Nemoto Dual Shot GX Service Manual 2008.05.27
Short Description
nemoto manual...
Description
044-200133.03
3nd edition
Conrast Delivery System
Dual Shot Service Manual
044-200133.00.03
Nemoto Kyorindo Co., Ltd. 2-27-20 Hongo, Bunkyo-ku, Tokyo 113-0033, Japan 6/4/2007
044-200133.03
Dual Shot
Nemoto Kyorindo Co., Ltd. 6/4/2007
Service Manual. 044-200133.00.03
044-200133.03
Dual Shot
Table of Contents
1. Preface ....................................................... 1 1.1. How 1.1.1. 1.1.2. 1.1.3.
to read this service manual ........................... 1 How to read the revision history ...................... 1 How to read the cover page ............................ 2 How to read the text .................................. 3
1.2. Object Equipment .......................................... 4 1.3. Cautions for Safety Use ................................... 4 1.3.1. Symbols ............................................... 5 1.3.2. Cautions when installing .............................. 6 1.3.3. Cautions when checking ................................ 6 1.3.4. Cautions when repairing ............................... 6 1.4. Manual Construction ....................................... 7
2. Specifications ................................................ 9 2.1. Dimensions ................................................ 9 2.2. Weight .................................................... 9 2.3. Appropriate Syringe ....................................... 10 2.4. Operation Range ........................................... 10 2.5. Safety Device ............................................. 11 2.5.1. Error Message and Halt ................................ 11 2.5.2. Fuse .................................................. 11 2.5.3. Pressure monitor ...................................... 11 2.5.4. Flow rate monitor ..................................... 11 2.5.5. Injection volume monitor .............................. 11 2.5.6. Over injection time ................................... 11 2.5.7. Motor monitor ......................................... 11 2.5.8. Sensor monitor ........................................ 11
3. Stand Assembling .............................................. 13 3.1. Unpacking ................................................. 13 3.2. Assembling Stand .......................................... 13 3.3. Installing Floor Stand Type ............................... 14 3.4. Installing Ceiling Mounting Type .......................... 15
Nemoto Kyorindo Co., Ltd. 081-200133.00.03
6/4/2007
044-200133.03
Table of Contents
Dual Shot
3.5. Connecting Head Arm and Ceiling Mounting Device ........... 16 3.6. Connecting Console ........................................ 17
4. Console lnitialization ........................................ 19 4.1. Call of Service Screen .................................... 19 4.2. Setup Screen .............................................. 20 4.3. Setting Upper Left Position (Touch Panel) ................. 21 4.4. Setting Lower Right Position (Touch Panel) ................ 21 4.5. Check of Setup State (Touch Panel) ....................... 22 4.6. Service Menu Screen ....................................... 22 4.7. Date/time Setup Screen .................................... 23 4.8. Function Setup Screen (1) ................................. 24 4.9. Function Setup Screen (2) ................................. 26 4.10. Function Setup Screen (3) ................................ 28 4.11. Error Log ................................................ 29 4.12. Abort Log ................................................ 32 4.13. Interface monitor screen ................................. 33 4.14. NV-RAM Clear screen ...................................... 33 4.15. Injector Status screen ................................... 33 4.16. Program Change ........................................... 34 4.17.FROM 交換 ................................................. 35 4.18. Initialization of Console ................................ 36 4.19. Selection of head connected .............................. 37 4.20. Operation Check .......................................... 38
5. Daily Check and Periodic Inspection ........................... 39 5.1. Daily Check ............................................... 39 5.1.1. Check of the system and accessories ................... 39 5.1.2. Check of the head and stand ........................... 39
Nemoto Kyorindo Co., Ltd. 6/4/2007
081-200133.00.03
044-200133.03
Dual Shot
Table of Contents
5.1.3. Check of the ceiling mounting arm ..................... 40 5.1.4. Cleaning .............................................. 40 5.2. Inspection (Mandatory items for serviceman) ............... 40
6. Troubleshooting ............................................... 47 6.1. Problems without Error Display ............................ 47 6.1.1. Power can not be turned on ............................ 47 6.1.2.Touch panel can not be used. ........................... 47 6.1.3. Error sound is generated and console does not start up 47 6.1.4. Heater does not get warm. ............................. 47 6.2. Problems with Error Display ............................... 48 6.2.1. ERR1 .................................................. 48 6.2.2. ERR2 .................................................. 48 6.2.3. ERR3 .................................................. 48 6.2.4. ERR4 .................................................. 49 6.2.5. ERR6 .................................................. 49 6.2.6. ERR11 ................................................. 49 6.2.7. ERR12 ................................................. 49 6.2.8. ERR13 ................................................. 50 6.2.9. ERR14 ................................................. 50 6.2.10. ERR15 ................................................ 50 6.2.11. ERR16 ................................................ 50 6.2.12. ERR17 ................................................ 50 6.2.13. ERR18 ................................................ 51 6.2.14. ERR20 ................................................ 51 6.2.15. ERR30 ................................................ 51 6.2.16. ERR50 ................................................ 51 6.2.17. ERR90 ................................................ 51 6.2.18. ERR91 ................................................ 51 6.2.19. ERR92 ................................................ 52 6.2.20. ERR93 ................................................ 52 6.2.21. ERR95 ................................................ 52 6.2.22. ERR96 ................................................ 52
7. Head Calibration .............................................. 53 7.1. Connection for Head Calibration ........................... 53 7.2. Configuration of Communication Software ................... 53
Nemoto Kyorindo Co., Ltd. 081-200133.00.03
6/4/2007
044-200133.03
Table of Contents
Dual Shot
7.3. Programming Procedure ..................................... 54 7.4. Set for Programming Mode .................................. 57 7.5. Pressure Offset Setting ................................... 57 7.6. List of Commands .......................................... 58 7.7. EEPROM Initialization ..................................... 59 7.8. Calibration Data Display .................................. 59 7.9. Front Limit Calibration ................................... 60 7.10. Offset Programming and Check of Electromagnetic Brake .... 61 7.11. Jog Shuttle Programming .................................. 64 7.12. Buzzer Volume Programming ................................ 64 7.13. Pressure Gain Programming ................................ 65 7.14. Calibration Mode in General .............................. 66 7.15. Setting of Low Pressure Warning .......................... 67 7.16. Offset/Pressure Display Adjustment from Console .......... 68
8. Program Update ................................................ 71 8.1. Connection of Program Updating Jig ........................ 71 8.2. Procedure of Program Change ............................... 72 8.3. Program Initialization .................................... 75
9. Rewrite of Altera ............................................. 77 9.1. Connection of Arutera Rewriting Jig ....................... 77 9.2. Rewriting Procedure ....................................... 78 9.3. Selection of Writing Tools ................................ 84
10.
Contact Information ......................................... 85
Nemoto Kyorindo Co., Ltd. 6/4/2007
081-200133.00.03
001-200134.04
Dual Shot
Preface
1
1. Preface 1.1. How to read this service manual The Press Pro serivce manual is used as an example. 1.1.1. How to read the revision history
Updating date and document reference number
Revision number and contents of modifications are described.
Detail of the contents of modification
Document reference number Reference number of the document which constitutes the manual
● ●
Contents of modification
This manual consists of plural chapters, and each chapter has its document reference number. The document reference numbers are listed in the manual construction table.
Service Manual 044-200133.01.03
1
Nemoto Kyorindo Co., Ltd. 6/4/2007
1
001-200134.04
Preface
Dual Shot
1.1.2. How to read the cover page Document reference number Revision number Product name
Image of system
Manufacturer name
Manufacturer address
Printed date of this manual
Document reference number
The reference number of when storing and controling the manual (The document reference number on the cover page is the reference number for this whole manual)
Revision number
Revision number of the manual
Product name
Name of the system described in this manual
Image of system
Image figure (It may differ from an actual product.)
Manufacturer name
The manufacturer of this product
Manufacturer address
The address of the manufacturer
Printed date of this manual
The date of when this manual was printed out from the source code. (It differs from the created date of this manual.)
Nemoto Kyorindo Co., Ltd. 6/4/2007
2
Service Manual 044-200133.01.03
001-200134.04
Dual Shot
Preface
1
1.1.3. How to read the text Document reference number Chapter number
System name
Chapter title
Manual classification Manufacturer Printed date of this man-
Page number
Document reference number
A reference number used when storing and controling this manual (Each chapter has its assigned number.)
Chapter number
Number of the chapter (The number corresponds with the headline on the first line of the page.)
Chapter title
Title of the chapter
Name of the system
Name of the system described in this manual
Name of manufacturer
Manufacture of the system
Manual classification
Kind of manual
Printed date of this manual
The date when this manual was printed from the source code. (It differs from the created date of this manual.)
Page number
The page number counted from the first page of Chapter 1.
Service Manual 044-200133.01.03
3
Nemoto Kyorindo Co., Ltd. 6/4/2007
1
001-200134.04
Preface
Dual Shot
1.2. Object Equipment The software revisions of the equipment described in this manual are listed in the system configuration table.
1.3. Cautions for Safety Use
Symbol
Danger
This symbol indicates that hazards which will result in serious personal injury or death may occur immensely when the system is incorrectly operated.
Warning
This symbol indicates that hazards which could result in serious personal injury or death may occur when the system is incorrectly operated.
Caution
This symbol indicates that hazards which could result in personal injury or equipment or property damage when the system is incorrectly operated.
Nemoto Kyorindo Co., Ltd. 6/4/2007
Description
4
Service Manual 044-200133.01.03
001-200134.04
Dual Shot
Preface
1
1.3.1. Symbols Symbols used on the Dual Shot and in this manual Symbol
Description Beware of getting your fingers pinched. Caution. Read attached description. Avoid direct sunlight. Indicates that wet by rain is prohibited. Indicates cautions for handling. Indicates not to turn over. Indicates the temperature conditions. Indicates the data of manufacture. Indicates that the power in the main unit is ON. Indicates that the power in the main unit is OFF. Indicates that the power in the console is ON/OFF. Indicates a protective earth terminal. Indicates an alternating current (AC). Indicates hazardous voltages. Indicates start of injection. Indicates that injection is paused. Indicates conformity to CF type. Forward Reverse Accelerating Displays a list of memories for each injection mode. Switches over the injection mode screen. Displays a list of results. Indicates conformity to the European Medical Device Standard. Indicates that wastes of electric and electronic equipment must not be disposed of as unsorted municipal wastes and must be collected separately. Please contact an authorized representative of the manufacturer regarding the infomation about decomissioning of your equipment.
Service Manual 044-200133.01.03
5
Nemoto Kyorindo Co., Ltd. 6/4/2007
1
001-200134.04
Preface
Dual Shot
1.3.2. Cautions when installing
Danger １）Take care of handling the package as it is very heavy. ● Ensure to get work authorization from a person in charge before work. ● Ensure to draw up a job finished report after the completion of work. ● Submit a repair report to the manufacturer.
1.3.3. Cautions when checking
Warning １）Take out the power cable from the outlet throughout the checking procedure. ２）Take great care not to receive an electric shock, if the checking work needs to be done with power on. ３）When checking the system operation, ensure to install the housings of the main unit and head before operating. ● Be sure to get work authorization from a person in charge before work. ● After the completion of work, draw up a job finished report and be sure to accept written confirmations.
1.3.4. Cautions when repairing
Warning １）Take out the power cable from the outlet throughout the checking work. ２）Take great care not to receive electric shock, if the checking work needs to be done with power on. ３）Before checking the system operation, ensure to install the housings of the main unit and the head.
Nemoto Kyorindo Co., Ltd. 6/4/2007
6
Service Manual 044-200133.01.03
001-200134.04
Dual Shot
Preface
1
Caution １）Take great care when using organic solvent. (Housing and coating may be damaged.) ● Be sure to get work authorization from a person in charge before work. ● Be sure to draw up a job finished report after the completion of work. ● Submit a repair report to the manufacturer except for slight repair, such as replacement of consumables. 1.4. Manual Construction This manual comprises of the following chapters. Preface Specifications Stand Assembling Console Initialization Daily Check and Periodic Inspection Troubleshooting Head Calibration Program Update Rewrite of Arutera Contact Information
＜ 044-200133.01.03 ＞ ＜ 044-200133.02.03 ＞ ＜ 044-200133.03.03 ＞ ＜ 044-200133.04.03 ＞ ＜ 044-200133.05.03 ＞ ＜ 044-200133.06.03 ＞ ＜ 044-200133.07.03 ＞ ＜ 044-200133.08.03 ＞ ＜ 044-200133.09.03 ＞ ＜ 044-200133.10.03 ＞
As for the head assembling procedure and console assembling procedure, please refer to the respective assembling manuals. As for the part numbers, please refer to the Parts Manual.
Service Manual 044-200133.01.03
7
Nemoto Kyorindo Co., Ltd. 6/4/2007
1
001-200134.04
Preface
Nemoto Kyorindo Co., Ltd. 6/4/2007
Dual Shot
8
Service Manual 044-200133.01.03
044-200133.03
Dual Shot
Specifications
2
2. Specifications 2.1. Dimensions Head Console Main unit Pole stand
520 × 112 × 180mm 107 × 270 × 248mm 240 × 190 × 100mm 600 × 600 × 1200mm
2.2. Weight Head Console Main unit Pole stand
7kg 3.7kg 6kg 11.5kg
Item Electric rating
Console Rated voltage Output or power consumption Protection type
Outline rating Environment
Durable years An application regulation and standard
Service Manual 044-200133.02.03
230V ± 10V 50/60Hz 260VA Class Ⅰ CF type
Protection grade Outline protection IPX1 format Transportation/ At the time of unworking Storage Ambient air -40 ～ 70 ℃ temperature
At the time of operation 10 ～ 40 ℃
R e l a t i v e - h u m i d i t y 10 ～ 100％ 30 ～ 75％ range Normal atmosphere 50 ～ 106ｋPa 70 ～ 106ｋPa range 6 years (including appropriate maintenance and check.) IEC60601-1(1988) IEC60601-1-2(2001)
9
Nemoto Kyorindo Co., Ltd. 6/4/2007
2
044-200133.03
Specifications
Dual Shot
2.3. Appropriate Syringe Product name
Production approval number
Nemoto Kyorindo Co., Nemoto disposable Ltd. syringe
100mL
14300BZZ00013
200mL
14300BZZ00013 15800BZZ00973000 20400BZZ00589000 20200BZZ01134000
2.4. Operation Range Item Injection ume
Syringe
Setting range
vol- 100mL
1 ～ 100mL
1mL/Step
200mL
1 ～ 200mL
1mL/Step
50mL（B head）
1 ～ 60mL
1mL/Step
100/200mL
0.1 ～ 10.0mL/sec
（0.1mL/sec）/Step
50mL（B head）
0.1 ～ 10.0mL/sec
（0.1mL/sec）/Step
100mL
10 ～ 300psi 1 ～ 21kg/cm2 100 ～ 2058kPa
10psi/Step 0.1kg/cm2 /Step 100kPa/Step
200mL
10 ～ 215psi 1 ～ 15kg/cm2 100 ～ 1470kPa
10psi/Step 0.1kg/cm2 /Step 100kPa/Step
50mL（B head）
10 ～ 215psi 1 ～ 15kg/cm2 100 ～ 1470kPa
10psi/Step 0.1kg/cm2 /Step 100kPa/Step
Scan time
50/100/200mL
0 ～ 300sec
1sec/step
Interval time
50/100/200mL
0 ～ 300sec
Delay time
50/100/200mL
0 ～ 300sec
flow rate
Pressure limit
Nemoto Kyorindo Co., Ltd. 6/4/2007
10
Service Manual 044-200133.02.03
044-200133.03
Dual Shot
Specifications
2
2.5. Safety Device 2.5.1. Error Message and Halt ERR1 - 90 Buzzer 2.5.2. Fuse Main unit
Halt after an error message is displayed Halt after a buzzer goes off
5A250V(AC power) F1・F2 0.5A HM05 for head heater F3・F4 3.2A HM32 for head motor
2.5.3. Pressure monitor Monitoring injection pressure When the abnormal pressure occurs, it functions towards the safe direction. 2.5.4. Flow rate monitor Monitoring flow rate. Injection stops when the flow rate is +25% of the set up value. (over flow rate) 2.5.5. Injection volume monitor Monitoring injection flow rate. When the injection was performed more than the set up volume, it functions towards the safe direction. Error occurs when the injection volume is +2mL of the set up value.（over injection volume） 2.5.6. Over injection time Injection stops and an error occurs when the set up time is +25%. 2.5.7. Motor monitor When the motor operates abnormally, it functions towards the safe direction. 2.5.8. Sensor monitor When any sensor breaks down, it monitors so that dangerous operation may not occur.
Service Manual 044-200133.02.03
11
Nemoto Kyorindo Co., Ltd. 6/4/2007
2
044-200133.03
Specifications
Nemoto Kyorindo Co., Ltd. 6/4/2007
Dual Shot
12
Service Manual 044-200133.02.03
044-200133.03
Dual Shot
Stand Assembling
3
3. Stand Assembling 3.1. Unpacking ● The system is delivered in one package. １）Take great care in handling the package since it is heavy. ２）An operation manual is packed together. ３）Syringes are packed in the small package. 3.2. Assembling Stand
1) Attach the stand pole to the bottom of the stand base ① with a supplied bolt. Use a supplied hexagon wrench for attaching. 2) Attach the connecting parts of the head arm ④ to the stand pole. 3) Attach the stopper ⑤ (3 pieces of socket set screws M6 × 6mm) . 4) Insert the rotation limit screw ⑦ . 5) Connect the head cable to the head extension cable. 6) Fix the cable holder ③ with two screws (M4 × 8mm) ⑥ .
Service Manual 044-200133.03.03
13
Nemoto Kyorindo Co., Ltd. 6/4/2007
3
044-200133.03
Stand Assembling
Dual Shot
3.3. Installing Floor Stand Type
1) Lead the head extension cable ① from the planned console location to the location where the head possibly moves with the length of the head cable around the CT scanner. 2) Install the head and head stand ② in the shooting room. 3) Install the console ③ and main unit ⑧ . 4) Check the power supply voltage of the outlet (which shall be wihin ± 10% of the rated voltage) and connect the power cable ④ . 5) Place the ground wire so that the earth potential level of the head becomes the same with that of the bed of the CT equipment. (Discussion with a manufacturer of CT equipment is necessary.) 6) Connect the hand switch ⑤ . 7) Turn ON the power on the rear side of the console. In the case of interlocking use, installation is possible when the power is ON. 8) In the case of interlocking use, attach the optical conversion connectors ⑦ to both ends of the two optical cables ⑥ when connecting the CT equipment. 9) Attach the coversion cables ⑨ between the console and the optical conversion connectors.
Nemoto Kyorindo Co., Ltd. 6/4/2007
14
Service Manual 044-200133.03.03
044-200133.03
Dual Shot
Stand Assembling
3
3.4. Installing Ceiling Mounting Type
1) Lead the head extension cable ① from the planned console location to the location where the head is permanently installed. 2) Connect the head cable ② and the head extension cable inside the cover of the ceiling mounting device and lead the head extension cable ① to the console ③ . 3) Install the console ③ and the main unit ⑧ . 4) Check the power supply voltage of the outlet (which shall be wihin ± 10% of the rated voltage) and connect the power cable ④ . 5) Place the ground wire so that the earth potential level of the head becomes the same with that of the bed of the CT equipment. (Discussion with a manufacturer of the CT equipment is necessary.) 6) Connect the hand switch ⑤ . 7) Connect the conversion cables ⑨ . 8) Connect the head extension cable ① with the main unit ⑧ . 9) In the case of interlocking use, attach the optical conversion connectors ⑦ to both ends of the two optical cables ⑥ when connecting the CT equipment. 10)Turn on the power switch on the rear side of the console.
Service Manual 044-200133.03.03
15
Nemoto Kyorindo Co., Ltd. 6/4/2007
3
044-200133.03
Stand Assembling
Dual Shot
3.5. Connecting Head Arm and Ceiling Mounting Device
②
①
Attach the connecting arm ① between the ceiling mounting device ② . To switch from the floor standing type to the ceiling mounting type, replace the head arm also for easy on-site installation .
Nemoto Kyorindo Co., Ltd. 6/4/2007
16
Service Manual 044-200133.03.03
044-200133.03
Dual Shot
Stand Assembling
3
3.6. Connecting Console
① Power cable ② Hand switch cable ③ Console cable ④ Head cable and head extension cable Ensure to lock the connector if it has a locking system.
Service Manual 044-200133.03.03
17
Nemoto Kyorindo Co., Ltd. 6/4/2007
3
044-200133.03
Stand Assembling
Nemoto Kyorindo Co., Ltd. 6/4/2007
Dual Shot
18
Service Manual 044-200133.03.03
044-200133.03
Dual Shot
Console lnitialization
4
4. Console lnitialization 4.1. Call of Service Screen
①
1) Open the cover on the rear side of the console and turn the switch on S-3 on with a thin stick and then supply the power. Note: Error sound normally goes off from the head during initialization, but there is no need to worry abou it. (Reason: The head recognizes initialization as an error because no communication takes place between the head and the console.)
Service Manual 044-200133.04.03
19
Nemoto Kyorindo Co., Ltd. 6/4/2007
4
044-200133.03
Console lnitialization
Dual Shot
4.2. Setup Screen
1) Press “CH” of the panel keys when the calibration of the touch panel is completed. 2) To perform calibration, press the recess button ① with a thin stick. Note: The touch panel does not respond unless calibration is done.
Nemoto Kyorindo Co., Ltd. 6/4/2007
20
Service Manual 044-200133.04.03
044-200133.03
Dual Shot
Console lnitialization
4
4.3. Setting Upper Left Position (Touch Panel) Touch the point ① shown in the upper left of the screen with an end-rounded stick to check that the coordinate positions are indicated. After checking, press “CH” of the panel keys to register the positions.
①
4.4. Setting Lower Right Position (Touch Panel) Touch the poin ② shown in the lower right of the screen with an end-rounded stick to check that the coordinate positions are indicated. After checking, press “CH” of the panel keys to register the positions.
②
Service Manual 044-200133.04.03
21
Nemoto Kyorindo Co., Ltd. 6/4/2007
4
044-200133.03
Console lnitialization
Dual Shot
4.5. Check of Setup State (Touch Panel)
③
Touch the center point ③ with an end-rounded stick to check that the coordinate values are indicated and they are within the permissible range shown below. X coordinate ＝ 395 - 405 Y coordinate ＝ 295 - 305 When the values are not within the ranges above, press the recess button of the panel keys for resetting. When the values are within the ranges, press “CH” of the panel keys and then the setting will be completed.
4.6. Service Menu Screen
1) 2) 3) 4) 5) 6) 7)
Date/Time Set Function Set Error Log Abort Log Interface Monitor NV-RAM Clear Injector Status
After setting is completed, press “End.”
Nemoto Kyorindo Co., Ltd. 6/4/2007
22
Service Manual 044-200133.04.03
044-200133.03
Dual Shot
Console lnitialization
4
After the “End is pressed, the presser will be automatically shut down. Do not turn off the power on the rear side of the console before automatic shutdown.
4.7. Date/time Setup Screen
Press the key + or － under the item you want to change. Press “Return” and the setting will be completed.
Service Manual 044-200133.04.03
23
Nemoto Kyorindo Co., Ltd. 6/4/2007
4
044-200133.03
Console lnitialization
Dual Shot
4.8. Function Setup Screen (1)
1) Start Delay Time lag between when the injection start button is pressed and when an injection actually starts will be set when “ON” is selected. (Factory Shipment: OFF fixed) 2) Ramp Up Time The time of when the actual flow rate reaches the designated flow rate will be set when “ON” is selected. (Factory Shipment: OFF fixed) 3) Pressure Unit It allows to select the pressure setting and display unit. The setting units are: kg/cm2 PSI kPa （Factory Shipment:PSI） 4) A 200mL Upper Pressusre Limit (Factory Shipment:215 PSI) It allows to select the upper pressure limit of when the 200mL syringe is used.
Setting values 2 value selection
Nemoto Kyorindo Co., Ltd. 6/4/2007
kg/cm2
PSI
kPa
１５
２１５
１４７０
２１
３００
２０５８
24
Service Manual 044-200133.04.03
044-200133.03
Dual Shot
Console lnitialization
4
5) B 50mL Upper Pressure Limit (Factory Shipment: 215PSI) Invalid 6) External Interface (Factory Shipment: Type Z) TypeZ without interlocking TypeA Toshiba interlocking Not determined except for above 7) Flow Rate Minimum Unit (Factory Shipment: 0.1) It allows to select the minimum unit for an injection.
Setting value
Description
０．１ The rate is increased/decreased in increments of 0.1mL/sec every time the arrows on both sides of the input bar is pressed.
０． ０１
The rate setting is under 2.0mL/sec: The rate is increased/decreased in increments of 0.01mL/sec every time the arrows on both sides of the input bar are pressed. The rate setting is 2.0mL/sec or more: The rate is increased/decreased in increments of 0.1mL/sec every time the arrows on both sides of the input bar are pressed.
In some cases, the flow rate display does not change even when the flow rate is changed for 0.01mL/sec. Note that the planned injection time will change instead.
Service Manual 044-200133.04.03
25
Nemoto Kyorindo Co., Ltd. 6/4/2007
4
044-200133.03
Console lnitialization
Dual Shot
4.9. Function Setup Screen (2)
1) Inj. Mode Selection (Factory Shipment: SEL2) It allows to select a setup mode out of SEL 2 to SEL 5. The injection mode slection screen changes in accordance to the setting. SEL
Mode
Summary
２
A1 → B1
A1 is injected and then B1 is injected.
３
A2 → B1
A is injected in 2 phases and then B1 is injected.
４
A1 ＋ B1
A1 and B1 are indected simultaneously.
５
AB1 → AB2
A1 is injected and then B1 is injected. A2 is injected and then B2 is injected.
６
A→A＋B
A1 is injected and then A2 and B1 is injected simultaneously.
2) Data Transmission (Factory Shipment: OFF fixed) ON: Injection data is output to serial communication. 3) Scan Timer (Factory Shipment: ON+Sound fixed) ON: It allows to select whether the scan timer is displayed or not on the screen. ON + sound: It allows to go off the beep sound 5 seconds before the set up time and just on the set up time.
Nemoto Kyorindo Co., Ltd. 6/4/2007
26
Service Manual 044-200133.04.03
044-200133.03
Dual Shot
Console lnitialization
4
4) Contrast Medium Selection Retained (Factory Shipment: ON fixed) ON: It allows to memorize the type of the contrast medium in the HAT and IHAT protocols. 5) External Input Control (specially ordered function) (Factory Shipment: OFF fixed) ON: Nurse call : When an additional button is pressed, the “Nurse Call” will be displayed on the screen. Injector controll: When an additional button is pressed during an A injection, the injetion shifts to a B injection. 6) Contrast Timer (Factory Shipment: OFF fixed) ON: It allows to automatically adjust the screen contrast. When any of the head keys or the console screen is not operated more than 30 seconds, the screen color gets darker. When any of the head keys or the console screen is operated, the screen returns to the normal brightness. 7) Change of Detailed Area Name (Factory Shipment: ON fixed) ON: The detailed area names stored in the CF card are displayed. OFF: Standard detailed area names are displayed.
Service Manual 044-200133.04.03
27
Nemoto Kyorindo Co., Ltd. 6/4/2007
4
044-200133.03
Console lnitialization
Dual Shot
4.10. Function Setup Screen (3)
1) Head Display Function (Factory Shipment: OFF fixed) ON: Head Display Function Will be available. 2) Total Time Adjustment for Weight Input (Factory Shipment: ON fixed) ON: Function of total time adjustment on the weight input screen is valid. The flow rate is changed when the total time is changed. 3) Input of Sub Detailed Area Item (Factory Shipment: not determined ON: It allows to enter a name of the sub detailed area item with the key board. OFF: It allows to select a name of the sub detailed area item from the list. 4) Injection Screen Remaining Volume (Factory Shipment : not determined) ON: It allows to display the remainig volume on the injecting screen. (The injection volume is not displayed.) OFF: It allows to display injection volume on the injecting screen. (The remaining volume is not displayed.) 5) Auto/Manual Selection (Factory Shipment: not determined) It allows to set mixture ratio in the mode of A and B simultaneous injection. 6) Stop Key Function (Factory Shipment: Hold) When the touch panel is touched during an injection, it allows to stop an injeciton in the same way as the stop key on the head is pressed.
Nemoto Kyorindo Co., Ltd. 6/4/2007
28
Service Manual 044-200133.04.03
044-200133.03
Dual Shot
Console lnitialization
4
4.11. Error Log
Error log The latest 10 errors are displayed. When “Next” is touched, the remaining five errors will be displayed. Press “Return” when to go back to the menu screen. Status A “ List of Error Etatus” is shown on the next page.
Service Manual 044-200133.04.03
29
Nemoto Kyorindo Co., Ltd. 6/4/2007
4
044-200133.03
Console lnitialization
Dual Shot
List of Error Status Error description
Status
Remarks
Press Over
1
Pressure over is detected more than 330PSI.
Volume Over
2
Error more than 1mL occurred.
Speed Over
3
Error over ± 25% occurred.
Time Over
4
Injection time exceeded 125%.
Position Error
5
not determined
Motor Error
6
The motor did not operate more than 1 second.
Hardware Error
7
Detected hard error
Encoder Error
11
Encoder output was not detected.
Power Down Error
12
Power was turned on again too quickly or fuse on the drive board is blown.
Limit Error
13
Front and rear limits were detected simultaneously.
Safety Board Error
14
The motor operated unexpectedly.
Syringe Error
15
Syringe type changed during injection.
System Communication Error
16
Communication error between the head and the console.
Switch Error
17
Power was turned on with the switch pressed.
Slit Pulse Error
18
Slit pulse is undetectable.
Protocol Error
20
Communication error between the head and the console.
Connect Device Error
30
Connection error between the head and the console.
Power Supply Error
50
The head is not connected.
Over Run
91
Communication error
Framing Error
92
Communication error
Parity Error
93
Communication error
Break Error
94
Communication error
BCC Error
95
Communication error
Retry Error
96
Communication error
C command time out
97
Interlocking communication error
Over Run &Framing Error & 98 Parity Error
Interlocking communication error
Over Run & Parity Error
99
Interlocking communication error
Framing Error & Parity Error
100
Interlocking communication error
Over Run & Framing Error & 101 Parity Error
Interlocking communication error
Nemoto Kyorindo Co., Ltd. 6/4/2007
30
Service Manual 044-200133.04.03
044-200133.03
Dual Shot
Console lnitialization
4
Warning Description
Number
Remarks
Over pressure limiter
１
This error number is generated when the pressure limit activated and a certain period of time elapsed. (* 1
Detection of low pressure injection
５
This error is generated when 10 mL was continuously injected under the conditions that the flow rate is more than 1.5 mL/sec and the pressure is below 0.3kg/cm2. (Only for A head)
Syringe warning
８
Syringe adapter is unstable. (Only for overseas use)
(*1
Error Conditions Setup flow rate (mL/sec)
Error flow rate (mL/sec)
Error detected time (sec)
0.1 ～ 0.9
0.05
2.0
1.0 ～ 1.9
0.1
2.0
2.0 ～ 2.9
0.2
2.0
3.0 ～ 3.9
0.3
1.5
4.0 ～ 4.9
0.4
1.0
5.0 ～ 5.9
0.5
1.0
6.0 ～ 6.9
0.6
1.0
7.0 ～ 6.9
0.7
1.0
8.0 ～ 8.9
0.8
1.0
9.0 ～ 9.9
0.9
1.0
10.0 ～
1.0
1.0
Service Manual 044-200133.04.03
31
Nemoto Kyorindo Co., Ltd. 6/4/2007
4
044-200133.03
Console lnitialization
Dual Shot
4.12. Abort Log
List of Abort Log Description
Remarks
Receipt of C1 command
CT detected error.
Abort input
Abort was sent from CT.
Abort output
Abort was sent to CT.
Stop order
Stop button was pressed.
Nemoto Kyorindo Co., Ltd. 6/4/2007
32
Service Manual 044-200133.04.03
044-200133.03
Dual Shot
Console lnitialization
4
4.13. Interface monitor screen It allows to monitor interlocking communication status. Please refer to the Interlocking Manual for details.
4.14. NV-RAM Clear screen It allows to initialize NV-RAM. After initialization, all the conditions set in the console are deleted. When this command is executed and then the power is turned on again, error sound goes off and the system does not activate. The situation can be restored after initializing the console. (See the next page.)
4.15. Injector Status screen Injections are counted and the count number is displayed. When the “Clear” is touched, the injection count number will be cleared.
Service Manual 044-200133.04.03
33
Nemoto Kyorindo Co., Ltd. 6/4/2007
4
044-200133.03
Console lnitialization
Dual Shot
4.16. Program Change Replace the F-ROM with a new one to perform program change. Open the cover on the rear side of the console. The F-ROM board fixed with two screws will appear. Power off the console before performing replacement of F-ROM.
FROM
After replacement, initialize the console.
Nemoto Kyorindo Co., Ltd. 6/4/2007
34
Service Manual 044-200133.04.03
044-200133.03
Dual Shot
Console lnitialization
4
4.17.FROM 交換
B262
B382
S2-2
S2-2
１）In case of installing FROM “B382”, put S2-2 switch ON. ２）In case of installing FROM “B262”, put S2-2 switch OFF. If the dip switch setting is wrong, the console will not start. After exchanged FROM, initialization of the console must be necessary. (Refer to “Initialization of Console”.) In case of exchanging “B382”, FPGA Rev.must be after CIF-04.01.00. In case FPGA Rev. is before CIF-04.01.00, rewrite of FPGA must be necessary. After rewrote FPGA, exchange FROM.
Service Manual 044-200133.04.03
35
Nemoto Kyorindo Co., Ltd. 6/4/2007
4
044-200133.03
Console lnitialization
Dual Shot
4.18. Initialization of Console
To initialize the console, turn off the power of the console, open the lid of the console, turn up the DIP switch S1-4 in the on position and then turn on the console. When the power is supplied, the buzzer sounds. Turn the DIP switch S1-4 in the off position and turn on the console again. It is necessary to perform this procedure after NV-RAM clear or ROM change.
Nemoto Kyorindo Co., Ltd. 6/4/2007
36
Service Manual 044-200133.04.03
044-200133.03
Dual Shot
Console lnitialization
4
4.19. Selection of head connected
In order to set the type of the head to be used, use the 1 of the S1 dip switch. ON: for Dual Shot (AT-D) When this setting is not correct, ERR 30 will be generated. After the head type was changed from the A300 to the Dual Shot (AT-D), select the “Inj. Mode Selection” out of 2 to 6.
Service Manual 044-200133.04.03
37
Nemoto Kyorindo Co., Ltd. 6/4/2007
4
044-200133.03
Console lnitialization
Dual Shot
4.20. Operation Check Syringe presser movement Press the forward, reverse and accelerator keys in order to ensure that the syringe presser operates properly. In particular, ensure that error does not occur when the syringe presser is moved to the front and rear limits. Low flow rate: 1.5mL/sec High flow rate: 8.0mL/sec Ensure that the syringe presser moves in the distance of 10mL and automatically stops when the forward and reverse keys are pressed. Also ensure that the accelerator key allows continuous movement. Setting Ensure that it is possible to set flow rate and injection volume, etc. properly. Injection Ensure that injection can be carried out properly in the set up protocol.
Nemoto Kyorindo Co., Ltd. 6/4/2007
38
Service Manual 044-200133.04.03
044-200133.03
Dual Shot
Daily Check and Periodic In-
5
5. Daily Check and Periodic Inspection Appropriate repair and maintenance need to be performed to maintain the function of the Dual Shot. The following maintenance schedule is recommended. Daily: Check each part of the system and clean the system. Monthly: Check and clean each part of the system and check its operation. Yearly: Calibration and check of each part of the system by our trained service staff are needed in order to maintain the system function. 5.1. Daily Check Ensure to perform the following checks before using this system. If any malfunction is found, immediately stop using the system and contact our trained service staff. 5.1.1. Check of the system and accessories 1) Check movement of the syringe presser of the head by moving it back and forth at high speed to each limit position without mounting the syringe before use. 2) Make sure that all displays and lamps are illuminated. 3) Make sure that no flaws, breaks, and wear are found on the connecting cable of the system. Make sure that the cable is connected properly. Also make that no other equipment except for this system is connected. 4) Make sure that the system and the accessories are not damaged. 5) Use of inappropriate accessories may cause malfunction of the system or damage to the patient. Make sure that they are appropriate.
5.1.2. Check of the head and stand 1) Make sure that no damage such as cracks is found on the head housigs. 2) Make sure that the head does not rotate more than 180 degrees in the vertical and horizontal directions. 3) Make sure that the casters of the stand move smoothly and the locking mechanism operates properly. 4) Make sure that no damage such as cracks is found on the stand and all bolts and screws are tightly screwed.
Service Manual 044-200133.05.03
39
Nemoto Kyorindo Co., Ltd. 6/4/2007
5
044-200133.03
Daily Check and Periodic Inspection
Dual Shot
5.1.3. Check of the ceiling mounting arm (option) 1) Make sure that there are no cracks, bent, wear and looseness on the support and arm. 2) Make sure that the support can be moved up and down lightly without bending. 3) When any defects are detected, stop the operation and inform our trained service staff immediately. 5.1.4. Cleaning 1) One of the main causes of malfunction is adhesion of contrast medium to the head. Always clean the head after use. In general, the contrast medium can be removed easily with a dry cloth immediately after it adheres to it. If the contrast medium dried out, remove it with a cloth moistened with warm water or water. (Never use organic solvent.) 2) If the contrast medium gets inside the system, inform our trained service staff.
5.2. Inspection (Mandatory items for serviceman) Items to be inspected at regular intervals are described in this section. Refer to the Troubleshooting chapter of this manual for dealing with troubles. Syringe attachement section A) Syringe clamper (A) Nemoto 200mL syringe should be easily inserted. A 100mL adapter should be easily inserted. No unnecessary play should exist. No damage of the clamper should be visually checked. ＜ Replace the part if there is damage. ＞ ＜ Clean the part if the movement is not smooth. ＞ B) Syringe adapter (A) Nemoto 50mL syringe should be easily attached/deattached. No unnecessay play should exist. No crack nor damage should be found on the adapter by visual check. ＜ Replace the adapter if cracks or damage are found. ＞ C) Syringe clamper (B) Nemoto 100mL syringe should be easily attached/deattached. A 50mL adapter should be easily inserted. No unnecessary play should exist. No damage of the clamper should be visually checked.
Nemoto Kyorindo Co., Ltd. 6/4/2007
40
Service Manual 044-200133.05.03
044-200133.03
Dual Shot
Daily Check and Periodic In-
5
＜ Replace the part if there is damage. ＞ ＜ Clean the part if the movement is not smooth. ＞ D) Syringe adapter (B) Nemoto 50mL syringe should be easily attached/deattached. No unnecessay play should exist. No crack nor damage should be found on the adapter by visual check. ＜ Replace the adapter if cracks or damage is found. ＞ Head operation section A) Forward/backward (A・B) No damage should be found on the button by visual check. Normal movement is verified when operated. ＜ Replace the sheet switch when damage is found ＞ ＜ If the movement is not normal, investigate the cause and repair the switch ＞ B) Accelerator button (A・B) The accelerator button should function properly. ＜ If the button does not function properly, investigate the cause and repair it. ＞ C) Injection indicating lamp The lamp should be turned on during forward/reverse movement and during an injection. ＜ Replace if the lamp is damaged. ＞ Operation side of the console A) Various settings（A・B） The flow rate, volume and pressure limit are programmed. B) Display (A・B) Ensure that the display changes according to the settings above and the accurate set values are displayed. Rear side of the console A) Cable connector No deformation and damage of the cable connector and no fault of the cable clamp are found.
Service Manual 044-200133.05.03
41
Nemoto Kyorindo Co., Ltd. 6/4/2007
5
044-200133.03
Daily Check and Periodic Inspection
Dual Shot
Head connecting cord A) Head cable No deformation and damage and found. B) Connector No deformation and damage of the connector and no fault of the cable clamp are found. Safety Insulation test device（500V） A) Power supply and main unit The test is performed without the power supplied. Measure the insulating resistance between the electrodes which the earth and two electrodes are short-circuited. The power switch is turned on at this time. B) Power supply and main unit Measure the enclosure leakage current between the power supply and the surface of the case (the insulated metal surface) using the leakage current system. ＜ 0.5mA and below ＞ Stand A) Lock Locking and unlocking should be done without any problems. B) Stand pole No deformation and damage should be confirmed by visual check. C) Casters They should be move smoothly. Head arm A) Horizontal rotation The arm rotation should be limited less than one round. ＜ Replace the lock of the stand. ＞ B) Inclination The arm should not incline with only the weight of the syringe containing the contrast agent. The arm should be inclined by the force with pressure of 2 ± 0.2Kg at the place of the syringe adapter. ＜ Recalibrate the inclination. ＞
Nemoto Kyorindo Co., Ltd. 6/4/2007
42
Service Manual 044-200133.05.03
044-200133.03
Dual Shot
Daily Check and Periodic In-
5
Inside of head A) Motor encoder (A・B) No abnormal noise should occur during rotation. B) Gear, belt, pulley (A・B) Gear ＜ No damage and deformation should be found. ＞ Belt ＜ The margin of 2mm should be exist when the midpoint between the pulleys are pressed. ＞ Pulley ＜ Fixing screws should not be loosened. No scraches and damage are found by visual check. ＞ C) Ball screw(A・B) Noise and decentering should not occur during rotation. ＜ Mounting adjustment or replacement at the factory is needed. ＞ D) Volume pulse sensor (A・B) No damage should be found by visual check. The volume of injection should be checked. ＜ Replace it if damage is found. ＞ E) Front/Rear limit sensor (A・B) Check that the presser stops at the limit position. ＜ Replace the sensor if damaged. ＞ F) Brake (A・B) No noise should occur during rotation. Braking function should operate. ＜ Replace the motor if it is broken. ＞ G) Print-circuit board Visually check that the contrast agent is not attached on the board. ＜ Replace the board if the agent is attached. ＞ H) Internal wiring of the head Visually check the coating damage. ＜ Investigate the cause of the damage and remove the cause. if the damage is severe, replace the cable. Repair it if can be repaired. ＞
Service Manual 044-200133.05.03
43
Nemoto Kyorindo Co., Ltd. 6/4/2007
5
044-200133.03
Daily Check and Periodic Inspection
Dual Shot
Performance/Appearance A) Head cover Visually check the damage and deformation. ＜Replace the cover if the damage/deformation may become trouble for injection.＞ B) Control panel cover Visually check the damage and deformation. ＜ Replace the case if the damage/deformation may lead to the problems for operation or damage the circuit. ＞ C) Description on the labe Description on the label should be legible. ＜ Replace it if it is illegible. ＞ Performance Manometer:25kg/cm2 bull boss type manometer Liquid volume meter: 200mL graduated cylinder Needle: Nemoto 21G-1000 wing needle Inspection liquid: water A) Injection time clock Perform an injection under the conditions that there is no pressure liit and that the injection duration is set to be 60 seconds. Measure the injection duration with a stopwatch. It is acceptable if the injection duration is within 60 ± 1 seconds. B) Injection volume Flow rate: 3mL/sec Volume: 1.5mL・10mL・20mL・40mL・60mL・90mL Head
Volume
Error
A・B
1.5mL
± 0.5mL
A・B
10mL
± 1.0mL
A・B
20mL
A・B A A
40mL
Nemoto Kyorindo Co., Ltd. 6/4/2007
60mL 90mL
44
Service Manual 044-200133.05.03
044-200133.03
Dual Shot
Ｃ） Flow
Daily Check and Periodic In-
5
rate
Flow rate
Volume
Time
Allowable error
0.1mL/sec
10mL
100sec
± 1sec
2.0mL/sec
20mL
10sec
± 1sec
10mL/sec
50mL
5sec
± 0.5sec
Tolerance level in the case of the start-up time being set as 0 second Since the start-up time is set as 2 seconds at the shipment, it becomes +1 second. In the case of shipment setting: 2.0mL/sec 20mL tolerence level 11 ± 1 sec D) Pressure limit ＜ A Head ＞ Pressure limit
: 300PSI, 21 ㎏ /cm2, 2069Kpa
Syringe Needel Flow rate Volume
: Nemoto 100mL disposable syringe : Nemoto 21G-1000 wing needle : 10mL/sec : 100mL
Allowable pressure range：: 21.0 ± 1.5 ㎏ /cm2 ＜ B Head ＞ Pressure limit
: 200PSI, 14 ㎏ /cm2, 1372Kpa
Syringe Needle Flow rate Volume
: Nemoto 100mL disposable syringe : Nemoto 21G-1000 winged needle : 10mL/sec : 50mL
Allowable pressure range：: 21.0 ± 1.5 ㎏ /cm2
Service Manual 044-200133.05.03
45
Nemoto Kyorindo Co., Ltd. 6/4/2007
5
044-200133.03
Daily Check and Periodic Inspection
Nemoto Kyorindo Co., Ltd. 6/4/2007
46
Dual Shot
Service Manual 044-200133.05.03
044-200133.03
Dual Shot
Troubleshooting
6
6. Troubleshooting 6.1. Problems without Error Display 6.1.1. Power can not be turned on Error） Operational error, installation error Cause） The power switch of the main unit is not turned on. Measure）Turn on the power switch of the main unit. Error） Fuse is blown. Cause） Malfunction of the main unit (short-circuit of the power supply line, etc.) Measure Remove the cause for the fuse blown and replace the fuse. Error） Malfunction of transformer Cause） When the power voltage is too high, the temperature fuse inside the transformer gets blown. Measure）Ensure that the power voltage is within the rating and replace the power transformer unit. 6.1.2.Touch panel can not be used. Error） Programming fault of the touch panel Cause) replacement of the program ROM. Measure）Perform calibration of the touch panel on the service screen. Error） A laminate cable is bent. Cause） Error during assembling. Measure）Replace the LCD touch panel. 6.1.3. Error sound is generated and console does not start up Error） Initialization of the console is necessary. Cause） Clearing of NV-RAM or replacement of the program ROM. Measure）Intialize the console when the power is turned on. 6.1.4. Heater does not get warm. No voltage is applied to the heater.） Error） Fuse of the heater is blown. Cause） Short-circuit
Service Manual 044-200133.06.03
47
Nemoto Kyorindo Co., Ltd. 6/4/2007
6
044-200133.03
Troubleshooting
Dual Shot
Measure）Check the circuit of heater and repair the short-circuit before replacing the fuse. (The fuse is mounted on the safety board of the main unit.) The fuse used is different according to the product number. DCD00001 ～MH05 Voltage is applied to the heater.） Error） Heater malfunction Cause） Aged deterioration, start-up problem Measure）Replace the heater. 6.2. Problems with Error Display 6.2.1. ERR1 Error） The pressure value exceeded 330 PSI. Cause） Closed cock of the injection route. Measure）Turn the power on and off. Draw back the presser a little and open the stop cock, and then, proceed normal operation. Cause） Loose contact of the pressure signal or trouble of the sensor cable Measure）Check the pressure signal or replace the pressure sensor cable. 6.2.2. ERR2 Error） The contrast medium was injected 2mL more than the programmed volume. Cause） Encoder trouble Measure）Replace the motor unit. Cause） Trouble of the head CPU board Measure）Replace and recalibrate the head CPU board. 6.2.3. ERR3 Error） The flow rate was +25% or 0.5mL/sec faster than the programmed rate. Condition） set value ＞ 0.25mL/sec when detecting abnormal speed for continuous 0.5sec or longer. set value ＜＝ 0.25mL/sec when detecting the speed of 0.3mL/sec or higher for 0.5 sec..
Nemoto Kyorindo Co., Ltd. 6/4/2007
48
Service Manual 044-200133.06.03
044-200133.03
Dual Shot
Troubleshooting
6
Cause） Trouble of the main unit CPU board・trouble of the drive board Measure）Replace and recalibrate the main unit CPU board or replace the drive board. 6.2.4. ERR4 Error） The injection time was more than 125% of the planned time or over 3 seconds slower than the planned tme. Cause） Trouble of the main unit CPU board or trouble of the drive board Measure）Replace and recalibrate the main unit CPU board・replace the drive board. 6.2.5. ERR6 Error） The presser did not operate over 1 second even attempted to operate. Cause） Motor trouble Measure）Replace the motor. Cause） Running out of the fuse in the drive board Measure）Replace the fuse. Cause） Closed cock of the injection route Measure）Open the cock. (Usually stops due to ERR1). Cause） Malfunction of mechanical section Measure）Replace the mechanical section.( Err 6 has never occurred because of defect.) 6.2.6. ERR11 Cause） Loose contact of connectors/break of the cable/encoder error Measure）Check the connection of the connectors/replace the cable/replace the motor. 6.2.7. ERR12 Cause） Head power supply error (The power was turned on again too quickly.) Measures）Turn the power on again. Cause） Head power supply error (Fuse of the drive board is blown.) Measure）Replace the fuse.
Service Manual 044-200133.06.03
49
Nemoto Kyorindo Co., Ltd. 6/4/2007
6
044-200133.03
Troubleshooting
Dual Shot
6.2.8. ERR13 Error） Front/Rear limit was detected simultaneously. Cause） Trouble of the limit sensor・loose contact of the connector Measure）If the error occurred at the front limit, check the connector related to the rear limit, or replace the rear limit. If the error occurred at the rear limit, check the connector related to the front limit, or replace the front limit. 6.2.9. ERR14 Error） The head CPU does not return watchdog. Cause） Stopped head CPU Measure）Turn off the machine and restart it. If failed to recover, replace the head board. 6.2.10. ERR15 Error） The syringe type changed during injection. Cause） Trouble of the syringe adapter Measure）Check the hook of the syringe. If damaged, replace the syringe adapter. 6.2.11. ERR16 Error） The communication between the head and the console failed. Cause） Malfunction of the communication system, or break or loose connection of the head cable Measure）Check the communication pathway and head cable. 6.2.12. ERR17 Error） Trouble of the operation switch The problem is solved after the hand switch is removed.) ・When the hand switch is removed, the system operates normal. ■ Trouble of hand switch Cause) The start switch or stop switch is kept pressed. (When the RESET switch is kept pressed, an error will not occur.) Measure) Release the button or replace the hand switch. ・The problem is not solved, even after the hand switch is removed. ■ Trouble of head key Cause) Failure of the head key When any button is kept pressed, Error 17 will occur.
Nemoto Kyorindo Co., Ltd. 6/4/2007
50
Service Manual 044-200133.06.03
044-200133.03
Dual Shot
Troubleshooting
6
However, syringe sensor buttons are excluded. Measure) Replace the head switch board. ■ Trouble of jog dial Cause) The jog dial does not return to the neutral position. Measure) Replace the jog dial. 6.2.13. ERR18 Error） Trouble of slit sensor (The rotation of ball screw is not detected, while the motor is rotating.) Cause） Failure of slit sensor Measure）Check the connection of the slit sensor system. If the slit sensor is broken, replace it. 6.2.14. ERR20 Error） Recieving fraudulently injected data Cause） Trouble of the head cable or loose connection of the cable in the console Measure）If the head cable is damaged, replace it. If the connector is not connected properly, reconnect it. 6.2.15. ERR30 Error） Wrong connection device Cause） A wrong head, a different one from the setting of the console, is connected. Measure）Set the console setting to match the head. Cause） The software version of the console is not compatible with that of the head. Measure）Change the software version of the console or the head to match. 6.2.16. ERR50 Error） The head can not be recognized, when the power is supplied. Cause） Defect of the head cable or loose connection of the wiring in the console Measure）If the head cable is damaged, replace it. If the connector is not connected properly, reconnect it. 6.2.17. ERR90 Error） Communication error between the console and the head. 6.2.18. ERR91 Error） Overrun
Service Manual 044-200133.06.03
51
Nemoto Kyorindo Co., Ltd. 6/4/2007
6
044-200133.03
Troubleshooting
Dual Shot
6.2.19. ERR92 Error） Framing error 6.2.20. ERR93 Error） Parity error 6.2.21. ERR95 Error） BCC error 6.2.22. ERR96 Error） Retry error Cause） Defect of the head cable, relay cable or loose contact of the connector Measure）Make sure that the cable connectors are correctly connected. Make sure that the connectors inside the head and console are firmly connected. Make sure that the cables are not abnormally stressed. (Make sure that no heavy objects are on the cable.) Make sure that the cable coating is not damaged. (In very rare cases, the cable is broken.)
Nemoto Kyorindo Co., Ltd. 6/4/2007
52
Service Manual 044-200133.06.03
044-200133.03
Dual Shot
Head Calibration
7
7. Head Calibration 7.1. Connection for Head Calibration
7.2. Configuration of Communication Software Use a Windows-standard hyper terminal as a communication software. Each set value is as shown below. Port ：com1 Bit/sec. ：19200 Data bit ：8 Parity ：none Stop bit ：1 Flow control：none
Service Manual 044-200133.07.03
53
Nemoto Kyorindo Co., Ltd. 6/4/2007
7
044-200133.03
Head Calibration
Dual Shot
7.3. Programming Procedure １）Activate the hyper terminal.
２）Input a name and select a desired icon.
Nemoto Kyorindo Co., Ltd. 6/4/2007
54
Service Manual 044-200133.07.03
044-200133.03
Dual Shot
Head Calibration
３） Select
４） Set
044-200133.07.03
55
“Direct to com1”.
each property.
５） Close
Service Manual
7
the “Hyper terminal.”
Nemoto Kyorindo Co., Ltd. 6/4/2007
7
044-200133.03
Head Calibration
Dual Shot
６） Select
the icon with the name you input and start the communication with the head
Nemoto Kyorindo Co., Ltd. 6/4/2007
56
Service Manual 044-200133.07.03
044-200133.03
Dual Shot
Head Calibration
7
7.4. Set for Programming Mode Set the dip switches of the head for programming mode. Turn No.1 dip switch in the direction of the arrow and turn the power on. Start communication with com1, and the head setting can be changed.
7.5. Pressure Offset Setting Offset of the pressure sensor is calibrated automatically. To perform automatic offset calibration of the pressure sensor: １）Set No.2 dip switch on the calibration board in the direction of the arrow. ２）Press the start switch of the head. ３）A short beep sounds in a few seconds to indicate completion of the calibration.
Service Manual 044-200133.07.03
57
Nemoto Kyorindo Co., Ltd. 6/4/2007
7
044-200133.03
Head Calibration
Dual Shot
7.6. List of Commands Command W
Saving the setting
E
Restoring the setting ＜ The status of when W was pressed is restored. ＞
I
Initialization of the setting ＜ The setting is changed to the defaults of the program. ＞
l
Display of the set values
[
Buzzer volume: up
]
Buzzer volume: down
+
SV_DBG: up (development use only)
-
SV_DBG: down (development use only)
m
Change of MT_DBG (development use only)
d
Pressure gain of A head: up
c
Pressure gain of A head: down
a
Pressure gain of B head: up
z
Pressure gain of B head: down
f
DA_DAT 0: up
v
DA_DAT 0: down
g
DA_DAT 1: up
h
DA_DAT 1: down
s
DA_DAT 2: up
x
DA_DAT 2: down
h
DA_DAT 3: up
n
DA_DAT 3: down
0
Calibration mode (zero: 0)
ESC
Halt of monitoring mode (waiting for command input)
o
Selection of pressure monitor for A head (o: lower-case letter)
p
Selecton of pressure monitor for B head
j
Change of head selection during jog dial operation
!
OFF/ON of low pressure warning
Nemoto Kyorindo Co., Ltd. 6/4/2007
Description
58
Service Manual 044-200133.07.03
044-200133.03
Dual Shot
Head Calibration
7
7.7. EEPROM Initialization Enter “I” (capital letter for i).
The screen above appears when the initialization completes.
7.8. Calibration Data Display Enter “l” (lower-case letter for L).
The calibration data currently set will be displayed.
Service Manual 044-200133.07.03
59
Nemoto Kyorindo Co., Ltd. 6/4/2007
7
044-200133.03
Head Calibration
Dual Shot
7.9. Front Limit Calibration
１）A head - When a 100ml syringe is mounted and the plunger is advanced to the front limit, the plunger should not come into close contact with the barrel at the front limit. ２）A head - With the 100mL setting, when the plunger is reversed to the rear limit it should indicate 105mL. ３）B head - When a syringe is mounted and the plunger is advanced to the front limit, the plunger should not come into close contact with the barrel at the front limit. ４）B head - With the 50mL setting, when the plunger is reversed to the rear limit, it should indicate 62mL.
Nemoto Kyorindo Co., Ltd. 6/4/2007
60
Service Manual 044-200133.07.03
044-200133.03
Dual Shot
Head Calibration
7
7.10. Offset Programming and Check of Electromagnetic Brake When programming offset, check operation of the electromagnetic brake.
１）Input zero “0”, and “Calibration Mode” is displayed.
２）Press the start switch of the head, and “Offset Was set” will be displayed.
Service Manual 044-200133.07.03
61
Nemoto Kyorindo Co., Ltd. 6/4/2007
7
044-200133.03
Head Calibration
Dual Shot
(Waiting for command input)
３）Input “ESC”, and “Return to Product Mode” wil be displayed.
(A: pressure monitor)
４）When “o” (lower-case letter for O) is input, “A:0000” will be repeatedly displayed. Press “ESC”, and displaying will stop and changes to the command waiting status.
Nemoto Kyorindo Co., Ltd. 6/4/2007
62
Service Manual 044-200133.07.03
044-200133.03
Dual Shot
Head Calibration
7
When “p” is input, “B:0000” is repeatedly displayed. When “ESC” is pressed, displaying stops. Ensure that the electromagnetic brake of the B head is working at this time.
To check the electromagnetic brake, pick the slit plate of the B head and verify that it does not turn.
Service Manual 044-200133.07.03
63
Nemoto Kyorindo Co., Ltd. 6/4/2007
7
044-200133.03
Head Calibration
Dual Shot
7.11. Jog Shuttle Programming
Every time “j” is input, the operation mode of the jog shuttle changes and the programmed mode is displayed. JOG: A (The jog shuttle activates only for A head.) JOG: A or B (When B head is used, B is supported.) (When A head only is used, A is supported.) JOG: B (The jog shuttle activates only for B head.)
7.12. Buzzer Volume Programming
The default is “007F”. The volume increases when “［” is input, and decreases when “］” is input. The setting range is from 0000 to 00FF.
Nemoto Kyorindo Co., Ltd. 6/4/2007
64
Service Manual 044-200133.07.03
044-200133.03
Dual Shot
Head Calibration
7
7.13. Pressure Gain Programming
Calibrate the A head and the B head so that the displayed pressure falls within ± 0.3 ㎏ /cm2 of the actual pressure. A head “d”: gain increases. “c”: gain decreases.
B head “a”: gain increases. “z”: gain decreases.
Service Manual 044-200133.07.03
65
Nemoto Kyorindo Co., Ltd. 6/4/2007
7
044-200133.03
Head Calibration
Dual Shot
7.14. Calibration Mode in General
To change the monitoring mode to the command input mode, press “ESC”.
Mandatory
To save the changes, always press “W”.
● Ensure to save the setting after change.
Nemoto Kyorindo Co., Ltd. 6/4/2007
66
Service Manual 044-200133.07.03
044-200133.03
Dual Shot
Head Calibration
7
7.15. Setting of Low Pressure Warning
“Det.LOW PRS.:ON” is changed into “Det.LOW PRS.:OFF” by pressing “!”. If “!” is pressed again, it will return to “Det.LOW PRS.:ON.” Low-pressure warning becomes valid by “Det.LOW PRS.:ON,” and low-pressure warning becomes invalid by “Det.LOW PRS.:OFF.”
Service Manual 044-200133.07.03
67
Nemoto Kyorindo Co., Ltd. 6/4/2007
7
044-200133.03
Head Calibration
Dual Shot
7.16. Offset/Pressure Display Adjustment from Console Open the cover on the rear side of the console while the regular injection setup screen is displayed. １）Turn ON the S-3 switch. ２）The offset gain adjustment screen will appear. ３）Make offset gain adjustment.
①
Nemoto Kyorindo Co., Ltd. 6/4/2007
68
Service Manual 044-200133.07.03
044-200133.03
Dual Shot
Head Calibration
7
The figure below shows the console display screen.
Press the + or - buttons on both sides of each item to modify. The set value becomes valid once the item is modified. To exit: Turn OFF the S-3switch. Turn ON/OFF the S-3 switch.
Service Manual 044-200133.07.03
69
Nemoto Kyorindo Co., Ltd. 6/4/2007
7
044-200133.03
Head Calibration
Nemoto Kyorindo Co., Ltd. 6/4/2007
Dual Shot
70
Service Manual 044-200133.07.03
044-200133.03
Dual Shot Alpha
Program Update
8
8. Program Update 8.1. Connection of Program Updating Jig
Service Manual 044-200133.08.03
71
Nemoto Kyorindo Co., Ltd. 6/4/2007
8
044-200133.03
Program Update
Dual Shot Alpha
8.2. Procedure of Program Change １）Activate “FLASH2” for Windows.
２）Ensure the setting of FLASH2.
Nemoto Kyorindo Co., Ltd. 6/4/2007
72
Service Manual 044-200133.08.03
044-200133.03
Dual Shot Alpha
Program Update
8
３）Select the updating file.
Service Manual 044-200133.08.03
73
Nemoto Kyorindo Co., Ltd. 6/4/2007
8
044-200133.03
Program Update
Dual Shot Alpha
４）Connect the head and the display. ５）Select “Execute”.
６）When the writing completes, the screen as shown below will be displayed.
７）When writing operation is completed, make sure to perform program initialization.
Nemoto Kyorindo Co., Ltd. 6/4/2007
74
Service Manual 044-200133.08.03
044-200133.03
Dual Shot Alpha
Program Update
8
8.3. Program Initialization
After the program change, shut down the power and turn ON the DIP switch 1 to reboot. Turn OFF the DIP switch 1 and then shut down the power. This operation registers the SUM of the program changed. If this operation is skipped, the injector will not work normally.
Service Manual 044-200133.08.03
75
Nemoto Kyorindo Co., Ltd. 6/4/2007
8
044-200133.03
Program Update
Nemoto Kyorindo Co., Ltd. 6/4/2007
Dual Shot Alpha
76
Service Manual 044-200133.08.03
044-200133.03
Dual Shot
Rewrite of Altera
9
9. Rewrite of Altera 9.1. Connection of Arutera Rewriting Jig
Service Manual 044-200133.09.03
77
Nemoto Kyorindo Co., Ltd. 6/4/2007
9
044-200133.03
Rewrite of Altera
Dual Shot
9.2. Rewriting Procedure １）Activate “MAX+Pluss Ⅱ .”
２）Select “JTAG.”
Nemoto Kyorindo Co., Ltd. 6/4/2007
78
Service Manual 044-200133.09.03
044-200133.03
Dual Shot
Rewrite of Altera
9
３）Press “Select Programming File.”
Service Manual 044-200133.09.03
79
Nemoto Kyorindo Co., Ltd. 6/4/2007
9
044-200133.03
Rewrite of Altera
Dual Shot
４）Select the programming file.
５）Use “Add” to add to the list.
Nemoto Kyorindo Co., Ltd. 6/4/2007
80
Service Manual 044-200133.09.03
044-200133.03
Dual Shot
Rewrite of Altera
9
６）Add necessary files to the list one by one.
７）Arrange the rewriting order of the programs.
Service Manual 044-200133.09.03
81
Nemoto Kyorindo Co., Ltd. 6/4/2007
9
044-200133.03
Rewrite of Altera
Dual Shot
８）Input (none) for the program requiring no change.
Input (none) to “Programming File Name” and press “Change.” Three writing files are always necessary.
９）Press “Yes” to switch to JTAG mode.
Nemoto Kyorindo Co., Ltd. 6/4/2007
82
Service Manual 044-200133.09.03
044-200133.03
Dual Shot
Rewrite of Altera
9
１０）Start writing.
Service Manual 044-200133.09.03
83
Nemoto Kyorindo Co., Ltd. 6/4/2007
9
044-200133.03
Rewrite of Altera
Dual Shot
9.3. Selection of Writing Tools １）Select “Option.”
２）Select the writing tool in “Hardware Setup.” “ByteBlaster” is selected in the example below.
Nemoto Kyorindo Co., Ltd. 6/4/2007
84
Service Manual 044-200133.09.03
001-100134.04
Dual Shot
Contact Information
10
10. Contact Information Authority Representative MMS MEDICOR MEDICAL SUPPLIES GmbH GWUBEUXG HWER AREAAW 6 50170 KERPEN GERMANY
Manufacturer NEMOTO KYORINDO CO., LTD. 2-27-20 HONGO, BUNKYO-KU TOKYO 113-0033 JAPAN
Service Manual 044-200133.10.03
85
Nemoto Kyorindo Co., Ltd. 6/4/2007
10
001-100134.04
Contact Information
Nemoto Kyorindo Co., Ltd. 6/4/2007
Dual Shot
86
Service Manual 044-200133.10.03
Dual Shot Revision History 2006/4/3 Revised date
Description
2004/01/30 First edition
Newly created
2006/4/3 044-200133.00.02
2nd edition Created on the base of the Japanese service manual of 081200133.00.05
Table of Manual Constitution 2006/4/3 044-200133.00.02
Document reference number 044-200133.00.02 044-200133.01.02 044-200133.02.02 044-200133.03.02 044-200133.04.02 044-200133.05.02 044-200133.06.02 044-200133.07.02 044-200133.08.02 044-200133.09.02
Modification
View more...
Comments
