IT01 09AggAeterna En

AETERNA PROGRAMMING AND UPDATE

IT01/10

The Aeterna Change Giver Coin Mechanism is a device able to recognize the coins and address them to 5 different accumulation tubes. After a sale operation the Change Giver gives back any excess credit.

Versions available: Aeterna is available in three versions: Executive, MDB and BDV according to the managed communication protocol and, as a consequence, to the connecting harness towards the vending machine supplied. Furthermore, with the proper parallel interface it is possible to install the Aeterna Executive coin mechanism in the electromechanical vending machines too (in this case without managing an outside display). The Executive version is equipped with an MDB bus where up to two peripherals can be connected at the same time: an MDB cashless payment system and an MDB bill validator.

Accessories necessary for programming and update: • • • • • • • •

Personal Computer (IBM compatible PC with Pentium 2 microprocessor or above, 32 MB RAM recommended, 50 MB hard disk space. Microsoft Windows 9x/ME/NT/2000/XP/7 operating system with Internet Explorer rel. 5.5); FlashManager Software (rel.1.24 or above); EasyCoinProfit Software (rel.1.20, database rel.1.18 or above); Firebird Software (rel.1.53 or above); Maxi Programmer (cod. 932244); Harness between PC and Maxi Programmer (cod.346460); Programming interface for Systems and Validators by PC (cod.844030); Harness for firmware update of PROFIT Validator/Separator group by Maxi Programmer (cod.346533);

Page 1 of 10

AETERNA PROGRAMMING AND UPDATE FIRMWARE UPDATE OF FLASH MICROPROCESSOR ON AETERNA BASE BOARD Update by means of Personal Computer Necessary accessories: • •

FlashManager software (which can be downloaded from the website www.coges.eu ); Programming interface for Systems and Validators by PC (cod.844030).

Operations to be carried out: • Connect the Programming interface for Systems and Validators by PC (dipswitch on Flash position) to the serial port of the PC and to the J4 connector of the Aeterna base board; • Power the Aeterna Change Giver and start the FlashManager program; • Select the file corresponding to the release that you intend to transfer to the Change Giver; • Configure the serial port corresponding to the “Microprocessor” programming mode and proceed by pressing the microprocessor icon; • Wait for the message “Update ended successfully” and then switch off the Change Giver and disconnect the harness from it. • Check the firmware release on the programming menu (“Diagnostics” item).

Note: The file of the firmware release can be downloaded from the corresponding page of our website and copied in the PC inside a folder. The file used has got a .cse extension.

Page 2 of 10

IT01/10

AETERNA PROGRAMMING AND UPDATE

FIRMWARE UPDATE OF FLASH MICROPROCESSOR ON AETERNA BASE BOARD Update by means of Maxi Programmer Necessary accessories: • • • •

FlashManager software (which can be downloaded from the website www.coges.eu ); Maxi Programmer (cod. 932244); Maxi Programmer/PC programming harness (cod. 346460 supplied with the programmer); Harness between Maxi Programmer/PROFIT validator firmware (cod.346533).

Maxi Programmer programming for Flash update of base board (see on page 8) Operations to be carried out: • • • •

Connect the Maxi Programmer/PROFIT validator firmware harness to the Maxi Programmer and to the J4 connector of the Aeterna base board; Switch on the Maxi Programmer and place on the memory area called “FlashAeterna” where the Flash release was programmed with FlashManager; Make sure that the change giver is powered, then by using the Start key, make programming starts; Wait for the message “Programming ended successfully” then switch off the Change Giver, disconnect the harness and check that when the Aeterna is switched on again, it performs correctly the restart cycle. Page 3 of 10

IT01/10

AETERNA PROGRAMMING AND UPDATE FIRMWARE UPDATE OF FLASH MICROPROCESSOR ON VALIDATOR/SEPARATOR GROUP Update by means of Personal Computer Necessary accessories: • •

FlashManager software (which can be downloaded from the website www.coges.eu ); Programming interface for Systems and Validators by PC (cod.844030).

Operations to be carried out: • • • • •

Connect the Programming interface for Systems and Validators by PC (dip-switch on Flash position) to the serial port of the PC and to the J6 connector of the Validator/Separator group; Power the Aeterna Change Giver and start the FlashManager program; Select the file corresponding to the release that you intend to transfer to the Validator/Separator group; Configure the serial port corresponding to the “Microprocessor” programming mode and proceed by pressing the microprocessor icon; Wait for the message “Update ended successfully”, then switch off the Change Giver, disconnect the interface from the validator and check that when the Aeterna is switched on again it performs correctly the restart cycle;

Note: The file of the firmware release can be downloaded from the corresponding page of our website and copied in the PC inside a folder. The file used has got a .cse extension.

Page 4 of 10

IT01/10

AETERNA PROGRAMMING AND UPDATE FIRMWARE UPDATE OF FLASH MICROPROCESSOR ON VALIDATOR/SEPARATOR GROUP Update by means of Maxi Programmer Necessary accessories: • • • •

FlashManager software (which can be downloaded from the website www.coges.eu ); Maxi Programmer (cod. 932244); Maxi Programmer/PC programming harness (cod. 346460 supplied with the programmer); Harness between Maxi Programmer/PROFIT validator firmware (cod.346533).

Maxi Programmer programming for Flash update of Aeterna Validator/Separator group (see page 9) Operations to be carried out: • • • •

Connect the Maxi Programmer/PROFIT validator firmware harness to the Maxi Programmer and to the Validator/Separator group; Switch on the Maxi Programmer and place on the memory area called “FlashReader” where the Flash release was programmed with FlashManager; Make sure that the Validator/Separator group is powered, then by using the Start key, make programming starts; Wait for the message “Programming ended successfully” then switch off the Change Giver, disconnect the validator’s harness and check that when the PROFIT is switched on again, it performs correctly the restart cycle.

Page 5 of 10

IT01/10

AETERNA PROGRAMMING AND UPDATE UPDATE OF COIN DATABASE ON THE BASE BOARD Update by means of Personal Computer Necessary accessories: • •

EasyCoinProfit software (which can be downloaded from the website www.coges.eu ); PC programming interface for Systems/Validators (cod.844030).

Operations to be carried out: • • • • •

Connect the PC programming interface for Systems/Validators (dipswitch on Parameter Programming position) to the serial port of the PC and to the base board of the Aeterna Change Giver (connector J4); Power the Aeterna and make the EasyCoinProfit software start; By means of the “Models” key, choose the configuration you intend to program (ex: 5c/10c/20c/50c/5c Euro); Start programming by using the “Programming” key; Wait for the message “Programming ended successfully” then switch off the Change Giver, disconnect the harness from the board and check that when the Aeterna is switched on again, it performs correctly the restart cycle.

Page 6 of 10

IT01/10

AETERNA PROGRAMMING AND UPDATE UPDATE OF COIN DATABASE ON THE BASE BOARD Update by means of Personal Computer Necessary accessories: • • • •

FlashManager software (which can be downloaded from the website www.coges.eu ); Maxi Programmer (cod. 932244); Maxi Programmer/PC programming harness (cod. 346460 supplied with the programmer); Harness between Maxi Programmer/PROFIT validator firmware (cod.346533).

Maxi Programmer programming for Coin database update of Aeterna change giver (see page 10) Operations to be carried out: • • • •

Connect the Maxi Programmer/PROFIT validator firmware harness to the Maxi Programmer and to the J4 connector of the Aeterna base board; Switch on the Maxi Programmer and place on the memory area called “Mod.AeternaProfit” where the Coin database was programmed with EasyCoinProfit; Make sure that the change giver is powered, then by using the Start key, make programming starts; Wait for the message “Programming ended successfully” then switch off the Change Giver, disconnect the harness and check that when the Aeterna is switched on again, it performs correctly the restart cycle.

Page 7 of 10

IT01/10

AETERNA PROGRAMMING AND UPDATE

IT01/10

Maxi Programmer programming to update the Flash of the Aeterna base board Operations to be carried out: • • • • •

Connect the harness between PC and Maxi Programmer (cod. 346460 parameter connector) to the serial port of the PC and to the Maxi Programmer, which is switched on and placed on the memory area called “FlashAeterna” and reserved to the Flash programming; Start the FlashManager software; Select the file corresponding to the release that you intend to transfer to the Change Giver base board; Configure the serial port corresponding to the “Maxi Programmer” programming mode and proceed by pressing the Maxi Programmer icon; Wait for the message “Update ended successfully”, then disconnect the Maxi Programmer.

Note: The file of the firmware release can be downloaded from the corresponding page of our website and copied in the PC inside a folder. The file used has got a .cse extension.

Page 8 of 10

AETERNA PROGRAMMING AND UPDATE

IT01/10

Maxi Programmer programming to update the Flash of the Validator/Separator group Operations to be carried out: • • • • •

Connect the harness between PC and Maxi Programmer (cod. 346460 parameter connector) to the serial port of the PC and to the Maxi Programmer, which is switched on and placed on the memory area called “FlashReader” and reserved to the Flash programming; Start the FlashManager software; Select the file corresponding to the release that you intend to transfer to the validator group; Start programming by using the “Programming” key; Wait for the message “Update ended successfully”, then disconnect the Maxi Programmer.

Note: The file of the firmware release can be downloaded from the corresponding page of our website and copied in the PC inside a folder. The file used has got a .cse extension.

Page 9 of 10

AETERNA PROGRAMMING AND UPDATE

IT01/10

Maxi Programmer programming to update the Coin Database Operations to be carried out: • • • • •

Connect the harness between PC and Maxi Programmer (cod. 346460 parameter connector) to the serial port of the PC and to the Maxi Programmer, which is switched on and placed on the memory area called “Mod.AeternaProfit” and reserved to the Coin database programming; Start the EasyCoinProfit software; Select the configuration you intend to transfer to the Change Giver base board (ex: 5c/10c/20c/50c/5c Euro); Start programming by using the “Programming” key; Wait for the message “Update ended successfully”, then disconnect the Maxi Programmer.

Page 10 of 10