Jsa for Pmi Test at Shell Pd

JOB SAFETY ANALYSIS JOB WORK TEAM NO 1

DATE :

TO PERFORM PMI TEST NDT TECH

PERMIT TYPE (COLD/HOT/BURN):

COLD WORK PERMIT

BASIC JOB STEPS Preparing of work permit

PERMIT NO :

POTENTIAL HAZARDS

CONTROLS

Conflict with other permit

Read the permit and brief the work scope during permit coordication

Miscommunication with other work group.

meeting. Ensure the other group understand our work scope and location

Permit violation

where the jobs to be done. Ensure the working permit is approved and signed by all respective supervisors.

2 Work site inspection.

Congested area.

Familiarise working area such a blocking of escape route to emergency assambly area.

Open deck floor/grating.

Locate the deck floor without cover/grating and do not try to walk at this area. Hot area. Beware of hot air from generator turbine which blowing to riser area. Uneven grating or floor. Beware of uneven grating where can couse tripping hazzard. High pressure area. Keep away from any high high pressure equipment at cellar deck. Do not touch any valves at the high pressure system. WHAT TO CHECK AND NOT LIMITED TO WITH REFERENCE TO APPENDIX A & B OF THE OFFSHORE WORK PERMIT SYSTEM MANUAL:EXPERIENCE

YES NO

Have you done this job before? Have you referred technical drawing/ Vendor procedure/SSP?

YES YES

PPE

YES NO

YES NO

Hard Hat?

YES

Face shield?

Safety Glasses?

YES

Right type of gloves?

Safety Shoes?

YES

Safety harness?

YES NO Are you knowledgeable with the job to be performed?

YES NO

Is supervision/experienced assistance required? YES NO

NO

Work Vest?

YES YES

Apron? Goggle?

YES NO

YES

Ear Plugs, double protection? NO

Respiratory protection?

YES NO

NO

POTENTIAL HAZARDS O

Slippery floor?

O

Pinchh/Trap finger,hand?

O

Trap pressure?

O

High noise area?

O

Congested area?

O

Back injury hazard?

O

Pressurized equipment/vessel hazard?

O

Spark/Hot slag?

O

Tripping?

O

Swinging object?

O

Fire/Explosion hazards?

O

Burn (heat/chem)?

O

Overhead work?

O

Falling object?

O

Escape route?

O

Near radioactive materials/sources?

O

Working at height?

O

Others closeby?

O

Shock/Electricity/Static?

O

Environment spill?

O

Scaffolding?

O

Sharp object?

O

Breaker rack out?

O

Hose connection?

O

Secure ladder

O

Eye injury?

O

Valve isolation

O

Windy?

O

Heavy load?

O

Grating/deck opening?

O

Guard rotating equipment?

O

Dusty?

O

Hammer strike?

O

Blocked drains?

O

Power tools hazards?

O

1 of 2

JOB SAFETY ANALYSIS JOB TO PERFORM MPI TEST WORK TEAM NDT TECH NO BASIC JOB STEPS 3 PMI test

DATE :

PERMIT NO :

PERMIT TYPE (COLD/HOT/BURN):

POTENTIAL HAZARDS Hot surface/piping. High noise area. Hand injury. Hot area. Tripping hazard. Falling objects. Over board.

COLD WORK PERMIT CONTROLS Wear a suitable hand glove for the protection from any hot surface or object. Wear a proper ear protection such a recommended ear plug or ear mufler. Wear a recommended hand glove. Beware of rotation equipment such a pump fan and motor. Minimise the duration at working area. Beware of any protuding object during walking at deck floor or grating. Place all tool and equipment at suitable floor. Wear a proper safety gear such a work vest and safety harness. Safety harness should be hocked at strong structure such a s/fold handrailing.

Radiation(Low)

Make sure there are no other person in front of the equipment during the test was done.

Falling from ladder step

Ensure the step of ladder is free from grease or oil. To prevent from slippery during stepping on the ladder step.

5 Measuring the finding

Wrong measurement.

Measure in detail area

6 House keeping.

Massive working place.

Clean up working area. Return the ladder to the place.

Prepared by:

Reviewed by:

Close out:

2 of 2