Manual I-24xW-S (2).pdf
February 19, 2017 | Author: Mario Junior | Category: N/A
Short Description
Download Manual I-24xW-S (2).pdf...
Description
I-240W-S, I-241W-S
31 I-240W-S and I-241W-S unit data sheet NTP 172 Install an I-240W-S or I-241W-S indoor ONT NTP 173 Replace an I-240W-S or I-241W-S indoor ONT NTP 174 Configure an I-240W-S or I-241W-S ONT
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet
31.1 I-240W-S and I-241W-S part numbers and identification 31.2 I-240W-S and I-241W-S general description
31-2
31-3
31.3 I-240W-S and I-241W-S software and installation feature support 31-3 31.4 I-240W-S and I-241W-S interfaces and interface capacity 31-4 31.5 I-240W-S and I-241W-S LEDs
31-7
31.6 I-240W-S and I-241W-S detailed specifications
31-8
31.7 I-240W-S and I-241W-S GEM ports and T-CONTs 31.8 I-240W-S and I-241W-S power support 31.9 I-240W-S and I-241W-S functional blocks
31-10
31-10 31-10
31.10 I-240W-S and I-241W-S standards compliance
31-13
31.11 I-240W-S and I-241W-S special considerations
31-13
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-1
31 I-240W-S and I-241W-S unit data sheet
31.1
I-240W-S and I-241W-S part numbers and identification Table 31-1 provides part numbers and identification information for I-240W-S and I-241W-S indoor ONTs. Table 31-1 I-240W-S and I-241W-S indoor ONT part numbers and identification
Mnemonic
Ordering kit part number
Provisioning part number
Description
CLEI
CPR
ECI/ Bar code
I-240W-S
3FE 54180 AA
3FE 54276 AA
2 POTS ports, 4 Gig-E 10/100/1000 Base-T interfaces, and 1 Wi-Fi radio on/off switch. Includes ac/dc power cord with European (EU) variant plug.
3FE 54180 BA
2 POTS ports, 4 Gig-E 10/100/1000 Base-T interfaces, and 1 Wi-Fi radio on/off switch. Includes ac/dc power cord with Australian (AU) variant plug.
3FE 54180 CA
2 POTS ports, 4 Gig-E 10/100/1000 Base-T interfaces, and 1 Wi-Fi radio on/off switch. Includes ac/dc power cord with United Kingdom (UK) variant plug.
3FE 54180 EA
2 POTS ports, 4 Gig-E 10/100/1000 Base-T interfaces, and 1 Wi-Fi radio on/off switch. Includes ac/dc power cord with United States (US) variant plug.
2 POTS ports, 4 Gig-E 10/100/1000 Base-T interfaces, 1 RF video connector, and 1 Wi-Fi radio on/off switch. Includes ac/dc power cord with European (EU) variant plug.
3FE 54492 BA
2 POTS ports, 4 Gig-E 10/100/1000 Base-T interfaces, 1 RF video connector, and 1 Wi-Fi radio on/off switch. Includes ac/dc power cord with Australian (AU) variant plug.
3FE 54492 CA
2 POTS ports, 4 Gig-E 10/100/1000 Base-T interfaces, 1 RF video connector, and 1 Wi-Fi radio on/off switch. Includes ac/dc power cord with United Kingdom (UK) variant plug.
3FE 54492 EA
2 POTS ports, 4 Gig-E 10/100/1000 Base-T interfaces, 1 RF video connector, and 1 Wi-Fi radio on/off switch. Includes ac/dc power cord with United States (US) variant plug.
I-241W-S
31-2
3FE 54492 AA
3FE 54276 AB
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet
31.2
I-240W-S and I-241W-S general description I-240W-S and I-241W-S indoor ONTs provide the subscriber interface for the network by terminating the PON interface and converting it to user interfaces that directly connect to subscriber devices. The ONT is compatible with all existing subscriber equipment, including analog phones with both tone and rotary dial capabilities, cordless phones, modems, fax machines, and caller ID boxes (Type I, Type II, and Type III). I-240W-S and I-241W-S indoor ONTs provide the following functions:
• • • • • • •
31.3
four configurable 10/100/1000BASE-T Ethernet interfaces using RJ-45 ports two POTS interfaces using RJ-11 ports single mode fiber (SC/APC connector) IEEE 802.11 Wi-Fi interface to enable wireless access fully G.984 series GPON standard compliant G984.5 standard compliant compliance with FCC part 15 Class B
I-240W-S and I-241W-S software and installation feature support Table 31-2 provides a list of software-based features and installation information supported by I-240W-S and I-241W-S indoor ONTs. Table 31-2 I-240W-S and I-241W-S indoor ONT software feature support
Feature
Chapter/description
Click link for more information
General ONT and MDU overview
General information common to multiple devices and an explanation of general system behaviors.
ONT and MDU overview
Service interface specifications
ONT and MDU general and interface technical specifications
Ethernet interface specifications POTS interface specifications RF video interface specifications for video overlay (I-241W-S ONT only)
Services supported
See the appropriate P-OLT user documentation for service creation procedures and descriptions.
RSSI
ONT and MDU general and interface technical specifications
RSSI specifications
Wi-Fi specifications
ONT and MDU general and interface technical specifications
Wi-Fi specifications
Optical budget
ONT and MDU general and interface technical specifications
ONT optical budget
Location and installation options
How to install and replace an I-240W-S or I-241W-S indoor ONT
Install an I-240W-S or I-241W-S indoor ONT
Activation methods
ONT and MDU overview
SLID entry via Ethernet port
Replace an I-240W-S or I-241W-S indoor ONT
(1 of 2)
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-3
31 I-240W-S and I-241W-S unit data sheet
Feature
Chapter/description
Click link for more information
HTTP management
Information necessary to manage an ONT at a local site using an HTTP interface, CLI interface, CLI interface, or butt set.
Web-based ONT configuration
Statistics and performance monitoring
ONT and MDU statistics and performance monitoring
Performance monitoring statistics for Package D ONTs
Supported UPS configurations
Part numbers, ordering, and deployment configuration overview
ONT and MDU to UPS or power adapter compatibility support
(2 of 2)
31.4
I-240W-S and I-241W-S interfaces and interface capacity Table 31-3 describes the supported interfaces and interface capacity for I-240W-S and I-241W-S indoor ONTs. Table 31-3 I-240W-S and I-241W-S indoor ONT interface connection capacity
ONT type and model
Maximum capacity POTS
10/ 100 BASET
10/ 100/ 1000 BASET
RF video (CATV)
MoCA
VDSL2
E1/T1
Local craft
GPON SC/ APC
I-240W-S
(1)
2
4
1
I-241W-S
(1)
2
4
1
1
Note (1)
I-240W-S and I-241W-S ONTs provide Wi-Fi service without a physical connection.
I-240W-S and I-241W-S connections and components I-240W-S and I-241W-S indoor ONTs are intended for indoor deployment and can be installed vertically, horizontally, or attached to a wall. Other features of these indoor ONTs include
• • • •
an ON/OFF power switch for manual shut down a reset button an external multi-directional antennae Wi-Fi service that is enabled and disabled by Web GUI or TR-064/TR-069
Figure 31-1 shows the physical connections for I-240W-S indoor ONTs.
31-4
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet Figure 31-1 I-240W-S indoor ONT physical connections
I O
USB ports
Wi-Fi Reset POTS Protected button ports Service button (RJ-11)
Ethernet ports (RJ-45)
Fiber Power Power optic connector on/off connector switch 22435
Figure 31-2 shows the physical connections for I-241W-S indoor ONTs. Figure 31-2 I-241W-S indoor ONT physical connections
Reset button
Wi-Fi POTS Protected ports Service button (RJ-11)
Ethernet ports (RJ-45)
Fiber Power optic connector connector
Power F-type on/off coaxial switch connector 22788
Figure 31-3 shows the location of the USB host port at the side of I-240W-S ONTs.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-5
31 I-240W-S and I-241W-S unit data sheet Figure 31-3 I-240W-S indoor ONT physical connections (USB host port)
Internet/ USB host port
I O
22442
Figure 31-4 shows the location of the USB port on I-241W-S indoor ONTs. Figure 31-4 I-241W-S indoor ONT physical connections (USB host port)
USB port 22788
Table 31-4 describes the physical connections for I-240W-S and I-241W-S indoor ONTs. Table 31-4 I-240W-S and I-241W-S indoor ONT physical connections Connection (1)
Description
Ethernet ports
This connection is provided through Ethernet RJ-45 cables. Up to four 10/100/1000 Base-T Ethernet interfaces are supported.The Ethernet ports can support both data and in-band video services on all four interfaces.
POTS
This connection is provided through RJ-11 ports. Up to two POTS connections are supported.The POTS ports support voice services.
(1 of 2)
31-6
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet
Connection (1)
Description
WPS button
The Wi-Fi Protected Setup switch is labelled WPS. This button enables and disables the WPS mode.
RF video coaxial
This connection is provided through a F-Type coaxial connector. This connection is found only on the I-241W-S indoor ONT.
Power
This connection is provided through the power connector. A power cable fitted with a Molex connector is used to make the connection.
Fiber optic
This connection is provided through a GPON SC/APC fiber optic connector.
USB ports
On I-240W-S indoor ONTs, this connection is provided through the following USB ports:
•
Two USB host interfaces, compliant to USB 2.0, are supported (one of the USB ports is not powered). One USB host port, compliant to USB 2.0, with a Motive dongle.
•
On I-241W-S indoor ONTs, this connection is provided by one USB host port, compliant to USB 2.0. Cables with A-type connectors are used to connect to the USB ports. (2 of 2) Note (1)
31.5
The primary path for the earth ground for these ONTs is provided by the 12V Return signal in the power connector.
I-240W-S and I-241W-S LEDs Figure 31-5 shows the I-240W-S and I-241W-S indoor ONT LEDs. Figure 31-5 I-240W-S and I-241W-S indoor ONT LEDs
GPON Power WAN Link/Act
4
GPON Power WAN Link/Act
VoIP
Gigabit Ethernet 3 2
4
Gigabit Ethernet 3 2
1
2
1
Wi-Fi WPS USB
VoIP 1
2
1
Wi-Fi WPS USB
22440
Table 31-5 provides LED descriptions for I-240W-S and I-241W-S indoor ONTs.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-7
31 I-240W-S and I-241W-S unit data sheet Table 31-5 I-240W-S and I-241W-S indoor ONT LEDs Indicator
LED color and behavior
LED behavior description
Power
Off
Power is off
Green solid
Power is on
Off
Broadband physical connection is not present or no IP address assigned
Green flashing
IP connected and IP traffic is passing
Green solid
IP connected and no traffic passing
Red
Device attempted IP connection and failed
WAN
GPON Link/Act
Gigabit Ethernet
Red solid
No GPON signal detected
Red flash
GPON signal detected and ranging
Green solid
GPON connection is up and in-service
Orange flash
OMCI data going through GPON port
Orange solid
GPON connection is up but out-of-service
Off
No Ethernet signal detected
Green flashing
User data going through Gigabit Ethernet port
Green solid
Gigabit Ethernet interface is ready to work
VoIP (without VoIP registration status)
Off
Phone is on-hook
Green solid
Phone is off-hook
VoIP (with VoIP registration status)
Off
VoIP is unregistered
Green solid
VoIP is registered and phone is on-hook
Green flashing
VoIP is registered and phone is off-hook
Wi-Fi
WPS
USB
Off
No radio signal detected
Green flashing
User data going through WLAN port
Green solid
Wi-Fi interface is ready to work
Off
Inactive
Green solid
Success status
Green flashing
In Progress status
Red solid
Error and Session Overlap status
Off
No USB signal detected
Green flashing
Traffic activity on the USB port
Green solid
USB interface is ready to work
I-241W-S indoor ONT only RF Video
31.6
Off
RF is disabled or the video optical band being received is lower than the prescribed limit
Green
RF is enabled and optical signal power is working
I-240W-S and I-241W-S detailed specifications Table 31-6 lists the physical specifications for I-240W-S and I-241W-S indoor ONTs.
31-8
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet Table 31-6 I-240W-S and I-241W-S indoor ONT physical specifications Description
Specification
Height
7.9 in. (20 cm)
Width
5.9 in. (15.1 cm)
Depth
1.8 in. (4.6 cm)
Weight including fiber storage tray [within & 0.5 lb (0.23 kg)]
1.5 lb (660 g)
Table 31-7 lists the power consumption specifications for I-240W-S and I-241W-S indoor ONTs. Table 31-7 I-240W-S and I-241W-S indoor ONT power consumption specifications Mnemonic
Maximum power (Not to exceed)
Condition
Minimum power
Condition
I-240W-S
less than 30 W
2 POTS off-hook, 4 Gig-E, Wi-Fi operational
8W
2 POTS on-hook, other interfaces/services not provisioned
I-241W-S
less than 24 W
2 POTS off-hook, 4 Gig-E, 1 RF video, Wi-Fi operational
7.6 W
2 POTS on-hook, other interfaces/services not provisioned
Table 31-8 lists the environmental specifications for I-240W-S and I-241W-S indoor ONTs. Table 31-8 I-240W-S and I-241W-S indoor ONT environmental specifications Mounting method Desk or wall mounted
Temperature range and humidity
Altitude
Operating:(1)
Contact your Alcatel-Lucent technical support representative for more information
-4"F to 122"F (-20"C to 50"C) ambient temperature 20% to 90% relative humidity, non-condensing Storage: Contact your Alcatel-Lucent support representative for more information
Note (1)
When an I-240W-S ONT is used with a power adapter, the maximum operating temperature is 122"F (50"C) while the maximum temperature for an I-240W-S ONT used with an uninterrupted power supply (UPS) is 104"F (40"C).
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-9
31 I-240W-S and I-241W-S unit data sheet
31.7
I-240W-S and I-241W-S GEM ports and T-CONTs Table 31-9 lists the maximum number of supported T-CONTs and GEM ports. Not all ONTs will be supported in all of the releases indicated the table. See the appropriate release Customer Release Notes for the most accurate list of supported devices.
Table 31-9 I-240W-S and I-241W-S indoor ONT capacity for GEM ports and T-CONTs per package and release ONT or MDU
Release
Maximum
Notes
GEM ports per indoor or outdoor ONT
R04.02.56
32
32 are present
T-CONTs per indoor or outdoor ONT
R04.02.56
32
32 are present: 31 are available, 1 is reserved for OMCI
Package D ONTs
31.8
I-240W-S and I-241W-S power support I-240W-S and I-241W-S indoor ONTs support the following power supply:
• CyberPower CyberShield CSN27U12V UPS unit data sheet
31.9
I-240W-S and I-241W-S functional blocks Table 31-10 describes the supported interfaces for I-240W-S and I-241W-S indoor ONTs. Table 31-10 I-240W-S and I-241W-S indoor ONT interfaces
ONT category description
Interface capacity POTS ports
Ethernet ports
2
4
Single-residence Wi-Fi ONTs with Gig-E ONTs, POTS, and with or without RF video (I-240W-S and I-241W-S)
VDSL2
MoCA
RF Video
HPNA
0/1
Wi-Fi 1
I-240W-S and I-241W-S indoor ONTs are single-residence ONTs that support Wireless (Wi-Fi) service. Wi-Fi service on these ONTs are compliant with the IEEE 802.11 standard and enabled or disabled using a radio on/off switch. In addition to the Wi-Fi service, these ONTs transmit Ethernet packets to four RJ-45 Ethernet ports, and voice traffic to two RJ-11 POTS ports. The I-241W-S ONT also supports RF video traffic on one F-type coaxial connector. Both ONTs feature fiber optic and power connectors.
31-10
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet
Figure 31-6 shows functional blocks for I-240W-S indoor ONTs. Figure 31-6 Single-residence Wi-Fi ONT with Gigabit Ethernet and POTS and without RF video Diplexer
GPON SOC
USB Internal Host
RESET WiFi switch
USB Enternal Host
POTS
GE PHY switch
2xUSB
2xRJ11
4xRJ45
PWR 22458
Figure 31-7 shows functional blocks for the I-241W-S indoor ONT which has the same functional blocks as the I-240W-S indoor ONT except for having a triplexer, rather than a diplexer, and an RF video filter. Figure 31-7 Single-residence Wi-Fi ONT with Gigabit Ethernet and POTS and with RF video Triplexer
RF Filter GPON SOC
USB Internal Host
F-type connector
RESET WiFi switch
USB Enternal Host
POTS
GE PHY switch
2xUSB
2xRJ11
4xRJ45
PWR 22570
ONT SoC technology serves as the main hardware block for these ONTs; see Figure 31-8.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-11
31 I-240W-S and I-241W-S unit data sheet Figure 31-8 I-240W-S and I-241W-S ONT hardware block POTS ports
Control processor
SoC
DSP
SoC Bridge
Ethernet MACs
GPON MAC
Ethernet ports
GPON 19421
ONT SoC technology consists of five key elements:
• GPON MAC
• •
•
•
The Gigabit Passive Optical Network Media Access Control (GPON MAC) element on the SoC terminates the GPON interface using an optical diplexer. This interface supports GPON as described in G.984.3 (GPON TC Layer) ITU specification. Ethernet MAC The SoC provides up to four GE MACs. DSP interface The Digital Signal Processor (DSP) provides voice processing for 2 POTS lines with the 3-way calling. The DSP has a dedicated 64 kbyte instruction cache and shares a 32 kbyte data cache with the Control Processor. Control Processor The Control Processor features an integral memory management unit that supports a dedicated 64 kbyte instruction cache and shares a single 32 kbyte data cache with the DSP. The Control Processor and DSP also include a single channel Data Management Application (DMA) controller with a 4 kbyte read ahead low-latency Dynamic Random Access Memory (DRAM) access port. The processors typically run at 400 MHz. Switch matrix The Switch matrix provides an integrated data channel between the four GE MACs, the GPON MAC, the DSP, the control processor, and the other integrated elements such as flash memory, DRAM, and the local bus controller.
These ONTs can also interact with additional hardware components to support functionality not provided by the SoC technology.
31-12
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet
31.10
I-240W-S and I-241W-S standards compliance I-240W-S and I-241W-S indoor ONTs are compliant with the following standards:
• 802.11b support for maximum transmit power (EIRP) equal to or greater than 200 mW (23.01 dBm)
• 802.11g support for maximum transmit power (EIRP) equal to or greater than 100 • • • •
31.11
mW (20 dBm) 802.11n support for wireless LAN interface G.984 support GPON interface (framing) G.984.2 support for Amd1, class B+ G984.5 support for optical and other transport network infrastructures
I-240W-S and I-241W-S special considerations I-240W-S and I-241W-S indoor ONT considerations and limitations Table 31-11 lists the considerations and limitations for I-240W-S and I-241W-S ONTs. Table 31-11 I-240W-S and I-241W- S ONT considerations and limitations Considerations and limitations The ONT only supports OMCIv2 provisioning model Voice management using TR-069/TR-104 is not supported Performance Counters for SIP Voice is not supported Emergency call alarming or forced-hold is not supported The ONT pads packets up to 104 No support for IGMP on PPPoE sessions No support for MAC learning No support for UPnP AV compatibility - Detect DMS device No support for UPnP AV compatibility - can play audio, video, photo file No support for UPnP Applications - eMule, PPStream, UTorrent, Windows Media player 11 No support for Playback WAV format using UPnP AV server
Upgrade considerations and limitations Existing ONTs that use 7342 ISAM FTTU releases older than R04.06.xx and R04.07.xx must be upgraded to use R04.00.10 software while assigned to a PON ID value smaller than 64. For this purpose, if split ratios larger than 1:64 are being deployed, you may choose to set aside the first PON ID as a staging point.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-13
31 I-240W-S and I-241W-S unit data sheet
I-240W-S and I-241W-S indoor ONTs support voice, video, and data services. These ONTs, which feature Wi-Fi technology, can also function as a residential gateway with layer 2 and layer 3 processing capabilities.
I-240W-S and I-241W-S ONT supported features The I-240W-S and I-241W-S ONT supports one of two modes at any given time. The supported modes are
• ONT • Residential gateway You determine which of the two modes is configured by downloading the designated software release. ONT mode
When operating in ONT mode, I-240W-S and I-241W-S ONTs have four Gig-E and two POTS ports while the Wi-Fi service and USB modules are disabled. I-240W-S and I-241W-S indoor ONTs support the following services controlled by OLT:
• VoIP • L2 bridging • Multicast Table 31-12 describes the services supported by I-240W-S and I-241W-S indoor ONTs when in ONT mode. Table 31-12 Supported services in ONT mode Supported services
Description
VoIP
The IP host interface is dedicated for VoIP service The SIP protocol (RFC3261) is ported to the ONT. VoIP-related parameters are configured through the OMCI protocol and downloading the VoIP XML file to the ONT. See VoIP overview for details about the XML download files.
L2 bridging
Each Ethernet port supports the following
• • •
VLAN tagging VLAN/p-bit transparent VLAN/p-bit translation
The following OLT VLAN modes are supported
• • • • Multicast
C-VLAN cross-connect S+C-VLAN cross-connect S-VLAN tunnel cross-connect C-VLAN residential-bridge
IGMP snooping 64 multicast groups
31-14
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet
Residential gateway ONT mode
When operating in Residential gateway ONT mode, I-240W-S and I-241W-S ONTs have one virtual Ethernet IP and two POTS ports. I-240W-S and I-241W-S indoor ONTs support the following services:
• • • •
VoIP L3 routing Residential gateway interfaces Multicast
VoIP service is controlled by OMCI while OLT is reserved for configuring L2 bridging and Multicast services for the L3 routing interface. Established L3 routing can be managed using Access Control Server (ACS). Table 31-13 describes the services supported by I-240W-S and I-241W-S indoor ONTs in Residential gateway mode. Table 31-13 Supported services in Residential gateway ONT mode Supported services
Description
VoIP
The IP host interface is dedicated for VoIP service The SIP protocol (RFC3261) is ported to the ONT. VoIP-related parameters are configured through the OMCI protocol and downloading the VoIP XML file to the ONT. See VoIP overview for details about the XML download files.
L3 routing
Each Ethernet port supports the following
• • •
VLAN tagging VLAN/p-bit transparent VLAN/p-bit translation
OLT must be used to configure the VLAN/p-bit used by the following services:
• • •
HSI IPTV including VoD and Multicast service Management
After the OLT has configured the L2 bridging path for the L3 routing interface, the Residential gateway service can be controlled remotely by ACS using the TR-069 protocol. (1 of 2)
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-15
31 I-240W-S and I-241W-S unit data sheet
Supported services
Description
Residential gateway interfaces
Both LAN and WAN connections are provided. On the up to four WAN connections on the WAN side the following services are provided
• • • •
HSI internet service IPTV including VoD and Multicast service TR-069 remote management VoIP (ACS-controlled VoIP service)
Only the HSI and IPTV interfaces are used for routing services for LAN devices. The traffic on other interfaces terminates at the ONT. IPoE and PPPoE can be configured for each interface with the exception of the IPTV interface which does not support the PPPoE mode. On the two LAN connections the following services are provided
•
•
Multicast
Home network interface is the main interface includes four Ethernet ports, one Wi-Fi AP, and one USB interface. All of these interfaces are bridged. The user on this interface can access HSI and IPTV services. From the LAN side, web GUIs and TR-064 are used to manage the ONT. UPnP IGD and DLNA services are not supported on this interface. Guest network interface is an extra LAN interface with only one Wi-Fi AP attached. Guests can access HSI and IPTV services but can not access the ONT management interface. UPnP IGD and DLNA services are not supported on this interface.
IGMP snooping for home network interface IGMP proxy for WAN IPTV interface Multicast service is not supported on the guest network interface
(2 of 2)
Wi-Fi service I-240W-S and I-241W-S indoor ONTs feature Wi-Fi service as well as voice, video, and data services. Wi-Fi is a wireless networking technology that uses radio waves to provide wireless HSI and network connections. This ONT complies with the IEEE 802.11 standards, which the Wi-Fi Alliance defines as the basis for Wi-Fi technology. Wi-Fi physical features
I-240W-S and I-241W-S indoor ONTs have the following physical features that assist in providing Wi-Fi service:
• one external multi-directional antennae • Wi-Fi Protected Setup (WPS) push button, with indicator LED, for adding WPS-enabled wireless devices Wi-Fi standards, certifications and services
The Wi-Fi service on I-240W-S and I-241W-S indoor ONTs support the following standards and Wi-Fi Alliance certifications:
• compliant with IEEE 802.1x EAP encapsulation • certified for IEEE 802.11b/g/n standards • multiple SSID and WDS
31-16
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet
• WEP, WPA, and WPA2 • MAC address filtering ONT management features I-240W-S and I-241W-S indoor ONTs support management using the following methods:
• • • •
Web GUI using HTTP OMCI interface VoIP xml TR-069
Contact your Alcatel-Lucent technical support representative for more information about ONT management for I-240W-S and I-241W-S indoor ONTs.
Web-based ONT configuration I-240W-S and I-241W-S indoor ONTs support limited configuration using a web-based GUI. The following types of configuration and information retrieval procedures can be performed using the GUI:
• • • • • •
supported device information supported ONT information supported RGW supported VoIP supported diagnosis supported management
Supported Device information I-240W-S and I-241W-S indoor ONTs support limited retrieval of supported device information using a web-based GUI. The following status information can be retrieved using a GUI:
• General status • Transceiver status • UPS status Procedure 31-1 General status information retrieval 1
Select Device Info from the top-level menu in the GPON Web-Management System window.
2
Select the General Status option from the Device Info menu. The Device Information -> General Status window appears; see Figure 31-9.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-17
31 I-240W-S and I-241W-S unit data sheet Figure 31-9 General Status window
Table 31-14 describes the fields in the General Status window.
31-18
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet Table 31-14 General Status parameters
3
Field
Description
Software Version
Identifying the software version currently. Example: 3FE54278AOAA18
Hardware Version
A string identifying the particular CPE model and version. Example: REV1.0
System Time
The current date and time in the CPE
Uptime
Time since the CPE was last restarted
Board ID
Board ID of the CPE
Build Timestamp
Build date and time of the current software
Boatloader (CFE) Version
Identifying the software version currently. Example: 1.0.37-111.26
Wireless Driver Version
A string identifying the particular wireless driver version. Example: 5.100.96.0.cpe4.11L03.13
STOP. This procedure is complete.
Procedure 31-2 Transceiver status information retrieval 1
Select Device Info from the top-level menu in the GPON Web-Management System window.
2
Select the Transceiver Status option from the Device Info menu. The Device Information -> Transceiver Status and Threshold window appears; see Figure 31-10.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-19
31 I-240W-S and I-241W-S unit data sheet Figure 31-10 Transceiver Status and Threshold window
Table 31-15 describes the fields in the Transceiver Status and Threshold window. Table 31-15 Transceiver Status and Threshold parameters
3
Field
Description
Temperature
Current temperature of the CPE. The unit is degree centigrade (C).
RX Power
Current RX power of the CPE. The unit is dbm.
TX Power
Current TX power of the CPE. The unit is dbm.
Voltage
Current voltage of the CPE
STOP. This procedure is complete.
Procedure 31-3 UPS status information retrieval 1
Select Device Info from the top-level menu in the GPON Web-Management System window.
2
Select the UPS Status option from the Device Info menu. The Device Information -> UPS Status window appears; see Figure 31-11.
31-20
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet Figure 31-11 UPS Status window
Table 31-16 describes the fields in the UPS Status window. Table 31-16 UPS status parameters
3
Field
Description
Status
Show current UPS status of the CPE
STOP. This procedure is complete.
Supported ONT information I-240W-S and I-241W-S indoor ONTs support limited retrieval of supported ONT information using a web-based GUI. The following status information can be retrieved using a GUI:
• • • •
GPON Multicasting IP Host VEIP
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-21
31 I-240W-S and I-241W-S unit data sheet
Procedure 31-4 GPON status information retrieval 1
Select ONT from the top-level menu in the GPON Web-Management System window.
2
Select the GPON option from the ONT menu. The ONT -> GPON window appears; see Figure 31-12. Figure 31-12 GPON window
Table 31-17 describes the fields in the GPON window displayed below the Serial Number. Table 31-17 GPON parameters
3
31-22
Field
Description
Password (ASCII)
Set GPON password with ASCII characters
Password (hex)
Set GPON password with hexadecimal characters
Click Apply/Save.
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet See the GPON Status, Mapping, and Statistics information in the window. 4
Click Refresh to update the GPON status, mapping, and statistics information in the window.
5
STOP. This procedure is complete.
Procedure 31-5 Multicasting status information retrieval 1
Select the ONT option from the top-level menu in the GPON Web-Management System window.
2
Select the Multicasting option from the ONT menu. The ONT -> Multicasting window appears; see Figure 31-13. Figure 31-13 Multicasting window
Table 31-18 describes the fields in the Multicasting window.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-23
31 I-240W-S and I-241W-S unit data sheet Table 31-18 Multicasting parameters Field
Description
Status
Index and active group ID information is displayed.
3
STOP. This procedure is complete.
Procedure 31-6 IP Host information retrieval 1
Select ONT from the top-level menu in the GPON Web-Management System window.
2
Select the IP Host option from the ONT menu. The ONT -> IP Host window appears; see Figure 31-14. Figure 31-14 IP Host window
Table 31-19 describes the fields in the IP Host window.
31-24
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet Table 31-19 IP Host parameters
3
Field
Description
IP address
Current IP address of IP host
Subnet Mask
Current subnet mask of IP host
Gateway
Current Gateway of IP host
DNS Server
Current DNS Server of IP host
Mode
Current addressing mode of IP host
RX Statistics
RX statistics of IP host
TX Statistics
TX statistics of IP host
STOP. This procedure is complete.
Procedure 31-7 VEIP status information retrieval 1
Select ONT from the top-level menu in the GPON Web-Management System window.
2
Select the VEIP option from the ONT menu. The ONT -> VEIP window appears; see Figure 31-15.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-25
31 I-240W-S and I-241W-S unit data sheet Figure 31-15 VEIP window
Table 31-20 describes the fields in the VEIP window. Table 31-20 VEIP parameters Field
3
RX Statistics
RX statistics of VEIP
TX Statistics
TX statistics of VEIP
STOP. This procedure is complete.
Supported Residential Gateway (RGW) configuration - WAN I-240W-S and I-241W-S indoor ONTs support limited configuration of RGW service using a web-based GUI. The following WAN IPv4 and IPv6 tasks can be performed using the following GUI procedures:
• • • • 31-26
add WAN PPPoE service (IPv4) add WAN IPoE service (IPv4) remove WAN connection (IPv4) retrieve IPv6-related WAN connection information
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet
Procedure 31-8 Add WAN PPPoE service 1
Select the RGW option from the top-level menu in the GPON Web-Management System window.
2
Select the WAN and IPv4 options from the RGW menu. The RGW -> WAN -> IPv4 window appears; see Figure 31-16. Figure 31-16 WAN IPv4 window
3
Configure PPPoE by clicking Add. The WAN Service Configuration window appears; see Figure 31-17.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-27
31 I-240W-S and I-241W-S unit data sheet Figure 31-17 WAN Service Configuration window
4
Configure the parameters for the PPPoE service. Table 31-21 describes the fields to select for the PPPoE service. Table 31-21 PPPoE service parameters
Field
Description
Select WAN Connection type: PPP over Ethernet (PPPoE)
Select for PPPoE service
IP over Ethernet (IPoE) Service Type: (Multiple selections are possible) HSI
Select to provide High Speed Internet
VoIP
Select to provide VoIP service (Not supported yet)
Management
Select to provide TR-069 remote management
Other fields Enter Service Description
Enter a description of the WAN service
Enter 802.1P Priority [0-7]
Enter the priority which is used on egress traffic from this WAN. The value will be ignored when the option Enable DSCP to P-bit for this connection is checked.
(1 of 2)
31-28
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet
Field
Description
Enter 802.1Q VLAN ID [0-4904]
Enter the VLAN used on egress traffic from the WAN
Enable IPv6 for this service
Select, if wanted. IPv6 can only be enabled on HSI service.
Enable IPv4 for this service
Select, if wanted. If enabled, IPv4 will be enabled even if IPv6 is also enabled for this service.
Default connection service (Default gateway)
Select, if wanted. Default gateway can only be set on HSI/IPTV service.
(2 of 2)
5
Click Next to save selections. The PPP Username and Password window appears; see Figure 31-18. Figure 31-18 PPP Username and Password window
6
Configure more parameters for the PPP service. Table 31-22 describes the fields in the PPP Username and Password window. Table 31-22 PPP Username and Password parameters Field
Description
PPP Username
Enter your PPPoE user name
PPP Password
Enter your PPPoE password
(1 of 2)
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-29
31 I-240W-S and I-241W-S unit data sheet
Field
Description
PPPoE Service Name
Enter your PPPoE service name if necessarily
PPPoE AC Name
Enter your PPPoE AC name, if necessary
Authentication Method
Select one authentication method for this PPPoE connection
Enable NAT
Select, if wanted
Enable Firewall
Select, if wanted.
Dial on Demand (with idle timeout timer)
Select, if wanted. If enabled (selected), when this wan service is disconnected for any reason, it is to remain disconnected until the CPE communicate over this service, at which time the CPE automatically attempts to reestablish the wan service. If disabled (non-selected), the CPE automatically attempts to reestablish the service when this wan service is disconnected for any reason.
Use Static IPv4 Address
Select to use static IPv4 address if wanted. You can set the static IP address in the IPv4 address field.
Enable PPP Debug Mode
Select, if wanted
Bridge PPoE Frames between WAN and Local Ports
Select, if wanted. It is used for PPPoE passthrough sessions.
(2 of 2)
7
Click Next to save selections. The DNS Server Configuration window appears; see Figure 31-19.
31-30
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet Figure 31-19 DNS Server Configuration window
8
Configure the parameters for the DNS server. Table 31-23 describes the fields in the DNS Server Configuration window. Table 31-23 DNS server parameters
9
Field
Description
Primary DNS server
Set, if wanted
Secondary DNS server
Set, if wanted
DNS overwrite
Set, if wanted. If enabled, non-empty DNS address can be overridden by a DNS entry received from the WAN service.
Click Next to save your changes. The WAN Setup -> Summary window appears; see Figure 31-20.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-31
31 I-240W-S and I-241W-S unit data sheet Figure 31-20 WAN Setup - Summary window
10
Click Apply/Save after reviewing the WAN setup. The RGW -> WAN -> IPv4 window appears; see Figure 31-21.
31-32
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet Figure 31-21 WAN IPv4 window
11
STOP. This procedure is complete.
Procedure 31-9 Add WAN IPoE server 1
Select the RGW option from the top-level menu in the GPON Web-Management System window.
2
Select the WAN and IPv4 options from the RGW menu. The RGW -> WAN -> IPv4 window appears; see Figure 31-22.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-33
31 I-240W-S and I-241W-S unit data sheet Figure 31-22 WAN IPv4 window
3
Configure IPoE by clicking Add. The WAN Service Configuration window appears; see Figure 31-23.
31-34
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet Figure 31-23 WAN Service Configuration window
4
Configure the parameters for the IPoE service. Table 31-24 describes the fields to select for the IPoE service. Table 31-24 IPoE service parameters
Field
Description
Select WAN Connection type PPP over Ethernet (PPPoE) IP over Ethernet (IPoE)
Select for IPoE service
Service type: (Multiple selections are possible) HSI
Select to provide High Speed Internet
VoIP
Select to provide VoIP service (Not supported yet)
IPTV
Select to provide Video service
Management
Select to provide TR-069 remote management
Other fields Service Description
Enter a description of the WAN service
(1 of 2)
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-35
31 I-240W-S and I-241W-S unit data sheet
Field
Description
Enter 802.1P Priority [0-7]
Enter the priority used on egress traffic from this WAN. The value will be ignored when the option Enabled DSCP to P-bit for this connection is checked.
Enter 802.1Q VLAN ID [0-4904]
Enter the VLAN used on egress traffic from this WAN
Enable IPv6 for this service
Select, if wanted. IPv6 can only be enabled on HSI service
Enable IPv4 for this service
Select, if wanted. If enabled, IPv4 will be enabled even if IPv6 is also enabled for the service.
Default connection service (Default gateway)
Select, if wanted. Default gateway can only be set on HSI/IPTV service.
(2 of 2)
5
Click Next to save selections. The WAN IP Settings window appears; see Figure 31-24. Figure 31-24 WAN IP Setting window
6
Configure the parameters for the WAN IP settings. Table 31-25 describes the fields in the WAN IP Settings window.
31-36
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet Table 31-25 WAN IP settings parameters Field
Description
Obtain an IP address automatically
Select, if wanted. If set, the IP address/Netmask/gateway of the service will be assigned automatically by DHCP server. Note: the PC on LAN side should have DHCP server.
Option 60 Vendor ID
Set, if wanted. Empty string means disable the option.
Use the following Static IP address:
Select, if wanted. If set, the IP address/Netmask/gateway of the service should be set in below field manually.
WAN IP Address
Set static IP address of this service.
WAN Subnet Mask
Set static netmask of this service.
WAN gateway IP Address
Set static gateway of this service.
7
Click Next to save your changes.
8
To modify the configuration of the NAT or firewall, select RGW from the top-level menu in the GPON Web-Management System window.
9
Select the NAT option from the RGW menu. The Network Address Translation Settings window appears; see Figure 31-25.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-37
31 I-240W-S and I-241W-S unit data sheet Figure 31-25 Network Address Translation setting window
10
Configure the parameters for the NAT or Firewall service. Table 31-26 describes the fields to select for the Network Address Translation Settings window. Table 31-26 Network Address Translation settings parameters
Field
Description
Enable NAT
Select, if wanted
Enable Firewall
Select, if wanted
11
Click Next to save your changes. The DNS Server Configuration window appears; see Figure 31-26.
31-38
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet Figure 31-26 DNS Server Configuration window
12
Configure the parameters for the DNS server. Table 31-27 describes the fields in the DNS Server Configuration window. Table 31-27 DNS server parameters
Field
Description
Primary DNS server
Set, if wanted
Secondary DNS server
Set, if wanted.
DNS overwrite
If enabled (selected), non-empty DNS address can be overridden by a DNS entry received from the WAN service.
13
Click Next to save your changes. The WAN Setup - Summary window appears; see Figure 31-27.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-39
31 I-240W-S and I-241W-S unit data sheet Figure 31-27 WAN Setup - Summary window
14
Click Apply/Save after reviewing the WAN setup. The RGW -> WAN -> IPv4 window appears; see Figure 31-28.
31-40
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet Figure 31-28 WAN IPv4 window
15
STOP. This procedure is complete.
Procedure 31-10 Remove a WAN connection 1
Select RGW from the top-level menu in the GPON Web-Management System window.
2
Select the WAN and IPv4 options from the RGW menu. The WAN IPv4 window appears; see Figure 31-29.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-41
31 I-240W-S and I-241W-S unit data sheet Figure 31-29 WAN IPv4 window
3
Highlight the WAN connection or connections you want removed.
4
Click Remove to save your changes. The WAN IPv4 window appears with the selected WAN connection deleted; see Figure 31-30.
31-42
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet Figure 31-30 WAN IPv4 window
5
STOP. This procedure is complete.
Procedure 31-11 Retrieve IPv6-related WAN information The following procedure provides the steps to reactive IPv6-related information for WAN connections. 1
Select RGW from the top-level menu in the GPON Web-Management System window.
2
Select the WAN and IPv6 options from the RGW menu. The RGW -> WAN -> IPv6 window appears; see Figure 31-31.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-43
31 I-240W-S and I-241W-S unit data sheet Figure 31-31 WAN IPv6 window
3
STOP. This procedure is complete.
Supported Residential Gateway (RGW) configuration - LAN I-240W-S and I-241W-S indoor ONTs support limited configuration of RGW service using a web-based GUI. The following LAN tasks can be performed using a GUI:
• set br0 • set br1 (not supported by IPv6) Procedure 31-12 Set br0 1
Select RGW from the top-level menu in the GPON Web-Management System window.
2
Select the LAN option from the RGW menu. The RGW -> LAN window appears; see Figure 31-32.
31-44
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet Figure 31-32 LAN window
3
Configure the parameters for the LAN service. Table 31-28 describes the fields to select for the LAN IPv4 service. Table 31-28 LAN IPv4 service parameters
Field
Description
Configure the Broadband Router, ID Address, and Subnet mask for LAN interface
Select br0 from the drop-down menu
Setup -- IPv4: IP Address
Set static IP address if the DHCP Client is not be selected.
Subnet mask
Set subnet mask if the DHCP Client is not be selected.
Enable DHCP Client
Select, if wanted. If enabled, the IP address/subnet mask of br1 will be assigned automatically by DHCP server.
DHCP IP Address
Show the DHCP IP address.
DHCP Subnet Mask
Show the DHCP subnet mask.
Start IP Address
Set the first address to be assigned by the DHCP server on the LAN interface. It is used when Enable DHCP Server field is selected.
End IP Address
Set the last address to be assigned by the DHCP server on the LAN interface. It is used when Enable DHCP Server field is selected.
(1 of 2)
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-45
31 I-240W-S and I-241W-S unit data sheet
Field
Description
Learned Time (hour)
Set the lease time in hours of client assigned addresses. It is used when Enable DHCP Server field is selected.
(2 of 2)
4
Click Apply/Save to save selections.
5
Configure more parameters for the LAN service. Table 31-29 describes the fields in the RGW -> LAN window but not part of the Setup -- IPv4 section. Table 31-29 LAN service parameters
6
Field
Description
Static IP Lease List (A maximum 32 entries can be configured)
Add or remove items from this list
Reserved IP Address List (A maximum 10 entries can be configured)
Add or remove items from this list
DHCP Leases
DHCP Leases table list can not be added or removed manually
Click Add or Remove to save selections. See the Setup -- IPv6 section of the LAN window; see Figure 31-33.
31-46
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet Figure 31-33 Setup -- IPv6 section of LAN window
7
Scroll down in the RGW -> LAN window. The Setup -- IPv6 section appears; see Figure 31-34.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-47
31 I-240W-S and I-241W-S unit data sheet Figure 31-34 Setup -- IPv6 section of LAN window
8
Configure the parameters for the LAN IPv6 service. Table 31-30 describes the fields in the IPv6 LAN Applications window. Table 31-30 IPv6 LAN application parameters Field
Description
Enable RADVD
Enable to publish prefix and route information
MaxRtrAdvInterval(s)
Set the maximum interval of sending RA packets
MinRtrAdvInterval(s)
Set the minimum interval of sending RA packets.
Router Life Time(s)
Set the lifetime associated with the route in units of seconds
Enable ULA Prefix Advertisement
Enable state of ULA (Unique Local Address) Prefix
Prefix
Set the ULA prefix
Preferred Life Time (hour)
Set the preferred lift time of the prefix (in hours) published in Router Advertisement
(1 of 2)
31-48
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet
Field
Description
Valid Life Time (hour)
Set the valid life time of the prefix (in hours) published in Router Advertisement. Prefix Valid Lifetime must always be larger than or equal to Prefix Preferred Lifetime.
Enable DHCPv6 server
Enable DHCPv6 server in LAN side
Publish self as DNS server
Set if wanted. Enable to publish clients IPv6 address in LAN side as DNS server
Stateless
Enable stateless mode
Stateful
Enable stateful mode
Start interface ID
Set value which indicates the beginning of the interface ID pool. Interface ID does not support ZERO COMPRESSION "::". Please enter the complete information. For example: Please enter "0:0:0:2" instead of "::2".
End interface ID
Set value which indicates the end of the interface ID pool. Interface ID does not support ZERO COMPRESSION "::". Please enter the complete information. For example: Please enter "0:0:0:2" instead of "::2".
Leased Time (hour)
Set the preferred life time in hours of client assigned addresses. A setting of -1 indicates an infinite lease.
(2 of 2)
9
Click Apply/Save. Review you changes in the IPv6 LAN Applications window; see Figure 31-35.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-49
31 I-240W-S and I-241W-S unit data sheet Figure 31-35 IPv6 LAN statistics window
10
STOP. This procedure is complete.
Procedure 31-13 Set br1 1
Select RGW from the top-level menu in the GPON Web-Management System window.
2
Select the LAN option from the RGW menu. The RGW -> LAN window appears; see Figure 31-36.
31-50
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet Figure 31-36 RGW -> LAN window
3
Configure the parameters for the LAN service. Table 31-31 describes the fields to select for the LAN service. Table 31-31 LAN IPv4 service parameters
Field
Description
Configure the Broadband Router, ID Address, and Subnet mask for LAN interface
Select br1 from the drop-down menu
Setup -- IPv4: IP Address
Set static IP address if the DHCP Client is not be selected
Subnet mask
Set subnet mask if the DHCP Client is not be selected
Enable DHCP Client
Select, if wanted. If enabled, the IP address of br0 will be assigned automatically by DHCP server.
DHCP IP Address
Show the DHCP IP address
DHCP Subnet Mask
Show the DHCP subnet mask
Enable DHCP Server
Select to enable DHCP server on LAN side
Start IP Address
Set the first address to be assigned by the DHCP server on the LAN interface. It is used when Enable DHCP Server field is selected.
(1 of 2)
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-51
31 I-240W-S and I-241W-S unit data sheet
Field
Description
End IP Address
Set the last address to be assigned by the DHCP server on the LAN interface. It is used when Enable DHCP Server field is selected.
Learned Time (hour)
Set the lease time in seconds of client assigned addresses. It is used when Enable DHCP Server field is selected.
(2 of 2)
4
Click Apply/Save to save selections.
5
Configure more parameters for the LAN service. Table 31-32 describes the fields in the RGW -> LAN window but not part of the Setup -- IPv4 section. Table 31-32 Additional LAN service parameters
6
Field
Description
Static IP Lease List (A maximum 32 entries can be configured)
Add or remove items from this list
Reserved IP Address List (A maximum 10 entries can be configured)
Add or remove items from this list
DHCP Leases
DHCP Leases table list can not be added or removed manually
Click Add or Remove to save selections. The window with information configured in step 5 appears; see Figure 31-37.
31-52
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet Figure 31-37 LAN service window
7
Review the br1 service statistics. The br1 service statistic window appears; see Figure 31-38.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-53
31 I-240W-S and I-241W-S unit data sheet Figure 31-38 br1 service statistic window
8
STOP. This procedure is complete.
Supported Residential Gateway (RGW) configuration - DNS Proxy I-240W-S and I-241W-S indoor ONTs support limited configuration of RGW service including DNS proxy using a web-based GUI.
Procedure 31-14 Configuring DNS proxy 1
Select RGW from the top-level menu in the GPON Web-Management System window.
2
Select the DNS Proxy option from the RGW menu. The RGW -> DNS Proxy window appears; see Figure 31-39.
31-54
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet Figure 31-39 DNS Proxy window
3
Configure the parameters for the DNS Proxy service. Table 31-33 describes the fields to select for the DNS Proxy service. Table 31-33 DNS Proxy service parameters Field
Description
Host name of the Broadband Router
Set host name of the CPE in the LAN network
Domain name of the LAN network:
Set domain name of the LAN network
4
Click Apply/Save to save selections.
5
STOP. This procedure is complete.
Supported Residential Gateway (RGW) configuration - NAT I-240W-S and I-241W-S indoor ONTs support limited configuration of RGW service including NAT using a web-based GUI.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-55
31 I-240W-S and I-241W-S unit data sheet
Procedure 31-15 Configuring NAT 1
Select RGW from the top-level menu in the GPON Web-Management System window.
2
Select the NAT option from the RGW menu. The NAT -> DMZ Host window appears; see Figure 31-40. Figure 31-40 DMZ Host window
3
Configure the parameters for the DMZ host. Table 31-34 describes the fields to set the DMZ. Table 31-34 DMZ Host parameters
31-56
Field
Description
DMZ Host IP Address
Set IP address of DMZ host
4
Click Apply/Save to save selections.
5
Configure the virtual server or port triggering for the DMZ, as shown in Figure 31-40.
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet Table 31-35 describes the virtual server or port triggering fields in the DMZ Host window. Table 31-35 Additional LAN service parameters Field
Description
NAT -- Virtual Servers Setup
Add or remove items from this list
NAT -- Port Triggering Setup
Add or remove items from this list
6
Click Add or Remove to save your NAT setup.
7
STOP. This procedure is complete.
Supported Residential Gateway (RGW) configuration - Routing rule I-240W-S and I-241W-S indoor ONTs support limited configuration of RGW service including routing rule using a web-based GUI. You can select the default gateway if the service type for this connection is either HSI or IPTV. The following routing tasks can be performed using a GUI:
• select a default gateway • add or remove static routes • add or remove a neighbor (supported by IPv6 only) Procedure 31-16 Configuring a default gateway 1
Select RGW from the top-level menu in the GPON Web-Management System window.
2
Select the Routing rule and Default Gateway options from the RGW menu. The Routing -- Default Gateway window appears; see Figure 31-41.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-57
31 I-240W-S and I-241W-S unit data sheet Figure 31-41 Routing -- Default Gateway window
3
Configure the parameters for the Default Gateway. Table 31-36 describes the fields to set the WAN interface. Table 31-36 Default Gateway parameter Field
Description
Selected WAN Interface
Support HSI or IPTV interface only
4
Click Apply/Save to save selections.
5
STOP. This procedure is complete.
Procedure 31-17 Configuring static routes 1
Select RGW from the top-level menu in the GPON Web-Management System window.
2
Select the Routing Rule and Route options from the RGW menu. The Route table window appears; see Figure 31-42.
31-58
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet Figure 31-42 Route table window
3
Configure the static route. Table 31-37 describes the fields to set the static route. Table 31-37 Routing rule parameter Field
Description
Static Route (A maximum 32 entries can be configured)
Add or remove static route from the list. Support HSI or IPTV interface only
4
Click Add or Remove to save your selections.
5
STOP. This procedure is complete.
Procedure 31-18 Configuring an IP neighbor 1
Select RGW from the top-level menu in the GPON Web-Management System window.
2
Select the Routing Rule and Neighbor options from the RGW menu. The IP Neighbor Configuration window appears; see Figure 31-43.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-59
31 I-240W-S and I-241W-S unit data sheet Figure 31-43 IP Neighbor Configuration window
3
Configure the IP Neighbor by clicking Add or Remove to add or delete a neighbor.
4
STOP. This procedure is complete.
Supported Residential Gateway (RGW) configuration - Firewall I-240W-S and I-241W-S indoor ONTs support limited configuration of RGW service including creating firewalls using a web-based GUI. You can add or remove outgoing IP filters or incoming IP filters if there is at least one WAN connection which enables firewalls and the selected service type is either HSI or IPTV.
Procedure 31-19 Configuring user control 1
Select RGW from the top-level menu in the GPON Web-Management System window.
2
Select the Firewall and User Control options from the RGW menu. The RGW -> Firewall -> User Control window appears; see Figure 31-44.
31-60
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet Figure 31-44 RGW -> Firewall -> User Control window
3
Configure the parameters for the Firewall User Control interface. Table 31-38 describes the fields to set the Firewall User Control interface. Table 31-38 Firewall User Control interface parameters Field
Description
Outgoing IP Filtering Setup
Set some outgoing IP filters if wanted. By default, all outgoing IP traffic from LAN is allowed, some IP traffic can be BLOCKED by setting up outgoing IP filters.
br0 Outgoing IP Filtering
Add or remove outgoing IP filters of br0 from list. Filters in "br0 Outgoing IP Filtering" list only take effect on br0 interface.
br1 Outgoing IP Filtering
Add or remove outgoing IP filters of br1 from list. Filters in "br1 Outgoing IP Filtering" list only take effect on br1 interface.
(1 of 2)
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-61
31 I-240W-S and I-241W-S unit data sheet
Field
Description
Incoming IP Filtering Setup
Set some incoming IP filters if wanted. If firewall is enabled on a WAN interface, all incoming IP traffic from LAN is blocked, but some IP traffic can be ACCEPTED by setting up incoming IP filters.
ipoe_veip0.104/veip0.1 Incoming IP Filtering
Add or remove incoming IP filters of specific WAN interface from list. Filters in list only take effect on correspondent interface.
(2 of 2)
4
Click Add or Remove create filters.
5
STOP. This procedure is complete.
Supported Residential Gateway (RGW) configuration - Parental control I-240W-S and I-241W-S indoor ONTs support limited configuration of RGW service including creating time restrictions and URL filters using a web-based GUI. You can add or remove time restrictions or URL filters. The following firewall tasks can be performed using a GUI:
• add or remove time restrictions • add or remove URL filters Procedure 31-20 Configuring time restrictions 1
Select RGW from the top-level menu in the GPON Web-Management System window.
2
Select the Parental Control and Time Restriction options from the RGW menu. The Access Time Restriction window appears; see Figure 31-45.
31-62
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet Figure 31-45 Access Time Restriction window
3
Configure the parameters for the time restrictions. Table 31-39 describes the fields to set time restrictions. Table 31-39 Time restriction parameter Field
Description
Access Time Restriction -- A maximum 16 entries can be configured
Add or remove access time restriction entry from list. The "MAC Address" field should set as MAC address of the PC on LAN side. The traffic comes from the restricted PC on LAN side can't be transmitted in restricted time.
4
Click Add or Remove create or remove time restrictions.
5
STOP. This procedure is complete.
Procedure 31-21 Configuring URL filters 1
Select RGW from the top-level menu in the GPON Web-Management System window.
2
Select the Parental Control and URL Filter options from the RGW menu. The URL Filter window appears; see Figure 31-46.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-63
31 I-240W-S and I-241W-S unit data sheet Figure 31-46 URL Filter window
3
Configure the URL filter. Table 31-40 describes the fields to set the UFL filter. Table 31-40 URL Filter parameters Field
Options
URL List Type
Allow or deny for accessing the specific URL. If "Exclude" is set, all the URL can be accessed except the URL in below list. If "Include" is set, only the URL in below list can be accessed.
4
Add or remove items from this list.
5
STOP. This procedure is complete.
Supported Residential Gateway (RGW) configuration - MAC filter I-240W-S and I-241W-S indoor ONTs support limited configuration of RGW service including adding and removing allowed MAC for br0 and br1 using a web-based GUI.
Procedure 31-22 Configuring MAC filters
31-64
1
Select RGW from the top-level menu in the GPON Web-Management System window.
2
Select the MAC Filter option from the RGW menu.
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet The RGW -> MAC filter window appears; see Figure 31-47. Figure 31-47 RGW -> MAC filter window
3
Click Add Allowed MAC Address to add a MAC filter. The Add MAC Filter window appears; see Figure 31-48. Figure 31-48 Add MAC Filter window
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-65
31 I-240W-S and I-241W-S unit data sheet 4
Configure the parameters for the new MAC filter. Table 31-41 describes the fields to set time restrictions. Table 31-41 MAC filter parameters
5
Field
Options
Group Name
Select br0 or br1 from the drop-down menu
Allowed Mac Address
Enter the MAC address
Click Add to create a new MAC filter. The RGW -> MAC Filter window reappears; see Figure 31-49. Figure 31-49 RGW -> MAC Filter window
6
Configure the parameters for the newly created MAC filter. Table 31-42 describes the fields to configure a br0 or br1 MAC filter. Table 31-42 MAC filter parameters
31-66
Field
Options
br0 Allow MAC address
Select eth0, eth1, eth2, eth3, or wifi_Ap
br1 Allow Mac Address
Select wifi_Ap_guest
7
Click Apply/Save to save selections.
8
STOP. This procedure is complete.
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet
Supported Residential Gateway (RGW) configuration - IP tunnel I-240W-S and I-241W-S indoor ONTs support limited configuration of RGW service including adding and removing IPv4 or IPv6 IP tunnels using a web-based GUI. The following IP tunnel tasks can be performed using a GUI:
• add or remove IPv6 in IPv4 tunnels • add or remove IPv4 in IPv6 tunnels Procedure 31-23 Configuring IP tunnels 1
Select RGW from the top-level menu in the GPON Web-Management System window.
2
Select the IP Tunnel and IPv6 in IPv4 option from the RGW menu. The IP Tunnelling -- 6in4 Tunnel Configuration window appears; see Figure 31-50. Figure 31-50 IP Tunnelling - - 6in4 Tunnel Configuration window
3
Click Add or Remove an IPv6 in IPv4 tunnel configuration.
4
Select RGW from the top-level menu in the GPON Web-Management System window.
5
Select the IP Tunnel and IPv4 in IPv6option from the RGW menu. The IP Tunnelling -- 4in6 Tunnel Configuration window appears; see Figure 31-51.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-67
31 I-240W-S and I-241W-S unit data sheet Figure 31-51 IP Tunnelling - - 4in6 Tunnel Configuration window
6
Click Add or Remove an IPv4 in IPv6 tunnel configuration.
7
STOP. This procedure is complete.
Supported Residential Gateway (RGW) configuration - QoS I-240W-S and I-241W-S indoor ONTs support limited configuration of RGW service including adding and removing QoS or modifying the status of QoS using a web-based GUI.
Procedure 31-24 Configuring QoS 1
Select RGW from the top-level menu in the GPON Web-Management System window.
2
Select the QoS option from the RGW menu. The RGW -> QoS DSCP Marking Setup window appears; see Figure 31-52.
31-68
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet Figure 31-52 RGW -> QoS DSCP Marking Setup window
3
Click Add or Remove to create or delete rules. Check the Remove checkboxes for all the rules you want to delete before clicking Remove.
4
Click Apply/Save to save your selections.
5
Set the DSCP and P-bit mapping table, as shown in Figure 31-52. Table 31-43 describes the fields to set the DSCP and P-bit mapping table. Table 31-43 QoS DSCP to P-bit parameters Field
Options
DSCP
A number from 00 to 63 for each DSCP
P-bit
Select a P-bit number to associate with the DSCP from the drop-down menu
6
Click Apply/Save to save your selections.
7
STOP. This procedure is complete.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-69
31 I-240W-S and I-241W-S unit data sheet
Supported Residential Gateway (RGW) configuration - IGMP Proxy I-240W-S and I-241W-S indoor ONTs support limited configuration of RGW service including setting the IGMP proxy parameters using a web-based GUI.
Procedure 31-25 Configuring IGMP proxy 1
Select RGW from the top-level menu in the GPON Web-Management System window.
2
Select the IGMP Proxy option from the RGW menu. The RGW -> IGMP Proxy window appears; see Figure 31-53 showing the default values. Figure 31-53 RGW -> IGMP Proxy window
3
Configure the IGMP proxy by changing the default values. Table 31-44 describes the fields for setting the IGMP proxy.
31-70
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet Table 31-44 IGMP proxy parameters Field
Description
Default Version
Set IGMP protocol version. Support version IGMPv2(value: 2) and IGMPv3(value: 3) only.
Query Interval
Set query interval. "Query Interval" indicates the amount of time in seconds between IGMP General Query sent to client.
Query Response Interval
Set query response interval. "Query Response Interval" indicates max response time advertised in general queries (seconds).
Last Member Query Interval
Set last member query response interval. "Last Member Query Response Interval" indicates max response time advertised in specific queries (seconds).
Robustness Value
Set robustness value. "Robustness Value" means a way of indicating how susceptible the subnet is to lost packets. IGMP can recover from robustness variable minus 1 lost IGMP packets.
Maximum Multicast Groups
Set maximum number of simultaneous groups supported.
Maximum Multicast Data Sources (for IGMPv3: (1-24)
Set maximum number of multicast data sources.
Maximum Multicast Group Members
Set maximum number of reporters for a group.
LAN to LAN (Intra LAN) Multicast Enable
Set, if wanted. If enabled (selected), the PC on LAN side can be media server and provides IPTV service for other PCs on LAN side.
Enable allowed host
Set, if wanted. Enable allowed host will limits that only the hosts which match a list of allowed host specified in "Allowed Host IP Address List" (see below on this page) can join group.
4
Click Apply/Save to save your selections.
5
Click Add or Remove to set the IGMP profile and Allowed Host IP address list, as shown in Figure 31-53.
6
Click Refresh or Reset to set the Interface Statistic. Table 31-45 describes the fields to configure the interface statistics.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-71
31 I-240W-S and I-241W-S unit data sheet Table 31-45 Interface Statistic parameters
7
Field
Options
eth0
Set V3 Report, V2 Join, V2 Leave, and Drop
eth1
Set V3 Report, V2 Join, V2 Leave, and Drop
eth2
Set V3 Report, V2 Join, V2 Leave, and Drop
eth3
Set V3 Report, V2 Join, V2 Leave, and Drop
wl0
Set V3 Report, V2 Join, V2 Leave, and Drop
STOP. This procedure is complete.
Supported Residential Gateway (RGW) configuration - WLAN I-240W-S and I-241W-S indoor ONTs support limited configuration of RGW service including enabling or disabling scheduling and set active times using a web-based GUI. The following WLAN tasks can be performed using a GUI:
• • • • • •
configure basic WLAN and WLAN security configure WDS configure WLAN scheduling configure advanced WLAN configuring Virtual Access Point displaying Station information
Procedure 31-26 Configuring Basic WLAN and WLAN security 1
Select RGW from the top-level menu in the GPON Web-Management System window.
2
Select WLAN from the RGW menu.
3
Select Basic/Security from the WLAN menu. The Basic window appears; see Figure 31-54.
31-72
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet Figure 31-54 Basic window
4
5
Enable or disable Wireless service by either selecting or clearing the Enable Wireless radio button. a
To enable Wireless service, go to step 5.
b
To disable Wireless service, go to step 6.
Configure the RGW> WLAN> Basic section parameters. Table 31-46 describes the fields in the Basic section of the Basic/Security window. Table 31-46 Basic parameters
Field
Description
Enable wireless
Select the radio button
SSID
Enter the SSID
BSSID
Enable the BSSID
Enable Wireless Guest Network
Select the radio button
(1 of 2)
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-73
31 I-240W-S and I-241W-S unit data sheet
Field
Description
Guest SSID
Enter the SSID for the guest
(2 of 2)
6
Configure the RGW -> WLAN -> Security section parameters. The RGW -> WLAN -> Security window; see Figure 31-55. Figure 31-55 RGW -> WLAN -> Security window
7
Set the Security parameters by entering information in the fields. Table 31-47 describes the fields in the Security section of the window. Table 31-47 Security parameters
Field
Description
WPS Setup
Select Enabled or Disabled from the drop-down menu
(1 of 2)
31-74
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet
Field
Description
Add Client (available only when WPA-PSK, WPAZ PSK, or OPEN mode is configured)
Select either Push-Button, Enter STA PIN, or Use AP PIN before clicking Add Enrollee
Set WPS AP Mode
Select an opinion from the drop-down menu
Setup AP
Enter a Device PIN
Manual Setup AP Select SSID
Select the AP you want to change or see configuration from the drop-down menu
Network Authentication
Select Open or Close from the drop-down menu
WEP Encryption
Select Enabled or Disabled from the drop-down menu
(2 of 2)
8
Click Apply/Save to save your changes. The WLAN received and transmitted statistics appear at the bottom of the window; see Figure 31-56.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-75
31 I-240W-S and I-241W-S unit data sheet Figure 31-56 Statistics in the Security window
9
STOP. This procedure is complete.
Procedure 31-27 Configuring WDS 1
Select RGW from the top-level menu in the GPON Web-Management System window.
2
Select WLAN from the RGW menu.
3
Select WDS from the WLAN menu. The Wireless -- WDS window appears; see Figure 31-57.
31-76
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet Figure 31-57 Wireless -- WDS window
4
Configure the WDS parameters by entering information in the fields. Table 31-48 describes the fields in the Wireless -- WDS window. Table 31-48 Wireless -- WDS parameters
Field
Opinions
AP Mode
Select an opinion from the drop-down menu
Bridge Restrict
Select Enabled or Disabled from the drop-down menu
Remote Bridges MAC Address
Enable MAC address
5
Click Apply/Save to save your changes.
6
STOP. This procedure is complete.
Procedure 31-28 Configuring WLAN scheduling 1
Select RGW from the top-level menu in the GPON Web-Management System window.
2
Select WLAN from the RGW menu.
3
Select Scheduling from the WLAN menu. The RGW -> WLAN -> Scheduling window appears; see Figure 31-58.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-77
31 I-240W-S and I-241W-S unit data sheet Figure 31-58 RGW -> WLAN -> Scheduling window
4
Configure the Scheduling parameters by entering information in the fields. Table 31-49 describes the fields in the Wireless -- WDS window. Table 31-49 RGW -> WLAN -> Scheduling parameters
Field
Opinions
Enable Wireless Scheduling
Select or de-select the radio button
Day
Click on the days wanted for scheduling
Start Restriction Time
Enter hours and minutes
End Restriction Time
Enter hours and minutes
5
Click Apply/Save to save your changes.
6
STOP. This procedure is complete.
Procedure 31-29 Configuring advanced WLAN
31-78
1
Select RGW from the top-level menu in the GPON Web-Management System window.
2
Select WLAN from the RGW menu.
3
Select Advanced from the WLAN menu.
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet The RGW -> WLAN -> Advanced window appears; see Figure 31-59. Figure 31-59 RGW -> WLAN -> Advanced window
4
Configure the Advanced parameters by entering information in the fields. Table 31-50 describes the fields in the RGW -> WLAN -> Advanced window. Table 31-50 RGW -> WLAN -> Advanced parameters
Field
Opinions
Hide Access Point
Select or de-select the radio button
Clients Isolation
Select or de-select the radio button
Disable WMM Advertise
Select or de-select the radio button
Enable Wireless Multicast Forwarding (WMF)
Select or de-select the radio button
Country
Select a country from the drop-down menu
Max Clients
Enter the maximum number of clients
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-79
31 I-240W-S and I-241W-S unit data sheet 5
Configure the remaining Advanced parameters by entering information in the fields. These parameters are shown in Figure 31-60. Figure 31-60 RGW -> WLAN -> Advanced window
Table 31-51 describes the fields in the RGW -> WLAN -> Advanced window. Table 31-51 RGW -> WLAN -> Advanced parameters Field
Opinions
Band
Select the frequency band from the drop-down menu. Support 2.4GHz only.
Channel
Select the working channel from the drop-down menu. The channel is used as the channel on which the AP found the network.
Auto Channel Timer (min)
Show the auto channel timer
802.11n/EWC
Enable 802.11n/EWC or not
Bandwidth
Select the bandwidth from the drop-down menu.
(1 of 2)
31-80
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet
Field
Opinions
Control Sideband
Select the control side band on the AP from the drop-down menu
802.11n Rate
Select the fixed rate for IEEE 802.1n standard on the AP from the drop-down menu
802.11n Protection
Enable 802.11n protection or not. If the "Auto" is selected, protection mechanisms will be used for IEEE 802.11n standard.
Support 802.11n Client Only
Enable Support 802.11n Client Only or not.
RIFS Advertisement
Enable RIFS (Reduced Inter frame Space) Advertisement or not.
OBSS Co-Existence
Enable OBSS Co-Existence or not. If enabled, BSSIDs can operate within the same frequency range.
RX Chain Power Save
Enable RX chain power save mechanism or not
RX Chain Power Save Quest Time
Enter RX Chain Power Save Quest Time
RX Chain Power Save PPS
Enter RX Chain Power Save PPS
54g Rate
Select fixed rate for 802.11b/g from the drop-down menu
Multicast Rate
Select fixed multicast rate for 802.11b/g from the drop-down menu.
Basic Rate
Select an opinion from the drop-down menu
Fragmentation Threshold
Enter the fragmentation threshold. Fragmentation Threshold indicates the maximum frame size wireless device can transmit without fragmenting the frame.
RTS Threshold
Enter the RTS threshold. RTS Threshold indicates the RTS (Request-to-send) packets are a mechanism used by the 802.11 wireless networking protocol which establish an open communication to an AP or node.
DTIM Interval
Enter the DTIM interval. The AP is generated within the periodic beacon at a frequency specified by the DTIM Interval.
Beacon Interval
Enter the Beacon interval. The Beacon Interval indicates the time interval between beacon transmissions.
Global Max Clients
Enter the global max clients. Global Max Clients indicates the maximum clients which can be associated with all APs on this CPE.
XPress Technology
Enable XPress Technology or not. Enable XPress technology will achieve higher throughput by re-packaging data, reducing the number of overhead control packets, so that more useful data can be sent during a given amount of time.
Transmit Power
Select the transmit power from the drop-down menu. Transmit power indicates the current transmit power level as a percentage of full power.
WMM (Wi-Fi Multimedia)
Enable WMM or not
WMM No Acknowledgement
Enable WMM No Acknowledgement or not
WMM APSD
Enable WMM APSD or not
(2 of 2)
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-81
31 I-240W-S and I-241W-S unit data sheet 6
Click Apply/Save to save your changes.
7
STOP. This procedure is complete.
Procedure 31-30 Configuring Virtual Access Point 1
Select RGW from the top-level menu in the GPON Web-Management System window.
2
Select WLAN from the RGW menu.
3
Select Virtual Access Point from the WLAN menu. The RGW -> WLAN -> Virtual Access Point window appears; see Figure 31-61. Figure 31-61 RGW -> WLAN -> Virtual Access Point window
4
Configure the Virtual Access Point parameters by entering information in the fields. Table 31-52 describes the fields in the RGW -> WLAN -> Virtual Access Point window. Table 31-52 RGW -> WLAN -> Virtual Access Point parameters Field
Description
Enabled
Set to enable this virtual access point.
SSID
Set SSID of this virtual access point.
Hidden
Set, if wanted. If set, the virtual access point will not be found on network.
Disable WMM Advertise
Set, if wanted.
(1 of 2)
31-82
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet
Field
Description
Enable WMF
Set, if wanted.
Max Clients
Set the maximum number of devices which are associated with this virtual access point.
BSSID
Show BSSID of this virtual access point.
(2 of 2)
5
Click Apply/Save to save your changes.
6
STOP. This procedure is complete.
Procedure 31-31 Displaying Station information 1
Select RGW from the top-level menu in the GPON Web-Management System window.
2
Select WLAN from the RGW menu.
3
Select Station Info from the WLAN menu. The Wireless -- Authentication Stations window appears; see Figure 31-62. Figure 31-62 Wireless -- Authentication Stations window
4
Read the Wireless -- Authentication Stations parameters. Table 31-53 describes the fields in the RGW -> WLAN -> Virtual Access Point window.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-83
31 I-240W-S and I-241W-S unit data sheet Table 31-53 Wireless -- Authentication Stations parameters Field
Description
MAC
Show the MAC of this associated device
Associated
Show that whether this associated device is associated or not currently
Authorized
Show that whether this associated device has authenticated or not
SSID
Show SSID of current associated AP for this associated device
Interface
Show interface name which indicates current associated AP for this associated device
5
Click Refresh to update the information.
6
STOP. This procedure is complete.
Supported Residential Gateway (RGW) configuration - USB device I-240W-S and I-241W-S indoor ONTs support limited configuration of RGW service including viewing and configuring USB devices using a web-based GUI.
Procedure 31-32 Configuring USB devices 1
Select RGW from the top-level menu in the GPON Web-Management System window.
2
Select USB Device from the RGW menu. The RGW -> USB Device window appears; see Figure 31-63.
31-84
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet Figure 31-63 RGW -> USB Device window
3
Configure the USB device parameters. Table 31-54 describes the fields in the RGW -> USB Device window. Table 31-54 RGW -> USB Device parameters
Field
Opinions
Storage service
Select or de-select the radio button
USB Dongle
Click on the days wanted for scheduling
Storage UserAccount Configuration
Enter hours and minutes
4
Click Add or Remove to save your changes.
5
STOP. This procedure is complete.
Supported Residential Gateway (RGW) configuration - UPnP I-240W-S and I-241W-S indoor ONTs support limited configuration of RGW service including enabling and disabling UPnP using a web-based GUI.
Procedure 31-33 Configuring UPnP 1
Select RGW from the top-level menu in the GPON Web-Management System window.
2
Select UPnP from the RGW menu.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-85
31 I-240W-S and I-241W-S unit data sheet The UPnP Configuration window appears; see Figure 31-64. Figure 31-64 UPnP Configuration window
3
Select or deselect the Enable UPnP checkbox.
4
Click Apply/Save to save your changes.
5
STOP. This procedure is complete.
Supported Residential Gateway (RGW) configuration - DLNA I-240W-S and I-241W-S indoor ONTs support limited configuration of RGW service including enabling and disabling DLNA using a web-based GUI.
Procedure 31-34 Configuring DLNA 1
Select RGW from the top-level menu in the GPON Web-Management System window.
2
Select DLNA from the RGW menu. The RGW -> DLNA window appears; see Figure 31-65.
31-86
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet Figure 31-65 RGW -> DLNA window
3
Select or deselect the Enable on-board digital media server checkbox.
4
Click Apply/Save to save your changes.
5
STOP. This procedure is complete.
Supported VoIP I-240W-S and I-241W-S indoor ONTs support limited retrieval of VoIP information using a web-based GUI. The following status information can be retrieved using a GUI:
• Hook • SIP Procedure 31-35 Hook status information retrieval 1
Select VoIP from the top-level menu in the GPON Web-Management System window.
2
Select the Hook Status option from the VoIP menu. The VoIP -> Hook Status window appears; see Figure 31-66.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-87
31 I-240W-S and I-241W-S unit data sheet Figure 31-66 VoIP -> Hook Status window
Table 31-55 describes the fields in the VoIP -> Hook Status window. Table 31-55 VoIP -> Hook Status parameters
3
Field
Options
Line ID1
On-hook or off-hook
Line ID2
On-hook or off-hook
STOP. This procedure is complete.
Procedure 31-36 SIP status information retrieval 1
Select VoIP from the top-level menu in the GPON Web-Management System window.
2
Select the SIP Status option from the VoIP menu. The VoIP -> SIP Status window appears; see Figure 31-67.
31-88
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet Figure 31-67 VoIP -> SIP Status window
Table 31-56 describes the fields in the VoIP -> SIP Status window. Table 31-56 VoIP -> SIP Status parameters
3
Field
Description
IP address
Show IP address of client
Line ID1
Show current status of Line ID1
Line ID2
Show current status of Line ID2
STOP. This procedure is complete.
Supported Diagnosis I-240W-S and I-241W-S indoor ONTs support limited testing for diagnostic information using a web-based GUI. The following tests can be performed using a GUI:
• Ping • Traceroute Procedure 31-37 Ping test 1
Select Diagnosis from the top-level menu in the GPON Web-Management System window.
2
Select the Ping Test option from the Diagnosis menu. The Diagnosis -> Ping Test window appears; see Figure 31-68.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-89
31 I-240W-S and I-241W-S unit data sheet Figure 31-68 Diagnosis -> Ping Test window
Table 31-55 describes the fields in the Diagnosis -> Ping Test window. Table 31-57 Diagnosis -> Ping Test parameters Field
Description
Destination IP Address (IPv4)
Enter the IPv4 IP address of the host to ping
Destination IP Address (IPv6)
Enter the IPv6 IP address of the host to ping
3
Enter the required information in the fields.
4
Click Apply.
5
STOP. This procedure is complete.
Procedure 31-38 Traceroute test 1
Select Diagnosis from the top-level menu in the GPON Web-Management System window.
2
Select the Traceroute Test option from the Diagnosis menu. The Diagnosis -> Traceroute Test window appears; see Figure 31-69.
31-90
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet Figure 31-69 Diagnosis -> Traceroute Test window
Table 31-58 describes the fields in the Diagnosis -> Traceroute Test window. Table 31-58 Diagnosis -> Traceroute Test parameters Field
Description
Destination IP Address (IPv4)
Enter the IPv4 IP address of the host to which you want to find a route
Destination IP Address (IPv6)
Enter the IPv6 IP address of the host to which you want to find a route
3
Enter the required information in the fields.
4
Click Apply.
5
STOP. This procedure is complete.
Supported Management I-240W-S and I-241W-S indoor ONTs support limited management using a web-based GUI. The following type of management tasks can be performed using a GUI:
• • • •
System Setting System log Update software
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-91
31 I-240W-S and I-241W-S unit data sheet
• Access control • Reboot Procedure 31-39 Configure System management 1
Select Management from the top-level menu in the GPON Web-Management System window.
2
Select the System option from the Management menu. The Management -> System window appears; see Figure 31-70. Figure 31-70 Management -> System window
3
Configure the Management -> System parameter by entering information in the field. Table 31-59 describes the field in the Management -> System window.
31-92
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet Table 31-59 Management -> System parameter
4
Field
Description
web timeout (min)
Set the timeout (in minutes) for WEB login. After a timeout, the user has to re-login.
Set the parameters for the TR-064 and TR-069 services. The TR-064 and TR-069 parameters are shown in Figure 31-71. Figure 31-71 TR-064 and TR-069 parameters window
i
Set the parameters by entering information in the fields. Table 31-60 describes the fields in the TR-064 and TR-069 section of the Management -> System window.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-93
31 I-240W-S and I-241W-S unit data sheet Table 31-60 TR-064 and TR-069 parameters Field
Description
TR-064 TR-064 username
Enter your username
TR-064 password
Enter your password
TR-069 Inform
Select the Enable radio button
Inform Interval
Set the interval duration
TR-069 ACS url
URL for the TR-069 Auto Configuration Server
TR-069 ACS username
Enter your TR-069 Auto Configuration Server username
TR-069 ACS password
Enter your TR-069 Auto Configuration Server password
Connection Request Authentication
Select the radio button
TR-069 Connection User Name
Enter your TR-069 connection username
TR-069 Connection Password
Enter your TR-069 connection password
TR-069 Connection URL
URL for the TR-069 connection
ii 5
Click Apply/Save.
Set the parameters for the NTP service. The Management -> NTP parameters are shown in Figure 31-72.
31-94
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet Figure 31-72 Management -> NTP parameters window
i
Set the parameters by entering information in the fields. Table 31-61 describes the fields in the NTP section of the Management -> System window.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-95
31 I-240W-S and I-241W-S unit data sheet Table 31-61 Management -> System parameters
ii 6
Field
Options
Automatic synchronize with Internet timer servers
Select or deselect the checkbox
First NTP timer server
Select an opinion from the drop-down menu
Second NTP timer server
Select an opinion from the drop-down menu
Third NTP timer server
Select an opinion from the drop-down menu
Fourth NTP timer server
Select an opinion from the drop-down menu
Fifth NTP timer server
Select an opinion from the drop-down menu
Timezone offset
Select an opinion from the drop-down menu
Click Apply/Save to save your changes.
STOP. This procedure is complete.
Procedure 31-40 Configure Setting management 1
Select Management from the top-level menu in the GPON Web-Management System window.
2
Select the Setting option from the Management menu. The Management -> Setting window appears; see Figure 31-73.
31-96
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet Figure 31-73 Management -> Setting window
Table 31-62 describes the fields in the Setting -> Backup section of the Management -> Setting window. Table 31-62 Setting -> Backup parameters Field
Options
Settings - Backup Backup Broadband Router configuration
Click Backup Settings
Tools -- Update Settings Setting File Name
Enter or search for a file name. Click Update Settings.
Tools Restore Default Settings Restore Broadband Router settings to the factory defaults
Click Restore Default Settings
3
Configure the parameters in the Setting -> Backup section of the Management -> Setting window.
4
Configure the TR-069 parameters in the Management -> Setting window. The TR-069 parameter is shown in Figure 31-74.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-97
31 I-240W-S and I-241W-S unit data sheet Figure 31-74 TR-069 parameter window
5
Configure the trusted CA (Certification Authority) for TR-069 management by clicking Import Certificate.
6
STOP. This procedure is complete.
Procedure 31-41 Configure System log 1
Select Management from the top-level menu in the GPON Web-Management System window.
2
Select the System Log option from the Management menu. The Management -> System Log window appears; see Figure 31-75.
31-98
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet Figure 31-75 Management -> System Log window
3
Click either View System Log or Configure System Log.
4
STOP. This procedure is complete.
Procedure 31-42 Update Software 1
Select Management from the top-level menu in the GPON Web-Management System window.
2
Select the Update SW option from the Management menu. The Management -> Update SW window appears; see Figure 31-76.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-99
31 I-240W-S and I-241W-S unit data sheet Figure 31-76 Management -> Update SW window
3
Enter or search for a software file name.
4
Click Update Software.
5
STOP. This procedure is complete.
Procedure 31-43 Configure Access control 1
Select Management from the top-level menu in the GPON Web-Management System window.
2
Select the Access Control option from the Management menu. The Management -> Access Control window appears; see Figure 31-77.
31-100
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet Figure 31-77 Management -> Access Control window
Table 31-63 describes the fields in the Management -> Access Control window. Table 31-63 Management -> Access Control parameters Field
Description
User Name
Enter the user name to change the password. The user name should be either "admin", "tech", or "user".
Old Password
Enter current password of the user
New Password
Enter the new password with which you want to the replace the current password
Confirm Password
Enter the new password again
3
Enter user name and password inform.
4
Click Apply/Save.
5
Configure the temp WAN parameters in the Management -> Access Control window. The Management -> temp WAN parameter is shown in Figure 31-78.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-101
31 I-240W-S and I-241W-S unit data sheet Figure 31-78 temp WAN parameter window
6
Select or deselect Temporary WAN connection.
7
STOP. This procedure is complete.
Procedure 31-44 Reboot 1
Select Management from the top-level menu in the GPON Web-Management System window.
2
Select the Reboot option from the Management menu. The Management -> Reboot window appears; see Figure 31-79.
31-102
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
31 I-240W-S and I-241W-S unit data sheet Figure 31-79 Management -> Reboot window
3
Click Reboot.
4
STOP. This procedure is complete.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
31-103
31 I-240W-S and I-241W-S unit data sheet
31-104
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
NTP 172 Install an I-240W-S or I-241W-S indoor ONT Purpose This NTP provides the steps to install an I-240W-S or I-241W-S indoor ONT.
General The DLPs listed in this NTP describe mounting and cabling for I-240W-S or I-241W-S indoor ONTs.
Prerequisites See the listed DLPs for prerequisites.
Recommended tools You need the following tools for the installation:
• • • • • • • •
#2 Phillips screwdriver 1/4 in. (6 mm) flat blade screwdriver wire strippers fiber optic splicing tools RJ-45 cable plug crimp tool voltmeter or multimeter optical power meter drill and drill bits
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
NTP 172-1
NTP 172 Install an I-240W-S or I-241W-S indoor ONT
Safety information Read the following safety information before installing the unit.
Danger 1 Contact the local utility company before you connect the enclosure to the utilities. Danger 2 Observe the local and national laws and regulations that may be applicable to this installation. Warning This equipment is ESD sensitive. Proper ESD protections should be used when removing the fiber access cover of the indoor ONT.
Caution Keep indoor ONTs out of direct sunlight. Prolonged exposure to direct sunlight can damage the unit.
Note Observe the following:
•
• • •
The indoor ONT should be installed in accordance with the applicable requirements of the NEC or CEC. Local authorities and practices take precedent when there is conflict between the local standard and the NEC or CEC. The indoor ONT must be installed by qualified service personnel. Indoor ONTs must be installed with cables that are suitably rated and listed for indoor use. See the detailed specifications in the I-240W-S and I-241W-S unit data sheet for the temperature ranges for these ONTs.
Procedure Use this procedure to install an I-240W-S or I-241W-S indoor ONT. 1
Prepare the cables at the site where the ONT will be installed (DLP 100).
2
Are any of the cables missing? a
If yes, go to step 3.
b
If no, go to step 4.
3
Locate each missing cable and route them to the ONT as per local practices.
4
Place the indoor ONT unit: a
NTP 172-2
On the flat surface, such as a desk. i
Wrap the excess optic cable inside the fiber storage tray.
ii
Attach the fiber storage tray to the ONT.
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
NTP 172 Install an I-240W-S or I-241W-S indoor ONT
b 5
iii
Place the ONT on the flat surface, horizontally resting on its four feet.
iv
Go to step 5.
On a wall (DLP 122).
Review the connection locations as shown in Figures NTP 172-1 and NTP 172-2. Figure NTP 172-1: I-240W-S indoor ONT connections
I O
USB ports
Wi-Fi Reset POTS Protected button ports Service button (RJ-11)
Ethernet ports (RJ-45)
Fiber Power Power optic connector on/off connector switch 22435
Figure NTP 172-2: I-241W-S indoor ONT connections
Reset button
Wi-Fi POTS Protected ports Service button (RJ-11)
Ethernet ports (RJ-45)
Fiber Power optic connector connector
F-type Power on/off coaxial switch connector 22788
See Figures NTP 172-3 and NTP 172-4 for the location of the USB ports on the I-240W-S and I-241W-S indoor ONTs.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
NTP 172-3
NTP 172 Install an I-240W-S or I-241W-S indoor ONT Figure NTP 172-3: I-240W-S indoor ONT connections (USB host port)
Internet/ USB host port
I O
22442
Figure NTP 172-4: I-241W-S indoor ONT connections (USB host port)
USB port 22788
6
Connect the Ethernet cables to the RJ-45 ports (DLP 101).
7
Connect the POTS cables to the RJ-11 ports (DLP 123).
8
For the I-241W-S indoor ONT only, connect the coaxial cable to the F-Type connector (DLP 116).
9
Connect the SC/APC fiber optic cable (DLP 125).
Warning Be careful to maintain a bend radius of no less than 1.5 inches (3.8 cm) when connecting the fiber optic cable. Too small of a bend radius in the cable can result in damage to the optic fiber.
NTP 172-4
10
Install the power supply according to manufacturer specifications.
11
Connect the power cable with an 8-pin Molex connector to the power supply.
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
NTP 172 Install an I-240W-S or I-241W-S indoor ONT 12
Connect the power cable with an 8-pin Molex connector to the ONT unit.
Warning To avoid the possibility of damage to the pins on the power cable connector, carefully align the pins on the connector on the cable with the pin holes in the power connector on the ONT before making the connection. Figure NTP 172-5: Molex 8-pin connector Pin 2
Pin 8
Pin 1
Pin 3
Pin 7 20179
Note Observe the following:
•
Only Pins 1, 2, and 7 in the Molex connector pin arrangement shown in Figure NTP 172-5 are used with I-240W-S and I-241W-S indoor ONTs.
13
Power up the ONT unit by using the on/off power switch.
14
If used, enable the Wi-Fi service, as described in Web-based ONT configuration.
15
Verify the ONT LEDs, voltage status, and optical signal levels (DLP 127).
16
Activate and test the services (DLP 128).
17
If used, configure the SLID (DLP 129).
18
If necessary, reset the ONT (DLP 126).
19
STOP. This procedure is complete.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
NTP 172-5
NTP 172 Install an I-240W-S or I-241W-S indoor ONT
NTP 172-6
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
NTP 173 Replace an I-240W-S or I-241W-S indoor ONT Purpose This NTP provides the steps to replace an I-240W-S or I-241W-S indoor ONT.
General The DLPs listed in this NTP describe mounting and cabling for I-240W-S or I-241W-S indoor ONTs.
Prerequisites See the listed DLPs for prerequisites.
Recommended tools You need the following tools for replacing the ONT:
• • • • • • • •
#2 Phillips screwdriver 1/4 in. (6 mm) flat blade screwdriver wire strippers fiber optic splicing tools RJ-45 cable plug crimp tool voltmeter or multimeter optical power meter drill and drill bits
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
NTP 173-1
NTP 173 Replace an I-240W-S or I-241W-S indoor ONT
Safety information Read the following safety information before replacing the unit.
Danger 1 Contact the local utility company before you connect the enclosure to the utilities. Danger 2 Observe the local and national laws and regulations that may be applicable to this installation. Warning This equipment is ESD sensitive. Proper ESD protections should be used when removing the fiber access cover of the indoor ONT.
Caution Keep indoor ONTs out of direct sunlight. Prolonged exposure to direct sunlight can damage the unit.
Note Observe the following:
•
• • •
The indoor ONT should be installed in accordance with the applicable requirements of the NEC or CEC. Local authorities and practices take precedent when there is conflict between the local standard and the NEC or CEC. The indoor ONT must be installed by qualified service personnel. Indoor ONTs must be installed with cables that are suitably rated and listed for indoor use. See the detailed specifications in the I-240W-S and I-241W-S unit data sheet for the ONT temperature ranges for these ONTs.
Procedure Use this procedure to replace an I-240W-S or I-241W-S indoor ONT.
NTP 173-2
1
Deactivate the ONT services (DLP 131). If you are using the SLID feature, this step is not required. The ONT and the services can remain in service (IS).
2
If used, disable the Wi-Fi service, as described in Web-based ONT configuration.
3
Power down the unit by using the on/off power switch; see Figures NTP 173-1 and NTP 173-2 for the location of the power button on I-240W-S and I-241W-S ONTs.
4
Disconnect the POTS, Ethernet and power and coaxial cables (DLP 132) as well as fiber optic cables (DLP 133) from the ONT; see Figures NTP 173-1 and NTP 173-2 for the connector locations on I-240W-S and I-241W-S indoor ONTs.
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
NTP 173 Replace an I-240W-S or I-241W-S indoor ONT Figure NTP 173-1: I-240W-S ONT connections
I O
USB ports
Wi-Fi Reset POTS Protected button ports Service button (RJ-11)
Ethernet ports (RJ-45)
Fiber Power Power optic connector on/off connector switch 22435
Figure NTP 173-2: I-241W-S ONT connections
Reset button
POTS Wi-Fi ports Protected Service button (RJ-11)
Ethernet ports (RJ-45)
Power Fiber optic connector connector
Power F-type coaxial on/off switch connector 22788
See Figures NTP 173-3 and NTP 173-4 for the locations of the USB ports on I-240W-S and I-241W-S indoor ONTs.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
NTP 173-3
NTP 173 Replace an I-240W-S or I-241W-S indoor ONT Figure NTP 173-3: I-240W-S indoor ONT connections (USB host port)
Internet/ USB host port
I O
22442
Figure NTP 173-4: I-241W-S indoor ONT connections (USB host port)
USB port 22788
5
NTP 173-4
Replace the ONT with a new unit: a
On a flat surface, such as a desk, substitute a replacement ONT for the old ONT; go to step 6.
b
On a wall. i
Slide the old ONT off of the mounting screws until the ONT is free of the wall.
ii
Slide the wall mount holes on the ONT enclosure or fiber storage tray of the new ONT over the mounting screws until it is securely seated.
6
Connect the Ethernet cables to the RJ-45 ports (DLP 101).
7
Connect the POTS cables to the RJ-11 ports (DLP 123).
8
For the I-241W-S indoor ONT only, connect the coaxial cable to the F-Type connector (DLP 116).
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
NTP 173 Replace an I-240W-S or I-241W-S indoor ONT 9
If required, have approved service personnel who are trained to work with optic fiber clean the fiber optic connection. See DLP 134 for more information about fiber optic handling, inspection, and cleaning.
Danger Fiber optic cables transmit invisible laser light. To avoid eye damage or blindness, never look directly into fibers, connectors, or adapters. 10
Connect the SC/APC fiber optic cable (DLP 125).
Warning Be careful to maintain a bend radius of no less than 1.5 inches (3.8 cm) when connecting the fiber optic cable. Too small of a bend radius in the cable can result in damage to the optic fiber. 11
Install the power supply according to manufacturer specifications.
12
Connect the power cable with an 8-pin Molex connector to the power supply.
13
Connect the power cable with an 8-pin Molex connector to the ONT unit.
Warning To avoid the possibility of damage to the pins on the power cable connector, carefully align the pins on the connector on the cable with the pin holes in the power connector on the ONT before making the connection. Figure NTP 173-5: Molex 8-pin connector Pin 2
Pin 8
Pin 1
Pin 3
Pin 7 20179
Note Observe the following:
•
Only Pins 1, 2, and 7 in the Molex connector arrangement shown in Figure NTP 173-5 are used with the I-240W-S and I-241W-S indoor ONT.
14
Power up the unit by using the on/off power switch.
15
If used, enable the Wi-Fi service, as described in Web-based ONT configuration.
16
If used, configure the SLID (DLP 6).
Note A new SLID or the old SLID may be used with the replacement ONT. If a new SLID is used, the new SLID must also be programmed at the P-OLT using TL1 or a network manager. If the old SLID is used, no changes need to be made at the P-OLT; see the operations and maintenance documentation for the OLT for more details.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
NTP 173-5
NTP 173 Replace an I-240W-S or I-241W-S indoor ONT
NTP 173-6
17
Verify the ONT LEDs, voltage status, and optical signal levels (DLP 127).
18
Activate and test the services (DLP 128).
19
If necessary, reset the ONT (DLP 126).
20
STOP. This procedure is complete.
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
NTP 174 Configure an I-240W-S or I-241W-S ONT General Please refer to the OLT Operations and Maintenance using TL1 and CLI guide for the software configuration procedure for I-240W-S and I-241W-S indoor ONTs. For HTTP configuration procedures, please refer to chapter 6, ONT management using an ONT interface.
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a 3FE 55052 AAAA TCZZA Edition 01 ONT Product Information Guide
August 2012
NTP 174-1
NTP 174 Configure an I-240W-S or I-241W-S ONT
NTP 174-2
August 2012
Alcatel-Lucent 7360 ISAM FX, 7330 ISAM FTTN, 7302 ISAM ONT R04.04.02a Edition 01 3FE 55052 AAAA TCZZA ONT Product Information Guide
View more...
Comments
