PT Telkom Vectoring Field Trial
Method of Procedure Alcatel-Lucent 7356REM ISAM Turn Up Guide Author: Document: Version:
Fiona Tay Tay Turn-up Guide 0.1
Status: Last Revised:
Draft June 24, 2014
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 1 of 27
m rof n iot
TABLE OF CONTENTS a
d izr n a o ht e s u u a ,t n n m
tet o
t
e ir u w c u d o si thi th w f o d ngi ite o
e
y mr p c p t d o n n a ts n o n
1
PREFACE ........................................................................................................................................ ............................................................................................................ ............................ 5
2
COMPATIBILITY ......................................................................................................................... .................................................................................. ....................................... 5
3
CONVENTIONS ..................................................................................... ............................................................................................................................ ....................................... 5
4
PRE-CONFIGURATION PRE-CONFIGURATIO N STEPS ................................................................................................ 6
et g ni n
4.1 o
s s c a tsi P . f d o e
5
vr n s
iot st n
e a er ic u h igr m A
ll
m
CONNECT TO THE 7360FX OLT & 7356REM MDU ISAM VIA CRAFT TERMINAL ...... ......................... ................... 6
OLT BASIC SETUP - INITIAL CONFIGURATION .............................................................. ....................................................... ...... 8 5.1
R ESET ESET THE SYSTEM WITH CLEAN DATABASE ............................................................... .............................. ........................................................ ....................... 8
5.2
CONFIGURE UPLINK PORTS .............................................................. ............................. ................................................................. .................................................. .................. 8
5.3
CONFIGURE MANAGEMENT VLAN.............................. .............................................................. ................................................................. ........................................ .......8
5.4
CONFIGURE S YSTEM IP ADDRESS ............................................. .............................................................................. ........................................................ ....................... 8
5.5
CONFIGURE S YSTEM ID ................................. ................................................................. ................................................................ ................................................... ................... 9
5.6
CONFIGURE S YSTEM PROMPT ............................................. .............................................................................. .............................................................. ............................. 9
5.7
CONFIGURE SYSTEM LOGIN BANNER ................................................................ ............................... ................................................................. ....................................9
5.8
CONFIGURE SLOT B ANDWIDTH .................................................................. ............................... ................................................................. ........................................ ........9
5.9
CONFIGURE SLOT NUMBERING & DHCP OPTION82 FORMAT .......................................................... ........................................... .............. 9
o c
5.10
DISABLE PASSWORD AGING & TIMEOUT TIMEOUT FOR OPERATOR LOGIN .................................................. 10
5.11
CONFIGURE THE SNMP COMMUNITIES ................................................................ ................................. ...................................................... ....................... 10
5.12
S AVE THE CONFIGURATION CONFIGURATION .............................................................. ............................. .................................................................. ........................................... .......... 10
5.13
CONFIGURE SNTP ................................................................ ............................... ................................................................. ...................................................... ...................... 10
5.15
ENABLE PON PORTS .................................................................................................................. 10
5.16
R EBOOT EBOOT 7360FX OLT ............................................................... .............................. ................................................................. ................................................. ................. 11
5.14
6
PLAN ALL INSERTED CARDS .............................................................. ............................. .................................................................. ........................................... .......... 10
MDU BASIC SETUP - INITIAL CONFIGURATION .......................................................... 12 6.1
R ESET ESET THE SYSTEM WITH CLEAN DATABASE ............................................................... .............................. ...................................................... ..................... 12
6.2
CONFIGURE UPLINK PORTS .............................................................. ............................. ................................................................. ................................................ ................ 12
6.3
CONFIGURE MANAGEMENT VLAN.................................................................................................... 12
6.4
CONFIGURE S YSTEM IP ADDRESS ............................................................. ............................. ................................................................. ...................................... ..... 12
6.5
CONFIGURE S YSTEM ID ................................. ................................................................. ................................................................ ................................................. ................. 12
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 2 of 27
m or f n iot a d izr n a o ht e s u u a ,t n n m
tet o
t
e ir u w c u d o si ht th
6.6
CONFIGURE S YSTEM PROMPT .............................................................. ............................. .................................................................. ........................................... .......... 13
6.7
CONFIGURE SYSTEM LOGIN BANNER ................................................................ ............................... ................................................................. ................................ 13
6.8
CONFIGURE SLOT B ANDWIDTH .................................................................. ............................... ................................................................. ...................................... ...... 13
6.9
CONFIGURE SLOT NUMBERING & DHCP OPTION82 FORMAT ........................................................ ............................. ........................... 13
i w f
o d ngi tei o
e
y mr p c p t d o n n a st n o n te g ni n o s s c a tsi P . f d o e rv n s
iot st n
e a er ic u h gi m A
ll
r m o c
7
8
9
6.10 6.11
TIMEOUT FOR OPERATOR LOGIN .................................................. 13 DISABLE PASSWORD AGING & TIMEOUT CONFIGURE THE SNMP COMMUNITIES ................................................................ ................................. ...................................................... ....................... 14
6.12
S AVE THE CONFIGURATION CONFIGURATION .............................................................. ............................. .................................................................. ........................................... .......... 14
6.13
CONFIGURE SNTP ................................................................ ............................... ................................................................. ...................................................... ...................... 14
6.14
PLAN ALL INSERTED CARDS .............................................................. ............................. .................................................................. ........................................... .......... 14
6.15
R EBOOT EBOOT ISAM ........................................................................................................................... 14
OLT SERVICE PROVISIONING - INITIAL CONFIGURATION .................................... 15 7.1
CREATE UPSTREAM B ANDWIDTH PROFILES (DBA) ............................................. ........................................................................ ........................... 15
7.2
CREATE DOWNSTREAM SHAPER PROFILES ................................................................ ................................ ...................................................... ...................... 15
7.3
CREATE PBIT TO TC M APPING PROFILES........................................................................................ 15
7.4
CONFIGURE S YSTEM MULTICAST FOR IPTV ........................................................ ................................................................................... ........................... 15
7.5
CREATE VLANS .............................................................................................................................. 16
MDU SERVICE PROVISIONING - INITIAL CONFIGURATION................................... 18 8.1
CREATE VECTORING CONTROL ENTITY (VCE) PROFILE AND ASSOCIATE IT TO A BOARD ............... 18
8.2
CREATE XDSL V VECTORING PROFILES ............................................................. ............................ ................................................................. ................................ 18
8.3
CREATE XDSL SERVICE PROFILES ............................................................ ............................................................................................. ...................................... ..... 18
8.4
CREATE XDSL SPECTRUM PROFILES ............................................................... .............................. ................................................................. ................................ 18
8.5
CREATE XDSL R TTXX PROFILES .............................................................. ............................. .................................................................. ........................................... .......... 21
8.6
CONFIGURE S YSTEM MULTICAST FOR IPTV ........................................................ ................................................................................... ........................... 21
8.7
CREATE VLANS ............................................................................................................................. 22
8.8
CREATE VOIP SERVICE ................................................................................................................. 22
SERVICE PROVISIONING SAMPLE SERVICE CONFIGURATION ......................... ......................... 24 –
9.1
CREATE SFP ONT INFRASTRUCTURE ............................................................. ............................ ................................................................ ............................... 24
9.2
CONFIGURE SFP ONT UNI ................................................................. ................................ ................................................................ .......................................... ........... 24
9.3
CREATE HSI SERVICE ON SFP ONT .............................................................. ............................. ................................................................ ............................... 24
9.4
CREATE VOD + MULTICAST SERVICE ON SFP ONT ................................................................ ................................ ..................................... ..... 24
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 3 of 27
m or f n oi t a d zi n r a o th e s u u a ,t n n et e ti m r u w c t o u d o si ht ht
9.5
CREATE VOIP SERVICE ON SFP ONT ................................................................. ................................ ........................................................... .......................... 24
9.6
CREATE XDSL V VECTORED LINE ................................................................. ................................ ................................................................. ..................................... ..... 25
9.7
CREATE HSI SERVICE (RGW) ............................................................. ............................ .................................................................. .......................................... ......... 25
9.8
CREATE VOD + MULTICAST SERVICE ................................................................. ................................ ........................................................... .......................... 25
i w f o d ing
ite o
e
9.9 CREATE VOIP SERVICE .............................................................. ........................... .................................................................. ..................................................... .................... 25 10 USEFUL SHOW COMMANDS ............................................................................................ 25
y rm p c p t d o n n a st n o n et g in n o s s c a st P i . f d o e vr n oi e t s a er ic st n u h gi m A
ll
r c
o
m
10.1
VIEW VECTOR DISTURBERS ON VDSL2 VECTORING LINES ............................................... ........................................................ ......... 25
10.2
VIEW THE XDSL LINE STATUS ................................................................................................... 25
10.3
SHOW IGMP STATISTICS ................................................................ ............................... ................................................................. .......................................... .......... 26
10.4
SHOW SIP STATISTICS ............................................................... .............................. ................................................................. ............................................... ............... 26
10.5
MIRROR ON OLT ....................................................................................................................... 26
10.6
MIRROR ON MDU ................................................................. ................................ ................................................................ ..................................................... ...................... 26
11
DOCUMENT HISTORY .........................................................................................................27 .......................................................... ...............................................27
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 4 of 27
m or f
1 n oi t a
d zi n r
Preface This document describes the process of configuring a 7356REM ISAM for use in PT Telkom network for the Vectoring Field Trial.
a o th e s u u a t, n n et e ti m r
2
u w c t o u d
Compatibility
o is ht ht i
This document supports the configuration of the 7356REM ISAM with the following w
f o d ing
ite o
e
release:
y rm p
ISAM R5.0 or higher
c p t d o n n a st n
3
o n et g in n o s s c a
The following conventions are used throughout this document: Courier New font: denotes to be entered commands, and their output.
The # prompt denotes login as root;
The > prompt denotes login as normal user.
Bold italics Arial font :
st P i . f d o e vr n
oi e t s a re ci
ts n u h gi m A
ll
r
c
o
m
Conventions
denotes GUI actions (menu selections or buttons).
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 5 of 27
m rof n iot
4 a
d izr n a o th e s
4.1 u
u a t, n n et e u
itr d
u
m
Pre-configuration steps Connect to the 7360FX OLT & 7356REM MDU ISAM via Craft Terminal Connect the PC’s Serial port to the craft port of the 7356REM ISAM (LCMI). The craft port is located on the NRNT-A card.
w c t o o is ht ht i w f
Pin-out of RJ45 connector:
o d ing
ite o
e
y mr p c p t d o
Signal Description
n n a ts n o n et g in n o s s c a st P i . f d o e vr n oi e t s a re ci ts n u h igr m A
ll c
o
m
RI_DSR DCD DTR EG RXD TXD CTS RTS
Data-Set-Ready Data-Carrier-Detect Data-Carrier-Detect Data-Terminal-Ready Data-Terminal-Ready Signal Ground Receive-Data Transmit-Data Clear-To-Send Request-To-Send Request-To-Send
Pin
Type 1 2 3 4 5 6 7 8
O O I Ref O I O I
Open HyperTerminal (or equivalent) and setup the serial connection with following parameters:
As soon as you connect the system will show following prompt: Would you like a CLI(C) or a TL1 login(T) or TL1 normal session(N) ? [N]:
Choose ‘C’ to enter the TL1. The factory username and password are:
Username = isadmin
Password = i$@mad-
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 6 of 27
ans#150”” This password needs to be changed on first logon. Please Ple ase change it to ““ans#150 (without the quotes) m rof n iot a d izr n a o ht e s u u a ,t n n et e u
itr d
u
m w c t o o is thi th w f o d ngi
ite o
e
y mr p c p t d o n n a ts n o n et g ni n o s s c a tsi P . f d o e vr n s
iot st n
e a er ic u h igr m A
ll
m o c
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 7 of 27
m or f n iot
5 a
d izr n a o ht e s
OLT Basic Setup - Initial configuration
5.1 Reset the system with clean database u
u a ,t n n m
tet o
t
e ir
Remove any existing configuration.
u w c u d o
isadmin># admin software-mngt oswp 1 activate clear-db
si thi th w f o d ngi tei o
e
y mr p
Note: The system will reset and come up with an empty database. Follow step 4.1 to Note: The re-connect to the system.
c p t d o n n a ts n o n te g ni n o s s c a tsi P
5.2 Configure uplink ports
. f d o e rv n s
iot st n
e
Configure 1 uplink to connect to the network, port 1 on NT in 1GE mode for connection to Metro-E. a
er ic u h igr m A
ll c
o
m
isadmin># configure port nt-a:xfp:1 ethernet speed 1000 isadmin># configure port nt-a:xfp:1 ethernet autonegotiate limited isadmin># configure port nt-a:xfp:1 no shutdown
Note: The Note: The ports have a MTU of 2000 Bytes configured by default
5.3 Configure management VLAN Assign the management VLAN to Uplink. isadmin># configure service vpls 82 customer 1 v-vpls vlan 82 create isadmin># configure service vpls 82 description "management vlan" isadmin># configure service vpls 82 nt-a:xfp:1:82 create isadmin># configure service vpls 82 no shutdown
part needs to be replaced by the actual actu al value found on the node bold part Note: The bold Note: The information sheet
5.4 Configure System IP address Assign the management IP address and routing table. isadmin># configure system management host-ip-address manual: 172.27.141.56/26 isadmin># configure system management default-route 172.27.141.1
part needs to be replaced by the actual actu al value found on the node Note: The bold Note: The bold part information sheet Note: System Note: System is now reachable from EMS and the network.
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 8 of 27
m or f n oi t
5.5 Configure System ID a
d zi n r a o ht e s
Configure the system name. u
u a ,t n n m
tet o
t
e
isadmin># configure system id 09-TDS-01 ; ir
u w c u d
part needs to be replaced by the actual value found f ound on the node Note: The bold bold part information sheet o
si ht ht i w f o d gin tei o
e
y mr p c p t d
5.6 Configure System Prompt o
n n a st n o n te g
Configure the system prompt to represent the system name and use type based LT numbering.
in n o s s c a st P i . f d o e rv n iot st n
isadmin># configure system security operator isadmin prompt "%s:%n@ AR09-TDS-01 AR09-TDS-01%d%c"
s
e a er ic u h gi m A
ll
r m o c
Note: The bold bold part part needs to be replaced by the actual value found f ound on the node information sheet Note: The total length of the prompt string needs to be less or equal than 28 Note: The characters. This means the system ID can only be 18 characters.
5.7 Configure system login banner Configure the system CLI login banner isadmin># configure system security login-banner " login-banner "Access Access to the ISAM system is for authorized staff only" only " isadmin># configure system security welcome-banner " welcome-banner "AlcatelAlcatelLucent 7360FX OLT" OLT"
5.8 Configure Slot Bandwidth Configure the system slot bandwidth between the switching swit ching matrix and the Line cards (value is speed between line card and each controller) isadmin># configure system max-lt-link-speed link-speed link-speed forty-gb
5.9 Configure Slot Numbering & DHCP Option82 Format Configure the slot numbering format and the DHCP Option82 format isadmin># configure system security profile admin admin slot-numbering slot-numbering type-based type-based port-num-in-proto type-based type-based isadmin># configure system port-num-in-proto isadmin># configure system loop-id-syntax efm-based-pon "Access_Node_ID eth Rack/Frame/Slot/Port/ONU/OnuSlt/UNI" Rack/Frame/Slot/Port/ONU/OnuSlt/UNI"
Note: After setting this slot numbering the operator needs to logout and login again to Note: After activate the new setting
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 9 of 27
5.10 Disable password aging & timeout for operator login m or f n oi
Disable the password aging and session time out for operator login t a
d zi n r a o
isadmin># configure system security profile admin admin passwordtimeout timeout 0 th
e s u u a t, n n et e ti m r u
isadmin># configure system security ssh server-profile idletimeout timeout 300 300 w
c t o u d o is ht ht i w f o d ing ite o
e
y rm p
5.11 Configure the SNMP communities
c p t d o n n a
To allow 5520AMS access, the host-address used is the IP address of the AMS, optionally this can be set to a subnet or 0.0.0.0/0 to allow access to all hosts. st
n o n et g in n o s s c a st P
isadmin># configure system security snmp community community public public hostaddress address 10.153.5.65/32 context context nt nt i
. f d o e vr n oi e t s a re ci
isadmin># configure system security snmp community community NETMAN hostaddress address 10.153.5.65/32 context context shub shub
ts n u h gi m A
ll
r o
m c
The bold Note: The Note: bold part needs to be replaced by the actual value found on the node information sheet sheet
5.12 Save the configuration database save-protected isadmin># admin software-mngt ihub database
5.13 Configure SNTP Configure SNTP server for network time synchronization. isadmin># configure system sntp server-ip-addr server-ip-addr 10.153.5.65 timezone-offset 420 enable 420 enable timezone-offset
actu al value found on the node Note: The Note: The bold part bold part needs to be replaced by the actual information sheet Note: The Note: The NTP server IP points to the AMS Server 5.14 Plan all inserted cards Configure all cards in the system isadmin># configure equipment slot nt-a nt-a planned-type planned-type fant-f fant-f unlock lt:1/1/1 planned-type planned-type nglt-c nglt-c isadmin># configure equipment slot lt:1/1/1 unlock
5.15 Enable PON Ports Enable PON in the system. admin-state up isadmin># configure pon interface 1/1/1/1 1/1/1/1 admin-state isadmin># configure qos interface pon:1/1/1/1 pon:1/1/1/1 ds-num-queue ds-num-queue 8
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 10 of 27
m or f n iot
5.16 Reboot 7360FX OLT a
d izr n a o th e s
Reboot 7360FX OLT u
u a t, n n et e ti
reboot-isam without-self-test without-self-test isadmin># admin equipment reboot-isam
m r u w c t o u d o is ht ht i w f o d ing ite o
e
y mr p c p t d o n n a st n o n et g in n o s s c a st P i . f d o e vr n oi e t s a re ci ts n u h igr m A
ll
m o c
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 11 of 27
m rof
6 n iot a
d izr
MDU Basic Setup - Initial configuration
6.1 Reset the system with clean database
n a o ht e s u u a ,t
Remove any existing configuration. n
n et e u
itr d
u
m w
isadmin># admin software-mngt oswp 1 activate clear-db
c t o o is thi th w f o d ngi ite
Note: The system will reset and come up with an empty database. Follow step 4.1 to Note: The re-connect to the system.
y mr p e o c p t d o n n a ts n o n et g ni n
6.2 Configure uplink ports o
s s c a tsi P . f d o
Configure 1 uplink to connect to the network, port 1 on NT in 1GE mode for connection to OLT.
e vr n s
iot st n
e a er ic u h igr m A
ll c
o
m
isadmin># configure interface shub port nt:sfp:1 port-type network mode 1gbps:full admin-status up
The ports have a MTU of 2000 Bytes configured by default Note: The Note:
6.3 Configure management VLAN Assign the management VLAN to Link Aggregation Group. isadmin># configure system mgnt-vlan-id 82 isadmin># configure system shub entry vlan ext-vlan-id 82 isadmin># configure vlan shub id 82 egress-port nt:sfp:1
bold part part needs to be replaced by the actual actu al value found on the node Note: The bold Note: The information sheet
6.4 Configure System IP address Assign the management IP address and routing table. isadmin># configure system management host-ip-address manual: 127.72.141.57/26 isadmin># configure system management default-route 172.27.141.1
Note: The bold Note: The bold part part needs to be replaced by the actual actu al value found on the node information sheet Note: System Note: System is now reachable from EMS and OLT
6.5 Configure System ID Configure the system name. isadmin># configure system id 09-TDS-01 ;
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 12 of 27
part needs to be replaced by the actual value found on the node Note: The bold bold part information sheet m or f n iot a d izr n a o ht e s u u a ,t
6.6 Configure System Prompt n
n m
tet o
t
e ir u w
Configure the system prompt to represent the system name and use type based LT numbering.
c u d o si thi th w f o d ngi tei
isadmin># configure system security operator isadmin prompt "%s:%n@ 09-TDS-01%d%c"
y mr p e o c p t d o n n a ts n o n te g
Note: The bold part needs to be replaced by the actual value found f ound on the node bold part information sheet
ni n o s s c a tsi P . f d o e rv n iot st n
Note: The total length of the prompt string needs to be less or equal than 28 Note: The characters. This means the system ID can only be 18 characters.
s
e a er ic u h igr m A
ll
m o c
6.7 Configure system login banner Configure the system CLI login banner Access to the isadmin># configure system security login-banner " login-banner "Access ISAM system is for authorized staff only" only " isadmin># configure system security welcome-banner " welcome-banner "AlcatelAlcatelLucent 7356REM MDU" MDU"
6.8 Configure Slot Bandwidth Configure the system slot bandwidth between the switching swit ching matrix and the Line cards (value is speed between line card and each controller) isadmin># configure system max-lt-link-speed link-speed link-speed twodotfive-gb
6.9 Configure Slot Numbering & DHCP Option82 Format Configure the slot numbering format and the DHCP Option82 format isadmin># configure system security profile admin admin slot-numbering slot-numbering type-based type-based port-num-in-proto type-based type-based isadmin># configure system port-num-in-proto isadmin># configure system loop-id-syn loop-id-syntax tax efm-based-d efm-based-dsl sl "Access_Node_ID eth Rack/Frame/Slot/Port Rack/Frame/Slot/Port" "
Note: After setting this slot numbering the operator needs to logout and login again to Note: After activate the new setting 6.10 Disable password aging & timeout for operator login Disable the password aging and session time out for operator login isadmin># configure system security profile admin admin passwordtimeout timeout 0
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 13 of 27
isadmin># configure system security ssh server-profile idletimeout timeout 300 300 m or f n iot a d izr n a o ht e s u u
6.11 Configure the SNMP communities a
,t n n m
tet o
t
e ir u
To allow 5520AMS access , the host-address used is the IP address of the A AMS, MS, optionally this can be set to a subnet or 0.0.0.0/0 to allow access to all hosts. w
c u d o si ht th i w f o d gn i
tei o
e
isadmin># configure system security snmp community community public public hostaddress address 10.153.5.65/32 context context nt nt
y mr p c p t
isadmin># configure system security snmp community community NETMAN hostaddress address 10.153.5.65/32 context context shub shub
d o n n a st n o n te g ni n o s s c a tsi P . f d o e
Note: The bold Note: The bold part needs to be replaced by the actual value found on the node information sheet sheet
rv n s
iot st n
e a er ic u h gi m A
ll
r m c
o
6.12 Save the configuration database save save isadmin># admin software-mngt shub database
6.13 Configure SNTP Configure SNTP server for network time synchronization. isadmin># configure system sntp server-ip-addr server-ip-addr 10.153.5.65 timezone-offset timezone-offset 420 enable 420 enable
actu al value found on the node Note: The bold part Note: The bold part needs to be replaced by the actual information sheet Note: The Note: The NTP server IP points to the AMS Server 6.14 Plan all inserted cards Configure all cards in the system isadmin># configure equipment slot nt-a planned-type nrnt-a unlock isadmin># configure equipment slot lt:1/1/1 lt:1/1/1 planned-type planned-type ndlt-c ndlt-c unlock isadmin># configure equipment slot lt:1/1/2 lt:1/1/2 planned-type planned-type npot-c npot-c unlock
6.15 Reboot ISAM Reboot the 7356REM MDU without-self-test isadmin># admin equipment reboot-isam reboot-isam without-self-test
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 14 of 27
m or f n oi t a d zi n r a o
7
OLT Service Provisioning - Initial configuration
7.1
Create Upstream Bandwidth Profiles (DBA)
th e s u u a t, n n et e ti m r u w c t o u d o is
Create Bandwidth profiles according to the type of service. These profiles regulate the ht
ht i w f o d gn i
tei o
e
DBA bandwidth and priority. isadmin># configure qos profiles bandwidth UP_1G UP_1G committed-inforate 0 assured-info-rate 10000 10000 excessive-info-rate 1000000 1000000 delay-tolerance delay-tolerance 8
y rm p c p t d o n n a st n o n et g in n o s s c a st P i . f d o e vr n oi e t s a
7.2
er ci ts n u h gi m A
ll
r
Create Downstream Shaper Profiles Create Bandwidth profiles according to the type of service. These profiles are used for rate shaping on Line card
m o c
isadmin># configure qos profiles shaper DN_1G DN_1G committed-inforate rate 0 committed-burst-size 0 excess-info-rate excess-info-rate 1000000 1000000 type type singletokenbucketgpon
7.3
Create Pbit to TC Mapping Profiles Create PBit to Traffic Class mapping profiles. isadmin># configure qos profiles ingress-qos Default_TC0 Default_TC0 dot1p0-tc 0 dot1-p1-tc 0 dot1-p2-tc 0 dot1-p3-tc 0 dot1-p4-tc 0 dot1-p5-tc 0 dot1-p6-tc 0 dot1-p7-tc 0 isadmin># configure qos profiles ingress-qos Ingress_Default Ingress_Default dot1-p0-tc 0 dot1-p1-tc 1 dot1-p2-tc 2 dot1-p3-tc 3 dot1-p4-tc 4 dot1-p5-tc 5 dot1-p6-tc 6 dot1-p7-tc 7
7.4
Configure System Multicast for IPTV Enable Multicast on System Level: isadmin># configure igmp system src-ip-address src-ip-address 10.88.43.222 query-interval user-igmp-version 2 netw-igmp-version 2 query-interval 125 start user-igmp-version
Create Multicast VLAN: isadmin># configure vlan id 110 110 mode mode residential-bridge name name IPTV IPTV new-broadcast new-broadcast enable enable in-qos-prof-name in-qos-prof-name name:Default_TC0 name:Default_TC0 isadmin># configure port nt-a:xfp:1 ethernet nt-a:xfp:1 ethernet autonegotiate limited nt-a:xfp:1 ethernet ethernet speed 1000 isadmin># configure port nt-a:xfp:1 isadmin># configure port nt-a:xfp:1 nt-a:xfp:1 no no shutdown isadmin># configure service vpls 110 110 customer customer 1 v-vpls vlan 110 110 create isadmin># configure service vpls 110 110 description "IPTV" description "IPTV" sap nt-a:xfp:1:110 create nt-a:xfp:1:110 create isadmin># configure service vpls 110 110 sap
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 15 of 27
sap nt-a:xfp:1:110 nt-a:xfp:1:110 igmpisadmin># configure service vpls 110 110 sap snooping snooping mrouter-port mrouter-port m or f n oi t a d zi
isadmin># configure service vpls 110 110 sap sap lt:1/1/1:110 create lt:1/1/1:110 create
n r a o th e s u u a
sap lt:1/1/1:110 lt:1/1/1:110 igmpisadmin># configure service vpls 110 110 sap snooping snooping version 2 2
t, n n et e ti m r u w c t o u d
110 sap sap lt:1/1/1:110 lt:1/1/1:110 igmpisadmin># configure service vpls 110 snooping snooping send-queries send-queries o
is ht ht i w f o d gn i
tei o
e
igmp-snooping no shutdown isadmin># configure service vpls 110 110 igmp-snooping no
y mr p c p t
isadmin># configure service vpls 110 no 110 no shutdown
d o n n a st n o n et g in n o s s c a st
Create Multicast Channels:
P i . f d o e vr n
isadmin># configure mcast chn 239.200.10.[1...10] src-ip-addr src-ip-addr 0.0.0.0 vlan-id vlan-id 20 20 guaranteed-serv guaranteed-serv peak-bit-rate peak-bit-rate 8000 8000 0.0.0.0 oi
e t s a re ci ts n u h igr m A
ll
m o c
Note: The Note: The bold bold part part needs to be replaced by the actual value found on the node information sheet. 7.5
Create VLANs Create VLANs on system and assign to all LTs and Uplink HSI VLAN: isadmin># configure vlan id 3210 3210 mode mode residential-bridge name name HSI new-broadcast new-broadcast enable enable HSI isadmin># configure vlan id stacked:1284:10 mode stacked:1284:10 mode residentialbridge bridge name name HSI HSI in-qos-prof-name in-qos-prof-name name: Ingress_Default isadmin># configure service vpls 3210 3210 customer customer 1 v-vpls vlan vlan 3210 3210 create create 3210 description description "HSI" "HSI" isadmin># configure service vpls 3210 isadmin># configure service vpls 3210 3210 sap sap nt-a:xfp:1:3210 nt-a:xfp:1:3210 create create 3210 sap sap lt:1/1/1:3210 lt:1/1/1:3210 create create isadmin># configure service vpls 3210 3210 no no shutdown isadmin># configure service vpls 3210
VoIP (SIP) VLAN: isadmin># configure vlan id 2929 2929 mode mode residential-bridge name name SIP in-qos-prof-name in-qos-prof-name name: Ingress_Default SIP isadmin># configure service vpls 2929 2929 customer customer 1 v-vpls vlan vlan 2898 create create 2898 2929 description description "SIP" "SIP" isadmin># configure service vpls 2929 2929 sap sap nt-a:xfp:1:2929 nt-a:xfp:1:2929 create create isadmin># configure service vpls 2929 isadmin># configure service vpls 2929 2929 sap sap lt:1/1/1:2929 lt:1/1/1:2929 create create 2929 no no shutdown isadmin># configure service vpls 2929
VoD VLAN:
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 16 of 27
111 mode mode residential-bridge name name VoD VoD isadmin># configure vlan id 111 in-qos-prof-name in-qos-prof-name name: Ingress_Default m rof n iot a d izr
isadmin># configure service vpls 111 111 customer customer 1 v-vpls vlan vlan 111 111 create
n a o ht e s u u a t, n n et e itr d
u
isadmin># configure service vpls 111 111 description description "VoD" "VoD"
u
m w c t o
sap nt-a:xfp:1:111 create nt-a:xfp:1:111 create isadmin># configure service vpls 111 111 sap o
is thi ht w f o d ngi itte
isadmin># configure service vpls 111 111 sap sap lt:1/1/1:111 create lt:1/1/1:111 create isadmin># configure service vpls 111 no 111 no shutdown
y mr p e o c p t d o n n a ts n o n et g
Multicast VLAN:
in n o s s c a st P i
110 mode mode residential-bridge name name isadmin># configure vlan id 110 IPTV IPTV in-qos-prof-name in-qos-prof-name name: Ingress_Default
. f d o e vr n s
iot ts n
e a er ci u h igr A
ll
m c
o
m
isadmin># configure service vpls 110 110 customer customer 1 v-vpls vlan vlan 110 110 create 110 description description "IPTV" "IPTV" isadmin># configure service vpls 110 isadmin># configure service vpls 110 110 sap sap nt-a:xfp:1:110 create nt-a:xfp:1:110 create 110 sap sap lt:1/1/1:110 create lt:1/1/1:110 create isadmin># configure service vpls 110 isadmin># configure service vpls 110 no 110 no shutdown
bold part part needs to be replaced by the actual actu al value found on the node Note: The bold Note: The information sheet.
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 17 of 27
m rof n iot a d izr n a
8
MDU Service Provisioning - Initial configuration
8.1
Create Vectoring Control Entity (VCE) Profile and associate it to a board
o ht e s u u a ,t n n m
tet o
t
e ir u w c
A non-null Vectoring Control Entity (VCE) profile should be associated to a board which is capable of processing the vectoring algorithms (Board Level Vectoring (BLV) board). u
d o si thi th w f o d ngi te it
vce-profile 1 name name VCE_DEFAULT VCE_DEFAULT version version isadmin># configure xdsl vce-profile 1 vce-join-timeout 20 active
y mr p e o c p t d o n n a
isadmin># configure xdsl board 1/1/1 vce-profile 1 ts
n o n et g ni n o s s c a tsi P . f
8.2
d o e vr n s
iot st n
e a er
Create xDSL Vectoring Profiles isadmin># configure xdsl vect-profile 1 name VECT_US_DS
ic u h igr m A
ll
isadmin>configure>xdsl>vect-profile>1$ version 1 m o c
isadmin>configure>xdsl>vect-profile>1$ active isadmin>configure>xdsl>vect-profile>1$ exit
8.3
Create xDSL Service Profiles Create xDSL Service Profiles. isadmin># configure xdsl service-profile 1 name MaxUS_MaxDS_SRA_FAST isadmin>configure>xdsl>service-profile>1$ version 1 isadmin>configure>xdsl>service-profile>1$ ra-mode-down dynamic isadmin>configure>xdsl>service-profile>1$ ra-mode-up dynamic isadmin>configure>xdsl>service-profile>1$ min-bitrate-down 32 isadmin>configure>xdsl>service-profile>1$ min-bitrate-up 32 isadmin>configure>xdsl>service-profile>1$ plan-bitrate-down 1024 isadmin>configure>xdsl>service-profile>1$ max-bitrate-down 262140 isadmin>configure>xdsl>service-profile>1$ max-bitrate-up 50000 isadmin>configure>xdsl>service-profile>1$ max-delay-down 2 isadmin>configure>xdsl>service-profile>1$ max-delay-up 2 isadmin>configure>xdsl>service-profile>1$ active isadmin>configure>xdsl>service-profile>1$ exit
8.4
Create xDSL Spectrum Profiles Create xDSL Spectrum Profiles. Profiles. isadmin># configure xdsl spectrum-profile 1 name VDSL2_noUPBO isadmin>configure>xdsl>spectrum-profile>1$ version 1 isadmin>configure>xdsl>spectrum-profile>1$ dis-ansi-t1413 isadmin>configure>xdsl>spectrum-profile>1$ dis-etsi-dts
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 18 of 27
isadmin>configure>xdsl>spectrum-profile>1$ dis-g992-1-a m or f n
isadmin>configure>xdsl>spectrum-profile>1$ dis-g992-1-b o
isadmin>configure>xdsl>spectrum-profile>1$ dis-g992-2-a
a
iot d izr n a ht e s u u a ,t n n tet o
t
isadmin>configure>xdsl>spectrum-profile>1$ dis-g992-3-a
m
e ir u w c
isadmin>configure>xdsl>spectrum-profile>1$ dis-g992-3-b u
d o si ht th i
isadmin>configure>xdsl>spectrum-profile>1$ dis-etsi-ts w
f o d ngi ttei
isadmin>configure>xdsl>spectrum-profile>1$ g993-2-8a
y mr p e o c p t d
isadmin>configure>xdsl>spectrum-profile>1$ g993-2-8b o
n n a st n o n
isadmin>configure>xdsl>spectrum-profile>1$ g993-2-8c te
g ni n o s s c a
isadmin>configure>xdsl>spectrum-profile>1$ g993-2-8d tsi
P . f d o e rv n s
iot
isadmin>configure>xdsl>spectrum-profile>1$ g993-2-12a
st n
isadmin>configure>xdsl>spectrum-profile>1$ g993-2-12b
e a er ic u h gi m A
ll
r c
o
m
isadmin>configure>xdsl>spectrum-profile>1$ g993-2-17a isadmin>configure>xdsl>spectrum-profile>1$ max-noise-down 240 isadmin>configure>xdsl>spectrum-profile>1$ vdsl isadmin>configure>xdsl>spectrum-profile>1>vdsl# annex-b-998ade
vdsl-band-plan
isadmin>configure>xdsl>spectrum-profile>1>vdsl# optional-band up isadmin>configure>xdsl>spectrum-profile>1>vdsl# 138
optional-endfreq
isadmin>configure>xdsl>spectrum-profile>1>vdsl# adsl-band allowadsl isadmin>configure>xdsl>spectrum-profile>1>vdsl# max-band 8 isadmin>configure>xdsl>spectrum-profile>1>vdsl# pbo-mode pbomode-down isadmin>configure>xdsl>spectrum-profile>1>vdsl# pbo 1 isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>1# 4000
param-a
isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>1# exit isadmin>configure>xdsl>spectrum-profile>1>vdsl# pbo 2 isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>2# 4730
param-a
isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>2# 1977
param-b
isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>2# exit isadmin>configure>xdsl>spectrum-profile>1>vdsl# pbo 3 isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>3# 5400
param-a
isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>3# 1577
param-b
isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>3# exit isadmin>configure>xdsl>spectrum-profile>1>vdsl# pbo 4
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 19 of 27
m or f n oi t a d zi n r a o th e s u u a ,t n n et e
isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>4# 5400
param-a
isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>4# 1077
param-b
isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>4# exit ti
m r u w c t o u d
isadmin>configure>xdsl>spectrum-profile>1>vdsl# pbo 5 o
si ht ht i w f o d gn i
ttei o
e
y rm p c p t d o n n a st n o n et g in n o
isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>5# 5400
param-a
isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>5# 943
param-b
isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>5# exit
s s c a st P i . f d
isadmin>configure>xdsl>spectrum-profile>1>vdsl# exit o
e vr n oi e t s a er
isadmin>configure>xdsl>spectrum-profile>1# vdsl2 ic
st n u h gi m A
ll
r c
o
m
isadmin>configure>xdsl>spectrum-profile>1>vdsl2# propr-featvalue 2147483134 isadmin>configure>xdsl>spectrum-profile>1>vdsl2# regionbm2-psd-down
psd-shape-down
isadmin>configure>xdsl>spectrum-profile>1>vdsl2# regionbm2-psd-down
psd-shape-up
isadmin>configure>xdsl>spectrum-profile>1>vdsl2# ab-param
rx-psd-shape-up
isadmin>configure>xdsl>spectrum-profile>1>vdsl2# pbo 1 isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>1# 4000
param-a
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>1# exit isadmin>configure>xdsl>spectrum-profile>1>vdsl2# pbo 2 isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>2# 4730
param-a
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>2# 1977
param-b
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>2# exit isadmin>configure>xdsl>spectrum-profile>1>vdsl2# pbo 3 isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>3# 5400
param-a
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>3# 1577
param-b
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>3# exit isadmin>configure>xdsl>spectrum-profile>1>vdsl2# pbo 4 isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>4# 5400
param-a
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>4# 1077
param-b
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>4# exit isadmin>configure>xdsl>spectrum-profile>1>vdsl2# pbo 5
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 20 of 27
m or f n oi t a d zi n r a o th e s u u a t, n n et e
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>5# 5400
param-a
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>5# 943
param-b
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>5# exit ti
m r u w c t o u d
isadmin>configure>xdsl>spectrum-profile>1>vdsl2# exit o
is ht ht i w f o d gn i
tet o
e
isadmin>configure>xdsl>spectrum-profile>1# active isadmin>configure>xdsl>spectrum-profile>1# exit i
y rm p c p t d o n n a st n o n et
8.5
g in n o s s c a st P i
Create xDSL Rtx Profiles Create xDSL Rtx Profiles.
. f d o e vr n oi e t
isadmin># configure xdsl rtx-profile 1 name ARQUSDS
s a re ci ts n u h
isadmin>configure>xdsl>rtx-profile>1$ version 1
gi m A
ll
r m o c
isadmin>configure>xdsl>rtx-profile>1$ min-exp-thrpt-dn 2000 isadmin>configure>xdsl>rtx-profile>1$ min-exp-thrpt-up 180 isadmin>configure>xdsl>rtx-profile>1$ plan-exp-thrpt-dn 20000 isadmin>configure>xdsl>rtx-profile>1$ plan-exp-thrpt-up 1024 isadmin>configure>xdsl>rtx-profile>1$ max-exp-thrpt-dn 131000 isadmin>configure>xdsl>rtx-profile>1$ max-exp-thrpt-up 50000 isadmin>configure>xdsl>rtx-profile>1$ max-net-rate-dn 131000 isadmin>configure>xdsl>rtx-profile>1$ max-net-rate-up 50000 isadmin>configure>xdsl>rtx-profile>1$ shine-ratio-dn 0 isadmin>configure>xdsl>rtx-profile>1$ shine-ratio-up 0 isadmin>configure>xdsl>rtx-profile>1$ active isadmin>configure>xdsl>rtx-profile>1$ exit
8.6
Configure System Multicast for IPTV Enable Multicast on System Level: isadmin># configure mcast general fast-change isadmin># configure mcast general package-member [1...1024] isadmin># configure igmp system src-ip-address 10.88.43.222 start user-igmp-version 2 netw-igmp-version 2 isadmin># configure igmp shub igs-system start-snooping enablesnooping self-ip-addr-mode configure
Create Multicast VLAN: isadmin># configure vlan shub id 110 mode residential-bridge residential-bridge name IPTV isadmin># configure vlan shub id 110 egress-port lt:1/1/1 isadmin># configure vlan shub id 110 egress-port nt:sfp:1 isadmin># configure vlan id 110 mode residential-bridge name new-broadcast enable new-broadcast IPTV
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 21 of 27
m rof n iot
Create Multicast Channels: o
isadmin># configure qos cac-mode nocac
a d izr n a th e s u u a t, n n
isadmin># configure mcast channel 239.1.1.[1...254] src-ip-addr 0.0.0.0 peak-bit-rate 1000 vlan-id 110 et
e u
itr d
u
m w c t o o is ht
isadmin># configure mcast channel 239.1.2.[1...254] src-ip-addr
ht i w f o d g in
tet o
e
0.0.0.0 peak-bit-rate 1000 vlan-id 110 i
y mr p c p t d o n n a
bold part part needs to be replaced by the actual value found on the node Note: The bold Note: The information sheet. ts
n o n et g in n o s s c a st P i . f d o e vr n
8.7 oi
e t s a re ci ts n u
Create VLANs on system and assign to all LTs and Uplink
h igr m A
ll
Create VLANs
m o c
HSI VLAN: isadmin># configure vlan shub id 3210 mode mode residential-bridge name HSI isadmin># configure vlan shub id 3210 egress-port egress-port lt:1/1/1 lt:1/1/1 egress-port nt:sfp:1 nt:sfp:1 isadmin># configure vlan shub id 3210 egress-port isadmin># configure vlan id 3210 mode mode residential-bridge residential-bridge name name broadcast-frames HSI broadcast-frames
VoD VLAN: mode residential-bridge isadmin># configure vlan shub id 111 mode name VoD user2-comm disable isadmin># configure vlan shub id 111 egress-port egress-port lt:1/1/1 lt:1/1/1 egress-port nt:sfp:1 nt:sfp:1 isadmin># configure vlan shub id 111 egress-port isadmin># configure vlan id 111 mode mode residential-bridge name name VoD VoD broadcast-frames broadcast-frames
Voice VLAN: isadmin># configure vlan shub id 2929 mode mode voice-vlan voice-vlan name name SIP isadmin># configure vlan shub id 2929 egress-port egress-port lt:1/1/1 lt:1/1/1 egress-port nt:sfp:1 isadmin># configure vlan shub id 2929 egress-port
Note: The bold part Note: The bold part needs to be replaced by the actual actu al value found on the node information sheet.
8.8
Create VOIP Service Create Voice(SIP) Service for connection to the softswitch. isadmin># configure voice sip server sip1 address ipv4:10.0.0.110 admin-domain-name vsp1 admin-status up
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 22 of 27
isadmin># configure voice sip lineid-syn-prof profile1 potssyntax random m rof n iot a d izr
isadmin># configure voice sip user-agent ua_01 ip-config-mode dhcp ip-addr-policy distributed signal-vlan-id 2929 rtp-vlan-id 2929 admin-status up
n a o ht e s u u a ,t n n et e u
itr d
u
m w c
isadmin># configure voice sip transport udp provider-name vsp1 admin-status up t
o o is thi th w f o d g ni
tet o
e
isadmin># configure voice sip register vsp1 register-uri telkom.net.id i
y mr p c p t d o n
isadmin># configure voice sip vsp vsp1 domain-name 10.0.0.110 n
a ts n o n et g
isadmin># configure voice sip vsp vsp1 admin-status up
ni n o s s c a tsi P
isadmin># configure voice sip user-agent-ap ua_01 slot-id lt:1/1/2 admin-status up
. f d o e vr n s
iot st n
e a er ic
isadmin># configure voice sip dialplan dp1 u
h igr A
ll
m c
o
m
isadmin># configure configure voice sip digitmap dp1 type regular rule x.T isadmin># configure voice sip redundancy vsp1
bg-monitor-int bg-monitor- int 0
isadmin># configure voice sip system session-timer admin-status up
Note: The bold Note: The bold part part needs to be replaced by the actual actu al value found on the node information sheet.
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 23 of 27
m or f n iot a d
9
Service Provisioning Sample Service Configuration
9.1
Create SFP ONT Infrastructure
–
izr n a o ht e s u u a ,t n n m
tet o
t
e ir u
Create ONTs using SLID Password. w
c u d o si thi th
1/1/1/1/1 sw-verisadmin># configure equipment ont interface 1/1/1/1/1 w
f o d g ni
ttei o
e
pland 3FE55040AOPA21 pland 3FE55040AOPA21 sernum sernum ALCL: FAB00CAC FAB00CAC fec-up enable enable enableaes enable aes enable
y mr p c p t d
isadmin># configure equipment ont slot 1/1/1/1/1/1 1/1/1/1/1/1 planned-cardtype type 10_100base 10_100base plndnumdataports plndnumdataports 1 plndnumvoiceports 0 port-type port-type nni admin-state admin-state up up o
n n a ts n o n te g ni n o s s c a tsi P . f
us-num-queue 8 isadmin># configure qos interface ont:1/1/1/1/1 ont:1/1/1/1/1 us-num-queue
d o e rv n s
iot st n
e
isadmin># configure interface port uni:1/1/1/1/1/1/1 no admin-up a
er ic u h igr
isadmin># configure qos interface ont:1/1/1/1/1 ont:1/1/1/1/1 scheduler-node scheduler-node name:NGLT_Default m
A
ll
m o c
9.2
Configure SFP ONT UNI isadmin># configure interface port uni:1/1/1/1/1/1/1 admin-up isadmin># configure qos interface 1/1/1/1/1/1/1 1/1/1/1/1/1/1 scheduler-node scheduler-node name:NGLT_Default isadmin># configure qos interface 1/1/1/1/1/1/1 cac-profile cac-profile name:FD_GponVideo isadmin># configure qos interface 1/1/1/1/1/1/1 interface 1/1/1/1/1/1/1 upstream-queue upstream-queue [0...7] weight weight 0 0 bandwidth-profile bandwidth-profile UP_1G UP_1G bandwidth-sharing ontsharing isadmin># configure qos interface 1/1/1/1/1/1/1 queue queue [0…7] priority 1 priority 1 weight weight 1 1 isadmin># configure bridge port /1/1/1/1/1/1 /1/1/1/1/1/1 max-unicast-mac max-unicast-mac 2048
9.3
Create HSI Service on SFP ONT Create HSI service on port 1 using HSI VLAN. vlan-id 3210 3210 tag isadmin># configure bridge port 1/1/1/1/1/1/1 1/1/1/1/1/1/1 vlan-id single-tagged single-tagged network-vla network-vlan n 3210 3210 vlan-scope vlan-scope local local
9.4
Create VOD + Multicast Service on SFP ONT Create VOD + Multicast Service using VOD VLAN. isadmin># configure bridge port 1/1/1/1/1/1/1 1/1/1/1/1/1/1 vlan-id vlan-id 111 111 tag tag single-tagged single-tagged network-vlan network-vlan 111 111 vlan-scope vlan-scope local local isadmin># configure igmp channel vlan:1/1/1/1/1/1/1:110 max-numgroup group 1024 max-msg-rate max-msg-rate 256 256
9.5
Create VoIP Service on SFP ONT Create VOIP services
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 24 of 27
vlan-id 2929 2929 tag isadmin># configure bridge port 1/1/1/1/1/1/1 1/1/1/1/1/1/1 vlan-id single-tagged single-tagged network-vla network-vlan n 2929 2929 vlan-scope vlan-scope local local m or f n oi t a d zi n r a o ht e s u u
9.6 a
,t n n m
tet o
t
e ir u
Create xDSL Vectored Line Create xDSL Vectored Line.
w c u d o si ht
isadmin># configure xdsl line 1/1/1/1 1/1/1/1 service-profile 1
ht i w f o d g in
ttei o
e
spectrum-profile 1 rtx-profile 1 vect-profile 1 carrier-datamode mode on on transfer-mode transfer-mode ptm ptm admin-up admin-up
y mr p c p t d o n n a st n o n
9.7 te
g in n o s s c a st
Create HSI service
P i . f d o e rv n iot st n
max-unicast-mac 16 16 isadmin># configure bridge port 1/1/1/1 1/1/1/1 max-unicast-mac
s
e a er ic
vlan-id 3210 3210 tag tag singleisadmin># configure bridge port 1/1/1/1 1/1/1/1 vlan-id tagged tagged u
h gi m r A
ll
Create HSI Service (RGW)
m o c
pvid 3210 3210 isadmin># configure bridge port 1/1/1/1 1/1/1/1 pvid
9.8
Create VOD + Multicast Service Create VOD +Multicast service isadmin># configure bridge port 1/1/1/1 1/1/1/1 max-unicast-mac max-unicast-mac 16 16 vlan-id 111 tag tag singleisadmin># configure bridge port 1/1/1/1 1/1/1/1 vlan-id tagged tagged vlan:1/1/1/1 1/1/1/1: :110 110 max-num-group max-num-group isadmin># configure igmp channel vlan: 16 16
9.9
Create VoIP Service Create VoIP service 1/1/2/1 directoryisadmin># configure voice sip termination 1/1/2/1 number number +623151511024 +623151511024 user-name user-name
[email protected] uri uri md5-realm telkom.net.id telkom.net.id md5-password md5-password
[email protected] md5-realm plain:telkom135 admin-status plain:telkom135 admin-status up up 1/1/2/2 directoryisadmin># configure voice sip termination 1/1/2/2 number number +623151511025 +623151511025 user-name user-name
[email protected] uri uri
[email protected] md5-realm md5-realm telkom.net.id telkom.net.id md5-password md5-password plain:telkom135 admin-status up up plain:telkom135 admin-status
10 Useful Show Commands
10.1 View vector disturbers on VDSL2 vectoring lines
View the actual mapping between the VP board board and the SLV LT boards.
isadmin># show xdsl vect-disturbers 1/1/1/1 max-reported-dist max-reported-dist 48 48
10.2 View the xDSL line status status View the xDSL line st status atus.
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 25 of 27
isadmin># show xdsl operational-data line m or f n oi t a d zi n r a o
View the mode of vectoring supported on CPE. th
e s u u a t, n n
isadmin># show xdsl operational-data near-end line 1/1/1/1 1/1/1/1 detail et
e ti m r u w c t o u d o is ht ht i w f o g in
tedt o
e
10.3 Show IGMP Statistics i
y rm p c p
Show IGMP statistics. t
d o n n a st n
isadmin># show igmp channel counter
o n et g in n o s
isadmin># show igmp channel miscellaneous
s c a st P i . f d o e vr n oi e t s a re
10.4 Show SIP Statistics ci
ts n u h gi m A
ll
r c
o
m
Show SIP statistics.
isadmin># show voice sip server isadmin># show voice sip user-agent-ap isadmin># show voice sip termination
10.5 Mirror on OLT Mirroring on OLT.
isadmin># configure port nt-a:eth:1 ethernet autonegotiate limited isadmin># configure port nt-a:eth:1 no shutdown nt-a:xfp:1 egress ingress isadmin># debug mirror-source 1 port nt-a:xfp:1 egress isadmin># debug mirror-source 1 no shutdown isadmin># configure mirror mirror-dest 1 sap nt-a:eth:1:0 nt-a:eth:1:0 isadmin># configure mirror mirror-dest 1 isadmin># info configure mirror isadmin># show debug
10.6 Mirror on MDU Mirroring on MDU.
isadmin># configure interface shub port nt:eth:1 port-type nt:eth:1 port-type network admin-status auto-up isadmin># configure interface shub mirror enable to-port nt:sfp:2 nt:sfp:2 isadmin># configure interface shub mirror port nt:sfp:1 external nt:sfp:1 external ingress egress isadmin># configure interface shub mirror port nt:sfp:1 internal nt:sfp:1 internal ingress egress isadmin># info configure interface shub mirror
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 26 of 27
11 Document History m or f n iot a
d izr n a o th e s u u a t, n n
Version
Date
Author(s)
Description/Comment Description/Comment
0.1
June 24th 2014
Fiona Tay
Document Creation
et e ti m r u w c t o u d o is ht ht i w f o g in
tedt o
e
i y mr p c p t d o n n a st n o n et g in n o s s c a st P i . f d o e vr n oi e t s a re ci ts n u h igr m A
ll
m o c
- END OF DOCUMENT -
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 27 of 27
