Empowered by Innovation
INDOOR ACCESSORIES INSTALLATION MATERIAL RF ACCESSORIES MEASURING TOOLS ANTENNA for MICROWAVE RADIO
NEC Eastern Europe Ltd. (NEE)
Catalogue - release 2.0
PREFACE This catalogue introduces the product portfolio offered by NEC Eastern Europe Ltd. (NEE), mainly for NEC microwave equipment. These products include base-band connection interfaces, RF accessories, installation materials, measuring tools and specialized antenna types. All of these accessories were developed and manufactured based on specific customer requirements in accordance with the quality standards of NEC Corporation, compliance to which is being certified officially. NEE is always open to further product development requests from customers. Summary of the product groups: • Various I/O Board Sets for symmetrical and asymmetrical PDH signal distribution with special interconnection cables to fit all equipment types: iPASOLINK, PASOLINK NEO/s, NEO/c, NEO HP, NEO/a, NEO/TE, NEO/EXT, … • Cable assemblies for traffic, power or control signals • RF accessories: hybrids/couplers, OMTs, Adapters, coaxial cables, etc to further enhance NEC Microwave equipment configuration versatility (1+0, 1+1, 2+0, … system) • Installation material kits according to equipment types • Measuring tools and systems for test and demonstration purposes • Special antennas for particular requirements (single and dual polarization (with OMT included), with hydrophobic radome, heated antennas)
CONTENTS
PAGE
A INDOOR ACCESSORIES I/O board connection guide 1. I/O Board Sets 2. Cable Assemblies Pin layout information
4 7 16 19
B 3.
INSTALLATION MATERIAL Installation materials, installation material kits
20
C 4. 5. 6. 7. 8.
RF ACCESSORIES OMT (Ortho Mode Transducer) Hybrids 1. Hybrid for 2 ODUs 2. Hybrid for 4 ODUs Mounting bracket Waveguide-N Transducer Low Loss cable
D 9.
MEASURING TOOLS FOR LABORATORY PURPOSES Measuring tools
42
E 10.
ANTENNA Special antennas
44
GENERAL TERMS AND CONDITIONS
24 25 35 39 40 41
46
IO BOARD CONNECTION GUIDE A) I/O Board Set definition, E1 connector types
I/O Boards and Interconnection cables provide access to E1 traffic channels of PASOLINK equipment on specific connector types. The I/O Board is the unit with connectors and the Interconnection cables are the cable assemblies that connect IDU and I/O Board.
I/O Board(s) with relevant Interconnection cable(s) make an I/O Board Set. Numerous I/O Board Sets are available depending on capacity and connector types. Example: I/O Board Set for 16E1 with BNC connectors Part No.: NEC-IOBSET-N48-32M-BNC This I/O Board Set includes: • 1pc of 16E1 BNC I/O Board (NEC-IOB-32M-BNC) • 1pc of MDR-DSUB interconnection cable (NEC-TRCB-M68-STD)
E1 connectors on PASOLINK CONNECTOR TYPES
CAPACITY (max) 8E1
MDR68 connector
16E1
4
DSUB37 connector
IO BOARD CONNECTION GUIDE B) I/O Board Set Configuration To determine your I/O Board Set please follow the 2 step I/O Board Set configuration. Step 1: Please define the type and capacity of E1 connectors of your PASOLINK using this connector guide. Add main board capacity (if applicable) and interface card capacity.
Connector Guide IDU type
Main Board/Interface
Maximum capacity:
Type of E1 connector(s):
No. of E1 connectors (pcs):
iPASOLINK 400
Main Board
16E1
MDR68
1
iPASOLINK 400
16E1-A INTFC
16E1
MDR68
1
iPASOLINK 200
Main Board
16E1
MDR68
1
iPASOLINK 200
16E1-S INTFC
16E1
MDR68
1
NEO/s
16E1 INTFC with 2P LAN
16E1
DSUB37
2
NEO/s
16E1 INTFC with 2P LAN & 2way DXC
16E1
DSUB37
2
NEO/s
32E1 INTFC with 2P LAN
32E1
MDR68
2
NEO/s
48E1 INTFC
48E1
MDR68
3
NEO/s
4P LAN INTFC
8E1
DSUB37
1
NEO/s
4P LAN INTFC-E for VLAN & QoS
8E1
DSUB37
1
NEO/s
E3 INTFC
8E1
DSUB37
1
NEO/c 1+0 Fixed for E1, 5E1 Fixed
Main Board
5E1
DSUB37
1
NEO/c 1+0 Fixed for E1, 5/10/16E1
Main Board
16E1
DSUB37
2
NEO/c 1+0 Fixed, Expandable LAN, 5/10/16E1
Main Board
16E1
DSUB37
2
NEO/c 1+0 Expandable /1+1, 5/10/16E1
Main Board
16E1
DSUB37
2
NEO HP
16E1 + AMR INTFC
16E1
MDR68
1
NEO EXT
Main Board
16E1
MDR68
1
NEO EXT
E12_32 INTFC
32E1
MDR68
2
NEO/a
E1 INTFC
32E1
MDR68
2
NEO TE
32xE1/T1 TDM/ATM/EoPDH INTFC
32E1
MDR68
2
NEO TE
16xE1/T1 TDM/ATM INTFC
16E1
DSUB37
2
Tip: Capacity should be reconsidered if the E1 requirement is below the possible maximum capacity (and no expansion is planned).
5
IO BOARD CONNECTION GUIDE B) I/O Board Set Configuration Step 2: Please determine the preferred user connector type: RJ45, DSUB37, BNC, 1656, SMZ, SMB or 1023. Choosing (1) E1 connector type your IDU, (2) required capacity and (3) required user connector type, please move from left to right in the following table. As a result you will get the code and reference number of the I/O Board Set that you need for your PASOLINK E1 distribution. For more information on that I/O board Set please refer to the following chapter of the catalogue:
E1 connector (IDU)
Capacity
Required E1 connector (I/O Board)
I/O Board Set code
Item Reference
NEC-IOBSET-N48-32M-BNC
1.1.2
1.6/5.6
NEC-IOBSET-N48-32M-1656
1.2.2
SMZ (BT43
NEC-IOBSET-N48-32M-SMZ
1.3.2
BNC
16E1
MDR68
32E1
IDU 48E1
16E1
SMB
NEC-IOBSET-N48-32M-SMB
1.4.2
1.0/2.3
NEC-IOBSET-N48-32M-1023
1.5.2
RJ45
NEC-IOBSET-N48-32M-RJ45
1.6.2
DSUB37
NEC-IOBSET-N48-32M-DSUB
1.7.1
BNC
NEC-IOBSET-N48-2x32M-BNC
1.1.3
1.6/5.6
NEC-IOBSET-N48-2x32M-1656
1.2.3
SMZ (BT43
NEC-IOBSET-N48-2x32M-SMZ
1.3.3
SMB
NEC-IOBSET-N48-64M-SMB
1.4.3
1.0/2.3
NEC-IOBSET-N48-64M-1023
1.5.3
RJ45
NEC-IOBSET-N48-64M-RJ45
1.6.3
DSUB37
NEC-IOBSET-N48-64M-DSUB
1.7.2
BNC
NEC-IOBSET-N48-3x32M-BNC
1.1.4
1.6/5.6
NEC-IOBSET-N48-3x32M-1656
1.2.4
SMZ (BT43
NEC-IOBSET-N48-3x32M-SMZ
1.3.4
SMB
NEC-IOBSET-N48-96M-SMB
1.4.4
1.0/2.3
NEC-IOBSET-N48-96M-1023
1.5.4
RJ45
NEC-IOBSET-N48-96M-RJ45
1.6.4
DSUB37
NEC-IOBSET-N48-96M-DSUB
1.7.3
BNC
NEC-IOBSET-N16-32M-BNC
1.1.1
1.6/5.6
NEC-IOBSET-N16-32M-1656
1.2.1
SMZ (BT43
NEC-IOBSET-N16-32M-SMZ
1.3.1
SMB
NEC-IOBSET-N16-32M-SMB
1.4.1
1.0/2.3
NEC-IOBSET-N16-32M-1023
1.5.1
RJ45
NEC-IOBSET-N16-32M-RJ45
1.6.1
DSUB37
n/a
-
8E1
BNC
NEC-IOBSET-N16-16M-BNC
1.1.5
8E1
RJ45
NEC-IOBSET-N16-16M-RJ45
1.6.5
5E1
BNC
NEC-IOBSET-N16-10M-BNC
1.1.6
4E1
BNC
NEC-IOBSET-8M-BNC
1.1.7
DSUB37
*In case you don’t find the item that fits your demand, please contact us:
[email protected]
6
A. Indoor Accessories 1. I/O BOARD SETS 1.1 I/O Board Sets with BNC connectors
Part No.: NEC-IOB-32M-BNC; Capacity: 16E1; BNC socket connectors (32 pcs); 1U high, 2xDSUB37 plug connectors on the rear I/O Board Set for 16E1 with BNC connectors – (for IDU with DSUB37)
1.1.1
Part No: NEC-IOBSET-N16-32M-BNC Includes: 1x 16E1 BNC I/O Board (NEC-IOB-32M-BNC) + 2x DSUB37-DSUB-37 Interconnection cable (NEC-TRCB-D37-SCRW) I/O Board Set for 16E1 with BNC connectors – (for IDU with MDR68)
1.1.2
Part No.: NEC-IOBSET-N48-32M-BNC Includes: 1pc NEC-IOB-32M-BNC + 1pc NEC-TRCB-M68-STD I/O Board Set for 32E1 with BNC connectors
1.1.3
Part No.: NEC-IOBSET-N48-2x32M-BNC Includes: 2pcs NEC-IOB-32M-BNC + 2pcs NEC-TRCB-M68-STD I/O Board Set for 48E1 with BNC connectors
1.1.4
Part No: NEC-IOBSET-N48-3x32M-BNC Includes: 3pcs NEC-IOB-32M-BNC + 3pcs NEC-TRCB-M68-STD
7
A. Indoor Accessories 1. I/O BOARD SETS 1.1 I/O Board Sets with BNC connectors
Part No.: NEC-IOB-16M-BNC; Capacity: 8E1; BNC socket connectors (16 pcs); 1/2U high; 1xDSUB37 plug connectors on the rear I/O Board Set for 8E1 with BNC connectors
1.1.5
Part No: NEC-IOBSET-N16-16M-BNC Includes: 1pc NEC-IOB-16M-BNC + 1pc NEC-TRCB-D37-SCRW
Part No.: NEC-IOB-10M-BNC; Capacity: 5E1; BNC socket connectors (10 pcs); 1/2U high; 1xDSUB37 plug connectors on the rear I/O Board Set for 5E1 with BNC connectors
1.1.6
Part No: NEC-IOBSET-N16-10M-BNC Includes: 1pc NEC-IOB-10M-BNC + 1pc NEC-TRCB-D37-SCRW
Part No.: NEC-IOB-8M-BNC; Capacity: 4E1; BNC socket connectors (8 pcs); 1/2U high; 1xDSUB37 plug connectors on the rear I/O Board Set for 4E1 with BNC connectors
1.1.7
8
Part No: NEC-IOBSET-N16-8M-BNC Includes: 1pc NEC-IOB-8M-BNC + 1pc NEC-TRCB-D37-SCRW
A. Indoor Accessories 1. I/O BOARD SETS 1.2 I/O Board Sets with 1.6/5.6 connectors
Part No.: NEC-IOB-32M-1656; Capacity: 16E1; 1.6/5.6 socket connectors (32 pcs); 1U high; 2xDSUB37 plug connectors on the rear I/O Board Set for 16E1 with 1.6/5.6 connectors – (for IDU with DSUB37)
1.2.1
Part No: NEC-IOBSET-N16-32M-1656 Includes: 1pc NEC-IOB-32M-1656 +2pcs NEC-TRCB-D37-SCRW I/O Board Set for 16E1 with 1.6/5.6 connectors – (for IDU with MDR68)
1.2.2
Part No.: NEC-IOBSET-N48-32M-1656 Includes: 1pc NEC-IOB-32M-1656 + 1pc NEC-TRCB-M68-STD I/O Board Set for 32E1 with 1.6/5.6 connectors
1.2.3
Part No.: NEC-IOBSET-N48-2x32M-1656 Includes: 2pcs NEC-IOB-32M-1656 + 2pcs NEC-TRCB-M68-STD I/O Board Set for 48E1 with 1.6/5.6 connectors
1.2.4
Part No: NEC-IOBSET-N48-3x32M-1656 Includes: 3pcs NEC-IOB-32M-1656 + 3pcs NEC-TRCB-M68-STD
Note: I/O Board Sets with 1.6/5.6 connectors are also available for 8 / 5 / 4E1. 9
A. Indoor Accessories 1. I/O BOARD SETS 1.3 I/O Board Sets with SMZ connectors
Part No.: NEC-IOB-32M-SMZ; Capacity: 16E1; SMZ (BT43) male connectors (32 pcs); 1U high, 2xDSUB37 plug connectors on the rear I/O Board Set for 16E1 with SMZ connectors – (for IDU with DSUB37)
1.3.1
Part No: NEC-IOBSET-N16-32M-SMZ Includes: 1pc NEC-IOB-32M-SMZ + 2pcs NEC-TRCB-D37-SCRW I/O Board Set for 16E1 with SMZ connectors – (for IDU with MDR68)
1.3.2
Part No.: NEC-IOBSET-N48-32M-SMZ Includes: 1pc NEC-IOB-32M-SMZ + 1pc NEC-TRCB-M68-STD I/O Board Set for 32E1 with SMZ connectors
1.3.3
Part No.: NEC-IOBSET-N48-2x32M-SMZ Includes: 2pcs NEC-IOB-32M-SMZ + 2pcs NEC-TRCB-M68-STD I/O Board Set for 48E1 with SMZ connectors
1.3.4
10
Part No: NEC-IOBSET-N48-3x32M-SMZ Includes: 3pcs NEC-IOB-32M-SMZ + 3pcs NEC-TRCB-M68-STD
A. Indoor Accessories 1. I/O BOARD SETS 1.4 I/O Board Sets with SMB connectors
Part No.: NEC-IOB-32M-SMB; Capacity: 16E1; SMB male connectors (32 pcs); 1/2U high; 2xDSUB37 plug connectors on the rear I/O Board Set for 16E1 with SMB connectors – (for IDU with DSUB37)
1.4.1
Part No: NEC-IOBSET-N16-32M-SMB Includes: 1pc NEC-IOB-32M-SMB + 2pcs NEC-TRCB-D37-SCRW I/O Board Set for 16E1 with SMB connectors – (for IDU with MDR68)
1.4.2
Part No.: NEC-IOBSET-N48-32M-SMB Includes: 1pc NEC-IOB-32M-SMB + 1pc NEC-TRCB-M68-STD
Part No.: NEC-IOB-64M-SMB; Capacity: 32E1; SMB male connectors (64 pcs); 1U high; 4xDSUB37 plug connectors on the rear I/O Board Set for 32E1 with SMB connectors
1.4.3
Part No.: NEC-IOBSET-N48-64M-SMB Includes: 1pc NEC-IOB-64M-SMB + 2pcs NEC-TRCB-M68-STD
Part No.: NEC-IOB-96M-SMB; Capacity: 48E1; SMB male connectors (96 pcs); 1U high; 6xDSUB37 plug connectors on the rear I/O Board Set for 48E1 with SMB connectors
1.4.4
Part No.: NEC-IOBSET-N48-96M-SMB Includes: 1pc NEC-IOB-96M-SMB + 3pcs NEC-TRCB-M68-STD
11
A. Indoor Accessories 1. I/O BOARD SETS 1.5 I/O Board Sets with 1.0/2.3 connectors
Part No.: NEC-IOB-32M-1023; Capacity: 16E1; 1.0/2.3 socket connectors (32 pcs); 1/2U high; 2xDSUB37 plug connectors on the rear I/O Board Set for 16E1 with 1.0/2.3 connectors – (for IDU with DSUB37)
1.5.1
Part No: NEC-IOBSET-N16-32M-1023 Includes: 1pc NEC-IOB-32M-1023 + 2pcs NEC-TRCB-D37-SCRW I/O Board Set for 16E1 with 1.0/2.3 connectors – (for IDU with MDR68)
1.5.2
Part No.: NEC-IOBSET-N48-32M-1023 Includes: 1pc NEC-IOB-32M-1023 + 1pc NEC-TRCB-M68-STD
Part No.: NEC-IOB-64M-1023; Capacity: 32E1; 1.0/2.3 socket connectors (64 pcs); 1U high; 4xDSUB37 plug connectors on the rear I/O Board Set for 32E1 with 1.0/2.3 connectors
1.5.3
Part No.: NEC-IOBSET-N48-64M-1023 Includes: 1pc NEC-IOB-64M-1023 + 2pcs NEC-TRCB-M68-STD
Part No.: NEC-IOB-96M-1023; Capacity: 48E1; 1.0/2.3 socket connectors (96 pcs); 1U high; 6xDSUB37 plug connectors on the rear I/O Board Set for 48E1 with 1.0/2.3 connectors
1.5.4
12
Part No.: NEC-IOBSET-N48-96M-1023 Includes: 1pc NEC-IOB-96M-1023 + 3pcs NEC-TRCB-M68-STD
A. Indoor Accessories 1. I/O BOARD SETS 1.6 I/O Board Sets with RJ45 connectors
Part No.: NEC-IOB-32M-RJ45; Capacity: 16E1; RJ45 socket connectors (16 pcs); 1/2U high, 2xDSUB37 plug connectors on the rear I/O Board Set for 16E1 with RJ45 connectors – (for IDU with DSUB37)
1.6.1
Part No: NEC-IOBSET-N16-32M-RJ45 Includes: 1pc NEC-IOB-32M-RJ45 + 2pcs NEC-TRCB-D37-SCRW I/O Board Set for 16E1 with RJ45 connectors – (for IDU with MDR68)
1.6.2
Part No.: NEC-IOBSET-N48-32M-RJ45 Includes: 1pc NEC-IOB-32M-RJ45 + 1pc NEC-TRCB-M68-STD
Part No.: NEC-IOB-64M-RJ45; Capacity: 32E1; RJ45 socket connectors (32 pcs); 1U high; 4xDSUB37 plug connectors on the rear I/O Board Set for 32E1 with RJ45 connectors
1.6.3
Part No.: NEC-IOBSET-N48-64M-RJ45 Includes: 1pc NEC-IOB-64M-RJ45 + 2pcs NEC-TRCB-M68-STD
Part No.: NEC-IOB-96M-RJ45; Capacity: 48E1; RJ45 socket connectors (48 pcs); 1U high; 6xDSUB37 plug connectors on the rear I/O Board Set for 48E1 with RJ45 connectors
1.6.4
Part No.: NEC-IOBSET-N48-96M-RJ45 Includes: 1pc NEC-IOB-96M-RJ45 + 3pcs NEC-TRCB-M68-STD
13
A. Indoor Accessories 1. I/O BOARD SETS 1.6 I/O Board Sets with RJ45 connectors
Part No.: NEC-IOB-16M-RJ45; Capacity: 8E1; RJ45 socket connectors (8 pcs); 1/2U high, 1xDSUB37 plug connectors on the rear I/O Board Set for 8E1 with RJ45 connectors
1.6.5
Part No: NEC-IOBSET-N16-16M-RJ45 Includes: 1pc NEC-IOB-16M-RJ45 + 1pc NEC-TRCB-D37-SCRW
MDR-RJ45 4E1 I/O adapter
1.6.6
Part No.: NEC-IOA-M68-4xRJ45-4E1 Capacity: 4E1; RJ45 socket connectors (4pcs); Direct mount – no rack space needed MDR-RJ45 8E1 I/O adapter
1.6.7
14
Part No.: NEC-IOA-M68-4xRJ45-8E1 Capacity: 8E1; RJ45 socket connectors (4pcs); Direct mount – no rack space needed; 2E1 channels/RJ45 connector
A. Indoor Accessories 1. I/O BOARD SETS 1.7 I/O Board Sets with DSUB connectors
Part No.: NEC-IOB-96M-DSUB; Fixing frame for MDR-DSUB interconnection cables. Capacity: 48E1; 6xDSUB37 cut-outs; 1/2U high I/O Board Set for 16E1 with DSUB connectors
1.7.1
Part No: NEC-IOBSET-N48-32M-DSUB Includes: 1pc NEC-IOB-96M-DSUB + 1pcs NEC-TRCB-M68-STD I/O Board Set for 32E1 with DSUB connectors
1.7.2
Part No.: NEC-IOBSET-N48-64M-DSUB Includes: 1pc NEC-IOB-96M-DSUB + 2pcs NEC-TRCB-M68-STD I/O Board Set for 48E1 with DSUB connectors
1.7.3
Part No.: NEC-IOBSET-N48-96M-DSUB Includes: 1pc NEC-IOB-96M-DSUB + 3pcs NEC-TRCB-M68-STD
All I/O board Sets are RoHS and REACH compliant and 19’ rack compatible. Customized I/O board sets can be developed upon request. Please contact NEC Eastern Europe Ltd:
[email protected]. 15
B. INSTALLATION A. Indoor Accessories MATERIAL 2. CABLES ASSEMBLIES
DSUB37-DSUB37 interconnection cable for 8E1
2.1
For connecting I/O Board to IDU (e.g. PASOLINK NEO/s - 16E1 INTFC+2P LAN) • Capacity: 8E1 • Connectors: DSUB37 plug (IDU side), DSUB37 socket (I/O Board side) • DSUB37 socket with locking screws (inch type) • 1m length
MDR68-2xDSUB37 interconnection cable for 16E1
2.2
For Back to Back connections of IDUs • Capacity: 16E1 • Connectors: 2xMDR68 plug • 0,5m length
16
Part No: NEC-TRCB-M68/2-STD
For connecting I/O Board to IDU (e.g. iPASOLINK 200; if maximum 8E1 is utilized of 16E1) • Capacity: 8E1 • Connectors: MDR68 plug (IDU side), DSUB37 socket (I/O Board side) • DSUB37 socket with locking screws / stumps (inch type) • 1m length
MDR68-MDR68 back to back cable - 0.5m
2.4
Part No: NEC-TRCB-M68-STD
For connecting I/O Board to IDU (e.g. iPASOLINK200, PASOLINK NEO/s – 48E1 INTFC) • Capacity: 16E1 • Connectors: MDR68 plug (IDU side), 2xDSUB37 socket (I/O Board side) • DSUB37 socket with locking screws / stumps (inch type) • 1m length
MDR68-DSUB37 interconnection cable for 8E1
2.3
Part No: NEC-TRCB-D37-SCRW
Part No: NEC-TRCB-M68-X-M68-0,5
B. INSTALLATION A. Indoor Accessories MATERIAL 2. CABLES ASSEMBLIES
MDR68–32 Twisted Pair-open end cable for 16E1
2.5
For IDU to DDF connections (Krone DDF or similar) • Capacity: 16E1 • Cable: 120 Ohm, 32 twisted pair, 26 AWG (0,4mm solid wire) • Connector: MDR68 plug • 10m length (custom length available upon request)
MDR68–MDR68 cable for IDU to DDF (Krone) applications, for 16E1
2.6
Part No: NEC-TRCB-D37-16TP-5
For IDU to DDF connections (Krone DDF or similar) • Capacity: 8E1 • Cable: 120 Ohm, 16 twisted pair, 26 AWG (0,4mm solid wire) • Connector: DSUB37 plug • 5m length (custom length available upon request)
NEO XPIC Cable Set (1+0)
2.8
Part No: NEC-TRCB-M68-32TP-5(X2)
For IDU to DDF connections (Krone DDF or similar). Indeed, it is an enhancement of MDR68 - open-end cable product: „2 in 1” for flexibility to define lenght at site. Cut cable at the appropriate length to have 2pcs of MDR-open end cables. You can decide cable length according to your requirement: 2x5m, 4m+6m, etc. • Capacity: 16E1; Connector; 2xMDR68 plug • Cable: 120 Ohm, 32 twisted pair, 26 AWG (0,4mm solid wire); 10m length (other length available upon request)
DSUB37– 16 twisted pair – open end cable for 8E1
2.7
Part No: NEC-TRCB-M68-32TP-10
Part No: NEC-XCBSET-NEO(1+0)-0,4
For PASOLINK NEO XPIC cabling (1+0) (Note: for 1+1 configuration, 2 XPIC cable sets are necessary per terminal) • CTRL cable assembly: DSUB15HD plug – DSUB15HD plug (1pc) • XIF cable assemblies: 1.0/2.3 plug – 1.0/2.3 plug (2pcs, auto locking type connectors) • 0,4m length
17
B. INSTALLATION A. Indoor Accessories MATERIAL 2. CABLES ASSEMBLIES
XPIC Cable for iPASOLINK 400
2.9
For iPASOLINK 400 XPIC cabling (Note: 2pcs of cables needed for one terminal, 1+0) • XIF cable assembly: 1.0/2.3 plug – 1.0/2.3 plug (2pcs, auto locking type connectors) • 0,4m length
DSUB37– 8 cores coax – open end cable for 4E1 / 8E1
2.10
For IDU to DDF connections • Capacity: 4E1 / 8E1 • Cable: 8 / 16 cores coaxial, 75 Ohm • Connectors: DSUB37 plug, 8 / 16 x1.6/5.6 socket • 2m length (custom length available upon request)
All cables are RoHS and REACH compliant. Customized cables can be developed upon request. Please contact NEC Eastern Europe Ltd:
[email protected] 18
Part No: NEC-TRCB-D37-8C-2 / NEC-TRCB-D37-16C-2
For IDU to DDF connections • Capacity: 4E1 / 8E1 • Cable: 8 / 16 cores coaxial, 75 Ohm • Connector: DSUB37 plug • 2m length (custom length available upon request)
DSUB37– 8 cores coax – 8 / 16x1.6/5.6 cable for 4E1 / 8E1
2.11
Part No: NEC-XCB-1023-0,4
Part No: NEC-TRCB-D37-8C-1656-2 / NEC-TRCB-D37-16C-1656-2
B. INSTALLATION A. Indoor Accessories MATERIAL PIN LAYOUT INFORMATION D-SUB 1
D-SUB 2
D-SUB 3
D-SUB 4
D-SUB 5
D-SUB 6
CH1-8
CH9-16
CH17-24
CH25-32
CH33-40
CH41-48
CH8
CH16
CH7
CH15
CH6
CH32
CH23
CH14
CH40
CH31
CH22
CH48
CH39
CH30
IN
CH47
CH38
pin:
IN
CH46
IN
CH5
CH13
CH21
CH29
CH37
CH45
IN
CH4
CH12
CH20
CH28
CH36
CH44
IN
CH3
CH11
CH19
CH27
CH35
CH43
IN
CH2
CH10
CH1
PASOLINK Traffic Channels
CH24
DSUB37 socket
CH18
CH9
CH8
CH17
CH16
CH7
CH5
CH13
CH4
CH21
CH12
CH3
CH20
CH11
CH2
CH19
CH10
CH1
CH18
CH9
CH17
OUT
CH43
CH34
CH25
OUT
CH44
CH35
CH26
OUT
CH45
CH36
CH27
OUT
CH46
CH37
CH28
OUT
CH47
CH38
CH29
IN
CH48
CH39
CH30
IN
CH41
CH40
CH31
CH22
CH42
CH33
CH32
CH23
CH14
CH34
CH25
CH24
CH15
CH6
CH26
OUT
CH42
CH33
OUT
CH41
OUT
+
1
-
2
+
3
-
4
+
6
-
7
+
8
-
9
+
11
-
12
+
13
-
14
+
16
-
17
+
18
-
19
+
20
-
21
+
22
-
23
+
25
-
26
+
27
-
28
+
29
-
30
+
31
-
32
+
34
-
35
+
36
-
37
ground
Cable types: MDR68-2xDSUB37 interconnection cable (NEC-TRCB-M68-STD) MDR68-DSUB37 interconnection cable (NEC-TRCB-M68/2-STD)
5
Specification: Pin layout is equal to the standard pin layout of PASOLINK DSUB37 traffic connectors ( e.g. DSUB37 traffic connectors of PASOLINK NEO - 16E1 INTFC+2P LAN, etc.)
Cable colour code of MDR68 - 32 twisted pair – open end cable (NEC-TRCB-M68-32TP-10) IN
CH1
CH3
CH5
CH7
CH9
CH11
CH16 BLUE
GREEN
CH14
ORANGE
CH12 YELLOW
CH10 BROWN
CH8 BLACK
CH6 GRAY
CH4 RED
CH2
CH13
OUT IN
CH15 OUT
-
BLUE
+
WHITE
-
ORANGE
+
WHITE
-
GREEN
+
WHITE
-
BROWN
+
WHITE
BL/W O/W G/W BR/W
Pin layout of RJ45 socket connectors on RJ45 I/O Boards One RJ45 connector corresponds to an E1 channel IN and OUT IN CH OUT
-
1
+
2
-
4
+
5
RJ45
19
B. INSTALLATION MATERIAL 3. INSTALLATION MATERIALS, INSTALLATION MATERIAL KITS
N-TNC IF jumper cable
Part No: NEC-JCB-N1-2
For IF interconnection • Connectors: 1x TNC right angle plug - 1x N straight plug, • 2m length
3.1
N-N ADAPTER
Part No: NEC-ADR-N(S)-N(S)
For IF interconnection • Interfaces: 2x N socket • Can be fixed in the IF fixing frame (see below 3.4)
3.2
LIGHTNING PROTECTOR
Part No: NEC-LGP-N(P)-N(S)
For IF interconnection • Maximum discharge current: 20kA • With self-extinguishing GDT (gas discharge tube) • Interfaces: 1x N plug, 1x N socket
3.3
IF FIXING FRAME For IF interconnection • Recessed design • For fixing of N-N adapter (see above) • 10 positions
3.4
20
Part No: NEC-IFF-NN-10P
B. INSTALLATION MATERIAL 3. INSTALLATION MATERIALS, INSTALLATION MATERIAL KITS
N-TNC IF jumper cable + N-N adapter (3.1 + 3.2)
Part No: NEC-JCBSET-N1-2
IF interconnection set, including: • Cable assembly: TNC right angle plug - N straight plug, 2m • Adapter: N socket – N socket
3.5
N-TNC IF jumper cable + N-N adapter + IF fixing frame (3.1 + 3.2 + 3.4)
3.6
IF interconnection set, including: • Cable assembly: TNC right angle plug - N straight plug, 2m • Adapter: N socket – N socket • IF fixing frame with 10 positions
N-TNC IF jumper cable + N-N adapter + Lightning protector + IF fixing frame (3.1 + 3.2 + 3.3 + 3.4)
3.7
Part No: NEC-JCBSET-N2-2
Part No:NEC-JCBSET-N3-2
IF interconnection set, including: • Cable assembly: TNC right angle plug - N straight plug, 2m • Adapter: N socket – N socket • Lightning protector (N plug – N socket) • IF fixing frame with 10 positions
21
B. INSTALLATION MATERIAL 3. INSTALLATION MATERIALS, INSTALLATION MATERIAL KITS
INSTALLATION MATERIAL KIT FOR PASOLINK NEO (1+0)
3.8
Installation material kit, including: • 1x 10m power cable with Molex power connector (+ pre-insulated terminals; 2x0,75mm2) • 1x 3m grounding cable for IDU (+ pre-insulated terminals; 6mm2) • 1x 3m grounding cable for ODU (+ terminals; 16mm2) • 100x Cable ties for indoor and outdoor, • 4x Screw kits for IDU mounting • 1x Self-fusing sealing compound for ODU connector • 1x PVC tape roll, 2x Cable marker • 1x 3m LCT cable (USB A – USB B) • 1x 10m LAN cable for NMS (+ RJ45 connectors)
INSTALLATION MATERIAL KIT FOR PASOLINK NEO (1+1)
3.9
22
Part No: .: NEC-IMK-I2/4-1PS
Installation material kit, including: • 1x 10m power cable with AMP power connector (+ pre insulated terminals; 2x0,75mm2) • 1x 3m grounding cable for IDU (+ pre-insulated terminals; 6mm2) • 1x 3m Grounding cable for ODU (+ terminals; 16mm2) • 100x Cable ties for indoor and outdoor, • 4x Screw kits for IDU mounting • 1x Self-fusing sealing compound for ODU connector • 1x PVC tape roll, 2x Cable marker • 1x 3m LCT cable (RJ45 - RJ45) • 1x 10m LAN cable for NMS (+ RJ45 connectors)
INSTALLATION MATERIAL KIT FOR iPASOLINK200/400 & 1000 (2 power line inlet)
3.11
Part No: NEC-IMK-NEO(1+1)
Installation material kit, including: • 2x 10m power cable with Molex power connector (+ pre insulated terminals; 2x0,75mm2) • 2x3m grounding cable for IDU (+ pre-insulated terminals; 6mm2) • 2x 3m grounding cable for ODU (+ terminals; 16mm2) • 100x Cable ties for indoor and outdoor, • 4x Screw kits for IDU mounting • 2x Self-fusing sealing compound for ODU connector • 2x PVC tape rolls, 2x Cable marker • 1x 3m LCT cable (USB A – USB B) • 1x 10m LAN cable for NMS (+ RJ45 connectors)
INSTALLATION MATERIAL KIT FOR iPASOLINK200/400 (1 power line inlet)
3.10
Part No: NEC-IMK-NEO(1+0)
Part No: NEC-IMK-I2/4-2PS – iPASOLINK200/400 NEC-IMK-I1000-2PS – iPASOLINK1000
Installation material kit, including: • 2x 10m power cable with AMP power connector (+ pre insulated terminals; 2x0,75mm2) • 2x 3m grounding cable for IDU (+ pre-insulated terminals; 6mm2) • 2x 3m Grounding cable for ODU (+ terminals; 16mm2) • 100x Cable ties for indoor and outdoor, • 4x Screw kits for IDU mounting • 2x Self-fusing sealing compound for ODU connector • 2x PVC tape rolls, 2x Cable marker • 1x 3m LCT cable (RJ45 - RJ45) • 1x 10m LAN cable for NMS (+ RJ45 connectors)
B. INSTALLATION MATERIAL 3. INSTALLATION MATERIALS, INSTALLATION MATERIAL KITS
10m power cable with Molex connector
Part No: NEC-PWCB-MOLEX-2x0,75-10
For power cabling of PASOLINK family (except for NEO/a) • Mini-Fit 4,2mm 4P connector • MT 2x0,75mm2 power cable • 10 m length (5 m length also available upon request)
3.12
10m power cable with AMP connector
Part No: NEC-PWCB-AMP-2x0,75-10
For power cabling of iPASOLINK family • AMP Dinamic 4P connector • MT 2x0,75mm2 power cable • 10 m length (5 m length also available upon request)
3.13
Optional Installation Materials For (i)PASOLINK family
Part No: NEC-IMOP-H-2…10
Hangers (up to 10 holes)
3.14
Optional Installation Materials For (i)PASOLINK family
Part No: NEC-IMOP-MCB
6A 48VDC Miniature Circuit Breaker
3.15
23
C. RF ACCESSORIES 4. ORTHO MODE TRANSDUCERS
Part No: OMT-110…380-2NEC-(G)(R)
OMT for 11-38GHz
Ortho Mode Transducer for Grante or RFS antenna for frequency range of 11, 13, 15, 18, 23, 26, 28, 32, 38GHz. The antenna type has to be specified in the purchase order for OMT. • Interface at ODU side: 2xNEC flange • Interface at Antenna side: interface for dual polarized Grante(G) or RFS(R) • Content of the ordering code: OMT-”frequency band”-2NEC-”Antenna manufacturer” • Example code: OMT-180-2NEC-R
4.1 4.9
Electrical Specification Operating Frequency Band
Operating Frequency Range
Insertion Loss
Inter-Port Isolation
Return Loss
11 GHz
10.700–11.700 GHz
0.6 dB
40 dB
–19.1 dB
13 GHz
12.750–13.250 GHz
0.6 dB
40 dB
–19.1 dB
15 GHz
14.200–15.350 GHz
0.6 dB
40 dB
–19.1 dB
18 GHz
17.700–19.700 GHz
0.6 dB
40 dB
–19.1 dB
23 GHz
21.200–23.600 GHz
0.6 dB
40 dB
–19.1 dB
26 GHz
24.500–26.500 GHz
0.8 dB
38 dB
–19.1 dB
28 GHz
27.500–29.500 GHz
1.0 dB
36 dB
–19.1 dB
32 GHz
31.000–33.400 GHz
1.0 dB
36 dB
–19.1 dB
37.000–39.500 GHz
1.0 dB
36 dB
–19.1 dB
38 GHz Interface (Antenna Side):
Upon Customer’s Request
Interface2 (ODU Side):
Upon Customer’s Request
1
Mechanical Specification Net Weight3
3.4 kg
Material
Aluminium
Remarks: 1) Direct mounting is possible for several types of antennas (from several manufacturers) with circular waveguide connector. 2) Coaxial cable connector, standard waveguide flange or any ODU interface is available upon request. 3) Approximate value (net weight depends on the required interfaces).
24
C. RF ACCESSORIES 5. HYBRID COMBINERS 5.1 HYBRIDS FOR 2 ODUs 5.1.1 ISH 6/7/8 GHz Hybrids for 2 ODUs with N connector
Integrated Single Polarized Symmetrical (3dB) or Asymmetrical (6 or 10dB) Single Band Hybrid for Frequency Range of 6-L GHz (5.925-6.425GHz) Part No: ISH-59-2N-3(6)(10)-P(U)D(B)R70-A(B)
5.1.1.1
• • • • • • •
Interfaces at ODU side: 2xN female Interface at antenna side: PDR70, UDR70, PBR70, UBR70 or other, according to customer request Material of the Waveguide flange: (A) - Aluminium or (B) Brass Content of the ordering code: ISH-59-2N-”coupling rate”-”waveguide flange”- “material of the WG flange” Example code: ISH-59-2N-3-UDR70-B Available in left (TL) and right (TR) mountable (mirrored) design for mounting on dual polarized antennas with standard waveguide flanges. Example code: ISH-59-2N-6-UBR70-A-TR
Integrated Single Polarized Symmetrical (3dB) or Asymmetrical (6 or 10dB) Single Band Hybrid for Frequency Range of 6-U GHz (6.425-7.125GHz) Part No: ISH-64-2N-3(6)(10)-P(U)D(B)R70-A(B)
5.1.1.2
• • • • • • •
Interfaces at ODU side: 2xN female Interface at antenna side: PDR70, UDR70, PBR70, UBR70 or other, according to customer request Material of the Waveguide flange: (A) - Aluminium or (B) Brass Content of the ordering code: ISH-64-2N-”coupling rate”-”waveguide flange”-”material of the WG flange” Example code: ISH-64-2N-3-UDR70-B Available in left (TL) and right (TR) mountable (mirrored) design for mounting on dual polarized antennas with standard waveguide flanges. Example code: ISH-64-2N-6-UDR70-B-TL
Integrated Single Polarized Symmetrical (3dB) or Asymmetrical (6 or 10dB) Single Band Hybrid for Frequency Range of 7 GHz (7.125-7.750GHz) Part No: ISH-71-2N-3(6)(10)-P(U)D(B)R84-A(B)
5.1.1.3
• • • • • • •
Interfaces at ODU side: 2xN female Interface at antenna side: PDR70, UDR70, PBR70, UBR70 or other, according to customer request Material of the Waveguide flange: (A) - Aluminium or (B) Brass Content of the ordering code: ISH-64-2N-”coupling rate”-”waveguide flange”-”material of the WG flange” Example code: ISH-64-2N-3-UDR70-B Available in left (TL) and right (TR) mountable (mirrored) design for mounting on dual polarized antennas with standard waveguide flanges. Example code: ISH-64-2N-6-UDR70-B-TL
25
C. RF ACCESSORIES 5. HYBRID COMBINERS 5.1 HYBRIDS FOR 2 ODUs 5.1.1 ISH 6/7/8 GHz Hybrids for 2 ODUs with N connector Integrated Single Polarized Symmetrical (3dB) or Asymmetrical (6 or 10dB) Single Band Hybrid for Frequency Range of 8 GHz (7.750-8.5GHz) Part No: ISH-77-2N-3(6)(10)-P(U)D(B)R84-A(B)
5.1.1.4
• • • • • • •
Interfaces at ODU side: 2xN female Interface at antenna side: PDR84, UDR84, PBR84, UBR84 or other, according to customer request Material of the Waveguide flange: (A) - Aluminium or (B) Brass Content of the ordering code: ISH-77-2N-”coupling rate”-”waveguide flange”-”material of the WG flange” Example code: ISH-77-2N-3-UDR84-A Available in left (TL) and right (TR) mountable (mirrored) design for mounting on dual polarized antennas with standard waveguide flanges. Example code: ISH-77-2N-3-UBR84-A-TL
Integrated Single Polarized Symmetrical (3dB) or Asymmetrical (6 or 10dB) Dual Band Hybrid for Frequency Range of 6-W GHz (5.925-7.125GHz) Part No: ISH-59-71-2N-3(6)(10)-P(U)D(B)R70-A(B)
5.1.1.5
• • • • •
Interfaces at ODU side: 2xN female Interface at antenna side: PDR70, UDR70, PBR70, UBR70 or other, according to customer request Material of the Waveguide flange: (A) - Aluminium or (B) Brass Content of the ordering code: ISH-59-71-2N-”coupling rate”-”waveguide flange”-”material of the WG flange” Example code: ISH-59-71-2N-3-UDR70-B
Integrated Single Polarized Symmetrical (3dB) or Asymmetrical (6 or 10dB) Dual Band Hybrid for Frequency Range of 7-8 GHz (7.125-8.5GHz) Part No: ISH-71-85-2N-3(6)(10)-P(U)D(B)R84-A(B)
5.1.1.6
26
• • • • •
Interfaces at ODU side: 2xN female Interface at antenna side: PDR84, UDR84, PBR84, UBR84 or other, according to customer request Material of the Waveguide flange: (A) - Aluminium or (B) Brass Content of the ordering code: ISH-71-85-2N-”coupling rate”-”waveguide flange”-”material of the WG flange” Example code: ISH-71-85-2N-10-UDR84-B
C. RF ACCESSORIES 5. HYBRID COMBINERS 5.1 HYBRIDS FOR 2 ODUs 5.1.2 ISH 6/7/8 GHz Hybrids for 2 ODUs with waveguide flange
Integrated Single Polarized Symmetrical (3dB) or Asymmetrical (6 or 10dB) Single Band Hybrid for Frequency Range of 6-L GHz (5.925-6.425GHz) Part No: ISH-59-2P(U)D(B)R70(A(B))-3(6)(10)-P(U)D(B)R70(A(B))
5.1.2.1
• • • • • • •
Interfaces at ODU side: 2xPDR70, 2xUDR70, 2xPBR70, 2xUBR70 or others, according to customer request Interface at antenna side: PDR70, UDR70, PBR70, UBR70 or other, according to customer request Material of the Waveguide flanges: (A) - Aluminium or (B) Brass Content of the ordering code: ISH-59-2”waveguide flange at antenna side”-”coupling rate”-”waveguide flange at ODU side” Example code: ISH-59-2UDR70(A)-3-UDR70(B) Available in left (TL) and right (TR) mountable (mirrored) design for mounting on dual polarized antennas with standard waveguide flanges Example code: ISH-59-2PDR70(A)-6-UBR70(A)-TL
Integrated Single Polarized Symmetrical (3dB) or Asymmetrical (6 or 10dB) Single Band Hybrid for Frequency Range of 6-U GHz (6.425-7.125GHz) Part No: ISH-64-2P(U)D(B)R70(A(B))-3(6)(10)-P(U)D(B)R70(A(B))
5.1.2.2
• • • • • • •
Interfaces at ODU side: 2xPDR70, 2xUDR70, 2xPBR70, 2xUBR70 or others, according to customer request Interface at antenna side: PDR70, UDR70, PBR70, UBR70 or other, according to customer request Material of the Waveguide flanges: (A) - Aluminium or (B) Brass Content of the ordering code: ISH-64-2”waveguide flange at antenna side”-”coupling rate”-”waveguide flange at ODU side” Example code: ISH-64-2PDR70(A)-3-UDR70(B) Available in left (TL) and right (TR) mountable (mirrored) design for mounting on dual polarized antennas with standard waveguide flanges Example code: ISH-64-2UDR70(A)-6-UDR70(A)-TR
Integrated Single Polarized Symmetrical (3dB) or Asymmetrical (6 or 10dB) Single Band Hybrid for Frequency Range of 7 GHz (7.125-7.750GHz) Part No: .: ISH-71-2P(U)D(B)R84(A(B))-3(6)(10)-P(U)D(B)R84(A(B))
5.1.2.3
• • • • • • •
Interfaces at ODU side: 2xPDR84, 2xUDR84, 2xPBR84, 2xUBR84 or other, according to customer request Interface at antenna side: PDR84, UDR84, PBR84, UBR84 or other, according to customer request Material of the Waveguide flanges: (A) - Aluminium or (B) Brass Content of the ordering code: ISH-71-2”waveguide flange at antenna side”-”coupling rate”-”waveguide flange at ODU side” Example code: ISH-71-2UBR84(A)-3-UDR84(A) Available in left (TL) and right (TR) mountable (mirrored) design for mounting on dual polarized antennas with standard waveguide flanges Example code: ISH-71-2PBR84(A)-3-UBR84(B)-TR
27
C. RF ACCESSORIES 5. HYBRID COMBINERS 5.1 HYBRIDS FOR 2 ODUs 5.1.2 ISH 6/7/8 GHz Hybrids for 2 ODUs with waveguide flange Integrated Single Polarized Symmetrical (3dB) or Asymmetrical (6 or 10dB) Single Band Hybrid for Frequency Range of 8 GHz (7.750-8.5GHz) Part No: ISH-77-2P(U)D(B)R84(A(B))-3(6)(10)-P(U)D(B)R84(A(B))
5.1.2.4
• • • • • • •
Interfaces at ODU side: 2xPDR84, 2xUDR84, 2xPBR84, 2xUBR84 or other, according to customer request Interface at antenna side: PDR84, UDR84, PBR84, UBR84 or other, according to customer request Material of the Waveguide flanges: (A) - Aluminium or (B) Brass Content of the ordering code: ISH-77-2”waveguide flange at antenna side”-”coupling rate”-”waveguide flange at ODU side” Example code: ISH-77-2PDR84(A)-3-UDR84(A) Available in left (TL) and right (TR) mountable (mirrored) design for mounting on dual polarized antennas with standard waveguide flanges Example code: ISH-77-2PDR84(A)-3-UBR84(A)-TR
Integrated Single Polarized Symmetrical (3dB) or Asymmetrical (6 or 10dB) Dual Band Hybrid for Frequency Range of 6-W GHz (5.925-7.125GHz) Part No: ISH-59-71-2P(U)D(B)R70(A(B))-3(6)(10)-P(U)D(B)R70(A(B))
5.1.2.5
• • • • •
Interfaces at ODU side: 2xPDR70, 2xUDR70, 2xPBR70, 2xUBR70 or others, according to customer request Interface at antenna side: PDR70, UDR70, PBR70, UBR70 or other, according to customer request Material of the Waveguide flanges: (A) - Aluminium or (B) Brass Content of the ordering code: ISH-59-71-2”waveguide flange at antenna side”-”coupling rate”-”waveguide flange at ODU side” Example code: ISH-59-71-2PDR70(A)-3-UDR70(B)
Integrated Single Polarized Symmetrical (3dB) or Asymmetrical (6 or 10dB) Dual Band Hybrid for Frequency Range of 7-8 GHz (7.125-8.5GHz) Part No: ISH-71-85-2P(U)D(B)R84(A(B))-3(6)(10)-P(U)D(B)R84(A(B))
5.1.2.6
28
• • • • •
Interfaces at ODU side: 2xPDR84, 2xUDR84, 2xPBR84, 2xUBR84 or other, according to customer request Interface at antenna side: PDR84, UDR84, PBR84, UBR84 or other, according to customer request Material of the Waveguide flanges: (A) - Aluminium or (B) Brass Content of the ordering code: ISH-71-85-2”waveguide flange at antenna side”-”coupling rate”-”waveguide flange at ODU side” Example code: ISH-71-85-2PBR84(A)-10-UDR84(B)
C. RF ACCESSORIES 5. HYBRID COMBINERS 5.1 HYBRIDS FOR 2 ODUs 5.1.3 ISH 7/8 GHz Hybrids for 2 ODUs with NEC flange
Integrated & direct mounted Single Polarized Symmetrical (3dB) or Asymmetrical (6 or 10dB) Single Band Hybrid for Frequency Range of 7 GHz (7.125-7.750GHz) Part No: .: ISH-71-2NC2-3(6)(10)
5.1.3.1
• • •
Interfaces at ODU and antenna side: NEC flange Content of the ordering code: ISH-”frequency band”-2NC2-”coupling rate” Example code: ISH-71-2NC2-6
Integrated Single Polarized Symmetrical (3dB) or Asymmetrical (6 or 10dB) Single Band Hybrid for Frequency Range of 8 GHz (7.750-8.5GHz) Part No: ISH-77-2NC2-3(6)(10)
5.1.3.2
• • •
Interfaces at ODU and antenna side: NEC flange Content of the ordering code: ISH-”frequency band”-2NC2-”coupling rate” Example code: ISH-77-2NC2-3
Integrated Single Polarized Symmetrical (3dB) or Asymmetrical (6 or 10dB) Dual Band Hybrid for Frequency Range of 7-8 GHz (7.125-8.5GHz) Part No: .: ISH-71-85-2NC2-3(6)(10)
5.1.3.3
• • •
Interfaces at ODU and antenna side: NEC flange Content of the ordering code: ISH-”frequency band”-2NC2-”coupling rate” Example code: ISH-71-85-2NC2-6
29
C. RF ACCESSORIES 5. HYBRID COMBINERS 5.1 HYBRIDS FOR 2 ODUs 5.1.4 – 5.1.5 ISH 11-38 GHz Single and Dual Band Hybrids for 2 ODUs
Integrated Single Polarized Symmetrical (3dB) or Asymmetrical (6 or 10dB) Single Band Hybrid for Frequency Range of 11, 13, 15, 18, 23, 26, 28, 32, 38 GHz Part No: .: ISH-110…380-2NEC-3(6)(10)
5.1.4.1
• • •
Interfaces at ODU and antenna side: NEC flange Content of the ordering code: ISH-”frequency band”-2NEC-”coupling rate” Example code: ISH-110-2NEC-3
Integrated Single Polarized Symmetrical (3dB) or Asymmetrical (6 or 10dB) Dual Band Hybrid for Frequency Range of 13-15 GHz (12.75-15.35GHz) Part No: ISH-130-150-2NEC-3(6)(10)
5.1.5.1
• • •
Interfaces at ODU and antenna side: NEC flange Content of the ordering code: ISH-130-150-2NEC-”coupling rate” Example code: ISH-130-150-2NEC-3
Integrated Single Polarized Symmetrical (3dB) or Asymmetrical (6dB) Dual Band Hybrid for Frequency Range of 18-23 GHz (17.7-23.6GHz) Part No: .: ISH-180-230-2NEC-3(6)
5.1.5.2
30
• • •
Interfaces at ODU and antenna side: NEC flange Content of the ordering code: ISH-180-230-2NEC-”coupling rate” Example code: ISH-180-230-2NEC-3
C. RF ACCESSORIES 5. HYBRID COMBINERS 5.1 HYBRIDS FOR 2 ODUs 5.1.6 - 5.1.7 SSH 11-38 GHz Single and Dual Band Hybrids for 2 ODUs
Separated Single Polarized Symmetrical (3dB) or Asymmetrical (6 or 10dB) Single Band Hybrid for Frequency Range of 11, 13, 15, 18, 23, 26, 28, 32 and 38GHz Part No: SSH-110...380-2NEC-3(6)(10)-P(U)D(B)R100…320-A(B)
5.1.6.1
Interface at ODU side: 2xNEC flange, Interface at antenna side: • 11GHz: PDR100, UDR100, PBR100 or UBR100 or other, according to customer request • 11 and 13GHz: PDR120, UDR120, PBR120 or UBR120 or other, according to customer request • 13 and 15GHz: PDR140, UDR140, PBR140 or UBR140 or other, according to customer request • 18, 23 and 26GHz: PBR220 or UBR220 or other, according to customer request • 26GHz: PBR260 or UBR260 or other, according to customer request • 28, 32 and 38GHz: PBR320 or UBR320 or other, according to customer request • Content of the ordering code: SSH-”frequency band”-2NEC-”coupling rate”- “WG flange type”-”material of the WG flange: Aluminium (A), or Brass (B)”; Example code: SSH-110-2NEC-3-PDR100-A Separated Single Polarized Symmetrical (3dB) or Asymmetrical (6 or 10dB) Dual Band Hybrid for Frequency Range of 13-15GHz (12.75-15.35GHz) Part No: SSH-130-150-2NEC-3(6)(10)-P(U)D(B)R140-A(B)
5.1.7.1
• • • •
Interface at ODU side: 2xNEC flange Interface at antenna side: PDR140, UDR140, PBR140 or UBR140 or other, according to customer request Content of the ordering code: SSH-130-150-2NEC-”coupling rate”- “WG flange type”-”material of the WG flange: Aluminium (A), or Brass (B)” Example code: SSH-130-150-2NEC-3-PDR140-A
Separated Single Polarized Symmetrical (3dB) or Asymmetrical (6dB) Dual Band Hybrid for Frequency Range of 18-23GHz (17.7-23.6GHz) Part No: SSH-180-230-2NEC-3(6) P(U)D(B)R220-A(B)
5.1.7.2
• • • •
Interface at ODU side: 2xNEC flange Interface at antenna side: PBR220 or UBR220 or other, according to customer request Content of the ordering code: SSH-180-230-2NEC-”coupling rate”- “WG flange type”-”material of the WG flange: Aluminium (A), or Brass (B)” Example code: SSH-180-230-2NEC-3-PBR220-A
31
C. RF ACCESSORIES 5. HYBRID COMBINERS Electrical Specification Operating Frequency Band
Operating Frequency Range
Insertion Loss (Main)
Insertion Loss (Standby)
Inter-Port Isolation
Return Loss
6L GHz
5.925–6.425 GHz
3.5 dB
3.5 dB
20 dB
–20.8 dB
6U GHz
6.425–7.125 GHz
3.5 dB
3.5 dB
20 dB
–20.8 dB
7 GHz
7.125–7.750 GHz
3.5 dB
3.5 dB
20 dB
–20.8 dB
8 GHz
7.750–8.500 GHz
3.5 dB
3.5 dB
20 dB
–20.8 dB
10 GHz
10.100–10.700 GHz
3.5 dB
3.5 dB
20 dB
–20.8 dB
11 GHz
10.700–11.700 GHz
3.5 dB
3.5 dB
20 dB
–20.8 dB
13 GHz
12.750–13.250 GHz
3.5 dB
3.5 dB
20 dB
–20.8 dB
15 GHz
14.200–15.350 GHz
3.5 dB
3.5 dB
20 dB
–20.8 dB
18 GHz
17.700–19.700 GHz
3.5 dB
3.5 dB
20 dB
–20.8 dB
23 GHz
21.200–23.600 GHz
3.5 dB
3.5 dB
20 dB
–20.8 dB
26 GHz
24.500–26.500 GHz
3.8 dB
3.8 dB
20 dB
–19.1 dB
28 GHz
27.500–29.500 GHz
3.8 dB
3.8 dB
20 dB
–19.1 dB
32 GHz
31.000–33.400 GHz
3.8 dB
3.8 dB
20 dB
–19.1 dB
38 GHz
37.000–39.500 GHz
3.8 dB
3.8 dB
20 dB
–19.1 dB
6L–6U GHz
5.925–7.125 GHz
4.0 dB
4.0 dB
20 dB
–17.7 dB
7–8 GHz
7.125–8.500 GHz
4.0 dB
4.0 dB
20 dB
–17.7 dB
10–11 GHz
10.100–11.700 GHz
4.0 dB
4.0 dB
20 dB
–17.7 dB
13–15 GHz
12.750–15.350 GHz
4.0 dB
4.0 dB
20 dB
–17.7 dB
18–23 GHz
17.700–23.600 GHz
4.2 dB
4.2 dB
20 dB
–16.5 dB
Interface (Antenna Side):
Upon Customer's Request
Interface (ODU Side):
Upon Customer's Request
1 2
Mechanical Specification Net Weight3
3.4 kg
Material
Aluminium
Remarks: 1) Direct and separate mounting is available upon request. 2) N-connector, standard waveguide flanges or any ODU interface is available upon request. 3) Approximate value (net weight depends on the required interfaces).
32
C. RF ACCESSORIES 5. HYBRID COMBINERS Electrical Specification Operating Frequency Band
Operating Frequency Range
Insertion Loss (Main)
Insertion Loss (Standby)
Inter-Port Isolation
Return Loss
6L GHz
5.925–6.425 GHz
1.7 dB
7.0 dB
20 dB
–20.8 dB
6U GHz
6.425–7.125 GHz
1.7 dB
7.0 dB
20 dB
–20.8 dB
7 GHz
7.125–7.750 GHz
1.7 dB
7.0 dB
20 dB
–20.8 dB
8 GHz
7.750–8.500 GHz
1.7 dB
7.0 dB
20 dB
–20.8 dB
10 GHz
10.100–10.700 GHz
1.7 dB
7.0 dB
20 dB
–20.8 dB
11 GHz
10.700–11.700 GHz
1.7 dB
7.0 dB
20 dB
–20.8 dB
13 GHz
12.750–13.250 GHz
1.7 dB
7.0 dB
20 dB
–20.8 dB
15 GHz
14.200–15.350 GHz
1.7 dB
7.0 dB
20 dB
–20.8 dB
18 GHz
17.700–19.700 GHz
1.7 dB
7.0 dB
20 dB
–20.8 dB
23 GHz
21.200–23.600 GHz
1.7 dB
7.0 dB
20 dB
–20.8 dB
26 GHz
24.500–26.500 GHz
1.8 dB
7.2 dB
20 dB
–19.1 dB
28 GHz
27.500–29.500 GHz
1.8 dB
7.2 dB
20 dB
–19.1 dB
32 GHz
31.000–33.400 GHz
1.8 dB
7.2 dB
20 dB
–19.1 dB
38 GHz
37.000–39.500 GHz
1.8 dB
7.2 dB
20 dB
–19.1 dB
6L–6U GHz
5.925–7.125 GHz
2.0 dB
7.4 dB
20 dB
–17.7 dB
7–8 GHz
7.125–8.500 GHz
2.0 dB
7.4 dB
20 dB
–17.7 dB
10–11 GHz
10.100–11.700 GHz
2.0 dB
7.4 dB
20 dB
–17.7 dB
13–15 GHz
12.750–15.350 GHz
2.0 dB
7.4 dB
20 dB
–17.7 dB
18–23 GHz
17.700–23.600 GHz
2.0 dB
7.4 dB
20 dB
–16.5 dB
Interface (Antenna Side):
Upon Customer's Request
Interface (ODU Side):
Upon Customer's Request
1 2
Mechanical Specification Net Weight3
3.4 kg
Material
Aluminium
Remarks: 1) Direct and separate mounting is available upon request. 2) N-connector, standard waveguide flanges or any ODU interface is available upon request. 3) Approximate value (net weight depends on the required interfaces).
33
C. RF ACCESSORIES 5. HYBRID COMBINERS Electrical Specification Operating Frequency Band
Operating Frequency Range
Insertion Loss (Main)
Insertion Loss (Standby)
Inter-Port Isolation
Return Loss
6L GHz
5.925–6.425 GHz
1.0 dB
10.8 dB
20 dB
–20.8 dB
6U GHz
6.425–7.125 GHz
1.0 dB
10.8 dB
20 dB
–20.8 dB
7 GHz
7.125–7.750 GHz
1.0 dB
10.8 dB
20 dB
–20.8 dB
8 GHz
7.750–8.500 GHz
1.0 dB
10.8 dB
20 dB
–20.8 dB
10 GHz
10.100–10.700 GHz
1.0 dB
10.8 dB
20 dB
–20.8 dB
11 GHz
10.700–11.700 GHz
1.0 dB
10.8 dB
20 dB
–20.8 dB
13 GHz
12.750–13.250 GHz
1.0 dB
10.8 dB
20 dB
–20.8 dB
15 GHz
14.200–15.350 GHz
1.0 dB
10.8 dB
20 dB
–20.8 dB
18 GHz
17.700–19.700 GHz
1.0 dB
10.8 dB
20 dB
–20.8 dB
23 GHz
21.200–23.600 GHz
1.0 dB
10.8 dB
20 dB
–20.8 dB
26 GHz
24.500–26.500 GHz
1.1 dB
11.0 dB
20 dB
–19.1 dB
28 GHz
27.500–29.500 GHz
1.1 dB
11.0 dB
20 dB
–19.1 dB
32 GHz
31.000–33.400 GHz
1.1 dB
11.0 dB
20 dB
–19.1 dB
38 GHz
37.000–39.500 GHz
1.1 dB
11.0 dB
20 dB
–19.1 dB
6L–6U GHz
5.925–7.125 GHz
1.4 dB
11.2 dB
20 dB
–17.7 dB
7–8 GHz
7.125–8.500 GHz
1.4 dB
11.2 dB
20 dB
–17.7 dB
10–11 GHz
10.100–11.700 GHz
1.4 dB
11.2 dB
20 dB
–17.7 dB
13–15 GHz
12.750–15.350 GHz
1.4 dB
11.2 dB
20 dB
–17.7 dB
Interface1 (Antenna Side):
Upon Customer's Request
Interface2 (ODU Side):
Upon Customer's Request
Mechanical Specification Net Weight3
3.4 kg
Material
Aluminium
Remarks: 1) Direct and separate mounting is available upon request. 2) N-connector, standard waveguide flanges or any ODU interface is available upon request. 3) Approximate value (net weight depends on the required interfaces).
34
C. RF ACCESSORIES 5. HYBRID COMBINERS 5.2 Hybrids for 4 ODUs 5.2.1 Single Polarized Hybrids for 4 ODUs
Integrated Single Polarized Symmetrical (6dB) Single Band Hybrid for 4 ODUs for Frequency Range of 11, 13, 15, 18, 23, 26, 28, 32, 38 GHz Part No: ISH-110…380-4NEC-6
5.2.1.1
• • • •
Interfaces at ODU and antenna side: NEC flange Coupling rate: 6dB (25%), any other coupling rate is available upon customer request Content of the ordering code: ISH-”frequency band”-4NEC-6 Example code: ISH-130-4NEC-6
Note: this product is to be ordered with Grante antenna due to requirement of reinforced mount.
Separated Single Polarized Symmetrical (6dB) Single Band Hybrid for 4 ODUs for Frequency Range of 11, 13, 15, 18, 23, 26, 28, 32, 38 GHz Part No: SSH-110…380-4NEC-6-P(U)D(B)R120…320-A(B)
5.2.1.2
Interfaces at ODU side: 4xNEC flange, Interface at antenna side: • 13GHz: PDR120, UDR120, PBR120 or UBR120 or other, according to customer request • 13 and 15GHz: PDR140, UDR140, PBR140 or UBR140 or other, according to customer request • 18, 23 and 26GHz: PBR220 or UBR220 or other, according to customer request • 26GHz: PBR260 or UBR260 or other, according to customer request • 28, 32 and 38GHz: PBR320 or UBR320 or other, according to customer request • Material of the waveguide flange: Aluminium(A) or Brass(B) • Coupling rate: 6dB (25%), any other coupling rate is available upon customer request • Content of the ordering code: SSH-”frequency band”-4NEC-6-”WG flange type”-”material of the WG flange” • Example code: SSH-110-4NEC-6-PDR140-B
35
C. RF ACCESSORIES 5. HYBRID COMBINERS Electrical Specification Operating Frequency Band
Operating Frequency Range
Insertion Loss1 (Any Port)
Inter-Port Isolation
Return Loss
11 GHz
10.700–11.700 GHz
7.4 dB
20 dB
–16.5 dB
13 GHz
12.750–13.250 GHz
7.4 dB
20 dB
–16.5 dB
15 GHz
14.200–15.350 GHz
7.4 dB
20 dB
–16.5 dB
18 GHz
17.700–19.700 GHz
7.4 dB
20 dB
–16.5 dB
23 GHz
21.200–23.600 GHz
7.4 dB
20 dB
–16.5 dB
26 GHz
24.500–26.500 GHz
8.0 dB
20 dB
–16.5 dB
28 GHz
27.500–29.500 GHz
8.0 dB
20 dB
–16.5 dB
32 GHz
31.000–33.400 GHz
8.0 dB
20 dB
–16.5 dB
38 GHz
37.000–39.500 GHz
8.0 dB
20 dB
–16.5 dB
Interface2 (Antenna Side):
Upon Customer’s Request
Interface3 (ODU Side):
Upon Customer’s Request
Mechanical Specification Net Weight4
7.0 kg
Material
Aluminium
Remarks: 1) Different coupling coefficients are available upon request. 2) Direct and separate mounting is available upon request. 3) N-connector, standard waveguide flanges or any ODU interface is available upon request. 4) Approximate value (net weight depends on the required interfaces).
36
C. RF ACCESSORIES 5. HYBRID COMBINERS 5.2 Hybrids for 4 ODUs 5.2.2 Dual Polarized Hybrids for 4 ODUs
Integrated Dual Polarized Symmetrical (3dB) or Asymmetrical (6 or 10dB) Single Band Hybrid for Frequency Range of 11, 13,18, 38 GHz Part No: IDH-110/130/180/380-4NEC-V3(6)(10)-H3(6)(10)-(G)(R) • • • •
5.2.2.1
•
Interfaces at ODU side: NEC flange Interfaces at antenna side: interface for dual polarized Grante(G) or RFS(R) Coupling rate: 3, 6 or 10dB at Vertical and Horizontal polarization Content of the ordering code: IDH-”frequency band”-4NEC-”coupling rate for vertical pol. “-”coupling rate for horizontal pol.””Antenna manufacturer” Example code: IDH-130-4NEC-V6-H3-G
Note: this product is to be ordered with Grante antenna due to requirement of reinforced mount. Electrical Specification Operating Frequency Band
Operating Frequency Range
Insertion Loss1 (Main)
Insertion Loss1 (Standby)
Inter-Port Isolation (Identical Polarization)
Inter-Port Isolation (Cross Polarization)
Return Loss
11 GHz
10.700–11.700 GHz
4.5 dB
4.5 dB
20 dB
40 dB
–16.5 dB
11 GHz
10.700–11.700 GHz
2.7 dB
8.0 dB
20 dB
40 dB
–16.5 dB
11 GHz
10.700–11.700 GHz
2.0 dB
11.8 dB
20 dB
40 dB
–16.5 dB
13 GHz
12.750–13.250 GHz
4.5 dB
4.5 dB
20 dB
40 dB
–16.5 dB
13 GHz
12.750–13.250 GHz
2.7 dB
8.0 dB
20 dB
40 dB
–16.5 dB
13 GHz
12.750–13.250 GHz
2.0 dB
11.8 dB
20 dB
40 dB
–16.5 dB
18 GHz
17.700–19.700 GHz
4.5 dB
4.5 dB
20 dB
40 dB
–16.5 dB
18 GHz
17.700–19.700 GHz
2.7 dB
8.0 dB
20 dB
40 dB
–16.5 dB
18 GHz
17.700–19.700 GHz
2.0 dB
11.8 dB
20 dB
40 dB
–16.5 dB
38 GHz
37.000–39.500 GHz
5.2 dB
5.2 dB
20 dB
36 dB
–16.5 dB
38 GHz
37.000–39.500 GHz
3.2 dB
8.6 dB
20 dB
36 dB
–16.5 dB
38 GHz
37.000–39.500 GHz
2.5 dB
12.4 dB
20 dB
36 dB
–16.5 dB
Interface (Antenna Side):
Upon Customer’s Request
Interface (ODU Side):
Upon Customer’s Request
2 3
Mechanical Specification Net Weight4
7.0 kg
Material
Aluminium
Remarks: 1) Different coupling coefficients are available upon request. 2) Direct and separate mounting is available upon request. 3) N-connector, standard waveguide flanges or any ODU interface is available upon request. 4) Approximate value (net weight depends on the required interfaces). 37
C. RF ACCESSORIES 6. MOUNTING BRACKETS
Mounting bracket (Separate Interface) for NEC ODU (Pasolink V4, NEO) without interface adapter for the frequency range of 6/7/8 GHz Part No: OMT-110…380-2NEC-(G)(R)
6.1
•
Applicable for all ODUs with N-connector or standard waveguide flange
Mounting brackets (Separate Interface) for NEC ODU with interface adapter for the frequency range of 7-8, 11, 13-15, 18-23, 26, 28, 32-38GHz Part No: SI-110…380-NEC-P(U)D(B)R100…320-A(B)
6.2
38
Interface at ODU side: NEC flange; Interface at antenna side: • 7 and 8 GHz: PDR84, UDR84, PBR84 or UBR84 or other, according to customer request • 11GHz:PDR100, UDR100, PBR100 or UBR100 or other, according to customer request • 11 and 13GHz: PDR120, UDR120, PBR120 or UBR120 or other, according to customer request • 13 and 15GHz: PDR140, UDR140, PBR140 or UBR140 or other, according to customer request • 18, 23 and 26GHz: PBR220 or UBR220 or other, according to customer request • 26GHz: PBR260 or UBR260 or other, according to customer request • 28, 32 and 38GHz: PBR320 or UBR320 or other, according to customer request • Material of the waveguide flange: Aluminium(A) or Brass(B) • Content of the ordering code: SI-”frequency band”-NEC-”WG flange type”-”material of the WG flange” • Example code: SI-110-NEC-PDR120-B, SI-130-150-NEC-PDR140-A
C. RF ACCESSORIES 7. Waveguide Transducer
Waveguide transducer Part No: WGA -59...380-P(U)D(B)R70…320-A(B)-N(SMA)(K) •
7.
•
• • •
Waveguide type: • 6L and 6U GHz: PDR70, UDR70, PBR70 or UBR70 or other, according to customer request • 7 and 8GHz: PDR84, UDR84, PBR84 or UBR84 or other, according to customer request • 10 and 11GHz: PDR100, UDR100, PBR100 or UBR100 or other, according to customer request • 11 and 13GHz: PDR120, UDR120, PBR120 or UBR120 or other, according to customer request • 13 and 15GHz: PDR140, UDR140, PBR140 or UBR140 or other, according to customer request • 18, 23 and 26GHz: PBR220 or UBR220 or other, according to customer request • 26GHz: PBR260 or UBR260 or other, according to customer request • 28, 32 and 38GHz: PBR320 or UBR320 or other, according to customer request Coaxial connector type: • 6L, 6U, 7 and 8 GHz: N (Female) or other, according to customer request • 10, 11, 13, 15, 18 and 23 GHz: SMA (Female) or other, according to customer request • 26, 28, 32 and 38 GHz: K (Female) or other, according to customer request Material of the waveguide flange: Aluminium(A) or Brass(B) Content of the ordering code: WGA “Frequency range”-”Waveguide type”-”Material of the WG flange”-“Coaxial connector type” Example codes: WGA 5971-UDR70-B-N or WGA 180230-PDR220-B-SMA or WGA 380-UBR320-A-K
Electrical Specification Waveguide
Operating Frequency Band
Operating Frequency Range
Insertion Loss
Return Loss
Coaxial Connector Type1
Waveguide Flange Type2
R70
6L–6U GHz
5.925–7.125 GHz
0.4 dB
–20 dB
N
PDR/UDR
R84
7–8 GHz
7.125–8.500 GHz
0.4 dB
–20 dB
N
PDR/UDR/PBR/UBR
R100
10–11 GHz
10.100–11.700 GHz
0.4 dB
–20 dB
SMA
PDR/UDR/PBR/UBR
R120
13 GHz
12.750–13.250 GHz
0.4 dB
–20 dB
SMA
PDR/UDR/PBR/UBR
R140
13–15 GHz
12.750–15.350 GHz
0.4 dB
–20 dB
SMA
PDR/UDR/PBR/UBR
R220
18–23 GHz
17.700–23.600 GHz
0.4 dB
–20 dB
SMA
PBR/UBR
R260
26 GHz
24.500–26.500 GHz
0.4 dB
–18 dB
K
PBR/UBR
R260
28 GHz
27.500–29.500 GHz
0.4 dB
–18 dB
K
PBR/UBR
R320
28 GHz
27.500–29.500 GHz
0.4 dB
–15 dB
K
PBR/UBR
R320
32 GHz
31.000–33.400 GHz
0.4 dB
–15 dB
K
PBR/UBR
R320
38 GHz
37.000–39.500 GHz
0.4 dB
–15 dB
K
PBR/UBR
R120 to R320:
0.1 kg
Mechanical Specification Net Weight3
R70 / R84 / R100:
Material
Aluminium or Brass
0.2 kg
Remarks: 1) Other connector types are available upon request. 2) Other flange types are available upon request (e.g. American Standard CPR/UG). 3) Approximate value (net weight depends on the required connector, flange, and material). 39
C. RF ACCESSORIES 8. Low Loss Cables
Low Loss Cables for frequency range 6-8GHz Part No: .: LCC-50-NR(S)MNR(S)M-1.0(1.2)
8.1 8.6
40
• • • • • • •
Connector type: Male N connector Impedance: 50 Ohm Connector pattern: Straight or Right Angle Cable lenght: 1.0 meter or 1.2 meter Content of the ordering code: LCC-50-“connector type left end””connector type right end”-“length” Example code: LCC-50-NS(M)NS(M)-1.0 Other lengths are available upon customer request.
D. Measuring tools & accessories 9. Measuring tools
Interconnection radiofrequency cable set for 2 ODUs
9.1
Interconnection cable set for two ODUs, Frequency Range of 6, 7, 8, 11, 13, 15, 18, 23, 26, 38 GHz (In case of 6/7/8GHz the ODU has N connector), comprising of: Attenuators - 20 dB with N(SMA)(K)* connectors - 2pcs • Waveguide adapter rings - 2pcs • Waveguide-SMA(K)* converters - 2 pcs, in case of 11-38GHz • N(SMA)(K) – N(SMA)(K)* cable - 1pc • IDU - ODU IF cables with connectors - 2pcs • Screws - 12pcs, in case of 11-38GHz • Content of the ordering code: NEC-ICBSET-”frequency range”-LAB-Bundle • Example code: NEC-ICBSET-38G-LAB-Bundle * N connector is used for 6/7/8GHz (if the ODU has N connector), SMA for 11-26GHz, K for 28-38GHz Direct mounted measuring frame (11-38GHz), narrowband / wideband
9.2
Part No: MS3100
Direct mounted measuring frame for frequency range of 11, 13, 15, 18, 23, 26, 38 GHz, developed for simulation of point to point microwave links • The system can be used for the simulation of hot standby systems (1+1) too. In this case two direct mounted type hybrids should be installed to the place of the ODUs. • For adjusting the attenuation of the microwave path the curves of the Variable Attenuator can be used (between 40 and 100dB). • To check the frequencies of the ODUs there are two pieces SMA (10-23GHz) or K (26-38GHz) connectors, which should be terminated if they are not used. • Main parts of the system: • Variable Attenuator (attenuation*: 0...30 dB) - 2pcs • Fixed Attenuator (attenuation*: 20 dB) - 2pcs • (Single polarized Hybrid (3dB) (SH…-2NEC-3) - 2pcs – not included in this product) • SMA (10–23 GHz) or K (26–40 GHz) connector - 2pcs • Radio Interfaces for NEC ODU - 4pcs • Low Power Termination (SMA male / K male) - 2pcs • Example code: MS3100 130150 * Other attenuation values are available upon request Measuring frame for XPIC system for 11 to 38GHz
9.3
Part No: NEC-ICBSET-59…380-LAB-Bundle
Part No:MS3200
Measurement frame for XPIC system is developed to test NEC PASOLINK XPIC System. • Frequency range: 11/13/15/18/23/26/28/32/38GHz • Type of system: Dual polarized Measurement System • Total Attenuation: between 40 and 100 dB • Number of interface for NEC ODUs: 4 • Type of connectors: SMA (female) or K (female) To check the frequencies of the ODUs there are four pieces SMA (10-23GHz) or K (26-40GHz) connectors, which should be terminated if they are not used.
41
D. Measuring tools & accessories 9. Accessories (adapters) for laboratory usage
Adapter ring to mount Waveguide Transducer on NEC ODU • •
Part No: NEC-7…38-LAB-AM
Frequency range: 7-38GHz Example code: NEC-18-LAB-AM
9.4.1
Waveguide transition • •
9.4.2
42
• •
Waveguide type: PBR70, PBR84 , PBR120, PBR140, PBR220, PBR260 or other, according to customer request Material of the Waveguide flange is (A) - Aluminium or (B) Brass. Frequency range: 7/8G / 13G / 26G Example code: WGTR 130-PBR120(A)-PBR140(A)-I + 2 Cu/Al)
Part No: WGTR 71…260-PBR…-PBR… + 2 Cu/Al
E. ANTENNA 10. ANTENNA
High Performance Dielectric Antenna (HPA)
10.1
HPA Family offers high interference protection, excellent radiation characteristics and outstanding front-to-back ratio. • Frequency range: 4-38GHz • Frequency band: single / dual • Diameters: 0.17 – 3.0m • Mounting mode with ODUs: Separate / Integrated • Polarization: Single (S) / Dual (D)
High Cross Polarization Discrimination Antenna (HXPA)
10.2
Part No:HPA 0.17…1.8 D … SR / FR
High performance dual polarized antennas with integrated Orthomode Transducer. • Antenna Family: High performance (HPA) or High cross-polar discrimination (HXPA) • Frequency range: 10-38GHz • Frequency band: single • Diameters: 0.6 (0.17*) – 1.8m (*in case of HPA Family) • Mounting mode with ODUs: Integrated (OMT + Interface included) • Polarization: Dual (D)
Antenna with Heating System
10.4
Part No: HXPA 0.8…1.8 D … FR
HXPA Family offers extremely high interference protection, superior radiation pattern, excellent cross-polarization discrimination, and outstanding inter-port isolation, giving the non-compromise solution even under the toughest conditions. • Frequency range: 4-38GHz • Frequency range: 4-8GHz • Frequency band: single • Diameters: 0.8 – 1.8m • Mounting mode with ODUs: Separate / Integrated • Polarization: Dual
Dual Polar Direct Mounted Antenna with OMT included
10.3
Part No: HPA 0.17…1.8 S … SR / FR
Part No:---(EHI)-
High performance antennas with integrated electronic radome heating system • Antenna Family: High performance (HPA) or High cross-polar discrimination (HXPA) • Diameter: 0.3 – 1.8m • Polarization: Single (S) / Dual (D) • Frequency band: 4 – 38 GHz • Radome: Solid for 0.3 m (SR), flexible from 0.4 m (FR) • ODU Interface: NEC or standard waveguide • Content of the ordering code: ---(EHI)- • Example code: HPA-1.2-D-130-FR(EHI)-2NEC 43
E. ANTENNA 10. ANTENNA
Small size antenna
10.5
44
Small size parabolic antennas for special applications. • ODU Interface: NEC or standard waveguide • Content of the ordering code: ---- • Example code: HPA-0.17-S-380-CR-PBR320(A)
Part No: HPA-[0.17|0.22]-S-180...380-CR-
General Terms and Conditions 1. Production Leadtime General Production Leadtime: within 4 weeks without forecast or 2 weeks on forecast basis. New Product Development and Production Leadtime: within 8-10 weeks. 2. General Delivery Term EXW Budapest However, we are ready to arrange CIP Airport or (within EU) door - to - door delivery of our products upon request. 3. Manufacturing capacity • I/O board: 35 000 – 40 000 pcs / month • Cable for I/O board and other indoor cables*: 4 000 – 4 500 pcs / month • RF accessories: 200 – 300 pcs / type / month *capacity can be increased up to 7 500 pcs / month 4. Packing & labelling Standard packing is exportworthy carton boxes with the necessary filling material. Standard label includes soldto-party and consignee, PO no. & date, delivery address, item code & quantity, case no. Custom label is available upon request. 5. Warranty Warranty period is 24 (twenty-four) month from the delivery date. NEE warrants that products are free from any faults and defects caused by workmanship, manufacturing process and/or the material procured by the supplier, and shall at all times conform to the specification and be fit for the purpose. 6. Discontinue notice and Compliance to Standards • Discontinue Notice for existing products or component parts will be announced to Customer / NEC Affiliates six (6) month before the discontinuance of those products. • All products and packing materials are in compliance with REACH and RoHs Directives and applicable EU law. • NEE and its suppliers have ISO 9001 / 14001 Certification. 7. Product development & samples • Our product portfolio is subject to continuous development and expansion – there is also possibility for customization according to specific individual requirements. We are looking forward to any questions / comments / requests. • In order to help introducing our products to your customers, we are willing to send you product samples, according to your requirements. Please let us know your preference - the contact points are given on the back cover of the catalogue.
45
Contact information
Company name: Address: E-mail: Web: Phone: Fax:
NEC Eastern Europe Ltd. 1142 Budapest, Ungvár u. 64-66., Hungary
[email protected] www.nec.hu +36-1-814-6424 +36-1-321-8202
©NEC Corporation. All rights reserved. NEC Logo and products are trademarks or registered trademarks of NEC Corporation or its subsidiaries and affiliates in Japan and/or other countries. Products are subject to availability. The information contained herein is subject to change without notice. The only warranties for NEC products are set forth in the express warranty statements accompanying such products and services. NEC shall not be liable for technical or editorial errors or omissions contained herein. 46
Catalogue no. NEE_20111006 Issued in October 2011
