The Heat Treat Doctor
r i al
Daniel H. Herring | 630-834-3017 | heattreatdoctor@industrialheating
[email protected] .com
•
H
•
T
H
H-Band and RH-Band Steels
W
hen and why do we use hardenability-band (H-band) and restricted-hardenability-band (RH-band) steels is a question often posed to The Doctor by design engineers. Why not use these steels all the time is a common question from heat treaters. Let’s learn more. The choice of material must be made only after careful consideration of the performance demanded by the application. For example, gears under load (Fig. 1) are subject to gradient stresses both on the active flank and at the root fillet. Proper material selection as well as heat treatment will produce strength gradients that are adequate to withstand these stresses and provide an acceptable margin of safety. Material choice must be a balance between overall cost and required service life. The Model of Gear Engineering (Fig. 2 online only) tells us that cost is the most important consideration among purchasers of raw material followed by material properties. From an engineering perspective, however, key design considerations require an analysis of the type of applied load, whether gradual or instantaneous, and the desired mechanical properties, such as bending fatigue strength or wear resistance. The required mechanical properties are the critical consideration and will define core strength and heat-treating requirements. Manufacturing economics plays an important role as well, and once again, cost manifested in reducing the number of manufacturing operations is paramount. In our gear example, each area in the gear-tooth profile sees different service demands. In the root area, good surface hardness and high residual compressive stress are desired to improve bending fatigue life. On the active flank, a combination of high hardness and adequate subsurface strength are necessary for adequate resistance to macropitting and sub-case fatigue. Proper material hardenability selection is critical to the success of any product since this affects how the material can be quenched (Fig. 3 online only). If the material hardenability is too high, the material will be costly, susceptible to quench cracking and produce high core hardness. For a given gear-tooth pitch size, for example, the result will be more distortion and higher midtooth core hardness than is necessary or desirable. If the material hardenability is too low, the material will exhibit low hardness with non-martensitic transformation products (NMTP) present in the microstructure, often exhibit uneven hardness and be prone to distortion and unpredictable size changes. For gears, the core
not too high to cause cracking at the case/core interface. Many manufacturers find that the use of tighter hardenability (RHband) steels ensures that the proper mid-tooth core hardness is consistently achieved. Restricted hardenability carburizing steels also make distortion more predictable from lot to lot (Fig. 4). This should not adversely affect cost or availability of the raw material due to the better steelmaking processes now being used by forging and bar-stock suppliers. New steelmaking processes are yielding more consistent hardenability, and some H-band steels actually meet RH-band requirements without the added cost. Another advantage to heat treaters is that RH-band grades simplify process control and avoid “tweaking” the cycle recipe each time a load is run. Finally, in medium carbon steels using an RH-band grade, surface hardness by induction hardening has been reported to be more achievable. H-band and RH-band steels incorporate slightly different carbon and possibly other chemistry ranges (Table 1) and hardenability (Table 2); generally have a broader chemistry range than standard alloy steels (to allow steel producers to design the optimum alloy combination); and have a more restricted hardenability range at each Jominy distance. In general, general, H-band steels offer a wide range of mechanical properties that depend on the development of tempered martensite after quenching and tempering. RH-band steels will exhibit a hardness range not greater than 5 HRC at the initial position (on the end-quench hardenability bar) and not greater than 65% of the hardness range for standard H-band steels in the “inflection” region. Generally, the RH-band follows the middle of the range corresponding to standard H-band.
Area of high fatigue stress due to high hertzian contact pressure (plus sliding) Fig. 1. Gear stress pattern
Area of high tooth bending load
r i al
H
•
•
T
H
Table 1. Comparison
of H-band and RH-band steel chemistries
%C
% Mn
% Si
%S
%P
%Ni
%Cr
%Mo
%Cu
%Fe
8620H
.17/.23
.60/.95
.15/.35
.25
.25
.35/.75
.35/.65
.15/.25
.35
balance
8620RH
.18/.23
.70/.90
.15/.35
.25
.25
.40/.70
.40/.60
.15/.25
.35
balance
Table 2. Comparison
of H-band and RH-band steel Jominy
J1
J4
J6
J8
8620H
41-48
27-41
21-34
N/A-30
8620RH
42-47
30-38
24-31
21-28
From a design standpoint, the depth to which parts are hardened not only affects their serviceability but also their cost. While the hardening need be no deeper than is required to provide the strength to sustain load at any given depth below the surface, service duty plays a critical role. For example, parts loaded principally in tension and parts operating at high hardness and high stress levels should be through-hardened. In contrast, the commercial practice, used for many parts including automotive, of hardening to 80% (or more) martensite at ¾ radius of the finished part is usually sufficient. For parts used in applications in which they are moderately stressed or are expected to see low deflection under load, less depth of hardening is required. Finally, the center of a 3.375-inch (85-mm) round of 4340H material can be austenitized and oil quenched to 80% martensite (46HRC). By contrast, when quenching to 95% martensite (55HRC), the bar size drops to a 2-inch (50-mm) round (Fig. 6).
Fig. 4. 8620RH clutch Fig. 5. 8822RH truck ring-and-pinion set pack for off-road vehicle transmission 70 60 99.9% Martensite (read left)
50 40
60
30 95% Martensite (read right)
50 40
Final Thoughts With the vast array of domestic and foreign steels available to choose from, with standard and non-standard chemistry, the challenge of selecting the right steel for a given application seems daunting. The use of H-band steels simplifies this task because direct comparisons can be made between the various steels to quantify their response to heat treatment. Different steels are often grouped by their hardenability requirements, allowing greater selectivity within a given design and making the job of the heat treater easier. RH-band steels provide even more confidence that, for example, core hardness within a specific range on a gear tooth can be achieved repeatedly, whereas an H-band steel might harden to the high end in one load and to the low end of the range in another load. IH References Republic Alloy Steels, 1961 Additional related information may be found by searching for these (and other) key words/terms via BNP Media SEARCH at www.industrialheating.com: hardenability, bending fatigue, wear resistance, martensitic transformation, core hardness, Jominy
s s e n d r a h C l l e w k c o R
60 50 90% Martensite (read left)
40 30
60
20
50 80% Martensite (read right)
40 30
60 50 40
50% Martensite (read left)
30 20 0.20
0.30
0.40 0.50 0.60 0.70 0.80 Percentage carbon Fig. 6. Hardness of martensite structures as a function of carbon content[1]
