INTERNATIONAL STANDARD
ISO 9712 Fifth edition 2021-12
Non-destructive testing — Qualiication and certiication of NDT personnel Essais non destructifs — Qualiication et certiication du personnel END
Reference number ISO 9712:2021(E)
© ISO 2021
ISO 9712:2021(E)
COPYRIGHT PROTECTED DOCUMENT © ISO 2021
All rights reserved. Unless otherwise speciied, or required in the context of its implementation, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of the requester. ISO copyright ofice CP 401 • Ch. de Blandonnet 8 CH-1214 Vernier, Geneva Phone: +41 22 749 01 11 Email:
[email protected] Website: www.iso.org Published in Switzerland
ii
© ISO 2021 2021 – All rights reser ved
ISO 9712:2021(E)
Contents
Page
Foreword. .........................................................................................................................................................................................................................................v Introduction .............................................................................................................................................................................................................................vii 1
Scope ................................................................................................................................................................................................................................. 1
2
Normative references ..................................................................................................................................................................................... 1
3
Terms and deinit deinitions ions .................................................................................................................................................................................... 2
4
Abbreviated terms ............................................................................................................................................................................................. 6
5
Responsibilities. .................................................................................................................................................................................................... 6 5.1 General. .......................................................................................................................................................................................................... 6 5.2 Certiication body ................................................................................................................................................................................ 6 5.3 Authorized qualiic qualiication ation body. ................................................................................................................................................. 8 5.4 Examination Examin ation centre ............................................................................................................................................................................ 8 5.5 Employer ...................................................................................................................................................................................................... 8 5.6 Candidate. .................................................................................................................................................................................................... 9 5.7 Certiicate Certi icate holde holders rs ............................................................................................................................................................................... 9 5.8 Examiners ................................................................................................................................................................................................ 10 5.9 Referee ........................................................................................................................................................................................................ 10
6
Levels of certiication .................................................................................................................................................................................. 10 6.1 6.2 6.3
Level 1 ......................................................................................................................................................................................................... 10 Level 2 ......................................................................................................................................................................................................... 10 Level 3 ......................................................................................................................................................................................................... 11
7
Eligibility ................................................................................................................................................................................................................... 11 7.1 General. ....................................................................................................................................................................................................... 11 7.2 Training. ..................................................................................................................................................................................................... 11 7.3 Industriall NDT experience........................................................................................................................................................ 13 Industria 7.3.1 General ..................................................................................................................................................................................... 13 7.3.2 Level 3 ....................................................................................................................................................................................... 13 7.3.3 Possible reductions ....................................................................................................................................................... 14 7.4 Vision requirements — all levels ........................................................................................................................................ 14 7.4.1 General ..................................................................................................................................................................................... 14 7.4.2 Near vision acuit acuity y. .......................................................................................................................................................... 14 7.4.3 Colour vi vision sion ....................................................................................................................................................................... 14 7.4.4 Personnel administ administering ering vision test testss ........................................................................................................... 15
8
Examinations ........................................................................................................................................................................................................ 15 8.1 Overview ................................................................................................................................................................................................... 15 8.1.1 General ..................................................................................................................................................................................... 15 8.1.2 Examinat Examination ion elemen elements ts ................................................................................................................................................ 15 8.1.3 Examinat Examination ion time ........................................................................................................................................................... 16 8.1.4 Examinat Examination ion aids ............................................................................................................................................................ 16 8.2 Examination Examin ation content and grading for Level 1 and Level 2 ........................................................................... 16 8.2.1 General examinat examination ion elemen element t .............................................................................................................................. 16 8.2.2 Speciic examinat examination ion elemen element t .............................................................................................................................. 16 8.2.3 Pract Practical ical examinat examination ion elemen element t ........................................................................................................................... 16 ................................................................................... 17 8.2.4 NDT inst instruction ruction writ writing ing examinat examination ion element ................................................................................... 8.2.5 Grading of the Level 1 and Level 2 examinat examination ion ................................................................................. 17 8.3 Examination Examin ation content and grading for Level 3.......................................................................................................... 18 8.3.1 General ..................................................................................................................................................................................... 18 8.3.2 Basic examinat examination ion element .................................................................................................................................... .................................................................................................................................... 18
8.4 8.5
8.3.3 Main method examinat examination ion elemen element t ................................................................................................................ 19 8.3.4 Grading of Level 3 examinat examinations ions. ...................................................................................................................... 19 Conduct Condu ct of examinat examinations ions ............................................................................................................................................................ 20 Re-examination. .................................................................................................................................................................................. 20
© ISO 2021 – All rights r eserved
iii
ISO 9712:2021(E)
8.6 9
Supplementary Suppl ementary examinat examinations ions ................................................................................................................................................ 21
Certiication ........................................................................................................................................................................................................... 21 9.1 Administration .................................................................................................................................................................................... 21 9.2 Certiicates .............................................................................................................................................................................................. 21 9.3 Conditions of certi certiicat ication ion. ........................................................................................................................................................ 22 9.3.1 General ..................................................................................................................................................................................... 22 9.3.2 Granting................................................................................................................................................................................... 22
9.4
................................................................................................................................................................ 22 9.3.3 extension 9.3.4 Scope Suspension of certi certiicat ication ion ..................................................................................................................................... 22 9.3.5 Withdrawal of certi certiicat ication ion ................................................................................................................................... 22 9.3.6 Certiication after withdrawal............................................................................................................................ 23 9.3.7 Waiting period prior to certi certiicat ication ion aft after er withdr withdrawal awal ............................................................... 23 Certiicates Certi icates issued by other certi certiicat ication ion bodies .................................................................................................. 23
10
Renewal ...................................................................................................................................................................................................................... 23
11
Recertiication.....................................................................................................................................................................................................24 11.1 General. ....................................................................................................................................................................................................... 24 11.2 Levels 1 and 2 ....................................................................................................................................................................................... 25 11.3 Level 3 ......................................................................................................................................................................................................... 25
12
Files ................................................................................................................................................................................................................................. 26
13
Transition Trans ition period ............................................................................................................................................................................................. 27
Annex A (normative) Sectors .................................................................................................................................................................................... 28 Annex B (normative) Minimum number and type of specimens for the Level 1 and Level 2 ..........................................................................................................................................................30 practical examination element .......................................................................................................................................................... Annex C (normative) Structured credit system for renewal Level 1, 2 and 3 and for Level 3 recertiication. ..................................................................................................................................................................................................... 31 Annex D (normative) Grading practical examination elements ......................................................................................... 35 Annex E (informative) Engineering of NDT ............................................................................................................................................... 37 Annex F (informative) Training requirements for techniques ............................................................................................ 38 Annex G (informative) Psychometric principles .................................................................................................................................. 41 Bibliography. ............................................................................................................................................................................................................................ 42
iv
© ISO 2021 2021 – All rights re served
ISO 9712:2021(E)
Foreword ISO (the International Organization Organi zation for Standardization Standardizat ion)) is a worldwide worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardizatio st andardization. n. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives www.iso.org/directives). ). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identiied during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation voluntary nature of standards, meaning about of ISO ISO's speciic terms and expressions related of to the conformity assessment, as well as the information adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html . This document was prepared by Technical Committee ISO/TC 135, Non-destructive testing, Subcommittee SC 7, Personnel qualiication, in collaboration with the European Committee for Standardization (CEN) Technical Committee CEN/TC 138, Non-destructive testing, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement). This ifth edition cancels and replaces the fourth edition (ISO 9712:2012), which has been technically revised. The main changes compared to the previous edition are as follows: — clariied clari ied responsibilities for the cert certiicat iication ion body body,, the authorized authorized qualiication body, body, the examination centre and the t he employer; employer; — added and revised deinit deinitions; ions; — deined responsibilities for for examiners and referees; — revised requirements for the duration of trai training ning and industri industrial al experience; — modiied requirements for visua visuall acuity test testing; ing; — revised requirements for examinat examinations; ions; — included an option for the use of a psychometric psychometric process at the discretion of the certiication certi ication body; — revised requirements for the certi certiicat ication ion documents; — revised requirements requirements for the conditions of certi certiicat ication; ion; — added requirements for for candidates for the renewal of certi certiicates; icates; — revised structured credit system system for for Level Level 3 recertiication; — included a new Annex F for F for techniques; © ISO 2021 – All rights r eserved
v
ISO 9712:2021(E)
— included a new Annex G for G for psychometric principles; — other minor technica technicall and editorial changes. Any feedback or questions on this document should be directed to the t he user’s national standards standar ds body. A complete listing of these bodies can be found at www.iso.org/members.html .
vi
© ISO 2021 2021 – All rights re served
ISO 9712:2021(E)
Introduction Since the effectiveness of any application of non-destructive testing (NDT) depends upon the capabilities of the t he persons who perform or are responsible for the test, a procedure has been developed to provide a means of evaluating and documenting the competence of personnel whose duties require the appropriate theoretical and practical knowledge of the non-destructive tests they perform, specify, supervise, monitor or evaluate. An added incentive stems from the worldwide comparability of a wide range of industrial applications requiring common non-destructive testing approaches. When certiication of NDT personnel is required in product standards, regulations, codes or speciications, it is important to certify the personnel in accordance with this document. When latitude is provided in the criteria within this document, the certiication body has the inal decision in determining speciic requirements. When there is no requirement in legislation, in standard or in the order for certiication of NDT personnel, it is for employers of such personnel to decide how to assure themselves that they are competent to do the work assignments. Thus, they may employ people who are already certiied or they may apply their own expertise so as to assure themselves that their employee has the necessary competence. In this last case, prudent employers would no doubt use this document as a reference document.
© ISO 2021 – All rights r eserved
vii
INTERNATIONAL ST STANDARD ANDARD
ISO 9712:2021(E)
Non-destructive ve testing — Qualiication and certiication of Non-destructi NDT personnel 1
Scope
This document speciies requirements for the qualiication and certiication of personnel who perform industrial non-destructive testing (NDT) in the following methods. a)
acou ac ousti sticc emis emissi sion on tes testin ting; g;
b)
eddy ed dy cu curr rren entt tes testin ting; g;
c)
leak testing (hyd (hydrau raulic lic pre pressur ssure e tests tests exclu excluded ded); );
d) ma magn gnet etic ic te test stin ing; g; e)
pen pe net etra ran nt te testi sting ng;;
f)
radi ra dio ogr gra aphi hicc tes testi ting ng;;
g) stra strain in ga gaug uge e test testin ing; g; h) th ther erm mog ogra raph phic ic tes testin ting; g; i)
ultr ul tras aso oni nicc tes testi tin ng;
j)
visual testing testing (direct (direct unaid unaided ed visual tests tests and visual visual tests carried carried out out during during the appli applicatio cation n of another NDT method are excluded).
The system speciied in this document is also applicable to other NDT methods or to NDT techniques within an established NDT method, provided a comprehensive scheme of certiication exists and the NDT method or NDT technique is covered by international, regional or national standards or the NDT method or the NDT technique has been demonstrated to be effective to the satisfaction of the certiication body. NOTE 1
The term "indust "industrial rial"" implies the exclusion of applications in the ield of medicine.
NOTE 2
CEN/TR 14 14748 748 provides guida guidance nce on the methodology for quali ication of non-destruct ive test tests. s.
NOTE 3 This document document speciies requirements requirements for what are, in effect, third party conformity conformity assessment assessment schemes. These requirements do not directly apply to conformity assessment by second or irst parties, but relevant parts of this document can be referred to in such arrangements. NOTE 4 The term “direct unaided visual testing” implies implies where there is an uninterrupted optical path path from the observer’s eye to the test area and the observer uses no tools or devices (e.g. mirror, endoscope, ibre optic). NOTE 5
2
Calculat ions of stra strain in based on other NDT methods are excluded.
Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest lat est edition edit ion of the referenced document (including any amendments) amendments) applies. ISO/IEC 17 17024:2012, 024:2012, Conformity assessment — General requirements for bodies operating certiication of persons
© ISO 2021 – All rights r eserved
1
ISO 9712:2021(E)
te sting — Evaluation of vision acuity of NDT personnel ISO 18490:2015, Non-destructive testing
3
Terms and deini deinitions tions
For the purposes of this document, the following terms and deinitions apply. ISO and IEC maintain terminology databases for use in standardization at the following addresses: https://www www.iso .iso.org/ .org/obp obp — ISO Online browsing platform: available at https://
— IEC Electr Electropedia: opedia: available at https:// https://www www.electropedia .org/ .org/ 3.1 applicant person who has submitted an application to be admitted into the certiication process ( process (3.8) 3.2 authorized qualiication body employer loyer (3.11), authorized by the certiication body (3.6) to prepare and body, independent of the the emp examinations ( (3.12 3.12)) administer examinations 3.3 basic examination element written examination examination (3.12), at Level 3, which demonstrates the candidate’s candidate’s (3.4) knowledge of the qualiication ( (3.33 3.33)) materials science and process technology and types of discontinuities, the speciic qualiication methods (3.25 3.25) as required for Level 2 and certiication system, and the basic principles of NDT methods ( Note 1 to entry: For an explanation of the three levels of qualiication, see Clause 6. Note 2 to entry: The qualiication quali ication and certiication system is speciied in this document.
3.4 candidate applicant (3.1) who has fulilled speciied prerequisites and has been admitted to the certiication process ( process (3.8) 3.5 certiicate documen docum entt in the form of a letter, card or other medium (e.g. digital certiicate), issued by a certiication body (3.6) under the provisio prov isions ns of this document, indicating that the named person has fulilled the certiication requirements ( requirements (3.9 3.9)) 3.6 certiication body body that administers procedures for certiication according to speciied requirements 3.7 certiication cycle maximum period of time time permitted permitted from the date of certiication to the date of recertiication recertiication (3.34) inclusive of the renewal (3.36 (3.36)) period 3.8 certiication process ( 3.6) determines that a person fulils tiication requirement requirement s acti ctivities vities by which a certiication body (3.6 fulil s cer tiication (3.9), including applicatio application, n, assessment, decision on certiication, renewal (3.36), recertiication recertiication ( ( 3.34) and use of certiicates certiicates ( (3.5 3.5 ) and logos logos/marks /marks 3.9 certiication requirements set of speciied requirements, including requirements of the scheme to be fulilled in order to establish or maintain certiication 2
© ISO 2021 2021 – All rights re served
ISO 9712:2021(E)
3.10 competence ability to apply knowledge and skills to achieve intended results 3.11 employer candidate ( (3.4 legal entity by whom the candidate 3.4)) is employed Note 1 to entry: A candidate may be self-employed.
3.12 examination mechanism that is part of the assessment which measures a candidate's candidate's ( (3.4) competence competence ( (3.10 3.10) by one or more means 3.13 examination centre (3.6)) where examinations examinations ( (3.12 3.12) are carried out centre approved by the certiication body (3.6 3.14 examination element examination ( (3.12 3.12)) component of an examination 3.15 examiner person competent to conduct and score an examination examination (3.12), where the examination requires professional judgem judgement ent 3.16 general examination examination element element written examination examination ( (3.12 3.12), at Level 1 or Level 2, concerned with the (3.25)) t he principles of an NDT method (3.25 3.17 higher education formal learning that occurs after completion of secondary education in the ield of engineering or science 3.18 industrial experien experience ce work activities ( activities (3.46) performed under supervision supervision ( (3.45 3.45), ), in the NDT method (3.25 (3.25)) in the sec sector tor (3.37 (3.37)) qualiication ( (3.33 3.33)) concerned, needed to acquire the skill and knowledge to fulil the provisions of qualiication 3.19 invigilator proctor test administrator person authorized by the the cer tiication tiication body (3.6) who supervises an examination examination (3.12), but does not competence ( (3.10 3.10)) of the candidate candidate ( (3.4) evaluate the competence 3.20 job-speciic training certiicate (3.5 ) holder in aspects of training, provided by the employer (3.11) (or their agent) to the certiicate non-destructive testing speciic to the employer’s products, NDT equipment, NDT procedures procedures (3.27 ), speciications ( (3.40 and applicable code codes, s, standards, speciications 3.40)) and procedures, leading to the award of operating authorizations ( authorizations (3.30 3.30)) 3.21 main method examination element written examination examination (3.12), at Level 3, which demonstrates the candidate’s candidate’s (3.4 3.4)) general and speciic knowledge, and the ability to write NDT procedures ( procedures (3.27 3.27)) for the NDT method (3.25 ( 3.25) as applied in the sector(s) ( (3.37 3.37) for which certiication is sought industrial or product sector(s) © ISO 2021 – All rights r eserved
3
ISO 9712:2021(E)
3.22 multiple choice examination question wording of a question giving rise to potential replies, only one of which is correct, the remaining being incorrect or incomplete 3.23 NDT instruction written description of the precise steps to be followed in testing to an established standard, code, speciication ( speciication (3.40) or NDT procedure ( procedure (3.27 3.27)) 3.24 NDT media testing products used to create visible indications caused by imperfections or laws EXA MPLE
Magnetic powder powder,, contrast aid paints paints,, colour contrast penetrant, developer developer..
3.25 NDT method discipline applying a physical principle in non-destructive testing EXAMPLE
Ultrasonic testing.
3.26 NDT personnel personnel who perform non-destructive testing 3.27 NDT procedure written description of all essential parameters and precautions to be applied applied when when non-destructively testing test ing products in accordance with sta standard(s ndard(s), ), code(s) code(s) or speciication(s) speciication(s) ( (3.40) 3.28 NDT technique speciic way of utilizing an NDT method (3.25 (3.25)) 3.29 NDT training process of instruction in theory and practice in the NDT method (3.25 (3.25) in which certiication certiication is is sought, (3.6)) which takes the form of training courses to a syllabus approved by the certiication body (3.6 3.30 operating authorization (3.11), based upon the scope of certiication, authorizing the written statement issued by the employer (3.11 individual individu al to carry c arry out speciied tasks Note 1 to entry: Such authorization can be dependent on the provision of job-speciic training ( training (3.20 3.20). ).
3.31 practical examination element candidate (3.4 assessment of practical skills, in which the candidate 3.4)) demonstrates familiarity with, and the ability to perform, the test 3.32 psychometric process statistical proces processs to verify examinations examinations ( (3.12 3.12) are fair, reliable and discriminate between a competent and non-competent individual 3.33 qualiication demonstrated education, training, and work experience
4
© ISO 2021 2021 – All rights re served
ISO 9712:2021(E)
3.34 recertiication process for revalidation of a certiicate certiicate (3.5 ) by examination examination (3.12) or by otherwise satisfying the certiication body (3.6 (3.6) that the published criteria for recertiication have been met 3.35 referee individual individu al that attests attest s the validity of the candidate’s candidate’s ( (3.4) industrial experience ( experience (3.18) 3.36 renewal process for revalidation of a certiic certiication ation at any t ime ime up to ive years after success in an initial, supplementary supplem entary or recertiication recertiication ( (3.34) examination examination ( (3.12 3.12)) 3.37 sector section of industry or technology where specialized NDT practices are used, requiring speciic productrelated knowledge, skill, equipment or training Note 1 to entry: A sector can be interpreted to mean a product (welded products, castings) or an industry (aerospace, in-service testing). See Annex A .
3.38 signiicant interrupti interruption on
absence or change of work 3.46) 3.46 ) which and prevents the cert iied) individual iied practising sector(s) ( (3.37 3.37 duties corresponding to theactivity level in (the method the sector(s) within thefrom certiied scope, the for either a continuous period in excess of one year, or two or more periods for a total time exceeding two years Note 1 to entry: Legal holidays or periods of sickness or training courses of less than 30 days are not taken into account when calculating the interruption.
3.39 speciic examination ele examination element written examination 3.12 2), at Level 1 or Level 2, concerned with testing techniques applied in a examination (3.1 sector(s tor(s ) ) (3.37 ), including knowledge of the product(s) tested and of codes, standards, particular sec speciications ( speciications (3.40 3.40), ), procedures and acceptance criteria 3.40 speciication document stating requirements 3.41 specimen sample used in practical examinations examinations (3.12), possibly including radio radiographs graphs and data sets, which is (3.37)) representative of products typically tested in the applicable sector (3.37 Note 1 to entry: A specimen can include more than one area or volume to be tested.
3.42 specimen master report model answer, indicating the optimum result for a practical exa examination mination (3.12) given a speciied set specimen ( ( 3.41 candidate’s of conditions (equipment type, settings, technique, specimen 3.41), ), etc.) against which the candidate’s (3.4 3.4)) test report is graded 3.43 structured credit system candidate (3.4 examination point system based on the NDT activities of the candidate 3.4)) used as an alternative to examination (3.12 3.12)) for renewal (3.36 (3.36)) or recertiication recertiication ( (3.34)
© ISO 2021 – All rights r eserved
5
ISO 9712:2021(E)
3.44 structured experien experience ce program SEP (3.6)) to reduce industrial experience ( experience (3.18) program approved by the certiication body (3.6 3.45 supervision act of directing the application of NDT performed by other NDT personnel (3.26), which includes the
control of actions involved in the preparation of the test, performance of the test and reporting of the results 3.46 work wor k activity activit y performance of NDT-related functions and tasks Note 1 to entry: See Clause 6.
4
Abbreviated terms
For the purposes of this document, the abbreviated terms listed in Table 1 1 are used to identify NDT methods. Table 1 — Methods and abbreviated terms NDT method
Abbreviated Abbreviate d terms
Acoust ic emission test ing
AT
Eddy current testing Leak testing
ET
LT
Mag net ic testing
MT
Penet rant testing
PT
Radiographic Radiograp hic testing t esting
RT
Strain gauge testing
ST
Thermographic Thermograp hic testing
Ultrasonic testing V i s u a l t e s t i ng
TT UT
VT
5 Responsibilities 5.1 General The certiication system, which shall be controlled and administered by a certiication body, includes all procedures necessary to demonstrate the qualiication and the competence of an individual to carry out tasks in a speciic NDT method and product or industrial sector, leading to certiication.
5.2
Certiication body
5.2.1
The certiication body shall fulil the requirements of ISO/IEC 17024.
5.2.2
The certiication body:
a)
shall initiate, promo promote, te, maintain and administer administer the certiication certiication scheme scheme according according to ISO/IEC ISO/IEC 170 17024 24 and this document;
b)
shall be inde indepen pende dent nt of of any any single single intere interest; st;
6
© ISO 2021 2021 – All rights re served
ISO 9712:2021(E)
c)
shall be be respons responsib ible le for for the deiniti deinition on of of sectors sectors (see (see Annex A); A);
d) shall publish publish information information regarding regarding the scope scope of of the certiication scheme scheme and and a general general description description of the certiication process; e)
shall provide provide information information for for training courses courses that includ include e the syllabi which which embody embody the content content of of recognized documents; ISO/TS 2510 25107 7 or equivalent can be used as guidance; g uidance;
f)
shall conduct condu ctbody(ies) an initial audit and audit subsequen uentt periodic peri odic surveillance audi audits ts of the authorized authorized qualiication to ensure theirsubseq conformity to the speciications;
g) shall monitor monitor,, in accordan accordance ce with a documen documented ted procedur procedure, e, all delega delegated ted functions; functions; h) shall approv approve e properl properly y staffed and equippe equipped d examination examination centres, which it shall shall monitor monitor on on a periodic basis; i)
shall admini administer ster examin examinatio ations ns through through app approv roved ed examinati examination on centres centres;;
j)
shall bear bear full respons responsibilities ibilities for examinations cond conducted ucted on tempo temporary rary basis at at external premis premises; es;
k) shall be respons responsible ible for ensuring the security of all examination examination materials (examinatio examination n specimens, specimens, specimen master reports, question banks, examination papers, etc.) and shall ensure that these materials are not in use for training purposes; l)
shall be responsi responsible ble for granting, extension, extension, suspensio suspension, n, withdrawal withdrawal or or revalidatio revalidation n of of certi certiication ication;;
m) shall establish an approp appropriate riate system for the maintenance maintenance of of records, records, which shall be retained for for at least one certiication cycle; n)
shall require require all candidates candidates and certiicate certiicate holders holders to give a signed signed or stamped undertaking undertaking to abide by a code of ethics which wh ich it shall develop for for the purpose and a nd publish;
o)
may appro approve ve training bodies bodies;; ISO/TS ISO/TS 2510 25108 8 can be used as guidance guidance;;
p)
may delega delegate, te, under under its direct direct responsibility responsibility,, the detailed detailed administration administration of qualiicatio qualiication n to authorized qualiication bodies, to which it shall issue speciications and/or procedures covering facilities, personnel, veriication and control of NDT equipment, examination materials, specimens, conduct of examinations, examination grading, records, etc.;
q) shall estab establish lish a proce process ss to au autho thorize rize examin examiners ers;; r)
shall establish establish the cond conditions itions for the supervision supervision of wor work k activities, which which candidates candidates may claim claim experience under 7.3;
s)
shall establ establish ish a proce process ss for for the recognitio recognition n of higher higher edu educatio cation; n;
t)
shall establish establish a proce process ss for for the app approval roval of of non-ce non-certiied rtiied individuals individuals as a refere referee; e;
u)
shall establish establish a process process for for the app approval roval of of a structured credit credit system, where where used;
v) may specify specify a minimum minimum age age requirem requiremen entt for candid candidates ates unde underr 7.1; w) shall maintain and and update update the question question bank and the examination examination specimens specimens along along with their specimen master report; x)
shall conduct conduct the examination examination only only in the presenc presence e of, and and under under the control control of, of, an authorized authorized invigilator of the certiication body, to ensure that impartiality is maintained;
y) shall establish establish a process process for for the app approval roval of of a structured experien experience ce program, program, where where used.
© ISO 2021 – All rights r eserved
7
ISO 9712:2021(E)
5.3
Authorized qualiication body
Where established, the authorized qualiication body shall: a)
work wor k under under the contro controll of and appl apply y the speciications speciications issued issued by the certiication body; body;
b)
be indepe independ nden entt of any singl single e predomi predominan nantt interest; interest;
c)
ensure that it is impartial impartial with respect to each each candidate candidate seeking seeking qualiication qualiication,, bringing to the attention of the certiication body any actual or potential threat to its impartiality;
d) app apply ly a docume documented nted quality quality managemen managementt system appro approved ved by by the certiication certiication body; e)
have the resources resources and and expertise expertise necessary to establish, monito monitorr and contro controll examinations examinations centres, centres, including examinations and the veriication and control of the equipment;
f)
conduct cond uct qualiication qualiication of of candidates candidates inclu including ding review review of app application lication and decision decision on eligibility; eligibility;
g) pre prepare pare,, supervise supervise and admi administe nisterr examina examination tions; s; h)
provide the certiication provide certiication body body with the results of of qualiication qualiication needed needed to make a decision decision on certiication by the certiication certi ication body; body;
i)
maintain approp appropriate riate qualiication qualiication and examination records acco according rding to the require requiremen ments ts of the certiication body.
5.4
Examination centre
5.4.1
The examination centre shall:
a)
work wor k under under the contro controll of the certiication body or or authorized authorized qualiication qualiication body; body;
b)
apply app ly a docum documented ented quality procedu procedure re approv approved ed by the certiication body;
c)
have the resou resources rces needed needed to prepare prepare and cond conduct uct examinations, examinations, inclu including ding the veriication veriication and control of equipment;
d) have adequ adequate ate qualiied qualiied staff, premises premises and and equipme equipment nt to ensure satisfactory satisfactory examinations examinations for for the levels, methods, and sectors concerned; the use of external premises is allowed; e)
prepare prep are and condu conduct ct examinations unde underr the responsibility responsibility of an examiner examiner authorized authorized by the certiication body, using examination by the certiication body only for that purpose; questionnaires and specimens established or approved
f)
maintain appro appropriate priate examination docum documents ents accordin according g to the requireme requirements nts of of the certiication body.
5.4.2 An examination centre may operate within the certiication body; or within an authorized qualiication body; or be an independent legal entity or part of a legal entity. An examination centre can be situated at an employer’s premises. In this case, the certiication body shall require controls to preserve impartiality and protect conidentiality of the examinations. The examinations shall be conducted only in the presence of, and under the control of, an authorized representative of the certiication body.
5.5
Employer
5.5.1 The employer shall document the personal information which shall include the declaration of education, training and industrial experience and visual acuity needed to determine the eligibility
8
© ISO 2021 2021 – All rights re served
ISO 9712:2021(E)
of the candidate. If the candidate is self-employed, the industrial experience shall be attested to by a referee. All documentation obtained from the employer shall be veriied by the certiication body. 5.5.2
In respect of certiied NDT personnel under their control the employer shall be responsible for:
a)
all that concerns concerns the authorization authorization to operate, operate, i.e. i.e. providing providing job-speciic job-speciic training (if necessary) necessary);;
b)
issuing issui ng the written written autho authorizati rization on to oper operate ate;;
c)
the th e resu results lts of ND NDT T acti activit vitie ies; s;
d) ensu ensuring ring that the the annual annual visio vision n require requireme ments nts of of 7.4 .4 are are met; e)
maintaining docume documentary ntary evidence evidence conirming conirming the continu continuous ous appli application cation of of the NDT NDT method method in the relevant sector(s) without signiicant interruption; this action shall be done every 12 months;
f)
ensuring ensu ring that perso personne nnell hold hold valid certiicatio certiication n relevant relevant to their their tasks within the organizati organization on;;
g) mai maintai ntainin ning g appr approp opria riate te reco records rds.. These responsibilities shall be described in a documented procedure. 5.5.3
A self-employed individual shall assume all responsibilities ascribed to the employer.
5.5.4 Certiication to this document provides an attestation of general competence of the certiied NDT personnel. It does not represent an authorization to operate, since this remains the responsibility of the employer; and the certiied NDT personnel may require additional specialized knowledge of parameters such as equipment, NDT procedures, materials and products speciic for the employer.
Where required by regulatory requirements and codes, the authorization to operate shall be given in writing by the employer in accordance with a quality procedure that speciies any employer-required job-speciic training and examinations designed to verify the certiicate holder's knowledge of relevant industry code(s), standard(s), NDT procedures, equipment, and acceptance criteria for the tested products.
5.6 Candidate Candidates shall: a)
provide pro vide docum documentary entary evide evidence nce of of training training in accordan accordance ce with 7.2;
b)
provide provid e documentary documentary evidence evidence that the required required experience experience has been gained under under supe supervision; rvision;
c)
provide pro vide docum documentary entary eviden evidence ce of vision vision satisfying the require requireme ments nts of 7.4 .4;;
d) abid abide e by a code code of of ethics pub published lished by the certiication body; body; e)
5.7
provide pro vide other other requis requisites ites requ requested ested by by the certiication certiication body body..
Certiicate holders
Certiicate holders shall: a)
abide ab ide by by a code code of ethics ethics pub publish lished ed by the the certiicatio certiication n body; body;
b)
maintain records records demo demonstrating nstrating evidence evidence that vision requirem requirements ents have have been been fulilled in accordance with 7.4 .4;;
© ISO 2021 – All rights r eserved
9
ISO 9712:2021(E)
c)
notify the certi certiication ication body and the emp employ loyer er if the conditions conditions of certiication are not maintained (see 9.3 9.3). ).
5.8 Examiners 5.8.1
Examiners shall:
— be authorized by the certiication certiic ation body to conduct, conduct, supervi supervise se and grade examinat examinations; ions; — be certi certiied ied to Level 3 in the NDT method in the product and/o and/orr industrial sector for which they are authorized. 5.8.2
An examiner shall not be permitted to examine any candidate:
— that they have trained for the examination examinat ion for a period of of two years from the date of the conclusion of the training; — who is working (permanently or temporarily) in the same facility as the examiner unless the certiication body has established a documented conidentiality and impartiality management procedure for such a situation.
5.9 Referee A referee shall be: a)
certiied certiie d to Lev Level el 2 or or 3 in any any NDT NDT metho method; d; or
b)
non-certiied personnel non-certiied personnel who, who, appro approved ved by the certiication certiication body, body, possess possess the knowledge, knowledge, skill, skill, training and experience required to attest to the candidate’s industrial experience.
6
Levels of certiication
6.1
Level 1
6.1.1 An individual certiied to Level 1 has demonstrated competence to carry out NDT according to written instructions and under the supervision of Level 2 or Level 3 personnel. Within the scope of the competence speciied on the certiicate, Level 1 personnel may be authorized by the employer to
perform the following in accordance with NDT instructions: a) se sett up up NDT NDT eq equi uipm pmen ent; t; b)
perf pe rfo orm th the e tes tests ts;;
c)
record reco rd and and classify classify the resul results ts of the the tests acco accordin rding g to written written criteria; criteria;
d) rep report ort the resul results. ts. 6.1.2 Level 1 certiied personnel shall neither be responsible for the choice of test method or technique to be used, nor for the interpretation of test results.
6.2
Level 2
An individual certiied to Level 2 has demonstrated competence to perform NDT according to NDT procedures NDT instructions. the yer scope 2 personnel or may be authorized byWithin t he employer the emplo to: of the competence speciied on the certiicate, Level a)
10
select sel ect the NDT NDT techniq technique ue for for the the testing testing method method to be used used;;
© ISO 2021 2021 – All rights re served
ISO 9712:2021(E)
b)
specify spec ify the limitatio limitations ns of app applica lication tion of of the testing testing method method;;
c)
translate NDT NDT codes, codes, standards, speciications, speciications, and proced procedures ures into into NDT instructions adapted adapted to the actual working conditions;
d) set up and ve verify rify equi equipm pmen entt settings settings;; e)
perfo pe rform rm an and d su supe pervise rvise tes tests; ts;
f)
interpret and evaluate results accor interpret according ding to appli applicable cable standards, codes, codes, speciications or procedures;
g) carry out out and and supervise supervise all tasks tasks at or or belo below w Level Level 2; 2; h) provid provide e guidance guidance and mento mentoring ring for perso personnel nnel at at or below below Level 2; 2; i)
6.3
report rep ort the resul results ts of NDT NDT..
Level 3
6.3.1 An individual certiied to Level 3 has demonstrated competence to perform and direct NDT operations for which they are certiied. Level 3 personnel have demonstrated:
a) b)
c)
the compete competence nce to evaluate evaluate and and interpret interpret results results in terms of of existing standards, codes, codes, and speciications; suficient practical practical knowledge knowledge of of applicabl applicable e materials, fabrication, fabrication, process, process, and and product product technology technology to select NDT methods, establish NDT techniques, and assist in establishing acceptance criteria where none are otherwise available; a gen general eral famil familiarity iarity with with other other NDT meth methods ods listed in Clause 4.
6.3.2 Within the scope of the competence speciied on the certiicate, Level 3 personnel may be authorized by the t he employer employer to:
a)
establish, review for editorial and technical correctness, correctness, and validate NDT instructions and and procedures;
b)
interpre inte rprett standards, standards, codes, codes, speciicati speciications ons,, and proced procedures ures;;
c)
designa des ignate te the particular particular test metho methods, ds, proce procedur dures, es, and NDT NDT instruction instructionss to be used; used;
d) carry out out and and su supervise pervise all tasks tasks at all leve levels; ls; e)
provide provid e guidance guidance and and mento mentoring ring for for NDT perso personnel nnel at all leve levels. ls.
7
Eligibility
7.1 General The candidate shall fulil fu lil the t he minimum requirements of vision and NDT trai training ning prior to the examination and shall fulil the minimum requirements for industrial experience and, where applicable, has reached a minimum age as speciied by the certiication body prior to certiication.
7.2
Training
7.2.1 The candidate shall provide documentary evidence, acceptable to the certiication body, that he or she has satisfactorily completed NDT training as shown in Table 2 in 2 in the method and level for which the certiication is sought. © ISO 2021 – All rights r eserved
11
ISO 9712:2021(E)
7.2.2 For all levels, theoretical training may be delivered in a face-to-face instructor-led format, distance learning format, a self-paced format, or a combination of these formats. Practical training shall be delivered by a face-to-face instructor-led format only. The training for initial certiication shall remain valid for a maximum period of ten years from the date of completion.
For Level 3, in addition to the minimum training requirements given in Table 2, 2, the preparation for qualiication can be completed in different ways dependent on the scientiic and technical background of the candidate, including attendance at other training courses, conferences or seminars, studying books, periodicals and other specialized printed or electronic materials. When a distance learning option is utilized, systems shall be established to ensure the entire training syllabus is completed. NOTE
Guidelines for NDT personnel trai training ning organiz organizations ations are given in ISO/TS 251 25108 08
7.2.3 The minimum duration of training undertaken by the candidate for certiication shall impart the skills and knowledge and shall not be less than that speciied in 7.2.4 7.2.4 and and Table 2 for 2 for the applicable NDT method, with the possible reductions speciied in 7.2.5 7.2.5..
This duration is based upon candidates possessing mathematical skills ski lls and prior knowledge knowledge of material materialss and processes that can be conirmed by appropriately screening of completed prior education. If it is not the case, additional training on this matter may be required by the certiication body. Training days include both practical and theoretical courses. When creating industrial sectors as speciied in Annex A, A, the certiication body shall consider the minimum training requirements in Table 2. 7.2.4
Direct access to Level 2 requires the total days shown in Table 2 for 2 for Levels 1 and 2.
Direct access to Level 3 requires the t he total days shown in Table 2 for 2 for Levels 1, 2, and 3. When considering the responsibilities of a certiied Level 3 (see 6.3) and the content of item C of the basic examination element for Level 3 (see Table 5), 5), additional training about the other NDT methods may be necessary. Table 2 — Minimum training requirements Level 1
Level 2
Level 3
daysa
daysa
daysa
AT
5
8
ET
5
6
6
LT
5
9
6
NDT method
5
MT
3
2
4
PT
3
2
3
RT b
5
10
5
ST
2
3
2
TT
5
6
5
UT
8
10
5
2
3
VT
3
a
One day duration is at least seven hours, which can be achieved on a single day or by accumulating hours. b
For RT, trai training ning days does not include radiation safet safety y trai training. ning.
NOTE 1 In the case of speciic techniques, see Annex F.
7.2.5 The possible reductions in training duration are as described hereafter, provided that, when several reductions are applicable, the total reduction does not exceed 50 % of the training duration. 12
© ISO 2021 2021 – All rights re served
ISO 9712:2021(E)
Any reduction requires acceptance by the certiication body and shall ensure that competence is maintained. a)
For al alll lev eve els ls:: — for candidates seeking certiicat certi ication ion in more than one method method (i.e. MT, MT, PT), or for those already certiied and seeking certiication in another method, when the training syllabus concerned duplicates certain aspects (i.e. product technology), the total number of training days for these methods (i.e. PT, MT, VT) may be reduced in line with the training syllabus; — for candidates who have graduated in a relevant subject from technical college or or university, or or have completed completed at least two t wo years of relevant engineering or science study at college or or university (or equivalent formal education), the total required training duration may be reduced by up to 50 %; the certiication body shall specify relevant subjects and their qualiication.
b)
For Levels 1 and 2, For 2, when the scope scope of activity is limited in application application and/ and/or in technique technique (and (and not not covered in Annex F), F ), the training scope and duration may be reduced by up to 50 %.
NOTE Examples of such limit limitations ations include those related to application (e.g. automated ET, UT of bar, tube, and rod or normal beam ultrasonic thickness and lamination testing of rolled steel plate) and to technique (e.g. leak testing only using bubble test, yoke for magnetic particle).
7.3
Industrial NDT experience
7.3.1
General
The minimum duration of industrial experience to be gained in the method where the candidate is 7.3.3.. When the seeking certiication shall be as given in Table 3, 3, with the possible reductions given in 7.3.3 candidate is seeking certiication in more than one method, the total time of experience shall be the sum of the experience in each method. For all levels, a minimum period of experience prior to examination shall be speciied by certiication body (a fraction or percentage of the total requirement in Table 3, 3, as appropriate). In the event that a part of the experience is sought following successful examination, the results of the examination shall remain valid for a maximum of ive years. Documentary evidence of experience shall be conirmed by the employer or the referee and submitted to the certiication body. Table 3 — Minimum industrial experience Experience Experience in daysa NDT method
Level 1
AT, ET, LT, RT,
45
TT, UT MT, PT, ST, VT
Level 2
15
Level 3
with Level 1
direct access
135
180
45
60
higher education, with Level 2
with Level 2
direct access with higher education
270
450
540
180
240
360
a
One day duration is at least seven hours, which can be achieved on a single day or by accumulat ing hours. The maximum allowable hours in any one day is 12 hours. Experience in days is achieved by dividing the total accumulated hours by 7.
7.3.2
Level 3
Level 3 responsibilities require knowledge beyond the technical scope of any speciic NDT method. This broad knowledge may be acquired through a variety of combinations of education, training and experience. Table 3 details 3 details minimum m inimum experience for candidates who have successfully completed higher education, as well as candidates without higher education.
© ISO 2021 – All rights r eserved
13
ISO 9712:2021(E)
7.3.3
Possible reductions
7.3.3.1 The possible reductions in duration of experience are as described hereafter. Any reduction shall require acceptance by the certiication body. 7.3.3.2 A certiied Level 1, 2 or 3 adding an additional method may be permitted a reduction of required experience of 25 % for that additional method. 7.3.3.3 A certiied Level 1, 2 or 3 individual changing sector, adding another sector or technique for the same NDT method shall be required to gain additional experience of at least 25 % of the experience required in Table 3; 3; and this shall never be less than 15 days in duration. 7.3.3.4 When the scope of certiication sought is limited in application (i.e. thickness measurement or automated testing), experience duration may be reduced by up to 50 % but shall not be less than 15 days. 7.3.3.5 Up to 50 % of the industrial experience time may be achieved by a structured experience program (SEP). One day of att attendance endance at the SEP may be equivalent to a maximum maxi mum of ive days industrial industria l experience. The SEP shall include all typical tasks (see Clause 6) 6) of the level, method and sector concerned. The additional intent is to gain speciic product and technique knowledge. The SEP shall be approved in advance by the certiication body and shall be available for audit by the certiication body.
7.4 7.4.1
Vision requirements — all levels General
Candidates and certiicate holders shall maintain and provide documentary evidence of acceptable vision in accordance 7.4.2 to 7.4.4. 7.4.2
Near vision acuity
Prior to certiication, and annually thereafter, near vision acuity shall be veriied to be in accordance with the requirements of ISO 18490 or shall permit reading a minimum of Jaeger number 1 or Times Roman N4.5 or equivalent letters at not less than 30 cm with one or both eyes, either corrected or uncorrected. 7.4.3
Colour vision
Prior to certiication, recertiication or renewal, the candidate/certiicate holder shall demonstrate that a colour vision test has been administered within the previous 5 calendar years. It is required that colour vision and/or grey scale perception be suficient for the individual to be able to distinguish and differentiate between the colours or shades of grey used in the NDT methods/ techniques concerned as speciied spec iied by the t he employer employer.. The colour vision test shall either conirm that the individual has acceptable colour vision without restriction or shall state any limitation(s) on colour perception. Where any limitation in colour perception exists, the employer shall conirm whether or not this condition results in any limitation(s) to method or application speciic techniques. NOTE
14
The Ishihar Ishihara a 24 plate test is an example of a suitable colour vision test test..
© ISO 2021 2021 – All rights re served
ISO 9712:2021(E)
7.4.4
Personnel administering vision tests
Near vision acuity testing, colour vision and/or grey scale perception veriication(s) shall be administered by a licensed physician, nurse, ophthalmologist or optometrist; or by another trained professional who is approved and documented by a Level 3 personnel acting ac ting on behalf of the t he employer. employer.
8 Examinations 8.1 Overview 8.1.1
General
The examination shall cover an NDT method, technique, industrial sector and/or product sector as appropriate. The process used for the development and selection of examination questions shall be speciied in a procedure prepared by the certiication body. It shall ensure the questions are appropriate for the relevant syllabus for the method/technique/sector, and for the level of certiication. The process shall be designed to ensure the comparability of results of examinations using methods such as peer group review, input from subject matter experts, statistical comparisons, and, where the size of the examination cohort allows, psychometric principles may be used as speciied in Annex G. The certiication body shall establish a documented appropriate methodology and procedures to ensure fairness, validity, reliability, and general performance of examinations to maintain an acceptable pass grade of 70 % for all examinations. The processes for preparation and conduct of examinations examinat ions (see (see 8.4 8.4)) shall further furt her be designed designed to ensure the conidentiality and security of examination questions and examination papers. The practical specimens shall be maintained and monitored to ensure consistency and fairness of examinations using processes adopted by the certiication body. The results of examinations shall remain valid for up to ive years while the candidate completes any remaining certiication requirements. 8.1.2
Examination elements
For Level 1 the examination shall consist of the following examination elements: — general examinat examination ion element; — speci speciic ic examination examinat ion element; — practica practicall examinat examination ion element. For Level 2 the examination shall consist of the following examination elements: — general examinat examination ion element; — speci speciic ic examinat examination ion element; — practica practicall examinat examination ion element; — NDT inst instruction ruction writ writing ing elemen element. t. For Level 3 the examination shall consist of the following examination elements: — basic examination elemen elementt which consist consistss of the following following items: — item A technica technicall knowledge; — item B certi certiicat ication ion body's document knowledge; © ISO 2021 – All rights r eserved
15
ISO 9712:2021(E)
— item C Level 2 knowledge of methods; — main method examinat examination ion element which consists of of the following following items: — item D general examinat examination; ion; — item E speci speciic ic examinat examination; ion; — item F NDT procedures. 8.1.3
Examination time
The certiication body shall specify and publish the maximum amount of time allowed for the candidate to complete each examination element, which shall be based upon the following. For Level 1 and Level 2, the total time for the examination elements shall be based on two minutes per multiple choice examination question for general examination element and three minutes per multiple choice examination question for speciic examination element. For Level 3, the total time for the examination elements shall be based on three minutes per multiple choice examination question in items B and E and two minutes for items A, C and D. For questions requiring narrative answers, Level 3 item F, NDT instruction writing element, and for the practical examination element, the time allowed shall be determined by the certiication body. 8.1.4
Examination aids
The use of aids such as codes, standards, speciications, procedures and electronic devices is only permitted if supplied as part of the examination or authorized by the certiication body.
8.2 8.2.1
Examination content and grading for Level 1 and and Level Level 2 General examinat examination ion element
The general examination element shall be a minimum of 40 multiple choice examination questions and shall be selected randomly from the certiication body’s or authorized qualiication body’s collection of general examination element questions valid at the date of examination. Where not otherwise addressed by national regulations, there may be an additional examination on radiation safety for the radiographic testing method. 8.2.2
Speciic examination element
The speciic examination element shall be a minimum of 20 multiple choice examination questions selected from the certiication body’s or authorized qualiication body’s collection of speciic examination element questions valid at the date of examination. If the speciic speci ic examination examinat ion element element covers two or more more sectors, the t he minimum number of of questions shall be at least 30, taking into account the industrial or product sectors concerned (see Annex A). 8.2.3
Practical examinat examination ion element
8.2.3.1 The practical examination element shall involve applying the test to prescribed specimens, recording (and, for Level 2 candidates, interpreting) the resulting information to the degree required, and reporting the results in the required format. Specimens used for training purposes shall not be used for examination. 8.2.3.2 Each specimen shall be uniquely identi identiied ied and have a specimen master report which wh ich includes all of the equipment settings (if applicable) used to detect speciied discontinuities. Markings shall not 16
© ISO 2021 2021 – All rights re served
ISO 9712:2021(E)
interfere with the practical testing or inspection of the specimen and shall, wherever practicable, be concealed from the candidate while the specimen is being used for examination to prevent potential information correlation by candidates. The specimen master report shall be compiled based upon at least two independent tests, and shall be veriied by a Level 3 certiicate holder in that method for use in grading examinations. The independent test reports from which the specimen master report is compiled shall be retained as records. 8.2.3.3 Specimens shall be sector (one or more) speciic, representing ield geometries and They shall contain discontinuities representative of those likely to occur during manufacturing or in service. may be natural or artiicial. Data sets, digital radiographic images and/or ilms can be used instead of physical specimens, but at least one physical specimen shall be examined.
Specimens used for adjustment or for determination of thickness, coating or material properties do not need to contain discontinuities. discont inuities. For RT, RT, the specimens speci mens to be tested do not need to contain discontinuities discontinuit ies if these are exhibited in the data sets or radiographic images for Level 2 interpretation. NOTE
Guidelines on discontinuit discontinuity y ty types pes in exami examination nation specimens can be found in ISO/TS 22809.
8.2.3.4 The certiication body shall ensure that the number of specimens to be tested is adequate to the level, NDT method and sector concerned, and that the specimens contain reportable report able discontinuities. The number of specimens to be tested in the Level 1 and Level 2 practical examinations shall be in accordance with Annex B. 8.2.3.5
The Level 1 candidate shall follow the NDT instruction(s) provided by the examiner.
8.2.3.6 The Level 2 candidate shall select the applicable NDT technique and determine the operating conditions related to a given code, standard or speciication. 8.2.3.7 8.2.4
The time allowed for the examination shall be determined by the certiication body. NDT instruction writing examination element
8.2.4.1 The NDT instruction writing examination element shall involve the creation of a written NDT instruction by the Level 2 candidate. 8.2.4.2 8.2.5
See Table D.2 for D.2 for the weighting of the written examination instruction element. Grading of the Level 1 and Level 2 examination
8.2.5.1 The general, speciic, practical and NDT instruction writing examination elements shall be graded separately. When conventional pre-prepared paper-based examinations are used, an examiner shall be responsible for the grading of the examinations by comparison with model answers. E-assessment systems that automatically score candidate responses against stored data and grade the completed written examination according to prepared algorithms may be used. Each correct reply scores 1 point and the mark attributed to the tests is the sum of the points obtained. For the inal calculation, the mark of each test is expressed as a percentage. 8.2.5.2 The grading of the practical examination element shall be based on items 1 to 3 in Table 4, 4, with the recommended weighting factors in relation to the level and method as applicable.
© ISO 2021 – All rights r eserved
17
ISO 9712:2021(E)
Table 4 — Subjects and weighting factors for grading — Practical examination element Weighting factor I te m
Subjec t
1
Knowledge of NDT equipment and NDT media.
2
Application of NDT method
3
The detec tion of indic at ions or discontinuit ies and repor ting
Total
Level 1
Level 2
%
%
20
10
35
26
45
64
100
100
Table D.1 gives D.1 gives guidance on additional details on each item, to be taken into account, as applicable by the examiner.
8.2.5.3 For the Level 1 candidates to be eligible for certiication, they shall obtain a minimum grade of 70 % on each examination element (general, speciic and practical). For the practical examination element, a minimum grade of 70 % shall be obtained for each specimen tested. 8.2.5.4 The certiication body or authorized qualiication body may classify some discontinuities as mandatory to be detected. 8.2.5.5 For the Level 2 candidates to be eligible for certiication, they shall obtain a minimum grade of 70 % on each examination element (general, speciic, practical and NDT instruction writing). For the practical examination element, a minimum grade of 70 % shall be obtained for each specimen tested and NDT instruction writing element, as applicable. The certiication body or authorized qualiication body may classify some discontinuities as mandatory to be detected and evaluated as unacceptable. The NDT instruction writing element shall be graded in accordance with Annex D.
For AT, the required test instruction may relate to a specimen which is not tested during the practical examination element.
8.3 8.3.1
Examination content and grading for Level 3 General
All candidates for Level 3 certiication in any NDT method shall have successfully completed (with a grade of ≥ 70 %) the practical examination ex amination element for Level 2 in the relevant sector and method, except for the drafting draft ing of NDT instructions instruc tions for Level 1 (see (see 8.2.4.1 8.2.4.1). ). A candidate who is Level 2 in the same NDT method and product sector or who has successfully passed a Level 2 practical examination element for the NDT method in an industrial sector, as speciied in Annex A, A, is exempt from passing again the Level 2 practical examination element. This exemption is only valid for the product sectors covered by the industrial sector concerned and, in any other circumstances, the relevant sector is the sector in which the candidate seeks Level 3 certiication. 8.3.2
Basic examinatio examination n element
8.3.2.1 This written examination shall assess the candidate’s knowledge of the basic subjects using at least the number of multiple choice examination questions shown in Table 5. 5. Examination questions
18
© ISO 2021 2021 – All rights re served
ISO 9712:2021(E)
shall be selected in an unpredictable way from the certiication body’s or authorized qualiication body’s collection of basic examination element questions valid at the date of examination. Table 5 — Minimum required number of basic examination element questions for Level 3 Number of quesquestions
Item
Subjec t
A B
Technical knowledge in materials science and process technology. Knowledge Knowled ge of the certiication body’s qualiication and certiication certi ication system based on this document. This may be an open-book examination.
25 10
Ca
General knowledge of at least four methods as required for Level 2 and cho sen by the candidate from the methods given in Table 1. These four methods shall include at least one volumetric method (UT or RT).
15 for each test method (total 60)
a
For item C, the certiication certi ication body may adjust the number of questions per method for methods impacted by evolving technology, increasing methods and techniques being added.
8.3.2.2 It is recommended that the basic examination element be passed irst and remain valid, provided that the irst main method examination element is passed within ive years after passing the basic examination element. A candidate holding a valid Level 3 certiicate is exempt from the need to retake the basic examination element. 8.3.3
Main method examination element
This written examination shall assess the candidate’s knowledge of the main method subjects using the minimum required number of multiple choice questions shown in Table 6. 6. Examination questions shall be selected in an unpredictable way from the current collection of questions approved by the certiication body at the time of the examination. Table 6 — Minimum required number of main method examination element questions Item
Subjec t
Number of quesquestions
D
Level 3 knowledge relating to the NDT test method applied.
30
E
Application of the NDT method in the sector concerned, including the ap plicable codes, standards, speciications and procedures. This may be an open-book examination in relation to codes, standards, speciications and procedures.
20
Drafting of one or more NDT procedures in the relevant sector. The applica ble codes, standards, speciications and other procedures shall be available to the candida ca ndidate. te. F
For a candidate who has already drafted an NDT procedure in a successfully passed Level 3 examination, the certiication body may replace the drafting of a procedure with the critical analysis of an existing NDT procedure covering the relevant method and sector, and containing errors and/or omissions.
—
Applicable aids (8.1.4 (8.1.4)) shall be speci ied and communicated to candidates. These aids may be provided by the certiication body or authorized qualiication body for use in open-book examinations.
8.3.4 8.3.4.1
Grading of Level 3 examinations General
The grading of the basic ba sic and main method examination exam ination elements shall be done separately. To To be eligible for certiication, a candidate shall pass both the basic and main method examination elements. For the three items A, B, and C of the basic examination element and items D and E of the main method examination examinat ion element, element, the t he following requirements apply.
© ISO 2021 – All rights r eserved
19
ISO 9712:2021(E)
When conventional pre-prepared use d, an examiner shall be responsible res ponsible pre-prepared paper-based examinations are used, for the grading of the examinations by comparing the replies given by the candidate against answer keys approved by the certiication body. Each correct reply scores 1 point and the mark attributed to the tests is the sum of the points obtained. For the inal calculation, the mark of each test is expressed as a percentage. At the option of the certiication body, e-assessment systems that automatically score candidate responses against stored data and grade the completed written examination according to prepared algorithms may be used. 8.3.4.2
Basic examinat examination ion element
In order to pass the basic examination, the candidate shall obtain a minimum grade of 70 % in each of parts A, B, and C. 8.3.4.3
Main method examination element
In order to pass the main method examination, the candidate shall obtain a minimum grade of 70 % in each of parts D, E, and F. See Table D.3 for the recommended weighting of the written NDT procedure.
8.4
Conduct of examinations
8.4.1 All examinations shall be conducted in examination centres established, approved, and monitored by the certiication body, either directly or through an authorized qualiication body. 8.4.2 At the examination, the candidate shall have in their possession valid proof of identiication and an oficial notiication of the examination, which shall be shown to the examiner or invigilator upon demand. 8.4.3 Any candidate who, during the course of the examination, does not abide by the examination rules or who perpetrates, or is an accessory to, fraudulent conduct shall be excluded from all further examinations examinat ions for a period of at least one year. 8.4.4 Examination questions shall be validated by the certiication body. When conventional pre-prepared paper-based examinations are used, the examination papers shall be validated and
approved by an examiner, the grading done in accordance approved by the certiication body (see and 8.2.5 and 8.2.5 and 8.3.4). 8.3.4 ). shall Whenbee-assessment systemswith that procedures select questions, present the "written" examination to a candidate on a computer and grade the examinations are used, the certiication body shall validate and approve the e-assessment system. 8.4.5 Written (whether e-assessment or conventional) and practic practical al examinations examinat ions shall be invigilated invigilate d by an examiner or by one or more invigilators placed under a certiication body’s responsibility. 8.4.6 With the approval of the certiication body, a candidate for a practical examination may use their own equipment. 8.4.7 Candidates shall not be permitted to bring into the examination area personal items, unless speciically authorized to do so by the examiner.
8.5 Re-examination 8.5.1 A candidate failing for reasons of unethical behaviour shall wait at least 12 months before reapplying (see 8.4.3). 20
© ISO 2021 2021 – All rights re served
ISO 9712:2021(E)
8.5.2 A candidate who fails one or more elements of an examination (i.e. general, speciic, practical etc.) may retake the failed examination no more than twice:
a)
after a minimum minimum time of one one month month (which (which may may be reduc reduced ed if further training acceptable acceptable to the certiication body has been satisfactorily completed);
b)
no late laterr than two years years after the initial initial exami examinati nation. on.
8.5.3 A candidate failing two re-examinations on one or more elements shall complete further training, acceptable to the certiication body, and be required to retake all examination elements.
8.6
Supplementary examinations
8.6.1 A certiied Level 1 or Level 2 individual changing sectors or adding another sector for the same NDT method shall be required to take sector speciic and practical examination elements for the new sector. Level 2 shall also be required to write the NDT instruction for the new sector. 8.6.2 A certiied Level 3 individual changing sectors or adding another sector for the same NDT method shall be required to take the sector speciic items E and F of the main method examination element only (see Table 6).
9 Certiication 9.1 Administration A candidate fulilling all certiication requirements shall be certiied; and evidence of this certiication shall be made available by the certiication body. This can be achieved with the issue of hard copy certiicate(s), digital certiicates and/or by electronically uploading and displaying the relevant information on a database on the certiication body's website. The certiication body may also issue a wallet card that shall include a measure(s) to prevent falsiication.
9.2 Certiicates Certiicates shall include the following information as a minimum: a)
the name of the certiied individual, individual, and (option optional) al) date of birth birth of the certiied certiied individual; individual;
b)
a unique unique identiication identiication (e.g. (e.g. a photo, photo, or refere reference nce to a photo photo identiication identiication by number number); );
c)
the nam name e of of the the certii certiicati cation on bo body; dy;
d) the scope of of the certiication, including including referen reference ce to this document, document, the NDT method( method(ss) and level level of certiicat certi ication, ion, and/or and/or applicable techniques and sector(s), sector(s), including issue date; e)
any limita limitation tionss to the the certiicati certiication, on, if app applica licabl ble; e;
f)
the effe effective ctive date of certii certiicatio cation n and and date date of exp expiry; iry;
g) the signature and/ or authorizatio authorization n of a designated designated represe representative ntative of of the certi certiication ication body; h) contact informatio information n or websi website te address address to issuing certiication certiication body body database database for for veriication veriication purposes. Where the data listed above can be printed directly from the certiication body’s website, the printed output shall include a date of print and a statement that the current certiication status can be veriied at the relevant website.
© ISO 2021 – All rights r eserved
21
ISO 9712:2021(E)
9.3
Conditions of certiication
9.3.1
General
Certiication is granted, extended, suspended, withdrawn or revalidated by the certiication body. The maximum period of validity of the certiicate is 5 years. To be valid, certiicates shall be supported by a current annual veriication of acceptable vision as per 7.4. 9.3.2
Granting
Certiication shall be granted by the certiication body when all certiication requirements are fulilled. The period of validity shall commence upon the decision of certiication by the certiication body. 9.3.3
Scope extension
The certiicat certi ication ion body shall shall specify speci fy requirements for scope extension for situat situations ions where an individual seeks extension of their scope of of certiication certi ication for an existing certiicat cert iication ion (i.e. additional additional product sector). At the discretion of the certiication body: a)
the additional additional scope may be add added ed to the existing certi certiication ication and the original period period of validity validity maintained; or
b)
a new certiicate certiicate with a new period period of of validity may be be issued for the extensio extension n to scope scope only. only.
9.3.4
Suspension of certiication
Certiication may be suspended by the certiication body: a)
if the individual individual becom becomes es temporarily temporarily physically physically incapab incapable le of of performing performing their duties; duties;
b)
if the individual individual fails to provide provide evidence evidence of meeting meeting the visual acuity acuity requirements requirements of of this document annually;
c)
if a signiicant interruption interruption takes place place in the method method for for which which the individu individual al is certiied; certiied;
d) at the discretio discretion n of the certiicatio certiication n body body for any any other other situation situations. s. The certiication body shall specify the conditions for revalidation where an individual’s certiication has been suspended. 9.3.5
Withdrawal Withdra wal of certiication
Certiication shall be withdrawn by the t he certiication body: a)
at the discretion discretion of of the certiication certiication body, body, i.e. after reviewing reviewing evidence evidence of of behaviour behaviour incom incompatibl patible e with the certiication scheme or failure to abide by a code of ethics;
b)
if the individual individual fails to meet the requirem requirements ents of rene renewal, wal, until such such time as the individu individual al meets the requirements for renewal;
c)
if the individu individual al fails recertiication, recertiication, until until such such time as the individual individual meets the require requiremen ments ts for recertiication or certiication certi ication;;
d) at the discretion of of the certiication body, body, when veriiable veriiable eviden evidence ce is received received from the emplo employer yer stating that the individual has become physically incapable of performing their duties.
22
© ISO 2021 2021 – All rights re served
ISO 9712:2021(E)
9.3.6
Certiication after withdra withdrawal wal
The certiication body shall specify the conditions for certiication where an individual’s certiication has been withdrawn in the case of 9.3.5 a) and d). 9.3.7
Waiting period prior to certiication after withdra withdrawal wal
In case of 9.3.5 a), the certiication can only be granted after a minimum 12 month waiting period. The certiication body shall specify the length and conditions of the waiting period.
9.4
Certiicates issued by other certiication bodies
9.4.1 A certiication body may consider certiication issued by another certiication body. If so, the certiication body shall do so in accordance with a documented process. Where the certiication body takes into account work performed by another body, body, it shall have appropriate reports, report s, data and a nd records to demonstrate that the results are equivalent and conform to the requirements established by the certiication scheme. 9.4.2 This process shall consider the granting of credit for valid certiication including a review of education, training, experience, vision and examination requirements of the originating certiication body. The review may allow the certiication body to recognize the general theory part of a method examination. examinat ion. The review may also allow the certiicat certi ication ion body to recognize the speciic speci ic and/or and/or practical
examination elements but only when the method/technique, industry/product sector are appropriate. 9.4.3 Where the prior certiication is accepted without any additional examination, the expiry of the new certiication shall not extend beyond that of the prior certiication nor shall extend the scope of certiication.
10 Renewal 10.1 Prior to the completion of the period of validity following certiication and recertiication, certiication shall be renewed by the certiication body for a new period of validity on production of:
a)
documentary evidence documentary evidence of a satisfactory satisfactory near vision acuity examination examination taken within the precedin preceding g 12 months; and
b)
documentary evidence documentary evidence of a satisfactory colour colour vision vision and/ and/or grey scale scale perception perception examination taken within the preceding 60 months; and
c)
veriiable documen veriiable documentary tary evidence evidence of contin continued ued satisfactory work work activity without signiicant interruption in the method and sector for which certiicate renewal is sought; and either:
d) successful successful completio completion n of a practical practical examination ele elemen mentt in accord accordance ance with 11.2.2 except that it shall consist of a minimum of 50 % of the examination specimens required by 11.2.2; or e)
success suc cessfully fully meeting meeting the requir requirem ements ents of of the structured credit credit system system as given in 10.2 and Annex C .
If the criterion c) for renewal is not met, the individual shall complete the practical examination elements required by 11.2.2 11.2.2..
© ISO 2021 – All rights r eserved
23
ISO 9712:2021(E)
10.2 Where a candidate elects to use the structured credit system, they shall provide evidence to the certiicat certi ication ion body to demonstrate achievement of a minimum of 100 100 points in the t he 5 year renewal period based on the requirements of Table C.1. 10.2.1 For candidates seeking renewal of Level 1 certiicates, a minimum of 75 of the 100 points is required for any combination of activities listed in part A of Table C.1. 10.2.2 For candidates seeking renewal of Level 2 or 3 certiicates, certi icates, a minimum of 50 of the 100 points is required for any combination of activities listed in part A of Table C.1. 10.2.3 Where a certiication body has opted to implement a renewal period of less than 5 years, the minimum points required may be prorated accordingly [i.e. a 4 year renewal period would require a minimum of 80 points (100 × 4/5)]. 10.2.4 Where a candidate is seeking renewal for more more than one certiicate, certi icate, points granted gra nted for a speci speciic ic activity can be applied to the total points required for each certiicate for those activities not speciic to a particular method (e.g. “Current individual membership in NDT or NDT related society”). However, candidates shall meet the total number of points required (i.e. 100 points) for each certiicate for which renewal is being sought. 10.3 It is the responsibility of the certiicate holder to initiate the procedure required for renewal. 10.3.1 The renewal application should be made to the certiication body before the date of the expiration of the certiication and shall be no later than 12 months after the date of expiration of the certiicate. 10.3.2 If the renewal application is received prior to or on the date of expiration of the certiicate, the renewal date of the new certiicate shall be the same as the date of expiration of the certiicate (i.e. no interruption in certiication). The date of expiration of the new certiicate shall be no more than 5 years from the date of expiration of the original certiicate. 10.3.3 If the renewal application is received after the date of expiration of the certiicate, the renewal date of the new certiicate shall be the date on which all requirements for renewal are met. In this case, there shall have been an interruption in the certiication period. The date of expiration of the new certiicate shall be no more than 5 years from the date of expiration of the original certiicate. 10.4 The maximum period of validity of the certiicate at renewal is 5 years. 10.5 Certiicate holders at Level 1 and Level 2 not meeting the requirements for renewal shall fulil the requirements for recertiication as speciied in 11.2.2. Certiicate holders at Level 3 not meeting the requirements for renewal shall fulil the requirements for recertiication, as speciied in 11.3.1 11.3.1..
11 Recertiication 11.1 General Prior to the completion of each second period of validity, the certiied individual shall be recertiied by the certiication body for a new period of ive years or less, provided the individual meets the criterion for renewal speciied in 10.1 a) and 10.1 b) and meets the applicable conditions described in the following. It is the responsibility of certiicate holders to initiate the procedures required to obtain recertiication. If the recertiicat recert iication ion is applied applied for more more than 12 months after expir y of the period of validit validity, y, a complete
24
© ISO 2021 2021 – All rights re served
ISO 9712:2021(E)
examination (general, speciic, and practical) for Level 1 and Level 2 and a main method examination element ( Table 6, 6, items D, E and F) for Level 3 shall again be passed successfully.
11.2 Levels 1 and 2 11.2.1 Levels 1 and 2 certiicate holders seeking recertiication shall provide a conirmation issued by the employer of continued satisfactory work activity without signiicant interruption in the method 11.2.2.. and sector for which recertiication is sought and satisfy 11.2.2 11.2.2 The individual shall successfully complete the practical examination element which demonstrates continued competence to carry out work within the scope speciied on the certiicate. This shall include testing specimens (see Annex B) B) appropriate to the scope of recertiication and in addition, for Level 2, the production of a written instruction suitable for the use of Level 1 personnel (see 8.2.4.1 8.2.4.1). ). If the individual indiv idual fails to t o achieve a grade of at least 70 % for each specimen tested (weighted according to the guidance in Table 4), 4), and, for Level 2, for the instruction, two re-examinations of the recertiication examination shall be allowed after at least 7 days and within 12 months of the irst attempt at the recertiication examination. 11.2.3 In the event of failure in the two allowable re-examinations, the certiicate shall be withdrawn.
In order to reinstate certiication, a candidate shall: — complete furt further her trai training, ning, acceptable to the certi certiicat ication ion body; and — reta retake ke all examinat examination ion elemen elements ts required for initi initial al certi certiicat ication. ion. The date of expiration of the reinstated certiicate shall be no more than 5 years from the date of expiration expiratio n of the original certiicate. 11.2.4 If the criterion cr iterion in 11.2.1 for recertiication is not met, the individual shall complete the general, 11.1.. speciic and practical examinations required by 11.1
11.3 Level 3 11.3.1 Level 3 certiicate holders seeking recertiication shall provide a conirmation issued by the employer of continued satisfactory work activity without signiicant interruption in the method and sector for which recertiication is sought and:
a)
satisfy sa tisfy the the Leve Levell 3 requ require ireme ments nts of of 11.3.3 for a written examination; or
b)
meett the require mee requireme ments nts for for a structured structured credit credit system, system, as given given in 11.3.2 and Table C.1.
The individual shall decide between the examination or credit system for recertiication. If the credit system syst em is chosen and requires submission of employer’s employer’s documents or access to an emplo employer’s yer’s premises, the individual indiv idual shall provide to the certiicat cert iication ion body a written writt en statement of approval approval from the t he employer employer.. In both cases (written examination or credit system), the individual shall either provide appropriate documented evidence, acceptable to the certiication body, of their continued practical competence in the method or pass a Level 2 practical examination, as speciied in 11.2.2, except for the drafting drafti ng of NDT instructions.
© ISO 2021 – All rights r eserved
25
ISO 9712:2021(E)
11.3.2 Where a certiicate holder elects to use the structured credit system, they shall provide evidence to the certiicat cert iication ion body to demonstrat demonstrate e achievement of of a minimum of 100 100 points in the 5 year recertiication period based on the requirements of Table C.1.
For certiicate holders seeking recertiication of Level 3 certiication: — a minimum of 50 and a maximum of 70 of the 100 100 points is required for for any combination of of activities activit ies listed in item A of Table C.1; C.1; and — a minimum of 30 and a maximum of 50 of of the 100 100 points is required for any combination of of activities activit ies listed in item B of Table C.1. Where a certiication body has opted to implement a recertiication period of less than 5 years, the minimum points required may be prorated accordingly [(i.e. a 4 year renewal period would require a minimum of 80 points (100 × 4/5)]. 11.3.3 Where a certiicate holder elects to take the written examination or does not meet the structured credit system requirements, they shall successfully complete an examination that includes:
a)
a minimum of of 20 multiple multiple-choi -choice ce questions questions on the application application of of the test method in the sector(s sector(s) concerned which demonstrates an understanding of current NDT techniques, standards, codes or speciications, and applied technology; and
b)
a minimum of of 10 10 multiple-ch multiple-choice oice questions questions on on the requiremen requirements ts of the certiication body’s body’s certiication scheme.
11.3.4 If the individual fails to achieve a grade of at least 70 % in the recertiication examination, a maximum of two retests of the recertiication examination shall be allowed. The time period within which all tests are to be taken shall be 12 months, unless otherwise extended by the certiication body. 11.3.5 In the event of failure in the two allowable re-examinations, the certiicate shall be withdrawn.
In order to reinstate certiication, a candidate shall: — complete furt further her trai training, ning, acceptable to the certi certiicat ication ion body; and — reta retake ke all main method examinat examination ion items as required for for initi initial al cert certiicat iication. ion. The date of expiration of the reinstated certiicate shall be no more than 5 years from the date of expiration expiratio n of the original certiicate. 11.3.6 A candidate who applies for and does not meet the requirements of the credit system shall be recertiied in accordance with 11.3.3. In the event of failure at the irst attempt at recertiication by examination, only one retest of the recertiication examination shall be allowed within 12 months of the date of application application for recertiication via the structured str uctured credit system.
12 Files The certiication body shall be responsible for the maintenance of: a)
an actual list or or database of all certiied individuals individuals classiied accor according ding to leve level, l, NDT method and sector;
b)
an individual individual ile for for each candidate candidate who who has not not been been certiied, for for at least least ive years from from the date of application;
c)
an individual individual ile(s ile(s) for for each certiied individual individual and for each individual individual whose certiication has lapsed containing: 1)
26
a unique unique personal personal identiier identiier (e.g. a photo photo or referen reference ce to a photo identiication identiication by number number); );
© ISO 2021 2021
All rights re served
ISO 9712:2021(E)
2) ap appl plic icat atio ion n fo form rms; s; 3) examination record records, s, such such as questionnaires, questionnaires, answers, description description of specimens, specimens, records records,, results of test, NDT procedures, and grade sheets; 4) renewal renewal and recertiication recertiication documen documents, ts, including including evidence evidence of visual acuity acuity and continuo continuous us work wor k activity; activity ; 5) reaso reason( n(ss) for for any withdraw withdrawal al of certiica certiicatio tion. n. Individual iles shall be kept under suitable conditions of safety and conidentiality for as long as the certiicate remains valid and for at least one full certiication cycle after the certiication has lapsed. NOTE
The archiv archiving ing of specimen, data sets or radiographs is not required required..
13 Transition period 13.1 The aim of this clause is to permit the initiation of the system when a certiication body applies the certiication scheme to an NDT method, which is not yet covered within its scheme or when a new sector is created. The certiication body may temporarily appoint, for a period not exceeding ive years from the date dat e of implementat implementation ion of the new method or sector, duly qualiied personnel as examiners for the purpose of conducting, supervising and grading the examinations. The ive year implementation period is not to be used by the certiication body as a means to certify candidates who do not meet
all the qualiication and certiication requirements of this document. When new/additional training requirements of the new method or sector are adopted, currently certiied personnel shall provide documented evidence of full compliance at the next recertiication cycle. 13.2 Duly qualiied personnel means that such personnel:
a)
have the knowl knowledge edge of of the principle principless of NDT NDT and the speciic knowledg knowledge e in relation relation to the sector; sector;
b)
have industrial experien experience ce of of the app application lication of the NDT method method;;
c)
have ha ve the the abili ability ty to condu conduct ct examin examinati ation ons; s;
d) be able able to interpret interpret the questionn questionnaire aire and and results results of of examinations. examinations. 13.3 Within two years of the date of appointment, these examiners shall have gained certiication by 11.3.1.. satisfying the requirements requirements for recertiication as described in 11.3.1
27
© ISO 2021 All rights r eserved
ISO 9712:2021(E)
Annex A (normative) Sectors
A.1 General When creating a sector, the certiication body may standardize according to the reference lists of sectors in A.2 and A.3 . This does not preclude the development of additional sectors to satisfy national needs. Sector certiication may be available at all three levels of competence in all NDT methods or may be limited to particular methods or levels. However arranged, the scope of certiication shall be speciied on the certiicate.
A.2 Product sectors sectors These include:
— metallic materials: a)
castingss (c casting (c) (ferro (ferrous us and nonf nonferro errous us materials materials); );
b)
forgings (f) (all (all types of forgings: forgings: ferro ferrous us and non non-fe -ferrous rrous materials materials); );
c)
welds wel ds (w) (w) (all types of welds, welds, including including soldering, soldering, for for ferrous and and non-fe non-ferrous rrous materials); materials);
d) tubes and pipes pipes (t) (t) (seamless, (seamless, weld welded, ed, ferrous ferrous and non-fe non-ferrous rrous materials, includin including g lat products for the manufacturi manufac turing ng of welded pipes); pipes); e)
wrought prod products ucts (wp) (wp) exce except pt forgings forgings (i.e. (i.e. plates, plates, bar, bar, rods); rods);
— composite materials: f)
ceme ce ment nt ma matrix trix com compo posi sites tes (cc cc); );
g) reinfo reinforced rced plastics, such as ibre–reinfo ibre–reinforced rced polyme polymers rs (frp) (frp);; h)
metal me tal matrix matrix comp compos osite itess (mm (mmcc);
i)
ceram ce ramic ic ma matrix trix co comp mpos osite itess (cm (cmcc).
For composite materials, the certiication body shall specify the requirements for examination.
A.3 Industrial sectors Sectors combining a number of product sectors including all or some products or speciied materials (i.e. ferrous and non-ferrous metals or non-metals like ceramics, plastics, and composites): a)
manu ma nufa factu cturin ring g (m);
b) c)
pre- and in-se in-service rvice testing which inclu includes des manufa manufacturing cturing (s (s); railwa rail way y mai mainte ntenan nance ce (r);
d) ae aero rosp spac ace e (a).
28
© ISO 2021 2021
All rights re served
ISO 9712:2021(E)
When creating an industrial sector, the certiication body shall precisely specify in its published documentation the scope of the new sector concerned in terms of product, object or item. An individual certiied in an industrial sector shall be regarded also as holding certiication in each sector from which the industrial sector is composed.
29
© ISO 2021 – All rights r eserved
ISO 9712:2021(E)
Annex B (normative) Minimum number and type of specimens for the Lev Level el 1 and Lev Level el 2 practical examination element
a)
For all practical examination examination eleme elements, nts, candidates candidates shall be required to test one one or more more sector sector speciic specime specimen. n.
b)
If the candidate candidate is required required to test more more than one one specimen, specimen, each each specimen specimen shall be be different different in character, i.e. in product form, material speciication, shape, size, or discontinuity type.
c)
The evaluation evaluation and and interpretation interpretation of of a data set set shall be consid considered ered as equivale equivalent nt to testing one one specimen.
d) For a produ product ct sector related practical examination elem elements: ents: Candidates shall be required to test a minimum of two specimens and for multiple product sectors, a minimum of one from each product sector. sec tor. e)
Forr an industrial Fo industrial sector sector relate related d practical practical examinati examination on elem elemen ents: ts: Candidates shall be required to test at least two specimens, representative of products typically tested in the industrial sector.
f)
For RT ca can ndi dida date tess: Level 1 and Level 2 candidates shall radiograph at least two specimens. Level 2 candidates, already certiied as Level 1, shall radiograph at least one specimen. In addition to taking radiographs, Level 2 candidates shall interpret a set of at least 10 ilm images or 10 digital radiographic images. This set shall be considered as one specimen.
g) For LT can candi dida date tes: s: An examination involving both pressure change and tracer gas technique shall include at least one h)
specimen for each technique. When the certiication certiication sought sought is limited in appli application, cation, for for exampl example, e, thickness measure measuremen ment, t, radiographic interpretation or automated testing, the minimum number of specimens may be reduced by up to 50 % to one per sector. sec tor.
30
© ISO 2021 2021 – All rights re served
ISO 9712:2021(E)
Annex C (normative) Structured credit system for renewal Level 1, 2 and 3 and for Level 3 recertiication
C.1 General
31
© ISO 2021 – All rights r eserved
ISO 9712:2021(E)
a
n o i t a c i i t r e c e r 3 l e v e L r o f d n a 3
f y m r s u e t 5 o i t n b i r s v m r i m o e a i x u p v e t a n f o y c a M o f m o r e f y t p i 3 u r e s o l m r v e i b t a i n e t v x m L e M o c a n u i p y a r e p y s t t d i n e i v i t o t c P n a a r g
f y m r s u e t 5 o i t n b i r s v m r i m o e a i x u p v e t a n f o y c a M o f m o r e f y t p o i 2 u r e l m s r v e i b t a i t n v x m e c e a u i y a L M n o p
5 5 9 1
5 2
5 7
0 6
0 1
5 1
5
0 4
0 2
5 5 2
0 1
5 1
5 1
2
3
2
0 1
4
y a d / 1
a t n e s n o e r i t p / 1
r e e e t b p m i n e h e s m m / / 1 2
0 1
5 1
5
-
y a d / 1
y a d / 2
y a d / 1
k e e w / 1
5 5 9 1
5 2
5 7
0 6
y a d / 2
0 3
t i m e m o e c t / 1
5 1
. r a e 5 5 0 5 5 y 2 3 2 0 3 1 1 2 1 1 r a d n l a e r d n a r c t e a e i t e k e a y p n s y y y y y t b 2 e t m s t d i e a a a a a n , e p n e a s o m i e n e i v d d d d w d m 1 i e e e h o t t o / / / t / / / r i l t o t s m c n m n c p e P a a 2 1 2 1 1 1 / / d / v / r n 1 e 1 2 g 1 a L r l a f e a m r s t 5 o y y u e t w n i n b i r s v A 0 A A e 5 5 5 5 0 m o / / 5 / i m o e r i i 1 9 1 2 6 1 n t a t N N N v x p a e u c e o a n f y a c r i o M i r t o r f r f e o m e f y c u t r a m 1 e p o i A A A s e l m s 5 5 5 0 v / / / t 2 3 2 a t r b i i e a 1 2 1 s v x m t N N N d n e c i y e e a u o y a i s L i M n p t c i e d r p a r s e k e b s i s p y e t y y y y t n e r c t d i e a a a a e p s n A A A s m i i n v d d d d e / / / o d i t i e e w h h i / / / / t r t e N / N N o n t s , m r p P a c 2 1 2 1 e a l 1 / u / r b t 1 g a 1 c t u s . e i y n n i / r g a r i i r p h d r h t i t n n o l t s v e i t a o h y t e i i S p a n v e i - e i f a t e n h i n o s t n e h i i i c t n i i r o t c t e l r h n e i i t c i d — s a e t e a g i e c m a d n a m e l v r r l a h c t i b 1 h n h s t e n m a o ) i o t i . r t c l i e o c c e E s e m s d t i n n c i h n C r r e l a t T n r e t e / h d t s o h A e c e i f e e a a l t v d ” o x c h i e l D a l e e c f e y m d T t r t t e i f l a n o n n ) o a N t n b s d s t t u c r s l i o a ( c D o n o e q l h i a n e i n r r o e d a g n h c v a i n i h d a r a N h t e i i i t r u T A o n a l o c r r n t c f e d s o e o o e t n l e t h p a g d i s e d r e h e c t r o f i y d f d r i t i T e r i e e t n c i e m “ A v i e t n n e o e o o p s s c e e e i D v p t n i c n n h f i n i o ( o p o a s m a t a d N o n i u i z g h T e n o m o t o a n r r t T t p n t i o i e e i c n r l T a t q i a i i e c o / e a a D a r t e a D v d i t D t t y o r t t n n t h r p p c p t N e e p m l e t l e m r l d i N s i a d N l i n i h n T i a i h e o o c c c r n A r f B f n n a e t r c e e e i i h e i d o p n p v c h i i m o D r 2 e r f t r t r m r o m i g m h t i t t a t e r s g o t m e r t r s a e p r e u t r N c g o e a t a r n e i . a f e a a e o e e t h C n C n P n l n h n h i t i P e s m P p o C i P P C i D r m P i T i t P s o c W e e E S m 0 T 1 2 3 6 7 4 5 8 9 e 1 O t I N a
32
© ISO 2021 2021 – All rights re served
ISO 9712:2021(E)
f y m r s u e t 5 o i t n b i r s v m r i m o e a i x u p v e t a n f o y c a M o f m o r e f y t p o i 3 u r e l m s r v e i b t a i n e t v x m L e M o c a u p y a n i r e p y s t t d i n v i e i t o t n P a c r a g
f y m r s u e t 5 o i t n b i r s v m i i m o e r t x u p v a e a n f o y c a M o f m o r e y u t r p f o i 2 e l m s r v e i b t a i n v x m e t e a u i y c o L M n p a ) d e u n i t n o c (
1 . C e l b a T
0 4
0 1
y t i v i t c a / 2
0 3
. r a 0 e 1 y r a d n l a e r c y e t a i p y s t s v t d i i a t n v e i t i c t o n t a o n P a c / d a r 2 n g a r a s f e m r t y y u e n 5 o i t b i r s v A n m / o i i m o e r t t N i x u p v a a c e a n f o y a c i M o i t r f r e m o e f y c t p o i a 1 u r e A s l m s r v / a t b i i e t N d n a v x m e i c e e a o y a i L M u i n p c e r p s e s i s p y t t d i s A i n v e / i t i h t t N o c , P n e a a l r b g a t s . i y e l h t t i o r n i i v t T y d c a e D t d N o o s i l b n h t a s i f c n ” i y o ) o t s n i s l i h t v r i a ( a i c t c a t e e e c t i y d i A a t “ c i g r m e r i c n c e i t e a e p m h r i n t s r o o r 2 f f r h i t e . e P w h C W e e E S m 1 T e 1 O t I N a
© ISO 2021 – All rights r eserved
ISO 9712:2021(E)
C.2 Performanc Performance e of NDT activities C.2.1 In assessing this activity type, the certiication body should consider the responsibilities of employers as speciied in 5.5 and the duties speciied in Clause 6. 6. The following work activities may be considered as acceptable:
a)
knowledge knowl edge and unde understanding rstanding of of the custome customer’s r’s speciications and the inspection standards;
b)
veriication of operating operating condi conditions tions or setting up of the test equipme equipment, nt, successful successful performance performance of NDT, satisfactory reporting;
c)
perfo pe rforma rmanc nce e as a Lev Level el 3 exa examin miner er..
C.2.2 In order to assess the activities speciied in C.2.1, the certiication body may request from the individual seeking renewal or Level 3 recertiication documentation and/or evidence to demonstrate compliance including, but not limited to, the following:
a)
conirmation of the candidates candidates wor work k activities by a certi certiied ied individu individual al or refer referee; ee;
b)
conirmation of the level level of activity of the individu individual al in the given method method;;
c)
conirmation of formal formal documen documented ted competency competency or or proiciency proiciency test(s test(s) in the given given method; method;
d) date datess and and proto protocol col nu numbe mbers rs of of reports reports;; e)
detailss of detail of any any jo job b speciic speciic trainin training g rece received ived;;
f)
conirmati con irmation on of of empl employ oyer’ er’ss autho authorizatio rization n to oper operate; ate;
g) sum summary mary of acti activiti vities es and ou outpu tputs; ts; h)
job jo b/p /pos ositi ition on descr descrip iptio tion; n;
i)
annual/regular annual /regular emp employ loyer er assessme assessments nts of perfo performance rmance/ /comp competence etence;;
j)
sam sa mple ND NDT T re repo ports rts;;
k) sampl sample e procedu procedure( re(ss) devel developed oped (Level 3 only) only);; l)
cust cu sto omer fe feed edba back ck;;
m) conirmation of of adherence adherence to code code of ethics from from employ employer; er; n) conirmation of comp compliance liance with additio additional nal national national requireme requirements nts (i.e. radiation radiation safety). Other evidence may be deemed acceptable or be requested by the certiication body. The certiication body may require that some or all of the submitted evidence be conirmed by the employer.
33
34
© ISO 2021 2021 – All rights re served
ISO 9712:2021(E)
D Annex D (normative) Grading practical examination elements
D.1 Grading of Level 1 and Level Level 2 practical examination element —percentile weighting Table D.1 — Percentile weighting for practical examination element for Levels 1 and 2 Subjec t
% ma ximum (Level 1)
% maximum (Level 2)
10
5
10
5
20
10
5
2
Item 1 — Knowledge of the NDT equipment and/or NDT media:
a)
system and and/ /or med media ia knowl knowledge edge and con control trol;;
b)
validi vali dity ty of verii veriicati cation onss and/ and/or medi media. a.
Total Item 2 — Application of the NDT method: a) pre prepara paration tion of of the specime specimen n (i.e. surface surface condi condition tion), ), includ including ing visual examination;
b)
for Level Level 2, 2, the selection selection of the NDT NDT technique technique and and determina determination tion of of operating conditions;
c)
setting up of of the NDT app apparatus aratus and perf performa ormance nce of the the test; test;
d)
post test proce procedur dures es (i.e. demagn demagnetizati etization, on, cleaning, cleaning, preserva preservation tion). ).
Total
n/a
10
25
12
5
2
35
26
20
18
Item 3 — Detection of discontinuities and reporting:
a)
detection dete ction of mand mandato atory ry repo reportabl rtable e indi indicatio cations; ns;
b)
characterization characteriza tion of of indicatio indications ns (if appli applicabl cable e with respect respect to the test test method: type, position, orientation, apparent dimensions, etc.);
15
18
c)
Level 2 evaluatio Level evaluation n against against code, code, standard, standard, speciic speciicatio ation n or pro proced cedure ure criteria;
n/a
18
d)
produc t ion of t he tes t repor t .
10
10
45
64
100
100
Total Total items 1, 2 and 3
D.2 Grading of Level Level 2 writing examination examination elements Table D.2 — Percentile weighting for NDT instruction writing examination element for Level 2 NDT instruction writing (Level ( Level 2 candidates)
% maximum
5
a)
forewo for eword rd (sco scope, pe, refe referen rence ce do docume cuments nts))
b)
personnel
c)
equi eq uipm pmen ent/ t/m med edia ia to to be us used ed
d)
product produ ct (des (descrip cription tion or or drawing, drawing, includin including g area of interes interestt and purpose of the test)
e)
test con conditio ditions, ns, inc includ luding ing pre preparati paration on for testing
5
5
10 10
35
© ISO 2021 – All rights r eserved
ISO 9712:2021(E)
Table D.2 (continued) NDT instruction writing (Level 2 candidates)
% maximum
f)
detailed instructi detailed instructions ons for app applicati lication on of the test, inc includ luding ing settings
40
g)
recor rec ordin ding g and and class classifyin ifying g of the test test res results ults
20
h)
repor t ing t he result s
5
TOTAL
100
D.3 Weighting of Level Level 3 main method method examination examination element item F Table D.3 — Percentile weighting for the Level 3 NDT procedure examination Subjec t
% ma ximum
Item 1 — General:
a)
scope sco pe (ie (ield ld of ap appli plicatio cation, n, pro produ duct) ct);;
b)
doc ocum umen entt cont contro roll;
c)
normative references and complementar y infor mat ion.
2
2
4
Sub-tot al
8
Item 2 — NDT personnel
2
Item 3 — Materials and equipment:
a)
main NDT equip equipmen mentt (includ (including ing deining deining ve veriicati riication on status and pre-te pre-test st serviceabi serviceability lity checks);
10
b)
ancillary equipme equipment nt (re (referenc ference e and and calibration calibration bloc blocks, ks, consumables consumables,, measuring measuring equipment, viewing aids, etc.).
10
Sub-tot a l
20
Item 4 — Test piece:
a)
physical condition physical condition and surface preparation preparation (te (temperature, mperature, access, remo removal val of protective coatings, roughness, etc.);
b)
descripti des cription on of area area or volum volume e to be tested, inclu including ding refere reference nce datum; datum;
c)
discont inuit ies sought .
1 1 3
Sub-tot al
5
Item 5 — Performance of the test:
a)
NDT meth method( od(ss) and and techniq technique( ue(ss) to be used; used;
b)
settin se tting g up up the the ap appa para ratus tus;;
c)
condu con ducting cting the test test (incl (includin uding g referen reference ce to NDT NDT instruction instructionss);
d)
charac cha racter teriza izatio tion n of dis disco conti ntinu nuiti ities. es.
10
10
10
10
Sub-tot al
40
Item 6 — Accept ance c riteria
7
Item 7 — Post-test procedure:
a)
dispositi disp osition on of non non-con -conform forming ing produ product ct (labelling, (labelling, segregati segregation on); );
b)
restoratio resto ration n of of prote protective ctive coati coatings ngs (whe (where re require required). d).
2 1
Sub-tot al
3
Item 8 — Production of the test report
5
Item 9 — Overall present at ion Total
10 100
36
© ISO 2021 2021 – All rights re served
ISO 9712:2021(E)
Annex E (informative) Engineering of NDT
E.1 Deinition Engineering of NDT covers all the activities linked to NDT, from the design of the equipment to the responsibility responsibilit y of preparation, implementation implementation and veriication veriic ation of NDT (in manufacturing manufacturi ng and in service) of the same equipment belonging to industrial or technical installations.
E.2 Non-exhaustiv Non-exhaustive e list of activities cover covered ed The activities covered include: a)
at design design stage, deinition deinition of of requireme requirements nts to be taken into acco account unt and/ and/or veriication veriication of of inspectability during manufacturing and, where applicable, in service, of equipment;
b)
selection selectio n of NDT NDT techniques techniques to be be implem implemented ented in manufa manufacturing cturing and/or and/or in service; service;
c)
comparison com parison of speciic prescrip prescriptions tions of differen differentt codes codes and standards;
d) estab establishm lishmen entt or validati validation on of of the NDT proc procedu edures res;; e)
technical techn ical eval evaluati uation on of NDT sup suppli pliers ers;;
f)
evaluati eval uation on of of NDT techn techniq iques ues,, notabl notably y in the frame frame of expertis expertise; e;
g) treatm treatmen entt (technical (technical evalu evaluatio ation n) of non-c non-conf onformi ormity; ty; h) justiication to the custome customers rs and where where appli applicable, cable, to the associated associated safety authorities, authorities, of of practices practices implemented; i)
resp re spon onsi sibi bili lity ty for for an NDT NDT fac facil ility ity;;
j) co-o co-ordin rdinatio ation n and and supervisi supervision on of of NDT NDT perso personne nnell activities activities;; k) qua qualiica liication tion — validati validation on of NDT NDT techni techniqu ques: es: 1) establishme establishment nt of of input input information information’’s including including the inspection obj objectives; ectives; 2) deinition of the necessary mocks-u mocks-up p for for open open and, and, where where necessary necessary,, blind tests; 3) imp imple leme mentati ntation on of pra practical ctical tests; 4) prep preparation aration of technical justiication justiication includ including ing when when necessary necessary,, modelling; modelling; 5) pre prepara paration tion or or validatio validation n of NDT NDT proce procedur dures; es; 6) pre prepara paration tion or or validation validation of of qualiicati qualiication on dossi dossiers ers;; l)
establishment establishme nt of in-se in-service rvice inspection inspection programm programmes es for industrial installations or deinition of rules for the establishment of such programmes.
37
© ISO 2021 – All rights r eserved
ISO 9712:2021(E)
Annex F (informative) Training requirements for techniques
F.1 General This annex considers the increasing use of NDT techniques developed in the framework of an NDT method. This annex is also intended to provide guidance for an increasing request for competency in those techniques. The selection select ion of NDT techniques included in this thi s annex is not meant to be comprehensive nor exclusive and, therefore, leaves room for future techniques when their use becomes signiicant for inclusion in the annex. Direct access to Level 2 requires the total training days shown in each table for Levels 1 and 2. Direct access to Level 3 requires the total training days shown in the tables where applicable for Levels 1, 2, and 3. N/A means not applicable.
F.2
Recommended Recommend ed additi additional onal training days for techniq techniques ues
F.2.1
General
The training requirements for the techniques shown in Tables F.1 to F. F.4 4 are in addition to those for the method shown in Table 2. Note The trai training ning requirements for the base methods from Table 2 2 are reproduced in the irst line of Tables F.1 to F.3 F.3 for for convenience.
F.2.2 Validity Certiication in a technique is valid as long as the certiicate in the main method is valid. Table F.1 — Leak testing (LT) techniques additional training requirements Technique
Training requirements (days)
Abbreviated Abbreviate d term
LT (as per Table 2)
Level 1
Level 2
Level 3
5
9
6
LT pressure method
LT-P
3
4
LT tracer gas method
LT-TG
2
5
N/A N/ A N/A
Table F.2 — Magnetic testing (MT) techniques additional training requirements Technique Abbreviate Abbreviated d term
MT (as per Table 2) Flux leak age
MT-FL
Training requirements (days) Level 1
Level 2
Level 3
3
2
4
1
2
N/A
38
© ISO 2021 2021 – All rights re served
ISO 9712:2021(E)
Table F.3 — Ultrasonic testing (UT) techniques additional training requirements Technique
Training requirements (days)
Abbreviated Abbreviat ed term
Level 1
UT (as per Table 2)
Time of light
Level 3
10
5
5
5
N/A
5
5
N/A
8
UT-TOF D
Phased array
Level 2
U T- PA
Table F.4 — Ultrasonic testing (UT) techniques additional prerequisites Technique UT – TOFD
UT – PA
Level 1
Level 2
Level 3
UT 1
UT 2
N/A
UT 1
UT 2
N/A
NOTE The level state stated d in the table is the minimum acceptable level of cert certiic iic ation. A Level 3 certi icate holder satisies this requirement.
F.3 Recommen Recommended ded total training days days for radiographi radiographic c testing (RT) (RT) techniq techniques ues F.3.1
General
The training requirements for the techniques shown in Tables F.5 and F.5 and F.6 are the total training days required for certiication in the RT technique noted.
F.3.2 Validity Certiication in a technique is valid as long as the certiicate in the main method is valid, except for techniques with limited scope. Table F.5 — Radiographic testing (RT) techniques training requirements Technique
Technique with limited scope
Film & Digital
Level 1
RT - FD
8
RT – F
Fi l m
Digital Computed tomography
Radioscopy
RT Film interpreta tion RT digital image interpretation RT ilm and digital image interpretation NOTE
Training requirements (days)
Abbreviat ed Abbreviated term
Level 2
Level 3
10
8
5
10
5
RT- D
5
10
5
RT – CT
4
5
5
RT – S
4
4
RT – FI
N/A
8
RT – DI
NA
8
RT – FDI
NA
9
5
N/A N/ A
At the present time, trai training ning shown in Table 2 for 2 for RT is mainly ilm radiography (RT-F).
When the training syllabi are in agreement with the recommendations in ISO/TS 25107, several situations are to be considered, RT including then ilm and digital radiography (RT-FD).
F.3.3
Additional training requirements for ilm to digital transition transition
Candidates holding an RT-F certiicate and seeking certiication in RT-D need to have additional training, as shown in Table F.6.
39
© ISO 2021 – All rights r eserved
ISO 9712:2021(E)
Table F.6 t raining g requirements requirement s for RT-F to RT-D RT-D F.6 — Additional trainin Met hod
Technique
RT
Digital radiograp radiography hy
Abbreviat ed Abbreviated term
Level 1
Level 2
Level 3
3 da ys
5 days
3 days
RT-D
40
© ISO 2021 2021 – All rights re served
ISO 9712:2021(E)
Annex G (informative) Psychometric principles
If the certiication body choses to use psychometric principles for the written examinations, then the following shall be required. — Any reference to questions in this document document relates to scorable scorable questions, questions, however, however, all questions (scorable (sco rable and non-scorable non-scorable)) shall be considered when calculating calculati ng examination examinat ion times. — Scorable questions are approved approved and validated test items submitted to certiicat certi ication ion body body (or (or authorized qualiication body) for entry into the item bank. Non-scorable questions (not used to determine pass/fail) are items developed and approved for use on future examinations but are not statistically validated. Validation requires a minimum number of exposures and item analysis as speciied by the certiication body before use as a scorable question. — The minimum passing grade shall be 70 %. — The grading of examinat examinations ions shall shall be done in accordance with the psychometric process process speciied by the certiication body.
41
© ISO 2021 – All rights r eserved
ISO 9712:2021(E)
Bibliography [1]
ISO/TS 22809, Non-destructive testing — Discontinuities in specimens for use in qualiication examinations
[2] [3]
ISO/TS 25 25107, Non-destructive testing — NDT training syllabuses ISO/TS 25108, Non-destructive testing te sting — NDT personnel trainin t raining g organizations
[4]
CEN/TR 14748, Non-destructive testing — Methodology for qualiication of non-destructive tests
42
© ISO 2021 2021 – All rights re served
ISO 9712:2021(E)
ICS 03.100.30; 19.100 Price based on 42 pages
