Nokia Flexi Multiradio 10 Base Station Product Description
February 23, 2017 | Author: Do Dinh Ly | Category: N/A
Short Description
Download Nokia Flexi Multiradio 10 Base Station Product Description...
Description
Nokia Networks
WCDMA RAN, Rel. RU50 and RU50 EP1, Operating Documentation, Issue 03 Flexi Multiradio 10 Base Station Product Description DN0971928 Issue 01G Approval Date 2014-08-20
Flexi Multiradio 10 Base Station Product Description
The information in this document applies solely to the hardware/software product (“Product”) specified herein, and only as specified herein. This document is intended for use by Nokia Solutions and Networks' customers (“You”) only, and it may not be used except for the purposes defined in the agreement between You and Nokia Solutions and Networks (“Agreement”) under which this document is distributed. No part of this document may be used, copied, reproduced, modified or transmitted in any form or means without the prior written permission of Nokia Solutions and Networks. If you have not entered into an Agreement applicable to the Product, or if that Agreement has expired or has been terminated, You may not use this document in any manner and You are obliged to return it to Nokia Solutions and Networks and destroy or delete any copies thereof. The document has been prepared to be used by professional and properly trained personnel, and You assume full responsibility when using it. Nokia Solutions and Networks welcome Your comments as part of the process of continuous development and improvement of the documentation. This document and its contents are provided as a convenience to You. Any information or statements concerning the suitability, capacity, fitness for purpose or performance of the Product are given solely on an “as is” and “as available” basis in this document, and Nokia Solutions and Networks reserves the right to change any such information and statements without notice. Nokia Solutions Networks has made all reasonable efforts to ensure that the content of this document is adequate and free of material errors and omissions, and Nokia Solutions and Networks will correct errors that You identify in this document. But, Nokia Solutions and Networks' total liability for any errors in the document is strictly limited to the correction of such error(s). Nokia Solutions and Networks does not warrant that the use of the software in the Product will be uninterrupted or error-free. NO WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY OF AVAILABILITY, ACCURACY, RELIABILITY, TITLE, NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS MADE IN RELATION TO THE CONTENT OF THIS DOCUMENT. IN NO EVENT WILL NOKIA SOLUTIONS AND NETWORKS BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT, EVEN IN THE CASE OF ERRORS IN OR OMISSIONS FROM THIS DOCUMENT OR ITS CONTENT. This document is Nokia Solutions and Networks’ proprietary and confidential information, which may not be distributed or disclosed to any third parties without the prior written consent of Nokia Solutions and Networks. Nokia is a registered trademark of Nokia Corporation. Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for identification purposes only. Copyright © 2014 Nokia Solutions and Networks. All rights reserved.
f
Important Notice on Product Safety This product may present safety risks due to laser, electricity, heat, and other sources of danger. Only trained and qualified personnel may install, operate, maintain or otherwise handle this product and only after having carefully read the safety information applicable to this product. The safety information is provided in the Safety Information section in the “Legal, Safety and Environmental Information” part of this document or documentation set.
Nokia Solutions and Networks is continually striving to reduce the adverse environmental effects of its products and services. We would like to encourage you as our customers and users to join us in working towards a cleaner, safer environment. Please recycle product packaging and follow the recommendations for power use and proper disposal of our products and their components. If you should have questions regarding our Environmental Policy or any of the environmental services we offer, please contact us at Nokia Solutions and Networks for any additional information.
2
DN0971928
Issue: 01G
Flexi Multiradio 10 Base Station Product Description
Table of Contents This document has 47 pages
Issue: 01G
1
Summary of changes..................................................................... 6
2 2.1 2.2
Introduction to Flexi Multiradio 10 Base Station.............................8 Construction................................................................................... 9 Mechanics.................................................................................... 10
3
RSS-310 compliance....................................................................11
4
EU RoHS statement.....................................................................12
5
CE marking.................................................................................. 13
6
FCC Part 15 compliance.............................................................. 14
7 7.1 7.2 7.3
Benefits........................................................................................ 15 Cost-efficient modular site............................................................15 One BTS for all network applications........................................... 18 Feederless and Distributed Site concept..................................... 19
8 8.1 8.2
Single RAN aspects..................................................................... 20 RF sharing....................................................................................20 Transport backhaul sharing .........................................................22
9
Baseband capacity.......................................................................25
10 10.1 10.2 10.2.1 10.2.1.1 10.3 10.4 10.5
Management and software...........................................................26 Local management.......................................................................26 Remote management ..................................................................27 Remote User Event Log Management ........................................27 RUEM concept - how does it work?............................................. 28 Configuration management..........................................................29 Software updates......................................................................... 29 External alarms and controls........................................................30
11 11.1 11.2 11.3 11.4 11.5 11.6
Modules........................................................................................31 System Module............................................................................ 31 RF Module....................................................................................31 Remote Radio Head.....................................................................32 Active Antenna ............................................................................ 32 Optional items.............................................................................. 32 External interfaces....................................................................... 36
12
Appendix Flexi abbreviations....................................................... 37
13
Appendix Flexi BTS hardware releases....................................... 40
DN0971928
3
Flexi Multiradio 10 Base Station Product Description
List of Figures
4
Figure 1
General architecture of Flexi Multiradio 10 Base Station .................... 9
Figure 2
List of countries respecting EU Directive 1999/5/EC..........................13
Figure 3
Principle of Intelligent Shut-Down in the case of transmission node site...................................................................................................... 17
Figure 4
GSM-LTE RF sharing architecture overview...................................... 20
Figure 5
WCDMA-GSM RF sharing architecture overview...............................21
Figure 6
WCDMA-LTE RF sharing architecture overview................................ 22
Figure 7
Transport sharing in multiradio BTS site.............................................23
Figure 8
BTS Site Manager main window........................................................ 26
Figure 9
Audit trail.............................................................................................27
Figure 10
The RUEM concept............................................................................ 28
DN0971928
Issue: 01G
Flexi Multiradio 10 Base Station Product Description
List of Tables
Issue: 01G
Table 1
RAT releases covered by the document...............................................6
Table 2
Maximum capacity of Flexi Multiradio 10 Base Station...................... 25
Table 3
Flexi BTS naming convention.............................................................37
Table 4
Flexi Multiradio BTS System Module hardware product generations.40
Table 5
Flexi Multiradio BTS RF Module hardware product generations........ 40
Table 6
Flexi Multiradio BTS Remote Radio Head hardware product generations.........................................................................................45
DN0971928
5
Summary of changes
Flexi Multiradio 10 Base Station Product Description
1 Summary of changes Changes between document issues are cumulative. Therefore, the latest document issue contains all changes made to previous issues. This document is common for all Radio Access Technologies (RAT). You may find here information about solutions that are not available or supported in a specific SW release or RAT. Table RAT releases covered by the document lists all SW releases covered by the content of this document. For features supported in your SW release, see respective feature documentation chapter in the system library. Table 1
RAT releases covered by the document
Radio Access Technology (RAT)
Product release
GSM
RG20, RG30
LTE
RL25TD, RL35TD, RL45TD RL40, RL50, RL60
WCDMA
RU40, RU50
Changes between issues 01F (2014-06-05) and 01G (2014-08-20) RF Module •
Information on 6 x 60 W RF Module has been added.
Appendix Flexi BTS hardware releases •
Information on FRGY, FHGA, FHGB, FHEF, FHFB, FXCE, and FXED has been added.
Changes between issues 01E (2014-02-27) and 01F (2014-06-05) Transport backhaul sharing •
The list of available synchronization options has been added.
Remote management •
Information on higher level service management products has been added.
Baseband capacity •
Capacity values of FSMF in WCDMA mode have been updated in Table 2: Maximum capacity of Flexi Multiradio 10 Base Station.
Changes between issues 01D (2013-12-05) and 01E (2014-02-27) Cost-efficient modular site • • •
Section Low site rental costs has been added. Section Low total site power consumption has been added. Section SW-defined BTS has been added.
Construction
6
DN0971928
Issue: 01G
Flexi Multiradio 10 Base Station Product Description
•
Summary of changes
Information on outdoor and indoor variants has been added.
Local management •
Microsoft Windows 8 has been added to the list of supported systems.
Remote management •
This section has been added.
Baseband capacity •
Table 2: Maximum capacity of Flexi Multiradio 10 Base Station has been updated with information on FSIH.
Appendix Flexi abbreviations •
Information on indoor version of System Module has been added.
System Module •
FSIH has been added to the list of available System Modules.
Optional items • •
Information on extension sub-module (FBBC) has been added. Information on extension sub-module (FBIH) has been added.
Appendix Flexi BTS hardware releases • • •
Issue: 01G
Information on FSIH, FRPK, and FHEC has been added. FXCB, FXFC, and FXFB are supported in RL60. Information on FRGV has been removed.
DN0971928
7
Introduction to Flexi Multiradio 10 Base Station
Flexi Multiradio 10 Base Station Product Description
2 Introduction to Flexi Multiradio 10 Base Station This Product Description describes Flexi Multiradio 10 Base Station, which is based on Flexi Multiradio System Module and multiradio-capable RF Module/Remote Radio Head variants. Flexi Multiradio 10 Base Station is a high-capacity, Single RAN, and LTEAdvanced ready multiradio BTS. It supports the following radio access technologies in all needed frequency variants: • • • •
GSM/EDGE WCDMA HSPA and HSPA evolution LTE TDD/FDD
The architecture supports 3GPP functions and features in 3GPP release 9 and beyond, providing a future-proof platform for advanced radio systems. Furthermore, the architecture supports the most common interfaces between the modules and functions as defined by Open Base Station Architecture Initiative (OBSAI) and Common Public Radio Interface (CPRI).
w
NOTICE: See roadmaps for CPRI availability. Flexi Multiradio 10 Base Station is a true software-defined multiradio and multicarrier base station that can use all the above mentioned network technologies. The concurrent mode functionality can include several radio access technologies and their combinations, for example GSM-LTE, GSM-WCDMA, WCDMA-LTE, GSM-WCDMA-LTE. The Flexi BTS also supports multi-operator cases (MOCN), where several operators can share resources of one BTS. Flexi Multiradio 10 Base Station supports legacy network interface. It also fully utilizes Ethernet-based transport with security solutions, synchronization and timing methods based on synchronous Ethernet, timing over packet, and GPS methods.
8
DN0971928
Issue: 01G
Flexi Multiradio 10 Base Station Product Description
Figure 1
Introduction to Flexi Multiradio 10 Base Station
General architecture of Flexi Multiradio 10 Base Station
See the following documents for more information on Flexi Multiradio 10 Base Station modules and sub-modules: • • • •
Flexi Multiradio 10 Base Station System Module Description Flexi Multiradio BTS Radio Module and Remote Radio Head Description Flexi Multiradio 10 Base Station Transmission Description Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description
2.1 Construction There are two variants of Flexi Multiradio 10 BTS - outdoor/indoor (rated at IP65) and indoor (rated at IP20).
Outdoor/indoor variant A typical BTS consists of the following baseband items: • • • •
Issue: 01G
one Flexi Multiradio 10 BTS System Module with an integrated Gigabit Ethernet (GE) transport interface (FSMF) one optional Flexi Multiradio 10 BTS Transmission Sub-Module (FTIF or FPFM200i) one or two optional Flexi Multiradio 10 BTS Capacity Extension Sub-Modules (FBBA or FBBC) one optional Flexi Multiradio 10 BTS Power Distribution Sub-Module (FPFD)
DN0971928
9
Introduction to Flexi Multiradio 10 Base Station
•
Flexi Multiradio 10 Base Station Product Description
one optional outdoor-capable Flexi Power Module (FPMA) that can house AC/DC converter sub-modules (FPAA) and battery sub-modules (FPBA/B)
When the modules are installed without a cabinet, the following items are available: • •
Flexi 3U Mounting Covers front/back for each module for installations without a cabinet (FMCA), mandatory in outdoor installations. Flexi Mounting Kit Floor/Wall/Pole for stacked installations (FMFA). (A minimum of one plinth for a stack installation and one plinth per two modules in pole and wall installations.)
Indoor variant A typical BTS consists of the following baseband items: • • •
one Flexi Multiradio 10 BTS System Module with integrated Gigabit Ethernet (GE) transport interfaces (FSIH) one or two optional Flexi Multiradio 10 BTS Capacity Extension Sub-Modules (FBIH) one optional outdoor-capable Flexi Power Module (FPMA) that can house AC/DC converter sub-modules (FPAA) and battery sub-modules (FPBA/B)
When the modules are installed without a cabinet, the following item is available: •
Flexi Mounting Kit Floor/Wall/Pole for stacked installations (FMFA). (A minimum of one plinth for a stack installation and one plinth per two modules in pole and wall installations.)
2.2 Mechanics Flexi Multiradio 10 BTS modules consist of the following main parts: •
•
•
• • • • •
10
Module core. The core mechanics, with installed gaskets in all of the connectors, shield the module core against solid foreign objects, and make the module core IP65 weatherproof (outdoor variant) or IP20 (indoor variant). The core mechanics also provide EMC shielding. Module casing. This provides fixing points for modules to the plinth and supports the stack of modules. The module core can be changed even if the module is at the bottom of the module stack. Fan assembly. This provides fresh air to cool the module. Each module controls its own fans according to temperature information, and two redundant fans enable module operation at normal temperatures, even with one fan. The fan sub-module can be changed in an operational module at a site where back access is provided. Module cables. All cables are IP65 protected. Optional Front and Back covers (FMCA) for BTS site installations without a cabinet. or Optional Flexi Cabinet for Outdoor (FCOA) or Flexi Cabinet for Indoor (FCIA) or Optional Mounting Shield (FMSA/FMSB) or Optional Flexi Cabinet Outdoor Small (FCOS)
DN0971928
Issue: 01G
Flexi Multiradio 10 Base Station Product Description
RSS-310 compliance
3 RSS-310 compliance This equipment complies with RSS-310 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference.
Issue: 01G
DN0971928
11
EU RoHS statement
Flexi Multiradio 10 Base Station Product Description
4 EU RoHS statement This equipment complies with the European Union RoHS Directive 2011/65/EU on the restriction of the use of certain hazardous substances in electrical and electronic equipment. The directive applies to the use of lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (PBB), and polybrominated diphenyl ethers (PBDE) in electrical and electronic equipment.
12
DN0971928
Issue: 01G
Flexi Multiradio 10 Base Station Product Description
CE marking
5 CE marking Declaration of Conformity with Regard to the EU Directive 1999/5/EC (R&TTE Directive) Hereby, NSN declares that this equipment is in compliance with the essential requirements and other relevant provisions of Directive: 1999/5/EC. Figure 2
List of countries respecting EU Directive 1999/5/EC
R&TTEDirective1995/5/EC AT
ü
FR
ü
LV
ü
LI
ü
BE
ü
DE
ü
LT
ü
RO
ü
BG
ü
GB
ü
LU
ü
SK
ü
CY
ü
GR
ü
MT
ü
SI
ü
CZ
ü
HU
ü
NL
ü
ES
ü
DK
ü
IS
ü
NO
ü
SE
ü
EE
ü
IE
ü
PL
ü
CH
ü
FI
ü
IT
ü
PT
ü
TR
ü
This declaration is only valid for configurations (combinations of software, firmware, and hardware) provided and/or supported by NSN.
Issue: 01G
DN0971928
13
FCC Part 15 compliance
Flexi Multiradio 10 Base Station Product Description
6 FCC Part 15 compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manuals, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Changes or modifications not expressly approved by the party responsible for compliance could void the user´s authority to operate the equipment.
14
DN0971928
Issue: 01G
Flexi Multiradio 10 Base Station Product Description
Benefits
7 Benefits 7.1 Cost-efficient modular site With Flexi Multiradio 10 Base Station, the same equipment can be used to build coverage and capacity. A high cell capacity and wide coverage per site means fewer sites which makes building a network more cost-effective. Flexi Multiradio 10 Base Station can be installed at any existing legacy GSM/EDGE/CDMA/WCDMA site for a broadband data capability upgrade. Flexi Multiradio 10 Base Station is designed to utilize the existing site equipment.
Low site rental costs Flexi Multiradio 10 Base Station reduces BTS site rental costs because a BTS-specific cabinet or extra floor space is no longer needed on the site. However, existing site support and auxiliary cabinets can be used to house Flexi Multiradio 10 BTS modules. The modules can be also installed on a wall.
Low total site power consumption Because of the high integration of Flexi Multiradio 10 BTS and the advanced power amplifiers the overall power consumption is decreased. In typical configurations, the power saving is up to 60% compared to the first generation of WCDMA BTS. Additional benefits are: • • • • • •
smaller battery capacity for the same backup time less AC-DC rectifiers smaller fuses and thinner power feeding cables air-conditioning for indoor sites needed only in special cases no air-conditioning for outdoor sites no need for a dedicated cabinet for the power system and auxiliary equipment
Easy installation A Flexi Multiradio 10 Base Station module can be lifted, carried, and put in place by one person. The average module installation time is reduced, compared to traditional cabinet BTSs. Flexi Multiradio 10 Base Station can be installed on a wall, poll, or floor. It fits in the existing legacy GSM/EDGE/CDMA/WCDMA BTS footprints as well. Flexi Multiradio 10 BTS outdoor is protected to at least IP65 level and can be installed as such at an outdoor site. In addition, both indoor and outdoor cabinet installation options are available. Installation locations for a Flexi Multiradio 10 Base Station can be smaller than or the same as those reserved for previous BTSs.
SW-defined BTS Flexi Multiradio 10 Base Station can be SW-configured according to requirements of a given radio technology - GSM/EDGE, WCDMA/HSPA+, or LTE (TD/FDD). Additionally, many SW-definable features can be activated by the software. For example: • •
Issue: 01G
sector activation (one, two, or three sectors active of a 3-sector RF Module) RF power mode for active sector (8, 20, 40, 60, or 80 W)
DN0971928
15
Benefits
Flexi Multiradio 10 Base Station Product Description
• • • • • • • •
g
LTE cell bandwidth (1.4, 3, 5, 10, 15, or 20 MHz) MHA support and control Antenna Tilt support and control dual band and multiband support four-way uplink diversity mode 4TX MIMO downlink mode transport interface synchronization method (for example, GPS, timing over packet)
The full feature list for each RAT can be found in Feature List document.
Low acoustic noise The acoustic noise produced by a Flexi Multiradio 10 Base Station site is low because of reduced power consumption and an increased unit integration level. Site acceptance is easier, especially at urban outdoor sites. Fan speeds and acoustic noise are adapted to the BTS load and ambient temperature.
Easy commissioning The autodetection feature of Flexi Multiradio 10 Base Station makes commissioning and integrating fast and easy. The commissioning wizard guides the user step-by-step through the whole commissioning process. At the end of the process, the commissioning wizard produces a BTS Commissioning Report.
Reliable operation Simplicity and speed of maintenance improves operational reliability. Maintenance is improved by module integration and automatic fault detection procedures. Special attention has been paid to Flexi Multiradio 10 Base Station software start time, reducing, for instance, downtime when a new software package is put into use.
Intelligent shut-down Intelligent shut-down feature optimizes the investment to one battery backup system on a high-capacity BTS, especially on sites that operate as important transmission hub nodes. With intelligent shut-down, separate backup systems for BTS and transmission are unnecessary. Flexi Multiradio 10 BTS with battery backup system supports an intelligent BTS site power shutdown procedure in the event of an AC power failure. During the commissioning of each site, the operator can define different shutdown timers and priorities for the BTS sectors and carriers. Intelligent shutdown is activated from Power systems by activating one external alarm (EAC) lines to Flexi BTS. When Flexi BTS detects a problem with the power provisioning - so switching to battery power supply - an alarm is raised, and the BTS automatically reduces the required power consumption. As a result, Flexi BTS is operating with reduced or no service offered as long as there is enough power. Once the AC power is restored, Flexi BTS again offers full service. The reduction of power is done via the stepwise shutdown of services which are triggered by operator configurable timers per BTS. Different shutdown scenarios can be configured for the BTS by setting these timers.
16
DN0971928
Issue: 01G
Flexi Multiradio 10 Base Station Product Description
Benefits
Two timers with two different actions are steering the BTS behavior while working on batteries: • •
When the first timer is exceeded, selected number of cells will be switched off (for example 222 to 111) When the second timer is exceeded, all cells of that BTS will be switched off gracefully, means the UEs in that cell will be forced to change to a different cell.
The timer values can be configured via NetActTM or with BTS Site Manager. The setting especially of the first timer value shall consider the specific situation in the network. For example, a three-sector two-carrier Flexi Multiradio 10 BTS WCDMA (2+2+2) site equipped with battery backup operates as a transmission hub node towards other BTSs in a chain. The first timer can be set to shut down the second carriers of the BTS, to operate as 1+1+1 (for example) 30 minutes after an AC power failure. The second timer can be set to shut down the remaining 1+1+1 BTS (for example) one hour after the AC power failure, in order to support the transmission node for as long as possible with the existing battery capacity. Timers can be set according to the configuration and priorities of each site. Figure 3
Principle of Intelligent Shut-Down in the case of transmission node site RF Module
1st timer expires: shut down sectors or carriers in BTS RF Module
RF Module 2nd timer expires: shut down BTS, keep transmission operational System Module backhaul BTS1 external alarm line
DC AC power failure triggers shut down start timers via alarm line
AC power
Rectifier AC-DC Battery back-up DC Transmission HUB node to other BTSs
w
Issue: 01G
backhaul BTS2
NOTICE: See roadmaps for intelligent shut-down availability.
DN0971928
17
Benefits
Flexi Multiradio 10 Base Station Product Description
7.2 One BTS for all network applications Flexi Multiradio 10 Base Station is optimized for high-capacity and wide-coverage applications. It ensures cell ranges that meet the requirements of the coverage applications. Therefore, the number of sites required for building a good coverage is minimized. A seamless voice and data coverage area can be built easily. Flexi Multiradio 10 Base Station has been developed for coverage applications. It offers: • • • • • •
w
Wide variety of RF modules for different applications and use cases, for example high downlink power with Flexi 3-sector 240 W RF Module. Support of 2TX MIMO 40+40 W per sector with single 6TX RF Module and 4TX MIMO 40+40+40+40 W per sector with two 6TX RF Modules. Optimum uplink performance and receiver sensitivity. Outdoor modules that can be located close to antennas, reducing antenna feeder losses. Optimized antenna system performance, including 3GPP antenna tilting and masthead amplifier (MHA) support. High downlink power in small size with Flexi Remote Radio Head.
NOTICE: Masthead amplifier (MHA) is not supported in TD-LTE.
Antenna line Optimized Antenna line is a separate, optional site solution to additionally improve total BTS and antenna system site RF performance and to minimize costs. Flexi Multiradio 10 Base Station Optimized Antenna line includes the following optional features, enabled by SW licenses: • • •
Integrated MHA power feeding and O&M control to the RF Module of the Flexi BTS. Integrated Antenna line supervision by Return Loss measurement (VSWR measurement). Integrated 3GPP standard Antenna Tilt power feeding and 3GPP Antenna Tilt O&M control to the RF Module of the Flexi BTS.
Flexi RF Module has an integrated lightning protection circuit in all antenna connectors. The antenna connector of Flexi Multiradio 10 Base Station is on the RF Module front panel. No additional units, connectors, or jumper cables are necessary between the Flexi Multiradio 10 Base Station antenna connector and the antenna. That minimizes the antenna line length and losses, as well as optimizes RF performance in both the uplink and downlink direction.
High speed broadband data and high capacity voice Flexi Multiradio 10 Base Station is a compact multi-purpose BTS designed to support all future high speed broadband data and voice services over an air interface. Smooth data and voice capacity evolution is provided through software. The processing capacity of Flexi Multiradio 10 Base Station can be configured to support the maximum capacity that the air interface allows.
18
DN0971928
Issue: 01G
Flexi Multiradio 10 Base Station Product Description
Benefits
In addition to the flexible traffic capacity, Flexi Multiradio 10 Base Station also allows a free mix of traffic patterns to accommodate whatever proportion of voice and data is required. Depending on network capacity requirements, the capacity installed can be matched with the capacity of the air interface.
7.3 Feederless and Distributed Site concept Standard Flexi Multiradio 10 Base Station modules support the Feederless BTS site application where one RF Module or Remote Radio Head or the entire Flexi BTS is installed close to the antennas. For a feederless site, traditional long antenna feeders or masthead amplifiers are not needed thanks to which the BTS site RF performance is optimized in both uplink and downlink. The benefits of Feederless sites are: • • • • • •
Better RF performance because there are no downlink and uplink feeder losses. Easier installation because of reduced cabling to the tower. No long antenna feeders (typically six for a three-sector site). No masthead amplifiers/tower-mounted amplifiers. Reduced total wind load and weight. Reduced total power consumption.
RF Module and Remote Radio Head can be software-activated and configured to support one, two, or three sectors, or one sector with 2TX MIMO with optional four-way uplink diversity. In the Distributed Site solution, RF Module(s) or Remote Radio Head(s) are located up to 20 km away from the main Flexi System Module site.
Issue: 01G
DN0971928
19
Single RAN aspects
Flexi Multiradio 10 Base Station Product Description
8 Single RAN aspects 8.1 RF sharing The RF sharing feature allows Flexi Multiradio BTS RF Module to operate in a concurrent mode with two radio access technologies (RATs). BTS resources between RATs are allocated and shared by allowing two Flexi EDGE/WCDMA/LTE System Modules to share the same Flexi BTS Multiradio RF Module or Remote Radio Head (RRH). RF Module or RRH is transmitting RF carrier signals for two or more RATs at the same frequency band. The RF Sharing concept simplifies the antenna system complexity, and provides the operators with future-proof BTS site evolution. Figure 4
GSM-LTE RF sharing architecture overview LTEmanagement
GSMmanagement
NetAct iOMS NWI3 Q3/XML
BTSO&M S1/IP
FlexiBSC OMU Abis TDM/IP
eNB
BCF FlexiMultiradio BTSGSM
RP3-01
FlexiMultiradio BTSLTE
RP3-01
RFM
20
RP3-01
RFM
DN0971928
RFM
Issue: 01G
Flexi Multiradio 10 Base Station Product Description
Figure 5
Single RAN aspects
WCDMA-GSM RF sharing architecture overview WCDMA management
GSMmanagement
NetAct OMS NWI3 Q3/XML BTSO&M
FlexiBSC
RNC
OMU Iub/BTSO&M
Abis TDM/IP
BCF FlexiMultiradio BTSGSM
RP3-01
FlexiMultiradio BTSWCDMA
RP3-01
RFM
Issue: 01G
RP3-01
RFM
DN0971928
RFM
21
Single RAN aspects
Flexi Multiradio 10 Base Station Product Description
Figure 6
WCDMA-LTE RF sharing architecture overview WCDMA management
LTEmanagement
NetAct iOMS
OMS NWI3
NWI3 BTSO&M
BTSO&M S1/IP
RNC
Iub/BTSO&M
eNB FlexiMultiradio BTSLTE
RP3-01
FlexiMultiradio BTSWCDMA RP3-01
RP3-01
RFM
RFM
For more information, see: • • • • • • • •
RF Sharing Operability Configuring and Upgrading GSM-LTE RF Sharing Creating RF Sharing LTE-GSM Configurations Configuring WCDMA-GSM RF Sharing Creating RF Sharing WCDMA-GSM Configurations Configuring WCDMA-LTE RF Sharing Creating RF Sharing WCDMA-LTE Configurations Flexi Multiradio BTS RF Sharing Supported Configurations (Excel)
8.2 Transport backhaul sharing Transport backhaul sharing provides the possibility for a Single RAN site to be connected to the backhaul network with just one physical Ethernet connection. Note that multiple Flexi Multiradio 10 BTS System Modules are required.
22
DN0971928
Issue: 01G
Flexi Multiradio 10 Base Station Product Description
Figure 7
Single RAN aspects
Transport sharing in multiradio BTS site
SAE-GW MME
RNC
BSC Iub
S1/X2
Packet Abis
System Module LTE
S1/X2
IP
System Module WCDMA
Iub
IP
System Module GSM
Packet Abis
IP
Ethernet
IP Ethernet
IP / Ethernet
Multiradio BTS site
The BTS site backhaul traffic can be aggregated on one integrated IP/Ethernet interface by utilizing integrated QoS aware Ethernet switching. Synchronization Hub feature can be used for reference clock distribution on the BTS site.
QoS Aware Ethernet Switching QoS Aware Ethernet Switching allows multiple Ethernet interfaces in the BTS to be connected through the integrated Ethernet switch. One of the interfaces is used for the backhaul connection, while others might be used to connect other BTSs (at the same or another site). It is also possible to daisy chain several network devices. The Ethernet switch is VLAN- and QoS-aware. The egress traffic of the switch can be shaped to meet the bandwidth limitations of the backhaul network. Additionally, a policy can be applied to the ingress traffic to protect the BTS from the interface overload.
g
Ethernet switching is required at the BTS where the layer 2 traffic aggregation/daisy chain is to be implemented.
Synchronization Hub Each System Module can act as a synchronization hub for other near-located System Modules. For example, it can output 2.048 MHz SynchOut based on any available synchronization source. If PDH interfaces are available in the System Module, then they can also be used for synchronization distribution to other devices.
Issue: 01G
DN0971928
23
Single RAN aspects
Flexi Multiradio 10 Base Station Product Description
If the BTS loses all sync sources, it switches to hold-over mode. Then, the BTS Oven Controlled Crystal Oscillator (OCXO) keeps running with the last known control value, and still provides the sync output. System Module can use the following synchronization methods: • •
the TDM-based network interface the packet network via: – –
• • • •
Timing over Packet Synchronous Ethernet
the 2.048 MHz signal another Flexi BTS or a legacy BTS the Global Positioning System (GPS) the Global Navigation Satellite System (GLONASS)
For more detailed information on the System Module, see Flexi Multiradio 10 Base Station System Module Description.
24
DN0971928
Issue: 01G
Flexi Multiradio 10 Base Station Product Description
Baseband capacity
9 Baseband capacity Baseband capacity by SW license Future-proof Flexi Multiradio System Module capacity is designed to support flexible and cost-optimized site capacity evolution. The highest capacity Flexi System Module is dimensioned to provide a hardware baseband capacity, for example, for up to three 20 MHz LTE cells with 2x2 MIMO (FSMF). Baseband capacity of Flexi Multiradio 10 Base Station can be optimized depending on the BTS configuration and required traffic capacity of the BTS site. More baseband capacity can be allocated remotely from NetAct™ by sending a Baseband SW License to Flexi Multiradio 10 Base Station. Flexi Multiradio 10 Base Station baseband capacity can be optimized in steps of Mbit/s without a site visit.
Future capacity evolution Flexi Multiradio 10 Base Station is future-proof designed to support future capacity demand. The Flexi BTS architecture supports baseband pooling of two System Modules, making it possible to build high capacity sites. Flexi Multiradio System Module provides space for up to two baseband extension sub-modules that triples the capacity of the Flexi Multiradio System Module. SRIO and OBSAI RP3-01 interfaces provide connectivity for baseband capacity and/or technology extension. Baseband extension and related interface utilization depends on the radio access technology and the use case (a pure new Flexi Multiradio System Module case or an existing Flexi System Module case). Table 2: Maximum capacity of Flexi Multiradio 10 Base Station shows radio access technology–specific capacity details. Table 2
Maximum capacity of Flexi Multiradio 10 Base Station
RAT
FSMF
FSIH
GSM/EDGE
36 transceivers (FSMF)
N/A
WCDMA
2.27 Gbps downlink and 417 Mbps uplink (two FSMFs each with two FBBAs)
N/A
LTE
900 Mbps downlink and 300 Mbps uplink (FSMF with one FBBA/FBBC)
TD-LTE only: 3 cells @ 20 MHz 8TX and 8RX or 3 cells @ 20 MHz 4TX and 4 RX or 4 cells @ 20 MHz with 2TX and 2RX
For information on licensing, see Commissioning Flexi Multiradio BTS [technology].
Issue: 01G
DN0971928
25
Management and software
Flexi Multiradio 10 Base Station Product Description
10 Management and software 10.1 Local management The BTS Site Manager software is used to manage Flexi Multiradio 10 Base Station commissioning, supervision, maintenance, and testing, as well as transmission configuration. Figure 8
BTS Site Manager main window
The site manager software package includes the following: • • •
Flexi Multiradio BTS Manager, including antenna line and antenna equipment control and management; FlexiTransport Manager, for transmission management; Site Support Manager, for power and battery backup system.
These managers are integrated so that the physical interface (cable and connectors) is the same in all three cases, however, three different applications run on the PC. The PC is connected to the BTS through an Ethernet connection.
26
DN0971928
Issue: 01G
Flexi Multiradio 10 Base Station Product Description
Management and software
BTS Site Manager runs in the following environments: • • •
Microsoft Windows XP, Vista, 7, 8 (32/64 bits) Microsoft Windows Server 2003 and 2008 Red Hat Enterprise Linux 4 ES GNOME desktop
10.2 Remote management NSN provides an industry-unique NetActTM Network Management System (NMS) platform that fully integrates with GSM, WCDMA, LTE, and transmission networks. One graphical user interface covers the entire network - radio, core, and mobile backhaul. Personnel trained to operate NetActTM can manage the network with small effort. Operators who already have NetActTM can include LTE in the same NMS and thus fully capitalize on their investment in the state-of-the-art NMS. Flexi Multiradio 10 BTS, like the entire RAN, can be managed through NetActTM. The advanced monitoring functions of NetActTM make it possible to minimize management tasks that need to be carried out on the site. NetActTM incorporates a full range of functions, from fault, performance, and configuration management to transmission, trouble, and security management. The BTS site power and backup system can also be monitored. NSN also provides other higher level service management products, such as Service Quality Manager, Serve atOnce Activation Manager, iSON Manager and Operations on Demand. For more information, see NetActTM documentation available in NSN Online Services (NOLS), Product Information Center (PIC).
10.2.1 Remote User Event Log Management Remote User Event Log Management (RUEM) is a feature that allows a network management system (NMS) to trace operations done in network elements (NEs) by different users. This functionality is sometimes called “Audit Trail”. User access and operations might be successful or fail. In both cases this is logged. Figure 9
Issue: 01G
Audit trail
DN0971928
27
Management and software
Flexi Multiradio 10 Base Station Product Description
With RUEM, operations are logged on Flexi Baseband Controller (FCT) and sent to NetActTM within one single RUEM log file. NWI3 logged operations: • • • •
Login attempts (successful and unsuccessful) Logout Configuration changes (on fragment level) Local account updates
HTTP logged operations: • •
Reboot operations Reset to factory default operation
XoH logged operations: • • • • • • • •
10.2.1.1
SW Management (SW update Request and SW interrupt) Object Configuration Management (for example ResetRequest) Licence Update/Deletion Request Alarm Management and Diagnostics (for example Change Direct Access Status) Test Management (for example Test Dedicated State Request) User Management (for example Login and Modify User Request) Commissioning (for example Parse Commissioning Data Request) Clock Operation Request
RUEM concept - how does it work? RUEM correlates every management operation with each user: • •
NWI3 and XOH management operations implement session concept (username/password) HTTP operations which are logged are operations that require username/password
Figure 10
28
The RUEM concept
DN0971928
Issue: 01G
Flexi Multiradio 10 Base Station Product Description
Management and software
Notification - Watermark Operations that are logged by RUEM are stored in FCT in a ring buffer (internally). This buffer is filled up for each logged operation. As soon as a critical value (that is watermark, ~70% of total buffer size) is reached, FCT will send a notification to NetActTM (mediated by OMS in Flexi).
The RUEM upload mechanism 1. Triggered by NetActTM
2. Triggered by Network element (FCT) - if the Watermark level is reached
After a successful reading of the logfile by the NMS, the read logfile is deleted from the BTS to free memory space for next log entries. Log files in the BTS are kept in nonvolatile memory, and thus data is not lost upon power breaks. Exception: In case NetActTM still does not upload the RUEM log file, the buffer might fill up to its maximum size and even exceed this. In the latter situation the buffer has an overflow and some old information gets lost permanently. It is not recoverable. This special event is called a wrapped-over event. This should be logged in RUEM log file.
10.3 Configuration management Once the BTS is in normal operation, a polling process is used to check possible changes in the BTS configuration. When modules are added to or removed from the BTS, the information in the hardware database changes.
10.4 Software updates Flexi Multiradio 10 Base Station can store two software packages in its memory. The software can be loaded either locally, with the BTS Site Manager software, or remotely from NetActTM. Site visits are unnecessary for routine operation and maintenance (O&M) tasks.
Issue: 01G
DN0971928
29
Management and software
Flexi Multiradio 10 Base Station Product Description
Typically, local software download is done only when the NetActTM connection is missing, for example, during the commissioning process. Flexi Multiradio 10 Base Station software can be downloaded as a background operation without interrupting the BTS operation. The new software can be activated at any time. Reboot is required in order to put the software into use. Flexi Multiradio 10 Base Station only uses downloadable software. All software can be downloaded and updated from NetActTM. This procedure is centralized, meaning that several BTSs can be upgraded with the new software either simultaneously or one by one. Flexi Multiradio 10 Base Station keeps the current and previous software packages in its flash memory. Either of these software versions can be activated at any time. A reboot is required in order to put the software into use. Updated software (current and previous) in the BTS can be seen through BTS Site Manager/NetActTM. The RF Module and RRH SW is updated automatically during Flexi Multiradio 10 Base Station SW update.
10.5 External alarms and controls BTS inputs and outputs can be configured and tested locally at the BTS site with Flexi Multiradio BTS Site Manager software. Six user-defined external inputs and six usercontrolled inputs/outputs are available and can be freely configured to support various observation or control needs at the BTS site. In normal operation, the external alarms and control outputs of the BTS are managed from NetActTM after they have been configured.
30
DN0971928
Issue: 01G
Flexi Multiradio 10 Base Station Product Description
Modules
11 Modules 11.1 System Module Flexi Multiradio System Module is fully OBSAI-compatible and has all the control and baseband functions for the supported radio access technologies. System Module can be used in stack, pole, and wall installations, indoors or outdoors. The architecture of Flexi Multiradio System Module enables utilization of several System Module and sub-module variants. The System Module consists of a casing with the following baseband modules: a core module and up to two optional capacity extension sub-modules. Additionally, some variants can be enhanced with optional power distribution and transmission sub-modules. The following Flexi Multiradio System Modules are available: • •
FSMF - high capacity GSM/WCDMA/LTE System Module (indoor/outdoor) FSIH - high capacity TD-LTE System Module (indoor)
For more detailed information on the System Module, see Flexi Multiradio 10 Base Station System Module Description.
11.2 RF Module There are different types of RF Modules available. RF Modules can be used in stack, pole, and wall installations, indoors or outdoors. They can be easily installed outdoors close to antennas. RF Module can support up to three sectors with the following features: • • • • •
high output power at antenna connectors: 3TX 3x60 W, 3TX 3x80 W, 6TX 6x40 W, 6TX 6x60 W six linear power amplifiers six RF filters for TX/RX two-way RX diversity wide bandwidth support: – – – –
• • • •
up to six GSM carriers with 400 kHz minimum carrier separation up to four WCDMA carriers with 3.8 MHz minimum carrier separation LTE signal with 1.4 MHz, 3 MHz, 5 MHz, 10 MHz, 15 MHz, and 20 MHz carrier bandwidth Multi RAT operation with combination of GSM, WCDMA, and LTE
48 V DC power input efficient fans several OBSAI links, each supporting either 32 "slots" (3Gbps) or 64 "slots" (6Gbps) low total wind load and weight
Note that some variants might not be available in all releases. For more detailed information on the RF Modules, see Flexi Multiradio BTS Radio Module and Remote Radio Head Description.
Issue: 01G
DN0971928
31
Modules
Flexi Multiradio 10 Base Station Product Description
11.3 Remote Radio Head There are different types of Remote Radio Heads available (1TX/2RX, 2TX/2RX). Remote Radio Heads are mainly used in outdoor pole installations where support for one sector is needed. The Remote Radio Head (RRH) can support one sector with the following integrated features: • • • • • • • •
high output power at antenna connectors two linear power amplifiers two RF filters for TX/RX two-way RX diversity wide bandwidth support (up to 35 MHz depending on 3GPP band RF variant) a 48 V DC input power supply no fans two OBSAI optical interfaces
For more detailed information on a particular Remote Radio Head, see Flexi Multiradio BTS Radio Module and Remote Radio Head Description.
11.4 Active Antenna Flexi Multiradio Active Antenna is an alternative to RF Modules/Remote Radio Heads. It can also be used in combination with the traditional Flexi RF units. The radio frequency elements of the BTS are integrated into the antenna. Flexi Multiradio Active Antenna increases site capacity and coverage with features such as vertical beamforming, 2x2 Multiple Input Multiple Output (MIMO) and independent TX and RX electrical tilting per frequency or RAT. For more information on Active Antenna, see Flexi Multiradio Antenna System Product Description.
w
NOTICE: See roadmaps for Active Antenna availability.
11.5 Optional items Flexi Multiradio 10 BTS Outdoor Capacity Extension Sub-Module (FBBA) Flexi Multiradio 10 BTS Outdoor Capacity Extension Sub-Module (FBBA) provides additional capacity to the BTS. One FBBA brings additional 576 CEs for WCDMA. HSPA performance is 756 Mbps for downlink and 157 Mbps for uplink. When dedicated for LTE (FDD or TDD), it supports capacity of 3x20 MHz (or 6x10 MHz) with MIMO enabling 450 Mbps downlink and 150 Mbps uplink data speeds. Up to two FBBAs are supported per one Flexi Multiradio System Module.
32
DN0971928
Issue: 01G
Flexi Multiradio 10 Base Station Product Description
Modules
Flexi Multiradio 10 BTS Outdoor Capacity Extension Sub-Module (FBBC) FBBC is a high capacity extension sub-module for Flexi Multiradio 10 BTS (FSMF). It increases both baseband capacity and RF connectivity of Flexi Multiradio 10 BTS System Module. BTS equipped with two FBBC sub-modules provides up to twelve optical RP3-01 6 Gbit/s connections towards RF units. FBBC provides the same baseband capacity as FBBA. Up to two FBBCs are supported per one Flexi Multiradio System Module.
Flexi Multiradio 10 BTS Indoor Capacity Extension Sub-Module (FBIH) FBIH is a high capacity extension sub-module for Flexi Multiradio 10 BTS (indoor). It increases both baseband capacity and RF connectivity of Flexi Multiradio 10 BTS System Module. It supports capacity of 3x20 MHz 8T8R with beamforming.
Flexi Multiradio 10 BTS Transmission Sub-Module (FTIF) Flexi Multiradio 10 BTS Transmission Sub-Module (FTIF) has eight E1/T1/JT1 interfaces and two Gigabit Ethernet Combo ports. Internal connections between the core module and FTIF go through an internal connector.
FlexiPacket FirstMile 200i (FPFM200i) FPFM200i is an NSN FlexiPacket Microwave Radio indoor unit that is designed to fit the transport slot of Flexi Multiradio 10 Base Station System Module. The mechanical integration includes powering of the FPFM200i. The FPFM200i provides support in the Ethernet uplink and downlink traffic. It provides advanced Ethernet processing features, as well as maximum flexibility to support TDM traffic via circuit emulation. The FPFM200i can be connected to Microwave Radio Outdoor units via a single Ethernet cable, using a copper Ethernet port with power feeding support. Alternatively, two cables can be used, in which case one of them is a separate power supply cable. The FPFM200i can be configured, monitored, and administered by a web-based Local Craft Terminal (WebLCT) or NetViewer management tool. That can be done locally or remotely, via Data Communication Network (DCN). For more information, see FlexiPacket FirstMile 200i documentation.
Flexi Multiradio 10 BTS Power Distribution Sub-Module (FPFD) The optional integrated outdoor Flexi Power Distribution Sub-Module (FPFD) is a sizeoptimized power distribution unit that has basic overvoltage protection (type approval level with 2 kV/1 kV). It is designed to be used for stacked configurations, but it can also be used for distributed BTS configurations in the same way as the existing Flexi BTS integrated power distribution sub-module with an optional FSEC or FSES. It is installed inside an outdoor 3U casing, and internal connections between the core module and FPFD go through an internal connector. The FPFD provides four external 48 V DC outputs for Flexi Modules (RF Module, RRH, and extension System Module) or any standard 48 V DC device at the site. FPFD also powers the core module.
Issue: 01G
DN0971928
33
Modules
Flexi Multiradio 10 Base Station Product Description
Flexi Power Distribution Module (FPFC) The optional Flexi Power Distribution Module (FPFC) is a stand-alone, general-purpose outdoor PDU module with Class II overvoltage protection with a 15 kA protection level. It feeds 48 V DC power to distributed Flexi RF Modules or Remote Radio Heads without an external protection unit (FSEC or FSES) when the FPFC is installed close to an RF Module (maximum 4 m away). It is a stand-alone external 19-inch wide 2U high outdoor module. The FPFC provides six outputs for Flexi Modules (RF Modules, RRHs, and extension System Module) or any standard -48 V DC device at the site. It can also be used, for example, up in the tower to divide one main DC line to several RFM/RRHs. It has one external alarm to indicate OVP condition.
Flexi Power Module (FPMA) Flexi Power Module (FPMA) includes an AC connection box, DC cable set, and a support frame for the actual power sub-modules (FPAA and FPBA/B).
Flexi Power AC/DC Sub-Module (FPAA) The main function of Flexi Power AC/DC Sub-Module (FPAA) is to provide the BTS modules with 48 V DC power from an AC supply. The FPMA can house up to four AC/DC rectifiers, each of them having an output power of 1 kW 48 V DC.
Flexi Power Battery Sub-Module (FPBA/B) Flexi Power Battery Sub-Module (FPBA/B) is a separate optional sub-module used together with the AC/DC Module (FPAA). The FPMA can house up to three battery submodules. When the AC power mains is down on a Flexi BTS site, battery backup time is up to 30 minutes for a typical 1+1+1 configuration when three new FPBA/Bs are in use.
Flexi Power DC/DC Module 24V (FPDA) The function of Flexi Power DC/DC Module 24 V (FPDA) is to generate BTS internal 48 V DC power from an external 24 V DC supply. The FPDA is a stand-alone 2 kW DC/DC converter with 2U height.
Flexi Power Rectifier (FPRx) Flexi Power Rectifier (FPRx) is a modular 6 kW output power AC rectifier package made up of three individual 2 kW AC/DC power modules operating in a parallel mode configuration. The FPRx outputs a positive earthed –54 V DC (V48N) as a respective BTS operational supply voltage rail and for site battery charging. It supports Flexi BTS Multiradio configurations (indoor and outdoor cabinets, and stack, pole and wall configurations).
Flexi Cabinet for Outdoor (FCOA) Flexi Cabinet for Outdoor (FCOA) is an optional sales item for new sites where a cabinet is needed. The multipurpose cabinet includes a lock and a door alarm switch that is connected to the System Module EAC connector. The outdoor cabinet can also be used in indoor locations where a locked cabinet for the BTS and other site equipment is needed. The FCOA provides IP65 weather protection.
34
DN0971928
Issue: 01G
Flexi Multiradio 10 Base Station Product Description
Modules
The optional outdoor cabinet can include the following optional items: • • • • • • •
w
Outdoor Site Support Module (FCSA) Flexi Power Rectifier (FPRx) Air filter (FCFA) Fire detector (FCDA) EAC IP55 connection box (FSEB) OVP IP55 connection box (FSEC) OVP IP65 connection box (FSES)
NOTICE: FSEC is not supported in TD-LTE.
Flexi Cabinet for Indoor (FCIA) Flexi Cabinet for Indoor (FCIA) is an optional sales item for new indoor sites where a cabinet is needed. The optional indoor cabinet can include the following optional items: • • • • •
w
Flexi Power Rectifier (FPRx) Fire detector (FCDA) EAC IP55 connection box (FSEB) OVP IP55 connection box (FSEC) OVP IP65 connection box (FSES)
NOTICE: FSEC is not supported in TD-LTE.
Flexi Mounting Shield (FMSA/FMSB) Flexi Mounting Shield is a cabinet solution for the Flexi BTS. The FMSA provides IP65 weather protection for two 3U modules and the FMSB for six 3U modules. Flexi Mounting Kit for Floor, Wall and Pole (FMFA). An optional plinth is used to fix Flexi modules to floor, wall, or pole.
Flexi Cabinet Outdoor Small (FCOS) Flexi Cabinet Outdoor Small (FCOS) is an IP55-rated outdoor cabinet that provides space of 8U for installing IP20-rated units. The following are installation options for Flexi Cabinet Outdoor Small (FCOS): • • • • • •
Stand-alone floor installation On top of a Flexi BTS module stack Wall installation Pole installation Inside Flexi Cabinet for Outdoor (FCOA) 19-inch rack installation
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Mounting Kit for Floor, Wall and Pole (FMFA) is an optional item that is used for installing Flexi modules on the floor, wall, or pole.
Issue: 01G
DN0971928
35
Modules
Flexi Multiradio 10 Base Station Product Description
Flexi System External Alarm (FSEB) Flexi System External Alarm (FSEB) is used as an external alarm control (EAC). In indoor or stacked applications without a cabinet, the enclosure is attached in the proximity of the modules, for example, on a wall. In outdoor applications, it is installed on the outdoor cabinet roof. The FSEB enclosure provides an IP55 weather-protected space for external alarms and controls. Furthermore, it provides power for the fire detector (FCDA).
Flexi System External OVP (FSEC/FSES) Flexi System External OVP (FSEC/FSES) protects Flexi Multiradio modules against surge pulse(s) in power feeding lines. It is also used for altering the DC cable diameter.
11.6 External interfaces For full description of the System Module interfaces, see System Module interfaces in Flexi Multiradio 10 Base Station System Module Description. For full description of the RF Module/RRH interfaces, see RF Module interfaces and Remote Radio Head interfaces in Flexi Multiradio BTS Radio Module and Remote Radio Head Description. For full description of the transmission interfaces, see Flexi Multiradio 10 Base Station Transmission Description.
36
DN0971928
Issue: 01G
Flexi Multiradio 10 Base Station Product Description
Appendix Flexi abbreviations
12 Appendix Flexi abbreviations The naming of the Flexi BTS family has the following format - Fxxx. Table 3: Flexi BTS naming convention shows the explanation of the format.
g Table 3
Table 3: Flexi BTS naming convention might not list all the possible variants/items. Additionally, some items might not be available in certain releases.
Flexi BTS naming convention
Letter
Description
First letter
Flexi family
F _ _ _
Second letter
Antenna Equipment and Same Band Combiner
_ A _ _
The general naming is FAxy, where x indicates: •
A - 400 MHz
•
B - 700 MHz upper
•
C - 850 MHz
•
D - 900 MHz
•
E - 1800 MHz and 1700 MHz
•
F - 1900 MHz
•
G - 2100 MHz
•
H - 2600 MHz
•
J - 2000 MHz
_ B _ _
Baseband Extension Modules
_ C _ _
Cabinet and Cabinet Accessories The general naming is FCxy, where x indicates: •
I - indoor version
•
O - outdoor version
_ C _ _
Repeater Interface Modules
_ D _ _
Diplexers
_ L _ _
Low-noise Mast Head Amplifiers
_ M _ _
Mounting Kits
_ O _ _
Optical distribution unit
_ P _ _
Power supply modules and sub-modules or installation kits
Issue: 01G
DN0971928
37
Appendix Flexi abbreviations
Table 3
Flexi Multiradio 10 Base Station Product Description
Flexi BTS naming convention (Cont.)
Letter
Description
_ H _ _
Radio Modules/Remote Radio Heads
_ R _ _
The general naming is:
_ X _ _
•
FHx_ - Flexi Remote Radio Head
_ Z _ _
•
FRx_ - Flexi RF Module
•
FXx_ - Flexi RF Multiradio
•
FZx_ - Flexi TD-LTE RF Module
Where x indicates:
_ S _ _
•
A - 400 MHz
•
B - 700 MHz upper
•
C - 850 MHz
•
D - 900 MHz
•
E - 1800 MHz and 1700 MHz
•
F - 1900 MHz
•
G - 2100 MHz
•
H - 2600 MHz
•
I - 1700 Mhz and 2100 MHz
•
J - 2000 MHz
•
K - 1500 MHz
•
L - 700 MHz lower
•
M - 800 MHz EU
•
N - 2300 MHz
System Modules The general naming of the System Modules is FSxy, where x indicates: •
I - indoor version
•
M - outdoor version
y indicates: •
B, C, D, E - Flexi Multiradio BTS
•
F, H - Flexi Multiradio 10 BTS
Flexi System External Alarm, Flexi System External OVP The general naming of the modules is FSEx, where x indicates: •
B - Flexi System External Alarm
•
C,S - Flexi System External OVP
_ T _ _
Transport modules, sub-modules and cables.
_ I _ _
The general naming of the transport modules is Fxyz, where: •
38
x indicates either outdoor (T) or indoor (I) version of the Flexi Multiradio System Module.
DN0971928
Issue: 01G
Flexi Multiradio 10 Base Station Product Description
Table 3
Letter
Flexi BTS naming convention (Cont.)
Description •
•
_ Y _ _
Appendix Flexi abbreviations
y indicates the module and interface type, for example: –
P - PDH module with 8 E1/T1/J1 interfaces.
–
I - Hybrid module with PDH symmetrical and Ethernet interfaces.
–
J - Hybrid module with PDH asymmetrical and Ethernet interfaces.
–
O - Optical interface module with STM1/OC3 interface.
–
F - MWR IDU module with FlexBus interfaces.
z indicates the module version: –
A, B, C… - Flexi Multiradio BTS transport sub-modules.
–
F, G… - Flexi Multiradio 10 BTS transport sub-modules.
Global Navigation Satellite System (GNSS) receiver Flexi GPS Surge Protection Kit
Third letter
Application, usage, or frequency band (for example, RF Module, RRH, AAS, Mast Head Amplifiers).
_ _ x _
Fourth letter
Indicates the version - A is the first one, B, C... - the next ones.
_ _ _ x
Issue: 01G
DN0971928
39
Appendix Flexi BTS hardware releases
Flexi Multiradio 10 Base Station Product Description
13 Appendix Flexi BTS hardware releases Table 4
Flexi Multiradio BTS System Module hardware product generations
Module variant
Release 1 HW
Release 2 HW
Release 3 HW
WCDMA release
LTE release
GSM release
FSMB
x
-
-
RAS06
N/A
N/A
FSMC
-
x
-
RU20 on top
N/A
N/A
FSMD
-
x
-
RU10
RL30
N/A
FSME
-
x
-
RU10
RL10
N/A
FSMF
-
-
x
RU30 on top (WN7.0 3.0)
RL25
RG30 EP1
RL40
RU40 on top (WN8.0 2.0) FSIH
Table 5
40
-
-
x
N/A
RL45
N/A
Flexi Multiradio BTS RF Module hardware product generations
Module variant
Abbreviat Release 1 Release 2 Release 3 WCDMA ion HW HW HW release
LTE release
GSM release
Flexi RF Module 850 Dual 50 W
FRCA
x
-
-
RAS5.1
N/A
N/A
Flexi RF Module 850 Single 50 W
FRCB
x
-
-
RAS5.1
N/A
N/A
Flexi RF Module 900 Dual 50 W
FRDA
x
-
-
RAS5.1
N/A
N/A
Flexi RF Module 900 Single 50 W
FRDB
x
-
-
RAS5.1
N/A
N/A
Flexi RF FRFA Module 1900 Dual 50 W
x
-
-
RAS5.1
N/A
N/A
DN0971928
Issue: 01G
Flexi Multiradio 10 Base Station Product Description
Table 5
Flexi Multiradio BTS RF Module hardware product generations (Cont.)
Module variant
Abbreviat Release 1 Release 2 Release 3 WCDMA ion HW HW HW release
LTE release
GSM release
Flexi RF Module 1900 Single 50 W
FRFB
x
-
-
RAS5.1
N/A
N/A
Flexi RF FRGC Module 2100 Dual 50 W
x
-
-
RAS05
N/A
N/A
Flexi RF Module 2100 Single 50 W
x
-
-
RAS05
N/A
N/A
Flexi FRGI Compact RF Module 2.1 Single 40 W
x
-
-
RAS5.1
N/A
N/A
Flexi RF FRGJ Module 2100 Dual 50 W
x
-
-
RAS06
N/A
N/A
Flexi RF Module 2100 Single 50 W
FRGK
x
-
-
RAS06
N/A
N/A
Flexi RF FRGL Module 2100 Dual 50 W
x
-
-
RAS06
N/A
N/A
Flexi RF Module 2100 Single 50 W
x
-
-
RAS06
N/A
N/A
x
-
-
RAS05
N/A
N/A
FRGD
FRGM
Flexi RF FRIA Module 1.7/2.1 Dual 50 W
Issue: 01G
Appendix Flexi BTS hardware releases
DN0971928
41
Appendix Flexi BTS hardware releases
Table 5
42
Flexi Multiradio 10 Base Station Product Description
Flexi Multiradio BTS RF Module hardware product generations (Cont.)
Module variant
Abbreviat Release 1 Release 2 Release 3 WCDMA ion HW HW HW release
LTE release
GSM release
Flexi RF Module 1.7/2.1 Single 50 W
FRIB
x
-
-
RAS05
N/A
N/A
Flexi RF FRJA Module 2000 Dual 50 W
x
-
-
RAS06
N/A
N/A
Flexi RF Module 2000 Single 50 W
FRJB
x
-
-
RAS06
N/A
N/A
Flexi 3sector RF Module 2100
FRGF
-
x
-
RU10
N/A
N/A
Flexi 3sector RF Module 2100
FRGP
-
x
-
RU20 on top
RL20
N/A
Flexi 3sector RF Module 1.7/2.1
FRIE
-
x
-
RU20 on top
RL10
N/A
Flexi 3sector RF Module 1500
FRKA
-
x
-
RU20
N/A
N/A
Flexi 3sector RF Module 850
FXCA
-
x
-
RU20 on top
RL20
RG10
Flexi 3sector RF Module 850
FXCB
-
-
x
RU30 EP2 RL60
RG30
Flexi 3sector RF Module 840
FXCE
-
-
x
N/A
N/A
DN0971928
RL70
Issue: 01G
Flexi Multiradio 10 Base Station Product Description
Table 5
Issue: 01G
Appendix Flexi BTS hardware releases
Flexi Multiradio BTS RF Module hardware product generations (Cont.)
Module variant
Abbreviat Release 1 Release 2 Release 3 WCDMA ion HW HW HW release
LTE release
GSM release
Flexi 3sector RF Module 900
FXDA
-
x
-
RU20 on top
RL50
RG10
Flexi 3sector RF Module 900
FXDB
-
x
-
RU30 EP2 RL50
RG20 EP2
Flexi 3sector RF Module 900
FXDJ
-
x
-
RU20 on top
N/A
RG10
Flexi 3sector RF Module 1800
FXEA
-
x
-
RU40
RL20
RG10
Flexi 3sector RF Module 1800
FXEB
-
x
-
RU40
RL40
RG20 EP2
Flexi 3sector RF Module 1900
FXFA
-
x
-
RU20 on top
RL40
RG10
Flexi 3sector RF Module 1900
FXFB
-
x
-
RU30 EP2 RL60
RG20 EP1
Flexi 3sector RF Module 1900
FXFC
-
-
x
RU30 EP2 RL60
RG30
Flexi RF Module 900-J triple
FXJB
-
x
-
RU30 EP2 N/A
N/A
Flexi 3sector RF Module 2100
FRGT
-
-
x
RU30 EP2 RL50
N/A
Flexi RF Module 2TX 850
FXCC
-
x
-
N/A
N/A
DN0971928
RL30
43
Appendix Flexi BTS hardware releases
Table 5
44
Flexi Multiradio 10 Base Station Product Description
Flexi Multiradio BTS RF Module hardware product generations (Cont.)
Module variant
Abbreviat Release 1 Release 2 Release 3 WCDMA ion HW HW HW release
LTE release
GSM release
Flexi 3sector RF Module 2600
FRHA
-
x
-
N/A
RL10
N/A
Flexi 3sector RF Module 760
FRBB
-
x
-
N/A
RL30
N/A
Flexi 3sector RF Module 800EU
FRMA
-
x
-
N/A
RL10
N/A
Flexi 3sector RF Module 800
FRMD
-
x
-
N/A
RL40
N/A
Flexi 3sector RF Module 2100
FRGS
-
-
x
RU30 EP2 RL50
N/A
Flexi RF Module 6TX 2600
FRHC
-
-
x
N/A
RL50
N/A
Flexi RF Module 6TX 800
FRMC
-
-
x
N/A
RL50
N/A
Flexi RF Module 6TX 700
FRPA
-
-
x
N/A
RL50
N/A
Flexi RF Module 6TX 700
FRPB
-
-
x
N/A
RL50
N/A
Flexi RF Module 6TX 2600
FRHF
-
-
x
N/A
RL50
N/A
Flexi RF Module 6 x 10 W 2300
FZNC
-
-
x
N/A
RL25
N/A
DN0971928
Issue: 01G
Flexi Multiradio 10 Base Station Product Description
Table 5
Flexi Multiradio BTS RF Module hardware product generations (Cont.)
Module variant
Abbreviat Release 1 Release 2 Release 3 WCDMA ion HW HW HW release
LTE release
GSM release
Flexi RF Module 8 x 10 W 2600
FZHA
-
-
x
N/A
RL25
N/A
Flexi RF Module 6 x 60 W 1800
FXED
-
-
x
N/A
RL70
N/A
Table 6
Issue: 01G
Appendix Flexi BTS hardware releases
Flexi Multiradio BTS Remote Radio Head hardware product generations
Module variant
Abbrevi ation
Release 1 HW
Release 2 HW
Release 3 HW
Release 4 HW
WCDMA LTE release release
GSM release
Flexi RRH 2TX 850
FHCD
-
x
-
-
RU50
N/A
N/A
Flexi RRH 2TX 900
FHDA
-
x
-
-
RU30 EP1
RL70
RG10
Flexi RRH 2TX 900
FHDB
-
x
-
-
RU40
RL40
RG30
Flexi RRH 2100 Single 70W
FRGG
x
-
-
-
RU20 on N/A top
N/A
Flexi RRH 2TX 2100
FRGQ
-
x
-
-
RU20 on RL30 top
N/A
Flexi RRH 2TX 1900
FHFA
-
x
-
-
RU50
N/A
N/A
Flexi RRH 4TX 1.7/2.1
FRIG
-
x
-
-
N/A
RL40
N/A
Flexi RRH 2TX 850
FHCA
-
x
-
-
N/A
RL30
N/A
DN0971928
45
Appendix Flexi BTS hardware releases
Table 6
46
Flexi Multiradio 10 Base Station Product Description
Flexi Multiradio BTS Remote Radio Head hardware product generations (Cont.)
Module variant
Abbrevi ation
Release 1 HW
Release 2 HW
Release 3 HW
Release 4 HW
WCDMA LTE release release
GSM release
Flexi RRH 2TX 2600
FRHB
-
x
-
-
N/A
RL30
N/A
Flexi RRH 2TX 1800
FHEA
-
x
-
-
RU40
RL20
RG10
Flexi RRH 2TX 730
FRLB
-
x
-
-
N/A
RL20
N/A
Flexi RRH 2TX 800EU
FRMB
-
x
-
-
N/A
RL10
N/A
Flexi RRH 2TX 2100
FHGA
-
x
-
-
N/A
RL70
N/A
Flexi RRH 4TX 2100
FHGB
-
x
-
-
N/A
RL70
N/A
Flexi RRH 2TX 1800
FHEF
-
x
-
-
N/A
RL70
N/A
Flexi RRH 2TX 1800
FHEB
-
-
x
-
N/A
RL50
RG30
Flexi RRH 1800
FHEC
-
-
x
-
N/A
RL60
N/A
Flexi RRH 4TX 2600
FRHE
-
-
x
-
N/A
RL50
N/A
Flexi RRH 4TX 2600
FRHD
-
-
x
-
N/A
RL50
N/A
DN0971928
Issue: 01G
Flexi Multiradio 10 Base Station Product Description
Table 6
Issue: 01G
Appendix Flexi BTS hardware releases
Flexi Multiradio BTS Remote Radio Head hardware product generations (Cont.)
Module variant
Abbrevi ation
Release 1 HW
Release 2 HW
Release 3 HW
Release 4 HW
WCDMA LTE release release
GSM release
Flexi RRH 2TX 700
FRPK
-
-
x
-
N/A
RL60
N/A
Flexi RRH 8TX 2600 BD41
FZHJ
-
-
x
-
N/A
RL45
N/A
Flexi RRH 4TX 2300
FZNI
-
-
x
-
N/A
RL25
N/A
Flexi RRH 2TX 2100
FRGY
-
-
-
x
RU50
N/A
N/A
Flexi RRH 4TX 1900
FHFB
-
-
-
x
N/A
RL70
N/A
DN0971928
47
View more...
Comments