-connect your phone to the pc and install get spc in the phone (LG CDMA SECRETS CODES Field Test MENU > 0 > 000000 > Field Test Other Programmi ng Secrets: menu + 9 and enter SPC: 000000? or may be other SPC typed by user. AKey: press STO for some time while you can see special code enter zone. Leaked) -run it and press on get spc, press ok or yes and it will display six digit numb er write this number down because we will need it. -in the dialer type ##778# click on edit and write the six digit number that you wrote down. -next a screen that says EPST and below that say Display will appear. -we well need to modify some of this ones DISPLAY -NAM NAME write you ten digit numer -SCM write the first two digit of area code of the phone number(if appears to be editable if not leave it like that) -MSID write your ten digit phone number click in view info and go to NAM SETTINGS -NAM NAME write your ten digit phone number -MOBILE DIRECTORY NUMBER write your ten digit number -MIN1 4764516 -MIN2 first three digits of your phone number (area code) -MSID write your ten digit phone number -MCC 310 -MNC 27 -NMSI 27and write your ten digit phone number -IMSI 31027and write your ten digit phone number click in view info and go to CDMA SETTINGS -A-SYS PRIMARY 283 -B-SYS-PRIMARY 384 -A SYS-SECUNDARY 691 -A SYS-SECUNDARY 777 -MON_TERM_FOR_HOME ENABLE -MON_TERM_FOR_SID ENABLE -MON_TERM_FOR_NID ENABLE -EVRC ENABLED DISABLED -HOME PAGE VOICE 13K -HOME ORIG VOICE 13K -ROAM ORIG VOICE 13K click in view info and go to HOME SID/NID -HOME SID/NID #1 6503/65535 click in view info and go to MODEM SETTINGS -SLOT CYCLE 1 -PREFERRED SERVING AUTO
-PREFERRED MODE AUTO -HDR HYBRID ENABLE -CLEAR ALL MRU NO click in view info and go to -PRL -UPDATE PRL FILE AND YOU HAVE TO TRANSER THE FILE 02001 THAT IS IN METROPCS.RAR AND SELECT THAT ONE click in view info and go to SECURITY -HDR AN AUTH USER ID
[email protected] -HDR AN AUTH PASS metropcs -PPP USER ID
[email protected] -PPP PASS metropcs click in view info and go to DATA PARAMETERS -PACKET DIAL #777 click in view info and go to M.IP SETTINGS -NUMBER OF PROFILES 6 -ACTIVE USER PROFILE 0 -MIP_MODE SIMPLE IP ONLY -MIP REGISTRATION RETRIES 1 -MIP REGISTRATION RETRY 2000 ms -MIP PRE-REGISTRATION TI 30 -MOBILE NODE-HA Disable -SEND A REGISTRATION Enable -DORMAND HANDOFF Disable click in view info and go to M.IP DEFAULT PROFILE -ENABLE PROFILE Enable -NAI
[email protected] -MN HA SPI SET Disable -MN HA SPI VALUE 0 -MN AAA SPI SET Disable -MN AAA SPI VALUE 0 -HOME ADRESS 0.0.0.0 -PRIMARY HA ADDRESS 255.255.255.255 -SECUNDARY HA ADDRESS 255.255.255.255 -HA SHARED SECRET metropcs -AAA SHARED SECRET metropcs -DMU 0 -MN 0 make sure that M.IP CUSTOMER PROFILE 1,2,3,4,5,6 are Disable click menu ok and reset. when the phone resets please install Metro WAP and Arcsoft 5_0_70_24 from METROP
CS.CAB also after everything is done please dont forget to take the phone to metropcs s o they can put you nam in the metropcs system thats what they call flash the pho ne to metropc. Internet Sharing - tethering big thanks to silvaadams from ppcgeeks make sure you have internet on your phone ofcourse start up comm manager and click your internet sharing button thingy lol click connect on the lower left hand corner wait for phone to say check usb connection then connect phone to usb and usb to computer (should say connected) open internet explorer go to settungs go to internet options go to connections tab click on lan settings click proxy server check use proxy blabla then type wap.metropcs.net port 3128 then ok open up firefox once open go to tools> options> advanced> network under network click settings select manual proxy config under http proxy type wap.metropcs.net [port:] 3128 then check off "use this proxy server for all protocols" 2.option. HTC 6850 Touch Pro change MEID change ESN Repair / Clone Solution i as sume you have a phone already in metropcs so u can clone it and avoide paying $4 0 or $50 dollars activation fee. -now MAKE SURE YOU WRITE DOWN OR BACK UP ALL YOUR DATA SETTINGS BEFORE YOU DO TH IS JUST IN CASE - download http://www.4shared.com/file/14065813.../MetroPCS.html - install WModem_Driver_Installer_v1.2.2.4_WWE -make sure to install get spc on the phone run it and get ur spc code -disconnect phone -put phone in diag mode (dial ##3424#) wait until the white screen disapear and connect your phone to ur pc -now install all the drivers but maybe it will tell that u need qcmdmxp or anoth er one so just select files from Program Files\HTC\WModem_Installer\WinXp -Disable USB connection in Active Sync by unchecking checkbox in Connection Sett ings of Active Sync -Hold Pwr and Vol Down buttons and push reset button to boot the phone in bootlo ader mode.
-Run mtty.exe from TP ESN FILES2 -Leave every setting alone apart from change the 'Port' to 'USB' in yhe drop dow n box. Hit OK. In the window that opens up, type the following commands (All Commands are case Sensitive) Hit enter after typing each one. You may see nothing while typing, ju st type carefully. 1. 12 3. 4. 5. 6.
rtask a echo_on readCID writeCID 00000000 readCID (window should return CID as 00000000) rtask c (will probably give and error - mine did!)
-Soft reset phone and close mtty. -Re-enable USB connection in connection settings of ActiveSync. Make sure phone is 'connected' to ActiveSync, you might have to unplug and plug in usb to make t his happen. -Flash phone with Raphael_CDMA_HSPL_037.exe -Let phone restart. -disconnect phone -put phone in diag mode (dial ##3424#) wait until the white screen disapear and connect your phone to ur pc -download http://rapidshare.com/files/21078960...008-09-19_.rar -open QPST configuration and click on add port -make sure to memorize the port that says htc diagnostic that port com is really important we well use it for many things -Launch DFS. from TP ESN FILES2 -Select your phone's com port. (top left ish) this is the port that i was talkin g about diagnostic port com -Select 6950 from the HTC devices menu on the left. Before you all start, yes I know we are programming a 6850, but the secret here is that the MEID portion of the 6850 equipment file in DFS ties up to the MEID locations in the radio rom su pplied (which was ported from the diamond) -Ignore any errors at the bottom of the screen about equipment not found etc... Remember, just follow the instructions!! So, once the com port is connected, go the MEID section and type your originial metropcs phone the one you have to clon e MEID(D)(decimal) it should be on the back of the phone also make sure that the original metropcs phone os turn off u dont want to turn this phone ever in your life. Ignore the pESN that it creates but do not modify it -Click Write like 4 times and it will write it to the phone no matter what it sa ys at the bottom of the screen. -Close DFS and soft reset.
-now go to http://www.previo.net/meid-esn-converter.html -type your MEID(D)(decimal) and click submit the important thing here is ESN the hex not the dec. so copy the hex one. -Go into diag mode ##3424# again wait untill the white screen disappear and conn ect it usb to ur pc -Open up the attached CDMA Workshop 2.7 cdma workshop.exe but the one is in METR OPCS.RAR not the one is in TP ESN FILES2 and select the com port to connect your phone. THIS COM PORT IS THE DIAGNOSTIC PORT. -click connect and then read -in your phone go to dialer and type ##778# edit and type your spc code then. -Go to the security tab in workshop and click read by the esn. It should display your current esn. -Type the esn that the website give you the hex one. this should be your origina l metropcs nam number -click write. -Go to Nam tap and Click in Banner -Type MetroPCS and -click write -now Close CDMA WS and soft reset -now install the radio u want to use from here http://forum.xda-developers.com/show...ighlight=radio recommend TELUS v1.04.05V or VERIZON v1.03.03V -when is done type in your dialer ##778# edit in the screen that says EPST and b elow that say Display will appear. -we well need to modify some of this ones DISPLAY -NAM NAME write you ten digit numer -SCM write the first two digit of area code of the phone number(if appears to be editable if not leave it like that) -MSID write your ten digit phone number click in view info and go to NAM SETTINGS -NAM NAME write your ten digit phone number -MOBILE DIRECTORY NUMBER write your ten digit number -MIN1 4764516 -MIN2 first three digits of your phone number (area code) -MSID write your ten digit phone number -MCC 310 -MNC 27 -NMSI 27and write your ten digit phone number -IMSI 31027and write your ten digit phone number
click in view info and go to CDMA SETTINGS -A-SYS PRIMARY 283 -B-SYS-PRIMARY 384 -A SYS-SECUNDARY 691 -A SYS-SECUNDARY 777 -MON_TERM_FOR_HOME ENABLE -MON_TERM_FOR_SID ENABLE -MON_TERM_FOR_NID ENABLE -EVRC ENABLED DISABLED -HOME PAGE VOICE 13K -HOME ORIG VOICE 13K -ROAM ORIG VOICE 13K click in view info and go to HOME SID/NID -HOME SID/NID #1 6503/65535 click in view info and go to MODEM SETTINGS -SLOT CYCLE 1 -PREFERRED SERVING AUTO -PREFERRED MODE AUTO -HDR HYBRID ENABLE -CLEAR ALL MRU NO click in view info and go to -PRL -UPDATE PRL FILE AND YOU HAVE TO TRANSER THE FILE 02001 THAT IS IN METROPCS.RAR AND SELECT THAT ONE click in view info and go to SECURITY -HDR AN AUTH USER ID
[email protected] -HDR AN AUTH PASS metropcs -PPP USER ID
[email protected] -PPP PASS metropcs click in view info and go to DATA PARAMETERS -PACKET DIAL #777 click in view info and go to M.IP SETTINGS -NUMBER OF PROFILES 6 -ACTIVE USER PROFILE 0 -MIP_MODE SIMPLE IP ONLY -MIP REGISTRATION RETRIES 1 -MIP REGISTRATION RETRY 2000 ms -MIP PRE-REGISTRATION TI 30 -MOBILE NODE-HA Disable -SEND A REGISTRATION Enable -DORMAND HANDOFF Disable
click in view info and go to M.IP DEFAULT PROFILE -ENABLE PROFILE Enable -NAI
[email protected] -MN HA SPI SET Disable -MN HA SPI VALUE 0 -MN AAA SPI SET Disable -MN AAA SPI VALUE 0 -HOME ADRESS 0.0.0.0 -PRIMARY HA ADDRESS 255.255.255.255 -SECUNDARY HA ADDRESS 255.255.255.255 -HA SHARED SECRET metropcs -AAA SHARED SECRET metropcs -DMU 0 -MN 0 make sure that M.IP CUSTOMER PROFILE 1,2,3,4,5,6 are Disable click menu ok and reset. when the phone resets please install Metro WAP and Arcsoft 5_0_70_24 from METROP CS.CAB reset it one more time finally call *228 wait untill the spanish thing is over and press 1 then wait 2 seconds press 1 again wait 2 seconds and press 1 again this will make u talk to custumer service tell them u are having trubles with ur phone and you need to re program your phone sometimes they are lazys and dont want to do it so insinst. p lease give them your MEID(D) decimal number and depend of your phone they will t ell you do this or do that but dont do it write everything down and tell them ye s ok i done hahaha in my case of kyocera melo they told me to do this type 11111 1 go to options service go to program 587846 type mdn MYPHONENUMBER type min 323 4764516 and type home sid 6503 after that they told me im done just soft reset i t and that its but when i hang up i didn do it and please dont do it go to diale r and type ##778# edit and we need to make some changes. DISPLAY -NAM NAME write the program number they give u my case 587846 -SCM write 58 click in view info and go to NAM SETTINGS -NAM NAME write the program number they give u my case 587846-MOBILE DIRECTORY N UMBER write your ten digit number -MIN1 4764516 type the min number they give in my case 3234764516 323 is the are a code but when u restar the phone this dissapear click in view info and go to HOME SID/NID -HOME SID/NID #1 6503/65535 here just change the the SID for the one they give y ou my case 6503 the other one leave it as 65535
soft reset and you are ready to go. Internet Sharing - tethering big thanks to silvaadams from ppcgeeks make sure you have internet on your phone ofcourse start up comm manager and click your internet sharing button thingy lol click connect on the lower left hand corner wait for phone to say check usb connection then connect phone to usb and usb to computer (should say connected) open internet explorer go to settungs go to internet options go to connections tab click on lan settings click proxy server check use proxy blabla then type wap.metropcs.net port 3128 then ok open up firefox once open go to tools> options> advanced> network under network click settings select manual proxy config under http proxy type wap.metropcs.net [port:] 3128 then check off "use this proxy server for all protocols"
