ISO 286-2 Limits and Fits

February 14, 2017 | Author: Nitin P. Kumare | Category: N/A
Share Embed Donate


Short Description

Download ISO 286-2 Limits and Fits...

Description

STANDARD

First edition 1988-06-01

INTERNATIONAL ORGANIZATION FOR STANDARDIZATION ORGANISATION INTERNATIONALE DE NORMALISATION MEXAYHAPOAHAR

IS0 system

of limits

and fits

OPTAHM3A~Mfl

IlO CTAHJJAPTM3A~MM

-

Part 2: Tables of standard tolerance for holes and shafts

grades and limit deviations

Systkne

-

IS0 de tohances

Partie 2: Tables des degr& et des arbres

et d’ajustements de tolhance

normalis&

et des &carts limites des al&ages

Reference number IS0 286-2: 1988 (E)

COPYRIGHT 2003; International Organization for Standardization

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

INTERNATIONAL

IS0 286-2

Foreword IS0 (the International Organization for Standardization) is a worldwide federation of national standards bodies (IS0 member bodies). The work of preparing International Standards is normally carried out through IS0 technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. Draft International Standards adopted by the technical committees are circulated to the member bodies for approval before their acceptance as International Standards by the IS0 Council. They are approved in accordance with IS0 procedures requiring at least 75 % approval by the member bodies voting. This part of IS0 286 has been prepared by ISO/TC 3, Limits and fits, and, together with IS0 286-1, completes the revision of ISO/R 286, IS0 system of limits and fits. ISO/R 286 was first published in 1962 and subsequently confirmed in November 1964; it was based on ISA Bulletin 25 first published in 1940. The major changes

incorporated

in this part of IS0 286 are as follows:

a) The presentation of the information has been modified so that IS0 286 can be used directly in both the design office and the workshop. This has been achieved by separating the material dealing with the bases of the system, and the calculated values of standard tolerances and fundamental deviations, from the tables giving specific limits of the most commonly used tolerances and deviations. b) The new symbols js and JS replace the former symbols js and Js (i.e. s and S are no longer placed as subscripts) to facilitate the use of the symbols on equipment with limited character sets, e.g. computer graphics. The letters “s” and “S” stand for “symmetrical deviation”. c) Limit deviations have been included for basic sizes from 500 to 3 150 mm as standard requirements (these were previously included on an experimental basis only). d) Limit deviations have been extended for holes H and JS, for shafts h and js, by including tolerance grades IT17 and IT18 in all basic sizes, and, for experimental purposes only, by including tolerance grades IT1 to IT5 in basic sizes over 500 mm up to 3 150 mm. e) Limit deviations have been extended fo r some tole rance classes used in fine mechanisms and horology, in basic sizes UP to 50 mm.

f)

Inch values have been deleted.

9) The principles, terminology technology. bY contemporary

and symbols

have been aligned with

required

Users should note that all International Standards undergo revision from time to time and that any reference made herein to any other International Standard implies its latest edition, unless otherwise stated.

0

International

Organization

for Standardization,

1988

Printed in Switzerland

ii COPYRIGHT 2003; International Organization for Standardization

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

IS0 286-2 : 1988 (El

Contents

Page ........................................................

Introduction Scope

.............................................................

Field of application References

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

Standard

..................................................

......................................................... tolerances

.................................................

Limit deviations

for holes .............................................

Limit deviations

for shafts

Bibliography

........................................................

Notes on the presentation Tables2to32 Annex

............................................

of tables 2 to 32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

......................................................

8to38

- Graphical review of tolerance zones of holes and shafts . . . . . . . . . . . . . .

39

... III COPYRIGHT 2003; International Organization for Standardization

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

This page intentionally

left blank

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

COPYRIGHT 2003; International Organization for Standardization

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

IS0 system

IS0 286-2 : 1988 (E)

STANDARD

of limits

and fits

Part 2: Tables of standard tolerance for holes and shafts

0

grades and limit deviations

Introduction

The need for limits and fits for machined workpieces was brought about mainly by the inherent inaccuracy of manufacturing methods, coupled with the fact that “exactness” of size was found to be unnecessary for most workpieces. In order that function could be satisfied, it was found sufficient to manufacture a given workpiece so that its size lay within two permissible limits, i.e. a tolerance, this being the variation in size acceptable in manufacture. Similarly, where a specific fit condition is required between mating workpieces, it is necessary to ascribe an allowance, either positive or negative, to the basic size to achieve the required clearance or interference, i.e. a “deviation”. With developments in industry and international trade, it became necessary to develop formal systems of limits and fits, firstly at the industrial level, then at the national level and later at the international level. This International accepted system

Standard therefore of limits and fits.

gives the internationally

A general graphical representation of the relationship between the respective tolerance classes and their deviations is given in the annex.

1

-

Scope

This part of IS0 286 gives values of the limit deviations for commonly used tolerance classes (zones) for holes and shafts calculated from the information given in IS0 286-l. This part of

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

INTERNATIONAL

IS0 286 covers values for the upper deviations ES (for holes) and es (for shafts), and the lower deviations EI (for holes) and ei (for shafts) (see figure 1). NOTE - In the tables of limit deviations, the values for the upper deviation ES or es are shown above the values for the lower deviation EI or ei except for tolerance class JS and js which is symmetrical about the zero line.

2

Field of application

The IS0 system of limits and fits provides a system ances and deviations suitable for plain workpieces.

of toler-

It should be noted that the general term “hole” or “shaft” used in this International Standard can be taken as referring to the space contained by (or containing) the two parallel faces (or tangent planes) of any workpiece, such as the width of a slot or the thickness of a key (see also IS0 286-l 1. Similarly, the term “commonly used holes and shafts” shall be interpreted as providing a very wide choice of limit deviations suitable for a wide variety of requirements. For further information on terminology, system, etc., see IS0 286-l. Notes on the presentation page 7.

of tables

symbols,

bases of the

2 to 32 are given

on

1 COPYRIGHT 2003; International Organization for Standardization

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

IS0 286-2 : 1988 (E)

Zero line --`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

a)

Holes (internal features)

b)

Shafts (external features)

Figure 1 -

3

Upper and lower deviations

References

NOTE - See also clause 7. ISO 286- 1, /SO system of limits and fits tolerances, deviations and fits. IS0 1829, Selection

4

Standard

of tolerance

Part I : Bases of

zones for general purposes.

Attention is drawn to the fact that the tolerance classes shown in figures 2 and 3, and their limit deviations, given in tables 2 to 16, are not intended to give detailed directives on the selection of tolerance classes for any purpose. Recommendations for the selection of tolerance classes are given in IS0 1829. NOTE - Some tolerance classes are only provided for a restricted range of basic size steps. For further information, see note 1 on page 7.

tolerances 6

The values of standard are given in table 1.

tolerance

Limit

deviations

deviations

for shafts

A synoptic representation of the tolerance classes for shafts, given in this part of IS0 286, is shown in figures 4 and 5.

For information on the bases of the system and its application, see IS0 286-l ; for values of standard tolerances IT0 and ITOI, see IS0 286-1, annex A, table 5.

5

Limit

grades IT1 to IT18 inclusive

for holes

A synoptic representation of the tolerance classes for holes, given in this part of IS0 286, is shown in figures 2 and 3.

Attention is drawn to the fact that the tolerance classes shown in figures 4 and 5, and their limit deviations, given in tables 17 to 32, are not intended to give detailed directives on the selection of tolerance classes for any purpose. Recommendations for the selection of tolerance classes are given in IS0 1829. NOTE - Some tolerance classes are only provided for a restricted range of basic size steps. For further information, see note 1 on page 7.

2 COPYRIGHT 2003; International Organization for Standardization

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

Iso 286-2 : 1988 (El

7

IS0 2692, Technical drawings Maximum material principle.

Bibliography --`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

The following International Standards on tolerancing and tolerance systems will be useful with regard to the application of this part of IS0 286: IS0 406, Technical drawings ing - Indications on drawings.

Geometrical

IS0 2768-1, General tolerances tolerance indications - Part I: angular dimensions. 2,

Linear and angular toleranc-

IS0 1101, Technical drawings - Geometrical tolerancing Tolerancing of form, orientation, location and run-out Generalities, definitions, symbols, indications on drawings.

-

for dimensions without Tolerances for linear and

IS0 8015, Technical principle.

drawings

-

Fundamental

tolerancing

IS0 8062, Castings - System of dimensional tolerances.

1) At present under revision. At present at the stage of draft. (Revision, in part, of IS0 2768 : 1973.)

COPYRIGHT 2003; International Organization for Standardization

-

IS0 5166, System of cone fits for cones from C = 1 : 3 to 1 : 500, lengths from 6 to 630 mm and diameters up to 500 mm.

-

ISOIR 1930, IS0 system of limits and fits - Inspection ofplain workpieces. I)

2)

tolerancing

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

Is0

286-2 : 1988 (E)

Table 1 - Numerical

values of standard

tolerance

grades IT for basic sizes up to 3 150 mm ‘)

NOTE - This table, taken from IS0 286-1, has been included in this part of IS0 286 to facilitate understanding and use of the system. Standard

Basic size lT12)

mm Above

IT221 IT321 IT42)

IT521

up to and including

IT6

IT7

IT8

tolerance

Il.8

IT10

grades IT11

IT12

IT13

IT1431 IT1531 IT1631 IT173) lTW3)

Tolerances mm

33)

0,8

I,2

2

3

4

Pm 6

10

14

25

40

60

0,l

0,14

0,25

0,4

0,6

1

3

6

1

1,5

2,5

4

5

8

12

18

30

48

75

0,12

0,18

0,3

0,48

0,75

I,2

I,8

6

10

1

1,5

2,5

4

6

9

15

22

36

58

90

0,15

0,22

0,36

0,58

0,9

I,5

2,2

10

18

I,2

2

3

5

8

11

18

27

43

70

110

0,18

0,27

0,43

0,7

1,l

1,8

2,7

18

30

1,5

2,5

4

6

9

13

21

33

52

84

130

0,21

0,33

0,52

0,84

I,3

2,l

3,3

30

50

1,5

2,5

4

7

11

16

25

39

62

100

160

0,25

0,39

0,62

1

I,6

2,5

3,9

50

80

2

3

5

8

13

19

30

46

74

120

190

0,3

0,46

0,74

1,2

I,9

3

4,6

80

120

2,5

4

6

10

15

22

35

54

87

140

220

0,35

0,!54

0,87

1,4

2,2

3,5

5,4

120

180

3,5

5

8

12

18

25

40

63

100

160

250

0,4

0,63

1

I,6

2,5

4

6,3

180

250

4,5

7

10

14

20

29

46

72

115

185

290

0,46

0,72

I,15

I,85

2,9

4,6

72

6

8

12

16

23

32

52

81

130

210

320

0,52

0,81

1,3

2,l

3,2

5,2

8,1

-

114

250

315

315

400

7

9

13

18

25

36

57

89

140

230

360

0,57

0,89

1,4

2,3

3,6

5,7

83

400

500

8

10

15

20

27

40

63

97

155

250

400

0,63

0,97

I,55

2,5

4

6,3

9,7

500

6302)

9

11

16

22

32

44

70

110

175

280

440

0,7

I,1

I,75

2,8

4,4

7

11

630

8002)

10

13

18

25

36

50

80

125

200

320

500

0,8

I,25

2

3,2

5

8

12,5

800

10002)

11

15

21

28

40

56

90

140

230

360

560

0,9

1,4

2,3

3,6

5,6

9

14

1000

12502)

13

18

24

33

47

66

105

165

260

420

660

I,05

1,65

2,6

4,2

6,6

IO,5

16,5

1250

16002)

15

21

29

39

55

78

125

195

310

500

780

I,25

1,95

3,l

5

7,8

12,5

19,5

1600

20002)

18

25

35

46

65

92

150

230

370

600

920

1,5

2,3

3,7

6

9,2

15

23

2000

25002)

22

30

41

55

78

110

175

280

440

700

1100

1,75

2,8

4,4

7

11

17,5

28

2500

31502)

26

36

50

1 68

96

135

210

330

540

860

1350

2,l

3,3

5,4

8,6

13,5

21

33

1) Values for standard tolerance grades IT01 and IT0 for basic sizes less than or equal to 500 mm are given in IS0 286-1, annex A, table 5. 2)

Values for standard tolerance grades IT1 to IT5 (incl.) for basic sizes over 500 mm are included for experimental use.

3)

Standard tolerance grades IT14 to IT18 (incl.) shall not be used for basic sizes less than or equal to 1 mm.

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

COPYRIGHT 2003; International Organization for Standardization

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

IS0 286-2 : 1988 E)

B8 A9 B9 Al0 BIO All Bll Al2 812 Al3 B13

2

c8 C9 Cl0 Cl1 Cl2 Cl3

CD6 CD7 CD8 CD9 CD10

D6 D7 D8 D9 DIO Dll D12 D13

E5 E6 E7 E8 E9 El0

EF3 EF4 EF5 EF6 EF7 EF8 EF9 EFIO

3

F3 F4 F5 F6 F-7 F8 F9 FIO

FG3 FG4 FG5 FG6 FG7 FG8 FG9 FGIO

4

G3 G4 G5 G6 G7 G8 G9 GIO

5

HI H2 H3 H4 H5 H6 H7 H8 H9 HI0 HI1 HI2 HI3 HI4 HI5 HI6 HI7 HI8 6

JSI JS2 JS3 JS4 JS5 JS6 JS7 JS8 JS9 JSIO JSII JS12 JS13 JS14 JS15 JSl6 JS17 JSl8

7

K3 K4 K5 J6 K6 J7 K7 J8 K8 K9 KIO

M3 M4 M5 M6 M7 M8 M9 Ml0

N3 N4 N5 N6 N7 N8 N9 NIO Nll

9

8

P3 P4 P5 P6 P7 P8 P9 PI0

R3 R4 R5 R6 R7 R8 R9 RIO

s3 s4 s5 S6 s7 S8 s9 SIO

iii

ii

12

T5 T6 T7 T8

v5 x5 V6 X6 V7x7 V8 X8 x9 x10

U5 U6 u7 U8 u9 UIO

13

I

Y6 Y7 Y8 Y9 YIO

Z6 27 28 z9 ZIO Zll

14

ZA6 ZA7 ZA8 zA9 ZAIO ZAII

15

ZB7 ZB8 ZB9 ZBIO ZBII

16

Tables

Figure 2 - Synoptic

D6 07 D8 D9 DIO Dll D12 D13

representation

E6 E7 E8 E9 El0

of tolerance

F6 F7 F8 F9

3

4

G6 G7 G8

I

I

J

classes for holes for basic sizes less than or equal to 500 mm

H6 H7 H8 H9 HI0 HI1 HI2 HI3 HI4 HI5 HI6 HI7 HI8

JSI JS2 JS3 JS4 JS5 JS6 JS7 JS8 JS9 JSIO JSII JS12 JS13 JS14 JS15 JSl6 JS17 JSl8

6

7

K6 K7 K8

M6 N6 M7 N7 M8 N8 N9

P6 P7 P8 P9

R6 R7 R8

S6 s7 S8

T6 U6 T7 u7 T8 U8

9

10

11

12

13

L

5

8

Tables NOTE - The tolerance classes in the frame are given for experimental use.

Figure 3 - Synoptic representation of tolerance classes for holes for basic sizes greater than 500 mm and less than or equal to 3 150 mm

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

COPYRIGHT 2003; International Organization for Standardization

zc7 zc8 ZC9 ZCIO ZCII

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

IS0 286-2 : 1988 (El

c8 a9 a10 all al2 al3

b9 b10 bll b12 b13

c9 cl0 cl1 cl2

17

cd5 cd6 cd7 cd8 cd9 cdl0

f3 f4 f5 f6 f7 f8 f9 f10

ef3 ef4 e5 ef5 e6 ef6 e7 ef7 e8 ef8 e9 ef9 e10 efl0

d5 d6 d7 d8 d9 d10 dll d12 d13

18

19

fg3 fg4 fg5 fg6 fg7 fg8 fg9 fgl0

93 94 95 96 97 98 99 9’0

21

20

hl h2 h3 h4 h5 h6 h7 h8 h9 h10 hll h12 h13 h14 h15 h16 h17 h18 22

jsl 62 ja 64 j* js6 js7 ia id jsl0 jsl 1 js12 js13 js14 js15 js16 js17 js18 23

j5 j6 j7 j8

k3 k4 k5 k6 k7 k8 k9 k10 kll k12 k13

24

m3 m4 m5 m6 m7 m8 m9

p3 p4

n3 n4 n5 n6 n7 n8 n9

25

P5 P6 P7 p8 P9 P'O

r3 r4 r5 f-6 r7 r8 r9 r10

s3 s4 s5 s6 s7 s8 s9 SIO

26

27

28

t5 t6 t7 t8

u5 u6 u7 u8 u9

v5 x5 ~6x6 v7 x7 v8 x8

y6 y7 y8

By9 x10 y10

29

30

z6 z7 z8 z9 z10 zll

za6 za7 za8 za9 zal0 zall

31

zb7 zb8 zb9 zbl0 zbll

zc7 zc8 zc9 zcl0 zcll

32

Tables

Figure 4 - Synoptic

representation

of tolerance

classes for shafts for basic sizes less than or equal to 500 mm

jsl

d7 d8 d9 d10 dll --`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

18

e6 e7 e8 e9 e10

19

f6 f7 f8 f9

20

96 97 98

h6 h7 h8 h9 h10 hll h12 h13 h14 h15 h16 h17 h18

21

22

62 63 W js5 js6 js7 id id jsl0 jsll js12 js13 js14 js15 js16 js17 js18

23

k6 k7 k8 k9 k10 kll k12 k13

24

-

m6 n6 m7 n7

P6 P7 p8

f-6 r7 r8

s6 s7 s8

t6 u6 t7 u7 u8

25

26

27

28

29

Tables NOTE

-

The tolerance

classes in the frame are given for experimental use.

Figure 5 - Synoptic representation of tolerance classes for shafts for basic sizes greater than 500 mm and less than or equal to 3 150 mm

COPYRIGHT 2003; International Organization for Standardization

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

Is0 286-2 : 1988 (El

Notes

on the presentation

of tables

2 to 32

1 Values may be calculated, from the bases given in IS0 286-1, for fu ndamental deviations for which there is no entry in the tables, but for which the space has been left blank.

used for tolerance

classes,

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

2 A small horizontal separation has been inserted in the tables, where appropriate, to distinguis Ih between values for basic sizes less than or equal to 506 mm and those greater than 500 mm, which have been derived from different bases.

COPYRIGHT 2003; International Organization for Standardization

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

IS0 286-2 : 1988 (E)

Table 2 - Limit deviations

for holes A, B and Cl)

Upper limit deviation Lower limit deviation

= ES = EI Deviations in micrometres

~~ Basic size

AZ)

B2)

C

mm up to and ineluding

Above

9

IO

11

12

13

8

9

10

11

12

13

8

9

10

11

12

13

32)

+ +

295 270

+ +

310 270

+ +

330 270

+ +

370 270

+ +

410 270

+I54 +I40

+I65 +I40

+ +

180 + 140 +

200 + 140 +

240 + 140 +

280 140

+ 74 + 60

+ 85 +60

+I00 +60

+I20 +60+

+

160 + 60+

200 60

3

6

+ +

300 270

+ +

318 270

+ +

345 270

+ +

390 270

+ +

450 270

+I58 +I40

+I70 +I40

+ +

188 + 140 +

215 + 140 +

260 + 140 +

320 140

+ 88 + 70

+I00 + 70

+I18 + 70

+I45 + 70

+ +

190 + 70 +

250 70

6

10

+ +

316 280

+ +

338 280

+ +

370 280

+ +

430 280

+ +

500 280

+I72 +I50

+I86 +I50

+ +

208 + 150 +

240 + 150 +

300 + 150 +

370 150

+I02 + 80

+I16 +80

+I38 +80

+I70 +80

+ +

230 80

+ +

300 80

10

18

+ +

33 290

+ +

360 290

+ +

400 290

+ +

470 290

+ +

560 290

+-I77 +I50

+I93 +I50

+ +

220 + 150 +

260 + 150 +

330 + 150 +

420 150

+I22 + 95

+I38 + 95

+I65 + 95

+205 + 95

+ +

275 95

+ +

365 95

18

30

+ 352 + 384 + 430 +300+300+300+300+300

+

510

+

630

+I93 +I60

+212 +I60

+ +

244 + 160 +

290 + 160 +

370 + 160 +

490 160

+I43 +I10

+I62 +I10

+I94 +I10

+240 +I10

+ +

320 + 110 +

440 110

30

40

+ +

372 310

+ +

410 310

+ +

470 310

+ +

560 310

+ +

700 310

+209 +I70

+232 +I70

+ +

270 + 170 +

330 + 170 +

420 + 170 +

560 170

+I59 +I20

+I82 +I20

+220 +I20

+280 +I20

+ +

370 + 120 +

5'0 120

40

50

+ +

382 320

+ +

420 320

+ +

480 320

+ +

570 320

+ +

710 320

+219 +I80

+242 +I80

+ +

280 + 180 +

340 + 180 +

430 + 180 +

570 180

+I69 +I30

+I92 +I30

+230 +I30

+290 +I30

+ +

380 '30

+ +

520 '30

50

65

+ +

414 340

+ +

4.60 + 340 +

530 340

+ +

640 340

+ +

800 340

+236 +190

+264 +I90

+ +

310 + 190 +

380 + 190 +

490 + 190 +

650 190

+I86 +I40

+214 +I40

+260 +I40

+330 +I40

+ +

440 + 140 +

600 WJ

65

80

+ 434 + 480 + 550 + +360+360+360+360+360+200

660

+

820

+246

+274 +200

+ +

320 200

+ +

390 200

+ +

500 + 200 +

660 200

+I96 +I50

+224 +I50

+270 +I50

+340 +I50

+ +

60 + 150 +

6'0 '50

80

100

+ +

467 380

+ +

520 380

+ +

600 380

+ +

730 380

+ +

920 380

+274 +220

+307 +220

+ +

360 220

+ +

440 220

+ +

570 + 220 +

760 220

+224 +I70

+257 +I70

+310 +I70

+390 +I70

+ +

520 + 170 +

710 '70

100

120

+ +

497 410

+ +

550 4'0

+ +

630 410

+ +

760 410

+ +

950 410

+294 +240

+327 +240

+ +

380 240

+ +

460 240

+ +

590 240

+ +

780 240

+234 +I80

+267 +I80

+320 +I80

+400 +I80

+ +

530 + 180 +

720 180

120

140

+ +

560 460

+ +

620 + 4.60 +

710 460

+ +

860 460

+I090 + 460

+323 +260

+360 +260

+ +

420 260

+ +

510 260

+ +

660 260

+ +

890 260

+263 +200

+300 +200

+360 +200

+a +200

+ +

600 200

+ +

830 200

160

+ +

620 520

+ +

680 520

+ +

770 520

+ +

920 520

+1150 + 520

+343 +280

+380 +280

+ +

440 280

+ +

530 280

+ +

680 280

+ +

910 280

+273 +210

+310 +210

+370 +210

+460 +210

+ +

6'0 2'0

+ +

840 2'0

180

+ +

680 580

+ +

740 580

+ +

830 580

+ +

980 580

+I210 + 580

+373 +310

+410 +310

+ +

470 310

+ +

560 310

+ +

710 310

+ +

94-O +293 310 +230

+330 +230

+390 +230

+480 +230

+ +

630 230

+ +

860 230

200

+ +

775 660

+ +

845 660

+ +

950 660

+I120 + 660

+I380 + 660

+412 +340

+455 +340

+ +

525 340

+ +

630 340

+ +

800 340

+I060 + 340

+312

+240

+355 +240

+425 +240

+530 +240

+ +

700 240

+ +

960 240

225

+ +

855 740

+ +

925 740

+I030 + 740

+I200 + 740

+I460 + 740

+452 +380

+495 +380

+ +

565 380

+ +

670 380

+ +

840 380

+I100 + 380

+332 +260

+375 +260

+445 +260

+550 +260

+ +

720 260

+ +

980 260

225

250

+ +

935 820

+I005 + 820

+I 'IO + 820

+I280 + 820

+I540 + 820

+492 +420

+535 +420

+ +

605 420

+ +

710 420

+ +

880 420

+I140 + 420

+352 +280

+395 +280

+465 +280

+570 +280

+ +

740 280

+I000 + 280

250

280

+I050 + 920

+I130 + 920

+I240 + 920

+I440 + 920

+I730 + 920

+561 +480

+610 +480

+ +

690 480

+ +

800 480

+I000 + 480

+I290 + 480

+381 +300

+430 +300

+510 +300

+620 +300

+ +

820 300

+I110 + 300

280

315

+I 180 +I 260 +I()50 +I~~

+I 370 +I050

+I 570 +I050

+I 860 +I050

+62' +540

+670 +540

+ +

750 540

+ +

860 540

+I060 + 540

+I350 + 540

+411 +330

+460 +330

+540 +330

+650 +330

+ +

850 330

+'I40 + 330

315

355

+I340 +I200

+I430 +I200

+I560 +I200

+I770 +I200

+2000 +I200

+689 +600

+740 +600

+ +

830 600

+ +

960 600

+I170 + 600

+I490 + 600

+449 +360

+500 +360

+590 +360

+720 +360

+ +

930 360

+1250 + 360

355

400

+I490 +I350

+I580 +I350

+I710 +I350

+1920 +1350

+2240 +I350

+769 +680

+820 +680

+ +

910 680

+I040 + 680

+I250 + 680

+I570 + 680

+489 +400

+540 +400

+630 +400

+760 +400

+ +

970 400

+I290 + 400

400

450

+I655 +I500

+I750 +'gN,l

+I900 +I500

+2130 +I500

+2470 +1500

+857 +760

+915 +760

+lOlO + 760

+I 160 +I390 + 760 + 760

+I730 + 760

+537 +440

+595 +440

+690 +440

+840 +I070 +440+440+440

+I410

450

500

+I805 +I650

+I900 +I650

+2050 +I650

+2280 +I650

+2620 +I650

+937 +840

+995 +840

+I090 + 840

+1240 + 840

+I810 + 840

+577 +480

+635 +480

+730 +480

+880 +480

+I450 + 480

-

160 180 200

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

140

+I470 + 840

1) Fundamental deviations A, B and C are not provided for basic sizes greater than 500 mm.

2) Fundamental deviations A and B shall not be used for any standard tolerance in basic sizes less than or equal to 1 mm.

COPYRIGHT 2003; International Organization for Standardization

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

+I110 + 480

IS0 286-2 : 1988 (E)

Table 3 -

Limit deviations

for holes CD, D and E

Upper limit deviation Lower limit deviation

= ES = EI

Deviations in micrometres Basic size

CD’)

D

E

mm 1 Above 1~ZJ-

1 6 1 7 / 8 1 9 / IO 1 6

7

8

+ 30 + 20

+34 + 20

+ +

45+ 20 +

60+ 20 +

80 + 20 +

120 + 20 +

160 20

+ 18 + 14

+ 20 + 14

+ 42 + 30

4-48 + 30

+ +

60 + 30 +

78 + 30 +

105 + 30 +

150 + 30 +

210 30

+ 25 + 20

+ 28 + 20

cludlng 3

+40 +34

+# +34

3

6

+54 +46

+58 +46

6

10

+65 +56

-I-71 -1-78 +92 +56 +56 +56

+ 26 + 20

+I14 +56

15018011/ll 80

120

j

9

/

10

1 11

1 12

/

13

(

5

/

6

7

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

630

630

800

9

+ 55 +40

+ 61 +50

+68 +50

-l-77 +50

+ +

93 + 50 I+

120 + 50 +

160 + 50 +

230 + 50 +

320 50

+40 + 32

+43 + 32

+50 + 32

+ 78 + 65

+86 + 65

+98 + 65

+ +

117 ~+ 65 +

149 + 65 +

195 + 65 +

275 + 65 +

395 65

+49 +40

+53 +40

+ 61 +40

+ 73 +40

+ 92 +40

+ +

124 40

+96 +80

+I05 +80

+I19 + 80

+ +

142 + 80 +

180 + 80 +

240 + 80 +

330 + 80 +

470 80

+ 61 +50

+66 +50

+ 75 +50

+89 +50

+I12 +50

+ +

150 50

I I I I I I I I I /I +'I9 +I00

+130 +I00

+146 +I00

+I42 +I20

+I55 +I20

+I74 +I20

+ +

174 + 100 +

220 + 100 +

290 + 100 +

400 + 100 +

560 100

+ 73 + 60

+ 79 + 60

+ 90 + 60

+I90

+242 +I90

+246 +210

+267 +210

+270 +230

+ 293 +230

+271 +I90

+ +

320 + 190 +

400 + 190 +

510 + 190 +

710 +I000 190 + 190

+I33 +I10

+I06 + 60

+I34 + 60

+I07 + 72

+I25 + 72

+I25 +85 +I46 +I00

610 + 290 I +

+ +

180 60

+I59 + 72

+ +

212 72

+I48 +85

+I85 +85

+ +

245 85

i-172 +I00

+215 +I00

+285 + 100

+-l-i +214 +I25

+265 +I25

+ +

355 125

+232 +I35

+290 +I35

+ +

385 135

790 290 I

+376 +320

+410 +320

+460 +320

+ +

550 + 320 +

+416 +350

+455 +350

+515 +350

+ +

610 + 770 +I010 350 +350 +350

/ / / 1

+590 +480

+655 +4ao

+760 +480

+655 +520

+730 +520

+850 +520

I I

+I42 +I10 +I82 +I25

+ +

/I

680 +880 320 + 320

+I 720 + 320

+226 +I70 +261 +I95 +530 +220

b&d

10

+49 +40

I 250/ 3151 I I I I I+2221 I I I I I I I I 500

8

I I + +

720 220

1) The intermediate fundamental deviation CD is provided primarily for fine mechanisms and horology. If tolerance classes involving this fundamental deviation in other basic sizes are required, they may be calculated in accordance with IS0 286-l.

COPYRIGHT 2003; International Organization for Standardization

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

Iso

286-2 : 1988 (El

Table 4 -

Limit deviations

for holes EF and F

Upper limit deviation Lower limit deviation

= ES = EI Deviations in micrometres

EF’) I

up to and inr+IInrlinrr bIUUII iy

Above

3

4

5

6

7

8

9

10

3

+I2 +I0

+I3 +I0

+I4 +I0

+I6 +I0

+20 +I0

+24 +I0

+35 +I0

+50 +I0

3

6

+16,5 +I4

+I8 +I4

+I9 +I4

+22 +I4

+26 +I4

+32 +I4

+44 +I4

6

IO

+20,5 +I8

+22 +I8

+24 +I8

+27 +I8

+33 +I8

+40 +I8

+54 +I8

10

3

I

I

4

5

6

7

8

+8 +6

+9 +6

+I0 +6

+ 12 +6

+ 16 +6

+62 +I4

+12,5 +I0

+I4 +I0

+I5 +I0

+I8 + 10

+76 +I8

+15,5 +I3

+I7 +I3

+I9 +I3

18

+I9 +I6

+21 +I6

18

30

+24 +20

30

50

+29 +25

50

I

9

10

+ 20 +6

+31 +6

+46 +6

+22 + 10

+28 + 10

+40 + 10

+58 + 10

+22 + 13

+ 28 + 13

+35 + 13

+49 + 13

+ 71 + 13

+24 +I6

+27 + 16

+34 + 16

+43 + 16

+59 + 16

+ 86 + 16

+26 +20

+29 +20

+33 + 20

+41 + 20

+53 + 20

+ 72 + 20

+I04 + 20

+32 +25

+36 +25

+41 + 25

+50 + 25

+64 + 25

+ 87 + 25

+I25 + 25

80

+43 +30

+49 + 30

+60 + 30

+ 76 + 30

+I04 + 30

80

120

+51 +36

+58 + 36

+71 + 36

+90 + 36

+I23 + 36

120

180

+61 +43

+ 68 +43

+83 +43

+I06 +43

+I43 4-43

180

250

+70 +50

+79 +50

+96 +50

+I22 +50

+I65 +50

250

315

+79 +56

+88 +56

+I08 +56

+I37 +56

+I86 +56

~-87 +62

+ 98 + 62

+I19 + 62

+I51 + 62

+202 + 62

+I31 +c

+I65 +68

+223 +68

-

315

400

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

400 .

500 .

+95 I

.

I

. +68

+I08 I +%

500

630

+I20 + 76

+I46 + 76

+I86 + 76

+251 + 76

630

800

+I30 +80

+I60 + 80

+205 + 80

+280 + 80

800

1 000

+I42 +86

+I76 +86

+226 +86

+316 +86

1000

1 250

+I64 + 98

+203 + 98

+263 +98

+358 +98

1 250

1 600

+I88 +I10

+235 +I10

+305 +I10

+420 +I10

1 600

2 000

+212 +I20

+270 +I20

+350 +I20

+ 490 +I20

2 000

2 500

+240 +I30

+305 +I30

+410 +I30

+570 +I30

2500

3 150

+280 +I45

+355 +I45

+475 +I45

+685 +I45

I



F

I

1) The intermediate fundamental deviation EF is provided primarily for fine mechanisms and horology. If tolerance classes involving this fundamental deviation in other basic sizes are required, they may be calculated in accordance with IS0 286-l.

10 COPYRIGHT 2003; International Organization for Standardization

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

ISO286-2:1988

Table 5 -

Limit deviations

EI

for holes FG and G

Upper limit deviation Lower limit deviation

= ES = EI Deviations in micrometres

Basic size

FG’)

G

mm Above -

3 6

up to and includina

3

4

5

6

7

8

9

10

3

4

5

6

7

8

9

10

3

+6 +4

+7 +4

+8 +4

+I0 +4

+I4 +4

+I8 +4

+29 +4

+44 +4

+ 4 +2

+5 +2

+6 +2

+8 +2

+ 12 +2

+ 16 +2

+ 27 +2

+ 42 +2

6

+ 8,5 +6

+I0 +6

+I1 +6

+I4 +6

+I8 +6

+24 +6

+36 +6

+54 +6

+ 6,5 +4

+ 8 +4

+ 9 +4

+ 12 +4

+I6 +4

+22 +4

+34 +4

+ 52 +4

+10,5 +8

+I2 +8

+I4 +8

+I7 +8

+23 +8

+30 +8

+44 +8

+66 +8

+ 7,5 +5

+ 9 +5

+I1 +5

+ 14 +5

+ 20 +5

+ 27 +5

+41 +5

+63 +5

I0

10

18

+9 +6

+I1 +6

+I4 +6

+ 17 +6

+24 +6

+33 +6

+49 +6

+ 76 +6

18

30

+I1 +7

+I3 +7

+I6 +7

+ 20 +7

+28 +7

+40 +7

+59 i-7

+ 91 +7

30

50

+I3 +9

+I6 +9

+20 +9

+25 +9

+34 +9

+48 +9

+ 71 +9

+I09 +9

50

80

+23 +I0

+29 + 10

+40 + 10

+56 + 10

80

120

+27 +I2

+34 + 12

+47 + 12

+66 + 12

120

180

+32 +I4

+39 + 14

+54 + 14

+77 + 14

180

250

+35 +I5

+44 + 15

+ 61 + 15

+ 87 + 15

250

315

+40 +I7

+49 + 17

+69 + 17

+98 + 17

315

400

400

500

500

630

630

800

800

1 000

+43

+54

+I8

+ 18

+ 75 + 18

+I07 + 18

-I47 +20

+60 + 20

+83 + 20

+I17 + 20

+66 +22

+ 92 +22

+I32 +22

+ 74 + 24

+I04 + 24

+I49 + 24

+82

+I16 + 26

+I66 + 26

+ 28

+I33 +28

+I93 +28

+ 26 1 000

1 250

+94

1 250

1 600

+I08 +30

+I55 + 30

+225 + 30

1600

2 000

+I24 +32

+I82 +32

+262 +32

2000

2500

+I44 +34

+209 +34

+314 +34

2500

3 150

+I73 +38

+248 +38

+368 +38

1) The intermediate fundamental deviation FG is provided primarily for fine mechanisms and horology. If tolerance classes involving this fundamental deviation in other basic sizes are required, they may be calculated in accordance with IS0 286-l.

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

COPYRIGHT 2003; International Organization for Standardization

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

~so 286-2 : 1988 (El

Table 6 -

Limit deviations

for holes H

Upper limit deviation Lower limit deviation

I

Basic size

H

I

mm

I

Above

1

2

3

4

5

6

up to and in1 eluding 1

-

3

+ 3 0

+ 4 0

+

6 0

+ 10 0

+I4 0

0

0

6

+I

+1,5+2,5

+4

+5

+

8

+ 12

0

0

+ 18 0

+ 30 0

+22

+36

0 +15+25+4

10

I8

+I,2 0

+ 2 0

o’

0

0

0

o’

o

+ 3 0

+1,5+2,5+4

5o

+I,5

+2,5+4

0 80

+;

+;

o

+ 8 0

+6

+9

0 +;

+6

+ 5 0

-1-7

0

0

+'i

0 +;

+'3 0

180

12o

o +2,5

180

+3,5+5

250

+ 4o

0

0

+4,5

-I- o+l; 7

+

+ 11 0

+I5

+25

12 I I

+ 0,9 0

+ I,5 0

+ 2,2 0 + 2,7 0

+ 52

+ 84

+

0

0

130 0

+0,21 0

+0,33 0

+0,52 0

+0,84 0

+ I,3 0

+ 2,' 0

+ 3,3 0

+

160 0

+0,25 0

+0,39 0

+0,62 0

+I 0

+ I,6 0

+ 2,5 0

+ 3,9 0

190 0

+0,3 0

+0,46 0

+0,74 0

+I,2 0

+I,9 0

+3

+ 4,6 0

+

22;

+;.,,

+;,54

+;,87

+;,4

+ 2,2 0

+ 3,5 0

+ 5,4 0

+

250 0

+0,4 0

+0,63 0

+I 0

+I,6 0

+ 2,5 0

+ 4 0

+ 6,3 0

-t

290 0

+0,46 0

+0,72 0

+I,15 0

+I,85 0

+ 2,9 0

+ 4,6 0

+ 7,2 0

+I20

+ 3;

+ ";:

+ 87 0

+I;

+40

+63

+I00

+I60

+39

0

0 + 72

+52

0I

+81

0I

+I15

+ 0

0 +I85

0

o

o +210 0

+

0

320 0

+0,52 0

+0,81 0

+I,3 0

+2,1 0

+ 3,2 0

+ 5,2 0

+ 8,l 0

+230 0

+

0

360 0

+0,57 0

+ 0,89 0

+I,4 0

+2,3 0

+ 3,6 0

+ 5,7 0

+ 8,9 0

+250

+

400

+0,63

-t 4

+ 6,3

+ 9,7

01

01

+I30

0I

0

0

+I55

800

+0,58 0

+ I,8 0

+ 97

+I0

+0,36 0

+ 74 0

0 I

0I

0I

01

0

+0,97

I

0

+I,55

I

0

+2,5

lo

Iol

+ 4:

+ 7;

+I10 o

+I75 o

+280o

+

440 0

+0,7 0

+ I,' 0

+I,75 0

+2,8 0

+ 4,4 0

-I- 7 0

+I1

+ ;

+ 80

o

+I25

+200

+320

+

500 0

+0,8 0

+I,25 0

+2 0

+3,2 0

+5

+8

+12,5 0

+ 90

+I40

+230

+360

+

560 0

+0,9 0

+I,4 0

+2,3 0

+3,6 0

+ 5,6 0

+ 9 0

+I4

+I05

+I65

+260 0

+420 0

+

660 0

+I,05 0

+I,65 0

+2,6 0

+4,2 0

+ 6,6 0

+10,5 0

+16,5 0

250 1 11600 600 iI+li +I5 / +21 1 11250 +2! / +29 +2: 1 +39 +si / +55 +5i /I + 78 7; / +I25 11 +I95 1 / +31011 +50011 + 78011 +I,25 1

/ +I,95 1

/ +3,1 +itl

500 630

o

+I;

+I;

+3;

+0,22 0

+ I,' 0

+ 63

+$

+0,15 0

+0,7 0

+ 40

+I;

90 0

+0,43 0

+I40

+I:,

+

+0,27 0

+ 89 0

+ ;

+58

+0,18 0

+ 57 0

630

+ I,8 0

110 0

+ 36 0 +27

+ I,2 0

+

0

0I

+ 0,75 0

+ 70 0

315 +20

+0,48 0

+ 43 0

0

0 I

+0,3 0

+ 27 0

+I4 o+2;+2;+;

+I5

+0,18 0

+ 18 0

0

0 I

+0,12 0

0

0

+I0

75 0

0

+32

+8

+

0

o

5oo I 0 I

+ 48 0

+ 46 0

+25

I + 0,6 0

+ 30 0

+I:

mm +0,4 0

+ 19 0

0

18’)

+0,25 0

+I00

+I2

17’)

+0,14 0

+ 62 0

+8

16’)

+O,l 0

0

+ $

15’)

60 0

0

+I;

14’)

+

+25

o + 10

13

0

250

400 ,

+40

+ 16 0

+ o6

0

9 0

o

I

11

+ I,2 + 2 0 0

18

I

10

+0,8 0

+’

120

9

31,

10

80

8

Deviations

6

50

7

Pm

0

30

= ES = EI

'f

+3;

800 1 000

1250

+I3

+I8 0

0

0

1 600

2ooo

+I8 o

+24 0

0 +2;

+33 0

0 +3;

A-47 0

0 +;

0 +6;

+66 0

0

0 + 92 0

3150 3150

+26

+36

0

0

+50

0

+68 +96 010 0 0

+13E +I35 0

0

o

o

0

0

0

0

+370 0

+600 0

+

0

+230 0 +280

+440

+700

+I100

+I50

2 000 22 500 500

o

+210 0

+330 0

+540 0

+86O 0

1 +5 +i

0

0

0

0

19,5 1 + 7,8 %t8 1 +12,5 +I:15 1 ++'%.s)

0

0

0

0

920 0

+I,5 0

+2,3 0

+3,7 0

+6 0

+ 9,2 0

+I5

0

+I,75 0

+2,8 0

+4,4 0

+7 0

+I1 0

+17,5 0

+28 0

0

+2,1 0

+3,3 0

+5,4 0

+8,6 0

+13,5 0

+21 0

+33 0

+I350

0

0

0

0

0

+23 0

1) Tolerance grades IT14 to IT18 (incl.) shall not be used for basic sizes less than or equal to 1 mm. 2) The values given in the frame, for tolerance grades IT1 to IT5 (incl.), for basic sizes greater than 500 mm and less than or equal to 3 150 mm, are included for experimental use.

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

COPYRIGHT 2003; International Organization for Standardization

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

*

f0,75

18

30

50

10

18

30

5,5

1 + 9

I!I 7,5

+6,5

f

+5

+4,5

f4

f3,5

f2,5

+2

*1,5

&I,25

&I,25

fl

f0,75

f0,75

+0,6

2

3,5 6,5

3)

8

+33

+67,5

+55

+46

11 3139

(I

k28

11 +25

f22

+20

+I8

+I6

+14,5

fl2,5

fll

k 9,5

f

9

12,5

20

17,5

28,5

9

13,5

11

19,5

27

36

44,5

f

1 f

k 15

37

31

65

77,5

31 87,5

f

IL 70

f

+ 57,5

250

AI 43,5

f

f

k 26

I?I 21,5

I!I 18

70

fl15

62.5 I 1 +I00

f. 55

Ik 48,5

f

ZiI 40,5

f

+31,5

f

+ 23

f

AZ 16,5

f

f

k

z!I 7

AI 12,5

75

&IO5

+I85

+270

k220

Z!I 24

42

f430

+350

+300

j _+250

1 k210

+I80

1 +I60

fl40

f125

&I15

f105

Ik 92,5

280

z!I 70

Ik60

IL50

f

+ 35

+29

95

65

+675

+550

+460

1 k390

1 k330

+280

+220 I 1 +250

+200

AI180

f.160

+145

+I25

+110

f

f80

f

I!I 55

k45

IL 37,5

+30

11

&I,05

f0,875

+0,75

1 f0,625

1 +0,525

*0,45

1 zkO.4

f0,35

f0,315

kO,285

+0,26

+0,23

+0,2

+0,175

+0,15

20,125

Iko,105

AI0,09

f0,075

f0,06

+0,05

12

*I,65

+1,4

&I,15

1 f0,975

1 kO,825

+0,7

1 +0,625

f0,55

f 0,485

f0,445

Ik 0,405

kO,36

f0,315

+0,27

+0,23

z!I0,195

+0,165

+0,135

kO,ll

zk0,09

f0,07

13

+2,7

+2,2

&I,85

1 fl,55

( +I,3

&I,15

1 +I

+0,875

f0,775

f0,7

+0,65

f0,575

f0,5

f0,435

+0,37

f0,31

f0,26

f0,215

+0,18

f0,15

+0,125

142)

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

this is to be interpreted as ES = +x and EI = -x, e.g. T i;$i pm.

+I65

L-140

It115

62,5 1 IL 97,5 1 &I55

31 87,5

f

1 f

10

f. 20

Deviations

9

( k 52,5 1 f. 82,5 1 +I30

AI 45

1 It 40

zk 35

AI 31,5

f

3~ 26

k 23

f

f

It 15

f

z!I IO,5

f

7,5

6

5

8

+4,3

f3,5

f3

1 f2,5

1 f2,l

+I,8

1 &I,6

&I,4

+I,25

&I,15

+1,05

* 0,925

f0,8

+0,7

f0,6

f0,5

+0,42

f0,35

+ 0,29

f0,24

f0,2

mm

152)

f6,75

+5,5

f4,6

1 +3,9

1 +3,3

+2,8

1 +2,5

f2,2

+2

+I,8

&I,6

&I,45

&I,25

+ I,1

f 0,95

f0,8

+0,65

f0,55

f0,45

-fo,375

+0,3

162)

The values in the frame, for tolerance grades IT1 to IT5 (in&), for basic sizes greater than 500 mm and less than or equal to 3 150 mm, are included for experimental use.

+48

3139

+32,5

1 f27,5

1 +23,5

+20

fl6 I 1 fl8

fl3,5

+12,5

&II,5

f 10

k9

I!I 7,5

f

rt 5,5

5,5

I!I 6,5

f

IL

k

I!I

7

3)

+34

+27,5

+23

1 +19,5

1 &16,5

fl4

1 kl2.5I

&II

f 10

+9

f8

f7

f6

f5

+4

f

4

+ 4,5

f

AI 4,5

31 4

+3

Pm

6

Tolerance grades IT14 to IT16 (incl.) shall not be used for basic sizes less than or equal to 1 mm.

L-25

2,5

_+3

f

+3

31 2,5

+2

5

2)

+I8

fl7,5

+20,5

2

Z!I 2

f

&I,5

4

JS

= ES = EI

for holes JS

In order to avoid repetition of equal values, the table lists the values as ” f x”;

&I3

3 150

2500

+12,5

rtl5

1 +14,5

1 +I2

&IO,5

zk 9

I!I 8

+7,5

+6,5

+6

+5

f4

+3

f2,5

f2

+2

+1,5

&I,25

&I,25

fl

3

Limit deviations’)

Upper limit deviation Lower limit deviation

Table 7 -

1)

&II

f 9

11 z!I 7,5 ( HO,5

2 000

1 1600

1 1250

11 I!I 6,5

2500

1 1250

1 1000

AI 5,5

1600

1 000

800

AI 5

Ik 4,5

+3

2ooo

630

800

500

400

630

+4

400

315

500

+3,5

315

250

+2,25

&I,75

180

250

+I,25

180

+I

80

120

50

80

_+0,75

+0,6

*0,5

&0,5

6

10

6

+0,4

3

32)

1

120

-

Above

Upto . and in&ding

mm

Basic size

COPYRIGHT 2003; International Organization for Standardization

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

I,25

2,3

2

I,75

3,15

0,9

2,7

2,3

I,95

5,5

4,85

+7

1 21 6,25 1

f

f

AI 4,45

+ 4,05

31 3,6

AI 3,15

f

f

f

+ I,65

z!I I,35

z!I I,1

f

18

&IO,5

31 8,75

I?I 7,5

+16,5

+14

&II,5

1 * 6,25 1 + 93

1

( + 5,25 1 + 8825 1

+4,5

1 + 4

+ 3,5

f

z!z 2,85

3~ 2,6

f

f

f

AI I,5

f

I!z I,05

zk 0,9

I!I 0,75

It 0,6

17

ISO 286-2 : 1988 E)

Table 8 -

Limit deviations

for holes J and K

Upper limit deviation Lower limit deviation

= ES = EI Deviations in micrometres

Basic size

K

J

mm up to and ineluding

Above

3

-

3

6

6

7

8

+2 -4

+4 -6

+6 -8

-2

-3

-4

+5 -3

k 63)

+I0 -8

0 -2,5

+0,5 -3,5

3

4

0

5

0

6 0

7

8

92)

-

0 6

-

0 10

0 -5

+ -

2 6

+ -

3 9

+ 5 - 13

+0,5 -3,5

+ 1 -5

+ -

2 7

+ 5 - 10

+ 6 - 16

+2 -6

+ -

2 9

+ 6 - 12

+ 8 - 19

-

0 14

6

10

‘;

+8 -7

+I2 -10

0 -2,5

10

18

‘;

+I0 -8

+I5 -12

-3

+I -4

+I2 -9

+20 -13

-0,5 -4,5

-6

+I -8

+ 2 - 11

+ 6 - 15

+ 10 - 23

+I4 -11

+24 -15

-0,5 -4,5

+I -6

+2 -9

+ 3 - 13

+ 7 - 18

+ 12 - 27

+I8 -12

+28 -18

+3 -10

+ 4 - 15

+ 9 - 21

+ 14 - 32

-6

+22 -13

+34 -20

+2 -13

+ 4 - 18

+ 10 - 25

+ 16 -38

18

30

30

;;

5o

+I0

-6 50

8o

+I3

-6 80

I20

+I6

0

0

120

180

+I8 -7

+26 -14

+41 -22

+3 -15

+ 4 - 21

+ 12 - 28

+ 20 -43

180

250

‘;

+30 -16

+47 -25

+2 -18

+ 5 - 24

+ 13 -33

+22 -50

250

315

+25 -7

+36 -16

+55 -26

+3 -20

+ 5 - 27

+ 16 - 36

+ 25 - 56

315

400

y

+39 -18

+60 -29

+3 -22

+ 7 - 29

+ 17 -40

+ 28 - 61

400

5oo

+33 - 7

+43 -20

+66 -31

+2 -25

+ 8 - 32

+ 18 - 45

+ 29 -68

I

.

500

630

630

800

800

1000

1 000

1 250

1 250

1 600

1 600

2 000

2 000

2 500

2500

3 150

I

9’)

1

I

I

I

I

I

I

I

0

-44

I

0 - 70

0

-50 0 0 0 - 78

-125

0 -140 0 -165

0

0

0 -195

0 -150

0

0 -230

0 -175

0 -135

0

0 -105

-110

-110

0

-66

- 92

I

-125

-90

-56

0 -280

0 -210

0 -25

0

0

-80

0 -330

1) Tolerance classes J9, JIO, etc. are symmetrical about the zero line. For these values, see JS9, JSIO, etc. 2)

Deviations for K in tolerance grades above IT8 are not defined for basic sizes greater than 3 mm.

3)

Identical with JS7.

14

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

COPYRIGHT 2003; International Organization for Standardization

102)

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

0 -40

IS0 286-2 : 1988 (El

Table 9 -

Limit deviations

for holes M and N

Upper limit deviation Lower limit deviation

= ES = EI Deviations in micrometres

Basic size

M

N

mm Above

6 10

+

up to and in,I. .A:--

3

4

5

10 18

6

7

8

9

10

3

4

5

-4-4-7 -34

- 52

- 9,5

-6,5 -IO,5

-7 -12

-

- 6 -64

-9 -II,5

-8,5 -12,5

-8 -14

-7 -77

-II -14

-10 -15

-9 -17

-15,5 -19,5

-14 -21

-

I 9

-

0+2 I2 -

I -

3 I2

-

0 I5

I - 21

-6 -42

-

4 I5

-

0 ~+ 2 I8 - 25

-7 -50

I-+ I I6

I /

7

6

I I 1 10’) / 11’)

4 I6

- 2 - 20

0 - 30

7 -16

- 4 -19

3 -25

-36

-9-5-3 -20

-23

-30

-43

-13 -24

-12 - 28

8 - 33

3 - 42 ' -

5 I3

-

I 1 91)

8

0 - 48

0

-

0

-

0 21

+ 4 - 29

-8 -60

- 4 - 20

-

0 25

+ 5 -34

-9 + -71

- 5 -24

0

-19

-30

+ 5 - 41

-15 -28

-14 -33

9 -39

-8 -23

6 - 28

-

0 35

+ 6 -48

-18 -33

- I6 -38

-9 -27

- 8 -33

0 -40

+ 8 - 55

-21 -39

+ 9 -63

30

4 I7

0 75

0 -58

0 -90

0 -70

0 -110

I I

18

-

8 - 92 I

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

i

50

80

80

120

120

180

180

250

-II -31

- 8 -37

-46

250

315

-13 -36

- 9 - 41

-

0 52

+ 9 - 72

- IO -46

-

0 57

+ II - 78

- IO -50

-63

+I1 -86

- 26 -70

- 26 -96

- 26 -136

-30 -80

-30 -110

-30 -155

c9n

I

0

0

-9 -109

-TI

0 62

-100

- 4 -50

0 - 74

-120

-10 -45

4 -58

0 - 87

-140

- 20 - 45

-12 - 52

-

4 67

-100

-25 -45

-22 -51

-14 -60

5 -77

-115

-27 -50

-25 -57

-

-30 -55

- 26 - 62

-16 - 73

5 - 94

-140

-33 -60

- 27 - 67

-17 - 80

6 -103

-155

1

141661-86

0

0

0

-50 -100

-50 -130

-50 -I75

-50 -250

800

1000

-34 -90

-34 -124

-34 -174

-56 -112

-56 -146

-56 -196

-56 -286

1 000

1 250

-40 -106

-40 -145

-40 -205

-66 -132

-66 -171

-66 -231

-66 -326

1 250

1600

-48 -126

-48 -173

-48 -243

- 78 -156

- 78 -203

- 78 -273

- 78 -388

1600

2000

-58 -150

-58 -208

-58 -288

- 92 -184

- 92 -242

- 92 -322

- 92 -462

2000

2500

-68 -I78

-68 -243

-68 -348

-110 -220

-110 -285

-110 -390

-110 -550

2500

3 150

- 76 -211

- 76 -286

- 76 -406

-135 -270

-135 -345

-135 -465

-135 -675

1) Tolerance classes N9, N10 and Nil shall not be used for basic sizes less than or equal to 1 mm.

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

0 -320

-230

800

0 -290

0

0

-219--

0 -250

-210

630

COPYRIGHT 2003; International Organization for Standardization

0

0

-I&

0 -220

-185

-114--

88

0

0

-130

0 -190

-160

I - 441-d-441 ~~~~ --I 44I -

0

0

5

0 -160

0 -360

0 -250

0 -400

ISO286-2:1988(E)

Table 10 -

Limit deviations

Upper limit deviation Lower limit deviation

for holes P = ES = EI Deviations in micrometres

Basic size

P

mm Above

up to and ineluding 3

-

3

4

5

6

7

8

9

10

-6 -8

-6 -9

-6 -10

-6 - I2

-6 - I6

-6 - 20

-6 -31

-6 -46

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

3

6

-II -13,5

-IO,5 -14,5

-'I -16

-

9 I7

- 8 - 20

- I2 - 30

- I2 -42

- I2 -60

6

IO

-14 -16,5

-13,5 -17,5

-13 -19

-12 - 21

-9 - 24

- I5 - 37

- I5 - 51

-

10

18

-17 -20

-16 -21

-15 -23

- I5 -26

- II -29

- I8 - 45

- I8 -61

- I8 -88

18

30

-20,5 -24,5

-20 -26

-19 -28

- I8 - 31

-14 - 35

-22 - 55

-22 - 74

-22 -106

30

50

-24,5 -28,5

-23 -30

-22 -33

-

21 37

- I7 - 42

- 26 -65

- 26 -88

- 26 -126

50

80

-27 -40

- 26 - 45

- 21 - 51

-32 - 78

-32 -106

80

120

-32 -47

- 30 -52

- 24 -59

- 37 - 91

- 37 -124

120

180

-37 -55

- 36 -61

-28 -68

-43 -106

-43 -143

180

250

-44 -64

-41 - 70

-33 - 79

-50 -122

-50 -165

250

315

-49 -72

- 47 -79

-36 -88

-56 -137

-56 -186

315

400

-55 -80

- 51 -87

- 41 -98

- 62 -151

- 62 -202

400

500

-61 -88

- 55 - 95

-45 -108

-68 -165

-68 -223

- 78 -122

- 78 -148

- 78 -188

- 78 -253

500

630

630

800

-88

-88

-88

-88

-138

-168

-213

-288

800

1 000

-100 -156

-100 -190

-100 -240

-100 -330

1000

1 250

-120 -186

-120 -225

-120 -285

-120 -380

1 250

1600

-140 -218

-140 -265

-140 -335

-140 -450

1600

2000

-170 -262

-170 -320

-170 -400

-170 -540

2000

2500

-195 -305

-195 -370

-195 -475

-195 -635

2500

3 150

-240 -375

-240 -450

-240 -570

-240 -780

I5 73

3

a

16 COPYRIGHT 2003; International Organization for Standardization

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

ISO286-2:1988(E)

Table 11 -

Limit deviations

for holes R

Upper limit deviation Lower limit deviation

= ES = EI Deviations in micrometres

I

Basic size

t

I Above

R

I

mm up to andineluding

3

4

3

-10 -12

-10 -13

- IO -

I4

-

3

6

-14 -16,5

-13,5 -17,5

-

I4 I9

6

10

-18 -20,5

-17,5 -21,5

IO

I8

1;

18

30

30

50

-

50

65

65

80

5

6

7

8

9

10

- IO - 20

- IO - 24

-10 -35

- IO -50

- I2 - 20

- II -23

- I5 -33

-15 -45

- I5 -63

- I7 - 23

- I6 - 25

- I3 - 28

- I9 - 41

-19 -55

- I9 -77

-21 -26

- 20 - 28

- 20 -31

- I6 -34

- 23 -50

-23 -66

- 23 - 93

710

800

-185 -235

-185 -265

-185 -310

-26,5 -30,5

-26 -32

- 25 -34

- 24 - 37

- 20 - 41

- 28 - 61

-28 -80

- IO -112

800

900

-210 -266

-210 -300

-210 -350

-32,5 -36,5

-31 -38

- 30 - 41

- 29 -45

-25 -50

-34 -73

-34 -96

-34 -134

goo

1000

1;

1:

-220 -360

- 36 -49

- 35 -54

- 30 -60

- 41 - 87

1 120

-250 -316

-250 -355

-250 -415

-38

- 37 -56

-32 -62

-43 -89

-51

80 100

100 120

120

140

140

160

160

I

180

IO I6

-46

-44

-38

-61

-66

- 73

- 51 -105

’ 2501’ 4001 1;: 1 1:: / IG

- 49

- 47 - 69

-41 - 76

-54 -108

1400

-64 -57 - 75

-56 -81

-48 -88

-63 -126

1600

-m -408

-330

-330

-455

-525

1800

-370 -462

-370 -520

-370 -600

-59

-58

-50

-83

-go

- 65 -128

1800

2000

Iz

1:

1:

- 62 - 80

-61 - 86

-53 - 93

-68 -131

2 000

2240

1:

1:

1;

2240

2500

1:

I=

I=

200

-71 - 91

-68 - 97

-60 -106

- 77 -149

200

225

- 74 -94

-71 -100

-63 -109

- 80 -152

225

250

- 78 -98

- 75 -104

-67 -113

-84 -156

250

280

- 87 -110

- 85 -117

-74 -126

-94 -175

280

315

-91 -114

-89

- 78 -130

- 98 -179

- 101 -126

- 97 -133

- 87 -144

-108 -197

355

1600

-77

180

315

1000

-121

355

400

-107 -132

-103 -139

- 93 -150

-114 -203

400

450

-119 -146

-113 -153

-103 -166

-126 -223

450

500

-125 -152

-119 -159

-109 -172

-132 -229

4

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

COPYRIGHT 2003; International Organization for Standardization

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

IS0 286-2 : 1988 (El

Table 12 -

Limit deviations

Upper limit deviation Lower limit deviation

for holes S

ES EI

= =

Deviations in micrometres

I

Basic size I 3

3

I 7

I

8

9

10

Above

I4 I8

- I4 - 20

- I4 - 24

- I4 -28

- I4 -39

- I4 -54

500

560

-

280 324

- 280 -350

- 280 -390

6

-18 -20,5

-17,5 -21,5

- I8 - 23

- I6 - 24

- I5 - 27

- I9 - 37

- I9 - 49

- I9 - 67

560

630

-

310 354

-

310 380

-

310 420

630

710

1

g

I

z

I

r5

710

800

I

z

I

z

I

z

- 35 -119

800

900

1 g

-43 -143

900

1000

1000

1120

I I

I I

I I

I I

-33,5 -37,5

-33 -39

30

50

-41,5 -45,5 I

-40 -47 I

I

I

I

I

I

I I

I I

I I

I I

65

- 32 -41

- 31 -44

- 27 -48

- 35 -68

-

-39 -50

-38 -54

-34 -59

-43 -82

-43 -105

I

80 100

80

120

100

1 12011401 I I

I

1

I I

- 47 -66

160

180

180

200

.

I

I

I

I

1 2251 2501

/

I

I

1 I

I I

) 2501 2801 I I

I

280

I I

I

-59

-59

-105

-133

-66

-64

-58

-81

-86

- 93

- 71 -125

- 71 -158

- 74 -89

-72 -94

-66 -101

- 79 -133

- 79 -166

:I:

1 3

/

I I

I I

I

I I

/

I,::

/

3

I I

1

1 120

1 ~1~:

/

I 1

I I

470 610

-

520

-

520 625

-

520 685

1 250

-580 _ 685

-

1 $

-580

1 250

1400

1;

1:

:g

1400

1 600

- 720 -798

- 720 -845

-

1600

1 800

745

720 915

-

820

-

912

-

820 970

- 820 -1050

-

920 012

-I

920 070

- 920 -1150

-100 -163

-100 -200

1800

-102 -120

-101 -126

- 93 -133

-108 -171

-108 -208

2000

2 240

-1000 -I 110

-1000 -I 175

-1000 -1280

-116 -136

-113 -142

-105 -151

-122 -194

-122 -237

2 240

2500

-I -I

-1100 -I 275

-I 100 -1380

I

I

I

I

2 000

-I

100 210

I

I I

I I

1

I I

I I

/ 1;;:1I:,“:/ 1;: 11;: 11;; 1

I I

I I

I I

-161 -193

I

I I

-150 -202

I

I I

I

I

-170 -300

-170 -251

I

I

/ 1;; / 1s 1 IE / 1;: 1 I= / I

I

I

( 1:; / I:: 11;: / 1%11;; 1

I

I

I

I I

I

(

COPYRIGHT 2003; International Organization for Standardization

-

-125

t

18

470 560

-85

1 400( 4501 I

-

-93 -118

I

I

470 526

/ 1:; 1 1;; / 1;: 1 1;: 1 1;: 1

I

430 570

-

-586

I

I

I

I

78

-

-112

-163 -186

( 3551 400( I I

-48 -

I I

315

I

-53 72

1 g

I

-53 -127

-53 -99

-

I

I

1

I

-42 -72

-54

-94

.

35 87

- 67

I I

160

140

I

/

I I

I I

I I

I

-48 -61

65

8

-

30 --

I

7

-14 -17

18

50

6

-14 -16

1 I0 / I8 11: 11;: 1 I g 1 I ;; 1 1;; 1 1; 1 1; 1 1,” )

I

up to and ineluding

3

I I

t

I

141516/

cludina -

I

S

mm

I

up to and in-

Above

1

S

I I

mm

I

Basic size

I I

I I

I I

I I

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

4

(El

lSO286-2:1988 --`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

Limit deviations

Table 13 -

Upper limit deviation Lower limit deviation

for holes T and U = =

ES EZ Deviations in micrometres

Basic size

T’)

Basic size

U

t

I .

I

IAbove1$:;1

I

6 1 6

I

I

I

1 7

/ 8 1 6 I

I

10

I

18

I

6

/

7

24

30

30

40

-44 -55

-

40

50

-50 -61

-49 - 65

- 45 - 70

-60 - 79

-55 -85

65

80

I

1 8

I 9

/ IO

-22 -27

- 28 -

-26

- 25 - 34

- 28 -50

- 30 - 26 - 41 -- 44

- 60 I - 76 I -10:

31

-

41 1 -

-3 - 41 - 74

-38 -47

65

I

I24

50

I

- I8 - 24

-30 -38

18

I

-18 -22

+-32

I I

I I

- 28 - 2E -64 -8f

-3

I I

- 41 - 41 - 93 -12E

-44 -40 -48 -48 - 57 - 61 - 81 -100

-48 - 87

-56 -67

- 55 - 71 -

-66 -77

- 65 - 61 - 70 - 81 -86 -109

- 70 - 7c -132 -17C

- 81 -100

- 76 -106

- 87 - 87 -161 - 207

-96 -115

- 91 -102 -121 -148

- 87 -133

-60 -122

1

I

-102 -176

7

560

630

-450 - 494

-450 - 520

-450 - 560

-660 - 704

-660 - 730

-660 - 770

630

710

1 E

I

2

1 g5

1;:

12

I

-

620 710

-

620 760

-

-

680 770

-

680 820

-

780 885

-

780 945

-

8do ;;g

-4

I I

I ,

900

1000

I=

1 120

-

1 000

-

-IN

-10; -222

.I

g00

1 120

1250 I

780 846

1 g I

I

I

620 676

I I

1 g I

I

I

I

I

1600

-I -I

1600

1800

1800

050 128

-1350 -I 500

-1350 -1580

-2000 -2092

-2000 -2150

-2000 -2230

2000

2240

-1500 -I 610

-1500 -1675

-1500 -1780

-2300 -2410

-2300 -2475

-2300 -2580

-1650 -1825

-1650 -1930

-2500 -2610

-2500 -2675

-2500 -2780

-1900 -2230

-2900 -3035

-2900 -3 110

-2900 -3230

-3200

-3200 -3530

-195 -235

-210 -273

-210 -310

-2IC -37G

2500

2800

-I 900 -1900 -2035 -2 110

2800

3 150

-209

-198

-218

I

I

I

-1350 -1442

-203 -228

280

I

2000

-146 -209

I

I

I

I

I

I;= I

-1850 -2080

-131 -171

250

Ifjf; I

-1850 -2000

-139 -164

-275 -304

I

-1850 -1942

180

-196 -268

-1150 -1315

150 255

-1200 -1430

160

-179 -225

-I -I

150 216

-1200 -1350

-1650 -1760

-187 -216

-I -I

-1200 -1292

2500

250

-1050 -1190

-1600 -I 795

2240

225

-1050 -1140

-1600 -I 725

-19C -35c

-249 -278

-1050 -1106

-1600 -I 678

-190 -290

-180 -252

- 940 -1080

-1050 -1245

-190 -253

-163 -209

I

- 940 -1030

I

I

-175 -215

-171 -200

-1005

t

I

I I

940 996

-1050 -I 175

-183 -208

225

I I

I

I

1400

-134 -197

200

g

710 800

-119 -159

1

8

--

-127 -152

200

7

560 IgI~:~I~:~I~

160

/

6

500

140

180

8

-x

- 41 -45 - 74 -54

51 -60 76 -99

6

531-71

- 37 - 50 43 -39 59 -64

up to and ineluding

Above

I

1

U

T

mm

mm

-2100 -2100 -2100 -3200 m-2235~-2310m-2430/-3335,-3410

1

-24’ I -2501-2991

1) Tolerance classes T5 to T8 (incl.) have not been tabulated for basic sizes less than or equal to 24 mm. It is recommended that tolerance classes U5 to U8 (incl.) be used instead. However, if tolerance classes T5 to T8 (incl.) are especially required, they may be calculated from the bases given in IS0 286-l.

19 COPYRIGHT 2003; International Organization for Standardization

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

ISO286=2:1988(E)

Table 14 -

Limit deviations

for holes V, X and

Upper limit deviation Lower limit deviation

= =

Y ‘)

ES EI Deviations in micrometres

Basic size

V2)

X

Y3)

mm up to and ineluding

Above

-

5

6

7

6

7

8

9

10

3

-

20 24

-20 - 26

-20 -30

- 20 -34

- 20 -45

- 20 -60

3

6

- 27 -32

- 25 -33

- 24 -36

- 28 -46

- 28 -58

- 28 - 76

6

10

- 32 -38

-31 -40

-28 -43

-34 -56

-34 - 70

-34 - 92

10

14

- 37 -45

-37 -48

-33 - 51

-40 -67

-40 -83

-40 -110

- 42 -50

-42 -53

-38 -56

-45 -72

-45 -88

- 45 -115

I4 ( I8 11: / 1; 1I g 1::

6

7

8

9

10

I8 1 24 11; 17: 1:: 1I :

-51 ,-60

-50 -63

-46 - 67

-54 - 87

-54 -106

-54 -138

-

59 72

-

55 76

-

63 96

-63 -115

-63 -147

24

'-61 - 70

-60 -73

-56 -77

-64 - 97

-64 -116

-64 -148

-

7' 84

-

67 88

-

75 108

- 75 -127

- 75 -159

1

30

I~~II;l~~l~~ -107

-68

- 76 - 87

- 75 -91

-71 -96

-80 -119

-80 -142

-80 -180

-

89 105

-

8!j 110

-

94 I33

-94 -156

-94 -194

- 72 - 97

- 81 -120

- 93 -104

-92 -108

-88 -113

- 97 -136

- 97 -159

- 97 -197

-

109 125

-

105 130

-

114 I53

-114 -176

-114 -214

-96

- 91

-115

-121

-102 -148

-116 -135

-111 -141

-122 -168

-122 -196

-

I38 157

-

I33 I63

-

I44 190

-114 -133

-109 -139

-120 -166

-140 -159

-135 -165

-146 -192

-146 -220

-

I68 187

-

I63 193

-

174 220

-171 -193

-165 -200

-178 -232

-178 -265

-

207 229

-

201 236

-

214 268

30

40

1;

1;

40

50

IG

-

50

65

65

80

1: 76 92

8o/ ‘O”1 ( 1;: ( 1;: 11;: ‘00 j ‘20 1

( 1;:; / 1;; / 1;:

-203 -225

-197 -232

-210 -264

-210 - 297

-

247 269

-

241 276

-

254 308

120

I 1;;

-241 -266

-233 -273

-248 -311

-248 -348

-

293 318

-

285 325

-

300 363

325 365

-

340 403

j

140

(

I --g

I ;g

140

160

-221 -246

-213 -253

-228 -291

-273 -298

-265 -305

-280 -343

-280 -380

-333 - 358

-

160

180

-245 -270

-237 -277

-252 -315

-303 -328

- 295 -335

-310 -373

-310 -410

-

373 398

- 365 -405

- 380 -443

180

200

-275 -304

-267 -313

-284 -356

-341 -370

-333 - 379

-350 -422

-350 -465

-

416 445

-

408 454

-

425 497

200

225

-301 -330

-293 -339

-310 -382

-376 -405

-368 -414

-385 -457

-385 -500

- 461 -490

-

453 499

-

470 542

503 549

-

520 592

225( 250(

1I= / :g 1I!g

-416 -445

-408 -454

-425 -497

-425 -540

- 511 -540

-

250

1 280

1

1 $

( 1:;

/ $

-466 -498

-455 -507

-475 -556

-475 -605

-571 - 603

-560 - 612

-580 - 661

280

1 315

1

/ --g

1 1:;

j rg

-516 -548

-505 -557

-525 -606

-525 -655

-

641 673

-

630 682

-

650 731

-579 -615

-569 -626

-590 - 679

-590 -730

-

719 755

-

709 766

-

730 819

3’5 ( z551

1)

5

8

355

400

400

450

450.

500

1:g j 1: 1:g -519 -555

-509

-530

-566

-619

-649 -685

-639 -696

-660 -749

-660 -800

- 809 -845

- 799 -856

- 820 -909

-582 -622

-572 -635

-595 -692

-727 -767

-717 -780

-740 -837

-740 -895

- 907 -947

- 897 -960

-I

-647 -687

-637 -700

-660 -757

-807 -847

-797 -860

-820 -917

-820 - 975

-I

- 977 -1040

-1000 -1097

987 027

920 017

Fundamental deviations V, X and Y are not provided for basic sizes greater than 500 mm.

2) Tolerance classes V5 to V8 (incl.) have not been tabulated for basic sizes less than or equal to 14 mm. It is recommended that tolerance classes X5 to X8 (incl.) be used instead. However, if tolerance classes V5 to V8 (incl.) are especially required, they may be calculated from the bases given in IS0 286-l. 3) Tolerance classes Y6 to YIO (incl.) have not been tabulated for basic sizes less than or equal to 18 mm. It is recommended that tolerance classes Z6 to ZIO (incl.) be used instead. However, if tolerance classes Y6 to YIO (incl.) are especially required, they may be calculated from the bases given in IS0 286-l.

COPYRIGHT 2003; International Organization for Standardization

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

Iso 286-2 : 1988 (El

Table 15 - Limit deviations

for holes 2 and ZA’)

Upper limit deviation Lower limit deviation

= =

ES EI Deviations in micrometres

Basic size

z

ZA

mm up to and ineluding

6

7

8

3

- 26 -32

-

3

6

- 32 -40

31 -43

35 -53

6

‘0

1;

-

-

-

10

I4 I8

gy

g

-

6

7

8

9

10

11

26 66

-

26 86

- 32 -38

-

32 42

-

32 46

-

32 57

-

32 72

-

32 92

35 -65

35 -83

-

35 110

- 39 -47

-

38 50

-

42 60

-

42 72

-

42 90

-

42 117

-

1,;

I

,;;

1:

-

E

-

;;

-

;

-

52

I

5;

-

110

26 51

;

-

11

-50 77

-50 93

-50 - 120

-50 - 160

-61 - 72

-57 75

-64 91

-64 - 107

-64 - I34

-64 - 174

-68

-53 71

-60 87

-60 - 103

-60 - 130

-60 - 170

-74 -85

-70 88

-77 - 104

-77 - 120

-77 - 147

-77 - 187

--10794

--

III90

I

1:

1

‘Z

I

‘Z

I

zy

-114 -127

-

110 131

-

118 151

-

118 170

-

118 202

-

118 24%

112 272

-143 -159

-

I39 I64

-

I48 187

-

I48 210

-

148 248

-

I48 308

- 136 -296

-175 -191

-

171 I96

-

180 219

-

180 242

- 180 -280

172 362

-

215 245

-

226 272

-

226 300

-

- 210 -400

-

263 293

.-

274 320

-

274 348

- 274 -394

- 274 -464

322 357

-

335 389

-335 - 422

-335 - 475

-

-400 -540

-400 - 620

-57

18

24

I z

-

E

I

1;

1

,g

I

1;

24

3o

I ;

I

1;

I

1;

1

1:

I

1;

22 z 2;

30

40

-107 -123

-

103 128

-

112 151

-

112 1 174 -

112 212

-

40

50

-131 -147

-

I27 152

-

136 175

-

136 I98

- 136 -236

50

65

-

161 191

-

172 218

-

172 246

-

65

80

-

I99 229

-

210 256

-

210 284

- 210 -330

80

100

-

245 280

-

258 312

-

258 345

-

258 398

-

258 478

-

100

120

-

297 332

-

310 364

-

310 397

-

310 450

-

310 530

-387 - 422

-400 - 454

-400 -487

-

350 390

-

365 428

-

365 465

-

365 525

-

365 615

- 455 -495

- 470 -533

-

470 570

-

470 630

-

470 720

-440

-

415 478

-

415 515

-

415 575

-

415 665

- 520 -560

-

535 598

-

535 635

-

535 695

-

535 785

-465 - 715

-585 - 625

-600 - 663

-600 - 700

-600 -760

-600 -850

120

140

140

160

-400

160

180

- 450 -490

-465 - 528

180

200

- 503 -549

-

200

225

- 558 -604

225

250

250

280

280

315

315

355 400

450

450 500

226 346

-

226 416

335 555

520 705

-

520 810

- 653 -699

-

670 742

-

670 785

- 670 -855

- 670 -960

- 575 -647

- 575 -690

-

575 760

-

575 865

-

723 769

-

740 812

-

740 855

-

- 740 -1030

-623 -669

-640 - 712

-640 - 755

-640 - 825

-640 - 930

- 803 -849

-

820 892

-820 - 935

-820 -1005

-I

-690

920 001

-I

920 050

-I

920 130

- 920 -1240

ooo 130

-I -I

ooo 210

-1000 -I 320

150 380

-1150 -I 510

-

740 925

820 110

-

742

-

710 791

-

710 840

-

710 920

-I

710 030

-900 - 952

-I

-

770

-

790 871

-

790 920

- 790 -1000

-I

790 110

-980 -I 032

-1000 -1081

-I -I

879 936

-

900

-

900

-

900

-

900

-

989

-I

040

-I

130

-1260

-I 129 -1186

-1150 -1239

-1150 -1290

-I -I

979 036

-loo0 -I 089

-I -I

ooo 140

-1000 -1230

-I ooo -1360

-I 279 -1336

-1300 -1389

-1300 -1440

-1300 -1530

-1300 -1660

077

-1100 -I 197

-1100 -I 255

-1100 -1350

-1100 -1500

-I 427 -1490

-1450 -1547

-1450 -1605

-1450 -1700

-1450 -1850

-1250 -1347

-1250 -1405

-1250 -1500

-1250 -1650

-1577 -1640

-1600 -1697

-1600 -I 755

-I 600 -1850

-I 600 -2000

-I

400

-465 - 625

-

- 180 -340

-

-

355

520 592

-465 - 565

172 292

I

520 635

-822

1)

26 40

10

-43 61

-47

-58 14

26 36

-

9

-I -I

140

-1227 -1290

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

Above

Fundamental deviations Z and ZA are not provided for basic sizes greater than 500 mm.

:

21 COPYRIGHT 2003; International Organization for Standardization

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

IS0 286-2 : 1988 E)

Table 16 -

Limit deviations

for holes ZB and ZC’)

Upper limit deviation Lower limit deviation

= =

ES EZ Deviations in micrometres

Basic size

ZB

zc

mm

, -

3

3

6

6

I0

7

8

9

-40 50

-40 -54

-40 -65

-

I

i

z

;

z

;

I

,g

-

g

-

;

-;;

-

67

-

-89

-

67 IO3

-

67 125

-

67 157

-

91 106

-

97 119

-

z

IO

11

-40 -80

7

8

9

IO

11

-40

-60

-60

-60

-60

-100

-70

-74

-85

-

100

-

120

1,;

:

,;

:

,g

97 I33

-

97 155

-

97 187

-60

10

I4

I

1;

I

1;

I

,g

1

1;

I

2;

-

123 141

-

130 157

-

130 173

-

130 200

-

130 240

14

18

-

101 119

-

108 135

-

IO8 151

-

108 178

-

IO8 218

-

I43 161

-

150 I77

-

150 193

- 150 -220

-

150 260

18

24

-

128 I49

-

136 I69

-

I36 I88

-

I36 220

-

I36 266

-

180 201

-

I88 221

-

I88 240

-

I88 272

-

I88 318

24

30

-

152 173

-

160 193

-

160 212

-

160 244

-

160 290

-

210 231

-

218 251

-

218 270

-

218 302

- 218 -348

30

40

-

191 216

-200

-

-

239

-

200 262

- 200 -300

-

200 360

- 265 -290

-

274 313

-

274 336

-

274 374

- 274 -434

242 281

- 242 -304

-

242 342

-

242 402

-

-

325 364

-

325 387

-

325 425

-

325 485

300 420

- 300 -490

-394 - 424

-405 - 451

-

405 479

-

405 525

-

405 595

-469 -499

-480 - 526

-

480 554

-480 -600

-480 - 670

40

50

-

233 258

-

50

65

-

289 319

-300 -346

-300 - 374

-

65

80

-349

-360

-

379

-406

- 360 -434

- 360 -480

-

360 550

316 341

80

100

-

432 467

- 445 -499

-445 -532

-445 -585

- 445 -665

-

572 607

-585 -639

-

585 672

-585 - 725

-585 - 805

100

120

-

512 547

-

525 579

-

525 612

-

525 665

-

525 745

-

677 712

-690 - 744

- 690 -777

-690 - 830

-690 - 910

120

140

-

605 645

-

620 683

-

620 720

-

620 780

-

620 870

-

785 825

-800 -863

-800 -900

-800 -960

-800 -1050

140

160

1 !g

-

700 763

- 700 -800

- 700 -860

-

700 950

-

885 925

-900 -963

-900 -I ooo

-900 -1060

-900 -1150

160

180

-

- 780 -843

- 780 -880

- 780 -940

- 780 -1030

-I

985 025

-1000 -1063

-1000 -I 100

-1000 -I 160

-1000 -1250

180

200

1 g

-1133 -I 179

-I 150 -1222

-1150 -I 265

-I 150 -1335

-1150 -1440

200

1)

up to and ineluding

225

765 805

Ig

-880

-880

-880

-880

-

-995

-1065

-I

952

170

-960

-960

-960

-960

-1032

-I

-I

145

-1250

-I -I

279

-1250 -1322

-1250 -I 365

-1250 -1435

-1250 -1540

075

233

225

250

-1033 -I 079

-1050 -1122

-1050 -1165

-1050 -I 235

-1050 -1340

-1333 -I 379

-1350 -1422

-1350 -1465

-1350 -1535

-1350 -1640

250

280

-1180 -1232

-I -I

-1200 -1330

-1200 -I 410

-1200 -1520

-I 530 -1582

-I -I

550 631

-I 550 -1680

-1550 -1760

-1550 -1870

280

315

-1280 -1332

-1300 -1381

-1300 -I 430

-1300 -I 510

-1300 -I 620

-I -I

-1700 -I 781

-1700 -I 830

-1700 -I 910

-1700 -2020

315

355

-I -I

-1500 -I 589

-1500 -I 640

-I -I

-I 500 -1860

-I 879 -1936

-1900 -1989

-1900 -2040

-I 900 -2130

-1900 -2260

355

400

-1629 -1686

-1650 -1739

-1650 -1790

-1650 -1880

-1650 -2010

-2079 -2 136

-2100 -2189

-2100 -2240

-2100 -2330

-2100 -2460

400

450

-1827 -1890

-1850 -1947

-I 850 -2005

-1850 -2100

-1850 -2250

-2377 -2440

-2400 -2497

-2400 -2555

-2400 -2650

-2400 -2800

450

500

-2077 -2140

-2100 -2 197

-2100 -2255

-2100 -2350

-2100 -2500

-2577 -2640

-2600 -2697

-2600 -2755

-2600 -2850

-2600 -3cnO

479 536

200 281

500 730

680 732

Fundamental deviations ZB and ZC are not provided for basic sizes greater than 500 mm.

22 COPYRIGHT 2003; International Organization for Standardization

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

Above

1s0 286-2 : 1988 (El

Table 17 - Limit deviations

for shafts a, b and cl)

Upper limit deviation Lower limit deviation

= es = ei Deviations in micrometres

Basic size

a21

C

b2)

mm Above

up to and in&ding 32)

-

9 -

10

11

12

13

8

9

IO

11

12

13

8

9

10

11

12

270 295

-

270 310

-

270 330

-

270 370

-

270 410

-140 -154

-140 -165

-

140 180

-

140 200

-

140 240

-140 - 280

-60 - 74

-60 - 85

-60 -100

-60 -120

-

60 160

- 70 - 88

- 70 -100

- 70 -118

- 70 -145

-

70 190

3

6

- 270 -300

-

270 318

-

270 345

-

270 390

-

270 450

-140 -158

-140 -170

-

140 188

-

140 215

-

140 260

-

6

IO

-280 - 316

-280 - 338

-

280 370

-

280 430

-

280 500

-150 -172

-150 -186

-

150 208

-

150 240

-

150 300

-150 - 370

-80 -102

-80 -116

-80 -138

-80 -170

-

80 230

IO

I8

-290 -333

-290 -360

- 290 -400

-

290 470

-

290 560

-150 -177

-150 -193

-

150 220

-

150 260

-

150 330

-

150 420

- 95 -122

- 95 -138

- 95 -165

- 95 -205

-

95 275

18

30

-

300 352

-

300 384

-

300 430

-

300 510

-

300 630

-160 -193

-160 -212

-

160 244

-

160 290

-

160 370

-

160 490

-110 -143

-110 -162

-110 -194

-110 -240

-

110 320

30

40

-

310 372

-

310 410

-

310 470

-

310 560

-

310 700

-170 -209

-170 -232

-

170 270

-

170 330

-

170 420

-

170 560

-120 -159

-120 -182

-120 -220

-120 -280

-

120 370

40

50

- 320 -382

-

320 420

-

320 480

-

320 570

-

320 710

-180 -219

-180 -242

-

180 280

-

180 340

-

180 430

-

180 570

-130 -169

-130 -192

-130 -230

-130 -290

-

130 380

50

65

1 z

1 z

1;;

1;;

1 ;

65

1 z

1 2

-190

-190

-

‘90

-

‘90

-

‘90

-

‘90

-236

-264

-

310

-

380

-

490

-

650

-14

-140

-214

-260

_

360 434

1

z

I

;;

1

&o

1

;6

1;:

1;;

I

;;

1

;;

1

2;

1

2;

1;;

-150 -224

-1% -270

-1% -340

-

1% 450

'00

1

z

1

s

I

fig

I

g

I

z

42;

:g

I

;2

I

z

I

22;

I

72

-170 -224

-170 -257

4;;

-170 -390

I

;;

loo

120

-

410 497

-

410 550

-

410 630

-

410 760

-

410 950

-240 -294

-240 -327

-

240 380

-

240 460

-

240 590

-

240 780

-180 -234

-180 -267

-180 -320

-180 -400

-

180 530

120

140

I

2

1 z

I

3

I

z

-

460

1;;;

1;;

I

;i

I

;;

1 2;

I

z

1;;

1;

1;;

1;;

I

g

140

160

-

520 620 1 -

520 680

-

520 770

-

520 920

- 520 -1 150

-280 -343

-280 -380

-

280 440

-

280 530

-

280 680

-

280 910

-210 -273

-210 -310

-210 -370

-210 -460

-

210 610

160

180

I

:

1

y&f'

1

z;

I

E

- 580 -1210

---ii

1;;;

I

;;;

I

3:

1

,":;

1

;

1;;

1;;

1:;

12:

1

;;

180

2oo

1

g

1

r5

I

g

- 660 -1120

--1380 660

:z

:gFj

I

z5

I

g

I

z

- 340 -1060

1;;

1;;

1:;

1;;

I

;;

200

225

-

740 855

-

740 925

- 740 -1 030

- 740 -1200

- 740 -1460

-380 -452

-380 -495

-

380 565

-

380 670

-

380 840

- 380 -1100

-260 -332

-260 -375

-260 -445

-260 -550

-

260 720

225

250

-

820 935

- 820 -1005

- 820 -1 110

- 820 -1 280

- 820 -1540

-420 -492

-420 -535

-

420 605

-

420 710

-

420 880

- 420 -1140

-280 -352

-280 -395

-280 -465

-280 -570

-

280 740

250

280

-

920 -1050

-

920 -1 130

-

920 -1240

-

920 -1440

-

920 -1 730

-480 -561

-480 -610

-

480 690

-

480 800

- 480 -1000

- 480 -1290

-300 -381

-300 -430

-300 -510

-300 -620

-

300 820

280

315

-1050 -1180

-1050 -1260

-1050 -1 370

-1050 -1 570

-1050 -1860

-54.0 -621

-540 -670

- 540 -750

- 540 -860

- 540 -1060

- 540 -1350

-330 -411

-330 -460

-330 -540

-330 -650

-

330 850

315

355

-1200 -1340

-1200 -1430

-1200 -1560

-1200 -1770

-1200 -2090

-600 -689

-600 -740

-600 - 830

-600 - 960

-600 -1170

-600 -1490

-360 -449

-360 -500

-360 -590

-360 -720

-

360 930

355

400

-1350 -1490

-1350 -1580

-1350 -1710

-1350 - 1 920

-1350 -2240

-680 -769

-680 -820

-680 - 910

-680 -1040

-680 -1250

-680 -1570

-400 -489

-400 -540

-400 -630

-400 -760

-400 - 970

400

450

-1500 -1655

-1500 -1750

-1500 -1900

-1500 -2130

-1500 -2470

-760 -857

-760 -915

- 760 -1 010

- 760 -1160

- 760 -1390

- 760 -1730

-440 -537

-440 -595

-440 -690

-440 -840

- 440 -1070

450

500

-1650 -1805

-1650 -1900

-1650 -2050

-1650 -2280

-1650 -2620

-840 -937

-840 -995

-840 -1090

-840 -1240

-840 -1 470

-840 -1810

-480 -577

-480 -635

-480 -730

-480 -880

-480 -1110

80

80

1 2

140 320

-1090

I)

Fundamental deviations a, b and c are not provided for basic sizes greater than 500 mm.

2)

Fundamental deviations a and b shall not be used for any standard tolerance grades in basic sizes less than or equal to 1 mm.

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

COPYRIGHT 2003; International Organization for Standardization

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

23

IS0 286-2 : 1988 (El

Table 18 -

Limit deviations

for shafts cd and d

Upper limit deviation Lower limit deviation

= es = ei Deviations in micrometres

Basic size

cd’)

d

mm up to and ineluding 3

-

3

6

6

10

10

18

18

5

6

7

8

9

-34

-34

-34

-34

-34

- 34

-38

-40

-44

-48

-59

- 74

6

7

8

- 20 - 26

- 20 -30

- 20 -34

-

20 45

-

20 60

-

20 80

- 20 -120

-

20 160

-

30 60

-

30 78

-

30 105

- 30 -150

-

30 210

-

;

5

10 -

20 24

9

10

11

12

13

-46

-46

-46

-46

-46

- 46

- 30

-51

-54

-58

-64

-76

-94

-35

-30 -38

-30 -42

-30 -48

1:

1;

1;

1;

1:

-56

12

1:

1;

1;

-50 -58

-50

-50

-50

-

50

-

50

-

50

-50

-

50

-61

-68

-77

-

93

-

120

-

160

-230

-

320

74

-65 -78

-65 -86

- 65 -98

-

65 117

-

65 149

-

65 195

- 65 -275

-

65 395

@O 240

-80 -330

-

80 470

-114

30

-65 -

-

-

40

-

98

-

-

40

130

-40

-190

-

-

40

260

30

50

- 80 -91

-80 -96

-80 -105

-80 -119

-

80 142

-

80 180

-

50

80

-100 -113

-100 -119

-100 -130

-100 -146

-

loo 174

-

100 220

- loo -290

-100 -400

-

100 560

80

120

-120 -135

-120 -142

-120 -155

-120 -174

-

120 207

- 120 -260

- 120 -340

-120 -470

-

120 660

120

180

-145 -163

-145 -170

-145 -185

-145 -208

-

145 245

-

-

145 395

-145 -545

-

145 775

180

250

-170 -190

-170 -199

-170 -216

-170 -242

-

170 285

- 170 -355

- 170 -460

-170 -630

- 170 -890

250

315

-190 -213

-190 -222

-190 -242

-190 -271

-

190 320

-

190 400

-

190 510

-190 -710

- 190 -1000

315

400

-210 -235

-210 -246

-210 -267

-210 -299

- 210 -350

- 210 -440

-

210 570

-210 -780

- 210 -1 loo

400

500

-230 -257

-230 -270

-230 -293

-230 -327

- 230 -385

- 230 -480

-

230 630

-230 -860

- 230 -1200

-370

-415

-

1000

-320 -410

-320 -460

- 320 -550

- 320 -680

- 320 -880

1000

1 250

-350 -455

-350 -515

-

-

- 350 -1 010

1 250

1600

-390 -515

-390 -585

-390 - 700

-390 -890

- 390 -1170

1 600

2000

-430 -580

-430 -660

- 430 -800

-430 -1 030

-430 -1350

2000

2500

-480 -655

-480 -760

-480 - 920

-480 -1180

-480 -1580

2500

3 150

-520 -730

-520 -850

- 520 -1060

- 520 -1380

- 520 -1 870

145 305

630 800 800

i-

490

350 610

350 770

1) The intermediate fundamental deviation cd is provided primarily for fine mechanisms and horology. If tolerance classes involving this fundamental deviation in other basic sizes are required, they may be calculated in accordance with IS0 286-l.

24 COPYRIGHT 2003; International Organization for Standardization

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

Above

IS0 286-2 : 1988 (El

Table 19 -

Limit deviations

for shafts e and ef

Upper limit deviation Lower limit deviation

= es = ei Deviations in micrometres

Basic size

e

mm up to and ineluding

Above

5

6

7

8

9

10

3

4

5

6

7

8

9

10

3

-

14 18

- 14 - 20

- 14 - 24

- 14 -28

- 14 -39

-

14 54

-10 -12

-10 -13

-10 -14

-10 -16

-10 -20

-10 -24

-10 -35

-10 -50

6

- 20 - 25

- 20 - 28

- 20 -32

- 20 -38

- 20 -50

-

20 68

-14 -16,5

-14 -18

-14 -19

-14 -22

-14 -26

-14 -32

-14 -44

-14 -62

6

10

- 25 -31

- 25 -34

- 25 -40

- 25 - 47

- 25 -61

-

25 83

-18 -20,5

-18 -22

-18 -24

-18 -27

-18 -33

-18 -40

-18 -54

-18 -76

10

I8

- 32 -4.0

- 32 -43

- 32 -50

- 32 -59

- 32 - 75

-

32 102

18

3o

1:

1;

1;

1;.

1;

1,;

30

50

1;

1;

1;

1;

50

*O

1;

- 60 - 79

-60 - 90

3 ~ I

-50

-

50

-112

-

150

-60 -106

-60 -134

-

60 180

80

120

- 72 -87

- 72 -94

- 72 -107

- 72 -126

- 72 -159

-

72 212

120

180

- 85 -103

- 85 -110

- 85 -125

- 85 -148

- 85 -185

-

85 245

180

250

-100 -120

-100 -129

-100 -146

-100 -172

-100 -215

-

loo 285

250

315

-110 -133

-110 -142

-110 -162

-110 -191

-110 -240

-

110 320

315

400

-125 -150

-125 -161

-125 -182

-125 -214

-125 -265

-

125 355

400

500

-135 -162

-135 -175

-135 -198

-135 -232

-135 -290

- 135 -385

500

630

-145 -189

-145 -215

-145 -255

-145 -320

-

145 425

630 1*O” 1 12: / xi / 2: 1zl 11ii 1 1 1 1 / 1 I I I I I I I I I I I I I II 125o /1600 1 / I 1 000

1 250

’ 6oo / 2ooo 1

2ooo125001 2500

3 150

j 1;: / 1:; 1 :g 1 1;: 1 =d -290 -425

-290 -500

-290 -620

-290 -830

- 290 -1150

I

I

/ I

/ I

1 1 / I I I

-

1) The intermediate fundamental deviation ef is provided primarily for fine mechanisms and horology. If tolerance classes involving this fundamental deviation in other basic sizes are required, they may be calculated in accordance with IS0 286-l.

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

COPYRIGHT 2003; International Organization for Standardization

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

Is0 286-2 : 1988 (El

Table 20 -

Limit deviations

for shafts f and fg

Upper limit deviation Lower limit deviation

= es = ei Deviations in microme

Basic size

f

fg’)

mm Above

up to and ineluding

.

. 3

-

3

6

6

10

4

5

6

7

8

9

10

-6 -8

-6 -9

-6 -10

-6 - 12

-6 - 16

-6 - 20

-6 -31

-6 -46

-10 -12,5

-10 -14

-10 -15

- 10 -18

- 10 -22

- 10 -28

- 10 -40

-10 -58

-6 - 8,5

-6 -10

-6 -11

-6 -14

-6 -18

-6 -24

-6 -36

-6 -54

-8 -IO,5

-8 -12

-8 -14

-8 -17

-8 -23

-8 -30

-8 -44

-8 -66

-13 -19

- 13 -22

- 13 - 28

- 13 -35

- 13 -49

-13 - 71

-16 -24

- 16 -27

- 16 -34

- 16 -43

-

16 59

- 16 - 86

18

30

-20 -24

-20 -26

-20 -29

- 20 - 33

- 20 -41

- 20 -53

- 20 - 72

- 20 -104

30

50

-25 -29

-25 -32

-25 -36

- 25 -41

- 25 -50

- 25 -64

-

- 25 -125

50

80

-30 -38

-30 -43

- 30 - 49

- 30 - 60

-30 - 76

-30 -104

80

120

-36 -46

-36 -51

- 36 -58

- 36 -71

- 36 -90

- 36 -123

120

180

-43 -55

-43

-43

-43

-43

-43

-61

-68

-83

-106

-143

-50 -64

-50

-50

-50

-50

-50

-70

-79

-96

-122

-165

-56

-56

-56

-56

-56

-88

-108

-137

-185

- 62 -98

- 62 -119

- 62 -151

- 62 -202

400

-62 -80

-62 -87

400

500

-68 -88

-68

-68

-68

-68

-68

-95

-108

-131

-165

-223

- 76 -120

- 76 -146

- 76 -186

- 76 -251

t 500 .-

630 800

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

315

630 800 1000

-80

-80

-130

-160

-80 -205

-80 -280

-86

- 86 -176

-86 -226

-86 -316

-142

-98

-98

-98

-98

-164

-203

-263

-358

1600

-110 -188

-110 -235

-110 -305

-110 -420

1600

2000

-120 -212

-120 -270

-120 -350

-120 -490

2000

2500

-130 -240

-130 -305

-130 -410

-130 -570

2500

3 150

-145 -280

-145 -355

-145 1 ,-475

-145 1 -685

1000

1250

1250

1

IO -4 -44

-13

-79

9 -4 -29

-17

-56

8 -4 -18

-13

-72

7 -4 -14

-16 -21

315

6 -4 -10

-16 -19

250

5 -4 -8

18

250

I

4 -4 -7

-15,5

25 87

3 -4 -6

10

180

I

3

I

I

I

i

I

I

I

1) The intermediate fundamental deviation fg is provided primarily for fine mechanisms and horology. If tolerance classes involving this fundame deviation in other basic sizes are required, they may be calculated in accordance with IS0 286-l.

COPYRIGHT 2003; International Organization for Standardization

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

IS0 286-2 : 1988 (E)

Table 21 -

Limit deviations

Upper limit deviation Lower limit deviation

for shafts g = es = ei Deviations in micrometres

Basic size

g

mm Above

-

up to and including

3

3

4

5

6

7

8

9

10

-2 -4

-2 -5

-2 -6

-2 -8

-2 - 12

-2 - 16

-2 -27

-2 - 42

.- 4 -6,5

-4 -8

-4 -9

-4 - 12

-4 -16

-4 -22

-4 -34

-4 - 52

-5 - 7,5

-5 - 9

-5 -11

-5 - 14

-5 - 20

-5 - 27

-5 -41

-5 -63

-6 -9

-6 -11

-6 -14

-6 - 17

-6 -24

-6 -33

-6 -49

-6 - 76

-7 -13

-7 -16

-7 - 20

-7 -28

-7 -40

-7 -59

-7 - 91

-9 -16

-9 -20

-9 -25

-9 -34

-9 -48

-9 -71

-9 -109

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

18

30 '-7

30

50

50

80

-10 -18

-10 -23

- 10 -29

- 10 -40

- 10 -56

80

120

-12 -22

-12 -27

- 12 -34

- 12 -47

- 12 -66

120

180

-14 -26

-14 -32

- 14 -39

- 14 -54

- 14 -77

180

250

-15 -29

-15 -35

- 15 -44

- 15 - 61

- 15 - 87

250

315

-17 -33

-17 -40

- 17 - 49

- 17 -69

- 17 -98

315

400

-18 -36

-18 -43

- 18 - 54

- 18 - 75

- 18 -107

400

500

-20 -40

-20 -47

- 20 -60

- 20 -83

- 20 -117

-22 -66

-22 - 92

-22 -132

- 24 - 74

- 24 -104

- 24 -149

- 26 - 82

- 26 -116

- 26 -166

~ - 11 -9 -13

a

1 000

1 250

- 28 -94

- 28 -133

- 28 -193

1 250

1 600

- 30 -108

- 30 -155

- 30 -225

1600

2 000

- 32 -124

- 32 -182

- 32 -262

2 000

2500

-34 -144

-34 -209

-34 -314

2500

3 150

-38 -173

-38 -248

-38 -368

COPYRIGHT 2003; International Organization for Standardization

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

Is028692

:1988(E)

Table 22 -

Limit deviations

for shafts h

Upper limit deviation Lower limit deviation

.

= es = ei h

1

2

4

3

5

6

7

8

9

IO

II

I2

I3

141)

161)

151)

17

18

Deviations (Im 3')

-

3

0 -0,8

6

-y

0 1,2-2

-

‘8

10 18

3o

30

50

50

*O

- 4

0 -3

-8

-;

2j

0

0

-I,5

- 2,5 - 4

0

- 7

‘20 ‘80

120 180

250

-;

-3”

-;

-;

0 - 4

0 - 6

-10

0 -3,5

-

0 5

0 - 8

-12

;

-1;

,

250

315

-

;

315

400

-;

500

-12

I

F;nfl ' "'

VW”

vv”

I

630

-;

1000

-11

1 250

0

1600 2 000

2 000

2500

0

1)

0 0

0 -65

0 -55 0

0 I -50

0 -55

-46

0

0 -36

0 -47

-39

0 -35 -41

0 -26

0

0

0

0

0 - 0,6

-

0 8

-

0 12

-

0 18

0 - 30

0 - 48

-

0 75

0 -0,12

0 -0,18

0 -0,3

0 -0,48

0 - 0,75

0 9

0

-

-15

0 - 36

0 - 58

-

0 90

0 -0,15

0 - 0,22

0 -0,36

0 -0,58

-

0 11

0

-

-

0 - 70

-

0 110

0 -0,18

0 -0,27

0 -0,43

0 -0,7

-

0 13

-21

-33

-52

0 - 84

-

0 130

0 -0,21

0 -0,33

0 -0,52

0 -0,84

0 16

0 - 25

0 - 39

-

0 62

0

-

-100

-

160

0 - 0,39

0 -0,62

0 19

0 - 30

0 - 46

0 - 74

0

0

-

-120

-

190

-0,3

0 - 0,46

0 -22

0 - 35

-

0 54

0 - 87

-140

-

0 220

0 -0,35

0 - 25

0 - 40

0 - 63

-100

-

0 250

0 - 29

0 - 46

-

0 72

-115

-

0 290

-

320

-

360

-

400

-68

0 -22 0 18

0 -27

0

-52

0 - 36

-

-43 0

0

0

-32

0 0 0 -160

0

0

0 -185

0 -130

0 57

0 - 89

-140

0

0 - 97

-155

0

0

0

-81

-63

0

0 -210

0

0

0 -230

0

0

0 -250

0 I,2

-

0 0,9

-

0 1,5

0 - 2,2

-

0 1,l

-

0 1,8

0 - 2,7

-

0 I,3

-

0 2,l

0 - 3,3

-1

-

0 I,6

0 - 2,5

0 - 3,9

0 -0,74

0 -I,2

-I,9

-3

0 - 4,6

0 -0,54

0 -0,87

0 -I,4

0 - 2,2

0 - 3,5

0 - 5,4

0 -0,4

0 -0,63

0 -1

0 -I,6

0 - 2,5

0 - 4

0 - 6,3

0 -0,46

0 -0,72

0 -1,15

0 -I,85

0 - 2,9

0 - 4,6

0 - 7‘2

0

0 -0,81

0 -I,3

0 -2,'

0 - 3,2

-

0 5,2

0 - 8,l

0 -0,89

0 -I,4

0 -2,3

0 - 3,6

-

0 5,7

0 - 8,9

0 - 0,97

0 -1,55

0 -2,5

0 - 4

-

0 6,3

0 - 9,7

-0,25

-0,52

0 -0,57

0 -0,63

0

0

/ - 7: 1 -11:

0 50

0 - 80

-125

-

0 56

0 - 90

-140

-105

0 - 78

-125

0 - 92

-150

0 -96

-135

0

0

0

-440 -540

0

560

-0,9

-

660

-

780

0

0

-

920

-I,5

0 0

0

0 -700

0

0 -330

0 -

0 -600

0

0

0 -0,8

0 -500

-370

-280 0

-210

0

0 -230

0 500

0 -420

-1100 0

0 -860

-;,7

0

0

-310

hi/

0

-360

-260 0

1-

-320 0

0

-195

-175

0

-230

-165

0

/ -28;

-200 0

0

0 -110

1 -17; 0

0

0 - 66

0

0

1

-

-78

0 I,8

-

I

,

0 -40

-33

-29

-25

0

0

0

0

0 -0,4

0 -36

-28

-24

-21

-18

0

0

0

0 -0,25

/I - :

0 -25

-21

-18

-15

1600

0

0

0 -0,14

-40

1 -3;

0 -18

-15

0 -0,'

0

-27

/ -:

0 -13

0 60

O

O -20

1 -1:

0

-13

1 250

O

-25

2)

" - i / -1:

-

0

O

O -18

-15

II -

0 - 40

O -23

r

800 1 000

-2;

O

O O

-10

800

-18

-16

-;

-10

I

0

0 O

-13

400

-15

O

_

0 - 25

0

0

-14

-;

0 14

O

0 -2,5

-;5

-

0 -11 -13

80

0 10

0

0 -5

I

0

-

O _;

O

0

-;5-;5-; I

0 6

-;

I,5 - 2,5

0 -1,2-2

-4

I

O -

-

0

0 -3

-y,-;,-y I

10 -;

6

0

mm

I

-1350

0 -I,05

0 -I,25

/ -:,I

/ -:.,,

1 -;,8

0

/ - :,4

1 - ;

-2

0 -3,2

-5

-8

0 -I,4

0 -2,3

0 -3,6

0 - 5,6

-

0 -I,65

0 -2,6

0 -4,2

0 - 6,6

0 -IO,5

0 -16,5

0 - I,95

0 -3,l

0 -5

0 - 7,8

0 -12,5

0 - 19,5

0 -2,3

0 -3,7

0 -6

0 - 9,2

-15

-23

0

-28

0

0

0 -12,5

0 -I,25

0

0

1 -1;

0 9

0 -14

0

-I,75

-2,8

0 -4,4

-7

0 -11

0 -17,5

0 -2,l

0 -3,3

0 -5,4

0 -8,6

0 -13,5

-21

0 0

0

0 -33

Tolerance grades IT14 to IT16 (incl.) shall not be used for basic sizes less than or equal to 1 mm.

2) The values given in the frame, for tolerance grades IT1 to IT5 (incl.), for basic sizes greater than 500 mm and less than or equal to 3 150 mm, are included for experimental use.

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

COPYRIGHT 2003; International Organization for Standardization

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

+0,75

630

500

f34

+43

&39

23

31,5

+67,5

Ik55

k46

k39

52,5

16,5

+ 26

k 21,5

+ 18

+ 15

31 12,5

1 AI 23

77,5

+ 87,5

f

+ 70

65

Ik 57,5

31 42

1 31 60

, +50

+675

f.550

+460

z!I390

k330

f1,05

+0,875

+0,75

+0,625

+0,525

&I,4

f1,15

f 0,975

+0,825

1 *0,7

1 +0,45

1 f280

*0,55

f0,485

+0,445

, +0,405

1 +0,4 - 1 kO.625

+0,35

+0,315

&0,285

, f0,26

f0,36

kO,315

1 +0,27

1 +0,23

, +0,195

+0,165

+0,135

1 +250

AI220

f200

A1180

, _+I60

+0,23

kO,2

1 +0,175

1 +0,15

, +0,125

f0,105

I!I 0,09

fO,ll

I!I 0,09

+0,07

13

L-2,2

+I,85

&I,55

+1,3

1 f1,15

1 +I

f0,875

+0,775

+0,7

, f0,65

+0,575

+0,5

1 +0,435

1 _+0,37

, f0,31

f0,26

+0,215

+0,18

f0,15

&0,125

143)

pm.

f430

+350

+300

k250

+210

! f'60 1 +I80

f140

L-125

&I15

, +105

f145

+I25

1 &I10

1 + 95

, +80

31 65

AI 55

+0,075

+0,06

-t-o,05

12

; this is to be interpreted as es = +x and ei = -x, e.g. ti$

f270

f220

+I85

+155

Ii130

80

k 92,5

f

37,5

30

f: 45

f

f

11

f2,7

+I65

+140

+115

I!I 97,5

I!I 82,5

1 + 62,5 1 +'o() 1 + 70 1 f115

AI 55

I!I 48,5

k 44,5

29

Ik 35

f

IL 24

43,5 1 31 70

+50

, I!I 40,5 , f

It 36

f31,5

1 f

1 k 37

10

Ik 20

Deviations

9

+I,65

+105

III 87,5

k 75

L 62,5

f

1 + 40 1 k 45

f

I!I 28,5

, 31 26

f

Ik 20

11 +25 11 f28 +33

f

z!I 13,5

1 r-t 17,5 1 + 27

AI 35

f20

&I8

+I6

IO,5

9

7

AI 11

+

Ik

8

12,5 , 31 19,5 , IL 31

1 L- 15

, f

f

AI 9

+22

,

+14,5

+12,5

1 &II

6

z!I 7,5

+

z!z 5

7

+4,3

k3.5

+3

+2,5

k2,l

1 +I,8

The values in the frame, for tolerance grades IT1 to IT5 (incl.), for basic sizes greater than 500 mm and less than or equal to 3 150 mm, are included for experimental use.

4)

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

Tolerance grades IT14 to IT16 (incl.) shall not be used for basic sizes less than or equal to 1 mm.

3)

COPYRIGHT 2003; International Organization for Standardization

0,75

2,6

2,3

3,5

3,15

45

6,25 8.75 1 HO,5 I

f

z!z 7,5

f

k 5,25

I&

1 31 4

f

f

AI 2,85

I f

f

18

1,'

f

f

9,75

( f16,5 I

+14

f11,5

f

k 8,25

1

I

6.25 1

+ 5,5

I& 4,85

* 4,45

I+7

1

4,05 1

+ 3,6

zk 3,15

1 + 2.3

1 f

1

I,95 .

I,65

zk I,35

f

+ 0,9

, f ',75 1

I,5

I!I 2

1 *

1 f

. k I,25

I!I I,05

AI 0,9

f

IL 0,6

17

of 05 pm may possibly be

1 +6,75 I

k5.5

f4,6

f 3,9

_+3,3

1 f2,8

+2,2 1 k2.5

+1,4 1 k1.6

f2

f1,8

&I,15 &I,25

I f1,6

&I,45 , +I,05

&I,25 I!I 0,925

1 f','

1 +0,95

+0,8

1 +0,7

1 +0,6

f0,65 , +0,8

f0,42

L-0,55

+0,45

f0,375

+0,3

163)

, f0,5

+0,35

f 0,29

f0,24

+0,2

mm

153)

I IT The table gives the exact values derived from I!I -, either in micrometres or millimetres. For tolerance classes js7 to jsl 1 (incl.), the values with decimal fractions ‘) L

f25

f20,5

4)

I!I 8

+ 6,5

5,5

1 31 9,5

,

f

Ii 4,5

k 4

+3

In order to avoid repetition of equal values, the table lists the values as “ fx”

f18

f15

f:27,5

f13

fll

3 150

f23,5

rt16,5

2 500

1 +I8 1 k20

1 +12,5 1 +14

2500

f16

+11

+13,5

+12,5

&II,5

7,5

2000

IL 8

&IO

f9

,

+I0

+9

1 f

+32,5

5,5

,

Ifr7 +8

f6

1 * 5

+ 4,5 IL 5,5

1 k 6,5

,

+27,5

f

+7,5

i-6,5

3,5

IL 4

+3

31 2,5

+2

5

+23

4,5

+5

+4,5

,

f5 +6

+4

1 f3

+3 f

1 k 4

,

IL 2,5

k 2

IL 2

f1,5

4

+ 19,5

f

+4

,

+3,5 +4

+2,5

1 +2

+2

+2

1 f2,5

,

&I,5

+I,25

+I,25

kl

3

. JS2)

= es = ei

for shafts js

rounded in national standards by replacing the exact value by the integer immediately below, e.g. + 19,5 urn may be rounded to I!I 19 pm.

2)

500

400

f3,5

400

315

+I,25

+I,25

1 +I,5

,

+1

+0,75

+0,75

+0,6

2

1 f 6,5 1 k 9 630 1 800 11 31 5 f 5,5 1 f 7,5 1 &IO,5 8001’0001( 1 250 k12 1 000 + 6,5 +9 1250 1 600 + 7,5 &IO,5 f14,5 z!I 9 1600 2 000 +12,5 +17,5

1)

1 1

I

+1,75

180

+2,25 250 315 , rt3

120

180 250 ,

120 1 +I,25

80 I

.

I

kO,6

18

10

1

*0,5

10

50 . f0,75 80 1 fl

+0,5

6

30

+0,4

33)

1

3 6

and ineluding

up to

I

18

-

Above

mm

Basic size

30 , 50 1

I

Limit deviations’)

Upper limit deviation Lower limit deviation

Table 23 -

Is0 286-2 : 1988 (El

Table 24 -

Limit deviations

for shafts j and k

Upper limit deviation Lower limit deviation

= es = ei Deviations in micrometres

I

Basic size

i

mm

Above

up to and ineluding

-

3 6 10 18

k

I 51)

6’)

7’)

+2

+ 4 -2

+ 6 -4

6

+3 -2

+6 -2

':

1:

‘* 30

3

5

4

6

7

8

‘;

1;

+8 -6

+ 10 0

+ 14 0

+25

+ 13 +l

+18

+30

+2 0

+3

+4

+8 -4

+2,5 0

+5 +l

+6 +l

+ +l

+lO -5

+2,5 0

+5 +l

+7 +l

+ 10 +l

+16 +l

+22

+12

+3 0

+6 +I

+9 +l

+ 12 +l

+ 19 +I

+27

-6

0

+6 0

0 9

12

11

+40

13

+48

+36

60 0

+

100 0

+

140 0

+

75 0

+

120 0

+

180 0

+

90 0

+

150 0

+

220 0

0 +58

0

0 + 70 0

+

110 0

+

180 0

+

0

270 0

+84

+

130 0

+

210 0

+

330 0

250 0

+

390 0

+43 0

+ 0

0

0

+52

+5 -4

+9 -4

+13 -8

+4 0

+8 +2

+ll +2

+ 15 +2

+23 +2

+33 0

0

0

+4 0

+9 +2

+13 +2

+ 18 +2

+ 27 +2

+ 39 0

+ 62 0

+lOO 0

+

160 0

+

+ 74 0

+I20

+

190 0

+300

0

+140 0

+

220 0

+350

0

+ 87 0

50

+6 -5

+ll -5

+15 -10

50

80

+6 -7

+12 -7

+18 -12

+lO +2

+15 +2

+ 21 +2

+32 +2

+46

:;

+13

+13 +3

+18 +3

+25 +3

+38 +3

+54

-9

+20 -15

120

IO

0

0

30

80

9

I

3

I0

8

0

120

180

‘,:

+14 -11

+22 -18

+15 +3

+21 +3

+28 +3

+43 +3

+63

+lOO 0

+160 0

+250

0

180

250

‘,j

+16

+25 -21

+18 +4

+24 +4

+33 +4

+50 +4

+ 72 0

+115 0

+185 0

+290

-13

+460 0

0 +540

0 +400

0 +

630 0

+

720 0

0

0 +460

0

0

250

315

;,;

+16

f26

+20 +4

+27 +4

+36 +4

+56 +4

+ 81 0

+130 0

+210 0

+

320 0

+

520 0

+

810 0

315

400

1,;

+18

+29 -28

+22 +4

+29 +4

+40 +4

+61 +4

+89

+140 0

+230 0

+

360 0

+

570 0

+

0

890 0

+31 -32

+25 +5

+32 +5

+45 +5

+68 +5

+ 97 0

+155 0

+250 0

+400

+

970 0

+20

+630 0

0

.

.

500 500

+44 +44

630 630

+ 70 0

+llO

+175 0

+280 0

+440

0

+80

+200 0

+320 0

+500

0

+125 0

0

+230 0

+360 0

+560

0

+140 0 +165 0

+260 0

+420 0

+

0

+105 0

+ 78 0

+125 0

+195 0

+310 0

+500 0

+

+ 92

+150 0

+230 0

+370 0

+600 0

+

0

+280 0

+440 0

+700 0

+llOO

+330 0

+540 0

+860 0

+1350

0

630

+50

800

0

800 1000 1250 1600

I)

1000

+56

1250

+66

1600 2000

+90

2000

2500

+llO 0

+175 0

2500

3 150

+135 0

+210 0

Where values for j5, j6 and j7 are shown as ” +x”,

+ 0

700 0

+800

0 +1250

0

0 +900 0

0 +1400

0

660 0

+1050

780 0

+1250

920 0

+1500

0 +1650

0

0 +1950

0

0 +2300

0 +1750

0

0 +2800

0 +2100

0

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

0 +3300

0

they are identical with the tolerance class js5, js6 or js7 for that basic size step.

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

COPYRIGHT 2003; International Organization for Standardization

+lloO

0

ISO286=2:1988E)

Table 25 -

Limit deviations

for shafts m and n

Upper limit deviation Lower limit deviation

= es = ei Deviations in micrometres

Basic size

m

n

mm Above -

3

"

10 18 30 1

50 1

up to and ineluding

3

4

5

6

7

8

9

3

4

5

6

7

8

9

+ 14 + 4

+I8 +4

+29 +4

+20 + 8

+26 +8

+38 +8

*

3

+4 +2

+5 +2

+6 +2

+ +

8 2

+ 12 + 2

+I6 +2

+27 +2

+6 +4

+7 +4

+8 +4

+ 10 + 4

6

+ 6,5 +4

+ 8 +4

+ 9 d-4

+ 12 + 4

+ 16 + '4

+22 +4

+34 +4

+10,5 +8

+I2 +8

+I3 +8

+I6 + 8

lo

+ 8,5 +6'

+I0 +6

+I2 +6

+ 15 + 6

+ 21 + 6

+28 +6

+42 +6

+12,5 +I0

+I4 +I0

+I6 +I0

+ 19 + 10

+ 25 + 10

+32 +I0

+46 +I0

'*

+I0 +7

+I2 +7

+I5 +7

+ 18 + 7

+ 25 + 7

+34 +7

+50 +7

+I5 +I2

+I7 +I2

+20 +I2

+ 23 + 12

+30 + 12

+39 +I2

+55 +I2

3o

+I2 +8

+I4 +8

+I7 +8

+ 21 + 8'

+ 29 + 8

+41 +8

1:

+I9 +I5

+21 +I5

+24 +I5

+ 28 + 15

+36 + 15

+48 +I5

+67 +I5

+I3 +9

+I6

+20

+ 25

+34

+48

+71

+21

+24

+28

+33

+ 42

+56

+79

5o

1 +I7

/ +I7

80 1

1 ;;;

1 ;;

1 f;

1 ;;

1 +'

1 +'

( +I7

/ ;;;

1 ;;

/ ;;

I

/ ;;

80

120

+23 +I3

+28 +I3

+ 35 + 13

+48 + 13

+33 +23

+38 +23

+ 45 + 23

+58 + 23

120

180

+27 +I5

+33 +I5

+40 + 15

+ 55 + 15

+39 +27

+45 +27

+ 52 + 27

+ 67 + 27

180

250

+31 +I7

+37 +I7

+ 46 + 17

+63 + 17

+45 +31

+51 +31

+60 + 31

4-77 + 31

250

315

+36 +20

+43 +20

+ 52 + 20

+ 72 + 20

+50 +34

+57 +34

+66 +34

+ 86 +34

315

400

+39 +21

+46 +21

+ 57 + 21

+ 78 + 21

+55 +37

+62 +37

+ 73 + 37

+94 + 37

I 23I 1;:I 1: I I ii I I I

400

500

500

630

+ 70 + 26

+ 96 + 26

+88 +44

+I14 +44

630

800

+ 80 + 30

+I10 + 30

+I00 +50

+I30 +50

800

1 000

+ 90 +34

+I24 +34

+I12 +56

+I46 +56

1 000

1 250

+I06 +40

+I45 +40

+I32 +66

+I71 +66

1 250

1 600

+I26 +48

+I73 +48

+I56 + 78

+203 + 78

1 600

2000

+I50 +58

+208 +58

+I84 + 92

+242 + 92

2 000

2 500

+I78 +68

+243 +68

+220 +I10

+285 +I10

2 500

3 150

+211 + 76

+286 + 76

+270 +I35

+345 +I35

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

I

I

COPYRIGHT 2003; International Organization for Standardization

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

31

Iso

286-2 : 1988 (E)

Table 26 -

Limit deviations

Upper limit deviation Lower limit deviation

for shafts p = es = ei

Basic size

Above I

P

I

r-rm up to and ineluding

3

4

5

6

7

8

9

IO

3

+8 +6

+9 +6

+I0 +6

+ 12 +6

+I6 +6

+20 +6

+31 +6

+46 +6

3

6

+14,5 +I2

+I6 +I2

+I7 +I2

+ 20 + 12

+24 + 12

+30 + 12

+42 +I2

+60 + 12

6

10

+17,5 +I5

+I9 +I5

+21 +I5

+ 24 + 15

+ 30 + 15

+ 37 + 15

+51 +I5

+ 73 + 15

10

18

+21 +I8

+23 +I8

+26 +I8

+29 + 18

+ 36 + 18

+ 45 + 18

+61 +I8

+88 + 18

+26 +22

+28 +22

+31 +22

+35 +22

+43 +22

+ 55 +22

+74 +22

+I06 +22

+30 +26

+33 +26

+37 +26

+ 42 + 26

+ 51 + 26

+65 + 26

+88 +26

+I26 + 26

18

3o

30

50

50

80

+40 +32

+45 +32

+ 51 + 32

+ 62 + 32

+ 78 + 32

80

120

+47 +37

+52 d-37

+59 + 37

+ 72 + 37

+ 91 + 37

120

180

+55 +43

+61 +43

+68 +43

+83 +43

+I06 +43

180

250

+64 +50

+70 +50

+79 +50

+96 +50

+I22 +50

250

315

+72 +56

+79 +56

+88 +56

+I08 +56

+I37 +56

315

400

+80 +62

+87 +62

+98 + 62

+I19 + 62

+I51 + 62

400

500

+88

+95 +68

+I08 +68

+I31 +68

+I65 +68

500

630

+I22 + 78

+I48 + 78

' +I88 + 78

630

800

+I38 +88

+I68 +88

+213 +88

+68

800

1000

+I56 +I00

+I90 +I00

+240 +I00

1000

1 250

+I86 +I20

+225 +I20

+285 +I20

1 250

1600

+218 +I40

+265 +I40

+335 +I40

1600

2000

+262 +I70

+320 +I70

+400 +I70

2000

2500

+305 +I95

+370 +I95

+475 + 195

2500

3150

+375 +240

+450 +240

+570 +240

COPYRIGHT 2003; International Organization for Standardization

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

Deviations in micrometres

IS0 286-2 : 1988 0

Table 27 -

Limit deviations

for shafts r

Upper limit deviation Lower limit deviation

= es = ei Deviations in micrometres

b

Basic size

r

mm I I

I

I

UI

Above

anta$l clu-...,

3

q

+I2 +10 +17,5 +I5

-

5

6

+ 13 + 10

+ 14 + 10

+ 16 + 10

I 1 +21,5 +I9

+ 19 + 15

+ 20 + 15

+ 23 + 19

+26 +23

In =I=

/

4

1

7

8

9

IO

+ 20 -+ 10

+ 24 + 10

+35 + 10

+50 + 10

500

560

+I94 +I50

+220 +I50

+260 +I50

+23 + 15

+ 27 + 15

+33 + 15

+45 +I5

+63 + 15

560

630

+I99 +I55

+225 +I55

+265 +I55

+ 25 + 19

+ 28 + 19

+34 + 19

+ 41 + 19

i-55 +I9

-l-77 + 19

630

710

+225 +I75

+255 +I75

+300 +I75

+ 28 + 23

+ 31 + 23

+34 + 23

+ 41 + 23

+50 + 23

+66 +23

+ 93 + 23

710

800

+235 +I85

+265 +I85

+310 +I85

IU

30

+32 +28

+34 + 28

+ 37 + 28

+ 41 + 28

+49 + 28

+ 61 + 28

+80 +28

+I12 + 28

3n au

50

+38 +34

+ 41 +34

+ 45 +34

+50 +34

+59 +34

+73 +34

+96 +34

+I34 +34

50

65

CK VLI

80

f2n

100

vu

Inn IVU

'qn ILU

120 /

140

1

+49

+54

+60

+ 41

+ 41

+ 41

+ 71 + 41

+ 87 + 41

+ 51 +43

+56 +43

+ 62 4-43

+ 73 +43

+89 +43

1 120

1250

+326 +260

+365 +260

+425 +260

+ 61 + 51

+66 + 51

+ 73 + 51

+86 + 51

+I05 + 51

1250

1400

+378

+425

+300

+ 495 +300

+64

+69

+89 +54

+I08 +54

1600

1;

+54

+ 76 +54

1400

+54

+455 +330

+525 +330

1600

1800

+462 +370

+520 +370

+600 +370

2000

+ 492 +400

+550 +400

+630 +400 +720

1 ; E

1 1;

1 1:

/

;'i

/ 1': --

140

icn IUU

160

180

IQn IUU

I

3nn &WV

I

1 --

1

+77

+83

+90

+ 65

+ 65

+I05 + 65

+I28 + 65

1800

+ 65 + 80 +68

+ 86 +68

+ 93 +68

+I08 +68

+I31 +68

2000

1 + 91

1 + 97

1 +I06 + 77

1 +I23 -I-n

-l-77

+77



I

I

+I49 +77

I

I

2 240

+I26 +80

+I52 +80

2500

250

+I30 +84

+I56 +84

2800

wzn

280

+I46 +94

+I75 +94

qon

315

+I50 +98

+I79 + 98

onn LUV

225

33E LLLJ

LWU

LOU

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

cI)IC

+I00 +80

+I09 + 80

+550

+615

2240

+440

+440

+440

2500

+570

+635

+74O

+460

+460

+460

;g

+760 +550

+880 +550

+715

+790

+910

+580

+580

+580

2800

3150

355

QKK

AM ‘NW

+I32 +I14

+I39 +I14

+I50 +I14

+I71 +I14

+203 +I14

400

450

+I46 +I26

+I53 +I26

+I66 +I26

+I89 +I26

+223 +I26

3JJ

+300

nm

500 I

I

,

+I52 +I32

COPYRIGHT 2003; International Organization for Standardization

,

+I59 +I32

,

+I72 +I32

,

+I95 +I32

,

+229 +I32

,

I

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

ISO286-2:1988(E)

Table 28 -

Limit deviations

for shafts s

Upper limit deviation Lower limit deviation

= es = ei Deviations in micrometres Basic size

S

mm Above

up to and ineluding 3

-

3

up to and ineluding

4

5

6

7

8

9

IO

+I6 +I4

+ 17 + 14

+ 18 + 14

+ 20 + 14

+ 24 + 14

+28 + 14

+39 + 14

+54 + 14

500

560

+ +

Above

6 324 280

7

8

+350 +280

+390 +280

3

6

+21,5 +I9

+ 23 + 19

+ 24 + 19

+ 27 + 19

+ 31 + 19

-I-37 + 19

+49 + 19

+ 67 + 19

560

630

1 zl

:

z

+ +

420 310

6

10

+25,5 +23

+27 + 23

-129 + 23

+32 +23

+38 +23

+45 + 23

+59 + 23

+ 81 + 23

630

710

:lt

+

420

+

465

18

+31 +28

+33 +28

+36 +28

+39 +28

+46 +28

+55 +28

+71 +28

+98 + 28

710

800

+44 + 35

+48 + 35

+56 + 35

+68 + 35

+ 87 + 35

+I19 + 35

900

:z

+4l + 35

800

3o

30

50

+47 +43

+50 +43

+54 -l-43

+59 +43

+68 +43

+82 +43

+I05 +43

+I43 4-43

900

50

65

+61 +53

+66 +53

+72 +53

+83 +53

+99 +53

+I27 +53

65

80

+ 67 +59

+ 72 +59

-1-78 +59

+89 +59

+I05 +59

80

100

+81 + 71

+86 + 71

+ 93 + 71

+I06 + 71

10 18

+340

+340

+430 + 380

+460 + 380

+505 + 380

1 g

+ +

520 430

+ +

570 430

looo

+ +

526 470

+ +

560 470

+ +

610 470

1000

1 120

+ +

586 520

+ +

625 520

+ +

685 520

+I33 +59

1 120

1250

1 E

+

745

+I25 + 71

+I58 + 71

1 250

1400

+

+

835

718

1 E +

765

+ 580

+640

+640

+640

+798 + 720

+845 + 720

+ +

+ 912

+ 970

+

+

820

+I050 + 820

+89

+94

+I14 + 79

+I33 + 79

+I66 + 79

1 600

+ 79

+I01 + 79

1400

+ 79

140

+I04 + 92

+I10 + 92

+I17 + 92

+I32 + 92

+I55 + 92

+I92 + 92

1600

1 800

140

160

+I12 +I00

+I18 +I00

+I25 +I00

+I40 +I00

+I63 +I00

+200 +I00

1800

2000

+I012 + 920

+I 070 + 920

+I150 + 920

460

180

+I20 +I08

+I26 +I08

+I33 +I08

+I48 +I08

+I71 +I08

+208 +I08

2000

2240

+1110 +I000

+I175 +I ooo

+I 280 +I000

WI

200

+I36 +I22

+I42 +I22

+I51 +I22

+I68 +I22

+I94 +I22

+237 +I22

200

225

+I44 +I30

+I50 +I30

+I59 +I30

+I76 +I30

+202 +I30

+245 +I30

225

250

+I54 +I40

+I60 +I40

+I69 +I40

+I86 +I40

+212 +I40

+255 +I40

250

280

+I74 +I58

+I81 +I58

+I90 +I58

+210 +I58

+239 +I58

+288 +I58

280

315

+I86 +I70

+I93 +I70

+202 +I70

+222 +I70

+251 +I70

+300 +I70

315

355

+208 +I90

+215 +I90

+226 +I90

+247 +I90

+279 +I90

+330 +I90

355

400

+226 +208

+233 +208

+244 +208

+265 +208

+297 +208

+348 +208

400

450

+252 +232

+259 +232

+272 +232

+295 +232

+329 +232

-I387 +232

450

500

+272 +252

+ 279 +252

+292 +252

+315 +252

+349 +252

+4Q7 +252

100

120

120

34 COPYRIGHT 2003; International Organization for Standardization

820

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

915 720

IS0 286-2 : 1988 (El

Table 29 -

Limit deviations

for shafts t and u

Upper limit deviation Lower limit deviation

= es = ei Deviations in micrometres

Basic size

Basic size

t’)

mm up to and ineluding

5

6

7

8

5

6

7

8

9

- 1 3 ) / 1 / I:ei:~l::lxlz3 3

6

6

10

10

18

18

24

24 30

5001

+ 31 + 23

+ 35 + 23

+41 + 23

+53 + 23

560

+34 +28

+37 +28

+43 +28

+50 +28

+64 + 28

630

+41 +33

+44 +33

+51 +33

+60 +33

+ 76 +33

+50

+54

+ 41

+ 41

+ 62 + 41

+ 74 + 41

+ 93 + 41

;;

1':

+99

11:

14":

1;

;;;

1;

1;

;;

1:

40

;z

1;

1;

;z

1;

;z

=z

up to and ineluding

Above

+ 28 + 23

30

I

7

6

7

8

yz;

1; El; 2

630

/ 1; E1=z 710

+60

40

50

+ 54 65

;

;I:

1 g

1 ;

1 ;;

1 ;;

;

50

65

3-7966 +

+8566 +

1 z

1';

;';

1';

1';

;;

1':

1';;

1';

1';;

f 400

1 600

+I 128 +I050

+I175 +I050

+I678 +I600

+I725 +I600

+I795 +I600

1 600

1800

+I292 +I200

+I350 +I200

+I942 +I850

+2000 +I850

+I850

+I442 +I350

+I500 +I350

+2092 +2000

+2150 +2000

+2230 +2000

1 800

2 000

2 000

2240 I

I I

2240 180

+I64 +I46

+I71 +I46

+I86 +I46

+209 +I46

+228 +210

+235 +210

+250 +210

+273 +210

+310 +210

180

200

+I86 +I66

+I95 +I66

+212 +I66

+238 +I66

+256 +236

+265 +236

+282 +236

+308 +236

+351 +236

200

225

+200 +I80

+209 +I80

+226 +I80

+252 +I80

+278 +258

+287 +258

+304 +258

+330 +258

+373 +258

225

250

+216 +I96

+225 +I96

t242 +I96

+268 +I96

+304 +284

+313 +284

+330 +284

+356 +284

+399 +284

250

280

+241 +218

+250 +218

+270 +218

+299 +218

+338 +315

+347 +315

+367 +315

+396 +315

+445 +315

280

315

+263 +240

+272 +240

+ 292 +240

+321 +240

+373 +350

+382 +350

+402 +350

+431 +350

+480 +350

315

355

+293 +268

+304 +268

+325 +268

+357 +268

+415 +390

+426 +390

+447 +390

+ 479 +390

+530 +390

355

400

+319 +294

+330 +294

+351 +294

+383 +294

+460 +435

+471 +435

+492 +435

+524 +435

+575 +435

400

450

+357 +330

17;

;g

1%

;g

;y;

;z

;F;

;g

450

500

d-387 +360

+400 +360

+423 +360

+457 +360

+567 +540

+580 +540

+603 +540

+637 +540

+695 +540

160

I

6

5601;

1

t

2 500 2800

+I610 +I675 +2410 +2475 1+15001+15001+2300~+2300~+2300 I I I 1 I

I

I

I

+2080

+2580 I I

2500

+I760 +I650

+I825 +I650

+2610 +2500

+2675 +2500

+2780

2 800

+2035 +I900

+2110 +I900

+3035 +2900

+3"0 +2900

+3230

3150

+2235 +2100

+2310 +2100

+3335 +3200

+3410 +3200

+3530 +3200

+2500 +2900

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

Above

U

mm

1) Tolerance classes t5 to t8 (incl.) have not been tabulated for basic sizes less than or equal to 24 mm. It is recommended that tolerance classes u5 to u8 (incl.) be used instead. However, if tolerance classes t5 to t8 (incl.) are especially required, they may be calculated from the bases given in IS0 286-l.

35 COPYRIGHT 2003; International Organization for Standardization

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

IS0 286-2 : 1988 E)

Table 30 - Limit deviations

for shafts v, x and yl)

Upper limit deviation Lower limit deviation

= es = ei Deviations in micrometres

Basic size

Y3'

X

V2)

mm Above

up to and ineluding

5

6

7

8

3

-

3

6

5

6

7

8

9

+ 24 + 20

+ 26 + 20

+30 + 20

+34 + 20

+45 + 20

+ +

60 20

+33

+36 + 28

+40 + 28

+46 + 28

+58 + 28

+ +

76 28

+28

6 10

10 14

6

IO

+40

+43

+49

+56

+34

+34

+34

+34

+ 70 +34

+ +

92 34

+48 +40

+51 +40

+58 +40

+67 +40

+83 +40

+ +

110 40 115 45

14

+47

+50

+57

+66

+53

+56

I8

+39

+39

+39

+39

+45

+45

+63 + 45

+72 + 45

+88 + 45

+ +

18 24

24 3o

1: zz

1: iz

2

z

1:

+54 + 67

+ +5475

++5487

+I06 +54

1’:

+76 + 55

+88 +55

d-73 +64

-l-77 +64

+85 +64

+ 97 +64

+I16 +64

+ +

148 64

+ +

30

+79

+ 93 +68

+91

+96

+I05

+I19

+68 + 92

+84 +68 + 97

+I07

4o 50

+68

+80

+80

+80

+80

+I42 +80

+ +

180 80

+ 81

+ 81

+I06 + 81

+I20 + 81

+I08 + 97

+I13 + 97

+I22 + 97

+I36 + 97

+I59 +97

+ +

+I15 +I02 +I33 +I20 +I61 +I46

+I21 +I02

+I32 +I02

+148

+I02

+I35 +I22

+I41 +I22

+I52 +I22

+I68 +I22

+I96 +I22

+I39 +I20

+I50 +I20

+I66 +I20

+I59 +I46

+I65 +I46

+I76 +I46

+I92 +I46

+I68 +I46

+I81 +I46

+200 +I46

+I93 -1-178

+200 +I78

+213 +I78

+I87 +I72

+I94 +I72

+207 +I72

+226 +I72

+225 +210

+232 +210

+220

+227 +202

+242 +202

+265 +202

+266 +248

+253 +228 +277 +252 +313 +284 +339 +310 +369 +340 +417 +385

+268 -1-228 + 292 +252 +330 +284 +356 +310

+291 +228 +315 +252

+298 +280 +328 +310

+356 +284

+370 +350

+382 +310

+386 +340 d-437 +385

40 50

65

7

8

+I15

+I47

Ei

1

ii

+63

+63

88 75

+ +

96 75

+ +

108 75

+I27 + 75

+I59 + 75

+ +

110 94

+ +

119 94

+ +

133 94

+I56 +94

+I94 +94

197 97

+ +

130 114

+ +

139 114

+ +

153 114

+I76 +I14

+214 +I14

+ +

242 122

+ +

163 144

+ +

174 144

+ +

190 144

+220 +I46

+ +

266 146

+ +

193 174

+ 204 -I- 174

+ +

220 174

+232 +I78

+265 +I78

+ +

318 178

+ +

236 214

+ +

249 214

+ +

268 214

+245 +210

+264 +210

+ 297 +210

+ +

350 210

+ +

276 254

+ +

289 254

+ +

308 254

+273 +248

+288 +248

+311 +248

+348 +248

+ +

408 248

+325 + 300

+340 + 300

+ +

363 300

+305 +280

+320 +280

+343 +280

+380 +280

+ 440 +280

+ 365 +340

+ 380 +340

+ 403 +340

+335 +310

+350 +310

+373 +310

+410 +310

+ +

+ +

405 380

+ +

420 380

+ +

443 380

+396 +350

+422 +350

+465 +350

+535 + 350

+454 + 425

+ +

471 425

+ +

497 425

+405 +385

+ 379 +350 +414 +385

+431 +385

+457 +385

+500 +385

+ +

570 385

+ +

499 470

+ +

516 470

+ +

542 470

+412 +340

+445 +425

+454 +425

+471 +425

+497 +425

+540 +425

+ +

610 425

+ +

549 520

+ +

566 520

+ +

592 520

+466 +385

+498 +475

+507 +475

+527 +475

+556 +475

+605 +475

+ 685 -I- 475

+ +

612 580

+ +

632 580

+ +

661 580

+477 +425 +532 +475

+506 +425 +564 d-475

+548 +525 +615 +590

+557 +525 +626 +590

+577 +525

+655 +525

+ +

735 525

+ +

682 650

+ 702 +650

+ 731 +650

+647 +590

4-606 +525 + 679 +590

+730 +590

+ +

820 590

+ +

766 730

-I- 787 + 730

+ +

80

80

100

100

120

120

140

140

160

160

180

180

200

200

225

225

250

250

280

:zz

280

315

~~

315

355

+500 +475

+457 +425 +511 +475

355

400

+555 +530

+566 +530

+587 +530

+619 +530

+685 +660

+696 +660

+717 +660

+749 +660

+800 +660

+ +

890 660

+ +

856 820

+877 + 820

+909 + 820

400

450

+622 +595

+635 + 595

+658 +595

+692 +595

+767 +740

+780 +740

+803 +740

-a337 +740

+895 +740

+ +

990 740

+ +

960 920

+ +

+I 017 + 920

450

500

+687 +660

+700 +660

+723 +660

+757 +660

+847 +820

+860 +820

+883 +820

+917 +820

+ 975 +820

+I 070 + 820

1)

+360

+#j40

IO

:

12

65

+202 +246 +228 +270 +252 +304 +284 +330 +310

9

470 310

+I040 +I ooo

983 920

+I 063 +I ooo

819 730

+I097 +1000

A

Fundamental deviations v, x and y are not provided for basic sizes greater than 500 mm.

2) Tolerance classes v5 to v8 (incl.) have not been tabulated for basic sizes less than or equal to 14 mm. It is recommended that tolerance classes x5 to x8 (incl.) be used instead. However, if tolerance classes v5 to v8 (incl.) are especially required, they may be calculated from the bases given in IS0 286-l. 3) Tolerance classes y6 to ~10 (incl.) have not been tabulated for basic sizes less than or equal to 18 mm. It is recommended that tolerance classes 26 to ~10 (incl.) be used instead. However, if tolerance classes y6 to ~10 (incl.) are especially required, they may be calculated from the bases given in IS0 286-l.

36 --`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

COPYRIGHT 2003; International Organization for Standardization

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

IS0 286-2 : 1988 (El

Table 31 - Limit deviations

for shafts z and zal)

Upper limit deviation Lower limit deviation

= es = ei Deviations in micrometres

Basic size

za

Z

mm 6

7

8

9

6

11

IO

7

9

IO

11

+ +

38 32

+ +

+a +

42

+54 + 42

+60 + 42

+72 + 42

+%I + 42

-I- 117 + 42

+ +

61 52

+ +

+ +

+ +

+ +

+ +

42 32

67 52

+ +

46 32

74 52

+ +

57 32

88 52

+ +

72 32

110 52

+ +

92 32

142 52

+ 75 +64

+ 82 +64

+ 91 +64

+ 107 +64

+ 134 +64

+ 174 +64

+ 88 4-77

+ 95 4-n

+ 104 +77

+ 120 4-77

+ 147 4-77

+ 187 +77

18

+ +

111 98

+ +

119 98

+ +

131 98

+ +

150 98

+I82 + 98

+228 + 98

24

+ +

131 118

+ +

139 118

+ +

151 118

+ +

170 118

+ +

202 118

-I- 248 + 118

+ +

164 148

+ +

173 148

+ +

187 148

+ +

210 148

+248 + 148

+308 + 148

242 180

+280 + 180

+340 + 180

14

-120

'*

/

140

1:

1:

1 1 ;!

140

160 s5

160

180

+ 490 +

465

::

+ 103 +60

+ 130 +60

/

+ 170 +60

+ +

296 136

+ +

196 180

+ +

205 180

+ +

219 180

+ +

+ +

362 172

+ +

245 226

+ +

256 226

+ +

272 226

+300 +226

+346 +226

+ +

+400 + 210

+ +

293 274

+ +

304 274

+320 + 274

+348 + 274

+394 + 274

+464 + 274

-I- 478 + 258

+ +

357 335

+ +

370 335

+ +

+ +

+ +

+ +

530 310

+ 422 +400

+ 435 +400

+ 454 +400

+4a7 +400

+54-o +400

+ 620 +400

+ +

615 365

+ +

+510 + 470

+533 + 470

+ +

570 470

+ +

630 470

+ +

720 470

+ +

+ +

635 535

+ +

695 535

+ +

785 535

495 470

250

280

-I- 742 + 710

280 315 355

355 400

400

450

575 535

389 335

.+ +

422 335

475 335

416 226

555 335

+ +

455 415

+ +

478 415

+ +

515 415

+ +

575 415

+ +

665 415

+560 + 535

+ +

+ +

505 465

+ +

528 465

+ +

565 465

+ +

625 465

+ +

715 465

+ 625 +600

+ 640 +600

+ 663 +600

+ 700 +600

+760 +600

+850 +600

+699 + 670

+ +

716 670

+ +

742 670

+ +

785 670

+ +

855 670

+ +

+ +

786 740

+ +

812 740

+ +

855 740

+ +

925 740

+I 030 -I- 740

598 535

960 670

+ +

621 575

+647 + 575

+690 + 575

+ +

760 575

+ +

865 575

+ +

+

686

+

712

-I- 755

+

825

+

930

+849 + 820

+866 + 820

+ +

892 820

+ 935 +820

+I005 +820

+1110 + 820

+ +

762 710

+791 + 710

+840 + 710

+ +

920 710

+I 030 + 710

+ +

+ +

972 920

+I001 + 920

+I 050 + 920

+I130 + 920

+I240 + 920

+ +

842 790

+ +

+ +

+I000 + 790

+I 110 + 790

+I 032 +'ooo

+I 052 +I000

+I081 +I ooo

+I 130 +I ooo

+I210 +I000

+I 320 +I000

769 740

*5 250:z +640 +640 +640 +640 +640

1)

8

871 790

920 790

952 920

+ 936 +m

+ 957 +900

+ 989 +900

+I 040

+I130

+I260

+900

+900

+900

+I186 +I 150

+I207 +I150

+I239 +I 150

+I 290 +I150

+I380 +I150

+I 510 +I150

+I036 +I ooo

+I057 +I ooo

+I 089 +I ooo

+I140 +I000

+I230 +I ooo

+I360 +I000

+I 336 +I 300

+I 357 +I300

+I 389 +I300

+I 440 +I300

+I 530 +I300

+I 660 +I300

+I140 +I loo

+I163 +I loo

+I 197 +I100

+I 255 +I100

+I350 +I100

+I 500 +I loo

+I 490 +I 450

+I513 +I450

+I547 +I450

+I605 +I 450

+I700 +I 450

+I850 +I450

+I 640 +I 600

+I 663 +I 600

+I697 +I 600

+I755 +I600

+I 850 +I 600

+2000 +I 600

Fundamental deviations z and za are not provided for basic sizes greater than 500 mm.

37 COPYRIGHT 2003; International Organization for Standardization

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

up to and ineluding

Above

IsO286=2:1988E)

Table 32 - Limit deviations

for shafts zb and zcl)

Upper limit deviation Lower limit deviation

= es = ei Deviations in micrometres

Basic size

zb

zc

mm up to and including

- -I 3

3 6

7

8

IO

11

7

8

9

IO

11

+

50

+

54

+

+

40

+

40

+

65 40

+ +

80 40

+ +

loo 40

+ +

70 60

+ +

74 60

+ +

85 60

+ +

loo 60

+ +

120 60

+ +

62 50

+ +

68 50

+ +

80 50

+ +

98 50

+ +

125 50

+ +

92 80

+ +

98 80

+ +

110 80

+ +

128 80

+ +

155 80

+ +

82 67

+ +

89 67

+ +

103 67

+ +

125 67

+ +

157 67

+ +

112 97

+ +

119 97

+ +

133 97

+ +

155 97

+ +

187 97

+ +

108 90

+ +

117 90

+ +

133 90

+ +

160 90

+ +

200 90

+ +

Ma 130

+ +

157 130

+ +

173 130

+200 + 130

+ +

240 130

+260 + 150

14

18

+ +

126 108

+ +

135 108

+ +

151 108

+ +

178 108

+ +

218 108

+ +

168 150

+ +

177 150

+ +

193 150

+ +

18

24

+ +

157 136

+ +

169 136

+ +

188 136

+ +

220 136

+ +

266 136

+209 + 188

+ +

221 188

+ +

240 188

-I- 272 + 188

+ +

24

30

+ +

181 160

+ +

193 160

+ +

212 160

+ +

244 160

+290 + 160

+239 + 218

+ +

251 218

+ +

270 218

+ +

302 218

+348 + 218

30

40

+ 225 +200

+239 +200

+ +

262 200

+300 + 200

+360 +200

+ +

+ +

313 274

+ 336 -I- 274

+ +

374 274

+434 + 274

40

50

+ +

+ +

+304 + 242

+ +

342 242

+ +

50

65

I=

+

+

420

XE

65 *O loo

*O

267 242

281 242

:z

IE

xz

loo

:E

+,E

120

;g

+ 579 +

1)

9

525

374

+300

+300

:z

zi

318 188

+350 + 325

+364 + 325

+ +

387 325

+ +

425 325

+485 + 325

+

+405

+ +

+ +

479 405

+ 525 +405

+ 595 +405

+360

+ +

510 480

+ 526 +480

+554 + 480

+600 +480

+ 670 +480

+ 665 +445

+ +

620 585

+639 + 585

+ +

672 585

+ 725 +585

+805 +585

+

402 242

299 274

220 150

550

I

435

451 405

+ 532 +445

SE

+ +

612 525

+ +

665 525

+ +

745 525

+ 725 +690

-I- 744 +690

+ 777 +690

+ 830 +690

+ 910 +690

120

140

;

z

1 z

+ +

720 620

-I- 780 + 620

+ +

870 620

+840 +800

+863 +800

+900 +800

+960 +800

+I 050 +800

140

160

+ +

740 700

+ +

+800 + 700

+860 + 700

+ +

950 700

+940 +900

+963 +900

+I ooo +900

+I 060 +900

+I150 +9CNl

160

180

ZE

1%

:z

+I 030 -I- 780

+I 040 +I ooo

+I063 +I ooo

+I loo +I ooo

+I160 +I000

+I250 +I000

lBO

200

+ +

+I065 +880

+I170 +880

+I 196 +I150

+I 222 +I 150

+I 265 +I150

+I335 +I150

+I 440 +I150

200

225

+I 006 +960

+I032 +960

+I 075 +960

+I 145 +960

+I250 +960

+I296 +I250

+I322 +I250

+I 365 +I250

+I435 +I250

+I540 +I250

225

250

+I096 +I050

+I122 +I 050

+I165 +I 050

+I235 +I050

+I340 +I 050

+I 396 +I350

+I422 +I 350

+I465 +I350

+I535 +I350

+I640 +I350

250

280

+I 252 +I200

+I 281 +I200

+I330 +I200

+I410 +I 200

+I520 +I200

+I 602 +I550

+I631 +I550

+I680 +I550

+I760 +I 550

+I 870 +I550

280

315

+I352 +I300

+I381 +I300

+I430 +I300

+I510 +I 300

+I620 +I300

+I 752 +I700

+I781 +I700

+I830 +I700

+I 910 +I700

+2020 +I700

315

355

+I 557 +I500

+I589 +I500

+I640 +I500

+I730 +I500

+I860 +I 500

+I 957 +I900

+I989 +I900

+204-O +I900

+2130 +I900

+2260 +I 900

355

400

+I 707 +I650

+I739 +I650

+I790 +I650

+I880 +I650

+2010 +I650

+2157 +2100

+2189 +2100

+2240 +2100

+2330 +2100

+2460 +2100

400

450

+I 913 +I850

+I947 +I850

+2005 +I850

+2100 +I 850

+2250 +I850

+2463 +2400

-12497 +24m

+2555 +2400

+2650 +24OO

+28OO +2400

450

500

+2163 +2100

+2197 +2100

+2255 +21aO

+2350 +2100

+2500 +2100

+2663 +2600

+2697 +26OO

+2755 +2600

+2850 +26OO

+3000 +2600

763 700

:z 926 880

+ +

952 880

+ +

995 880

Fundamental deviations zb and zc are not provided for basic sizes greater than 500 mm.

38 COPYRIGHT 2003; International Organization for Standardization

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

Above

IS0 286-2 : 1988 (El

Annex Graphical

review

of tolerance

zones

(This annex does not form an integral

A.1

Representation

of tolerance

zones

of holes and shafts

part of the standard.)

for holes

A graphical review of a broad selection of tolerance classes for holes is given in figures 6 and 7. Figure 6 shows the tolerance classes in terms of the fundamental deviation (A to ZC), whereas figure 7 gives the same information in terms of the standard tolerance grade (IT5 to IT1 1). Figures 6 and 7 do not include all the tolerance classes given in this part of IS0 286 and reference should be made to the tables for specific details. For comparative purposes, the tolerance classes given in figures 6 and 7 illustrate the values for ES, EIand IT given for the basic size step from 6 to 10 mm. Where there are no tabulated values for this basic size step, i.e. those tolerance classes involving fundamental deviations T, V and Y, the values have been given, again for comparative purposes, for the basic size step from 24 to 30 mm.

A.2

Representation

of tolerance

zones

for shafts

A graphical review of a broad selection of tolerance classes for shafts is given in figures 8 and 9. Figure 8 shows the tolerance classes in terms of the fundamental deviation (a to zc), whereas figure 9 gives the same information in terms of the standard tolerance grade (IT5 to IT1 1). Figures 8 and 9 do not include all the tolerance classes given in this part of IS0 286 and reference should be made to the tables for specific details. For comparative purposes, the tolerance classes given in figures 8 and 9 illustrate the values for es, ei and IT given for the basic size step from 6 to 10 mm. Where there are no tabulated values for this basic size step, i.e. those tolerance classes involving fundamental deviations t, v and y, the values have been given, again for comparative purposes, for the basic size step from 24 to 30 mm.

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

COPYRIGHT 2003; International Organization for Standardization

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

Iso286-2:

1988 E)

II 10

I

C

B

A 9

13 12

9 8

n 10

13 12

11

9 8

'0

CD 12

I3

7 6

D

9 8

6 IO

9

7 I

IIIIIIIIIIIIIIIIIIIII

I

I

E

IO

8 I

12 11

I

I

I

5

7

13 I

I

6

F

EF

91 51 171 I91 8 IO 6 8 IO

FG

6

8

G

IO

6

8

IO

6

8

J

H

51 171 191 51 171 I91

51 I71 I91

IO

51 I71 I91 1111 I13 I7 6

8

10

I

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

+400

(concluded)

J 171 6

JS

KM

N

P

R

STUVXY

Z

ZA ZB ZC '

51 171 191 1'11 1'3 161 18 161 18 161 181 1'01 51 171 19 161 18, 161 10, 171 ,61 18, 171 ,61 IS, 171 ,61 181 Ilo, 171 191 ,71 191 ,71 19r 8 o lo '0 '2 151 171 151 171 151 171 191 11'1 161 181 151 171 151 171 161 181 171 161 181 171 161 181 171 191 161 181 1101 18 8 6 8

1111111111111 I I I I

I I I I I I

III

lIIll[II

IIIIIIIIllII

~~llllrllllllllll I I I I

I I I

I I I I I I tHtd

m--

Figure 6 - Graphical

review

of tolerance

classes for holes in terms of fundamental

deviations

40 COPYRIGHT 2003; International Organization for Standardization

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

IS0 286-2 : 1988 (I3

I

IT5 Pm +200

E

I

IT6

IT7

1 IT8

S U X 21 :D E F IG J K N R T V Y ZAl ZC C ID /G JS M P S 10 EF FG H JS M P U X Z ZB B CD E K N R T V Y ZA D EF FG H JS M P S EF FG H K N R CD E F G J F

+lOO*

0a

-100 . i (concluded )

+300

+ 200

+ 100

0

-100

Figure 7 -

Graphical

review

of tolerance

classes for holes in terms of standard

tolerance

grades

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

COPYRIGHT 2003; International Organization for Standardization

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

41

Iso286-2:1988

(E)

I a I b I clcdl 9

I e I ef I f

d

I fa I cl I I

A

a

I i Iisl

IdI

I

a

I

a

I

'1 I3 9 11 13 9 11 6 8 10 6 8 IO 12 5 7 9 5 7 9 5 7 91 151 171-191 151 171 151 171 191 11111131 161 151 171 10 12 8 '0 12 8 IO 12 7 9 5 7 9 11 I3 6 8 10 6 8 IO 6 8 10 6 8 IO 6 81 161 181 1101 1121151 171 161 1 III

I

I

I

I

I

I

I

I

Zero line

- 500 (concluded ) . JS

Pm

8

k

m

n

p

10 12 5 7 9 11 5 7 5 7 5 7 9 11 13 6 8 10 12 6 8 68686860

r 5

7

s 5

7

u

t 5

6

7

8

5

6

7

v

957579 8 IO 6

x 8

6

8

y IO

6

7

llllllllllllllllllllllilllllllllllllllllllllllllllIllIIIIIIlII

z 8

6

7

za 9

8 -

10 .

I

6

8

7 I

I

zb IO

9 I

I

7

I

+ 100

Zero line

0

- 100 Figure 8 -

Graphical

review

of tolerance

classes for shafts in terms of fundamental

deviations

42 --`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

COPYRIGHT 2003; International Organization for Standardization

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

8 I

zc 10

9 I

I

-I

8

7 .I

9 -I

'0

IS0 286-2 : 1988 E)

IT5 e

f-g

j-

k

IT6 n’

r

t

v

cd e

f

g

j

k

n

IT7 r

cd t

v

y

za

e d

f ef

fg

g

j h

k js

n m

r p

s

t

u

v

x

y

za z

zb

zc 1

(concluded 1

Figure 9 - Graphical

COPYRIGHT 2003; International Organization for Standardization

review

of tolerance

classes for shafts

IT10

in terms of standard

tolerance

-r

grades

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

IT11

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

IT9

286-2 : 1988 (El

--`,```,``,,,,`,,,`,,`,,``,,,`-`-`,,`,,`,`,,`---

IS0

UDC

621.753N.2

Descriptors

: dimensional tolerances,

fits, standard tolerances,

dimensions.

Price based on 43 pages

COPYRIGHT 2003; International Organization for Standardization

Document provided by IHS Licensee=Shell Services International B.V./5924979112, User=, 03/17/2003 06:02:52 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

View more...

Comments

Copyright ©2017 KUPDF Inc.
SUPPORT KUPDF