Otis TCB Svt
Short Description
Otis TCB board service tool manual...
Description
OTIS
FIELD COMPONENT MANUAL
Part:
4 - AA3
No.:
GBA 26800BA IV
Vintage: 01 / 1
Central & East Europe Area
FOD BERLIN
Service Tool Manual
Page:
1/ 35
TCB
Date:
17-Aug-2009
TCB Service Tool Manual
Authorization Date D1:
29-Feb-2000
Running on PCB:
GAA 26800 BA
Software Version:
GAA 30084 AAA
Document Revision : Date 03-Jul-2000
Author G. Priebe
Page 1 - 35
Comment Original Document
Copyright 2009, OTIS GmbH & Co. OHG Berlin. No part of this document may be copied or reproduced in any form or by any means without the prior written consent of OTIS.
OTIS
FIELD COMPONENT MANUAL
4 - AA3
No.:
GBA 26800BA IV
Vintage: 01 / 1
Central & East Europe Area
FOD BERLIN
Part:
Service Tool Manual
Page:
2/ 35
TCB
Date:
17-Aug-2009
Table of Contents 1
Introduction .............................................................................................3
2
Tree Structure..........................................................................................3
3
TCB Menu System ...................................................................................3 3.1 Overview ................................................................................................................... 3 3.2 Menu System ............................................................................................................ 4 3.2.1 System Path .......................................................................................................... 4 3.2.2 Tools Path ............................................................................................................. 5 3.2.3 Short Keys S4 – S9 ............................................................................................... 6 3.3 System – Menu ......................................................................................................... 8 3.3.1 Status – Menu ( ) .............................................................................. 8 3.3.2 TEST - Functions ( ) ...................................................................... 12 3.3.3 SETUP –Function ( ) ...................................................................... 17 3.4 TOOLS – Function ( ) ................................................................................. 30 3.4.1 Search-IO – Function ( ) ................................................................. 31 3.4.2 Erase-IO – Function ( ) ................................................................... 32 3.4.3 Setup Install – Function ( ) .............................................................. 32 3.4.4 Setup Door – Function ( ) ............................................................... 33 3.4.5 Operate Memory ( ) ........................................................................ 33
OTIS
FIELD COMPONENT MANUAL
1
4 - AA3
No.:
GBA 26800BA IV
Vintage: 01 / 1
Central & East Europe Area
FOD BERLIN
Part:
Service Tool Manual
Page:
3/ 35
TCB
Date:
17-Aug-2009
Introduction
The Service Tool is a pocket terminal that lets you control all elevator functions:
Monitoring of software states, system inputs and outputs and system messages Setup of installation parameters Use of software tools.
All Service Tool functions are organized under a Tree-Structure. The access of each function is controlled by the TCB-Menu System which makes convenient work with the Service Tool possible. The Service Tool Manual describes the TCB-Menu System and the single Service Tool functions.
2
Tree Structure
All Service Tool functions are organized under the Tree-Structure which you can see below. It is divided in a SYSTEM path, where you have access to the main Service Tool functions STATUS (system monitoring) SETUP (setup of system environment) and in a TOOL path. The TOOLS path contains the Service Tool functions which supports installation and maintenance of the elevator.
3
TCB Menu System
3.1
Overview
The Menu System allows you to access the single Service Tool functions if you choose the right path through the Tree Structure by pressing the correspondingly key (number 1,2,...8). If there is only one number to choose, you can call the function also with the Shift key ”ENTER”. You can toggle between the different menus using the ”GOON” or ”GOBACK” key if the ”>” character indicates a hidden menu. The ”CLEAR” key lets you jump one step back. If you want to jump back to one the three Main Level of the architecture (MONITOR, FUNCTION or SET) you can do it with the ”M”, ”F” or ”S” Main Level Key.
OTIS
FIELD COMPONENT MANUAL
FOD BERLIN
3.2
Menu System
3.2.1
System Path
No.:
GBA 26800BA IV
Service Tool Manual
Page:
4/ 35
TCB
Date:
17-Aug-2009
TCB – Menu
M 1
2 TOOLS – Menu
(8)
SYSTEM - Menu
S
4 - AA3
Vintage: 01 / 1
Central & East Europe Area
F
Part:
1
2
STATUS – Menu
(8)
(see next page )
3 TEST – Menu
1
Calls
(9)
1
2
Inputs
(10)
2
3
Outputs
(11)
3
Part
(15)
4
Group
(11)
4
RSL
5
ICSS
(11)
5
Selftest
6
Cmd
(12)
Events
SETUP – Menu
(12) (13)
1
Diagnosis (14)
INSTALL – Menu 1
System
2
OCSS
(15)
3
Group
(16)
4
Drive
5
Doors
6
Pos. Ref.
7
Service
8
Emerg.
9
Security
goon
Page number
Test
RSL
3
ALLOWED – Menu (20)
Menu System
(13)
(18)
2
Legend: Service Tool Key 1
Function
(17)
(19)
1
Enabled
2
Cut Call
3
Card Rd
4
Pos
(23)
5
DCS - Run
(24)
6
ELD
(27)
OTIS
FIELD COMPONENT MANUAL
4 - AA3
No.:
GBA 26800BA IV
Vintage: 01 / 1
Central & East Europe Area
FOD BERLIN
3.2.2
Part:
Service Tool Manual
Page:
5/ 35
TCB
Date:
17-Aug-2009
Tools Path
M
TCB - Menu 1 SYSTEM - Menu
F
S
Legend: 1
Service Tool Key Menu System Function
(13)
Page number
2 TOOLS - Menu
(31)
1
Search IO
(31)
2
Erase IO
(32)
3
Setup INST
(32)
4
Setup Door
(33)
9
Opr. Memory (33)
OTIS
FIELD COMPONENT MANUAL
4 - AA3
No.:
GBA 26800BA IV
Vintage: 01 / 1
Central & East Europe Area
FOD BERLIN 3.2.3
Part:
Service Tool Manual
Page:
6/ 35
TCB
Date:
17-Aug-2009
Short Keys S4 – S9
The Short Keys provide direct access to certain , often used Service Too functions, eliminating the need to step through the menu structure. The Service Tool functions Input, Calls, Install, RSL and Events are assigned to the Standard Short Keys S4 (Shift 4), S5 (Shift 5), S6 (Shift 6), S7 (Shift 7), S8 (Shift 8). Short Key S9 (Shift 9) is a free programmable key to store any position of the Tree – Structure as a sixth Short Key. Once you have stored S9 (by pressing S9 at the desired position) you can reset it only on level M (TCB – Menu).
S4 = Install S5 = RSL S6 = Event
S7 = Inputs S8 = Calls S9 = Prog
3.2.3.1 Standard Short Keys TCB – Menu
TOOLS – Menu
SYSTEM – Menu
STATUS – Menu
TEST – Menu
SETUP – Menu
Search IO Erase IO
S8
Calls
S6
Events
S4
Install Setup INST
S7
Input
Diagnosis
S5
RSL
Opr.Memory
Example A – 00 IDL ST ] [ ] [ u d l ux
The current function may be STATUS / Output
Short Key S8: Direct call of function STATUS / Calls
A – 00 IDL ST ] [ ] [ C < U00 D00 A 1 - C
OTIS
FIELD COMPONENT MANUAL
Part:
4 - AA3
No.:
GBA 26800BA IV
Vintage: 01 / 1
Central & East Europe Area
FOD BERLIN
Service Tool Manual
Page:
7/ 35
TCB
Date:
17-Aug-2009
3.2.3.2 Programmable Short Key S9 TCB – Menu
TOOLS – Menu
SYSTEM – Menu
STATUS – Menu
TEST – Menu
SETUP – Menu
Search IO Erase IO
S8
Calls
S6
Events
S4
Install Setup INST
S7
Diagnosis
Input Output
9
Part
S5
5
RSL
Opr.Memory
Allowed
In the figure you can see the function of Short Key S9. In this example the function STATUS / Output is set to the Short Key S9 function. Now S9 is acting like a Standard Short Key. In the figure the current position is SETUP / RSL. Now you can call the function STATUS / Output with Short Key S9. Example A – 00 IDL ST ] [ ] [ u d l ux
Function STATUS / Output should be set as a Short Key Function: First you have to call STATUS / Output.
Short Key S9: Position STATUS / Output is set to the Short Key S9 function. Key MODULE and Shift Key ON: The status of Store Key S9 is displayed on the TCB-Menu.
TCB - Menu SVT-Key PROG: on
Short Key S9 and TCB-Menu: Reset of Short Key S9
TCB - Menu SVT-Key PROG: off
IO I AD P AD P >0000
Now you can toggle between any function SETUP / RSL and STATUS / Output.
Short Key S9: Call of function STATUS / Output.
A – 00 IDL ST ] [ ] [ u d l ux
OTIS
FIELD COMPONENT MANUAL
4 - AA3
No.:
GBA 26800BA IV
Vintage: 01 / 1
Central & East Europe Area
FOD BERLIN
Part:
Service Tool Manual
Page:
8/ 35
TCB
Date:
17-Aug-2009
3.3 System – Menu 3.3.1
Status – Menu ( )
System-Menu = 1 Status-Menu = 1
SYSTEM – Menu Status=1 Test=2 STATUS – Menu Calls=1 Inputs=2 Car identifier
A – 00 IDL ST ] [ ] [ C> U00 D00 A 1C
A B C Direction
A – 00 IDL ST ] [ ] [ C> U00 D00 A 1C
U D Position
A – 00 IDL ST ] [ ] [ C> U00 D00 A 1C
00 ** OCSS mode
A – 00 IDL ST ] [ ] [ C> U00 D00 A 1C
IDL
MCSS state A – 00 IDL ST ] [ ] [ C> U00 D00 A 1C
ST
Doors states A – 00 IDL ST ] [ ] [ C> U00 D00 A 1C
][ ][
DDO
Description first car of group / Simplex second car in group third car in group Description top / direction not defined car is moving in UP direction car is moving in DOWN direction Description actual level (level 0) position not defined Description current OCSS –mode (Idle) see document: Service Tool Manual / Operational Modes Description current MCSS –state (Stop) See document: Service Tool Manual / Motion States Description front / rear door state: ] [ for Closed [ ] for Open for Opening >< for Closing ** for door state not defined when DDO switch was switched and doors are closed
OTIS
FIELD COMPONENT MANUAL
FOD BERLIN
A – 00 >TCI-LOCK ! C> U00 D00 A 1C
4 - AA3
No.:
GBA 26800BA IV
Vintage: 01 / 1
Central & East Europe Area
A – 00 INS IN ] [ ] [ C> U00 D00 A 1C
Part:
Service Tool Manual
Page:
9/ 35
TCB
Date:
17-Aug-2009
In additional a blinking Event Message will be displayed during Software Status Display if one of the following events occurs and the elevator is blocked. Examples: Event Message >TCI – LOCK ! >LS – Fault ! >start DCS ! >1LS+2LSon
Description ”Leave Top of Car” function on 1LS/2LS check negative Door Check Sequence not operated yet 1LS and 2LS is operated
3.3.1.1 Calls - Function ( ) Calls = 1
Short Key:
A – 00 IDL ST ] [ ] [ C> U00 D00 A 1C
The first row displays the Software Status. The second row controls the Elevator Calling System. - You can enter a Car Call, Up Hall Call, Down Hall Call or Emergency Hospital Call - Monitoring of: - number of Upper and Lower Call demands - Load Status - number of cars available in group - power supply
Enter a call 1) 2)
Calls
A – 00 IDL ST ] [ ] [ C>02 U01 D00 A 1C
S8
Call Type / Level Number
1)
C U D E
Car Call Up Hall Call Down Hall Call Emergency Hospital Call
2)
02
entered call (level 2)
With GOON / GOBACK you can toggle trough the Call Types C, U, D and E. 1)
2)
A – 00 IDL ST ] [ ] [ C>02 U01 D00 A 1C
Call Demands 1)
01
number of UP-Call demands
2)
00
number of DOWN-Call demands
OTIS
FIELD COMPONENT MANUAL
4 - AA3
No.:
GBA 26800BA IV
Vintage: 01 / 1
Central & East Europe Area
FOD BERLIN
Part:
Service Tool Manual
Page:
10/ 35
TCB
Date:
17-Aug-2009
Load Status A – 00 IDL ST ] [ ] [ C>02 U01 D00 A 1C
A – 00 IDL ST ] [ ] [ C>02 U01 D00 A 1C
A F P O D
ANS load full load peak load overload default load Cars available in group
1–3
number of cars available in group Power Supply
A – 00 IDL ST ] [ ] [ C>02 U01 D00 A 1C A – 00 IDL ST ][ ][ C>02 U01 D00 A–1C 3.3.1.2 Input Function
Input = 2
C E
Normal power supply Emergency power supply
( ) Short Key:
S7
A – 00 IDL ST ] [ ] [ ins es dw DFC
The first row displays the Software Status. The second row monitors the System Inputs. - lower case letters of the input name stands for ”Function = OFF” and upper case letters for ”Function = ON”. - Up to four signals are displayed in one group. You can skip to the next / previous group with Key GOON / GOBACK. - Each group is assigned to a functional block. Both can be displayed with ENTER. Please refer to the list of available System Inputs. ( see document: Service Tool Reference List)
A – 00 IDL ST md aes
Key GOON / Shift Key GOBACK: Skip to the next / previous group of the System Inputs.
][][
Shift Key UP / DOWN: Row one: Display of the functional block and the current group. SY1 Safety Chain ins es dw DFC
Safety Chain Shift Key ON: Jump to first page of inputs (safety chain)
OTIS
FIELD COMPONENT MANUAL
4 - AA3
No.:
GBA 26800BA IV
Vintage: 01 / 1
Central & East Europe Area
FOD BERLIN
Part:
Service Tool Manual
Page:
11/ 35
TCB
Date:
17-Aug-2009
3.3.1.3 Output – Function ( ) Output = 3 A – 00 IDL ST ] [ ] [ u d l ux
The first row displays the Software Status. The second row monitors the System Outputs. - lower case letters of the output name stands for ”Function = OFF” and upper case letters for ”Function = ON”. - Up to four signals are displayed in one group. You can skip to the next / previous group with Key GOON / GOBACK. - Use Shift Key ENTER to display the current Drive Type instead of the Software Status. Please refer to the list of available System Inputs. ( see document: Service Tool Reference List)
A – 00 IDL ST ] [ ] [ v1 v2 v3 v4
Key GOON / Shift Key GOBACK: Skip to the next / previous group of the System Outputs. Shift Key UP / Shift Key DOWN: Row one: Display of the current Drive Type.
OVF20 > v1 v2 v3 v4
Drive: OVF20 3.3.1.4 Group – Function ( ) Group = 4 A – 00 IDL ST B – 03 IDL ST
][][ ][][
The first row displays the Software Status of the Controller the Service Tool is connected with. The second row displays the Software Status of one of the Other Controllers in the group.
Key GOON / GOBACK: Skip to the next / previous Controller in the group.
A – 00 IDL ST C – 07 IDL ST
][][ ][][
3.3.1.5 ICSS – Function ( ) ICSS = 5 ICSS IS ONLINE ICSS2 IS OFFLINE
The first row displays the status of the first ICSS. The second row displays the status of the second ICSS.
OTIS
FIELD COMPONENT MANUAL
Part:
4 - AA3
No.:
GBA 26800BA IV
Vintage: 01 / 1
Central & East Europe Area
FOD BERLIN
Service Tool Manual
Page:
12/ 35
TCB
Date:
17-Aug-2009
3.3.1.6 Command – Function ( ) Cmd = 6 A – 00 IDL ST ] [ ] [ F:CLD1 R:CLD1
The first row displays the Software Status. The second row displays the Commands which are sent to the internal Subsystems. (see document: Service Tool Reference List / Commands)
1)
Display Field
A – 00 IDL ST ] [ ] [ F:CLD1 R:CLD1 2)
1) 2) 3)
IDL CLD1 CLD1
Description Software Status command for front door command for rear door
3)
With Key GOON / Shift Key GOBACK: skip to the next / previous group of commands. 1) A – 00 IDL ST ] [ ] [ MC: GoTo To: 00 2) 3)
Display Field
Description
1) 2) 3)
Software Status Motion command Actuell Target (** = invalid)
IDL GoTo 00
(Hint: There are more indications for DCSS5 (Door = 12)!) 3.3.2
TEST - Functions ( )
System-Menu = 1 Test-Menu =2
SYSTEM – Menu Status=1 Test=2 TEST – Menu > Events=1 Diag=2 TEST – Menu > Part=3 RSL=4 TEST – Menu > Selft.=5
There are the Events, Diagnosis, Part, RSL and Selftest functions, which are the most used functions for service and maintenance. Short Key S6 is assigned to call the Events-function. Part display the configuration number of EPROM and EEPROM. RSL and Selftest are functions to test the hardware of the TCB. 3.3.2.1 Event – Function ( )
OTIS
FIELD COMPONENT MANUAL
FOD BERLIN Event = 1
1) 00000 00000
4 - AA3
No.:
GBA 26800BA IV
Vintage: 01 / 1
Central & East Europe Area
00000 00000
Part:
Service Tool Manual
Page:
13/ 35
TCB
Date:
17-Aug-2009
Short Key = S6 total runs minutes on
The Event – Function supports the maintenance of the elevator. It displays - the total number of runs - the elapsed time since Power On - information about each event: + event text + the number of events + the elapsed time since last occurrence + the car position where the last event occurred Please refer to the list of Event Messages. See document: Service Tool Reference List
2)
Global information
total runs minutes on
1) 2)
00000 00000
number of elevator runs minutes since Power On
With Key GOON / Shift Key GOBACK skip through the list of recorded event messages. Event logging Event logging 1) 0400 RSL parity c002 t00001 p** 2)
3)
1) 2) 3)
first row 002 00001
4)
**
4)
event text number of events since Power On elapsed time since last occurrence (minutes) car position where the last event occurred (** = position not defined)
Event reset - Shift Key ON: Resets the displayed event. -
Shift Key ENTER: Termination of the reset function.
-
Shift Key UP: Resets the entire event logging.
-
Key 1 and ENTER and Key 2 and ENTER: Termination of the reset function - Key CLEAR: back to Test- Menu
Erase Value ? done ! Erase Events ? n=0 y=1 > Erase Events ? please wait !
3.3.2.2 Diagnosis – Function ( )
OTIS
FIELD COMPONENT MANUAL
Part:
4 - AA3
No.:
GBA 26800BA IV
Vintage: 01 / 1
Central & East Europe Area
FOD BERLIN
Service Tool Manual
Page:
14/ 35
TCB
Date:
17-Aug-2009
Diagnosis = 2 01 DIAG ACT-T 000 : 00 : 00 : 34
The first row displays the name of the current diagnosis Parameter. The second row shows the value of the diagnosis parameter.
You can skip to the next / previous diagnosis parameter with Key GOON / GOBACK. With Key UP you can display a short legend for the time values. The displayed parameter can be reset to zero using the key sequence ON/UP and ENTER. Please refer to the list of Diagnosis Parameters. Diagnosis parameters display Example of a time parameter 1)
2)
01 DIAG TOT-T 007 : 05 : 11 : 30 3)
4)
5)
6)
Display Field 1) 2) 3) 4) 5) 6)
01 TOT-T 007 05 11 30
Description Parameter no. Parameter name No. of months No. of days No. of hours No. of minutes
Example of a count parameter 1)
2)
03 DIAG UP-CNT 000000081 3)
Display Field 1) 2) 3)
03 UP-CNT 000000081
Description Parameter no. Parameter name No. of occurrences
Diagnosis parameter reset Erase Value ? 02 DIAG TOT-T
-
Shift Key ON: Resets the displayed event.
-
Shift Key ENTER: Termination of the reset function.
-
Shift Key UP: Displays a short legend of the time value
Mon : d : h : min 007 : 05 : 11 : 30
-
Shift Key UP (a second time) Resets the entire event logging
Erase Events ? n=0 y=1 >
- Key 1 and ENTER and Key 2 and ENTER:
Erase Value ? done !
Erase Events ? please wait !
OTIS
FIELD COMPONENT MANUAL
Part:
4 - AA3
No.:
GBA 26800BA IV
Vintage: 01 / 1
Central & East Europe Area
FOD BERLIN
Service Tool Manual
Page:
15/ 35
TCB
Date:
17-Aug-2009
Termination of the reset function. - Key CLEAR: back to Test -Menu 3.3.2.3 Part – Function ( ) Part = 3 No. GAA30084 AAA 11-Jul-1999 08:30
The Part – Function displays the current software version of the EPROM and EEPROM. It also displays the date and the time of the TCB software release.
With Key GOON / Shift Key GOBACK you can toggle between the displays of the EEPROM version and the display that shows the EPROM version and the date /time of the release. Key CLEAR: back to Test - Menu Software version / date / time EE=E47NE4711 11-Jul-1999 08:30 No. GAA30084 AAA 11-Jul-1999 08:30
1) E47NE4711 2) GAA30084AAA 3) 11-Jul-99 4) 08:30
EEPROM version EPROM version date and time of the release
3.3.2.4 RSL-Test Function ( ) RSL = 4 The RSL-Test Function can be used to test the Remote Stations. After the address of the Remote Station is entered, - the four Input Pins are monitored and - the four Output Pins can be set.
ADR=
Enter the RSL – address Key 1,5:
Input Keys of the RSL –address
ADR=15
Key CLEAR: deletes the last input if you want to correct the number Shift Key ENTER: termination of the input operation The current status of the Input and Output Pins of The entered RSL address is displayed.
ADR=15 IN:off
BIT=1 OUT:off
Key GOON / Shift Key GOBACK:
ADR=16 IN:off
BIT=1 OUT:off
OTIS
FIELD COMPONENT MANUAL
Part:
4 - AA3
No.:
GBA 26800BA IV
Vintage: 01 / 1
Central & East Europe Area
FOD BERLIN
Service Tool Manual
Page:
16/ 35
TCB
Date:
17-Aug-2009
Skip to next / previous address. Shift Key UP / Shift Key DOWN: Skip to the next / previous bit.
ADR=16 IN:off
BIT=2 OUT:off
Shift Key ON / Shift Key OFF: Toggle of the Output-Pin: on / off
ADR=16 IN:off
BIT=2 OUT:on
Key Clear: Back to Test-Menu 1)
2) 3)
ADR=16 IN:off
RSL: Pin status 4)
BIT=1 OUT:off
(on = active / off = not active)
1) ADR 2) BIT 3) IN 4) OUT
RSL address RSL pin RSL Input Pin status (Monitor) RSL Output Pin status
3.3.2.5 Selftest –Function ( ) Selftest = 5 PR ?
EE ? RS ?
RA ?
Function Selftest can be used - to test the memory of the TCB board and - to check the Remote Serial Link. The test will start as soon as the Selftest –Function is called.
The flashing question mark indicates which part of the test is currently active: - PR EPROM -test - EE EEPROM –test - RA RAM –test - RS Remote Serial Link –test The single results are displayed as: - (+) for Test successfully finished - (-) for Test not successfully finished Please notice that for the EE –test a checksum written into the EEPROM is verified. So, the first call of the test with a new EEPROM will result a (-). PR +
EE RS ?
RA ?
PR +
EE + RA + RS 16aR000
PR +
EE + RA + RS 16aR000
The RS –test will give some information about single Remote Station. - if they are set up but not available - if they are responding - if there are parity errors RS -test
OTIS
FIELD COMPONENT MANUAL
Part:
4 - AA3
No.:
GBA 26800BA IV
Vintage: 01 / 1
Central & East Europe Area
FOD BERLIN
Service Tool Manual
Page:
17/ 35
TCB
Date:
17-Aug-2009
16
RSL -address
A a
available (IO-No. is defined) not available
R r
responding (Hardware is okay) not responding
000
parity error counter
Key GOON / Shift Key GOBACK: Skip through the list of Remote Stations which signals - not available or - not responding or - parity errors. If there was at least one entry in the list, the display for Test not successfully finished (-) occurs.
PR +
EE + RA + RS 48Ar000
PR +
EE + RS -
RA +
Key Clear: Back to Test –Menu. 3.3.3
SETUP –Function ( )
System = 1 Setup = 3 In the following all the SETUP –functions are explained. The Install-, RSL-, Allowed-, POS- and ELD- functions are used to set the parameters and masks of the EEPROM where the DCS Run function has the task to check if every open door opens the safety chain. There are four different groups of Setup Parameters to define the elevator environment: - Installation Parameters - RSL – IO Numbers - Allowed Masks - Position Indicator Parameters - ELD - Display The DCS – Function is used to test the well installed Door safety chain after startup and setup phase.
3.3.3.1 Install –Function ( ) Install = 1
Short Key S4
OTIS
FIELD COMPONENT MANUAL
Part:
4 - AA3
No.:
GBA 26800BA IV
Vintage: 01 / 1
Central & East Europe Area
FOD BERLIN
Service Tool Manual
Page:
18/ 35
TCB
Date:
17-Aug-2009
System = 1 OCSS = 2 : Security = 9 Test with Install – Menu 01 System
Function Install is used to set Installation Parameters. The parameters are divided into 8 groups. The Install Menu gives access to each group.
>
000 System new TOP = 004>
1)
The range of each parameter is defined and controlled by software. The storage operation is disabled if the car is moving. (see document: List of Installation Parameters)
2)
Element-No. / Group / Name
000 System new TOP = 004> 3)
1) 000 2) System 3) TOP
element-No. of group current group name name of current Install Parameter
Key GOON / Shift Key GOBACK: Skips through the assigned group of Installation Parameter. Key CLEAR: Back to Install - Menu Enter a new parameter 000 System new TOP = 004> 1)
Input: Install Parameter 1) 2)
004 000
current value of Install Parameter input field for new parameter
2)
Key 3,2: Input keys of the new parameter (32) Key CLEAR: Deletes the last input if you want to correct the number
Shift Key ENTER: Termination to store the new Install Parameter into the EEPROM 3.3.3.2 RSL –Function ( ) RSL = 2
Short Key S5
000 System TOP = 004>032 000 System TOP = 004>003
new
new
000 System new TOP = 003>
OTIS
FIELD COMPONENT MANUAL
FOD BERLIN
I AD P
AD P
4 - AA3
No.:
GBA 26800BA IV
Vintage: 01 / 1
Central & East Europe Area
IO >
Part:
Service Tool Manual
Page:
19/ 35
TCB
Date:
17-Aug-2009
The arrow is pointing to the input field of the IO-Number. After you entered the IO-Number the current RSL information stored in the EEPROM is displayed. Now you can change the RSL-Address and the RSL-Plug. The Invert Bit can not be changed. It is set by software. For RSL-Address 0 up to 4 it is always set to zero. ( see document: List of Inputs and Outputs)
Key 2,2,2: Input Keys of the desired IO-Number (222)
IO I AD P AD P >0222
Key CLEAR: Deletes the last input if you want to correct the number IO I AD P AD P 0222=0 57 2>
Shift Key ENTER: Termination of the IO-Number input The current information stored in the EEPROM is displayed: IO: IO – Number AD: Remote Station – Address I: Invert Bit P: Remote Station - Plug Note:
Once a IO-number is defined, it is stored in the system!
Key CLEAR: Clears the display to enter a new IO-number.
IO >
I AD P AD P
Change the IO - Number Key GOON / Shift Key GOBACK: Skip to the next / previous IO – number. Shift Key UP / Shift Key DOWN: Skip to the next / previous IO-number with defined RSL-Addr. And RSL-Pin/Plug. Enter new RSL – Parameter 1) 2) IO I AD P AD P 0032=0 04 2> Key 0,4,2: Input Keys of
Input: RSL - Parameter 1) 2)
AD P
RS-Addr.: 04 and RS-Pin: 2
Shift Key ENTER: Termination of the RSL-Parameter input operation.
new RSL-Address new RSL-Pin/Plug IO I AD P AD P 0032=0 57 2> 04 2
OTIS
FIELD COMPONENT MANUAL
Part:
4 - AA3
No.:
GBA 26800BA IV
Vintage: 01 / 1
Central & East Europe Area
FOD BERLIN
Service Tool Manual
Page:
20/ 35
TCB
Date:
17-Aug-2009
Key CLEAR: Deletes the last input if you want to correct the number. Setup inverted I/O After entering an I/O-number the following display will be shown: 1
9
...
IO I AD P AD P 0001=1 16 3>
1:
0: normal signal 1: inverted signal 16 3: RSL address
alternating display IO inverted IO! 0001=1 16 3>
< 1 > ... < 9 > < ON > < ENTER > Note:
Enter two digits to enter a emote Station address and a pin number. Use ON to toggle the type of the remote signal (inverted / not inverted) Press ENTER to store the changed value.
To invert an already programmed IO the shown address must be entered again!
3.3.3.3 Allowed – Function ( ) Allowed = 3 Enable = 1 Cut Call = 2 Card Reader = 3 ALLOWED – Menu 01 Enable at CUDE CUDE P R 00 1100 0000 0 0
Function Allowed is used to set the Floor Table Masks. The masks are divided into 3 groups: - Enable - Cut Call - Card Reader. The Allowed Menu gives access to each group.
Enable Display ( ) 1) 2) 3) 4) 5) Enable Display
OTIS
FIELD COMPONENT MANUAL
Part:
4 - AA3
No.:
GBA 26800BA IV
Vintage: 01 / 1
Central & East Europe Area
FOD BERLIN
at CUDE CUDE P R 00 1100 0000 0 0
Service Tool Manual
Page:
21/ 35
TCB
Date:
17-Aug-2009
1) at
level number (0)
2) CUDE 3) CUDE - C - U - D - E
front door Enable Mask and rear door Enable Mask, with: - Car Call - Up Hall Call - Down Hall Call - Emergency Hospital Call (1 = allowed / 0 = not allowed)
4) P
Parking Bit: (1 = not allowed / 0 = allowed)
5) R
Reduced Landing No.: - Short Run (1,2,3 = profile) - Medium Run (4,5,6 = profile)
The Enable Masks (CUDE) allows the Elevator to run to a certain level depending on the regarding call. If the Parking Bit is set to 1, parking at a certain level is not allowed (Group application). The Reduced Landing No. indicates that the above floor is a Short- or Medium- Landing. The velocity (profile) is a function of the number (1,2,3 or 4,5,6). 3.3.3.3.1 Cut Call Display ( ) 1)
2)
3)
at CUDE CUDE 00 1100 0000
4) OP 0
Cut Call Display 1)
at
level number (0)
2) 3)
CUDE CUDE - C - U - D - E
front door Cut Call Mask and rear door Cut Call Mask, with: - Car Call - Up Hall Call - Down Hall Call - Emergency Hospital Call (1 = allowed / 0 = not allowed)
4)
Op
Parking with door open 0 = both doors closed 1 = only front door open 2 = only rear door open 3 = both doors open
The Cut_Call Masks (CUDE) are used to supress the Enable Mask if a Cut_Call Signal (CHCS) occurs. The indication Parking with door open defines the door state during parking.
OTIS
FIELD COMPONENT MANUAL
Part:
4 - AA3
No.:
GBA 26800BA IV
Vintage: 01 / 1
Central & East Europe Area
FOD BERLIN
Service Tool Manual
Page:
22/ 35
TCB
Date:
17-Aug-2009
3.3.3.3.2 Card_Reader Display ( ) 1) 2) 3) 4) Card_Rd Display at CUDE CUDE 00 1100 0000
Sb 0
1)
at
level number (0)
2) 3)
CUDE CUDE - C - U - D - E
front door Card_Rd Masks and rear door Card_Rd Masks, with: - Car Call - Up Hall Call - Down Hall Call - Emergency Hospital Call (1 = allowed / 0 = not allowed)
4)
Sb
Special door open button 0 = both SDOB disabled 1 = only front SDOB enabled 2 = only rear SDOB enabled 3 = both SDOB enabled
The Card_Rd Masks (CUDE) are used to reach certain floors with magnetic card (Card Reader Operation). The indication Special door open button defines the operation of the Special Door Open Button. Change the level Key GOON / Shift Key GOBACK: Skip to the next level number
at CUDE CUDE P R 00 1100 0000 0 0
Key CLEAR: Back to Allowed Menu Enter new Allowed – Parameter Key 0,1,0,...: Input Keys of all the numbers (10) of the current row.
at CUDE CUDE P R 00 1100 0000 0 0
Key CLEAR: Deletes the last input if you want to correct the number. Shift Key ENTER: Termination of the Allowed Parameter input operation.
3.3.3.3.3 Openings and Dummy Doors at CUDE CUDE P R 00 1100 0000 0 0
For the controller with TCB Openings and Dummy Doors are defined as follows:
OTIS
FIELD COMPONENT MANUAL
Part:
4 - AA3
No.:
GBA 26800BA IV
Vintage: 01 / 1
Central & East Europe Area
FOD BERLIN
Service Tool Manual
Page:
23/ 35
TCB
Date:
17-Aug-2009
The Openings are determined by Software regarding to the Level Arrangement done with Function Allowed-Enable and the following Rule. Important! Count the Front- and Rear Doors for each Level beginning at Level 0 / Frontside.
A Dummy door is an option to define the same Level Arrangement for every elevator in Group applications. at F: 00 R: -00 1100 0000
P R 0 0
Key 2,0,0,0...: Input Keys of all the numbers of the current row (level 1) 2000 is the Code for a Dummy Door.
at F: 01 R: -01>2000
P R
Shift Key ENTER: Termination of the Allowed-Parameter input operation. The new determined Openings are displayed.
at F: 01 R: 02 01 2000 1110
P R 0 0
Shift Key UP: < toggle key > Display of the determined Openings. F: 00 R: --
at Front Door of Level 0: Opening 0 at Rear Door of Level 0: no Opening
F: 01 R: 02
at Front Door of Level 1: Opening 1 at Rear Door of Level 2: Opening 2
3.3.3.4 POS – Function ( ) POS = 4 Pos.Ind. at: L 00 = 10
Function POS is used to set the digits of the Position Indicator. For each level a left (L) and a right (R) digit is provided to indicate the floor. The range of each digit is defined in the table below.
new >
Input: POS digits
Pos.Ind. new at: L 00 = 10 > 1)
2)
3)
1)
L R
left digit right digit
2)
00
level number (00)
3)
10
current value of Pos.Ind. digit (10 = blank)
4)
new
input field for new value
4)
Key GOON / Shift Key GOBACK: Skip first to the next / previous digit and then to the next / previous level.
Pos.Ind. new at: R 00 = 00 >
OTIS
FIELD COMPONENT MANUAL
Part:
4 - AA3
No.:
GBA 26800BA IV
Vintage: 01 / 1
Central & East Europe Area
FOD BERLIN
Service Tool Manual
Page:
24/ 35
TCB
Date:
17-Aug-2009
Key CLEAR: Back to Setup-Menu. Enter a new digit Key 1,5: Input Keys of the desired digit (15 = E) (see Reference List below)
Pos.Ind. new at: R 00 = 10 > 15
Key CLEAR: Deletes the last input if you want to correct the number. Shift Key ENTER: Termination of the input operation. The current information stored in the EEPROM is diplayed:
Pos.Ind. new at: R 00 = 15 >
Reference List Value Symbol Value 0 0 10 1 1 11 2 2 12 3 3 13 4 4 14 5 5 15 6 6 16 7 7 17 8 8 18 9 9 19 (* for 16-segment only!)
Symbol (blank) A B* C D* E F G* H I*
Value 20 21 22 23 24 25 26 27 28 29
Symbol J* K* L M* N* O P Q* R* S
Value 30 31 32 33 354 35 36 37
Symbol T* U V* W* X* Y* Z* -
3.3.3.5 Door Check Sequence ( ) DCS = 5 The Door Check Sequence (DCS) –Function is a safety feature for OTIS2000 MRL. It insures that all hoistway door contacts are installed correctly and will open the safety chain, if a door opens. Until the Door Check Sequence is finished successfully it is only possible to move the car in inspection mode. Normal runs are disabled. The calibration menu appears in following case: OVFWW EN-ADO = 0 EN-RLV = 0 Allow Normal Start DCS
=0 =1
Key 0: From now 10 normal runs are allowed to calibrate the drive package. Key 1: Start the DCS-run immediately.
OTIS
FIELD COMPONENT MANUAL
4 - AA3
No.:
GBA 26800BA IV
Vintage: 01 / 1
Central & East Europe Area
FOD BERLIN
Part:
Service Tool Manual
Page:
25/ 35
TCB
Date:
17-Aug-2009
Otherwise it is possible to enter commands for runs in normal mode to Top or Bottom landing if you push the CCTL- or CCBL- button on the SBP. After selecting ”0” the following message is displayed until the max number of runs have been completed: Now calibrate Drive package!
Key CLEAR: jump back to previous menu to start DCS-run
Note: If the number of runs are not done within a specific time then the previous menu is displayed and ”0” has to be pressed again to allow further calibration runs. Starting the Door Check Sequence Before you can start the DCS-run the start conditions have to be checked. If any condition is not fulfilled an error message is displayed. DCS Start Error Setup C-Type:
Error Message
Error Reason
Setup C-Type: C-Type not 2 or 3 Not able to run! OCSS mode is NAV Switch of INS! OCSS mode is INS Already done DCS already performed Into 1LS and DZ! Car is not in 1LS and DZ Leave 1LS Car in 1LS but not DZ If no start error is detected you can start the DCS-run by pressing ENTER. to start DCS press ENTER
Key ENTER: Start the automatic DCS run.
The automatically performed DCS-run can be followed on the SVT display. Direction - 00 DW: clsd ][ ][ open front door
U D Position
- 00 DW: clsd ][ ][ open front door
00 **
DW status - 00 DW: clsd ][ ][ open front door
DW: clsd dw: opnd
Description stop / direction not defined car is moving in UP direction car is moving in DOWN direction Description actual level (level 0) level position not defined
Description DW active (switch closed, door closed) DW passive (switch opend, door opend)
OTIS
FIELD COMPONENT MANUAL
GBA 26800BA IV
Page:
26/ 35
TCB
Date:
17-Aug-2009
][ ][
Description front / rear door state: ] [ for Closed ] [ for Open for Opening >< for Closing * * for door state not defined
Door action - 00 DW: clsd ][ ][ open front door
No.:
Service Tool Manual
Doors states - 00 DW: clsd ][ ][ open front door
4 - AA3
Vintage: 01 / 1
Central & East Europe Area
FOD BERLIN
Part:
Open front door Check DW input Close front door Open rear door Close rear door Up to next level
Description (listed are the current actions of the automatic DCS-run)
If a failure occurred the error is displayed in the 2 nd row. The 1st row shows the status including the level number where the error was detected: Error message - 00 DW: clsd ][ ][ Front Door Error
Description
Front Door Error (listed are the possible error messages Rear Door Error of the automatic DCS-run) Aborted by ENTER Door opening err DW not closed Position error Door closing Err
After successful completion of the DCS-run the success message is displayed. DCS successfull press GOON > Check PES, GTC ... press GOON > to start normal press GOON >
(as reminder what has to be done next)
(to leave DCS-run)
3.3.3.6 ELD – Function ( ) ELD = 6
OTIS
FIELD COMPONENT MANUAL
Part:
4 - AA3
No.:
GBA 26800BA IV
Vintage: 01 / 1
Central & East Europe Area
FOD BERLIN
Service Tool Manual
Page:
27/ 35
TCB
Date:
17-Aug-2009
The ELD – function is used to define the ”Customer Message” of the OTIS 2000 –ELD. For each floor the Customer Message can be displayed (Floor Display) modified (Edit Display and Default Display) or stored into EEPROM (Store Display). 1)
2)
Floor Display
00
View more...
Comments
