From this Service Mode you can print the Function Parameter List, Page Memory Test, Printer Report, All Document File, Protocol Trace, and the Toner Order Form.

4.2.4.1.

Function Parameter List

A list of all Function Parameters can be printed by the following procedure. Press the “V”, ”/\” arrow keys to select the "3: Print Report/List" on the display. ↓ Press the “SET” key to select the "1: Function Parameter List". ↓ Press the “SET” key. ↓ Press the “STOP” key twice to exit the service mode.

178 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Function Parameter List (Sample) ************* -FUNCTION PARAMETER- ************* DATE MMM-dd-yyyy ***** TIME 12:07 ***P.01 000 001 002 003 004 005 006 007 008 009

Mon/Tel Dial Alarm Status Stop Comm. JRNL Continuous Poll Numeric ID Set Destination Code ID Display JRNL Column Monitor DC Loop

Monitor Timer On Off On 999 Chara Station Off Off

050 051 052 053 054 055 056 057 058 059

Ring Det Mode ---------Pulse Rate ------------------Busy Tone Check Dial Tone Check DC Loop Check Comm. JRNL + Image Conf. RCV Report

010 011 012 013 014 015 016 017 018 019

TX Level RX Level DTMF Level G3 RX EQL G3 TX EQL ----------------TX Start RX Start ITU-T V.34

-9dBm -43dBm -5dBm 0dB 0dB

14400bps 14400bps On

060 061 062 063 064 065 066 067 068 069

Version ..... AcV........ TX/RX/PRT/CPY 000080/000168/000003/000000 Print Counter Off ----------------------------------------------------------------

020 021 022 023 024 025 026 027 028 029

ITU-T ECM EP Tone Sig. Interval TCF Check CED Freq. Comm. Start-Up Non-Standard Short Protocol B Short Protocol D Remote Diag.

On Off 500ms Normal 2100Hz First On On On On

070 071 072 073 074 075 076 077 078 079

Line Error Total Error Conti. Error Error Detect RTN Receive Coding BATCH TX:[On] RX JAM Length -------------------

128 10 Off Rate Discon JBIG On 2 m

030 031 032 033 034 035 036 037 038 039

CED & 300bps RTC = EQL x 12 V34 TX Start V34 RX Start V34 TX SR V34 RX SR --------Protocol Display --------Flash Time

75ms Off 33600bps 33600bps 3429sr 3429sr

080 081 082 083 084 085 086 087 088 089

Doc Top Feed Doc End Feed JAM Length ---------Line As NoPaper ---------Reduction Fine Darker Level Normal Level Lighter Level

0 0 2 m

040 041 042 043 044 045 046 047 048 049

--------Pause Time --------Redial Interval Redial Count Ring Det. Count On-Hook Time Response Wait -----------------

090 091 092 093 094 095 096 097 098 099

------------------Smoothing ------------------Reducton Ratio -------------------------------------

Off 500ms

3sec 3min 5 2 5sec 55sec

-PANASONIC *****

******************* -PANASONIC

Normal 10pps

On Off Off On On

Ring On 2 8 4

On

100%

-

- ****** -12345678901234567890- *********

Note: 1. The contents of the Function Parameter List may vary depending on the country’s regulations. 2. “ * ” mark will be shown on the left side of number when setting was changed from default.

179 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

4.2.4.2.

Page Memory Test

A test pattern prints out for checking the page memory, and printer mechanism using the following procedure. Press the “V”, ”/\” arrow keys to select the "3: Print Report/List" on the display. ↓ Press the “SET” key to select the "1: Function Parameter List". ↓ Press the “V”, ”/\” arrow keys to select the "3: Page Memory Test". ↓ Press the “SET” key. ↓ Press the “STOP” key twice to exit the service mode.

************* TEST PATTERN PRINT **************** DATE MMM-dd-yyyy ***** TIME 12:07 ***P.01

SC SC BOOT PNL SPC FAX MODEM SC2

: : : : : :

TX/RX/PRT/CPY MEMORY SIZE MAC ADDRESS SHIPMENT SET

: 000123/000456/000789/000666 : (2 MB) : 08002300E078

-PANASONIC *****

****************** -PANASONIC

-

- ****** -12345678901234567890- ***********

180 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

4.2.4.3.

Printer Report

All printer errors are logged on the Printer Report which can be printed by the following procedure. Press the “V”, ”/\” arrow keys to select the "3: Print Report/List" on the display. ↓ Press the “SET” key to select the "1: Function Parameter List". ↓ Press the “V”, ”/\” arrow keys to select the "4: Printer Report". ↓ Press the “SET” key. ↓ Press the “STOP” key twice to exit the service mode.

**************-PRINTER REPORT-********************* DATE MMM-dd-yyyy ***** TIME 19:02******** LAST PRINT ERROR

: MMM-dd-yyyy 15:38 J00

SERIAL NUMBER CUSTOMER ID

: : 1234567890123456

FIRMWARE VERSION SC PNL SPC

: : :

TRANSMIT COUNTER RECEIVE COUNTER COPY COUNTER PRINT COUNTER

: : : :

00-00000016

000475 000398 000083 000016

ERROR CODE RRROR COUNT NO.DATE & TIME ERROR CODE RRROR COUNT | NO.DATE & TIME -------------------------------------------------------------------------------------------01.MMM-dd-yyyy 15:38 J00 00-00000016 | 02.MMM-dd-yyyy 10:48 J02 00-00000016 | --------------------------------------------------------------------------------------------

-PANASONIC *****

*******************-PANASONIC

-

-*******-12345678901234567890-**************

181 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

4.2.4.4.

All Document Files

Print the document files from the Flash Memory. Press the “V”, ”/\” arrow keys to select the "3: Print Report/List" on the display. ↓ Press the “SET” key to select the "1: Function Parameter List". ↓ Press the “V”, ”/\” arrow keys to select the "5: All Document Files". ↓ Press the “SET” key. ↓ Press the “STOP” key twice to exit the service mode.

182 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

4.2.4.5.

Protocol Trace

Print a Protocol Trace Report for the previous communication. Press the “V”, ”/\” arrow keys to select the "3: Print Report/List" on the display. ↓ Press the “SET” key to select the "1: Function Parameter List". ↓ Press the “V”, ”/\” arrow keys select the "6: Protocol Trace". ↓ Press the “SET” key. ↓ Press the “STOP” key twice to exit the service mode.

*************** PROTOCOL LOG. REPORT ****************** DATE MMM-dd-yyyy ***** TIME 16:56 *******

STATUS MODE SPEED REMOTE CAPA. LOCAL CAPA.

: : : : :

OK ECM-TX (STANDARD) 9600bps 0MS/L DIS 00 CE B9 C4 80 12 TSI 2B 20 20 20 38 37 2B 2B 2B 2B 39 38 36 36 35 34 37 38 38 30 DCS 00 C6 F8 44

COMMAND LOG. REMOTE : NSF CSI DIS CFR LOCAL : TSI DCS PIX PPS-EOP -----------------------------------------------------------------REMOTE : MCF LOCAL : DCN -PANASONIC ****************************-PANASONIC

-*************-12345678901234567890-***************

183 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

4.2.4.6.

Toner Order Form

The Toner Order Form can be printed out manually by the following procedure. Press the “V”, ”/\” arrow keys to select the "3: Print Report/List" on the display. ↓ Press the “SET” key to select the "1: Function Parameter List". ↓ Press the “V”, ”/\” arrow keys to select the "7: Toner Order Form". ↓ Press the “SET” key. ↓ Press the “STOP” key twice to exit the service mode.

184 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

************************************* > TONER BOTTLE ORDER FORM < *************************************

**** The toner supply in your machine is running low **** (1) To order a replacement Bottle from your Authorized Dealer

by Phone: by Fax:

1 201 111 5555 (2) 1 201 111 4444 (3)

Thank you for your order.

Customer Name and Address ========================= Ship to:

Bill to:

Attention:

Attention:

Phone No.:

Phone No.:

Customer ID: ABC COMPANY (4)

P.O. No.(if required):

Toner Cartridge:

(5)

Serial No.:

Quantity Required:

/ Print your name and title

/

Signature & Date

Explanation of Contents (1) Low Toner Message (Fixed)

“The toner supply in your machine is running low”

(2) Toner Order Tel #

Up to 36 digits

(3) Toner Order Fax #

Up to 36 digits

(4) Customer ID

Up to 16 characters (User Identification Code)

(5) Toner Cartridge

DQ-TU10J (For DP-8020E/8020P/8016P Except for USA, Canada, and China) DQ-TUJ10K (For DP-8020E/8020P/8016P for USA, Canada, and China)

185 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

4.2.5. 4.2.5.1.

Fax Service Mode 4 (Modem Test) Binary Signal

This Service Mode is used to check the binary signal output. Signals can be output to the line using the following procedure. Press the “V”, ”/\” arrow keys to select the "4: MODEM Test" on the display. ↓ Press the “SET” key to select the "1: Signal Test". ↓ Press the “SET” key. ↓ Press the desired number. ↓ Press the “SET” key. ↓ Press the “STOP” key twice to exit the service mode. Binary Signal Table Number 1 2 3 4 5 6 7 8 9

Signals V21 300bps V27ter 2400bps V27ter 4800bps V29 7200bps V29 9600bps V17 TC7200bps V17 TC9600bps V17 12000bps V17 14400bps

186 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

4.2.5.2.

Tonal Signal

This Service Mode is used to check the tonal signal output. Signals can be output to the line using the following procedure. Press the “V”, ”/\” arrow keys to select the "4: MODEM Test" on the display. ↓ Press the “SET” key to select the "2: Tonal Test". ↓ Press the “SET” key. ↓ Press the desired number, and press the "START" key. ↓ Press the “STOP” key twice to exit the service mode. Tonal Signal Table Number 1 2 3 4 5 6 7

Signals 462 Hz 1080 Hz 1100 Hz 1300 Hz 1650 Hz 1850 Hz 2100 Hz

187 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

4.2.5.3.

DTMF Signal

This Service Mode is used to check the DTMF (Dual Tone Multi Frequency) signal output. The DTMF signal can be generated using the following procedure. • DTMF Single Tone Press the “V”, ”/\” arrow keys to select the "4: MODEM Test" on the display. ↓ Press the “SET” key to select the "3: DTMF Test". ↓ Press the “SET” key. ↓ Press the “V”, ”/\” arrow keys to select the "1. Single". ↓ Press the desired number, and press the "START" key. ↓ Press the “STOP” key twice to exit the service mode. • DTMF Dual Tone Press the “V”, ”/\” arrow keys to select the "4: MODEM Test" on the display. ↓ Press the “SET” key to select the "3: DTMF Test". ↓ Press the “SET” key. ↓ Press the “V”, ”/\” arrow keys to select the "2. Dual". ↓ Press the desired number, and press the "START" key. ↓ Press the “STOP” key twice to exit the service mode. DTMF Single Tone Table Number 1 2 3 4 5 6 7 8

DTMF Dual Tone Table

DTMF Signal Tones 697 Hz 770 Hz 852 Hz 941 Hz 1209 Hz 1336 Hz 1477 Hz 1633 Hz

Number 0 1 2 3 4 5 6 7 8 9 * #

DTMF Dual Tones 941 Hz + 1336 Hz 697 Hz + 1209 Hz 697 Hz + 1336 Hz 697 Hz + 1477 Hz 770 Hz + 1209 Hz 770 Hz + 1336 Hz 770 Hz + 1477 Hz 852 Hz + 1209 Hz 852 Hz + 1336 Hz 852 Hz + 1477 Hz 941 Hz + 1209 Hz 941 Hz + 1477 Hz

188 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

4.2.5.4.

Binary Signal (V.34)

This Service Mode is used to check the binary signal output. Signals can be output to the line using the following procedure. (V.34) Press the “V”, ”/\” arrow keys to select the "4: MODEM Test" on the display. ↓ Press the “SET” key to select the "4: V34 MODEM". ↓ Press the “SET” key. ↓ Press the desired number, and press the "START" key. ↓ Press the “STOP” key twice to exit the service mode. Binary Signal Table Number 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21

Signals V34 2400 sr 2400 bps V34 2400 sr 4800 bps V34 2400 sr 7200 bps V34 2400 sr 9600 bps V34 2400 sr 12000 bps V34 2400 sr 14400 bps V34 2400 sr 16800 bps V34 2400 sr 19200 bps V34 2400 sr 21600 bps V34 2800 sr 4800 bps V34 2800 sr 7200 bps V34 2800 sr 9600 bps V34 2800 sr 12000 bps V34 2800 sr 14400 bps V34 2800 sr 16800 bps V34 2800 sr 19200 bps V34 2800 sr 21600 bps V34 2800 sr 24000 bps V34 2800 sr 26400 bps V34 3000 sr 4800 bps V34 3000 sr 7200 bps

Number 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42

Signals V34 3000 sr 9600 bps V34 3000 sr 12000 bps V34 3000 sr 14400 bps V34 3000 sr 16800 bps V34 3000 sr 19200 bps V34 3000 sr 21600 bps V34 3000 sr 24000 bps V34 3000 sr 26400 bps V34 3000 sr 28800 bps V34 3200 sr 4800 bps V34 3200 sr 7200 bps V34 3200 sr 9600 bps V34 3200 sr 12000 bps V34 3200 sr 14400 bps V34 3200 sr 16800 bps V34 3200 sr 19200 bps V34 3200 sr 21600 bps V34 3200 sr 24000 bps V34 3200 sr 26400 bps V34 3200 sr 28800 bps V34 3200 sr 31200 bps

Number 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61

Signals V34 3429 sr 4800 bps V34 3429 sr 7200 bps V34 3429 sr 9600 bps V34 3429 sr 12000 bps V34 3000 sr 19200 bps V34 3429 sr 16800 bps V34 3429 sr 19200 bps V34 3429 sr 21600 bps V34 3429 sr 24000 bps V34 3429 sr 26400 bps V34 3429 sr 28800 bps V34 3429 sr 31200 bps V34 3429 sr 33600 bps ANSam CM JM INFO0c & TONEB INFO0c & TONEA PPh & AC & ALT

189 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

4.2.6.

Fax Service Mode 6 (RAM Initialization)

Initializes RAM, and restores the Function Parameters to their default values. Note: This operation should be performed when the unit is first installed. Press the “V”, ”/\” arrow keys to select the "6: RAM initialize" on the display. ↓ Press the “SET” key to select the desired Mode number. ↓ Press the "SET" key to initialize RAM. ↓ Press the “STOP” key twice to exit the service mode. RAM Initialization Table No. 01

Initialize Mode PARAMETER INITIALIZE

02 03

JOURNAL CLEAR AUTO DIAL CLEAR

04 05 06 07

PROGRAM DIAL CLEAR LOGO/ID/PSWD CLEAR LBP ERROR LOG CLEAR SHIPMENT SET

08 09

FLASH MEMORY CLEAR ALL JOB CLEAR

Description Restores the Fax, and Function Parameters to default values. Note: Turn the Power Switch to the OFF, and back to the ON position to enable the parameter settings. Clears the Journal contents. Clears the One-touch, ABBR Numbers, and Phone Books. Clears the Program keys. Clears the Logo, ID, Polling Password. Clears the Printer Error Log. Deletes all setting information, except parameter number 80, and 81, then set default values. Deletes all information in the Flash Memory. Clears all Jobs stored in Flash Memory.

190 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

4.2.7. 4.2.7.1.

FAX Service Mode 8 (Check & Call) Overview

This feature enables the Authorized Servicing Dealers to manage, and improve the machine maintenance to their customers by alerting them of equipment problems. It also can be used as a Supply Sales Tool by alerting the Dealer that the unit is running Low on Toner. The function overview is as follows: 1. The machine’s printer error information is stored in the Printer Report. 2. The printer report can be manually printed when required. 3. When printer errors occurs, the unit can automatically transmit the Service Alert Report to the preregistered telephone number, or email address. 4. When the unit detects Low Toner, or PM counter reached the maintenance timing, it can automatically transmit the Maintenance Alert Report to the pre-registered telephone number, or email address. Press the “V”, ”/\” arrow keys to select the "8: Check & Call" on the display. ↓ Press the “SET” key to select the desired code number. (i.e. 01 Service Alert Fax #, input the telephone No., or for an email address, press the "FAX/EMAIL" Mode key, and input the email address.) ↓ Press the "SET" key. ↓ Press the “STOP” key twice to exit the service mode.

4.2.7.2.

Printer Reports

• Conditions under which a report can be printed, or transmitted 1. Manual print The Printer Report can be printed by Service Mode 3. (See Sect. 4.2.4.3. of the Service Manual) 2. Automatic transmission/printout a. Service Alert Report When the unit detects an Emergency Printer Error, the unit will immediately transmit the Service Alert Report to the pre-registered telephone number, or email address. However, the unit will not transmit the Service Alert Report if it finds the same error within the same date in the error log. b. Maintenance Alert Report When the unit detects Low Toner, the unit can automatically transmit the Maintenance Alert Report to the pre-registered telephone number, or email address. Refer to the Error Code Table. c. Toner Order Form When the unit detects Low Toner, the unit can automatically print the Toner Order Form with the preregistered order information. d. Call Counter Report When the printer counter reaches the pre-set number, the unit can automatically transmit the Call Counter Report to the pre-registered telephone number, or email address. Note: The Service, and Maintenance Alert Reports are managed in the same manner as the normal memory transmission (Retry, Incomplete, File List, Display while it is transmitting, Journal).

191 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Error Code Ex-xx E13 Jxx Uxx U13

Log O

Tx Remarks Report S Refer to the Mechanical Error Code (E Code) Table. (Sect. 3.6.3.) Out of Toner. Refer to the Jam Error Code (J Code) Table. (Sect. 3.6.2.) Refer to the User Error Code (U Code) Table. (Sect. 3.6.1.) M Low Toner.

Note: TX (Transmission) Report: S = Service Alert Report, M = Maintenance Alert Report

192 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

4.2.7.3.

SERVICE ALERT REPORT FORMAT

*************************************************** DATE MMM-dd-yyyy ***** TIME 03:47 ******** **************************** > SERVISE ALERT REPORT < **************************** LAST PRINT ERROR SERIAL NUMBER (1) CUSTOMER ID (2) FIRMWARE VERSION SC PNL SPC

: MMM-dd-yyyy 20:07 E04-01

00-00000013

: : ABC COMPANY : : :

(3) COUNTER INFORMATION: F7-02 F7-03 F7-04 F7-05 F7-06 F7-07 F7-08 F7-10 F7-11 F7-12 F7-13 F7-14 F7-15 F7-16 F7-17 F7-18 F7-19 F7-20 F7-21 F7-21

Total Count PM COUNT Scanner PM Count . . . . . OPC Drum Count Process Unit Count ADF PM Count Developer Count Sheet Bypass Count 1st Paper Tray Count 2st Paper Tray Count 3st Paper Tray Count 4st Paper Tray Count 2-Sided Count ADF/iADF Count ADF/iADF Read Count Scanner Count Scanner Read Count Copy Print Count Copy Scan Count

Call Counter Pri-set Value

CURRENT 13 13 9

PM CYCLE (------) 120000 (------)

: : : : : : : : : : : : : : : : :

13 13 1 13 0 3 0 0 0 0 0 0 0 0 0 0

(------) (------)

:

999999

: :

F7-23 F7-24 F7-25 F7-26 F7-27 F7-28 F7-29 F7-30 F7-31 F7-32

PC Print Count PC Scan Count FAX Transmit Count FAX Receive Count FAX Print Count OPC Drum Rotate A4/LT Count A4R/LTR Count A3/LD Count B4/LG Count

: : : : : : : : : :

0 6 0 0 0 0 0 0 0 0

(4) PRINT ERROR: NO. DATE & TIME ERROR CODE ERROR COUNT | NO. DATE & TIME ERROR CODE ERROR COUNT ------------------------------------------------------------------------------------------01 MMM-dd-yyyy 20:07 E04-01 00-00000013 | 02 MMM-dd-yyyy 20:04 E04-01 00-00000013 | | | | | -------------------------------------------------------------------------------------------

-LOGO PANASONIC *****

*********************** -CHARACTER ID

-

- ***** -31415926535897932384-*********

Explanation of Contents (1) Customer ID (2) Firmware Version (3) Counter Information (4) Print Error

Last 30 records (Latest on top)

193 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

4.2.7.4.

MAINTENANCE ALERT REPORT FORMAT

*************************************************** DATE MMM-dd-yyyy ***** TIME 12:00 ******** **************************** > MAINTENANCE ALERT REPORT < ****************************

LAST PRINT ERROR : MACHINE IS RUNNING OUT OF TONER (1) SERIAL NUMBER CUSTOMER ID

: : ABC COMPANY (2)

(3) FIRMWARE VERSION SC : PNL : SPC : TRANSMIT COUNTER RECEIVE COUNTER COPY COUNTER PRINT COUNTER

: : : :

000244 000082 000000 000000

(4)

NO.DATE & TIME ERROR CODE ERROR COUNT NO.DATE & TIME ERROR CODE ERROR COUNT -----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

-LOGO PANASONIC ************************************ -CHARACTER ID

-

- ***** -31415926535897932384-***********

Explanation of Contents (1) Low Toner Message (Fixed)

“MACHINE IS RUNNING OUT OF TONER”

(2) Customer ID

Up to 16 characters (User Identification Code)

(3) Firmware Version (4) Transmission / Reception / Copy / Print Counters

194 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

4.2.7.5.

Toner Order Form ************************************* > TONER BOTTLE ORDER FORM < *************************************

**** The toner supply in your machine is running low **** (1) To order a replacement Bottle from your Authorized Dealer

by Phone: by Fax:

1 201 111 5555 (2) 1 201 111 4444 (3)

Thank you for your order.

Customer Name and Address ========================= Ship to:

Bill to:

Attention:

Attention:

Phone No.:

Phone No.:

Customer ID: ABC COMPANY (4)

P.O. No.(if required):

Toner Cartridge:

(5)

Serial No.:

Quantity Required:

/ Print your name and title

/

Signature & Date

Explanation of Contents (1) Low Toner Message (Fixed)

“The toner supply in your machine is running low”

(2) Toner Order Tel #

Up to 36 digits

(3) Toner Order Fax #

Up to 36 digits

(4) Customer ID

Up to 16 characters (User Identification Code)

(5) Toner Cartridge

DQ-TU10J (For DP-8020E/8020P/8016P Except for USA, Canada, and China) DQ-TUJ10K (For DP-8020E/8020P/8016P for USA, Canada, and China)

195 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

4.2.7.6.

CALL COUNTER REPORT

*************************************************** DATE MMM-dd-yyyy ***** TIME 03:47 ******** ***************************************************************** > SCHEDULED REPORT - CALL COUNTER HAS REACHED PRE-SET VALUE < ***************************************************************** LAST PRINT ERROR : MMM-dd-yyyy 20:07 E04-01 00-00000013 SERIAL NUMBER (1) CUSTOMER ID (2) FIRMWARE VERSION SC PNL SPC

: : ABC COMPANY : : :

(3) COUNTER INFORMATION: F7-02 F7-03 F7-04 F7-05 F7-06 F7-07 F7-08 F7-10 F7-11 F7-12 F7-13 F7-14 F7-15 F7-16 F7-17 F7-18 F7-19 F7-20 F7-21 F7-21

Total Count PM COUNT Scanner PM Count . . . . . OPC Drum Count Process Unit Count ADF PM Count Developer Count Sheet Bypass Count 1st Paper Tray Count 2nd Paper Tray Count 3rd Paper Tray Count 4th Paper Tray Count 2-Sided Count ADF/iADF Count ADF/iADF Read Count Scanner Count Scanner Read Count Copy Print Count Copy Scan Count

Call Counter Pri-set Value

: : : : : : : : : : : : : : : : : : : : :

CURRENT 13 13 9

PM CYCLE (------) 120000 (------)

13 13 1 13 0 3 0 0 0 0 0 0 0 0 0 0

(------) (------)

F7-23 F7-24 F7-25 F7-26 F7-27 F7-28 F7-29 F7-30 F7-31 F7-32

PC Print Count PC Scan Count FAX Transmit Count FAX Receive Count FAX Print Count OPC Drum Rotate A4/LT Count A4R/LTR Count A3/LD Count B4/LG Count

: : : : : : : : : :

0 6 0 0 0 0 0 0 0 0

1

(4) PRINT ERROR: NO. DATE & TIME ERROR CODE ERROR COUNT | NO. DATE & TIME ERROR CODE ERROR COUNT ------------------------------------------------------------------------------------------01 MMM-dd-yyyy 20:07 E04-01 00-00000013 | 02 MMM-dd-yyyy 20:04 E04-01 00-00000013 | | | | | | | | -------------------------------------------------------------------------------------------

-LOGO PANASONIC *****

*********************** -CHARACTER ID

-

- ***** -31415926535897932384-*********

Explanation of Contents (1) Customer ID (2) Firmware Version (3) Counter Information (4) Call Counter Pre-Set Value

196 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

4.2.8.

Service Mode 9 (System Maintenance)

4.2.8.1.

Overview

This Service Mode is used to maintain the machine. Use the following procedure for System Maintenance. Press the “V”, ”/\” arrow keys to select the "9: System Maintenance" on the display. ↓ Press the “SET” key to select the "1: Send RCV’D File". The display changes to the Fax Mode. ↓ Select the desired Fax number. ↓ Press "START" to send the Fax. After the transmission, the machine returns to the Stand-by Mode. Note: If there is NO File in the machine, this operation will not function. Press the “STOP” key twice to exit the service mode. System Maintenance Table No. Maintenance Mode 01 Send RCV'D File

Description Transfers documents from memory to another fax machine during a fatal printer error.

197 Ver. 1.0

OCT 2006

5 Exploded View & Parts List

DP-8020E/8020P/8016P

Note: 1. Panasonic Digital Document Company and other Panasonic Sales Companies reserve the right to change any information enclosed herein without prior notification. (This includes, but is not limited to, parts pricing, availability, and text) 2. Electrical parts supplied may include previously used components. 3.

Important Safety Notice

Components identified by a mark, have special characteristics important for safety. When replacing any of these components, use only manufacturer’s specified parts. 4. In New Parts column, "N" indicates part is used only in DP-8020E/8020P/8016P models, "C" indicates part is used in previous models. 5. In Remarks column, "PM" indicates “Preventive Maintenance Part". 6. In Remarks column, "RTL" indicates that the Retention Time is limited for this item. After the discontinuation of this assembly in production, the item will continue to be available for a specific period of time. The retention period of availability is dependant on the type of assembly, and in accordance with the laws governing part and product retention. After the end of this period, the assembly will no longer be available. 7. This “Unit" which includes other itemized parts is provided as “Limited Availability" for your convenience, and will only be offered for up to 3 years after the production of the unit ceases. However, the individual contents of the assembly will be available for the standard period. 8. For Screw identification and Part Number, please refer to the last section of this chapter. 9. Important Notice (Especially in those countries belonging to the European Union): This product is fully compliant with the national laws transposed from the EU Directive on the restriction of the use of certain hazardous substances (RoHS) in electrical and electronic equipment, effective 1st July 2006 in the EU countries. In order for the product to comply with the RoHS Directive, the six particular substances (lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls, and polybrominated diphenyl ethers) have been either totally eliminated or limited to the concentration level below maximum allowed. Consequently spare parts have been changed to RoHS-compliant parts where applicable. To ensure compliance with the spare parts application of the RoHS legislation, please make sure to follow the details provided in this manual when ordering spare parts and carrying out repairs.

198 Ver. 1.0

OCT 2006

5.1.

DP-8020E/8020P/8016P

Destination Codes

Code PA PB

5.1.1.

Destination Australia; New Zealand England; Singapore; Malaysia; Hong Kong

PF

France

PK PM

China Germany; Austria; Italy; Spain

Code PP PS PT PU PUG PY

Destination Czech; Slovakia; Poland; Hungary Turkey Taiwan USA; Canada; Puerto Rico; Mexico; Panama GSA Saudi Arabia

Destination Codes for Fax Option

Code AAR ABR AER AGR AHR AJR AKR ALR AMR APR ARR ATR AUR AVR AWR

Destination

Code EER ENR YAR YCR YGR YMR YPR YRR YSR YTR YVR YWR YXR

Austria England Taiwan Germany Netherlands Spain Hong Kong SAR, PRC Australia Switzerland Portugal Belgium Turkey USA; Canada; Puerto Rico France New Zealand

YYR

Destination Italy Norway; Sweden Panama; (220 VAC Power Supply) Slovakia Greece Malaysia Czech; Poland; Hungary Russia; Ukraine Saudi Arabia Thailand China South Africa Singapore Mexico; Panama; (120 VAC Power Supply)

Note: 1. DP-8020P is not available for USA and Canada. 2. Model availability may differ as per destination. Please ask your sales company for details.

199 Ver. 1.0

OCT 2006

5.2. Safety Mark

DP-8020E/8020P/8016P

Cover Assembly Ref. No. 101

DZMA004441

Cover, Left Scanner

New Parts C

102

DZMA004443

Cover, Rear Scanner

C

All

103 104 105 106

DZMA002394 PJHEC0124Z DZMH000013 DZTE000025 DZJE001189 DZJE001191 DZJE001188

Cover, Platen Pad, Scanning Hinge, Platen Glass, Platen (L)

C C C C

Plate, Rear Document

C

All All All All PU, PUG PK, PT

C

Other PU, PUG PK, PT

107

109 110 112 113 114 116 117 120 121 122 123 124 125 126 127 128 129 131 132 133 135 136 2832 2841

Part Number

DZHP010632 DZHP010631 DZHP010630 DZTE000052 DZJA001385 DZJA001386 DZJM001318 DZJM001403 DZKN000266 DZML000489 DZKR000038 DZML000491 DZKL000087 DZML000490 DZLF000208 DZML000488 DZNK005316 DZNK005266 PJGFC0033Z DZJF000658 DZJF000657 DZAL000211 DZMA004445 DZJF000662 DZNE000129 PJRCC0005Z DZEC102304R

DZFP001590 DZEC102917R 2910 DZEC103157R Q8 XTB3+8GFN S6 DZPA000086 W9 XTB3+12JFJ X2 DZPA000089 X8 XTB3+8GFJ Y3 XTW3+6LFJ

Part Name

Assembly, Document Plate Glass, Scanning (S) Bracket, Left Hinge Bracket, Right Hinge Guide, OPS Actuator, OPS Spring, Actuator Cover, Bypass Tray Spring, Tray Hold Up Tray, Sub Bypass 2 Actuator, Paper Tray Tray, Sub Bypass Gear, Guide Tray, Bypass

C C C C C C C C C C C C C

Label, Bypass Tray

C

Guide, Rear Set Guide, Front Set Sensor, Photo Cover, Right Scanner Lever, Guide Sheet, Harness Label 3, Sensor PC Board, SNS Harness, MPS

C C C C C C C C

PC Board, SSN

C

Screw Screw Screw Screw Screw Screw

C C C C C C

C

Remarks

Destination All

Other All All All All All All All All All All All All All PU, PUG Other PK, PT All All All All All All All All All Except PK, PT PK, PT All All All All All All

200 Ver. 1.0

OCT 2006

A

B

C

DP-8020E/8020P/8016P E

D

107

X2

103

106 1

110 116 109 Y3

117 105

X2 132

2832

104 W9

X2

Y3 2

S6 114

X8

113

Y3 112

3

102 See Fig. 3 S6 101

4

Y3 See Fig. 7

5

129

Q8

136

135

133

128

126 125

6

Y3

127 124

2841

2910 X8

2841 Q8 131

123

7

122 120 121

8

Fig. 1 Cover Assembly (1/2)

X8

201 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P Safety Mark

Ref. No.

Part Number

Part Name

New Parts

Remarks

Destination

For DP-8020E/8020P*

201

DZMA004817 DZMA004818

Cover, Front Door

N

202

DZMA004453

Cover, Exit

C

All

203

DZMA004440

C

All

204

DZNK005270

C

All

205 206 207 208

C C C C

All All All All PK, PT

Label, Laser Caution

C

210

DZJB000447 DZKQ000119 DZJA000187 DZGD000001 DZNK005449 DZNK005268 DZNK005269

Cover, Connector Label, Toner Bottle Exchange Angle, Door Cover Spring, DC Bracket, Magnet Magnet

Label, Toner Bottle

C

PU,PUG,Other All

211

DZMA004447

Cover 1, Front

C

All

212 213 214

PJGFC1214Z DZJB000186 DZMG000038

Label, EPA Plate, Magnet Latch, Waste Toner Box

C C C

All All All

215

DZMA004450

Cover, Left Front

C

All

216 217 218 219 220 223

DZMA004449 DZMA004500 DZMA004451 DZMA004452 DZMA004454 FFPTE2719 DZNK005283 PJGTC0053Z

Cover, Cover, Cover, Cover, Cover, Label,

C C C C C C

Label, Heater Main

C

225

DZNK005284

Label, Switch

C

All

226

DZJJ000017

Wire, Front Door

C

All

227

K0AHLE000003

Switch, Interlock

C

All

228 229 232 233 234

DZJB000425 DZKK000120 DZPA000097 DZUJ000023 DZNK004580

Bracket, Interlock SW Lever, Interlock Screw Packing, Inner Cover Label, Energy

C C C C C

All All All All PB

235

DZNK002411

Label, Ground Warning

C

PB, PS

236

DZNK003248

Label, Class A

C

PK

237 238 239 938

PJUIC0218Z PJUIC0219Z PJUIC0221Z DZPA000092

Base, Key Counter Cover, Key Counter Cover, Key Counter Front Screw

C C C C

952

PJHSC0025Z

Gasket

C

Q8 S6 X8 Y1 Y2 Y3 Y11

XTB3+8GFN DZPA000086 XTB3+8GFJ XTW3+8PFJ XTB3+6FFJ-RP XTW3+6LFJ XSB4+10FJ

Screw Screw Screw Screw Screw Screw Screw

C C C C C C C

All All All All PA, PB, PF, PM, PP, PS, PY All All All All All All All

209

224

Right F Card Rear Side Inner Rear F-ROM

For DP-8016P

All

All All All All All For DP-8020E/8020P* All PU,PUG,Other PK

202 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P A

B

C

D

238 Y3

E

Y11

Y2

234

1

235, 236 237

Y2 239 217

Q8

223

216 220

2

S6

224

225 952 3

233

4

S6 226

218

232

Y3

938 219

211

212 5

227 215

214

Y3 X8

229

228

213 209

Y1

204 208 207

206

210

6

203

Y3 X8 205 201

7

202

8

Fig. 2 Cover Assembly (2/2)

203 Ver. 1.0

OCT 2006

5.3. Safety Mark

DP-8020E/8020P/8016P

Scanner Unit Ref. No. 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315

DZJB000431 DZLD000024 DZJL000395 DZHP009898 DZJL000396 DZKN000404 DZJF000648 DZLC000001 DZJA001388 DZJA001387 DZJK000106 DZLB000022 DZJA001392 DZKN000403 DZJN000087

Frame, Upper Scanner Drum, Wire Wire, Rear Assembly, Drive Shaft Wire, Front Spring, Wire Guide, Wire Pulley, Idler Rail, Rear Rail, Front Holder, Lamp Harness Pulley, Scanner Bracket, Motor Spring, Motor Plate, Rubber

316

DZGG000074

Motor, Scanning

C

All

317 318 319 131 2817 H7 J7 J8 Y3

DZLM000214 DZLK000044 DZJM001366 DZAL000211

Bushing Belt, Synchro Sheet, Protection Sensor, Photo Harness, SNS Snap Ring E-Ring E-Ring Screw

C C C C

All All All All All All All All All

Part Number

DZFP001598 FFPFJ0041B XUC4VM XUC7VM XTW3+6LFJ

Part Name

New Parts C C C C C C C C C C C C C C C

C C C C C

Remarks

Destination All All All All All All All All All All All All All All All

204 Ver. 1.0

OCT 2006

A

B

C

DP-8020E/8020P/8016P E

D

315 301

315

1

319 Y3 318

J8

2817

317

2

131

302 Y3 304

302

H7

3

J7

309

308

317 See Fig. 4

303 H7

4

H7

See Fig. 4

308

308

306

305 310

5

308 316 H7 313

Y3 312

311

Y3

6

Y3 314

Y3

J7

307

7

Y3

Y3 307

See Fig. 4

8

Fig. 3 Scanner Unit (1/2)

205 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P Safety Mark

Ref. No. 401 402 403

DZJB000430 DZJB000432 DZHC000170

404

DZJA001439

405 406 407 408 409

DZJA001438 DZJA001384 DZJM001317 DZJM001347 DZKP000370

Frame, Lower Scanner Frame, CCD Cover 1, Harness Bracket, Dehumidifier Heater Bracket, Harness Cover, CCD Frame, Mirror 1 Slider Plate, Mirror 1 Spring

410

DZGM000011

411 412 413 414 415

Part Number

Part Name

New Parts C C C

Remarks

Destination All All All

C

All

C C C C C

All All All All All

Lamp, Scanning

C

All

DZTD000004 DZJC000381 DZJC000382 DZJC000383 DZTC000052

Sheet, Plate, Plate, Plate, Mirror

C C C C C

All All All All All

416

DZEA000088

PC Board, Inverter

C

All

417 418 419 420 421 422 423

DZJA001389 DZJC000384 DZJA001391 DZKP000280 DZTC000053 DZJM001319 DZJA001390

Base, Mirror 2 Plate, Pulley Holder, Front Mirror Spring, 2/3 Mirror Mirror 2 Guide, Lamp Harness Holder, Rear Mirror

C C C C C C C

All All All All All All All

424

FFPCP0034

Heater

C

All

425

DZHD000036

Sleeve, Heater

C

All

426

FFPTE2259

Label, HV

C

All

427 428

PJZNF3100PK DZJN000093

CCD Unit Rubber, CCD Frame

All

429 430 308 2811 2829 2830 2834 J6 X4 X8 Y2 Y3

DZJK000045 DZJK000046 DZLC000001 DZFP001622 DZFP001594 DZFP001639 DZFP001640 XUC3VM XTB3+20GFJ XTB3+8GFJ XTB3+6FFJ-RP XTW3+6LFJ

Clamp Clamp Pulley, Idler Harness, CCD Harness, INV Harness, PTC-AC 1 Harness, PTC-AC 2 E-Ring Screw Screw Screw Screw

N C C C C C C C C C C C C C

Reflective Wire Lock Rear Wire Holder Front Wire Holder 1

All All All All All All All All All All All All All

206 Ver. 1.0

OCT 2006

A

B

C

DP-8020E/8020P/8016P E

D

Y3 420

423

421

A

411

Y3

420 420

Y3 J6

Y3

426 412

421 422 308

2

X8

419

413 Y3

420 407

Y3 408

1

410

412

408

X8

418

417

415

3

414

408 308 J6

409 408 416

2811

4

X4 427

409

2829

Y3

A

404

425 406

410 Y2

2830

5

424

Y3

Y3 429

403

405 430

428 6

Y3 402

425

404

424 2834

7

401

8

Fig. 4 Scanner Unit (2/2)

207 Ver. 1.0

OCT 2006

5.4. Safety Mark

DP-8020E/8020P/8016P

Control Panel Unit Ref. No.

501

502

503

Part Number DZNA001161 DZNA001158 DZNA001155 DZNA001164 DZNA001159 DZNA001156 DZNA001153 DZNA001162 DZNA001160 DZNA001157 DZNA001154 DZNA001163 DZJE001218 DZJE001219 DZJE001165 DZJE001221 DZJE001175

504* CR2032

505

506 507 508 509

510

DZJE001173 DZJE001213 DZJE001214 DZJE001216 DZNA001042 DZKB000762 DZKB000641 DZKB000796 DZKB000927 DZKB000929

Part Name

New Parts

Remarks

For DP-8016P

Window, Panel

N

For DP-8020P*

For DP-8020E

Cover, Panel

C

Holder, Battery

C

Battery

C

Cover, Key

C

Key Key, Stop Key, Reset Key, Start

C C C C

C

Keys, Numerical

DZKB000928

Destination PF PK PU,PUG,Other PT PF PK PU,PUG,Other PT PF PK PU,PUG,Other PT PF PK PU,PUG,Other PT All All

For DP-8020E/8020P* AUR, Other YVR AER AVR For DP-8020E/8020P* All All All All For DP-8020E/8020P* PU, PUG For DP-8016P All PF For DP-8020E/8020P* Except PF, PU, PUG All All All

511 512 513

PJBCB0018Z-1 DZKB000930 DZKP000365

Key, Zoom Key, Function Spring, Speaker

C C C

514

DZHP010070

Assembly, Speaker

C

All

515 516 517 518

DZNA001040 PJBCB0016Z DZKP000385 DZNA001051 MGG03204Z03

Lamp, Active Key, Contrast Plate 1, Ground Cover, Harness Protection LCD Module Holder, LCD Key, A Key, B

C C C C C C C C

All All All All All All All All

519 520 521 522

DZNA001044 DZKB000931 DZKB000669

* Notice: California only: This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material - special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate

208 Ver. 1.0

OCT 2006

A

B

C

DP-8020E/8020P/8016P E

D

506

538

505

537 539

1

501

508

507

510

S6 511 502

2

509 Q8

A

512

504*

503

515

518

2916

2917

517

3

B

521

519

516

522

2906

520

523

X8

B A

522

681

X8

524

527

4

522

525

528

513

2904

526

514

X8

2924

681

2923 681

2905 5

X8 534 529

530

531

6

532

2907

533

535

2918

7

536

X8

X8 S6

X8

8

Fig. 5 Control Panel Unit

209 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P Safety Mark

Ref. No. 523 524 525 526 527 528

DZNA001046 DZNA001047 DZNA001048 DZNA001049 DZKB000924 DZKB000923

Key, Key, Key, Key, Key, Key,

529

DZJE001167

Cover, Control Panel Base

C

All

530

DZJE001169

Cover, Control Panel Sub Base

C

All

Part Number

Part Name Copy Fax/E-mail Scan/File Print Touch 3 Touch 2

New Remarks Destination Parts C For DP-8020E/8020P* All C For DP-8020E/8020P* All C For DP-8020E/8020P* All C All C All C All

532 533 534 535

DZNA001053 DZJE001177 DZJA001365 DZJA001366

Sheet, Keyboard Base Cover, Keyboard Bracket, Right Keyboard Bracket, Left Keyboard

C C C C

For DP-8020E/8020P* (English) For DP-8020E/8020P* (French) For DP-8020E/8020P* (German) For DP-8020E/8020P* For DP-8020E/8020P* For DP-8020E/8020P* For DP-8020E/8020P*

536

DZJE001179

Cover, Keyboard Lower

C

For DP-8020E/8020P* All

537

DZJE001171

Cover, Aperture

C

For DP-8016P

DZNA001055 531

DZNA001058

Sheet, Keyboard

C

DZNA001059

PJYPF3182PU PJYPF3182PF PJYPF3182PK PJYPF3182PT PJYPF3181PU PJYPF3181PB 538

PJYPF3181PF PJYPF3181PK PJYPF3181PT PJYPF3180PU

Assembly, Control Panel

N

PJYPF3180PB PJYPF3180PF PJYPF3180PK PJYPF3180PT 539 DZNM000005 681 DZJK000023 2904 DZEC102911R 2905 DZEC102912R 2906 DZEC102913R 2907 DZEC103049R 2916 DZFP001627 2917 DZFP001628 2918 DZFP001629 2923 DZFP001533 2924 DZFP001534 Q8 XTB3+8GFN S6 DZPA000086 X8 XTB3+8GFJ

Logo, Panasonic Clamp PC Board, PNL1 PC Board, PNL2 PC Board, PNL3 PC Board, PNL4 Harness, PNL1-PNL3 A Harness, PNL1-PNL3 B Harness, PNL1-PNL4 Harness, PNL2 1 Harness, PNL2 2 Screw Screw Screw

C C C C C C C C C C C C C C

All All All All All All All

All

PU, PB, PS, For DP-8016P PF PK PT PU, PA, PP, For DP-8020P* PF PK PT PU, PA, PP, For DP-8020E PF PK PT All All RTL/PbF All All All For DP-8020E/8020P* All All All All All All All All All

PUG, PA, PM, PP, PY

PUG PB, PM, PS, PY

PUG PB, PM, PS, PY

210 Ver. 1.0

OCT 2006

A

B

C

DP-8020E/8020P/8016P E

D

506

538

505

537 539

1

501

508

507

510

S6 511 502

2

509 Q8

A

512

504*

503

515

518

2916

2917

517

3

B

521

519

516

522

2906

520

523

X8

B A

522

681

X8

524

527

4

522

525

528

513

2904

526

514

X8

2924

681

2923 681

2905 5

X8 534 529

530

531

6

532

2907

533

535

2918

7

536

X8

X8 S6

X8

8

Fig. 5 Control Panel Unit

211 Ver. 1.0

OCT 2006

5.5. Safety Mark

DP-8020E/8020P/8016P

Paper Transportation Ref. No. 601 602 603 604

DZLA000371 DZLF000748 DZLM000006 DZLM000215

606

DZJA001405

607

DZKL000083

608

DZKL000084

609

DZKQ000111

611 614 615 616 617 618 619 620 621 622 623 624 625 626 627 629 631 632 633 634 635 636 637 638 639 640 641 642 643 647 649 650 651 653 654 655

DZKK000126 DZKQ000110 DZJF000650 DZJF000651 DZJF000668 DZLM000213 DZLA000363 DZKG000384 DZLF000711 DZLG000035 DZLA000360 DZLF000710 DZKQ000107 DZKG000383 DZJA001402 DZLA000366 DZKK000129 DZJA001420 DZKG000405 DZJF000655 DZJM001345 DZJM001344 DZJM001357 DZJF000653 PJDGC0186Z PJBAC0044Z PJBVC0149Z DZLM000050 DZJH000127 DZJC000387 DZJL000397 DZJF000652 DZLM000212 PJUSC0077Z DZGK000471 DZJM001343

Part Number

Part Name Roller, Registration Gear, 18 Timing Roller Bushing 2, P6L5 Collar, Timing Roller Bracket, Registration Sensor Lever, Paper Exit Sensor Actuator, Registration Sensor Spring, Registration Sensor Latch, Arm Spring, Latch Guide, Upper Guide, Front Guide, Feed Roller Bushing Roller, Pickup Shaft, Pickup Gear, Pickup Idler Clutch, One-way Roller, Feed Gear, Pickup Drive Spring, Pickup Shaft, Feed Bracket, Pickup Roller, Reverse Arm, Reverse Bracket, Reverse Shaft, Reverse Guide, Lower Film, Lower Guide Film, Rear Guide Film, Front Guide Guide, Duplex Gear, Feed Case, Clutch Spring, Clutch Bushing, P6L8 Collar, Stopper Guide, Shaft Plate, Pressure Tray, Guide Bushing, Left Spacer, Feed Shaft, Reverse Roller Film, Separation Roller

New Parts C C C C

Remarks

Destination All All All All

C

All

C

All

C

All

C

All

C C C C C C C C C C C C C C C C C C C C C C C C N N N C C C C C C N C C

All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All

PM

PM

PM

212 Ver. 1.0

OCT 2006

A

B

C

S9

Y3

606 680

607

698

2820

699

688

G6

680

1

131

608

614

604

694

609 681

DP-8020E/8020P/8016P E

D

601

Y2

602

699

611

603 665 S9

Y3

H7

2820 131 617 666 667

698 695 S9 S9

Y3 668

S9

627 S9

618 633

631

S9

2

616 620

3

615 Y3

S9

621

629

X8

S9 619

634 686 632

K5

626 690

4

625 S9

622 698

635

S9 624

Y3

623 X8

639 641 640 643 682

5

670 642 X1 638

J7

651

636

692

643

654

655

637

647 X8

696

658

X1

691

X8

684

X8

662 657

6

689

659 653

2326 671 651 656

685 649

X8 S9 642 7

661 685 2839 131

650 660

664 G6

X8 663 697 Y3

8

2840

Y3

Fig. 6 Paper Transportation

213 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P Safety Mark

Ref. No. 656 657 658 659 660 661 662 663 664 665 666 667 668 670 671 680 681 682 684 685 686 688 689 690 691 692

DZKQ000116 DZKQ000117 DZLA000365 DZJF000654 DZKL000085 DZJA001407 DZKP000375 DZJA001406 DZKN000420 DZJB000438 DZJM001378 DZJM001381 DZJM001388 DZNE000132 DZHP012149

Spring, Front Spring, Rear Roller, Separation Guide Actuator, No Paper Bracket, Rear Guide Ground Spring Bracket, Front Guide Spring, Fulcrum Bracket, Feed Film, Guide Sheet, Guide Film, Guard Spacer Roller Feed Bypass Assy

DZJK000004 DZJK000023 PJDHC0019Z DZJP000065 PJBVC0151Z DZKN000416 DZJA001427 DZLA000415 DZHP010738 DZHP010737 DZJM001387

Clamp Clamp Cam, Feed Board, Pad Spring Spring, Reverse Assembly, Latch Bracket Roller, Feed Torque Limiter 1 Torque Limiter 2 Damper

694

L9EAAK000009

Clutch, Micro 2

C

All

695

L9EAAK000010

Clutch, Micro 1

C

All

C

All

C C C C C

All All All All All

696 697 698 699 131 2326

Part Number

PJZFF3180PB DZKG000419 FFPMQ0649 DZJK000057 DZAL000211 DZPK000017

2820 DZFP001597 2839 2840 G6 J7 H7 K5 S9 X1 X8 Y2 Y3

DZFP001608 DZFP001616 FFPFJ0039B XUC4VM FFPFJ0041B XUC5VM FFPFJ0033B DZJM000171 or XTB3+10GFJ XTB3+8GFJ XTB3+6FFJ-RP XTW3+6LFJ

Part Name

New Parts C C C C C C C C C C C C C C C C C N C C C C C C C C

Remarks

PM

PM PM PM

Destination All All All All All All All All All All All All All All All All All All All All All All All All All All

Assembly, Feed Roller Shaft Pin, Fulcrum Bushing Clamp Sensor, Photo Washer Harness, Paper Tray Sensor Harness, HEPESEN Harness, Frame Ground Snap Ring E-Ring Snap Ring E-Ring

C

All

C C C C C C

All All All All All All

Snap Ring

C

All

Screw Screw Screw Screw

C C C C

All All All All

214 Ver. 1.0

OCT 2006

A

B

C

S9

Y3

606 680

607

698

2820

699

688

G6

680

1

131

608

614

604

694

609 681

DP-8020E/8020P/8016P E

D

601

Y2

602

699

611

603 665 S9

Y3

H7

2820 131 617 666 667

698 695 S9 S9

Y3 668

S9

627 S9

618 633

631

S9

2

616 620

3

615 Y3

S9

621

629

X8

S9 619

634 686 632

K5

626 690

4

625 S9

622 698

635

S9 624

Y3

623 X8

639 641 640 643 682

5

670 642 X1 638

J7

651

636

692

643

654

655

637

647 X8

696

658

X1

691

X8

684

X8

662 657

6

689

659 653

2326 671 651 656

685 649

X8 S9 642 7

661 685 2839 131

650 660

664 G6

X8 663 697 Y3

8

2840

Y3

Fig. 6 Paper Transportation

215 Ver. 1.0

OCT 2006

5.6. Safety Mark

DP-8020E/8020P/8016P

Automatic Duplex Unit Ref. No. 703 704 705 706 707 708 709

DZGT000032 DZJL000404 DZJH000128 DZLF000745 DZKN000418 DZKN000181 DZLM000133

710

DZLF000746

711 712 713 714 715 716 717

DZLA000368 DZLA000367 DZKP000376 DZKP000378 DZKP000377 FFPLP0769C DZFP000747

Brush, Discharge Plate, Discharge Spacer, BTR Ring Gear, BTR 27 Spring, BTR Spring, Timing Roller Bushing, Bias Transfer Gear, 17 Pinch Timing Roller Roller, Bias Transfer Roller, Pinch Timing Lead, HV Bias Transfer Lead, Plate Discharge Lead, Pinch Roller Timing Spring, Terminal Resistor, 200M ohm

718

DZJF000659

Guide, Transfer

C

All

719 720 723 725

DZKK000130 DZKK000131 DZKL000086 DZJA001425

Arm, Rear Frame Arm, Rear Cover Lever, Release Stopper, Release

C C C C

All All All All

726

DZJE001202

Cover, Printer

C

All

727 728 729 730 731 732 733 734 735 736 737 738 739 740 741 743 744 745 746 748

DZKP000379 DZLA000369 DZKN000417 DZKQ000120 DZKL000088 DZJF000661 FFPMQ0648 DZLM000134 DZLA000370 DZLB000060 DZLK000031 DZLF000747 DZJF000656 DZLF000354 DZLF000342 DZKK000090 DZHP009941 DZHP009942 DZHP009943 PJVZF2121PB

Bracket, Pinch Roller Roller, Duplex Pinch Spring, Release Spring, Actuator Actuator, Duplex Paper Guide, Duplex 2 Bushing, Front Bushing, Rear Roller, Duplex Feed Pulley, 19 Duplex Belt, Timing T1 Gear, 15 Duplex Guide, Duplex Gear, E25 Gear, E20 Stopper, Tray Bracket, Front Cover Bracket, Rear Cover Plate, Duplex Drive Guide Bias Transfer Assy

C C C C C C C C C C C C C C C C C C C C

Part Number

Part Name

New Parts C C C C C C C

Remarks

All All All All All All All

C C C C C C C C

Destination

All PM

All All All All All All All

For DP-8020E For DP-8020E For For For For For For For For For For For For

DP-8020E DP-8020E DP-8020E DP-8020E DP-8020E DP-8020E DP-8020E DP-8020E DP-8020E DP-8020E DP-8020E DP-8020E

For DP-8020E

All All All All All All All All All All All All All All All All All All All All

216 Ver. 1.0

OCT 2006

A

B

C

DP-8020E/8020P/8016P E

D

X8

1

748 709 716

711 713 707 708 718

709

2

703

X8

712

709 706

710

S6

705

709

J6

X8 708

727

707

728

3

X1 704

714 X8

717

131 2844 730

X8 K9

715

737 736

K9

X8

732 731

734

4

743 G6 719 745

X8

S9

X8

738

720

S9

740

G6

736

735 734

C2

739 X8

S9

S9

746

725

5

Y3

741

680 723

735 X8

733

S9 733

6

729 X8

7

744

680 726 8

Fig. 7 Automatic Duplex Unit

217 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P Safety Mark

Ref. No. 131 680 2844 C2 G6 J6 K9 S6 S9 X1 X8 Y3

Part Number

Part Name

DZAL000211 DZJK000004 DZFP001607 DZPB000020 FFPFJ0039B XUC3VM FFPFJ0043B DZPA000086 FFPFJ0033B DZJM000171 XTB3+10GFJ XTB3+8GFJ XTW3+6LFJ

Sensor, Photo Clamp Harness, DUPSEN Screw Snap Ring E-Ring Snap Ring Screw or

New Remarks Parts C C C For DP-8020E C C C C C

Destination All All All All All All All All

Snap Ring

C

All

Screw Screw Screw

C C C

All All All

218 Ver. 1.0

OCT 2006

A

B

C

DP-8020E/8020P/8016P E

D

X8

1

748 709 716

711 713 707 708 718

709

2

703

X8

712

709 706

710

S6

705

709

J6

X8 708

727

707

728

3

X1 704

714 X8

717

131 2844 730

X8 K9

715

737 736

K9

X8

732 731

734

4

743 G6 719 745

X8

S9

X8

738

720

S9

740

G6

736

735 734

C2

739 X8

S9

S9

746

725

5

Y3

741

680 723

735 X8

733

S9 733

6

729 X8

7

744

680 726 8

Fig. 7 Automatic Duplex Unit

219 Ver. 1.0

OCT 2006

5.7. Safety Mark

DP-8020E/8020P/8016P

Electrical Parts Ref. No. 801 802 803

DZHD000038 DZJA001379 DZMC000824

Cover, PS Bracket, PS Bracket, Right

804

M0CE00000028

HDD Unit

C

All

805 806 807 808 809 810 811 812 813

DZJE001207 DZMC000825 DZJC000380 DZJA001436 DZJA001437 DZJA001378 DZJA001443 DZKP000374 DZJA001377

Cover, HDD Handle Bracket, PS SW Bracket, RLB PCB SW Bracket, RLB PCB Base, PS Bracket, MJR PCB Spring, LAN Bracket, PS Cover

C C C C C C C C C

All All All All All All All All All

814

DZCC000006

Switch, Power

C

All

815

L6FALEGK0018 DZGG000075

Fan, Rear

N C

For DP-8020E/8020P* All For DP-8016P

816

DZGG000076

Fan, PS

C

All

817

L2BA00000007

PC Board, HSU

C

All

818

DZCC000011

Switch, Power

C

All

819

G0A173J00001

Coil 1

C

Except PU, PT, PK, PUG

820

G0A352H00002 or DZDG000177

Coil 2

821

DZTK000002

Counter

C

822 823 824

DZJH000084 DZHE000059 DZJB000449

Supporter, PC Board Duct, Exit Holder, Filter

C C C

825

DZHE000060

Filter, Ozone

C

826 827 828

DZMC000827 DZPA000093 DZHE000057

Guard, Fan Screw Cover, Fan

C C C

LSU Unit

C

Part Number

Part Name

New Parts C C C

Except PU, PT, PUG

N

LPA3612F-BR 830

FFPTE1621B

Label, HV Caution

C

832 833 680 681

DZJH000063 DZJF000462 DZJK000004 DZJK000023

Spacer, PCB Guide, Card Clamp Clamp

C C C C

937

DZPA000091

Screw

C

939

DZMM000038

Foot, Damping

C

940

DZJK000070

Clamp

C

941

DZJB000459

Base, CHC

C

Destination All All All

C

LPA3612F-R 829

Remarks

PB, PF, PM, PP, PS Europe only All All PM

All All All All PU, PUG, PK, PT Except PU, PUG, PK, PT All

All For DP-8020E/8020P* All All All Except PU, PT, PUG, PK Except PU, PT, PUG, PK All Except PU, PT, PUG, PK

220 Ver. 1.0

OCT 2006

A A

B B

C C

DP-8020E/8020P/8016P E E

D D

X3 X3

11

801 801 680 680 Y3 Y3

Y3 Y3

2901 2901

802 802

937 937

830 830 940 940

X3 X3

22

Y3 Y3 819 819

939 939

941 941 810 810

Y4 Y4

825 825

815 815

820 820

3128 3128

828 828

2804 2804 Y3 Y3

Y6 Y6

823 823

826 826

824 824

Y3 Y3

809 809 X3 X3

Y4 Y4

Y3 Y3 833 833 2801 2801

2805 2805

2902 2902

X3 X3 829 829

Y3 Y3

827 827

3116 3116 806 806 Y3 Y3

808 808

813 813

55

805 805

814 814

Y3 Y3

2903 2903

Y3 Y3

681 681 803 803

Y3 Y3

822 822

832 832

44

2803 2803

811 811 Y6 Y6

822 822

33

Y3 Y3 X4 816 816 X4

Y3 Y3

Y3 Y3 Y3 Y3 806 806

807 807

812 812

818 818

804 804

Y3 Y3

Y3 Y3 66

3116 3116 681 681

2802 2802

77

817 817 Y3 Y3 680 680

681 681 821 821

2806 2806 88

Fig. 8 Electrical Parts

221 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P Safety Mark

Ref. No. 2801 2802 2803 2805 2806

Part Number Depends on Destination DZEC104147 DZEC102176R DZEC103692

DZEC102751R Depends on 2901 Destination

Part Name

New Parts

PC Board, SC

N

PC PC PC PC

N C C C

Board, Board, Board, Board,

SPC DC FRM8 WTS

PC Board, PS

C

2902

Depends on Destination

PC Board, MJR

C

2903

Depends on Destination

PC Board, FXB

C

3116 3128 X3 X4 Y3 Y4 Y6

DZJK000068 DZJH000026 XYN3+F8FJ XTB3+20GFJ XTW3+6LFJ XTB3+32GFJ XTW3+6LFJR

Clamp 2, Locking Spacer, PCB Screw Screw Screw Screw Screw

C C C C C C C

Remarks See Sect. 5.17 PC Boards (RTL/PbF) RTL/PbF RTL/PbF RTL/PbF

Destination

All All Europe only All

See Sect. 5.17 PC Boards See Sect. 5.17 PC Boards (RTL/PbF) See Sect. 5.17 PC Boards (RTL/PbF) All All All All All All All

222 Ver. 1.0

OCT 2006

A A

B B

C C

DP-8020E/8020P/8016P E E

D D

X3 X3

11

801 801 680 680 Y3 Y3

Y3 Y3

2901 2901

802 802

937 937

830 830 940 940

X3 X3

22

Y3 Y3 819 819

939 939

941 941 810 810

Y4 Y4

825 825

815 815

820 820

3128 3128

828 828

2804 2804 Y3 Y3

Y6 Y6

823 823

826 826

824 824

Y3 Y3

809 809 X3 X3

Y4 Y4

Y3 Y3 833 833 2801 2801

2805 2805

2902 2902

X3 X3 829 829

Y3 Y3

827 827

3116 3116 806 806 Y3 Y3

808 808

813 813

55

805 805

814 814

Y3 Y3

2903 2903

Y3 Y3

681 681 803 803

Y3 Y3

822 822

832 832

44

2803 2803

811 811 Y6 Y6

822 822

33

Y3 Y3 X4 816 816 X4

Y3 Y3

Y3 Y3 Y3 Y3 806 806

807 807

812 812

818 818

804 804

Y3 Y3

Y3 Y3 66

3116 3116 681 681

2802 2802

77

817 817 Y3 Y3 680 680

681 681 821 821

2806 2806 88

Fig. 8 Electrical Parts

223 Ver. 1.0

OCT 2006

5.8. Safety Mark

DP-8020E/8020P/8016P

Frame Parts Ref. No. 901 902 903 904 905 906 907 908 909 910 911 912 913 914

DZJB000442 DZJA001371 DZJA001370 DZJA001369 DZJA001368 DZMC000823 DZJB000441 DZJA001372 DZJA001374 DZMC000822 DZKJ000017 DZJC000378 DZKK000119 DZJA001373

Frame, Right Scanner Post, Rear SC Post, Front SC Frame, SC Bracket, LSU 2 Bracket, Center Frame, Left Scanner Bracket, LSU 1 Bracket, Bottle Frame, Front Plate, DIAL Plate, SA Lever, SA Bracket, Toner

915

DZJD000039

Plate, Engine FL

C

All

916

DZJA001367

Bracket, Connector

C

All

918

DZJD000038

Plate, Engine FU

C

All

920 922 923 924 926 928 929 930 931 932

DZKP000367 DZKP000366 DZJB000445 DZJB000443 DZJB000440 DZJB000444 DZKN000410 DZJD000044 DZMC000821 DZKP000380

Spring, PS Cover Spring, PS Cover, CST Bracket, Inlet Bracket, SPC PCB Bracket, Rear Spring, Contact Holder, Contact Spring Plate, Base Lead, BTR Frame

C C C C C C C C C C

All All All All All All All All All All

933

DZJD000043

Holder, Rear Engine

C

All

934 935 936

DZJB000421 DZKP000368 FFPKD07791

Frame, Center Spring, Paper Tray Ground Bracket, Heater

C C C

937

DZPA000091

Screw

C

938

DZPA000092

Screw

C

939

DZMM000038

Foot, Damping

C

941

DZJB000459

Base, CHC

C

942 943 944

DZHE000055 DZHE000056 DZJB000426

Duct, Upper Duct, Lower Base, Paper Tray L

C C C

All All All Except PU, PT, PUG All Except PU, PT, PUG Except PU, PT, PUG All All All

945

DZFA000098

Inlet

C

All

Part Number

Part Name

New Parts C C C C C C C C C C C C C C

Remarks

Destination All All All All All All All All All All All All All All

224 Ver. 1.0

OCT 2006

A

B

C

DP-8020E/8020P/8016P E

D

Y3

952

901

952

1

Y3 920 Y3

X3

922

Y3

902

Y3 Y3

Y3 924

923

Y3 2

903

Y3

923

947

951

934

946

680

926 945 Y3

904 681 Y3

Y10 Y3

3

905

681

680

Y3

908 906

Y3 Y3

681

3116

4

907 3007

935

953 929

928

Y3 Y3

Y7

909

930

Y3

918 942 943

933

Y3

X6

932

910

Y3

911 938

Y7

2819

5

912 Y3

X6

913

916

Y2

Y3 938

936

3115 681

950

425 424

3116

915 3116

Y3

914 Y3

6

X8

2831 RLB CN173

3011

931

7

944

3115 X8

3016

3016

948

3012 3017

X8

3017

8

Fig. 9 Frame Parts

225 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P Safety Mark

Ref. No. 946

Part Number DZFP001650

Part Name Inlet Harness

New Parts C

Remarks

Destination All

For DP-8020E/8020P* All All All All PA, PB, PF, PM, PP, PS, PY All

947 948 950 951

DZJL000023 DZJN000076 DZJM001363 DZJB000463

Plate, Ground Gum, Paper Tray Film, Airflow Control Guide, Counter

C C C C

952

PJHSC0025Z

Gasket

C

953

PJBUC0105Z

Plate, Ground Drive

C

424

FFPCP0034

Heater

C

All

425 680 681 2819 2831 3007 3011 3012 3016 3017 3115 3116 X3 X6 X8 Y2 Y3 Y7 Y10

DZHD000036 DZJK000004 DZJK000023 DZFP001595 DZFP001641 DZMB000024 DZJB000427 DZJB000428 DZLA000198 DZJF000489 DZJK000067 DZJK000068 XYN3+F8FJ XTB3+8JFJ XTB3+8GFJ XTB3+6FFJ-RP XTW3+6LFJ XNC3FJ XYN4+F6FJ

Sleeve, Heater Clamp Clamp Harness, WTS Harness, PTC-AC 3 Bracket, Rear Lower Right Base, Right Paper Tray Bracket, Paper Tray Base Roller, Paper Tray Leg, Gum Clamp Clamp Screw Screw Screw Screw Screw Nut Screw

C C C C C C C C C C C C C C C C C C C

All All All All All All All All All All All All All All All All All All All

226 Ver. 1.0

OCT 2006

A

B

C

DP-8020E/8020P/8016P E

D

Y3

952

901

952

1

Y3 920 Y3

X3

922

Y3

902

Y3 Y3

Y3 924

923

Y3 2

903

Y3

923

947

951

934

946

680

926 945 Y3

904 681 Y3

Y10 Y3

3

905

681

680

Y3

908 906

Y3 Y3

681

3116

4

907 3007

935

953 929

928

Y3 Y3

Y7

909

930

Y3

918 942 943

933

Y3

X6

932

910

Y3

911 938

Y7

2819

5

912 Y3

X6

913

916

Y2

Y3 938

936

3115 681

950

425 424

3116

915 3116

Y3

914 Y3

6

X8

2831 RLB CN173

3011

931

7

944

3115 X8

3016

3016

948

3012 3017

X8

3017

8

Fig. 9 Frame Parts

227 Ver. 1.0

OCT 2006

5.9. Safety Mark

DP-8020E/8020P/8016P

Fuser Unit Ref. No.

Part Number

Part Name

New Parts

Remarks

Destination

1001 DZJF000702

Guide, SC PCB

C

All

1002 DZKP000373 1003 DZLA000083 1005 DZKP000371

Plate, Idle Spring Roller, Idle Plate, Ground

C C C

All All All

1006 DZJE001199

Cover, Rear Fuser

C

All

1007 DZJE001200

Cover, Front Fuser

C

All

1008 DZKN000407 1009 DZLA000357

Spring, Pressure Roller, Idle 2

C C

All All

1010 DZJF000645

Guide, Pressure Roller

C

All

1011 1012 1013 1014 1016 1017 1018 1019 1020 1021 1022 1023 1024

Spring, Opening Sheet A Knob, JAM Release Plate, Knob Roller, ADU Spring, Idle ADU Plate, Rear Pressure Plate, Front Pressure Bushing, Pressure Roller Roller, Pressure Spring, Ground Guide, Front Plate, Ground 2

C C C C C C C C C C C C C

All All All All All All All All All All All All All

1025 DZJE001223

Frame, Lower Assy

C

All

1026 DZNK005265

Label, High Temperature

C

All

DZKQ000109 DZHD000039 DZLF000705 DZJA001409 DZLA000358 DZKN000408 DZKK000124 DZKK000122 DZLM000132 DZLA000362 DZKN000409 DZJF000649 DZKP000372

PJZSF3180PU PJZSF3180PB 1027

Fuser Unit

PJZSF2121PU2

N

PJZSF2121PB2 1028 131 2838 S6 S9 X3 X7 X8 Y5 Y7

PJSCC0015Z DZAL000211 DZFP001606 DZPA000086 FFPFJ0033B DZJM000171 XYN3+F8FJ XYN3+F14FJ XTB3+8GFJ XSN3+W10FJ XNC3FJ

or

For DP-8020E For DP-8020E

PM PM

PU, PUG, For DP-8020E/8020P* Except PU, PUG, PU, PUG, For DP-8016P Except PU, PUG, All All All All

Brush, Antistatic Sensor, Photo Harness, Thermistor 1 Screw

C C C C

Snap Ring

C

All

Screw Screw Screw Screw Nut

C C C C C

All All All All All

PT PT PT PT

228 Ver. 1.0

OCT 2006

A

B

C

DP-8020E/8020P/8016P E

D

1

1002 1027

1003

X8

1005

2

1006

1028

1007 X8

3

1009

Y5 1001

1011

4

1008 1012

1010

1008 S9

5

X7

S9 1013 1014

Y7

1018

2838

X8

131 1017

1020 1016

X8 6

1023 1024

1021

S6

X3 1026

7

1020 Y7

1025

1019

1022

8

Fig. 10 Fuser Unit (1/2)

229 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P Safety Mark

Ref. No. 1101 1102 1103 1104 1105 1106 1107 1108 1109

Part Number

Part Name

DZJE001194 DZLF000706 DZLM000052 DZJN000088 DZJF000646 DZHC000168 DZKQ000108 DZJB000434 DZJM001406

Cover, Exit Roller Gear, Exit Roll Bushing, P6L5 Conductor Roller, Exit 2 Guide, Fuser Roller Actuator Spring, Actuator Base, Separator Separator

New Parts C C C C C C C C C PM

Remarks

Destination All All All All All All All All All

1110 DZJB000429

Frame, Upper Fuser

C

All

1111 1112 1113 1114 1115

Plate, Rear Spring Gear, E39 Fuser Roller Ring Bushing, Fuser Roller Roller, Fuser

C C C C N

PM PM

All All All All All PU, PT, PUG Other All

DZJA001394 DZLF000199 DZPJ000004 DZLM000208 DZLA000418 DZGN000052 1116 DZGN000053 1117 DZJA001396

Lamp, Fuser

C

Plate, Terminal 1

C

1118 K5X216BG0002

Fuse, Thermal

C

1119 DZJA001397

Plate, Terminal 2

C

K0BDB0000080

N

1120

Thermostat DZDX000003

1121 1122 1123 1124 1125 1126 1127 1128 1009 1402 2838 S9 X1 X3 X8

DZJA001398 DZJC000385 DZJC000386 DZJA001393 DZBL000061 DZJE001195 FFPLN0005 DZKK000121 DZLA000357 DZLL000005 DZFP001606 FFPFJ0033B DZJM000171 XTB3+10GFJ XYN3+F8FJ XTB3+8GFJ

C

or

PM

See Note

All All

See For See For

Note DP-8020E/8020P* Note DP-8016P

All

Plate, Terminal 3 Holder, Rear Lamp Holder, Front Lamp Plate, Front Spring Assembly, Thermistor Cover, Fuser Roller Spring Actuator 2 Roller, Idle 2 Wheel, Star Harness, Thermistor 1

C C C C C C C C C C C

Snap Ring

C

All

Screw Screw Screw

C C C

All All All

PM

All All All All All All All All All All All

Note: This part is subject to the U.S. Export Administration Laws and Regulations for export or re-export to the countries specified below. Countries subject to embargo are: Cuba, Iran, Iraq, Libya, North Korea, Syria and Sudan. This list is subject to change without further notice. Purchaser of those countries are requested to order the Fuser Unit Assy instead of this part.

230 Ver. 1.0

OCT 2006

A

B

C

DP-8020E/8020P/8016P E

D

S9 1

1103 1102

1104

1106 1128

X8 1009

1107 1127

2

1103 S9

1109

1101

1105

1109

3

X8 X8

1110

1111 1402

1122 2838

1108 X8

X3

1121 X8

X8

1114

1124

X3

1120

4

X8

X1

X3

A

1113

1125

1123 1119 1118 X3

1126

1117

C

X8

1112

5

X8

1115

6

1113 A

X8 C

1114 B

7

1116

1116

B

8

Fig. 11 Fuser Unit (2/2)

231 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

5.10. Hopper Unit Safety Mark

Ref. Part Number No. 1201 DZHP009894 1202 DZML000478 1203 DZJB000422 DZJE001308 1208 DZJE001299 DZJE001180 1209 DZUJ000017 1212 DZJC000379 1213 DZJM001308 DQ-TUJ10K-PU 1216 DQ-TUJ10K-PK DQ-TU10J-PB PJZYF3184PU 1217 PJZYF3184PK DZJA001422 X6 XTB3+8JFJ X9 XTB3+8FFJ

Part Name Container, Toner Waste Tray, Spill Holder, Bottle Holder, Rear Bottle Cleaner, Bottle Shutter Guide, Bottle Shutter Film, Bottle Shutter Assembly, Toner Bottle (Available as Sales Item)

New Parts C PM C C N C C C C N C N

Hopper Unit

C C C

Screw Screw

PM

Remarks

Destination All All All PU, PUG PK Other All All All PU, PUG PK Other PU, PUG PK Other All All

232 Ver. 1.0

OCT 2006

A

B

C

DP-8020E/8020P/8016P E

D

1

1216 2

3

4

1208 X6

1209

X9

5

1213 1212

1203

6

1217 1202

See Fig. 13, 14 7

1201

8

Fig. 12 Hopper Unit

233 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

5.11. Developer Unit Safety Mark

Ref. No. 1301 1302 1303 1304 1305 1306

Part Number DZJN000086 DZJE001186 DZHE000058 DZMH000029 DZJE001181 DZGD000005

1307 DZNE000117 1308 1309 1310 1311 1312 1313 1315 1316 1317 1318 1319 1320 1321 1322 1323 1324 1325 1326 1327 1328 1329 1330 1331 1332 1333 1334 1335 1336 1337 1338 1339 1340 1341 1342 1343 1344 1345

DZUJ000019 DZJM001309 DZJA001376 DZJA001375 DZJB000420 DZKN000401 DZJM001315 DZJA001380 DZLF000701 DZJE001185 DZLF000702 DZKG000377 DZLF000703 DZKG000378 DZLM000157 PJDGC0170Z DZJL000394 DZHA000225 DZLF000699 DZLM000194 DZUF000009 DZLF000700 DZUF000010 DZJL000215 DZJM001311 DZUJ000021 DZJE001184 DZLM000205 DZUF000008 PJURC0055Z DZJB000424 DZLM000204 DZLF000697 DZLM000203 DZKN000398 PJDIC0011Z DZKG000376

Part Name Sheet, Toner Dispersion Cover, Developer Sponge, Developer Blade, Doctor Frame, Lower Roller, Magnetic Film, Paper Approach Guide Seal, Frame Sheet, Toner Shield, Rear Side Shield, Front Side Frame, Developer Spring, Joint Slider Plate, Front Bias Coupling 1 Cover, Gear Gear, Idle Shaft 1, Idle Gear 2, Idle Shaft 2, Idle Bearing, Screw Gear 2, Screw 2 Plate, Rear Bias Cover 2, Harness Gear, Screw 1 Bearing, Paddle Screw 1 Gear, Screw 2 Screw 2 Holder, TDC Sensor Film, Pipe Seal, Pipe Cover, Pipe Bearing, PL Screw Screw, Supply Pipe, Support Frame, Pipe Bushing, Joint Gear, Pipe 15 Bushing 2, Joint Spring, Coil Joint, Screw Shaft, DR

New Parts C C C C C C

Remarks

Destination All All All All All All

C

All

C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C

All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All

234 Ver. 1.0

OCT 2006

A

B

C

DP-8020E/8020P/8016P E

D

To Fig. 14

1333

1

H7 1343 H7

1342

1301

1334

1344 1335 1337

1345

S9

1346

X9

2

H7 1336 1339

1341

1304 1340 1360 H7 1351

1303

1302

1350

1357 1358

1355

1305

1338 X9

Y8 1318

1356

S9

X9 1309

1324 1321

1355

1308

1310 1313

1325

3

1354 X9 1352

1323

1317

4

1356

1323

1306

1353

1312 1359

1322

680

1348

1311

5

K5 1313 1320 1315

1319 2836

X9 1349

1316 1348

1307

X9 J8

1332

1331

X9 1347

To Fig. 14

6

1328 1330

X9

7

1329 1326

1328 1327 8

Fig. 13 Developer Unit

235 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P Safety Mark

Ref. Part Number No. 1346 DZLF000698 1347 DZHP009933 1348 DZLM000207 1349 L2DA00000126 1350 DZJC000395 1351 DZQJ000083 1352 DZHE000067 1353 DZHE000068 1354 DZHE000069 1355 DZHE000071 1356 DZHE000072

Part Name Gear, Pipe 15T Developer Unit Bearing, Mag Sensor, Toner Block Tape, Block Sponge, Cover L Sponge, Cover Angle Sponge, Cover S Seal, Developer Side Sponge, Developer Side Sponge, Doctor Blade Side A Sponge, Doctor Blade Side B Sponge, Cover M Bushing Screw Assy Clamp Harness, Toner Sensor Snap Ring E-Ring E-Ring

1357 DZHE000073 1358 DZHE000074 1359 1360 680 2836 H7 J8 K5 S9 X9 Y8

DZHE000070 PJZYF212500 DZJK000004 DZFP001604 FFPFJ0041B XUC7VM XUC5VM FFPFJ0033B DZJM000171 XTB3+8FFJ XTN3+10GFJ

or

New Parts C C C C C C C C C C C

Remarks

Destination All All All All All All All All All All All

C

All

C

All

C C C C C C C

All All All All All All All

Snap Ring

C

All

Screw Screw

C C

All All

236 Ver. 1.0

OCT 2006

A

B

C

DP-8020E/8020P/8016P E

D

To Fig. 14

1333

1

H7 1343 H7

1342

1301

1334

1344 1335 1337

1345

S9

1346

X9

2

H7 1336 1339

1341

1304 1340 1360 H7 1351

1303

1302

1350

1357 1358

1355

1305

1338 X9

Y8 1318

1356

S9

X9 1309

1324 1321

1355

1308

1310 1313

1325

3

1354 X9 1352

1323

1317

4

1356

1323

1306

1353

1312 1359

1322

680

1348

1311

5

K5 1313 1320 1315

1319 2836

X9 1349

1316 1348

1307

X9 J8

1332

1331

X9 1347

To Fig. 14

6

1328 1330

X9

7

1329 1326

1328 1327 8

Fig. 13 Developer Unit

237 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

5.12. Drum Unit Safety Mark

Ref. Part Number No. 1401 DZHD000040 1402 DZLL000005

Sheet, Radiation Wheel, Star

1403 DQ-H60J-PU

Drum, OPC

C

1404 1405 1407 1408 1409 1410 1411 1412 1413 1414 1415 1416 1417 1418 1419 1420 1421 1422 1424 1425 1426 1427 1428 1429 1430 1431 1432 1433 1434 1435 1436 1437 1438 1439 1440 1441 1442 1443 1444 1445

Bushing, OPC Plate, Nut Holder, OPC Drum Shaft Blade, Cleaning Roller, Spacer Felt, Front Cleaning Felt, Rear Cleaning Sponge, Cleaning Sponge, Long Cleaning Sponge, Short Cleaning Sheet, Splash Prevention Film, PDL PDL, WTB Bushing, Screw Gear, PDL Joint Screw, WT Screw, Drum Unit Fix Cap, WT Sponge, Cap Spring, Cap Pipe, WTB Handle, Cleaning Lever Lever, Cleaning Guide, Lever Sponge, Charge Holder, Charge Cover, Charge Grid, Charge Sheet, Blind Spring, Charge Holder, Charge Wire Holder, Rear Charge Cover, Rear Charge Base, Charge Cleaning Pad, Cleaning Base, Pad Frame, OPC Wire, Charge Case, Charge Shaft, OPC

C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C

DZJM001314 DZJL000362 DZJM001330 DZJN000085 DZJM001313 DZJP000063 DZJP000064 DZJM001325 DZJM001328 DZJM001329 DZJM001324 DZJM001333 DZJM001332 DZLM000211 DZLF000731 DZJM001326 DZPA000075 DZJM001331 DZJM000377 DZKN000178 DZJM001327 DZJM001341 DZJM001339 DZJL000403 DZJM001342 DZJM001373 DZHA000226 DZJL000400 DZHC000169 DZKN000415 DZJL000402 DZJM001372 DZHA000227 DZJM001337 DZJM001340 DZJM001338 PJUAC0215Y DZJL000401 DZJL000399 DZJL000398

Part Name

New Parts C C

Remarks

Destination All All

PM (Available as Sales Item)

PM PM PM PM

PM

PM

All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All

238 Ver. 1.0

OCT 2006

A

B

C

DP-8020E/8020P/8016P E

D

1448 From Fig. 13

1436

1

1440 1437

1438

1441

1433

1429

1440 1444

1439 1455

1443

1401

1428

1419 1418

1431 1432 1430

1454

1417

1434

1419 2837

1418

2

1451 1427

1435

3

1447

1416

4

1420

2807 1442 1404

1402

2836

1405 5

1450 1421

1452 1453

1426 1409

1425 X9

1412

1445 6

1403

1414 1415

1424 1407 X3

1411

1422

1408 1410

1412

7

1414 1413

X3 From Fig. 13 1449 8

Fig. 14 Drum Unit

239 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P Safety Mark

Ref. No. 1447 1448 1449 1450 1451 1452 1453 1454 1455 2807 2836 2837 X3 X9

Part Number PJZYF212D00 PJZYF212F00 PJZYF212E00 DZKP000225 DZKP000389 DZHC000173 DZHC000172 DZJM001375 PJZYF212CAZ DZEC102830R DZFP001604 DZFP001605 XYN3+F8FJ XTB3+8FFJ

Part Name Assembly, Charge Corona Assembly, OPC Frame Assembly, Process Unit Plate, Star Wheel Plate, Ground Sheet Plate Film, Charge Side Assembly, Cleaning Pad PC Board, PCL Harness, Toner Sensor Harness, PCL PCB Screw Screw

New Parts C C C C C C C C C C C C C C

Remarks

Destination All All All All All All All All All All All All All All

240 Ver. 1.0

OCT 2006

A

B

C

DP-8020E/8020P/8016P E

D

1448 From Fig. 13

1436

1

1440 1437

1438

1441

1433

1429

1440 1444

1439 1455

1443

1401

1428

1419 1418

1431 1432 1430

1454

1417

1434

1419 2837

1418

2

1451 1427

1435

3

1447

1416

4

1420

2807 1442 1404

1402

2836

1405 5

1450 1421

1452 1453

1426 1409

1425 X9

1412

1445 6

1403

1414 1415

1424 1407 X3

1411

1422

1408 1410

1412

7

1414 1413

X3 From Fig. 13 1449 8

Fig. 14 Drum Unit

241 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

5.13. Drive Unit Safety Mark

Ref. Part Number No. 1501 DZJA001413 1502 DZJA001414

Frame A, Bottle Drive Frame B, Bottle Drive

1503 PJWQF2121PB

Assembly, Bottle Motor

C

All

1504 1505 1506 1507 1508 1509 1510

Plate 2, Ground Gear, Toner Sensor Gear 3, Toner Idle Gear 1, Toner Idle Gear, Toner Drive Spring, Toner Gear 2, Toner Idle

C C C C C C C

All All All All All All All

1511 DNQ18AS14W26

Motor, Drive

C

All

1512 DZGB000045

Solenoid

C

1513 1514 1515 1516 1517

Belt 1, Timing Frame A, Main Drive Frame B, Main Drive Cover B, Main Drive Gear, Fuser Drive Assembly, Fuser Drive Plate Gear, Waste Toner Drive Gear 1, Waste Toner Idle Gear 2, Waste Toner Idle Gear 2, Fuser Idle Gear 3, Fuser Idle Gear 3, MG Gear 4, Fuser Idle Gear 1, Registration Idle Gear 2, Registration Idle Gear 3, Drum Gear 2, Drum Gear 2, Mag Coupling, Mag Spring, Mag Drive Shaft, Mag Drive Gear 1, Mag Joint, OPC Spring, OPC Drive Shaft, Drum Drive Gear 1, Drum Assembly, Bottle Drive Assembly, Main Drive

C C C C C

All All All All All

C

All

C C C C C C C C C C C C C C C C C C C C C C

All All All All All All All All All All All All All All All All All All All All All All

DZKP000384 DZLF000736 DZLF000739 DZLF000737 DZLF000735 DZKN000413 DZLF000738

DZLK000043 DZJA001395 DZJA001399 DZJA001401 DZLF000716

1518 DZHP009912 1519 1520 1521 1522 1523 1524 1525 1526 1527 1528 1529 1530 1531 1532 1533 1534 1535 1536 1537 1538 1539 1540

DZLF000718 DZLF000724 DZLF000719 DZLF000717 DZLF000721 DZLF000715 DZLF000722 DZLF000720 DZLF000723 DZLF000713 DZLF000707 DZLF000714 DZLN000022 DZKN000406 DZKG000382 DZLF000709 DZLN000007 DZKN000405 DZKG000381 DZLF000708 DZTY000312 DZTY000311

Part Name

New Parts C C

Remarks

Destination All All

For DP-8020E

All

242 Ver. 1.0

OCT 2006

A

B

C

DP-8020E/8020P/8016P E

D

131 2822 1540

Y3

1503

1509

1518 X8

1544

1

1506 1507

1511

X8

2822

1505

1504

1508

1501

Y9

2

1517 1539

1522

1556

1506

1510

2822

1523

1502 3

1555 1558

1503 1557

1524 1528

1525

1514 1548

1538

Y3 1529

1553

1525 1524

4

J8 1533

1549

1534 1551 1552

1536

1537

1530

1527

1515 1526 1519

1546 K5

1535 1547 1532 1531 1550 Y3

1516 1521 1520

X8 5

3F 6

1543 1512

1542

680 681

680

1545 1562

1559 1560 7

Y3 1561 1513

Y3 1554

K5 934

1541 8

Fig. 15 Drive Unit

243 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P Safety Mark

Ref. Part Number No. 1541 DZTY000314 DZTY000315 1542 DZTY000317 1543 DZTY000316 1544 SPM-3

Part Name Assembly, Feed Drive

New Parts C

Remarks

For DP-8020P*/8016P For DP-8020E For DP-8020E

Destination All All All All All

Assembly, Exit Drive A

C

Assembly, Exit Drive B Spacer

C C

1545 L9AAABFB0001

Solenoid

N

All

1546 1547 1548 1549 1550 1551 1552 1553 1554 1555 1556 1557 1558 1559 1560 1561 1562 131 680 681 934 2822 3F J8 K5 X8 Y3 Y9

Bearing 1 Bearing 2 Bearing 3 Bearing 4 Polyslider Pin 1 Pin 2 Pin 3 Bracket, Solenoid Fly Wheel Ground Spring Kit Drive, Ground Spring Polyslider Washer Spring, Arm Arm Solenoid, Damper Screw Sensor, Photo Clamp Clamp Frame, Center Harness, BSMT Screw E-Ring E-Ring Screw Screw Screw

C C C C C C C C N C C C C N N N N C C C C C C C C C C C

All All All All All All All All All All All All All All All All All All All All All All All All All All All All

DZLM000209 DZLM000210 DZLM000216 DZLM000217 DZPK000032 DZTT000614 DZTT000718 XPJ2D14WV PJUIC0310Z DZJG000013 PJZEF2121PU PJSDC0005Z FFPMV0001 PJBVC0150Z PJBLC0026Z PJCGC0003Z XYN26+F4FJ DZAL000211 DZJK000004 DZJK000023 DZJB000421 DZFP001603 XYN3+F5FJ XUC7VM XUC5VM XTB3+8GFJ XTW3+6LFJ XYN4+F8FJ

244 Ver. 1.0

OCT 2006

A

B

C

DP-8020E/8020P/8016P E

D

131 2822 1540

Y3

1503

1509

1518 X8

1544

1

1506 1507

1511

X8

2822

1505

1504

1508

1501

Y9

2

1517 1539

1522

1556

1506

1510

2822

1523

1502 3

1555 1558

1503 1557

1524 1528

1525

1514 1548

1538

Y3 1529

1553

1525 1524

4

J8 1533

1549

1534 1551 1552

1536

1537

1530

1527

1515 1526 1519

1546 K5

1535 1547 1532 1531 1550 Y3

1516 1521 1520

X8 5

3F 6

1543 1512

1542

680 681

680

1545 1562

1559 1560 7

Y3 1561 1513

Y3 1554

K5 934

1541 8

Fig. 15 Drive Unit

245 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

5.14. Paper Tray Safety Mark

Ref. No.

Part Number

DZMC000829 DZMC000828 DZML000480 1602 DZML000487

1601

1603 1604 1605 1606 1607 1609 1610 1611 1613 1616 1617 1619 1620 S9 X3 Y1

DZML000479 DZML000484 DZML000481 DZML000482 DZJF000414 DZLA000356 DZML000483 DZLF000465 DZJL000414 DZKG000420 DZJM001369 PJRCC0004Z DZJP000005 FFPFJ0033B XYN3+F8FJ XTW3+8PFJ

Part Name

New Parts

Cover, Sub Tray

C

Cover, Paper Tray

C

Base, Paper Tray Lever, Guide Guide, Front Guide, Rear Guide, E Roller, Paper Tray Plate, Bottom Gear, Tray Plate, Lift Assembly, Arm Shaft Film, Paper Guide Label, Sensor Plate, Pad Pressure Snap Ring Screw Screw

C C C C C C C C C C C C C C C C

Remarks For For For For

1st Paper Tray Other Paper Tray 1st Paper Tray Other Paper Tray

Destination All All All All All All All All All All All All All All All All All All All All

246 Ver. 1.0

OCT 2006

A

B

C

DP-8020E/8020P/8016P E

D

X3

1

1613

1616 1620

S9 2

Y1

1610 1604 Y1

1606

Y1

3

1605

1611 1609

1607 Y1

1619 4

1609

Y1 1617 Y1

5

1601

6

Y1 1603

1602

Y1

7

8

Fig. 16 Paper Tray

247 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

5.15. Automatic Document Feeder Safety Mark

Ref. No. 1701 1702 1703 1704 1705 1706 1707 1708 1709 1710 1711

Part Number

Part Name

New Parts C C C C C C C C C C C

DZMA003293 DZMA003291 DZJA000852 DZKN000271 DZJM000670 DZML000422 DZKR000032 DZML000507 DZHC000057 DZLF000077 DZML000499 DZML000432 1712 DZML000433 DZML000504

Cover, ADF Rear Cover, ADF Front Bracket, Substrate Spring, White Rear Base, ADF Tray, Original Lower Spring, Ground Tray, Original Front Actuator, Original Length F Gear, D14 Guide, Original Front Tray, Original Upper

C

1713 1714 1716 1717 1719 131 430 2832 2846 2851 X6 62 B1

Actuator, Original Width Guide, Original Rear Spring, Original Length Spacer Brush, Antistatic Sensor, Photo Clamp PC Board, SNS PC Board, ADF Harness, ADF SNS Screw Screw Screw, Silver

C C C C C C C C C C C C C

Snap Ring

C

S9

DZJM000676 DZML000500 DZKQ000071 DZJM001241 DZGT000007 DZAL000211 DZJK000046 DZEC102304R DZEC102303R DZFP001968 XTB3+8JFJ XTB3+6JFJ DZPB000007 FFPFJ0033B DZJM000171

or

Remarks

RTL/PbF

Destination All All All All All All All All All All All PU,PUG Other PK All All All All All All All All All All All All All All

248 Ver. 1.0

OCT 2006

A

B

C

DP-8020E/8020P/8016P E

D

1709

1714

1712 1716

1713

1711

1

S9 S9

2851 131 1716

1709

1708

2

1710 62 2832 2851

B1

131 3

1701

2851 B1 62 See Fig. 18, 19, 20

B1 1706 4

1707

X6

X6

B1

2846

5

1719 430 1702 X6

6

1703 1717

1704

7

1705 8

Fig. 17 ADF (1/4)

249 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P Safety Mark

Ref. No. 1801 1802 1803 1804 1805 1806 1807 1808 1809 1810 1811 1812 1813 1814 1815 1816 1817 1818 1819 1820 1821 1822

Part Number DZJA000858 DZJA000853 DZKG000152 DZJM000679 DZKN000270 DZJM000680 DZJM000690 DZKN000269 DZJM000681 DZKN000268 DZJM000677 DZLA000258 DZLM000072 DZJM000692 DZJA000850 DZJA000855 DZKG000154 DZJM000684 DZJM000688 DZKN000273 DZJA000856 PJZEF21200PU

1823 DZQJ000022

Part Name Plate, Angle Bracket, Left Hinge Shaft, Left Hinge Base, Left Hinge Spring, Lower Left Hinge Guide, Left Spring Holder, Left Spring Spring, Upper Left Hinge Holder, Upper Left Spring Spring, White Front Holder, Stamp Roller, Exit 1 Bushing, P6L8 Sheet, White Guide, White Bracket, Hinge Right Shaft, Hinge Right Base, Hinge Right Guide, Spring Right Spring, Hinge Right Plate, Hinge Right Scanning Pad Hook and Loop Fastener Tape (Loop Side)

New Remarks Destination Parts C All C All C All C All C All C All C All C All C All C All For DP-8020E/8020P* All C C All C All C All C All C All C All C All C All C All C All C All C

All For DP-8020E/8020P* All

1824 L9AAAABA0002

Solenoid, Stamp

C

1825 DZJM000926 1826 DZJM000927 DZHT000027 1827 DZHT000004 1828 DZJM001358 DZHP000237 1829 DZHP000240 1830 DZHP005513 1704 DZKN000271 1717 DZJM001241 2125 DZHP001664

Film, Lower Film, Upper

C C

Stamp Head

C

Sheet, Protection

C

Assembly, Stamp

C

For DP-8020E/8020P*

Unit, Stamp Spring, White Rear Spacer Base, Stamp

C C C C

For DP-8020E/8020P*

2852 DZFP001967

Harness, Stamp

C

For DP-8020E/8020P* All

Screw Screw E-Ring Screw Screw, Silver

C C C C C

All All All All All

X6 1N J7 6A B1

XTB3+8JFJ XTB4+8JFJ XUC4VM XTB3+12GFJ DZPB000007

For DP-8020E/8020P*

For DP-8020E/8020P*

All All AUR Other All AUR Other All All All All

250 Ver. 1.0

OCT 2006

A

B

C

DP-8020E/8020P/8016P E

D

1816 1817 1

J7

B1 1801 1N

1818 1819 1820

6A

1717

1704

2

1821

3

1826

4

1828 1810

1815

1827 1826

1825

1829

2125

1814 1830

5

1823 2852 1824 1802

X6

1803

1812

6

1811 1813

1809 B1

J7 1801

X6 1808 1N 1807

7

1806 6A 1804

1805

1822 8

Fig. 18 ADF (2/4)

251 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P Safety Mark

Ref. No. 1901 1902 1903 1904

Part Number

Part Name

DZJA000854 DZMA003295 FFPLK0381B DZKN000267

Bracket, Adjust Cover, ADF Latch Spring, Latch

New Parts C C C C

Remarks

Destination All All All All

1905 L6HBHHGC0011

Motor, ADF

C

All

1906 1907 1908 1909 1910 1911 1912 1913 1914 1915 1916 1918 1919 429 698 2848 2850 18 X6 H7

Bracket, Motor F Gear, E20S20 F Gear, E28S22 F Gear, E16 Pulley, S27 Belt, Drive 1 Belt, Drive 2 Bracket, Pulley Bracket, Right Clamp Cover, ADF PC Board Switch, Cover Open Spring, Ground Clamp Bushing Harness, ADF Motor Harness, Open Switch Screw Screw Snap Ring

C C C C C C C C C C C C C C C C C C C C

All All All All All All All All All All All All All All All All All All All All

Snap Ring

C

All

S9

DZJA000849 DZLF000453 DZLF000454 DZLF000315 DZLF000452 DZLK000029 DZLK000023 DZJA000851 DZJA000848 DZJK000018 DZJA001190 DZCF000022 DZKQ000073 DZJK000045 FFPMQ0649 DZFP001964 DZFP001966 XYN3+F6FJ XTB3+8JFJ FFPFJ0041B FFPFJ0033B DZJM000171

or

252 Ver. 1.0

OCT 2006

A

B

C

X6

429

1905 2848

DP-8020E/8020P/8016P E

D

X6

429

1

1916

1906

1910 698

18

X6

2

1919

X6

1907

X6

1915

1912

1908 X6 429

18

3

H7 1909

1911

S9

X6 1910

1913

1918

X6

2850 698

1914

X6

4

1902 5

6

1904 1903

7

See Fig. 20

1901 X6 8

Fig. 19 ADF (3/4)

253 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P Safety Mark

Ref. No. 2001 2002 2003 2004 2005 2006

Part Number

Part Name

DZLA000216 DZJM000672 DZKQ000070 DZJM000674 DZJM000013 DZKR000004

Roller, Paper Feed Guide, Lower Paper Feed Spring, Timing Actuator, Timing Plate, Pressure Spring, Pressure Plate Lever, Pressure Adjustment Actuator, NP Spring, NP Actuator Roller, Feed Plate, Exit Roller, Exit Pinch Stopper, ADF Cover Shaft, Drive Pinch Roller, Drive Pinch Stopper, Original Guide, Upper Paper Feed Roller, Pre Feed Shaft, Pre Feed Gear 2, Pre Feed Gear 1, Pre Feed Spring, Pick Up Cover, Pad Rubber, Separation D Gear, D26 Holder, Roller Rack, Pickup Guide, Rack Paper Feed Shaft Assembly F Gear, D16 Spring, Pinch Roller Pressure Sheet, ADF Bracket, Center Plate, Exit Sensor, Photo Bushing Bracket, Adjustment Cover, ADF Latch Spring, Latch

2007 DZJM000678 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 2018 2019 2020 2021 2022 2023 2024 2025 2026 2027 2028 2029 2030

DZJM000675 DZKQ000074 DZLA000257 DZKP000251 DZLA000326 DZJM000683 DZKG000150 DZLA000304 DZJM000686 DZJM000673 DZLA000204 DZKG000151 DZJM000414 DZLF000330 DZKN000272 DZJM000682 DZJN000052 DZLF000456 DZJM000685 DZJM000691 DZJM000687 DZKG000153 DZLF000385

2031 DZKR000037 2032 2033 2034 131 698 1901 1902 1903 1904

DZKM000020 DZJA001172 PJBUC0091Z DZAL000211 FFPMQ0649 DZJA000854 DZMA003295 FFPLK0381B DZKN000267

2324 L9EAAJ000020 2848 2849 X6 H7 S9

DZFP001964 DZFP001965 XTB3+8JFJ FFPFJ0041B FFPFJ0033B DZJM000171

or

New Parts C PM C C C C C

Remarks

Destination All All All All All All

C

All

C C C C C C C C C C C C C C C C C C C C C C C

All All All All All All All All All All All All All All All All All All All All All All All

PM

PM

C

All

C C C C C C C C C

All All All All All All All All All

Clutch

C

All

Harness, ADF Motor Harness, PNT/REV Screw Snap Ring

C C C C

All All All All

Snap Ring

C

All

254 Ver. 1.0

OCT 2006

A

B

C

DP-8020E/8020P/8016P E

D

2848 698

H7

1902 1

2324

2029

2028 X6

2017 2

2027

2016

2018

2026

2030

2019 3

2020 1903

2021 2031

1904

2015

2022

698

2032 H7

X6

2012

4

2014 2011

2001

2034

2025

2012

2023

2013

2011 5

2024

2002

2849 6

1901 2003

X6

131 2005 2009 2004

2849

7

2010 698 S9

2006 2033 2007

131

2008

X6 8

Fig. 20 ADF (4/4)

255 Ver. 1.0

OCT 2006

5.16. Inverting Automatic Document Feeder (For DP-8020E) Safety Mark

Ref. No.

Part Number

Part Name

New Parts

DP-8020E/8020P/8016P

Remarks

Destination

2101 DZMA002337

Cover, ADF Rear

C

All

2102 DZJA001470 2103 DZJA001472 2104 DZKG000424 2105 DZJA001473

C C C C

All All All All

C

All

C

All

2108 DZJM000486 2109 DZKN000207

Hinge, Arm Plate, Reinforcement Shaft, P6 Base, Right Hinge (B) Guide, White Reference Seal Spring, White Reference Seal Guide Seal, White Reference Coil Spring, Ground

C C

All All

2110 DZMA002333

Base, ADF

C

All

C

All

C C C C C C C C C C C C C C C C C C C C

All All All All All All All All All All All All All All All All All All All All

2106 DZJA000689 2107 DZKN000187

2111 DZKP000215 2112 2113 2114 2115 2116 2117 2118 2119 2120 2121 2122 2123 2124 2125 2126 2127 2128 2129 2130 2131

PJUIC0254Z DZMC000713 DZJA000726 DZJM000449 DZJC000392 DZJP000026 DZJC000391 DZJM000469 DZJA000696 DZJM000475 DZLM000007 DZJM000888 DZJJ000009 DZHP001664 DZMA002329 DZJM001285 DZKP000358 DZJM000429 DZLA000080 DZMA004372

Plate Spring, ADF Input Tray Bracket, ADF Mounting Cover, Hinge Stopper, Hinge Film, Hinge Carrier, Sleeve Felt Holder, Sleeve Sleeve, Right Bracket, Sensor Slider Bushing, P6L7.4 Film, Front Band Base, Stamp Cover, ADF Film, Top Cover Spring, Plate Holder, Stamp Roller 1, Pinch Cover 2, Hinge

For DP-8020E/8020P*

256 Ver. 1.0

OCT 2006

A

B

C

X6

131

429

2101

DP-8020E/8020P/8016P E

D

2857 2860

B1

2120

1

X6 X6 2847

See Fig. 26 2124

2

B4

See Fig. 27

See Fig. 22

X6 2111

3

2117

2122

2121 2126

B4

2104 X6

2115

2119

2118 2122

J7

4

2123

X6

2121 2117

X6

2102

2103 X6

X6 M2

J7

2114

5

2116 F7 2131

X6 2128

2110

2105

2113

6

2130

6A 2112

2106

2107

1829 7

1827 2125 X6 X6

1824 2107 2108

2129 2127

8

Fig. 21 Inverting ADF (1/7)

2109

257 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P Safety Mark

Ref. No. 131 429

Part Number DZAL000211 DZJK000045

1824 L9AAAABA0002 DZHT000027 DZHT000004 DZHP000237 1829 DZHP000240 1827

2847 DZEC101648R 2857 2860 X6 J7 6A B1 B4 F7 M2

DZFP001674 DZFP001714 XTB3+8JFJ XUC4VM XTB3+12GFJ DZPB000007 XTB3+8JFI XSN4+W10FN DZPA000064

Part Name Sensor, Photo Clamp

New Parts C C

Remarks

Destination All All

Solenoid, Stamp

C

For DP-8020E/8020P*

Stamp Head

C

For DP-8020E/8020P*

Assembly, Stamp

C

For DP-8020E/8020P*

PC Board, ADF

C

Harness, B1 Sensor Harness, ADF-FG Screw E-Ring Screw Screw, Silver Screw Screw Screw, Thumb

C C C C C C C C C

For DP-8020E (RTL/PbF) For DP-8020E

All AUR Other AUR Other All All All All All All All All All All

258 Ver. 1.0

OCT 2006

A

B

C

X6

131

429

2101

DP-8020E/8020P/8016P E

D

2857 2860

B1

2120

1

X6 X6 2847

See Fig. 26 2124

2

B4

See Fig. 27

See Fig. 22

X6 2111

3

2117

2122

2121 2126

B4

2104 X6

2115

2119

2118 2122

J7

4

2123

X6

2121 2117

X6

2102

2103 X6

X6 M2

J7

2114

5

2116 F7 2131

X6 2128

2110

2105

2113

6

2130

6A 2112

2106

2107

1829 7

1827 2125 X6 X6

1824 2107 2108

2129 2127

8

Fig. 21 Inverting ADF (1/7)

2109

259 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P Safety Mark

Ref. No.

Part Number

Part Name

Remarks

Destination

Tray, ADF Input

C

Guide, Original Rear Guide, Original Front Spring, Actuator Base, Actuator Bracket, Actuator Rack, Original Guide Cover, ADF Tray Bottom Tray, Sub

C C C C C C C C

PU,PUG Other All All All All All All All All

Cover, ADF Front

C

All

Assembly, ADF Tray

C

104 131 1709 DZHC000057 1710 DZLF000077

Pad, Scanning Sensor, Photo Actuator, Original Length F Gear, D14

C C C C

PU,PUG Except PU, PUG All All All All

2110 DZMA002333

Base, ADF

C

All

C

All

2201 2202 2203 2204 2205 2206 2207 2208 2209

DZMA002341 DZMA002474 DZMA004339 DZMA004338 DZKQ000012 DZJM000159 DZJA000699 DZMA002348 DZMA002343 DZML000508

New Parts

2210 DZMA002335 2211

DZHP010765R DZHP010766R PJHEC0124Z DZAL000211

2111 DZKP000215 2832 2856 X6 B1 E8 S9

DZEC102304R DZFP001711 XTB3+8JFJ DZPB000007 XTW3+10SFJ FFPFJ0033B DZJM000171

or

Plate Spring, ADF Input Tray PC Board, SNS Harness, SNS Screw Screw, Silver Screw

C C C C C

Snap Ring

C

For DP-8020E

All All All All All All

260 Ver. 1.0

OCT 2006

A

B

C

DP-8020E/8020P/8016P E

D

2201

2202

2203 1

2211

2856 2856

E8

131

2207

2856

2204 1709

2832

X6

2

2205

1710

E8

2207

3

2206 E8

2111

E8 S9 See Fig. 23 4

E8 2208

5

See Fig. 24, 25 See Fig. 24

2209 6

B1

7

2210

2110 104

8

Fig. 22 Inverting ADF (2/7)

261 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P Safety Mark

Ref. No. 2301 2302 2303 2304 2305 2306 2307 2308 2309 2310 2311 2312 2313 2314 2315 2316 2317 2318 2319

Part Number DZKG000422 DZKG000423 DZJM000434 DZJM000435 DZJA000694 DZJA000693 DZLF000382 DZLF000036 DZLF000028 DZKG000109 DZJM000411 DZJM000410 DZJM000408 DZLA000205 DZLF000329 DZKG000107 DZKN000209 DZKN000231 DZKQ000042

2320 DZKN000422

Part Name Shaft, P8L Shaft, P8S Holder, Spring T Holder, Spring B Plate, Reinforcement B Plate, Reinforcement A Gear, E18 Gear, E25 Gear, E14E25 Shaft, ADF Guide, Rear ADF Guide, Front ADF Holder, ADF Roller, ADF Gear, ADF Shaft, Pre Feed Roller Spring, Latch Spring, Hinge Support Spring, Introduction Spring, Hinge (Silver, i-ADF) Bushing Base, Left Hinge (A)

New Parts C C C C C C C C C C C C C C PM C C C C C

Remarks

Destination All All All All All All All All All All All All All All All All All All All

C

All All All All

2321 DZJL000115 2322 DZJA001471 2323 DZMG000018

Latch

C C C

2324 L9EAAJ000020

Clutch

C

All

2325 L9EAAJ000022

Clutch

C

All

2326 DZPK000017 2327 DZPG000001

Washer Pin

C C

All All

262 Ver. 1.0

OCT 2006

A

B

C

J7

Y9

2115

2301

2102

2113

1

X6

X6

2326 2104 2122 M2

2114

5Z

J7

2

2320 2318

2305

2122 2322

2859

X6 2302

131

2306

S9

6A 2112

X6

2103

2304

2303

5Z

DP-8020E/8020P/8016P E

D

2317

2321 2307

3

2323

2853

S9 2308

See Fig. 24, 25

4

2325

2309 5

2853

S9

2321 2310

H7

2324

6

2321

2311

2319 2313

2316 2018

S9

7

2020

2314 S9

2327

H7 2030

2315 2312

2021 8

Fig. 23 Inverting ADF (3/7)

263 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P Safety Mark

Ref. No. 131 2018 2020 2021 2030 2102 2103 2104 2112 2113 2114 2115 2122

Part Number

Part Name

DZAL000211

Sensor, Photo Roller, Pre Feed Gear 2, Pre Feed Gear 1, Pre Feed F Gear, D16 Hinge, Arm Plate, Reinforcement Shaft, P6 Bracket, ADF Mounting Cover, Hinge Stopper, Hinge Film, Hinge Bushing, P6L7.4 Harness, ADF Motor and Clutch Harness, Exit Sensor Screw Screw E-Ring E-Ring Screw Snap Ring Screw, Thumb

DZLA000204 DZJM000414 DZLF000330 DZLF000385 DZJA001470 DZJA001472 DZKG000424 PJUIC0254Z DZMC000713 DZJA000726 DZJM000449 DZLM000007

2853 DZFP001705 2859 X6 Y9 J7 5Z 6A H7 M2 S9

DZFP001713 XTB3+8JFJ XYN4+F8FJ XUC4VM XUC6VM XTB3+12GFJ FFPFJ0041B DZPA000064 FFPFJ0033B DZJM000171

or

Snap Ring

New Parts C C PM C C C C C C C C C C C

Remarks

Destination All All All All All All All All All All All All All

C

For DP-8020E

All

C C C C C C C C

For DP-8020E

All All All All All All All All

C

All

264 Ver. 1.0

OCT 2006

A

B

C

J7

Y9

2115

2301

2102

2113

1

X6

X6

2326 2104 2122 M2

2114

5Z

J7

2

2320 2318

2305

2122 2322

2859

X6 2302

131

2306

S9

6A 2112

X6

2103

2304

2303

5Z

DP-8020E/8020P/8016P E

D

2317

2321 2307

3

2323

2853

S9 2308

See Fig. 24, 25

4

2325

2309 5

2853

S9

2321 2310

H7

2324

6

2321

2311

2319 2313

2316 2018

S9

7

2020

2314 S9

2327

H7 2030

2315 2312

2021 8

Fig. 23 Inverting ADF (3/7)

265 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P Safety Mark

Ref. Part Number No. 2401 DZJA001460 2402 DZJA000679

Bracket, Front ADF Bracket, Solenoid

2403 L9AAAEGB0006

Solenoid

C

All

2404 2405 2406 2407 2408 2409 2410

Lever, Release Cover, Gear Bracket Gear, B44 Coil Spring, Idle Gear Plate, Moving Gear Bracket, Moving Gear Gear, B42E27

C C C C C C C

All All All All All All All

2411 L9AABCEZ0001

Solenoid

C

All

2412 DZKN000185

Spring, Reversing Guide 1 Bracket, Reversing Guide 1 Adjuster Joint Bracket, Reversing Guide 2 Spring Connector 3 Gear, B18 Lever, Stopper Stopper, Rubber Bushing, P6 Gear, E18 Drive Holder, Pinch Roller Plate Spring, Ground Bracket, Inverting Guide Front Bracket, Inverting Guide Rear Roller, Inverting Feed Cover, ADF Exit Guide, Inverting 2 Guide, Duplex 2 Guide, Inverting 1 Spring, Duplex 2 Guide Lever, Duplex 2 Guide Connector, TR2 Brush, Antistatic Roller 1, Pinch Spring, Latch Bushing Latch Harness, CLT Screw Screw Snap Ring

C

All

C

All

C C

All All

C

All

C C C C C C C C C

All All All All All All All All All

C

All

C

All

C C C C C C C C C C C C C C C C C

All All All All All All All All All All All All All All All All All

Snap Ring

C

Part Name

DZJM000412 DZJM000432 DZLF000015 DZKN000006 DZJM000431 DZJA000697 DZLF000172

2413 DZJA000685 2414 DZJM000422 2415 DZJM000421 2416 DZJA001462 2417 2418 2419 2420 2421 2422 2423 2424 2425

DZKN000188 DZFC001576 DZLF000327 DZJM000430 DZJM000477 DZLM000046 DZLF000332 DZKP000205 DZKP000206

2426 DZJA001466 2427 DZJA001467 2428 2429 2430 2431 2432 2433 2434 2435 1719 2130 2317 2321 2323 2855 X6 5M H7 S9

DZLA000383 DZMA002339 DZJM000424 DZJM000425 DZJM000423 DZKN000186 DZJM000426 DZFC001575 DZGT000007 DZLA000080 DZKN000209 DZJL000115 DZMG000018 DZFP001710 XTB3+8JFJ XYN3+F4FJ FFPFJ0041B FFPFJ0033B DZJM000171

or

New Parts C C

Remarks

Destination All All

For DP-8020E

All

266 Ver. 1.0

OCT 2006

A

2423

B

H7

C

DP-8020E/8020P/8016P E

D

2321 2429

X6

1

2428 1719

2427 2

2130 2321 H7 2424 2425 3

2431 2430

2422

2426

2432

2433 4

2434 X6 X6

2402

2404

2403 5

2401

5M 2435

2422

2420

2405 2855

2317

2409 2408

2323 2321

X6

2419

2406 2410

6

2421

2417

2407

S9 2415 2403

X6

2412

X6 2414 2416

2413

7

2418

5M

2435

2855

2411 5M

2855

8

Fig. 24 Inverting ADF (4/7)

267 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P Safety Mark

Ref. Part Number No. 2501 DZJA001459 2502 DZJF000407

Part Name Bracket, Rear ADF Guide, Upper ADF Plate Spring, Pinch Roller Plate, Release Lever Guide, Lower ADF Stopper, Original Shaft, Separation Roller Bushing Roller, Separation Bushing, Torque Limiter Spring, Torque Limiter Spring, Separation Roller Holder, Separation Roller Film, ADF Pre Feed Roller, Exit 3 Guide 1, Reversing Roller, Feed 2 Guide, Feed 2 Roller Holder, Sensor C Actuator, Sensor C Holder, Sensor B2 Actuator, Sensor B2 Film, Reversing Guide 1 Spring, Sensor B2 Assembly, Torque Limiter Sensor, Photo Clamp Brush, Antistatic Sheet, ADF Film, F Band Roller 1, Pinch Plate, Reinforcement B Gear, E18 Bushing

2503 DZKP000202 2504 DZJA001461 2505 2506 2507 2508 2509 2510 2511 2512 2513 2514 2515 2516 2517 2518 2519 2520 2521 2522 2523 2524 2525 131 430 1719 2032 2123 2124 2130 2305 2307 2321

DZJF000408 DZJM000409 DZKG000416 DZJM000415 DZLA000206 DZJM000416 DZKQ000031 DZKN000184 DZJM000413 DZJM000442 DZLA000382 DZJM000420 DZLA000381 DZJM000418 DZJM000419 DZHC000105 DZJA000684 DZHC000104 DZJM000491 DZKR000024 DZHP003955 DZAL000211

DZJK000046 DZGT000007 DZKM000020 DZJM000888 DZJJ000009 DZLA000080 DZJA000694 DZLF000382 DZJL000115 2325 L9EAAJ000022 2401 DZJA001460 2404 DZJM000412 2420 DZJM000430 2422 DZLM000046 2858 DZFP001712 2859 DZFP001713 X6 XTB3+8JFJ FFPFJ0033B S9 DZJM000171

or

New Parts C C

Remarks

Destination All All

C

All

C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C

All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All

PM PM PM

Clutch

C

All

Bracket, Front ADF Lever, Release Lever, Stopper Bush, P6 Harness, Read Point Sensor Harness, Exit Sensor Screw

C C C C

All All All All

Snap Ring

C

C

For DP-8020E

All

C C

For DP-8020E

All All All

268 Ver. 1.0

OCT 2006

A

B

C

DP-8020E/8020P/8016P E

D

X6 2032 2502

X6

1

430 2305 2307

2321

X6 2

2124

S9

2130

2325

2503

430 131 3

2501

2858

1719

S9 2505

2504 2321

2507 2321

4

2525 2515 2508 2512

2523

2516

2506

2511 2510

S9

S9

2509 X6

2514

2513 5

2404 2401 2517

X6 2422 S9

X6

6

S9

2321 2521

2420

2321

2859 2123 2518

X6

7

131 2519

2524 2859 2522

X6

131

8

Fig. 25 Inverting ADF (5/7)

2520

269 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P Safety Mark

Ref. No.

Part Number

Part Name

New Parts

Remarks

Destination

2601 L6HBJJGB0001

Motor, ADF

C

All

2602 2603 2604 2605 2606 2607 2608 2609 2610 2611 2612 2613 2614 2615 2616 2617 2619 2620 2621 2622 2623 2624 2625 2626 2627 2628

Bracket, Gear Shaft Gear, E26S35 Drive Gear, E29 Gear, E21E27 Gear, D24E18 Gear, D16 Gear, D24E18 Bracket, Motor Pulley Belt 2, Timing Bracket, Pulley Shaft 1, Drive Shaft 2, Drive Gear, E21 Drive Bracket, Actuator Spring, Gear Bracket, Rear ADF Cover Bracket, Front ADF Cover Actuator 2 Shaft, Pinch Roller Roller 2, Pinch Plate Spring 2, Discharge Plate 1, Adjustment Actuator 3 Cover, Sub ADF Plate Spring, Pinch Roller Sponge Spring, B1 Sensor Clutch Sensor, Photo Clamp Clamp Cover, ADF Gear, E25 Bushing Latch Gear, E18 Drive Harness, ADF Motor and Clutch Harness, ADF Clutch Harness, B1 Sensor Screw Screw

C C C C C C C C C C C C C C C C C C C C C C C C C C

All All All All All All All All All All All All All All All All All All All All All All All All All All

C

All

C C C C C C C C C C C

All All All All All All All All All All All

Snap Ring

C

DZJA000695 DZKG000113 DZLF000331 DZLF000283 DZLF000333 DZLF000335 DZLF000008 DZLF000191 DZJA001468 DZLB000013 DZLK000013 DZJA001469 DZKG000114 DZKG000115 DZLF000334 DZJA000675 DZKN000126 DZJA000681 DZJA000680 DZHC000102 DZKG000108 DZLA000211 DZKP000204 DZJA000677 DZHC000103 DZJM000407

2629 DZKP000200 2630 2631 2632 131 429 430 2126 2308 2321 2323 2423

DZJM000476 DZKQ000051 L9EAAJ000021 DZAL000211 DZJK000045 DZJK000046 DZMA002329 DZLF000036 DZJL000115 DZMG000018 DZLF000332

2853 DZFP001705 2854 2857 X6 Y9 S9

DZFP001672 DZFP001674 XTB3+8JFJ XYN4+F8FJ FFPFJ0033B DZJM000171

or

C

For DP-8020E

All

C C C C

For DP-8020E For DP-8020E

All All All All All

270 Ver. 1.0

OCT 2006

A

B

C

DP-8020E/8020P/8016P E

D

2601 X6

S9

2602 1

2308

2321 429

2603

2853

S9

2854

429

2604 2610 430 2605

2321

2

2632

Y9

2606

2608

2607

S9

2321 2614 S9

2612

2615

2609

3

2126 2604 2605

2321 2423

2616

2321

4

S9 X6

2308 S9 2611

2619

2620

2623

2613 5

2617

2323 2624

X6 2622 2619

2630 2323

6

2621

X6

2629 X6 2857 131 X6

7

2627 2631 2628 X6

2625 2626 8

Fig. 26 Inverting ADF (6/7)

271 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P Safety Mark

Ref. No. 2701 2702 2703 2704 2705 2706 2707 2708 2709 2710 2711 2712 2713 2714 2321 2423 2624 X6

Part Number DZJM000427 DZJA000688 DZKG000112 DZKP000207 DZJF000409 DZLA000384 DZJM001230 DZKP000203 DZJA000678 DZKP000201 DZJM000406 DZKG000110 DZJM001284 DZJM001283 DZJL000115 DZLF000332 DZLA000211 XTB3+8JFJ

Part Name Guide, Upper Feed Guide, Skew Shaft, Drive Pinch Plate Spring, Drive Guide, Sub Top Roller, Drive Guide, Lower Feed Plate Spring, Discharge Plate, Adjustment 2 Plate Spring, Pinch 1 Guide, Inverting Feed Shaft, Pinch 2 Guide, Film A Sheet, Guide 2 Bushing Gear, E18 Drive Roller 2, Pinch Screw

New Parts C C C C C C C C C C C C C C C C C C

Remarks

Destination All All All All All All All All All All All All All All All All All All

272 Ver. 1.0

OCT 2006

A

B

C

2423

DP-8020E/8020P/8016P E

D

2321

1

2706 X6 2

2321 2707

2710

2423

3

2708

2712

2709

X6

4

2711 2624 X6 2701 2713

5

2703

2624

2714 6

2704 2624 2702

7

2705 8

Fig. 27 Inverting ADF (7/7)

273 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

5.17. PC Boards/Harnesses Safety Mark

Ref. No.

2801

Part Number DZEC104116 DZEC104134 DZEC104119 DZEC104125 DZEC104137 DZEC104122 DZEC104131 DZEC104128 DZEC104140 DZEC104117 DZEC104135 DZEC104120 DZEC104126 DZEC104138 DZEC104123 DZEC104132 DZEC104129 DZEC104141 DZEC104118 DZEC104136 DZEC104121 DZEC104127 DZEC104139 DZEC104124 DZEC104133 DZEC104130 DZEC104142 DZEC104147 DZEC102176R PJWPF2740AZ

2802 2803 2804 2806 DZEC102751R 2810 2811 2812 2813

Part Name

Remarks

For DP-8016P (RTL/PbF)

PC Board, SC

N

For DP-8020P* (RTL/PbF)

For DP-8020E (RTL/PbF)

PC PC PC PC

Board, Board, Board, Board,

SPC DC RLB WTS

N C C C

DZFP001634 DZFP001635 DZFP001636 DZFP001622 DZFP001632 DZFP001651

Harness, PNL1

C

Harness, CCD Harness, DC Harness, HDD

C C C

DZFP001623

Harness, LSU 2

DZFP002105

Harness, LSU 2B

DZFP001587 DZFP001620 DZFP001598 DZFP001589 DZFP001595

Harness, Harness, Harness, Harness, Harness,

2814

2815 2816 2817 2818 2819

New Parts

C

PS SC-SPC SNS Thermistor 2 WTS

C C C C C

RTL/PbF RTL/PbF

For DP-8020E For DP-8020P* For DP-8016P

Destination PU, PUG PA PB, PY PF PK PM PP PS PT PU, PUG PA PB, PY PF PK PM PP PS PT PU, PUG PA PB, PY PF PK PM PP PS PT All All All All All All All All All All PU, PT, PK, PUG Except PU, PT, PK, PUG All All All All All

274 Ver. 1.0

OCT 2006

A

B

2810

C

DP-8020E/8020P/8016P E

D

2811 SC (2801) ADF (2846)

CN52

2848

CN55

2827

CN22

1

2849

CN21 CN30

CN25

CN29 CN27

CN28

2

2852 CN53

2851

2849

2816

CN145

2812

2850

i-ADF (2847)

CN59 CN51 CN66

CN30

CN57

2813

2815

2827

2859

3

CN27 CN29

2843 2814

CN28 CN24

SPC (2802)

CN656

2828

2827

2861 2815 2816

4

CN22

2853

2856

2855

CN657 CN721

2818

CN720

2819

CN655

CN726

CN703

CN717

CN709

2820

CN723

2818

CN712

2821

CN715

2821

CN722

CN142

CN141

CN143

6

2842

2822

RLB (2804)

2820 2831

CN706

CN173

CN702 CN708

CN172

2830 2825

2812 5

CN701 CN707

DC (2803)

2812

CN719

CN650

CN727

2826

2857

CN26

2817

2829

2858

CN21

2854

3138

2815

CN171

2833

7

2823

8

Fig. 28 PC Boards/Harnesses (1/2)

275 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P Safety Mark

Ref. No.

Part Number

DZFP001592 DZFP001603 DZFP001588 DZFP001611

Harness, Sensor Harness, Harness, Harness, Harness,

DZFP001596

Harness, LSU 1

DZFP002104

Harness, LSU 1B

DZFP001969

Harness, ADF

2820 DZFP001597 2821 2822 2823 2825

Part Name Paper Tray SSN BSMT ILS Paper Tray 2

2826

DZFP001377 DZFP001593 DZFP001594 DZFP001639 DZFP001641 DZFP001653 DZFP001633 DZFP001624 DZEC102303R

2847 DZEC101648R 2848 2849 2850 2851

DZFP001964 DZFP001965 DZFP001966 DZFP001968

2852 DZFP001967

All

C C C C

All All All All PU, PT, PK, PUG Except PU, PT, PK, PUG All PK, PT, PU, PUG Other

C

Harness, i-ADF

C C C C C C C C

PC Board, ADF

C

Harness, Harness, Harness, Harness,

C C C C

All All All All

C

For DP-8020E/8020P* All

C

For DP-8020E

All

ADF Clutch CLT SNS B1 Sensor Read Point

C C C C

For For For For

DP-8020E DP-8020E DP-8020E DP-8020E

All All All All

C

For DP-8020E

All

For DP-8020E

All All

ADF Motor PNT/REV Open Switch ADF SNS

Harness, Stamp

Exit Sensor KEY

C C

3138 PJWQF2120PB

Assembly, Lift Motor

C

2858 DZFP001712

For DP-8020E

Harness, SCN Harness, INV Harness, PTC-AC 1 Harness, PTC-AC 3 Harness, RLB Harness, HDDPS Harness, CSS PC Board, ADF

2859 DZFP001713 2861 DZFP001902

DZFP001672 DZFP001710 DZFP001711 DZFP001674

Destination

C

Harness, Clutch Harness, Harness, Harness, Harness, Harness, Sensor Harness, Harness,

2853 DZFP001705 2854 2855 2856 2857

Remarks

C

2827 DZFP001971

2828 2829 2830 2831 2833 2842 2843 2846

New Parts

ADF Motor and

RTL/PbF For DP-8020E (RTL/PbF)

All All All All All All All All All

All

276 Ver. 1.0

OCT 2006

A

B

2810

C

DP-8020E/8020P/8016P E

D

2811 SC (2801) ADF (2846)

CN52

2848

CN55

2827

CN22

1

2849

CN21 CN30

CN25

CN29 CN27

CN28

2

2852 CN53

2851

2849

2816

CN145

2812

2850

i-ADF (2847)

CN59 CN51 CN66

CN30

CN57

2813

2815

2827

2859

3

CN27 CN29

2843 2814

CN28 CN24

SPC (2802)

CN656

2828

2827

2861 2815 2816

4

CN22

2853

2856

2855

CN657 CN721

2818

CN720

2819

CN655

CN726

CN703

CN717

CN709

2820

CN723

2818

CN712

2821

CN715

2821

CN722

CN142

CN141

CN143

6

2842

2822

RLB (2804)

2820 2831

CN706

CN173

CN702 CN708

CN172

2830 2825

2812 5

CN701 CN707

DC (2803)

2812

CN719

CN650

CN727

2826

2857

CN26

2817

2829

2858

CN21

2854

3138

2815

CN171

2833

7

2823

8

Fig. 28 PC Boards/Harnesses (1/2)

277 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P Safety Mark

Ref. No.

2901

Part Number ETXDN478AAEA ETXDN478EAEC

Part Name

PC Board, PS

ETXDN478EAEA

New Parts C N

Remarks

C

DZEC103793

DZEC103795

2902

PC Board, MJR

C

RTL/PbF

PC Board, FXB

C

RTL/PbF

PC PC PC PC

C C C C

RTL/PbF

DZEC103797

DZEC103116R DZEC103117R 2904 DZEC102911R 2906 DZEC102913R 2908 DZEC103665 2909 DZEC102749R DZEC102917R 2910 DZEC103157R 2911 DZFP001617 2912 DZFP001602 2913 DZFP001599 2914 DZFP001600 2915 DZFP001630 2916 DZFP001627 2917 DZFP001628 2918 DZFP001629 2903

2919 DZFP001614 2920 2921 2922 2923 2924 2925 519

DZFP001613 DZFP001612 DZFP001615 DZFP001533 DZFP001534 DZFP001601 MGG03204Z03

DZFP001634 2810 DZFP001635 DZFP001636 2815 DZFP001587 2825 DZFP001611 2833 DZFP001653

Board, Board, Board, Board,

PNL1 PNL3 CST2 CST3

Destination PU, PUG, PT PK Except PU, PUG, PT, PK AUR AAR, ABR, AGR AHR, AJR, ALR AMR, APR, ARR AVR, EER, ENR YGR, YPR, YXR Except AAR, ABR, AGR AHR, AJR, ALR AMR, APR, ARR AUR, AVR, EER ENR, YGR, YPR YXR AUR Except AUR

PC Board, SSN

C

Harness, HV 2 Harness, HV 1 Harness, ACIN Harness, ACSW Harness, MJR-FXB Harness, PNL1-PNL3 A Harness, PNL1-PNL3 B Harness, PNL1-PNL4 Harness, Paper Tray Sensor 2 Harness, CL2 Harness, Paper Tray 3 Harness, CL3 Harness, PNL2 1 Harness, PNL2 2 Harness, HT LCD Module

C C C C C C C C

All All All All Except PK, PT PK, PT All All All All All All All All

C

All

C C C C C C C

Harness, PNL1

C

Harness, PS Harness, Paper Tray 2 Harness, RLB

C C C

All All All All All All All All All All All All All

RTL/PbF RTL/PbF

For DP-8020E For DP-8020P* For DP-8016P

278 Ver. 1.0

OCT 2006

A

B

C

DP-8020E/8020P/8016P E

D

PS (2901) 2911

MJR (2902)

2912 1 CN502 CN504

2912

2915 CN25

CN501

2815 CN500

2

2915 CN11

2815

CN12 CN22 CN10

2815 CN1 CN5 CN2

2815

PNL1 (2904) 2810

2913 2833

CN220

2916

CN3

3

519 CN223

2918 CN234

CN230

CN232

2914

2923

CN231

CN233

2917

4

2924

2925 CST2 (2908) FXB (2903) 2915

2919

2825

2825

CN770

CN771

CN775

2919

5

CN776

2921

CN392

2915

CN772 CN391

CN778

2920

CN393

6

2915

2920 PNL3 (2906)

2917

CN773

CN777

2916

2921

2920

CST3 (2909)

2919

2919

2922 CN253

CN807

CN252

2922

CN800 CN803

CN802

7

CN801 CN805

2922

CN808

2825

CN806

2922 8

Fig. 29 PC Boards/Harnesses (2/2)

279 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

5.18. 2nd/4th Paper Tray Safety Mark

Ref. Part Number No. 3001 DZJE001196 3002 DZMA004431 3003 DZJD000040

Cover, Front Paper Tray Cover, Right Paper Tray Bracket, Right Post

New Parts C C C

3004 DZMA004432

Cover, Rear Paper Tray

C

All

3005 3006 3007 3008 3009 3010 3011 3012 3013 3014 3015 3016 3017 3018 3020 3021 3022 3023 3024 618 629 631 632 633 686 690 931 1619 2130 3113 3117 S6

Bracket, Rear Upper Bracket, Rear Center Bracket, Rear Lower Right Bracket, Rear Lower Left Bracket, Drive Cover Bracket, Paper Feed Base, Right Paper Tray Bracket, Paper Tray Base Bracket, Front Post Base, Left Paper Tray Cover, Jam Access Roller, Paper Tray Leg, Gum Catcher, Magnet Spring, Pinch Roller Sheet, Paper Guide Guide, Paper Bracket, Left Post Spring, Ground Bushing Roller, Reverse Arm, Reverse Bracket, Reverse Shaft, Reverse Spring, Reverse Torque Limiter 1 Plate, Base Label, Sensor Roller 1, Pinch Cover, Heater Edge Saddle Screw

C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C

All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All

Snap Ring

C

All

Screw Screw Screw

C C C

All All All

S9 X8 Y2 Y3

DZJB000436 DZJB000437 DZMB000024 DZMB000025 DZJA001400 DZJH000126 DZJB000427 DZJB000428 DZJD000042 DZJB000435 DZMB000026 DZLA000198 DZJF000489 DZMG000041 DZKP000084 DZJM001349 DZJM001322 DZJD000041 DZKP000388 DZLM000213 DZLA000366 DZKK000129 DZJA001420 DZKG000405 DZKN000416 DZHP010738 DZMC000821 PJRCC0004Z DZLA000080 DZJE001206 DZJK000017 DZPA000086 FFPFJ0033B DZJM000171 or XTB3+8GFJ XTB3+6FFJ-RP XTW3+6LFJ

Part Name

Remarks

Destination All All All

PM

PM

280 Ver. 1.0

OCT 2006

A

B

C

DP-8020E/8020P/8016P E

D

S6 See Fig. 31 1

3004 Y3 3024 3117

Y3

S6 Y3 2

3005 Y3

Y3 3117

See Fig. 31 Y3

X8 Y3

3006

3003

3008 X8

Y2 3113

3010

3009

3002 3

Y3 3003

See Fig. 31 Y3

3007

3010

Y3 4

3023

931

Y3 618 S9

3001

5

633 S9 S9

Y3

X8 686

3011

S9 631 632

X8

S9

6

629 3016

690 1619

3021

3014

Y3 X8

3018

3013

3022

3020 X8

3017 3020 X8 3016

X8

2130

X8

3017

X8 3015

7

3012

3018

8

Fig. 30 2nd/4th Paper Tray (1/2)

281 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P Safety Mark

Ref. No. 3101 3102 3103 3104 3105

Part Number DZJM001321 DZKK000123 DZKQ000106 DZLA000359 FFPMQ0536

3106 DZLF000740 3108 DZKK000128 3109 DZKQ000115 3110 DZLF000726 3111 DZLF000741 3112 DZHP009928 3113 3114 3115 3116 3117 3118 3119 3120 3121 3122 3123 3124 3125 3127 3128 3132 3133 3135 3136 3137

DZJE001206 DZJE001205 DZJK000067 DZJK000068 DZJK000017 FFPHQ0063 FFPFJ00441 DZLF000733 FFPMF10281 FFPMF1029 DZLF000734 DZJA001412 FFPMF1031B DZJH000066 DZJH000026 DZTY000357 DZJA001568 DZKN000412 DZLF000732 DZJM001076

3138 PJWQF2120PB

Part Name Guide, Paper Tray Actuator, 2nd Paper Feed Spring, Return Roller, Intermediate Bushing, 8 Metal Gear 1, OP Paper Tray Idle Arm, OP Paper Tray Connect Spring, OP Drive Gear 1, Exit Idle Gear 3, OP Paper Tray Idle Assembly, OP Paper Tray Plate Cover, Heater Holder, Heater Clamp Clamp Edge Saddle Coupling 2 Ring, Stopper Gear, Lift Up Coupling Gear 2, Lift Up Gear 3, Lift Up Gear 1, Lift Up Case B, Lift Up Gear, Worm Spacer, PCB Spacer, PCB Assembly, Lift Up Drive Case A, Lift Up Spring, Lift Up Gear, Lift Up 2 Sheet

New Parts C C C C C

Remarks

Destination All All All All All

C

All

C

All

C C

All All

C

All

C

All

C C C C C C C C C C C C C C C C C C C C

All All All All All All All All All All All All All All All All All All All All

Assembly, Lift Motor

C

All

131

DZAL000211

Sensor, Photo

C

All

424

FFPCP0034

Heater

C

All

425 603 607 611 614 616 617 619 620

DZHD000036 DZLM000006 DZKL000083 DZKK000126 DZKQ000110 DZJF000651 DZJF000668 DZLA000363 DZKG000384

Sleeve, Heater Bushing 2, P6L5 Lever, Paper Exit Sensor Latch, Arm Spring, Latch Guide, Front Guide, Feed Roller Roller, Pickup Shaft, Pickup

C C C C C C C C C

All All All All All All All All All

PM

282 Ver. 1.0

OCT 2006

A

B

C

DP-8020E/8020P/8016P E

D

694 3132

S9

3123 3122 3121 3136

3124

G6 3105

3138

3133

3125 3120 3112

3110

1

3104

3135

2

Y3 3103

3119 3111

3101

3118

3108

2919

680

131

3109

607

3106 K9

699

614

667 698

S9

627

611

665

2919

H7 668

S9 621

4

617

S9

666 Y3

619 626

698 625

616 624 622

2835

3115

3116 131

5

623 K5

3116 3127

Y2

Y3 131

620

S9

3128

3

680

688 695

2908

603

3102

424

3117 425

3113 S9 6

Y2 680 3114

680 3137 681

931 7

8

Fig. 31 2nd/4th Paper Tray (2/2)

283 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P Safety Mark

Ref. No. 621 622 623 624 625 626 627 665 666 667 668 680 681 688

DZLF000711 DZLG000035 DZLA000360 DZLF000710 DZKQ000107 DZKG000383 DZJA001402 DZJB000438 DZJM001378 DZJM001381 DZJM001388

Gear, Pickup Idler Clutch, One-way Roller, Feed Gear, Pickup Drive Spring, Pickup Shaft, Feed Bracket, Pickup Stay Feed Film, Guide Sheet, Guide Film, Guard

DZJK000004 DZJK000023 DZJA001427

Clamp Clamp Assembly, Latch Bracket

694

L9EAAK000009

Clutch, Micro 2

C

All

695

L9EAAK000010

Clutch, Micro 1

C

All

698 699 931 2835 2908

FFPMQ0649 DZJK000057 DZMC000821 DZFP001642 DZEC103665

Bushing Clamp Plate, Base Harness, PTC-AC 4 PC Board, CST2 Harness, Paper Tray Sensor 2 Snap Ring Snap Ring E-Ring Snap Ring

C C C C C

All All All All All

Part Number

2919 DZFP001614 G6 H7 K5 K9 S9 Y2 Y3

FFPFJ0039B FFPFJ0041B XUC5VM FFPFJ0043B FFPFJ0033B DZJM000171 or XTB3+6FFJ-RP XTW3+6LFJ

Part Name

New Parts C C C PM C C C C C C C C C C C

Remarks

RTL/PbF

Destination All All All All All All All All All All All All All All

C

All

C C C C

All All All All

Snap Ring

C

All

Screw Screw

C C

All All

284 Ver. 1.0

OCT 2006

A

B

C

DP-8020E/8020P/8016P E

D

694 3132

S9

3123 3122 3121 3136

3124

G6 3105

3138

3133

3125 3120 3112

3110

1

3104

3135

2

Y3 3103

3119 3111

3101

3118

3108

2919

680

131

3109

607

3106 K9

699

614

667 698

S9

627

611

665

2919

H7 668

S9 621

4

617

S9

666 Y3

619 626

698 625

616 624 622

2835

3115

3116 131

5

623 K5

3116 3127

Y2

Y3 131

620

S9

3128

3

680

688 695

2908

603

3102

424

3117 425

3113 S9 6

Y2 680 3114

680 3137 681

931 7

8

Fig. 31 2nd/4th Paper Tray (2/2)

285 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

5.19. 3rd Paper Tray Safety Mark

Ref. Part Number No. 3001 DZJE001196 3002 DZMA004431 3003 DZJD000040

Cover, Front Paper Tray Cover, Right Paper Tray Bracket, Right Post

New Parts C C C

3004 DZMA004432

Cover, Rear Paper Tray

C

All

3005 3006 3007 3008 3009 3010 3011 3012 3013 3014 3015 3016 3017 3018 3020 3021 3022 3023 3024 618 629 631 632 633 686 690 931 1619 2130 3113 3117 S6

Bracket, Rear Upper Bracket, Rear Center Bracket, Rear Lower Right Bracket, Rear Lower Left Bracket, Drive Cover Bracket, Paper Feed Base, Right Paper Tray Bracket, Paper Tray Base Bracket, Front Post Base, Left Paper Tray Cover, Jam Access Roller, Paper Tray Leg, Gum Catcher, Magnet Spring, Pinch Roller Sheet, Paper Guide Guide, Paper Bracket, Left Post Spring, Ground Bushing Roller, Reverse Arm, Reverse Bracket, Reverse Shaft, Reverse Spring, Reverse Torque Limiter 1 Plate, Base Label, Sensor Roller 1, Pinch Cover, Heater Edge Saddle Screw

C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C

All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All

Snap Ring

C

All

Screw Screw Screw

C C C

All All All

S9 X8 Y2 Y3

DZJB000436 DZJB000437 DZMB000024 DZMB000025 DZJA001400 DZJH000126 DZJB000427 DZJB000428 DZJD000042 DZJB000435 DZMB000026 DZLA000198 DZJF000489 DZMG000041 DZKP000084 DZJM001349 DZJM001322 DZJD000041 DZKP000388 DZLM000213 DZLA000366 DZKK000129 DZJA001420 DZKG000405 DZKN000416 DZHP010738 DZMC000821 PJRCC0004Z DZLA000080 DZJE001206 DZJK000017 DZPA000086 FFPFJ0033B DZJM000171 or XTB3+8GFJ XTB3+6FFJ-RP XTW3+6LFJ

Part Name

Remarks

Destination All All All

PM

PM

286 Ver. 1.0

OCT 2006

A

B

C

DP-8020E/8020P/8016P E

D

S6 See Fig. 33

3004

1

Y3 3024 Y3

3117 S6 Y3 3005

Y3

2

Y3 See Fig. 33

3117 X8 3006

Y3

3003

3008 X8 Y3 3009

Y2 3113

3010

3002

Y3

3

3003

See Fig. 33 Y3

3007

3010

Y3 4

3023

931

Y3 618 S9

S9 S9

Y3

X8

3011

686 S9

631 632

X8

6

S9

629

3016

690 1619

3021

3014

Y3 X8

3018

3017 X8

3020 X8

2130

7

3016 X8

3017

X8 3015

3013

3022

3020 X8

5

3001

633

3012

3018

8

Fig. 32 3rd Paper Tray (1/2)

287 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P Safety Mark

Ref. No. 3101 3102 3103 3104 3105

Part Number DZJM001321 DZKK000123 DZKQ000106 DZLA000359 FFPMQ0536

3106 DZLF000740 3111 DZLF000741 3113 3114 3115 3116 3117 3118 3119 3120 3121 3122 3123 3124 3125 3127 3128 3132 3133

DZJE001206 DZJE001205 DZJK000067 DZJK000068 DZJK000017 FFPHQ0063 FFPFJ00441 DZLF000733 FFPMF10281 FFPMF1029 DZLF000734 DZJA001412 FFPMF1031B DZJH000066 DZJH000026 DZTY000357 DZJA001568

Part Name Guide, Paper Tray Actuator, 2nd Paper Feed Spring, Return Roller, Intermediate Bushing, 8 Metal Gear 1, OP Paper Tray Idle Gear 3, OP Paper Tray Idle Cover, Heater Holder, Heater Clamp Clamp Edge Saddle Coupling 2 Ring, Stopper Gear, Lift Up Coupling Gear 2, Lift Up Gear 3, Lift Up Gear 1, Lift Up Case B, Lift Up Gear, Worm Spacer, PCB Spacer, PCB Assembly, Lift Up Drive Case A, Lift Up

New Parts C C C C C

Remarks

Destination All All All All All

C

All

C

All

C C C C C C C C C C C C C C C C C

All All All All All All All All All All All All All All All All All

3134 DZGG000072

Motor

C

All

3135 DZKN000412 3136 DZLF000732 3137 DZJM001076

Spring, Lift Up Gear, Lift Up 2 Sheet

C C C

All All All

3138 PJWQF2120PB

Assembly, Lift Motor

C

All

3301 DZJB000446 3302 DZLF000743 3303 DZLF000742

C C C

All All All

C

All

C

All

131

DZAL000211

Ring, Gap Gear 2, 3rd OP Drive Gear 1, 3rd OP Drive Assembly, 3rd OP Drive Plate Sensor, Photo

424

FFPCP0034

Heater

C

All

425 603 607 611 614 616 617 619

DZHD000036 DZLM000006 DZKL000083 DZKK000126 DZKQ000110 DZJF000651 DZJF000668 DZLA000363

Sleeve, Heater Bushing 2, P6L5 Lever, Paper Exit Sensor Latch, Arm Spring, Latch Guide, Front Guide, Feed Roller Roller, Pickup

C C C C C C C C

All All All All All All All All

3304 DZHP009929

PM

288 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P A

B

C

3132

Y3

E

694

S9

3105 G6

3123 3122 3121 3136

3124

D

3134

3104

3138

1

3133

3125

603 3102

3120 3304 680

3135 3103

3111 3118 S9

3303

3101 2919

3302

131

3106

699

688 3301

K9

667

3111 627

698

S9

614 611 H7

665

2919

695

668 Y3 131 620 S9

S9 S9 621 626

698 625

4

617

616 624

3128

622

2835

3115

3116 131

5

623 K5

3116 3127

Y2

666 Y3

619

2909

3

680

607

S9

3302

2

Y3

3119

3117

424 **** 425

3113 S9 6

Y2 680 3114

680 3137

681

931 7

8

Fig. 33 3rd Paper Tray (2/2)

289 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P Safety Mark

Ref. No. 620 621 622 623 624 625 626 627 665 666 667 668 680 681 688

Part Number

Part Name

New Parts C C C C PM C C C C C C N N

Remarks

Destination

DZKG000384 DZLF000711 DZLG000035 DZLA000360 DZLF000710 DZKQ000107 DZKG000383 DZJA001402 DZJB000438 DZJM001378 DZJM001381 DZJM001388

Shaft, Pickup Gear, Pickup Idler Clutch, One-way Roller, Feed Gear, Pickup Drive Spring, Pickup Shaft, Feed Bracket, Pickup Stay Feed Film, Guide Sheet, Guide Film, Guard

DZJK000004 DZJK000023 DZJA001427

Clamp Clamp Assembly, Latch Bracket

C C C

All All All All All All All All All All All All All All All

694

L9EAAK000009

Clutch, Micro 2

C

All

695

L9EAAK000010

Clutch, Micro 1

C

All

698 699 931 2835 2909

FFPMQ0649 DZJK000057 DZMC000821 DZFP001642 DZEC102749R

Bushing Clamp Plate, Base Harness, PTC-AC 4 PC Board, CST3 Harness, Paper Tray Sensor 2 Snap Ring Snap Ring E-Ring Snap Ring

C C C C C

All All All All All

2919 DZFP001614 G6 H7 K5 K9 S9 Y2 Y3

FFPFJ0039B FFPFJ0041B XUC5VM FFPFJ0043B FFPFJ0033B Snap Ring DZJM000171 or XTB3+6FFJ-RP Screw XTW3+6LFJ Screw

RTL/PbF

C

All

C C C C

All All All All

C

All

C C

All All

290 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P A

B

C

3132

Y3

E

694

S9

3105 G6

3123 3122 3121 3136

3124

D

3134

3104

3138

1

3133

3125

603 3102

3120 3304 680

3135 3103

3111 3118 S9

3303

3101 2919

3302

131

3106

699

688 3301

K9

667

3111 627

698

S9

614 611 H7

665

2919

695

668 Y3 131 620 S9

S9 S9 621 626

698 625

4

617

616 624

3128

622

2835

3115

3116 131

5

623 K5

3116 3127

Y2

666 Y3

619

2909

3

680

607

S9

3302

2

Y3

3119

3117

424 **** 425

3113 S9 6

Y2 680 3114

680 3137

681

931 7

8

Fig. 33 3rd Paper Tray (2/2)

291 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

5.20. Packing and Accessories 1. For USA and Canada Safety Mark

Ref. No.

Part Number

PJPGC0682Z PJPGC0723Z PJPGC0687Z 3405 PJPGC0724Z

Part Name

New Parts

Remarks

Destination

PU PUG PU For DP-8020P* PUG PU For DP-8016P PUG For DP-8020E

Box

N

3406 K2CH3DH00002

Cord, AC Power

C

PU, PUG

3407 PJJXC0230Z

Software CD CD (For Operating Instructions)

N

3409 PJQRC0172Z

Installation Instructions

N

PU, PUG PU, PUG Except PK, PT All

3410 PJQQC0065Z

Quick Guide

N

PU, PUG

3411 PJYCF2120PU0

Assembly, Cushion

C

3412 PJPGC0328Z

Pad

C

3413 PJPGC0371Z 3414 PJPAC0011Z 3416 DZNK004940

Box, Bottom Palette, Wooden Label, Paper Tray

C C C

3417 PJQRC0008Z

Important Notice

C

3420 PJPQC0038Z 3421 PJPQC0039Z

Process, Cushion R Process, Cushion L

C C

PU, PUG PU, PUG Except PK PU, PUG PU, PUG PU, PUG PU, PUG Except PK All All

PJPGC0690Z PJPGC0725Z

3408 PJJXC0228Z

N

292 Ver. 1.0

OCT 2006

A

B

C

D

DP-8020E/8020P/8016P E

1

2

3417

See Fig. 13, 14 3

3421 3420 3407, 3408 3409, 3410,

3411 3405 4

3416

3406 3411 5

3411 3412

3411

6

3413

7

3414

8

Fig. 34 Packing and Accessories

1. For USA and Canada

293 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

5.21. Packing and Accessories 2. For China Safety Mark

Ref. Part Number Part Name No. 3402 PJPAC0004Z Pad, Top PJPGC0683Z 3405 PJPGC0688Z Box PJPGC0691Z K2CK3DH00027 or 3406 Cord, AC Power DZFM000111 3407 PJJXC0234Z Software CD 3409 PJQRC0172Z Installation Instructions 3411 PJYCF2120PK0 Assembly, Cushion 3413 PJPGC0685Z Box, Bottom 3414 PJPAC0005Z Palette, Wooden

New Parts C N

Remarks

For DP-8020E For DP-8020P* For DP-8016P

Destination PK PK PK PK

C

PK

N N C N C

3416 DZNK004942

Label, Paper Tray

C

3417 PJQRC0025Z

Important Notice

C

PK All PK PK PK PK Except PU, PUG PK

3418 PJQMC0700Z

Operating Instructions

N

PK

3419 PJPGC0684Z 3420 PJPQC0038Z 3421 PJPQC0039Z

Angle, L Process, Cushion R Process, Cushion L

N C C

PK All All

294 Ver. 1.0

OCT 2006

A

B

C

D

DP-8020E/8020P/8016P E

1

3405

3417

2

See Fig. 13, 14 3402 3

3421 3420 3407 3409, 3418

3411

3411

4

3416 3406 3411

3411

3419 5

3413 6

3419

3414 7

8

Fig. 34 Packing and Accessories

2. For China

295 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

5.22. Packing and Accessories 3. For Other Destinations (except USA, Canada and China) Safety Mark

Ref. No.

Part Number

Part Name

New Parts

PJPGC0681Z 3405 PJPGC0686Z

For DP-8020E Box

N

PJPGC0689Z

Cord, AC Power

C

K2CT3DH00023 3407 PJJXC0232Z

For DP-8020P* For DP-8016P

K2CH3DH00002 DZFM000115 3406 K2CM3DH00013

Remarks

Destination Except PU, PUG, PK Except PU, PUG, PK Except PU, PUG, PK PT PA PF, PM, PP PS PB,PY

Software CD

N

Except PU, PUG, PK

CD (For Operating Instructions) Installation Instructions

N

Except PK, PT

N

Quick Guide

N

3411 PJYCF2120PB0

Assembly, Cushion

C

3412 PJPGC0328Z

Pad

C

3413 PJPGC0327Z

Box, Bottom

C

3416 DZNK004942

Label, Paper Tray

C

3417 3418 3420 3421

Important Notice Operating Instruction Process, Cushion R Process, Cushion L

C N C C

All PA, PB, PF, PM, PS PP PY Except PU, PUG, PK Except PK Except PU, PUG, PK Except PU, PUG, PK Except PK PT All All

3408 PJJXC0228Z 3409 PJQRC0172Z PJQQC0066Z 3410

PJQQC0069Z PJQQC0070Z

PJQRC0008Z PJQMC0713Z PJPQC0038Z PJPQC0039Z

296 Ver. 1.0

OCT 2006

A

B

C

D

DP-8020E/8020P/8016P E

1

2

3417

See Fig. 13, 14 3

3421 3420 3407, 3408

3409, 3410, 3418

3411

3405 4

3416 3406 3411 3411

5

3412

3411 6

3413

7

3. For Other Destinations (except USA, Canada and China)

8

Fig. 34 Packing and Accessories

297 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

5.23. Printer Controller Module for PCL6 Safety Mark

Ref. Part Number No. 3501 DZRB000143 PJJXC0257Z 3502 PJJXC0259Z PJJXC0261Z 3504 PJQRC0182Z 3505 ----------

Part Name Box

New Parts C

Software CD

N

Installation Instructions Hardware Key

N

Remarks

Destination All PU, PUG Other PK All

< Europe only > Safety Mark

Ref. Part Number No. 3501 DZRB000143 PJJXC0257Z 3502 PJJXC0259Z PJJXC0261Z 3503 DZSM000756 3504 PJQRC0182Z 3505 ---------822 DZJH000084 2805 DZEC103692

Part Name Box

New Parts C

Remarks

Destination

Software CD

N

Installation Instructions Installation Instructions Hardware Key Supporter, PC Board PC Board, FRM8

C N

All PU, PUG Other PK Europe only All

C C

Europe only Europe only

RTL/PbF

298 Ver. 1.0

OCT 2006

A

B

C

D

3501

DP-8020E/8020P/8016P E

3505

1

2

3502

3

3504 4

< Europe only > 2805 3501 5

822

3505

6

3502

7

3504

3503 8

Fig. 35 Printer Controller Module for PCL6

299 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

5.24. Printer Controller Module for PS/PCL6 Safety Mark

Ref. Part Number No. 3601 PJQRC0183Z PJJXC0263Z 3603 PJJXC0265Z PJJXC0267Z 3604 ---------3501 DZRB000143 3505 ----------

Part Name Installation Instructions

New Parts N

Software CD

N

Label, Adobe Postscript 3 Box Hardware Key

C

Remarks

Destination All PU, PUG Other PK All

< Europe only > Safety Mark

Ref. Part Number No. 3601 PJQRC0183Z PJJXC0263Z 3603 PJJXC0265Z PJJXC0267Z 3604 ---------822 DZJH000084 2805 DZEC103692 3501 DZRB000143 3503 DZSM000756 3505 ----------

Part Name Installation Instructions

New Parts N

Software CD

N

Label, Adobe Postscript 3 Supporter, PC Board PC Board, FRM8 Box Installation Instructions Hardware Key

C C C C

Remarks

Destination All PU, PUG Other PK

RTL/PbF

Europe only Europe only All Europe only

300 Ver. 1.0

OCT 2006

A

B

C

D

3501

DP-8020E/8020P/8016P E

3505

1

2

3603

3

3604 3601 4

< Europe only > 2805 3501 822

5

3505

6

3603

7

3503 3601

3604 8

Fig. 36 Printer Controller Module for PS / PCL6

301 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

5.25. Fax Communication Board Safety Mark

Ref. Part Number No. 3901 DZSM000813 3902 DZRB000733 PJJWC0009Z PJJWC0010Z PJJWC0011Z PFJA05B001Y PFJA04B006Y 3903

Part Name Installation Instructions Box, Carton

New Parts C C

Cord, Line

C

Label, TEL Label, LINE

C C

DZFN000136

DZFN000104 3904 DZNK005454 3905 DZNK005455 3906

DZQE000003

Rosette DZQE000005 PFJA05B001Y DZFB000022 DZFB000001 or Plug, PTT 3907 DZFB000035 DZFB000010 DZFB000009 or K2ME4B000001 DZJE001173 DZJE001213 505 Cover, Key DZJE001214 DZJE001216 506 DZNA001042 Key 513 DZKP000365 Spring, Speaker

C

C

N

C

C C

Remarks

Destination

All All ABR, AKR, AWR AGR AMR ARR,AVR ENR AER, AJR, ATR AUR, EER, YAR YCR, YGR, YMR YPR, YRR, YSR YTR, YVR, YWR YXR, YYR ARR All All YCR, YGR, YSR YVR, YAR, YYR APR AVR AAR ARR ARR ALR ALR AMR For DP-8020E/8020P* AUR, Other YVR AER AVR For DP-8020E/8020P* All All

514

DZHP010070

Assembly, Speaker

C

All

681 811 831 832 940

DZJK000023 DZJA001443 DZJK000079 DZJH000063 DZJK000070

Clamp Bracket, MJR PCB Clamp Spacer, PCB Clamp

C C C C C

All All All All All

302 Ver. 1.0

OCT 2006

A

B

C

D

DP-8020E/8020P/8016P E

1

1830

1829

3907

3903

3906

505, 506

832

2

2902, 811, 940

Y6

681 2915

2903, 831

3

X8

514 513

3804 4

3408 3802, 3803, 3908 3904 3905 5

3901

6

7

3902

8

Fig. 39 Fax Communication Board

303 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P Safety Mark

Ref. No.

New Parts

Remarks

Assembly, Stamp

C

For DP-8020E/8020P*

Unit, Stamp

C

Part Number

DZHP000237 DZHP000240 1830 DZHP005513

1829

Part Name

2902

Depends on Destination

PC Board, MJR

C

2903

Depends on Destination

PC Board, FXB

C

2915 DZFP001630

Harness, MJR-FXB

C

3909 DZHP010280

CD

C

Quick Guide

C

Operating Instructions

C

Firmware CD Notice Screw Screw

C N C C

3802

3803 3804 3908 X8 Y6

DZSD002231 DZSD002234 DZSD002232 DZSD002217 DZSD002219 PJJXC0042Z PJQHC0189Z XTB3+8GFJ XTW3+6LFJR

Destination

AUR Other For DP-8020E/8020P* All See Sect. 5.17 PC Boards (RTL/PbF) See Sect. 5.17 PC Boards (RTL/PbF) All Except YVR, AER AUR, YYR YPR, YRR Other YVR AER All All All All

304 Ver. 1.0

OCT 2006

A

B

C

D

DP-8020E/8020P/8016P E

1

1830

1829

3907

3903

3906

505, 506

832

2

2902, 811, 940

Y6

681 2915

2903, 831

3

X8

514 513

3804 4

3408 3802, 3803, 3908 3904 3905 5

3901

6

7

3902

8

Fig. 39 Fax Communication Board

305 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

5.26. Keyboard Option Safety Mark

Ref. No. 4001 4002 4003 4004 531 S6

Part Number DZSM000815 DZRH000621 DZRH000622 DZRB001070 ----DZPA000086

Part Name Installation Instructions Cushion, Top Cushion, Bottom Box, Carton

New Parts C C C C

Sheet, Keyboard

C

Screw

C

Remarks

Destination All All All All

See Sect. 5.4 All (Control Panel Unit) All

306 Ver. 1.0

OCT 2006

A

B

C

D

DP-8020E/8020P/8016P E

S6 1

4001

531

2

4002

3

See Fig. 5 4

4003 5

4004 6

7

8

Fig. 40 Keyboard Unit

307 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

5.27. Hard Disk Drive Unit Safety Mark

Ref. No. 4101 4102 4103 680 804 805 827 2803 2812 2813 2842 3116 Y3

Part Number

Part Name

New Parts C C C C

Remarks

Destination

DZRB000750 DZRB000580 DZSM000812 DZJK000004

Cushion, HD Box, Carton Installation Instructions Clamp

All All All All

M0CE00000028

HDD Unit

C

All

DZJE001207 DZPA000093 DZEC102176R DZFP001632 DZFP001651 DZFP001633 DZJK000068 XTW3+6LFJ

Cover, HDD Screw PC Board, DC Harness, DC Harness, HDD Harness, HDDPS Clamp Screw

C C C C C C C C

All All All All All All All All

RTL/PbF

308 Ver. 1.0

OCT 2006

A

B

C

DP-8020E/8020P/8016P E

D

1

4103

2

680

3116

Y3

2803

804

2812

827

2813

3

4101

2842

4

805

5

6

7

4102

8

Fig. 41 Hard Disk Drive Unit

309 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

5.28. Accounting Software Safety Mark

Ref. No. 4201

Part Number -----

4202 DZSM000741 3501 DZRB000143

Part Name

New Parts

Destination

Available as Sales Item

Accounting Software CD Installation Instructions Box

Remarks

C C

All All

310 Ver. 1.0

OCT 2006

A

B

C

D

DP-8020E/8020P/8016P E

1

2

3

3501

4201

4

5

4202 6

7

8

Fig. 42 Accounting Software

311 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

5.29. i-ADF Packing and Accessories Safety Mark

Ref. No. 4301 4303 4306 104 2112 2113 2114 2131 X6 F7 M2 W9

Part Number DZHP011187 DZHP011186 DZJM001402 DZSM000551 PJHEC0124Z PJUIC0254Z DZMC000713 DZJA000726 DZMA004372 XTB3+8JFJ XSN4+W10FN DZPA000064 XTB3+12JFJ

Part Name

New Parts

Packing, i-ADF

C

Actuator, ADF Installation Instructions Pad, Scanning Bracket, ADF Mounting Cover, Hinge Stopper, Hinge Cover 2, Hinge Screw Screw Screw, Thumb Screw

C C C C C C C C C C C

Remarks

Not Used

Destination PU,PUG Other All All All All All All All All All All All

312 Ver. 1.0

OCT 2006

A

B

C

D

DP-8020E/8020P/8016P E

1

4301

4301 2

2114

W9

X6 3

4303

F7

M2 2112

4

2113

4306 104 5

2113

2112 2131

4301 2131 4301 6

7

4301

8

Fig. 43 i-ADF Packing and Accesories

313 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

5.30. ADF Packing and Accessories Safety Mark

Ref. No.

Part Number

Part Name

New Parts

DZHP011700 4401 4404 4406 1801 1822 6A B1

DZHP011701 DZSM000523 DZRH000479 DZJA000858 PJZEF21200PU XTB3+12GFJ DZPB000007

Packing, ADF

C

Installation Instructions Sheet, Cushion Plate, Angle Scanning Pad Screw Screw, Silver

C C C C C C

Remarks

Destination PU, PUG, PT Except PU, PUG, PT All All All All All All

314 Ver. 1.0

OCT 2006

A

B

C

DP-8020E/8020P/8016P E

D

4401 1

4401 2

4401 3

1801

6A 4

1822

B1

4406 4404

5

4401

4401

6

4401

7

8

Fig. 44 ADF Packing and Accesories

315 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

5.31. 2nd/4th Paper Tray and 3rd Paper Tray Packing and Accessories Safety Mark

Ref. No.

4501

4502 4504 4505 X8 Y3

Part Number DZRB001141 DZRB001145 DZRB001142 DZRB001146 DZRB001139 DZRB001143 DZRB001140 DZRB001144 DZRH000601 DZSM000811 DZNK005417 DZNK005420 DZNK005416 XTB3+8GFJ XTW3+6LFJ

Part Name A B A B A B A B

New Parts

Remarks

For 2nd/4th Paper Tray

Destination PU, PUG Other

Box, Carton

C PU,PUG For 3rd Paper Tray Other

Assembly, Cushion Installation Instructions

C C

Label, Paper Size

C

Screw Screw

C C

All All PU, PUG PK Other All All

Note: A: Carton Box depicts Made in Japan. B: Carton Box depicts Made in Philippines.

316 Ver. 1.0

OCT 2006

A

B

C

D

DP-8020E/8020P/8016P E

1

4502

2

4502

Y3

4504 4505

X8 3

See Fig. 16, 30-33

4

4502 5

4501 6

7

Fig. 45 2nd / 4th Paper Tray and 3rd Paper Tray Packing and Accesories

8

317 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

5.32. Dehumidifier Heater Kit (For Main Unit) Safety Mark

Ref. Part Number No. 4601 DZRB000101 4602 DZSM000818 DZNK005283 224 PJGTC0053Z

Box, Carton Installation Instructions Label, Heater Main

C

225

DZNK005284

Label, Switch

C

All

404

DZJA001439

405 424

Part Name

New Parts C C

Remarks

Destination All All PU, PUG, Other PK

C

All

DZJA001438

Bracket, Dehumidifier Heater Bracket, Harness

C

All

FFPCP0034

Heater

C

All

425 429 430 680 681 808 809

DZHD000036 DZJK000045 DZJK000046 DZJK000004 DZJK000023 DZJA001436 DZJA001437

Sleeve, Heater Clamp Clamp Clamp Clamp Bracket, RLB SW Bracket, RLB PCB

C C C C C C C

All All All All All All All

814

DZCC000006

Switch, Power

C

All

FFPKD07791 PJWPF2740AZ

Bracket, Heater PC Board, RLB Harness, PTC-AC 1 Harness, PTC-AC 3 Harness, RLB Harness, PTC-AC 2 Clamp Spacer, PCB Screw Screw

C C C C C C C C C C

All All All All All All All All All All

936 2804 2830 2831 2833 2834 3116 3128 Y2 Y3

DZFP001639 DZFP001641 DZFP001653 DZFP001640 DZJK000068 DZJH000026 XTB3+6FFJ-RP XTW3+6LFJ

318 Ver. 1.0

OCT 2006

A

B

C

Y3

D

DP-8020E/8020P/8016P E

Y2 405

681

1

404 680 429 430

2

3116 936 424, 425 424 2834

3

2830 2831 808, 814 2833

4602

4

224 5

809, 2804, 3128, Y3 225 6

7

4601

8

Fig. 46 Dehumidifier Heater Kit (For Main Unit)

319 Ver. 1.0

OCT 2006

5.33. Dehumidifier Heater Kit (For Optional Paper Tray(s)) Safety Mark

Ref. Part Number No. 4701 DZSM000820 424 681 2835 3113 3114 3115 3117 3501 Y2

Part Name Installation Instructions

New Parts C

Remarks

DP-8020E/8020P/8016P

Destination All

FFPCP0034

Heater

C

All

DZJK000023 DZFP001642 DZJE001206 DZJE001205 DZJK000067 DZJK000017 DZRB000143 XTB3+6FFJ-RP

Clamp Harness, PTC-AC 4 Cover, Heater Holder, Heater Clamp Edge Saddle Box Screw

C C C C C C C C

All All All All All All All All

320 Ver. 1.0

OCT 2006

A

B

C

DP-8020E/8020P/8016P E

D

1

3501 2

3

3117

4

2835 3115

3114 3113

681 Y2 5

424 4701 6

7

Fig. 47 Dehumidifier Heater Kit (For Optional Paper Tray(s))

8

321 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

5.34. Key Counter Harness Kit Safety Mark

Ref. No. 4801 4802 237 238 239 940 951 2861 Y2 Y3 Y11

Part Number DZSM000825 DZTT000711 PJUIC0218Z PJUIC0219Z PJUIC0221Z DZJK000070 DZJB000463 DZFP001902 XTB3+6FFJ-RP XTW3+6LFJ XSB4+10FJ

Part Name Installation Instructions Box, Carton Base, Key Counter Cover, Key Counter Cover, Key Counter Front Clamp Guide, Counter Harness, KEY Screw Screw Screw

New Parts C C C C C C C C C C C

Remarks

Destination All All All All All All All All All All All

322 Ver. 1.0

OCT 2006

A

B

C

DP-8020E/8020P/8016P E

D

1

2

2861 4801 3

Y11

238 237

Y2

4

940 Y3

239 951 5

6

4802

7

8

Fig. 48 Key Counter Harness Kit

323 Ver. 1.0

OCT 2006

5.35. Hardware Identification Template Figure

DP-8020E/8020P/8016P

Ref. No.

Part No.

Remark

18

XYN3+F6FJ

Screw

62

XTB3+6JFJ

Screw

1N

XTB4+8JFJ

Screw

3F

XYN3+F5FJ

Screw

5M

XYN3+F4FJ

Screw

5Z

XUC6VM

E-Ring

6A

XTB3+12GFJ

Screw

B1

DZPB000007

Silver Screw

B4

XTB3+8JFI

Blue Screw

C2

DZPB000020

Screw

E8

XTW3+10SFJ

Screw

F7

XSN4+W10FN

Silver Screw

G6

FFPFJ0039B

Snap Ring

H7

FFPFJ0041B

Snap Ring

J6

XUC3VM

E-Ring

J7

XUC4VM

E-Ring

324 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Ref. No.

Part No.

Figure

Remark

J8

XUC7VM

E-Ring

K5

XUC5VM

E-Ring

K9

FFPFJ0043B

Snap Ring

M2

DZPA000064

Thumb Screw

Q8

XTB3+8GFN

Screw

S6

DZPA000086

Screw

S9

FFPFJ0033B

Snap Ring

W9

XTB3+12JFJ

Screw

X1

XTB3+10GFJ

Screw

X2

DZPA000089

Screw

X3

XYN3+F8FJ

Screw

X4

XTB3+20GFJ

Screw

X6

XTB3+8JFJ

Screw

X7

XYN3+F14FJ

Screw

X8

XTB3+8GFJ

Screw

X9

XTB3+8FFJ

Screw

Y1

XTW3+8PFJ

Screw

325 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Ref. No.

Part No.

Figure

Y2

XTB3+6FFJ-RP

Screw

Y3

XTW3+6LFJ

Screw

Y4

XTB3+32GFJ

Screw

Y5

XSN3+W10FJ

Screw

Y6

XTW3+6LFJR

Screw

Y7

XNC3FJ

Nut

Y8

XTN3+10GFJ

Screw

Y9

XYN4+F8FJ

Screw

Y10

XYN4+F6FJ

Screw

Y11

XSB4+10FN

Screw

Remark

326 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

memo

327 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

6 Alphanumerical Parts List Alphanumerical Parts List Part Number ------------------------------------CR2032 DNQ18AS14W26

DZAL000211 DZBL000061 DZCC000006 DZCC000011 DZCF000022 DZDG000177 DZDX000003 DZEA000088

Part Name Sheet, Keyboard Accounting Software CD Hardware Key Label, Adobe Postscript 3 Battery Motor, Drive Drum, OPC (Available as Sales Item) Assembly, Toner Bottle (Available as Sales Item) Assembly, Toner Bottle (Available as Sales Item) Assembly, Toner Bottle (Available as Sales Item) Sensor, Photo Assembly, Thermistor Switch, Power Switch, Power Switch, Cover Open Coil 2 Thermostat PC Board, Inverter

DZEC101648R

PC Board, ADF

2847

DZEC102176R DZEC102303R DZEC102304R DZEC102749R DZEC102751R DZEC102830R DZEC102911R DZEC102912R DZEC102913R DZEC102917R DZEC103049R DZEC103116R DZEC103117R DZEC103157R DZEC103665 DZEC103692 DZEC103793

PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC

2803 2846 2832 2909 2806 2807 2904 2905 2906 2910 2907 2903 2903 2910 2908 2805 2902

DZEC103795

PC Board, MJR

2902

RTL/PbF

DZEC103797

PC Board, MJR

2902

RTL/PbF

DZEC104116 DZEC104117 DZEC104118 DZEC104119 DZEC104120

PC PC PC PC PC

2801 2801 2801 2801 2801

For For For For For

DQ-H60J-PU DQ-TU10J-PB DQ-TUJ10K-PK DQ-TUJ10K-PU

Board, Board, Board, Board, Board, Board, Board, Board, Board, Board, Board, Board, Board, Board, Board, Board, Board,

Board, Board, Board, Board, Board,

DC ADF SNS CST3 WTS PCL PNL1 PNL2 PNL3 SSN PNL4 FXB FXB SSN CST2 FRM8 MJR

SC SC SC SC SC

Ref. No. Remarks Destination 531 Control Panel Unit All 4201 Available as Sales Item 3505 3604 504* All 1511 All 1403

PM

All

1216

PM

Other

1216

PM

PK

1216

PM

PU, PUG

131 1125 814 818 1918 820 1120 416

PM

For DP-8016P For DP-8020E (RTL/PbF) RTL/PbF RTL/PbF RTL/PbF

RTL/PbF

For DP-8020E/8020P* RTL/PbF RTL/PbF RTL/PbF RTL/PbF RTL/PbF

DP-8016P (RTL/PbF) DP-8020P*(RTL/PbF) DP-8020E (RTL/PbF) DP-8016P (RTL/PbF) DP-8020P*(RTL/PbF)

All All All All All Except PU, PT, PUG All All All All All All All All All All All All Except PK, PT All AUR Except AUR PK, PT All Europe only AUR AAR, ABR, AGR, AHR, AJR, ALR, AMR, APR, ARR, AVR, EER, ENR, YGR, YPR, YXR Except AAR, ABR, AGR, AHR, AJR, ALR, AMR, APR, ARR, AUR, AVR, EER, ENR, YGR, YPR, YXR PU, PUG PU, PUG PU, PUG PB, PY PB, PY

328 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Alphanumerical Parts List Part Number DZEC104121 DZEC104122 DZEC104123 DZEC104124 DZEC104125 DZEC104126 DZEC104127 DZEC104128 DZEC104129 DZEC104130 DZEC104131 DZEC104132 DZEC104133 DZEC104134 DZEC104135 DZEC104136 DZEC104137 DZEC104138 DZEC104139 DZEC104140 DZEC104141 DZEC104142 DZEC104147 DZFA000098 DZFB000001 DZFB000009 DZFB000010 DZFB000022 DZFB000035 DZFC001575 DZFC001576 DZFM000111 DZFM000115 DZFN000104

Part Name PC Board, SC PC Board, SC PC Board, SC PC Board, SC PC Board, SC PC Board, SC PC Board, SC PC Board, SC PC Board, SC PC Board, SC PC Board, SC PC Board, SC PC Board, SC PC Board, SC PC Board, SC PC Board, SC PC Board, SC PC Board, SC PC Board, SC PC Board, SC PC Board, SC PC Board, SC PC Board, SPC Inlet Plug, PTT Plug, PTT Plug, PTT Plug, PTT Plug, PTT Connector, TR2 Connector 3 Cord, AC Power Cord, AC Power Cord, Line

Ref. No. 2801 2801 2801 2801 2801 2801 2801 2801 2801 2801 2801 2801 2801 2801 2801 2801 2801 2801 2801 2801 2801 2801 2802 945 3907 3907 3907 3907 3907 2435 2418 3406 3406 3903

DZFN000136

Cord, Line

3903

DZFP000747 DZFP001377 DZFP001533 DZFP001534 DZFP001587 DZFP001588 DZFP001589 DZFP001590 DZFP001592 DZFP001593 DZFP001594 DZFP001595 DZFP001596 DZFP001597 DZFP001598 DZFP001599 DZFP001600 DZFP001601 DZFP001602 DZFP001603

Resistor, 200M ohm Harness, i-ADF Harness, PNL2 1 Harness, PNL2 2 Harness, PS Harness, ILS Harness, Thermistor 2 Harness, MPS Harness, SSN Harness, SCN Harness, INV Harness, WTS Harness, LSU 1 Harness, Paper Tray Sensor Harness, SNS Harness, ACIN Harness, ACSW Harness, HT Harness, HV 1 Harness, BSMT

717 2827 2923 2924 2815 2823 2818 2841 2821 2828 2829 2819 2826 2820 2817 2913 2914 2925 2912 2822

Remarks For DP-8020E (RTL/PbF) For DP-8016P (RTL/PbF) For DP-8020P*(RTL/PbF) For DP-8020E (RTL/PbF) For DP-8016P (RTL/PbF) For DP-8020P*(RTL/PbF) For DP-8020E (RTL/PbF) For DP-8016P (RTL/PbF) For DP-8020P*(RTL/PbF) For DP-8020E (RTL/PbF) For DP-8016P (RTL/PbF) For DP-8020P*(RTL/PbF) For DP-8020E (RTL/PbF) For DP-8016P (RTL/PbF) For DP-8020P*(RTL/PbF) For DP-8020E (RTL/PbF) For DP-8016P (RTL/PbF) For DP-8020P*(RTL/PbF) For DP-8020E (RTL/PbF) For DP-8016P (RTL/PbF) For DP-8020P*(RTL/PbF) For DP-8020E (RTL/PbF) RTL/PbF

For DP-8020E

Destination PB, PY PM PM PM PF PF PF PS PS PS PP PP PP PA PA PA PK PK PK PT PT PT All All ARR ALR ALR AAR ARR All All PK PA ARR AER, AJR, ATR, AUR, EER, YAR, YCR, YGR, YMR, YPR, YRR, YSR, YTR, YVR, YWR, YXR, YYR All Other All All All All All All All All All All PU, PT, PK, PUG All All All All All All All

329 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Alphanumerical Parts List Part Number DZFP001604 DZFP001605 DZFP001606 DZFP001607 DZFP001608 DZFP001611 DZFP001612 DZFP001613 DZFP001614 DZFP001615 DZFP001616 DZFP001617 DZFP001620 DZFP001622 DZFP001623 DZFP001624 DZFP001627 DZFP001628 DZFP001629 DZFP001630 DZFP001632 DZFP001633 DZFP001634 DZFP001635 DZFP001636 DZFP001639 DZFP001640 DZFP001641 DZFP001642 DZFP001650 DZFP001651 DZFP001653 DZFP001672 DZFP001674 DZFP001705 DZFP001710 DZFP001711 DZFP001712 DZFP001713 DZFP001714 DZFP001902 DZFP001964 DZFP001965 DZFP001966 DZFP001967 DZFP001968 DZFP001969 DZFP001971

Part Name Harness, Toner Sensor Harness, PCL PCB Harness, Thermistor 1 Harness, DUPSEN Harness, HEPESEN Harness, Paper Tray 2 Harness, Paper Tray 3 Harness, CL2 Harness, Paper Tray Sensor 2 Harness, CL3 Harness, Frame Ground Harness, HV 2 Harness, SC-SPC Harness, CCD Harness, LSU 2 Harness, CSS Harness, PNL1-PNL3 A Harness, PNL1-PNL3 B Harness, PNL1-PNL4 Harness, MJR-FXB Harness, DC Harness, HDDPS Harness, PNL1 Harness, PNL1 Harness, PNL1 Harness, PTC-AC 1 Harness, PTC-AC 2 Harness, PTC-AC 3 Harness, PTC-AC 4 Inlet Harness Harness, HDD Harness, RLB Harness, ADF Clutch Harness, B1 Sensor Harness, ADF Motor and Clutch Harness, CLT Harness, SNS Harness, Read Point Sensor Harness, Exit Sensor Harness, ADF-FG Harness, KEY Harness, ADF Motor Harness, PNT/REV Harness, Open Switch Harness, Stamp Harness, ADF SNS Harness, ADF Harness, i-ADF

Ref. No. 2836 2837 2838 2844 2839 2825 2921 2920 2919 2922 2840 2911 2816 2811 2814 2843 2916 2917 2918 2915 2812 2842 2810 2810 2810 2830 2834 2831 2835 946 2813 2833 2854 2857 2853 2855 2856 2858 2859 2860 2861 2848 2849 2850 2852 2851 2827 2827

DZFP002104

Harness, LSU 1B

2826

DZFP002105

Harness, LSU 2B

2814

DZGB000045 DZGD000001 DZGD000005 DZGG000072 DZGG000074 DZGG000075 DZGG000076 DZGK000471

Solenoid Magnet Roller, Magnetic Motor Motor, Scanning Fan, Rear Fan, PS Shaft, Reverse Roller

1512 208 1306 3134 316 815 816 654

Remarks

For DP-8020E

For DP-8020E For DP-8020P* For DP-8016P

For For For For For For For

DP-8020E DP-8020E DP-8020E DP-8020E DP-8020E DP-8020E DP-8020E

For DP-8020E/8020P*

For DP-8020E

For DP-8020E

For DP-8016P

Destination All All All All All All All All All All All All All All PU, PT, PK, PUG All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All PK, PT, PU, PUG Except PU, PT, PK, PUG Except PU, PT, PK, PUG All All All All All All All All

330 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Alphanumerical Parts List Part Number DZGM000011 DZGN000052 DZGN000053 DZGT000007 DZGT000032 DZHA000225 DZHA000226 DZHA000227 DZHC000057 DZHC000102 DZHC000103 DZHC000104 DZHC000105 DZHC000168 DZHC000169 DZHC000170 DZHC000172 DZHC000173 DZHD000036 DZHD000038 DZHD000039 DZHD000040 DZHE000055 DZHE000056 DZHE000057 DZHE000058 DZHE000059 DZHE000060 DZHE000067 DZHE000068 DZHE000069 DZHE000070 DZHE000071 DZHE000072 DZHE000073 DZHE000074 DZHP000237 DZHP000240 DZHP001664 DZHP003955 DZHP005513 DZHP009894 DZHP009898 DZHP009912 DZHP009928 DZHP009929 DZHP009933 DZHP009941 DZHP009942 DZHP009943 DZHP010070 DZHP010280 DZHP010630 DZHP010631 DZHP010632 DZHP010737 DZHP010738 DZHP010765R DZHP010766R DZHP011186

Part Name Lamp, Scanning Lamp, Fuser Lamp, Fuser Brush, Antistatic Brush, Discharge Cover 2, Harness Cover, Charge Cover, Rear Charge Actuator, Original Length Actuator 2 Actuator 3 Actuator, Sensor B2 Actuator, Sensor C Actuator Sheet, Blind Cover 1, Harness Plate Sheet Sleeve, Heater Cover, PS Sheet A Sheet, Radiation Duct, Upper Duct, Lower Cover, Fan Sponge, Developer Duct, Exit Filter, Ozone Sponge, Cover L Sponge, Cover Angle Sponge, Cover S Sponge, Cover M Seal, Developer Side Sponge, Developer Side Sponge, Doctor Blade(Side A) Sponge, Doctor Blade(Side B) Assembly, Stamp Assembly, Stamp Base, Stamp Assembly, Torque Limiter Unit, Stamp Container, Toner Waste Assembly, Drive Shaft Assembly, Fuser Drive Plate Assembly, OP Paper Tray Plate Assembly, 3rd OP Drive Plate Developer Unit Bracket, Front Cover Bracket, Rear Cover Plate, Duplex Drive Assembly, Speaker CD Assembly, Document Plate Assembly, Document Plate Assembly, Document Plate Torque Limiter 2 Torque Limiter 1 Assembly, ADF Tray Assembly, ADF Tray Packing, i-ADF

Ref. No. 410 1116 1116 1719 703 1326 1432 1438 1709 2622 2627 2522 2520 1106 1434 403 1453 1452 425 801 1012 1401 942 943 828 1303 823 825 1352 1353 1354 1359 1355 1356 1357 1358 1829 1829 2125 2525 1830 1201 304 1518 3112 3304 1347 744 745 746 514 3909 109 109 109 691 690 2211 2211 4301

Remarks PM PM

PM

For DP-8020E/8020P* For DP-8020E/8020P* For DP-8020E/8020P* For DP-8020E/8020P* PM

For DP-8020E

PM PM

Destination All PU, PT, PUG Other All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All AUR Other All All All All All All All All All All All All All Except YVR, AER Other PK, PT PU, PUG All All PU,PUG Except PU, PUG Other

331 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Alphanumerical Parts List Part Number DZHP011187 DZHP011700 DZHP011701 DZHP012149 DZHT000004 DZHT000027 DZJA000187 DZJA000675 DZJA000677 DZJA000678 DZJA000679 DZJA000680 DZJA000681 DZJA000684 DZJA000685 DZJA000688 DZJA000689 DZJA000693 DZJA000694 DZJA000695 DZJA000696 DZJA000697 DZJA000699 DZJA000726 DZJA000848 DZJA000849 DZJA000850 DZJA000851 DZJA000852 DZJA000853 DZJA000854 DZJA000855 DZJA000856 DZJA000858 DZJA001172 DZJA001190 DZJA001365 DZJA001366 DZJA001367 DZJA001368 DZJA001369 DZJA001370 DZJA001371 DZJA001372 DZJA001373 DZJA001374 DZJA001375 DZJA001376 DZJA001377 DZJA001378 DZJA001379 DZJA001380 DZJA001384 DZJA001385 DZJA001386 DZJA001387 DZJA001388 DZJA001389 DZJA001390 DZJA001391

Part Name Packing, i-ADF Packing, ADF Packing, ADF Roller Feed Bypass Assy Stamp Head Stamp Head Bracket, Magnet Bracket, Actuator Plate 1, Adjustment Plate, Adjustment 2 Bracket, Solenoid Bracket, Front ADF Cover Bracket, Rear ADF Cover Holder, Sensor B2 Bracket, Reversing (Guide 1) Guide, Skew Guide, White Reference Seal Plate, Reinforcement A Plate, Reinforcement B Bracket, Gear Bracket, Sensor Bracket, Moving Gear Bracket, Actuator Stopper, Hinge Bracket, Right Bracket, Motor Guide, White Bracket, Pulley Bracket, Substrate Bracket, Left Hinge Bracket, Adjust Bracket, Hinge Right Plate, Hinge Right Plate, Angle Bracket, Center Cover, ADF PC Board Bracket, Right Keyboard Bracket, Left Keyboard Bracket, Connector Bracket, LSU 2 Frame, SC Post, Front SC Post, Rear SC Bracket, LSU 1 Bracket, Toner Bracket, Bottle Shield, Front Side Shield, Rear Side Bracket, PS Cover Base, PS Bracket, PS Plate, Front Bias Cover, CCD Bracket, Left Hinge Bracket, Right Hinge Rail, Front Rail, Rear Base, Mirror 2 Holder, Rear Mirror Holder, Front Mirror

Ref. No. 4301 4401 4401 671 1827 1827 207 2617 2626 2709 2402 2621 2620 2521 2413 2702 2106 2306 2305 2602 2120 2409 2206 2114 1914 1906 1815 1913 1703 1802 1901 1816 1821 1801 2033 1916 534 535 916 905 904 903 902 908 914 909 1311 1310 813 810 802 1316 406 112 113 310 309 417 423 419

Remarks

For DP-8020E/8020P* For DP-8020E/8020P*

For DP-8020E/8020P* For DP-8020E/8020P*

Destination PU, PUG PU, PUG, PT Except PU, PUG, All Other AUR All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All

332 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Alphanumerical Parts List Part Number DZJA001392 DZJA001393 DZJA001394 DZJA001395 DZJA001396 DZJA001397 DZJA001398 DZJA001399 DZJA001400 DZJA001401 DZJA001402 DZJA001405 DZJA001406 DZJA001407 DZJA001409 DZJA001412 DZJA001413 DZJA001414 DZJA001420 DZJA001422 DZJA001425 DZJA001427 DZJA001436 DZJA001437 DZJA001438 DZJA001439 DZJA001443 DZJA001459 DZJA001460 DZJA001461 DZJA001462 DZJA001466 DZJA001467 DZJA001468 DZJA001469 DZJA001470 DZJA001471 DZJA001472 DZJA001473 DZJA001568 DZJB000186 DZJB000420 DZJB000421 DZJB000422 DZJB000424 DZJB000425 DZJB000426 DZJB000427 DZJB000428 DZJB000429 DZJB000430 DZJB000431 DZJB000432 DZJB000434 DZJB000435 DZJB000436 DZJB000437 DZJB000438 DZJB000440 DZJB000441

Part Name Bracket, Motor Plate, Front Spring Plate, Rear Spring Frame A, Main Drive Plate, Terminal 1 Plate, Terminal 2 Plate, Terminal 3 Frame B, Main Drive Bracket, Drive Cover Cover B, Main Drive Bracket, Pickup Bracket, Registration Sensor Bracket, Front Guide Bracket, Rear Guide Plate, Knob Case B, Lift Up Frame A, Bottle Drive Frame B, Bottle Drive Bracket, Reverse Hopper Unit Stopper, Release Assembly, Latch Bracket Bracket, RLB PCB SW Bracket, RLB PCB Bracket, Harness Bracket, Dehumidifier Heater Bracket, MJR PCB Bracket, Rear ADF Bracket, Front ADF Plate, Release Lever Bracket, Reversing (Guide 2) Bracket, Inverting Guide Front Bracket, Inverting Guide Rear Bracket, Motor Bracket, Pulley Hinge, Arm Base, Left Hinge (A) Plate, Reinforcement Base, Right Hinge (B) Case A, Lift Up Plate, Magnet Frame, Developer Frame, Center Holder, Bottle Frame, Pipe Bracket, Interlock SW Base, Paper Tray L Base, Right Paper Tray Bracket, Paper Tray Base Frame, Upper Fuser Frame, Lower Scanner Frame, Upper Scanner Frame, CCD Base, Separator Base, Left Paper Tray Bracket, Rear Upper Bracket, Rear Center Bracket, Feed Bracket, SPC PCB Frame, Left Scanner

Ref. No. 313 1124 1111 1514 1117 1119 1121 1515 3009 1516 627 606 663 661 1014 3124 1501 1502 632 1217 725 688 808 809 405 404 811 2501 2401 2504 2416 2426 2427 2610 2613 2102 2322 2103 2105 3133 213 1312 934 1203 1339 228 944 3011 3012 1110 401 301 402 1108 3014 3005 3006 665 926 907

Remarks

Destination All All All All All All All All All All All All All All All All All All All Other All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All

333 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Alphanumerical Parts List Part Number DZJB000442 DZJB000443 DZJB000444 DZJB000445 DZJB000446 DZJB000447 DZJB000449

Part Name Frame, Right Scanner Bracket, Inlet Bracket, Rear Cover, CST Ring, Gap Angle, Door Cover Holder, Filter

DZJB000459

Base, CHC

DZJB000463 DZJC000378 DZJC000379 DZJC000380 DZJC000381 DZJC000382 DZJC000383 DZJC000384 DZJC000385 DZJC000386 DZJC000387 DZJC000391 DZJC000392 DZJC000395 DZJD000038 DZJD000039 DZJD000040 DZJD000041 DZJD000042 DZJD000043 DZJD000044 DZJE001165 DZJE001167 DZJE001169 DZJE001171 DZJE001173 DZJE001175 DZJE001177 DZJE001179 DZJE001180 DZJE001181 DZJE001184 DZJE001185 DZJE001186 DZJE001188 DZJE001189 DZJE001191 DZJE001194 DZJE001195 DZJE001196 DZJE001199 DZJE001200 DZJE001202 DZJE001205 DZJE001206 DZJE001207 DZJE001213 DZJE001214 DZJE001216 DZJE001218 DZJE001219

Guide, Counter Plate, SA Guide, Bottle Shutter Bracket, PS SW Plate, Wire Lock Plate, Rear Wire Holder Plate, Front Wire Holder Plate, Pulley Holder, Rear Lamp Holder, Front Lamp Guide, Shaft Holder, Sleeve Carrier, Sleeve Block Plate, Engine FU Plate, Engine FL Bracket, Right Post Bracket, Left Post Bracket, Front Post Holder, Rear Engine Holder, Contact Spring Cover, Panel Cover, Control Panel Base Cover, Control Panel (Sub Base) Cover, Aperture Cover, Key Holder, Battery Cover, Keyboard Cover, Keyboard Lower Holder, Rear Bottle Frame, Lower Cover, Pipe Cover, Gear Cover, Developer Plate, Rear Document Plate, Rear Document Plate, Rear Document Cover, Exit Roller Cover, Fuser Roller Cover, Front Paper Tray Cover, Rear Fuser Cover, Front Fuser Cover, Printer Holder, Heater Cover, Heater Cover, HDD Cover, Key Cover, Key Cover, Key Cover, Panel Cover, Panel

Ref. No. 901 924 928 923 3301 205 824

Remarks

941 951 912 1212 807 412 413 414 418 1122 1123 647 2118 2116 1350 918 915 3003 3023 3013 933 930 502 529 530 537 505 503 533 536 1208 1305 1335 1318 1302 107 107 107 1101 1126 3001 1006 1007 726 3114 3113 805 505 505 505 502 502

For DP-8016P For DP-8020E/8020P* For DP-8020E/8020P* For DP-8020E/8020P*

For DP-8020E/8020P* For DP-8020E/8020P* For DP-8020E/8020P*

Destination All All All All All All All Except PU, PT, PUG, PK All All All All All All All All All All All All All All All All All All All All All PU,PUG,Other All All All AUR, Other All All All Other All All All All Other PU, PUG PK, PT All All All All All All All All All YVR AER AVR PF PK

334 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Alphanumerical Parts List Part Number DZJE001221 DZJE001223 DZJE001299 DZJE001308 DZJF000407 DZJF000408 DZJF000409 DZJF000414 DZJF000462 DZJF000489 DZJF000645 DZJF000646 DZJF000648 DZJF000649 DZJF000650 DZJF000651 DZJF000652 DZJF000653 DZJF000654 DZJF000655 DZJF000656 DZJF000657 DZJF000658 DZJF000659 DZJF000661 DZJF000662 DZJF000668 DZJF000702 DZJG000013 DZJH000026 DZJH000063 DZJH000066 DZJH000084 DZJH000126 DZJH000127 DZJH000128 DZJJ000009 DZJJ000017 DZJK000004 DZJK000017 DZJK000018 DZJK000023 DZJK000045 DZJK000046 DZJK000057 DZJK000067 DZJK000068 DZJK000070 DZJK000079 DZJK000106 DZJL000023 DZJL000115 DZJL000215 DZJL000362 DZJL000394 DZJL000395 DZJL000396 DZJL000397 DZJL000398 DZJL000399

Part Name Cover, Panel Frame, Lower Assy Holder, Rear Bottle Holder, Rear Bottle Guide, Upper ADF Guide, Lower ADF Guide, Sub Top Guide, E Guide, Card Leg, Gum Guide, Pressure Roller Guide, Fuser Roller Guide, Wire Guide, Front Guide, Upper Guide, Front Tray, Guide Guide, Duplex Guide Guide, Lower Guide, Duplex Guide, Front Set Guide, Rear Set Guide, Transfer Guide, Duplex 2 Lever, Guide Guide, Feed Roller Guide, SC PCB Fly Wheel Spacer, PCB Spacer, PCB Spacer, PCB Supporter, PC Board Bracket, Paper Feed Collar, Stopper Spacer, BTR Ring Band Wire, Front Door Clamp Edge Saddle Clamp Clamp Clamp Clamp Clamp Clamp Clamp 2, Locking Clamp Clamp Holder, Lamp Harness Plate, Ground Bushing Holder, TDC Sensor Plate, Nut Plate, Rear Bias Wire, Rear Wire, Front Plate, Pressure Shaft, OPC Case, Charge

Ref. No. 502 1025 1208 1208 2502 2505 2705 1607 833 3017 1010 1105 307 1023 615 616 650 638 659 634 739 129 128 718 732 133 617 1001 1555 3128 832 3127 822 3010 643 705 2124 226 680 3117 1915 681 429 430 699 3115 3116 940 831 311 947 2321 1332 1405 1325 303 305 649 1445 1444

Remarks

For DP-8020E/8020P*

For DP-8020E

For DP-8020E

For DP-8020E/8020P*

Destination PT All PK PU, PUG All All All All All All All All All All All All All All All All All All All All All All All All All All All All Europe only All All All All All All All All All All All All All All All All All All All All All All All All All All All

335 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Alphanumerical Parts List Part Number DZJL000400 DZJL000401 DZJL000402 DZJL000403 DZJL000404 DZJL000414 DZJM000013 DZJM000159 DZJM000171 DZJM000377 DZJM000406 DZJM000407 DZJM000408 DZJM000409 DZJM000410 DZJM000411 DZJM000412 DZJM000413 DZJM000414 DZJM000415 DZJM000416 DZJM000418 DZJM000419 DZJM000420 DZJM000421 DZJM000422 DZJM000423 DZJM000424 DZJM000425 DZJM000426 DZJM000427 DZJM000429 DZJM000430 DZJM000431 DZJM000432 DZJM000434 DZJM000435 DZJM000442 DZJM000449 DZJM000469 DZJM000475 DZJM000476 DZJM000477 DZJM000486 DZJM000491 DZJM000670 DZJM000672 DZJM000673 DZJM000674 DZJM000675 DZJM000676 DZJM000677 DZJM000678 DZJM000679 DZJM000680 DZJM000681 DZJM000682 DZJM000683 DZJM000684 DZJM000685

Part Name Grid, Charge Wire, Charge Holder, Charge Wire Guide, Lever Plate, Discharge Plate, Lift Plate, Pressure Base, Actuator Snap Ring Sponge, Cap Guide, Inverting Feed Cover, Sub ADF Holder, ADF Stopper, Original Guide, Front ADF Guide, Rear ADF Lever, Release Holder, Separation Roller Gear 2, Pre Feed Bushing Bushing, Torque Limiter Guide, Feed 2 Roller Holder, Sensor C Guide 1, Reversing Joint Adjuster Guide, Inverting 1 Guide, Inverting 2 Guide, Duplex 2 Lever, Duplex 2 Guide Guide, Upper Feed Holder, Stamp Lever, Stopper Plate, Moving Gear Cover, Gear Bracket Holder, Spring T Holder, Spring B Film, ADF Pre Feed Film, Hinge Sleeve, Right Slider Sponge Stopper, Rubber Seal, White Reference Film, Reversing Guide 1 Base, ADF Guide, Lower Paper Feed Guide, Upper Paper Feed Actuator, Timing Actuator, NP Actuator, Original Width Holder, Stamp Lever, Pressure Adjustment Base, Left Hinge Guide, Left Spring Holder, Upper Left Spring Cover, Pad Stopper, ADF Cover Base, Hinge Right Holder, Roller

Ref. No. Remarks 1433 1443 PM 1436 1429 704 1613 2005 2205 S9 1424 2711 2628 2313 2506 2312 2311 2404 2513 2020 2508 2510 PM 2518 2519 2516 2415 2414 2432 2430 2431 2434 2701 2129 2420 2408 2405 2303 2304 2514 2115 2119 2121 2630 2421 2108 2523 1705 2002 2017 2004 2008 1713 1811 For DP-8020E/8020P* 2007 1804 1806 1809 2023 2013 1818 2026

Destination All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All

336 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Alphanumerical Parts List Part Number DZJM000686 DZJM000687 DZJM000688 DZJM000690 DZJM000691 DZJM000692 DZJM000888 DZJM000926 DZJM000927 DZJM001076 DZJM001230 DZJM001241 DZJM001283 DZJM001284 DZJM001285 DZJM001308 DZJM001309 DZJM001311 DZJM001313 DZJM001314 DZJM001315 DZJM001317 DZJM001318 DZJM001319 DZJM001321 DZJM001322 DZJM001324 DZJM001325 DZJM001326 DZJM001327 DZJM001328 DZJM001329 DZJM001330 DZJM001331 DZJM001332 DZJM001333 DZJM001337 DZJM001338 DZJM001339 DZJM001340 DZJM001341 DZJM001342 DZJM001343 DZJM001344 DZJM001345 DZJM001347 DZJM001349 DZJM001357 DZJM001358 DZJM001363 DZJM001366 DZJM001369 DZJM001372 DZJM001373 DZJM001375 DZJM001378 DZJM001381 DZJM001387 DZJM001388 DZJM001402

Part Name Stopper, Original Guide, Rack Guide, Spring Right Holder, Left Spring Rack, Pickup Sheet, White Film, Front Film, Lower Film, Upper Sheet Guide, Lower Feed Spacer Sheet, Guide 2 Guide, Film A Film, Top Cover Film, Bottle Shutter Sheet, Toner Film, Pipe Roller, Spacer Bushing, OPC Slider Frame, Mirror 1 Guide, OPS Guide, Lamp Harness Guide, Paper Tray Guide, Paper Sheet, Splash Prevention Sponge, Cleaning Screw, WT Pipe, WTB Sponge, Long Cleaning Sponge, Short Cleaning Holder, OPC Drum Shaft Cap, WT PDL, WTB Film, PDL Base, Charge Cleaning Base, Pad Lever, Cleaning Pad, Cleaning Handle, Cleaning Lever Sponge, Charge Film, Separation Roller Film, Rear Guide Film, Lower Guide Slider Sheet, Paper Guide Film, Front Guide Sheet, Protection Film, Airflow Control Sheet, Protection Film, Paper Guide Holder, Rear Charge Holder, Charge Film, Charge Side Film, Guide Sheet, Guide Damper Film, Guard Actuator, ADF

Ref. No. 2016 2028 1819 1807 2027 1814 2123 1825 1826 3137 2707 1717 2714 2713 2127 1213 1309 1333 1409 1404 1315 407 114 422 3101 3022 1415 PM 1412 PM 1420 1426 1413 1414 1407 1422 1417 1416 1439 1441 1428 1440 1427 1430 655 636 635 408 3021 637 1828 950 319 1617 1437 1431 1454 666 667 692 668 4303

Remarks

Destination All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All

337 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Alphanumerical Parts List Part Number DZJM001403 DZJM001406 DZJN000052 DZJN000076 DZJN000085 DZJN000086 DZJN000087 DZJN000088 DZJN000093 DZJP000005 DZJP000026 DZJP000063 DZJP000064 DZJP000065 DZKB000641 DZKB000669 DZKB000762 DZKB000796 DZKB000923 DZKB000924 DZKB000927 DZKB000928 DZKB000929 DZKB000929 DZKB000930 DZKB000931 DZKG000107 DZKG000108 DZKG000109 DZKG000110 DZKG000112 DZKG000113 DZKG000114 DZKG000115 DZKG000150 DZKG000151 DZKG000152 DZKG000153 DZKG000154 DZKG000376 DZKG000377 DZKG000378 DZKG000381 DZKG000382 DZKG000383 DZKG000384 DZKG000405 DZKG000416 DZKG000419 DZKG000420 DZKG000422 DZKG000423 DZKG000424 DZKJ000017 DZKK000090 DZKK000119 DZKK000120 DZKK000121 DZKK000122 DZKK000123

Part Name Actuator, OPS Separator Rubber, Separation Gum, Paper Tray Blade, Cleaning Sheet, Toner Dispersion Plate, Rubber Roller, Exit 2 Rubber, CCD Frame Plate, Pad Pressure Felt Felt, Front Cleaning Felt, Rear Cleaning Board, Pad Key, Reset Key, B Key, Stop Key, Start Key, Touch 2 Key, Touch 3 Keys, Numerical Keys, Numerical Keys, Numerical Keys, Numerical Key, Function Key, A Shaft, Pre Feed Roller Shaft, Pinch Roller Shaft, ADF Shaft, Pinch 2 Shaft, Drive Pinch Shaft Shaft 1, Drive Shaft 2, Drive Shaft, Drive Pinch Shaft, Pre Feed Shaft, Left Hinge Paper Feed Shaft Assembly Shaft, Hinge Right Shaft, DR Shaft 1, Idle Shaft 2, Idle Shaft, Drum Drive Shaft, Mag Drive Shaft, Feed Shaft, Pickup Shaft, Reverse Shaft, Separation Roller Pin, Fulcrum Assembly, Arm Shaft Shaft, P8L Shaft, P8S Shaft, P6 Plate, DIAL Stopper, Tray Lever, SA Lever, Interlock Actuator 2 Plate, Front Pressure Actuator, 2nd Paper Feed

Ref. No. 116 1109 2024 948 1408 1301 315 1104 428 1620 2117 1410 1411 684 508 522 507 509 528 527 510 510 510 510 512 521 2316 2623 2310 2712 2703 2603 2614 2615 2014 2019 1803 2029 1817 1345 1320 1322 1537 1533 626 620 633 2507 697 1616 2301 2302 2104 911 743 913 229 1128 1019 3102

Remarks PM PM PM

PM PM

For For For For

DP-8020E/8020P* DP-8020E/8020P* DP-8016P DP-8020E/8020P*

Destination All All All All All All All All All All All All All All All All All All All All PU, PUG Except PF, PU, PUG All PF All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All

338 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Alphanumerical Parts List Part Number DZKK000124 DZKK000126 DZKK000128 DZKK000129 DZKK000130 DZKK000131 DZKL000083 DZKL000084 DZKL000085 DZKL000086 DZKL000087 DZKL000088 DZKM000020 DZKN000006 DZKN000126 DZKN000178 DZKN000181 DZKN000184 DZKN000185 DZKN000186 DZKN000187 DZKN000188 DZKN000207 DZKN000209 DZKN000231 DZKN000266 DZKN000267 DZKN000268 DZKN000269 DZKN000270 DZKN000271 DZKN000272 DZKN000273 DZKN000398 DZKN000401 DZKN000403 DZKN000404 DZKN000405 DZKN000406 DZKN000407 DZKN000408 DZKN000409 DZKN000410 DZKN000412 DZKN000413 DZKN000415 DZKN000416 DZKN000417 DZKN000418 DZKN000420 DZKN000422 DZKP000084 DZKP000200 DZKP000201 DZKP000202 DZKP000203 DZKP000204 DZKP000205 DZKP000206

Part Name Plate, Rear Pressure Latch, Arm Arm, OP Paper Tray Connect Arm, Reverse Arm, Rear Frame Arm, Rear Cover Lever, Paper Exit Sensor Actuator, Registration Sensor Actuator, No Paper Lever, Release Actuator, Paper Tray Actuator, Duplex Paper Sheet, ADF Coil Spring, Idle Gear Spring, Gear Spring, Cap Spring, Timing Roller Spring, Separation Roller Spring, Reversing Guide 1 Spring, Duplex 2 Guide Spring, White Reference Seal Guide Spring Coil Spring, Ground Spring, Latch Spring, Hinge Support Spring, Actuator Spring, Latch Spring, White Front Spring, Upper Left Hinge Spring, Lower Left Hinge Spring, White Rear Spring, Pick Up Spring, Hinge Right Spring, Coil Spring, Joint Spring, Motor Spring, Wire Spring, OPC Drive Spring, Mag Drive Spring, Pressure Spring, Idle ADU Spring, Ground Spring, Contact Spring, Lift Up Spring, Toner Spring, Charge Spring, Reverse Spring, Release Spring, BTR Spring, Fulcrum Spring, Hinge (Silver, i-ADF) Spring, Pinch Roller Plate Spring, Pinch Roller Plate Spring, Pinch 1 Plate Spring, Pinch Roller Plate Spring, Discharge Plate Spring 2, Discharge Holder, Pinch Roller Plate Spring, Ground

Ref. No. Remarks 1018 611 3108 631 719 720 607 608 660 723 123 731 For DP-8020E 2032 2407 2619 1425 708 2512 2412 2433

Destination All All All All All All All All All All All All All All All All All All All All

2107

All

2417 2109 2317 2318 117 1904 1810 1808 1805 1704 2022 1820 1343 1313 314 306 1536 1532 1008 1017 1022 929 3135 1509 1435 686 729 707 664 2320 3020 2629 2710 2503 2708 2625 2424 2425

All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All

For DP-8020E

339 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Alphanumerical Parts List Part Number DZKP000207 DZKP000215 DZKP000225 DZKP000251 DZKP000280 DZKP000358 DZKP000365 DZKP000366 DZKP000367 DZKP000368 DZKP000370 DZKP000371 DZKP000372 DZKP000373 DZKP000374 DZKP000375 DZKP000376 DZKP000377 DZKP000378 DZKP000379 DZKP000380 DZKP000384 DZKP000385 DZKP000388 DZKP000389 DZKQ000012 DZKQ000031 DZKQ000042 DZKQ000051 DZKQ000070 DZKQ000071 DZKQ000073 DZKQ000074 DZKQ000106 DZKQ000107 DZKQ000108 DZKQ000109 DZKQ000110 DZKQ000111 DZKQ000115 DZKQ000116 DZKQ000117 DZKQ000119 DZKQ000120 DZKR000004 DZKR000024 DZKR000032 DZKR000037 DZKR000038 DZLA000080 DZLA000083 DZLA000198 DZLA000204 DZLA000205 DZLA000206 DZLA000211 DZLA000216 DZLA000257 DZLA000258 DZLA000304

Part Name Plate Spring, Drive Plate Spring, ADF Input Tray Plate, Star Wheel Plate, Exit Spring, 2/3 Mirror Spring, Plate Spring, Speaker Spring, PS Spring, PS Cover Spring, Paper Tray Ground Plate, Mirror 1 Spring Plate, Ground Plate, Ground 2 Plate, Idle Spring Spring, LAN Ground Spring Lead, HV Bias Transfer Lead, Pinch Roller Timing Lead, Plate Discharge Bracket, Pinch Roller Lead, BTR Frame Plate 2, Ground Plate 1, Ground Spring, Ground Plate, Ground Spring, Actuator Spring, Torque Limiter Spring, Introduction Spring, B1 Sensor Spring, Timing Spring, Original Length Spring, Ground Spring, NP Actuator Spring, Return Spring, Pickup Spring, Actuator Spring, Opening Spring, Latch Spring, Registration Sensor Spring, OP Drive Spring, Front Spring, Rear Spring, DC Spring, Actuator Spring, Pressure Plate Spring, Sensor B2 Spring, Ground Spring, Pinch Roller Pressure Spring, Tray Hold Up Roller 1, Pinch Roller, Idle Roller, Paper Tray Roller, Pre Feed Roller, ADF Roller, Separation Roller 2, Pinch Roller, Paper Feed Roller, Feed Roller, Exit 1 Roller, Drive Pinch

Ref. No. 2704 2111 1450 2011 420 2128 513 922 920 935 409 1005 1024 1002 812 662 713 715 714 727 932 1504 517 3024 1451 2204 2511 2319 2631 2003 1716 1919 2009 3103 625 1107 1011 614 609 3109 656 657 206 730 2006 2524 1707 2031 121 2130 1003 3016 2018 2314 2509 2624 2001 2010 1812 2015

Remarks

For DP-8020E

PM

For DP-8020E

PM PM PM PM

Destination All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All

340 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Alphanumerical Parts List Part Number DZLA000326 DZLA000356 DZLA000357 DZLA000358 DZLA000359 DZLA000360 DZLA000362 DZLA000363 DZLA000365 DZLA000366 DZLA000367 DZLA000368 DZLA000369 DZLA000370 DZLA000371 DZLA000381 DZLA000382 DZLA000383 DZLA000384 DZLA000415 DZLA000418 DZLB000013 DZLB000022 DZLB000060 DZLC000001 DZLD000024 DZLF000008 DZLF000015 DZLF000028 DZLF000036 DZLF000077 DZLF000172 DZLF000191 DZLF000199 DZLF000208 DZLF000283 DZLF000315 DZLF000327 DZLF000329 DZLF000330 DZLF000331 DZLF000332 DZLF000333 DZLF000334 DZLF000335 DZLF000342 DZLF000354 DZLF000382 DZLF000385 DZLF000452 DZLF000453 DZLF000454 DZLF000456 DZLF000465 DZLF000697 DZLF000698 DZLF000699 DZLF000700 DZLF000701 DZLF000702

Part Name Roller, Exit Pinch Roller, Paper Tray Roller, Idle 2 Roller, ADU Roller, Intermediate Roller, Feed Roller, Pressure Roller, Pickup Roller, Separation Roller, Reverse Roller, Pinch Timing Roller, Bias Transfer Roller, Duplex Pinch Roller, Duplex Feed Roller, Registration Roller, Feed 2 Roller, Exit 3 Roller, Inverting Feed Roller, Drive Roller, Feed Roller, Fuser Pulley Pulley, Scanner Pulley, 19 Duplex Pulley, Idler Drum, Wire Gear, D16 Gear, B44 Gear, E14E25 Gear, E25 F Gear, D14 Gear, B42E27 Gear, D24E18 Gear, E39 Fuser Roller Gear, Guide Gear, E29 F Gear, E16 Gear, B18 Gear, ADF Gear 1, Pre Feed Gear, E26S35 Drive Gear, E18 Drive Gear, E21E27 Gear, E21 Drive Gear, D24E18 Gear, E20 Gear, E25 Gear, E18 F Gear, D16 Pulley, S27 F Gear, E20S20 F Gear, E28S22 D Gear, D26 Gear, Tray Gear, Pipe 15 Gear, Pipe 15T Gear, Screw 1 Gear, Screw 2 Coupling 1 Gear, Idle

Ref. No. 2012 1609 1009 1016 3104 623 1021 619 658 629 712 711 728 735 601 2517 2515 2428 2706 689 1115 2611 312 736 308 302 2608 2406 2309 2308 1710 2410 2609 1112 125 2605 1909 2419 2315 2021 2604 2423 2606 2616 2607 741 740 2307 2030 1910 1907 1908 2025 1611 1341 1346 1327 1330 1317 1319

Remarks

For DP-8020E PM PM PM PM PM PM For DP-8020E For DP-8020E

PM PM

For DP-8020E

For DP-8020E For DP-8020E

Destination All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All

341 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Alphanumerical Parts List Part Number DZLF000703 DZLF000705 DZLF000706 DZLF000707 DZLF000708 DZLF000709 DZLF000710 DZLF000711 DZLF000713 DZLF000714 DZLF000715 DZLF000716 DZLF000717 DZLF000718 DZLF000719 DZLF000720 DZLF000721 DZLF000722 DZLF000723 DZLF000724 DZLF000726 DZLF000731 DZLF000732 DZLF000733 DZLF000734 DZLF000735 DZLF000736 DZLF000737 DZLF000738 DZLF000739 DZLF000740 DZLF000741 DZLF000742 DZLF000743 DZLF000745 DZLF000746 DZLF000747 DZLF000748 DZLG000035 DZLK000013 DZLK000023 DZLK000029 DZLK000031 DZLK000043 DZLK000044 DZLL000005 DZLM000006 DZLM000007 DZLM000046 DZLM000050 DZLM000052 DZLM000072 DZLM000132 DZLM000133 DZLM000134 DZLM000157 DZLM000194 DZLM000203 DZLM000204 DZLM000205

Part Name Gear 2, Idle Knob, JAM Release Gear, Exit Roll Gear 2, Drum Gear 1, Drum Gear 1, Mag Gear, Pickup Drive Gear, Pickup Idler Gear 3, Drum Gear 2, Mag Gear 3, MG Gear, Fuser Drive Gear 2, Fuser Idle Gear, Waste Toner Drive Gear 2, Waste Toner Idle Gear 1, Registration Idle Gear 3, Fuser Idle Gear 4, Fuser Idle Gear 2, Registration Idle Gear 1, Waste Toner Idle Gear 1, Exit Idle Gear, PDL Joint Gear, Lift Up 2 Gear, Lift Up Coupling Gear 1, Lift Up Gear, Toner Drive Gear, Toner Sensor Gear 1, Toner Idle Gear 2, Toner Idle Gear 3, Toner Idle Gear 1, OP Paper Tray Idle Gear 3, OP Paper Tray Idle Gear 1, 3rd OP Drive Gear 2, 3rd OP Drive Gear, BTR 27 Gear, 17 Pinch Timing Roller Gear, 15 Duplex Gear, 18 Timing Roller Clutch, One-way Belt 2, Timing Belt, Drive 2 Belt, Drive 1 Belt, Timing T1 Belt 1, Timing Belt, Synchro Wheel, Star Bushing 2, P6L5 Bushing, P6L7.4 Bushing, P6 Bushing, P6L8 Bushing, P6L5 Conductor Bushing, P6L8 Bushing, Pressure Roller Bushing, Bias Transfer Bushing, Rear Bearing, Screw Bearing, Paddle Bushing 2, Joint Bushing, Joint Bearing, PL Screw

Ref. No. 1321 1013 1102 1529 1538 1534 624 621 1528 1530 1524 1517 1522 1519 1521 1526 1523 1525 1527 1520 3110 1419 3136 3120 3123 1508 1505 1507 1510 1506 3106 3111 3303 3302 706 710 738 602 622 2612 1912 1911 737 1513 318 1402 603 2122 2422 642 1103 1813 1020 709 734 1323 1328 1342 1340 1336

Remarks

For DP-8020E

For DP-8020E

PM For DP-8020E

Destination All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All

342 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Alphanumerical Parts List Part Number DZLM000207 DZLM000208 DZLM000209 DZLM000210 DZLM000211 DZLM000212 DZLM000213 DZLM000214 DZLM000215 DZLM000216 DZLM000217 DZLN000007 DZLN000022 DZMA002329 DZMA002333 DZMA002335 DZMA002337 DZMA002339 DZMA002341 DZMA002343 DZMA002348 DZMA002394 DZMA002474 DZMA003291 DZMA003293 DZMA003295 DZMA004338 DZMA004339 DZMA004372 DZMA004431 DZMA004432 DZMA004440 DZMA004441 DZMA004443 DZMA004445 DZMA004447 DZMA004449 DZMA004450 DZMA004451 DZMA004452 DZMA004453 DZMA004454 DZMA004500 DZMA004817 DZMA004818 DZMB000024 DZMB000025 DZMB000026 DZMC000713 DZMC000821 DZMC000822 DZMC000823 DZMC000824 DZMC000825 DZMC000827 DZMC000828 DZMC000829 DZMG000018 DZMG000038 DZMG000041

Part Name Bearing, Mag Bushing, Fuser Roller Bearing 1 Bearing 2 Bushing, Screw Bushing, Left Bushing Bushing Collar, Timing Roller Bearing 3 Bearing 4 Joint, OPC Coupling, Mag Cover, ADF Base, ADF Cover, ADF Front Cover, ADF Rear Cover, ADF Exit Tray, ADF Input Cover, ADF Tray Bottom Rack, Original Guide Cover, Platen Tray, ADF Input Cover, ADF Front Cover, ADF Rear Cover, ADF Guide, Original Front Guide, Original Rear Cover 2, Hinge Cover, Right Paper Tray Cover, Rear Paper Tray Cover, Connector Cover, Left Scanner Cover, Rear Scanner Cover, Right Scanner Cover 1, Front Cover, Right Cover, Left Front Cover, Rear Side Cover, Inner Cover, Exit Cover, Rear Cover, F Card Cover, Front Door Cover, Front Door Bracket, Rear Lower Right Bracket, Rear Lower Left Cover, Jam Access Cover, Hinge Plate, Base Frame, Front Bracket, Center Bracket, Right Handle Guard, Fan Cover, Sub Tray Cover, Sub Tray Latch Latch, Waste Toner Box Catcher, Magnet

Ref. No. 1348 1114 1546 1547 1418 651 618 317 604 1548 1549 1535 1531 2126 2110 2210 2101 2429 2201 2208 2207 103 2201 1702 1701 1902 2203 2202 2131 3002 3004 203 101 102 132 211 216 215 218 219 202 220 217 201 201 3007 3008 3015 2113 931 910 906 803 806 826 1601 1601 2323 214 3018

Remarks PM

For DP-8020E/8020P* For DP-8016P

For Other Paper Tray For 1st Paper Tray

Destination All All All All All All All All All All All All All All All All All All PU,PUG All All All Other All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All

343 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Alphanumerical Parts List Part Number DZMH000013 DZMH000029 DZML000422 DZML000432 DZML000433 DZML000478 DZML000479 DZML000480 DZML000481 DZML000482 DZML000483 DZML000484 DZML000487 DZML000488 DZML000489 DZML000490 DZML000491 DZML000499 DZML000500 DZML000504 DZML000507 DZML000508

Part Name Hinge, Platen Blade, Doctor Tray, Original Lower Tray, Original Upper Tray, Original Upper Tray, Spill Base, Paper Tray Cover, Paper Tray Guide, Front Guide, Rear Plate, Bottom Lever, Guide Cover, Paper Tray Tray, Bypass Cover, Bypass Tray Tray, Sub Bypass Tray, Sub Bypass 2 Guide, Original Front Guide, Original Rear Tray, Original Upper Tray, Original Front Tray, Sub

Ref. No. Remarks 105 1304 1706 1712 1712 1202 1603 1602 For 1st Paper Tray 1605 1606 1610 1604 1602 For Other Paper Tray 126 120 124 122 1711 1714 1712 1708 2209

DZMM000038

Foot, Damping

939

DZNA001040 DZNA001042 DZNA001044 DZNA001046 DZNA001047 DZNA001048 DZNA001049 DZNA001051 DZNA001053

Lamp, Active Key Holder, LCD Key, Copy Key, Fax/E-mail Key, Scan/File Key, Print Cover, Harness Protection Sheet, Keyboard Base

515 506 520 523 524 525 526 518 532

DZNA001055

Sheet, Keyboard

531

DZNA001058

Sheet, Keyboard

531

DZNA001059

Sheet, Keyboard

531

DZNA001153 DZNA001154 DZNA001155 DZNA001156 DZNA001157 DZNA001158 DZNA001159 DZNA001160 DZNA001161 DZNA001162 DZNA001163 DZNA001164 DZNE000117 DZNE000129 DZNE000132 DZNK002411 DZNK003248 DZNK004580 DZNK004940 DZNK004942 DZNK005265

Window, Panel Window, Panel Window, Panel Window, Panel Window, Panel Window, Panel Window, Panel Window, Panel Window, Panel Window, Panel Window, Panel Window, Panel Film, Paper Approach Guide Sheet, Harness Spacer Label, Ground Warning Label, Class A Label, Energy Label, Paper Tray Label, Paper Tray Label, High Temperature

501 501 501 501 501 501 501 501 501 501 501 501 1307 135 670 235 236 234 3416 3416 1026

For DP-8020E/8020P* For DP-8020E/8020P* For DP-8020E/8020P* For DP-8020E/8020P*

For DP-8020E/8020P* For DP-8020E/8020P* (English) For DP-8020E/8020P* (French) For DP-8020E/8020P* (German) For DP-8020P* For DP-8020E For DP-8016P For DP-8020P* For DP-8020E For DP-8016P For DP-8020P* For DP-8020E For DP-8016P For DP-8020P* For DP-8020E For DP-8016P

Destination All All All PU,PUG Other All All All All All All All All All All All All All All PK All All Except PU, PT, PUG, PK All All All All All All All All All All All All PU,PUG,Other PU,PUG,Other PU,PUG,Other PK PK PK PF PF PF PT PT PT All All All PB, PS PK PB PU, PUG PK Except PU, PUG All

344 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Alphanumerical Parts List Part Number DZNK005266 DZNK005268 DZNK005269 DZNK005270 DZNK005283 DZNK005284 DZNK005316 DZNK005416 DZNK005417 DZNK005420 DZNK005449 DZNK005454 DZNK005455 DZNM000005 DZPA000064 DZPA000075 DZPA000086 DZPA000089

Part Name Label, Bypass Tray Label, Laser Caution Label, Toner Bottle Label, Toner Bottle Exchange Label, Heater Main Label, Switch Label, Bypass Tray Label, Paper Size Label, Paper Size Label, Paper Size Label, Laser Caution Label, TEL Label, LINE Logo, Panasonic Screw, Thumb Screw, Drum Unit Fix Screw Screw

DZPA000091

Screw

DZPA000092 DZPA000093 DZPA000097 DZPB000007 DZPB000020 DZPG000001 DZPJ000004 DZPK000017 DZPK000032

Screw Screw Screw Screw, Silver Screw Pin Ring Washer Polyslider

938 827 232 B1 C2 2327 1113 2326 1550

DZQE000003

Rosette

3906

DZQE000005

Rosette Hook and Loop Fastener Tape (Loop Side) Tape, Block Box, Carton Box Box, Carton Box, Carton Cushion, HD Box, Carton Box, Carton Box, Carton Box, Carton Box, Carton Box, Carton Box, Carton Box, Carton Box, Carton Sheet, Cushion Assembly, Cushion Cushion, Top Cushion, Bottom Operating Instructions Operating Instructions Quick Guide Quick Guide Quick Guide Installation Instructions Installation Instructions

3906

Destination Other PU, PUG, Other All All PU, PUG, Other All PU, PUG Other PU, PUG PK PK, PT All All All All All All All Except PU, PT, PUG, PK All All All All All All All All All YCR, YGR, YSR, YVR, YAR, YYR APR

1823

All

1351 4601 3501 4102 3902 4101 4004 4501 4501 4501 4501 4501 4501 4501 4501 4406 4502 4002 4003 3803 3803 3802 3802 3802 4404 4306

All All All All All All All PU,PUG Other PU, PUG Other PU,PUG Other PU, PUG Other All All All All YVR AER AUR, YYR Other YPR, YRR All All

DZQJ000022 DZQJ000083 DZRB000101 DZRB000143 DZRB000580 DZRB000733 DZRB000750 DZRB001070 DZRB001139 DZRB001140 DZRB001141 DZRB001142 DZRB001143 DZRB001144 DZRB001145 DZRB001146 DZRH000479 DZRH000601 DZRH000621 DZRH000622 DZSD002217 DZSD002219 DZSD002231 DZSD002232 DZSD002234 DZSM000523 DZSM000551

A A A A B B B B

Ref. No. 127 209 210 204 224 225 127 4505 4505 4505 209 3904 3905 539 M2 1421 S6 X2

Remarks

937

For For For For For For For For

3rd Paper Tray 3rd Paper Tray 2nd/4th Paper Tray 2nd/4th Paper Tray 3rd Paper Tray 3rd Paper Tray 2nd/4th Paper Tray 2nd/4th Paper Tray

345 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Alphanumerical Parts List Part Number DZSM000741 DZSM000756 DZSM000811 DZSM000812 DZSM000813 DZSM000815 DZSM000818 DZSM000820 DZSM000825 DZTC000052 DZTC000053 DZTD000004 DZTE000025 DZTE000052 DZTK000002 DZTT000614 DZTT000711 DZTT000718 DZTY000311 DZTY000312 DZTY000314 DZTY000315 DZTY000316 DZTY000317 DZTY000357 DZUF000008 DZUF000009 DZUF000010 DZUJ000017 DZUJ000019 DZUJ000021 DZUJ000023 ETXDN478AAEA

Part Name Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Mirror 1 Mirror 2 Sheet, Reflective Glass, Platen (L) Glass, Scanning (S) Counter Pin 1 Box, Carton Pin 2 Assembly, Main Drive Assembly, Bottle Drive Assembly, Feed Drive Assembly, Exit Drive A Assembly, Exit Drive B Assembly, Exit Drive A Assembly, Lift Up Drive Screw, Supply Screw 1 Screw 2 Cleaner, Bottle Shutter Seal, Frame Seal, Pipe Packing, Inner Cover PC Board, PS

Ref. No. Remarks 4202 3503 4504 4103 3901 4001 4602 4701 4801 415 421 411 106 110 821 1551 4802 1552 1540 1539 1541 1542 For DP-8020P*/8016P 1543 For DP-8020E 1542 For DP-8020E 3132 1337 1329 1331 1209 1308 1334 233 2901

ETXDN478EAEA

PC Board, PS

2901

ETXDN478EAEC FFPCP0034 FFPFJ0033B FFPFJ0039B FFPFJ0041B FFPFJ0043B FFPFJ00441 FFPHQ0063 FFPKD07791 FFPLK0381B FFPLN0005 FFPLP0769C FFPMF10281 FFPMF1029 FFPMF1031B FFPMQ0536 FFPMQ0648 FFPMQ0649 FFPMV0001 FFPTE1621B FFPTE2259 FFPTE2719

PC Board, PS Heater Snap Ring Snap Ring Snap Ring Snap Ring Ring, Stopper Coupling 2 Bracket, Heater Latch Spring Spring, Terminal Gear 2, Lift Up Gear 3, Lift Up Gear, Worm Bushing, 8 Metal Bushing, Front Bushing Polyslider Washer Label, HV Caution Label, HV Label, F-ROM

2901 424 S9 G6 H7 K9 3119 3118 936 1903 1127 716 3121 3122 3125 3105 733 698 1558 830 426 223

G0A173J00001

Coil 1

819

G0A352H00002

Coil 2

820

For DP-8020E

For DP-8020E/8020P*

Destination All Europe only All All All All All All All All All All All All PB, PF, PM, PP, PS All All All All All All All All All All All All All All All All All PU, PUG, PT Except PU, PUG, PT, PK PK All All All All All All All All All All All All All All All All All All All All All Except PU, PT, PK, PUG Except PU, PT, PUG

346 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Alphanumerical Parts List Part Number K0AHLE000003 K0BDB0000080 K2CH3DH00002 K2CK3DH00027 K2CM3DH00013 K2CT3DH00023 K2ME4B000001 K5X216BG0002 L2BA00000007 L2DA00000126 L6FALEGK0018 L6HBHHGC0011 L6HBJJGB0001 L9AAAABA0002 L9AAABFB0001 L9AAAEGB0006 L9AABCEZ0001 L9EAAJ000020 L9EAAJ000021 L9EAAJ000022 L9EAAK000009 L9EAAK000010

Part Name Switch, Interlock Thermostat Cord, AC Power Cord, AC Power Cord, AC Power Cord, AC Power Plug, PTT Fuse, Thermal PC Board, HSU Sensor, Toner Fan, Rear Motor, ADF Motor, ADF Solenoid, Stamp Solenoid Solenoid Solenoid Clutch Clutch Clutch Clutch, Micro 2 Clutch, Micro 1

LPA3612F-BR

LSU Unit

LPA3612F-R M0CE00000028 MGG03204Z03 PFJA04B006Y PFJA05B001Y PFJA05B001Y PJBAC0044Z PJBCB0016Z PJBCB0018Z-1 PJBLC0026Z PJBUC0091Z PJBUC0105Z PJBVC0149Z PJBVC0150Z PJBVC0151Z PJCGC0003Z PJDGC0170Z PJDGC0186Z PJDHC0019Z PJDIC0011Z PJGFC0033Z PJGFC1214Z PJGTC0053Z PJHEC0124Z

LSU Unit HDD Unit LCD Module Cord, Line Cord, Line Plug, PTT Case, Clutch Key, Contrast Key, Zoom Arm Plate, Exit Plate, Ground Drive Spring, Clutch Spring, Arm Spring Solenoid, Damper Gear 2, Screw 2 Gear, Feed Cam, Feed Joint, Screw Label, Bypass Tray Label, EPA Label, Heater Main Pad, Scanning

PJHSC0025Z

Gasket

PJJWC0009Z PJJWC0010Z PJJWC0011Z PJJXC0042Z

Cord, Line Cord, Line Cord, Line Firmware CD CD (For Operating Instructions) Software CD Software CD Software CD Software CD

PJJXC0228Z PJJXC0230Z PJJXC0232Z PJJXC0234Z PJJXC0257Z

Ref. No. Remarks 227 1120 For DP-8020E/8020P* 3406 3406 3406 3406 3907 1118 817 1349 815 For DP-8020E/8020P* 1905 2601 1824 For DP-8020E/8020P* 1545 2403 2411 2324 2632 2325 694 695

3903 3903 3903 3804

Destination All All PU, PUG, PT PK PF, PM, PP, PS PB,PY AMR All All All All All All All All All All All All All All All Except PU, PUG, PK, PT PU, PUG, PK, PT All All ENR ARR, AVR AVR All All All All All All All All All All All All All All PK, PT All PK All PA, PB, PF, PM, PP, PS, PY ABR, AKR, AWR AGR AMR All

3408

Except PK, PT

3407 3407 3407 3502

PU, PUG Except PU, PUG, PK PK PU, PUG

829 829 804 519 3903 3903 3907 640 516 511 1560 2034 953 641 1559 685 1561 1324 639 682 1344 127 212 224 104 952

347 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Alphanumerical Parts List Part Number PJJXC0259Z PJJXC0261Z PJJXC0263Z PJJXC0265Z PJJXC0267Z PJPAC0004Z PJPAC0005Z PJPAC0011Z PJPGC0327Z PJPGC0328Z PJPGC0371Z PJPGC0681Z PJPGC0682Z PJPGC0683Z PJPGC0684Z PJPGC0685Z PJPGC0686Z PJPGC0687Z PJPGC0688Z PJPGC0689Z PJPGC0690Z PJPGC0691Z PJPGC0723Z PJPGC0724Z PJPGC0725Z PJPQC0038Z PJPQC0039Z PJQHC0189Z PJQMC0700Z PJQMC0713Z PJQQC0065Z PJQQC0066Z PJQQC0069Z PJQQC0070Z PJQRC0008Z PJQRC0025Z PJQRC0172Z PJQRC0182Z PJQRC0183Z PJRCC0004Z PJRCC0005Z PJSCC0015Z PJSDC0005Z PJUAC0215Y PJUIC0218Z PJUIC0219Z PJUIC0221Z PJUIC0254Z PJUIC0310Z PJURC0055Z PJUSC0077Z PJVZF2121PB PJWPF2740AZ PJWQF2120PB PJWQF2121PB PJYCF2120PB0 PJYCF2120PK0 PJYCF2120PU0

Part Name Software CD Software CD Software CD Software CD Software CD Pad, Top Palette, Wooden Palette, Wooden Box, Bottom Pad Box, Bottom Box Box Box Angle, L Box, Bottom Box Box Box Box Box Box Box Box Box Process, Cushion R Process, Cushion L Notice Operating Instructions Operating Instruction Quick Guide Quick Guide Quick Guide Quick Guide Important Notice Important Notice Installation Instructions Installation Instructions Installation Instructions Label, Sensor Label 3, Sensor Brush, Antistatic Drive, Ground Spring Frame, OPC Base, Key Counter Cover, Key Counter Cover, Key Counter Front Bracket, ADF Mounting Bracket, Solenoid Pipe, Support Spacer, Feed Guide Bias Transfer Assy PC Board, RLB Assembly, Lift Motor Assembly, Bottle Motor Assembly, Cushion Assembly, Cushion Assembly, Cushion

PJYPF3180PB

Assembly, Control Panel

Ref. No. 3502 3502 3603 3603 3603 3402 3414 3414 3413 3412 3413 3405 3405 3405 3419 3413 3405 3405 3405 3405 3405 3405 3405 3405 3405 3420 3421 3908 3418 3418 3410 3410 3410 3410 3417 3417 3409 3504 3601 1619 136 1028 1557 1442 237 238 239 2112 1554 1338 653 748 2804 3138 1503 3411 3411 3411 538

Remarks

For DP-8020E For DP-8020E For DP-8020E

For For For For For For For For For

DP-8020P* DP-8020P* DP-8020P* DP-8016P DP-8016P DP-8016P DP-8020E DP-8020P* DP-8016P

For DP-8020E

Destination Other PK PU, PUG Other PK PK PK PU, PUG Except PU, PUG, Except PK PU, PUG Except PU, PUG, PU PK PK PK Except PU, PUG, PU PK Except PU, PUG, PU PK PUG PUG PUG All All All PK PT PU, PUG PA, PB, PF, PM, PP PY Except PK PK All All All All All All All All All All All All All All All All All All All Except PU, PUG, PK PU, PUG PA, PB, PM, PP, PS, PY

PK

PK

PK

PK

PS

PK

348 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Alphanumerical Parts List Part Number PJYPF3180PF PJYPF3180PK PJYPF3180PT PJYPF3180PU

Assembly, Assembly, Assembly, Assembly,

Part Name Control Panel Control Panel Control Panel Control Panel

PJYPF3181PB

Assembly, Control Panel

538

For DP-8020P*

PJYPF3181PF PJYPF3181PK PJYPF3181PT PJYPF3181PU PJYPF3182PF PJYPF3182PK PJYPF3182PT

Assembly, Assembly, Assembly, Assembly, Assembly, Assembly, Assembly,

Panel Panel Panel Panel Panel Panel Panel

538 538 538 538 538 538 538

For For For For For For For

PJYPF3182PU

Assembly, Control Panel

538

For DP-8016P

PJZEF21200PU PJZEF2121PU PJZFF3180PB PJZNF3100PK PJZSF2121PB2 PJZSF2121PU2 PJZSF3180PB PJZSF3180PU PJZYF212500 PJZYF212CAZ PJZYF212D00 PJZYF212E00 PJZYF212F00 PJZYF3184PK PJZYF3184PU SPM-3 XNC3FJ XPJ2D14WV XSB4+10FJ XSN3+W10FJ XSN4+W10FN XTB3+10GFJ XTB3+12GFJ XTB3+12JFJ XTB3+20GFJ XTB3+32GFJ XTB3+6FFJ-RP XTB3+6JFJ XTB3+8FFJ XTB3+8GFJ XTB3+8GFN XTB3+8JFI XTB3+8JFJ XTB4+8JFJ XTN3+10GFJ XTW3+10SFJ XTW3+6LFJ XTW3+6LFJR XTW3+8PFJ XUC3VM XUC4VM XUC5VM XUC6VM XUC7VM XYN26+F4FJ

Scanning Pad Ground Spring Kit Assembly, Feed Roller Shaft CCD Unit Fuser Unit Fuser Unit Fuser Unit Fuser Unit Bushing Screw Assy Assembly, Cleaning Pad Assembly, Charge Corona Assembly, Process Unit Assembly, OPC Frame Hopper Unit Hopper Unit Spacer Nut Pin 3 Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw E-Ring E-Ring E-Ring E-Ring E-Ring Screw

1822 1556 696 427 1027 1027 1027 1027 1360 1455 1447 1449 1448 1217 1217 1544 Y7 1553 Y11 Y5 F7 X1 6A W9 X4 Y4 Y2 62 X9 X8 Q8 B4 X6 1N Y8 E8 Y3 Y6 Y1 J6 J7 K5 5Z J8 1562

Control Control Control Control Control Control Control

Ref. No. 538 538 538 538

For For For For

For For For For

Remarks DP-8020E DP-8020E DP-8020E DP-8020E

DP-8020P* DP-8020P* DP-8020P* DP-8020P* DP-8016P DP-8016P DP-8016P

DP-8016P DP-8016P DP-8020E/8020P* DP-8020E/8020P*

Destination PF PK PT PU, PUG PA, PB, PM, PP, PS, PY PF PK PT PU, PUG PF PK PT PU, PUG, PA, PB, PM, PP, PS, PY All All All All Except PU, PUG, PT PU, PUG, PT Except PU, PUG, PT PU, PUG, PT All All All All All PK PU, PUG All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All

349 Ver. 1.0

OCT 2006

DP-8020E/8020P/8016P

Alphanumerical Parts List Part Number XYN3+F14FJ XYN3+F4FJ XYN3+F5FJ XYN3+F6FJ XYN3+F8FJ XYN4+F6FJ XYN4+F8FJ

Part Name Screw Screw Screw Screw Screw Screw Screw

Ref. No. X7 5M 3F 18 X3 Y10 Y9

Remarks

Destination All All All All All All All

350 Ver. 1.0

OCT 2006

E