HONDA Fit Specs

2008 Honda Fit 2007-08 GENERAL INFORMATION Specifications - Fit

2007-08 GENERAL INFORMATION Specifications - Fit

STANDARDS AND SERVICE LIMITS ENGINE ELECTRICAL ENGINE ELECTRICAL SPECIFICATIONS Item Measurement Qualification Ignition coil Rated voltage Firing order Spark plug Type

Ignition timing

Drive belt NOTE: At engine cold condition

Gap At idle Check the red M/T(in neutral) mark A/T(in N or P position) Deflection with 98 N With A/C (10 kgf, 22 lbf) applied mid way Without A/C between pulleys Tension (measured with belt tension gauge)

Alternator

Starter

Output

At 13.5 V and normal engine temperature Coil (rotor) resistance At 68°F (20°C) Slip ring O.D. Brush length Brush spring tension Output Commutator mica depth Commutator runout Commutator O.D. Brush length Brush spring tension

Standard or New Service Limit 12V 1-3-4-2 NGK: IZFR6K13 DENSO: SKJ20DR-M13 1.2-1.3 mm (0.042-0.051 in.) 8 ± 2° BTDC 8 ± 2° BTDC Used belt: 5.5-8.5 mm (0.22-0.33 in.) New belt: 3.5-5.0 mm (0.14-0.20 in.) Used belt: 7.5-10.5 mm (0.30-0.41 in.) New belt: 4.5-6.0 mm (0,18-0.24 in.) Used belt: 441-588 N (45-60 kgf, 99132 lbf) New belt: 980-1,078 N (100-110 kgf, 220-242 lbf) 90 A

1.84-2.10 ohms 22.7 mm (0.89 in.) 21.2 mm (0.83 in.) 19.0 mm (0.75 in.) 5.0 mm (0.20 in.) 3.3-4.1 N (0.34-0.42 kgf, 0.75-0.93 lbf) 1.0 kW 0.50-0.80 mm 0.20 mm (0.008 (0.020-0.031 in.) in.) 0.02 mm (0.001 in.) 0.05 mm (0.002 max. in.) 28.0 mm (1.10 in.) 27.0 mm (1.06 in.) 14.0-14.5 mm 9.0 mm (0.35 in.) (0.55-0.57 in.) 13.7-17.7 N (1.40-1.80 kgf, 3.09-3.97 lbf)

me Saturday, May 16, 2009 9:33:59 9:33:56 AM

Page 1

© 2005 Mitchell Repair Information Company, LLC.

2008 Honda Fit 2007-08 GENERAL INFORMATION Specifications - Fit

ENGINE ASSEMBLY ENGINE ASSEMBLY SPECIFICATIONS Item Measurement Compression

Qualification

Pressure Check the engine with the starter cranking

Standard or New

Minimum

980 kPa (10.0 kgf/cm2 , 142 psi)

Maximum variation

200 kPa (2.0 kgf/cm2 , 28 psi)

CYLINDER HEAD CYLINDER HEAD SPECIFICATIONS Item Measurement Qualification Warpage Head

Camshaft-to-holder oil clearance Total runout

0.03 mm (0.001 in.) max.

End play

Cam lobe height

Clearance (cold)

Valve

0.07 mm (0.0028 in.) 119.9-120.1 mm (4.7204.728 in.) 0.05-0.25 mm (0.002-0.010 in.) 0.045-0.084 mm (0.00180.0033 in.)

Height

Camshaft

Standard or New

Stem O.D.

Stem-to-guide clearance

Valve seat Width

Intake, primary 35.3799 mm (1.39291 in.) Intake, 30.5291 mm (1.20193 in.) secondary Exhaust 35.3877 mm (1.39321 in.) 0.15-0.19 mm (0.006-0.0007 Intake in.) 0.26-0.30 mm (0.010-0.012 Exhaust in.) 5.48-5.49 mm (0.2157Intake 0.2161 in.) 5.45-5.46 mm (0.2146Exhaust 0.2150 in.) 0.020-0.050 mm (0.0008Intake 0.0020 in.) 0.050-0.080 mm (0.0020Exhaust 0.0031 in.) 0.850-1.150 mm (0.0335Intake 0.0453 in.) 1.250-1.550 mm (0.0492Exhaust 0.0610 in.)

Service Limit 0.08 mm (0.003 in.) 0.5 mm (0.02 in.) 0.100 mm (0.004 in.) 0.04 mm (0.002 in.) 5.45 mm (0.215 in.) 5.42 mm (0.213 in.) 0.08 mm (0.003 in.) 0.11 mm (0.004 in.) 1.60 mm (0.063 in.) 2.00 mm (0.079 in.)

me Saturday, May 16, 2009 9:33:56 AM

Page 2

© 2005 Mitchell Repair Information Company, LLC.

2008 Honda Fit 2007-08 GENERAL INFORMATION Specifications - Fit

46.1-46.5 mm (1.815-1.831 in.) 46.2-46.6 mm (1.819-1.835 in.) 50.52 mm (1.989 in.) 57.37 mm (2.259 in.) 5.51-5.53 mm (0.217-0.218 in.) 5.51-5.53 mm (0.217-0.218 in.) 15.85-16.35 mm (0.6240.644 in.) 15.85-16.35 mm (0.6240.644 in.) 0.019-0.058 mm (0.00070.0023 in.) 0.019-0.058 mm (0.00070.0023 in.)

Intake Stem installed height Exhaust Valve spring

Free length

Intake Exhaust Intake

I.D. Exhaust

Valve guide

Intake Installed height Exhaust Intake

Rocker arm Arm-to-shaft clearance Exhaust

46.8 mm (1.843 in.) 46.9 mm (1.846 in.) 5.55 mm (0.219 in.) 5.55 mm (0.219 in.) 0.08 mm (0.003 in.) 0.08 mm (0.003 in.)

ENGINE BLOCK ENGINE BLOCK SPECIFICATIONS Item Measurement

Qualification

Warpage of deck Bore diameter Block

Standard or New 0.07 mm (0.003 in.) max. 73.00-73.02 mm (2.8740-2.8748 in.)

Bore taper

-

Reboring limit

-

Skirt O.D. at 16 mm (0.6 in.) from bottom of skirt

72.98-72.99 mm (2.8732-2.8736 in.) 0.010-0.040 mm (0.0004-0.0016 in.) 1.050-1.060 mm (0.0413-0.0417 in.) 1.220-1.230 mm (0.0481-0.0484 in.) 2.005-2.020 mm (0.0789-0.0795 in.) 0.065-0.090 mm (0.0026-0.0035 in.)

Clearance in cylinder Piston

Top Ring groove width

Second Oil

Ring-to-groove clearance

Top

Service Limit 0.10 mm (0.004 in.) 73.07 mm (2.8767 in.) 0.05 mm (0.002 in.) 0.25 mm (0.01 in.) 72.97 mm (2.8728 in.) 0.05 mm (0.002 in.) 1.08 mm (0.043 in.) 1.250 mm (0.0492 in) 2.050 mm (0.0807 in.) 0.15 mm (0.006 in.)

me Saturday, May 16, 2009 9:33:56 AM

Page 3

© 2005 Mitchell Repair Information Company, LLC.

2008 Honda Fit 2007-08 GENERAL INFORMATION Specifications - Fit

Second Top Piston ring Ring end gap

Second Oil

O.D. Piston pin Pin-to-piston clearance Pin-to-rod interference Connecting rod

Small-end bore diameter Large-end bore diameter End play installed on crankshaft Main journal diameter Rod journal diameter

0.030-0.055 mm (0.0012-0.0022 in.) 0.15-0.30 mm (0.0060.012 in.) 0.35-0.50 mm (0.0140.020 in.) 0.20-0.70 mm (0.0080.028 in.) 17.996-18.000 mm (0.7085-0.7087 in.) 0.010-0.018 mm (0.0004-0.0007 in.) 0.020-0.036 mm (0.0008-0.0014 in.) 17.964-17.977 mm (0.707-0.708 in.) 43.0 mm (1.69 in.) 0.15-0.30 mm (0.0060.012 in.) 49.976-50.000 mm (1.9676-1.9685 in.) 39.976-40.000 mm (1.5739-1.5748 in.)

Rod/main journal taper

0.005 mm (0.0002 in.)

Rod/main journal out-of-round

0.005 mm (0.0002 in.)

Crankshaft 0.10-0.35 mm (0.0040.014 in.) 0.03 mm (0.0012 in.) max. 0.018-0.036 mm (0.0007-0.0014 in.) 0.020-0.038 mm (0.0008-0.0015 in.)

End play Runout Crankshaft bearing

Main bearing-to-journal oil clearance Rod bearing clearance

0.13 mm (0.005 in.) 0.60 mm (0.024 in.) 0.65 mm (0.026 in.) 0.80 mm (0.031 in.) 0.40 mm (0.016 in.) 0.010 mm (0.0004 in.) 0.010 mm (0.0004 in.) 0.45 mm (0.018 in.) 0.04 mm (0.0016 in.) 0.050 mm (0.0020 in.) 0.050 mm (0.0020 in.)

ENGINE LUBRICATION ENGINE LUBRICATION SPECIFICATIONS item

Measurement Capacity

Engine

Qualification

Service Limit

Standard or New

Engine overhaul 4.2 L (4.4 US qt) Oil change including 3.6 L (3.8 US qt) oil filter

-

me Saturday, May 16, 2009 9:33:56 AM

Page 4

© 2005 Mitchell Repair Information Company, LLC.

2008 Honda Fit 2007-08 GENERAL INFORMATION Specifications - Fit

oil

Oil change without oil filter

Relief valve

Pump housing-to-outer rotor clearance Pump housing-to-rotor axial clearance Relief valve, oil pressure with oil temperature at 176°F (80°C)

-

0.02-0.14 mm (0.001 0.20 mm -0.006 in.) (0.008 in.) 0.10-0.18 mm (0.004- 0.20 mm 0.007 in.) (0.008 in.) 0.02-0.06 mm (0.001- 0.15 mm 0.002 in.) (0.006 in.)

Inner rotor-to-outer rotor clearance Oil pump

3.4 L (3.6 US qt)

At idle At 3,000 rpm

70 kPa (0.7 kgf/cm2 , 10 psi) min. 340 kPa (3.5 kgf/cm2 , 50 psi) min.

COOLING SYSTEM COOLING SYSTEM SPECIFICATIONS Item Measurement

Radiator

Coolant reservoir

Coolant capacities (Including engine, heater, hoses, and reservoir) Use Honda Long Life Antifreeze/Coolant Type 2

Qualification M/T: engine overhaul M/T: coolant change A/T: engine overhaul A/T: coolant change

Coolant capacity

5.4 L (1.43 US gal) 3.8 L (1.00 US gal) 5.3 L (1.40 US gal) 3.7 L (0.98 US gal) 0.4 L (0.11 US gal)

Radiator cap Opening pressure Thermostat

Standard or New

Begins to open Fully open

Opening temperature Valve lift at fully open

93-123 kPa (0.95-1.25 kgf/cm2 , 14-18 psi) 176-183°F (80 -84°C) 203°F (95°C) 8.0 mm (0.31 in.) min.

FUEL AND EMISSIONS FUEL AND EMISSIONS SPECIFICATIONS Item

Measurement

Qualification

Fuel pressure Pressure with fuel pressure gauge connected regulator Fuel tank

Capacity

Standard or New 320-370 kPa (3.3-3.8 kgf/cm2 , 47-54 psi) 41 L (10.8 US gal)

me Saturday, May 16, 2009 9:33:56 AM

Page 5

© 2005 Mitchell Repair Information Company, LLC.

2008 Honda Fit 2007-08 GENERAL INFORMATION Specifications - Fit

Engine idle (USA models)

Engine idle (Canada models)

Idle speed without load

M/T (in neutral), A/T (in N or P position)

750+50 rpm

Idle speed with high electrical load (A/C switch ON, temperature set to Max Cool, blower fan on High, rear window defogger ON, and headlights on high beam)

M/T (in neutral), A/T(in N or P position)

850 ± 50 rpm

Idle speed without load

M/T (in neutral). A/T (in N or P position)

850 ± 50 rpm

Idle speed with high electrical load (A/C switch ON, temperature set to Max Cool, blower fan on High, rear window defogger ON, and headlights on high beam)

M/T (in neutral), A/T(in Nor P position)

850 ± 50 rpm

CLUTCH CLUTCH SPECIFICATIONS item

Measurement

Qualification

Height from floor

163 mm (6.42 in.) 130-140 mm (5.125.51 in.) 6-20 mm (0.24-0.79 in.)

Stroke Clutch pedal

Play

Flywheel

Disengagement height from the floor Runout on clutch mating surface Rivet head depth

Clutch disc Thickness Pressure plate

Service Limit

Standard or New

Warpage Height of diaphragm spring fingers

Measure with feeler gauge and special tool

72 mm (2.83 in.)

-

0.05 mm (0.002 in.) max. 1.1-1.6 mm (0.0430.063 in.) 7.25-7.95 mm (0.285-0.313 in.) 0.03 mm (0.001 in.) max. 0.8 mm (0.03 in.) max.

0.15 mm (0.006 in.) 0.2 mm (0.08 in.) 5.0 mm (0.20 in.) 0.15 mm (0.006 in.) 1.0 mm (0.04 in.)

MANUAL TRANSMISSION AND M/T DIFFERENTIAL MANUAL TRANSMISSION AND M/T DIFFERENTIAL SPECIFICATIONS Item Manual

Measurement Capacity Use Honda MTF

Qualification Standard or New Fluid change

Service Limit

1.5L(1.6 US qt)

me Saturday, May 16, 2009 9:33:56 AM

Page 6

© 2005 Mitchell Repair Information Company, LLC.

2008 Honda Fit 2007-08 GENERAL INFORMATION Specifications - Fit

transmission fluid

Overhaul End play Diameter of ball bearing contact area (clutch housing side) Diameter of distance collar contact area

Mainshaft

Diameter of needle bearing contact area Diameter of ball bearing contact area (transmission housing side) Diameter of pilot bearing contact area Runout I.D. 3rd gear

Mainshaft 3rd and End play 4th gear

4th gear 3rd gear

Thickness 4th gear I.D. Mainshaft 5th gear

End play Thickness Diameter of needle bearing contact area (clutch housing side)

Countershaft

Diameter of ball bearing contact area (transmission housing side)

1.6L(1.7 US qt) 0.11-0.18 mm (0.004-0.007 in.) 25.9826.000 mm (1.0231-1.0236 in.) 28.992-29.005 mm (1.14141.1419 in.) 34.984-35.000 mm (1.37731.3780 in.) 25.977-25.990 mm (1.02271.0232 in.) 14.870-14.890 mm (0.58540.5862 in.) 0.02 mm (0.001 in.) max. 39.009-39.025 mm (1.53581.5364 in.) 0.06-0.21 mm (0.002-0.008 in.) 0.06-0.19 mm (0.002-0.007 in.) 27.92-27.97 mm (1.099-1.101 in.) 27.02-27.07 mm (1.064-1.066 in.) 39.009-39.025 mm (1.53581.5364 in.) 0.06-0.19 mm (0.002-0.007 in.) 28.92-28.97 mm (1.139-1.141 in.) 34.000-34.015 mm (1.33861.3392 in.) 24.980-24.993 mm (0.98350.9840 in.)

Adjust 25.93 mm (1.021 in.) 28.93 mm (1.139 in.) 34.93 mm (1.375 in.) 25.92 mm (1.021 in.) 0.05 mm (0.002 in.) 39.07 mm (1.538 in.) 0.33 mm (0.013 in.) 0.31 mm (0.012 in.) 27.85 mm (1.096 in.) 26.95 mm (1.061 in.) 39.07 mm (1.538 in.) 0.31 mm (0.012 in.) 28.85 mm (1.136 in.) 33.95 mm (1.337 in.) 24.93 mm (0.981 in.)

me Saturday, May 16, 2009 9:33:56 AM

Page 7

© 2005 Mitchell Repair Information Company, LLC.

2008 Honda Fit 2007-08 GENERAL INFORMATION Specifications - Fit

37.984-38.000 mm (1.49541.4961 in.) 0.02 mm (0.001 in.) max.

37.934 mm (1.493 in.) 0.05 mm (0.002 in.) 43.070 43.009-43.025 mm mm (1.6933(1.6957 1.6939 in.) in.) 0.03-0.12 mm 0.24 mm (0.001-0.005 in.) (0.009 in.) 26.89-26.94 mm 26.86 mm (1.059-1.061 in.) (1.057 in.) 45.009-45.025 45.07 mm mm (1.7720(1.774 in.) 1.7726 in.) 0.04-0.12 mm 0.24 mm (0.002-0.005 in.) (0.009 in.) 27.41-27.46 mm 27.36 mm (1.079-1.081 in.) (1.077 in.) 34.000-34.010 34.04 mm mm (1.3386(1.340 in.) 1.3390 in.) 39.989-40.000 39.93 mm mm (1.5744(1.572 in.) 1.5748 in.) 27.53-27.56 mm 27.51 mm (1.084-1.085 in.) (1.083 in.) 29.014-29.024 29.06 mm mm (1.1423(1.144 in.) 1.1427 in.) 34.989-35.000 34.93 mm mm (1.3775(1.375 in.) 1.3780 in.)

Diameter of 1st gear contact area Runout

I.D. Countershaft 1st gear

End play Thickness I.D.

Countershaft 2nd gear

End play Thickness I.D.

Countershaft 2nd gear distance collar

O.D. Length I.D.

Mainshaft 4th and O.D. 5th gear distance collar

A

51.97-52.03 mm (2.046-2.048 in.)

B

24.03-24.06 mm (0.946-0.947 in.)

Length Mainshaft MBS distance collar

26.02-26.17 mm (1.024-1.030 in.) 12.00-12.05 mm (0.472-0.474 in.)

I.D. Length

15.016-15.043 me Saturday, May 16, 2009 9:33:56 AM

Page 8

© 2005 Mitchell Repair Information Company, LLC.

2008 Honda Fit 2007-08 GENERAL INFORMATION Specifications - Fit

I.D. Reverse idler gear Gear-to-reverse gear shaft clearance Synchro ring

Ring-to-gear clearance

Finger thickness Shift fork Fork-to-synchro sleeve clearance Pawl groove width Reverse shift fork Fork-to-reverse idler gear clearance I.D. Shift arm

Shift fork diameter at contact area Shift arm-to-shift lever clearance

Select lever

Finger width Shaft-to-select lever clearance

Change lever

Groove (to select lever) Shaft-to-change arm clearance

M/T differential Backlash pinion gear M/T differential 80 80 mm shim-to-bearing outer race mm shim clearance in transmission housing

mm (0.591215.08 mm 0.5922 in.) (0.594 in.) 0.032-0.077 mm 0.14 mm (0.0012-0.0030 (0.006 in.) in.) Ring pushed 0.85-1.10 mm 0.4 mm against gear (0.033-0.043 in.) (0.02 in.) 1st-2nd and 3rd- 7.4-7.6 mm (0.294th forks 0.30 in.) 6.7-6.9 mm (0.265th fork 0.27 in.) 0.35-0.65 mm 1.0 mm (0.014-0.026 in.) (0.04 in.) 13.5-13.8 mm (0.531-0.543 in.) 1.30-1.90 mm 2.5 mm (0.051-0.075 in.) (0.098 in.) 13.973-14.000 mm (0.55010.5512 in.) 12.9-13.0 mm (0.508-0.512 in.) 0.2-0.5 mm 0.62 mm (0.008-0.020 in.) (0.024 in.) 12.80-12.95 mm (0.504-0.510 in.) 0.05-- 0.35 mm 0.55 mm (0.002-- 0.014 in.) (0.022 in.) 13.00-13.15 mm (0.512-0.518 in.) 0.013-0.070 mm 0.1 mm (0.0005-0.0028 (0.004 in.) in.) 0.05-0.15 mm (0.002-0.006 in.) 0-0.1 mm (0Adjust 0.004 in.)

AUTOMATIC TRANSMISSION AND A/T DIFFERENTIAL AUTOMATIC TRANSMISSION AND A/T DIFFERENTIAL SPECIFICATIONS Item Measurement Qualification Standard or New Service Limit Automatic transmission

Capacity Use Honda ATF-Z1

Fluid change

2.4 L (2.5 US qt)

me Saturday, May 16, 2009 9:33:56 AM

Page 9

© 2005 Mitchell Repair Information Company, LLC.

2008 Honda Fit 2007-08 GENERAL INFORMATION Specifications - Fit

fluid

Overhaul

6.0 L (6.3 US qt) 900-960 kPa (9.2- 850 kPa (8.7 At 2,000 rpm in P or Line pressure 9.8 kgf/cm2 , 130- kgf/cm2 , 120 N position 140 psi) psi) Sport and Fit At 2,000 rpm in 1st 890-970 kPa (9.1- 840 kPa (8.6 Sport gear in S position 1st clutch 9.9 kgf/cm2 , 130- kgf/cm2 , 120 pressure Except Sport At 2,000 rpm in 1 140 psi) psi) and Fit Sport position Sport and Fit At 2,000 rpm in 2nd 890-970 kPa (9.1- 840 kPa (8.6 Sport gear in S position 2nd clutch 9.9 kgf/cm2 , 130- kgf/cm2 , 120 pressure Except Sport At 2,000 rpm in 2 140 psi) psi) and Fit Sport position Pressure Sport and Fit At 2,000 rpm in 3rd 890-970 kPa (9.1- 840 kPa (8.6 Sport gear in S position 3rd clutch 9.9 kgf/cm2 , 130- kgf/cm2 , 120 pressure Except Sport At 2,000 rpm in 3rd 140 psi) psi) and Fit Sport gear in D3 position 890-970 kPa (9.1- 840 kPa (8.6 At 2,000 rpm in 4th 2 2 4th clutch pressure gear in D position 9.9 kgf/cm , 130- kgf/cm , 120 140 psi) psi) 890-970 kPa (9.1- 840 kPa (8.6 At 2,000 rpm in 5th 2 2 5th clutch pressure gear in D position 9.9 kgf/cm , 130- kgf/cm , 120 140 psi) psi) Stall speed Check with 2,450-2,750 Torque converter 2,600 rpm vehicle on level ground rpm 1.62-1.82 mm 1st (0.064-0.072 in.) 0.5-0.7 mm 2nd (0.020-0.028 in.) Clutch end plate-to-top-disc clearance 0.73-0.93 mm 3rd and 5th (0.029-0.037 in.) 0.7-0.9 mm (0.028-0.035 4th in.) 34.5 mm (1.36 1st 35.2 mm (1.39 in.) in.) Clutch return spring free 37.4 mm (1.47 2nd and 4th 39.5 mm (1.56 in.) length in.) 45.15 mm (1.778 43.0 mm (1.69 3rd and 5th in.) in.) 1.94 mm (0.076 1st, 3rd, and 5th in.) me Saturday, May 16, 2009 9:33:56 AM

Page 10

© 2005 Mitchell Repair Information Company, LLC.

2008 Honda Fit 2007-08 GENERAL INFORMATION Specifications - Fit

Clutch disc thickness

Clutch plate thickness

2nd and 4th

1.96 mm (0.077 in.)

1st and 4th

1.6 mm (0.063 in.)

2nd

2.3 mm (0.091 in.)

3rd and 5th

2.0 mm (0.079 in.)

Clutch waved-plate height 1st, 3rd, and 5th clutches

0.07-0.20 mm (0.003-0.008 in.) Mark 1

2.1 mm (0.083 in.)

Mark 2

2.2 mm (0.087 in.)

Mark 3

2.3 mm (0.091 in.)

Mark 4

2.4 mm (0.094 in.)

1st, 3rd, and 5th clutch endMark 5 plate thickness

2.5 mm (0.098 in.)

Mark 6

2.6 mm (0.102 in.)

Mark 7

2.7 mm (0.106 in.)

Mark 8

2.8 mm (0.110 in.)

Mark 9

2.9 mm (0.114 in.)

Mark AC or AM

2.1 mm (0.083 in.)

Mark AD or AN

2.2 mm (0.087 in.)

Mark AE or AP

2.3 mm (0.091 in.)

Mark AF or AQ 2nd and 4th clutch end-plate thickness Mark AG or AR

2.4 mm (0.094 in.)

Mark AH or AS

2.6 mm (0.102 in.)

Mark AJ or AT

2.7 mm (0.106 in.)

Mark AK or AU

2.8 mm (0.110 in.)

Clutch

2.5 mm (0.098 in.)

When discolored When discolored When discolored 0.05 mm (0.002 in.) When discolored When discolored When discolored When discolored When discolored When discolored When discolored When discolored When discolored When discolored When discolored When discolored When discolored When discolored When discolored When discolored When discolored

me Saturday, May 16, 2009 9:33:56 AM

Page 11

© 2005 Mitchell Repair Information Company, LLC.

2008 Honda Fit 2007-08 GENERAL INFORMATION Specifications - Fit

Mark AL or AV ATF pump thrust clearance

ATF pump

ATF pump gear-to-body clearance

Drive gear Driven gear

ATF pump driven gear I.D. ATF pump driven gear shaft O.D. Needle bearing contact I.D. Stator shaft

Torque converter side ATF pump side

Sealing ring contact area I.D. Reverse shift fork Park gear and pawl

Fork finger thickness

Shift fork shaft bore I.D. Servo body

Shift fork shaft valve bore I.D.

Regulator valve Sealing ring contact I.D. body At stator shaft Diameter of needle bearing contact area

At 5th gear collar At 3rd gear 5th gear

I.D. of gears 3rd gear 5th gear End play 3rd gear No. 1

When discolored 0.03-0.06 mm 0.07 mm (0.003 (0.001 -0.002 in.) in.) 0.210-0.265 mm (0.008-0.010 in.) 0.070-0.125 mm (0.003-0.005 in.) 14.016-14.034 mm When worn or (0.5518-0.5525 in.) damaged 13.980-13.990 mm When worn or (0.5504-0.5508 in.) damaged 27.000-27.021 mm When worn or (1.063-1.064 in.) damaged 29.000-29.021 mm (1.1417-1.1426 in.) 29.000-29.021 mm 29.05 mm (1.1417-1.1426 in.) (1.144 in.) 5.90-6.00 mm 5.40 mm (0.213 (0.232-0.236 in.) in.) When worn or damaged 14.000-14.010 mm When worn or (0.5512-0.5526 in.) damaged 37.000-37.039 mm 37.045 mm (1.4567-1.4582 in.) (1.4585 in.) 29.000-29.021 mm 29.05 mm (1.1417-1.1426 in.) (1.144 in.) 22.984-23.000 mm When worn or (0.9049-0.9055 in.) damaged 32.975-32.991 mm When worn or (1.2982-1.2989 in.) damaged 46.986-46.999 mm When worn or (1.8498-1.8503 in.) damaged 37.000-37.016 mm When worn or (1.4567-1.4573 in.) damaged 52.000-52.013 mm When worn or (2.0472-2.0478 in.) damaged 015-0.27 mm (0.006-0.106 in.) 0.04-0.10 mm (0.002-0.004 in.) 3.750 mm (0.1476 When worn or in.) damaged 2.9 mm (0.114 in.)

me Saturday, May 16, 2009 9:33:56 AM

Page 12

© 2005 Mitchell Repair Information Company, LLC.

2008 Honda Fit 2007-08 GENERAL INFORMATION Specifications - Fit

3.775 mm (0.1486 When worn or in.) damaged 3.800 mm (0.1496 When worn or No. 3 in.) damaged 3.825 mm (0.1506 When worn or No. 4 in.) damaged 3.850 mm (0.1516 When worn or No. 5 in.) damaged 3.875 mm (0.1526 When worn or No. 6 in.) damaged 40 x 63 mm thrust washer thickness 3.900 mm (0.1534 When worn or No. 7 in.) damaged 3.925 mm (0.1545 When worn or No. 8 in.) damaged 3.950 mm (0.1555 When worn or No. 9 in.) damaged 3.975 mm (0.1565 When worn or No. 10 in.) damaged 4.000 mm (0.1575 When worn or No. 11 in.) damaged 60.4-60.5 mm 5th gear collar length (2.380-2.381 in.) 5th gear collar flange 3.70-3.85 mm When worn or thickness (0.146-0.152 in.) damaged 1.91-1.97 mm 1.86 mm Sealing ring thickness (0.0752-0.0776 in.) (0.0732 in.) 2.025-2.060 mm 2.080 mm Width of sealing ring groove (0.0797-0.0811 in.) (0.0819 in.) 7.97-7.98 mm 7.95 mm (0.313 3rd clutch feed pipe O.D. (0.3138-0.3142 in.) in.) 8.000-8.015 mm 8.030 mm Feed pipe bushing I.D. (0.3150-0.3156 in.) (0.3161 in.) At torque converter 33.504-33.517 mm When worn or housing (1.3191-1.3196 in.) damaged Diameter of needle bearing 32.986-32.999 mm When worn or At 5th gear contact area (1.2987-1.2991 in.) damaged 35.983-35.999 mm When worn or Reverse selector hub (1.4167-1.4173 in.) damaged 39.000-39.016 mm When worn or 5th gear (1.5354-1.5361 in.) damaged I.D. of gears 42.000-42.016 mm When worn or Reverse gear (1.6535-1.6542 in.) damaged 0.04-0.27 mm 5th gear (0.002-0.011 in.) No. 2

Mainshaft

Countershaft

me Saturday, May 16, 2009 9:33:56 AM

Page 13

© 2005 Mitchell Repair Information Company, LLC.

2008 Honda Fit 2007-08 GENERAL INFORMATION Specifications - Fit

End play

Reverse gear

Reverse selector hub width Collar, 33.2 x 40 x 26 mm length Reverse selector hub O.D. 1st gear Diameter of needle bearing contact area

2nd gear 4th gear collar 1st gear

I.D. of gears

2nd gear 4th gear 1st gear

End play

2nd gear 4th gear No. 1 No. 2 No. 3 No. 4

31 x 54 mm thrust washer thickness

No. 5 No. 6 No. 7 No. 8 No. 9

0.10-0.25 mm (0.004-0.010 in.) 29.25-29.45 mm (1.152-1.160 in.) 25.95-26.00 mm (1.022-1.024 in.) 51.87-51.90 mm When worn or (2.042-2.043 in.) damaged 30.986-30.999 mm When worn or (1.2199-1.2204 in.) damaged 42.986-42.999 mm When worn or (1.6924-1.6929 in.) damaged 34.975-34.991 mm When worn or (1.3770-1.3776 in.) damaged 38.000-38.016 mm When worn or (1.4961-1.4967 in.) damaged 49.000-49.016 mm When worn or (1.9291-1.9298 in.) damaged 41.000-41.016 mm When worn or (1.6142-1.6148 in.) damaged 0.04-0.12 mm (0.002-0.005 in.) 0.04-0.12 mm (0.002-0.005 in.) 0.10-0.22 mm (0.004-0.009 in.) 3.925 mm (0.1545 When worn or in.) damaged 3.950 mm (0.1555 When worn or in.) damaged 3.975 mm (0.1565 When worn or in.) damaged 4.000 mm (0.1575 When worn or in.) damaged 4.025 mm (0.1585 When worn or in.) damaged 4.050 mm (0.1594 When worn or in.) damaged 4.075 mm (0.1604 When worn or in.) damaged 4.100 mm (0.1614 When worn or in.) damaged 4.125 mm (0.1624 When worn or in.) damaged

me Saturday, May 16, 2009 9:33:56 AM

Page 14

© 2005 Mitchell Repair Information Company, LLC.

2008 Honda Fit 2007-08 GENERAL INFORMATION Specifications - Fit

No. 10 No. 11 No. 12 No. 13 No. 14 No. 15 No. 16 No. 17 No. 1 No. 2 No. 3 No. 4 No. 5 No. 6 43 x 54.5 mm thrust washer No. 7 thickness No. 8 No. 9 No. 10 No. 11 No. 12 No. 13 4th gear collar length

4.150 mm (0.1634 in.) 4.175 mm (0.1644 in.) 4.200 mm (0.1654 in.) 4.225 mm (0.1663 in.) 4.250 mm (0.1673 in.) 4.275 mm (0.1683 in.) 4.300 mm (0.1693 in.) 4.325 mm (0.1703 in.) 2.900 mm (0.114 in.) 2.925 mm (0.115 in.) 2.950 mm (0.116 in.) 2.975 mm (0.117 in.) 3.000 mm (0.118 in.) 3.025 mm (0.119 in.) 3.050 mm (0.120 in.) 3.075 mm (0.121 in.) 3.100 mm (0.122 in.) 3.125 mm (0.123 in.) 3.150 mm (0.124 in.) 3.175 mm (0.125 in.) 3.200 mm (0.126 in.) 32.9-33.0 mm (1.295-1.299 in.)

When worn or damaged When worn or damaged When worn or damaged When worn or damaged When worn or damaged When worn or damaged When worn or damaged When worn or damaged When worn or damaged When worn or damaged When worn or damaged When worn or damaged When worn or damaged When worn or damaged When worn or damaged When worn or damaged When worn or damaged When worn or damaged When worn or damaged When worn or damaged When worn or damaged -

me Saturday, May 16, 2009 9:33:56 AM

Page 15

© 2005 Mitchell Repair Information Company, LLC.

2008 Honda Fit 2007-08 GENERAL INFORMATION Specifications - Fit

4th gear collar flange thickness Sealing ring thickness Width of sealing ring groove 2nd clutch Clutch feed pipe O.D. 4th clutch Clutch feed pipe bushing O.D.

Idler gear shaft

2nd clutch 4th clutch

ATF guide collar I.D. at sealing ring contact area End cover bearing contact area Cotters thickness Reverse idler gear shaft O.D. at needle bearing contact area I.D.

Reverse idler gear

I.D. of reverse idler gear shaft contact area on transmission housing I.D. of reverse idler gear shaft holder

3.75-3.90 mm When worn or (0.148-0.154 in.) damaged 1.87-1.97 mm 1.82 mm (0.072 (0.074-0.078 in.) in.) 2.025-2.060 mm 2.080 mm (0.0797-0.0811 in.) (0.0819 in.) 6.97-6.98 mm 6.95 mm (0.2744-0.2748 in.) (0.2736 in.) 11.47-11.48 mm 11.45 mm (0.4516-0.4520 in.) (0.4508 in.) 7.018-7.030 mm 7.045 mm (0.2763-0.2768 in.) (0.2774 in.) 11.500-11.518 mm 11.530 mm (0.4528-0.4553 in.) (0.4539 in.) 21.200-21.221 mm 21.25 mm (0.8346-0.8355 in.) (0.8366 in.) 30.003-30.013 mm When worn or (1,1812-1.1816 in.) damaged 1.39-1.42 mm (0.055-0.056 in.) 14.99-15.00 mm When worn or (0.590-0.591 in.) damaged 20.001-20.014 mm When worn or (0.7874-0.7880 in.) damaged 14.800-14.818 mm (0.5827-0.5834 in.) 14.800-14.824 mm When worn or (0.5827-0.5836 in.) damaged

AUTOMATIC TRANSMISSION AND A/T DIFFERENTIAL SPECIFICATIONS Standard or New Item

No. Free of Length Coil 9.9 mm 27.3 mm 0.8 mm (0.290 (1.074 8.0 (0.031 in.) in.) in.) 7.1 mm 23.7 mm 0.8 mm (0.280 (0.933 9.7 (0.031 in.) in.) in.) 7.1 mm 23.7 mm 0.8 mm (0.280 (0.933 9.7 (0.031 in.) in.) in.)

Measurement Qualification Wire Diameter Cut B valve spring Shift valve A spring Shift valve C spring

O.D.

me Saturday, May 16, 2009 9:33:56 AM

Page 16

© 2005 Mitchell Repair Information Company, LLC.

2008 Honda Fit 2007-08 GENERAL INFORMATION Specifications - Fit

Relief valve spring Lock-up control valve spring Main valve body spring (see MAIN VALVE BODY Cooler check DISASSEMBLY, INSPECTION, valve spring AND REASSEMBLY ) Shift valve D spring Servo control valve spring Stator reaction spring

Regulator valve spring A Regulator valve spring B Torque converter check valve spring

Regulator valve body spring(see REGULATOR VALVE BODY DISASSEMBLY, INSPECTION, Lock-up shift AND REASSEMBLY ) valve spring

1st accumulator spring B

1st accumulator spring A

4th accumulator spring Cut A valve

9.6 mm 1.0 mm (0.378 (0.039 in.) in.) 7.1 mm 0.6 mm (0.280 (0.024 in.) in.) 6.6 mm 0.85 mm (0.260 (0.033 in.) in.) 5.6 mm 0.8 mm (0.220 (0.031 in.) in.) 9.9 mm 0.8 mm (0.290 (0.031 in.) in.) 35.4 4.5 mm mm (0.177 in.) (1.394 in.) 14.7 1.9 mm mm (0.075 in.) (0.579 in.) 9.2 mm 1.6 mm (0.362 (0.063 in.) in.) 8.6 mm 1.2 mm (0.339 (0.047 in.) in.) 6.6 mm 1.0 mm (0.260 (0.039 in.) in.) 12.2 2.4 mm mm (0.094 in.) (0.480 in.) 18.6 2.4 mm mm (0.094 in.) (0.732 in.) 14.6 2.5 mm mm (0.098 in.) (0.575 in.) 0.9 mm

34.1 mm (1.343 in.) 29.6 mm (1.165 in.) 27.0 mm (1.063 in.) 28.1 mm (1.106 in.) 27.3 mm (1.075 in.)

10.2

11.2

11.3

15.9

8.0

30.3 mm (1.193 1.92 in.) 80.6 mm (3.173 16.1 in.) 44.0 mm (1.732 12.5 in.) 33.8 mm (1.331 12.2 in.) 35.5 mm (1.398 18.2 in.) 35.0 mm (1.378 7.7 in.) 50.1 mm (1.972 6.7 in.) 29.9 mm (1.177 4.9 in.)

9.9 mm 22.3 mm

me Saturday, May 16, 2009 9:33:56 AM

Page 17

© 2005 Mitchell Repair Information Company, LLC.

2008 Honda Fit 2007-08 GENERAL INFORMATION Specifications - Fit

spring Shift valve B spring 5th accumulator spring A

Servo body spring (see SERVO BODY DISASSEMBLY, INSPECTION, AND REASSEMBLY )

5th accumulator spring B

2nd accumulator spring A 2nd accumulator spring B 3rd accumulator spring A 3rd accumulator spring B

(0.035 in.) (0.390 in.) 7.1 mm 0.8 mm (0.280 (0.031 in.) in.) 16.6 2.5 mm mm (0.098 in.) (0.654 in.) 10.0 1.9 mm mm (0.075 in.) (0.394 in.) 14.6 1.8 mm mm (0.071 in.) (0.575 in.) 9.4 mm 1.85 mm (0.370 (0.073 in.) in.) 14.6 1.8 mm mm (0.071 in.) (0.575 in.) 9.4 mm 1.85 mm (0.370 (0.073 in.) in.)

AUTOMATIC TRANSMISSION AND A/T DIFFERENTIAL SPECIFICATIONS Item Measurement Qualification Standard or New Pinion shaft contact area 18.010-18.028 mm I.D. (0.7091-0.7098 in.) Carrier-to-pinion shaft 0.023-0.057 mm (0.0009clearance 0.0022 in.) A/T differential 26.025-26.045 mm Driveshaft contact area I.D. carrier (1.0246-1.0254 in.) Carrier-to-driveshaft 0.045-0.086 mm (0.0018clearance 0.0033 in.) Final driven gear backlash 0.085-0.142 mm (0.0033(reference) 0.0056 in.) 0.05-0.15 mm (0.002Backlash 0.006 in.) A/T differential 18.042-18.066 mm pinion gear I.D. (0.7103-0.7113 in.)

(0.878 6.9 in.) 23.7 mm (0.933 9.7 in.) 46.9 mm (1.846 7.8 in.) 38.5 mm (1.516 10.6 in.) 43.8 mm (1.724 7.9 in.) 32.5 mm (1.280 8.7 in.) 43.8 mm (1.724 7.9 in.) 32.5 mm (1.280 8.7 in.)

Service Limit 0.1 mm (0.004 in.) 0.12 mm (0.005 in.) 0.2 mm (0.008 in.) -

me Saturday, May 16, 2009 9:33:56 AM

Page 18

© 2005 Mitchell Repair Information Company, LLC.

2008 Honda Fit 2007-08 GENERAL INFORMATION Specifications - Fit

Pinion gear-to-pinion shaft clearance

0.055-0.095 mm (0.0022- 0.12 mm 0.0037 in.) (0.005 in.)

STEERING STEERING SPECIFICATIONS Item Measurement Qualification Standard or New Rotational play measured at outside edge with engine 0-10 mm (0-0.39 running in.) Steering wheel Starting load measured at outside edge with engine 34 N (3.5 kgf, 7.7 running lbf) Angle of rack guide screw loosened from locked Gearbox 7 ± 3° position SUSPENSION SUSPENSION SPECIFICATIONS Item

Measurement

Qualification

Front Rear Caster Front Front Total toe-in Rear Inward Front wheel turning angle equipped with Outward P175/65R14 81S tire (reference) Inward Front wheel turning angle equipped with Outward P195/55R15 84H tire (reference) Camber

Wheel alignment

Axial Steel wheel runout Radial Wheel Axial Aluminum wheel runout Radial Wheel bearing

End play

Front Rear

Standard or Service New Limit 0°00'±1° -1°30'±1° 3°45'±1° 0 ± 3 mm (0 ± 0.12 in.) 2.5 ± 2.5 mm (0.10 ± 0.10 in.) 38°00' ± 2° 32°00' 38°00'±2° 32°00' 0-1.0 mm (02.0 mm 0.04 in.) (0.08 in.) 0-1.0 mm (01.5 mm 0.04 in.) (0.06 in.) 0-0.7 mm (02.0 mm 0.03 in.) (0.08 in.) 0-0.7 mm (01.5 mm 0.03 in.) (0.06 in.) 0-0.05 mm (0-0.002 in.) 0-0.05 mm (0-0.002 in.)

BRAKES me Saturday, May 16, 2009 9:33:56 AM

Page 19

© 2005 Mitchell Repair Information Company, LLC.

2008 Honda Fit 2007-08 GENERAL INFORMATION Specifications - Fit

BRAKES SPECIFICATIONS Item Measurement Qualification Standard or New Service Limit Distance traveled when lever pulled with 6 to 8 clicks 196 N (20 kgf, 44 lbf) of force Parking 199.9-200 mm 201 mm (7.91 Drum I.D. brake (7.870-7.874 in.) in.) 2.0 mm (0.79 Shoe lining thickness 4.5 mm (0.18 in.) in.) M/T model 141 mm (5 9/16 in.) Pedal height (Carpet removed) Brake A/T model 145 mm (5 11/16 in.) pedal Free play 1-5 mm (0.04-0.20 in.) Master Piston-to-pushrod clearance 0-0.4 mm (0-0.02 in.) cylinder 19.0 mm (0.75 Thickness 21.0 mm (0.83 in.) in.) 0.10 mm Brake disc Runout (0.004 in.) 0.015 mm Parallelism (0.0006 in.) 9.5-10.2 mm (0.37- 1.6 mm (0.06 Brake pad Pad thickness 0.40 in.) in.) AIR CONDITIONING AIR CONDITIONING SPECIFICATIONS Item Measurement Qualification Standard or New Type HFC-134a(R-134a) Refrigerant Capacity of system 400-450 g (14.1-15.9 oz) SP-10 (P/N 38897-P13-003,38898-P13-003, Type 38899-P13-A01) Condenser 25 mL(5/6 fl.oz) Refrigerant Evaporator 35 mL(1 1/6 fl.oz) oil Capacity of components Each line and 10 mL(1/3 fl.oz) hose Compressor 80-90 mL (2 1/3-3 fl.oz) Field coil resistance At 68°F (20°C) 3.15-3.45 ohms Compressor Pulley-to-armature plate 0.35-0.65 mm (0.014-0.026 in.) clearance

DESIGN SPECIFICATIONS DESIGN SPECIFICATIONS Item Measurement

Qualification

Specification

me Saturday, May 16, 2009 9:33:56 AM

Page 20

© 2005 Mitchell Repair Information Company, LLC.

2008 Honda Fit 2007-08 GENERAL INFORMATION Specifications - Fit

DIMENSIONS

Overall length Overall width Overall height Wheelbase Track

WEIGHT

3.999 mm (157.4 in.) 1,682 mm (66.2 in.) 1,524 mm (60.0 in.) 2,450 mm (96.5 in.) 1,456 mm (57.3 in.) 1,451 mm (57.1 in.) five (5)

Front Rear

Seating capacity Gross Vehicle Weight Rating (GVWR)

1,563 kg (3,446 lbs) Water-cooled, 4--stroke SOHC VTEC engine

Type Cylinder arrangement Bore and stroke Displacement Compression ratio ENGINE

Inline 4--cylinder, transverse 73.0 x 89.4 mm (2.87 x 3.52 in.) 1,496 cm3 (91 cu in.) 10.4 Chain drive, SOHC VTEC 4 valves per cylinder Forced, wet sump, with trochoid pump

Valve train Lubrication system Oil pump displacement Water pump displacement

At 6,300 rpm

44.6 L (47.1 US qt)

At 6,000 rpm

120L (127 US qt) UNLEADED gasoline with 87 Pump Octane Number or higher Gear reduction 1.0 kW 30 seconds Clockwise as viewed from gear end Single plate dry, diaphragm spring

Fuel required

STARTER

CLUTCH

Type Normal output Hour rating Rotation direction Clutch type Clutch friction material surface area

143 cm2 (22.1 sq in.) Synchronized, 5--speed forward, 1 reverse Direct 1:1 3.461 1.869 1.321 0.969

Type Primary reduction MANUAL TRANSMISSION Gear ratio

1st 2nd 3rd 4th

me Saturday, May 16, 2009 9:33:56 AM

Page 21

© 2005 Mitchell Repair Information Company, LLC.

2008 Honda Fit 2007-08 GENERAL INFORMATION Specifications - Fit

Final reduction

5th Reverse Final Type

0.805 3.230 4.111 Single helical gear Electronically controlled automatic, five-speed forward, one reverse, threeelement torque converter with lockup clutch Direct 1:1 2.333 1.307 1.066 0.589 0.555 1.956 4.562 Single helical gear Rack and pinion with electrical power-assisted 12.80 2.41

Type Primary reduction AUTOMATIC TRANSMISSION Gear ratio

Final reduction

1st 2nd 3rd 4th 5th Reverse Final Type

Type STEERING

Overall ratio Turns, lock-to-lock Steering wheel diameter Type

370 mm (14.6 in.) Front Rear

SUSPENSION

Front Shock absorber Rear Size of front and rear tires

TIRES Size of spare tires Camber WHEEL ALIGNMENT

Caster Total toe-in

Except Sport Sport Except Sport and Fit Sport Sport and Fit Sport Front Rear Front Front Rear Front

Type of service

Independent strut with stabilizer, coil spring Torsion beam, coil spring Telescopic, hydraulic, nitrogen gasfilled Telescopic, hydraulic, nitrogen gasfilled P175/65R14 81S P195/55R15 84H T115/70D14 88M T125/70D14 93M 0°00'±1° - 1°30' ± 1' 3°45' ± 1 ° 0± 3 mm (0 ± 0.12 in.) 2.5 ± 2.5 mm (0.10 ± 0.10 in.) Power-assisted self-adjusting ventilated disc

me Saturday, May 16, 2009 9:33:56 AM

Page 22

© 2005 Mitchell Repair Information Company, LLC.

2008 Honda Fit 2007-08 GENERAL INFORMATION Specifications - Fit

brake

BRAKES

Type of parking brake Pad friction surface area Shoe friction surface area

Compressor

Condenser Evaporator AIR CONDITIONING

Blower

Power-assisted self-adjusting solid drum

Rear Mechanical actuating, rear wheels Front

44.0 cm2 (6.82 sq in.) x 2

Rear

67.2 cm2 (10.4 sq in.) x 2

Type Capacity Maximum speed Lubricant capacity Lubricant type Type Type Type Motor type Speed control Maximum capacity

Scroll 77.1 mL (4.7 cu in.)/rev. 12,000 rpm 80 mL(2 2/3 fl.oz) SP-10 Corrugated fin Corrugated fin Radial 165W/12V 4--speed

Temperature control

Air-mix type

Type Compressor clutch Electrical power consumption at 68°F (20°C) Type Refrigerant Capacity Battery

Fuses

ELECTRICAL RATINGS Light bulbs

380 m3 (13,400 cu ft)/h

Dry, single plate, Poly V-belt drive 42 W maximum at 12 V

HFC-134a(R-134a) 400-450 g (14.1-15.9 oz) 12 V-40 Ah/20 HR (12 V-32 Ah/5 HR) Under-hood fuse/relay 80 A, 60 A, 50 A, 40 A, 30 A, 20 A, box 15 A, 10 A Under-dash fuse/relay 30 A, 20 A, 15 A, 10 A, 7.5 A box Headlight high beam 12V-60W Headlight low beam 12V-55W Front side 12 V-5 W Amber color marker/parking lights Front turn signal lights 12 V-21 W Amber color Rear turn signal lights 12 V-21 W Amber color Brake/Taillights 12 V-21/5 W (two filaments) Rear side 12V-5W marker/taillights

me Saturday, May 16, 2009 9:33:56 AM

Page 23

© 2005 Mitchell Repair Information Company, LLC.

2008 Honda Fit 2007-08 GENERAL INFORMATION Specifications - Fit

Washer reservoir

High mount brake light Back-up lights License plate lights Ceiling light Cargo area lights Gauge lights Indicator lights Capacity (USA models) Capacity (Canada models)

12V-21 W 12V-21 W 12V-5W 12V-8W 12V-5W 12 V-LED (non-replaceable) 12V-LED, 14V-0.56 W, 0.84 W 2.5 L (2.6 US qt) 4.5 L (4.8 US qt)

BODY SPECIFICATIONS

Fig. 1: Body Specifications Courtesy of AMERICAN HONDA MOTOR CO., INC.

me Saturday, May 16, 2009 9:33:56 AM

Page 24

© 2005 Mitchell Repair Information Company, LLC.