icc.ipc.2012

NOTICE OF INCORPORATION United States Legal Document ≠ All citizens and residents are hereby advised that this is a legally binding document duly incorporated by reference and that failure to comply with such requirements as hereby detailed within may subject you to criminal or civil penalties under the law. Ignorance of the law shall not excuse noncompliance and it is the responsibility of the citizens to inform themselves as to the laws that are enacted in the United States of America and in the states and cities contained therein. ± « ICC IPC (2012), the International Plumbing Code, as mandated and incorporated by the States and Municipalities including Maryland in the Code of Maryland Administrative Regulations (COMAR), Section 05.02.01.02.

2012 International Plumbing Code Errata (Portions of text and tables not shown are unaffected by the errata)

1st and 2nd PRINTING (October 10, 2012) LEGISLATION (page xi) Section 2: Section 305.64.1 Section 90403.1

2012 International Plumbing Code Errata

2012 International Plumbing Code Errata FIRST PRINTING (Updated May 13, 2011)

CHAPTER 2 Add “[A]” preceding the APPROVED definition REDUCED PRESSURE PRINCIPLE BACKFLOW PREVENTER PREVENTION ASSEMBLY  

 

2012 International Plumbing Code Errata (Portions of text and tables not shown are unaffected by the errata)

1st PRINTING (Posted: August 19, 2011) CHAPTER 3 GENERAL REGULATIONS 308.5 Interval of support…. Exception:…Section 105.4 316.1.

2012 International Plumbing Code Errata

Page 1 of 1

2012 International Plumbing Code Errata (Portions of text and tables not shown are unaffected by the errata)

1st and 2nd PRINTING (Posted: September 14, 2012) CHAPTER 4 FIXTURES, FAUCETS AND FIXTURE FITTINGS 403.5 Drinking fountain location. Drinking fountains….500 feet (152 400 mm) of the…

st

nd

2012 International Plumbing Code Errata – 1 & 2 printing 403.5

Page 1 of 1

2012 International Plumbing Code Errata (Portions of text and tables not shown are unaffected by the errata)

1st and 2nd PRINTING (Posted: September 13, 2012) CHAPTER 4 FIXTURES, FAUCETS AND FIXTURE FITTINGS

410.1 Approval. Drinking fountains shall conform to ASME A112.19.1/CSA B45.2 or ASME A112.19.2/CSA B45.1 and water coolers shall conform to ARI AHRI 1010.

2012 International Plumbing Code Errata

Page 1 of 1

2012 International Plumbing Code Errata (Portions of text and tables not shown are unaffected by the errata)

1st and 2nd PRINTING (Posted: 06-06-2012) CHAPTER 4 FIXTURES, FAUCETS AND FIXTURE FITTINGS Table 403.1 TABLE 403.1 MINIMUM NUMBER OF REQUIRED PLUMBING FIXTURES (See Sections 403.2 1.1 and 403.3 2) Correction is applicable to title shown on multiple pages.

2012 International Plumbing Code Errata

Page 1 of 1

2012 International Plumbing Code Errata (Portions of text and tables not shown are unaffected by the errata) 2nd PRINTING (07-11-12) CHAPTER 6 WATER SUPPLY AND DISTRIBUTION [E]607.2.1 Hot water system controls. Automatic circulating hot water system pumps or heat trace shall be arranged to be conveniently turned off automatically or manually when there is limited hot water system demand is not in operation. Ready access shall be provided to the operating controls. [E] 607.5 Pipe Insulation. For automatic-circulating Hot water and heat-traced systems, piping in automatic temperature maintenance systems shall be insulated with not less than 1 inch (25 mm) of insulation having a conductivity not exceeding 0.27 Btu per inch/h ● ft2 ●°F (1.53 W per 25 mm/m2 ● K). The first 8 feet (2438 mm) of hot water piping in nonhot-water-supply temperature maintenance systems served by equipment without integral from a hot water source that does not have heat traps shall be insulated with 0.5 inch (12.7 mm) of material having a conductivity not exceeding 0.27 Btu per inch/h ● ft2 ●°F (1.53 W per 25 mm/m2 ● K). Exception: Heat-traced piping systems shall meet the insulation thickness requirements per the manufacturer’s installation instructions. Untraced piping within a heat traced system shall be insulated with not less than 1 inch (25 mm) of insulation having a conductivity not exceeding 0.27 Btu per inch/h ● ft2 ●°F (1.53 W per 25 mm/m2 ● K). Note: Language for these sections changes back to 1st printing language.

2012 International Plumbing Code Errata

Page 1 of 1

2012 International Plumbing Code Errata (Portions of text and tables not shown are unaffected by the errata)

1st and 2nd PRINTING (07-11-12) CHAPTER 6 WATER SUPPLY AND DISTRIBUTION

613.1 Temperature-actuated mixing valves. Temperature-actuated mixing valves, which are installed to reduce water temperatures to defined limits, shall comply with ASSE 1017. Such valves shall be installed at the hot water source.

2012 International Plumbing Code Errata

Page 1 of 2

2012 International Plumbing Code Errata (Portions of text and tables not shown are unaffected by the errata) 1st PRINTING (Posted: 01-20-2012) CHAPTER 6 WATER SUPPLY AND DISTRIBUTION [E]607.2.1 Hot water system controls. Automatic Circulating hot water system pumps or heat trace shall be arranged to be conveniently turned off automatically or manually when there is limited hot water system demand is not in operation. Ready access shall be provided to the operating controls.

2012 International Plumbing Code Errata

Page 1 of 1

2012 International Plumbing Code Errata (Portions of text and tables not shown are unaffected by the errata) 1st PRINTING (Posted: 01-23-2012) CHAPTER 6 WATER SUPPLY AND DISTRIBUTION [E] 607.5 Pipe Insulation. For automatic-circulating hot water and heat-traced systems, piping in automatic temperature maintenance systems shall be insulated with not less than 1 inch (25 mm) of insulation having a conductivity not exceeding 0.27 Btu per inch/h ● ft2 ●°F (1.53 W per 25 mm/m2 ● K). The first 8 feet (2438 mm) of hot water piping in nonhot-water-supply temperature maintenance systems served by equipment without integral from a hot water source that does not have heat traps shall be insulated with 0.5 inch (12.7 mm) of material having a conductivity not exceeding 0.27 Btu per inch/h ● ft2 ●°F (1.53 W per 25 mm/m2 ● K). Exception: Heat-traced piping systems shall meet the insulation thickness requirements per the manufacturer’s installation instructions. Untraced piping within a heat traced system shall be insulated with not less than 1 inch (25 mm) of insulation having a conductivity not exceeding 0.27 Btu per inch/h ● ft2 ●°F (1.53 W per 25 mm/m2 ● K).

2012 International Plumbing Code Errata

Page 1 of 1

2012 International Plumbing Code Errata (Portions of text and tables not shown are unaffected by the errata)

1st and 2nd PRINTING (07-11-12) CHAPTER 9 VENTS 915.3 2.2 Size and length. The size of a combination waste and vent pipe shall be not less than that indicated in Table 915.3 2.2. The horizontal length of a combination waste and vent pipe shall be unlimited. 915.2.2 3 Connection. The combination waste and vent…. The horizontal length of a combination waste and vent system shall be unlimited. 915.2.3 4 Vent size. 915.2.4 2.5 Fixture branch or drain. Table 915.3 TABLE 915.3 2.2 SIZE OF COMBINATION WASTE AND VENT PIPE

2012 International Plumbing Code Errata

Page 2 of 2

2012 International Plumbing Code Errata (Portions of text and tables not shown are unaffected by the errata)

1st PRINTING (11-28-2011) CHAPTER 9 VENTS 915.2.3 Vent size. The vent shall be sized for the total drainage fixture unit load in accordance with Section 916.2 906.2.

2012 International Plumbing Code Errata

Page 1 of 1

2012 International Plumbing Code Errata (Portions of text and tables not shown are unaffected by the errata)

1st PRINTING (Posted: August 11, 2011) CHAPTER 10 TRAPS, INTERCEPTORS AND SEPARATORS 1003.4.2.2 Garages and service stations. ….area to be drained, plus 1 cubic foot (0.028 m3) for each….

2012 International Plumbing Code Errata

Page 1 of 1

2012 International Plumbing Code Errata (Portions of text and tables not shown are unaffected by the errata)

1st and 2nd PRINTING (November 12, 2012) CHAPTER 11 STORM DRAINAGE

1111.2 Control Devices. ….flow as indicated in Section 1109.1 1110.1.

2012 International Plumbing Code Errata

Page 1 of 1

2012 International Plumbing Code Errata (Portions of text and tables not shown are unaffected by the errata)

1st and 2nd PRINTING (October 18, 2012) CHAPTER 14 REFERENCED STANDARDS

CSA B64.10—07

Manual for the Selection and Installation of Backflow Prevention Devices Preventers

B64.10.1 – 01 07 Manual for the Selection, Installation, Maintenance and Field Testing of Backflow Prevention Devices Preventers

2012 International Plumbing Code Errata

2012 International Plumbing Code Errata (Portions of text and tables not shown are unaffected by the errata)

1st PRINTING (Posted: 01-05-2012) CHAPTER 14 REFERENCED STANDARDS ASME A112.18.6/CSA B125.6 – 2010 09 A112.19.9M -1991 (R2002) Nonvitreous Ceramic Plumbing Fixtures with 2002 Supplement

2012 International Plumbing Code Errata

Page 1 of 1

2012 International Plumbing Code Errata (Portions of text and tables not shown are unaffected by the errata)

1st through 4th PRINTING (Posted: 11-11-13) APPENDIX E SIZING OF WATER PIPING SYSTEM FIGURE E103.3(7) FRICTION LOSS IN FAIRLY ROUGH PIPEa

2012 International Plumbing Code Errata

2012 International Plumbing Code Errata (Portions of text and tables not shown are unaffected by the errata)

1st and 2nd PRINTING (November 12, 2012) APPENDIX E SIZING OF WATER PIPING SYSTEM

Table E103.3(1) Line D, Column 1

2012 International Plumbing Code Errata

Tap in main loss (Table E103A E103.3(4))

Page 1 of 1