Module 07 Part 4.docx

April 22, 2018 | Author: Aviation World | Category: Rivet, Electrical Connector, Electrical Wiring, Cable, Wire
Share Embed Donate


Short Description

Module 07 Part 4.docx...

Description

www.easaquestionpapers.blogspot.com

06. Fits and Clearances.

Question Number. 1. Tolerances ar are cl classified in two ways, these are. Option A. Dimensional an and is isometric. Option B. Upper and lower. Option . Dimensional an and !eometric. orre orrecct Ans Answe werr is. is. Dimen imensi sion onal al and and !eo !eom metri etric. c. "#pla "#plana natio tion. n. AA$ AA$% % & lea leafle flett '(1 '(1 p1) p1) para para *.1 *.11 1.

Question Number. '. The ma#imu imum permissible bow in a steel tube is. Option A. 1 + --. Option B. 1 + '--. Option . 1 + )--. orrect Answer is. 1 + )--. "#pl "#plan anat atio ion. n. AA$ AA$% % & ea eafl flet et )(. )(.

Questio tion Nu Number. /. The e0 e0uipme pment re re0uired to to ca carry out a run(out ch chec on on a shaft wo would  be. Option A. a DT$ and 232 blocs. Option B. a ball bearin! in! and a micr icrome ometer. Opti Option on . a surf surfac acee plate late and and a thre threee le! le! tram tramm mel. el. orrect Answer is is. a DT DT$ an and 23 232 blo bloccs. "#pl "#plan anat atio ion. n. A/ A/.1 .1/( /(1B 1B %a!e %a!e ('('-..

Question Number. . 4hat is the ma#imum bow allowed in a strut5. Option A. 1 in '--. Option B. 1 in *--. Option . 1 in )--. orrect Answer is. 1 in )--. "#pl "#plan anat atio ion. n. AA$ AA$% % & ea eafl flet et '(1'(1-..

Questio tion Nu Number. *. 4hich of of th the fo follow lowin! in! sh shafts wo would you you use to to ob obtain a cl clearance fi fit in a bush -.6*- inch diameter5. Option A. -.6*' inch. Option B. -.67 inch. Option . 6*- inch. orrect An Answer is is. -.67 in inch. "#planation. N$.

Questio tion Number. ). !au!e5. Option A. learance. Option B. Tolerance. Option . Allowance.

4hich of the follow lowin! in! is checed when usin! in! a 28O 9 NO (8O2

Share your documents with us at ([email protected] ( [email protected])) DownloadOur Mobile pp !or "ecent #apers

www.easaquestionpapers.blogspot.com orrect Answer is. "#planation. N$.

Tolerance.

Question Nu Number. 6. 4hich of of th the fo followin! is is a 2Bilateral To Tolerance25. Option A. ' inches (-.--'. Option B. ' inches :-.--'. Option . ' inches ;-.--'. orrect An Answer is is. ' in inches ;;-.--'. "#planation. N$.

Question Number. 7. A tolerance is. Opti Option on A. a per perm mitte itted d dif diffe fere renc ncee bet betwe ween en new new and and worn worn dim dimensi ension ons. s. Opti Option on B. a perm permit itted ted
View more...

Comments

Copyright ©2017 KUPDF Inc.
SUPPORT KUPDF