Nokia VS Ericsson

No 1

2

3

4 5

6

7

8

9

10

11

Ericsson Parameter

Object

Nokia Default

Unit

Utran Cell accessClassNBarred 0 (=not barred) Indicates whether access class N (N=0 to 15) is barred or not. 0=not barred, 1=barred

Object

WCEL Define whether the cell is barred or not. UE will even for emergency call purpose.

Utran Cell cellReserved NOT_RESERVED WCEL Indicates if this cell shall be reserved for operator use. If it is reserved, there will be no service Indicates if this cell shall be reserved for operat to the UEs. service to the UEs.. When cell status is "not ba the UEs assigned to Access Class 11 or 15 ma PLMN. UEs assigned to Access Class in the ra if cell status "barred" is indicated.

Utran Cell treSelection 2 s WCEL Time-to-trigger for cell reselection in seconds. Value launched by System information (SIB3). The UE triggers the reselection of a new cell if The UE reselects new cell if the cell reselection criteria are fulfilled during this time interval. during the time interval Treselection. UtranCell

qQualMin

-18

dB

Minimum required (acceptable) quality level in the cell (dB). UtranCell

qRxLevMin

-115

WCEL

The minimum required quality level in the cell ( dBm

WCEL

Minimum required (acceptable) RX level in the cell.

The minimum required RX level in the cell.

ExternalUtranCell qQualMin 100 dB Minimum required (acceptable) quality level in neighbor cell (dB) for cell reselection to that cell. If neighbor cell belong to same RNC, then the Object of parameter will be UtranCell.100 : Indicates that the minimum quality level has not been specified by the operator. The parameter is then not present in SIB11 for this neighbour. The UE will use the serving cell value (UtranCell MO value) instead.

HOPI Determines the minimum required CPICH Ec/N measurement result of the inter-frequency neig becomes possible.

ExternalUtranCell qQualMin 100 dB Minimum required (acceptable) quality level in neighbor cell (dB) for cell reselection to that cell. If neighbor cell belong to same RNC, then the Object of parameter will be UtranCell.100 : Indicates that the minimum quality level has not been specified by the operator. The parameter is then not present in SIB11 for this neighbour. The UE will use the serving cell value (UtranCell MO value) instead.

HOPS Determines the minimum required CPICH Ec/N measurement result of the neighbouring cell be possible.

ExternalUtranCell qRxLevMin 100 dBm Minimum required (acceptable) RX level in neighbor cell (dBm). If neighbor cell belong to same RNC, then object parameter will be UtranCell. 100 : Indicates that the minimum Rx level has not been specified by the operator. The UE will use the serving cell value (UtranCell MO value) instead.

HOPS The parameter determines the minimum requir measurement result of the neighbouring cell m possible.

ExternalUtranCell qRxLevMin 100 dBm Minimum required (acceptable) RX level in neighbor cell (dBm). If neighbor cell belong to same RNC, then object parameter will be UtranCell. 100 : Indicates that the minimum Rx level has not been specified by the operator. The UE will use the serving cell value (UtranCell MO value) instead.

HOPI The parameter determines the minimum requir measurement result of inter-frequency neighbo selection is possible.

ExternalGsmCell qRxLevMin -105 Minimum required (acceptable) RX level in the cell. (dBm).

dBm

HOPG Determines the minimum required RSSI level w GSM neighbour cell must exceed before the ce

-

-

WCEL

-

-

Defines whether intra-frequency cell re-selectio barred. When a cell's status is "barred", the UE cell, except in some cases for an emergency ca

11

-

-

-

-

12

When the cell is barred, the UE must check be period’, whether the status of the barred cell ha

13

WCEL

UtranCell

qHyst1

0

dB

WCEL Qhyst1 is used for TDD and GSM cells, and for Hysterisis value that is read in the system information of serving cell, and used for cell ranking selection quality measure is set to CPICH RSC and cell reselction process. It is used when qualMeasQuantity is set to CPICH RSCP UtranCell

qHyst2

0

dB

14

WCEL Qhyst2 is used for FDD cells when cell selectio to CPICH Ec/No.

Hysterisis value that is read in the system information of serving cell, and used for cell ranking and cell reselction process. It is used when qualMeasQuantity is set to CPICH Ec/No

15

16

17

18

19

20

UtranCell maxTxPowerUl 24 dBm The maximum UE transmission power on the RACH when accessing the system.Used in UE functions for cell selection/reselection in idle mode and connected mode. Also used by UTRAN to control the maximum TX power level an UE may use.If the current UE uplink transmit power is above the indicated power value, the UE shall decrease the power to a level below the power value.

WCEL This parameter defines the maximum transmis It is signaled to UE in the Maximum allowed UL when a radio link is set up.

ExternalUtranCell maxTxPowerUl 100 dBm The maximum UE transmission power on the RACH when accessing the system.Used in UE functions for cell selection/reselection in idle mode and connected mode. Also used by UTRAN to control the maximum TX power level an UE may use.If the current UE uplink transmit power is above the indicated power value, the UE shall decrease the power to a level below the power value.Special values:100: Indicates that the maximum UL transmission power has not been specified by the operator. The parameter is then not present in SIB11 for this neighbour. The UE will use the serving cell value (UtranCell MO value) instead.

ADJI This parameter indicates the maximum transm when accessing inter-frequency neighbouring c parameter in the cell re-selection procedure. If lower than the value of the parameter, the UE a the minimum required CPICH Ec/No level, whic neighbouring cell must exceed before the cell r

ExternalUtranCell maxTxPowerUl 100 dBm The maximum UE transmission power on the RACH when accessing the system.Used in UE functions for cell selection/reselection in idle mode and connected mode. Also used by UTRAN to control the maximum TX power level an UE may use.If the current UE uplink transmit power is above the indicated power value, the UE shall decrease the power to a level below the power value.Special values:100: Indicates that the maximum UL transmission power has not been specified by the operator. The parameter is then not present in SIB11 for this neighbour. The UE will use the serving cell value (UtranCell MO value) instead.

ADJS

ExternalGsmCell maxTxPowerUl 100 dBm The maximum UE transmission power on the RACH when accessing the system.Used in UE functions for cell selection/reselection in idle mode and connected mode. Also used by UTRAN to control the maximum TX power level an UE may use.If the current UE uplink transmit power is above the indicated power value, the UE shall decrease the power to a level below the power value.Special values:100: Indicates that the maximum UL transmission power has not been specified by the operator. The parameter is then not present in SIB11 for this neighbour. The UE will use the serving cell value (UtranCell MO value) instead.

ADJG This parameter indicates the maximum transm when accessing the GSM neighbouring cell on in the cell re-selection procedure. If the maximu the value of the parameter, the UE adds the po minimum required CPICH Ec/No level, which th neighbouring cell must exceed before the cell r

UtranCell sIntraSearch 0 dB The decision on when measurements on intra frequencies shall be performed. If Squal