Machine Design and Shop Practice Problems
Short Description
Practice solving...
Description
MACHINE DESIGN AND SHOP PRACTICE PROBLEMS ELEMENTS (with answers and solutions)
1.
What is the polar section modulus of a solid shaft with a diameter of 101.6 mm? 3 4 3 a) 209.5 cm b) 209.5 cm c) 205.9 cm Answer: c) 205.9 cm Solution:
2.
3
J
2J
c
D
Z j
4
d) 205.9 cm
16
D3
16
10.163 205.9 cm3
With the water interruptions prevailing in your town, you have been asked to design an upright cylindrical water tank 6 meters in diameter and 6 meters high, vented, and to be filled completely with water. Determine the minimum thickness of the tank plate if the stress is limited to 40 Mpa. a) 3.3 mm b) 4.4 mm c) 5.5 mm d) 8.8 mm Answer: b) Thickness, t = 4.4 mm Solution: p gh 1000 9.8066 6 58 839.6 Pa 58.8396 kPa
t 3.
pD 2s t
58.8396 6 0.00441 m 4.41 mm 2 40 000
A steel shaft 1.75 inches in diameter transmits 40 Hp at 1800 rpm. Assuming a modulus of rigidity of 12 x 10 psi, find the torsional deflection of the shaft i n degrees per foot length. a) 0.0073 b) 0.0037 c) 0.0063 d) 0.00013
Solution: 4.
L
T JG
32T
D 4 G
6
63 000 Hp 6300040 32 n 1800 0.00013 radian 0.0073 D4 G 1.754 12 x 106
32
A helical-coil spring has a mean coil diameter of 1 inch and a wire diameter of 1/8 inch. Determine the curve correction factor of the spring. a) 1.144 b) 1.44 c) 1.1144 d) 1.1414 Answer: Curve Correction Factor, K c = 1.1144 4C 1 Solution: K c
5.
K w K s
4C 4
0.615
2C 1
C
1.184 1.0625
1.1144
2C A vise is equipped with a 1-inch single square thread, with 4 threads per inch. The frictional radius of the collar is 0.5 inch. The coefficient of friction for both the collar and threads is 0.20. How much external torque must be applied to produce a force of 200 lb against the jaws of the vise? a) 39.73 in-lb b) 33.97 in-lb c) 37.93 in-lb d) 39.37 in-lb Answer: c) 37.93 in-lb Vise Jaw Screw Collar F = 200 lb
Nut Handle
Solution: For the thread pitch, p
1
1
Numb Nu mber er of Thread Threadss per Inch Inch
inch 0.25 inch 4
For the minor diameter, D i = Do – p p = 1 – 1 – 0.25 0.25 = 0.75 inch For the mean or pitch diameter of the screw, Dm
Do
Di 2
1 0.75 2
0.875 inch
For the lead angle,
L tan tan Dm 1
1
p 0.25 tan tan 0.875 Dm 1
1
0.0909 09095 5 5.197 197
o
Solving for the torque required to overcome the collar friction,
Tc
fFDc 2
0.2 200 0.5 2
20 in lb
Solving for the torque required to overcome the thread friction,
Ts
FDm 2
875 0.0909 09095 5 0 .2 tan f 2000.875 25.93 in lb 1 f tan . . 2 1 0 2 0 9 0 9 5
Solving for the total torque, T = T s + Tc = 25.93 + 20 = 45.93 inches 6.
ans.
A helical-coil spring has a mean coil diameter of 1 inch and a wire diameter of 1/8 inch. Determine the Wahl factor of the spring. a) 1.148 b) 1.184 c) 1.418 d) 1.814 Answer: b) Wahl Factor, K w = 1.184 Solution: C
7.
Dm d
1 1 8
8
K w
4C 1 4C 4
0.615 C
48 1 48 8
0.615 8
1.184
A helical-coil spring has a mean coil diameter of 1 inch and a wire diameter of 1/8 inch. Determine the value of Bergstrassar factor of the spring. a) 1.172 b) 1.712 c) 1.217 d) 1.271 Answer: a) Bergstrassar Factor, K B = 1.1724 4C 2 48 2 1 K B 1.1724 8 1 4C 3 48 3 d 8 o Compute the tooth thickness of a 14.5 spur gear with diametral pitch of 5. a) 0.23140 inch b) 0.31416 inch c) 0.43140 inch
Solution: C 8.
Dm
d) 0.03140 inch
Answer: b) Tooth thickness, t = 0.31416 inch Solution: t 9.
1.5708 p d
1.5708 5
0.31416 inch
Compute the speed of the gear mounted on a 52.5 mm diameter shaft receiving power from a driving motor with 250 Hp. a) 2 182 rpm b) 2 071 rpm c) 2 265 rpm d) 2 341 rpm Answer: c) The speed, N = 2265 rpm Solution: From PSME Code: N
80 P D
3
80 250
52.5 25.4
rpm 2 264.92 rpm
3
10. Compute the working strength of 1 inch bolt which is screwed up tightly in packed joint when the allowable working stress is 13000 psi. a) 3 600 lb b) 3 950 lb c) 3 900 lb d) 3 800 lb Answer c) The working strength, W = 3 900 lb Solution:
From
W s t 0.55d 2
machinery’s
0.25d 13 000 0.5512 0.251 3 900 lb
Handbook,
page
1149:
11. Compute the nominal shear stress at the surface, in MPa, for a 50 mm diameter shaft that is subjected to a torque of 0.48 kN-m. a) 16.95 b) 21.65 c) 19.56 d) 25.12 Answer: Shear Stress, ss = 19.56 MPa Solution: ss
16 T
D
3
16 0.48
0.0503
19 556.96 kPa kP a 19.56 MPa
12. A hollow iron pipe to be designed as a column has an outside diameter of 240 mm and is subjected to a force of 80 KN. Find the pipe thickness if the compressive stress is limited to 16 MPa. a. 5.85 mm b. 6.85 mm c. 7.85 mm d. 8.85 mm Answer: b) Pipe thickness, t = 6.85 mm
Solution: Inside Diameter, D i
2
Do
Thickness of the Pipe, t
4F
s
Do
0.242
Di 2
4 80
16 000
240 226.3 2
0.2263m 226.3 mm
6.85 mm
13. A uniform beam 12 meters long is fixed at one end. It has a uniform weight of 50 kg/m along its length. A load of 20 kgs. is suspended on the beam 4 m from the free end. The moment at the fixed end is a. 3760 kg-m b. 0.0 kg-m c. 60 kg-m d. 4800 kg-m Answer: a) 3760 kg-m
W = 50 (12) = 600 kg F = 20 kgs
Solution: Bending Moment,
M 6 600 8 20 3 760 kg m 6m 8m
14. A 20o straight-tooth bevel pinion having 14 teeth and a diametral pitch of 6 teeth/inch drives a 42-tooth gear. The two shafts are at right angles and in the same plane. Find the pitch angle of the pinion. a) 18.4o b) 20o c) 14.5o d) 20.5o Answer: a) Pitch angle of the pinion = 18.4
Solution:
o
T p 14 tan 1 tan 1 18.4 o 42 Tg
o
15. A 20 straight-tooth bevel pinion having 14 teeth and a diametral pitch of 6 teeth/inch drives a 32-tooth gear. The two shafts are at right angles and in the same plane. The pinion is to transmit 1800 rpm and transmitting 50 hp. Determine the pitch diameters of the gears. a) 2.33 inches and 5.36 inches b) 3.23 inches and 3.56 inches c) 5.36 inches and 6.36 inches d) 2.33 inches and 2.33 inches Answer: a) 2.33 inches and 5.36 inches
Solution: D1
T1 Pd
14
2.33 inches
6
D2
T 32 D1 2 2.33 5.36 inches 14 T1
16. A 1-inch diameter shaft has a single disc weighing 75 lb mounted midw ay between two bearings 20” apart. Find the lowest critical speed in rpm. Neglect the weight of the shaft. Assume that the modulus of elasticity is 30 x 106 psi. a) 2038 rpm b) 2308 rpm c) 2380 rpm d) 2803 rpm W = 75 lb
Solution: D = 1 inch
6
E = 30 x 10 psi
Moment of Inertia, I
D4 64
1
L = 20 inches
30 cr
10”
0.0491 in.
4
64
Solving for the lowest critical speed,
Ncr
10”
4
576EIg
cr
W L3
30 213.39
576 30 x 106 0.04 0.0491 91 32.2 32.2 576 3
75 20
213.39 9 rad/ s 213.3
037.68 rpm rpm 2 037.68
17. A flywheel weighing 457 kg has a radius of 375 mm. How much energy, in N-m, does the flywheel loss from 3 rps to 2.8 rps? a) 368 b) 150 c) 1474 d) 38 Answer: c) Flywheel Energy =1474 Solution: V1
2 0.375 3 7.069 m / s KE
2
m V1
V22
V2 2
457 7.069
6.5972
2 0.3752.8 6.597 m / s
1 473.91 N m 2 2 18. A triple threaded worm has a pitch diameter of 3 inches. The wheel has 25 teeth and a pitch diameter of 5 inches. Material for both the wheel and the wheel is phosphor bronze. Determine the helix angle of the gear. a) 11.31o b) 13.11o c) 11.13o d) o 10.13
Answer: Gear Helix angle = 11.31 o
Solution: Circular pitch of the worm worm gear, Pc
Dg Tg
5 25
0.6283 inch
Where, Pc = Pa = pitch of the worm Solving for the lead, L = N t Pa = 3(0.6283) = 1.8849 inches
Solving for the lead angle of the worm,
L 1 1.8849 tan 1 11.31o tan 3 Dw
For the helix angle, and considering that the shafts angle is 90 o, o
g = = 11.31 ans. 19. A single square thread power screw is to raise a load of 70 kN. The screw has a major diameter of 36 mm and a pitch of 6 mm. The coefficient of thread friction and collar friction are 0.13 and 0.10 respectively. If the collar mean diameter is 90 mm and the screw turns at 60 rpm, find the axial linear speed of the screw. a) 5 mm/s b) 6 mm/s c) 7 mm/s d) 5.5 mm/s Answer: b) 6 mm/s Solution: For the linear speed of the screw, V n = n (L) = (60 rpm)(6 mm/rev) = 360 mm/min = 6 mm/s 20. A double thread ACME screw driven by a motor at 400 rpm raises the attached load of 900 kg at a speed of 10 m/min. The screw has a pitch diameter of 36 mm; the coefficient of friction on threads is 0.15. The friction torque on the thrust bearing of the motor is taken as 20 % of the total input. Determine the lead angle. o o o o a) 12.465 b) 14.265 c) 15.462 d) 16.452 Answer: a) 12.465 o Solution: For the lead, L For the lead angle,
V n
10 400
0.025 m 25 mm
L 25 tan 1 tan 1 12.465o D 36 m
21. What Hp can a 1-inch diameter short shaft transmit at 380 rpm? a) 3 Hp b) 18 Hp c) 10 Hp
d) 7.1 Hp
Answer: c) 10 Hp Solution: P
D3 N 38
13 380 38
10 Hp
22. A spur pinion rotates at 600 rpm and transmits 25 kW to a mating gear. The pitch diameter of the pinion is 100 mm, and the pressure angle is 20 o. Determine the tangential load, in N. a) 7660 b) 6790 c) 3900 d) 3098
Solution: Ft
2 30 P 2 30 25 000 7 957.75 N D n 0.10 600
23. A multiple-disk clutch, composed of three plates with a small diameter of 150 mm and large diameter of 200 mm, is designed to transmit 100 kW at 3000 rpm at a coefficient of friction of 0.5. Determine the spring force needed to engage the clutch. a) 2820 N b) 2428 N c) 5460 N d) 3638 N Answer: 3638 N Solution:
T
30 P
n
T f P r f N fs
30 100
0.3183 kN m 318.3 N m 3000 D d f P N fs 4 P
4T f D d N fs
4 318 300 0.5 200 150 2
3 637.71 N
24. A wire rope lifts a load of 10 kips at a maximum speed of 1000 feet per minute, attained in 5 seconds starting from rest. The rope has a metallic cross sectional area of 0.4 in 2. Determine the maximum tensile stress on the rope in ksi. a) 26.2 b) 25.0 c) 27.6 d) 32.4 Answer: c) maximum tensile stress = 27.6 MPa Solution: a
V1
Vo t
1000 / 60 0
St
5
11,034.16 0.4
3.33 fps 2
F WL 1
a
3.33 10 000 1 11034.16 g 32.2
lb
27 585.4 psi 27.6 ksi
25. What is the bursting steam pressure of a hemispherical steel shell with a diameter of 100 inches and made of 0.0635-m thick steel plate, if the joint efficiency is 70 % and the tensile strength is 60 000 psi? a) 4 020 psi b) 4 200 psi c) 2 400 psi d) 2 040 psi Answer: b) 4200 psi
63.5 2 in 60 000 lb / in 0.70 4 t s l E j 25 . 4 4 200 psi p 4
Solution:
D
100 in.
Where, p = bursting pressure, psi t = shell thickness, inches
sl = shell stress, psi D = shell diameter, inches
E j
=
joint
efficiency Note: For the longitudinal stress of the thin -walled cylinder, and the stress for spherical tank: s L
p D 4 t E j
26. A cylinder having an internal diameter if 508 mm and external diameter if 914.4 mm is subjected to an internal pressure of 69 MPa and an external pr essure of 14 MPa. Determine the hoop stress at t he inner surface of the cylinder. a) 90.11 MPa b) 91.10 MPa c) 911.0 MPa d) 19.10 Mpa Answer: a) 90.11 MPaa
Solution:
s ti
2
p i r o
r i2 2 p o r o2 r o2 r i2
69 MPa
914.4
2
2
914.4 214 MPa 2 2 2 508 mm mm 2
508 2
mm
914.4 2
2
mm
2
mm
sti = 90.11 Mpa Where, sti = maximum tangential or hoop stress at the inside pi = internal pressure, Mpa po = external pressure, Mpa
r i = inside radius, mm r o = outside radius, mm 2
Note: For the maximum tangential or hoop stress at the outside, s to
2 p i r i
p o r o2 r i2 2 2 r o r i
27. What length of a square key is required for a 4-in diameter shaft transmitting 1000 hp at 1000 rpm? The allowable shear and compressive stresses in the key are 15 ksi and 30 ksi, respectively. a) 2.1 inches b) 2.8 inches c) 3.2 inches d) 4.2 inches Answer: a) 2.1 inches Solution: Transmitted torque, T Key width, b
D 4
63000Hp n
630001000 1000
63000
in lb
, for good proport propo rtion ion
Key length based on shear, L
2T ss bD bD
Key length based on compression, L
2 63000 15 00014 4T
sc t D
2 .1 inches
4 63000 30 0001 4
2.1
Therefore, use L = 2.1 inches 28. The root diameter of a double square thread is 0.55 inch. The screw has a pitch of 0.2 inch. Find the number of thread per inch. a) 0.2 threads/inch b) 10 threads/inch c) 5 threads/inch d) 2.5 threads/inch Answer: TPI = 5 threads per inch Solution: The number of threads per inch, TPI TP I
1 p
1 0.2
5
threads / inch
29. A single square thread power screw is to raise a load of 70 kN. The screw has a major diameter of 36 mm and a pitch of 6 mm. The coefficient of thread friction and collar friction are 0.13 and 0.10 respectively. If the collar mean diameter is 90 mm and the screw turns at 60 rpm, find the combined efficiency of the screw and collar. a) 15.32 % b) 12.53 % c) 13.52 % d) 15.97 % Answer: b) 12.53 % W = 70 N
p
1 1 p 6 3 mm 2 2
Solution: For the depth of the thread, h
For the mean diameter of the screw, D m
For the lead angle,
D o h 36 3 33 mm
L p tan 1 tan 1 6 3.3123 o tan 1 33 D m D m tan 1 f tan 100 %
Solving for the Efficiency, e
f c D c 1 f tan D m
tan f
tan 3.3125 1 0.13 tan 3.3125 100 % 12.53 % e 0.10 90 1 0.13 tan 3.3125 tan 3.3125 0.10 33 o
o
o
o
30. Determine the power capacity of a cone clutch under uniform pressure and assuming the following conditions: major diameter = 250 mm; minor diameter = 200 mm; length of conical elements in contact = 125 mm; rotational speed = 870 rpm; coefficient of friction = 0.30; and allowable pressure = 70 kPa. a) 25.74 Hp b) 24.75 Hp c) 27.45 Hp d) 24.57 Hp Answer: a) 25.74 Hp 2 r o
r i3 2 1253 1003 r f 112.96 r 2 r 2 3 3 1252 1002 o i 3
Solution:
Friction radius,
Surface Area of contact, A f
2r f b 20.112960.125 0.0887
Force normal to the surface of contact, Fn
P
mm
m2
pA f 700.0887 6.209 kN
Power Capacity, n Tf n 870 f Fn r f 0.306.2090.11296 19.2 kW 25.74 Hp 30 30 30
31. Three extension springs are hooked in series that support a single weight of 100 kg. The first spring is rated at 4 kN/m and the other two springs are rated 6 kN/m each. Determine the equivalent stiffness of the three springs. a) 1.71 kN/m b) 5 kN/m c) 2.71 kN/m d) 3.71 kN/m Answer: a) 1.71 kN/m Solution:
1 k e
1 k 1
1 k 2
1 k 3
1
1
1
1
1
3 4
4
6
6
4
3
12
7 12
k e
12 7
1.71 kN / m
32. A flat belt is 6 inches wide and 1/3 inch thick and transmits 20 Hp. The center distance is 8 ft. The driving pulley is 6 inches i n diameter and rotates at 2 000 rpm such that the loose side of the belt is on top. The driven pulley is 18 inches in diameter. The belt material is 0.035 lb/in3 and the coefficient of friction is 0.30. Determine the belt net tension. a) 201 lb b) 210 lb c) 102 lb d) 120 lb
Answer: b) 210 lb
Solution:
F F1 F2
Other Solution:
Vm
2T D
2 63 00020 210 lb 6 2 000
2 63 000 Hp
D
n
6 D n 2 000 3141.59 fpm 12
F F1 F2
33 000 Hp Vm
33 00020 3141.59
210 lb
33. A pulley 600 mm in diameter transmits 40 kW at 500 rpm. The arc of contact between the belt and pulley is 155o, the coefficient of friction between belt and pulley is 0.35 and the safe working stress of the belt is 2.1 MPa. Determine the belt tensions ratio, neglecting the effect of centrifugal force. a) 2.578 b) 2.857 c) 5.287 d) 5.782 Solution:
F1
e f e0.35155 180 2.578
F2
Answer: a) 2.578 34. Select a deep-groove ball bearing to carry a radial load F x = 800 lb and a thrust load F z = 700 lb at 1750 rpm. The service is 8 hr/day, but it is not continuous; design for 20 000 hr. The operation is smooth with little vibration; the outer ring rotates. Determine the design life in mr with no more than 10 % failure. a) 20100 mr b) 2100 mr c) 2001 mr d) 1200 mr Answer: b) 2100 mr Solution: B10
Hrs 60 min s / hr rpm rpm Hrs
20 000 60 1 750 10
6
2100
mr
35. Determine the Hp lost when a collar is loaded with 2000 lb, rotates at 50 rpm, and has a coefficient of friction of 0.15. The outside diameter of the collar is 4 inches and the inside diameter is 2 inches. a) 0.7314 Hp b) 0.3714 Hp c) 0.4713 Hp d) 0.4371 Hp Answer: b) 0.3714 Hp Solution: fHp
Tf n 63000
f W r f n 63000
0.152000 lb1.56 inches 50 rpm rpm 63000
0.3714
2 r o
r i3 2 23 13 r f r 2 r 2 3 32 12 1.56 inches 3 o i 3
Where,
36. What load in N must be applied to a 25 mm round steel bar 2.5 m long (E = 207 Gpa) to stretch the bar 1.3 mm? a) 42 000 N b) 52 840 N c) 53 000 N d) 60 000 N Answer: b) The load, 52 840 N Solution: The load, F
AE L
1.3 2 2 D E 4 0.025 207 000 000 000 52 837.66 L 4 2 . 5 1000
N
37. A 50-mm diameter shaft is to transmit 12 kW power at a speed of 500 rpm, determine the mean diameter of the pin, under double shear, for a material having a safe unit stress of 40 N/ mm2.
a) 11.08 mm
b) 12.08 mm
c) 13.08 mm
d) 10.08 mm Shaft
Answer: b) Diameter of the pin = 12.08 mm Solution:
30 P
Transmitted Torque, T Pin Shearing Force, Fs
Pin Mean Diameter, ss
n 2T D Fs
2 As
30 12 000
500
2 229183
2 Fs
d
50 4 Fs 2d
9167.32 N 2 Fs
d2
2 9 167.32
ss
2
229.183 N m 229183 N mm
40
12.08 mm
38. A 1200 mm cast iron pulley is fastened to 112.5 mm shaft by means of a 28.13 mm square key 175 mm long. The key and shaft have a shearing stress of 14 000 psi. Determine the force acting at the pulley that will shear the key. a) 10 015 lb b) 11 005 lb c) 11 050 lb d) 10 501 lb Answer: a) The force acting on the pulley = 10 015 lb
s s bLD D 2 2T 28.13 175 112.5 14 000 10 014.74 lb s s bL F p D p D p D p 25 . 4 25 . 4 1 200 2
Solution:
Where, T
s s bLD 2
based Torque based
on shear , in lb
39. A 75-mm diameter shaft is transmitting 350 kW at 650 rpm. A flange coupling is used and has 6 bolts, each 18 mm in diameter. Find the required diameter of the bolts circle based on an average shearing stress of 27.5 MPa. a) 245 mm b) 254 mm c) 452 mm d) 425 mm Answer: a) Bolt Circle diameter = 245 mm Solution: D B
8T
ss d
Note:
2
nB
830P
2
2
d ssn n B
830350
2 0.0182 27 5006506
Torque Based on Shear, T
ssd 2DBn n B 8
0.245 m 245 mm
30 P
n
40. If a sleeve bearing has an outside diameter of 38.1 mm and a length of 50.8 mm, the wall thickness is 3/16 inch. The bearing is subjected to a radial load of 500 kg. What is the bearing pressure, in psi? a) 904 psi b) 409 psi c) 490 psi d) 940 psi Answer: c) Bearing pressure = 490 psi Solution:
For bearing or projected area, A B
Bearing pressure, p
W AB
50.8 38.1 2 LD in. in. 23 in 2.25 in 16 25.4 25.4
500 kg2.205 lb / kg 2.25 in
2
490 psi
Pin T
41. Determine the minimum whole depth of spur gear of 14.5 o involute type with diametral pitch of 24 and circular pitch of 0.1309 inch. a) 0.09000 inch b) 0.08900 inch c) 0.0899 inch d) 0.089758 inch Answer: c) Whole depth = 0.0899 inch Solution: From Vallance, page 262: h
2.157 p d
2.157 24
0.089875 inch
42. A parallel helical gear set was a 17-tooth pinion driving a 34-tooth gear. The pinion has a right-hand helix angle of 30o, a normal pressure angle of 20 o, and a normal diametral pitch of 5 teeth/in. Find the axial circular pitches. a) 1.2566 inches/tooth b) 1.6625 inches/tooth c) 1.6526 inches/tooth d) 1.6256 inches/tooth Answer: a) Axial circular pitch = 1.2566 inches/tooth Solution: Pc
Pcn cos
0.62832
Pc
cos 30 30o
inch / tooth
0.72552
tooth 1.2566 inches / to tan tan 30 30o 43. Determine the Poisson’s ratio of a material whose modulus of elasticity is 200 GPa and whose modulus of rigidity is 80 GPa. a) 0.33 b) 0.25 c) 0.38 d) 0.22 Pa
0.72552
Answer: b) Poisson’s ratio = 0.25 Solution: G
E
E = 200GPa,
2(1 )
0.25
G = 80GPa:
44. A steel has a BHN = 300. What is its approximate ultimate strength in ksi? a) 300 ksi b) 150 ksi c) 75 ksi
d) 200 ksi
Answer: b) Ultimate Strength = 150 ksi Solution: Su 0.5(BHN), ksi 45. If the angular deformation of a solid shaft should not to exceed 1 o in a length of 1.8 m and the allowable shearing stress is 83 MMa, what is the diameter of the shaft? Assume that the shaft material has G = 77 x 10 6 kPa. a) 222.34 mm b) 234.22 mm c) 23.42 cm d) 24.22 cm Answer: a) Shaft diameter = 222.34 mm
D3ss L 16 4 D G
32
Solution:
TL JG
32T L
D
4
G
2 ss L DG
D
2 ss L
G
2830001.8
o 77 x 106 180
o
1
222.34 mm
46. Determine the Hp lost when a collar is loaded with 2000 lb, rotates at 50 rpm, and has a coefficient of friction of 0.15. The outside diameter of the collar is 4 inches and the inside diameter is 2 inches. a) 0.7314 Hp b) 0.3714 Hp c) 0.4713 Hp d) 0.4371 Hp
Answer: b) Frictional Horsepower = 0.374 Hp Solution:
fHp
Tf n 63000
f W r f n 63000
0.152000 lb1.56 inches50 rpm 63000
0.3714
2 r o
r i3 2 23 13 Where, r f 1.56 inches 3 r o2 r i2 3 32 12 3
47. Two shafts 3.6 m between centers carry pulleys 1.2 m in diameter and 0.91 m in diameter respectively, connected by a crossed belt. It is desired to put the belt on as an open belt. How long a piece must be cut of it? a) 303.3 mm b) 330 mm c) 333.0 mm d) 330.3 mm Answer: Length to be cut off = 303.3 mm Solution: For the length of an open belt connection,
D 2 D1 2 1200 9102 L o D1 D 2 2C 1200 910 23600 10 520.22 mm 2 4C 43600 2
For the length of belt for crossed belt connection,
Lc
D2 D1 2
2
4C
D1 D2 2C
1200 9102 1200 910 23600 10823.55 mm 43600 2
Solving for the difference of lengths,
L L c L o 10 823.55 10 520.22 303.33 mm 48. A 20-tooth motor sprocket, running at 1200 rpm, drives a blower at a speed ratio of 4:1. Using the largest permissible chain size and the largest permissible center distance of 80 pitches, what length of chain in pitches is required to connect the sprockets? a) 200 pitches b) 212 pitches c) 216 pitches d) 220 pitches Answer: b) Chain length = 21 pitches 2 Solution: L N t1 N t 2 2C N t 2 N t1 212 pitch . es c p
2
40C p
49. A 20-kW motor, running at 1200 rpm, drives a 400 mm diameter pulley at a belt tension ratio of 2.4. If the belt’s tight side tension is only 1200 N, determine the transmission efficiency. a) 87.97 % b) 84.58 % c) 85.66 % d) 86.55 % Answer: a) Transmission Efficiency = 87.97 %
Solution:
Poutput Pinput
Tout n
30 Pinput
1200 n D n D 1200 0.40 Fnet F1 F2 1200 30 2 30 2 30 2 2.4 0.8797 Pinput
Pinput
20 000
50. A right-handed single-thread hardened-steel worm has a catalog rating of 2.25 kW at 650 rpm when meshed with a 48-tooth cast-steel gear. The axial pitch of the worm is 25 mm, normal pressure angle is 14.5 o, and the pitch diameter of the worm is 100 mm. The coefficient of friction is 0.085. Determine the shafts center distance. a) 241 mm b) 142 mm c) 412 mm d) 124 mm
Answer: a) Center distance = 241 mm Solution:
Speed Ratio, SR Tan Tan
L
D w
Dg w n w Tg D g cos g n g Tw D w si n D w tan
p
D w
25
100
4.55o
0.07958
Tg T p Tg p 48 25 D w tan g D w 381.97 mm Tw Tw D w Tw 1 D w D g 100 381.97 Center Distance, C 241 mm
Pitch diameter of the gear, D g
2
2
o
51. A 20 straight-tooth bevel pinion having 14 teeth and a diametral pitch of 6 teeth/inch drives a 42-tooth gear. The two shafts are at right angles and in the same plane. Find the pitch angle of the pinion. o o o o a) 18.4 b) 20 c) 14.5 d) 20.5 Answer: a) Pitch angle = 18.4
o
T p 14 tan 1 18.4 o Tg 42
Solution: tan 1
o
52. A triple-thread worm has a lead angle of 17 and a pitch diameter of 2.2802 inches. Find the center distance when the worm is mated with a wheel of 48 teeth. a) 6.72 inches b) 7.26 inches c) 6.27 inches d) 7.62 inches Answer: a) Center Distance = 6.72 inches
Solution:
Dg
Tg 48 D w tan 2.2802 tan17o 11.154 inches 3 Tw D w Dg 2.2802 11.154 C 6.72 inches 2
2
53. A double-thread worm has a pitch diameter of 3 inches. The wheel has 20 teeth and a pitch diameter of 5 inches. Find the gear helix angle. a) 4.69o b) 9.46o c) 6.49o d) 6.94o Answer: b) Gear helix angle = 9.46 o
Solution:
T D g 5 tan 1 2 tan 1 w 9.46o Tg D w 20 3 o
54. A 36-tooth pinion turning at 300 rpm drives 120-tooth gear of 14.5 involute full depth pressure angle. Determine the rpm of the driven gear. a) 60 rpm b) 45 rpm c) 75 rpm d) 90 rpm Answer: d) 90 rpm
T p 36 300 90 Tg 120
Solution: n g n p
rpm
55. If two parallel shafts are connected by cylinders in pure rolling contact and turning in the same direction, and having a speed ratio of 2.75, what is the Center distance of the two shafts assuming that the diameter of the smaller cylinder is 22 cm? a) 18.25 cm b) 19.25 cm c) 20.25 cm d) 17.25 cm Answer: b) Center Distance = 19.25 cm Solution:
Diameter of the bigger cylinder, D 2 SR D1 2.7522 60.5 cm Center distance, C
D2
D1 2
60.5 22 2
19.25 cm
56. Two extension coil springs are hooked in series that support a single weight of 100 kg. The first spring is rated at 4 kN/m and the other spring is rated at 6 kN/m. Determine the total deflection of the springs. a) 408.6 mm b) 486.0 mm c) 480.6 mm d) 460.8 mm Answer: a) Spring Deflection = 408.6 mm
Solution:
t 1 2
F k 1
F k 2
k k 4 6 F 1 2 100 kg9.8066 N / kg 408.6 mm k k 4 6 1 2
57. If the ultimate shear strength of a steel plates is 42 000 psi, what force is necessary to punch a 0.75 inch diameter hole in a 0.625 inch thick plate? a) 61 850 lb b) 65 810 lb c) 61 580 lb d) 60 185 lb Answer: a) Punching force = 61 850 lb Solution: F su As
su d t 42000lb / in 2 0.75 in 0.625 in 61850.1 lb
58. A stepped torsion shaft has diameters of 16 mm and 12 mm and a fillet radius of 2 mm. The shaft is subjected to a torque of 12.5 N-m. Find the maximum induced stress caused by the fillet. Consider a stress concentration factor of 1.25. a) 36.84 MPaa b) 46.05 MPa c) 38.64 MPa d) 45.06 MPa Answer: b) 46.05 MPa Solution: Solving for the average induced shear stress in the shaft
ss
16T
d
3
16 12.5 3
0.012
36 841422.01 Pa 36.84 MPa
Solving for the maximum induced shear stress, ssmax
r = 2 mm
D = 16 mm
d = 12 mm
k ts ss 1.25 36.84 46.05 MPa
59. A steam engine that has a stroke of 12 inches has an overhung crank of 11 inches. The maximum tangential force, P, on the crank may be assumed as 75000 lb. Assuming an allowable stress in shear as 4400 psi, determine the crankshaft diameter. a) 4.77 inches b) 3.77 inches c) 2.77 inches d) 1.77 inches Answer: a) Crankshaft Diameter = 4.77 inches Solution: Solving for the torque, T P R 75006 45 000 in lb
B
A
Crankpin
6”
11” Crankshaft
Solving for the bending moment, M 750011 82 500 in lb Solving for the shaft diameter, 1
1
16 3 3 M2 T 2 16 45 0002 82 5002 4.77" D ss 4400 60. A parallel helical gear-set consists of a 19-tooth pinion driving a 57-teeth gear. The pinion has a left-hand helix o o angle of 20 , a normal pressure angle of 14½ , and a normal diametal pitch of 10 teeth/inch. If the pinion is to transmit 50 Hp at a speed of 1750 rpm. Determine the center distance of the two gears. a) 2.02 inches b) 6.06 inches c) 4.04 inches d) 2.06 inches Answer: c) 4.04 inches
Solution:
Pdn
Pd cos cos
T p D p cos cos
Tg D g cos cos
Pitch diameter of the pinion, D p
T p Pdn cos cos
19 10 cos cos 20
o
2.02 inches
Tg 57 D p 2.02 6.06 inches T p 19 D p Dg 2.02 6.06 C 4.04 inches
Pitch Diameter of the gear, D g
Center-to-center distance,
2 2 61. A single square thread power screw is to raise a load of 70 kN. The screw has a major diameter of 36 mm and a pitch of 6 mm. The coefficient of thread friction and collar friction are 0.13 and 0.10 respectively. If the collar mean diameter is 90 mm and the screw turns at 60 rpm, find the axial linear speed of the screw. a) 5 mm/s b) 6 mm/s c) 7 mm/s d) 5.5 mm/s Answer: b) 6 mm/s Solution: For the linear speed of the screw, Vn = n (L) = (60 rpm)(6 mm/rev) = 360 mm/min = 6 mm/s 62. Select a deep-groove ball bearing to carry a radial load F x = 800 lb and a thrust load Fz = 700 lb at 1800 rpm. The service is 8 hr/day, but it is not continuous; design for 18 250 hr. The operation is smooth with little vibration; the outer ring rotates. Determine the design life in million revolution (mr) with no more than 10 % failure. b) 1971 mr a) 1791 mr c) 1197 mr d) 1917 mr 63. If the ultimate shear strength of a steel plates is 42 000 psi, what force is necessary to punch a 0.75 inch diameter hole in a 0.625 inch thick plate? a) 61 850 lb b) 65 810 lb c) 61 580 lb d) 60 185 lb 64. Find the pressure required to punch a 1-inch square hole in ¼ -inch thick steel. a) 20.67 tons b) 26.76 tons c) 26.67 tons
d) 26.67 tons
65. What length of a square key is required for a 4-in diameter shaft transmitting 1000 hp at 1000 rpm? The allowable shear and compressive stresses in the key are 15 ksi and 30 ksi, respectively. a) 2.1 inches b) 2.8 inches c) 3.2 inches d) 4.2 inches
66. A flange coupling is to transmit 15,000 in-lb in- lb between two 2.5” diameter shafts. How many ½” diameter bolts in a 6” diameter bolt circle are required if the shear stress in each bolt is limited to 3000 psi? b) 7 bolts c) 6 bolts d) 8 a) 9 bolts bolts 67. Determine the radius of gyration of a wheel that has an outside and inside diameters of 1 meter and 0.75 meter, respectively? Neglect its hub and arms. a) 0.5125 m b) 0.6125 m c) 0.3125 m d) 0.4125 m 68. What is the polar section modulus of a solid shaft with a diameter of 101.6 mm? 3 3 4 c) 205.9 cm a) 209.5 cm b) 209.5 cm
4
d) 205.9 cm
o
69. If the angular deformation of a solid shaft should not to exceed 1 in a length of 1.8 m and the allowable 6 shearing stress is 83 MMa, what is the diameter of the shaft? Assume that the shaft material has G = 77 x 10 kPa. a) 222.34 mm b) 234.22 mm c) 23.42 cm d) 24.22 cm 70. What modulus of elasticity in tension is required to obtain a unit deformation of 0.00105 from a load producing 2 a unit tensile stress of 3163.27 kg/cm ? 6 6 6 6 b) 43 x 10 psi a) 40 x 10 psi c) 45 x 10 psi d) 46 x 10 psi 71. If the ultimate shear strength of a steel plates is 42 000 psi, what force is necessary to punch a 0.75 inch diameter hole in a 0.625 inch thick plate? a) 61 850 lb b) 65 810 lb c) 61 580 lb d) 60 185 lb 72. Determine the tensile stress area of an American Standard Screw Threads 6-32 UNC with basic major diameter of 0.1380 inch. -3 2 -2 2 -4 2 -5 a) 9.085 x 10 in b) 9.085 x 10 in c) 9.085 x 10 in d) 9.085 x 10 2 in 73. What is the number of threads per mm and the tensile stress area of a standard Metric screw Thread designated by M10 x 1.5? 2 2 2 b) 0.667 and 57.99 mm a) 0.555 and 57.99 mm c) 1.5 and 57.99mm d) 1.75 and 57.99 2 mm 74. A line shaft is to transmit 200 Hp at 900 rpm. Find the diameter of the shaft. b) 2.28 inches a) 2.18 inches c) 3.18 inches
d) 3.28 inches
75. A round steel shaft rotates at 200 rpm and is subjected to a torque of 275 N-m and a bending moment of 415 Nm. Determine the equivalent twisting moment. d) 497.85 N-m a) 597.84 N-m b) 456.42 N-m c) 546.43 N-m 76. A 75-mm diameter shaft is transmitting 300 kW at 600 rpm. A flange coupling is used and has 6 bolts, each 18 mm in diameter. Find the required diameter of the bolts circle based on an average shearing stress of 27.5 MPa. b) 477.2 mm c) 274.7 mm d) 247.7 mm a) 227.4 mm 77. A 1.75-inch-diameter shaft is supported by two sleeve bearings. The total load on the two bearings is 2800 lb. Find the friction power loss, in Hp, if the coefficient of friction between shaft and bearing is 0.10 and the shaft rotates 200 rpm. b) 0.78 Hp a) 0.88 Hp c) 0.98 Hp d) 0.68 Hp 78. Determine the Hp lost when a collar is loaded with 2000 lb, rotates at 50 rpm, and has a coefficient of friction of 0.15. The outside diameter of the collar is 4 inches and the inside diameter is 2 inches. b) 0.3714 Hp a) 0.7314 Hp c) 0.4713 Hp d) 0.4371 Hp
79. A vertical steel cylinder water tank is 30 m in diameter and 45 m high. The allowable stress of the steel plate is 1224 kg/cm2. Without reinforcing angle bars and rods, what is the thickness of the steel plate? b) 51.55 mm c) 65.15 mm d) 61.55 mm a) 55.15 mm 80. What is the bursting steam pressure of a hemispherical steel shell with a diameter of 100 inches and made of 0.0635-m thick steel plate, if the joint efficiency is 70 % and the tensile strength is 60 000 psi? b) 4 200 psi a) 4 020 psi c) 2 400 psi d) 2 040 psi 81. The root diameter of a double square thread is 0.55 inch. The screw has a pitch of 0.2 inch. Find the outside diameter and the number of thread per inch. c) 5 threads/inch a) 0.2 threads/inch b) 10 threads/inch d) 2.5 threads/inch 82. Two shafts 3.6 m between centers carry pulleys 1.2 m in diameter and 0.91 m in diameter respectively, connected by a crossed belt. It is desired to put the belt on as an open belt. How long a piece must be cut of it? a) 303.3 mm b) 330 mm c) 333.0 mm d) 330.3 mm 83. A flat belt is 6 inches wide and 1/3 inch thick and transmits 15 Hp. The center distance is 8 ft. The driving pulley is 6 inches i n diameter and rotates at 2 000 rpm such that the loose side of the belt is on top. t op. The driven 3 pulley is 18 inches in diameter. The belt material is 0.035 lb/in and the coefficient of friction is 0.30. Determine the belt net tension. b) 157.5 lb a) 175.5 lb c) 155.7 lb d) 165.7 lb 84. A pulley 600 mm in diameter transmits 40 kW at 500 rpm. The arc of contact between the belt and pulley is o 144 , the coefficient of friction between belt and pulley is 0.35 and the safe working stress of the belt is 2.1 MPa. Determine the belt tensions ratio, neglecting the effect of centrifugal force. a) 2.41 b) 2.14 c) 1.24 d) 4.12 85. A roller chain and sprocket is to drive vertical centrifugal discharge bucket elevator. The pitch of chain connecting sprockets is 1.75”. The driving sprocket is rotating at 120 rpm and has 11 teeth while the driven sprocket is rotating at 38 rpm. Determine the number of teeth of driven sprocket. b) 35 teeth a) 33 teeth c) 30 teeth d) 34 teeth 86. A helical steel spring has a maximum load of 800 lb and a corresponding deflection of 2 inches. If it has 8 active coils and an index of 6, what minimum shear strength of the spring material is required? c) 67 ksi a) 57 ksi b) 47 ksi d) 37 ksi 87. A helical-coil spring has a mean coil diameter of 1 inch and a wire diameter of 1/8 inch. Determine the value of Bergstrasssar factor of the spring. a) 1.172 b) 1.712 c) 1.217 d) 1.271 88. A precision cut gear transmits 25 Hp at a pitch line velocity of 6000 fpm. If the service is intermittent, find the dynamic load. b) 274.05 lb a) 247.05 lb c) 275.04 lb d) 247.05 lb 89. What is the difference of the values of the Wahl factor and the Bergstrasser factor, in percentage? b) Less than 1 % a) 1 % c) Greater than 1 %
d) 0.5 %
90. A double-thread worm has a pitch diameter of 3 inches. The wheel has 20 teeth and a pitch diameter of 5 inches. Find the gear helix angle. o b) 9.46 a) 4.69o c) 6.49o d) 6.94o 91. A helical-coil spring has a mean coil diameter of 1 inch and a wire diameter of 1/8 inch. Determine the shearstress augmentation factor of the spring. b) 1.0625 a) 1.625 c) 1.0256 d) 1.0526
92. A disc clutch has 6 pairs of contacting friction surfaces with an outside diameter of 200 mm and an inside diameter of 100 mm. The coefficient of friction of the clutch materials is 0.4 and the axial force is 1500 N. The shaft speed is 1200 rpm. Determine the Hp that can be transmitted by the clutch assuming uniform pressure. a) 35.2 Hp b) 23.5 Hp d) 27.4 Hp c) 47.2 Hp 93. A flywheel has a mean diameter of 4 ft and is required to handle 2250 ft-lb of kinetic energy. It has a width of 8 inches, mean operating speed is 300 rpm and the coefficient of fluctuation is to be 0.05. Find the weight of rim, assuming that the arms and hub are equivalent to 10 % of the total rim weight. The flywheel is made up of cast iron with specific weight of 0.26 lb per cubic inch. a) 333.7 lb b) 373.3 lb c) 337.3 lb d) 733.3 lb o
94. A 20 involute spur gear has a tooth whole depth of 16.95 mm, a tooth thickness of 13.2 mm, and a pitch of 3. Determine the circular pitch of the gear. a) 26.6 mm b) 16.6 mm c) 25.6 mm d) 24.6 mm 95. A parallel helical gear-set consists of a 19-tooth pinion driving a 57-teeth gear. The pinion has a left-hand helix angle of 20o, a normal pressure angle of 14½ o, and a normal diametal pitch of 10 teeth/inch. If the pinion is to transmit 50 Hp at a speed of 1750 rpm. Determine the center distance of the two gears. c) 4.04 inches a) 2.02 inches b) 6.06 inches d) 2.06 inches 96. A right-handed single-thread hardened-steel worm has a catalog rating of 2.25 kW at 650 rpm when meshed with a 48-tooth cast-steel gear. The axial pitch of the worm is 25 mm, normal pressure angle is 14.5 o, and the pitch diameter of the worm is 100 mm. The coefficient of friction is 0.085. Determine the shafts center distance. a) 241 mm b) 142 mm c) 412 mm d) 124 mm o
97. A 20 straight-tooth bevel pinion having 14 teeth and a diametral pitch of 6 teeth/inch drives a 42-tooth gear. The two shafts are at right angles and in the same plane. Find the pitch angle of the pinion. o o o o a) 18.4 b) 20 c) 14.5 d) 20.5 98. A triple-thread worm has a lead angle of 17 o and a pitch diameter of 2.2802 inches. Find the center distance when the worm is mated with a wheel of 48 teeth. a) 6.72 inches b) 7.26 inches c) 6.27 inches d) 7.62 inches 99. A double-thread worm has a pitch diameter of 3 inches. The wheel has 20 teeth and a pitch diameter of 5 inches. Find the gear helix angle. o o o o b) 9.46 a) 4.69 c) 6.49 d) 6.94 o
100.A 100. A 36-tooth pinion turning at 300 rpm drives 120-tooth gear of 14.5 involute full depth pressure angle. Determine the rpm of the driven gear. d) 90 a) 60 rpm b) 45 rpm c) 75 rpm rpm 101.Three 101. Three extension springs are hooked in series that support a single weight of 100 kg. The first spring is rated at 4 kN/m and the other two springs are rated 6 kN/m each. Determine the equivalent stiffness of the three springs. b) 5 kN/m c) 2.71 kN/m d) 3.71 kN/m a) 1.71 kN/m 102.Three 102. Three extension springs are hooked in parallel that support a single weight of 100 kg. The springs are rated 4 kN/m, 5 kN/m, and 6 kN/m, respectively. Determine the equivalent spring constant of the three springs. b) 15 kN/m a) 10 kN/m c) 9 kN/m d) 11 kN/m 103.A 103. A single square thread power screw is to raise a load of 70 kN. The screw has a major diameter of 36 mm and a pitch of 6 mm. The coefficient of thread friction and collar friction are 0.13 and 0.10 respectively. If the collar mean diameter is 90 mm and the screw turns at 60 rpm, find the axial linear speed of the screw. b) 6 mm/s a) 5 mm/s c) 7 mm/s d) 5.5 mm/s
104.A 104. A double thread ACME screw driven by a motor at 400 rpm raises the attached load of 900 kg at a speed of 10 m/min. The screw has a pitch diameter of 36 mm; the coefficient of friction on threads is 0.15. The friction torque on the thrust bearing of the motor is taken as 20 % of the total input. Determine the lead angle. o b) 14.265o c) 15.462o d) 16.452o a) 12.465 105.What 105. What is the minimum clearance allowed for meshing spur gears with diametral pitch of 20? The spur gear has 25 teeth. a) 0.00785 inch b) 0.00758 inch c) 0.00857 inch d) 0.00758 inch 106.A 106. A wire rope lifts a load of 10 kips at a maximum speed of 1000 feet per minute, attained in 5 seconds starting 2 from rest. The rope has a metallic cross sectional area of 0.4 in . Determine the maximum tensile stress on the rope in ksi. a) 26.2 b) 25.0 c) 27.6 d) 32.4 107.A 107. A casting weighing 300 pounds is to be lifted by means of an overhead crane. The casting is lifted 10 feet in 12 seconds. What is the horsepower developed? a) 0.54 b) 0.84 c) 0.95 d) 0.45 108.What 108. What wall thickness is required for a 500mm diameter cylinder under an internal pressure of 20 MPa? Use a design stress of 80 MPa. a) 73 mm b) 53 mm c) 63 mm d) 83 mm
View more...
Comments
