PAN-ACE7.0-100%-Pass

April 13, 2017 | Author: Robert Martin | Category: N/A
Share Embed Donate


Short Description

Download PAN-ACE7.0-100%-Pass...

Description

Realize Your Potential: paloaltonetworks

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?lo...

Test - Accredited Configuration Engineer (ACE) Exam - PAN-OS 7.0 Version ACE Exam

Question 1 of 50. Which link is used by an Active/Passive cluster to synchronize session information? The Data Link The Control Link The Uplink The Management Link Mark for follow up

Question 2 of 50. Select the implicit rules that are applied to traffic that fails to match any administrator-defined Security Policies. (Choose all rules that are correct.) Intra-zone traffic is allowed Inter-zone traffic is denied Intra-zone traffic is denied Inter-zone traffic is allowed

Mark for follow up

Question 3 of 50. In a Destination NAT configuration, the Translated Address field may be populated with either an IP address or an Address Object. True

False

Mark for follow up

Question 4 of 50. Which of the following is NOT a valid option for built-in CLI Admin roles? deviceadmin devicereader superuser read/write Mark for follow up

Question 5 of 50.

Taking into account only the information in the screenshot above, answer the following question. An administrator is pinging 4.4.4.4 and fails to receive a response. What is the most likely reason for the lack of response? There is a Security Policy that prevents ping. There is no route back to the machine originating the ping. There is no Management Profile. The interface is down.

1 of 9

7/12/16, 5:22 PM

Realize Your Potential: paloaltonetworks

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?lo...

Mark for follow up

Question 6 of 50. As the Palo Alto Networks Administrator responsible for User-ID, you need to enable mapping of network users that do not sign-in using LDAP. Which information source would allow for reliable User-ID mapping while requiring the least effort to configure? WMI Query Captive Portal Active Directory Security Logs Exchange CAS Security logs Mark for follow up

Question 7 of 50. As the Palo Alto Networks Administrator you have enabled Application Block pages. Afterwards, not knowing they are attempting to access a blocked web-based application, users call the Help Desk to complain about network connectivity issues. What is the cause of the increased number of help desk calls? The File Blocking Block Page was disabled. Some App-ID's are set with a Session Timeout value that is too low. Application Block Pages will only be displayed when Captive Portal is configured. The firewall admin did not create a custom response page to notify potential users that their attempt to access the web-based application is being blocked due to company policy. Mark for follow up

Question 8 of 50. The following can be configured as a next hop in a static route: Virtual Systems Virtual Switch Virtual Router A Policy-Based Forwarding Rule Mark for follow up

Question 9 of 50. The "Drive-By Download" protection feature, under File Blocking profiles in Content-ID, provides: Increased speed on downloads of file types that are explicitly enabled. Password-protected access to specific file downloads for authorized users. Protection against unwanted downloads by showing the user a response page indicating that a file is going to be downloaded. The ability to use Authentication Profiles, in order to protect against unwanted downloads. Mark for follow up

Question 10 of 50. What is the maximum file size of .EXE files uploaded from the firewall to WildFire? Always 10 megabytes. Always 2 megabytes. Configurable up to 10 megabytes. Configurable up to 2 megabytes. Mark for follow up

Question 11 of 50. Security policy rules specify a source interface and a destination interface. True

False

Mark for follow up

Question 12 of 50.

2 of 9

7/12/16, 5:22 PM

Realize Your Potential: paloaltonetworks

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?lo...

Considering the information in the screenshot above, what is the order of evaluation for this URL Filtering Profile? Allow List, Block List, Custom Categories, URL Categories (BrightCloud or PAN-DB). URL Categories (BrightCloud or PAN-DB), Custom Categories, Block List, Allow List. Block List, Allow List, Custom Categories, URL Categories (BrightCloud or PAN-DB). Block List, Allow List, URL Categories (BrightCloud or PAN-DB), Custom Categories. Mark for follow up

Question 13 of 50. In a Palo Alto Networks firewall, every interface in use must be assigned to a zone in order to process traffic. True

False

Mark for follow up

Question 14 of 50. All of the interfaces on a Palo Alto Networks device must be of the same interface type. True

False

Mark for follow up

Question 15 of 50. Color-coded tags can be used on all of the items listed below EXCEPT: Zones Vulnerability Profiles Address Objects Service Groups Mark for follow up

Question 16 of 50. How do you reduce the amount of information recorded in the URL Content Filtering Logs? Enable "Log container page only". Disable URL packet captures. Enable URL log caching. Enable DSRI. Mark for follow up

Question 17 of 50.

3 of 9

7/12/16, 5:22 PM

Realize Your Potential: paloaltonetworks

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?lo...

Which type of license is required to perform Decryption Port Mirroring? A subscription-based SSL Port license A free PAN-PA-Decrypt license A Client Decryption license A subscription-based PAN-PA-Decrypt license Mark for follow up

Question 18 of 50. Traffic going to a public IP address is being translated by a Palo Alto Networks firewall to an internal server’s private IP address. Which IP address should the Security Policy use as the "Destination IP" in order to allow traffic to the server? The server’s private IP The firewall’s gateway IP The server’s public IP The firewall’s MGT IP Mark for follow up

Question 19 of 50. Which of the following must be enabled in order for User-ID to function? Security Policies must have the User-ID option enabled. Captive Portal must be enabled. User-ID must be enabled for the source zone of the traffic that is to be identified. Captive Portal Policies must be enabled. Mark for follow up

Question 20 of 50. Which of the following can provide information to a Palo Alto Networks firewall for the purposes of User-ID? (Select all correct answers.) RIPv2 Domain Controller Network Access Control (NAC) device SSL Certificates

Mark for follow up

Question 21 of 50. You can assign an IP address to an interface in Virtual Wire mode. True

False

Mark for follow up

Question 22 of 50.

Taking into account only the information in the screenshot above, answer the following question. An administrator is using SSH on port 3333 and BitTorrent on port 7777. Which statements are True? The SSH traffic will be allowed. The SSH traffic will be denied. The BitTorrent traffic will be allowed. The BitTorrent traffic will be denied.

4 of 9

7/12/16, 5:22 PM

Realize Your Potential: paloaltonetworks

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?lo...

Mark for follow up

Question 23 of 50. An interface in Virtual Wire mode must be assigned an IP address. True

False

Mark for follow up

Question 24 of 50. Using the API in PAN-OS 6.1, WildFire subscribers can upload up to how many samples per day? 10 50 500 1000 Mark for follow up

Question 25 of 50. WildFire analyzes files to determine whether or not they are malicious. When doing so, WildFire will classify the file with an official verdict. This verdict is known as the WildFire Analysis verdict. Choose the three correct classifications as a result of this analysis and classification? Malware detection Spyware Grayware Adware Safeware Benign

Mark for follow up

Question 26 of 50. Choose the best answer: In PAN-OS, the WildFire Subscription Service allows updates for malware signatures to be distributed as often as… Once an hour Once a day Once a week Once every 15 minutes Mark for follow up

Question 27 of 50. In order to route traffic between Layer 3 interfaces on the Palo Alto Networks firewall, you need a: Virtual Router VLAN Virtual Wire Security Profile Mark for follow up

Question 28 of 50. Which of the following platforms supports the Decryption Port Mirror function? PA-3000 VM-Series 100 PA-2000 PA-4000 Mark for follow up

Question 29 of 50.

5 of 9

7/12/16, 5:22 PM

Realize Your Potential: paloaltonetworks

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?lo...

When configuring a Decryption Policy rule, which option allows a firewall administrator to control SSHv2 tunneling in policies by specifying the SSH-tunnel App-ID? SSH Proxy SSL Forward Proxy SSL Inbound Inspection SSL Reverse Proxy Mark for follow up

Question 30 of 50. Besides selecting the Heartbeat Backup option when creating an Active-Passive HA Pair, which of the following also prevents "Split-Brain"? Configuring a backup HA2 link that points to the MGT interface of the other device in the pair. Creating a custom interface under Service Route Configuration, and assigning this interface as the backup HA2 link. Configuring an independent backup HA1 link. Under “Packet Forwarding”, selecting the VR Sync checkbox. Mark for follow up

Question 31 of 50. When troubleshooting Phase 1 of an IPsec VPN tunnel, which location and log will be most informative? Initiating side, System log Responding side, Traffic log Responding side, System Log Initiating side, Traffic log Mark for follow up

Question 32 of 50. Which statement about config locks is True? A config lock will expire after 24 hours, unless it was set by a superuser. A config lock can be removed only by the administrator who set it. A config lock can only be removed by the administrator who set it or by a superuser. A config lock can be removed only by a superuser. Mark for follow up

Question 33 of 50. What are two sources of information for determining whether the firewall has been successful in communicating with an external User-ID Agent? System Logs and the indicator light under the User-ID Agent settings in the firewall. System Logs and Authentication Logs. System Logs and an indicator light on the chassis. Traffic Logs and Authentication Logs. Mark for follow up

Question 34 of 50. Users may be authenticated sequentially to multiple authentication servers by configuring: An Authentication Sequence. A custom Administrator Profile. Multiple RADIUS servers sharing a VSA configuration. An Authentication Profile. Mark for follow up

Question 35 of 50. After the installation of a new Application and Threat database, the firewall must be rebooted. True

6 of 9

False

7/12/16, 5:22 PM

Realize Your Potential: paloaltonetworks

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?lo...

Mark for follow up

Question 36 of 50. Which feature can be configured to block sessions that the firewall cannot decrypt? Decryption Profile in Decryption Policy Decryption Profile in PBF Decryption Profile in Security Profile Decryption Profile in Security Policy Mark for follow up

Question 37 of 50. In PAN-OS 6.0 and later, which of these items may be used as match criterion in a Policy-Based Forwarding Rule? (Choose 3.) Destination Application Source Zone Destination Zone Source User

Mark for follow up

Question 38 of 50. Which of the following statements is NOT True about Palo Alto Networks firewalls? The default Admin account may be disabled or deleted. System defaults may be restored by performing a factory reset in Maintenance Mode. By default the MGT Port's IP Address is 192.168.1.1/24. Initial configuration may be accomplished thru the MGT interface or the Console port. Mark for follow up

Question 39 of 50. Previous to PAN-OS 7.0 the firewall was able to decode up to two levels. With PAN-OS 7.0 the firewall can now decode up to how many levels? Four Six Three Five Mark for follow up

Question 40 of 50. A Config Lock may be removed by which of the following users? (Select all correct answers.) The administrator who set it Any administrator Superusers Device administrators

Mark for follow up

Question 41 of 50. Which of the following is True of an application filter? An application filter automatically includes a new application when one of the new application’s characteristics are included in the filter. An application filter automatically adapts when an application moves from one IP address to another. An application filter specifies the users allowed to access an application. An application filter is used by malware to evade detection by firewalls and anti-virus software. Mark for follow up

7 of 9

7/12/16, 5:22 PM

Realize Your Potential: paloaltonetworks

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?lo...

Question 42 of 50. Palo Alto Networks offers WildFire users three solution types. These solution types are the WildFire Public Cloud, The WF-500 Private Appliance, and the WildFire Hybrid solution. What is the main reason and purpose for the WildFire Hybrid solution? The WildFire Hybrid solution enables companies to send to the WF-500 Private Appliance keeping them internal to their network, as well providing the option to send other, general files to the WildFire Public Cloud for analysis. The WildFire Hybrid solution enables outside companies to share the same WF-500 Appliance while at the same time allowing them to send only their private files to the private WF-500. The WildFire Hybrid solution places WF-500s at multiple places in the cloud, so that firewall appliances distributed throughout an enterprise's network receive WildFire verdicts with minimal latency while retaining data privacy. The WildFire Hybrid solution is only offered to companies that have sensitive files to protect and does not require a WildFire subscription. Mark for follow up

Question 43 of 50.

Taking into account only the information in the screenshot above, answer the following question. Which applications will be allowed on their standard ports? (Select all correct answers.) BitTorrent SSH Skype Gnutella

Mark for follow up

Question 44 of 50. WildFire may be used for identifying which of the following types of traffic? DHCP Malware RIPv2 OSPF Mark for follow up

Question 45 of 50. After the installation of a new version of PAN-OS, the firewall must be rebooted. True

False

Mark for follow up

Question 46 of 50. When using remote authentication for users (LDAP, RADIUS, Active Directory, etc.), what must be done to allow a user to authenticate through multiple methods? This cannot be done. A single user can only use one authentication type. Create an Authentication Sequence, dictating the order of authentication profiles. This cannot be done. Although multiple authentication methods exist, a firewall must choose a single, global authentication type--and all users must use this method. Create multiple authentication profiles for the same user. Mark for follow up

Question 47 of 50. An enterprise PKI system is required to deploy SSL Forward Proxy decryption capabilities. True

8 of 9

False

7/12/16, 5:22 PM

Realize Your Potential: paloaltonetworks

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?lo...

Mark for follow up

Question 48 of 50. Palo Alto Networks firewalls support the use of both Dynamic (built-in user roles) and Role-Based (customized user roles) for Administrator Accounts. True

False

Mark for follow up

Question 49 of 50. What general practice best describes how Palo Alto Networks firewall policies are applied to a session? The rule with the highest rule number is applied. First match applied. Last match applied. Most specific match applied. Mark for follow up

Question 50 of 50. When employing the BrightCloud URL filtering database in a Palo Alto Networks firewall, the order of evaluation within a profile is: Dynamic URL filtering, Block list, Allow list, Cache files, Custom categories, Predefined categories. Block list, Allow list, Custom Categories, Cache files, Local URL DB file. Block list, Custom Categories, Predefined categories, Dynamic URL filtering, Allow list, Cache files. Block list, Custom Categories, Cache files, Predefined categories, Dynamic URL filtering, Allow list. Mark for follow up

Save / Return Later

9 of 9

Summary

7/12/16, 5:22 PM

Realize Your Potential: paloaltonetworks

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?lo...

Test - Accredited Configuration Engineer (ACE) Exam - PAN-OS 7.0 Version ACE Exam

Question 1 of 50. Which of the following interface types can have an IP address assigned to it? Layer 3 Layer 2 Tap Virtual Wire Mark for follow up

Question 2 of 50. What general practice best describes how Palo Alto Networks firewall policies are applied to a session? First match applied. The rule with the highest rule number is applied. Last match applied. Most specific match applied. Mark for follow up

Question 3 of 50. Will an exported configuration contain Management Interface settings? Yes

No

Mark for follow up

Question 4 of 50. Which of the following are methods that HA clusters use to identify network outages? Path and Link Monitoring Link and Session Monitors VR and VSYS Monitors Heartbeat and Session Monitors Mark for follow up

Question 5 of 50. In a Destination NAT configuration, the Translated Address field may be populated with either an IP address or an Address Object. True

False

Mark for follow up

Question 6 of 50. Which of the following statements is NOT True about Palo Alto Networks firewalls? The default Admin account may be disabled or deleted. System defaults may be restored by performing a factory reset in Maintenance Mode. By default the MGT Port's IP Address is 192.168.1.1/24. Initial configuration may be accomplished thru the MGT interface or the Console port. Mark for follow up

Question 7 of 50. Which of the following is a routing protocol supported in a Palo Alto Networks firewall? RIPv2

1 of 9

7/11/16, 5:16 PM

Realize Your Potential: paloaltonetworks

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?lo...

IGRP ISIS EIGRP Mark for follow up

Question 8 of 50. Traffic going to a public IP address is being translated by a Palo Alto Networks firewall to an internal server’s private IP address. Which IP address should the Security Policy use as the "Destination IP" in order to allow traffic to the server? The firewall’s gateway IP The server’s private IP The firewall’s MGT IP The server’s public IP Mark for follow up

Question 9 of 50.

Taking into account only the information in the screenshot above, answer the following question. An administrator is using SSH on port 3333 and BitTorrent on port 7777. Which statements are True? The SSH traffic will be denied. The SSH traffic will be allowed. The BitTorrent traffic will be denied. The BitTorrent traffic will be allowed.

Mark for follow up

Question 10 of 50. In PAN-OS 6.0 and later, rule numbers are: Numbers that specify the order in which security policies are evaluated. Numbers created to be unique identifiers in each firewall’s policy database. Numbers on a scale of 0 to 99 that specify priorities when two or more rules are in conflict. Numbers created to make it easier for users to discuss a complicated or difficult sequence of rules. Mark for follow up

Question 11 of 50. Which of the following facts about dynamic updates is correct? Application and Threat updates are released daily. Anti-virus and URL Filtering updates are released weekly. Threat and URL Filtering updates are released daily. Application and Anti-virus updates are released weekly. Application and Anti-virus updates are released weekly. Threat and “Threat and URL Filtering” updates are released weekly. Anti-virus updates are released daily. Application and Threat updates are released weekly. Mark for follow up

Question 12 of 50. Reconnaissance Protection is a feature used to protect the Palo Alto Networks firewall from port scans. To enable this feature within the GUI go to… Network > Network Profiles > Zone Protection Objects > Zone Protection Interfaces > Interface Number > Zone Protection Policies > Profile > Zone Protection

2 of 9

7/11/16, 5:16 PM

Realize Your Potential: paloaltonetworks

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?lo...

Mark for follow up

Question 13 of 50. True or False: The WildFire Analysis Profile can only be configured to send unknown files to the WildFire Public Cloud only. True

False

Mark for follow up

Question 14 of 50. When using remote authentication for users (LDAP, RADIUS, Active Directory, etc.), what must be done to allow a user to authenticate through multiple methods? Create an Authentication Sequence, dictating the order of authentication profiles. This cannot be done. Although multiple authentication methods exist, a firewall must choose a single, global authentication type--and all users must use this method. This cannot be done. A single user can only use one authentication type. Create multiple authentication profiles for the same user. Mark for follow up

Question 15 of 50. After the installation of a new Application and Threat database, the firewall must be rebooted. True

False

Mark for follow up

Question 16 of 50. An interface in tap mode can transmit packets on the wire. True

False

Mark for follow up

Question 17 of 50. What will the user experience when attempting to access a blocked hacking website through a translation service such as Google Translate or Bing Translator? A “Blocked” page response when the URL filtering policy to block is enforced. A “Success” page response when the site is successfully translated. The browser will be redirected to the original website address. An "HTTP Error 503 - Service unavailable" message. Mark for follow up

Question 18 of 50. When employing the BrightCloud URL filtering database in a Palo Alto Networks firewall, the order of evaluation within a profile is: Block list, Custom Categories, Predefined categories, Dynamic URL filtering, Allow list, Cache files. Dynamic URL filtering, Block list, Allow list, Cache files, Custom categories, Predefined categories. Block list, Allow list, Custom Categories, Cache files, Local URL DB file. Block list, Custom Categories, Cache files, Predefined categories, Dynamic URL filtering, Allow list. Mark for follow up

Question 19 of 50. You can assign an IP address to an interface in Virtual Wire mode. True

False

Mark for follow up

Question 20 of 50. Palo Alto Networks firewalls support the use of both Dynamic (built-in user roles) and Role-Based (customized user roles) for Administrator Accounts. True

3 of 9

False

7/11/16, 5:16 PM

Realize Your Potential: paloaltonetworks

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?lo...

Mark for follow up

Question 21 of 50. Which of the following must be enabled in order for User-ID to function? Captive Portal Policies must be enabled. Captive Portal must be enabled. Security Policies must have the User-ID option enabled. User-ID must be enabled for the source zone of the traffic that is to be identified. Mark for follow up

Question 22 of 50. When configuring the firewall for User-ID, what is the maximum number of Domain Controllers that can be configured? 50 10 150 100 Mark for follow up

Question 23 of 50. Which of the following can provide information to a Palo Alto Networks firewall for the purposes of User-ID? (Select all correct answers.) SSL Certificates Domain Controller RIPv2 Network Access Control (NAC) device

Mark for follow up

Question 24 of 50. When you have created a Security Policy Rule that allows Facebook, what must you do to block all other web-browsing traffic? Nothing. You can depend on PAN-OS to block the web-browsing traffic that is not needed for Facebook use. Create an additional rule that blocks all other traffic. When creating the policy, ensure that web-browsing is included in the same rule. Ensure that the Service column is defined as "application-default" for this Security policy. Doing this will automatically include the implicit web-browsing application dependency. Mark for follow up

Question 25 of 50.

Taking into account only the information in the screenshot above, answer the following question. Which applications will be allowed on their standard ports? (Select all correct answers.) SSH BitTorrent Skype Gnutella

Mark for follow up

4 of 9

7/11/16, 5:16 PM

Realize Your Potential: paloaltonetworks

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?lo...

Question 26 of 50. In order to route traffic between Layer 3 interfaces on the Palo Alto Networks firewall, you need a: Virtual Router VLAN Virtual Wire Security Profile Mark for follow up

Question 27 of 50. As the Palo Alto Networks Administrator responsible for User-ID, you need to enable mapping of network users that do not sign-in using LDAP. Which information source would allow for reliable User-ID mapping while requiring the least effort to configure? WMI Query Exchange CAS Security logs Active Directory Security Logs Captive Portal Mark for follow up

Question 28 of 50. An enterprise PKI system is required to deploy SSL Forward Proxy decryption capabilities. True

False

Mark for follow up

Question 29 of 50. When using Config Audit, the color yellow indicates which of the following? A setting has been changed between the two config files A setting has been deleted from a config file. A setting has been added to a config file An invalid value has been used in a config file. Mark for follow up

Question 30 of 50. With IKE Phase 1, each device is identified to the other by a Peer ID. In most cases, the Peer ID is just the public IP address of the device. In situations where the public IP address is not static, the Peer ID can be a text value. True

False

Mark for follow up

Question 31 of 50. True or False: The PAN-DB URL Filtering Service is offered as both a Private Cloud solution and a Public Cloud solution. True

False

Mark for follow up

Question 32 of 50. Which of the following is NOT a valid option for built-in CLI Admin roles? deviceadmin superuser read/write devicereader Mark for follow up

Question 33 of 50.

5 of 9

7/11/16, 5:16 PM

Realize Your Potential: paloaltonetworks

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?lo...

Which pre-defined Admin Role has all rights except the rights to create administrative accounts and virtual systems? vsysadmin Superuser Device Administrator A custom admin role must be created for this specific combination of rights. Mark for follow up

Question 34 of 50. When configuring a Decryption Policy rule, which option allows a firewall administrator to control SSHv2 tunneling in policies by specifying the SSH-tunnel App-ID? SSH Proxy SSL Forward Proxy SSL Inbound Inspection SSL Reverse Proxy Mark for follow up

Question 35 of 50. Which feature can be configured to block sessions that the firewall cannot decrypt? Decryption Profile in Decryption Policy Decryption Profile in PBF Decryption Profile in Security Profile Decryption Profile in Security Policy Mark for follow up

Question 36 of 50. Users may be authenticated sequentially to multiple authentication servers by configuring: An Authentication Sequence. A custom Administrator Profile. Multiple RADIUS servers sharing a VSA configuration. An Authentication Profile. Mark for follow up

Question 37 of 50. After the installation of a new version of PAN-OS, the firewall must be rebooted. True

False

Mark for follow up

Question 38 of 50. In PAN-OS 7.0 which of the available choices serves as an alert warning by defining patterns of suspicious traffic and network anomalies that may indicate a host has been compromised? Command & Control Signatures Correlation Objects App-ID Signatures Custom Signatures Correlation Events Mark for follow up

Question 39 of 50. Which statement about config locks is True? A config lock can only be removed by the administrator who set it or by a superuser. A config lock can be removed only by a superuser. A config lock can be removed only by the administrator who set it.

6 of 9

7/11/16, 5:16 PM

Realize Your Potential: paloaltonetworks

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?lo...

A config lock will expire after 24 hours, unless it was set by a superuser. Mark for follow up

Question 40 of 50. Using the API in PAN-OS 6.1, WildFire subscribers can upload up to how many samples per day? 1000 500 50 10 Mark for follow up

Question 41 of 50. Which of the following CANNOT use the source user as a match criterion? DoS Protection Anti-virus Profile QoS Secuirty Policies Policy Based Forwarding Mark for follow up

Question 42 of 50. Color-coded tags can be used on all of the items listed below EXCEPT: Zones Address Objects Vulnerability Profiles Service Groups Mark for follow up

Question 43 of 50. Which of the following is True of an application filter? An application filter is used by malware to evade detection by firewalls and anti-virus software. An application filter specifies the users allowed to access an application. An application filter automatically includes a new application when one of the new application’s characteristics are included in the filter. An application filter automatically adapts when an application moves from one IP address to another. Mark for follow up

Question 44 of 50. The "Drive-By Download" protection feature, under File Blocking profiles in Content-ID, provides: Password-protected access to specific file downloads for authorized users. Increased speed on downloads of file types that are explicitly enabled. Protection against unwanted downloads by showing the user a response page indicating that a file is going to be downloaded. The ability to use Authentication Profiles, in order to protect against unwanted downloads. Mark for follow up

Question 45 of 50. Select the implicit rules that are applied to traffic that fails to match any administrator-defined Security Policies. (Choose all rules that are correct.) Intra-zone traffic is allowed Inter-zone traffic is denied Intra-zone traffic is denied Inter-zone traffic is allowed

7 of 9

7/11/16, 5:16 PM

Realize Your Potential: paloaltonetworks

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?lo...

Mark for follow up

Question 46 of 50.

Taking into account only the information in the screenshot above, answer the following question: A span port or a switch is connected to e1/4, but there are no traffic logs. Which of the following conditions most likely explains this behavior? The interface is not assigned an IP address. The interface is not assigned a virtual router. The interface is not up. There is no zone assigned to the interface. Mark for follow up

Question 47 of 50. What will be the user experience when the safe search option is NOT enabled for Google search but the firewall has "Safe Search Enforcement" Enabled? The user will be redirected to a different search site that is specified by the firewall administrator. The Firewall will enforce Safe Search if the URL filtering license is still valid. A task bar pop-up message will be presented to enable Safe Search. A block page will be presented with instructions on how to set the strict Safe Search option for the Google search. Mark for follow up

Question 48 of 50. Which type of license is required to perform Decryption Port Mirroring? A Client Decryption license A subscription-based PAN-PA-Decrypt license A subscription-based SSL Port license A free PAN-PA-Decrypt license Mark for follow up

Question 49 of 50. Besides selecting the Heartbeat Backup option when creating an Active-Passive HA Pair, which of the following also prevents "Split-Brain"? Creating a custom interface under Service Route Configuration, and assigning this interface as the backup HA2 link. Configuring an independent backup HA1 link. Configuring a backup HA2 link that points to the MGT interface of the other device in the pair. Under “Packet Forwarding”, selecting the VR Sync checkbox. Mark for follow up

Question 50 of 50. Which of the following services are enabled on the MGT interface by default? (Select all correct answers.) HTTPS SSH Telnet HTTP

8 of 9

7/11/16, 5:16 PM

Realize Your Potential: paloaltonetworks

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?lo...

Mark for follow up

Save / Return Later

9 of 9

Summary

7/11/16, 5:16 PM

20/12/2015

Realize Your Potential: paloaltonetworks

Test ­ Accredited Configuration Engineer (ACE) Exam ­ PAN­OS 7.0 Version ACE Exam 

Question 1 of 50.  When configuring a Security Policy Rule based on FQDN Address Objects, which of the following statements is True?   The firewall resolves the FQDN first when the policy is committed, and resolves the FQDN again each time Security Profiles are evaluated.   The firewall resolves the FQDN first when the policy is committed, and resolves the FQDN again at DNS TTL expiration.   In order to create FQDN­based objects, you need to manually define a list of associated IP addresses.     Mark for follow up

Question 2 of 50.  Using the API in PAN­OS 6.1, WildFire subscribers can upload up to how many samples per day?   50   1000   500   10     Mark for follow up

Question 3 of 50.  In Palo Alto Networks terms, an application is:   A specific program detected within an identified stream that can be detected, monitored, and/or blocked.   A combination of port and protocol that can be detected, monitored, and/or blocked.   A file installed on a local machine that can be detected, monitored, and/or blocked.   Web­based traffic from a specific IP address that can be detected, monitored, and/or blocked.     Mark for follow up

Question 4 of 50.  What is the default setting for 'Action' in a Decryption Policy's rule?   Any   No­Decrypt   None   Decrypt     Mark for follow up

Question 5 of 50.  When Destination Network Address Translation is being performed, the destination in the corresponding Security Policy Rule should use:   The Post­NAT destination zone and Pre­NAT IP addresses.   The Post­NAT destination zone and Post­NAT IP addresses.   The Pre­NAT destination zone and Post­NAT IP addresses.   The Pre­NAT destination zone and Pre­NAT IP addresses.     Mark for follow up

Question 6 of 50.  All of the interfaces on a Palo Alto Networks device must be of the same interface type. True False  

 

 

Mark for follow up

Question 7 of 50.  When using Config Audit, the color yellow indicates which of the following?   A setting has been changed between the two config files   A setting has been deleted from a config file.   A setting has been added to a config file  

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?loid=e9d5a4ee­d001­44d4­8d3a­07d77495f928&evalLvl=5&redirect_url=%2fphnx%2fdriver.as…

1/8

20/12/2015

Realize Your Potential: paloaltonetworks

An invalid value has been used in a config file.     Mark for follow up

Question 8 of 50.  Which of the following is NOT a valid option for built­in CLI Admin roles?   read/write   superuser   deviceadmin   devicereader     Mark for follow up

Question 9 of 50.  Security policy rules specify a source interface and a destination interface. True False  

 

 

Mark for follow up

Question 10 of 50. 

Taking into account only the information in the screenshot above, answer the following question. An administrator is using SSH on port 3333 and BitTorrent on port 7777. Which statements are True? The BitTorrent traffic will be allowed.   The SSH traffic will be denied.   The BitTorrent traffic will be denied.   The SSH traffic will be allowed.       Mark for follow up

Question 11 of 50.  After the installation of the Threat Prevention license, the firewall must be rebooted. True False  

 

 

Mark for follow up

Question 12 of 50.  Attackers will employ a number of tactics to hide malware. One such tactic is to encode and/or compress the file so as to hide the malware. With PAN­OS 7.0 the firewall can decode up to four levels. But if an attacker has encoded the file beyond four levels, what can you as an administer do to protect your users?   Create a Decryption Profile for multi­level encoded files and apply it to a Decryption Policy.   Create a File Blocking Profile for multi­level encoded files and apply it to a Decryption Policy.   Create a File Blocking Profile for multi­level encoded files with the action set to block.   Create a Decryption Policy for multi­level encoded files and set the action to block.     Mark for follow up

Question 13 of 50.  Will an exported configuration contain Management Interface settings? Yes No  

 

 

Mark for follow up

Question 14 of 50.  When troubleshooting Phase 1 of an IPsec VPN tunnel, which location and log will be most informative?  

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?loid=e9d5a4ee­d001­44d4­8d3a­07d77495f928&evalLvl=5&redirect_url=%2fphnx%2fdriver.as…

2/8

20/12/2015

Realize Your Potential: paloaltonetworks

Initiating side, System log   Initiating side, Traffic log   Responding side, System Log   Responding side, Traffic log     Mark for follow up

Question 15 of 50.  Which of the following interface types can have an IP address assigned to it?   Layer 3   Layer 2   Tap   Virtual Wire     Mark for follow up

Question 16 of 50.  An interface in tap mode can transmit packets on the wire. True False  

 

 

Mark for follow up

Question 17 of 50.  Select the implicit rules that are applied to traffic that fails to match any administrator­defined Security Policies. (Choose all rules that are correct.) Intra­zone traffic is allowed   Inter­zone traffic is denied   Intra­zone traffic is denied   Inter­zone traffic is allowed       Mark for follow up

Question 18 of 50.  Which statement about config locks is True?   A config lock can only be removed by the administrator who set it or by a superuser.   A config lock can be removed only by the administrator who set it.   A config lock will expire after 24 hours, unless it was set by a superuser.   A config lock can be removed only by a superuser.     Mark for follow up

Question 19 of 50.  When you have created a Security Policy Rule that allows Facebook, what must you do to block all other web­browsing traffic?   Nothing. You can depend on PAN­OS to block the web­browsing traffic that is not needed for Facebook use.   When creating the policy, ensure that web­browsing is included in the same rule.   Create an additional rule that blocks all other traffic.   Ensure that the Service column is defined as "application­default" for this Security policy. Doing this will automatically include the implicit web­browsing application dependency.     Mark for follow up

Question 20 of 50.  Without a WildFire subscription, which of the following files can be submitted by the Firewall to the hosted WildFire virtualized sandbox?   PE files only   MS Office doc/docx, xls/xlsx, and ppt/pptx files only   PDF files only   PE and Java Applet (jar and class) only     Mark for follow up

Question 21 of 50.  Users may be authenticated sequentially to multiple authentication servers by configuring:   An Authentication Sequence.  

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?loid=e9d5a4ee­d001­44d4­8d3a­07d77495f928&evalLvl=5&redirect_url=%2fphnx%2fdriver.as…

3/8

20/12/2015

Realize Your Potential: paloaltonetworks

An Authentication Profile.   A custom Administrator Profile.   Multiple RADIUS servers sharing a VSA configuration.     Mark for follow up

Question 22 of 50.  WildFire may be used for identifying which of the following types of traffic?   Malware   RIPv2   DHCP   OSPF     Mark for follow up

Question 23 of 50.  When using remote authentication for users (LDAP, RADIUS, Active Directory, etc.), what must be done to allow a user to authenticate through multiple methods?   Create an Authentication Sequence, dictating the order of authentication profiles.   This cannot be done. Although multiple authentication methods exist, a firewall must choose a single, global authentication type­­and all users must use this method.   This cannot be done. A single user can only use one authentication type.   Create multiple authentication profiles for the same user.     Mark for follow up

Question 24 of 50. 

Considering the information in the screenshot above, what is the order of evaluation for this URL Filtering Profile?   Allow List, Block List, Custom Categories, URL Categories (BrightCloud or PAN­DB).   URL Categories (BrightCloud or PAN­DB), Custom Categories, Block List, Allow List.   Block List, Allow List, Custom Categories, URL Categories (BrightCloud or PAN­DB).   Block List, Allow List, URL Categories (BrightCloud or PAN­DB), Custom Categories.     Mark for follow up

Question 25 of 50.  Which type of license is required to perform Decryption Port Mirroring?   A Client Decryption license   A subscription­based SSL Port license   A free PAN­PA­Decrypt license   A subscription­based PAN­PA­Decrypt license     Mark for follow up

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?loid=e9d5a4ee­d001­44d4­8d3a­07d77495f928&evalLvl=5&redirect_url=%2fphnx%2fdriver.as…

4/8

20/12/2015

Realize Your Potential: paloaltonetworks

Question 26 of 50.  Can multiple administrator accounts be configured on a single firewall? Yes No  

 

 

Mark for follow up

Question 27 of 50. 

Taking into account only the information in the screenshot above, answer the following question: A span port or a switch is connected to e1/4, but there are no traffic logs. Which of the following conditions most likely explains this behavior?   The interface is not assigned an IP address.   The interface is not up.   There is no zone assigned to the interface.   The interface is not assigned a virtual router.     Mark for follow up

Question 28 of 50.  Which pre­defined Admin Role has all rights except the rights to create administrative accounts and virtual systems?   Superuser   vsysadmin   Device Administrator   A custom admin role must be created for this specific combination of rights.     Mark for follow up

Question 29 of 50. 

The screenshot above shows part of a firewall’s configuration. If ping traffic can traverse this device from e1/2 to e1/1, which of the following statements must be True about this firewall’s configuration? (Select all correct answers.) There must be appropriate routes in the default virtual router.   There must be a security policy rule from Internet zone to trust zone that allows ping.   There must be a security policy rule from trust zone to Internet zone that allows ping.   There must be a Management Profile that allows ping. (Then assign that Management Profile to e1/1 and e1/2.)       Mark for follow up

Question 30 of 50.  Which of the following is a routing protocol supported in a Palo Alto Networks firewall?

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?loid=e9d5a4ee­d001­44d4­8d3a­07d77495f928&evalLvl=5&redirect_url=%2fphnx%2fdriver.as…

5/8

20/12/2015

Realize Your Potential: paloaltonetworks

  RIPv2   IGRP   EIGRP   ISIS     Mark for follow up

Question 31 of 50.  WildFire analyzes files to determine whether or not they are malicious. When doing so, WildFire will classify the file with an official verdict. This verdict is known as the WildFire Analysis verdict. Choose the three correct classifications as a result of this analysis and classification? Benign   Spyware   Safeware   Adware   Grayware   Malware detection       Mark for follow up

Question 32 of 50.  When employing the BrightCloud URL filtering database in a Palo Alto Networks firewall, the order of evaluation within a profile is:   Block list, Allow list, Custom Categories, Cache files, Local URL DB file.   Dynamic URL filtering, Block list, Allow list, Cache files, Custom categories, Predefined categories.   Block list, Custom Categories, Predefined categories, Dynamic URL filtering, Allow list, Cache files.   Block list, Custom Categories, Cache files, Predefined categories, Dynamic URL filtering, Allow list.     Mark for follow up

Question 33 of 50.  In PAN­OS 7.0 which of the available choices serves as an alert warning by defining patterns of suspicious traffic and network anomalies that may indicate a host has been compromised?   Correlation Objects   App­ID Signatures   Command & Control Signatures   Custom Signatures   Correlation Events     Mark for follow up

Question 34 of 50.  True or False: The WildFire Analysis Profile can only be configured to send unknown files to the WildFire Public Cloud only. True False  

 

 

Mark for follow up

Question 35 of 50.  Which of the following most accurately describes Dynamic IP in a Source NAT configuration?   The next available IP address in the configured pool is used, but the source port number is unchanged.   A single IP address is used, and the source port number is changed.   The next available address in the configured pool is used, and the source port number is changed.   A single IP address is used, and the source port number is unchanged.     Mark for follow up

Question 36 of 50.  What will be the user experience when the safe search option is NOT enabled for Google search but the firewall has "Safe Search Enforcement" Enabled?   A block page will be presented with instructions on how to set the strict Safe Search option for the Google search.   The user will be redirected to a different search site that is specified by the firewall administrator.   A task bar pop­up message will be presented to enable Safe Search.   The Firewall will enforce Safe Search if the URL filtering license is still valid.     Mark for follow up

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?loid=e9d5a4ee­d001­44d4­8d3a­07d77495f928&evalLvl=5&redirect_url=%2fphnx%2fdriver.as…

6/8

20/12/2015

Realize Your Potential: paloaltonetworks

Question 37 of 50.  In PAN­OS 6.0 and later, which of these items may be used as match criterion in a Policy­Based Forwarding Rule? (Choose 3.) Destination Application   Source Zone   Source User   Destination Zone       Mark for follow up

Question 38 of 50.  A "Continue" action can be configured on which of the following Security Profiles?   URL Filtering and File Blocking   URL Filtering only   URL Filtering, File Blocking, and Data Filtering   URL Filtering and Anti­virus     Mark for follow up

Question 39 of 50.  Palo Alto Networks firewalls support the use of both Dynamic (built­in user roles) and Role­Based (customized user roles) for Administrator Accounts. True False  

 

 

Mark for follow up

Question 40 of 50.  Which of the following facts about dynamic updates is correct?   Anti­virus updates are released daily. Application and Threat updates are released weekly.   Application and Threat updates are released daily. Anti­virus and URL Filtering updates are released weekly.   Application and Anti­virus updates are released weekly. Threat and “Threat and URL Filtering” updates are released weekly.   Threat and URL Filtering updates are released daily. Application and Anti­virus updates are released weekly.     Mark for follow up

Question 41 of 50.  Previous to PAN­OS 7.0 the firewall was able to decode up to two levels. With PAN­OS 7.0 the firewall can now decode up to how many levels?   Four   Three   Five   Six     Mark for follow up

Question 42 of 50.  Which of the following would be a reason to use the PAN­OS XML API to communicate with a Palo Alto Networks firewall?   To pull information from other network resources for User­ID.   To permit syslogging of User Identification events.   To allow the firewall to push User­ID information to a Network Access Control (NAC) device.     Mark for follow up

Question 43 of 50.  PAN­OS 7.0 introduced a new Security Profile type. What is the name of this new security profile type?   Threat Analysis   WildFire Analysis   Malware Analysis   File Analysis     Mark for follow up

Question 44 of 50. 

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?loid=e9d5a4ee­d001­44d4­8d3a­07d77495f928&evalLvl=5&redirect_url=%2fphnx%2fdriver.as…

7/8

20/12/2015

Realize Your Potential: paloaltonetworks

You can assign an IP address to an interface in Virtual Wire mode. True False  

 

 

Mark for follow up

Question 45 of 50.  Which of the following are methods that HA clusters use to identify network outages?   Link and Session Monitors   Path and Link Monitoring   Heartbeat and Session Monitors   VR and VSYS Monitors     Mark for follow up

Question 46 of 50.  When an interface is in Tap mode and a Policy’s action is set to “block”, the interface will send a TCP reset. True False  

 

 

Mark for follow up

Question 47 of 50.  How do you reduce the amount of information recorded in the URL Content Filtering Logs?   Enable "Log container page only".   Disable URL packet captures.   Enable URL log caching.   Enable DSRI.     Mark for follow up

Question 48 of 50.  What will the user experience when attempting to access a blocked hacking website through a translation service such as Google Translate or Bing Translator?   A “Blocked” page response when the URL filtering policy to block is enforced.   A “Success” page response when the site is successfully translated.   The browser will be redirected to the original website address.   An "HTTP Error 503 ­ Service unavailable" message.     Mark for follow up

Question 49 of 50.  True or False: The PAN­DB URL Filtering Service is offered as both a Private Cloud solution and a Public Cloud solution. True False  

 

 

Mark for follow up

Question 50 of 50.  With IKE Phase 1, each device is identified to the other by a Peer ID. In most cases, the Peer ID is just the public IP address of the device. In situations where the public IP address is not static, the Peer ID can be a text value. True False  

 

 

Mark for follow up

Save / Return Later

Summary

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?loid=e9d5a4ee­d001­44d4­8d3a­07d77495f928&evalLvl=5&redirect_url=%2fphnx%2fdriver.as…

8/8

Palo Alto Networks PCNSE6

Palo Alto Networks Certified Network Security Engineer 6.0 Version: 4.1

Palo Alto Networks PCNSE6 Exam QUESTION NO: 1 Which authentication method can provide role-based administrative access to firewalls running PAN-OS? A. LDAP B. Certificate-based authentication C. Kerberos D. RADIUS with Vendor Specific Attributes Answer: D Explanation:

QUESTION NO: 2 HOTSPOT Assuming that the default antivirus profile is installed, match each decoder with its default action. Answer options may be used more than once or not at all.

www.braindumps.com

2

Palo Alto Networks PCNSE6 Exam

Answer:

www.braindumps.com

3

Palo Alto Networks PCNSE6 Exam

Explanation: FTP, SMB – Block HTTP – Block POP3, SMTP – Alert IMAP – Alert

QUESTION NO: 3 Which three engines are built into the Single-Pass Parallel Processing Architecture? Choose 3 answers

www.braindumps.com

4

Palo Alto Networks PCNSE6 Exam A. Application Identification (App-ID) B. Group Identification (Group-ID) C. User Identification (User-ID) D. Threat Identification (Threat-ID) E. Content Identification (Content-ID) Answer: A,C,E Reference: https://www.paloaltonetworks.com/content/dam/paloaltonetworkscom/en_US/assets/pdf/white-papers/single-pass-parallel-processing-architecture.pdf page 5

QUESTION NO: 4 HOTSPOT Within a Zone Protection Profile, under the Reconnaissance Protection tab, there are several possible values for Action:

Match each Reconnaissance Protection Action to its description. Answer options may be used more than once or not at all.

www.braindumps.com

5

Palo Alto Networks PCNSE6 Exam

Answer:

www.braindumps.com

6

Palo Alto Networks PCNSE6 Exam Explanation: Allow: Permits the port scan attempts. Alert: Generates an alert for each scan that matches the threshold within the specified time interval. Block: Drops all traffic from the source to the destination. Block IP: Drops all traffic for a specific period of time (in seconds). There are two options: • Source: Blocks traffic from the source • Source-and-Destination: Blocks traffic for the source-destination pair https://live.paloaltonetworks.com/servlet/JiveServlet/previewBody/5078-102-514892/Understanding_DoS_Protection.pdf

QUESTION NO: 5 What is a prerequisite for configuring a pair of Palo Alto Networks firewalls in an Active/Passive High Availability (HA) pair? A. The peer HA1 IP address must be the same on both firewalls. B. The management interfaces must be on the same network. C. The firewalls must have the same set of licenses. D. The HA interfaces must be directly connected to each other. Answer: C Reference: https://www.paloaltonetworks.com/content/dam/paloaltonetworkscom/en_US/assets/pdf/framemaker/60/pan-os/pan-os/section_4.pdf page 134

QUESTION NO: 6 Which source address translation type will allow multiple devices to share a single translated source address while using a single NAT Policy rule? A. Dynamic IP and Port B. Dynamic IP C. Bi-directional D. Static IP Answer: A Reference: https://www.paloaltonetworks.com/documentation/61/pan-os/panwww.braindumps.com

7

Palo Alto Networks PCNSE6 Exam os/networking/nat.html

QUESTION NO: 7 HOTSPOT Match each type of report provided by the firewall with its description. Answer options may be used more than once or not at all.

Answer:

www.braindumps.com

8

Palo Alto Networks PCNSE6 Exam

Explanation: PDF Summary Reports – Reports that combine up to 18 custom or predefined reports from the Threat, Application, Traffic, URL Filtering Categories into one document. Report Groups – Reports the combine other custom and predefined reports into a single file to be emailed to one or more recipients. Custom Reports – Reports created by an administrator that filter on conditions and columns User or Groups Activity Reports – Reports on the application use and URL activity for a specific user or a group Reference: https://www.paloaltonetworks.com/content/dam/paloaltonetworkscom/en_US/assets/pdf/framemaker/61/panorama/Panorama_AdminGuide/section_6.pdf page 151

QUESTION NO: 8

www.braindumps.com

9

Palo Alto Networks PCNSE6 Exam How can a Palo Alto Networks firewall be configured to send syslog messages in a format compatible with nonstandard syslog servers? A. Enable support for non-standard syslog messages under device management. B. Select a non-standard syslog server profile. C. Create a custom log format under the syslog server profile. D. Check the custom-format checkbox in the syslog server profile. Answer: C Reference: https://live.paloaltonetworks.com/docs/DOC-2021 Page 16 of PDF available there.

QUESTION NO: 9 Which Public Key Infrastructure component is used to authenticate users for GlobalProtect when the Connect Method is set to "pre-logon"? A. Certificate Revocation List B. Trusted root certificate C. Machine certificate D. Online Certificate Status Protocol Answer: C Reference: https://www.paloaltonetworks.com/content/dam/paloaltonetworkscom/en_US/assets/pdf/framemaker/60/globalprotect/Global_Protect_6.0.pdf page 12.

QUESTION NO: 10 A company is in the process of upgrading their existing Palo Alto Networks firewalls from version 6.1.0 to 6.1.1. Which three methods can the firewall administrator use to install PAN-OS 6.1.1 across the enterprise? Choose 3 answers A. Push the PAN-OS 6.1.1 updates from the support site to install on each firewall. B. Download PAN-OS 6.1.1 files from the support site and install them on each firewall after manually uploading. C. Download PAN-OS 6.1.1 to a USB drive and the firewall will automatically update after the USB drive is inserted in the firewall. www.braindumps.com

10

Palo Alto Networks PCNSE6 Exam D. Push the PAN-OS 6.1.1 update from one firewall to all of the other remaining after updating one firewall. E. Download and push PAN-OS 6.1.1 from Panorama to each firewall. F. Download and install PAN-OS 6.1.1 directly on each firewall. Answer: B,E,F Reference: https://live.paloaltonetworks.com/docs/DOC-1062

QUESTION NO: 11 Given the following routing table:

Which configuration change on the firewall would cause it to use 10.66.24.88 as the nexthop for the 192.168.93.0/30 network? A. Configuring the Administrative Distance for RIP to be higher than that of OSPF Ext B. Configuring the metric for RIP to be higher than that of OSPF Int C. Configuring the metric for RIP to be lower than that of OSPF Ext D. Configuring the Administrative Distance for RIP to be lower than that of OSPF Int Answer: D Reference: https://live.paloaltonetworks.com/servlet/JiveServlet/previewBody/5284-102-317278/Route%20Redistribution%20and%20Filtering%20TechNote%20-%20Rev%20B.pdf

QUESTION NO: 12

www.braindumps.com

11

Palo Alto Networks PCNSE6 Exam A company hosts a publicly-accessible web server behind their Palo Alto Networks firewall, with this configuration information: -

Users outside the company are in the "Untrust-L3" zone. The web server physically resides in the "Trust-L3" zone. Web server public IP address: 1.1.1.1 Web server private IP address: 192.168.1.10

Which NAT Policy rule will allow users outside the company to access the web server?

A. Option A B. Option B C. Option C D. Option D Answer: B Explanation:

QUESTION NO: 13 A company has purchased a WildFire subscription and would like to implement dynamic updates to download the most recent content as often as possible. What is the shortest time interval the company can configure their firewall to check for WildFire updates? A. Every 24 hours B. Every 30 minutes C. Every 15 minutes D. Every 1 hour www.braindumps.com

12

Palo Alto Networks PCNSE6 Exam E. Every 5 minutes Answer: C Reference: https://www.paloaltonetworks.com/content/dam/paloaltonetworkscom/en_US/assets/pdf/framemaker/60/wildfire/WF_Admin/section_1.pdf page 11

QUESTION NO: 14 Which method is the most efficient for determining which administrator made a specific change to the running config? A. In the Configuration log, set a filter for the edit command and look for the object that was changed. B. In the System log, set a filter for the name of the object that was changed. C. In Config Audit, compare the current running config to all of the saved configurations until the change is found. D. In Config Audit, compare the current running config to previous committed versions until the change is found. Answer: B Explanation:

QUESTION NO: 15 You are configuring a File Blocking Profile to be applied to all outbound traffic uploading a specific file type, and there is a specific application that you want to match in the policy. What are three valid actions that can be set when the specified file is detected? Choose 3 answers A. Reset-both B. Block C. Continue D. Continue-and-forward E. Upload Answer: B,C,D Reference: https://www.paloaltonetworks.com/content/dam/paloaltonetworkscom/en_US/assets/pdf/framemaker/60/pan-os/pan-os/section_8.pdf page 287

www.braindumps.com

13

Palo Alto Networks PCNSE6 Exam

QUESTION NO: 16 Two firewalls are configured in an Active/Passive High Availability (HA) pair with the following election settings:

Firewall 5050-B is presently in the "Active" state and 5050-A is presently in the "Passive" state. Firewall 5050-B reboots causing 5050-A to become Active. Which firewall will be in the "Active" state after firewall 5050-B has completed its reboot and is back online? A. Both firewalls are active (split brain) B. Firewall 5050-B C. Firewall 5050-A D. It could be either firewall Answer: B Reference: https://live.paloaltonetworks.com/docs/DOC-2926

QUESTION NO: 17 Which two statements are true about DoS Protection Profiles and Policies? Choose 2 answers A. They mitigate against SYN, UDP, ICMP, ICMPv6, and other IP Flood attacks on a zone basis, regardless of interface(s). They provide reconnaissance protection against TCP/UDP port scans and host sweeps. B. They mitigate against SYN, UDP, ICMP, ICMPv6, and other IP Flood attacks. They provide resource protection by limiting the number of sessions that can be used. C. They mitigate against volumetric attacks that leverage known vulnerabilities, brute force methods, amplification, spoofing, and other vulnerabilities. D. They mitigate against SYN, UDP, ICMP, ICMPv6, and other IP Flood attacks by utilizing "random early drop".

www.braindumps.com

14

Palo Alto Networks PCNSE6 Exam Answer: B,D Reference: https://live.paloaltonetworks.com/servlet/JiveServlet/previewBody/7158-102-325328/Application%20DDoS%20Mitigation.pdf page 4

QUESTION NO: 18 Where can the maximum concurrent SSL VPN Tunnels be set for Vsys2 when provisioning a Palo Alto Networks firewall for multiple virtual systems? A. In the GUI under Network->Global Protect->Gateway->Vsys2 B. In the GUI under Device->Setup->Session->Session Settings C. In the GUI under Device->Virtual Systems->Vsys2->Resource D. In the GUI under Network->Global Protect->Portal->Vsys2 Answer: C Reference: https://www.paloaltonetworks.com/content/dam/paloaltonetworkscom/en_US/assets/pdf/tech-briefs/virtual-systems.pdf page 6

QUESTION NO: 19 A security engineer has been asked by management to optimize how Palo Alto Networks firewall syslog messages are forwarded to a syslog receiver. There are currently 20 PA-5060 s, each of which is configured to forward syslogs individually. The security engineer would like to leverage their two M-100 appliances to send syslog messages from a single source and has already deployed one in Panorama mode and the other as a Log Collector. What is the remaining step in implementing this solution? A. Configure Collector Log Forwarding B. Configure a Syslog Proxy Profile C. Configure a Panorama Log Forwarding Profile D. Enable Syslog Aggregation Answer: A Reference: https://live.paloaltonetworks.com/docs/DOC-7987

www.braindumps.com

15

Palo Alto Networks PCNSE6 Exam

QUESTION NO: 20 What can cause missing SSL packets when performing a packet capture on data plane interfaces? A. There is a hardware problem with the offloading FPGA on the management plane. B. The missing packets are offloaded to the management plane CPU. C. The packets are hardware offloaded to the offload processor on the data plane. D. The packets are not captured because they are encrypted. Answer: C Reference: https://live.paloaltonetworks.com/docs/DOC-8621

QUESTION NO: 21 A company has a policy that denies all applications they classify as bad and permits only applications they classify as good. The firewall administrator created the following security policy on the company s firewall:

Which two benefits are gained from having both rule 2 and rule 3 present? Choose 2 answers A. Different security profiles can be applied to traffic matching rules 2 and 3. B. Separate Log Forwarding profiles can be applied to rules 2 and 3. C. Rule 2 denies traffic flowing across different TCP and UDP ports than rule 3. D. A report can be created that identifies unclassified traffic on the network. Answer: A,D Explanation:

QUESTION NO: 22

www.braindumps.com

16

Palo Alto Networks PCNSE6 Exam Company employees have been given access to the GlobalProtect Portal at https://portal.company.com:

Assume the following: 1. The firewall is configured to resolve DNS names using the internal DNS server. 2. The URL portal.company.com resolves to the external interface of the firewall on the company’s external DNS server and to the internal interface of the firewall on the company s internal DNS server. 3. The URL gatewayl.company.com resolves to the external interface of the firewall on the company’s external DNS server and to the internal interface of the firewall on the company s internal DNS server. This Gateway configuration will have which two outcomes? Choose 2 answers A. Clients outside the network will be able to connect to the external gateway Gateway1. B. Clients inside the network will be able to connect to the internal gateway Gateway1. C. Clients outside the network will NOT be able to connect to the external gateway Gateway1. D. Clients inside the network will NOT be able to connect to the internal gateway Gateway1. Answer: A,B Explanation:

QUESTION NO: 23 www.braindumps.com

17

Palo Alto Networks PCNSE6 Exam What is the maximum usable storage capacity of an M-100 appliance? A. 2TB B. 4TB C. 6TB D. STB Answer: B Reference: https://www.paloaltonetworks.com/documentation/61/panorama/panorama_adminguide/set-uppanorama/set-up-the-m-100-appliance.html

QUESTION NO: 24 A user is reporting that they cannot download a PDF file from the internet. Which action will show whether the downloaded file has been blocked by a Security Profile? A. Filter the Session Browser for all sessions from the user with the application "adobe". B. Filter the System log for "Download Failed" messages. C. Filter the Traffic logs for all traffic from the user that resulted in a Deny action. D. Filter the Data Filtering logs for the user’s traffic and the name of the PDF file. Answer: D Explanation:

QUESTION NO: 25 What has happened when the traffic log shows an internal host attempting to open a session to a properly configured sinkhole address? A. The internal host is trying to resolve a DNS query by connecting to a rogue DNS server. B. The internal host attempted to use DNS to resolve a known malicious domain into an IP address. C. A rogue DNS server is now using the sinkhole address to direct traffic to a known malicious domain. D. A malicious domain is trying to contact an internal DNS server. Answer: B www.braindumps.com

18

Palo Alto Networks PCNSE6 Exam Reference: https://www.paloaltonetworks.jp/content/dam/paloaltonetworkscom/en_US/assets/pdf/framemaker/pan-os/NewFeaturesGuide.pdf page 14

QUESTION NO: 26 Which Security Policy rule configuration option disables antivirus and anti-spyware scanning of server-to-client flows only? A. Apply an Application Override Policy B. Disable Server Response Inspection C. Add server IP to Security Policy exception D. Disable HIP Profile Answer: B Reference: https://www.paloaltonetworks.com/documentation/61/pan-os/pan-os/gettingstarted/set-up-basic-security-policies.html

QUESTION NO: 27 Which two interface types provide support for network address translation (NAT)? Choose 2 answers A. HA B. Tap C. Layer3 D. Virtual Wire E. Layer2 Answer: C,D Reference: https://live.paloaltonetworks.com/servlet/JiveServlet/previewBody/1517-102-711647/Understanding_NAT-4.1-RevC.pdf

QUESTION NO: 28 A firewall is being attacked with a port scan. Which component can prevent this attack?

www.braindumps.com

19

Palo Alto Networks PCNSE6 Exam A. DoS Protection B. Anti-Spyware C. Vulnerability Protection D. Zone Protection Answer: D Reference: https://live.paloaltonetworks.com/docs/DOC-4501

QUESTION NO: 29 A Palo Alto Networks firewall has the following interface configuration;

Hosts are directly connected on the following interfaces: Ethernet 1/6 - Host IP 192.168.62.2 Ethernet 1/3 - Host IP 10.46.40.63 The security administrator is investigating why ICMP traffic between the hosts is not working. She first ensures that ail traffic is allowed between zones based on the following security policy rule:

The routing table of the firewall shows the following output:

www.braindumps.com

20

Palo Alto Networks PCNSE6 Exam

Which interface configuration change should be applied to ethernet1/6 to allow the two hosts to communicate based on this information? A. Change the Management Profile. B. Change the security policy to explicitly allow ICMP on this interface. C. Change the configured zone to DMZ. D. Change the Virtual Router setting to VR1. Answer: D Explanation:

QUESTION NO: 30 HOTSPOT Match the components with their role in preventing threats. Answer options may be used more than once or not at all.

www.braindumps.com

21

Palo Alto Networks PCNSE6 Exam

Answer:

Explanation: Panorama – Dynamically updates firewall policy with VM context for NSX Physical Firewall – Inspects North-South traffic for threats Wildfire –Generates zero-day threat signatures VM series firewall- Inspects east-west traffic for threats

www.braindumps.com

22

Palo Alto Networks PCNSE6 Exam

QUESTION NO: 31 After migrating from an ASA firewall, the VPN connection between a remote network and the Palo Alto Networks firewall is not establishing correctly. The following entry is appearing in the logs: pfs group mismatched: my:0 peer:2 Which setting should be changed on the Palo Alto Firewall to resolve this error message? A. Update the IPSEC Crypto profile for the Vendor IPSec Tunnel from group2 to no-pfs. B. Update the IKE Crypto profile for the Vendor IKE gateway from no-pfs to group2. C. Update the IPSEC Crypto profile for the Vendor IPSec Tunnel from no-pfs to group2. D. Update the IKE Crypto profile for the Vendor IKE gateway from group2 to no-pfs. Answer: C Reference: https://www.paloaltonetworks.com/documentation/61/pan-os/pan-os/vpns/interpretvpn-error-messages.html

QUESTION NO: 32 Which two interface types can be used when configuring GlobalProtect Portal? Choose 2 answers A. Virtual Wire B. Loopback C. Tunnel D. Layer3 Answer: B,D Reference: https://www.paloaltonetworks.com/content/dam/paloaltonetworkscom/en_US/assets/pdf/framemaker/61/globalprotect/globalprotect-admin-guide.pdf page 10

QUESTION NO: 33

www.braindumps.com

23

Palo Alto Networks PCNSE6 Exam After pushing a security policy from Panorama to a PA-3020 firewall, the firewall administrator notices that traffic logs from the PA-3020 are not appearing in Panorama's traffic logs. What could be the problem? A. The firewall is not licensed for logging to this Panorama device. B. Panorama is not licensed to receive logs from this particular firewall. C. None of the firewall’s policies have been assigned a Log Forwarding profile. D. A Server Profile has not been configured for logging to this Panorama device. Answer: C Explanation:

QUESTION NO: 34 Palo Alto Networks maintains a dynamic database of malicious domains. Which two Security Platform components use this database to prevent threats? Choose 2 answers A. Brute-force signatures B. DNS-based command-and-control signatures C. PAN-DB URL Filtering D. BrightCloud URL Filtering Answer: B,C Reference: https://www.paloaltonetworks.com/products/features/apt-prevention.html

QUESTION NO: 35 Which three inspections can be performed with a next-generation firewall but NOT with a legacy firewall? Choose 3 answers A. Recognizing when SSH sessions are using SSH v1 instead of SSH v2 B. Validating that UDP port 53 packets are not being used to tunnel data for another protocol C. Identifying unauthorized applications that attempt to connect over non-standard ports D. Allowing a packet through from an external DNS server only if an internal host recently queried that DNS server E. Removing from the session table any TCP session without traffic for 3600 seconds Answer: B,C,D www.braindumps.com

24

Palo Alto Networks PCNSE6 Exam Explanation:

QUESTION NO: 36 Which mechanism is used to trigger a High Availability (HA) failover if a firewall interface goes down? A. Link Monitoring B. Heartbeat Polling C. Preemption D. SNMP Polling Answer: A Reference: https://www.paloaltonetworks.com/content/dam/paloaltonetworkscom/en_US/assets/pdf/framemaker/60/pan-os/pan-os/section_4.pdf page 130

QUESTION NO: 37 HOTSPOT Match the description of an application field with its name. Answer options may be used more than once or not at all.

www.braindumps.com

25

Palo Alto Networks PCNSE6 Exam Answer:

Explanation: A TCP three-way handshake completed successfully but the firewall does not have an appropriate App-ID signature – unknown-tcp A TCP handshake completed successfully, but only one more packet was sent – not enough to identify the application – insufficient-data Data received has been discarded because it matched an explicit “deny” rule for that traffic – notapplicable A TCP three-way handshake die NOT complete OR no additional data was sent after a successful TCP three-way handshake – incomplete UDP data has been received but the firewall does not have an appropriate App-ID signature – unknown-udp. Reference: https://live.paloaltonetworks.com/docs/DOC-1549

QUESTION NO: 38 How is the Forward Untrust Certificate used? A. It issues certificates encountered on the Untrust security zone. B. It is used for Captive Portal to identify unknown users. C. It is used when web servers request a client certificate. D. It is the issuer for an external certificate which is not trusted by the firewall. Answer: D Explanation: www.braindumps.com

26

Palo Alto Networks PCNSE6 Exam

QUESTION NO: 39 By default, all PA-5060 syslog data is forwarded out the Management interface. What needs to be configured in order to send syslog data out of a different interface? A. Configure Service Route Only for Threats and URL Filtering, and the traffic will use the same route. B. Configure an Interface Management Profile and apply it to the interface that the syslogs will be sent through. C. Configure a Service Route for the Syslog service to use a dataplane interface. D. Create a Log-Forwarding Profile that points to the device that will receive the syslogs. Answer: C Reference: https://www.paloaltonetworks.com/documentation/60/pan-os/pan-os/reports-andlogging/define-remote-logging-destinations.html

QUESTION NO: 40 A network administrator uses Panorama to push security policies to managed firewalls at branch offices. Which policy type should be configured on Panorama if the administrator wishes to allow local administrators at the branch office sites to override these policies? A. Implicit Rules B. Post Rules C. Default Rules D. Pre Rules Answer: D Explanation:

QUESTION NO: 41 A network engineer experienced network reachability problems through the firewall. The routing table on the device is complex. To troubleshoot the problem the engineer ran a Command Line www.braindumps.com

27

Palo Alto Networks PCNSE6 Exam Interface (CLI) command to determine the egress interface for traffic destined to 98.139.183.24. The command resulted in the following output:

How should this output be interpreted? A. There is no route for the IP address 98.139.183.24, and there is a default route for outbound traffic. B. There is no interface in the firewall with the IP address 98.139.183.24. C. In virtual-router vrl, there is a route in the routing table for the network 98.139.0.0/16. D. There is no route for the IP address 98.139.183.24, and there is no default route. Answer: D Explanation:

QUESTION NO: 42 A website is presenting an RSA 2048-bit key. By default, what will the size of the key in the certificate sent by the firewall to the client be when doing SSL Decryption? A. 512 bits B. 1024 bits C. 2048 bits D. 4096 bits Answer: C Reference: https://www.paloaltonetworks.com/documentation/61/panos/newfeaturesguide/management-features/configurable-key-size-for-ssl-forward-proxy-servercertificates.html

QUESTION NO: 43 A hotel chain is using a system to centrally control a variety of items in guest rooms. The client www.braindumps.com

28

Palo Alto Networks PCNSE6 Exam devices in each guest room communicate to the central controller using TCP and frequently disconnect due to a premature timeouts when going through a Palo Alto Networks firewall. Which action will address this issue without affecting all TCP traffic traversing the firewall? A. Create a security policy without security profiles, allowing the client-to-server traffic. B. Create an application override policy, assigning the client-to-server traffic to a custom application. C. Create an application with a specified TCP timeout and assign traffic to it with an application override policy. D. Create an application override policy, assigning the server-to-client traffic to a custom application. Answer: C Explanation:

QUESTION NO: 44 Ethernet 1/1 has been configured with the following subinterfaces:

The following security policy is applied:

The Interface Management Profile permits the following:

www.braindumps.com

29

Palo Alto Networks PCNSE6 Exam

Your customer is trying to ping 10.10.10.1 from VLAN 800 IP 10.10.10.2/24 What will be the result of this ping? A. The ping will be successful because the management profile applied to Ethernet1/1 allows ping. B. The ping will not be successful because the virtual router is different from the other subinterfaces. C. The ping will not be successful because there is no management profile attached to Ethernet1/1.799. D. The ping will not be successful because the security policy does not apply to VLAN 800. E. The ping will be successful because the security policy permits this traffic. Answer: D Explanation:

QUESTION NO: 45 What are the three Security Policy rule Type classifications supported in PAN-OS 6.1? A. Security, NAT, Policy-Based Forwarding

www.braindumps.com

30

Palo Alto Networks PCNSE6 Exam B. Intrazone, Interzone, Global C. Intrazone, Interzone, Universal D. Application, User, Content Answer: C Reference: https://www.paloaltonetworks.com/content/dam/paloaltonetworkscom/en_US/assets/pdf/framemaker/61/pan-os/NewFeaturesGuide.pdf page 18-19

QUESTION NO: 46 Which two steps are required to make Microsoft Active Directory users appear in the firewall’s traffic log? Choose 2 answers A. Enable User-ID on the zone object for the source zone. B. Enable User-ID on the zone object for the destination zone. C. Configure a RADIUS server profile to point to a domain controller. D. Run the User-ID Agent using an Active Directory account that has "domain administrator" permissions. E. Run the User-ID Agent using an Active Directory account that has "event log viewer" permissions. Answer: A,E Explanation:

QUESTION NO: 47 It is discovered that WebandNetTrends Unlimited’s new web server software produces traffic that the Palo Alto Networks firewall sees as "unknown-tcp" traffic. Which two configurations would identify the application while preserving the ability of the firewall to perform content and threat detection on the traffic? Choose 2 answers A. A custom application, with a name properly describing the new web server s purpose B. A custom application and an application override policy that assigns traffic going to and from the web server to the custom application C. An application override policy that assigns the new web server traffic to the built-in application "web-browsing" D. A custom application with content and threat detection enabled, which includes a signature, identifying the new web server s traffic

www.braindumps.com

31

Palo Alto Networks PCNSE6 Exam Answer: A,B Explanation:

QUESTION NO: 48 The IT department has received complaints about VoIP call jitter when the sales staff is making or receiving calls. QoS is enabled on all firewall interfaces, but there is no QoS policy written in the rulebase. The IT manager wants to find out what traffic is causing the jitter in real time when a user reports the jitter. Which feature can be used to identify, in real-time, the applications taking up the most bandwidth? A. Application Command Center (ACC) B. QoS Statistics C. QoS Log D. Applications Report Answer: A Reference: http://www.newnet66.org/Support/Resources/Using-The-ACC.pdf

QUESTION NO: 49 A company has a web server behind their Palo Alto Networks firewall that they would like to make accessible to the public. They have decided to configure a destination NAT Policy rule. Given the following zone information: -

DMZzone: DMZ-L3 Public zone: Untrust-L3 Web server zone: Trust-L3 Public IP address (Untrust-L3): 1.1.1.1 Private IP address (Trust-L3): 192.168.1.50

What should be configured as the destination zone on the Original Packet tab of the NAT Policy rule? A. DMZ-L3 B. Any C. Untrust-L3 D. Trust-L3 www.braindumps.com

32

Palo Alto Networks PCNSE6 Exam Answer: C Explanation:

QUESTION NO: 50 Which URL Filtering Security Profile action logs the URL Filtering category to the URL Filtering log? A. Allow B. Alert C. Log D. Default Answer: B Reference: https://www.paloaltonetworks.com/documentation/61/pan-os/pan-os/urlfiltering/configure-url-filtering.html

QUESTION NO: 51 Where in the firewall GUI can an administrator see how many sessions of web-browsing traffic have occurred in the last day? A. Monitor->Session Browser B. Monitor->App Scope->Summary C. Objects->Applications->web-browsing D. ACC->Application Answer: D Reference: http://www.newnet66.org/Support/Resources/Using-The-ACC.pdf

QUESTION NO: 52 The WildFire Cloud or WF-500 appliance provide information to which two Palo Alto Networks security services? Choose 2 answers A. Threat Prevention www.braindumps.com

33

Palo Alto Networks PCNSE6 Exam B. App-ID C. URL Filtering D. PAN-OS E. GlobalProtect Data File Answer: A,E Reference: https://www.paloaltonetworks.com/products/technologies/wildfire.html

QUESTION NO: 53 A Palo Alto Networks firewall is being targeted by an NTP Amplification attack and is being flooded with tens of thousands of bogus UDP connections per second to a single destination IP address and port. Which option, when enabled with the correct threshold, would mitigate this attack without dropping legitimate traffic to other hosts inside the network? A. Zone Protection Policy with UDP Flood Protection B. Classified DoS Protection Policy using destination IP only with a Protect action C. QoS Policy to throttle traffic below maximum limit D. Security Policy rule to deny traffic to the IP address and port that is under attack Answer: B Reference: https://live.paloaltonetworks.com/docs/DOC-1746

QUESTION NO: 54 Which three processor types are found on the data plane of a PA-5050? Choose 3 answers A. Multi-Core Security Processor B. Signature Match Processor C. Network Processor D. Protocol Decoder Processor E. Management Processor Answer: A,B,C Reference: https://www.paloaltonetworks.com/content/dam/paloaltonetworkscom/en_US/assets/pdf/white-papers/single-pass-parallel-processing-architecture.pdf page 8

www.braindumps.com

34

Palo Alto Networks PCNSE6 Exam

QUESTION NO: 55 A firewall administrator is troubleshooting problems with traffic passing through the Palo Alto Networks firewall. Which method will show the global counters associated with the traffic after configuring the appropriate packet filters? A. From the CLI, issue the show counter interface command for the egress interface. B. From the GUI, select "Show global counters" under the Monitor tab. C. From the CLI, issue the show counter global filter packet-filter yes command. D. From the CLI, issue the show counter interface command for the ingress interface. Answer: C Reference: https://live.paloaltonetworks.com/docs/DOC-7971

QUESTION NO: 56 In the following display, ethernetl/6 is configured with an interface management profile that allows ping with no restriction on the source address:

Given the following security policy rule base:

What is the result of a ping sent from an address on the Trust-L3 zone to the IP address of ethernet1/6? A. The firewall will send an ICMP redirect message to the client.

www.braindumps.com

35

Palo Alto Networks PCNSE6 Exam B. The client will receive an ICMP "destination unreachable" packet. C. The interface will respond. D. The traffic will be dropped by the firewall. Answer: D Explanation:

QUESTION NO: 57 A security architect has been asked to implement User-ID in a MacOS environment with no enterprise email, using a Sun LDAP server for user authentication. In this environment, which two User-ID methods are effective for mapping users to IP addresses? Choose 2 answers A. Terminal Server Agent B. Mac OS Agent C. Captive Portal D. GlobalProtect Answer: C,D Explanation:

QUESTION NO: 58 Which feature can be configured with an IPv6 address? A. Static Route B. RIPv2 C. DHCP Server D. BGP Answer: A Reference: https://live.paloaltonetworks.com/docs/DOC-5493

QUESTION NO: 59

www.braindumps.com

36

Palo Alto Networks PCNSE6 Exam A company wants to run their pair of PA-200 firewalls in a High Availability Active/Passive configuration and will be using HA-Lite. Which capability can be used in this situation? A. Configuration Sync B. Link Aggregation C. Session Sync D. Jumbo Frames Answer: A Reference: https://live.paloaltonetworks.com/docs/DOC-3091

QUESTION NO: 60 HOTSPOT A company has a Palo Alto Networks firewall with a single VSYS that has both locally defined rules as well as shared and device-group rules pushed from Panorama. In what order are the policies evaluated?

www.braindumps.com

37

Palo Alto Networks PCNSE6 Exam

Answer: www.braindumps.com

38

Palo Alto Networks PCNSE6 Exam

Explanation: 1st: Shared Pre Rules 2nd: Device Group Pre Rules www.braindumps.com

39

Palo Alto Networks PCNSE6 Exam 3rd: Firewall Local Rules 4th: Device Group Post Rules 5th Shared Post Rules Reference: https://live.paloaltonetworks.com/docs/DOC-8842

www.braindumps.com

40

Test - Accredited Configuration Engineer (ACE) Exam - PAN-OS 7.0 Version ACE Exam

Question 1 of 50. User-ID is enabled in the configuration of … A Security Policy. A Zone. An Interface. A Security Profile. Mark for follow up

Question 2 of 50. What are the benefits gained when the "Enable Passive DNS Monitoring" checkbox is chosen on the firewall? (Select all correct answers.) Improved malware detection in WildFire. Improved PAN-DB malware detection. Improved DNS-based C&C signatures. Improved BrightCloud malware detection. Mark for follow up

Question 3 of 50. WildFire analyzes files to determine whether or not they are malicious. When doing so, WildFire will classify the file with an official verdict. This verdict is known as the WildFire Analysis verdict. Choose the three correct classifications as a result of this analysis and classification? Grayware Adware Benign Spyware Malware detection Safeware Mark for follow up

Question 4 of 50. In which of the following can User-ID be used to provide a match condition? Security Policies NAT Policies Zone Protection Policies Threat Profiles Mark for follow up

Question 5 of 50. What is the default setting for 'Action' in a Decryption Policy's rule? Any No-Decrypt Decrypt None Mark for follow up

Question 6 of 50. Which of the following CANNOT use the source user as a match criterion? QoS Secuirty Policies Policy Based Forwarding DoS Protection Anti-virus Profile

Mark for follow up

Question 7 of 50. Which of the Dynamic Updates listed below are issued on a daily basis? (Select all correct answers.) Applications and Threats Applications BrightCloud URL Filtering Anti-virus Mark for follow up

Question 8 of 50. WildFire may be used for identifying which of the following types of traffic? OSPF RIPv2 DHCP Malware Mark for follow up

Question 9 of 50. Which of the following platforms supports the Decryption Port Mirror function? PA-3000 VM-Series 100 PA-2000 PA-4000 Mark for follow up

Question 10 of 50. Color-coded tags can be used on all of the items listed below EXCEPT: Service Groups Zones Address Objects Vulnerability Profiles Mark for follow up

Question 11 of 50.

Taking into account only the information in the screenshot above, answer the following question. An administrator is using SSH on port 3333 and BitTorrent on port 7777. Which statements are True? The SSH traffic will be denied. The BitTorrent traffic will be denied. The SSH traffic will be allowed. The BitTorrent traffic will be allowed. Mark for follow up

Question 12 of 50. Which of the following facts about dynamic updates is correct? Application and Threat updates are released daily. Anti-virus and URL Filtering updates are released weekly.

Application and Anti-virus updates are released weekly. Threat and “Threat and URL Filtering” updates are released weekly. Threat and URL Filtering updates are released daily. Application and Anti-virus updates are released weekly. Anti-virus updates are released daily. Application and Threat updates are released weekly. Mark for follow up

Question 13 of 50. An interface in tap mode can transmit packets on the wire. True False Mark for follow up

Question 14 of 50. What is the default DNS sinkhole address used by the Palo Alto Networks Firewall to cut off communication? The MGT interface address. The default gateway of the firewall. Any layer 3 interface address specified by the firewall administrator. The local loopback address. Mark for follow up

Question 15 of 50. When using remote authentication for users (LDAP, RADIUS, Active Directory, etc.), what must be done to allow a user to authenticate through multiple methods? This cannot be done. A single user can only use one authentication type. This cannot be done. Although multiple authentication methods exist, a firewall must choose a single, global authentication type--and all users must use this method. Create multiple authentication profiles for the same user. Create an Authentication Sequence, dictating the order of authentication profiles. Mark for follow up

Question 16 of 50. Using the API in PAN-OS 6.1, WildFire subscribers can upload up to how many samples per day? 10 500 1000 50 Mark for follow up

Question 17 of 50. In Palo Alto Networks terms, an application is: A specific program detected within an identified stream that can be detected, monitored, and/or blocked. A combination of port and protocol that can be detected, monitored, and/or blocked. A file installed on a local machine that can be detected, monitored, and/or blocked. Web-based traffic from a specific IP address that can be detected, monitored, and/or blocked. Mark for follow up

Question 18 of 50. True or False: The WildFire Analysis Profile can only be configured to send unknown files to the WildFire Public Cloud only. True False Mark for follow up

Question 19 of 50. Traffic going to a public IP address is being translated by a Palo Alto Networks firewall to an internal server’s private IP address. Which IP address should the Security Policy use as the "Destination IP" in order to allow traffic to the server? The firewall’s gateway IP The server’s private IP The server’s public IP The firewall’s MGT IP

Mark for follow up

Question 20 of 50. The "Drive-By Download" protection feature, under File Blocking profiles in Content-ID, provides: Increased speed on downloads of file types that are explicitly enabled. The ability to use Authentication Profiles, in order to protect against unwanted downloads. Protection against unwanted downloads by showing the user a response page indicating that a file is going to be downloaded. Password-protected access to specific file downloads for authorized users. Mark for follow up

Question 21 of 50. An enterprise PKI system is required to deploy SSL Forward Proxy decryption capabilities. True False Mark for follow up

Question 22 of 50. Which of the following would be a reason to use the PAN-OS XML API to communicate with a Palo Alto Networks firewall? To permit syslogging of User Identification events. To allow the firewall to push User-ID information to a Network Access Control (NAC) device. To pull information from other network resources for User-ID. Mark for follow up

Question 23 of 50. Can multiple administrator accounts be configured on a single firewall? Yes No Mark for follow up

Question 24 of 50. What will be the user experience when the safe search option is NOT enabled for Google search but the firewall has "Safe Search Enforcement" Enabled? A task bar pop-up message will be presented to enable Safe Search. The user will be redirected to a different search site that is specified by the firewall administrator. A block page will be presented with instructions on how to set the strict Safe Search option for the Google search. The Firewall will enforce Safe Search if the URL filtering license is still valid. Mark for follow up

Question 25 of 50. Will an exported configuration contain Management Interface settings? Yes No Mark for follow up

Question 26 of 50. Choose the best answer: In PAN-OS, the WildFire Subscription Service allows updates for malware signatures to be distributed as often as… Once a day Once an hour Once every 15 minutes Once a week Mark for follow up

Question 27 of 50. Enabling "Highlight Unused Rules" in the Security Policy window will: Display rules that caused a validation error to occur at the time a Commit was performed. Temporarily disable rules that have not matched traffic since the rule was created or since the last reboot of the firewall. Highlight all rules that did not match traffic within an administrator-specified time period.

Highlight all rules that have not matched traffic since the rule was created or since the last reboot of the firewall.

Mark for follow up

Question 28 of 50. Besides selecting the Heartbeat Backup option when creating an Active-Passive HA Pair, which of the following also prevents "Split-Brain"? Under “Packet Forwarding”, selecting the VR Sync checkbox. Configuring a backup HA2 link that points to the MGT interface of the other device in the pair. Creating a custom interface under Service Route Configuration, and assigning this interface as the backup HA2 link. Configuring an independent backup HA1 link. Mark for follow up

Question 29 of 50. You can assign an IP address to an interface in Virtual Wire mode. True False Mark for follow up

Question 30 of 50. In order to route traffic between Layer 3 interfaces on the Palo Alto Networks firewall, you need a: Virtual Router VLAN Virtual Wire Security Profile Mark for follow up

Question 31 of 50. As of PAN-OS 7.0, when configuring a Decryption Policy Rule, which of the following is NOT an available option as matching criteria in the rule? Source Zone URL Category Source User Service Application Mark for follow up

Question 32 of 50. When you have created a Security Policy Rule that allows Facebook, what must you do to block all other web-browsing traffic? Ensure that the Service column is defined as "application-default" for this Security policy. Doing this will automatically include the implicit web-browsing application dependency. Create an additional rule that blocks all other traffic. When creating the policy, ensure that web-browsing is included in the same rule. Nothing. You can depend on PAN-OS to block the web-browsing traffic that is not needed for Facebook use. Mark for follow up

Question 33 of 50.

Taking into account only the information in the screenshot above, answer the following question. An administrator is pinging 4.4.4.4 and fails to receive a response. What is the most likely reason for the lack of response? There is no Management Profile. The interface is down. There is a Security Policy that prevents ping. There is no route back to the machine originating the ping. Mark for follow up

Question 34 of 50. Which type of license is required to perform Decryption Port Mirroring? A Client Decryption license A free PAN-PA-Decrypt license A subscription-based SSL Port license A subscription-based PAN-PA-Decrypt license Mark for follow up

Question 35 of 50. When troubleshooting Phase 1 of an IPsec VPN tunnel, which location and log will be most informative? Initiating side, System log Responding side, System Log Responding side, Traffic log Initiating side, Traffic log Mark for follow up

Question 36 of 50. Users may be authenticated sequentially to multiple authentication servers by configuring: A custom Administrator Profile. An Authentication Sequence. An Authentication Profile. Multiple RADIUS servers sharing a VSA configuration. Mark for follow up

Question 37 of 50. After the installation of the Threat Prevention license, the firewall must be rebooted. True False Mark for follow up

Question 38 of 50. As a Palo Alto Networks firewall administrator, you have made unwanted changes to the Candidate configuration. These changes may be undone by Device > Setup > Operations > Configuration Management>....and then what operation? Revert to Running Configuration Revert to last Saved Configuration Load Configuration Version Import Named Configuration Snapshot

Mark for follow up

Question 39 of 50. Which of the following must be enabled in order for User-ID to function? Security Policies must have the User-ID option enabled. User-ID must be enabled for the source zone of the traffic that is to be identified. Captive Portal must be enabled. Captive Portal Policies must be enabled. Mark for follow up

Question 40 of 50. When configuring a Decryption Policy rule, which option allows a firewall administrator to control SSHv2 tunneling in policies by specifying the SSH-tunnel App-ID? SSH Proxy SSL Forward Proxy SSL Inbound Inspection SSL Reverse Proxy Mark for follow up

Question 41 of 50.

The screenshot above shows part of a firewall’s configuration. If ping traffic can traverse this device from e1/2 to e1/1, which of the following statements must be True about this firewall’s configuration? (Select all correct answers.) There must be a Management Profile that allows ping. (Then assign that Management Profile to e1/1 and e1/2.) There must be a security policy rule from trust zone to Internet zone that allows ping. There must be appropriate routes in the default virtual router. There must be a security policy rule from Internet zone to trust zone that allows ping. Mark for follow up

Question 42 of 50. A Config Lock may be removed by which of the following users? (Select all correct answers.) Any administrator The administrator who set it Superusers Device administrators Mark for follow up

Question 43 of 50. Without a WildFire subscription, which of the following files can be submitted by the Firewall to the hosted WildFire virtualized sandbox? PE and Java Applet (jar and class) only PE files only PDF files only MS Office doc/docx, xls/xlsx, and ppt/pptx files only Mark for follow up

Question 44 of 50. Which statement about config locks is True? A config lock will expire after 24 hours, unless it was set by a superuser. A config lock can be removed only by the administrator who set it. A config lock can be removed only by a superuser. A config lock can only be removed by the administrator who set it or by a superuser. Mark for follow up

Question 45 of 50. Which of the following can provide information to a Palo Alto Networks firewall for the purposes of User-ID? (Select all correct answers.) Domain Controller SSL Certificates RIPv2 Network Access Control (NAC) device Mark for follow up

Question 46 of 50. A "Continue" action can be configured on which of the following Security Profiles? URL Filtering and File Blocking URL Filtering only URL Filtering, File Blocking, and Data Filtering URL Filtering and Anti-virus Mark for follow up

Question 47 of 50. All of the interfaces on a Palo Alto Networks device must be of the same interface type. True False Mark for follow up

Question 48 of 50. An interface in Virtual Wire mode must be assigned an IP address. True False Mark for follow up

Question 49 of 50. What is the maximum file size of .EXE files uploaded from the firewall to WildFire? Always 10 megabytes. Always 2 megabytes. Configurable up to 2 megabytes. Configurable up to 10 megabytes. Mark for follow up

Question 50 of 50.

Taking into account only the information in the screenshot above, answer the following question: A span port or a switch is connected to e1/4, but there are no traffic logs. Which of the following conditions most likely explains this behavior? The interface is not assigned an IP address. The interface is not up. The interface is not assigned a virtual router. There is no zone assigned to the interface. Mark for follow up

Save / Return Later

Summary

4/7/2015

Empowering People: paloaltonetworks

Test ­ Accredited Configuration Engineer (ACE) Exam ­ PAN­OS 6.1 Version ACE Exam 

Question 1 of 50.  The following can be configured as a next hop in a static route:   A Policy­Based Forwarding Rule   Virtual Systems   Virtual Router   Virtual Switch     Mark for follow up

Question 2 of 50.  As a Palo Alto Networks firewall administrator, you have made unwanted changes to the Candidate configuration. These changes may be undone by Device > Setup > Operations > Configuration Management>....and then what operation?   Revert to Running Configuration   Revert to last Saved Configuration   Load Configuration Version   Import Named Configuration Snapshot     Mark for follow up

Question 3 of 50.  Which statement below is True?   PAN­OS uses BrightCloud for URL Filtering, replacing PAN­DB.   PAN­OS uses BrightCloud as its default URL Filtering database, but also supports PAN­DB.   PAN­OS uses PAN­DB as the default URL Filtering database, but also supports BrightCloud.   PAN­OS uses PAN­DB for URL Filtering, replacing BrightCloud.     Mark for follow up

Question 4 of 50.  When employing the BrightCloud URL filtering database in a Palo Alto Networks firewall, the order of evaluation within a profile is:   Block list, Custom Categories, Predefined categories, Dynamic URL filtering, Allow list, Cache files.   Block list, Allow list, Custom Categories, Cache files, Local URL DB file.   Block list, Custom Categories, Cache files, Predefined categories, Dynamic URL filtering, Allow list.   Dynamic URL filtering, Block list, Allow list, Cache files, Custom categories, Predefined categories.     Mark for follow up

Question 5 of 50.  With IKE Phase 1, each device is identified to the other by a Peer ID. In most cases, the Peer ID is just the public IP address of the device. In situations where the public IP address is not static, the Peer ID can be a text value. True False       Mark for follow up

Question 6 of 50. 

The screenshot above shows part of a firewall’s configuration. If ping traffic can traverse this device from e1/2 to e1/1, which of the following statements must be True about this firewall’s configuration? (Select all correct answers.) There must be a security policy from Internet zone to trust zone that allows ping.   There must be a security policy from trust zone to Internet zone that allows ping.   There must be appropriate routes in the default virtual router.   There must be a Management Profile that allows ping. (Then assign that Management Profile to e1/1 and e1/2.)  

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?loid=1d91785b-4c5f-4aad-8994-b323d6d076a1&evalLvl=5&redirect_url=%2fphnx%2fdriver.…

1/7

4/7/2015

Empowering People: paloaltonetworks

    Mark for follow up

Question 7 of 50.  Which feature can be configured to block sessions that the firewall cannot decrypt?   Decryption Profile in Security Policy   Decryption Profile in Decryption Policy   Decryption Profile in PBF   Decryption Profile in Security Profile     Mark for follow up

Question 8 of 50.  All of the interfaces on a Palo Alto Networks device must be of the same interface type. True False       Mark for follow up

Question 9 of 50.  Which of the following would be a reason to use the PAN­OS XML API to communicate with a Palo Alto Networks firewall?   To permit syslogging of User Identification events.   To pull information from other network resources for User­ID.   To allow the firewall to push User­ID information to a Network Access Control (NAC) device.     Mark for follow up

Question 10 of 50.  Which of the following statements is NOT True about Palo Alto Networks firewalls?   Initial configuration may be accomplished thru the MGT interface or the Console port.   The default Admin account may be disabled or deleted.   By default the MGT Port's IP Address is 192.168.1.1/24.   System defaults may be restored by performing a factory reset in Maintenance Mode.     Mark for follow up

Question 11 of 50.  After the installation of a new version of PAN­OS, the firewall must be rebooted. True False       Mark for follow up

Question 12 of 50.  Which of the Dynamic Updates listed below are issued on a daily basis? (Select all correct answers.) BrightCloud URL Filtering   Applications and Threats   Applications   Anti­virus       Mark for follow up

Question 13 of 50.  Color­coded tags can be used on all of the items listed below EXCEPT:   Address Objects   Service Groups   Zones   Vulnerability Profiles     Mark for follow up

Question 14 of 50.  In a Palo Alto Networks firewall, every interface in use must be assigned to a zone in order to process traffic. True False  

 

 

Mark for follow up

Question 15 of 50.  You can assign an IP address to an interface in Virtual Wire mode. True False       Mark for follow up

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?loid=1d91785b-4c5f-4aad-8994-b323d6d076a1&evalLvl=5&redirect_url=%2fphnx%2fdriver.…

2/7

4/7/2015

Empowering People: paloaltonetworks

Question 16 of 50.  In order to route traffic between Layer 3 interfaces on the Palo Alto Networks firewall, you need a:   Virtual Router   VLAN   Virtual Wire   Security Profile     Mark for follow up

Question 17 of 50.  An interface in tap mode can transmit packets on the wire. True False       Mark for follow up

Question 18 of 50.  When Destination Network Address Translation is being performed, the destination in the corresponding Security Policy Rule should use:   The Post­NAT destination zone and Post­NAT IP address.   The Pre­NAT destination zone and Pre­NAT IP address.   The Pre­NAT destination zone and Post­NAT IP address.   The Post­NAT destination zone and Pre­NAT IP address.     Mark for follow up

Question 19 of 50. 

Taking into account only the information in the screenshot above, answer the following question. Which applications will be allowed on their standard ports? (Select all correct answers.) BitTorrent   Gnutella   Skype   SSH       Mark for follow up

Question 20 of 50.  When configuring a Security Policy Rule based on FQDN Address Objects, which of the following statements is True?   In order to create FQDN­based objects, you need to manually define a list of associated IP addresses.   The firewall resolves the FQDN first when the policy is committed, and resolves the FQDN again each time Security Profiles are evaluated.   The firewall resolves the FQDN first when the policy is committed, and resolves the FQDN again at DNS TTL expiration.     Mark for follow up

Question 21 of 50.  Users may be authenticated sequentially to multiple authentication servers by configuring:   An Authentication Sequence.   Multiple RADIUS servers sharing a VSA configuration.   A custom Administrator Profile.   An Authentication Profile.     Mark for follow up

Question 22 of 50.  Will an exported configuration contain Management Interface settings? Yes No       Mark for follow up

Question 23 of 50.  When using Config Audit, the color yellow indicates which of the following?  

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?loid=1d91785b-4c5f-4aad-8994-b323d6d076a1&evalLvl=5&redirect_url=%2fphnx%2fdriver.…

3/7

4/7/2015

Empowering People: paloaltonetworks

A setting has been changed between the two config files   A setting has been deleted from a config file.   A setting has been added to a config file   An invalid value has been used in a config file.     Mark for follow up

Question 24 of 50.  When using remote authentication for users (LDAP, RADIUS, Active Directory, etc.), what must be done to allow a user to authenticate through multiple methods?   Create an Authentication Sequence, dictating the order of authentication profiles.   Create multiple authentication profiles for the same user.   This cannot be done. A single user can only use one authentication type.   This cannot be done. Although multiple authentication methods exist, a firewall must choose a single, global authentication type­­and all users must use this method.     Mark for follow up

Question 25 of 50.  When troubleshooting Phase 1 of an IPsec VPN tunnel, which location and log will be most informative?   Responding side, System Log   Initiating side, Traffic log   Initiating side, System log   Responding side, Traffic log     Mark for follow up

Question 26 of 50.  User­ID is enabled in the configuration of …   A Zone.   A Security Profile.   An Interface.   A Security Policy.     Mark for follow up

Question 27 of 50.  What will the user experience when attempting to access a blocked hacking website through a translation service such as Google Translate or Bing Translator?   A “Blocked” page response when the URL filtering policy to block is enforced.   A “Success” page response when the site is successfully translated.   The browser will be redirected to the original website address.   An "HTTP Error 503 ­ Service unavailable" message.     Mark for follow up

Question 28 of 50.  When you have created a Security Policy Rule that allows Facebook, what must you do to block all other web­browsing traffic?   Nothing. You can depend on PAN­OS to block the web­browsing traffic that is not needed for Facebook use.   Ensure that the Service column is defined as "application­default" for this Security policy. Doing this will automatically include the implicit web­browsing application dependency.   Create an additional rule that blocks all other traffic.   When creating the policy, ensure that web­browsing is included in the same rule.     Mark for follow up

Question 29 of 50.  Both SSL decryption and SSH decryption are disabled by default. True False       Mark for follow up

Question 30 of 50.  A "Continue" action can be configured on which of the following Security Profiles?   URL Filtering and File Blocking   URL Filtering only   URL Filtering, File Blocking, and Data Filtering   URL Filtering and Anti­virus     Mark for follow up

Question 31 of 50.  Which of the following interface types can have an IP address assigned to it?

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?loid=1d91785b-4c5f-4aad-8994-b323d6d076a1&evalLvl=5&redirect_url=%2fphnx%2fdriver.…

4/7

4/7/2015

Empowering People: paloaltonetworks

  Layer 3   Layer 2   Tap   Virtual Wire     Mark for follow up

Question 32 of 50.  What are the benefits gained when the "Enable Passive DNS Monitoring" checkbox is chosen on the firewall? (Select all correct answers.) Improved DNS­based C&C signatures.   Improved PAN­DB malware detection.   Improved BrightCloud malware detection.   Improved malware detection in WildFire.       Mark for follow up

Question 33 of 50.  Security policies specify a source interface and a destination interface. True False       Mark for follow up

Question 34 of 50. 

Taking into account only the information in the screenshot above, answer the following question. An administrator is using SSH on port 3333 and BitTorrent on port 7777. Which statements are True? The SSH traffic will be denied.   The BitTorrent traffic will be allowed.   The SSH traffic will be allowed.   The BitTorrent traffic will be denied.       Mark for follow up

Question 35 of 50.  Which of the following most accurately describes Dynamic IP in a Source NAT configuration?   A single IP address is used, and the source port number is unchanged.   The next available IP address in the configured pool is used, but the source port number is unchanged.   A single IP address is used, and the source port number is changed.   The next available address in the configured pool is used, and the source port number is changed.     Mark for follow up

Question 36 of 50.  What are two sources of information for determining whether the firewall has been successful in communicating with an external User­ID Agent?   System Logs and Authentication Logs.   System Logs and the indicator light under the User­ID Agent settings in the firewall.   System Logs and an indicator light on the chassis.   Traffic Logs and Authentication Logs.     Mark for follow up

Question 37 of 50.  Which pre­defined Admin Role has all rights except the rights to create administrative accounts and virtual systems?   Superuser   Device Administrator   A custom admin role must be created for this specific combination of rights.   vsysadmin     Mark for follow up

Question 38 of 50.  An enterprise PKI system is required to deploy SSL Forward Proxy decryption capabilities.

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?loid=1d91785b-4c5f-4aad-8994-b323d6d076a1&evalLvl=5&redirect_url=%2fphnx%2fdriver.…

5/7

4/7/2015

Empowering People: paloaltonetworks

True False       Mark for follow up

Question 39 of 50. 

Taking into account only the information in the screenshot above, answer the following question: A span port or a switch is connected to e1/4, but there are no traffic logs. Which of the following conditions most likely explains this behavior?   The interface is not up.   There is no zone assigned to the interface.   The interface is not assigned an IP address.   The interface is not assigned a virtual router.     Mark for follow up

Question 40 of 50.  Which type of license is required to perform Decryption Port Mirroring?   A subscription­based SSL Port license   A free PAN­PA­Decrypt license   A Client Decryption license   A subscription­based PAN­PA­Decrypt license     Mark for follow up

Question 41 of 50.  Can multiple administrator accounts be configured on a single firewall? Yes No       Mark for follow up

Question 42 of 50.  Which of the following CANNOT use the source user as a match criterion?   DoS Protection   Secuirty Policies   Anti­virus Profile   Policy Based Forwarding   QoS     Mark for follow up

Question 43 of 50.  Which of the following must be enabled in order for User­ID to function?   Captive Portal Policies must be enabled.   User­ID must be enabled for the source zone of the traffic that is to be identified.   Captive Portal must be enabled.   Security Policies must have the User­ID option enabled.     Mark for follow up

Question 44 of 50.  In a Destination NAT configuration, the Translated Address field may be populated with either an IP address or an Address Object. True False       Mark for follow up

Question 45 of 50.  When configuring the firewall for User­ID, what is the maximum number of Domain Controllers that can be configured?  

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?loid=1d91785b-4c5f-4aad-8994-b323d6d076a1&evalLvl=5&redirect_url=%2fphnx%2fdriver.…

6/7

4/7/2015

Empowering People: paloaltonetworks

50   100   10   150     Mark for follow up

Question 46 of 50.  Besides selecting the Heartbeat Backup option when creating an Active­Passive HA Pair, which of the following also prevents "Split­Brain"?   Creating a custom interface under Service Route Configuration, and assigning this interface as the backup HA2 link.   Configuring an independent backup HA1 link.   Configuring a backup HA2 link that points to the MGT interface of the other device in the pair.   Under “Packet Forwarding”, selecting the VR Sync checkbox.     Mark for follow up

Question 47 of 50.  Palo Alto Networks firewalls support the use of both Dynamic (built­in user roles) and Role­Based (customized user roles) for Administrator Accounts. True False       Mark for follow up

Question 48 of 50.  When configuring a Decryption Policy rule, which option allows a firewall administrator to control SSHv2 tunneling in policies by specifying the SSH­tunnel App­ID?   SSH Proxy   SSL Forward Proxy   SSL Inbound Inspection   SSL Reverse Proxy     Mark for follow up

Question 49 of 50.  In which of the following can User­ID be used to provide a match condition? (Select all correct answers.)   Security Policies   NAT Policies   Zone Protection Policies   Threat Profiles     Mark for follow up

Question 50 of 50.  In PAN­OS 6.0, rule numbers are:   Numbers that specify the order in which security policies are evaluated.   Numbers created to be unique identifiers in each firewall’s policy database.   Numbers on a scale of 0 to 99 that specify priorities when two or more rules are in conflict.   Numbers created to make it easier for users to discuss a complicated or difficult sequence of rules.     Mark for follow up

Save / Return Later

Summary

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?loid=1d91785b-4c5f-4aad-8994-b323d6d076a1&evalLvl=5&redirect_url=%2fphnx%2fdriver.…

7/7

1Which of the following would be a reason to use the PAN-OS XML API to communicate with a Palo Alto Networks firewall? To pull info from other NW resources for USER-ID

2After the installation of a new version of PAN-OS, the firewall must be rebooted. True

3The "Disable Server Response Inspection" option on a Security Profile… Internal Trusted Server

4Which pre-defined Admin Role has all rights except the rights to create administrative accounts and virtual systems? Device Admin

5Which of the following statements is NOT True about Palo Alto Networks firewalls? The Admin account may be disabled

6In Palo Alto Networks terms, an application is: A specific program detected within an identified stream that can be detected, monitored and/or blocked

7Palo Alto Networks firewalls support the use of both Dynamic (built-in user roles) and Role-Based (customized user roles) for Administrator Accounts. True

8When employing the BrightCloud URL filtering database in a Palo Alto Networks firewall, the order of evaluation within a profile is: Block list, Allow list, Custom Cat, Cache files, Loc URL DB

9When configuring Admin Roles for Web UI access, what are the available access levels? Enable, RO & Disable

10What general practice best describes how Palo Alto Networks firewall policies are applied to a session? First match applied

11Which of the following is NOT a valid option for built-in CLI Admin roles? Read/Write

12Can multiple administrator accounts be configured on a single firewall? Yes

13Which of the following CANNOT use the source user as a match criterion? AV profile

14When configuring the firewall for User-ID, what is the maximum number of Domain Controllers that can be configured? 100

15After the installation of the Threat Prevention license, the firewall must be rebooted. False

16In which of the following can User-ID be used to provide a match condition? (Select all correct answers.) Sec Policies

17What is the function of the GlobalProtect Portal? To maintain list of Glob Prot GWs & specify HIP data that the agent should report

18When configuring User-ID on a Palo Alto Networks firewall, what is the proper procedure to limit User mappings to a particular DHCP scope? In the Zone in which UID is enabled, create a UID ACL Include list using same IP ranges as allocated in DHCP scope

19A "Continue" action can be configured on which of the following Security Profiles? URL filtering & File Blocking

20What will the user experience when attempting to access a blocked hacking website through a translation service such as Google Translate or Bing Translator? A Blocked page response when the URL filt policy to block is enf

21Traffic going to a public IP address is being translated by a Palo Alto Networks firewall to an internal server’s private IP address. Which IP address should the Security Policy use as the "Destination IP" in order to allow traffic to the server? The Server's Pub IP

22Which of the following facts about dynamic updates is correct? AV daily. App & Threat updates weekly

23What is the default DNS sinkhole address used by the Palo Alto Networks Firewall to cut off communication? Local Loop add

24When you have created a Security Policy Rule that allows Facebook, what must you do to block all other web-browsing traffic? Nothing

25Which of the following are necessary components of a GlobalProtect solution? GP GW , GP Agent, GP Portal

26-

Taking into account only the information in the screenshot above, answer the following question. Which applications will be allowed on their standard ports? (Select all correct answers.) SSH & BitTorrent

27Which of the following platforms supports the Decryption Port Mirror function? PA-3000

28When Destination Network Address Translation is being performed, the destination in the corresponding Security Policy Rule should use: Post-NAT Dest zone & Post-NAT IP 29In PAN-OS 6.0 and later, which of these items may be used as match criterion in a Policy-Based Forwarding Rule? (Choose 3.) Source User, Source Zone, App 30Which type of license is required to perform Decryption Port Mirroring? Free PAN-PA decrypt 31An interface in tap mode can transmit packets on the wire. False 32Which of the following interface types can have an IP address assigned to it? (Select all correct answers.) L3 33Which statement about config locks is True? Admin who set it OR SuperUser 34Which routing protocol is supported on the Palo Alto Networks platform? BGP RIPv2 35Which link is used by an Active/Passive cluster to synchronize session information? Data Link 36Which of the following must be enabled in order for User-ID to function? UID must be enabled for Src zone of the traffic that is to be identified 37Which of the following most accurately describes Dynamic IP in a Source NAT configuration? Next available IP in the configured pool is used but Src port unchanged

38A Config Lock may be removed by which of the following users? (Select all correct answers.) The Admin who set it & SuperUser 39Select the implicit rules that are applied to traffic that fails to match any administrator-defined Security Policies. (Choose all rules that are correct.) Intra-zone allowed Inter-zone denied 40Enabling "Highlight Unused Rules" in the Security Policy window will: High all rules that have not matched traffic since Rule was created or last Reboot of FW 41Which statement below is True? PAN-OS uses PAN-DB as Def URL filt DB but supports BrightCloud 42Both SSL decryption and SSH decryption are disabled by default. True 43When configuring a Security Policy Rule based on FQDN Address Objects, which of the following statements is True? The FW resolves FQDN when the policy is committed & resolves the FQDN again each time again at DNS TTL expiration 44In a Destination NAT configuration, the Translated Address field may be populated with either an IP address or an Address Object. True 45Security policies specify a source interface and a destination interface. False 46When configuring a Decryption Policy Rule, which of the following are available as matching criteria in the rule? (Choose 3 answers.) Source User Source Zone URL cat

47When troubleshooting Phase 1 of an IPsec VPN tunnel, which location and log will be most informative? Responding side System log 48“What is the result of an Administrator submitting a WildFire report’s verdict back to Palo Alto Networks as “Incorrect”? The sig will be updated for False + & F- files in next AV sig update 49An enterprise PKI system is required to deploy SSL Forward Proxy decryption capabilities. False 50Without a WildFire subscription, which of the following files can be submitted by the Firewall to the hosted WildFire virtualized sandbox? PE files only 51Which of the following statements is NOT True about Palo Alto Networks firewalls? The Admin account may be disabled 52In PAN-OS 6.0, rule numbers are: Numbers that specify the order in which sec pol are evaluated 53In a Palo Alto Networks firewall, every interface in use must be assigned to a zone in order to process traffic. True 54Reconnaissance Protection is a feature used to protect the Palo Alto Networks firewall from port scans. To enable this feature within the GUI go to… Nw-NW prof-Zone protection 55Using the API in PAN-OS 6.0, WildFire subscribers can upload up to how many samples per day? 100 56All of the interfaces on a Palo Alto Networks device must be of the same interface type. False

57The "Drive-By Download" protection feature, under File Blocking profiles in Content-ID, provides: Protection against unwanted dnlds by showing user response pg indic file is dnlding 58Color-coded tags can be used on all of the items listed below EXCEPT: Vulnerability profs 59Will an exported configuration contain Management Interface settings? Yes 60-

Taking into account only the information in the screenshot above, answer the following question. An administrator is using SSH on port 3333 and BitTorrent on port 7777. Which statements are True? SSH denied BitTorrent allowed

61When using Config Audit, the color yellow indicates which of the following? A setting has been changed between 2 config files

62-

As the Palo Alto Networks Administrator responsible for User-ID, you need to enable mapping of network users that do not sign-in using LDAP. Which information source would allow for reliable User-ID mapping while requiring the least effort to configure? Exchange CAS sec logs

63The following can be configured as a next hop in a static route:

Virtual Router

64Which of the following options may be enabled to reduce heavy server load conditions when using ContentID? DSRI 65What are two sources of information for determining whether the firewall has been successful in communicating with an external User-ID Agent? Sys Logs & Indicator light under UID agent settings in the FW 66As the Palo Alto Networks Administrator you have enabled Application Block pages. Afterwards, not knowing they are attempting to access a blocked web-based application, users call the Help Desk to complain about network connectivity issues. What is the cause of the increased number of help desk calls? The FW admin didn’t create custom response pg to notify potential users that their attempt to access the Web –based app is blocked due to policy 67After the installation of a new Application and Threat database, the firewall must be rebooted. False 68-

Taking into account only the information in the screenshot above, answer the following question. Which applications will be allowed on their standard ports? (Select all correct answers.) SSH & BitTorrent

69An interface in Virtual Wire mode must be assigned an IP address.

False

70What is the maximum file size of .EXE files uploaded from the firewall to WildFire? Configurable upto 10 MB 71Which feature can be configured to block sessions that the firewall cannot decrypt? Decryp Prof in Decryp Pol 72Which of the following search engines are supported by the "Safe Search Enforcement" option? (Select all correct answers.) Yahoo Google Bing 73Which of the following statements is NOT True regarding a Decryption Mirror interface? Can be a member of any Vsys 74Which mode will allow a user to choose when they wish to connect to the Global Protect Network? On demand mode 75-

Which of the following describes the sequence of the GlobalProtect Agent connecting to a GlobalProtect Gateway? Fastest SSL response time

76Which of the following are methods that HA clusters use to identify network outages?

Path & Link monitoring

77Which of the following is True of an application filter? An application filter automatically includes a new application when one of the new application’s characteristics are included in the filter.

78When configuring a Decryption Policy rule, which option allows a firewall administrator to control SSHv2 tunneling in policies by specifying the SSH-tunnel App-ID? SSH proxy

79In order to route traffic between Layer 3 interfaces on the Palo Alto Networks firewall, you need a: Virtual Router

80What will be the user experience when the safe search option is NOT enabled for Google search but the firewall has "Safe Search Enforcement" Enabled?

A block page will be presented with instructions on how to set strict Safe Search for Google.

81User-ID is enabled in the configuration of … A Zone

1/20/2015

Empowering People: paloaltonetworks

Test ­ Accredited Configuration Engineer (ACE) Exam ­ PAN­OS 6.0 Version ACE Exam 

Question 1 of 50.  Which of the following statements is NOT True regarding a Decryption Mirror interface?   Supports SSL outbound   Supports SSL inbound   Can be a member of any VSYS   Requires superuser privilege     Mark for follow up

Question 2 of 50.  How do you reduce the amount of information recorded in the URL Content Filtering Logs?   Enable "Log container page only".   Disable URL packet captures.   Enable URL log caching.   Enable DSRI.     Mark for follow up

Question 3 of 50.  Which routing protocol is supported on the Palo Alto Networks platform?   BGP   RIPv1   ISIS   RSTP     Mark for follow up

Question 4 of 50.  When using remote authentication for users (LDAP, RADIUS, Active Directory, etc.), what must be done to allow a user to authenticate through multiple methods?   Create multiple authentication profiles for the same user.   This cannot be done. A single user can only use one authentication type.   Create an Authentication Sequence, dictating the order of authentication profiles.   This cannot be done. Although multiple authentication methods exist, a firewall must choose a single, global authentication type­­and all users must use this method.   https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?loid=7557e253­1f91­470f­a91c­a284f048d2c3&evalLvl=5&redirect_url=%2fphnx%2fdriver.as…

1/12

1/20/2015

Empowering People: paloaltonetworks

  Mark for follow up

Question 5 of 50.  In a Destination NAT configuration, the Translated Address field may be populated with either an IP address or an Address Object. True False  

 

 

Mark for follow up

Question 6 of 50.  Which of the following CANNOT use the source user as a match criterion?   DoS Protection   Secuirty Policies   QoS   Anti­virus Profile   Policy Based Forwarding     Mark for follow up

Question 7 of 50.  A Config Lock may be removed by which of the following users? (Select all correct answers.) Device administrators   Any administrator   The administrator who set it   Superusers       Mark for follow up

Question 8 of 50. 

Taking into account only the information in the screenshot above, answer the following question. An administrator is using SSH on port 3333 and BitTorrent on port 7777. Which statements are True? The BitTorrent traffic will be denied.   https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?loid=7557e253­1f91­470f­a91c­a284f048d2c3&evalLvl=5&redirect_url=%2fphnx%2fdriver.as…

2/12

1/20/2015

Empowering People: paloaltonetworks

The SSH traffic will be allowed.   The BitTorrent traffic will be allowed.   The SSH traffic will be denied.       Mark for follow up

Question 9 of 50.  With IKE Phase 1, each device is identified to the other by a Peer ID. In most cases, the Peer ID is just the public IP address of the device. In situations where the public IP address is not static, the Peer ID can be a text value. True False  

 

 

Mark for follow up

Question 10 of 50.  What Security Profile type must be configured to send files to the WildFire cloud, and with what choices for the action setting?   A Data Filtering profile with possible actions of “Forward” or “Continue and Forward”.   A Vulnerability Protection profile with the possible action of “Forward”.   A File Blocking profile with possible actions of “Forward” or “Continue and Forward”.   A URL Filtering profile with the possible action of “Forward”.     Mark for follow up

Question 11 of 50.  Both SSL decryption and SSH decryption are disabled by default. True False  

 

 

Mark for follow up

Question 12 of 50.  Which of the following would be a reason to use the PAN­OS XML API to communicate with a Palo Alto Networks firewall?   To permit syslogging of User Identification events.   To pull information from other network resources for User­ID.   To allow the firewall to push User­ID information to a Network Access Control (NAC) device.     Mark for follow up

Question 13 of 50.  Without a WildFire subscription, which of the following files can be submitted by the Firewall to the hosted WildFire virtualized sandbox?   MS Office doc/docx, xls/xlsx, and ppt/pptx files only   https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?loid=7557e253­1f91­470f­a91c­a284f048d2c3&evalLvl=5&redirect_url=%2fphnx%2fdriver.as…

3/12

1/20/2015

Empowering People: paloaltonetworks

PE and Java Applet (jar and class) only   PE files only   PDF files only     Mark for follow up

Question 14 of 50.  What is the function of the GlobalProtect Portal?   To maintain the list of Global Protect Gateways and specify HIP data that the agent should report.   To load­balance GlobalProtect client connections to GlobalProtect Gateways.   To maintain the list of remote GlobalProtect Portals and the list of categories for checking the client machine.   To provide redundancy for tunneled connections through the GlobalProtect Gateways.     Mark for follow up

Question 15 of 50.  Which of the following interface types can have an IP address assigned to it? (Select all correct answers.)   Layer 3   Layer 2   Tap   Virtual Wire     Mark for follow up

Question 16 of 50.  Which of the following most accurately describes Dynamic IP in a Source NAT configuration?   The next available address in the configured pool is used, and the source port number is changed.   A single IP address is used, and the source port number is unchanged.   A single IP address is used, and the source port number is changed.   The next available IP address in the configured pool is used, but the source port number is unchanged.     Mark for follow up

Question 17 of 50.  WildFire may be used for identifying which of the following types of traffic?   RIPv2   DHCP   OSPF   Malware     https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?loid=7557e253­1f91­470f­a91c­a284f048d2c3&evalLvl=5&redirect_url=%2fphnx%2fdriver.as…

4/12

1/20/2015

Empowering People: paloaltonetworks

Mark for follow up

Question 18 of 50.  Which link is used by an Active/Passive cluster to synchronize session information?   The Uplink   The Control Link   The Management Link   The Data Link     Mark for follow up

Question 19 of 50.  Users may be authenticated sequentially to multiple authentication servers by configuring:   Multiple RADIUS servers sharing a VSA configuration.   A custom Administrator Profile.   An Authentication Sequence.   An Authentication Profile.     Mark for follow up

Question 20 of 50.  Which statement about config locks is True?   A config lock can be removed only by a superuser.   A config lock will expire after 24 hours, unless it was set by a superuser.   A config lock can only be removed by the administrator who set it or by a superuser.   A config lock can be removed only by the administrator who set it.     Mark for follow up

Question 21 of 50.  Which feature can be configured to block sessions that the firewall cannot decrypt?   Decryption Profile in Security Profile   Decryption Profile in PBF   Decryption Profile in Decryption Policy   Decryption Profile in Security Policy     Mark for follow up

Question 22 of 50.  All of the interfaces on a Palo Alto Networks device must be of the same interface type. https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?loid=7557e253­1f91­470f­a91c­a284f048d2c3&evalLvl=5&redirect_url=%2fphnx%2fdriver.as…

5/12

1/20/2015

True  

Empowering People: paloaltonetworks

False  

 

Mark for follow up

Question 23 of 50.  As the Palo Alto Networks Administrator you have enabled Application Block pages. Afterwards, not knowing they are attempting to access a blocked web­based application, users call the Help Desk to complain about network connectivity issues. What is the cause of the increased number of help desk calls?   Some App­ID's are set with a Session Timeout value that is too low.   Application Block Pages will only be displayed when Captive Portal is configured.   The firewall admin did not create a custom response page to notify potential users that their attempt to access the web­ based application is being blocked due to policy.   The File Blocking Block Page was disabled.     Mark for follow up

Question 24 of 50.  When configuring a Decryption Policy rule, which option allows a firewall administrator to control SSHv2 tunneling in policies by specifying the SSH­tunnel App­ID?   SSH Proxy   SSL Forward Proxy   SSL Inbound Inspection   SSL Reverse Proxy     Mark for follow up

Question 25 of 50.  What is the default DNS sinkhole address used by the Palo Alto Networks Firewall to cut off communication?   Any layer 3 interface address specified by the firewall administrator.   The MGT interface address.   The local loopback address.   The default gateway of the firewall.     Mark for follow up

Question 26 of 50. 

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?loid=7557e253­1f91­470f­a91c­a284f048d2c3&evalLvl=5&redirect_url=%2fphnx%2fdriver.as…

6/12

1/20/2015

Empowering People: paloaltonetworks

Considering the information in the screenshot above, what is the order of evaluation for this URL Filtering Profile?   Block List, Allow List, URL Categories (BrightCloud or PAN­DB), Custom Categories.   Allow List, Block List, Custom Categories, URL Categories (BrightCloud or PAN­DB).   Block List, Allow List, Custom Categories, URL Categories (BrightCloud or PAN­DB).   URL Categories (BrightCloud or PAN­DB), Custom Categories, Block List, Allow List.     Mark for follow up

Question 27 of 50.  Security policies specify a source interface and a destination interface. True False  

 

 

Mark for follow up

Question 28 of 50.  Enabling "Highlight Unused Rules" in the Security Policy window will:   Highlight all rules that did not match traffic within an administrator­specified time period.   Highlight all rules that have not matched traffic since the rule was created or since the last reboot of the firewall.   Display rules that caused a validation error to occur at the time a Commit was performed.   Temporarily disable rules that have not matched traffic since the rule was created or since the last reboot of the firewall.     https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?loid=7557e253­1f91­470f­a91c­a284f048d2c3&evalLvl=5&redirect_url=%2fphnx%2fdriver.as…

7/12

1/20/2015

Empowering People: paloaltonetworks

Mark for follow up

Question 29 of 50.  When troubleshooting Phase 1 of an IPsec VPN tunnel, which location and log will be most informative?   Responding side, Traffic log   Responding side, System Log   Initiating side, Traffic log   Initiating side, System log     Mark for follow up

Question 30 of 50.  In PAN­OS 6.0, rule numbers are:   Numbers that specify the order in which security policies are evaluated.   Numbers created to be unique identifiers in each firewall’s policy database.   Numbers on a scale of 0 to 99 that specify priorities when two or more rules are in conflict.   Numbers created to make it easier for users to discuss a complicated or difficult sequence of rules.     Mark for follow up

Question 31 of 50.  When you have created a Security Policy Rule that allows Facebook, what must you do to block all other web­browsing traffic?   When creating the policy, ensure that web­browsing is included in the same rule.   Nothing. You can depend on PAN­OS to block the web­browsing traffic that is not needed for Facebook use.   Ensure that the Service column is defined as "application­default" for this Security policy. Doing this will automatically include the implicit web­browsing application dependency.   Create an additional rule that blocks all other traffic.     Mark for follow up

Question 32 of 50.  When using Config Audit, the color yellow indicates which of the following?   A setting has been changed between the two config files   A setting has been deleted from a config file.   A setting has been added to a config file   An invalid value has been used in a config file.     Mark for follow up

Question 33 of 50.  https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?loid=7557e253­1f91­470f­a91c­a284f048d2c3&evalLvl=5&redirect_url=%2fphnx%2fdriver.as…

8/12

1/20/2015

Empowering People: paloaltonetworks

Will an exported configuration contain Management Interface settings? Yes No  

 

 

Mark for follow up

Question 34 of 50.  An interface in tap mode can transmit packets on the wire. True False  

 

 

Mark for follow up

Question 35 of 50.  Which of the following is a routing protocol supported in a Palo Alto Networks firewall?   EIGRP   RIPv2   IGRP   ISIS     Mark for follow up

Question 36 of 50.  In Palo Alto Networks terms, an application is:   A specific program detected within an identified stream that can be detected, monitored, and/or blocked.   A combination of port and protocol that can be detected, monitored, and/or blocked.   A file installed on a local machine that can be detected, monitored, and/or blocked.   Web­based traffic from a specific IP address that can be detected, monitored, and/or blocked.     Mark for follow up

Question 37 of 50.  Reconnaissance Protection is a feature used to protect the Palo Alto Networks firewall from port scans. To enable this feature within the GUI go to…   Network > Network Profiles > Zone Protection   Objects > Zone Protection   Interfaces > Interface Number > Zone Protection   Policies > Profile > Zone Protection     Mark for follow up

Question 38 of 50.  Which of the following is NOT a valid option for built­in CLI Admin roles?   https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?loid=7557e253­1f91­470f­a91c­a284f048d2c3&evalLvl=5&redirect_url=%2fphnx%2fdriver.as…

9/12

1/20/2015

Empowering People: paloaltonetworks

deviceadmin   superuser   read/write   devicereader     Mark for follow up

Question 39 of 50.  In which of the following can User­ID be used to provide a match condition? (Select all correct answers.)   Security Policies   NAT Policies   Zone Protection Policies   Threat Profiles     Mark for follow up

Question 40 of 50.  A user complains that she is no longer able to access a needed work application after the administrator implemented vulnerability and anti­spyware profiles. How best can the administrator resolve this issue so the user will once again have access to the needed application?   In the vulnerability and anti­spyware Profiles, create an application exemption for the group’s application.   Check the Threat Log and locate an event showing the user’s application being blocked. Using the source IP address displayed in that event, create an IP address­based exemption for the group that the user is a member of.   Create a custom Security Policy for this user so that she will be able to access the required application. Be sure not to apply the vulnerability and anti­spyware profiles to this policy.   Create and enable an Application Override Policy, specifying the port used by this application.     Mark for follow up

Question 41 of 50.  An enterprise PKI system is required to deploy SSL Forward Proxy decryption capabilities. True False  

 

 

Mark for follow up

Question 42 of 50.  User­ID is enabled in the configuration of …   A Security Policy.   An Interface.   A Zone.   A Security Profile.    

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?loid=7557e253­1f91­470f­a91c­a284f048d2c3&evalLvl=5&redirect_url=%2fphnx%2fdriver.a…

10/12

1/20/2015

Empowering People: paloaltonetworks

Mark for follow up

Question 43 of 50.  What are the benefits gained when the "Enable Passive DNS Monitoring" checkbox is chosen on the firewall? (Select all correct answers.) Improved malware detection in WildFire.   Improved DNS­based C&C signatures.   Improved PAN­DB malware detection.   Improved BrightCloud malware detection.       Mark for follow up

Question 44 of 50.  Which of the following platforms supports the Decryption Port Mirror function?   PA­3000   VM­Series 100   PA­2000   PA­4000     Mark for follow up

Question 45 of 50.  “What is the result of an Administrator submitting a WildFire report’s verdict back to Palo Alto Networks as “Incorrect”?   You will receive an update within 15 minutes.   The signature will be updated for False positive and False negative files in the next AV signature update.   The signature will be updated for False positive and False negative files in the next Application signature update.   You will receive an email to disable the signature manually.     Mark for follow up

Question 46 of 50.  Which of the following facts about dynamic updates is correct?   Threat and URL Filtering updates are released daily. Application and Anti­virus updates are released weekly.   Anti­virus updates are released daily. Application and Threat updates are released weekly.   Application and Anti­virus updates are released weekly. Threat and “Threat and URL Filtering” updates are released weekly.   Application and Threat updates are released daily. Anti­virus and URL Filtering updates are released weekly.     Mark for follow up

Question 47 of 50.  https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?loid=7557e253­1f91­470f­a91c­a284f048d2c3&evalLvl=5&redirect_url=%2fphnx%2fdriver.a…

11/12

1/20/2015

Empowering People: paloaltonetworks

When configuring a Security Policy Rule based on FQDN Address Objects, which of the following statements is True?   The firewall resolves the FQDN first when the policy is committed, and resolves the FQDN again at DNS TTL expiration.   The firewall resolves the FQDN first when the policy is committed, and resolves the FQDN again each time Security Profiles are evaluated.   In order to create FQDN­based objects, you need to manually define a list of associated IP addresses.     Mark for follow up

Question 48 of 50.  What general practice best describes how Palo Alto Networks firewall policies are applied to a session?   The rule with the highest rule number is applied.   First match applied.   Last match applied.   Most specific match applied.     Mark for follow up

Question 49 of 50.  Which of the following statements is NOT True about Palo Alto Networks firewalls?   System defaults may be restored by performing a factory reset in Maintenance Mode.   The Admin account may be disabled.   Initial configuration may be accomplished thru the MGT interface or the Console port.   The Admin account may not be disabled.     Mark for follow up

Question 50 of 50.  When configuring User­ID on a Palo Alto Networks firewall, what is the proper procedure to limit User mappings to a particular DHCP scope?   In the zone in which User Identification is enabled, select the "Restrict Allocated IP" checkbox.   In the zone in which User Identification is enabled, create a User Identification ACL Include List using the same IP ranges as those allocated in the DHCP scope.   Under the User Identification settings, under the User Mapping tab, select the "Restrict Users to Allocated IP" checkbox.   In the DHCP settings on the Palo Alto Networks firewall, point the DHCP Relay to the IP address of the User­ID agent.     Mark for follow up

Save / Return Later

Summary

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?loid=7557e253­1f91­470f­a91c­a284f048d2c3&evalLvl=5&redirect_url=%2fphnx%2fdriver.a…

12/12

Realize Your Potential: paloaltonetworks

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?loid...

Test - Accredited Configuration Engineer (ACE) Exam - PAN-OS 7.0 Version ACE Exam

Question 1 of 50. Which routing protocol is supported on the Palo Alto Networks platform? BGP RIPv1 ISIS RSTP

Mark for follow up

Question 2 of 50. Which type of license is required to perform Decryption Port Mirroring? A free PAN-PA-Decrypt license A Client Decryption license A subscription-based PAN-PA-Decrypt license A subscription-based SSL Port license

Mark for follow up

Question 3 of 50. Which of the following is a routing protocol supported in a Palo Alto Networks firewall? RIPv2 ISIS IGRP EIGRP

Mark for follow up

Question 4 of 50. What is the maximum file size of .EXE files uploaded from the firewall to WildFire? Configurable up to 10 megabytes. Always 10 megabytes. Configurable up to 2 megabytes. Always 2 megabytes.

Mark for follow up

Question 5 of 50. WildFire analyzes files to determine whether or not they are malicious. When doing so, WildFire will classify the file with an official verdict. This verdict is known as the WildFire Analysis verdict. Choose the three correct classifications as a result of this analysis and classification? Benign Adware Spyware Malware detection Safeware Grayware

Mark for follow up

Question 6 of 50. What is the default setting for 'Action' in a Decryption Policy's rule? No-Decrypt Decrypt Any None

Mark for follow up

Question 7 of 50. When using Config Audit, the color yellow indicates which of the following? A setting has been changed between the two config files

1

7

21/12/2015 11:39

Realize Your Potential: paloaltonetworks

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?loid...

A setting has been deleted from a config file. A setting has been added to a config file An invalid value has been used in a config file.

Mark for follow up

Question 8 of 50. Select the implicit rules that are applied to traffic that fails to match any administrator-defined Security Policies. (Choose all rules that are correct.) Intra-zone traffic is allowed Inter-zone traffic is denied Intra-zone traffic is denied Inter-zone traffic is allowed

Mark for follow up

Question 9 of 50. Without a WildFire subscription, which of the following files can be submitted by the Firewall to the hosted WildFire virtualized sandbox? PE files only PDF files only MS Office doc/docx, xls/xlsx, and ppt/pptx files only PE and Java Applet (jar and class) only

Mark for follow up

Question 10 of 50. All of the interfaces on a Palo Alto Networks device must be of the same interface type. True

False

Mark for follow up

Question 11 of 50. In PAN-OS 6.0 and later, rule numbers are: Numbers that specify the order in which security policies are evaluated. Numbers created to be unique identifiers in each firewall’s policy database. Numbers on a scale of 0 to 99 that specify priorities when two or more rules are in conflict. Numbers created to make it easier for users to discuss a complicated or difficult sequence of rules.

Mark for follow up

Question 12 of 50. Using the API in PAN-OS 6.1, WildFire subscribers can upload up to how many samples per day? 500 50 1000 10

Mark for follow up

Question 13 of 50. Security policy rules specify a source interface and a destination interface. True

False

Mark for follow up

Question 14 of 50. Which feature can be configured to block sessions that the firewall cannot decrypt? Decryption Profile in Security Profile Decryption Profile in Security Policy Decryption Profile in Decryption Policy Decryption Profile in PBF

Mark for follow up

Question 15 of 50. Can multiple administrator accounts be configured on a single firewall? Yes

2

7

No

21/12/2015 11:39

Realize Your Potential: paloaltonetworks

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?loid...

Mark for follow up

Question 16 of 50. Which of the following services are enabled on the MGT interface by default? (Select all correct answers.) HTTPS SSH Telnet HTTP

Mark for follow up

Question 17 of 50. In a Palo Alto Networks firewall, every interface in use must be assigned to a zone in order to process traffic. True

False

Mark for follow up

Question 18 of 50. When you have created a Security Policy Rule that allows Facebook, what must you do to block all other web-browsing traffic? Create an additional rule that blocks all other traffic. Nothing. You can depend on PAN-OS to block the web-browsing traffic that is not needed for Facebook use. Ensure that the Service column is defined as "application-default" for this Security policy. Doing this will automatically include the implicit web-browsing application dependency. When creating the policy, ensure that web-browsing is included in the same rule.

Mark for follow up

Question 19 of 50.

Taking into account only the information in the screenshot above, answer the following question. Which applications will be allowed on their standard ports? (Select all correct answers.) BitTorrent SSH Gnutella Skype

Mark for follow up

Question 20 of 50. An interface in Virtual Wire mode must be assigned an IP address. True

False

Mark for follow up

Question 21 of 50. Traffic going to a public IP address is being translated by a Palo Alto Networks firewall to an internal server’s private IP address. Which IP address should the Security Policy use as the "Destination IP" in order to allow traffic to the server? The firewall’s gateway IP The server’s public IP The server’s private IP The firewall’s MGT IP

Mark for follow up

Question 22 of 50. What are two sources of information for determining whether the firewall has been successful in communicating with an external User-ID Agent? System Logs and Authentication Logs. System Logs and the indicator light under the User-ID Agent settings in the firewall. System Logs and an indicator light on the chassis. Traffic Logs and Authentication Logs.

3

7

21/12/2015 11:39

Realize Your Potential: paloaltonetworks

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?loid...

Mark for follow up

Question 23 of 50. An interface in tap mode can transmit packets on the wire. True

False

Mark for follow up

Question 24 of 50. User-ID is enabled in the configuration of … A Security Policy. A Zone. An Interface. A Security Profile.

Mark for follow up

Question 25 of 50. Users may be authenticated sequentially to multiple authentication servers by configuring: An Authentication Profile. An Authentication Sequence. A custom Administrator Profile. Multiple RADIUS servers sharing a VSA configuration.

Mark for follow up

Question 26 of 50. Which of the following most accurately describes Dynamic IP in a Source NAT configuration? The next available address in the configured pool is used, and the source port number is changed. The next available IP address in the configured pool is used, but the source port number is unchanged. A single IP address is used, and the source port number is unchanged. A single IP address is used, and the source port number is changed.

Mark for follow up

Question 27 of 50. WildFire may be used for identifying which of the following types of traffic? RIPv2 Malware DHCP OSPF

Mark for follow up

Question 28 of 50. Enabling "Highlight Unused Rules" in the Security Policy window will: Highlight all rules that did not match traffic within an administrator-specified time period. Highlight all rules that have not matched traffic since the rule was created or since the last reboot of the firewall. Temporarily disable rules that have not matched traffic since the rule was created or since the last reboot of the firewall. Display rules that caused a validation error to occur at the time a Commit was performed.

Mark for follow up

Question 29 of 50. When configuring a Security Policy Rule based on FQDN Address Objects, which of the following statements is True? The firewall resolves the FQDN first when the policy is committed, and resolves the FQDN again each time Security Profiles are evaluated. The firewall resolves the FQDN first when the policy is committed, and resolves the FQDN again at DNS TTL expiration. In order to create FQDN-based objects, you need to manually define a list of associated IP addresses.

Mark for follow up

Question 30 of 50. When configuring a Decryption Policy rule, which option allows a firewall administrator to control SSHv2 tunneling in policies by specifying the SSH-tunnel App-ID? SSH Proxy

4

7

21/12/2015 11:39

Realize Your Potential: paloaltonetworks

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?loid...

SSL Forward Proxy SSL Inbound Inspection SSL Reverse Proxy

Mark for follow up

Question 31 of 50. When using remote authentication for users (LDAP, RADIUS, Active Directory, etc.), what must be done to allow a user to authenticate through multiple methods? Create an Authentication Sequence, dictating the order of authentication profiles. This cannot be done. Although multiple authentication methods exist, a firewall must choose a single, global authentication type--and all users must use this method. Create multiple authentication profiles for the same user. This cannot be done. A single user can only use one authentication type.

Mark for follow up

Question 32 of 50. Which of the following is NOT a valid option for built-in CLI Admin roles? read/write deviceadmin devicereader superuser

Mark for follow up

Question 33 of 50. When Destination Network Address Translation is being performed, the destination in the corresponding Security Policy Rule should use: The Post-NAT destination zone and Pre-NAT IP addresses. The Pre-NAT destination zone and Post-NAT IP addresses. The Pre-NAT destination zone and Pre-NAT IP addresses. The Post-NAT destination zone and Post-NAT IP addresses.

Mark for follow up

Question 34 of 50. A "Continue" action can be configured on which of the following Security Profiles? URL Filtering and File Blocking URL Filtering only URL Filtering, File Blocking, and Data Filtering URL Filtering and Anti-virus

Mark for follow up

Question 35 of 50. When configuring Admin Roles for Web UI access, what are the available access levels? Enable, Read-Only, and Disable None, Superuser, Device Administrator Allow and Deny only Enable and Disable only

Mark for follow up

Question 36 of 50. Which of the following would be a reason to use the PAN-OS XML API to communicate with a Palo Alto Networks firewall? To allow the firewall to push User-ID information to a Network Access Control (NAC) device. To permit syslogging of User Identification events. To pull information from other network resources for User-ID.

Mark for follow up

Question 37 of 50. Previous to PAN-OS 7.0 the firewall was able to decode up to two levels. With PAN-OS 7.0 the firewall can now decode up to how many levels? Three Six Five Four

5

7

21/12/2015 11:39

Realize Your Potential: paloaltonetworks

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?loid...

Mark for follow up

Question 38 of 50. The "Drive-By Download" protection feature, under File Blocking profiles in Content-ID, provides: Increased speed on downloads of file types that are explicitly enabled. The ability to use Authentication Profiles, in order to protect against unwanted downloads. Password-protected access to specific file downloads for authorized users. Protection against unwanted downloads by showing the user a response page indicating that a file is going to be downloaded.

Mark for follow up

Question 39 of 50. In PAN-OS 6.0 and later, which of these items may be used as match criterion in a Policy-Based Forwarding Rule? (Choose 3.) Source Zone Destination Zone Source User Destination Application

Mark for follow up

Question 40 of 50. Both SSL decryption and SSH decryption are disabled by default. True

False

Mark for follow up

Question 41 of 50. You can assign an IP address to an interface in Virtual Wire mode. True

False

Mark for follow up

Question 42 of 50.

Taking into account only the information in the screenshot above, answer the following question. An administrator is pinging 4.4.4.4 and fails to receive a response. What is the most likely reason for the lack of response? There is no route back to the machine originating the ping. The interface is down. There is no Management Profile. There is a Security Policy that prevents ping.

Mark for follow up

Question 43 of 50. Which of the following is True of an application filter? An application filter automatically adapts when an application moves from one IP address to another. An application filter automatically includes a new application when one of the new application’s characteristics are included in the filter. An application filter specifies the users allowed to access an application. An application filter is used by malware to evade detection by firewalls and anti-virus software.

Mark for follow up

Question 44 of 50. In a Destination NAT configuration, the Translated Address field may be populated with either an IP address or an Address Object. True

6

7

False

21/12/2015 11:39

Realize Your Potential: paloaltonetworks

https://paloaltonetworks.csod.com/Evaluations/EvalLaunch.aspx?loid...

Mark for follow up

Question 45 of 50. In PAN-OS 7.0 which of the available choices serves as an alert warning by defining patterns of suspicious traffic and network anomalies that may indicate a host has been compromised? App-ID Signatures Correlation Objects Command & Control Signatures Correlation Events Custom Signatures

Mark for follow up

Question 46 of 50. Which statement below is True? PAN-OS uses PAN-DB as the default URL Filtering database, but also supports BrightCloud. PAN-OS uses BrightCloud as its default URL Filtering database, but also supports PAN-DB. PAN-OS uses BrightCloud for URL Filtering, replacing PAN-DB. PAN-OS uses PAN-DB for URL Filtering, replacing BrightCloud.

Mark for follow up

Question 47 of 50. Which of the following can provide information to a Palo Alto Networks firewall for the purposes of User-ID? (Select all correct answers.) Network Access Control (NAC) device Domain Controller RIPv2 SSL Certificates

Mark for follow up

Question 48 of 50. When employing the BrightCloud URL filtering database in a Palo Alto Networks firewall, the order of evaluation within a profile is: Block list, Allow list, Custom Categories, Cache files, Local URL DB file. Block list, Custom Categories, Cache files, Predefined categories, Dynamic URL filtering, Allow list. Dynamic URL filtering, Block list, Allow list, Cache files, Custom categories, Predefined categories. Block list, Custom Categories, Predefined categories, Dynamic URL filtering, Allow list, Cache files.

Mark for follow up

Question 49 of 50. As of PAN-OS 7.0, when configuring a Decryption Policy Rule, which of the following is NOT an available option as matching criteria in the rule? Application Source User URL Category Source Zone Service

Mark for follow up

Question 50 of 50. What will the user experience when attempting to access a blocked hacking website through a translation service such as Google Translate or Bing Translator? A “Blocked” page response when the URL filtering policy to block is enforced. A “Success” page response when the site is successfully translated. The browser will be redirected to the original website address. An "HTTP Error 503 - Service unavailable" message.

Mark for follow up

Save / Return Later

7

7

Summary

21/12/2015 11:39

View more...

Comments

Copyright ©2017 KUPDF Inc.
SUPPORT KUPDF