Indesit Wg 1031tpr service manual
May 31, 2016 | Author: Andrea_Diaco_4695 | Category: N/A
Short Description
Indesit Wg 1031tpr service manual...
Description
Model type: WG1031TPR Commercial code: 21522
page 1
General notes
Technical Documentation guidelines
------------------------------------------------------------------------------------------------------------------------------You can find herewith some generic information to simplify cunsulting of technical documentation: 1. Models of same range share the same exploded views, which report the richest set of spare parts:generally, a model does not necessarly have a related spare part for each particular shown on exploded views. 2. Some spare parts can not be represented directly on the exploded views (instruction booklets, specific kit, etc...). You can find those codes in the spare parts list with the same reference of particular where spares are installed or with references 099, 999. Instruction booklets, once managed, appear with 000 reference. 3. On the higher right site of each exploded view there is a serial number which indicates the beginning of the production of certain range:some models might have more than an exploded view for a given category, each distinguished by a different serial no.and linked to another spare parts list, In this case, serial no. is required to supply the right spare part code. Exploded view to be considered is the one with a more recent serial no. but previous than the one of the model that needs assistance. 4.Exploded views might require further updates even after publishing. Addition of new spares will go on following the already existing numeration references. Revision number of an exploded view is shown into last four digits of serial number into upper right hand corner. 5.The spare parts list associated to an exploded view shows related codes of spares managed for a certain model; for each spare part other informations are available: REF: reference no of spare into a table; SUBSTITUTE: list of spare(s) which can replace a code but that keeps same functional characteristics INDUSTRIAL CODE: list of variables of a model (shown into model label) where such spare is used; NOTICE: code of information(s) to refer to complete technical intervention, track for changes or to find correct spare part code. 6. Some notices, into a same section are generic therefore cannot be directly linked to a spare part. In order to assist a model in the best way as possible, it is helpful to pay attention to all notices and constantly verify documentation updates 7.Technical documentation cover shows model name and its commercial codes
page 2
pdf_tavola_title_ENG
cod. 1110150
page 3
Spare parts list
Spare parts list cod. 1110150
Ref.
Code
Substitute
000
C00059873
user instruction booklet russo gbe
000
C00063668
user instructions booklet d
000
C00074568
user instructions booklet rs-gbe-nl-d-fr
000
C00076632
user instructions booklet it
001
C00046947
001
C00066277
worktop white giugiaro (00115)
003
C00059742
dashboard + handle
005
C00046945
timer knob white
006
C00055474
temperature knob white
008
C00046944
009
C00018748
cable clamp
009
C00050186
bracket - pressure switch
011
C00053781
011
1 C00066277
1 C00044735
1 C00064546,1 C00065832
Industrial code
Description
Notice
worktop white giugiaro
push button knob white giugiaro
cabinet white 27 kit
n1040200,n1040058,n10402 00
C00066276
cabinet white
n1040200,n1040058,n10402 00
011
C00083796
cap for electrovalve
n1040200,n1040058,n10402 00
019
C00047092
plinth white giugiaro
029
C00050320
foot - rear m 8 h = 41 mm
031
C00002497
nut m4x3,2x7
031
C00019846
bolt t 1/2 t m4x12
031
C00057568
032
C00057567
hinge plate outer case (wgd80525)
036
C00044085
plug cabinet
037
C00012687
self-tapping screw tsp 3,5x13
1 C00065185
bolt kfr
page 4
038
C00046924
rear cover white
041
C00059869
spring for foot d =11 mm h = 21 mm
046
C00058692
door handle kit e giugiaro
049
C00058702
door frame and glass assy giugiaro
099
C00019849
washer 37x8,5x2
099
C00030392
099
C00040932
self locking nut m6
099
C00044115
spacer l = 34 mm
099
C00056932
bolt
099
C00057566
bolt hi-lo 4 x10
099
C00058925
spacer
099
C00076402
panel paraspray
1 C00030339
rubber cup washer
page 5
pdf_tavola_title_ENG
cod. 1110260
page 6
Spare parts list
Spare parts list cod. 1110260
Ref.
Code
Substitute
001
C00034335
bolt - drum pulley fixing
002
C00034337
washer 10,5 x 21
002
C00058039
washer 10,5 x 25 x 3
003
C00034336
washer d33xd9xsp2
004
C00056948
belt h7 1221 mm
005
C00055043
drum pulley d= 280 mm
006
C00056949
set tub front plastic kit
009
C00038453
011
C00040897
tank cover lid seal - plastic tank
012
C00036059
stainless drum
013
C00047133
suspension spring anchorage pad white
014
C00014342
bolt m8x75 te
n1040235,n1040235,n10401 84
014
C00055019
bolt m8x60 te
n1040235,n1040235,n10401 84
014
C00081630
self-tapping screw l 60 / 56 mm x 9,5
n1040235,n1040235,n10401 84
015
C00055018
washer m8
n1040184,n1040235
016
C00058677
017
C00055017
018
C00054767
019
1 C00038358,1 C00089734
1 C00104428
Industrial code
Description
Notice
n1040235,n1040184
bearing spider - on drum
bolt m8x8,8x90 tank spring
1 C00063246
upper counterweight kg 13,8 red
n1040045
C00055038
plate
n1040235
020
C00055032
plastic tank kit
n1040235,n1040184,n10402 35,0111115,n1040179,n104
020
C00066420
plastic tank kit
n1040235,n1040184,n10402 35,0111115,n1040179,n104
020
C00081216
bush diameter 10 mm kit
n1040235,n1040184,n10402 35,0111115,n1040179,n104
021
C00103656
hose - dispenser to tank
page 7
022
C00057933
bellows clamp (tank front)
023
C00057932
bellows seal
024
C00032708
plastic insert nut - case front
024
C00046961
clamping ring - bellows seal front
024
C00064546
clamping ring - bellows seal front
025
C00054768
025
1 C00081633
front counterweight 9,8 kg.
n1040184,n1040235,n10402 35
C00081633
front counterweight 9,8 kg.
n1040184,n1040235,n10402 35
026
C00054777
hose-tank to pump
027
C00030446
bolt m10 x 45 zntr
028
C00055039
shock absorber 120 n
029
C00030680
030
C00055037
plastic expansion rivet
031
C00042410
clamping band tank cover lid
032
C00040935
lock nut m8
033
C00038450
034
C00014917
grommet - thermostat
034
C00040928
safety thermostat gasket
035
C00055397
support
037
C00104261
hose clamp
038
C00058676
washer 8,4x14x1,6
039
C00055040
040
C00065152
nut romob m6x20x1,6
041
C00066597
earth plate
042
C00066691
1 C00040130
1 C00089735
1 C00055039
1 C00090555
nut m 10 n1040052,n1040058
drum + spider assembly 600800-1000 rpm
shock absorber support
bearing kit
n1040059
page 8
pdf_tavola_title_ENG
cod. 1110310a
page 9
Spare parts list
Spare parts list cod. 1110310a
Ref.
Code
002
Substitute
Description
Notice
C00043435
radio interference suppressor
n1040058
002
C00064559
radio interference suppressor
n1040058
003
C00024521
suplly cable 3x1,5 nf
n1040058
003
C00064563
supply cable 3x1 schuko 1,5 m
n1040058
004
C00059743
wiring + timer eaton ec 4684
005
C00030357
pb/switch(ch/over 1 pole e1533) nc+na
005
C00030358
on-off switch(na+na 2pole e0040)
005
C00031061
switch nc sin.pole e1284
005
C00053079
deviator switch nc+na+resistor 3 kohm
006
C00019749
indicator lamp
008
C00041163
terminal block
009
C00054735
timer eaton ec 4684
010
C00019650
adjustable thermostat
011
C00050186
bracket - pressure switch
011
C00054737
pressure swit.i/140-110 ii/205120 iii/27
012
C00047066
metal operating rod
013
C00047069
additive cover
014
C00047068
015
C00019755
015
C00034325
016
C00051446
016 017
1 C00075352
Industrial code
detergent drawer anti-vibration bush (foam)
n1040028
1 C00103834
pressure switch hose l 560 mm
n1040028
1 C00066454
digital module 5520 5520/u
n1040060
C00066454
digital module 5520 5520/u triac 12 a.
n1040060
C00011140
door interlock flange black
page 10
020
C00066285
1 C00081780,1 C00087885
021
C00040931
bush - motor pivot (plastic)
022
C00043430
tacho generator black for ice motor
022
C00047317
brush for motor (ice)..940n2101/940n1i01
022
C00056962
motor ice 850/1000 rpm
024
C00041843
washer 8,5x17x1,5
024
C00050187
fixing nut
024
C00052497
bolt m6x30
024
C00104675
motor rubber bush
028
C00046974
029
C00027466
drain hose - to sink l=1860mm
030
C00058678
hose
031
C00019902
plastic -u- to make drain hose hook
032
C00003070
mains inlet hose cold 25c 10bar 1500 mm
034
C00005572
sealing washer-mains inlet hose
036
C00028568
diverter pivot arm 18 teeth
037
C00019708
dispenser spring
038
C00028569
diverter quadrant 19 teeth
040
C00019732
dispenser diverter
041
C00052771
dispenser body + cover assy kit
042
C00046980
electrovalve 1 way 8lt 220 v
043
C00055046
heating element 2000w 230 v
n1040058
044
C00055036
protection oven botton heating element
n1040058
045
C00055041
thermostat 1 t 95ø nc
n1040058
049
C00045023
filter handle
050
C00045025
filter seal
051
C00045027
filter element kit
052
C00044998
self cleaning pump 240v./50hz.
052
C00085618
053
C00050197
bracket condenser/suppressor
099
C00013562
tube clamp 15,1-15,9
1 C00015858
1 C00092264
heating element+termal cutout 2000w/230v
thermostat 1t 40øc na
self cleaning pump 240v./50hz.idc
page 11
Notices
n1040028 Pressure switch hose and shock absorber
------------------------------------------------------------------------------------------------------------------------------Beginning from serial no. 90517.0001 the models related to the notice have been using the pressure switch hose (L=530 mm) with the addition of a shock absorber.
Codes of shock absorbers used: Code 034325 - Pressure switch hose (L=580 mm) * Code 019755 - Shock absorber.
*In order to reduce the number of parts handled by the SAT, the documentation shows the code of the pressure switch hose (L=580 mm). The person in charge of assistance will have to cut the new hose as needed, according to the dimensions given in this Notice.
n1040045 Dispenser lid and counterweights
------------------------------------------------------------------------------------------------------------------------------Beginning with serial no. 90825.0001, on 600 rpm Washing machines manufactured at the Teverola factory, the following parts have been used:
Part no. 056949 - Plastic dispenser lid kit; Part no. 054768 - Front counterweight 9.8 Kg; Part no. 063246 - Upper counterweight 14.5 Kg.
The counterweights part nos. 054768 and 063246, if used together, can be used instead of the pre-modification ones (in order: 056440 and page 12
054767) which will only continue to be handled until stocks run out. The dispenser lid part no. 056949 can be used instead of the previous one (part no. 056442) and 063244 used on other models from which it is different, in that it has two thermostat holes instead of just the one. If the model being repaired only requires the use of one thermostat, the hole for the second one should be closed with the plug (part no. 020181) provided in the kit.
n1040052 Modification of the expander shaft.
------------------------------------------------------------------------------------------------------------------------------Beginning with serial no. 91115.0001, in order to improve the fixing of the shock absorber onto the tub, the diameter of the end part of the expander's shaft was increased by 0.2 mm on the Washing machines with plastic tubs manufactured at the Teverola factory. The new part is handled with the same SAT code 055037 as the pre-modification one and can be used, applying a drop of Super Attac adhesive on the end part of the shaft which is to be inserted into the expander upon blocking it.
n1040058 Various modifications (Plastic tub without safety thermostat hole, new supply cable and radio interference suppresser complete with terminal board).
------------------------------------------------------------------------------------------------------------------------------Beginning with serial no. 00110.0001, a few modifications have been made to washing machines manufactured at the Teverola factory. These modifications mainly affected the cabinet (on which the perforation of the terminal board was modified) and the tub (from which the hole and the safety thermostat were removed) and a new heating element with fuse was used. The new parts, except for the worktop, cannot be used on their own on pre-modification appliances because the cabinet has to have the supply cable moulded together as well as the radio interference suppresser and the quick connection condenser, whereas for the tub it is absolutely necessary to use the heating element with fuse. However, to carry out this intervention, the wiring needs to be modified in the following way: 1) Discard the wire leading from the safety thermostat to the heating element. 2) Disconnect the wire that leads from the wiring to the safety thermostat and insert it onto the contact of the new heating element on which the fuse is placed (it can be recognised by the green insulating sheath on 230 V models and the blue one on 240 Volt models). The pre-modification parts shall continue to be handled until stocks run out. The following table has been attached in order to make it simpler to identify the parts necessary for the use of a new cabinet or of a new tub on premodification appliances.
page 13
n1040059 Kit of bearings plus sealing ring for appliances with a plastic tub.
------------------------------------------------------------------------------------------------------------------------------The kit of bearings plus sealing ring part no. 066691 (cod. 090554 Kit 600-800 and cod. 090555 Kit 800-1000) has been coded to apply the bearings onto appliances with a plastic tub, thus avoiding having to necessarily replace the tub as well as the lid, due to possible deformations caused by hot wash cycles that make the coupling of the two parts impossible. Once the bearings have been extracted, take particular care in making sure that the housing of the bearings does not constitute a deformed surface, in which case the tub and lid should both be replaced. To ensure that the sealing ring is perfectly watertight, it is essential that you use around 7 gr. of Amblig TA grease which must be distributed evenly among the surfaces of the bearings that are in contact with the sealing ring and in the central hole of the ring itself.
n1040060 Remco modules with 12 A Triac
------------------------------------------------------------------------------------------------------------------------------Beginning with serial no. 00217.0001, the following modules with 12 A triac have been used on appliances produced at the Comunanza / Teverola factory:
Part no. 066454 - REMCO 5520 Part no. 066455 - REMCO 5521 Part no. 066456 - REMCO 5530 Part no. 066457 - REMCO 5531
page 14
The new modules can be used instead of the corresponding pre-modification modules, which will continue to be handled normally until stocks run out.
Part no. 051446 - REMCO 5520 Part no. 056332 - REMCO 5521 Part no. 053085 - REMCO 5530 Part no. 056333 - REMCO 5531.
n1040179 Kit of Small Steel Sleeves for spring eyelets on plastic tubs.
------------------------------------------------------------------------------------------------------------------------------If on the apparatus' with plastic tubs with registration number previous to 81001.0001, the wearing of the spring eyelet shows (caused by an anomalous rubbing of the spring on the plastic), a Kit of small steel bushes been realized (Diameter 10 mm X Length 10 mm) Code 081216. The two small sleeves that are part of the kit have to be inserted in interference to the spring eyelets (see Letter A in following figure)when signs that these have being used are visible. The solution is effective even if the ring is completely cut.
n1040184 Modification of counterweight fixing on front plastic tubs.
------------------------------------------------------------------------------------------------------------------------------From the registration no. 10320.0001, the front counterweight fixing system has been modified, on Washing machines with plastic tubs produced in page 15
the Teverola factory plant, that now is achieved via the use of three self-tapping screws code 081630. This modification has affected the following items : Tubs code 066420 and 066530. The modified tubs retain the same SAT pre-modification code and will be handled until stock depletion and are equipped with the respective fixing screws; Pre-modified tubs equipped with the following items: Qty. 3 Screws code 014342; Qty. 3 Conical washers code 055018; Qty. 3 Plain washers code 034336.
Modified tubs, equipped with the following items: Qty. 3 Self-tapping screws code 081630. Front counterweight. The modified front counterweight code 081633 may be used in place of the pre-modification counterweight code 054768 but not vice versa, the premodification counterweight will continue to be handled until stock depletion. Each time in a modified tub it is necessary to unscrew the self-tapping screws that stop the front counterweight , effecting again the fixing and avoiding a possible loosening in time of the tub and consequently its break , it has to be used screws code 014342, conical washers code 055018, plain washers code 034336 and plates code 055038.
n1040200 Electrovalve drill hole plug for Teverola production cabinets.
------------------------------------------------------------------------------------------------------------------------------From the registration no. 10601.0001 on all Washing machines produced in the Teverola plant have been using cabinets with two electrovalve drill holes. If the model produced provides for one only electrovalve, then one drill hole is capped by using the appropriate plug code 083796. The cabinets handled by After Sales Service with two electrovalve drill holes where used on models with one only electrovalve should use the plug.
n1040223 Discharge pump "RAST5" for Teverola washing machines page 16
------------------------------------------------------------------------------------------------------------------------------From the registration no. 11022.0001, the Teverola produced washing machines involved by the present Notice, will use new discharge pumps code 085618 and 085617 in substitution respectively to the preceding codes: 044998 and 050334. The new pumps may be used in place of the preceding pumps ensuring that the terminals are equipped with faston covers. The pre-modification pumps will be handled regularly until stock depletion.
n1040235 Restored the fixing of the anterior counterweight with platelets inserted in the tub
------------------------------------------------------------------------------------------------------------------------------From the 11105.0001 registration number on the washing machines with plastic tubs produced in the Teverola factory, the fixing of the anterior counterweight is restored with platelets inserted in the tub instead of those realised with self-threading screws, the system described in Notice N1040184. The tubs maintain the same SAT code and are provided with the following particulars:
N° 3 Screws code cod. 014342; N° 3 Conical washer cod. 055018; N° 3 Plain washer cod. 034336.
Whenever the necessity may arise on a tub, proceed with diverting the self-threading screws that block the anterior counterweight., as it's compulsory to execute the fixing again avoiding in time a possible loosening and thus the breaking of the tub by utilising the registered screws (cod. 014342), the conical washers (cod. 055018), the plain washers (cod. 034336) and the platelets (cod. 055038).
0111115 NOTICES FOR PLASTIC TUBS
------------------------------------------------------------------------------------------------------------------------------WASHING MACHINE WITH PLASTIC TUB ---Correct installation of the belt: In order to install the belt properly, it must be positioned at the centre of the drum pulley or towards the exterior of the machine (at least 3 mm from the inner edge of the pulley). This is to prevent the belt from slipping off the pulley. This procedure must be followed because the plastic parts (tank and tank cover) undergo distortion during the heating phase of the cycle, which inclines the top part of the pulley 3 mm away from the cover of the tank.
page 17
---Replacement of the tank or the cover back: During cycles using hot water, the tank and cover undergo distortion, which makes it impossible for either of the parts to be used with a new replacement part. Therefore, if either of the two is faulty, BOTH must be replaced. ---Tightening torques for plastic drums: Drive pulley - 550 (N X dm); Heating element - 20 (N X dm); Clamping band - 120 (N X dm); Shock absorbers - 60 (N X dm); Top counterweight - 110 (N X dm); Bottom counterweight 110 (N X dm); Motor fastener - 45 (N X dm); Packing brackets - 60 (N X dm); Oscillating assembly - 80 (N X dm);
n1040028 Pressure switch hose and shock absorber
------------------------------------------------------------------------------------------------------------------------------Beginning from serial no. 90517.0001 the models related to the notice have been using the pressure switch hose (L=530 mm) with the addition of a shock absorber.
Codes of shock absorbers used: Code 034325 - Pressure switch hose (L=580 mm) * Code 019755 - Shock absorber.
*In order to reduce the number of parts handled by the SAT, the documentation shows the code of the pressure switch hose (L=580 mm). The person in charge of assistance will have to cut the new hose as needed, according to the dimensions given in this Notice.
n1040045 Dispenser lid and counterweights
------------------------------------------------------------------------------------------------------------------------------page 18
Beginning with serial no. 90825.0001, on 600 rpm Washing machines manufactured at the Teverola factory, the following parts have been used:
Part no. 056949 - Plastic dispenser lid kit; Part no. 054768 - Front counterweight 9.8 Kg; Part no. 063246 - Upper counterweight 14.5 Kg.
The counterweights part nos. 054768 and 063246, if used together, can be used instead of the pre-modification ones (in order: 056440 and 054767) which will only continue to be handled until stocks run out. The dispenser lid part no. 056949 can be used instead of the previous one (part no. 056442) and 063244 used on other models from which it is different, in that it has two thermostat holes instead of just the one. If the model being repaired only requires the use of one thermostat, the hole for the second one should be closed with the plug (part no. 020181) provided in the kit.
n1040052 Modification of the expander shaft.
------------------------------------------------------------------------------------------------------------------------------Beginning with serial no. 91115.0001, in order to improve the fixing of the shock absorber onto the tub, the diameter of the end part of the expander's shaft was increased by 0.2 mm on the Washing machines with plastic tubs manufactured at the Teverola factory. The new part is handled with the same SAT code 055037 as the pre-modification one and can be used, applying a drop of Super Attac adhesive on the end part of the shaft which is to be inserted into the expander upon blocking it.
n1040058 Various modifications (Plastic tub without safety thermostat hole, new supply cable and radio interference suppresser complete with terminal board).
------------------------------------------------------------------------------------------------------------------------------Beginning with serial no. 00110.0001, a few modifications have been made to washing machines manufactured at the Teverola factory. These modifications mainly affected the cabinet (on which the perforation of the terminal board was modified) and the tub (from which the hole and the safety thermostat were removed) and a new heating element with fuse was used. The new parts, except for the worktop, cannot be used on their own on pre-modification appliances because the cabinet has to have the supply cable moulded together as well as the radio interference suppresser and the quick connection condenser, whereas for the tub it is absolutely necessary to use the heating element with fuse. However, to carry out this intervention, the wiring needs to be modified in the following way: 1) Discard the wire leading from the safety thermostat to the heating element.
page 19
2) Disconnect the wire that leads from the wiring to the safety thermostat and insert it onto the contact of the new heating element on which the fuse is placed (it can be recognised by the green insulating sheath on 230 V models and the blue one on 240 Volt models). The pre-modification parts shall continue to be handled until stocks run out. The following table has been attached in order to make it simpler to identify the parts necessary for the use of a new cabinet or of a new tub on premodification appliances.
n1040059 Kit of bearings plus sealing ring for appliances with a plastic tub.
------------------------------------------------------------------------------------------------------------------------------The kit of bearings plus sealing ring part no. 066691 (cod. 090554 Kit 600-800 and cod. 090555 Kit 800-1000) has been coded to apply the bearings onto appliances with a plastic tub, thus avoiding having to necessarily replace the tub as well as the lid, due to possible deformations caused by hot wash cycles that make the coupling of the two parts impossible. Once the bearings have been extracted, take particular care in making sure that the housing of the bearings does not constitute a deformed surface, in which case the tub and lid should both be replaced. To ensure that the sealing ring is perfectly watertight, it is essential that you use around 7 gr. of Amblig TA grease which must be distributed evenly among the surfaces of the bearings that are in contact with the sealing ring and in the central hole of the ring itself.
n1040060 Remco modules with 12 A Triac
------------------------------------------------------------------------------------------------------------------------------Beginning with serial no. 00217.0001, the following modules with 12 A triac have been used on appliances produced at the Comunanza / Teverola factory: page 20
Part no. 066454 - REMCO 5520 Part no. 066455 - REMCO 5521 Part no. 066456 - REMCO 5530 Part no. 066457 - REMCO 5531
The new modules can be used instead of the corresponding pre-modification modules, which will continue to be handled normally until stocks run out.
Part no. 051446 - REMCO 5520 Part no. 056332 - REMCO 5521 Part no. 053085 - REMCO 5530 Part no. 056333 - REMCO 5531.
n1040179 Kit of Small Steel Sleeves for spring eyelets on plastic tubs.
------------------------------------------------------------------------------------------------------------------------------If on the apparatus' with plastic tubs with registration number previous to 81001.0001, the wearing of the spring eyelet shows (caused by an anomalous rubbing of the spring on the plastic), a Kit of small steel bushes been realized (Diameter 10 mm X Length 10 mm) Code 081216. The two small sleeves that are part of the kit have to be inserted in interference to the spring eyelets (see Letter A in following figure)when signs that these have being used are visible. The solution is effective even if the ring is completely cut.
n1040184 Modification of counterweight fixing on front plastic tubs.
------------------------------------------------------------------------------------------------------------------------------From the registration no. 10320.0001, the front counterweight fixing system has been modified, on Washing machines with plastic tubs produced in the Teverola factory plant, that now is achieved via the use of three self-tapping screws code 081630. This modification has affected the following items : page 21
Tubs code 066420 and 066530. The modified tubs retain the same SAT pre-modification code and will be handled until stock depletion and are equipped with the respective fixing screws; Pre-modified tubs equipped with the following items: Qty. 3 Screws code 014342; Qty. 3 Conical washers code 055018; Qty. 3 Plain washers code 034336.
Modified tubs, equipped with the following items: Qty. 3 Self-tapping screws code 081630. Front counterweight. The modified front counterweight code 081633 may be used in place of the pre-modification counterweight code 054768 but not vice versa, the premodification counterweight will continue to be handled until stock depletion. Each time in a modified tub it is necessary to unscrew the self-tapping screws that stop the front counterweight , effecting again the fixing and avoiding a possible loosening in time of the tub and consequently its break , it has to be used screws code 014342, conical washers code 055018, plain washers code 034336 and plates code 055038.
n1040200 Electrovalve drill hole plug for Teverola production cabinets.
------------------------------------------------------------------------------------------------------------------------------From the registration no. 10601.0001 on all Washing machines produced in the Teverola plant have been using cabinets with two electrovalve drill holes. If the model produced provides for one only electrovalve, then one drill hole is capped by using the appropriate plug code 083796. page 22
The cabinets handled by After Sales Service with two electrovalve drill holes where used on models with one only electrovalve should use the plug.
n1040235 Restored the fixing of the anterior counterweight with platelets inserted in the tub
------------------------------------------------------------------------------------------------------------------------------From the 11105.0001 registration number on the washing machines with plastic tubs produced in the Teverola factory, the fixing of the anterior counterweight is restored with platelets inserted in the tub instead of those realised with self-threading screws, the system described in Notice N1040184. The tubs maintain the same SAT code and are provided with the following particulars:
N° 3 Screws code cod. 014342; N° 3 Conical washer cod. 055018; N° 3 Plain washer cod. 034336.
Whenever the necessity may arise on a tub, proceed with diverting the self-threading screws that block the anterior counterweight., as it's compulsory to execute the fixing again avoiding in time a possible loosening and thus the breaking of the tub by utilising the registered screws (cod. 014342), the conical washers (cod. 055018), the plain washers (cod. 034336) and the platelets (cod. 055038).
0111115 NOTICES FOR PLASTIC TUBS
------------------------------------------------------------------------------------------------------------------------------WASHING MACHINE WITH PLASTIC TUB ---Correct installation of the belt: In order to install the belt properly, it must be positioned at the centre of the drum pulley or towards the exterior of the machine (at least 3 mm from the inner edge of the pulley). This is to prevent the belt from slipping off the pulley. This procedure must be followed because the plastic parts (tank and tank cover) undergo distortion during the heating phase of the cycle, which inclines the top part of the pulley 3 mm away from the cover of the tank. ---Replacement of the tank or the cover back: During cycles using hot water, the tank and cover undergo distortion, which makes it impossible for either of the parts to be used with a new replacement part. Therefore, if either of the two is faulty, BOTH must be replaced. ---Tightening torques for plastic drums: page 23
Drive pulley - 550 (N X dm); Heating element - 20 (N X dm); Clamping band - 120 (N X dm); Shock absorbers - 60 (N X dm); Top counterweight - 110 (N X dm); Bottom counterweight 110 (N X dm); Motor fastener - 45 (N X dm); Packing brackets - 60 (N X dm); Oscillating assembly - 80 (N X dm);
page 24
Electric schemes and links
Cod. 111279a
page 25
Legend Legend: 111279a
AQS
Aquastop electrovalve
Mzbn/MTA
zbn timer motor
B
Buzzer
N
Neutral or Terminal Board
NC
Spin cycle exclusion
BC BF
Terminal board contact, motor fan and dryer heatin
P
Pressure switch
BP
Buzzer
PA
High speed potentiometer
C
Condensator
PB
Low speed potentiometer
CA
Condensator
PL
Pure Wool
DV
Switching device
PM
Motor Thermoprotector
EF/CL
Electro-Valve Cold Water / Bleach
PR
Timer programmer or Pressure switch
EF/L
Electro-Valve Cold Water / Wash
PS
Drain pump
EF/P
Electro-Valve Cold Water / Prewash
P1
1st level pressure cut-off switch
ER
Exclude Heating Element
P2
2nd level pressure cut-off switch
ET
Thermostat disactivation
R
Heating element
EV
Electrovalve
Ras/RA
Dryer heating element
EVA
Dryer electrovalve
RE
Relay
EVC
Hot water electrovalve
RR
Heating element
EVF
Elettrovalvola acqua fredda
RV
Speed regulator
EVL
Wash electrovalve
S
LED
EVP
Pre Wash electrovalve
SL
Line LED
FA
Antijamming filter
SO
Door LED
FD
Delicate drying cycle thermostat
SR
Heating LED
FE
Strong drying cycle thermostat
ST
Temperature selector
FRT
Thermofusible Heating Element
SV
Speed Selector for Spin
I
Inverter
T
Timer contacts
IA
Switch On/Off
TA
Drying timer contacts
page 26
IC
Switch N.C. - 1/2 Load
TB
Low Temperature Thermostat
ID
Switch display
TC
Spider wheel earth
IE
Water Saving Device
TFL
Flange earth
IF
Switch - Spin Reduction
TG
Main earth
IP
Door switch
TH
Thermostat
IR
Line switch
THF
Operating thermostat
IS
Water-stop
THR
Adjustable thermostat
I1..2..3..
Switches/switching devices
TH1
1st temperature thermostat
L
Line or Lamp
TH2
2nd temperature thermostat
LB
Low Level
TH3
3rd temperature thermostat
LN
Normal Level
TM
Motor earth
LS
Pilot lamp
TMB
Main cabinet earth
M
Earth-symbol
TMP
Motor thermal protector
MC
Spin cycle motor
TMS
Thermostop
MI
MOTOR WITH PULLEY
TP
Thermal protector
ML
Wash cycle motor
TPS
Drain pump earth
MO
Terminal Board
TR
Heating element earth
MP
Door dip-switch
TS
Safety thermostat
MR
Thermal Lock
TT
Timer earthing connection
MT
Timer motor
TTH
Earthing Thermostat
MV
Motor fan
TV
Tank earth
MV -Ras
Dryer heating element
ZBN
Timer
page 27
Electric schemes and links
Cod. 111293b
page 28
Legend Legend: 111293b
AQS
Aquastop electrovalve
Mzbn/MTA
zbn timer motor
B
Buzzer
N
Neutral or Terminal Board
NC
Spin cycle exclusion
BC BF
Terminal board contact, motor fan and dryer heatin
P
Pressure switch
BP
Buzzer
PA
High speed potentiometer
C
Condensator
PB
Low speed potentiometer
CA
Condensator
PL
Pure Wool
DV
Switching device
PM
Motor Thermoprotector
EF/CL
Electro-Valve Cold Water / Bleach
PR
Timer programmer or Pressure switch
EF/L
Electro-Valve Cold Water / Wash
PS
Drain pump
EF/P
Electro-Valve Cold Water / Prewash
P1
1st level pressure cut-off switch
ER
Exclude Heating Element
P2
2nd level pressure cut-off switch
ET
Thermostat disactivation
R
Heating element
EV
Electrovalve
Ras/RA
Dryer heating element
EVA
Dryer electrovalve
RE
Relay
EVC
Hot water electrovalve
RR
Heating element
EVF
Elettrovalvola acqua fredda
RV
Speed regulator
EVL
Wash electrovalve
S
LED
EVP
Pre Wash electrovalve
SL
Line LED
FA
Antijamming filter
SO
Door LED
FD
Delicate drying cycle thermostat
SR
Heating LED
FE
Strong drying cycle thermostat
ST
Temperature selector
FRT
Thermofusible Heating Element
SV
Speed Selector for Spin
I
Inverter
T
Timer contacts
IA
Switch On/Off
TA
Drying timer contacts
page 29
IC
Switch N.C. - 1/2 Load
TB
Low Temperature Thermostat
ID
Switch display
TC
Spider wheel earth
IE
Water Saving Device
TFL
Flange earth
IF
Switch - Spin Reduction
TG
Main earth
IP
Door switch
TH
Thermostat
IR
Line switch
THF
Operating thermostat
IS
Water-stop
THR
Adjustable thermostat
I1..2..3..
Switches/switching devices
TH1
1st temperature thermostat
L
Line or Lamp
TH2
2nd temperature thermostat
LB
Low Level
TH3
3rd temperature thermostat
LN
Normal Level
TM
Motor earth
LS
Pilot lamp
TMB
Main cabinet earth
M
Earth-symbol
TMP
Motor thermal protector
MC
Spin cycle motor
TMS
Thermostop
MI
MOTOR WITH PULLEY
TP
Thermal protector
ML
Wash cycle motor
TPS
Drain pump earth
MO
Terminal Board
TR
Heating element earth
MP
Door dip-switch
TS
Safety thermostat
MR
Thermal Lock
TT
Timer earthing connection
MT
Timer motor
TTH
Earthing Thermostat
MV
Motor fan
TV
Tank earth
MV -Ras
Dryer heating element
ZBN
Timer
page 30
Electric schemes and links
Cod. 111293c
page 31
Legend Legend: 111293c
AQS
Aquastop electrovalve
Mzbn/MTA
zbn timer motor
B
Buzzer
N
Neutral or Terminal Board
NC
Spin cycle exclusion
BC BF
Terminal board contact, motor fan and dryer heatin
P
Pressure switch
BP
Buzzer
PA
High speed potentiometer
C
Condensator
PB
Low speed potentiometer
CA
Condensator
PL
Pure Wool
DV
Switching device
PM
Motor Thermoprotector
EF/CL
Electro-Valve Cold Water / Bleach
PR
Timer programmer or Pressure switch
EF/L
Electro-Valve Cold Water / Wash
PS
Drain pump
EF/P
Electro-Valve Cold Water / Prewash
P1
1st level pressure cut-off switch
ER
Exclude Heating Element
P2
2nd level pressure cut-off switch
ET
Thermostat disactivation
R
Heating element
EV
Electrovalve
Ras/RA
Dryer heating element
EVA
Dryer electrovalve
RE
Relay
EVC
Hot water electrovalve
RR
Heating element
EVF
Elettrovalvola acqua fredda
RV
Speed regulator
EVL
Wash electrovalve
S
LED
EVP
Pre Wash electrovalve
SL
Line LED
FA
Antijamming filter
SO
Door LED
FD
Delicate drying cycle thermostat
SR
Heating LED
FE
Strong drying cycle thermostat
ST
Temperature selector
FRT
Thermofusible Heating Element
SV
Speed Selector for Spin
I
Inverter
T
Timer contacts
IA
Switch On/Off
TA
Drying timer contacts
page 32
IC
Switch N.C. - 1/2 Load
TB
Low Temperature Thermostat
ID
Switch display
TC
Spider wheel earth
IE
Water Saving Device
TFL
Flange earth
IF
Switch - Spin Reduction
TG
Main earth
IP
Door switch
TH
Thermostat
IR
Line switch
THF
Operating thermostat
IS
Water-stop
THR
Adjustable thermostat
I1..2..3..
Switches/switching devices
TH1
1st temperature thermostat
L
Line or Lamp
TH2
2nd temperature thermostat
LB
Low Level
TH3
3rd temperature thermostat
LN
Normal Level
TM
Motor earth
LS
Pilot lamp
TMB
Main cabinet earth
M
Earth-symbol
TMP
Motor thermal protector
MC
Spin cycle motor
TMS
Thermostop
MI
MOTOR WITH PULLEY
TP
Thermal protector
ML
Wash cycle motor
TPS
Drain pump earth
MO
Terminal Board
TR
Heating element earth
MP
Door dip-switch
TS
Safety thermostat
MR
Thermal Lock
TT
Timer earthing connection
MT
Timer motor
TTH
Earthing Thermostat
MV
Motor fan
TV
Tank earth
MV -Ras
Dryer heating element
ZBN
Timer
page 33
View more...
Comments
