PA SOR Building Works and Sanitary Works

SOR Premable Page 1

1.

SCHEDULE OF RATES All work materials and goods described in this Schedule of Rates shall be of the respective kinds, described in the Contract and in accordance with the instructions of the Superintending Officer.

2.

The description given of each item, unless otherwise stated, be held to include the use of materials, labour, equipment, tools and vehicles including maintenance, supply of fuel and all idle time, conveyance, delivery, unloading, storing, hoisting, all labour setting, fitting, scaffolding and fixing in position, all cutting and waste, return of packings, establishment charges, overheads, profits and all forms of claims for loss and expense.

3.

Unless otherwise stated, all work shall be measured nett as fixed in its place.

4.

Unless otherwise stated, pipes are described by their internal diameters.

5.

The term “as specified” means as specified in the Standard Specifications, Supplementary Specifications and/or Drawings.

6.

The following abbreviations are used for the units:m m2 m3 no. ltr pc. kg ton pr sht hr

7.

-

Linear metre Square metre Cubic metre Number Litre Piece Kilogram Tonne Pair Sheet Hour

The Cost of removal and disposal and the making good of all affected works shall be deemed to be included in the Schedule of Rates unless otherwise stated. All Schedule of Rates shall be applicable for new and replacement works.

8.

1

All rates in the Schedule shall include all necessary materials and waste, plant, stagings and scaffoldings (only applicable up to 6m high, any height above 6 metres shall be paid separately, measuring from ground level, i.e. from the base for which scaffolding rests) unless specified otherwise.

SOR Premable Page 2 PARTICULAR PREAMBLES TO VARIOUS SECTIONS Part (A) - Excavation The measurement of all excavation and subsequent disposal shall be those before excavating. The increases in bulk and any extra excavation required for planking and strutting and formwork for concrete and working spaces under circumstances have been allowed for in the rates. Rates for each item shall be held to include for keeping all excavation free from water and Site dry pumping or bailing if required and providing any temporary drains required. Ordinary Ground Includes spoil or rubbish of every description, rubbish tip material etc., sand, gravel decomposed granite, red or white earth, loamy or gravelly clay, gravelly laterite, mud, bog or any other formation which. is removable by the ordinary application of pick and shovel and at any depth.

Part (B) - Concretor Unless otherwise specified in the Schedule of Rates :Rates for each item of concrete shall be held to include the followings :(1)

Forming, cutting groves, chases, mortice, holes and making good any other sundry items of a like nature.

(2)

Extra labour for laying to falls, or cambers and preparing surfaces to receive screeds or pavings also to be included.

(3)

All tests on concrete, cement and aggregate etc as required and compliance with the strengths as specified.

(4)

Tamping and/or vibrating to give thorough compaction; working between and around reinforcement.

(5)

Laying on any type of sub-base preparing and leaving surfaces to receive screeds or paving. Concrete in footpath and apron shall be treated as above ground level

No deduction shall be made in the measurement of concrete work for: (1) (2) (3)

Voids of 0.05 cubic metre or under. Volume of the reinforcement and steelwork. Openings in walls, floor, roof slabs and the like of 0.2 square metre or less.

Rates for mild steel or high tensile steel rod reinforcement shall be held to include for thoroughly wire brushing and cleaning all bars free of rust, dust, mill scale, dirt, oil, any other deleterious matter, cutting to the required lengths, bending and hooking and for securing with an including tying wires at all crossing, nondesigned spacers or chairs and distance blocks. No allowance shall be made for rolling margin in the measurement of rod reinforcements.

SOR Premable Page 3 PARTICULAR PREAMBLES TO VARIOUS SECTIONS (CONT’D) Part (B) – Concretor (Cont’d) The conversion factor for the various steel reinforcement bars shall be as follows: 6mm - 0.222kg/m 7mm - 0.302kg/m 8mm - 0.394kg/m 9mm - 0.499kg/m 10mm - 0.616kg/m 13mm - 1.042kg/m

16mm - 1.579kg/m 20mm - 2.466kg/m 22mm - 2.984kg/m 25mm - 3.854kg/m 28mm - 4.834kg/m 32mm - 6.313kg/m

Rates for each item of fabric reinforcement shall be held to include for extra material at laps, tying wires and all bending, cutting and notching around obstruction. Only the next area covered shall be measured and no deduction shall be made for opening less than 1.00 square metre. Rates for formwork shall be held to include for splayed edges, notchings, allowances for overlaps and passing at angles, battens, strutting, bolting, welding, easing, wetting and treating with mould oil, striking and removal. The rate in formwork allows for multiple uses where “multiple” means exceeding two. No deductions shall be made in measurement of formwork for: (1) (2) (3)

Openings less than 1 square metre. Intersection of main and secondary beams. Intersection of beams and stanchion casing or columns.

Rates for concrete, reinforcement and formwork shall be applicable to all work irrespective of positions, shapes and height Rates for each item of precast concrete shall be held to include for all necessary mould, finished faces, forming holes, rebates, sinking, mortices, recesses, hoisting and setting. The measurement of precast concrete vents and grilles shall be held to include for all angles, intersections, ends outlets and extra labour and material for forming grooves and rebates to sides. Piling work shall be executed in accordance with the relevant specifications and Superintending Officer’s instructions. Part (C) – Brick and Block Works Rates for each item of blockwork and facing shall be held to include for all special made blocks, bricks and insitu concrete in lieu, all holdfasts and bonding ties at abutments to concrete structures, all rough and fair cuttings, over-sailing and receding courses, rough relieving and discharging arches, wedging and pining, raking out joints for and pointing flashings, bedding plates, bedding and pointing of frames, parging and coring flues, labour eaves filing, plumbing angles forming square and rebated reveals, cut squiats or birdmouths, notches, forming, leaving or cutting chases, holes and morticles and cutting and pining and making good and any other sundry items of a like nature. Rates of blockwork and brickwork shall be applicable to all work irrespective of positions, shapes and height. Deductions shall be measured the nett sizes of the openings and recesses, including the extra width or rebated reveals. No deductions shall be made for voids not exceeding 0.10 square metre. Deductions shall be made for strings, sills, lintols and the like only when exceeding 75mm in height. Repair Work to External Walls to Prevent Rainwater Seepage.

SOR Premable Page 4 PARTICULAR PREAMBLES TO VARIOUS SECTIONS (CONT’D) Part (C) – Brick and Block Works (Cont’d) Daywork Should rates be applicable in respect of all work executed on a daywork basis. During the continuance of such work, the Contractor shall keep proper records of the names, occupations and working hours of all workmen employed for such work and the quantities and descriptions of all materials and plant employed. Such records, receipts or vouchers must be verified by the Superintending Officer before payment can be effected. Part (D) - Pavior Rates for each item of pavior shall be held to include for all rounded-edges on in-situ paving, all arises and making good and any other sundry items of a like nature. Rates for each item for skirtings, risers, moulded edges, channels and the like shall be held to include for all short lengths, formed, cut and purpose-made angle, junctions, end etc and making good and any other sundry item of a like nature. No deduction shall be made for a void of 0.50 square meter and under for in-situ paving. In the case of construction of interlocking concrete paving blocks and footpaths, the composite rates shall be applied, unless otherwise decided by the Superintending Officer. Part (E) - Roofer The description of each item of roofer shall be deemed to include: (1)

All laps, straight, skew and circular cutting at eaves, verges, top edges, abutments, valleys and hips, cutting holes for pipes, nails, screws, clips, pellets, straps and the like.

(2)

Chasing the structure for burning in or tucking in edges of coverings, flashing and the like.

(3)

Holes in coverings, underbeds and insulations for pipes, standards and the like and making good. No deduction shall be made for voids of 0.5m2 or less. Rates for Waterproofing Membranes and Secondary Roofing System shall be held to include for narrow widths, small quantities, temporary rules, covering up, protecting after laying and cleaning on completion, all labour to form arises, fair edges etc., all cuttings and working around pipes, dress down at eaves to form drips or carried up abutments to walls, pipes, parapets, skirtings, concrete curbs etc. and the like. The description of each item of profiled sheet roofing or cladding shall be deemed to include all cutting at square and raking abutments, top edges, bedding and pointing eaves fillers, verges, cutting, fitting and making good around outlets, pipes and any other sundry items of a like nature.

SOR Premable Page 5 PARTICULAR PREAMBLES TO VARIOUS SECTIONS (CONT’D) Part (F) – Carpenter, Joiner and Ironmonger Rates for each item of carpenter and joiner shall be held to include for cutting, notching, boring, sinking, pelleting, fitting, trimming, mitreing, halving, morticing, tenoning, devetailing, scarfing and wedging and for all ends, splayed edges, short lengths, nails, screw and temporary supports and any other sundry item of a like nature. Nominal sizes are stated for wrot timber and an allowance of 2.5mm is permitted for each wrot face. Rate for windows and doors include handing and fixing. Rates for each item of Ironmonger shall be held to include for supply, delivery to site and fixing complete with all matching screws of the same finish as ironmongery, nails, pins or brads, cutting, sinking and boring and morticing as required, oiling and easing and adjusting all moving parts, taking off and refixing after painting where necessary. All references to trade names shall include those which are approved to those as specified. Where ironmongery is included in the description of doors, it shall be deemed to include hinges, floor springs, door gears, locks, latches, catches, bolts, closers, holders, padlocks, stoppers, push-bars and plates, pull bars and handles, kick plates, locking eyes and the like as specified. Rates for Carpenter, Joiner and Ironmonger items shall be deemed to include removal where necessary unless otherwise stated, locks must include 2 keys properly labeled and handed to the Superintending Officer. Part (G) – Steel and Iron Worker Rates shall be held to include supply, delivery to site and fixing, cutting ends, welding, riveting, bolting etc. in addition, the rates for structural steel is deemed to also include for hoisting, erecting, temporary bracing, leveling and plumbing, and paint with one coat of primer. No allowance shall be made for rolling margin in the measurement of steelwork. No deduction shall be made for drilling, holes, notchings, splay cuts and the like. Where no conversion table is available from manufacturer/supplier, specific gravity of 7.5 (i.e. 7.5OgmIcm3) shall be used to compute the weight of mild steel sections. Part (H) – Plasterer and Wall Tiler Rates for each item of plastering shall be held to include for raking out joints, hacking to form keys, narrow width and small quantities, temporary rules, joints between new and old plastering, internal angles, arises, quirks, groin points and other intersections and curved surfaces, rounded coves and external angles not exceeding 25mm radius, and mitres, tops, etc. om cornices, mouldings, enrichments, coves, skirtings, gutters and strings, all making good and any other sundry item of a like nature. No deduction shall be made for openings of 0.50 square metre or less. In the measurement of plastering, no deduction shall be made for casings for pipes under 300mm wide or angles which are finished in a different material if these do not exceed 100mm girth. “Within the building” shall mean surfaces within the internal of buildings/flats, corridors, staircases and the lilce which normally do not entail scaffolding or mechanical cradles to carry out the works. “External face of building” shall mean surfaces such as gable end walls, front/back external walls and any other surfaces which are constantly exposed to weather and/or normally require the use of scaffolding or mechanical cradles to carry out the work.

SOR Premable Page 6 PARTICULAR PREAMBLES TO VARIOUS SECTIONS (CONT’D) Part (H) – Plasterer and Wall Tiler (Cont’d) Rates for each item of wall tiling shall be held to include for narrow widths and small quantities and fittings around air bricks, pipes and the like and any other sundry item. Rates for each item of terrazzo shall be held to include for narrow widths and small quantities, and for all temporary rules, internal angles, arises, joints between different types of terrazzo, quirks and making good and any other sundry items of a like nature on in-situ terrazzo fitting around air bricks, pipes and the like and any other sundry items of a like nature on precast terrazzo. Structural Repairs (The following is applicable for H029 — H03 1 only) The rate for each item shall be held to include for: (1)

Addition/Replacement of steel reinforcement in concrete components as directed by the Superintending Officer.

(2)

Removal of finishes/fixtures and other obstruction in the course of repair.

(3)

The removal of debris from the site in the process of repair or as directed by the Superintending Officer.

(4)

The cleaning up of site on completion.

(5)

Provision of barricadings, warning signs and warning lights.

(6)

Provision of props and formworks as directed by the Superintending Officer.

(7)

All general risks, liabilities and obligations set forth.

Part (I) - Glazier Rates for each item of glazier shall be held to include for cutting and rounded edges, puttying, fixing panel pins, brass screws and cup and neoprene strips where necessary and leaving the glass clean on completion. Part (J) - Painter Rates for each item of painting shall be held to include for all necessary preparation of surfaces including cleaning off, sandpapering woodwork, wire-brushing metal and leaving all surfaces free from dust, rust, grease and oil before painting, narrow widths, etc. Rates for painting include allowance for the use of different colours. No deduction shall be made for openings of 0.50 square metre or less. Part (K) – Roads and Carparks Rates for each item shall include cost of removal and cost of implementation of precautionary measures where necessary unless otherwise stated.

SOR Premable Page 7 PARTICULAR PREAMBLES TO VARIOUS SECTIONS (CONT’D) Part (L) - Dayworks The following rates shall be applicable to all works executed on a daywork basis including shifting of office equipment and furniture. During the continuance of such works, the Contractor shall keep proper records of the names, occupations and working hours of all workmen employed for such work and the quantities and descriptions of all materials and plant employed. Such records, receipts or vouchers must be verified by the Superintending Officer before payment can be effected. Provided always that if the Superintending Officer shall consider that for any reason the keeping of such records, receipts and vouchers by the Contractor as required was impracticable, he shall nevertheless be entitled to authorize payment for such works either as daywork (being satisfied as to the time employed and plant and materials used on such work) or at such value thereof as he shall consider fair and reasonable. Daywork’s Schedule of Rates for LABOUR and PLANTS items only (L00l to L034) is inclusive of 15% Establishment Charge and Profit. The contract percentage adjustment shall also apply. For computation of ‘STAR’ rate using Daywork’s Schedule of Rates, the contract percentage adjustment shall NOT apply to the ‘STAR’ rates computation. Part (M) – Play Equipments and Siteworks Rates for each item shall include cost of removal and implementation of precautionary measures where necessary unless otherwise stated. Part (N) – Ceiling Leaks Repairs 1.

All rates in the Schedule shall include: (a) The provision of all necessary tools equipment, labour, plant, machinery and materials and mobilization from unit to unit and from block to block; the emergency repairs to be executed immediately beyond the normal working hours and may also beyond constraint boundary. (b) Addition/replacement of steel reinforcement in concrete components as directed by Superintending Officer. (c) Removal of finishes/fixtures and other obstruction in the course of repair. (d) Removal, cut off supply, diversion and reinstatement of water/electrical supply. (e) The removal of debris from the site in the process of repair or as directed by the Superintending Officer. (f)

The cleaning up of site on completion.

(g) Provision of barricadings, warning signs and warning lights. (h) Provision of props and formworks as directed by the Superintending Officer (for spalling concrete works only). 2.

The provision “per unit” refers to per unit of flat or shop or office, etc. If the work includes two toilets or bathrooms in the same unit and the total area of work done does not exceed 3.5m2, then the Contractor shall only be paid “per job”.

SOR Premable Page 8 PARTICULAR PREAMBLES TO VARIOUS SECTIONS (CONT’D) Part (N) – Ceiling Leaks Repairs (Cont’d) 3.

The terms “per point” means each pipe surround that water leakage repair is carried out. If in a bathroom, the leaking concrete surround the soil pipe, waste pipe and floor trap require repair, the Contractor shall be paid three points.

Part (P) – Piling Works Piling works shall be executed in accordance with the relevant specifications and the instruction of the Superintending Officer. The rates shall include the following: (a)

The removal of underground obstruction together with all work connection.

(b)

The transportation, handling, pitching, heading, pointing, bracing and providing iron or helmet to pile.

(c)

The extending pile, dolly and connection.

(d)

The cutting of surplus and heads of piles, extra excavation, backfilling and disposal of debris.

(e)

The re-driving or intermittent driving necessitated by upheaving or lengthening of piles or by removal of obstruction under piles or other causes including moving and repositioning the piling frame.

(f)

The disposal of materials displaced arising out of driving the piles.

(g)

The assembling of equipment on the site and the subsequent dismantling and removal shall be given separately as an item.

(h)

The movement of piling frames into position and about the site, any necessary excavation or filling required placing the frames, raising or lowering the frames and any staging, barges or the like required to support the frames.

protective wrought

Payment for treated timber piles driven shall be the product of the relevant rate per metre run and the penetration depth (measured from tip to cut-off level). Payment for each reinforced concrete piles after it is driven into the ground is measured from the cutoff level of the pile to the end of pile shoe.

SOR Premable Page 9 PARTICULAR PREAMBLES TO VARIOUS SECTIONS (CONT’D) Premables to Repairs to external Finishes Repairs to external finishes shall be executed in accordance with the relevant kinds described in the Contract and shall confirm to the relevant Statutory Requirements and to be approved by the Superintending Officer. Where trade names or manufacturer’s catalogue numbers are used, the reference is intended only as a guide to the type of article or material. The Contractor may use any other article or material, subject to approval of the Superintending Officer. The following SORs shall be applicable for Repairs to External Finishes. S/N

Section in SORs

SORs

1

C-Brick / Block Works

C002-C004, C012-C033, C037-C039, C043-C044, C051, C056, C058-C07l, C073-C079

2

D-Pavior

D095-Dl00

3

H- Plaster And Wall Tiles

H005, H031-H035, H038-H039, H043H049, H054

4

3-Painter

3035-3037, 3040

5

L- Daywork

L035-L038, L046-L076

During the continuance of repair works, the Contractor shall keep proper records of the quantities (with drawings, sketches, photographs, etc) and descriptions of all materials and plants employed. Such records must be verified by the Superintending Officer before the Contractor is allowed to proceed with the painting and touch up works.

TERM CONTRACT FOR BUILDING TRADESMEN WORKS

S/N

DESCRIPTION

SOR PAGE

1

EXCAVATOR

A1 – A2

2

CONCRETOR

B1 – B12

3

BRICK / BLOCK WORKS

C1 – C9

4

PAVIOR

D1 – D13

5

ROOFER

E1 – E7

6

CARPENTER, JOINER AND IRONMONGER

F1 – F21

7

STEEL AND IRONWORKER

G1 – G35

8

PLASTER AND WALL TIER

H1 – H6

9

GLAZIER

I1 – I2

10

PAINTER

J1 – J7

11

ROADS AND CARPARKS

K1 – K4

12

DAYWORK

L1 – L8

13

PLAY EQUIPMENT & SITE WORKS

M1 – M8

14

CEILING LEAK REPAIRS

N1 – N3

15

PILLING WORKS

P1 – P2

A

-

EXCAVATOR

S/N

DESCRIPTION

SOR PAGE

1

EXCAVATION

A1

2

FILLING

A1

SOR Page A1 Item

Description

Unit

Rate

EXCAVATOR ( To be read in conjunction with Preambles ) Excavation * EXCAVATE TO SITE, TRENCHES, COLUMN BASE ETC commencing from ground level in ordinary ground, including backfilling, forming of surfaces and edges, etc, if necessary within site, for the following average depth. (Removal of surplus excavated material to contractor’s own dumping grounds measured separately under SOR Item A003.) *(A001 A002) Not exceeding 300mm deep A001

Exceeding 300mm and not exceeding 2.Om deep.

m2

5.40

A002

CART AWAY SURPLUS EXCAVATED MATERIAL off site and deposit at the approved dumping ground.

m3

12.80

A003

Excavate to pits, small holes etc not exceeding 0.10m3 to receive base of posts, etc including removing surplus excavated material off site and making good.

m3

4.70

Filling A004

Supply dry approved earth filling obtained from outside source and fill in layers of 300mm including labour for spreading, trimming and consolidating to form earth moulds or levels.

No

6.00

A005

Supply coarse aggregate (19mm to 38mm gauge), spread and level on site as directed.

m3

10.50

A006

Supply sand, spread, level and consolidate.

m3

37.20

A007

* SUPPLY HARDCORE IN BEDS, comprising of clean broken bricks/concrete ,deposit ,spread ,leveled ,mechanically consolidated and including 25mm thick sand blinding/ topping for the following average thickness from surface level : * (A008 A010)

m3

65.20

A008

Not exceeding 150mm thick.

m2

3.10

A009

Exceeding 150mm and not exceeding 300mm thick

m2

5.40

A010

Exceeding 300mm thick

m3

13.80

A011

Supply quarry waste/granite fines, spread, leveled, well rammed

m3

22.70

($)

B

-

CONCRETOR

S/N

DESCRIPTION

SOR PAGE

1

Concrete Work

B1

2

Reinforcement

B2

3

Formwork

B3

4

Drain / Water Channel

B3 – B5

5

Miscellaneous

B6

SOR Page B1 Item

B00l

Description CONCRETOR (To be read in conjunction with Preambles) Concrete Work Supply and cast Grade 10 lean concrete in beds under foundations, column bases, ground beams etc with 20mm to 10mm graded granite mechanically mixed irrespective of thickness.

Unit

Rate ($)

m3

165.00

B002

Supply and cast Grade 15 mass concrete in foundation etc with 20mm to 10mm graded granite mechanically mixed including formwork and working around rod or fabric reinforcement (reinforcement measured separately)* Supply and cast reinforced concrete in foundations, ground beams, etc with 20mm to 10mm granite mechanically mixed, including formwork and working around rod or fabric reinforcement below ground level (Reinforcement measured separately) . *(B003 B007)

m3

169.30

B003

Grade 20

m3

196.00

B004

Grade 25

m3

201.20

B005

Grade 30

m3

205.70

B006

Grade 35

m3

210.40

B007

Grade 40

m3

215.50

* Supply and cast reinforced concrete in suspended slabs, beams, columns, staircases, footpath, apron etc with 20mm to 3mm graded granite mechanically mixed and placed around reinforcement above ground level including PVC strip expansion joint where necessary. (Reinforcement and formwork measured separately) . *(3008 BO12) B008

Grade 20

m3

168.20

B009

Grade 25

m3

172.30

B010

Grade 30

m3

176.80

B011

Grade 35

m3

181.40

B012

Grade 40

m3

186.10

B013

Supply and cast concrete in SMALL quantities not exceeding 0.15 metre cube to match existing, including all necessary formwork.

m3

328.00

B014

Extra over Items B008 to B012 for trowelling concrete to footpath, apron etc.

m2

0.70

B015

Extra over for waterproofing additive in concrete to manufacturer’s instructions.

m3

25.00

SOR Page B2 Item

Description

Unit

Rate ($)

B016

Reinforcement Supply mild steel rod reinforcement fabricated and laid in position including labour for forming stirrups, links, etc irrespective of size

kg

1.60

kg

1.60

B018

* Supply and place BRC or other equal and approved welded steel FABRIC REINFORCEMENT well lapped (minimum 1 square) and tied at joints (measured nett) *(B0l8 B037) A5

m2

3.70

B019

A6

m2

4.80

B020

A7

m2

5.60

B021

A8

m2

7.00

B022

A9

m2

10.60

B023

Al0

m2

15.00

B024

B6

m2

7.30

B025

B7

m2

8.60

B026

B8

m2

10.20

B027

B10

m2

12.90

B028

C6

m2

8.00

B029

C7

m2

10.20

B030

C8

m2

12.40

B031

D6

m2

8.00

B032

D7

m2

10.20

B033

D8

m2

12.40

B034

D10

m2

18.60

B035

No. 2210 ( 3.25 mm 50 x 50 mm )

m2

6.40

B036

No. 5515 ( 1.83mm 12.5 x 12.5mm )

m2

9.00

B037

No. 3315 ( 1.83mm 75 x 75mm )

m2

3.50

B017

Supply high tensile steel rod reinforcement irrespective of size fabricated and laid in position including labour for forming stirrups, links, etc irrespective of size

SOR Page B3 Item

Description Formwork

Unit

Rate

B038

Supply and erect timber formwork to surfaces of concrete, columns, walls, suspended slabs, stairs, canopies, beams, lintels, etc. (Measured net of concrete surface)

m2

17.80

B039

Extra over timber formwork for curve surface work.

m2

3.50

Drain/Water Channel * Construct 230mm wide (internal)CONCRETE (Grade 25) SURFACE DRAIN with 100mm thick sides, 100mm thick base reinforced with a layer of BRC No. B6 wiremesh. All exposed sides, base and arises rendered smooth in cement mortar (1:3) including all necessary excavation, hardcore, sand blinding and formwork, laid to fall as directed for the following average depth to invert: *(B040 B042) B040

Not exceeding 300mm deep

m

44.30

B041

Exceeding 300mm but not exceeding 450mm deep

m

57.60

B042

Exceeding 450mm but not exceeding 600mm deep

m

70.90

B043

Construct 230mm wide (internal) reinforced concrete (Grade 25) surface drain with 100mm thick sides and base reinforced with a layer of BRC No, 36 wire mesh. All exposed sides, base and arises rendered smooth in cement mortar (1:3) including all necessary excavation, hardcore, sand blinding and formwork, laid to fall as directed for more than 600mm depth to invert

m

84.20

B044

Extra over items for precast concrete channel to 230mm wide reinforced concrete surface drain.

m

3.50

* Construct 305mm wide (internal)CONCRETE (Grade 25) SURFACE DRAIN with 100mm thick sides and base reinforced with a layer of BRC No. B6 wire mesh. All exposed sides, base and arises rendered smooth in cement mortar (1:3) including all necessary excavation, hardcore, sand blinding and formwork, laid to fall as directed for the following average depth to invert : *(B045 B048) B045

Not exceeding 300mm deep

m

48.70

B046

Exceeding 300mm but not exceeding 450mm deep.

m

62.20

B047

Exceeding 450mm but not exceeding 600mm deep.

m

75.70

B048

Exceeding 600mm deep

m

89.20

B049

Extra Over for Precast Concrete channel to 305mm wide reinforced concrete surface drain.

m

8.00

B050

Extra over Items B040 to B042 and 3045 to B048 for forming 50mm x 25mm rebate on both sides of channel for precast drain cover slab (Measurement based on length of drain)

m

3.30

Break up concrete/surface drain including cutting reinforcement and removing debris off site.

m3

77.10

B051

($)

SOR Page B4 Item

Description

Unit

Rate ($)

* REPAIRS to 150mm to 305mm wide concrete drain of the following depth to invert; hack off existing rendering at sides and invert of drain, remove damaged or cracked portions of drain, patch up with concrete, form key and re-render drains (whole girth) to proper falls in cement mortar (1:3) *(B052 B053) B052

Not exceeding 300mm deep

m

13.60

B053

Exceeding 300mm deep but not exceeding 450mm deep

m

23.50

* Hack out existing concrete drain invert (Average Depth not exceeding 600mm) and regrade to fall towards outlet with cement and sand (1:3) screed and finished smooth. *(B054 B055) B054

230mm wide

m

8.80

B055

305mm wide

m

9.60

* Hack out existing carpark drain invert and regrade drain 450 to 600mm width to fall towards outlet with cement and sand (1:3) screed and finished smooth. *(3Q55 B057) B056

Average depth not exceeding 800mm

m

10.50

B057

Average depth exceeding 800mm

m

14.00

* Break up damaged half round precast concrete channels and reconstruct same in cement mortar (1:3) including laying to proper falls and making good sides of channel *(B058 B0E0) B058

150mm diameter

m

18.00

B059

230mm diameter

m

20.20

B060

305mm diameter

m

25.56

B061

Break up damaged/sunken 300mm closed conduit drain spun pipe include hacking through floor, excavation, planking, making good etc. and reconstruct same jointed in cement mortar (1:3) to proper falls including lean concrete base

m

79.50

* Supply and lay precast concrete composite channel laid to even falls and jointed in cement and sand (1:3) mortar as detail drawing (EM-TCSTD-BLDG-99-12) *(B062 B067) B062

810mm x 495mm - Type C7

m

44.50

B063

595mm x 355mm - Type C7A

m

34.00

B064

395mm x 195mm Type C73

m

29.20

B065

1200mm x 750mm - Type C8

m

70.90

B066

900mm x 535mm - Type C8A

m

55.70

B067

995mm x 610mm - Type C83

m

62.50

SOR Page B5 Item

Description

Unit

Rate ($)

m

23.90

m

19.00

m

21.80

Reconstruct existing scupper drain outside bin chute chamber with new half round salt glazed stoneware pipes, side and base embedded in G20 concrete including adjusting existing gulley to match drain level bedded and jointed with cement mortar (1:3). B068

* Supply and lay half round salt glazed stoneware pipe in replacement jointed with cement and sand mortar (1:3) as scupper drain including lean concrete base. *(3069 B070)

B069

100mm diameter

B070

150mm diameter

B07l

Construct scupper drain not exceeding 150mm wide and 75mm deep on existing floor including trowelling surface smooth

m

6.20

B072

Regrade existing scupper drain with waterproofing cement and sand (1:3) screed laid to fall not exceeding 150mm wide and 75mm deep including trowelling surface smooth

m

5.00

B073

Regrade existing scupper drain with waterproofing cement and sand (1:3) screed laid to fall exceeding 150mm but not exceeding 300mm wide, 75mm deep including trowelling surface smooth

m

6.30

B074

315mm diameter UPVC pipe conforming to SS272 for concealed drain outlet with Grade 30 concrete bed and reinforced with BE BRC including formwork and lean concrete (excavation measured separately)

m

58.50

B075 to B093 NOT IN USE

SOR Page B6 Item

Description Miscellaneous

Unit

Rate

($)

B094

Break up concrete

m3

77.10

B095

Break up concrete, part re-use as hardcore, well rammed, leveled and consolidated and surplus cart away off site, including cutting reinforcement, if any.

m3

84.40

B096

Cutting through reinforced concrete floors or walls (any thickness) to form openings.

m3

390.40

Form bituminous expansion joint in concrete floors including all necessary formwork and bituminous seals (B097 3098) B097

13mm x 75mm deep

m

4.50

B098

25mm x 100mm deep

m

11.70

B099

Form expansion joint with foam plastic infill

m2

3.20

Bl00

Rake out existing damaged/worn out Bituminous Expansion Joint in concrete floors and refill same with approved hot bitumen.

m

3.80

B101

Supply and plug up bin chute wall holes with 300mm diameter detachable precast concrete complete with 13mm diameter mild steel handle (exclude breaking existing concrete wall)

No

17.90

B102

Provide diamond saw—cutting to concrete floor to form 3mm width x 40mm depth (mm) contraction joint.

m

2.00

Bl03

Provide diamond saw-cutting or other approved equipment to cut homogeneous / ceramic tiles, slate tiles, quarry tiles and other floor finishes to form groove lines including make good all affected areas

m

2.50

Bl04

Provide diamond saw-cutting to apron slab/drain wall to form 50mm rebate for placing of precast concrete drain cover slab. (Measurement based on rebate length)

m

4.00

B105

Provide 100mm wide Diamond Saw-Cutting” profile around concrete electrode / lightning protection inspection pit inclusive of the removal of all loosened concrete, casting of new Grade 25 concrete and the trowel smooth all affected areas

No.

15.50

B106

To provide 150mm long PVC weep hole pipes not exceeding 50mm dia through brick / concrete work not exceeding 100mm thick

No

3.60

B107

Raise or lower existing manhole cover and frame to match the existing level of path or paving

No

17.80

B108 to B146 NOT IN USE

C

-

S/N

BRICK / BLOCK WORKS

DESCRIPTION

SOR PAGE

1

Brick / Hollow Block

C1 – C3

2

Glass Block Works

C3

3

Water Seepage Treatment

C3 – C4

4

Miscellaneous

C4 – C6

SOR Page C1 Item

Description BRICK/BLOCK WORKS

Unit

Rate ($)

(To be read in conjunction with Preambles) Brick/Hollow Block * Common Brickwall (size 215 x 102.5 x 65mm) laid in compo mortar with 10mm joints raked 10mm deep or flush pointed as work proceeds. *(C00l C004) C001

Generally

m3

259.60

C002

One brick thick

m2

59.00

C003

Half brick thick reinforced with expanded metal brickwork reinforcement at every 4th course.

m2

29.80

C004

Half brick thick built in honeycomb

m2

23.80

C005

75mm thick BRICK-ON-EDGE reinforced with expanded metal brickwork reinforcement at every course with 10mm joints raked 10mm deep or flush pointed as work proceeds

m2

19.00

C006

Extra over common brickwork for forming fairfaced brickwall including pointing in approved tinted cement mortar. (Applicable to C002 to CQO4)

m2

5.00

m2

80.00

m2

49.00

C007

C008

One brick wall with facing bricks both sides, laid in compo mortar (1:3) with 10mm joints raked 10mm deep or flush pointed in approved tinted cement mortar as work-proceeds Half brick wall with facing bricks with expanded metal brickwork reinforcement at every 4th course laid in compo mortar (1:3) with 10mm joints raked 10mm deep flush pointed in approved tinted cement mortar as work proceeds * Hollow block as specified in compo cement mortar (1:3) flush pointed as work proceeds (reinforced with expanded metal brickwork reinforcement at alternate course) *(C009 C010)

C009

100mm thick

m2

17.90

C010

150mm thick

m2

27.80

C011

100mm thick hollow block in compo mortar (1:3) and reinforced expanded metal reinforcement in alternate course and blocks in each course filled in solid with Grade 20 concrete

m2

24.20

m2

49.50

m2

25.30

* Common Modular Brickwall laid in prepacked mortar with 10mm joints raked 10mm deep or flush pointed as work proceed. *(C012 0014) C012

190mm thick using M211 modular brick size 190 x 90 mm x 90mm.

C013

90mm thick using M211 modular bricks size 190 x 90mm x 90mm reinforced with expanded metal brickwork reinforcement at every four course.

21

SOR Page C2 Item

Description

Unit

Rate ($)

C014

90mm thick using M311 modular bricks size 290 x 90mm x 90mm reinforced with expanded metal brickwork reinforcement at every fourth course.

m2

16.40

C015

Supply labour and materials to rake out mortar joints between standard bricks and repointing with polymer modified cement mortar (based on area of brickwall)

m2

10.90

C016

Supply labour and matrials to rake out mortar joints between modular bricks and repointing with polymer modified cement mortar (based on area of brickwall)

m2

9.50

EXTRA OVER standard common bricks (size 215 x 102.5 x 65mm) for the following bricks C017

Red hacking bricks

m2

19.20

C018

Overburnt facing bricks

m2

30.00

C019

Brown facing bricks

m2

34.00

C020

Pebble facing bricks

m2

34.00

C021

Apricot facing bricks

m2

38.00

C022

Desert facing bricks

m2

34.00

C023

Grey facing bricks

m2

38.00

EXTRA OVER common modular bricks for using the following facing bricks to one face of the brickwall (applicable to brickwall of thickness 190mm and above) *(C024 C030) C024

Red facing brick

m2

47.80

C025

Overburnt facing bricks

m2

55.70

C026

Brown facing bricks

m2

59.70

C027

Pebble facing bricks

m2

67.70

C028

Apricot facing bricks

m2

82.70

C029

Desert facing bricks

m2

67.70

C030

Grey facing bricks

m2

77.60

SOR Page C3 Item

Description Extra over brick wall for the provision of HOT-DIPPED GLAVANISED STEEL WALL TIE SYSTEM fastened vertically to reinforced concrete surfaces including HOT-DIPPED GALVANISED BONDING BAR SYSTEM at both end edges of brick wall as shown in drawing no. EM-T0-STD-BLDG-04D2-08 *(C031 C032)

Unit

Rate

C031

Brick wall cladding to rc wall

m2

12.00

C032

Outer leaf of brick cavity wall cladding to rc wall

m2

12.20

C033

Extra over half brickwall/solid block wall for the provision of HOT DIPPED GALVANISED BONDING BAR SYSTEM to the end edges of brick wall/solid block wall as shown in drawing no. EM-T0-STD-BLDG- 0402-0 B

m

5.40

Glass Block Work C034

180mm to 195mm square glass block of 80mm to 100mm thick laid in compo cement mortar (1:3) and pointed with approved tinted cement mortar complete with panel reinforcing, panel anchors, expansion strips, etc. according to manufacturer’s instructions

m2

270.60

C035

“NEG” or other approved Glass block wall consists of 145 x 145 square glass block of 80 to 100mm thick glass laid in compo cement mortar (1:3) and pointed with approved tinted cement mortar complete with panel reinforcing, panel anchors, expansion strips, etc. according to manufacturer’ s instructions

m2

284.30

C036

Supply labour and material to rake out broken/damaged glass blocks of any size and replace with new glass block to match existing (for remedial work not exceeding 10 nos. glass blocks)

No

13.60

Water Seepage Treament TREATMENT TO WATER SEEPAGE (SCAFFOLDING/GONDOLAS MEASURED SEPARATELY FOR WORKS ABOVE 6 METRE HEIGHT) C037

Rake out joints to an even depth of 25mm to 30mm. Brush out all loose materials and fill the groove solid with approved polyurethane sealant/ polysuiphide sealant in accordance with manufacturer’s instruction to form a continuous sealant (Gondola measured separately)

m

8.20

C038

Extra over item for filling the groove/ expansion joint solid with an approved backing rod.

m

1.40

C039

Supply labour and materials to form splay with approved polymer modified cement mortor/non shrink grout to the correct gradient including hacking when necessary

m

5.00

C040

Repair the brick/tiled wall panels by washing, patching cracks and applying 1 coat of approved adhesion promoter and 2 coats of approved elastorneric waterproofing coating according to manufacturer’s instructions

m2

10.40

($)

SOR Page C4 Item

Description

Unit

Rate

C041

Repair hollow-block or solid-block wall panels by washing, patching cracks and applying 1 coat of approved adhesion promoter and 2 coats of approved elastomeric waterproofing coating according to manufacturer’ s instruction

m2

9.60

C042

Repair the reinforced concrete/plastering finished wall panels by washing, patching cracks and applying 1 coat of approved adhesion promotor and 2 coats of approved elastomeric waterproofing coating according to manufacturer’s instructions

m2

9.00

C043

Apply 2 coats of clear elastometric waterproof membrane as specified including patching hairline cracks on brick wall with brick colour cement if necessary

m2

6.30

C044

Apply 2 coats of clear elastometric waterproof membrane as specified including patching hairline cracks on brick wall if necessary

m2

5.40

C045

Repair the patch joints between precast sills by mortar joint and approved polyurethane sealant according to manufacturer’ s instructions

No.

1.60

Apply approved polyurethane sealant to joints, pointing, grooved, cracks etc between frames, block walls, brick walls, rc walls, etc, according to manufacturer’s instructions.

m

3.90

Apply approved silicon sealant to joints, pointings, grooves, etc. according to manufacturer’ s instructions

m

1.70

Repair to reinforced concrete beam cracks by hacking out existing crack and patch it with 1:3 cement and sand mortar gauged with approved synthetic latex or other approved additive including painting 2 coats of emulsion paint to the repaired surface.

m

6.40

C046

C047 C048

Miscellaneous C049

Labour and material for pointing joints of brickworks in coloured cement.

m2

4.20

C050

Labour for raking out joints of existing brickwork, clean, re-jointing with cement mortar and re-pointing with a flush joint.

m2

5.90

C051

Breaking up existing block or brick work in cement mortar including plaster (measured gross thickness)

m3

24.00

C052

Cutting out existing block or brick work to form chase etc not exceeding 300mm girth

m

7.30

C053

Cutting out block or brickwork to form chase exceeding 300mm but not exceeding 600mm girth

m

9.90

C054

Cutting out block or brickwork to form opening

m3

101.70

C055

Lay approved damp proof course well lapped at joints and bedded in cement mortar (1:3) according to manufacturer’s instructions

m2

8.90

($)

SOR Page C5 Item

Description

Unit

Rate

($)

C056

Supply and lay approved horizontal damp proof course complied with BS 6398 Type B (felt fibre base) to brick/block walls bedded in prepacked mortar as specified

m2

8.90

C057

Hack out cracks of brick or block walls to form ‘V’ shaped grooves approximately 25mm wide x 20mm deep and seal up with polymer modified mortar and painting surfaces to match existing.

m

4.00

C058

Apply 2 coats of approved silane/siloxane based water penetrant as specified including patching hairline cracks on brick wall with brick colour cement if necessary.

m2

6.60

C059

Repair to cracks by hacking RUT’ groove on the cracks to 25mm width x 20mm depth. Brush out all loose sand and mortar and fill the groove with polymer modified mortar including painting to the repaired surface.

m

6.50

C060

Repair to cracks by hacking V grooves on the cracks and patch with approved polysulphide sealant including painting to the repaired surface

m

19.40

C06l

Supply labour and materials to repair the defective plaster by touching up defective concrete substrate with polymer modified mortar and skimming to average 6mm thick approved materials including hacking, applying bonding agent and painting and all as specified

m2

26.40

C062

Supply labour and materials to repair the plastered wall panels by applying two coats of approved prepacked skim coat including hacking, painting to the repaired surface

m2

13.50

C063

Supply labour and materials to repair defective plaster with average 18mm thick prepacked mortar including hacking, apply bonding agent and painting and all as specified

m2

20.70

C064

Supply labour and materials to repair the defective plaster with average 18mm thick polymer modified mortar including hacking, apply bonding agent and painting and all as specified

m2

44.10

C065

Installation of special wall tie to existing brickwall including galvanised mesh sleeve, approved resin, stainless steel wall tie

no

8.10

C066

Form nib with non shrink grout including Chemical Capsule @ 300mm centre to centre, necessary reinforcement, formwork, skimming coat and painting

m3

3,835.10

SOR Page C6 Item C067

Description Form nib with Grade 30 concrete including Chemical Capsule @ 300mm centre to centre, necessary reinforcement, formwork, skimming coat and painting

Unit m3

Rate ($) 2812.60

C068

Watertightness test to external wall by spraying water at 300 litre/hour (Gondola measured separately)

hr

9.70

C069

Watertightness test to external wall by spraying water at 600 litres/hour as specified (gondola measured separately and water provided by PA without charges)

hr

10.50

C070

Watertightness test to exteria1 wall by spraying water at 300 litre/hour using perforated PVC pipe

hr

7.50

C07l

Watertightness test to external wall by spraying water at 600 litre/hour using perforated PVC pipe

hr

8.20

C072

Hammer dressed random rubber in granite laid in prepacked mortar and pointed in coloured cement

m3

222.70

C073

13mm deep polyurethane sealant joint (horizontal or vertical) with 10mm diameter backer rod to fill gap between brickwall and beam/column as specified

m

4.20

C074

Supply and fix 100mm x 80mm x 6mm thick galvanised angle plate with approved 8mm diameter chemical adhesive galvanised stud archor @ 150 c/c to existing wall

m

50.80

C075

Supply labour and materials to rack out mortar joint at the interface to a depth of 25mm. Brush out all loose sand and mortar and fill the groove with polymer modified mortar

m

4.20

C076

Supply labour and materials to repair insitu-laid external tiles with G25 concrete screed and colour elastomeric membrane including hacking and all as specified

m2

23.40

C077

Supply labour and materials to repair insitu-laid external tiles with approved prepacked skimming materials and colour elastomeric membrane including hacking and all as specified

m2

21.60

C078

Supply labour and materials to rake out existing mortar joint, brush out all loose materials, fill the joint with approved backing rod, follow up with approved non- shrink grout in accordance with the manufacturer’ s instructions

m

7.60

C079

Strengthening of existing brickwalls, tile cladding, etc with ‘Hilti’ HRD wall tie including drilling holes, brush out all loose materials, fill hole with nonshrink grout and touch up hole with paint to match existing

No

7.70

D – PAVIOR Contents S/N Cement and Sand Rendering 1

SOR Page D1

2

Granolithic Paving

D2

3

Coloured Cement Paving

D2

4

Cast-in-Situ Terrazzo

D3

5

Mosaic Tiling

D2 – D3

6

Brick Paving

D3

7

Ceramic Floor Tiling

D3 – D4

8

Slate Tiling

D5

9

Quarry Tiling

D5

10

Teak Parquet Floor Tiling

D5

11

Interlocking Block Paving

D6

12

Imprint Coating System

D7

13

Pebble Wash Finishing

D7

14

Concrete Topping

D8

15

Vinyl Tiling

D8

16

Self Levelling Screeding

D8

17

Dividing Strips

D8

18

Epoxy Mortar Screeding

D8

19

Coloured Grout Finishing

D8

20

Natural Stone Finishing

D8

21

Miscellaneous

D8 – 9

22

Epoxy Sediment Coating System

D9

23

Repair to Concrete Surface

D9

SOR Page D1 Item

Description

Unit

Rate ($)

PAVIOR (To be read in conjunction with Preamble) Cement and Sand Rendering * Cement and sand (1:3) rendering to ground floor trowelled to a smooth finish *(D001 D002) D001

20mm thick

m2

6.90

D001

For every 5mm thick exceeding 20mm thick up to a maximum of 60mm thick.

m2

1.40

* 20mm thick cement and sand (1:3) to form skirtings, treads, risers, curbs and return etc including coved and rounded angles for *(D003 DOOS) D003

Not exceeding 150mm girth

m

4.40

D004

Exceeding 150mm but not exceeding 300mm girth

m

6.90

D005

Exceeding 300mm but not exceeding 450mm girth

m

8.50

* 20mm thick cement and sand (1:3) to upper floor trowelled to a smooth finish *(D006 D007) D006

20mm thick m2 6.70

m2

8.30

D007

For every 5mm thick exceeding 20mm thick up to a maximum of 60mm thick.

m2

1.75

m

4.60

m

7.20

m

8.90

m2

0.50

* 20mm thick cement and sand (1:3) skirtings, treads, risers, curbs and return etc including coved and rounded angles for *(D008 D010) D008

Not exceeding 150mm girth

D009

Exceeding 150mm but not exceeding 300mm girth

D010

Exceeding 300mm but not exceeding 450mm girth

D011

Extra over for approved waterproofing compound incorporated in the cement paving for each 5mm thickness (applicable to other pavior items).

D012

Extra over for using hardener or other approved non-metallic hardener mixed according to manufacturer’s instruction for each 5mm thickness (applicable to other pavior items)

m2

1.50

D013

Extra over 3mm thick coloured cement topping finish of terracotta, white, red and green colour, surface floated smooth with a steel trowel

m2

9.60

SOR Page D2 Item

Description Granolithic Paving

Unit

Rate ($)

* Granolithic consisting of cement, sand and granite chipping (1:1:2) to floor trowelled to a smooth finish including PVC strip expansion joint where applicable *(D014 D0l5) D014

20mm thick

m2

10.00

D015

For every 5mm thick exceeding 20mm thick up to a maximum of 60mm thick

m2

1.20

* 20mm thick Granolithic skirting, treads, risers, curbs and returns etc including coved and rounded angles for *(D0l6 D017) D016

Not exceeding 150mm girth

m

4.90

D017

Exceeding 150mm but not exceeding 300mm girth

m

6.70

D018

25mm thick Granolithic exposed aggregate paving consisting of cement, sand and - granite chipping of (2:1:5) laid in panels with 12mm x12mm deep recessed joints laterally at 1.2m centres

m2

24.60

m2

21.30

m2

26.70

m2

43.70

Coloured Cement Paving D019

20mm thick single coloured cement paving to floor laid in panels on and including minimum 10mm thick cement and sand (1:3) base screed.

D020

20mm thick multi-coloured cement paving to floor laid in panels including minimum 10mm thick cement and sand (1:3) base screed Cast-in-situ terrazzo

D021

20mm thick terrazzo finish to floor laid in sections, on and including minimum 20mm thick cement and sand (1:3) base screed, polishing to approval * 20mm thick terrazzo skirtings, treads, risers, curbs and returns etc including coved and rounded angles polishing to approval *(D022 D023)

D022

Not exceeding 150mm girth

m

9.00

D023

Exceeding 150mm but not exceeding 300mm girth

m

15.00

Mosaic Tiling * Semi-glazed mosaic tiles of approved colour and pattern to floor laid and jointed in cement grout on and including minimum 13mm thick cement and sand (1:3) base screed and pointed in cement * (D024 D026) D024

To floor

m2

50.40

D025

Not exceeding 150mm girth to skirtings, treads, risers, curbs and returns etc with all necessary coved and rounded angles

m

10.20

D026

Exceeding 150 but not exceeding 300mm girth to skirtings, treads, risers, curbs and returns etc with all necessary coved and rounded angles

m

18.20

SOR Page D3 Item

Description * Unglazed mosaic tiles of approved colour and pattern laid and jointed in cement grout on and including minimum 13mm cement and sand (1:3) screed and pointed in cement. *(D027 D029)

Unit

Rate ($)

D027

To floor

m2

49.10

D028

Not exceeding 150mm girth to skirtings, treads, risers, curbs and returns etc. with all necessary coved and rounded angles

m

9.40

D029

Exceeding 150 but not exceeding 300mm girth to skirtings, treads, risers, curbs and returns etc with all necessary coved and rounded angles

m

16.50

Brick Paving D030

Hack off existing damaged brick-on-edge on steps, coping, footpath

m2

5.20

D031

Supply and lay new brick on edge in cement mortar (1:3) to existing steps, coping, footpath, etc, including proper surface preparation pointing with cement mortar

m2

58.30

D032

Brick-on-edge paving in facing brick laid to approved pattern and bedded on and including minimum 13mm thick cement and sand (1:3) screed and pointed in cement mortar.

m2

50.10

D033

Brick-on-edge paving in single bull-nose one brick width laid and bedded on and including minimum 13mm thick cement and sand (1:3) screed and pointed in cement mortar.

m

17.60

D034

Brick on edge paving in double bull-nose one brick width laid and bedded on and including 13mm cement and sand (1:3) screed and pointed in cement mortar.

m

22.00

D035

Supply and lay brick-on-edge at (minimum 60° inclination from ground level) single bull-nose brickwork in compo mortar with bedding and 10mm joints including excavation and leveling from site and leveling

m

19.40

D036

Brick tiles laid to approved pattern jointed, pointed and bedded on and including 13mm thick cement and sand (1:3) screed.

m2

44.60

m2

58.60

Homogeneous/Ceramic Floor Tiling D037

Supply and lay any size, minimum 8mm thick heavy duty homogeneous polished floor tile of approved colour and pattern, jointed, pointed and bedded on and including minimum 20mm thick cement and sand screed (1:3) * Supply and lay to skirtings, treads, risers, curbs, nosings and returns, any size, minimum 8mm thick heavy duty homogeneous polished tile of approved colour and pattern, jointed, pointed and bedded on and including minimum 20mm cement and sand screed (1:3) *(D038 D040)

D038

Not exceeding 150mm girth

m

11.30

D039

Exceeding 150mm but not exceeding 300mm girth

m

21.80

D040

Exceeding 300mm but not exceeding 450mm girth

m

33.20

SOR Page 4 Item

Description * Supply and lay any size, minimum 8mm thk heavy duty homogeneous polished floor tile of approved colour and pattern, jointed & pointed with approved grout *(D041 D044)

Unit

Rate ($)

D041

Not exceeding 0.1m2 (for single patch)

No.

6.90

D042

Exceeding 0.lm2 but not exceeding 0.3m2(for single patch)

No.

19.00

D043

Exceeding 0.3m2 but not exceeding 0.5m2 (for single patch)

No.

29.50

D044

Exceeding 0.5m2 but not exceeding lm2 (for single patch)

No.

59.00

D045

Supply and lay any size, minimum 8mm thick, heavy duty homogeneous unpolished floor tile of approved colour and pattern, jointed, pointed and bedded on and including minimum 20mm thick cement and sand screed (1:3)

m2

39.00

* Supply and lay to skirtings, treads, risers, curbs, nosings and returns, any size, minimum 8mm thick, heavy duty homogeneous unpolished tile of approved colour pattern, jointed, pointed and bedded on including minimum 20mm cement and sand screed (1:3) *(D046 D048) D046

Not exceeding 150mm girth

m

8.30

D047

Exceeding 150mm but not exceeding 300mm girth

m

14.20

D048

Exceeding 300mm but not exceeding 450mm girth

m

20.80

No.

6.50

No.

17.00

No.

27.00

No.

49.00

m2

25.00

m

6.50

m

10.60

m

17.10

m

13.10

* Supply and lay any size, minimum 8mm thk heavy duty homogeneous unpolished floor tiles of approved colour and pattern, jointed and pointed with approved grout (1:3) *(D049 D052) D049

Not exceeding 0.lm2 (for single patch)

D050

Exceeding 0.lm2 but not exceeding 0.3m2(for single patch)

D051

Exceeding 0.3m2 but not exceeding 0.5m2(for single patch)

D052

Exceeding 0.5m2 but not exceeding l.0m2(for single patch) * Supply labour for laying ceramic tiles (any grade, size, colour and pattern) jointed and pointed with approved grout including minimum 20mm thick cement and sand screed *(D053 D056)

D053

To floor

D054

Not exceeding 150mm girth to skirting, treads riser, curbs, nosings and returns

D055

Exceeding 150mm but not exceeding 300mm girth to skirting, treads, riser, curbs, nosings and returns

D056

Exceeding 300mm but not exceeding 450mm girth to skirting, treads, riser, curbs, nosings and returns

D057

Nonslip nosing tile 200x 60 x 8mm in steps or infront lift car entrance laid in approved colour, jointed and pointed and bedded on and including minimum 20mm thick cement and sand screed (1:3)

OR Page 5 Item

Description Slate Tiling * Supply and lay natural slate tiles in any approved colours and pattern jointed and pointed and bedded on and including minimum 20mm thick cement and sand screed (1:3) *(D058 D062)

Unit

Rate ($)

D058

10mm to 15mm thick

m2

37.70

D059

16mm to 20mm thick

m2

44.60

D060

Not exceeding 150mm girth to skirtings, treads, risers, curbs, nosing and returns.

m

6.50

D061

Exceeding 150mm but not exceeding 300mm girth to skirtings, treads, risers, curbs, nosing and returns.

m

11.90

D062

Exceeding 300mm but not exceeding 450mm girth to skirtings, treads, risers, curbs, nosing and returns.

m

19.60

Quarry / Klinker Tiling * Quarry / Klinker tiles of the following size laid and bedded on and including minimum 20mm thick cement and sand screed (1:3) *(0063 0066) D063

100 x 100mm size

m2

35.50

D064

200 x 100mm size

m2

34.20

D065

Any size of 12 - 20mm thick

m2

52.60

D066

Not exceeding 150mm girth to skirting, treads risers, curbs, nosing and returns.

m

4.80

* Supply and lay quarry / klinker tiles of approved colour and pattern, jointed, pointed and bedded on and including minimum 20mm thick cement and sand screed (1:3) *(0067 0070) D067

Not exceeding 0.lm2 (for single patch)

No.

4.60

D068

Exceeding 0.1m2 but not exceeding 0,3m2 (for single patch)

No.

13.10

D069

Exceeding 0.3m2 but not exceeding 0.5m2(for single patch)

No.

18.90

D070

Exceeding 0.5m2 but not exceeding 1.0 m2 (for single patch)

No.

37.90

Teak Parquet Floor Tiling * Supply and lay teak parquet floor tile to match existing inclusive of approved adhesive and sanding down *(D07l 0073) D071

10mm thick.

m2

36.60

D072

13mm thick

m2

42.10

D073

20mm thick

m2

53.70

D074

Scrape off existing damaged parquet floor tile and remove all adhesive stains

m2

5.10

SOR Page 6 Item

Description Interlocking Block Paving

Unit

Rate ($)

* Supply and lay interlocking concrete paving blocks (any colours and patterns) to footpath/concourse to match existing including compacting ground with additional sand bed to required level. *(D075 D076) D075

60mm thick block

m2

32.40

D076

80mm thick block

m2

34.30

* Supply and lay interlocking concrete paving blocks (any colours and patterns) to new footpath including compacting with 40mm thk (mm) sand bed (Excavation and hardcore measured separately) *(0077 D079) D077

60mm thick

m2

26.80

D078

80mm thick

m2

29.00

D079

100mm thick

m2

31.40

D080

Supply and lay 60mm thick interlocking brick paving blocks to footpath/concourse to match existing damaged blocks, compacting and laying additional sand-bed to required level

m2

30.80

D081

Supply and lay 60mm thick interlocking brick paving blocks to new footpath/ concourse including compacting with 40mm thk (mm) sand bed (Excavation & hardcore measured separately)

m2

27.80

D082

Construct 100 x 200mm depth side kerb with grade 25 concrete including all necessary formwork

m

5.20

D083

Labour for taking out loosen sunken, interlocking concrete/brick paving block and relay paving blocks including compacting ground with additional hardcore and to required level and filling of voids

m2

9.20

Composite Rate for Construction of Interlocking Concrete Paving Blocks * Supply and lay interlocking concrete paving blocks (any colour and patterns) to new footpath, concourse area, etc including excavation of site on ordinary ground, backfilling, forming of surfaces and edges making good, removal of surplus excavated material off site to approval dumping ground, 150mm thick hardcore including 25mm thick sand binding, compaction of ground, compacting with minimum 40mm thick sand bed D084

60mm thick (excavation not exceeding 250mm deep)

m2

29.80

D085

80mm thick (excavation not exceeding 270mm deep)

m2

33.10

D086

100mm thick (excavation not exceeding 290mm deep)

m2

36.90

SOR Page 7 Item

Description Imprint Coating System

Unit

Rate ($)

D087

Supply and lay “Superkote” or other approved high strength polymer coating imprint to floor according to manufacturer’ s instruction

m2

23.00

D088

Supply and lay imprint surface in any colour to floor with 20mm thick cement and sand screed according to manufacturer’s instruction

m2

32.00

D089

Supply and lay 20mm thick concrete paving to floor imprint with recessed pattern, approved colour and varnish to match existing floor

m2

30.20

D090

Supply and lay 50mm thick concrete stamping finish in patterns to floor according to manufacturer’s instruction(concrete base measured separately)

m2

34.20

Pebble Wash Finishing D091

Supply and lay 15mm thick pebble wash/ coloured granolithic finish to floor, laid in section

m2

34.50

D092

Supply and lay border 100 to 150mm girth with pebble washed/coloured granolithic finish of 15mm thick

m

7.30

D093

Supply and lay border 150 to 300mm girth with pebble washed/colour granolithic finish of 15mm thick

m

12.30

D094

Extra over for every 5mm thick for Item D091 to D093

m2

8.30

Concrete Topping * Grade 25 concrete screed with 10mm maximum size aggregate trowelled to smooth surface as specified. *(D095 D100) D095

20mm thick

m2

9.20

D096

For every 5mm thick exceeding 20mm thick up to a maximum of 60mm thick

m2

1.55

D097

Not exceeding 150mm in height/width

m

6.70

D098

Exceeding 150mm but not exceeding 300mm in height/width

m

9.60

D099

ADD to (or deduct from) Item 0097 for each 5mm thickness over (or under) 25mm

m

0.90

D100

ADD to (or deduct from) Item 0098 for each 5mm thickness over (or under) 25mm Grade 40 structural concrete with 10mm maximum size aggregate topping including working around rod or fabric reinforcement (reinforcement measured separately) and trowelled to smooth surface with powerfloat as specified. *(D10l D102)

m

1.25

D101

25mm thick

m2

13.20

D102

For every 5mm thick exceeding 25mm thick up to a maximum of 60mm thick

m2

1.80

SOR Page 8 Item

Description Vinyl Tiling

Unit

Rate ($)

D103

Supply and lay 2mm thick vinyl floor tile to match existing inclusive of approved adhesive (Removal measured separately)

m2

18.30

m2

17.50

m

4.70

m

6.90

m

8.10

m

9.70

m

2.40

m2

41.00

m2

16.30

m2

44.90

Self-levelling Screeding D104

Supply and lay self-levelling topping screed minimum 6mm thick (cementitious based) flooring with bonding agent and rubber strip expansion joint to fall with minimum 6mm thickness complete with one layer of sealer coat to manufacturer’s instruction Dividing Strips

D105

Mosaic tiles to form court line(38mm to 50mm wide) for badminton, sepak takraw and basketball courts etc.

D106

25mm x 3mm aluminium dividing strips

D107

25mm x 3mm copper dividing strips

D108

25mm x 3mm stainless steel dividing strips

D109

PVC’L’ shaped strips Epoxy Mortar Screeding

D110

Supply and apply epoxy mortar screed flooring system with epoxy resin primer follow by a layer of minimum 5mm thick epoxy mortar and a non-slip sealer coat after 24 hours curing Coloured Grout Finishing

D111

Supply and lay one coat of finishing grout colour (sundek or other approved) to match existing complete with one coat of acrylic clear top coat for repair to colour screed surface Natural Stone, Finishing

D112

Supply and lay solhofen natural stones of approved pattern, jointed, pointed and bedded on minimum 20mm thick cement and sand screed (13) Miscellaneous * Hack off all existing damaged rendering /finishings on floors, treads, risers etc and prepare surface to receive new finish *(D113 D115)

D113

Not exceeding 25mm thick

m2

2.40

D114

Exceeding 25mm but not exceeding 50mm thick

m2

3.40

D115

Exceeding 50 but not exceeding 75mm thick

m2

4.30

D116

Hack existing floor to form random keys, clean and wash to receive new finish

m2

1.30

D117

Scrape off existing damaged vinyl tile / carpet / linoleum and remove all adhesive stains

m2

1.80

SOR Page 9 Item D121

Description Apply one coat of approved bonding agent to concrete surface to receive new rendering / finishings. (applicable for walls and floors)

Unit m2

Rate ($) 0.80

D122

Patch up existing holes to floor rendering not exceeding 0.1 metre square in cement mortar (1:3) gauged with bonding agent top surface trowelled smooth to match existing.

No.

2.10

Patch up existing damaged mosaic floor finishings with new mosaic to match existing for single patch not exceeding 0.1 metre square

No

6.70

Re-pointing joints of existing mosaic floor in white cement including cleaning floor on completion.

m2

4.60

Re-pointing joints of existing quarry tiles/ceramic tiles/brick paving with cement and fine sand.

m2

3.80

Treatment to existing tiles/carpark ramp surface with anti-slip floor treatment chemicals according to manufacturer’s instructions.

m2

13.60

Concrete base to tube stand of fixed table/stool in hawker centres not exceeding 200mm diameter and 75mm high including mosaic/ceramic tiles, coved tiles, to match existing

No

15.00

D123 D124

D125

Epoxy Sediment Colour Flakes Coating System to Wall or Floor 41.00 D126 D127

Supply and apply epoxy sediment colour flakes coating system with 2component epoxy resin binder follow by a layer of sediment colour flakes and a non-slip 2-component polyurethane binder. (Average thickness of coating shall be 1.2mm)

m2

Repair to Concrete Surface D128

* Supply and lay approved two components patching compound mixed with liquid acrylic based additive according to manufacturer’ s instruction

D129 To floor of 4-5mm thickness

m2

16.30

To cracks in walls, slabs, soffits and floors approximately 25mm x 25mm deep including forming ‘V’ shaped grooves Supply and lay approved single component consists of special cement and synthetic aggregates according to manufacturer’s instruction

m

5.30

To floor of 4-5mm thickness

m2

16.30

To cracks in walls, slabs, soffits and floors approximately 25mm x 25mm deep including forming ‘V’ shaped grooves Supply and lay approved two components mortar based compound consists of cement, additivies, aggregates and well-graded filler mixed with liquid acrylic polymer and synthetic resin according to manufacturer’ s instruction

m

5.30

To floor of 4-5mm thickness

m2

25.60

To cracks in walls, slabs, soffits and floors approximately 25mm x 25mm deep including forming ‘V’ shaped grooves

m

6.60

D130 D131

E – NOT IN USE

F – CARPENTER, JOINER AND IRONMONGER S/N

Contents

SOR Page

1

False Ceiling

F1

2

Fire-Rated Doors

F2

3

Doors

F2 – F5

4

Windows

F5

5

Boarding

F5

6

Fire-Rated Partitions

F6

7

Bolts

F7

8

Hinges

F8

9

Hasp & Staples

F8

10

Locking Eye/Ear

F8

11

Door Holder/Closer

F8

12

Keys

F9

13

Gain Access to Units

F9

14

Door Handles

F9 – F10

15

Anchor

F10 – F11

16

Padlock

F11 – F13

17

Lockset

F13

18

Cupboard Fitments

F13

19

Sawn Timber

F14

20

Wrot Timber

F14

21

Plywood Panels

F14

22

Laminated Plastic Sheet

F15

23

Rubber Guard

F15

24

Locking Bar

F15

25

Stainless Steel Spike

F15

26

Ball Catch

F15

27

Chicks/Blinds

F16

28

Work in Connection with Demolition

F16

29

Nomad Dirt Trap Matting

F16

30

Perspex Sheet

F16 – F17

31

Miscellaneous

SOR Page F1 Item

Description

Unit

Rate ($)

m2

16.00

m2

15.00

m2

18.80

m2

23.70

m2

28.30

CARPENTER, JOINER JND IRONMONGER (To be read in conjunction with Preambles) False Ceiling F001

Supply and fix symmetrically 6mm thick asbestos-free cement board ceiling lining including all necessary timber cover fillets * Supply and fix Calcium Silicate asbestos-free building boards as ceiling board in-fill to suspended system (suspended system measured separately) or nailed to timber joints (timber joints and cover fillets measured separately) * (F002 F005)

F002

3.2mm thick

F003

6mm thick

F004

9mm thick

F005

12mm thick

F006

Supply and fix 12mm thick soft board as ceiling or wall panel (timber framing and fillets measured separately)

m2

11.80

F007

Supply and fix 12mm thick mineral fibre or plasterglass ceiling boards in-fill including “L11 shape aluminium stiffener, where necessary

m2

25.60

m2

27.00

m2

33.00

* Supply and fix fibre plastered board to lobby ceiling on timber framing support x 50mm treated timber and 50 x 25mm hanger treated timber *(F008 F009) F008

9mm thick

F009

12mm thick * Supply and fix gysum ceiling board including all necessary joint (tanalised timber frame and painting measured separately) *(F010 F011)

F0l0

9mm thick

m2

15.10

F011

12mm thick

m2

18.30

F012

Supply and fix plasterglass / gypsum cornices including all necessary joint and removal of old cornices.

m

8.20

F013

Supply and fix “TTT or “L” shaped galvanised steel strips with aluminium or enamel finishes not exceeding 30mm wide as fillet for false ceilings including hanging wires or adjustable rod hanger.

m

4.00

F014

Supply and fix 9mm thick egg crate plastic louvre for encasing gas pipe

m2

24.40

SOR Page F2 Item

Description Fire-Rated Doors

Unit

Rate ($)

F015

Supply and fix a complete system of 45mm thick single leaf half-hour fire rated timber surface finished composite door and all necessary ironmongery and accessories as specified and approved by PSB and FSB

m2

239.50

F016

Supply and fix a complete system of 45mm thick single-leaf half-hour fire rated timber surface finished composite door complete with 6mm thick wired clear glass observation panel, and all necessary ironmongery and accessories as specified and approved by PSB and FSB

m2

264.50

F017

Supply and fix a complete system of 45mm thick half-hour fire rated aluminium clad composite door for Service Duct complete with aluminium clad timber door frames and ironmongery as specified in detailed drawing (EM-TC-STD-BLDG-99-13) and approved by PSE and FSB

m2

345.00

F018

Supply and fix a complete system of 45mm thick half-hour fire rated aluminium clad composite door in two leaves for Store, Bulk Refuse Area, CD Shelter or Switch/Pump/MDF Room complete with aluminium clad timber door frames and ironmongery as specified in detailed drawing (EM-TC-STD-BLDG-99-13) approved by PSB and FSB

m2

304.80

92.00

Doors F019

Supply and install 38mm thk Framed, Ledged and Braced Door and filled in with 19mm thick tongued and grooved “V” jointed boarding as specified in drawing(EM-TC-STD-BLDG-99-14)

m2

F020

Supply and install 45mm thk Framed, Ledged and Braced Door and filled in with 19mm thick tongued and grooved “V” jointed boarding \

m2

Supply and install 50mm thk Framed, Ledged and Braced Door and filled in with 25mm thick tongued and grooved “V” jointed boarding

m2

112.70

P021

101.20

* Supply and install in the following thickness with framings slot & fix and filled in with 13mm thick timber louvres including fixing fillets *(F022 F023) F022

38mm thick

m2

80.70

F023

45mm thick

m2

86.50

F024

Supply and install 38mm thick flush door filled in on both sides with 6mm thick plywood as per drawing no. (EM-TC-STD-BLDG-99--28)

m2

68.10

* Supply and install solid cored flushed door filled in on both sides with 6mm thick plywood *(F025 P027) P025

38mm thick

m2

76.90

F026

45mm thick

m2

84.90

F027

50mm thick

m2

89.80

SOR Page F3 Item P028

F029

F030

Description Supply and install 50mm thick 2 leaf solid core timber door comprising 38mm thick tongued and grooved, jointed boards and filled in both faces with 6mm thick plywood and 19mm thick hardwood edging all round

Unit m2

Rate ($) 102.00

Supply and install 40-45mm thick half-round fire-rated single leaf decorative solid timber composite door for main entrance(door frame and stain vanished not included) complete with ironmongery approved by PSB and FSB (for door-size ranging from 850-1000mm in wide and 2100-2200mm in height)

no.

325.80

Supply and install 38mm thk switchroom door with 2 or 3 panels filled in with 9.5mm thick plywood and 1 panel with framing slot & fix and filled in with 13mm thick timber louvres including fixing fillets

m2

70.00

* Supply and install panel door in the following thickness in 4 panels filled in with 9.5mm thick plywood *(F031 F033) F031

38mm thick

m2

66.20

F032

45mm thick

m2

70.40

F033

50mm thick

m2

73.60

m2

31.50

m2

33.30

m2

35.30

* Supply and install framed cupboard door in the following thickness filled in with 6mm thick plywood *(F034 F036) F034

19mm thick

F035

25mm thick

F036

32mm thick

F037

Take down part decayed timber doors take out decayed members and incorporate new members, adjust and re-assemble door including all necessary dowels and wedges and re-fixing doors to position and removal of debris from site (New timber members measured separately)

m2

17.00

F038

Take down warped doors, ease, adjust and refix to position

m2

4.30

F039

Cut into/take out part (not whole piece of timber member) / rotten or decayed frames, mullion, transome, cills, handrails, etc and form all necessary approved joints to receive new timber including taking down of doors, if necessary and rehanging in position new timber measured separately)

m

8.00

F040

Bore holes to door panels not exceeding 25mm diameter for ventilation

No.

0.60

F041

Pull off existing nails, hooks, screws etc. from timber and fill up holes with wood putty or other approved material and touch up with paint to match existing

No.

0.40

F042

Fill up door lock holes, hinge rebates, etc with and including adhesive and timber, sand-papering and knotting, and painting to match existing

No.

2.70

F043

Supply and fix rubber glazing gasket to doors

m

3.20

SOR Page F4 Item

Description * Supply and install 1.2mm thick natural anodised extruded aluminium framed swing door G/W sheet / float glass, aluminium door framing, ironmongery and all necessary fixing, jointing and accessories *(F044 F045)

Unit

Rate ($)

F044

With 6mm thick clear sheet/float glass

m2

129.80

F045

With 6mm thick tined sheet/float glass

m2

134.60

Supply and install 1.2mm thick natural anodised extruded aluminium framed swing door with fixed top panel c/w sheet/float glass, aluminium door framing, ironmongery and all necessary fixing, jointing and accessories *(F046 F047) F046

With 6mm thick clear sheet/float glass

m2

129.80

F047

With 6mm thick tined sheet/float glass

m2

134.60

F048

Supply and install 10mm thick twin-wall tinted bronzed polycarbonate sheet onto existing frames with aluminium champing bar c/w snap on cover and all necessary accessories

m2

93.00

F049

Supply and install 12mm thick tempered glass swing door lm x 2.lm c/w ironmongery, handle including all necessary fixing, jointing and accessories

m2

847.80

F050

Supply and install 12mm thick tempered glass for door and full height glass partition

m2

192.20

F051

Supply and install 12mm thick glass for door and full height glass partition

m2

228.30

F052

Labour to take down tempered glass door to clean, oil all mechanism and refix in position with proper alignment

m2

11.20

F053

Labour for checking and repair auto sliding door (cost of parts shall be paid separately)

no.

207.00

F054

Supply and fix wide angle door viewer

no.

7.30

F055

Supply and fix door seal

m

5.90

F056

Supply and fix stainless steel security door chain and slot

no.

10.80

F057

Supply and fix chrome security door chain and slot

no.

8.50

Kapor casement or door panels open to receive glass, waterproof plywood or wire gauze with rebated and moulded rails, stiles, glazing or dividing bars and pinned heads including hanging on to door frames(infills panels measured separately) *(F055 F06l) F058

25mm thick

m2

56.70

F059

38mm thick

m2

63.40

F060

43mm thick

m2

67.10

F061

48mm thick

m2

70.90

SOR Page F5 Item

Description Kapor panelled casements or doors partly panelled with solid timber or plywood not exceeding 12mm thick partly open for glazing with rebated and moulded rails, stiles, glazing beads including hanging on to door frames (Glass panel measured separately) *(F062 F066)

Unit

Rate ($)

F062

25mm thick

m2

64.30

F063

38mm thick

m2

71.80

F064

43mm thick

m2

74.70

F065

48mm thick

m2

78.50

m

2.10

m2

75.00

m2

56.10

m2

17.00

WINDOWS F066

F067

Supply and fix back vinyl gester sealing strips to perimeter of window frame with holding down screws or nails at 50mm centre Supply and install 38mm thick windows with framings stop slotted and filled in with 13mm thick timber louvres including fixing fillets Supply and install 38mm thick framed windows open rebated and prepared for glass including fixing beadings (glass measured separately)

F068

F069

Take down part decayed timber windows take out decayed members and incorporate new members, adjust and re-assemble windows including all necessary dowels and wedges and re-fixing windows to position and removal of debris from site (New timber members measured separately)

F070

Take down warped windows, ease, adjust and refix to position

m2

8.10

F071

Cut into/take out part (not whole piece of timber member), rotten or decayed frames, mullion, transome, cills, handrails, etc and form all necessary approved joints to receive new timber including taking down of windows, if necessary and rehanging in position new timber measured separately)

m

8.00

F072

Supply and fix rubber glazing gasket to Notice Board, sliding windows, top hung and casement windows

m

3.80

F073

Supply and fix 300mm long chromium plate casement studs

no.

5.60

F074

Supply and fix black Japenned casement studs

no.

1.80

F075

Supply and fix chromium plated casement fasteners

no.

4.50

Boarding Wrot kapor boarding to floors, shelves, fitments, partitions, ceiling, etc. well cramped up, nailed or screwed to bearers (Bearers measured separately) *(F076 F079) F076

19mm thick

m2

31.60

F077

25mm thick

m2

41.60

F078

28mm thick

m2

46.50

F079

38mm thick

m2

63.20

SOR Page F6 Item

Description Fire Rated Partition

Unit

Rate ($)

F080

Supply and install one-hour fire rated partitions both sides covered with approved 15mm thick gypsum boards constructed with ‘U’ channel frame including all accessories & necessary works (dismantling of existing false ceiling, partitions, diversion of services, painting and other finishes measured separately)

m2

30.80

F081

Supply and install half-hour fire rated partitions both sides covered with approved 12mm thick gypsum boards constructed with ‘U’ channel frame including all accessories & necessary works (dismantling of existing false ceiling, partitions, diversion of services, painting and other finishes measured separately)

m2

25.20

F082

Supply and fix in replacement approved 15mm thick gypsum board to existing fire rated partitions including dismantling of existing false ceiling and re-fix in position, if applicable. Remove debris and make good work disturbed (diversion of services, painting and other finishes measured separately)

m2

11.70

F083

Supply and install 50mm thick half-hour rated solid kapor timber door constructed with T & G boardings and flush jointed with 3 nos. of 10mm diameter mild steel tie rods including wired glass peephole (painting and ironmongery measured separately)

m2

97.20

F084 to F093 NOT IN USE

SOR Page F7 Item

Description

Unit

Rate ($)

Bolts F094

75mm long brass barrel bolts

No.

1.80

F095

100mm long brass barrel bolts

No.

1.90

F096

150mm long brass barrel bolts

No.

2.20

F097

250mm long brass barrel bolts

No.

3.20

F098

300mm long brass barrel bolts

No.

4.30

F099

450mm long brass barrel bolts

No.

6.90

F100

90mm x 27mm stainless steel barrel/square shoot bolt

No.

7.70

F101

240mm x 27mm stainless steel barrel/square shoot bolt

No.

9.00

F102

100mm stainless steel flush shoot bolt

No.

10.60

F103

150mm x 25mm stainless steel flush shoot bolt

No.

9.30

F104

225mm x 25mm stainelss steel flush shoot bolt

No.

9.90

Japenned malleable iron cabin hooks and eyes *(F105 F110) F105

75mm

No.

2.00

F106

150mm

No.

2.50

F107

225mm

No.

3.80

F108

300mm

No.

5.20

F109

375mm

No.

8.00

F110

450mm

No.

8.90

SOR Page F8 Item

Description Hinges *(F111 F115)

Unit

Rate ($)

F111

75mm pressed steel butt hinges

No.

1.60

F112

100mm pressed steel butt hinges

No.

1.90

F113

150mm pressed steel butt hinges

No.

2.20

F114

100mm stainless steel butt hinges

No.

10.50

F115

150mm stainless steel butt hinges

No.

14.70

* Supply and fix HEAVY DUTY HOOK AND BAND HINGES to bin compound door * (F116 F117) F116

600mm

No.

28.50

F117

750mm

No.

33.10

Hasp & Staple F118

Supply and fix heavy duty galvanised hasp and staple for roof trap door

No.

9.50

F119

Supply and fix 50mm long aluminium or galvanised mild steel hasp and staple for notice board or other uses

No.

1.60

F120

Supply and fix 75mm long aluminium or galvanised mild steel hasp and staple for notice board or other uses

No.

1.50

Locking Eye/Ear F121

Supply and fix 12/25mm diameter galvanised steel diameter locking eye to pad bolts

No.

1.60

Fl22

Supply and fix 100mm x 60mm x 3mm stainless steel plate as locking ear to switch room, pump room etc.

No.

8.80

F123

Supply and fix 75 x 38 x 3mm stainless steel plate as locking eye to switchroom, pumproom, etc.

No.

8.30

Door Holder/Closer F124

Supply and fix spherical magnetic door holder

No.

6.00

F125

Supply and fix 38mm diameter rubber door stop

No.

1.40

F126

Supply and fix of “Yale” Model lite 2 auto-retractable hydraulic door closer including refixing, adjusting to position

No.

33.70

F127

Supply and fix “Union” Model 8573/8173 door closer including refixing, adjusting to position

No.

62.90

F128

Supply and fix door closer “Dorma TS 73”

No.

139.40

F129

Supply and fix door closer “Dorma TS 73V/BC

No.

155.20

F130

Supply and fix door “Dorma ETS 8411 non-hold floor spring c/w door strap including alignment of glass door

No.

327.60

SOR Page F9 Item

Description Keys

Unit

Rate ($)

F131

Supply “Abloy” key in duplicate

No.

4.60

F132

Supply only duplicate keys to match existing

No.

2.30

F133

Supply and cut one key to lock with missing keys including taking out lock, where necessary and refix same

No.

9.70

Gain Access To Units F134

Open door to gain access into premises where keys have been lost

Door

7.40

F135

Provide locksmith for gaining access to premises without damaging the lock

Door

50.00

Door Handles F136

Supply and fix YTL-75 or other approved stainless steel cup handle for pumproom, switchroom, service duct door, etc.

No.

12.90

F137

Supply and fix YTL-85 or other approved stainless steel cup handle passage latch for service duct door with cup handles on both sides

No.

34.80

F138

Supply and fix “U-shaped” stainless steel handle (225 x 57 x 19mm) to door

No.

31.20

F139

Supply and fix stainless steel push plate (150 x 300 x 1.5mm thick) to door

No.

29.00

F140

Supply and fix 75 x 25mm aluminium flush pull

No

3.70

F141

Supply and fix 100 x 50mm aluminium flush pull

No.

4.00

F142

Supply and fix 150mm aluminium handle fleet “Delta 2553”

No.

7.10

F143

Supply and fix 250mm aluminium handle

No.

20.30

F144

Supply and fix “Delta” stainless steel handle

No.

32.80

F145

Supply and fix 100mm stainless steel bow handle

No.

5.10

F146

Supply and fix 100mm brass handle

No.

4.50

Anchors * Supply and fix “HILTI-HVA” or other approved adhesive anchor including drilling holes and all necessary preparation according to manufacturer’s instructions *(F147 Fl54) F147

8mm diameter x 110mm long galvanised steel anchor inclusive of adhesive cartridge

No.

8.10

F148

10mm diameter x 130mm long galvanised steel anchor inclusive of adhesive cartridge

No.

9.50

F149

12mm diameter x 160mm long galvanised steel anchor inclusive of adhesive cartridge

No.

10.90

F150

16mm diameter x 190mm long galvanised steel anchor inclusive of adhesive cartridge

No.

14.70

SOR Page F10 Item F15l

Description 8mm diameter x 110mm long stainless steel anchor inclusive of adhesive cartridge

Unit No.

Rate ($) 13.00

F152

10mm diameter x 130mm long stainless steel anchor inclusive of adhesive cartridge

No.

16.30

F153

12mm diameter x 160mm long stainless steel anchor inclusive of adhesive cartridge

No.

19.20

F154

16mm diameter x 190mm long stainless steel anchor inclusive of adhesive cartridge

No.

30.20

* 5mm thick stainless steel eye anchor of internal diameter 15mm of Grade AISI 304 complete with stainless steel spacer *(F155 F157) F155

Supply eye-anchor only as specified

No.

2.30

F156

Supply and fix eye-anchor as specified including drilling of holes, epoxy putty and approved nylon plug

No.

7.40

F157

Supply and fix eye-anchor as specified including epoxy putty and approved nylon plug but exclude drilling of holes

No

6.30

F158 to F159 NOT IN USE Padlocks * Supply only “Yale’ brass cylinder padlock complete with 2 keys *(F161 Fl65) F161

30mm

No.

11.50

F162

40mm

No.

12.00

F163

50mm

No.

16.10

F164

60mm

No.

22.40

F165

70mm

No.

36.20

* Supply and deliver padlock with key alike system (I key for every 5 nos. of lock) *(F166 F175) F166

Abloy Model (PL 320/20)

No.

54.30

F167

Abloy Model (PL 3020)

No.

20.60

F168

Abloy Model (PL 330/50)

No.

37.40

F169

Abus Model 55 MB/30

No.

6.80

F170

Abus Model 55 MB/40

No.

8.60

SOR Page F11 Item F171

Description Abus Model 55 MB/50

Unit No.

Rate ($) 12.60

F172

Abus Model 27/50

No.

66.00

F173

Rocket Model ATS 30

No.

13.80

F174

Rocket Model ATS 40

No.

16.50

F175

Rocket Model ATS 50

No.

22.20

F176

Supply 300mm long chain/ring fixed to metal box, door etc for padlock

No.

2.70

Locksets F177

Supply and fix cam lock (Yale Model No. 490.25) for letter box or other uses including spot weld the locking nut, where necessary

No.

13.30

F178

Supply and fix approved master lock to door behind letter boxes

No.

14.20

F179

Supply and fix lock for notice board

No.

12.50

F180

Supply and fix Yale” 513/ 32626 single cylinder mortice dead lock

No.

60.40

F181

Supply and fix cylinder rim drawback locks (‘Union” 1332-SE, “Yale” No. 1 or other approved) complete with 3 keys

No.

49.90

F182

Supply and fix cylinder mortice lockset complete with stainless steel handle (“Union” 643/46/41, “Showa” CL-05-240 or other approved)

No.

64.80

F183

Supply and fix double cylinder mortice lockset. with stainless steel handle (“Union” 643/46/241, “Showa” CL-26-240 or 6ther approved)

No.

70.60

F184

Supply and fix brass cupboard or drawer locks of approved quality

No.

9.90

F185

Supply and fix sashlock to aluminium sliding window

No.

13.10

F186

Supply and fix aluminium or zinc die cast crescent lock to aluminium sliding window

No.

4.40

F187

Supply and fix single cylinder mortice lock “Union” 2441, “Yale” 514/32626 or other approved to aluminium sliding door

No.

63.70

F188

Supply approved dial face number combination lock

No.

10.40

F189

Supply and fix lockset to aluminium sliding door (“Alboy 2260” or other approved)

No.

121.60

F190

Supply and fix “Union” 8098 or other approved indicating bolt for toilet door

No.

13.70

SOR Page F12 Item

Description * Supply and install cylinder mortice night latch for fire-rated Service Duct Door, etc complete with stainless steel cup handle, provision of keys including all fixing accessories: *(Fl9l F194)

Unit

Rate ($)

F191

Accord 2332/1405 under MK and master key series MK48

No.

68.40

F192

Forte H6RP75ES under PA master key series MK48

No.

61.70

Fl93

Union 2332 CH/300/2xl3 under GIHG-PH and master key series GIHBG

No.

79.10

F194

Yale 3203A/214.62 under MKAA and master key series MK48

No.

74.20

F195

Supply and install cyclinder mortice night latch lockcase “Accord 2332/1405”

No.

45.20

F196

Supply and install cyclinder mortice night latch lockcase “Forte H6RP75ES”

No.

35.40

F197

Take out locks, repair, oil and ease lock and refix to position

No.

7.40

F198

Supply and fix double cylinder mortice lockset c/w handle Abloy 4190”

No.

150.80

F199

Supply and fix single cylinder thumbturn lockset to aluminium sliding door “Alboy 4960”

No.

163.40

F200

Supply and fix double cylinder mortice lockset “Accord O7O6PZ/l591/1406”

No.

98.60

F201

Supply and fix double cylinder mortice lockcase “Accord O7O6PZ”

No.

46.50

F202

Supply and fix lockset for tempered glass door “Accord US1O/1406””

No.

317.30

F203

Supply and fix door spring for tempered glass door ‘Accord 853” including alignment of glass doors

No.

243.80

F204

Supply and fix cylinder knot set (5 Pin tumbler) “Goal US 5E”

No.

33.60

F205

Supply and fix privacy knobset with emergency release “Goal US 4E”

No.

29.50

F206

Supply and fix passage knob latch set “Goal US 1E”

No.

27.80

F207

Supply and fix cylinder/tumbler turn deadbolt “Goal ADP-5/70-ll”

No.

40.50

F208

Supply and fix single cylinder knobset (5-pin tumbler) “Lucky 1000”

No.

20.90

F209

Supply and fix privacy knobset with emergency release “Lucky 1030”

No.

20.90

F210

Supply and fix passage knot latchset “Lucky 1082”

No.

19.90

F211

Supply and fix single cylinder knobset(5-pin tumbler) “Posse 100-SS”

No.

22.10

F212

Supply and fix knobset with emergency release “Posse 130-SS”

No.

22.10

F213

Supply and fix passage knot latchset “Posse 182”

No.

19.80

F214

Supply and fix single cylinder deadbolt “Posse Dll8 SS”

No.

35.90

F215

Supply and fix single cylinder deadbolt c/w inside thumbturn “Yale 8211”

No.

27.90

SOR Page F13 Item F216

Description Supply and fix double cylinder brass antique finish gip handle and knob “Posse H613 AB” or Hafele series 1300”

Unit No.

Rate ($) 86.70

F217

Supply and fix doable cylinder mortice lockset c/w handle “Trident 9000/1520/810”

No.

94.50

F218

Supply and fix single cylinder knobset (5-pin tumbler) “Union 9308-SS”

No.

24.40

F219

Supply and fix double cylinder mortice lockset c/w handle “Union 675-4l278SS”

No.

92.60

F220

Supply and fix privacy knobset (5-pin tumbler) “Union 9301-SSO”

No.

21.90

F221

Supply and fix passage knob latchset ”Union 9302-SS”

No.

20.60

F222

Supply and fix double cyclinder mortice lockset c/w handle “Yale 138L/520.50/210.62”

No.

77.80

F223

Supply and fix cyclinder mortice lockset with cast aluminium chrome plated level handle “Yale l3BL/520.40/2l0.66”

No.

77.80

F224

Supply and fix mortice dead lock “Yale 197”

No.

80.60

F225

Supply and fix L315A/M246/21/2”

No.

27.90

F226

Supply and fix lock to roller shutter “Viro 8202/8203” or other approved

No.

27.30

F227

Labour for taking out lock from tempered glass door, repair, oil and ease lock and refix in position

No.

9.80

aluminium

finish

mortice

level

lockset

“Yale

Cupboard Fitments F228

Refix loose sliding track of cupboard fitments

m

0.80

F229

Supply and fix plastic drawer track for cupboard fitments (one side)

no.

7.70

F230

Supply and fix PVC coated metal drawer track c/w roller for cupboard fitments

no.

6.00

F231

Supply and fix 20mm diameter brass cupboard dead knob

no.

3.00

m3

1633.60

Sawn Timber F232

Supply and fix Sawn Kapoh or Keruing in wall plates, rafters, purlins, or joists, collars, etc. including tanalising or two coats wood preservative * Supply and fix Sawn Kapoh or Keruing batten for tiles including tanalising or two coats wood preservative *(F233 F236)

F233

50mm x 25mm

m

1.10

F234

50mm x 40mm

m

1.90

F235

75mm x 25mm

m

1.80

F236

50mm x 50mm

m

2.20

F237

Handrails not exceeding 500m2 in sectional area

m

15.70

SOR Page F14 Item

Description Wrot Timber

Unit

Rate ($)

* Supply and fix Wrot Kapoh or Keruing *(F238 F243) F238

Fascia or barge boards

m3

1588.00

F239

Frame, head, mullion, transome, handrails, cill or boarding worked to the required shape

m3

1780.30

F240

Moulded architraves, cover fillets, etc not exceeding 500 sq mm in sectional area

m

1.50

F241

Moulded architraves, cover fillets, etc exceeding 500 sq mm and not exceeding 1,000 sq mm in sectional area

m

2.20

F242

Louvre blades or moulded skirtings not exceeding 2,000 sq mm sectional area

m

4.10

F243

Louvre blades exceeding 2,000 sq mm and not exceeding 4,000 sq mm sectional area

m

4.10

* Supply and fix Wrot timber worked to the required shape in small quantities not exceeding 0.5m3 per job using *(F244 F246) F244

Wrot Chengal

m3

2815.70

F245

Wrot Balau

m3

1984.10

F246

Wrot Kapor

m3

1984.10

Plywood Panels * Supply and install Approved Waterproofed (WEP) PLYWOOD in panels *(F247 F252) F247

6mm thick

m2

13.60

F248

9mm thick

m2

15.70

F249

12mm thick

m2

18.00

F250

15mm thick

m2

19.80

F251

18mm thick

m2

24.80

F252

25mm thick

m2

30.40

Laminated Plastic Sheets * Supply and install approved LAMINATED PLASTIC SHEETS (“STANDARD” quality) to existing surfaces with approved adhesive compound including preparation of surfaces *(F253 F254) F253

1.2mm thick

m2

27.40

F254

0.8mm thick

m2

23.60

SOR Page F15 Item

Description Rubber Guard

Unit

Rate ($)

F255

Supply and fix 150mm x 30mm thick rubber protection guard with 2 nos. HRD-N fastener screws at 500mm centre to centre to walls of dustbin compound

m

51.80

Locking Bar * Purpose made mild steel locking bar out of 12mm/2Smm diameter mild steel rod welded to flat handle with slot Including all necessary hooks and shoots *(F256 F259) F256

250mm long weld to 50mm x 100mm x 5mm thick flat handle

No.

11.70

F257

300mm long weld to 50mm x 100mm x 5mm thick flat handle

No.

12.30

F258

360mm long weld to 75mm x 100mm x 5mm thick flat handle

No.

14.30

F259

460mm long weld to 75mm x 100mm x 5mm thick flat handle

No.

15.10

No.

2.70

F260 to F261 NOT IN USE Stainless Steel Spike F262

Supply and fix 13mm long stainless steel sike sharpen from 3.2mm diameter rod complete with 35mm x 15mm x 3mm base plate including all necessary fixing accessories Ball Catch

F263

Supply and fix 60mm brass or satin nickel double ball catch to door, etc

No.

8.20

F264

Supply and fix 2 pairs of 60mm brass or satin nickel double ball catch to service duct door including removing existing night latch lockset, patching, painting and making good affected area

Door

17.60

Chicks/ Blinds F265

Supply and install unlined split chicks constructed with ropes of No.8 white glazed cord or nylon cord, 25mm diameter galvanised pulleys secured to galvanised screws, hooks, size 18mm x 100mm brass clear fixed with brass screws

m2

26.90

F266

Extra over for item F258 to paint one side with one coat of primer, 1 undercoat and 1 finishing coat of enamel paint

m2

3.60

F267

Extra over for item F258 to line one side with first quality approved bluedrill cloth or plastic cloth including binding the edge and allowance for all cutting

m2

3.60

SOR Page F16 Item

Description Work In Connection With Demolition

Unit

Rate ($)

* Seal up existing doors, windows, vents, etc. to vacant structures with approved quality timber comprising 38mm x 75mm main framings and 2 numbers 25mm x 75mm diagonal struts and filled in with 20mm x 100mm horizontal boarding at 150mm centres to openings of the following sizes *(F268 271) F268

Not exceeding 1.0m2

No.

16.30

F269

Exceeding l.0m2 but not exceeding 1.5m2

No.

21.50

F270

Exceeding l.5m2 but not exceeding 2.0m2

No.

25.20

F271

Exceeding 2.0m2 but not exceeding 2.5m2

No.

29.70

F272

Seal up existing shop fronts, etc exceeding 2.5m2 to vacant structures with approved quality timber comprising 38mm x 75mm main framings (vertical frames not more than 1500mm apart) and 2 numbers 25mm x 75mm diagonal struts between vertical frames and filled in with 20mm x 100mm horizontal boarding at 150mm centres

m2

10.70

F273

Supply and erect 1.20rn high sawn timber fencing to be constructed with 100mm x 100mm posts at 3.0Cm centres, 2 nos. of 100mm x 50mm horizontal runners and 100mm x 20mm vertical boarding at 200mm centres. The footings for posts shall be 225mm x 225mm x 300mm concrete (1:3:6) . The whole fencing shall be strengthened with 100mm x 50mm slanting struts at every alternate post. Bottom end of struts shall be cast in 225mm x 225mm x 225mm footing and top end secured to post. Prepare and apply one coat of emulsion paint to both sides of fencing

m

41.30

m2

78.70

m2

38.60

m2

101.00

Normad Dirt Trap Matting F274

Supply and install ‘3M’ nomad dirt trap matting c/w “WELCOME” lettering at centre Perspex Sheet Supply and install clear Perspex sheet including preparation of surfaces

F275

3mm thick

F276

12mm thick Miscellaneous

F277

Take out serviceable hinges, locks, bolts etc and refix to new doors/windows etc.

No.

2.00

F278

Supply and fix pop rivets to aluminium louvre blade or other aluminium fittings

No.

0.40

F279

Supply and fix “Hilti” or other approved raw plug including use of gun and explosive charges

No.

2.40

F280

Refix wall mounted bin including all necessary drilling, fixing screws, rivet, bolts, nuts, etc.

No.

3.70

SOR Page F17 Item F281

Description Supply and install 250 x 250 x 3mm thick acrylic toilet side surface mounted on door, wall, etc.

Unit No.

Rate ($) 32.70

F282

Supply and install PVC curtain strip 300 x 2500 x 3mm thick, complete with stainless steel bolts and nuts. 50% overlapping. Size 1900 x 2500

No.

380.00

G – STEEL AND IRONWORKER S/N

Contents

SOR Page

1

Rainwater Downpipe

G1

2

Gratings

G1 – G4

3

Welding

G4

4

Flashing

G5

5

Expansion Joints

G5 – G6

7

Doors

G6 – G8

8

Gates

G8

11

Windows

G8 – G11

12

Ceiling

G11 – G12

13

Mild Steel Elements

G12

14

Signage

G12

16

Chequered Plate

G13 – G14

18

Mild Steel Door Frame

G14

19

Mild Steel Entrance Gate

G14

22

Notice Board

G14

23

Wrought Iron Holdfast

G15

28

Ramset Nail

G15

29

Staircase Nosing

G15

30

Catladder

G15

31

Flushout Pipe

G15

32

Stainless Steel Pipe Socket

G16

34

Stainless Steel Members

G16

35

Metal Sunlourves

G16

37

Miscellaneous

G16

38

Supplementary

G17

SOR Page G1 Item

Description STEEL AND IRONWORKER (To be read in conjunction with the Preambles)

Unit

Rate ($)

G001 to G008 NOT IN USE Rainwater Downpipe Supply labour only for re-fixing loose brackets of rainwater down pipes. Gratings G009

Supply and fix hot-dipped galvanised steel drain cover grating for concealed drain, hinged on one side and overall 35mm thick fabricated with 25mm x 5mm intermediate flats spaced at 25mm centres resting on 10mm diameter cross bar and support on 64mm x 38mm x 4.6mm angle galvanised frame anchored to structure with fish tail complete with locking bar

No

1.70

G010

* Supply and install mild steel vertical grating to 150mm wide scupper drain surface water channel of the following depth comprising 10mm diameter yertical bars spaced 38mm centre to centre, all framed up and welded to 19mm x 19mm x 3mm thick angle horizontal top piece and 25mm x 3mm thick flat intermediate piece, the ends of horizontal top piece split and fixed to sides of channel including 2 coats of bituminous paint. *(G011 G012)

m2

170.30

G011

Not exceeding 450mm deep

No

16.10

G012

Exceeding 450mm but not exceeding 750mm deep

No

21.90

SOR Page G2 Item

Description * Supply and install mild steel vertical grating to surface water channel exceeding 150mm but not exceedin 225mm wide of the following depth comprising 10mm diameter vertical bars spaced 38mm centre to centre, all frame up and welded to 25mm x 25mm x 5mm thick angle horizontal top piece and 25mm x 5tn thick flat intermediate piece, the ends of horizontal top piece split and fixed to sides of channel including 2 coats of bituminous paint. *(G013 G014)

Unit

Rate ($)

G013

Not exceeding 450mm deep

No

11.80

G014

Exceeding 450mm but not exceeding 750mm deep

No

15.50

* Supply and install mild steel vertical grating to surface water channel exceeding 225mm but not exceeding 300mm wide of the following depth comprising 10mm diameter vertical bars spaced 38mm centre to centre, all framed up and welded to 25mm x 25mm x 5mm thick angle horizontal top piece and 25mm x 5mm thick flat intermediate piece, the ends of horizontal top piece split and fixed to sides of channel including 2 coats of bituminous paint. *(G0l5 G0l6) G015

Not exceeding 450mm deep

No

19.00

G016

Exceeding 450mm but not exceeding 750mm deep

No

24.00

G017

Supply and fix galvanised steel wire balloon grating to top of 75mm to 150mm vent pipes including spring clips and 1 coat of bituminous paint.

No

4.10

Railings * Supply and fix Galvanised Steel Class ”A” Pipes of the following (internal diameter) as railings in two horizontal rows and vertical supports at not exceeding l.50m centres, bent to shape, necessary welding and filing smooth all welded joints, cast in 200 x 200 x 300mm deep concrete (1:2:4) foundation, painted with 1 priming coat, 1 undercoat and 1 finishing coat *(G018 G022) G018

30mm diameter

m

19.50

G019

40mm diameter

m

22.10

G020

50mm diameter

m

27.10

G021

65mm diameter

m

33.70

G022

75mm diameter

m

39.10

* Supply and fix Class “B” galvanised steel pipe of the following (internal diameter) as railing in two horizontal rows, mild steel angle upstand at not exceeding 2.5m centres, cast in 250 x 250 x 300mm deep concrete (1:2:4) foundation, painted with 1 priming coat, 1 undercoat and 1 finishing coat *(G023 G025) G023

40mm diameter but with 65 x 65 x 6mm mild steel angle

m

26.90

G024

50mm diameter but with 75 x 100 x 10mm mild steel angle

m

36.90

G025

65mm diameter but with 88 x 113 x 10mm mild steel angle

m

49.30

SOR Page G3 Item G026

Description Supply and install 50.8mm (external diameter)3mm thick grade 304 stainless steel pipe as railing with 25.4mm (external diameter) stainless steel supports spaced at not exceeding 1200mm centres including welding and necessary polishing.(For railing without bend) (Drawing No. EM-TC-STD-BLDG-00-29A)

Unit m

Rate ($) 28.30

G027

Supply and install 38mm external diameter 2mmthick Grade 304 stainless steel handrail complete with 25.4mm external diameter stainless steel supports spaced at not exceeding 1200mm centres and cast into reinforced concrete structure including all necessary bending, welding and cutting (Drawing No.. EM-TC-STD-BLDG-00-29A)

m

34.50

Supply and install 2mm thick stainless steel handrail with 25.4mm external diameter stainless steel supports spaced at not exceeding 1000mm centres complete with 120mm diameter x 4.5mm thick stainless steel plate and 3 nos. 5mm diameter raw bolts plugged onto wall for each support including all necessary bending and cut (Drawing No. EM-TC-STD-BLDG-00--029A) *(G028 G030) G028

31.8mm diameter

m

33.70

G029

38mm diameter

m

40.25

G030

50.8mm diameter

m

43.70

G031

Supply and install stainless steel railing to parapet comprising of 40 x 40 x 2mm thick grade 304 stainless steel hollow section welded with 30 x 6mm thick grade 304 stainless steel flat supports spaced at not exceeding 1000mm centres and cast into concrete structure as specified including all necessary bending and cutting

m

41.70

G032

Remove only and cart away existing railing including upstand in two horizontal rows with or without mild steel angle upstand.

m

4.30

G033

* Supply and fix 2mm thick grade 304 stainless steel hand railing in the following external diameters not exceeding 1.1m in height in two horizontal rows including vertical upstands at not exceeding 1.2m centres, necessary elbows at corners, finished smooth and polishing, cast in 200 x 200 x 300mm deep concrete(1:2:4) foundation (if necessary), including all necessary excavation, hacking, removal of debris and reinstatement works including all necessary bending and cutting *(G033 G035) 38mm

m

115.20

G034

50.8mm

m

128.10

G035

76mm

m

147.50

G036

* Supply and fix 2mm thick Grade 304 stainless steel pipe in the follow external diameters welded to narrow the gap of the horizontal rows for stainless steel hand railing including all necessary bending and cutting *(G036 G039) 50.8mm - 2mm thk

m

30.30

G037

38mm - 2mm thk

m

23.80

G038

25.4mm - 1.5mm thk

m

13.50

G039

19mm - 1.2mm thk

m

10.70

SOR Page G4 Item G040

Description Supply, fabricate and install G304 stainless steel tubular, dented G304 stainless steel tubular, square or rectangular hollow section of any size, with circumference/girth n.e. 200mm including welded joints for staircase railing/boundary railing/parapetrailing/etc. (7,93 kg/m2 per 1mm thick)

Unit Kg

Rate ($) 14.20

G041

Extra over for Item G040 for bending corner

Per Bend

28.70

G042

Supply, fabricate and install G304 stainless steel flat bar for sectional area n.e. 400 mm2 including welded joints for staircase railing/ boundary railing/parapet railing/ etc.(7.93 kg/m2 per 1mm thick)

Kg

10.70

G043

Supply and install aluminium low jail bar barrier in powder coated or anodised finish including excavation, concrete foundation and disposal of excavated materials off site (Drawing no. EM-TC-STD-BLDG-0102-07)

m

212.00

G044

Supply and install aluminium low jail bar barrier in powder coated or anodised finish including aluminium cast base with anchorage bolts (Drawing no- EM-TC--STD-BLDG-0102-07)

m

231.00

G045

Supply and install aluminium Double Row Guard Rail in powder coated or anodised finish including excavation, concrete foundation and disposal of excavated materials off site (Drawing no. EM-TC-STD-BLDG-0102-06)

m

117.00

G046

Supply and install aluminium Double Row Guard Rail in powder coated or anodised finish including aluminium cast base with anchorage bolts (Drawing no. EM-TC-STD-BLDG-0l02-06)

m

135.00

G047

Extra over for additional horizontal row to Double Row Guard Rail

m

23.00

G048

Extra over for additional horizontal or vertical diskonnect for turnings

No.

40.00

Welding G049

Weld loose, corroded or new steel work including the provision of welding rods, plant etc filing smooth, repainting to match existing and the cutting and removal of corroded parts, if any. (New steel work measured separately)

m

17.10

G050

Spot welding for steel work

No

0.70

G051

Weld loose or new stainless steel members including the provision of stainless steel welding rods/ wires, brazing/welding plants etc and filing smooth and polishing(stainless steel measured separately)

m

21.50

G052

Spot welding for stainless steel work ‘

No

0.80

G053 to G064 NOT IN USE

SOR Page G5 Item

Description

Unit

Rate ($)

Flashing * Supply labour only for REFIXING LOOSE FLASHING including all necessary additional drive screws. *(G065 G066) G065

Not exceeding 300mm girth

m

3.10

G066

Exceeding 300mm girth

m

3.80

G067

Supply and fix 0.996mm B.G. purpose-made aluminium not exceeding 300mm girth to top of windows fixed with nails at 150mm centres to timber frames including washers and sealing up joint with “Evomastic” or other approved sealing compound.

m

11.80

G068

Supply and fix 0.996mm B.G. purpose-made aluminium flashing not exceeding 300mm girth fixed to wall with masonry or ramset nails at 150mm centres including cutting groove in wall to receive edge of flashing, patching up with cement mortar and painting to match existing.

m

14.80

G069

Refix loose galvanised steel/aluminium window flashing with masonry or ramset nails at 150mm centres including re-cutting groove in wall and patching up with cement mortar and painting to match existing.

m

4.10

* Supply and fix aluminium sheeting as cover, linings and flashing to roof trap doors etc, including bending to required shape, aluminium nails/screws and washers *(G070 G072) G070

1mm thick

m2

25.50

G071

2mm thick

m2

49.00

G072

3mm thick

m2

72.60

Expansion Joints * Supply and fix 0.711mm B.G. purpose-made aluminium expansion joint cover with “VI’ shaped groove in centre including masonry nails with washers *(G073 G074) G073

Not exceeding 200mm girth

m

9.30

G074

Exceeding 200mm girth but not exceeding 300mm girth

m

17.60

G075

Refix loose aluminium expansion joint covers to walls including masonry nails and washers at approximately 150mm centres at both edges.

m

2.20

G076 to G112 NOT IN USE

SOR Page G6 Item

Description Doors

Unit

Rate ($)

G113

Supply and fix 1.219mm thk aluminium WC/bathroom doors of size not exceeding 850 x 1800 including hook and band hinges, mild steel cotter pins and brass shoot bolts/cabin hook.

No

108.00

G114

Supply and fix 1.219mm thk aluminium WC/bathroom doors of size not exceeding 850 x 1800 height including hook and band hinges, mild steel cotter pins and brass shoot bolts/cabin hook.

No

89.10

G115

Supply and fix mild steel hook for aluminium wc bathroom door hinge

No

5.70

SOR Page G7 Item G116

Description Supply and fix mild steel strap hinge including pop-rivetting to W.C./bathroom door.

Unit No

Rate ($) 4.00

G117

Supply and fix aluminium strap hinge including pop-rivetting to W.C./ bathroom door.

No

4.30

G118

Supply and fix approved aluminium strap locking bars of sizes 75mm to 200mm long to hawker stalls aluminium door including additional aluminium plate backing and pop-riveting.

No

6.10

G119

Supply and fix 50mm thick access trap door to RC roof overall size 1150 x 1150mm comprising 1.2mm thick anodised aluminium alloy sheets on both faces supported with 38 x 20 x 1.2mm thick galvanised steel channel bracings and 60 x 38 x 1.2mm thick galvanised steel “C11 channel framings infilled with rockwool insulation including approved hasp and staple, brass rollers to manufacturer’s details in drawing (EM-TC-STD-BLDG-99-15, 16 & 17)

No

449.20

G120

Supply and fix plastic roller to roof access door

No

11.70

* Supply and fix natural anodised aluminium sliding door (from approved manufacturers) complete with sheet glass and all necessary fixtures and fixing accessories. *(G121 G122) G121

With 6mm thick clear sheet glass.

m2

100.50

G122

With 6mm thick tinted sheet glass.

m2

105.40

G123

Supply and fix mild steel Sliding and Folding Door including all necessary fixtures, accessories and 1 priming coat and 2 finishing coats of enamel paint to match existing.

m2

171.10

* Supply and fix natural anodised aluminium framed with glass panel DOOR from approved manufacturers complete with all necessary fixtures and fixing accessories etc (lockset, floor spring and door closer measured separately) *(G124 G125) G124

With 6mm thick clear sheet glass

m2

188.00

G125

With 6mm thick tinted sheet glass

m2

209.80

* Supply and fix in replacement natural anodised aluminium framed FIXED PANEL from approved manufacturers complete with all necessary accessories, etc *(Gl26 Gl27) G126

With 6mm thick clear sheet glass

m2

165.00

G127

With 6mm thick tinted sheet glass

m2

170.80

G128

Supply and fix aluminium fixed full louvred door complete with 2.3mm thick extruded aluminium louvred blades including all necessary fixing accessories (Door frame to be measured separately) (EM-TC-STD-BLDG-99-l9)

m2

257.60

G129

Supply and fix mild steel door frame including fishtail holdfast

m

31.80

G130

Supply and fix anodised aluminium half louvred and half panel door including stainless steel or brass butt hinges and all necessary ironmongery

m2

283.30

SOR Page G8 Item G131

Description Supply and fix 100 x 25 x 2.3mm thk aluminium door frame with 13mm wide inner stopper frame including plastering and painting (exclude Hinges)

Unit m

Rate ($) 32.80

G132

Supply and fix approved PVC door not exceeding 1.70m2 complete with lockset and necessary fixtures

No

120.40

G133

Supply and fix approved PVC door not exceeding 1.7 m2 but not exceeding 2.1m complete with lockset and necessary fixtures

No

131.90

Gates G134

Supply and install approved PVC door not exceeding l.70m2 complete with brass hook & eye and all necessary fixtures

No

102.70

G135

Supply and fix standard metal collapsible gates from approved manufacturers including all necessary fixing lugs, guide rails, rollers and gate locks. Prime and paint with 2 coats of aluminium paint

m2

127.40

G136

Supply and install single or double leaf gate consisting of 50mm diameter galvanised steel tubular framing filled in with 50 x 50mm weldmesh, 75mm diameter galvanised iron tubular gate posts with bottom end encased in 450 x 450 x 600mm concrete (1:2:4) foundation, the gates hung on 2 pairs approved hooks and ride hinges and fitted with approved locking bolt including all necessary welding and painting (Net area of leaf measured)

m2

126.10

G137

Supply and install mild steel grille gate fixed to metal gate frame, metal door frame or timber door frame (frame measured separately) with and including one primer coat(red lead primer or zinc chromate primer) and approved mortice lock(but excluding hinges) of any flower patterns and sizes not exceeding 940mm width x 2140mm height

Set

246.40

G138

Supply and install 1.6mm thick aluminium plate to metal gate including rivetting and taking out lockset and refix if necessary (new lockset measured separately)

m2

42.40

No

2.10

Windows G139

Supply and fix Safety Catch/sash lock for aluminium sliding window * Supply and install 1.2mm thick natural anodised extruded aluminium framed casement window with sheet/float glass, aluminium framing, ironmongery and cill with cement mortar infill including all necessary fixing and jointing materials and accessories *(Gl40 G14l)

G140

With 5mm thick clear sheet/float glass

m2

131.60

G141

With 5mm thick tinted sheet/float glass

m2

136.50

* Supply and install 1.2mm thick naturalanodised extruded aluminium framed top hung) window c/w sheet/float glass, aluminium framing, ironmongery and cill with cement mortar infill including all necessary fixing and jointing materials and accessories *(G142 G144) G142

With 5mm thick clear sheet/float glass

m2

146.30

G143

With 5mm thick tinted sheet/float glass

m2

151.50

G144

With 5mm thick tinted obscured / float glass

m2

172.30

SOR Page G9 Item

Description Supply and install 1.2mm thick natural anodised extruded aluminium framed adjustable louvred window c/w glass louvres, aluminium framing and sill with cement mortar infill including all necessary fixing and jointing materials and accessories *(G145 G146)

Unit

Rate ($)

G145

With 6mm thick obscure wired rough cast glass louvres

m2

155.70

G146

With 6mm thick tinted sheet/float glass

m2

145.60

Supply and install 1.2mm thick natural /anodized extrude aluminium framed 2-tracked sliding window c/w sheet/float aluminium framing, ironmongery and sill, etc including all necessary fixing, jointing materials and accessories *(Gl47 G148) G147

With 5mm thick clear sheet/float glass

m2

104.80

G148

With 5mm thick tinted sheet/float glass

m2

109.60

* Supply and install 1.2mm thick natural anodised extruded aluminium framed 3-tracked sliding window c/w sheet/float glass, aluminium framing, ironmongery and sill, etc including all necessary fixing, jointing materials and accessories *(G149 Gl50) G149

With 5mm thick clear sheet/float glass

m2

133.80

G150

With 5mm thick tinted sheet/float glass

m2

138.60

* Supply and install 1.2mm thick natural anodised aluminium framing to sliding window c/w cement mortar and all necessary fixing, jointing and accessories *(G151 G152) G151

With 2-track

m

12.50

G152

With 3-track

m

15.20

* Supply and install 1.2mm thick natural anodised extruded aluminium framed fixed panel window c/w sheet/float glass, aluminium framing including all necessary fixing, jointing and accessories *(G153 G154) G153

With 5mm thick clear sheet/float glass

m2

101.40

G154

With 5mm thick tinted sheet/float glass

m2

106.20

G155

Extra over for cilia exposed to weather (1.2mm thick natural or bronze anodised aluminium)

m

23.90

G156

Supply and install 1.2mm thick bronze anodised extruded aluminium framed casement window c/w 5mm thick tinted sheet/float glass, bronze anodised aluminium framing, ironmongery, cill with cement mortar infill all necessary fixing, jointing and accessories

m2

204.90

G157

Supply and install 1.2mm thick bronze anodised extruded aluminium framed top hung window c/w 5mm thick tinted sheet/float glass, bronze anodised aluminium framing, ironmongery, cill with cement mortar infill. all necessary fixing, jointing and accessories

m2

219.70

SOR Page G10 Item

Description * Supply and install 1.2mm thick bronze anodised extruded aluminium framed adjustable louvred windows c/w polypropylene glass holders/blade clips, bronze anodised aluminium framing, cill with cement mortar infill and all necessary fixing, jointing and accessories *(G158 G160)

Unit

Rate ($)

G158

With 6mm thick obscured wired rough cast glass louvres

m2

212.80

G159

With 6mm thick tinted sheet/float glass louvres

m2

157.60

G160

Supply and install 1.2mm thick bronze anodised extruded aluminium framed 2-tracked sliding windows c/w 5mm thick tined sheet/ float glass, bronze anodised aluminium framing, ironmongery, cill with cement mortar infill and all necessary fixing, jointing and accessories

m2

143.50

G161

Supply and install 1.2mm thick bronze anodised extruded aluminium framed 3-tracked sliding windows c/w 5mm thick tined sheet/ float glass, bronze anodised aluminium framing, ironmongery, cill with cement mortar infill and all necessary fixing, jointing and accessories

m2

165.50

Supply and install 1.2mm thick bronze anodised aluminium framing to sliding window c/w cement mortar and all necessary fixing, jointing and accessories *(Gl62 Gl64) G162

With 2-track

m

12.90

G163

With 3-track

m

16.50

G164

Supply and install bronze aluminium sliding window grilles c/w cement mortar and all necessary fixing, jointing and accessories

m2

105.80

G165

Supply and install bronze aluminium fixed window grilles c/w cement mortar and all necessary fixing, jointing and accessories

m2

98.90

G166

Supply and install stainless steel crescent lock with double locking device to aluminium sliding window

no.

6.60

G167

Supply and fix adjustable louvred window with single control side frames for 8 Nos. 150mm wide glass or metal louvres in height including rattleproof spring clips and all necessary bolts and nuts and fixed to wood, concrete or brick etc. (Louvres measured separately.)

Set

9.70

G168

Supply and fix adjustable louvred windows with dual control side frames for 8 nos. 150mm wide glass or metal louvres in height including rattleproof spring clips and all necessary bolts and nuts and fixed to wood or brickwork etc. (Louvres measured separately)

Set

12.20

G169

Supply and fix burglar proof type adjustable louvred window with single control side frames for 8 nos. 150mm wide glass or metal louvres in height including rattleproof spring clips and all necessary bolt & nuts and fixed to wood concrete or brick etc (Burglar proof bars and louvres measured separately)

Set

12.80

G170

Supply and fix burglar proof type adjustable louvred windows with dual control side frames for 8 nos. 150mm wide glass or metal louvres in height including rattleproof spring clips and all necessary bolts and nutts and fixed to wood or brickwork etc but burglar proof type (Burglar proof bars measured separately)

Set

15.10

SOR Page G11 Item G171

Description Supply and fix 10mm square mild steel burglar proof bars with rustproof finish to brackets of adjustable louvred frame.

Unit m

Rate ($) 3.20

G172

Cost adjustment for each lourve add to (or deduct from items Gl33 to Gl36)

No.

1.60

G173

Extra over for forming mullions for adjustable louvred window of any height including spacers, bolts, nuts and screws.

No.

2.80

G174

Supply and fix 1.588mm thk extruded aluminium lourved blades size not exceeding 600mm x 150mm wide in anodised finish to adjustable louvre windows including pop rivets.

No

5.90

G175

Supply and fix 2.3mm thick extruded anodised aluminium lourves not exceeding 600mm long

m2

68.80

G176

Supply and fix 150mm wide x 5mm thick in polycarbonate louvre blade

m

18.40

G177

Take down glass or metal louvres from adjustable louvre windows not exceeding 12 louvres in height and stack aside for re-use, dismantle existing damaged louvre frame from wall, timber frame and cart away debris.

Set

3.50

G178

Service and repair adjustable louvre window frame including the use of all necessary additional spare parts, easing of windows, refixing same to wall or timber frame (fixing of louvre blades measured separately)

Set

3.20

G179

Fix existing metal louvre blade to adjustable louvre window frame with poprivets.

No

0.90

G180

Fix existing glass to adjustable louvre window.

No

0.70

G181

Take down aluminium sliding windows/ doors, overhaul, ease, adjust and grease all parts including all necessary repairs and refixing same to slide properly.

m2

9.30

m2

60.00

Ceiling G182

Supply and fix 600 x 600 x 0.5mm thk Trinet or other approved perforated false ceiling complete with standard fixing accessories * Supply and fix 600 x 600 x 0.7mm thk Dampa AL-C or other approved unperforated aluminium false ceiling in the following colours complete with standard fixing accessories *(G183 G184)

G183

White

m2

72.70

G184

Other colours

m2

75.70

G185

Supply and fix Luxalon or other approved 0.5mm thick perforated metal ceiling including framing and fillets

m2

63.60

G186

Supply and install Luxalon or other approved 0.5mm thick perforated aluminium ceiling including framing and fillets

m2

77.60

G187

Supply and install 10mm thick GE Lexan thermoclear twin walled solar control venetian polycarbonate sheet in standard tint complete with DS ‘168 black anodised aluminium clamping bar system and including fixing accessories

m2

141.40

SOR Page G12 Item G188

Description Supply and install Sandwich panels (0.65mm thick enamel steel top sheet 0.8mm aluminium fluorcarbon finished bottom sheet bonded to 10mm thick aluminium honeycomb as core include aluminium capping and end cappings (powder coated finish)

Unit m2

Rate ($) 218.50

G189 to G196 NOT IN USE Mild Steel Elements * Supply, fabricate and fix mild steel such as angles, flats, plates, tees, channels, hollow sections, rivets and bolts, etc of any size including welded or bolted joints and painting one coat of lead and chromate-free primer *(G197 G201) G197

For cold formed hollow sections structural members only

Kg

2.60

G198

For hot finished hollow sections structural members only

Kg

3.00

G199

For solid section structural members only

Kg

2.50

G200

For grating only

Kg

2.30

G201

For non-structural steelworks

Kg

2.90

G202

Extra over Item G196 to G200 for hot-dipped galvanising process not less than 20 microns by approved manufacturers

Kg

0.50

G203

Supply and fix 75mm diameter Class ”C” mild steel pipe as litter bin post not exceeding lm in height from ground level with top & bottom capping welded together including excavation & embedding 300mm in concrete (1:2:4) foundation, bracket for hanging bins and 1 coat of primer and 2 coats of enamel paint

No

47.00

G204 to G208 NOT IN USE Signage G209

Supply and fix metal house number plate sizes approximately 32mm x 57mm with number of a1phabet embossed including all necessary painting

No

1.80

G210

Supply and fix plastic house number plates sizes approx. 40mm x 60mm height per digit

No

0.80

G211

Remove signage plates (any size) from walls and return to PA Office on instruction of Superintending Officer.

No

8.90

G212

Reinstall signage plates (any size) on wall with all necessary fixing accessories

No

10.70

G213

Collect old aluminium block number/address plates and refix them to wall at height to be directed by Superintending Officer including re-spraying plate with one coat of black enamel paint and yellow illuminated paint.

No

20.50

G214

Remove from site damaged carpark sign posts or bollards

No

10.10

G215 to G225 NOT IN USE

SOR Page G13 Item

Description Chequered Plate

Unit

Rate ($)

G226

Supply and fix galvanised mild steel chequered plate, cut to size, including all welding on site 2.5mm thk (net plate thickness)

m2

49.50

* Supply and fix mild steel chequered plate, cut to size including all necessary welding on site and 1 coat of bituminous paint *(G227 G228) G227

3.0mm thk (net plate thickness)

m2

40.40

G228

4.5mm thk (net plate thickness)

m2

55.00

G229

3.0mm thk (net plate thickness) for lightning conductor pit cover centre drilled with a 20mm diameter hole

No

2.80

* Supply and fix aluminium chequered plate, cut to size including all necessary bolting, etc. *(G230 G231) G230

3.0mm thk (net plate thickness)

m2

82.95

G231

4.5mm thk (net plate thickness)

m2

113.80

G232 to G258 NOT IN USE

SOR Page G14 Item G259

Description Supply and install aluminium alloy locking device to refuse chute hopper

Unit Set

Rate ($) 24.70

Mild Steel Door Frame * Mild steel door frame fixed into door openings including one coat of approved primer and all necessary fittings and hinges all as specified *(G258 G260) G260

90 x 45 x 1.6mm thick jamb to opening size 900mm width x 2190mm height

No

65.90

G261

130 x 45 x 1.6mm thick jamb to opening size 900mm width x 2190mm height

No

88.20

G262

145 x 60 x 1.6mm thick jamb to opening size 1000mm width x 2190mm height

No

96.90

Mild Steel Entrance Gate * Supply and install mild steel entrance gate to metal gate frame or metal door frame(frame measured separately) including one primer coat (primer or zinc chromate primer) aluminium finish handle and lockset and hinges, all in accordance with Board’s standard drawing *(G263 G266) G263

2 leaves plain type mild steel entrance gate

No

345.00

G264

2 leaves pattern type mild steel entrance gate

No

379.50

G265

3 leaves plain type mild steel entrance gate

No

598.00

G266

3 leaves pattern type mild steel entrance gate

No

632.50

* Galvanised steel adjustable louvre window frame with rattleproof spring clips and all necessary bolts, and fixed to timber, concrete, block/brick/solid block wall to receive 150mm wide louvres (Louvres measured separately) *(G267 G270) G267

Set of frame for single-control (standard)

m

9.70

G268

Set of frame for single-control (burglar-proof)

m

12.80

G269

Set of frame for dual-control (standard)

m

12.20

G270

Set of frame for dual-control (burglar-proof)

m

15.10

Notice Board * Supply and installation of notice boards to refer to the Term Contract for the Supply and Installation of Carpark, Traffic Sign and Estate Signboard (*G271 G274) G271

Supply & fix 3mm thick clear transparent polycarbonate cover

m2

80.00

G272

Supply only 3mm thick clear transparent polycarbonate cover

m2

45.00

G273

Supply and replace hinges

No.

4.00

G274

Supply and fix 2mm thick adhesive board backing

m2

45.00

SOR Page G15 Item G275

Description Re-apply adhesive coating onto existing backing board

Unit m2

Rate ($) 25.00

G276

Supply and fix 5mm thick clear polycarbonate or acrylic plastic sheet in panel to Notice Board including rubber glazing where necessary

m2

92.50

G277

Supply and fix 12.7mm thick soft board velvet fabric to Notice Board

m2

51.00

G278

Remove notice board and store in PA office or as directed including making good disturbed work

No.

20.20

Wrought Iron Holdfast G279

Supply and fix 25mm x 3mm x 230mm long galvanised wrought iron holdfast one end turned up and screwed to frame, other end fishtailed and slot into wall.

No

1.10

G280

Cut into existing wall and fix 25mm x 3mm x 23 0mm long galvanised wrought iron holdfast

No

4.50

No

0.80

m

16.10

m

83.50

No.

21.70

Ramset Nail G281

Supply and fix ramset nail including the use of gun and explosives. Staircase Nosing

G282

Supply and fix Stainless steel stair nosing size 50mm x 35mm x 1mm thick of grade 304 with fishtail holdfast bedded in cement mortar all as specified in detailed drawing (EM-TC-STD-BLDG-99-02) Cat ladder

G283

Supply and fix 350mm wide aluminium ladder comprising aluminium C channel and 25mm diameter aluminium tubular rungs at 305mm c/c to roof top water tank room/pump room/etc. Flushout Pipe

G284

Supply and fix additional brackets to external flush out pipes and external main risers with anchors set in brick wall or concrete wall in detailed drawing(EM-TC-STD-BLDG-99-20)(Gondola and scaffolding to be paid separately) G285 to G286 NOT IN USE

SOR Page G16 Item

Description Stainless Steel Pipe Socket

Unit

Rate ($)

G287

Supply and fix 38mm diameter x 250mm long stainless steel Grade 304 pipe socket

no.

11.20

kg

7.70

Stainless Steel Members G288

Supply and install stainless steel angles, flats, plates, tee, channels, etc. of any size fabrication including welded or bolted joints Metal Sunlouvres Supply and install 84mm wide sun-louvres including stringers in stove enamelled finish aluminium alloy mounted on supporting structure (measured separately) including nylon washers, screws and all necessary accessories *(G289 G290)

G289

Luxalon 84R-SL4

m2

124.00

G290

Luxalon 132S

m2

202.00

* Supply and install 1.2mm thick sun-louvres including extruded aluminium C-channel mullions of minimum 4mm thick galvanised steel or die-cast aluminium mullion support brackets, stainless steel bolts and nuts (Entire system to be polyester powder coated) *(G291 G293) G291

Vsun 100 Half Parafoil

m2

115.00

G292

Vsun 100 Full Parafoil

m2

190.00

G293

Vsun 700 Parafoil Insulated Sunshading

m2.

201.00

G294

Supply and install 1mm thick Unisun Cl00 blades c/w 30 or 45 degrees Dasolas panel holder clips at 100mm pitch, 20 x 30 x 3mm thick support rafters, 75 x 75 x 6mm thick support rafter brackets in stoved polyester coating and stainless steel bolts and nuts

m2.

132.00

G295

Supply and install 1mm thick Unisun Cl00 blades c/w black 60 degrees Dasolas panel holder clips at 100mm pitch, 20 x 30 x 3mm thick support rafters, 19 x 19 x 3mm thick bracing stuts, 3mm thick bracing stuts brackets/gliders, 75 x 75 x 6mm thick support rafter brackets in stoved polyester coating and stainless steel bolts and nuts

m2.

176.00

Miscellaneous G296

Labour refixing loose galvanised steel/ aluminium window flashing with masonry or ramset nails at 150mm centres and re-cutting groove in wall and patching up with cement mortar and painting to match existing

m

4.10

G297

Supply and fix approved 16mm x 16mm x 1.27mm anodised finish aluminium angles to timber louvres not exceeding 53 0mm long including 4 nos. 6mm long No.4 pan-head tapering screws

No

1.90

G298

Galvanised gauze to openings of precast concrete vent fixed with timber fillets

m2

81.40

SOR Page G17 Item G299

Description Supply and fix galvanised gauze for neat safe door fixed with fillets

Unit No

Rate ($) 8.30

G300

Supply and fix 300mm black Jappanned gallow brackets

No

3.50

G301

Fixing only loose gallow brackets including additional rawl or wood plugs

No

1.10

G302

Cut into existing wall and incorporate new 25mm x 3mm x 230mm long wrought iron holdfast and filled up hole with concrete, reinstate plaster to surface and painting to match existing

No

4.70

G303

Labour welding back broken or loose hinges to mild steel casement window leaf or frame including easing to shut properly and touching up surfaces to match existing

No

10.10

G304

Labour for removing defective steel hinge from mild steel casement windows, supply new approved hinge including all necessary rivetting, welding, easing to shut properly and touching up surfaces to match existing (labour inclusive of taking out and refixing of glass, if found necessary)

No

16.50

G305

Supply and fix metal casement windows with/without top hung, complete with frames, glazing, putting, all necessary accessories and 3 coats of enamel paint

m2

119.20

G306

Labour and material for refixing fallen mild steel clothes drying rack to ceiling with Hilti M6 or other approved

No

3.20

G307

Galvanised steel sheet as door panel

Kg

2.20

G308

Labour and material of shop premises for taking down mild steel sliding and folding door to overhaul, cease, adjust and grease all parts including all necessary repairs! welding and replacement of all damaged tube knucklers, hinges and gulders, etc and reinstall to slide properly

m2

11.10

G309

Labour and transport for dismantling and removal of casement/ sliding/ louvred window from site including frame (if any)

m2

8.50

G310

Labour and transport for dismantling and removal of metal gate from site

No

22.00

G311

Labour and transport for dismantling and removal of collapsible gate from site

m2

11.10

G3l2

Labour taking out existing metal window grilles from windows and/or balcony and remove from site

m2

5.00

G313

Labour taking out existing metal window grilles and refix in position including provision of new screws where necessary

m2

7.90

G314

Labour to weld back metal gate padlock eye

No

4.40

m2

120.00

Supplementary G315

Supply and fix approved manual operated natural anodidized aluminum roller shutter including fixtures box like enclosure & accessories, and removal of existing damaged roller shutter where applicable

H – PLASTERER AND WALL TILER S/N

Contents

SOR Page

1

Plastering

H1

2

Glazed Tiling

H1

3

Ceramic Tiling

H2

4

Mosaic Tiling

H2

5

Terrazzo

H2

6

Slate Tiling

H2

7

Granite Tiling

H2

8

Pebble Wash Tiling

H3

9

Spalling Concrete

H3

10

Hacking Works

H3

11

Patching Works

H3 – H4

12

Skim Coating

H4

13

Miscellaneous

H4

SOR Page H1 Item

Description PLASTERER AND WALL TILER (To be read in conjunction with Preambles)

Unit

Rate ($)

Plastering * Cement, sand and sandy clay (1:5:0.5) plaster in 2 coats to walls, columns, beams, soffits, etc applied WITHIN the building *(H00l H002) H001

10 - 13mm thick

m2

6.80

H002

18 - 20mm thick

m2

7.20

* Cement, sand and sandy clay (1:3:0.25) plaster in with approved plasticizer in 2 coats to walls, columns, beams, soffits etc applied from the EXTERNAL face of building *(H003 H004) H003

10 - 13mm thick

m2

8.50

H004

18 - 20mm thick

m2

9.00

H005

Extra over plastering for forming 20 x 15mm deep groove lines to wall, columns, beams etc as specified

m

2.00

H006

Extra over for waterproofing compound in accordance with the manufacturer’s instructions incorporated in the plaster works (applicable to other plasterer items)

m2

1.40

H007

White marble chipping Shanghai Plaster to walls including minimum 13mm thick cement and sand screed backing (1:3)

m2

30.80

Glazed Tiling H008

108 x 108 mm white glazed tiling to walls including coved or rounded edged tiles etc and cement and sand screed (1:3)

m2

33.00

H009

150 x 150 mm white glazed tiling to walls including coved or rounded edged tiles etc and cement and sand screed (1:3)

m2

41.70

H010

108 x 108 mm coloured glazed tiling to walls including coved or rounded ed9ed tiles etc and cement and sand screed (1:3)

m2

35.20

H011

150 x 150 mm coloured glazed tiling to walls including coved or rounded edged tiles etc and cement and sand screed (1:3)

m2

45.20

H012

100 x 200 mm white glazed tiling to walls including coved or rounded edge tiles etc and cement and sand screed (1:3)

m2

37.40

H013

100 x 200 mm or 200mm x 200mm white based floral tile to wall including coved or rounded edged tiles etc and cement and sand screed (1:3)

m2

40.00

H014

Supply and lay 100mm x 200 mm or 200mm x 200mm coloured based floral tile to wall including coved or rounded edged tiles etc and cement and sand screed (1:3)

m2

49.00

SOR Page H2 Item

Description Homogeneous/Ceramic Tiling

Unit

Rate ($)

H015

Supply and lay ceramic tiles (Heavy Duty) of any sizes minimum 8mm thick including coved or round edges of approved colour and pattern, jointed, pointed, on and including minimum 13mm thick cement and sand backing to wall (1:3)

m2

41.85

H016

Supply and lay homogeneous polished wall tiles of any sizes minimum 8mm thick including coved or round edge tiles of approved colour and pattern, jointed, pointed on and including minimum 13mm thick cement and sand backing (1:3) to wall

m2

54.90

H017

Supply and lay homogeneous unpolished wall tiles of any sizes minimum 8mm thick including coved or round edge tiles of approved colour and pattern, jointed, pointed on and including minimum 13mm thick cement and sand backing (1:3) to wall

m2

43.20

* Patch up existing damaged homogeneous unpolished/polished tiles to match existing including all necessary hacking, repointing *(H018 H020) H018

Not exceeding 0.3m2 per patch

No.

19.60

H019

Exceeding 0.3m2 and not exceeding 0.5m2 per patch

No.

32.60

H020

Exceeding 0.5m2 and not exceeding 1m2 per patch

No.

65.20

Mosaic Tiling H021

Supply and lay unglazed mosaic tiles 19mm x 19mm or 25mm x 25mm walls including coved tiles etc and cement and sand screed(1:3)

m2

39.80

H022

Supply and lay semi-glazed mosaic tiling to walls including coved tiles etc and cement and sand screed (1:3)

m2

40.60

H023

Supply and lay glazed mosaic tiling to walls including coved and rounded edge tiles etc and cement and sand screed (1:3)

m2

44.40

m2

38.40

m2

38.40

Terrazzo H024

Supply and lay 20mm thick terrazzo on brick, block or concrete walls, column surface polished including cement and sand screed (1:3) Slate Tiling

H025

Supply and lay natural slate tiles of 10-15mm thick in any approved colours and pattern jointed and pointed on and including 13mm thick cement and sand backing(1:3) to wall Granite Tiling

H026

Supply and lay l0mm-l3mm thick polished granite slabs of approved colour and pattern, jointed, pointed on and including minimum 13mm thick cement and sand backing(1:3) to wall

m2

110.80

H027

Supply and lay lOmm-l3mm thick unpolished granite slabs of approved colour and pattern, jointed, pointed on and including minimum 13mm thick cement and sand backing(1:3) to wall

m2

93.10

SOR Page H3 Item

Description Pebble Wash Finishing

Unit

Rate ($)

H028

Supply and lay 15mm thick pebble wash finish (pebble size 3mm to 5mm) to wall, columns, etc. laid in section including provision of all necessary groove lines

m2

42.00

Spalling Concrete H029

Hack 13mm ‘V’ groove along crack, apply primer and patching with epoxy mortar (inclusive of related works covered in the drawing and specification) (EM-TC-STD-ELDG-99-04)

m

10.90

H030

Repair of spalling concrete by patch repair with approved epoxy mortar (inclusive of hacking and other related works covered in the drawing and specifications)(EM-TC-STD-BLDG-99-04)

m2

144.00

H031

Repair of spalling concrete by patch repair with approved polymer modified sand-cement mortar (inclusive hacking and other related works covered in the drawing and specifications) (EM-TC-STD-BLDG-99-04)

m2

50.30

* Repair of spalling concrete by pressure grouting with non-shrink grout or other approved materials including painting and all as specified *(H032 H033) H032

For area not exceeding 0.65m2

job

155.60

H033

Extra over item H032 for area exceeding 0.65m2

m2

205.50

H034

Repair to cracks by epoxy injection method including painting to repaired surfaced as specified

m

42.00

H035

Repair to cracks by hacking “V” groove along cracks and patch with approved polyurethane sealant including painting to the repaired surface

m

16.00

Hacking Works H036

Hack out cracks in concrete walls, slabs, soffits and floors to form “V” shaped grooves approximately 25mm wide x 37mm deep, make good with cement mortar (1:3) and touch up paintwork to match existing

m

3.50

H037

Hack out cracks in concrete walls, slabs, soffits and floors to form “V” shaped grooves approximately 25mm wide x 37mm deep make good with prepacked MORTAR mixed and touch up paint work to match existing

m

3.90

H038

Hack existing plastered or concrete wall surface to form random keys, clean and wash to receive new finish

m2

2.10

H039

Hack off existing damaged plastering, glazed wall tiles/terrazzo/mosaic tiles and re-form keys on wall, tables and stools to receive new finish

m2

2.00

No

2.10

Patching Works * Patch up existing damaged wall tiles/mosaic tiles (Unglazed, semi-glazed, glazed) with new wall tiles/mosaic tiles to match with existing including all necessary hacking, re-pointing (rates also applicable to tables, stools and play equipment) *(H040 H041) H040

Not exceeding 0.02 metre square per patch

SOR Page H4 Item H041

Description Exceeding 0.02 and not exceeding 0.1 metre square per patch

Unit No

Rate ($) 5.70

H042

Patch existing holes not exceeding 150mm square sectional area in walls, ceilings etc with cement mortar or putty and touching up painting to match existiig

No

0.80

Skim Coating Skim coat of approved prepacked skimming material applied from within the building *(H043 H044) H043

To walls

m2

3.90

H044

To ceilings

m2

4.20

Skim coat of approved prepacked skimming material applied from the external face of the building *(H045 H046) H045

To walls

m2

4.60

H046

To sides soffit of beams and slabs

m2

5.10

H047

Prepare and apply skim coating to external rc surfaces in two coats to a maximum total thickness of 6mm using approved prepacked skimming materials according to manufacturer’ s instructions 18mm thick plastering with approved prepacked MORTAR mixed to RC surface, brickwalls and block walls, etc as specified *(H048 H049)

m2

8.00

H048

Within the building

m2

9.30

H049

From external face of the Building

m2

10.90

Miscellaneous H050

Supply labour for laying tiles (any grades, sizes, colours and patterns) including 13mm cement and sand screed (1:3) and pointing, to wall

m2

20.00

H051

Pull out nails, hooks etc from walls and ceilings and patch up hole including touching up painting to match existing

No

0.50

H052

Re-pointing joints of existing wall tiling in white cement including cleaning surface on completion

m2

2.40

H053

Prepare and wash with high water jet and hypochloride acid or approved detergent to remove all surface contaminants on all surfaces

m2

3.00

H054

Spatterdash of cement slurry on existing surface to form key

m2

0.60

H055

Rough cast plastering to walls

m2

12.30

I – GLAZIER S/N

Contents

SOR Page

1

Glass Panes

I1

2

Glass Lourves

I1

SOR Page I1 Item

Description GLAZIER (To be read in conjunction with Preambles)

Unit

Rate ($)

Glass Panes * Ordinary quality clear sheet/obscured timber/steel/aluminium/windows /doors/vents/ partitions *(I00l 1013)

glass

etc.

to

I001

4mm thick clear sheet glass

m2

32.80

I002

6mm thick clear sheet glass

m2

37.40

I003

5mm thick obscured glass

m2

43.90

I004

5mm thick tinted float glass in panes

m2

37.10

I005

6mm thick tinted float glass in panes

m2

39.10

I006

6mm thick clear tempered float toughened glass

m2

100.40

I007

8mm thick clear tempered float toughened glass

m2

131.60

I008

10mm thick clear tempered float toughened glass

m2

152.10

I009

12mm thick clear tempered float toughened glass

m2

185.50

I010

6mm thick tinted tempered float toughened glass

m2

106.10

I0ll

8mm thick tinted tempered float toughened glass

m2

144.90

I012

10mm thick tinted tempered float toughened glass

m2

166.40

I013

12mm thick tinted tempered float toughened glass

m2

211.10

Glass Louvres * The following in louvres (varying from 100 to 200mm wide) ordinary quality clear float/obscured glass with ground and polished edges fixed to metal or timber frames *(1014 1018) I014

5mm thick

m2

36.10

I015

6mm thick

m2

40.70

I016

5mm thick obscured glass

m2

43.90

I017

6mm thick obscured wiredg1ass panes, or louvres in replacement

m2

47.50

I018

Provide and apply putty for securing glass panes to metal windows including removal of damaged putty

m

0.70

J – PAINTER S/N

Contents

SOR Page

1

Synthetic Enamel Paint

J1 – J2

2

Aluminium Paint

J3

3

Acrylic Emulsion Paint

J3

4

Water Based Algae Resistant Emulsion Paint

J3

5

Pesticide Paint

J4

6

Bituminous Paint

J4

7

Spray Painting to Lift Car

J4

8

Varnish to Woodwork

J4

9

Spray Paint

J4

10

Wood Preservative

J5

11

Game Court Lines

J5

12

Miscellaneous

J5 – J6

SOR Page J1 Item

Description PAINTER (To be read in conjunction with Preambles)

Unit

Rate ($)

Synthetic Enamel Paint * Painting plain surfaces of woodwork and metal work etc, including sand papering as specified *(J001 J002) J001

One finishing coat

m2

2.00

J002

One undercoat and one finishing coat

m2

3.10

* Painting steel casement windows, metal grilles, etc including sand papering as specified. (Measured flat overall, Rate inclusive of painting to both faces) *(J003 J004) J003

One finishing coat

m2

2.80

J004

One undercoat and one finishing coat

m2

4.90

* Painting timber louvred surfaces including sand papering as specified. (Measured as flat both sides over area of casement. Rate inclusive of painting to both faces) *(J005 J006) J005

One finishing coat

m2

5.20

J006

One undercoat and one finishing coat

m2

10.20

* Painting pipes, railing, etc not exceeding 75mm diameter (round section) or not exceeding 250mm girth (square or rectangular section) or galvanised chain to swing including sand papering as specified *(J007 J008) J007

One finishing coat

m

1.00

J008

One undercoat and one finishing coat

m

1.70

* Painting pipes, railing, etc exceeding 75mm diameter but not exceeding 150mm diameter (round section) or exceeding 250mm but not exceeding 450mm girth (square or rectangular section) including sand papering as specified *(J009 J010) J009

One finishing coat

m

1.50

J011

One undercoat and one finishing coat

m

2.60

* Painting to UPVC pipe not exceeding 75mm diameter including sand papering using synthetic enamel paint *(J011 J012) J012

One finishing coat

m

0.90

J013

One undercoat and one finishing coat

m

1.50

* Painting to UPVC pipe exceeding 75mm diameter but not exceeding 150mm diameter including sand papering using synthetic enamel paint *(J013 J014) J014

One finishing coat

m

1.40

J010

One undercoat and one finishing coat

m

2.50

SOR Page J2 Item

Description * Painting to UPVC pipe not exceeding 75mm diameter including sand papering using synthetic enamel paint *(J011 J012)

Unit

Rate ($)

J011

One finishing coat

m

0.90

J012

One undercoat and one finishing coat

m

1.50

* Painting to UPVC pipe exceeding 75mm diameter but not exceeding 150mm diameter including sand papering using synthetic enamel paint *(J013 J014) J013

One finishing coat

m

1.40

J014

One undercoat and one finishing coat

m

2.50

* Painting fillets, glazing bars, etc not exceeding 150mm girth *(J015 J016) J015

One finishing coat

m

0.90

J016

One undercoat and one finishing coat

m

1.70

* Painting metal lamp guard and fluorescent tube casing in ONE UNDERCOAT and ONE FINISHING COAT *(J017 J018) J017

600mm long

No

2.00

J018

1.2m long

No

2.80

J019

Cleaning and painting to fan blade and cage in one undercoat and one finishing coat

No

10.70

J020

Painting metal surface with one coat approved lead and chromate free primer

m2

2.40

J020

Painting non-ferrous metal surface with one coat of approved etching primer

m2

2.25

* Painting to 50mm diameter Bird Hanging Pole exceeding 5 metre but not exceeding 6 metre height *(J022 J023) J022

One finishing coat

No

7.00

J023

One undercoat and one finishing coat

No

11.00

J024

Painting one undercoat and one finishing coat of synthetic paint to external surface of timber door including door frames to door openings not exceeding 2.5m2

No.

10.90

J025

Painting one finishing coat of synthetic enamel paint to both faces of m.s. gate not exceeding 2.5m2

No.

7.00

SOR Page J3 Item

Description Aluminium Paint * Painting metal adjustable louvred window blades (Measured as flat both sides over area of adjustable louvred window. Rate inclusive of painting to both faces) *(J025 J027)

Unit

Rate ($)

J026

One coat

m2

2.30

J027

Two coats

m2

4.20

m2

5.90

m2

9.30

m2

2.60

* Painting metal collapsible gates, iron folding gate etc. (Measured flat overall. Rate inclusive of painting to both faces) *(J028 J030) J028

One Coat

J029

Two coats

J030

On refuse chamber door in 2 coats * To pipes, railing, etc not exceeding 75mm diameter or galvanised chain to swing including sand papering as specified *(J031 3032)

J031

One finishing coat

m

0.90

J032

One undercoat and one finishing coat

m

1.60

* To pipes, railing, etc exceeding 75mm diameter but not exceeding 150mm diameter including sand papering as specified *(J033 J034) J033

One finishing coat

m

1.50

J034

One undercoat and one finishing coat

m

2.60

Acrylic Emulsion Paint * Apply approved acrylic emulsion paint (with maximum 10% dilution) to surfaces of walls, ceilings, columns, etc including preparing surfaces as specified *(J035 J037) J035

One coat

m2

1.00

J036

Two coats (with maximum 10% dilution for first coat, and without water dilution on second coat)

m2

1.90

J037

Three coats (with maximum 10% dilution for first coat, and without water dilution on second and third coats)

m2

2.60

Water Eased Algae Resistant Emulsion Paint * Apply approved water based algae resistant emulsion paint to surfaces of walls, ceiling, columns, etc including preparing surfaces as specified *(J038 J040) J038

One coat

m2

1.30

J039

Two coats (with maximum 10% dilution for first coat, and without water dilution on second coat)

m2

2.30

J040

Three coats (with maximum 10% dilution for first coat and without dilution to second and third coats)

m2

3.30

SOR Page J4 Item

Description Pesticide Paint

Unit

Rate ($)

* Apply ENV approved pesticide paint (with maximum 5% dilution) to surface of walls, ceiling, column etc. including preparing surfaces as specified *(J041 J042) J041

One coat (without dilution)

m2

1.70

J042

Two coats (with maximum 5% dilution for first coat and without water dilution on second coat

m2

3.10

Bituminous Paint J043

Prepare and apply 1 coat of non-toxic bituminous paint on surface of mild steel plate & rolled steel joists

m2

1.90

J044

Mild steel drain cover gratings (measured separately) dipped in Bitutect No. 1 or approved bituminous paint (rate inclusive of both faces)

m2

2.50

Spray Painting to Lift Car * Prepare and spray one finishing coat of approved, automobile paint *(J045 J047) J045

Lift car ceiling

No

17.70

J046

Lift car frames and header

No

12.20

J047

Lift car door (one side only)

No

20.90

Varnish To Woodwork J048

Stain, prepare and apply 2 coats shellac varnish on new or existing woodwork

m2

6.30

J049

Prepare and apply two coats of approved stain and wax polish or polyurethane varnish on general surfaces of woodwork

m2

6.10

Spray Paint J050

Spray painting on plain surface of metal work in one finishing coat of synthetic enamel paint

m2

2.00

J051

Spray paint lettering (300mm in height) to CRC roller shutter surface “No Parking Fine Max. $1,000/-”.

No

48.30

* Spray painting of numerals/alphabets to roller shutter of bin chute centre to warn illegal parking of vehicle. *(J052 J054) J052

Not exceeding 300mm high

No

2.10

J053

Exceeding 300mth but not exceeding 600mm high

No

3.70

J054

Exceeding 600mm but not exceeding 1000mm high

No

5.30

J055

Spray painting of minimum 75mm high numerals and letterings to bin chute chamber door, storey indicator, pipes service duct doors, dry riser inlet panel etc (‘No” means per pipe/door/dry riser/inlet panel/indicator)

No

1.50

SOR Page J5 Item

Description Wood Preservative

Unit

Rate ($)

* Apply approved wood preservative *(J056 J057) J056

One Coat

m2

1.70

J057

Two Coats

m2

3.00

m

1.40

m

1.80

m

3.20

Game Court Lines * Painting of Games Court lines with heavy duty Thermal Plastic Polyurethane paint or approved epoxy paint *(J058 J060) J058

38mm wide

J059

50mm wide

J060

100mm wide Miscellaneous

J061

Brush, wash down and apply one coat water-based sealant on concrete or plastered surfaces

m2

1.00

J062

Paint existing column edge angle bar at carpark using illuminated/ fluorescent paint

m

1.70

J063

Apply approved polyurethane paint of 2 pack system

m2

6.70

J064

Skilled labour to restore mural inclusive of paint etc

m2

5.60

J065

Paint existing table tennis top and exposed edges with 2 coats approved paint, mark out new lines and 2 coats of enamel paint to steel hollow section frames

No

45.00

* Painting to pipe at roof top not exceeding 150mm diameter including sand papering using approved ceramic insulation coating *(J066 J067) J066

One finishing coat

m

3.70

J067

One undercoat and one finishing coat

m

6.50

m

6.00

m

10.20

m2

3.60

* Painting to pipe at roof top exceeding 150mm diameter but not exceeding 300mm diameter including sand papering using approved ceramic insulation coating *(J068 J069) J068

One finishing coat

J069

One undercoat and one finishing coat

J070

Apply one coat of rust inhabitor primer to metal surface to receive new coating

SOR Page J6 Item

Description Apply approved ceramic insulation coating to surface of metal roof, etc. including sand papering *(J071 J072)

Unit

Rate ($)

J071

One finishing coat

m2

5.00

J072

One undercoat and one finishing coat

m2

8.50

J073

Skilled labour to sand wood surfaces to a perfect even surface and clean surface to receive new finish including all necessary equipment, tools and accessories

m2

1.60

Prepare, align, set out and apply manually quick drying chlorinated rubber based paint on concrete surface (any colour) *(J074 J075) J074

One coat

m2

1.70

J075

Two coats

m2

2.90

Clean and apply wax polish to general surface of marble, terrazzo, mosaic or other finish and polish manually or with machine including all necessary equipment, tools and accessories *(J076 J077) J076

One coat

m2

2.30

J077

Two coats

m2

4.00

J078

Prepare, grind manually or with machine complete with 2 process of wax polish on general surfaces of marble, terrazzo or other finish including all necessary machineries/tools and accessories

m2

12.60

K – NOT IN USE

L – DAYWORK S/N

Contents

SOR Page

1

Labour

L1

2

Plant

L1 – L2

3

Mechanical Suspended Cradles

L2

4

Tubular Steel Stagings

L2

5

Timber Scaffold

L3

6

Metal Scaffold

L3

7

Mobile Lighting Platform

L3

8

Self-Propelled Aerial Platform / Boomlift

L3 – L4

9

Testing of Materials

L4 – L6

10

Labour for Cleaning Up

L6

SOR Page L1 Item

Description DAYWORK Provide labour and plant described in the following items as may be ordered in writing by the Superintending Officer

Unit

Rate ($)

Labour L001

Labourer

Hr

5.00

L002

Concretor

Hr

7.20

L003

Steel Bender and Fixer

Hr

6.80

L004

Steel Worker

Hr

6.70

L005

Welder

Hr

7.10

L006

Carpenter

Hr

6.20

L007

Pavior

Hr

6.90

L008

Tiler

Hr

7.90

L009

Plasterer

Hr

7.20

L010

Mason/Brick/Block Layer

Hr

7.10

L011

Painter

Hr

7.10

L012

Joiner

Hr

7.80

L013

Ironmonger

Hr

7.70

L014

Lorry Driver

Hr

7.40

L015

Roofer

Hr

7.70

L016

Watchman

Hr

3.90

L017

Mechanic

Hr

8.40

L018

Glazier

Hr

7.20

L019

Drainlayer

Hr

7.00

L020

Plumber

Hr

6.70

L021

Scaffolder

Hr

6.20

L022

Wireman

Hr

7.20

L023

Plant Motor Lorry (Pick-up) not more than 2.50 tonne including fuel and driver

Hr

14.00

L024

Motor Lorry 3 tonne size including fuel and driver

Hr

19.90

L025

Motor Lorry 7 tonne size including fuel and driver

Hr

21.90

L026

Motor crane including fuel and driver (3 tonne lifting capacity)

Hr

25.10

SOR Page L2 Item L027

Description Air compressor with air delivery capacity not less than 4.5 Cu m per minute including pneumatic tools, fuel and tool sharpening(no labour)

Unit Hr

Rate ($) 16.00

L028

Wheel or crawler shovel or excavator loader with back hoe bucket not exceeding 0.4 cu m or 1.30 cu m loader bucket capacity including fuel and driver e.g. Kobe 904, JCB

Hr

47.40

L029

Power loader or rubber-tyre wheels 1.20 cu m bucket capacity (Flywheel horse power 60 KW range) including fuel and driver

Hr

40.90

L030

Traxcavator 1.00 Cu m capacity including fuel and driver eg. CAT 933

Hr

49.70

L031

Power driven pump - 50mm size including fuel

Hr

8.90

L032

Power driver pump - 75mm size including fuel

Hr

14.50

L033

Diesel powered field welding machine with minimum capacity 300 amp

Hr

8.80

L034

Connect mixer 200/140 litres capacity including fuel

Hr

9.40

L035

Concrete mixer 300/200 litres capacity including fuel

Hr

10.60

Mechanical Suspended Cradles L036

Submit drawings and roof plans by Professional Engineer to the relevant Authorities for approval (building having similar roof plans/design shall be included in this rate and shall NOT be paid separately under one operation)

Block

402.50

L037

Carry out testing of mechanical suspended cradles by (M & E) Professional Engineer and obtain approval the relevant Authorities

Test

230.00

L038

Supply and install mechanical suspended cradle not exceeding 5 metres length to the roof including PE endorsement certifying the proper installation of suspended cradle according to the PE’s design calculations, drawings and roof plans (hiring charges and shifting shall be paid separately)

Unit

575.00

L039

Hiring charge of approved mechanical suspended cradle not exceeding 5m length including all accessories and safety precautions

Day

60.00

L040

Labour for shifting approved mechanical suspended cradle within the same block by one gang

Shift

30.00

L041

Labour for shifting approved mechanical suspended cradle within the same block by one gang for more than one shift per day (Per Job means Multiple Shift per Day)

Per Job

50.00

Tubular Steel Staging * Erect of tubular steel staging including platform board, swivel castors or base plate etc and taking down after use *(L042 L043) L042

Per stage of exceeding 6 metres and not exceeding 8 metres high.

No

75.50

L043

Per stage of exceeding 8 metres and not exceeding 10 metres high.

No

90.00

SOR Page L3 Item

Description Timber Scaffold

Unit

Rate ($)

L044

Erect double layer timber scaffolding including taking down after use (height of scaffolding not exceeding 15m high. A minimum of 5 metre width shall be paid)

m2

4.60

Metal Scaffold L045

Erect metal scaffolding not exceeding 15 metre height including taking down after use

m2

11.50

L046

Erect metal scaffolding exceeding 15 metre height but not exceeding 35 metre height including taking down after use

m2

12.70

Hiring Charge of Mobile Lifting Platform L047

Submit drawings and design calculations by Professional Engineer to the relevant Authorities for approval to install mobile lifting platform (building having similar plans/designs shall be included in this rate and shall NOT be paid separately under one operation)

Blk

402.50

L048

Submit the certification of supervision by Professional Engineer certifying the proper installation of mobile lifting platform according to the Professional Engineer’s design calculations and drawings

Test

207.00

L049

Carry out test of mobile lifting platform by approved person (PE Structural Engineer and PE Mechanical Engineer) from the relevant authorities

Test

345.00

L050

Supply and install Single Mast Mobile Lifting platform not exceeding 11 metres length including subsequent removal off site upon completion of work, making good to affected area (hiring changes shall be paid separately)

Unit

920.00

* Hiring charge of Single Mast Mobile Lifting Platform including allaccessories and safety precautions (subject to a minimum of one week rental. If duration exceeds one week, the remaining will be paid by per day basis) *(L051 L052) L051

For one month

month

1380.00

L052

For one day

day

53.10

L053

Labour for shifting approved Drive Unit Mast Platform including supervision by Professional Engineer

Shift

690.00

no.

276.00

Hiring of Self-propelled Aerial Platform/Boomlift * Note The Hiring charge for Self-propelled Aerial Platform/Boomlift (item L053 to L062) to be paid will be based on the minimum amount calculated using daily, weekly and monthly rates L054

Transportation and installation of self-propelled Aerial Platform/Boom lift on site and subsequent removal off site upon completion of work including make good to affected area (Hiring charge shall be paid separately) * Hiring of Self-propelled Aerial Platform/ Boomlift of maximum platform height of 12m

SOR Page L4 Item L055

Description For daily

Unit day

Rate ($) 294.00

L056

For weekly

week

1196.00

L057

For monthly

month

2944.00

* Hiring of Self-propelled Aerial Platform/ Boomlift of maximum platform height of 18m L058

For daily

day

386.40

L059

For weekly

week

1518.00

L060

For monthly

month

3680.00

* Hiring of Self-propelled Aerial Platform/ Boomlift of maximum platform height of 25m L061

For daily

day

598.00

L062

For weekly

week

2392.00

L063

For monthly

month

5520.00

Testing of Materials L064

Pull out test for plaster (Per point for external)

point

92.00

L065

Pull out test for plaster (Per point for internal)

point

92.00

L066

Pull out test for brick tile (Per point for 200 x 200mm)

point

115.00

L067

Polymer Modified Sand Cement Mortar : Compressive Strength Test (Test Method ASTM C109 1992)

age

345.00

L068

Polymer Modified Sand Cement Mortar : Setting Time Test (Test Method : BS4550 : Part 3 Section 3.6 : 1987)

test

345.00

L069

Polymer Modified Sand Cement Mortar Shrinkage Test (Test Method : ASTM C531 : 1995)

test

690.00

L070

Polymer Modified Sand Cement Mortar : Bond Strength Test (Test Method ASTM C190 1985)

age

517.50

L071

Polymer Modified Sand Cement Mortar : Polymer Solid Content Test(Test Method : Chemical Analysis)

test

920.00

L072

Polymer Modified Sand Cement Mortar : Air Permeability Test(Test Method : Modified Figg Air Test)

test

690.00

L073

Non-shrink Pressure Grout Flow Consistency Test (Test Method ASTM C939 - 93)

test

115.00

L074

Non-shrink Pressure Grout Expansion/ Shrinking Test (Test Method ASTM C940 - 89)

test

345.00

L075

Non-shrink Pressure Grout Bleeding Test (Test Method ASTM C940 - 89)

test

172.50

SOR Page L5 Item L076

Description Non-shrink Pressure Grout Setting Time Test (Test Method ASTM C953 87)

Unit test

Rate ($) 172.50

L077

Non-shrink Pressure Grout Compressive Strength Test [Test Method ASTM C942 - 88 (1991)] *Supply labour and materials for cleaning up and washing with detergent, sweep dry and damp mop the following: *(L075 L084)

test

230.00

L078

1-Room Flat

Job

36.90

L079

2-Room Flat

Job

45.60

L080

3-Room Flat

Job

53.70

L081

4-Room Flat

Job

63.60

L082

5-Room Flat

Job

73.70

L083

Executive Flat

Job

83.60

L084

Market/Hawker Stall

Job

15.40

*Supply labour and materials for cleaning up and washing first with detergent, sweep dry, then damp mop with Clorox or other approved consecutively for three times, open all windows and main entrance door to air the flat for one hour including spraying of deodorizer to the whole flat *(L085 L089) L085

1-Room Flat

Job

38.10

L086

2-Room Flat

Job

50.40

L087

3-Room Flat

Job

62.50

L088

4-Room Flat

Job

75.40

L089

5-Room Flat

Job

88.70

L090

Labour for removal of unwanted furniture, fitting, fixings, etc c/o metal, plastic, wood, glass and other compressed materials of total quantities requiring only one labour to the skip tank/dustbin compound and designated area within site, fiot exceeding 0.5 cu m (measured in original overall dimensions)

Item

4.00

L091

Labour for removal of unwanted furniture, fitting, fixings, etc c/c metal, plastic, wood, glass and other compressed materials of total quantities requiring two labourers to the skip tank/dustbin compound and designated area within site, not exceeding 0.5 cu m but not exceeding 2.O cu m (measured in original overall dimension)

Item

8.10

L092

Labour for removal of unwanted furniture, fitting, fixings, etc c/o metal, plastic, wood, glass and other compressed materials of total quantities requiring two labourers to the skip tank/dustbin compound and designated area exceeding 2.O cu m (measured in original overall dimension)

Item

12.10

SOR Page L6 Item

Description *Supply labour and transport for removal of debris from the following to dumping ground * (L093 L098)

Unit

Rate ($)

L093

1-Room Flat

Job

41.90

L094

2-Room Flat

Job

45.90

L095

3-Room Flat

Job

49.90

L096

4-Room Flat

Job

53.90

L097

5-Room Flat

Job

58.00

L098

Market/Hawker Stall

Job

41.90

L099

Supply of skip tank for unwanted articles and debris (not exceeding 20m2) including removal and cast away to approved dumping ground (Rate inclusive of ENV fees, etc.)

No

345.00

M – NOT IN USE

N – CEILING LEAK REPAIRS S/N

Contents

SOR Page

1

Repair of Leaks

N1

2

Floor Finishings

N1 – N2

3

Waterproofing

N2

SOR Page N1 Item

Description CEILING LEAK REPAIRS (to be read in conjunction with preambles)

Unit

Rate ($)

Repair of Leaks N001

Hack away existing plasterwork to expose building components for visual inspection inclusive of reinstatement works to match existing (for areas not exceeding 0.20 m2 per patch)

Patch

15.00

N002

Repair cracks by epoxy injection

m

47.80

N003

Expose the concrete surface, grind, dampen and apply crystalline waterproofing material as specified

m2

15.00

N004

Repair water seepage through porous concrete by injecting approved water reactive polyurethane based chemical grout as specified

m

56.00

* Remove existing screed and addition of new waterproofing sand-cement screed minimum 20mm thick of 1 part cement to 2 parts sand by weight with approved waterproofing additive and laid as specified *(N005 N006) N005

For area not exceeding 3.5m2 (per unit)

Job

122.50

N006

For area exceeding 3.5m2 (per unit)

m2

31.50

N007

Repair to water leakage through floor slab around sanitary piping/floor trap using approved water plug or non-shrink grout inclusive of the use of bonding agent and make good the repaired area with waterproofed mortar and floor tiles to match with the existing floor tiles and bedding around pipe and other related works as specified

Point

72.00

N008

Rectification of sanitary opening on rc slab to details as specified and shown in drawings attached (per unit) (tiling work measured separately)

Job

125.00

N009

Add to last item for each additional opening in the same unit

Job

50.00

N010

Extra over rectification of sanitary opening for ceramic floor tiles finish

m2

62.00

N011

Extra over rectification of sanitary opening for mosaic floor tiles finish

m2

51.50

Floor Finishes * Removal of existing screed and addition of new non-shrink grout or other approved materials screed minimum 20mm thick, and laid as specified *(N012 N013) N012

For area not exceeding 3.5m2 (per unit)

Job

191.00

N013

For area exceeding 3.5m2 (per unit)

m2

52.00

* Supply and lay homogeneous ceramic floor tiles on cement and sand (1:2) screed with approved waterproofing additive by weight (a minimum thickness of 13mm at the lowest end of the fall) to match with the surrounding inclusive of bedding screed and other related works as specified *(N0l4 N015) N014

For area not exceeding 3.5m2 (per unit)

Job

220.00

N015

For area exceeding 3.5m2 (per unit)

m2

60.00

SOR Page N2 Item

Description * Supply and lay mosaic tiles on waterproofing cement and sand (1:2) screed with approved waterproofing additive by weight (a minimum thickness of 13mm at the lowest end of the fall) to match with the surrounding and inclusive bedding screed and other related works as specified *(N0l6 N017)

Unit

Rate ($)

N016

For area not exceeding 3.5m2 (per unit)

Job

189.00

N017

For area exceeding 3.5m2 (per unit)

m2

52.00

N018

Extra over for floor finishes repair to water leakage through floor slab around sanitary piping/floor slab or other porous area using approved water plug or non-shrink grout inclusive of the use of bonding agent

Point

35.00

Waterproofing * (N019 N021) N019

Application of liquid-applied elastomeric waterproofing membrane inclusive of preparing the concrete floor surface, priming and curing according to manufacturer’ s instructions

m2

11.20

N020

Application of crystalline or cementitious waterproofing compound onto the concrete surface inclusive of preparing the concrete surface priming and curing according to manufacturer’s instructions

m2

10.30

N021

Application of liquid-applied flexible cementitious waterproofing membrane inclusive of preparing the concrete surface priming and curing according to manufacturer’ s instruction

m2

13.20

P – NOT IN USE

SOR Page Q1 SCHEDULE OF RATES FOR WINDOW CHECKING, REPAIR AND REPLACEMENT/ INSTALLATION OF WINDOWS Item

Description

Unit

Rate ($)

Per flat

40.00

* Supply tools and skilled workers to check all sliding, top and side hung casement windows in unit building for compliance with PA’s requirements and give inspection checklist to owner including transportation cost Q001

All flat types * Add to Items Q001 for supply and fix in replacement the following window spare parts including taking down window panel if necessary and refixing in position and making good work disturbed *(Q005 Q009)

Q002

Fasteners

No.

2.00

Q003

Friction stay

No.

10.00

Q004

Corner bracket

No.

5.00

Q005

Safety device (safety stopper at top rail)

No.

3.00

Q006

Safety device (aluminium angle strip)

m

9.00

Q007

All rollers on sliding window

No.

3.00

Q008

5mm thick green grey/grey tinted float glass in panes

m2

35.00

Q009

6mm thick obscured wired rough cast glass louvres

m2

45.00

* Supply and fix in replacement bronze anodised extruded aluminium framed window complete with 5mm thick green grey/grey tinted float glass and ironmongery and all necessary fixing and jointing materials and accessories as specified (measurement based on size of opening) *(Q010 Q014) Q010

Top hung casement window

m2

180.00

Q011

Side hung casement window

m2

100.00

Q012

Top and side hung casement window

m2

125.00

Q013

2-track sliding window with top hung casement

m2

110.00

Q014

3-track sliding window with top hung casement

m2

120.00

Q015

Supply and fix in replacement bronze anodised extruded aluminium framed adjustable louvred vents complete with aluminium “U” clips/holders, 6mm thick obscured wired rough cast glass louvres and all necessary fixing and jointing materials and accessories as specified (measurement based on size of opening)

m2

200.00

TERM CONTRACT FOR BUILDING WORKS PROPOSED SUPPLEMENTARY SCHEDULE OF RATES ALUMINIUM ROLLER SHUTTERS Supply and fix approved manual operated natural anodized aluminium roller shutter including necessary fixtures, box-like enclosure & accessories, and removal of existing dmaged roller shutter where applicable

UNIT PRICE $120/- per m2 (refer to Annex A)

SAFETY REQUIREMENTS FOR INSTALLATION & REPAIR OF WINDOWS AND CHECKLIST FOR SAFETY OF EXISTING WINDOWS

SCHEDULE OF RATES (SUPPLY & INSTALLATION OF SIGNBOARDS)

SOR Page 1 SUPPLEMENTARY SCHEDULE OF RATES Item

Descriptions of Works

Unit

Rate

*Supply and install perspex sheet to walls, columns and doors of toilets as shown in drawing no.: EM-TC-STD-SIGN(E)-1002-04; Overall size: 0.2m X 0.3m X 3mm thick *(374-375) 374

Male sign

No.

25.00

375

Female sign

No.

25.00

*Supply and install Perspex sheet to walls, columns and doors of toilets as shown in drawing no.:EM-TC-STD-SIGN(E)-1002-04; Overall size 0.15m X 0.15m X 3m thick *(376-377) 376

Male sign

No.

15.00

377

Female sign

No.

15.00

378

Supply and install 3mm thick Perspex sheet with any graphics or wordings ro walls and columns; any sign

No.

30.00

379

Supply and install stainless steel sign; Overall size 0.3m X 0.44m X 0.08m thick Arrow sign as shown in drawing no.: EM-TC-STD-SIGN(E)-1002-04 including all approved mounting accessories

No.

350.00

No.

50.00

No.

120.00

*Supply and install acrylic sheet with reversed silkscreen printing (any background colour) c/w 4 nos. stainless steel counter-sunk screws and plastic plus (letterings to be paid separately * (380-381) 2mm thick 380 381

4mm thick Illuminated block number sign from wall

SOR Preamble SCHEDULE OF RATES - SANITARY

1.

The rates contained herein include the use of materials, labour, maintenance, supply of fuel and all idling time of vehicles, opening up, taking down, cutting and refixing preparation for washing turning on and off of water supply, tightening bolts and nuts (where necessary) provision of standby plumbers, ladders and torchlights, other tools / equipment and removal of all debris, empty tins and other unwanted materials from the roofs, all as specified, including making good all leaking tank panels with approved sealants where necessary), fitting, fixing in position, all cutting and waste, return of packings, establishment charges, overheads, profit and all forms of claim of loss and expense and making good all work disturbed, unless otherwise stated.

2.

The rates of painting of water tanks unless otherwise stated included the preparation of surfaces as per manufacturer’s recommendation and the Employer’s instructions. No dilutions of coating materials are allowed unless recommended by the manufacturer and the Employer. The application of coating materials shall comply strictly to the manufacturer’s recommendations and the Employer’s instructions.

3. The rates are applicable for work carried out in the Market/Hawker Centres, eating houses and other premises as directed by the Superintending Officer. 4. The cost of hacking, removal and disposal, and the making good of all affected works shall be deemed to be included in the Schedule of Rates unless otherwise stated. All schedules of Rates shall be applicable for new and replacement work. 5. Unless otherwise stated, all works shall be measured nett as fixed in its place. Pay length of pipes shall be measured on exposed length. 6. All pipes are described by their normal size except copper, stainless steel, and upvc pipes which are meant to be their normal size. 7. The Employer reserves the right the direct the Contractor to execute any of the undermentioned items of works which he considers necessary. 8. All rates in the Schedule shall include all necessary materials and waste, plant, staging and scaffolding (only applicable up to 6m high, any height above 6 metres shall be paid separately, measuring from ground level, i.e. from the base for which scaffolding rests unless specified otherwise.

SCHEDULE OF RATES

CONTENTS (A) EXCAVATION WORKS (B) CONCREROR WORKS (C) BRC (D) STEEL AND IRON WORKS (E) MANHOLE (F) STONEWARE PIPES (IN REPLACEMENT) (G) CAST IRON PIPES AND FITTINGS (H) DUCTILE IRON PIPES AND FITTINGS (I) GALVANISED STEEL PIPES AND FITTINGS (J) UPVC PIPES AND FITTINGS (K) STAINLESS STEEL PIPES, COPPER PIPES AND FITTINGS (L) SANITARY FITTINGS AND ACESSORISES (M) BIB TAPS/ STOP COCKS/ VALVES FOR SANITARY WORKS (N) TRAP AND GRATING (IN REPLACEMENT) (O) SUPPLY AND INSTALLATION / REPAIRS AND REINSTATEMENT WORKS FOR SANITARY (P) CLEANING AND DESILTING WITH ELECTRO-MECHANICAL EQUIPMENT (Q) WATER TANK REPAIRS, CLEANING & PAINTING WORK (R) MATERIALS SUPPLY (S) DAY WORKS (T) MISCELLANEOUS

SOR Page 1 Item

Description of Works (A) EXCAVATION WORKS

Unit

Rate ($)

A001

Excavate trenches/pits not exceeding 2.0m deep for drains/ manholes, part return, fill in and ram, remainder cart away, deposit, spread and level as directed including planking and strutting.

m3

6.80

A002

Excavate trenches/pits not exceeding 2.0m and not exceeding 4.0m deep for drains/ manholes, part return, fill in and ram, remainder cart away, deposit, spread and level as directed including planking and strutting.

m3

17.00

A003

Excavate trenches/pits not exceeding 4.0m and not exceeding 6.0m deep for drains/ manholes, part return, fill in and ram, remainder cart away, deposit, spread and level as directed including planking and strutting.

m3

22.70

8

SOR Page 2 Item

Description of Works (B) CONCRETE WORKS

Unit

Rate ($)

B001

Breaking up concrete

m3

50.80

B002

Concrete Grade 20 in small quantities not exceeding 0.15 cubic metre including trowel smooth and formwork

m3

224.80

B003

Concrete Grade 20 bed 400mm wide X 100mm thick under 100mm diameter drain pipes including haunching up sides of pipes to not less than half diameter of the pipes and necessary formwork (Drain pipes measured separately)

m

11.90

B004

Concrete Grade 20 bed 450mm wide X 100mm thick under 150mm diameter drain pipes including haunching up sides of pipes to not less than half diameter of the pipes and necessary formwork (Drain pipes measured separately)

m

12.70

B005

Extra over concrete bed to 100mm diameter pipe for Concrete Grade 20 surround minimum 150mm thick.

m

5.20

B006

Extra over concrete bed to 150mm diameter pipe for Concrete Grade 20 surround minimum 150mm thick.

m

7.30

B007

Supply and cast reinforced concrete Grade 20 in bottom of manholes, concrete beds, etc. With 20mm to 10mm granite mechanically mixed, including formwork.

m3

96.00

SOR Page 3 Item

Description of Works (C) BRC

Unit

Rate ($)

* BRC or other approved fabric reinforcement laid in position well lapped at joint (measured nett no allowance for laps * (C001 C006) C001

BRC No. C8

m2

6.20

C002

BRC No. C7

m2

5.10

C003

BRC No. C6

m2

4.20

C004

BRC No. A8

m2

4.90

C005

BRC No. A7

m2

3.90

C006

BRC No. A6

m2

3.10

SOR Page 4 Item

Description of Works (D) STEEL AND IRON WORKS

Unit

Rate ($)

Metal scaffolding/Bracket/Steel Holderbats Chequered Plate D001

Erection of metal scaffolding not exceeding 15 metres in height and including taking down after use

m2

11.50

D002

Erection of metal scaffolding exceeding 15 metres but not exceeding 35m in height after including taking down after use

m2

12.70

D003

Purpose made mild steel pipe brackets to pipe not exceeding 100mm diameter (Scaffolding measured separately)

No.

6.60

D004

Cast iron pipe brackets to soil waste or rainwater down pipes not exceeding 100mm diameter (Scaffolding measured separately)

No.

5.10

D005

Cast iron pipe brackets to soil waste or rainwater down pipes exceeding 100mm diameter (Scaffolding measured separately)

No.

6.60

D006

Mild steel compression bracket in replacement comprising two rings size 40mm wide, 5mm thick and 100mm diameter threaded rods not exceeding 300mm long including painting.

No.

28.90

D007

Chromium plated brackets to 15mm diameter stainless steel/copper pipe

No.

2.30

D008

Galvanised steel holder bats or clips for water pipes not exceeding 25mm diameter

No.

1.30

D009

Galvanised steel holder bats or clips for water pipes exceeding 25mm but not exceeding 50mm diameter

No.

1.30

D010

Galvanised steel holder bats or clips or water pipes exceeding 50mm diameter

No.

2.00

D011

6mm thick aluminium chequered plate cover circular on plan for grease interceptor for eating housing/canteen/food centre.

m2

1099.20

Mild Steel Hanger / Bolts Nuts / Steel Hanger * Erect of tubular steel staging including platform board, swivel castors or base plate etc and taking down after use *(D012 D013) D012

Per stage of exceeding 6 metres and not exceeding 8 metres high

No.

75.50

D013

Per stage of exceeding 8 metres and not exceeding 10 metres high

No.

90.00

SOR Page 5 Item

Description of Works Mild Steel Hanger / Bolts Nuts / Steel Hanger

Unit

Rate ($)

D014

Mild steel hangers for 75 mm diameter UPWC waste or soil pipe

No.

13.40

D015

Mild steel hangers for 100mm diameter galvanised UPVC pipe

No.

16.60

D016

Galvanised flanged plates to 100mmm diameter galvanised iron pipe

No.

12.70

D017

13mm diameter blots, nuts and washers for flange joint or outer fitting

No.

2.00

D018

17mm wide punched steel for hanging cast iron pipe etc (Band not exceeding 1.0 meter long)

No.

6.20

SOR Page 6 Item

Description of Works (E) MANHOLE

Unit

Rate ($)

Manhole Construction E001

225mm thick (average) concrete Grade 20 benching and haunching to bottom of manholes finished off at a gradient of one in six trowelled smooth with coves to 25mm radius at walls and rounded edged near channels including working carefully to edge of channels (Channels measured separately)

m2

32.60

E002

150mm thick concrete Grade 20 top slab reinforced with BRC No. C8 reinforcement including formwork and forming opening for frames.

m2

26.80

E003

100mm diameter half round salt-glazed stoneware straight or curved branch channels including bedding and jointing in cement mortar (1:1). (Per No. mean per channel)

No.

11.20

E004

150mm diameter half round salt-glazed stoneware straight or curved main channels including bedding and jointing in cement mortar (1:1). (Per No. means per channel)

No.

12.00

E005

100 – 150mm diameter half round salt-glazed stoneware taper piece including bedding and jointing in cement mortar (1:1)

No.

12.60

E006

225mm thick brick works in manhole in cement mortar (1:3)

m2

53.60

E007

20mm thick cement and sand (1:2) rendering to internal surfaces of manhole

m2

7.20

Manhole Cover E008

32 Kg cast iron light duty manhole cover ad frame including settling frame in cement mortar (1:3) and sealing cover in grease and fine sand.

No.

35.00

E009

22 Kg cast iron light duty manhole cover only (excluding frame)

No.

32.00

E010

52 Kg cast iron heavy duty manhole cover only (excluding frame)

No.

55.10

E011

600 X 450mm recessed type cast iron manhole cover and frame

No.

37.20

E012

Mild steel cover and frame 300 X 300mm for rain water down pipe sump

No.

24.50

E013

“PC” Brand or other approved cast iron light duty manhole cover with lifting device only (excluding frame)

No.

32.40

E014

“PC” Brand or other approved cast iron light duty frame only (excluding cover)

No.

32.50

SOR Page 7 Item E015

Description of Works “PC” Brand or other approved cast iron light duty lifting key only (excluding cover and frame)

Unit No.

Rate ($) 5.20

E016

Cut 2mm line at handle-area of cast iron manhole cover.

Cover

2.70

E017

Supply and install double-triangle (approx. 620mm X 620mm) cast iron heavy duty manhole cover and frame (approximately 205kg including setting frame in cement mortar and sealing cover in grease and fine sand, including removal of damaged cover & frame

No.

250.00

SOR Page 8 Item

Description of Works (F) STONE PIPES

Unit

Rate ($)

F001

100mm diameter salt-glazed stoneware drain pipe in flexible joint including laying on concrete bed in trench (trench and concrete bed measured separately)

m

21.00

F002

150mm diameter salt-glazed stoneware drain pipe in flexible joint including laying on concrete bed in trench (Trench and concrete bed measured separately)

m

24.50

F003

225mm diameter salt-glazed stoneware drain pipe in flexible joint including laying on concrete bed in trench (Trench and concrete bed measured separately)

m

32.05

F004

300mm diameter salt-glazed stoneware drain pipe in flexible joint including laying on concrete bed in trench (Trench and concrete bed measured separately)

m

62.25

F005

Extra over 100mm diameter salt-glazed stoneware drain pipes or bends including concrete surround.

No.

23.90

F006

Extra over 150mm diameter salt-glazed stoneware drain pipes or bends including concrete surround.

No.

46.90

F007

Extra over 225mm diameter salt-glazed stoneware drain pipes or bends including concrete surround.

No.

86.40

F008

Extra over 300mm diameter salt-glazed stoneware drain pipes or bends including concrete surround.

No.

207.15

SOR Page 9 Item

Description of Works (G) CAST IRON PIPE AND FITTINGS

Unit

Rate ($)

Cast Iron Pipe * Heavy Grade Coated Cast Iron Drain Pipes including necessary accessories and flexible joints laid in trench (Trench and Concrete bed measured separately) *(G001 G004) G001

100mm diameter drain pipe

m

19.90

G002

150mm diameter drain pipe

m

31.00

G003

Extra over 100mm diameter pipe for “duck” foot bend

No.

41.80

G004

Extra over 150mm diameter pipe for “duck” foot bend

No.

55.60

* Medium Grade Coated Cast Iron soil, waste ventilating and anti syphonage pipes and fittings and provision of extra brackets if required *(G005 G031) G005

50mm diameter cast iron pipes with socketted joints caulked with hemp and molten lead.

m

16.80

G006

75mm diameter cast iron pipes with socketted joints caulked with help and molten lead.

m

20.30

G007

100mm diameter cast iron pipes with socketted joints caulked with hemp and molten lead.

m

22.80

G008

150mm diameter cast iron pipes with socketted joints caulked with hemp and molten lead

m

32.90

Cast Iron Fittings G009

50mm diameter cast iron bend with cleaning eye.

No.

10.40

G010

75mm diameter cast iron bend with cleaning eye

No.

13.80

G011

100mm diameter cast iron bend with cleaning eye

No.

18.45

G012

150mm diameter cast iron bend with cleaning eye

No.

22.60

G013

50mm diameter equal or unequal cast iron junction or tee with cleaning eye.

No.

11.90

G014

75mm diameter equal or unequal cast iron junction or tee with cleaning eye.

No.

15.50

G015

100mm diameter equal or unequal cast iron junction or tee with cleaning eye

No.

17.90

G016

150mm diameter equal or unequal cast iron junction or tee with cleaning eye

No.

37.40

G017

75mm to 50mm diameter cast iron reducer.

No.

12.00

G018

100mm to 75mm diameter cast iron reducer.

No.

12.70

SOR Page 10 Item G019

Description of Works 75mm diameter short length cast iron pipes with cleaning eye not exceeding 30mm in length

Unit No.

Rate ($) 12.40

G020

100mm diameter short length cast iron pipes with cleaning eye not exceeding 300mm in length

No.

14.10

G021

150mm diameter short length cast iron pipes with cleaning eye not exceeding 300mm in length

No.

21.40

G022

Steel blot for cast iron inspection covers.

No.

0.60

G023

Cast iron cover plate to cleaning eye including all necessary bolts etc to 50mm diameter pipe, bend, etc.

No.

3.10

G024

Cast iron cover plate to cleaning eye including all necessary bolts etc to 75mm diameter pipe, bend, etc.

No.

3.40

G025

Cast iron cover plate to cleaning eye including all necessary bolts etc to 100mm diameter pipe, bend, etc.

No.

3.50

G025

Cast iron cover plate to cleaning eye including all necessary bolts etc to 150mm diameter pipe, bend, etc.

No.

3.70

G027

Cast iron heavy duty 100mm diameter “duck” foot bend including breaking up concrete floor.

No.

72.10

G028

100mm diameter cast iron heavy duty union socket for underground pipes

No.

24.50

G029

Cast iron downspout outlet fixed to 75mm diameter cast iron pipe with three numbers of tightening bolts

No.

18.80

G030

225mm X 450mm cast iron purpose made street gully with 100mm outlet including connection, all necessary excavation and concrete surround.

No.

149.80

G031

100mm diameter cast iron coupling joint including all necessary bolts and nuts

No.

174.10

SOR Page 11 Item

Description of Works (H) DUCTILE IRON PIPES AND FITTINGS

Unit

Rate ($)

* Ductile Iron Cement Lined Water Pipes with spigot and socket joints and necessary fittings / accessories and brackets / supports including hacking hole through floors or walls or on roofs (with supports where necessary) *(H001 H042) Ductile Iron Pipes H001

80mm diameter water pipes

m

37.05

H002

100mm diameter water pipes

m

38.35

H003

150mm diameter water pipes

m

50.50

Fittings H004

80mm diameter bends 300mm ling including making necessary extra joints (with cleaning eye)

No.

33.10

H005

80mm diameter tees including making necessary extra joints

No.

57,30

H006

Extra over for bolted flange joints including all necessary drilling, bolts and gaskets (For items H001; H004 & H005)

Joint

7.10

H007

80mm diameter collars

No.

24.70

H008

80mm diameter socket and flanged connector.

No.

38.70

H009

100mm diameter bends 300mm long including making necessary extra joints.

No.

34.90

H010

100mm diameter tees including making necessary extra joint

No.

65.10

H011

Extra over for bolted flange joints including all necessary drilling bolts and gaskets (For items H002; H009 & H010)

Joint

15.50

H012

100mm diameter double flanged “duck” foot bend

No.

48.00

H013

100mm diameter double socket long bend

No.

57.90

H014

100mm diameter collar

No.

76.20

H015

100mm diameter flanged socket

No.

36.20

H016

100mm diameter flange spigot

No.

49.40

H017

100mm diameter flange tee

No.

75.40

H018

100mm diameter flange elbow

No.

39.70

H019

100mm diameter flanged lengthening piece not exceeding 300mm long.

No.

64.20

SOR Page 12 Item H020

Description of Works 100mm diameter double flanged lengthening piece exceeding 300mm but not exceeding 600mm long.

Unit No.

Rate ($) 104.80

H021

100mm diameter double flanged lengthening piece exceeding 600mm but not exceeding 900mm long.

No.

110.50

H022

215mm diameter flange washer for water mains.

No.

8.20

H023

100mm X 300mm bend

No.

42.80

H024

150mm diameter “duck” foot bend

No.

72.60

H025

150mm diameter bend 300mm long

No.

50.60

H026

150mm diameter tee

No.

116.10

H027

150mm to 100mm diameter reducer for wash-out pipe including making necessary extra joints

No.

63.60

H028

Extra over for bolted flange joints including all necessary drilling bolts and gaskets. (For items H003; H025 & H026)

Joint

30.80

H029

Cement lining for 100mm diameter ductile iron fitting

No.

H030

Cement lining for 150mm diameter ductile iron fitting

No.

7.20

H031

100 X 50m ductile iron cement lined flange tee

No.

61.70

H031

50mm diameter ductile iron blank

No.

11.20

H033

80mm diameter ductile iron blank

No.

22.50

H034

100mm diameter ductile iron blank

No.

26.20

6.30

Ductile Iron - Underground Pipe H035

80mm diameter ductile iron cement lined heavy duty pipes (push-on Joint “T” type or Mechanical Joint accessories and flexible joints laid in trench (trench and concrete bed measured separately)

m

31.30

H036

100mm diameter ductile iron cement lined heavy duty pipes (Push-on Joint ‘T’ type or Mechanical Joint ‘K’ type) including necessary accessories and flexible joints laid in trench (Trench and concrete bed measured separately)

m

34.45

H037

150mm diameter ductile iron cement lined heavy duty pipes (Push-on Joint ‘T’ type or Mechanical Joint ‘K’ type ) including necessary accessories and flexible joints laid in trench (Trench and concrete bed measured separately)

m

45.90

H038

Extra over ductile iron pipe for 80mm diameter bend (all angles)

m

16.50

H039

Extra over ductile iron pipe for 100 diameter bend (all angles)

m

19.40

Unit m

Rate ($) 37.00

SOR Page 13 Item H040

Description of Works Extra over ductile iron pipe or 150mm diameter bend (all angles) UPVC Pipe Cover for Rooftop Water Main

H041

150mm diameter half channel UPVC pipe (SS213 cover to main water distribution pipe at roof top excluding half channel clip

m

9.10

H042

150mm diameter UPVC half channel clip.

No.

5.50

SOR Page 14 Item

Description of Works (I) GALVAISED STEEL PIPES AND FITTINGS

Unit

Rate ($)

Galvanised Steel Pipes * UPVC Lined Galvanised Steel Water Pipe including Accessories and fitting including cutting off of existing pipes and accessories, re-threading, all joints and providing additional holder bats and cutting hole through walls if necessary *(I001 I009) I001

15mm diameter UPVC lined galvanised steel water pipe fixed to wall.

m

9.90

I002

20mm diameter UPVC lined galvanised steel water pipe fixed to wall.

m

10.90

I003

25mm diameter UPVC lined galvanised steel water pipe fixed to wall.

m

13.00

I004

32mm diameter UPVC lined galvanised steel water pipe fixed to wall.

m

15.10

I005

40mm diameter UPVC lined galvanised steel water pipe fixed to wall.

m

16.30

I006

50mm diameter UPVC lined galvanised steel water pipe fixed to wall.

m

20.70

I007

65mm diameter UPVC lined galvanised steel water pipe fixed to wall.

m

23.40

I008

75mm diameter UPVC lined galvanised steel water pipe fixed to wall.

m

33.00

I009

100mm diameter UPVC lined galvanised steel water pipe fixed to wall.

m

43.10

Fittings * Epoxy coated fittings for UPVC lined galvanised steel pipes including jointing *(I010 I027) I010

15mm Elbow

No.

3.90

I011

20mm Elbow

No.

4.00

I012

25mm Elbow

No.

4.65

I013

32mm Elbow

No.

6.70

I014

15mm Socket

No.

4.00

I015

20mm Socket

No.

4.20

I016

25mm Socket

No.

4.75

I017

32mm Socket

No.

5.85

SOR Page 15 Item I018

Description of Works 15mm Nipple

Unit No.

Rate ($) 4.30

I019

20mm Nipple

No.

4.45

I020

25mm Nipple

No.

4.90

I021

32mm Nipple

No.

6.15

I022

50mm Nipple

No.

14.00

I023

50mm X 15mm UPVC Lined galvanised reducing elbow.

No.

16.00

I024

15mm Tee

No.

4.30

I025

20mm Tee

No.

4.45

I026

25mm Tee

No.

5.75

I027

32mm Tee

No.

8.15

SOR Page 16 Item

Description of Works (J) UPVC PIPES AND FITTINGS

Unit

Rate ($)

Drain Pipes and Fittings for Underground * Approved UPVC Drain Pipe with flexible joints laid in trench (Trench and Concrete Bed measured separately) *(J001 J009) J001

100mm diameter drain pipe (SS 272)

m

6.50

J002

150mm diameter drain pipe (SS 272)

m

9.30

J003

200mm diameter drain pipe (SS 272)

m

14.60

J004

Extra over 100mm diameter pipe for bend (SS 272)

No.

3.20

J005

Extra over 150mm diameter pipe for bend (SS 272)

No.

5.90

J006

Extra over 200mm diameter pipe for bend (SS 272)

No.

46.60

Y-Junction (SS 272) J007

Extra over 100mm diameter Y-Junction

m

7.60

J008

Extra over 150mm diameter Y-Junction

m

9.30

J009

Extra over 200mm diameter Y-Junction

m

96.60

Soil/Waste Pipe (SS 213)- Normal Cutting * Approved Unplasticised Polyvinyl Chloride (UPVC) pipes (SS 213/SS 272) for rainwater, vent waste and soil pipes including normal cutting, joint and removal of existing pipes, provision of new saddle clips/ mild steel brackets where necessary and hacking of holes through walls or slabs and reinstate pipe numberings (Fittings measured separately) *(J010 J018) J010

32mm diameter UPVC pipe (SS 213)

m

3.50

J011

32mm diameter UPVC pipe (SS 213)

m

4.80

J012

32mm diameter UPVC pipe (SS 213)

m

4.00

J013

32mm diameter UPVC pipe (SS 213)

m

6.00

J014

32mm diameter UPVC pipe (SS 213)

m

6.70

J015

32mm diameter UPVC pipe (SS 213)

m

9.80

J016

32mm diameter UPVC pipe (SS 213)

m

17.80

J017

200 X 80 X 5mm thick rectangular pipe (SS 272)

m

36.03

J018

275 X 120 X 5mm thick rectangular pipe (SS 272

m

48.70

SOR Page 17 Item

Description of Works Sweep Junctions (SS 213/ SS 272)

Unit

Rate ($)

J019

32mm sweep junction (SS 213) without inspection opening

m

3.10

J020

40mm sweep junction (SS 213) without inspection opening

m

3.70

J021

50mm sweep junction (SS 213) without inspection opening

No.

3.70

J022

75mm sweep junction (SS 213) without inspection opening

No.

6.90

J023

100mm sweep junction (SS 213) without inspection opening

No.

9.10

J024

150mm sweep junction (SS 213) without inspection opening

No.

15.10

J025

75 X 50mm sweep junction (SS 213) without inspection opening

No.

6.10

J026

100 X 50mm sweep junctions (SS 213) without inspection opening

No.

5.30

J027

100 X 75mm sweep junctions (SS 213) without inspection opening

No.

6.10

J028

150 X 150mm reducing sweep junction without inspection opening (SS 213)

No.

19.90

J029

150 X 100mm reducing sweep junction without inspection opening (SS 213)

No.

14.10

J030

200 X 50mm reducing sweep junction without inspection opening (SS 213)

No.

40.80

J031

200 X 150mm reducing sweep junction without inspection opening (SS 213)

No.

21.60

J032

100 X 100 X 50 double sweep junction without inspection opening (SS 213)

No.

8.30

J033

100 X 100 X 60 double sweep junction without inspection opening (SS 213)

No.

11.20

J034

100 X 100 X 100mm double sweep junction without inspection opening (SS 213)

No.

10.20

J035

150 X 100 X 100 reducing sweep junction with inspection opening (SS 213)

No.

26.10

J036

150 X 150 X 100 reducing sweep junction with inspection opening (SS 213)

No.

49.60

SOR Page 18 Item

Description of Works Reducing Bush (SS 213)

Unit

Rate ($)

J037

100mm X 50mm reducing bush (SS 213)

No.

10.20

J038

100 X 75mm reducing bush (SS 213)

No.

20.25

J039

75mm X 50mm reducing bush (SS 213)

No.

6.10

Socket (SS 213 / SS 272) J040

32mm socket (plain coupling) (SS 213)

No.

2.70

J041

40mm socket (plain coupling) (SS 213)

No.

2.70

J042

50mm socket (plain coupling) (SS 213)

No.

3.50

J043

75mm socket (plain coupling) (SS 213)

No.

4.10

J044

100mm socket (plain coupling) (SS 213)

No.

5.60

J045

150mm socket (plain coupling) (SS 213)

No.

10.30

J046

200mm connector piece (SS 272)

No.

45.20

Bend and Elbow (SS 213 / SS 272) J047

32mm Bend (any Angles) and Elbow (SS 213) plain (Inspection opening including access cap measured separately)

No.

2.40

J048

40mm Bend (any Angles) and Elbow (SS 213) plain (Inspection opening including access cap measured separately)

No.

2.80

J049

50mm Bend (any Angles) and Elbow (SS 213) plain (Inspection opening including access cap measured separately)

No.

2.40

J050

75mm Bend (Any Angles) and Elbow (SS 213) plain (Inspection opening including access cap measured separately)

No.

4.00

J051

100mm Bend (Any Angles) and Elbow (SS 213) plain (Inspection opening including access cap measured separately)

No.

3.70

J052

150mm Bend (Any Angles) and Elbow (SS 213) plain (Inspection opening including access cap measured separately)

No.

6.20

J053

120 X 275mm rectangular elbow (SS 272) plain (Inspection opening including access cap measured separately)

No.

142.90

SOR Page 19 Item

Description of Works Reducers (SS 213)

Unit

Rate ($)

J054

100 X 50mm reducing bend (SS 213)

No.

8.40

J055

100 X 75mm Reducer (SS 213)

No.

7.40

J056

150 X 100mm Reducer (SS 213)

No.

11.60

J057

150 X 100mm level invert reducers (SS 213)

No.

11.70

J058

100 X 75mm level invert reducers (SS 213)

No.

7.80

J059

100 X 50mm level invert reducers (SS 213)

No.

6.70

Adaptor (SS 213/SS 272) J060

80mm diameter adaptor (SS 213)

No.

4.60

J061

100mm diameter adaptor (SS 213)

No.

4.90

J062

150mm diameter adaptor (SS 213)

No.

6.10

J063

200mm diameter X 275 X 120mm adaptor (SS 272)

No.

141.10

Testing Opening / Access Cap J064

75mm diameter testing openings (F & F) including the access cap

Set

12.00

J065

100mm diameter testing opening (F & F) including the access cap

Set

14.80

J066

150mm diameter testing openings (F & F) including the access cap

Set

23.00

J067

Extra over UPVC fitting (various sizes) for inspection opening (cleaning eye) including access cap

No.

7.40

J068

75m diameter UPVC socket (Screw-on type) for SS 213 pipe

No.

4.50

J069

100mm diameter UPVC socket (Screw-on type) for SS 213 pipe

No.

5.00

J070

50mm/100mm diameter access cap with screw thread to UPVC pipe.

No.

2.25

J071

150mm diameter access cap with screw to UPVC pipes

No.

4.00

J072

Vent Pipe Fitting

No.

2.20

J073

100 diameter UPVC vent cowl to vent pipe

No.

4.80

SOR Page 20 Item

Description of Works Steel / Collar Bracket

Unit

Rate ($)

J074

Steel collar bracket with hop dip for UPVC soil/ waste pipes 75mm diameter for SS 141 pipe

No.

4.80

J075

Ditto but 100mm diameter

No.

4.90

J076

Ditto but 150mm diameter

No.

5.10

J077

Steel collar bracket with hop dip for UPVCsoil/waste pipes 75mm diameter for SS141 pipe.

No.

6.10

J078

Ditto but 100mm diameter

No.

6.35

J079

Ditto but 150mm diameter

No.

6.45

J080

150mm diameter UPVC U-trap body for rooftop vent pipe (SS 213)

No.

14.50

J081

Ditto but 100m diameter (SS 213)

No.

6.20

Plasma Cutting to Soil Waste Pipe Approved Unplastcised Polyvinyl Chloride UPVC Pipes (SS 213) for rainwater, vent, waste and soil pipes all in replacement including plasma cutting (measured separately), jointing and removal of existing pipe; provision of new saddle and hacking of holes through walls or slabs and reinstate pipe numbering (Fitting measured separately) * (J082 J087) J082

32mm dia UPVC pipe (SS 213)

m

3.00

J083

40mm dia UPVC pipe (SS 213)

m

3.20

J084

50mm dia UPVC pipe (SS 213)

m

3.90

J085

75mm dia UPVC pipe (SS 213)

m

6.40

J086

100mm dia UPVC pipe (SS 213)

m

7.10

J087

150mm dia UPVC pipe (SS 123)

m

11.30

* Replacement of Cast Iron Pipes Using UPVC Connector and Adaptor cut the existing cast iron pipe using “Air Plasma Cutting System” or other equivalent method and removed off site of size J088

50mm diameter

No.

15.00

J089

75mm diameter

No.

16.50

J090

100mm diameter

No.

18.20

J091

125mm diameter

No.

19.90

J092

150 diameter

No.

21.60

SOR Page 21 Item

Description of Works Adaptor (For jointing of cast iron pipe)

Unit

Rate ($)

* Supply and install of the following UPVC adaptors (SS 213) including cutting to the required length and approved sealant to the interface between the adaptor and the existing pipe *(J093 J102) J093

48mm diameter spigot adaptor for existing 50mm cast iron pipe

No.

18.10

J094

72mm diameter spigot adaptor for existing 80mm cast iron pipe

No.

26.90

J095

65mm diameter spigot adaptor for existing 80mm cast iron vent pipe

No.

26.90

J096

95mm or 96mm diameter spigot adaptor for existing 100mm cast iron pipe

No.

26.50

J097

96mm diameter spigot adaptor for existing 100mm cast iron ‘S’ Bend

No.

29.50

J098

88mm diameter off-set Pan Collar

No.

18.70

J099

95mm diameter Pan Collar Adaptor for existing 100mm diameter cast iron pipe

No.

28.20

J100

148mm diameter spigot adaptor for existing 150mm cast iron pipe

No.

39.60

J101

95mm diameter grating adaptor for existing 100mm diameter cast-iron pipe with one/two side inlets irrespective of size

No.

33.30

J102

117mm diameter grating adaptor for existing 125mm diameter cast-iron pipe with one/two side inlets irrespective of size

No.

34.50

Rubber Ring Connector * Supply and install of the following UPVC connectors (SS 213 including applying on one layer of silicone bonding agent to the outside surface of the protruding cast iron pipe *(J103 J109) J103

Rubber ring 50mm diameter w.c. straight connector with spigot not exceeding 100mm long

No.

16.80

J104

Rubber ring 80mm diameter w.c. straight connector with spigot not exceeding 100mm long

No.

18.10

J105

Rubber ring 100mm diameter w.c. straight connector with spigot not exceeding 100mm long

No.

19.40

J106

Rubber ring 100mm diameter w.c. straight connector with spigot exceeding 100mm but not exceeding

No.

24.40

150mm long

SOR Page 22 Item J107

Description of Works Rubber ring 125m diameter w.c. straight connector with spigot not exceeding 100mm long

Unit No.

Rate ($) 25.40

J108

Rubber ring 125m diameter w.c. straight connector with spigot exceeding 100mm but not exceeding 150mm long

No.

26.90

J109

Rubber ring 150mm, diameter w.c. straight connector with spigot not exceeding 100mm long

No.

27.50

UPVC Pipes (SS 141) Approved Polyvinyl Chloride (UPVC) water supply pipes (SS 141) including cutting, joining and removal of existing pipes, provision of new saddle clip/mild steel brackets where necessary and hacking of hole through walls or slabs (Fitting measured separately) *(J110 J119) J110

15mm diameter UPVC pipe (SS 141)

m

2.50

J111

20mm diameter UPVC pipe (SS 141)

m

2.80

J112

25mm diameter UPVC pipe (SS 141)

m

3.40

J113

32mm diameter UPVC pipe (SS 141)

m

4.00

J114

40mm diameter UPVC pipe (SS 141)

m

4.60

J115

50mm diameter UPVC pipe (SS 141)

m

5.80

J116

65mm diameter UPVC pipe (SS 141)

m

6.60

J117

75mm diameter UPVC pipe (SS 141)

m

9.60

J118

100mm diameter UPVC pipe (SS 141)

m

11.20

J119

150mm diameter UPVC pipe (SS 141)

m

19.40

* Supply and fix the following (UPVC) fittings (SS 141) including jointing *(J120 J196) J120

15mm Tee (SS 141)

No.

2.70

J121

20mm Tee (SS 141)

No.

2.80

J122

25mm Tee (SS 141)

No.

3.00

J123

32mm Tee (SS 141)

No.

4.60

J124

40mm Tee (SS 141)

No.

5.10

J125

50mm Tee (SS 141)

No.

8.40

J126

75mm Tee (SS 141)

No.

14.70

J127

20 X 15mm Reducing Tee (SS 141)

No.

2.70

SOR Page 23 Item J128

Description of Works 25 X 15mm Reducing Tee (SS 141)

Unit No.

Rate ($) 3.00

J129

40 X 15mm Reducing Tee (SS 141)

No.

5.60

J130

40 X 25mm Reducing Tee (SS 141)

No.

5.40

J131

50 X 40mm Reducing Tee (SS 141)

No.

8.40

J132

65 X 20mm Reducing Tee (SS 141)

No.

6.30

J133

75 X 50mm Reducing Tee (SS 141)

8.60

Connector / Socket (SS 141) J134

15mm Connector or Socket (SS 141)

No.

2.60

J135

20mm Connector or Socket (SS 141)

No.

2.60

J136

25mm Connector or Socket (SS 141)

No.

2.70

J137

32mm Connector or Socket (SS 141)

No.

3.30

J138

40mm Connector or Socket (SS 141)

No.

3.90

J139

50mm Connector or Socket (SS 141)

No.

4.70

J140

65mm Connector or Socket (SS 141)

No.

6.30

J141

75mm Connector or Socket (SS 141)

No.

9.20

Reducer (SS 141) J142

20mm to 15mm Reducer (SS 141)

No.

2.70

J143

25mm to 15mm Reducer (SS141)

No.

2.70

J144

25mm to 20mm Reducer (SS 141)

No.

2.80

J145

32mm to 25mm Reducer (SS 141)

No.

2.70

J146

40mm to 32mm Reducer (SS 141)

No.

3.30

J147

50mm to 25mm Reducer (SS 141)

No.

3.70

J148

50mm to 40mm Reducer (SS 141)

No.

4.00

J149

75mm to 50mm Reducer (SS 141)

No.

11.00

Bend and Elbow (SS 141) J150

15mm Bend (any Angles) and Elbow (SS 141)

No.

2.20

J151

20mm Bend (any Angles) and Elbow (SS 141)

No.

2.20

J152

25mm Bend (any Angles) and Elbow (SS 141)

No.

2.40

J153

32mm Bend (any Angles) and Elbow (SS 141)

No.

3.20

SOR Page 24 Item J154

Description of Works 40mm Bend (any Angles) and Elbow (SS 141)

Unit No.

Rate ($) 4.50

J155

50mm Bend (any Angles) and Elbow (SS 141)

No.

5.90

J156

75mm Bend (any Angles) and Elbow (SS 141)

No.

15.10

Valve Socket (SS 141) J157

15mm Valve Socket (SS 141)

No.

2.20

J158

20mm Valve Socket (SS 141)

No.

2.20

J159

25mm Valve Socket (SS 141)

No.

2.30

J160

32mm Valve Socket (SS 141)

No.

3.40

J161

40mm Valve Socket (SS 141)

No.

3.50

J162

50mm Valve Socket (SS 141)

No.

4.00

J163

65mm Valve Socket (SS 141)

No.

4.40

J164

75mm Valve Socket (SS 141)

No.

10.00

Faucet Socket J165

15mm Faucet Socket (SS 141)

No.

2.20

J166

20mm Faucet Socket (SS 141)

No.

2.50

J167

25mm Faucet Socket (SS 141)

No.

2.80

J168

32mm Faucet Socket (SS 141)

No.

3.20

J169

40mm Faucet Socket (SS 141)

No.

3.40

J170

50mm Faucet Socket (SS 141)

No.

4.40

J171

15mm Faucet Socket (SS 141)

No.

2.40

J172

20mm Faucet Socket (SS 141)

No.

2.70

J173

20mm Faucet Socket (SS 141)

No.

3.50

Simple Joint (SS 141) J174

15mm Simple Joint (SS 141)

No.

1.90

J175

22mm Simple Joint (SS 141)

No.

2.20

J176

28mm Simple Joint (SS 141)

No.

2.30

J177

35mm Simple Joint (SS 141)

No.

8.30

J178

40mm Simple Joint (SS 141)

No.

7.70

J179

50mm Simple Joint (SS 141)

No.

9.70

SOR Page 25 Item

Description of Works End Cap

Unit

Rate ($)

J180

15mm End Cap

No.

1.90

J181

20mm End Cap

No.

2.10

J182

25mm End Cap

No.

2.20

J183

32mm End Cap

No.

2.80

J184

40mm End Cap

No.

2.90

J185

50mm End Cap

No.

3.30

J186

65mm End Cap

No.

4.10

J187

70mm End Cap

No.

7.20

Saddle Clip J188

16mm Saddle Clip

No.

1.10

J189

22mm Saddle Clip

No.

1.20

J190

28mm Saddle Clip

No.

1.20

J191

36mm Saddle Clip

No.

1.30

J192

42mm Saddle Clip

No.

1.30

J193

54mm Saddle Clip

No.

1.40

Adaptor (SS 141) J194

80mm PVC Adaptor (SS 141)

No.

6.85

J195

Ditto but 100mm (SS 141)

No.

7.15

J196

Ditto but 150mm (SS 141)

No.

7.90

SOR Page 26 Item

Description of Works (K) STAINLESS STEEL PIPES, COPPER PIPES & FITTINGS

Unit

Rate ($)

Stainless Steel Pipes K001

15mm diameter (outside diameter) stainless steel pipes to B.S. 4127 including holderbats or clips and cutting of old pipes (fitting measured separately)

m

6.90

K002

22mm diameter (outside diameter) stainless steel pipes to B.S. 4127 including holderbats or clips and cutting of old pipes (fitting measured separately)

m

9.10

K003

28mm diameter (outside diameter) stainless steel pipes to B.S. 4127 including holderbats or clips and cutting of old pipes (fitting measured separately)

m

12.30

K004

35mm diameter (outside diameter) stainless steel pipes to B.S. 4127 including holderbats or clips and cutting of old pipes (fitting measured separately)

m

17.30

K005

42mm diameter (outside diameter) stainless steel pipes to B.S. 4127 including holderbats or clips and cutting of old pipes (fitting measured separately)

m

21.00

K006

54mm diameter (outside diameter) stainless steel pipes to B.S. 4127 including holderbats or clips and cutting of old pipes (fitting measured separately)

m

24.20

Copper Pipe K007

13mm diameter copper pipes including holderbats or clips and cutting of old pipes (fittings measured separately).

m

8.40

K008

20mm diameter copper pipes including holderbats or clips and cutting of old pipes (fittings measured separately).

m

10.90

K009

25mm diameter copper pipes including holderbats or clips and cutting of old pipes (fittings measured separately).

m

12.60

K010

40mm diameter copper pipes including holderbats or clips and cutting of old pipes (fittings measured separately).

m

18.50

K011

50mm diameter copper pipes including holderbats or clips and cutting of old pipes (fittings measured separately).

m

20.80

Supply and fix the following brass fittings for copper/stainless steel pipes (DZR Type) * (K012 K076) Elbows

K012

15mm diameter Elbows

No.

3.90

SOR Page 27 Item K013

Description of Works 15mm diameter Flanged Elbows

Unit No.

Rate ($) 4.10

K014

22mm diameter Elbows

No.

5.70

K015

28mm diameter Elbows

No.

7.90

K016

35mm diameter Elbows

No.

12.80

K017

42mm diameter Elbows

No.

17.50

K018

54mm diameter Elbows

No.

29.00

Coupling K019

15mm diameter Coupling

No.

3.60

K020

22mm diameter Coupling

No.

4.70.

K021

28mm diameter Coupling

No.

7.20

K022

35mm diameter Coupling

No.

10.70

K023

42mm diameter Coupling

No.

15.20

K024

54mm diameter Coupling

No.

20.10

Union K025

15mm diameter Union

No.

3.90

K026

22mm diameter Union

No.

4.70

K027

28mm diameter Union

No.

7.50

K028

35mm diameter Union

No.

8.30

K029

42mm diameter Union

No.

10.90

K030

54mm diameter Union

No.

16.70

K031

42 X 54mm diameter Union

No.

17.60

K032

42 X 35mm diameter Union

No.

12.50

K033

35 X 54mm diameter Union

No.

16.90

K034

35 X 28mm diameter Union

No.

9.50

K035

28 X 15mm diameter Union

No.

5.90

K036

20 X 15mm diameter Union

No.

7.00

No.

4.20

Tee K037

15 X 15 X 15mm Tees

K038

22 X 22 X 22mm Tees

No.

6.40

K039

28 X 28 X 28mm Tees

No.

8.70

SOR Page 28 Item K040

Description of Works 42 X 42 X 42mm Tees

Unit No.

Rate ($) 15.20

K041

54 X 54 X 54mm Tees

No.

23.60

K042

28 X 15 X 28mm Tees

No.

6.80

K043

22 X 15 X 22mm Tees

No.

5.50

K044

42 X 28 X 42mm Tees

No.

14.90

K045

54 X 42 X 54mm Tees

No.

23.10

K046

28 X 22 X 28mm Tees

No.

8.00

K047

35 X 15 X 35mm Tees

No.

14.30

K048

15 X 22 X 15mm Tees

No.

5.20

K049

28 X 35 X 28mm Tees

No.

13.20

K050

54 X 28 X 54mm Tees

No.

22.90

K051

54 X 35 X 54mm Tees

No.

23.60

K052

42 X 22 X 42mm Tees

No.

17.80

K053

42 X 15 X 42mm Tees

No.

20.20

Reducing Elbow K054

22 x 13mm Reducing Elbow

No.

4.80

K055

22 x 13mm Reducing Elbow

No.

4.90

K056

22 x 13mm Reducing Elbow

No.

8.20

K057

22 x 13mm Reducing Elbow

No.

7.30

K058

22 x 13mm Reducing Elbow

No.

10.00

K059

22 x 13mm Reducing Elbow

No.

21.30

K060

22 x 13mm Reducing Elbow

No.

23.60

K061

22 x 13mm Reducing Elbow

No.

12.10

K062

54 x 35mm Reducing Elbow

No.

26.60

K063

54 x 42mm Reducing Elbow

No.

27.40

K064

42 x 28mm Reducing Elbow

No.

13.80

K065

35 x 15mm Reducing Elbow

No.

10.10

K066

42 x 15mm Reducing Elbow

No.

12.10

SOR Page 29 Item

Description of Works Stop End

Unit

Rate ($)

K067

42mm diameter brass stop end.

No.

19.40

K068

54mm diameter brass stop end.

No.

13.10

K069

54mm diameter brass nipple.

No.

11.70

Coupling Washer K070

13mm diameter coupling washer

No.

1.00

K071

20mm diameter coupling washer

No.

1.50

K072

30mm diameter coupling washer

No.

1.60

K073

40mm diameter coupling washer

No.

2.00

K074

50mm diameter coupling washer

No.

2.10

K075

75mm diameter coupling washer

No.

2.30

K076

100mm diameter coupling washer

No.

2.90

SOR Page 30 Item

Description of Works (L) SANITARY FITTINGS AND ACCESSORIES

Unit

Rate ($)

* Supply and fix the following sanitary fittings and accessories *(L001 L122) Fireclay Sink L001

600 X 450 X 200mm white fireclay sink complete with cantilever brackets, 40mm vulcanite plug and chain, all necessary trap, waste pipe and fittings.

No.

113.00

L002

685 X 450 X 250mm white fireclay sink complete with cantilever brackets, 40mm vulcanite plug and chain, all necessary trap, waste pipe and fittings.

No.

131.40

L003

600 X 450 X 250mm white fireclay sink complete with 40mm vulcanite plug and chain, all necessary trap, waste pipe and fittings.

No.

96.50

L004

685 X 450 X 250mm white fireclay sink complete with 40mm vulcanite plug and chain, all necessary trap, waste pipe and fittings.

No.

114.80

No.

93.80

L005

Wash Hand Basin 500 X 400mm white vitreous China locally made wash hand basin complete with pillar tap (push button spring type) cantilever brackets, vulcanite plug and chain, all necessary trap, waste pipe and fittings.

L006

500 X 400mm coloured vitreous China locally made wash hand basin complete with pillar tap (push button spring type) cantilever brackets, vulcanite plug and chain, all necessary trap, waste pipe and fittings.

No.

102.50

L007

500 X 400mm coloured with pedestal stand vitreous China locally made wash hand basin complete with pillar tap (push button spring type) cantilever brackets, vulcanite plug and chain, all necessary trap, waste pipe and fittings.

No.

152.20

L008

500 X 400mm white vitreous China locally made wash hand basin complete with pillar tap (delay action type) cantilever brackets, vulcanite plug and chain, all necessary trap, waste pipe and fittings

No.

137.40

L009

500 X 400mm coloured vitreous China locally made wash hand basin complete with pillar tap (delay action type) cantilever brackets, vulcanite plug and chain, all necessary trap, waste pipe and fittings

No.

146.10

L010

500 X 400mm coloured with pedestal stand vitreous China locally made wash hand basin complete with pillar tap (delay action type) cantilever brackets, vulcanite plug and chain, all necessary trap, waste pipe and fittings.

No.

195.80

SOR Page 31 Item L011

Description of Works Integral coloured cultured marble basin and top of approximate size 525 X 1500mm with backsplash, 200mm front apron complete with integrated basin, approved single lever mixer tap with pop-up waste, bottle trap, waste pipe and galvanised steel bracket for fixing to wall, and all necessary accessories for fixing and jointing to pipework

Unit No.

Rate ($) 494.90

L012

550 X 450mm stainless steel wash hand basin complete with pillar tap, cantilever brackets, vulcanite plug and chain, all necessary trap, waste pipe and fittings.

No.

57.40

Sink L013

1000 X 500mm single bowl single drainer S.W.G. 2.03mm anodised aluminium sink complete with cantilever brackets 40mm vulcanite plug and chain, all necessary trap, waste pipe and fittings.

No.

111.30

L014

1500 X 500mm single bowl single drainer S.W.G. 2.03mm anodised aluminium sink complete with cantilever brackets 40mm vulcanite plug and chain, all necessary trap, waste pipe and fittings.

No.

142.80

L015

1067 X 457mm single bowl, single drainer stainless steel sink complete with cantilever brackets 40mm vulcanite plug and chain, all necessary trap, waste pipe and fittings.

No.

125.20

L016

1500 X 500mm locally made single bowl double drainer stainless steel sink complete with cantilever brackets 40mm vulcanite plug and cabin, all necessary trap, waste pipe and fittings.

No.

182.60

L017

1500 X 500mm locally made double bowl double drainer stainless steel sink complete with cantilever brackets 40mm vulcanite plug and cabin, all necessary trap, waste pipe and fittings.

No.

217.00

Waste Trap L018

32mm galvanised wrought iron ‘S’ trap for lavatory basin

No.

7.00

L019

40mm galvanised wrought iron ‘S’ trap for sink

No.

7.30

L020

50mm galvanised wrought iron ‘S’ trap.

No.

12.40

L021

32mm approved PVC ‘S’ trap

No.

6.30

L022

32mm approved PVC ‘P’ trap

No.

6.00

L023

40mm approved PVC ‘S’ trap

No.

10.20

L024

40mm approved PVC ‘S’ trap

No.

9.10

L025

50mm approved PVC ‘S’ trap

No.

10.20

L026

50mm approved PVC ‘P’ trap

No.

9.70

SOR Page 32 Item L027

Description of Works 100mm UPVC adjustable ‘S’ trap complete with hopper and vent with grating including jointing to waste pip

Unit No.

Rate ($) 13.70

L028.

100mm UPVC adjustable ‘P’ trap complete with hopper and vent with grating including jointing to waste pipe

No.

12.40

Waste Fitting L029

Brass waste fitting to sink or basin complete with brass cobweb grating, cabin and plug

Set

7.20

L030

Brass waste fitting to sink or basin complete with brass cobweb grating only

No.

5.30

Bottle Trap L031

32mm PVC bottle trap

No.

3.80

L032

38mm PVC bottle trap

No.

3.90

L033

32mm approved chromium plated bottle trap

No.

11.30

L034

38mm approved chromium plated bottle trap

No.

13.10

Accessories for Basin/Sink L035

UPVC pipe, for sink waste including elbow and bend

No.

11.00

L036

Vulcanite plug complete with chain for sink or basin

No.

3.30

L037

5mm diameter X 75mm long brass grid screw to sink

No.

1.40

L038

Delay Action Tap for Basin

No.

71.30

L039

‘Presto” No. 605 or other approved wash basin delay action tap.

No.

217.50

W.C. Suite/ Pan L040

Close-coupled white vitreous china wash down pedestal w.c. suite complete with approved rigid (heavy duty) plastic seat and cover with buffers and hinging devices, white vitreous china 9.0/4.5 litres dual action flushing cistern and all necessary fittings and connections to pipework

No.

263.60

L041

White-vitreous china close-coupled single-trap symphonic w.c. suite complete with approved rigid (heavy duty) plastic seat and cover with buffers and hinging devices, white vitreous china 9.0/4.5 litres dual action flushing cistern all necessary fittings and connections to pipework

No.

240.70

L042

Close-coupled white vitreous china wash down

No.

105.00

pedestal w.c. pan only, complete with plastic seat and cover with buffers and hinging device including trap with or without vent

SOR Page 33 Item L043

Description of Works White earthenware squat w.c. pan only, complete with trap and with/without vent including making good tile surround to match if necessary good tile surround to match if necessary and hacked up existing damage pan

Unit No.

Rate ($) 98.10

L044

White earthenware pedestal w.c. pan only complete with plastic seat and trap with or without vent

No.

105.00

Accessories for WC Suite/ Pan L045

PVC screw cap supplied and fixed for vent of w.c. squat/pedestal pan

No.

4.10

L046

Plastic w.c. seat complete with cover. (Heavy duty with any colour)

No.

34.40

L047

Plastic w.c. seat but without cover. (Heavy duty with any colour)

No.

25.60

L048

Rubber cone for joint between flush pipe and back inlet of w.c. pedestal pan.

No.

3.10

L049

PVC w.c. pan connector/ w.c. offset

No.

5.75

L050

Porcelain enamelled foottreads for squat pan including hacking up existing and make good tile surround if necessary to match existing

Pair

16.00

Toilet Roll Holder/ Dispenser L051

Jumbo plastic toilet roll dispenser

No.

25.80

L052

Surfaced mounted chromium plated toilet roll holder with plastic roller fixed or plugged to wall.

No.

14.50

L053

Surfaced mounted plastic toilet roll holder with plastic roller fixed or plugged to wall.

No.

12.70

L054

Approved plastic roller fixed in existing toilet roll holder brackets.

No.

0.90

Urinal L055

White vitreous China wall hung urinal bowl

No.

69.50

L056

White glazed urinal slabs 600mm wide X 1050mm high

No.

501.20

L057

White glazed urinal return end slab 1050mm high to match existing

No.

222.70

L058

100mm semi-circular white glazed urinal floor channels to match existing including bedding in cement mortar (1:3) and pointing in white cement.

m

181.90

L059

150mm semi-circular white glazed urinal floor channels to match existing including bedding in cement mortar (1:3) and pointing in white cement.

m

184.20

SOR Page 34 Item

Description of Works Sparge Pipe

Unit

Rate ($)

L060

15mm diameter C.P. copper sparge pipes with brackets to match existing including additional holders and all accessories.

m

13.70

L061

22mm diameter C.P. copper sparge pipes with brackets to match existing including additional holders and all accessories

m

16.40

L062

15mm diameter galvanised iron sparge pipes with brackets to match existing including additional holders and all accessories

m

12.70

L063

20mm diameter galvanised iron sparge pipes with brackets to match existing including additional holders and all accessories

m

13.10

No.

14.30

Accessories for Urinal L064

75mm brass cobweb grating to urinal. Delay Action Tap for Urinal

L065

‘Presto’ No 12 or other approval Urinal delay Action tap (Not for replacement)

No.

67.20

L066

‘Presto’ No 12 or other approval Urinal delay Action tap.

No.

68.00

Urinal Flush Valve L067

‘Presto’ No 12A or other approval concealed Urinal flush valve public toilets (not for replacement)

No.

60.30

L068

‘Presto’ No 12A or other approved concealed Urinal flush valve for public toilets

No.

61.10

L069

Urinal flush valve with/without spud

No.

62.10

L070

Urinal concealed flush valve with 16mm diameter ‘L’ shape flushing pipe, front cap cover, but without spud

No.

148.10

L071

Urinal concealed flush valve with 16mm diameter ‘L’ shape flushing pipe, front cap cover, but with spud

No.

150.40

L072

PUB approved stainless steel sensor operated flush valve complete with stainless steel outlet flush pipes to urinals including fixing and jointing to water supply and fittings as specified

No.

302.00

Cistern L073

14 litres high level bakelite cistern only, complete with chain, rubber pull and brackets

No.

99.90

L074

9/4.5 litres dual action approved high level plastic cistern complete with nylon cord; plastic pull and brackets

No.

45.00

SOR Page 35 Item L075

Description of Works 14 litres low-level earthenware cistern only, complete with flush bend, actuating level handle and cantilever brackets

Unit No.

Rate ($) 144.10

L076

14 litres low-level bakelite cistern only complete with flush bend, actuating lever handle and cantilever brackets.

No.

117.90

L077

9/4.5 litres dual action approved low level plastic cistern complete with flush bend, actuating lever handle and cantilever brackets

No.

62.80

Accessories for Cistern L078

White glazed vitreous clay cover to w.c. cistern

No.

10.20

L079

Plastic cover to w.c. cistern

No.

6.80

L080

Brass flush arm to high level cistern.

No.

9.70

L081

Brass chain and rubber pull for high level cistern

No.

6.90

L082

Brass ball-cock to w.c. cistern

No.

10.50

L083

Brass nut for flush pipe to w.c. cistern outlet connection’

No.

5.40

L084

Chromium plated lever handle to low level w.c. cistern

No.

9.70

L085

Plastic syphon unit to high level cistern

No.

15.50

L086

Plastic syphon unit to low level cistern

No.

16.80

L087

Plastic flush arm to w.c. cistern

No.

3.20

L088

Plastic flush arm holder with nylon rope to w.c. cistern

No.

3.70

L089

Plastic ball-cock complete to w.c. cistern.

No.

8.40

L090

Plastic nut for flush pipe to w.c. cistern outlet connection.

No.

4.20

L091

P.V.C. flush pipe not exceeding 2.0m long bend to high level cistern

No.

5.60

L092

P.V.C. flush pipe exceeding 2.0m but not exceeding 3.0m long bent to high level cistern.

No.

7.30

L093

40mm PVC flush pipe to low level cistern.

No.

4.30

L094

Rubber washer to w.c. cistern siphon plunger including dismantling and refixing unit.

No.

5.50

L095

13mm diameter ball valve in w.c. cistern

No.

7.50

L096

25mm diameter ball valve in w.c. cistern

No.

13.70

SOR Page 36 Item L097

Description of Works DC battery for automatic flushing cistern

Unit No.

Rate ($) 73.10

L098

Galvanised siphon hook.

No.

1.90

L099

Galvanised iron cistern chain and pull for high level cistern

No.

69.20

L100

Cast iron brackets for draining boards, sinks, basins or cisterns including cutting and pinning to walls.

No.

7.80

L101

Light gauge metal flexible inlet tube 13mm diameter to cisterns/ basins and taps complete with connectors.

No.

4.10

No.

68.60

Mirror L102

Approve 6mm thick lavatory mirror including matching screws and aluminium frame Soap Tray/ Dispenser

L103

150 X 150mm white glazed recessed type soap tray embedded in cement mortar including hacking off existing and make good tile surround to match

No.

13.50

L104

108mm X 108mm white glazed recessed type soap try embedded in cement mortar

No.

15.90

L105

20H 18-8 Type 304 stainless steel rectangular liquid soap dispenser or other approve of 1.2 litre capacity equipped with acrylic soap level window exposed surface stain-finished completed with vandal resistant mounting bracket and separate concealed wallplate.

No.

43.80

L106

Horizontal all purposed valve (Model CV-02SA) for stainless steel liquid soap dispenser constructed of chrome plated brass with Buna-N “O” ring markings with engineering plastic moving parts and push-in type valve projecting 61mm.

No.

9.90

L107

Plastic soap dispenser

No.

10.00

Shower Rose L108

Chromium plated copper shower rose.

No.

6.50

L109

Chromium plated spray shower (Telephone Type) with C.P. flexible tubing brackets and sliding rail.

No.

21.20

No.

19.20

No.

210.60

Long Bath Trap L110

Long bath trap complete with waste fittings and overflow pipes. Hand Dryer

L111

Electric automatic hand dryer

SOR Page 37 Item

Description of Works Clamp for Stainless Steel Pipe/ Ductile iron Pipe

Unit

Rate ($)

L112

25mm diameter stainless steel pipe clamp with rubber lining for emergency use on pipe burst

No.

23.70

L113

32mm diameter stainless steel pipe clamp with rubber lining for emergency use on pipe burst

No.

26.00

L114

40mm diameter stainless steel pipe clamp with rubber lining for emergency use on pipe burst

No.

28.30

L115

50mm diameter stainless steel pipe clamp with rubber lining for emergency use on pipe burst

No.

34.00

L116

100mm diameter stainless steel pipe clamp with rubber lining for emergency use on pipe burst

No.

122.80

L117

150mm diameter stainless steel pipe clamp with rubber lining for emergency use on pipe burst

No.

139.20

No.

60.00

Stainless Steel Screen L118

150 mm diameter square or round X 1.16,, thick stainless steel screen with 13mm diameter perforated holes to outlet of water main at rooftop water tanks Bin Chute Flush Pipe

L119

30mm diameter C.P. copper flush pipes including all necessary tees and brackets for each chute

No.

13.70

L120

30mm diameter galvanised steel flush pipes including all necessary tees and brackets for each chute

No.

11.00

No.

37.50

Temporary Removal of WC/ Long Bath L121

Temporary removal of vitreous china pedestal to

facilitate repair works and re-installation of existing pedestal upon completion of repair works including repositioning of flushing cistern if necessary (measured separately if such job is required) L122

Temporary removal of long bath tub to facilitate repair works and re-install the existing long bath tub upon completion of repair works including all necessary wall tiles and repositioning of piping and fittings (measured separately if such job is required)

No.

76.10

SOR Page 38 Item

Description of Works (M) BIB TAPS / STOP COCK / VALVES FOR SANITARY WORKS

Unit

Rate ($)

* Supply and fix the following sanitary fittings and accessories *(M001 M063) Stop Cock M001

13mm DZR type brass screw down stop cock

No.

11.30

M002

20mm DZR type brass screw down stop cock

No.

18.90.

M003

25mm DZR type brass screw down stop cock

No.

29.70

M004

32mm DZR type brass screw down stop cock

No.

68.60

M005

40mm DZR type brass screw down stop cock

No.

82.90

M006

50mm DZR type brass screw down stop cock

No.

113.90

M007

13mm chromium plated brass stop cock

No.

13.00

Bib Tap M008

13mm brass bib key tap with spigot nozzle including portable spindle head

No.

10.50

M009

13mm “DZR type” brass high pressure screw down bib tap with a hole drilled through the spindle

No.

13.90

M010

13mm brass bib key tap including portable spindle head

No.

9.90

M011

13mm brass bib tap with spigot nozzle and locking eye

No.

15.65

M012

13mm “DZR type” brass high pressure screw down bib tap

No.

11.50

M013

13mm chromium plated brass bib tap

No.

12.80

M014

13mm garden bib tap with spigot nozzle

No.

11.40

M015

13mm chromium plated spring loaded self-closing tap

No.

27.40

M016

13mm chromium plated pillar tap

No.

16.90

M017

15mm chromium plated pillar tap with swivel swan neck

No.

21.70

M018

15mm chromium plated brass 2-way bib-tap

No.

30.40

M019

20mm “DZR type” brass high pressure screw down bib tap

No.

14.40

M020

20mm chromium plated brass bib tap

No.

15.20

M021

20mm garden bib tap with spigot nozzle

No.

21.60

Unit No.

Rate ($) 17.90

SOR Page 39 Item M022

Description of Works 20mm chromium plated brass pillar tap to long bath Gland Nut

M023

Gland nut for 13mm stop cock/bib tap

No.

2.80

M024

Gland nut for 20mm stop cock/bib tap

No.

2.80

M025

Gland nut for 25mm stop cock/bib tap

No.

2.90

M026

Gland nut for 21mm stop cock/bib tap

No.

2.90

M027

Gland nut for 40mm stop cock/bib tap

No.

3.20

M028

Gland nut for 50mm stop cock/bib tap

No.

3.60

Rubber Washer M029

Rubber washer for 13mm to 25mm stop cock or bib tap in replacement

No.

1.30

M030

Rubber washer for 30mm to 50mm stop cock or bib tap ion replacement

No.

1.40

Gate Valve M031

13mm diameter bronze gate valve in replacement including washers, gaskets, bolts and nuts.

No.

11.60

M032

20mm diameter bronze gate valve in replacement including washers, gaskets, bolts and nuts

No.

13.90

M033

25mm diameter bronze gate valve in replacement including washers, gaskets, bolts and nuts.

No.

23.65

M034

30mm diameter bronze gate valve in replacement including washers, gaskets, bolts and nuts

No.

28.00

M035

40mm diameter bronze gate valve in replacement including washers, gaskets, bolts and nuts

No.

29.10

M036

50mm diameter bronze gate valve in replacement including washers, gaskets, bolts and nuts

No.

38.70

M037

80mm diameter bronze gate valve in replacement including washers, gaskets, bolts and nuts

No.

145.05

M038

100mm diameter bronze gate valve in replacement including washers, gaskets, bolts and nuts.

No.

290.80

M039

80mm diameter cast iron gate valve in replacement

No.

97.60

including washers, gaskets, bolts and nuts M040

100mm diameter cast iron gate valve in replacement including washers, gaskets, bolts and nuts

No.

120.40

M041

50mm diameter “DZR type” brass gate valve in replacement including washers, gaskets, bolts and nuts

No.

33.10

SOR Page 40 Item

Description of Works Ball Valve

Unit

Rate ($)

M042

40mm diameter “DZR type” brass ball valve

No.

38.90

M043

Lever stem to 50mm diameter equilibrium ball float valve

No.

13.50

No.

261.70

Sluice Valve M044

150mm diameter cast iron sluice valve with flanged ends and wheel head Valve for Dry Riser

M045

63mm diameter fire dry main landing valve (The valve shall be constructed in good gunmetal, screwed or flanged for attachment to the dry riser main and fitted with a 63mm. Instantaneous female coupling with a removable blank cap screwed by a suitable length of chain).

No.

96.00

M046

Approved dry riser inlet brass valves consisting of 4 inlets, each consisting of a 63mm instantaneous male coupling (British “B” type), a back pressure valve and protected by a cap screwed with a suitable length of chain.

No.

365.50

Accessories for Dry Riser M047

Brass chain for dry riser blank cap

No.

6.30

M048

Brass cap with chain for dry riser main

No.

20.70

M049

Gunmental hand wheel for dry riser landing valve marked with ‘OPEN’ and ‘SHUT’ directions including all necessary nuts and washers.

No.

15.20

M050

19/25mm diameter jet spray nozzle with ON/OFF handle

No.

27.40

M051

Approved automatic air release valve 25mm for dry riser main

No.

22.20

M052

Approved canvas /nylon belt with key-alike padlocks for strap locking handwheels in closed position

No.

6.80

W.C. Flush Valve

M053

Exposed water closet flush valve with 240 X 408mm ‘L’ flush pipe, vacuum breaker and stop valve for back inlet water closet

No.

148.10

M054

Exposed water closet flush valve with 280mm long supply pipe, vacuum breaker and stop valve for top inlet water closet bowl

No.

148.10

M055

Water closet water-saving flush valve with 470 X 320mm long ‘T’ flush pipe, vacuum breaker and stop valve

No.

153.90

SOR Page 41 Item M056

Description of Works Water closet water-saving flush valve with 280mm long flush pipe, vacuum breaker and stop valve

Unit No.

Rate ($) 326.40

M057

Water closet concealed flush vale with flushing pipe and 32mm diameter elbow coupling

No.

148.10

M058

Water closet water-saving concealed flush valve with flushing pipe and 32mm diameter elbow coupling

No.

217.10

M059

PUB approved stainless steel sensor operated flush valve complete with stainless steel outlet flush pipes to water closets including fixing and jointing to water supply and fittings as specified

No.

426.70

No.

9.10

No.

5.60

Stop Valve for Basin/ Cistern M060

Miniature stop valves for basin and cistern Flow Regulator

M061

15mm diameter approved constant flow regulator of 12 litres per minute Rubber Hose

M062

19mm non-link, 2 braided rubber hose

m

7.50

M063

25mm non-link, 2 braided rubber hose

m

7.50

SOR Page 42 Item

Description of Works (N) TRAP AND GRATING

Unit

Rate ($)

* Supply and fix the following sanitary fittings and accessorises *(N001 N052) Floor Trap N001

150mm salt-glazed stoneware gulley complete with grating, 100mm outgo and concrete surround of minimum 100mm thick including hacking existing damaged gulley and jointing to existing pipes

No.

53.00

N002

Cast iron deep seal floor trap complete with hinged grating cast iron hopper and with vertical side or back inlets and 75mm outgo pipe including hacking existing damaged trap and jointing to existing pipe.

No.

77.50

N003

150mm cast iron hopper connecting piece not exceeding 300mm long including hacking existing hopper and all necessary jointing to pipe.

No.

13.20

N004

100mm diameter cast iron floor trap or floor waste with hinged grating, hopper and 75mm outgo and concrete surround (at ground floor slab) including hacking to remove existing damaged trap/waste and jointing to pipe.

No.

54.20

N005

150mm diameter cast iron floor trap with hinged grating, hopper and 100mm diameter outgo and concrete surround (at ground floor slab) including hacking to remove existing damage trap and jointing to pipe.

No.

71.00

Cast Iron Grating N006

50mm diameter cast iron gratings including embedding in cement mortar

No.

1.60

N007

75mm diameter cast iron gratings including embedding in cement mortar

No.

2.00

N008

100mm diameter cast iron gratings including embedding in cement mortar

No.

2.50

N009

150mm diameter cast iron gratings including embedding in cement mortar

No.

2.50

N010

150mm Chromium plated hinged grating for floor trap

No.

7.10

N011

8mm thick 150mm cast iron square hinged/frame grating to apron gulley

No.

4.70

N012

6mm thick 150mm square plastic with/without perforated grating with hinge/frame including embedding in cement mortar.

No.

4.60

N013

6mm thick 150mm square cast iron with/without perforated grating with hinges/frame including embedding in cement mortar.

No.

10.40

SOR Page 43 Item N014

Description of Works 2mm thick 150mm galvanised steel square hinged with/without perforated grating for apron gulley including embedding in cement mortar.

Unit No.

Rate ($) 7.60

Plastic Grating N015

50mm diameter plastic gratings including embedding in cement mortar

No.

1.00

N016

75mm diameter plastic gratings including embedding in cement mortar

No.

1.30

N017

100mm diameter plastic gratings including embedding in cement mortar

No.

1.80

N018

150mm diameter plastic gratings including embedding in cement mortar

No.

2.00

N019

150mm square with 100mm diameter plastic hinged grating for floor trap including setting in concrete.

No.

3.20

Dome-Shaped Grating N020

75mm diameter galvanised steel spherical domeshaped grating 2.0mm thick to rainwater down pipe outlet including hacking and setting with cement mortar

No.

5.20

N021

100mm diameter galvanised steel spherical domeshaped grating 2.0mm thick to rainwater down pipe outlet including hacking and setting with cement mortar

No.

7.70

N022

150mm diameter cast iron dome-shaped hinged grating

No.

29.20

Vertical Grating N023

100mm diameter vertical cast iron grating with 115mm outgo for rainwater down pipe outlet including hacking and setting in cement mortar

No.

40.80

N024

Purpose made mild steel vertical grating to 75mm diameter rainwater down pipe outlet including embedding in floor slab and makes good all disturbed area.

No.

18.65

Cast Iron Dome Grating N025

75mm diameter cast iron dome grating including embedding in cement mortar

No.

14.90

N026

100mm diameter cast iron dome grating including embedding in cement mortar

No.

16.20

N027

150mm diameter cast iron dome grating including

No,

20.40

embedding in cement mortar

SOR Page 44 Item

Description of Works Strainer

Unit

Rate ($)

N028

Purpose made perforated 18G aluminium strainer for street gulley trap excluding cast iron grating (Not exceeding 300mm diameter)

No.

84.00

N029

Purpose made perforated 18G aluminium strainer for street gulley trap excluding cast iron grating (Exceeding 300mm but not exceeding 450mm diameter)

No.

92.10

N030

Cast iron strainer for interceptor trap, rectangle/square type not exceeding 0.72m2

No.

86.70

N031

100mm diameter ductile iron ‘Y’ – pattern trap including flanges and cutting removing existing pipe etc

No.

245.30

N032

150mm plastic slot grating including embedding in cement mortar

No.

4.95

Anti-Mosquito Device N033

Anti mosquito device (98mm) with body; filter; cover and gully trap grating

No.

5.60

N034

Anti-mosquito device (98mm) with body; filter and cover only

No.

2.40

N035

Anti-mosquito device (counter weight type) without grating

SET

2.85

Screw on Grating N036

150mm UPVC screw on floor trap grating

SET.

3.40

N037

Ditto but including filter

No.

5.70

SET

10.65

No.

23.00

Heavy Duty Grating N038

150mm square or round UPVC heavy duty floor trap grating Alloy Steel Floor Trap

N039

150mm chrome plated alloy steel floor trap grating Screw Dome Grating

N040

75mm diameter UPVC dome grating with square base

No.

3.75

N041

100mm diameter UPVC dome grating with square base

No.

4.95

N042

150mm diameter UPVC dome grating with square

No.

5.40

base

SOR Page 45 Item

Description of Works Balcony Grating

Unit

Rate ($)

N043

50mm diameter UPVC Balcony/Roof grating outlet square base (Dome or flat type) for SS 213 pipes including removal of exiting damage PVC/CI outlet pipe, preparing entry for new outlet and make good all works disturbed

No.

5.30

N044

Ditto but 50mm diameter

No.

11.75

N045

Ditto but 100mm diameter

No.

17.55

N046

Ditto but 150mm diameter

No.

20.30

N047

50mm, diameter UPVC Balcony/Roof grating outlet square base (Dome or Flat type) for SS 141 pipes including removal of existing damage UPVC / CI outlet pipe, preparing entry for new outlet pipe, preparing entry for new outlet and make good all works disturbed

No

5.45

N048

Ditto but 80mm diameter

No.

12.05

N049

Ditto but 100mm diameter

No.

18.90

N050

Ditto but 150mm diameter

No.

21.95

Auto Floating Ball Grating N051

Auto floating ball cover fitting c/w lightweight PVC ball

No.

7.50

N052

UPVC screw-down domical grating to top of 200mm diameter pipe complete with 240 X 240mm square body.

No.

54.90

SOR Page 46 Item

Description of Works (P) SUPPLY AND INSTALLATION/REPAIRS AND REINSTAEMENT WORKS FOR SANITARY

Unit

Rate ($)

Repair to Cast Iron Soil/Waste Pipes P001

Re-caulk joints of 75mm diameter cast iron pipes soil or waste pipes including raking out and providing additional molten lead and spun yarn if required.

No.

5.80

P002

Re-caulk joint of 100mm diameter cast iron pipes soil or waste pipes including raking out and providing additional molten lead and spun yarn if required.

No.

7.20

P003

Re-caulk joint of 150mm diameter cast iron pipes soil or waste pipes including raking out and providing additional molten lead and spun yarn if required

No.

8.50

Repair to Cast Iron Rising Main Pipes P004

Re-caulk joints of 100mm diameter cast iron rising main pipe including raking out and providing additional spun yarn and molten lead if required in upright position

No.

7.30

P005

Re-caulk joints of 100mm diameter cast iron rising main pipe on level ground including raking out and providing additional spun yarn and molten lead if required.

No.

6.60

P006

Re-caulk joints of 150mm diameter cast iron rising main pipe including raking out and providing additional spun yarn and molten lead if required in upright position.

No.

7.80

P007

Re-caulk joints of 150mm diameter cast iron rising main pipe on level ground including raking out and providing additional spun yarn and molten lead if required.

No.

7.30

P008

Cut 100mm diameter cast iron rising mains and jointing with Gilbault coupling

No.

35.30

P009

Cut 150mm diameter cast iron rising mains and jointing with Gilbault coupling

No.

45.70

Job

2.20

No.

2.60

Repair to Cleaning Eye P010

Repair leaking, cleaning eyes/ oval shaped inspection covers of C.I. soil and waste pipes of 75mm and above in diameter Repair to Services Pipes

P011

Repair leaking joints of galvanised service pipes not exceeding 25mm diameter.

P012

Repair leaking joints of galvanised service pipes exceeding 25mm diameter but not exceeding 50mm diameter

No.

3.20

SOR Page 47 Item P013

Description of Works Repair leaking joints of galvanised service pipes exceeding 50mm diameter but not exceeding 100mm diameter

Unit No.

Rate ($) 5.10

P014

Repair leaking joints of galvanised service pipes exceeding 100mm diameter

No.

7.70

P015

Cut off existing galvanised pipes, threads end and prepare for connection to new pipes.

No.

3.90

P016

Take down service pipes not exceeding 25mm diameter for cleaning and rodding and refixing including making good joints, and all works disturbed.

m

3.60

P017

Take down service pipes exceeding 25mm diameter but not exceeding 50mm for cleaning and rodding and refixing including making good joints, and all works disturbed.

m

4.20

P018

Take down service pipes exceeding 50mm diameter for cleaning and rodding and refixing including making good joints, and all works disturbed.

m

4.90

P019

Bore holes in water services pipes for use as bin chute sparge pipes at 50mm centre to centre (per chute)

Job

4.40

Job

4.80

Repair to Copper Inlet Pipe P020

Take down copper inlet pipe to w.c. cistern for clearing and roddng including refixing to position and make good work disturbed. Repair to WC

P021

Repair defective w.c. cistern including renewing washer

No.

8.70

P022

Hack hole through wall or floor slabs not exceeding 150mm thick to form chase for entry of water service pipes (measured separately if such job is required)

Job

14.00

P023

Break up concrete stooling and footrest of w.c., reconcrete with 1:2:4 (Grade 20) reinforced concrete including trowelling smooth to surface with waterproof of cement mortar (1:3) (replacement of w.c. measured separately)

Job

21.60

Clearing Obstructions on Gully Traps/ Pipes/ Etc P024

Clear obstructions in traps of basins or sink and water meter pipes including cleaning up areas an completion

Choke

3.30

P025

Clear obstruction in floor traps, gulley traps and urinal traps.

Choke

2.30

P026

Clear obstructions in w.c. pan

Choke

6.60

P027

Clear obstructions in soil and waste stack

Choke

7.40

SOR Page 48 Item P028

Description of Works Clear obstructions or for flushing the sullage water or rainwater down pipes right through to sumps or house drains

Unit Choke

Rate ($) 3.70

P029

Manual clearing of chokes by cleaning rods in sewer lines (Rate involves 2 adjacent manholes and the connecting lines).

Job

16.30

P030

Clear obstructions in waste water inceptor trap.

Choke

7.40

P031

Clear obstruction in grease gulley trap

Job

7.40

P032

Clear obstruction in traps of street gulleys including removal of debris from strainer.

Job

4.10

P033

Flush and remove oil wastes in grease lines in industrial workshop

m

2.60

P034

Pump up and remove oil waste from oil interceptors in industrial workshops

No.

19.20

P035

Flush the 100mm diameter ductile iron ‘Y’ pattern trap

No.

3.30

P036

Clear waste and sludge from oil interceptors in industrial estates collected in metal drum (209 litres/46 gallons) and cart away to ENV’s dumping ground in accordance with ENV’s requirement and all necessary expenditure/fees.

Drum

39.90

No.

17.90

Repair to Gate Valve P037

Repair 80mm to 100mm cast iron gate valve leakage including renewing gaskets Refix Sanitary Accessories

P038

Refix loose sink plug

No.

0.80

P039

Refix loose sanitary accessories such as mirrors, brackets, etc.

Job

2.40

P040

Adjust stop cocks to tilt towards any direction specified including making good any damaged or affected piping work.

Job

2.40

P041

Clean white glazed w.c. pans or other white glazed sanitary fittings to a satisfactory finish free from stain.

Job

5.20

Job

4.70

Flushing of Downfeed Pipe P042

Flush water downfeed pipe at common corridor including removal of residue and cleaning up areas on completion. Repair to Stainless Steel Pipe

P043

Repair leaking joints of stainless steel pipe not exceeding 42mm diameter.

No.

5.00

SOR Page 49 Item P044

Description of Works Repair leaking joints of stainless steel pipe not exceeding 75mm diameter

Unit No.

Rate ($) 5.10

No.

5.20

No.

16.90

Repair to UPVC Pipes P045

Repair leaking joints of UPVC pipe from 50mm diameter to 150mm diameter Repair to Dry Riser

P046

Repair leaking joint of dry raiser pipe to comply with Building Control and Fire Brigade regulation and tested. Locking Device

P047

Electro galvanised steel locking device for Civil Defence tap, 180 X 110 X 150mm for taps in void decks with all accessories.

No.

24.40

P048

Electro galvanised steel locking device for Civil Defence tap, 200 X 170 X 195mm for taps in void decks with all accessories.

No.

27.20

P049

2mm thick galvanised iron locking device of approved box or cylindrical pattern for staircase taps, bin chute stopcock etc complete with chain including all necessary welding.

No.

15.50

P050

Electro galvanised steel locking device 150mm X 150mm X 150mm for taps in void decks and staircases with and including 100mm heavy duty internal butt hinges, 25mm groove for insertion of pie and two coats of oven baked spray paint and approved cam lock with a key-alike system.

No.

24.00

P051

Modification of existing 200 X 170 X 195mm electrogalvanised steel box with self locking device (‘Abloy’ furniture lock).

No.

56.70

P052

200 X 200 X 150mm 16 gauge mild steel box with electro-galvanised coated with 1 coat of epoxy baked powder coated paint c/w locking device.

No.

40.90

Job

24.75

Job

16.60

Per Unit

1.40

Repair to Sensor Flushing System P053

Repair automatic sensor flushing system Repair to Coin Operated Water Dispenser

P054

Repair defective coin operated water dispenser Miscellaneous Repairs

P055

Deposit sand granules (mosquito insecticide) in water seal in w.c. pans, gulley traps and w.c.

cisterns, etc, in one vacant flat.

SOR Page 50 Item P056

Description of Works Break through roof slab with electric drill to form opening for entry of water service pipes and making good all work disturbed including secondary roofing work an completion of pipe installation to the entire satisfaction of the roofing specialist (measured separately if such job is required)

Unit Opening

Rate ($) 17.00

P057

Seal up sand holes in cast iron pipes with metallic epoxy resin as per manufacturer’s instruction including touching up paint to match existing

No.

5.10

P058

Plug off existing unused tap

No.

4.60

P059

Clean urinal range, remove existing cement pointing between slab/channels etc and repaint with white cement.

Job

21.10

P060

Supply labour and equipment for locating leakage test in underground pipe.

Test

161.00

P061

Repair leaking tap at wash area

No.

4.10

P062

Repair leaking cast iron pipe at joint of UPVC pipe exceeding 75mm but not exceeding 150mm diameter

Joint

6.40

P063

Replace lock only to tap box of refuse chute flushing system & civil defence tap to match existing.

No.

13.80

P064

Break up existing long bath wall to form opening of size equivalent to 4 nos. of wall tiles, complete with precast door, finish with glazed wall tiles to match existing including carting away of debris.

Job

41.20

P065

Break up displaced stool support or water mains and provide new 305mm X 305mm brick stool support not exceeding 380mm high including rendering sides and haunching top in cement mortar (1:3)

No.

11.20

P066

Repair leak in concrete surround of gulley trap, cast iron soil pipes, etc. with waterproofed cement mortar.

Job

3.60

P067

Repair in concrete surround of squat pan with waterproofed cement mortar.

Job

4.10

P068

Repair leak in concrete surround of squat pan including making good tiled or terrazzo floor finish to match.

Job

8.20

P069

Hack out existing point at joint between sink and wall and repaint in white cement.

Job

3.00

P070

Hack out existing pointing at joint between long bath and wall and repaint in white cement.

Job

9.90

P071

Form 75mm high cement surround at base of w.c. cistern flush-pipe and squat pan joint to cure leak.

Job

2.90

SOR Page 51 Item

Description of Works (Q) CLEANING AND DESILTING WITH ELECTROMECHANICAL EQUIPMENT

Unit

Rate ($)

Q001

Clear, flush with water, clean, including scrape hardened oil sludge, debris etc, off sewer lines using high pressure water jetting and electro-mechanical equipment with minimum discharge pressure of 4000 PSI

m

0.70

Q002

Clear, flush with water, clean, including scrape hardened oil sludge, debris etc, off sewer lines using high pressure water jetting and electro-mechanical equipment with minimum discharge pressure of 4000 PSI and vacuum cleaning equipment (Including main and branch half round channels within inspection chambers)

Job

3.30

Q003

Clear, flush with water, clean, including scrape hardened oil sludge, debris, etc off street gulleys and strainers

Job

5.10

Q004

Clear, flush with water, clean, including scrape hardened oil sludge, debris etc, off grease trap/ interceptor using high pressure water jetting and electro-mechanical equipment with minimum discharge pressure of 4000 PSI including vacuum cleaning of solids and semi solids

Job

134.10

Q005

Mechanised clearing of obstructions in sewer lines/ manholes by high pressure water pressure water jetting equipment and/ or other electro-mechanical sewer cleaning equipment with minimum discharge pressure of 4000 PSI (Rate involves 2 adjacent manholes and the connection line)

Job

18.60

SOR Page 52 Item

Description of Works (R) WATER TANK REPAIRS, CLEANING PAINTING WORK

Unit

Rate ($)

Supply and Installation/ Repairs and Reinstatement Works for Water Tank R001

Patch up holes in tank walls/ bottoms/ covers by welding new pieces of plates (including the cost of use, transportation and removal of welding equipment).

No.

30.40

R002

Repair leaking joint of water storage tank with approved non-toxic sealing compound including tightening of all blots and nuts.

m

4.50

R003

100mm diameter galvanised steel spring clip with nylon nettings cover at outlet of overflow pipe.

No.

3.40

R004

New nylon mosquito mesh of approved quality to open tanks with approved non-toxic sealing compound

m2

2.00

R005

New nylon mosquito mesh of approved quality to 150mm square or round grating with approved nontoxic sealing compound

No.

1.20

R006

0.6mm thick corrugated colour band galvanised steel cover

m2

47.90

R007

Seal up gaps along edges between covers and tanks with new nylon mosquito mesh of approved quality with approved non-toxic sealing compound

m2

1.10

R008

75 X 75 X 6mm thick angle iron bracing / stay to water tank (including bolts and nuts etc).

m

7.10

R009

Dismantle and remove of existing bracing/ stay off site.

m

1.50

R010

Galvanised bolts and nuts to water tanks

No.

1.10

R011

Repair of leaky joints of link pipe jointing to water storage tanks including necessary gaskets, sealing compound etc.

Joint

14.40

R012

Rolled steel hoists for support of tanks including bolts, fixing and painting

Kg

1.30

R013

Approved inspection cover to mild steel water tank to match existing

No.

34.60

R014

108 X 108mm approved white glazed wall tiles including rounded ages tiles etc and cement screed to the concrete water tank

m2

34.60

R015

Form an opening through top/side/bottom of water

No.

26.20

tank for the entry of pipe not exceeding 150mm diameter including connection of pipe and drilling holes for blots.

SOR Page 53 Item R016

Description of Works Dismantle bulging water tank panel and refix to proper shape including flushing out water (provision of additional angle steel bracings/ stays measured separately).

Unit Panel

Rate ($) 23.00

R017

100mm galvanised iron Dam nut complete with washer, etc. to water tank

No.

8.40

R018

Refix fallen off water tank cover. (Provision of additional angle supports, blots and nuts measured separately)

m2

5.40

R019

Repair leakage at jamb nut including flushing out water if necessary and tightening jamb nut.

No.

15.90

R020

Dismantle and remove from site existing damaged inspection cover including the 150mm high four-sided galvanised steel boxing to the access hole and replace with 0.559mm thick galvanised steel cover overall size 490 X 490mm including boxing up the access hole with 150mm high X 0.559 thick galvanised steel including pop-riveting

Cover

50.90

R021

Electrode-holder clamp for water tanks

No.

23.50

R022

100mm diameter PVC cap with 100mm diameter (UPVC) bend (any angles )or elbow (SS 213) plain and a 100mm diameter testing openings (F&F) including removal of existing nylon netting and drill holes of different sizes to PVC cap and providing on allan type screw.

Job

27.00

Flushing, Cleaning and Sterilization of Water Tank R023

Prepare, sand and remove rust, stains and other sediments from internal sides and bottom of tanks, flush and clean surfaces, including bracing to stainless steel water tank

m2

0.40

R024

Prepare, remove all rust, stains and other sediments from internal sides and bottom of tanks, flush and clean surfaces to FRP/GRP or Reinforced concrete storage or suction tanks, including flushing and refilling tanks upon completion and including flushing and refilling tanks upon completion

m2

0.30

R025

Flush suction/storage tanks and refilling with clean water upon completion (this item is used where washing of tank is not required

No. of Tank

3.30

R026

Sterilise Mild Steel/ FRP/ Polyethylene Lined/

m3

0.30

Stainless Steel/ Concrete Water Storage Tanks to overflow level. R027

Test of water samples including transportation from site and submission of test reports.

No.

48.70

SOR Page 54 Item R028

Description of Works Prepare; remove all stains and sediments from Internal sides and bottom of mild steel tank, flush and clean surfaces including bracing to mild steel tanks. (Note: only when painting is Not required)

Unit m2

Rate ($) 0.70

R029

Clean and remove rust stains from external surface of stainless steel water tanks

m2

0.35

R030

Flush steel strainer located after PUB Bulk Meter including dismantling and refixing

No.

6.10

Painting Works for Water Tanks R031

Prepare, scrap, remove rust and incrustations and other sediments form internal sides and bottom of mild steel tanks, including removal of existing mosquito netting (if any), flush and clean surfaces, bracing, and mop up with cloth to dry to receive new painting (painting measured separately)

m2

0.60

R032

Paint internal surface of mild steel water tanks including bracing with one coat of rust converter (Water Base) (Surface preparation measured separately)

m2

3.00

R033

Paint internal surface of mild steel water tanks including bracing with two finishing coats (Water Base) (Surface preparation measured separately)

m2

5.60

R034

Paint internal surface of mild steel water tanks including bracing with two finishing coats (Epoxy Base) (Surface preparation measured separately)

m2

5.80

R035

Paint external surface of mild steel water tanks including bracing with one coat of rust converter (Water Base) (Surface preparation measured separately)

m2

2.80

R036

Paint external surface of mild steel water tanks including bracing with one coat of primer (Epoxy Base) (Surface preparation measured separately)

m2

4.10

R037

Paint external surface of mild steel water tanks including bracing with one finishing coat (Water Base) (Surface preparation measured separately)

m2

3.20

R038

Paint external surface of mild steel water tanks including bracing with one finishing coat (Epoxy Base) (Surface preparation measured separately)

m2

5.50

R039

Engage Professional Engineer to inspect and certify the water installation were fit and safe to use, properly maintained and free form leakage. (This rate shall not be subject to percentage adjustment stated in the Form of Tender)

Block

500.00

SOR Page 55 Item

Description of Works (S) MATERIAL SUPPLY

Unit

Rate ($)

* The following items are for supply of materials only. (Works performed by the standby plumber as specified) 8(S001 S018) S001

13mm diameter light gauge metal flexible inlet tube to cistern/basins and taps complete with connectors.

No.

3.00

S002

13mm rubber washer to tap and stop cock.

No.

0.40

S003

Coupling washer to meter pipe connector.

No.

0.30

S004

Ball valve washer to w.c. cistern

No.

0.50

S005

Rubber washer to w.c. cistern siphon plunger.

No.

0.50

S006

13mm diameter copper ring to service pipe.

No.

0.50

S007

20mm diameter copper ring to service pipe.

No.

060

S008

28mm diameter copper ring to service pipe.

No.

0.80

S009

35mm diameter copper ring to service pipe.

No.

1.10

S010

42mm diameter copper ring to service pipe.

No.

1.30

S011

54mm diameter copper ring to service pipe.

No.

1.50

S012

13mm diameter ‘DZR type’ brass stop cock.

No.

8.40

S013

13mm diameter ‘DZR type’ high pressure brass screw down bib tap

No.

8.40

S014

13mm diameter copper piping 300mm long with connectors at both ends for fittings

No.

3.30

S015

2mm thick 75mm diameter galvanised steel; spherical dome-shaped grating

No.

1.75

S016

2mm thick 150mm diameter galvanised steel square hinged with/without perforated grating for apron gully

No.

3.45

S017

150mm UPVC screw floor trap grating

No.

7.50

S018

13mm brass bib key tap including portable spindle head

No.

7.50

SOR Page 56 Item

Description of Works (T) MISCELLANEOUS

Unit

Rate ($)

T001

13mm chromium plated long handle tap

No.

47.80

T002

Deck mounted stainless steel liquid soap dispenser

No.

47.80

T003

Take out existing ball valve in tank and remove off site

No.

25.50

T004

Supply and install 40mm PUB approved water meter (flanged type)

No.

332.50

T005

Supply and install 50mm PUB approved water meter (flanged type)

No.

342.00

T006

400mm diameter cooper ball flat in replacement in water tank

No.

93.20

T007

Fibreglass water storage tank not exceeding 1000 litres nominal capacity, supported by 3 pieces 38 X 75mm twice creosoted timber battens and cover of flat shape with beaded edges lined down and with all edges bolted and jointed with stainless steel bolts

No.

313.50

T008

Fibreglass water storage tank not exceeding 2000 litres nominal capacity, supported by 3 pieces 38 X 75mm twice creosoted timber battens and cover of flat shape with beaded edges lined down and with all edges bolted and jointed with stainless steel bolts

No.

332.50

T009

Fibreglass water storage tank not exceeding 3000 litres nominal capacity, supported by 3 pieces 38 X 75mm twice creosoted timber battens and cover of flat shape with beaded edges lined down and with all edges bolted and jointed with stainless steel bolts

No.

427.50

T010

Fibreglass water storage tank not exceeding 4000 litres nominal capacity, supported by 3 pieces 38 X 75mm twice creosoted timber battens and cover of flat shape with beaded edges lined down and with all edges bolted and jointed with stainless steel bolts

No.

323.00

T011

Take out existing basin or sink of any size including brackets, disconnect pipes, etc and set aside for reuse and make good all work disturbed

No.

12.75

T012

Take out existing basin or sink of any size including brackets, disconnect pipes, etc and set aside for reuse and make good all work disturbed and remove to store or off site.

No.

16.55

T013

Refix existing basin or sink in new position including cutting and pinning brackets, diverting, altering and adjusting water services, waste pipes, etc and make good all work disturbed including additional piping required

No.

31.55

T014

Add for each addition 1.50m or part thereof

No.

16.35

SOR Page 57 Item T015

Description of Works Labour only fixing lavatory basin or sink complete including cutting and pinning brackets, making all connections and all additional piping required

Unit No.

Rate ($) 21.75

T016

White glazed modesty board

Piece

94.45

T017

Urinal bowl

No.

56.55

SOR Page 58 Item

Description of Works (C) SUPPLY AND FIX THE FOLLOWING MATERIAL FOR URINAL SENSOR FLUSH VALVE IN REPLACEMENT *(C001 C022)

Unit

Rate ($)

U001

Flush valve cap

No.

26.40

U002

Flush valve body

No.

41.40

U003

Stopcock handle

No.

27.30

U004

Cap

No.

13.20

U005

Outlet piping nut

No.

13.20

U006

Flush valve cap rubber washer

No.

13.20

U007

Adaptor

No.

18.20

U008

Adaptor rubber washer

No.

9.00

U009

Outlets piping washer

No.

9.00

U010

Pixton

No.

32.30

U011

Sensor plate pivot rod

No.

38.20

U012

Cover frame c/w screws

No.

48.20

U013

Casing c/w front cover, back cover & screws

No.

64.60

U014

Cam lock for sensor plate

No.

18.20

U015

Sensor assy e/w studs & nuts

No.

100.00

U016

Solenoid assy c/w valve coil, plug, rubber, washer, screw (E-Ring)

No.

81.40

U017

Elbow (90 degree street, T-Elbow)

No.

13.20

U018

Elbow M4 male stud tubing fitting

No.

13.20

U019

Solenoid brackets c/w screws

No.

31.40

U020

AC adaptor assy c/w earth cable, connector & screws

No.

86.40

U021

4mm to 6mm PU tubing

No.

5.00

U022

Push button assy c/w cap wit Hexagonal nut & switch

No.

34.20

SSOR Page 1 SUPPLEMENTARY SCHEDULE OF RATES Item

Description of Works (D) SUPPLY & FIX THE FOLLOWINF MATERIAL FOE WATER CLOSET (WC) FLUSH VALVE IN REPLACEMENT *(D001 D031)

Unit

Rate ($)

V001

Stopcock handle

No.

117.30

V002

‘O’ ring

No.

9.00

V003

Stopcock cap

No.

13.20

V004

Stopcock cap ‘O’ ring

No.

9.00

V005

Stopcock seal

No.

13.00

V006

Check valve

No.

33.00

V007

Stopcock valve rubber washer

No.

9.00

V008

Stopcock assy c/w handle, ‘O’ ring stopcock cap, ‘O’ ring, seal check valve and rubber washer

No.

124.60

V009

Flush valve cap

No.

26.40

V010

Check valve rubber washer

No.

9.00

V011

Pixton

No.

71.40

V012

Flush valve ‘O’ ring

No

9.00

V013

Flush adaptor

No.

18.20

V014

Flush valve handle cap

No.

18.20

V015

Flush valve assy (Body, 101 ring, adaptor and handle cap

No.

56.40

V016

Vacuum breaker rubber washer

No.

9.00

V017

Piping rubber washer

No.

9.00

V018

Outlet piping nut

No

9.00

V019

Vacuum breaker assy c/w rubber washer outlet piping rubber washer & outlet piping nut

No.

56.40

V020

Sensor Plate c/w studs and nuts

No.

32.10

V021

Cover frame c/w screws and magnet

No.

45.65

V022

Casing

No.

34.20

V023

Solenoid assy c/w valve, coil, plug, rubber washer, screw & E-ring

No.

94.20

V024

Elbow Adaptor (90 degree street, T-Elbow)

No.

13.20

V025

Elbow , tubing fitting

No.

13.20

V026

4mm to 6mm tubing

No

5.00

V027

AC adaptor with controller board assy c/w earth wire, connector & screws

No.

74.60

V028

Sensor assy c/w studs and nuts

No.

100.00

V029

Push button assy c/w, cap nut, hexagonal nut & switch

No.

34.20

V030

Cam lock for sensor plate

No.

18.20

V031

Batteries pack for battery-operated sensor (Rigel)

No.

35.00

V032

Supply and fix sink mixer

No.

107.60

V033

Supply and fix long bath mixer

No.

176.60

V034

Supply and fix wall-mounted shower mixer

No.

182.40

V035

Supply and fix 15mm chromium plated brass 2-way bib tap (lever type) including all necessary accessories for fixing and jointing to pipe works

No.

73.10

V036

13mm diameter blots, nuts and washers for flange joint or outer fitting

No.

2.00

V037

17mm wide punched steel for hanging cast iron pipe etc (Band not exceeding 1.0 meter long)

No.

6.20