Fittings for Plumbing and Heating

Stainless steel Carbon steel Copper

VSH

www.vsh-fittings.com

B

C

System handbook

Pr-EN-10-1.0

VSH Fittings The Netherlands

VSH Fittings B.V. P.O. box 498 1200 AL Hilversum The Netherlands Tel +31 (0)35 688 42 11 Fax +31 (0)35 688 43 79 [email protected]

Providing suitable solutions

Providing suitable solutions Providing suitable solutions

Contents

2

Disclaimer: The technical data are not binding and not expressly warranted characteristics of the goods. These are subject to change. Please consult our General Conditions of Supply. Additional information is available upon request. It is the Designer’s responsibility to select products suitable for the intended service and to ensure that pressure ratings and performance data is not exceeded. Always read and understand the installation instructions. Never remove any piping components nor correct or modify any piping deficiencies without first depressurizing and draining the system.

1 2 3 4 5 6

The XPress System Technical data 2.1 Areas of application 2.2 Tubes 2.3 Press fittings 2.4 Press tools 2.5 Installation guidelines 2.6 General application guidelines 2.7 Building-in 2.8 Corrosion Certificates Guarantee Combination pressings Product range 6.1 XPress stainless steel 6.2 XPress stainless steel GAS 6.3 XPress carbon steel 6.4 XPress copper 6.5 XPress copper GAS 6.6 XPress copper Solar 6.7 Tools

4 8 8 15 29 39 44 51 71 76 87 92 93 127 127 161 179 217 251 273 293

3

1

VSH Fittings VSH Fittings B.V. was founded in the early 1930s in Hilversum, the Netherlands. The activities of VSH Fittings B.V. cover the development, production and sales of water, heating and gas piping systems.

4

Over time the VSH product range has expanded as more and more fittings and accessories such as stop, gas and check valves were added to the range. Each time the deciding factor behind the product development of VSH was quality and ease of use for the installer. VSH can now offer you a complete range of brass compression, stainless, copper and carbon steel press fittings. The complete range of products is manufactured in Hilversum. We have established a good reputation through innovation, manufacturing of high quality products and a high level of service logistics. You can buy our products via wholesalers, sister companies which are part of Aalberts Industries and agencies. In the last few years VSH has developed more and more into a market oriented company. Customers’ wishes and needs are the starting point for the development and marketing of new products. VSH Fittings is part of the Aalberts Industries Group, Europe’s largest fittings manufacturer with production and sales of several of the most established products in the installations arena. VSH’s quality products have been recognised within the European market for many years now.

XPress System The advantages of the XPress System 1 The XPress System VSH Fittings continuously strives to be a leading force within the plumbing and heating industry and therefore provides the optimal level of support to installers throughout the industry. An excellent example of this is the XPress product range, which is comprised of three pipe systems: stainless steel press fittings and tubes, carbon steel press fittings and tubes (with and without a polypropylene coating) and copper press fittings. All these fittings are manufactured to incorporate the ‘M’ profile. XPress System products are manufactured using unique and modern machinery. A completely automated factory guarantees high quality and safe products. All welded products undergo a leak test which avoids any problems with installation procedures at a later date. The concept of the XPress system is to offer a complete solution to installers and with the added advantage of offering a greater level of flexibility overall. The XPress System consists of fittings, tools and tubes and under circumstances it is possible to utilise tubes from other manufacturers*. Furthermore the Xpress fittings can be used in conjunction with various brands of press tools**. The XPress System offers a comprehensive and high quality range of fittings, with the added benefit of an unusual level of flexibility when selecting material and tools. * see chapter 2.1 **see pages 40-44

Providing suitable solutions

5

1

6

Advantages of XPress • One of the most important advantages of the XPress System, is the connection of pipeline components without using a heat source. As a result of this there is no need for expensive insurance policies. The danger of fire damage is also excluded. • Compared with other “cold” connection techniques, the use of XPress dispenses the need for complicated clamping techniques, long preparation and drying times which all lead to longer installation times. • The quality of the connection is determined by the tool and not the operator. This guarantees constant quality and the connection can be visually checked. • The simple and fast connection technology and the short preparation time for the tube result in further cost

savings. As the connection is only realized with the use of press tools, the need to purchase and store other materials such as gases, adhesives, threading machines, etc. becomes superfluous. XPress pressfittings have the following technical advantages: • Excellent flow properties due to laser-welded fittings. • No chances of leakage due to a very accurate press profile (M-profile). • Easy tube insertion due to the tolerances on the fittings and O-rings. • Improved heat resistance due to the use of EPDM O-rings. The O-rings have a special coating which makes tube insertion easier reducing the danger of damaging the O-ring during tube insertion significantly.

Technical advantages: • The XPress System is a light weight solution. • XPress carbon steel tubes and fittings are protected against corrosion by a galvanized zinc layer, which is thermally applied (8-15 µm). • Xpress carbon steel tubes are protected on the inside against internal corrosion by a thermally applied oil film. • XPress stainless steel tubes are annealed for improved corrosion protection and high expansion capacity (flexibility).

Advantages of the improved M-profile: • The O-ring bead is pressed perpendicularly into the tube. This results in a seamless transition between fitting and tube which prevents dust or dirt from entering into the O-ring bead of the fitting.

• T  he bends have a radius of 1.2d which results in a more attractive and compact fitting which in turn increases the flexibility of installation. • To protect the tubes against entry of dirt, all Xpress tubes are supplied with coloured end caps. • All laser-welded and soldered fittings are 100% tested by an advanced vacuum leak test machine. • Adapters and reducers are made of just one part.

• T  he O-ring bead creates an extra mechanical connection between fitting and tube. • When pressed pressure is applied to the O-ring bead from three angles which results in an extremely secure connection and a strong deformation of the O-ring bead. • Due to the positioning of the O-ring at the beginning of the fitting the O-ring is highly visible to the installer. This results in a safer installation process as any damage or misplacement is immediately recognisable.

Providing suitable solutions

7

2 2 Technical data 2.1 XPress System areas of application Potable water installation XPress stainless steel fittings with stainless steel tubes which fullfill EN10312.

8

O-rings: Operating temperature: Operating pressure:

EPDM* (black) -35°C to +135°C (15-54 mm) -20°C to +110°C (76,1-108 mm) Max. 16 bar

XPress copper fittings with copper tubes which fulfill EN1057 R220/ 250/R290. O-rings: EPDM (black) Operating temperature: -20°C to +110°C Operating pressure: Max. 16 bar In potable water installations with XPress stainless steel fittings and tubes, the content of water-soluble chloride ions may not exceed 250 mg/l. Water heating installation XPress carbon steel fittings with zinc plated precision carbon steel tubes which fulfill EN10305-3 or XPress stainless steel fittings with stainless steel tubes which fulfill EN 10312. O-rings: Operating temperature: Operating pressure:

EPDM (black) -35°C to +135°C (12-54 mm) -20°C to +110°C (76,1-108 mm) Max. 16 bar

O-rings: EPDM (black) Operating temperature: -20°C to +110°C Operating pressure: Max. 16 bar Gas installation XPress stainless steel GAS fittings with stainless steel tubes approved according DVGW Worksheet VP614, SVGW Data sheet G1/01, and ÖVGW PG314. O-rings: HNBR** (yellow) Operating temperature: -20°C to +70°C Operating pressure: Max. 5 bar inside and outside Application: Inside (HTC***, proven tightness of the connection at 650°C for 30 min) or outside buildings. Above and under screed within buildings, no other corrosion protection is required. Outside of buildings, only lay above ground. Local regulations should always be observed. XPress copper GAS fittings with copper tubes approved according EN1057 R250/R290. O-rings: NBR**** (yellow) Operating temperature: -20ºC to +70ºC Operating pressure: Max. 5 bar Application: Inside (HTC 1 bar) or outside buildings (above ground 5 bar). Above and under screed within buildings, no other corrosion protection is required. Outside of buildings, only lay above ground. Local regulations should always be observed.

XPress copper fittings with copper tubes approved according EN 1057 R220/R250/R290. * Ethylene Propylene Dien Monomer

** Hydrogenated Nitrile Butadiene Rubber *** Higher Thermal Capacity ****Nitrile Butadiene Rubber

Providing suitable solutions

9

2.1 Note: R220 is not approved for GAS installations. For tools approved by VSH for gas installations, see table 18 and 19 on page 42. Cooling water installation XPress carbon steel fittings with zinc plated precision carbon steel tubes which fulfill EN10305-3 within closed systems or XPress stainless steel fittings with stainless tubes which fulfill EN10312 in closed and open systems.

10

O-rings: Operating temperature: Operating pressure:

EPDM (black) -35°C to +135°C (12-54 mm) -20°C to +110°C (76,1-108 mm) Max. 16 bar

XPress copper press fittings with copper tubes approved according EN1057 in closed and open systems. O-rings: EPDM (black) Operating temperature -20°C to +110°C Operating pressure: Max. 16 bar In cooling installations with stainless steel fittings and tubes, the content of water-soluble chloride ions may not exceed 250 mg/l. Sprinkler installation XPress carbon steel fittings with zinc plated precision XPress carbon steel Sendzimir tubes approved according among others VdS and FM or XPress stainless steel fittings with XPress stainless steel tubes approved according among others VdS and FM. O-rings: Operating temperature: Operating pressure:

EPDM (black) -35°C to +135°C (22-54 mm) -20°C to +110°C (76,1-108 mm) Max. 16 bar (pressures depending on application and dimensions)

*Viton® is a registered trade mark of DuPont Performance Elastomers

XPress Sprinkler is suitable for both wet and dry fixed sprinkler systems according to VdS and FM. For more information regarding XPress Sprinkler, please consult the “VSH XPress Sprinkler system” catalogue which is available on request or can be downloaded from our website www.vsh-fittings.com. Industrial installation XPress carbon steel fittings with zinc plated precision XPress carbon steel tubes which fulfill EN10305-3 or XPress stainless steel fittings with XPress stainless steel tubes which fulfill EN10312. O-rings: EPDM (black) Operating temperature: -35°C to +135°C (12-54 mm) -20°C to +110°C (76,1-108 mm) Tubes: Only VSH Operating pressure: Max. 25 bar (higher pressures available depending on application and dimensions) for carbon steel press fittings up to 54 mm and stainless steel press fittings up to 108 mm. Higher working pressures can be released due to different applicable safety factors which might apply in industrial applications. For pressures higher than 16 bar, tools and machines have to be in line with the prescribed tools for the XPress Sprinkler range which can be found in the “VSH XPress Sprinkler System” catalogue which is available on request or can be downloaded from our website www. vsh-fittings.com. For applications where another medium than water is transported such as oil, fuel, and aliphatic/aromatic hydrocarbons you should use the Viton©* (green) O-ring.

Providing suitable solutions

11

2.1 Solar installation XPress carbon steel fittings with zinc plated precision carbon steel tubes which fulfill EN10305-3 or XPress stainless steel fittings with stainless steel tubes which fulfill EN10312. O-rings: Operating temperature: Peak temperature: Operating pressure: Application: 12

Viton© (green) -30°C to +200°C 230°C (short term) Max. 16 bar Carbon steel only for closed systems installed inside buildings, stainless steel for both closed and return loop systems.

XPress copper fittings with copper tubes approved according EN 1057 R250/R290. O-rings: Viton© (green) Operating temperature: -30°C to +200°C Peak temperature: 230°C (short term) Operating pressure: Max. 10 bar Compressed air installation XPress carbon steel fittings with zinc plated precision carbon steel tubes which fulfill EN10305-3 or XPress stainless steel fittings with stainless steel tubes which fulfill EN10312. XPress carbon steel fittings with zinc plated carbon steel tubes can be used for compressed air if following conditions are observed: Water contents: max. 880 mg/m3, class 3, ISO 8573 part 1 Oil contents: max. 25 mg/m3, class 5, ISO 8573 part 1 When exceeding the maximum water content then copper or stainless steel should be used. For oil containing compressed air based on mineral or vegetable oil use Viton© O-rings. EPDM O-rings can only be used for syntetic oil or dry compressed air (not exceeding 25 mg/ m3).

O-rings: Operating temperature: Operating pressure:

EPDM (black) -35°C to +135°C (12-54 mm) -20°C to +110°C (76,1-108 mm) 12-54 mm max. 16 bar 76,-1 - 108 mm max. 10 bar

O-rings: Operating temperature: Peak temperature: Operating pressure:

Viton© (green) -30°C to +200°C 230°C (short term) 12-54 mm max. 16 bar 76,-1 - 108 mm max. 10 bar

Xpress copper fittings with copper tubes approved according EN 1057 R220/R250/R290. O-rings: EPDM (black) Operating temperature: -20°C to +110°C Operating pressure: Max. 10 bar O-rings: Operating temperature: Peak temperature: Operating pressure:

Viton© (green) -30°C to +200°C 230°C (short term) Max. 10 bar

On completion, compressed air pipeline systems must be properly tested. The system designer and installation contractor must ensure safe methods are selected for system testing which will comply with all current health and safety regulations. This may include testing compressed air lines with fluids or compressed air at a limited pressure, or a combination of both. In any event we do not recommend the maximum working pressure of the product to be exceeded during this procedure.

Providing suitable solutions

13

2.2 Since 30th May 2002 most pressure equipment and assemblies on the market have had to comply with the Pressure Equipment Directive (P.E.D.) 1999. The Directive concerns items such as vessels, pressurised storage containers, heat exchangers, steam generators, boilers, industrial piping, safety devices and pressure accessories. Please note that the P.E.D. applied on VSH XPress refers to article 3, sub. 3. This means that only sound engineering and a safe instruction for use and maintenance are required.

14

Steam installation XPress stainless press fittings with stainless steel tubes which fulfill EN10312. Viton© (grey) -20°C to +150°C 180°C (short term) Max. 5 bar

O-rings: Operating temperature: Peak temperature: Operating pressure:

High pressure dry fire main installation XPress stainless steel press fittings with XPress stainless steel tubes approved according by KIWA for pressures up to 40 bar. O-rings: Operating temperature: Dimensions: Operating pressure:

EPDM (black) -35°C to +135°C (22-35 mm) 22-35 mm (other dimensions available on request) Max. 40 bar

High pressure dry fire mains are an application where Oetiker couplings are combined with the XPress Sprinkler system as an alternative to standard dry fire mains. For more information regarding XPress Sprinkler, please consult the “VSH XPress Sprinkler system” catalogue which is available on request or can be downloaded from our website www.vsh-fittings.com.

2.2 Tubes 2.2.1 XPress Stainless steel tubes The XPress stainless steel tubes are thin-walled precision steel tubes. The outer and inner surfaces of the tubes are blank, free of discoloration and are supplied free of manufacturing residue that could otherwise cause corrosion. Entry of dirt during transportation or storage is prevented by caps at both ends of the tube and utilising the correct packaging for distribution. This chapter gives you all technical parameters, predominantly applying to construction technicalities of the XPress stainless steel tubes.

Heat insulation The following regulations apply to the insulation of potable water tubing systems: -C  old water lines should be protected against the occurrence of condensed water and overheating in accordance with DIN 1988, Part 2. For installations in the Netherlands the VEWIN work sheets should be followed. - Hot water lines should be insulated to prevent heat loss in accordance with the Energy Conservation Law (EnEG) and the Heating Installation Decree (HeizAnIV) (Germany). For installations in the Netherlands the VEWIN work sheets should be followed. The soluble chloride content in the insulation materials used should not exceed 0,05% by weight in accordance with DIN 1988, Part 7. Important: AS-quality insulation materials (compare also AGI Q 135) contain significantly less chlorides than the maximum allowable content.

Providing suitable solutions

15

2.2 Fire characteristics XPress stainless steel tubes are considered as incombustible tubes according to German class A building materials – DIN 4102 Part 1.

XPress stainless steel tube 1.4401 (AISI 316) The XPress stainless steel tube has been tested and approved for potable water installations by many international certification institutes for example also according to DVGW/DIN and DVGW – Worksheet GW 541. XPress stainless steel tubes have also been approved in gas installations inside buildings (with higher thermal capacity, proven over 30 min at 650°C and PN5) and outside buildings (without HTC) as above ground tube (not under screed or in ground). 16

Technical characteristics Material Specifications Approvals Type of tubing Welding deterioration reduction Weld slag removal Tolerances Finishing Surface finish Marking

Applications Installations always have to comply with local regulations. - All potable water installations in accordance with international drinking water institutes such as for example the German Potable Water Decree (TrinkwV) and EU council directive 98/83/EC, DIN 50930 Part 6 and in compliance with DIN 1988 - Water supply and rain water installations - Potable water for industrial applications - Wet and dry fire mains in accordance with DIN 1988 Part 6, VdS, FG, CNBOP, SBSC and FM - Conditioned water such as decalcinated/softened water, partly and completely desalinated water, distilled water, water with glycol - Compressed air, dry or oil containing - Conditioned installations for burnable gases: natural gases and liquid gases according to DVGW Worksheet G260 I/II. Installations of gas and liquid gas conducting tube installations according to DVGW - Worksheet G600, DVGW - TRGI 86/96 and TRF 1996

Smallest bending radius Supply mode Heat expansion coefficient Max. operating pressure

X5CrNiMo 17 12 2 Material no. 1.4401 according to DIN-EN 10088, PRE value >24 EN 10312 – DVGW worksheet GW541 (2004) Table 2 DVGW, SVGW, ETA, ÖVGW, BYGGFORSK, STF, PZH, SITAC, CSTBat, WRAS, VdS, FM, FG, CNBOP, SBSC TIG or laser welded under a protective atmosphere 100% EDDY CURRENT tested according to SEP 1914/ EN 10246-2 Inside and outside According to EN 10312 Annealed under a protective atmosphere W2R Matt silver coloured VSH XPress DN/size x wall thickness mm Edelstahl/ Stainless steel - Sanitär/Sanitary - GAS 1.4401 W2R, EN10217-7 EN10312 DVGW GW541 Reg.nr. DW-7301BM5610 SVGW ÖVGW W1.397 WRAS ETA BYGGFORSK STF PZH SITAC(+symbol) 0168/04 CSTBat(symbol) 116-1482, VdS G4080037 16.0 bar, Production date/Production code 3,5 x external diameter of the tube (max. 28 mm) Tubes, length of 6 m +0/-50 mm, with protective caps (green) 0,0160 mm/m with ∆T= 1K 16 bar

Table 1: Technical characteristics XPress stainless steel 1.4401 tube Nominal width Ø Outer diameter Ø Inner diame- Mass x s [mm] ter [mm] [kg/m] DN 12 DN 15 DN 20 DN 25 DN 32 DN 40 DN 50 DN 65 DN 80 DN 100

15 x 1,0 18 x 1,0 22 x 1,2 28 x 1,2 35 x 1,5 42 x 1,5 54 x 1,5 76,1 x 2,0 88,9 x 2,0 108 x 2,0

13,0 16,0 19,6 25,6 32,0 39,0 51,0 72,1 84,9 104,0

0,333 0,410 0,624 0,790 1,240 1,503 1,972 3,550 4,150 5,050

Tube capacity [l/m] 0,133 0,201 0,302 0,515 0,804 1,195 2,043 4,548 5,661 8,495

Table 2: Dimensions and weights XPress stainless steel 1.4401 tube Providing suitable solutions

17

2.2 XPress stainless steel tube 1.4521 (AISI 444) The 1.4521 XPress stainless steel tube has been tested and approved for potable water installations according to DVGW Worksheet GW 541, ETA, ÖVGW and SVGW.

Applications

18

- All potable water installations in accordance with the German Potable Water Decree (TrinkwV) and EU council directive 98/83/EC, DIN 50930 Part 6 and in compliance with DIN 1988 - Water supply and rain water installations - Potable water for industrial applications - Wet and dry fire mains in accordance with DIN 1988 Part 6 or FM - Conditioned water such as decalcinated/softened water, partly and completely desalinated water, distilled water, water with glycol - Compressed air, dry or oil containing

Max. operating pressure

16 bar

Table 3: Technical characteristics XPress stainless steel 1.4521 tube Nominal width Ø Outer diameter Ø Inner diame- Mass x s [mm] ter [mm] [kg/m] DN 12 DN 15 DN 20 DN 25 DN 32 DN 40 DN 50

15 x 1,0 18 x 1,0 22 x 1,2 28 x 1,2 35 x 1,5 42 x 1,5 54 x 1,5

13,0 16,0 19,6 25,6 32,0 39,0 51,0

0,333 0,410 0,624 0,790 1,240 1,503 1,972

Tube capacity [l/m] 0,133 0,201 0,302 0,515 0,804 1,195 2,043

Table 4: Dimensions and weights XPress stainless steel 1.4521 tube

XPress stainless steel tube 1.4520 (AISI 439) Technical characteristics Material Specifications Approvals Type of tubing Welding deterioration reduction Weld slag removal Tolerances Finishing Surface finish Marking

Smallest bending radius Supply mode Heat expansion coefficient

X2CrMoTi 18 2 Material no. 1.4521 according to DINEN 10088, PRE value >24 EN 10312 – DVGW worksheet GW541 (2004) Table 2 DVGW, SVGW, ETA, FM, ÖVGW Laser welded under a protective atmosphere 100% EDDY CURRENT tested according to SEP 1914/ EN 10246-2 Inside and outside According to EN 10312 Annealed under a protective atmosphere W2R Matt silver coloured VSH XPress DN/size x wall thickness mm Edelstahl/ Stainless steel, 1.4521, Sanitär/Sanitary - W2R EN10296-2 EN10312DVGW GW541 reg. nr. DW7301BP5610 SVGW ÖVGW ETA Production date/Production code 3,5 x external diameter of the tube (max. 28 mm)

The 1.4520 XPress stainless steel tube is an alternative for AISI 304 stainless steel tube with no nickel content, making it a cost effective alternative for applications where no potable water is being used. The tube has been tested and approved by FM for the use in dry and wet fixed sprinkler systems.

Applications - Compressed air, dry or oil containing - Solar installations - Cooling installations - Heating installations - Wet and dry fire mains in accordance with FM

Tubes, length of 6 m +0/-50 mm, with protective caps (light green) 0,0104 mm/m with ∆T= 1K

Providing suitable solutions

19

2.2 2.2.2 XPress carbon steel tubes

Technical characteristics Material Specifications Approvals Type of tubing Welding deterioration reduction Weld slag removal Tolerances Finishing Surface finish Marking

20

Smallest bending radius Supply mode Heat expansion coefficient Max. operating pressure

Material no. 1.4520 according to DIN-EN 10088-2 EN 10296-2 FM Laser welded 100% EDDY CURRENT tested according to SEP 1914/ EN 10246-2 Outside weld flat, insight raising max. 0,2 mm According to EN 10296-2 Annealed under a protective atmosphere Matt silver coloured VSH XPress DN/size x wall thickness mm Edelstahl/ Stainless steel, 1.4520 Heizung/Druckluft Chauffage/Air Comprimé - Heating/Compressed Air Production date/Production code 3,5 x external diameter of the tube (max. 28 mm) Tubes, length of 6 m +0/-50 mm, with protective caps (black) 0,0104 mm/m with ∆T= 1K 16 bar

Table 5: Technical characteristics XPress stainless steel 1.4520 tube

Nominal width Ø Outer diameter Ø Inner diame- Mass x s [mm] ter [mm] [kg/m] DN 12 DN 15 DN 20 DN 25 DN 32 DN 40 DN 50

15 x 1,0 18 x 1,0 22 x 1,2 28 x 1,2 35 x 1,5 42 x 1,5 54 x 1,5

13,0 16,0 19,6 25,6 32,0 39,0 51,0

0,333 0,410 0,624 0,790 1,240 1,503 1,972

Tube capacity [l/m] 0,133 0,201 0,302 0,515 0,804 1,195 2,043

Table 6: Dimensions and weights XPress stainless steel 1.4520 tube

XPress carbon steel tubes are thin-walled precision tubes. The XPress carbon steel tubes are protected against external corrosion by a coating of zinc-plating and passivating chrome. The zinc layer is applied thermally which results in a good adhesion between the zinc layer and the tubes. The XPress carbon steel tubes for sprinkler applications are made from cold rolled steel which is galvanized using the Sendzimir process. This chapter gives you all technical parameters, predominantly applying to construction technicalities, of the XPress carbon steel tubes. 21

Heat insulation The following regulations apply to the insulation of XPress carbon steel tubing systems: -C  old water lines should be protected against the occurrence of condensed water and overheating in accordance with DIN 1988, Part 2. - Hot water lines should be insulated to prevent heat loss in accordance with the Energy Conservation Law (EnEG) and the Heating Installation Decree (HeizAnIV) (Germany).

Fire characteristics XPress carbon steel tubes are considered as non-combustible tubes according to German class A building materials – DIN 4102 Part 1. XPress carbon steel tubes with polypropylene coating are considered as combustible tubes according to German class B2 building materials – DIN 4102 Part 1 i.e. burning without causing drops. Metallic tubes with a synthetic coating up to 2 mm are considered a non-flammable product in accordance with German building regulations.

Providing suitable solutions

2.2 XPress carbon steel precision tube XPress carbon steel tubes are thin-walled precision tubes manufactured in accordance with EN 10305-3 (previously DIN 2394/ NEN 1982) from a special kind of steel that has a very low carboncontent. The resulting product is very easy to bend. The absence of leaks is also checked, in accordance with EN 10246-1, so that all tubes will be guaranteed leak free.

Applications

22

- Closed loop heating installations according to DIN 4751 - Closed loop cooling installations with water/glycol mixture* - Compressed air, dry or oil containing - Solar applications (closed loop)

Nominal width Ø Outer diameter Ø Inner diame- Mass x s [mm] ter [mm] [kg/m] DN 10 DN 12 DN 15 DN 20 DN 25 DN 32 DN 40 DN 50 DN 65 DN 80 DN 100

10 x 1,2 15 x 1,2 18 x 1,2 22 x 1,5 28 x 1,5 35 x 1,5 42 x 1,5 54 x 1,5 76,1 x 2,0 88,9 x 2,0 108 x 2,0

7,6 12,6 15,6 19,0 25,0 32,0 39,0 51,0 72,1 84,9 104,0

Tube capacity [l/m]

0,271 0,420 0,494 0,761 0,980 1,241 1,542 1,999 3,503 4,412 5,382

0,045 0,125 0,191 0,284 0,491 0,804 1,195 2,043 4,083 5,661 8,495

Table 8: Dimensions and weight XPress carbon steel tube

Technical characteristics Material Specifications Approvals Type of tubing Welding detoriation reduction Weld slag removal Tolerances Finishing

Surface finish Marking Smallest bending radius Supply mode Heat expansion coefficient Max. operating pressure

Unalloyed ULC (ultra light carbon) Carbon steel, RSt 34-2 part No. 1.0034 according to EN 10305-3 EN 10305-3 (previously DIN 2394) CSTBat HF welded Tested according to EN 10246-1 or 100% EDDY CURRENT Outside weld flat, insight raising max. 0,5 mm According to EN10305-3 Zinc coating of at least 8-15μm. The tube welding seam is subsequently galvanized on the outside. Inside of the tube is protected by a thermally applied oil film Silver-coloured VSH XPress [dimension] galvanized, EN10305-3, [production date] 3,5 x external diameter of the tube (max. 28 mm)

,

Tubes, length of 6 m +0/-50 mm, with protective caps (red) 0,0108 mm/m with ∆T= 1K 16 bar

XPress carbon steel tubes with polypropylene coating XPress carbon steel tubes with polypropylene coating are used for the same applications and have the same technical characteristics as XPress carbon steel tubes (polypropylene coated tubes are marked “Galvanized - Polypropylene coated”) and are coated with a layer of polypropylene (PP) for protection against outer corrosion. The PP has a smooth surface and good resistance to tearing and impact. For a safe press fitting connection, it is essential to remove the polypropylene coating with a jacket stripping unit along the insertion depth. The rigidity of the press connection is only achieved by maintaining the insertion depth.

Technical characteristics Material Specifications Approvals Type of tubing

Unalloyed ULC (ultra light carbon) Carbon steel, RSt 34-2 part No. 1.0034 according to EN 10305-3 EN 10305-3 (previously DIN 2394) CSTBat HF welded

Table 7: Technical characteristics XPress carbon steel tube * Further additives for anti-freeze must be compatible with EPDM O-rings. Approval must be given by VSH in writing.

Providing suitable solutions

23

2.2 Welding detoriation reduction Weld slag removal Tolerances Finishing

Surface finish Marking Smallest bending radius Supply mode

24

Heat expansion coefficient Max. operating pressure Thermal load Heat conductivity

Tested according to EN 10246-1 or 100% EDDY CURRENT Outside weld flat, insight raising max. 0,5 mm According to EN10305-3 Zinc coating of at least 8-15μm. The tube welding seam is subsequently galvanized on the outside. Inside of the tube is protected by a thermally applied oil film High-heat stabilized polypropylene PP (B2) thickness ±1 mm, RAL 9001 VSH XPress [dimension] Galvanised- Polypropylene , [Production date] Coated, EN10305-3, 3,5 x external diameter of the tube (max. 28 mm) Tubes, length of 6 m +0/-50 mm, with protective caps (red) 0,0108 mm/m with ∆T= 1K 16 bar 120˚C permanent load 0,22 W/mK

Table 9: Technical characteristics XPress carbon steel tube with PP

The XPress carbon steel tubes with polypropylene coating are not to be confused with “white liaan” tube which is used in the Netherlands. White liaan tubes are welded steel thin-walled precision tubes manufactured in accordance with EN 10305-3 from St 34-2. The outside finishing is by a paint coating in white RAL9010. This tube is suitable to be used in press installations for the dimensions 15 x 1,5 and 22 x 1,5 where the fitting is pressed without removing the paint coating.

XPress Sprinkler carbon steel tubes The XPress Sprinkler carbon steel tubes for wet sprinkler systems are thin-walled precision steel tubes. The tubes are made from cold rolled steel that is galvanized using the Sendzimir process. During this process zinc is brought onto the metal strip, running through a zinc 25 bath, covering both sides simultaneously. The tube is protected both on the inside and outside with a zinc layer, with a minimum thickness of 20 μm. After welding the welding seam is zinc plated additionally. With the Sendzimir process a good adhesion of the zinc layer and corrosion resistance are achieved.

coating Nominal width DN 10 DN 12 DN 15 DN 20 DN 25 DN 32 DN 40 DN 50

Ø Outer diameter x s [mm] 12 x 1,2 15 x 1,2 18 x 1,2 22 x 1,5 28 x 1,5 35 x 1,5 42 x 1,5 54 x 1,5

Outer diameter incl. coating 14 17 20 24 30 37 44 56

Mass [kg/m] 0,338 0,434 0,536 0,824 1,052 1,320 1,620 2,098

Tube capacity [l/m] 0,072 0,125 0,191 0,284 0,491 0,804 1,195 2,043

Table 10: Dimensions and weights XPress carbon steel tube with PP coating

Applications - Wet fixed sprinkler installations in accordance with DIN 1988 part 6, VdS, FM, FG, SBSC and CNBOP.

Technical characteristics Material Specifications Approvals Type of tubing Welding detoriation reduction

Unalloyed ULC (’Ultra Light Carbon’) C-steel, E190 part no. 1.0031 according EN 10305-3 EN 10305-3 (previously DIN 2394) VdS, FM, FG, CNBOP HF welded Tested according to EN 10246-1 or 100% EDDY CURRENT

Providing suitable solutions

2.2 Weld slag removal Tolerances Finishing Surface finish Marking

Smallest bending radius Supply mode Heat expansion coefficient Max. operating pressure

26

Outside weld flat, insight raising max. 0,5 mm According to EN10305-3 Zinc coating of at least 20μm. The tube welding seam is subsequently galvanized on the outside. Silver-coloured VSH XPress Sprinkler Galvanized, DN/size x wall thickness mm, VdS, G4080007, 16.0 bar, batch number + production date 3,5 x external diameter of the tube (max. 28 mm) Tubes, length of 6 m +0/-50 mm, with protective caps (lilac) 0,0108 mm/m with ∆T= 1K 16 bar

Table 11: Technical characteristics XPress carbon steel sprinkler tube Nominal width Ø Outer diameter Ø Inner diame- Mass x s [mm] ter [mm] [kg/m] DN 20 DN 25 DN 32 DN 40 DN 50 DN 65 DN 80 DN 100

22 x 1,5 28 x 1,5 35 x 1,5 42 x 1,5 54 x 1,5 76,1 x 2,0 88,9 x 2,0 108 x 2,0

19,0 25,0 32,0 39,0 51,0 72,1 84,9 104,0

0,761 0,980 1,241 1,542 1,999 3,503 4,412 5,382

Tube capacity [l/m] 0,284 0,491 0,804 1,195 2,043 4,083 5,661 8,495

Table 12: Dimensions and weights XPress carbon steel sprinkler tube

2.2.3 Copper Tubing Copper tubes Copper tubes that may be used for the XPress copper system for water applications must comply with the norm EN 1057 R220/R250/ R290. Copper tubes that may be used for the XPress system for gas applications must comply with the norm EN 1057 R250/R290. EN 1057 is the norm for seamless copper and copper alloyed tubes for potable water-, gas- and heating installations. Distinction is made between soft, medium hard and hard alloy tubes indicated by R220, R250 and R290. The higher the figure, the harder the metal. The values refer to the tube’s tensile strength (220 N/mm2, 250 N/mm2 and 290 N/mm2).

Fire characteristics Uninsulated copper tubes certified according EN 1057/DVGW are considered as incombustible tubes according to German class A building materials – DIN 4102 Part 1.

Heat insulation For regulations on heat installation, please see the manufacturer’s guidelines. To avoid outside corrosion, please note when using insulating material that the materials contain no elements of ammonia or nitrate (page 86). In order to minimize the risk of outside corrosion, insulation material should as much as possible be used in conjunction with a moisture barrier. Materials such as Densopaste or a synthetic coating between the outside of the copper tube and insulation material are possibilities. For installations in the Netherlands the VEWIN work sheets should be followed.

Applications - All potable water installations in accordance with the German Potable Water Decree (TrinkwV) and EU guideline 98, DIN 50930 Part 6 and in compliance with DIN 1988. - Cold- and hot water installations Providing suitable solutions

27

2.3 - Water heating installations (pump-, warm water- and heating installations) - District heating installations - Solar installations* - Compressed air installations* - Cooling water/industrial water installations - Rainwater – utilization plants - Gas installations* - Heating oil EL (extra light) installations*

2.3 XPress fittings 2.3.1 Approvals Approval ARGB-KVGB ATG Advantica CSTBat CNBOP Cobrti DG DNV DVGW

Technical characteristics of approved copper tubes

28

Material Outer Ø tolerance Tensile strength

DHP copper part No. CW 024A to DIN EN 1412 EN 1057 R220 - soft - 220 N/mm2 (not for GAS) R250 - medium hard - 250 N/mm2 R290 - hard - 290 N/mm2 3,5 x outer diameter of tube (to -10°C)

Smallest bending radius

Copper tubes according to EN 1057 Outer

Wall thickness (mm)

12

R250

Ø (mm) 0,6

15

0,7

0,8

0,9

R250

18 22

R250

28

R250

35

1,0 R220 R220 R250 R290 R250 R290 R250 R290 R290

1,1

42

R290 R290

1,5

2,0

2,5

R220

R290

54

1,2

64 67 76,1

R250 R250 R290 R250 R290 R250 R290 R250 R290 R250 R290

Table 13: Copper tubes

22-108 mm 22-54 mm -

KIWA ÖVGW

-

PZH SBSC SINTEF SITAC SVGW

-

R290 R290 R290 R290 R290 R290 R250 R290

88,9 108

ÉMI ETA FG FM GASTEC GL

XPress carbon steel 12-108 mm 22-108 mm -

R290 R290

R250 R290

R290

VdS WRAS

22-108 mm -

XPress stainless steel 15-54 mm 15-108 mm 22-108 mm 15-108 mm for water 15-54 mm for gas 15-108 mm 22-108 mm 22-108 mm 15-54 mm 15-108 mm for water 15-54 mm for gas 15-108 mm 15-108 mm 15-108 mm 15-108 mm 15-108 mm for water 15-54 mm for gas 22-108 mm 15-108 mm

XPress copper 15-28 mm 12-108 mm 15-54 mm 12-108 mm 12-54 mm 15-28 mm 12-108 mm 12-108 mm for water 15-54 mm for gas 12-108 mm 12-54 mm 15-54 mm 12-108 mm GL industrial 15-54mm 12-54 mm 12-108 mm for water 15-54 mm for gas 12-108 mm 12-108 mm 12-108 mm for water 15-54 mm for gas 12-108 mm

For further details on copper tubes, please contact VSH.

Table 14: approvals * Special O-rings are required (see chapter 2.1).

Providing suitable solutions

29

2.3 XPress fittings are tested and approved for potable water installations, gas installations, sprinkler applications and many more applications. The current applicable approvals can be found in the above table.

XPress stainless steel GAS and copper GAS fittings in the dimensions 15-54 mm for gas installations must be pressed using Novopress pressing jaws/pressing slings. Approvals for other suppliers of press tools, jaws and slings such as Rems can be suitable for local approvals such as Gastec and KVGB.

2.3.2 Technical characteristics XPress stainless steel fittings are produced from material 1.4404 and fitted with an EPDM “Leak Before Pressed” (LBP) O-ring. XPress stainless steel fittings in sizes 15-54 are fitted with an EPDM “Leak Before Pressed” (LBP) O-ring (for more detailed information see page 36). Fittings in sizes 76,1 up to 108 are fitted with a standard EPDM O-ring. 30

XPress stainless steel GAS fittings are produced from material 1.4404 according to DIN 10088 and are fitted with a “yellow” HNBR O-ring. XPress carbon steel fittings are produced from steel RSt 34-2 and are protected against corrosion by a thermally applied zinc layer (8-15µm). XPress carbon steel fittings in sizes 12-54 are fitted with an EPDM “Leak Before Pressed” (LBP) O-ring (for more detailed information see page 36). Fittings in sizes 76,1 up to 108 are fitted with a standard EPDM O-ring. XPress copper fittings are produced from CU-DHP copper material CW 024 A and red bronze material 2.109 and fitted with an EPDM O-ring as standard. XPress copper GAS fittings are produced from CU-DHP copper material CW 024 A and red bronze material 2.109 and fitted with a “yellow“ NBR O-ring. XPress copper SOLAR fittings are produced from CU-DHP copper material CW 024 A and red bronze material 2.109 and fitted with a Viton© O-ring.

When using XPress stainless and carbon for sprinkler installations, please make sure to follow up the guidelines for installation and approved tools, which can be found in the “VSH XPress Sprinkler system” catalogue which is available on request or can be downloaded from our website www.vsh-fittings.com. Threaded fittings The XPress product range also includes components with inner- and outer threads for connection with other threaded parts of a tube network (e.g. valves, fittings). Inner- and outer threads are manufactured according to DIN 2999/ISO 7/1 for carbon and stainless steel fittings. Inner threads are manufactured according to BS 2779/ ISO 228/1 and outer threads are manufactured according to DIN 2999/ISO 7/1 for copper press fittings. Hemp or other sealants without chloride are suitable for the threads of stainless steel press fittings. Teflon thread sealing band may not be used in conjunction with stainless steel due to the water soluble chloride ions it contains. With threaded couplings, we recommend to carry out the sealing before the pressing, in order not to stress the press connection. Screw fittings (copper) The manufacturers of gas heating appliances supply their products with the respective screw connections in place. “Half screw fittings” type G6360 therefore can be used as press connections to these already present screw connections. As well as the screw fitting G6340 with double-sided press end, the half screw fitting (G6360) is also approved according to DIN 3436 HTC. Providing suitable solutions

31

2.3 Threaded transition fittings of red brass (gun metal) Threaded transition fittings are generally manufactured from red brass. Here, distinction is made between strand casting (straight part) and mould casting (bends, T-pieces and wall plates). Tests have shown that press fittings of mould castings (sand castings) are less suitable for gas installations for the following reasons: mould casting joints can never be as leakproof (homogenous) as with strand casting or copper. There is always a danger of cavities (air locks that occur when pouring) despite 100% impermeability testing. The mechanical load of the pressing heightens these dangers additionally as they can open the cavities. Therefore, for safety reasons, we have decided not to include any mould casting parts in copper gas press fittings. 32

XPress carbon steel press fittings Laser marking Red marking or Press Galvanized Approvals Dimension

XPress copper press fittings Marking RYW dimension KIWA DVGW

Marking of pressfittings XPress stainless steel press fittings Laser marking Press 316L Approvals Dimension

Packaging Label Type R..... Dimension Description: ...S-Pr EAN Nr. Art. Nr. VSH Approvals Number of pieces

XPress stainless steel GAS press fittings Marking Packaging Label Yellow marking Type R.....G GAS, GT5/PN5 Dimension 316L Description: ...S-Pr VSH EAN Nr. Dimension Art. Nr. VSH 316L Approvals DVGW Number of pieces

XPress copper GAS press fittings Marking Yellow marking GAS, GT1/PN5 RYW dimension DVGW Gastec Qa XPress copper Solar press fittings Marking Green marking RYW dimension KIWA DVGW

Packaging Label Type C..... Dimension Description: ...C-Pr EAN Nr. Art. Nr. VSH Approvals Number of pieces Packaging Label Type ..... Dimension EAN Nr. Art. Nr. VSH Approvals Number of pieces

Packaging Label Type G..... Dimension EAN Nr. Art. Nr. VSH Approvals Number of pieces

Packaging Label Type S..... Dimension EAN Nr. Art. Nr. VSH Approvals Number of pieces

Providing suitable solutions

33

2.3 Suitabillity of O-rings The standard fittings for water and the central heating are provided with EPDM O-rings. The type of O-ring which has to be used depends on the application and the medium. For this reason the gas press fittings are provided with (H)NBR O-rings. For special applications, such as oil-containing media or high temperatures, the Viton®/FPM O-ring has to be installed. Should you have the need for applications which are not mentioned in the table, always contact us to enquire whether the medium is suitable for use in combination with the type of press fitting you are using.

34

EPDM “leak before pressed” (LBP) - black Temperatures Applications With KTW recommendation. -35°C to +135°C For all installations for potable (12-54 mm) water and processed water, warm water tubes, circulation Peak 150°C tubes, fire fighting lines, etc. -35°C to +110°C (76,1-108 mm) Peak 130°C FPM Viton© “leak before pressed” (LBP) - green Temperatures Applications Installations for compressed -30°C to +200°C air, fuel oil, vegetable oil, fuels, Peak 230°C greases and industrial purposes, ozone-resistant (industry design) Not suitable for hot water applications

FPM Viton© “leak before pressed” - grey Temperatures Applications Steam installations -20°C to +150°C Peak: 180°C

HNBR - yellow Temperatures -20°C to +70°C

Applications Installations for burnable gases: Natural gases and liquid gases according to Worksheet DVGW-G 260 I/II. Installations for natural gas according to Worksheet DVGW -G600 TRGI 86/96, liquid gases according to TRF(1996)

NBR - yellow Temperatures -20°C to +70°C

Applications Installations for burnable gases: Natural gases and liquid gases according to Worksheet DVGWGas TRGI 86/89 Liquid gases according to TRF(1996)

XPress Leak Before Pressed function XPress carbon steel, XPress stainless steel and XPress copper are delivered with a Leak Before Pressed function (LBP). Fittings with a Leak Before Pressed function have the advantage that non pressed connections will leak water during pressure testing. This means an incomplete press connection is easily identified. As a result of this, the function of the LBP press fitting system gives an irrefutable result. Naturally, when mounted correctly, the press fittings will be water- and air tight when pressed. The LBP function on XPress carbon and stainless steel in the dimensions 12-54 mm is incooperated in the EPDM and Viton® FPM O-rings.

Providing suitable solutions

35

2.3 Working principle of the XPress LBP O-ring for carbon and stainless steel The design of the XPress LBP O-ring is based upon the creation of a leak path within the O-ring itself. This is made possible by adding material to the O-ring and not taking any material out. This results in an exceptionally strong O-ring without any weaknesses.

36

Advantages • Easy to recognize non pressed connections because of guaranteed water leakage during pressure test • Extra safety because leakage due to non pressing, (installation) mistakes are prevented • After pressing the fittings are guaranteed water and airtight • Extra material for leak function results in a strong O-ring

At strategic points small grooves have been created on the surface of the O-ring by adding additional material. This means there is a slight rise in the surface of the O-ring and therefore water will flow through these grooves when the fitting is not pressed. When the pressure is increased this will result in an escalation in the leakage. When pressed the O-ring is deformed and as a result the rubber from the raised surfaces fills the grooves. This creates a fully water- and air-tight connection.

XPress copper with LBP function The mechanical properties of copper differ from carbon steel and stainless steel. Copper is a softer material which makes it possible to create a LBP function in the material itself (O-ring bead) instead of the O-ring. The LBP function on the XPress copper is created by a triangle shaped O-ring bead which will leak before pressing. The function of this design is the same as the function of the LBP O-ring for carbon and stainless steel, which is to localize any forgotten pressings and prevent mistakes with installation procedures. Working principle of the XPress copper LBP fuction The triangle shaped O-ring bead will leave space between the tube and the fitting at 3 points in the O-ring bead. Through these gaps water will flow when the fitting is not pressed. The advantage with this design is that there is still enough contact between the tube and the O-ring which assures that the tube will stay in its place when inserted. When pressed the shape of the O-ring bead will change and becomes round again (due to the mechanical properties of copper it is very easy to reform the bead from a triangle shape to a perfect round shape Contact between again). After pressing this results in a water- and air-tight connection.

tube, O-ring and fitting which retain the tube.

Providing suitable solutions

37

2.4 2.3.3 Alternative applications for the fittings

2.4 Press tools

The choice of fittings and tubes depends on the assembly situation, the medium and the operating conditions. For approval of the use of XPress fittings for other applications such as water, compressed air and gas please contact your local agent or VSH. Always make sure that installations comply with local regulations.

Press tools consist of a press machine and the corresponding press jaws- or slings. The press machine can be either battery- or electrically powered. Figure 1 shows a battery powered version. For each tube diameter used, the respective press jaws- and slings should be used for a perfect tight connection. Figure 3 shows a section of the press profile before and after pressing. All XPress fittings with a diameter from 12 mm to 108 mm can be pressed using the suitable press machines listed in the product range. Figure 1: ACO 202 The respective jaws or slings with M-profile should be used according to the diameter that has to be installed. For diameters of 35 to 108 mm’s there is a possibility, that in addition to the press sling, a special adaptor may also be required.

2.3.4 Electrical heat tracing

38

XPress stainless steel, carbon steel and copper may be used in conjunction with electrical heat tracing. In the case of XPress stainless steel, electrical heat tracing may be used if the inside of the tube is guaranteed not to permanently exceed 60°C. For thermal disinfection for example, short-term temperatures (max. 1 hour a day) of 70°C are permitted. Due to impermissible pressure increase as a result of heating in sealed tubes it is not allowed to heat sealed off tubes.

2.3.5 Equipotential bonding in houses All metallic pipework systems using equipotential bonding must comply with equipotential bonding requirements. After all plumbing has been completed, always ensure continuity checks are conducted by a qualified electrician in accordance with the regulations. XPress stainless steel and blank copper tubes according to EN 1057/R250-R290 in combination with the respective fittings are electrical conductive tube systems and therefore must be included in the equipotential bonding. XPress carbon steel with and without polypropylene coating is not an electrical conductive system and does not need to be included in the equipotential bonding.

Note: GAS press fittings may only be pressed with the press jaws/ slings stated in the certificate and the table. This also applies for sprinkler installations. VSH guarantees an excellent press connection, provided the tools are used correctly. The tools permitted by VSH may be found listed in the document “XPress tool schedule“, which is also available on our internet site at products > Before pressing press fittings > tool schedule. Our website can be found under the following address: www.vsh-fittings.com

After pressing

Figure 2: Pressing before and after Providing suitable solutions

39

2.4 2.4.1 Press tools approved for XPress stainless steel and XPress carbon steel In the below tables you can find the list of approved press tools. The most actual list of tools permitted by VSH can be found listed in the document “XPress tool schedule“, which is available on our internet site www.vsh-fittings.com at products > press fittings > tool schedule.

40

Dimension

Manufacturer Press machine

Press jaws/slings

12-54 mm

Ridgid

RP 10-S (230 V) RP 300 (230 V) RP 300-B (12 V) RP 10-B (12 V)

Ridgid jaws are not allowed Machines are only allowed with other brands of jaws/slings approved by VSH Fittings

12-54 mm

Viega

PT2-EH (230 V) PT3-EH (230 V) PT3-AH (12 V) Pressgun 4E (18 V) Pressgun 4B (230 V) Type 5A Type 5

Viega jaws are not allowed Machines are only allowed with other brands of jaws/slings approved by VSH Fittings

Nussbaum

Dimension

Manufacturer Press machine

Press jaws/slings

12-28 mm

Comap

12-28 mm

Novopress

Presskid (12 V) AFP 101 (9,6 V)

Presskid jaws 12-28 mm (inlay) AFP 101 jaws 12-28 mm

Sudopress 1932 (9,6 V) Sudopress 2432 (12 V)

Sudopress basic jaws with press inlays (12-28 mm) with following RYW or COMAP IX

12-54 mm

Comap

Sudopress 3263 (14,4 V)

12-54 mm

Novopress

ECO 1 Pressboy (230 V) ECO 201/202 (230 V) ACO 1 Pressboy (12 V) ACO 3 Pressmax (12 V) ACO 201 (12 V) ACO 202 (18 V) EFP 2 (230 V) EFP 201/202 (230 V) AFP 201/202 (14 V)

Jaws 12-54 mm Slings and adapter (ZB201/203) 35-54 mm

Sudopress basic jaws with press inlays (12-28 mm) with following RYW or COMAP IX Novopress press jaws for 12-35 mm and Novopress slings and adapter for 42-54 mm

ECO 3 Pressmax (230 V) ECO 301 (230V)

Jaws 12-54 mm Slings and adapter (ZB302) 35-54 mm Press slings 76,1-108 mm For press slings 76,1 & 88,9 one adapter is needed (ZB321) For press sling 108 two adapters are needed (ZB 321 & ZB322) Important: Fitting size 108mm must be pressed in 2 stages!

12-108 mm

Novopress

Slings and adapter for ACO 3 are compatible with (ZB302)

Table 15: Press tools approved for XPress carbon and stainless steel

2.4.2 Press tools approved for XPress copper (solar) Dimension

Manufacturer Press machine

Press jaws/slings

12-28 mm

Novopress

Presskid (12 V) AFP 101 (9,6 V)

Presskid jaws 12-28 mm (inlay) AFP 101 jaws 12-28 mm

12-54 mm

Novopress

ECO 1 Pressboy (230 V) ECO 201/202 (230 V) EFP 2 (230 V) ACO 1 Pressboy (12 V) ACO 3 Pressmax (12 V) ACO 201 (12 V) ACO 202 (18 V) EFP 201/202 (230 V) AFP 201/202 (230 V)

Jaws 12-35 mm Slings and adapter (ZB201/203) 42-54 mm Slings and adapter for ACO 3 are compatible with (ZB302)

12-108 mm

Novopress

ECO 3 Pressmax (230 V) ECO 301 (230V)

Jaws 12-35 mm Slings and adapter (ZB301) 42-54 mm Press slings 64-108 mm. For Press slings 64-88,9 mm one adapter is needed (ZB321). For Press sling 108 two adapters are needed (ZB 321 & ZB322) Important: Fitting size 108 mm must be pressed in 2 stages! Press slings are marked especially for copper.

12-28 mm

Klauke

MAP1 ‘Klauke Mini’ (9,6 V) MAP2L ‘Klauke Mini‘ (18 V)

Klauke mini jaws 12-28 mm (28 mm jaw is marked with VSH only)

12-54 mm

Klauke

UAP2 (12 V) UNP2 (230 V) UP75 (12 V) UAP3L (18 V)

Jaws 12-35 mm Important: 42-54 mm only with (M-profile)Novopress slings

12-28 mm

Rothenberger

Romax Compact (12 V)

Romax compact mini jaws 12-28 mm

12-54 mm

Rothenberger

Romax Pressliner 12 V Jaws 12-35 mm Romax Pressliner ECO 12 V Only new type of jaws with red dot and polished Romax AC ECO 230 V press profile Important: 42-54 mm only with (M-profile) Novopress slings

12-54 mm

Ridgid

RP 10-S (230 V) RP 300 (230 V) RP 300-B (12 V) RP 10-B (12 V)

Slings 76,1-108 mm

76,1-108 mm

Novopress

Hydraulic-Press-System HCP / HA 5 ACO401 (18 V)

12-28 mm

Klauke

MAP1 ‘Klauke Mini’ (9,6 V) Klauke mini jaws 12-28 mm (28 mm jaw is marked MAP2L ‘Klauke Mini‘ (18 V) with VSH only)

12-54 mm

Klauke

UAP2 (12 V) UNP2 (230 V) UP75 (12 V) UAP3L (18 V)

Jaws 12-54 mm Slings and adapter 42-54 mm Important: Both new Klauke M-slings (without press inlays) as well as old Klauke M-slings (with press inlays) can be used

12-108 mm

Klauke

UAP4 (12V) UAP4L (18 V)

Jaws 12-54 mm Slings and adapter 42-54 mm Slings and adapter 76,1-108 mm

ACO401 to be used with HP401 slings

76,1-108 mm

Klauke

UAP100 (12 V) UAP100L (18 V)

Slings 76,1-108 mm

12-28 mm

Rems

Mini Press ACC (12 V)

Rems mini press jaws 12-28 mm*

12-54 mm

Rems

Powerpress 2000 S401 (230 V) Powerpress E (230 V) Powerpress ACC (230 V) Accu-Press S403 (12 V) Accu-Press ACC (12 V)

Jaws 12-54 mm* Slings and adapter 42-54 mm

12-28 mm

Rothenberger

Romax Compact (12 V)

Romax Compact mini jaws 12 -28 mm

12-54 mm

Rothenberger

Romax-Pressliner (12 V) Romax-Pressliner ECO (12 V) Romax AC Eco (230 V)

Jaws 12-35 mm: Only new type of jaws with red dot and polished press profile. Jaws 42-54 mm: Only new jaws with a circle around the dimension.

12-54 mm

Virax

Viper P20 (14,4 V) Viper P21 (18 V)

Jaws 12-54 mm

Ridgid jaws are not allowed. Machines are only allowed with other brands of jaws approved by VSH Fittings. Important: 42-54 mm only with (M-profile) Novopress slings

Table 16: Pressing of copper from Ø42 mm only with (M-profile) Novopress slings * 18 and 28 only allowed with marking from “108” (Q1 2008) or higher

Providing suitable solutions

41

2.4 2.4.3 Press tools approved for XPress stainless steel GAS Dimension

42

Manufacturer Press machine

2.4.5 Press tools approved for XPress Sprinkler

Press jaws/slings

Dimension

Manufacturer Press machine

Press jaws/slings

15-28 mm

Novopress

Presskid (12 V) AFP 101 (9,6 V)

Presskid jaws 15-28 mm AFP Mini jaws 15-28 mm

22-35 mm

Novopress

ECOTEC Jaws 22-28 mm Slings and adapter (ZB201/203) 35 mm

15-54 mm

Novopress

ECO 1 Pressboy (230 V) ECO 201/202 (230 V) EFP 2 (230 V) ACO 1 Pressboy (12 V) ACO 3 Pressmax (12 V) ACO 201 (12 V) ACO 202 (18 V) EFP 201/202 (230 V) AFP 201/202 (230 V)

Jaws 15-35 mm Slings and adapter (ZB201/203) 42-54 mm

15-54 mm

Klauke

UAP2 (12 V) UNP2 (230 V) UP75 (12 V)

Important: Only with Novopress jaws & slings

15-54 mm

Rems

Powerpress 2000 S401 (230 V) Powerpress E (230 V) Powerpress ACC (230 V) Accu-Press S403 (12 V) Accu-Press ACC (12 V)

Important: Only with Novopress jaws & slings

15-54 mm

Virax

Viper P20 (14,4 V) Viper P21 (18 V)

Important: Only with Novopress jaws & slings

15-28 mm

Rothenberger

Romax Compact (12 V)

Important: Only with Novopress jaws & slings

15-54 mm

Rothenberger

Romax-Pressliner (12 V) Romax-Pressliner ECO (12 V) Romax AC Eco (230 V)

Important: Only with Novopress jaws & slings

ECO 201/202 (230 V) ACO 201 (14,4 V) ACO 202 (18 V) EFP 2 (230 V) EFP 201/202 (230 V) AFP 201/202 (14,4 V) ECO 301 (230V)

For ECO 301: ECO 301 jaw 22-28 mm Slings and adapter (ZB302) 35 mm

42-54 mm

Novopress

ECO 301 (230 V)

Power slings and adapter (ZB302) 42-54 mm

76,1-108 mm

Novopress

ACO401 (18 V)

Slings HP401 76,1-108 mm

76,1-108 mm

Klauke

UAP100 (12 V)

Slings KSP3 76,1-108 mm

Table 19: from Ø35 mm press jaws are not allowed

2.4.6 Maintenance and correct usage of press tools

Table 17: from Ø42 mm press jaws are not allowed

Correct pressing with the XPress systems will be guaranteed when the press tools stated in the tables 15-19 are used correctly. Regular maintenance and lubrication of the press jaws, slings and tools is necessary. Please observe the manufacturer‘s instructions for use and maintenance.

2.4.4 Press tools approved for XPress copper GAS Dimension

Manufacturer Press machine

Press jaws/slings

15-28 mm

Novopress

Presskid (12 V) AFP 101 (9,6 V)

Presskid jaws 15-28 mm AFP Mini jaws 15-28 mm

15-54 mm

Novopress

ECO 1 Pressboy (230 V) ECO 201/202 (230 V) EFP 2 (230 V) ACO 1 Pressboy (12 V) ACO 3 Pressmax (12 V) ACO 201 (12 V) ACO 202 (18V) EFP 201/202 (230 V) AFP 201/202 (230 V)

Jaws 15-35 mm Slings and adapter (ZB201/203) 42-54 mm

15-28 mm

Novopress

Presskid (12 V) AFP 101 (9,6 V)

Presskid jaws 15-28 mm AFP Mini jaws 15-28 mm

15-54 mm

Novopress

ECO 1 Pressboy (230 V) ECO 201 (230 V) EFP 2 (230 V) ACO 1 Pressboy (12 V) ACO 3 Pressmax (12 V) ACO 201 (12 V) EFP 201 (230 V) AFP 201 (230 V)

Jaws 15-35 mm Slings and adapter (ZB201/203) 42-54 mm

15-54 mm

Klauke

UAP2 (12 V) UNP2 (230 V) UP75 (12 V)

Important: Only with Novopress jaws & slings

12-28 mm

Rems

Mini Press ACC (12 V)

Rems mini press jaws 12-28 mm*

15-54 mm

Rems

Powerpress 2000 S401 (230 V) Powerpress E (230 V) Powerpress ACC (230 V) Accu-Press S403 (12 V) Accu-Press ACC (12 V)

Jaws 15-35 mm

When jointing XPress copper & XPress copper GAS fittings in sizes above 35 mm, it is essential that the grooves in the press jaw/sling are lubricated with Dri-slide lubricant! The jaws/slings should be lubricated in this way after every 50 joints for sizes 42 mm to 76 mm and after every 5 joints for size 108 mm. Care should be taken to avoid contact between lubricant and ‘O-rings.’ Badly maintained and/or damaged pressjaws are a potential risk. Damaged jaws can damage the fittings, leaving metal particles behind in the jaw as a result. If the same jaw is then used to press a stainless steel fitting, these metal particles will be pressed into the fitting, which could lead to pitting and further corrosion. Therefore always make sure to properly clean your press jaws and slings when switching between materials. Other press tools not mentioned in the chapters 2.4.1 up to 2.4.5 can be approved on request.

Important: 42-54 mm only with (M-profile) Rems or Novopress slings

Table 18: from Ø42 mm press jaws are not allowed

Providing suitable solutions

43

2.5 2.5 Installation guidelines

2.5.3 Calibration

2.5.1 Cut the tube to length

Always ensure the tube ends are radial and even rounded. Especially with white copper tubes according to DIN EN 1057/R220 (1mm), e.g. Wicu tubes, the tube ends must be calibrated before pressing.

After measuring, the tubes can be cut to length using a tube cutter (see fig. 4), a fine-toothed handsaw or a mechanical saw with electrical motor suitable for the tube material. The tube should always be cut completely. Never partially cut the tube and break it off as this could cause corrosion.

44

Do not use oil cooled saws, abrasive wheels or flame cutting

Figure 4: Cutting the tube

XPress carbon steel tubes with polypropylene coating and coated copper tubes (Wicu) To ensure a safe connection of the press­fitting, it is essential to remove the tube’s synthetic coat up to the insertion depth before assembling the press fitting using a jacket stripping unit. With Wicu tubes the rigidity of the press connection is only achieved by maintaining the insertion depth and by using an insert stiffener.

2.5.4 Marking insertion depth The necessary insertion depth (see table 21) must be marked on the tube or the press fitting (the latter for fittings with tube ends) in order to guarantee a safe and proper joint. Mark the insertion depth with a suitable insertion depth marker as supplied by VSH. Reliable pressing with the corresponding Figure 6: Marking the depth 45 tensile strengths can only be achieved by a proper installation. The pressing operation behind the bead is of crucial importance for the tensile strength. The marking on the tube must remain visible (but close to the fitting) after the connection is pressed to identify any movement before or after pressing.

2.5.6 Check the fitting and tube 2.5.2 Deburring the tube The tube ends must be carefully deburred inside and out after being cut to length. This is in order to avoid damage to the O-ring when inserting the tube into the pressfitting. Deburring the inside of tubes prevents pitting and corrosion. Deburring in- and outside can either be carried out using a hand deburrer suitable for the material or an electrical tube deburrer. Burrs Figure 5: Deburring the tube sticking to the tube must be removed.

Before assembly, the fitting must be checked Figure 7: Check fitting/tube to ensure the correct position and presence of the O-rings. The tube, fitting and O-ring should be examined for foreign material (e.g. dirt, burrs), which should be removed if present.

2.5.7 Assembly of fitting and tube Insert the tube into the press fitting up to the marked insertion depth while being rotated Figure 8: Assembly fitting/tube slightly and pushed in an axial direction at the same time. Providing suitable solutions

2.5 The marking for the insertion depth must still be visible. In case of fittings without a stop the fittings should be inserted at least as far as the marked insertion depth. Rough and careless insertion of the tube into the press fitting may result in damage to the O-ring and is therefore not permitted. When assembly is more difficult due to permitted tolerances in sizes, a lubricant as water or soap may be used. Under no circumstances may oils, fats or grease be used as lubricants.

46

To optimise the installation time, it is normal practice to assemble a number of connections first and, then press the various tube connections one after the other. Marking the distance (A) provides a check that the tube has not been pushed out of the fitting during the pressing process. Before starting the final pressing process of the various tube connections, it is also important to check some of the minimum required work space distances (see table 20).

Table 21 shown below gives the minimum required working space so that the pressing of the fittings can be carried out correctly using the appropriate press tools. These distances relate to the general installation configurations that are schematically depicted in figures 9-11.

Outer-Ø

a

12 15 18 22 28 35 42 54 64 67 76,1 88,9 108

XPress copper (GAS) 17 20 20 21 23 26 30 35 50 50 50 64 64

Minimum distance dmin (mm) XPress stainless steel (GAS) carbon steel, copper 10 10 10 10 10 10 20 20 30 30 55 65 80

Minimum tube length 2xA + dmin (mm) XPress XPress XPress stainless carbon copper steel steel (GAS) (GAS) 44 44 44 50 50 50 50 50 50 52 52 52 56 56 56 62 62 62 80 80 80 90 90 90 130 130 165 165 140 186 186 193 234 234 208

Fig. 11 b

c

d

tube depth 40 mm

56

20

75

25

28

131

60

20

75

25

28

131

40 mm

22 mm

65

25

80

31

35

150

40 mm

Figure 8

A (mm) XPress XPress stainless carbon steel steel (GAS) 17 17 20 20 20 20 21 21 23 23 26 26 30 30 35 35 55 55 63 63 77 77

a

18 mm

A

Insertion depth

Fig. 10 b

12-15 mm

d min

Ø [mm]

Fig. 9

28 mm

75

25

80

31

35

150

60 mm

35 mm

75

30

80

31

44

170

70 mm

42 mm

140/115*

60/75* 140/115*

60/75*

75

265

70 mm

54 mm

140/120*

60/85* 140/120*

60/85*

85

290

70 mm 70 mm

64 mm

145*

110*

145*

100*

100

345

67 mm

145*

110*

145*

100*

100

345

70 mm

76,1 mm

140*

110*

165*

115*

115

395

80 mm

88,9 mm

150*

120*

185*

125*

125

435

90 mm

108 mm

170*

140*

200*

135*

135

470

100 mm * Slings

Table 21: Space needed for installation

≥ 40 mm

da

a

b

Figure 9

c b

Figure 10

Figure 11

Table 20: Minimum distances between pressings Providing suitable solutions

47

2.5 2.5.8 Pressing

48

Before starting to press, the press jaws and slings must be checked for dirt, which must be removed if present. Furthermore, it must be ensured that the press machine is in good condition and that the instructions for operating the device, maintenance and the manufacturers’ instructions have been followed. Also make sure that you use the correct press jaws and slings for the application and that these are corresponding to the fittings which are used. In order to create a proper pressed connection, the groove of the press tool must enclose the press fitting O-ring bead. Once the pressing has started, always complete the press cycle and under no circumstances interrupt the process. The approved machines, press jaws and press slings are shown on pages 40 - 43 or can be found listed in the document “XPress tool schedule“, which is available on our internet site www.vsh-fittings.com at products > press fittings > tool schedule.

Local regulations should always be observed. Note: 1. Gas tubes and fittings should be marked yellow to avoid confusion. 2. Tubes are to be protected against mechanical damage when mounted above screed. 3. Carry out tests according to G1 Gas Guidelines (e.g. check covered tubes). 4. When mounted under screed (above the reinforcement) place in concrete slots.

2.5.9 Bending It may be necessary to bend a tube in order to carry out the installation. Normal hand-, hydraulic or electrically-operated bending tools with the corresponding bending formers of tools can be used for this. The manufacturer will determine the suitability of the bending tool. XPress stainless steel, carbon steel tubes and copper tubes according to DIN EN 1057 are cold pliable.

Pressing gas installations XPress stainless steel GAS and XPress copper GAS are suitable for gases of the second and the third gas family (natural- and liquid gases) according to DVGW Worksheet G 260 and are installed within buildings (with HTC) and outside buildings (without HTC) as above.

The tube may not be bent when warm due to the danger of corrosion.

A mixture of XPress stainless steel GAS and XPress copper GAS is not permitted for new installations. Connections to gas fittings and gas parts of brass, red bronze, ductile grey cast iron and aluminium diecasting can be installed with gas threads/press fittings or flanges. In case of repairs, make sure the tubes correspond with the DIN-EN/ DVGW standards, have a perfect and undamaged outer surface and have not been painted.

Stainless steel tube (15-28 mm)

rmin = 3,5 x d

Copper tubes (12-54 mm) according to EN 1057 and DVGW-GW 392

rmin = 3,5 x d

Carbon steel tubes (12-28 mm)

rmin = 3,5 x d

The minimum bend radius is as follows:

A smaller bend radius is not permitted.

Providing suitable solutions

49

2.6 2.6 General application guidelines

2.5.10 Mixed metal system XPress stainless steel fittings and tubes can easily be combined with controls and fittings of stainless steel and non-ferrous metals. Connection with galvanized carbon steel or less noble fittings or components can lead to contact corrosion. This can be prevented using synthetic or non-ferrous metal fittings or spacers of at least 50 mm long (DIN 1988, part 7). For more information on corrosion, see 2.8, page 76. Table 22 shows the possible mix combinations. XPress Fittings copper

red bronze/ brass

carbon steel

stainless steel

allowed

allowed

allowed

allowed allowed

2.6.1 Heat expansion compensation The level of thermal expansion within tubing systems depends on the type of materials used. This linear expansion needs to be taken into account during the installation. This can be done by allowing for sufficient expansion space. Small length changes can be accommodated by an adequate space for expansion as well as by the elastic properties of the tubing system itself. Larger length changes require compensation by other means; e.g. installation of expansion compensation devices or placement of clips and saddles.

System

XPress Tube

50

copper tube

closed open

allowed

allowed

not allowed

carbon steel

closed

allowed

allowed

allowed

allowed

not allowed

not allowed

not allowed

not allowed

closed

allowed

allowed

allowed

allowed

open

allowed

allowed

not allowed

allowed

open stainless steel

Table 23: XPress fittings and tube combinations

51

Expansion compensators which can be used are by pipe leg (figure 12), U-bend (figure 14) or compensators. The compensation size can be determined beforehand by calculating the length changes. The equation to calculate the length changes is as follows:

We recommend using red bronze or brass fittings for the transition from copper to steel. Combinations should be avoided in the case of gas installations (see 2.5.8 “Pressing gas installations”).

∆l = l x α x ∆T

∆l = overall linear expansion in [mm] l = length of the trajectory in question [m] ∆T = temperature difference [°C] α = linear expansion coefficient, which is: for stainless 1.4401 tubing α = 0,0160 mm/m for stainless 1.4521/1.4520 tubing α = 0,0104 mm/m for carbon steel tubing α = 0,0108 mm/m for copper tubing α = 0,0170 mm/m

Providing suitable solutions

2.6 Tables 23a, 23b, 23c and 23d show the expansion of the various pipelines depending on the length of the tube and the rise in temperature. Calculation of the expansion compensation length In case of greater expansion, expansion compensators or, in complicated cases Ω-shaped compensating loops will need to be fitted and calculated. The formula with which the expansion equalizer in mm is calculated is as follows:

52

Bd = k x √(de x ∆l) Bd = expansion compensation length k = material constant = 45 for XPress stainless and carbon steel tube = 35 for copper tube de = outside diameter of the tube [mm] Δl = linear expansion that needs to be compensated [mm]

∆T [K] l [m] 10 20

30

40

50

60

80

90

1

0,16

0,32

0,48

0,64

0,80

0,96

70 1,12

1,28

1,44

100 1,60

2

0,32

0,64

0,96

1,28

1,60

1,92

2,24

2,56

2,88

3,20

3

0,48

0,96

1,44

1,92

2,40

2,88

3,36

3,84

4,32

4,80

4

0,64

1,28

1,92

2,56

3,20

3,84

4,48

5,12

5,76

6,40

5

0,80

1,60

2,40

3,20

4,00

4,80

5,60

6,40

7,20

8,00

6

0,96

1,92

2,88

3,84

4,80

5,76

6,72

7,68

8,64

9,60

7

1,12

2,24

3,36

4,48

5,60

6,72

7,84

8,96

10,08

11,20

8

1,28

2,56

3,84

5,12

6,40

7,68

8,96

10,24

11,52

12,80

9

1,44

2,88

4,32

5,76

7,20

8,64

10,08

11,52

12,96

14,40

10

1,60

3,20

4,80

6,40

8,00

9,60

11,20

12,80

14,40

16,00

12

1,92

3,84

5,76

7,68

9,60

11,52

13,44

15,36

17,28

19,20

14

2,24

4,48

6,72

8,96

11,20

13,44

15,68

17,92

20,16

22,40

16

2,56

5,12

7,68

10,24

12,80

15,36

17,92

20,48

23,04

25,60

18

2,88

5,76

8,64

11,52

14,40

17,28

20,16

23,04

25,92

28,80

20

3,20

6,40

9,60

12,80

16,00

19,20

22,40

25,60

28,80

32,00

Table 23a: Overall linear expansion Δl [mm]. Only for XPress stainless steel 1.4401

Providing suitable solutions

53

2.6 ∆T [K] l [m] 10 20

54

100

∆T [K] l [m] 10 20

30

40

50

60

70

80

90

30

40

50

60

70

80

90

1

0,10

0,21

0,31

0,42

0,52

0,62

0,73

0,83

0,94

1,04

1

0,11

0,22

0,32

0,43

0,54

0,65

0,76

0,86

0,97

100

2

0,21

0,42

0,62

0,83

1,04

1,25

1,46

1,66

1,87

2,08

2

0,22

0,43

0,65

0,86

1,08

1,30

1,51

1,73

1,94

2,16

3

0,31

0,62

0,94

1,25

1,56

1,87

2,18

2,50

2,81

3,12

3

0,32

0,65

0,97

1,30

1,62

1,94

2,27

2,59

2,92

3,24

4

0,42

0,83

1,25

1,66

2,08

2,50

2,91

3,33

3,74

4,16

4

0,43

0,86

1,30

1,73

2,16

2,59

3,02

3,46

3,89

4,32

5

0,52

1,04

1,56

2,08

2,60

3,12

3,64

4,16

4,68

5,20

5

0,54

1,08

1,62

2,16

2,70

3,24

3,78

4,32

4,86

5,40

6

0,62

1,25

1,87

2,50

3,12

3,74

4,37

4,99

5,62

6,24

6

0,65

1,30

1,94

2,59

3,24

3,89

4,54

5,18

5,83

6,48

1,08

7

0,73

1,46

2,18

2,91

3,64

4,37

5,10

5,82

6,55

7,28

7

0,76

1,51

2,27

3,02

3,78

4,54

5,29

6,05

6,80

7,56

8

0,83

1,66

2,50

3,33

4,16

4,99

5,82

6,66

7,49

8,32

8

0,86

1,73

2,59

3,46

4,32

5,18

6,05

6,91

7,78

8,64

9

0,94

1,87

2,81

3,74

4,68

5,62

6,55

7,49

8,42

9,36

9

0,97

1,94

2,92

3,89

4,86

5,83

6,80

7,78

8,75

9,72

10

1,04

2,08

3,12

4,16

5,20

6,24

7,28

8,32

9,36

10,40

10

1,08

2,16

3,24

4,32

5,40

6,48

7,56

8,64

9,72

10,80

12

1,25

2,50

3,74

4,99

6,24

7,49

8,74

9,98

11,23

12,48

12

1,30

2,59

3,89

5,18

6,48

7,78

9,07

10,37

11,66

12,96

14

1,46

2,91

4,37

5,82

7,28

8,74

10,19

11,65

13,10

14,56

14

1,51

3,02

4,54

6,05

7,56

9,07

10,58

12,10

13,61

15,12

16

1,66

3,33

4,99

6,66

8,32

9,98

11,65

13,31

14,98

16,64

16

1,73

3,46

5,18

6,91

8,64

10,37

12,10

13,82

15,55

17,28

18

1,87

3,74

5,62

7,49

9,36

11,23

13,10

14,98

16,85

18,72

18

1,94

3,89

5,83

7,78

9,72

11,66

13,61

15,55

17,50

19,44

20

2,08

4,16

6,24

8,32

10,40

12,48

14,56

16,64

18,72

20,80

20

2,16

4,32

6,48

8,64

10,80

12,96

15,12

17,28

19,44

21,60

Table 23b: Overall linear expansion Δl [mm]. Only for XPress stainless

Table 23c: Overall linear expansion Δl [mm]. Only for XPress carbon

steel 1.4520/1.4521

steel

Providing suitable solutions

55

2.6

56

Bd

40

50

60

70

80

90

100

1

0,17

0,34

0,51

0,68

0,85

1,02

1,19

1,36

1,53

1,70

2

0,34

0,68

1,02

1,36

1,70

2,04

2,38

2,72

3,06

3,40

3

0,51

1,02

1,53

2,04

2,55

3,06

3,57

4,08

4,59

5,10

4

0,68

1,36

2,04

2,72

3,40

4,08

4,76

5,44

6,12

6,80

5

0,85

1,70

2,55

3,40

4,25

5,10

5,95

6,80

7,65

8,50

6

1,02

2,04

3,06

4,08

5,10

6,12

7,14

8,16

9,18

10,20

7

1,19

2,38

3,57

4,76

5,95

7,14

8,33

9,52

10,71

11,90

8

1,36

2,72

4,08

5,44

6,80

8,16

9,52

10,88

12,24

13,60 15,30

9

1,53

3,06

4,59

6,12

7,65

9,18

10,71

12,24

13,77

10

1,70

3,40

5,10

6,80

8,50

10,20

11,90

13,60

15,30

17,00

12

2,04

4,08

6,12

8,16

10,20

12,24

14,28

16,32

18,36

20,40 23,80

14

2,38

4,76

7,14

9,52

11,90

14,28

16,66

19,04

21,42

16

2,72

5,44

8,16

10,88

13,60

16,32

19,04

21,76

24,48

27,20

18

3,06

6,12

9,18

12,24

15,30

18,36

21,42

24,48

27,54

30,60

20

3,40

6,80 10,20

13,60

17,00

20,40

23,80

27,20

30,60

34,00

Table 23d: Overall linear expansion Δl [mm]. Only for copper

L 2

L

30

L 2

Bd

Lb 2

L

∆T [K] l [m] 10 20

Lb

L

Figure 12

Figure 13

Figure 14

57

830

Graph 1: Nomogram (for XPress stainless steel) for calculating the situation Figs. 12 and 13. Expansion Bd [mm]

Providing suitable solutions

2.6 Without the requirement for the mathematical calculation, we would get the same result through interpolation of the data in table 20. With the expansion for the respective section of the pipeline, we need to calculate the length of the expansion compensator required for its compensation – see figures 12 and 13. Using the nomogram in graph 1, we get ca. 830 mm. The analytical calculation shows: Bd = 45 x √(22 x 15,36) = 827,2 mm

460

58 Graph 2: Nomogram for calculating the Situation Fig. 14 Expansion

In case of an Ω-shaped expansion connection, the calculated value of the expansion equalizer also visible from figure 14 is to be halved as it is actually two expansion sections. The value [Bd] is not exactly divided by two, but should be divided by a factor of 1,8: Lb = (45/1,8) x √(22 x 15,36) = 459,6 mm or otherwise: Lb = Bd /1,8 = 827,2/1,8 = 459,6 mm

compensator Lb [mm]

Graph 2 shows a value for Lb of ca. 460 mm. The Nomogram in graph 1 enables the fast and accurate establishment of the expansion bend length [Bd] considering the respective tube types and the expansion to be compensated [Δl]. Graph 2 shows the values [Lb] for the installation situation illustrated in figure 14. The following is an example of an analytical calculation: A tube network with a length of 16 m consisting of stainless steel tubing with a diameter of 22 mm subject to a temperature difference of 60 K. When using the equation for calculating the expansion, the result is: ∆l = 16 x 0,0160 x 60 = 15,36 mm

As can be seen in figure 12-14, a correct compensation of the expansion depends also on the placement of fixing devices such as saddles and clips. Never plan for or place tube saddles as a mounting device close to a tube connection. Clips should be positioned such that they do not behave as a fixed restraint. When there are straight segments of tube, without expansion compensation, use only one saddle to prevent possible deformation. Position it as close to the middle of the straight segment as possible: in this way, any expansion will be distributed in both directions and the length of the expansion equalizer required will be halved. It is recommended that tube saddles with a rubber inlay are used as this muffles any possible noise and vibration and provides a better distribution of the stresses.

Providing suitable solutions

59

2.6 2.6.2 Flow loss Every fluid that flows through a tubing system experiences continuous and local flow resistances that are apparent from the pressure drop in the system. There is a difference between the continuous and the local pressure drop. The continuous pressure drop is mainly caused by the flow resistance in straight tube sections which in turn essentially results from the friction between the fluid and the tube wall. Local pressure drops, on the contrary, are those flow resistances that are caused by turbulence, for instance where there is a change of internal tube diameter, a tube branch, in an elbow, etc.

60

Continuous pressure drop To calculate the total pressure drop resulting from the flow of fluids in a straight section of the tubing system, first determine the pressure drop over a unit of length and then multiply the total length with this value. This value can be determined analytically using the Hazen-Williams formula. 6,05 x 105 p = ------------------------- x Q1,85 C1,85 x di4,87

61

700

= pressure loss in the tube [bar/m] = flow through the tube [l/min] = mean internal diameter of the tube [mm] = constant for type and condition of the tube C=140 for XPress carbon and stainless tube

0,1

p Q di C

80° hot water

For those who wish to make these calculations, we refer to the relevant discipline literature. For the normal installation calculations, appropriate diagrams, such as given in figure 15 opposite, can be used to solve this problem. The unit pressure drop [R] and the flow velocity [m/s] for a given water flow rate can be determined with these simple and quick means. 27

Figure 15 Providing suitable solutions

2.6 Once [R] and the actual or equivalent length of the tubing system are known, the total pressure drop over the particular segment can be calculated. The diagram gives values that apply to water with a temperature of 80°C. It can be seen that [R] changes with temperature and, as such, a correction is needed. Diagrams for the different operating temperatures and various velocity ranges can be prepared. For example a diagram applicable to water with a temperature of 10°C is used when dealing with normal water supply systems with its corresponding significantly higher velocity ranges. As well as the temperature, any water additives e.g. anti-freeze will affect the value [R] and will need to be corrected accordingly. It would be too complex to use several diagrams to calculate each temperature. That is why one can use the nomogram in figure 16, which gives the correction factor [Kc] that needs to be applied to [R] for the actual temperature of the fluids. The following example explains the use of the nomogram. Assume a flow rate of 700 l/h with a tube diameter of 22 x 1,2 mm. For 80°C hot water, the value of R is 27 WS/m (approx. 270 Pa/m). The value of [R] for 40°C warm water is calculated as follows: as in the nomogram of figure 16, the correction factor [Kc] is 1,0 for a water temperature of 10°C, the value of [R] for this temperature can initially be ascertained. The value obtained is multiplied by the correction coefficient [Kc] for the temperature of 40°C:

62

0,89

R = (27/0,82) x 0,89 = 29,3 mm WS/m [29,3 mbar/m]. Local pressure drops Local pressure drop is, as mentioned in the introduction of this section, the resistance to flow that results from changes in the flow direction and cross-sectional area, flow splitting over several channels, etc. There are in general two possibilities to calculate these flow resistances: the direct analytical method and the method using equivalent lengths.

0,82

Figure 16 Providing suitable solutions

63

2.6 Equivalent length method This is a calculation method that solves the calculation problem as a function of a particular local resistance and gives the equivalent length of a straight piece of tube with the same diameter that would have the same pressure drop. In order to use this method of calculation all length-equivalent values for each fitting type in table 24 are to be added to the actual length of the supply network. This will show the overall resistance in the circuit. This method is not as accurate as the direct method but has the advantage that the calculation can be carried out faster.

Table 25 gives the [ζ] values for every type of fitting. We can assume that [ζ] is velocity independent for those velocities that occur in domestic installations or in other normal applications; this is supported by the fact that the change of [ζ] as a function of the Reynolds number in these velocity ranges is only minimal. Once the [ζ] value is known, one can read off directly the corresponding local pressure drop.

DN 12 - 100 (Ø 15 - 108 mm) DN 64

DN 12 - 50 (Ø 15 - 54 mm)

Method of equivalent length (m) 1,5 0,7 0,5 0,5 0,4 DN 65 - 100 (Ø 76,1 - 108 mm) 1,3 0,6 0,4 0,5

0,1

0,9 1,0

1,3 1,3

Table 24: Table of equivalent meters

Direct analytical method The local pressure drop can be calculated with the following mathematical equation: ∆pL= ∑ζ x v2 x γ/2 x 10 -5 [bar]

v = flow velocity of the fluid [m/s] γ = specific density of the fluid [kg/m3] ζ = local flow resistance coefficient

1,5 1,5

3,0 3,0

ζ Direct analytical method

12

0,9

0,4

0,3

0,3

0,25

0,5

0,7

0,9

1,8

15

1,1

0,5

0,4

0,4

0,30

0,65

0,9

1,1

2,5

20

1,4

0,6

0,5

0,5

0,4

0,8

1,2

1,4

2,8

25

1,9

0,9

0,6

0,6

0,5

1,1

1,5

1,9

3,8

32

2,5

1,2

0,8

0,8

0,7

1,5

2,1

2,5

5,0

40

3,1

1,4

1,0

1,0

0,9

1,8

2,6

3,1

6,2

50

4,0

1,8

1,3

1,3

1,1

2,3

3,3

4,0

8,0

65

6,1

2,8

1,9

2,4

0,5

4,7

6,1

7,1

14,2

80

7,8

3,6

2,4

3,0

0,6

6,0

7,8

9,0

18,0

100

10,6

4,9

3,3

4,1

0,8

8,2

10,6

12,3

24,6

Table 25: Table of localized flow loss values

Providing suitable solutions

65

2.6 2.6.3 Heat losses

Figures 17, 18, 19 and 20 show the linear heat losses of the tubes according to their diameter and temperature difference. The details in figures 17, 18 and 19 refer to bare tubes placed above screed. Figure 20 shows the heat loss for polypropylene coated tubes.

Respective insulation for limiting heat losses is also required for the tubes in the XPress System, not just to save energy but also based on current norms and legal provisions (for example German law of 10/91, DIN 1988, part 2, EnEV). We refer to these regulations and their implementation regulations and the respective tables showing the minimum insulation thickness. 100

linear heat loss for stainless steel tubes 15 18 22 28 35 42

54

100 76,1

90

70 60

108 ∆t [K]

∆t [K]

60 50

40

30

30

20

20

10

100

100 heat loss [W/m]

150

0

200

linear heat loss for carbon steel tubes 12 15 18 22 28 35 42 54 76,1

88,9

108

100

80

80

70

70

60

60 ∆t [K]

90

50

40

30

30

20

20

10

10

Figure 19

100 heat loss [W/m]

150

200

60 40 heat loss [W/m]

80

linear heat loss for polypropylene coated carbon steel tubes 15 18 22 28 35 42

100

54

50

40

50

20

Figure 18

90

0

Table 26 on the following pages gives the friction loss R in the tube as a function of the throughput Q and the flow velocity at a temperature of 10 °C for stainless steel tubes according DVGW - worksheet GW 541 (2004) series 2, with a wall roughness [k] of 0,0015 mm. The tables for XPress carbon steel tube and copper tube as well as the tables for other situations (for example other temperatures or other applications) are available at VSH or can be downloaded at: www.vsh-fittings.com

10 50

Figure 17

∆t [K]

50

40

0

54

80

70

66

42

2.6.4 XPress tube

90

88,9

80

linear heat loss for copper tubes 12 15 18 22 28 35

0

20

Figure 20

60 40 heat loss [W/m]

80

100

Providing suitable solutions

67

0,8 2,7 5,5 9,1 13,5 18,5 24,3 30,8 37,9 45,7 54,1 63,2 72,9 83,2 94,1 105,6 117,6 130,3 143,6 157,4

0,2 0,5 0,7 1,0 1,2 1,6 1,7 2,0 2,2 2,5 2,7 3,0 3,2 3,5 3,7 4,0 4,2 4,5 4,7 5,0

0,3 1,0 1,9 3,3 4,8 6,5 8,6 10,8 13,4 16,0 19,0 22,2 25,5 29,1 33,0 37,0 41,2 45,6 50,3 55,1 60,1 65,3 70,7 76,3 82,1 86,1 94,2 100,8 107,1 113,9 120,8 127,9

0,2 0,3 0,5 0,6 0,8 1,0 1,1 1,3 1,4 1,5 1,8 1,9 2,1 2,2 2,4 2,5 2,7 2,9 3,0 3,2 3,3 3,5 3,7 3,8 4,0 4,1 4,3 4,5 4,6 4,8 4,9 5,1

0,1 0,3 0,7 1,1 1,6 2,1 2,8 3,5 4,4 5,3 6,2 7,3 8,3 9,5 10,8 12,0 13,5 14,8 15,4 17,9 19,6 21,2 23,0 24,8 26,7 28,6 30,7 32,7 34,8 37,0 39,2 41,5 43,8 46,3 48,7 51,2 53,8 56,5 59,3 62,0 64,8 67,6 70,5 73,5 76,5 79,6 82,8 86,0

0,1 0,2 0,3 0,4 0,5 0,6 0,7 0,8 0,9 1,0 1,1 1,2 1,3 1,4 1,5 1,6 1,7 1,8 1,9 2,0 2,1 2,2 2,3 2,4 2,5 2,6 2,8 2,9 3,0 3,1 3,2 3,3 3,4 3,5 3,6 3,7 3,8 3,9 4,0 4,1 4,2 4,3 4,4 4,5 4,6 4,7 4,8 4,9

0,2 0,4 0,6 0,8 1,0 1,2 1,4 1,6 1,8 2,0 2,2 2,4 2,6 2,8 3,0 3,2 3,4 3,6 3,8 4,0 4,2 4,4 4,6 4,8 5,0 5,2 5,4 5,6 5,8 6,0 6,2 6,4 6,6 6,8 7,0 7,2 7,4 7,6 7,8 8,0 8,2 9,0 10,0

0,3 1,1 2,3 3,8 5,7 7,8 10,3 13,1 16,2 19,5 23,1 27,0 31,2 35,7 40,4 45,3 50,6 56,1 61,8 67,8 74,1

0,2 0,5 0,7 1,0 1,2 1,5 1,7 2,0 2,2 2,5 2,7 3,0 3,2 3,5 3,7 4,0 4,2 4,5 4,7 5,0 5,2

0,1 0,4 0,9 1,5 2,2 3,1 4,0 5,1 6,3 7,6 9,0 10,5 12,1 13,8 15,6 17,5 19,5 21,6 23,8 26,2 28,6 31,0 33,6 36,3 39,1 42,0 44,9 48,0 51,1 54,4

0,2 0,3 0,5 0,7 0,8 1,0 1,2 1,3 1,5 1,7 1,8 2,0 2,2 2,3 2,5 2,7 2,8 3,0 3,2 3,3 3,5 3,7 3,9 4,0 4,2 4,4 4,5 4,7 4,9 5,0

0,0 0,1 0,3 0,5 0,7 0,9 1,2 1,6 1,9 2,3 2,6 3,1 3,6 4,1 4,6 5,2 5,8 6,5 7,1 7,7 8,4 9,2 10,0 10,8 11,6 12,5 13,3 14,2 15,0 16,1 17,1 18,0 19,1 20,2 21,3 22,3 23,5 24,7 25,9 27,0 28,3 33,5 40,6

v [m/s]

R [bar/m]

54 x 1,5 mm

v [m/s]

R [bar/m]

42 x 1,5 mm

v [m/s]

R [bar/m]

35 x 1,5 mm

v [m/s]

R [bar/m]

28 x 1,2 mm

v [m/s]

R [bar/m]

v [m/s]

R [bar/m]

v [m/s] 0,4 0,8 1,1 1,5 1,9 2,3 2,8 3,0 3,4 3,8 4,1 4,5 4,9 5,3

22 x 1,2 mm

Maximum throughput Q s [ l/s ]

2,2 7,3 14,8 24,5 36,2 49,9 65,8 83,1 102,4 123,8 146,5 171,1 197,5 225,5

18 x 1,0 mm

Table 26: Tube friction values (only for stainless steel)

68

0,05 0,10 0,15 0,20 0,25 0,30 0,35 0,40 0,45 0,50 0,55 0,60 0,65 0,70 0,75 0,80 0,85 0,90 0,95 1,00 1,05 1,10 1,15 1,20 1,25 1,30 1,35 1,40 1,45 1,50 1,55 1,60 1,65 1,70 1,75 1,80 1,85 1,90 1,95 2,00 2,05 2,10 2,15 2,20 2,25 2,30 2,35 2,40

R [bar/m]

Maximum throughput Q s [ l/s ]

2.6 15 x 1,0 mm

0,1 0,2 0,3 0,4 0,5 0,6 0,7 0,8 0,9 1,0 1,1 1,2 1,3 1,4 1,5 1,6 1,7 1,8 1,9 2,0 2,1 2,2 2,3 2,4 2,5 2,6 2,8 2,9 3,0 3,1 3,2 3,3 3,4 3,5 3,6 3,7 3,8 3,9 4,0 4,1 4,2 4,6 5,1

Providing suitable solutions

69

0,1 0,4 0,8 1,4 2,0 2,8 3,7 4,7 5,9 7,1 8,4 9,9 11,4 13,0 14,8 16,6 18,5 20,6 22,7 24,9 27,2

0,2 0,5 0,7 1,0 1,2 1,5 1,7 2,0 2,2 2,5 2,7 2,9 3,2 3,4 3,7 3,9 4,2 4,4 4,7 4,9 5,1

0,1 0,2 0,4 0,6 0,9 1,3 1,7 2,2 2,7 3,2 3,8 4,5 5,2 5,9 6,7 7,5 8,4 9,3 10,3 11,3 12,4 13,4 14,6 15,7 17,0 18,2 19,6 20,9 22,2

2.7 Building-in

0,2 0,4 0,5 0,7 0,9 1,1 1,2 1,4 1,6 1,8 1,9 2,1 2,3 2,5 2,7 2,8 3,0 3,2 3,4 3,5 3,7 3,9 4,1 4,2 4,4 4,6 4,8 5,0 5,1

0,0 0,1 0,1 0,2 0,4 0,5 0,6 0,8 1,0 1,2 1,4 1,7 2,0 2,2 2,5 2,8 3,2 3,5 3,9 4,3 4,6 5,1 5,5 5,9 6,4 6,8 7,3 7,8 8,4 8,9 9,5 10,0 10,6 11,1 12,3 12,9 13,6 14,3 15,0 15,7 16,4 17,1 17,9

2.7.1. Recommendations v [m/s]

R [mbar/m]

108 x 2,0 mm

v [m/s]

v [m/s]

R [mbar/m]

88 x 2,0 mm

0,1 0,2 0,4 0,5 0,6 0,7 0,8 0,9 1,1 1,2 1,3 1,4 1,5 1,7 1,8 1,9 2,0 2,1 2,2 2,4 2,5 2,6 2,7 2,8 3,0 3,1 3,2 3,3 3,4 3,5 3,7 3,8 3,9 4,0 4,2 4,3 4,4 4,6 4,7 4,8 4,9 5,0 5,2

Table 27: Tube friction values (only for stainless steel)

70

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43

R [mbar/m]

Maximum throughput Qs [ l/s ]

2.7 76 x 2,0 mm

For esthetical and practical reasons it is rare that tubes are installed uncovered in modern installations other than in auxiliary rooms, such as cellars and garages. The installation of tubes under screed, inside the wall or floor requires several precautionary measures that are depicted schematically in the figures 21 and 22. The following systems can be installed under screed: - XPress stainless steel without corrosion protection* - XPress stainless steel GAS without corrosion protection* - XPress carbon steel polypropylene coated (Fittings must be protected against corrosion) - XPress copper with corrosion protection (e.g. synthetic coated) - XPress copper GAS with corrosion protection (e.g. synthetic coated). Important: tubes for water laid under screed (e.g. walls or floors) should always have a suitable coating to achieve a significant separation between the tube and the building structure (e.g. due to noise protection).

Figure 21

Figure 21 shows a cross-section of a tube installed inside a wall. The tubes and fittings have to be wrapped by an elastic and pliable coating that isolates the installation fully from the building so that there are no direct contacts. For this purpose isolation materials prescribed by DIN 1988 are a good solution and also have a heat insulating effect.

Similarly for tubes installed inside floors, even sprung floors, make sure that the horizontal stretches are isolated by a mantle such as shown in figure 21. Figure 22 * In chloride-containing building materials, stainless steel tubes must be protected accordingly.

Providing suitable solutions

71

2.7 Also ensure that an adequate elastic bushing has been used where the tube exits the floor so that any tube geometry changes do not cause the tube to come into contact with the cement (see figure 22).

72

Figure 23 shows a classical situation of branching from the outside standpipe to a point in the building. In this case, make sure that the T-piece is not subjected to stress that could result in a change of the direction of the axis of the fitting. In this context the attachment saddles, as fixed mounting points, and clips are therefore very important. For all installations however, the tubes and fittings should be enclosed with a soft material as a general rule in order to allow expansion. We point out once more that insulation- and surrounding material in the case of stainless steel may not admit any diffusion from chloride ions. In the case of copper, surrounding materials such as ammonia or nitrates must be prevented from penetrating the insulating material. Guidelines for the fitting distances for pipelines Distance between supports for pipelines Ø Tube diameter [mm] 15 x 1,0

Maximum distance [m] 1,25

18 x 1,0

1,50

22 x 1,2

2,00

28 x 1,2

2,25

35 x 1,5

2,75

42 x 1,5

3,00

54 x 1,5

3,50

64 x 1,5

4,25

67 x 1,5

4,25

76,1 x 2,0

4,25

88,9 x 2,0

4,75

108 x 2,0

5,00

Adherence to the distances above and between attachment points is not sufficient by itself. Heat expansion also needs to be appropriately compensated for in horizontal stretches, and therefore the distances above may need to be changed.

2.7.2 Tube fastening When fastening the tubes, bear in mind the following: The bearing capacity of the fastenings must correspond to the weight of the pipelines and also withstand expansion and torsion forces. Based on this, attachment saddles, as fixed mounting points, and clips must be correctly inserted and assembled. Attachment points may only be fitted onto straight tube sections. They may not be fitted onto shaped parts.

2.7.3 Pressure test Completed pipelines are checked for leaks before being covered up. With potable water and heating installations the pressure test can be carried out with water, air or inert gases. The test medium and the results of the pressure test are to be documented in a so-called pressure test report. Important: VSH stipulates that a pressure test of the piping system must be carried out in all cases. Before being sealed, insulated, painted or installed a line must first undergo a pressure test in order to determine that there are no leaks. Pressure test should always be performed in accordance with local regulations. As a rule of thumb a pressure of 1,5 times the operating pressure is used for pressure tests with water.

Figure 23

Note: Because of corrosion risk make sure that after testing with water in carbon press installations there is no water left in the pipe system unless the system is going to be operational in a short term.

Table 28: Distance between supports according to DIN 1988, part 2 Providing suitable solutions

73

2.7

74

Pressure test of potable water systems

Pressure test of sprinkler systems

Pressure test with water Important: The pressure test with water on drinking water pipelines that have already been laid is performed in accordance with the ZVSHK/BHKS technical bulletins. The medium used for the pressure test with water must be of drinking water quality (free of oil and other impurities) in order to avoid contamination of the pipeline system. After being filled with pure water the pipe must be properly bled.

The tubes belonging to the sprinkler system must be subjected to a pressure test according to valid guidelines, for example CEA 4001, no. 17.1.1. (VdS) lasting at least two hours. During the test a pressure (measured at the alarm valves) corresponding to 1,5 times the permitted positive operating pressure - but at least 15 bar - must be maintained. This pressure test is a check of both the strength and tightness of the system. The pressure loss, for example due to temperature changes, should be monitored for 24 h. Dry sprinkler systems shall also be tested pneumatically to a pressure of not less than 2,5 bars for not at least 24 hours. Every leakage which occurs and results in a pressure drop of more than 0,15 bar for the 24 h, shall be corrected. Any faults disclosed, such as permanent deformations, ruptures or leakages shall be corrected, and the pressure test must be repeated.

Pressure test with air Important: The pressure test with air or inert gases can be carried out in accordance with the ZVSHK/BHKS technical bulletins “Pressure Test with Air or Inert Gases”. For safety reasons, the maximum test pressure is set to 3 bar, a maximum test pressure which also applies for gas pipe.

Pressure test for heating systems and cooling systems

2.7.4 F  lushing the network

Important: As a rule the pressure test on pipes that have already been laid is carried out with water in accordance with DIN-VOB 18380. • The test pressure at each point of the system must be 1,3 times the operating pressure and at least 1 bar overpressure. • Immediately after the cold water pressure test the water should be heated up to the highest hot water temperature on which the calculation was based in order to determine whether the system remains tight at high temperatures. • During the test there must be no drop in pressure. • The pressure test should be sufficiently documented.

All pipelines are to be flushed thoroughly before taking into use so that foreign matter and foreign substances are removed from the inside of the tube surface and so that hygiene problems and corrosion damage is largely prevented. The potable water pipeline must be flushed as soon as possible after installing the pipelines and following the pressure test. The cold- and hot water pipelines should be flushed separately, intermittently and under pressure with an air-water mixture (DIN 1988, part 2). The medium for flushing the pipes should be of drinking water quality to prevent possible contamination of the pipe system.

Pressure test for natural gas systems Important: The pressure test for natural gas and liquid gas systems must be performed in accordance with local regulations such as for example DVGW G600/TRGI 86/96.

Providing suitable solutions

75

2.8 2.8 Corrosion There are different kinds of corrosion: chemical corrosion, electrochemical corrosion, internal and external local corrosion, stray current corrosion, etc. In general, all these kinds of corrosion have very particular chemical or mechanical causes. The following section provides some simple hints that will help to prevent occurrence of these problems.

76

Electrochemical corrosion For electrochemical corrosion to take place, the following conditions would have to be present: - An electrochemical potential difference between both parts - The presence of a conductive fluid (electrolyte), such as water - The presence of oxygen, O2. One should differentiate between heating installations and water supply installations. There are no significant amounts of oxygen in heating installations, when they are properly installed and operated and there will thus be very little corrosion. In potable water installations however, the oxygen content is very high, near the saturation level.

It is therefore recommended to avoid using extensions or connection pieces of galvanized steel as far as possible and instead to use fittings from stainless steel or brass. Stray currents Corrosion by stray currents rarely occurs in practice and it is immediately recognisable as it starts on the outside of the tube with a cone-shaped crater to the inside. Stray current corrosion requires a direct current that turns the metal into an anode. The current in reality that, despite isolation measures, penetrates into the earth and goes on into other neighbouring metal structures, such as a water supply installation, runs through a particular stretch of the system before it returns to earth again. In order to penetrate into the tubing system, the earth current must have an entry point where the normal protective cover of the tube or connection is damaged or missing. For this reason, metal pipelines must be earthed (see EU Regulations). Direct current installations are generally not used in domestic households and no real problems occur with alternating current. Research over decades has shown that problems by stray currents only occur sporadically and do not depend on the type of metal.

2.8.1 Stainless steel It is of primary importance that the XPress System components are only installed downstream of other, metallurgically inferior (less noble), components that are possibly present in these kind of installations. For example, it is possible to install branches with XPress stainless steel tubes from a tube system consisting of galvanised steel tubes. Conversely, a connection piece of non-ferrous metal or synthetics can be used (see DIN 1988). Another important factor is the ratio between the surface of the noble metal and that of the less noble metal. The higher this ratio, the greater the corrosion rate may be.

Internal corrosion XPress stainless steel tubes and press fittings are completely passive when in contact with potable water and therefore not at risk from corrosion. Potable water is considered as water with properties conforming to current regulations on physical-chemical tolerances. The tubes and fittings also react in a safe and problem-free manner regarding the water’s chlorine content if 1,34 mg/l is added for disinfecting purposes. The XPress stainless steel system can also be used for all water treatment plants for domestic purposes (e.g. for water hardeners).

Providing suitable solutions

77

2.8

78

It is corrosion-resistant against glycol-containing, de-mineralized or distilled water. Hygiene problems regarding heavy metal contamination do not occur when using XPress stainless. Point or crack corrosion can only occur when the maximum values for the chloride content in water, as defined in the applicable regulations, are significantly exceeded.

External corrosion In general carbon steel systems are installed in such a way that the outer surfaces do not come into contact with corrosive media. However, XPress carbon steel tubes should not be permanently exposed to moisture. XPress carbon steel tubes with PP coating provide a good corrosion protection.

External corrosion External corrosion of the XPress stainless system components can only occur when wet potable water tubes come into contact with mortar, droplets or covers that contain or create chlorides. Ensure that the outer isolation layer of the tubes and fittings is continuous and that sufficient corrosion-protective isolation tape is applied if necessary. The use of closed-cell insulation has proven to be an effective protection against corrosion.

2.8.3 Corrosion prevention In the following paragraphs, instructions are given for preventing the corrosion problems in the usual areas of application. We distinguish between inner- and outer corrosion and area of application. We shall also be going into the various application possibilities of various materials that can be combined in an installation (combi installation).

A. Inner corrosion

2.8.2 Carbon steel Internal corrosion Internal corrosion cannot occur with closed water heating systems. The oxygen in the water in closed systems is used to create iron oxide on the inside of the tube meaning further corrosion is no longer possible. When the heating system is not in use, it must be kept full at all times, or, alternatively, be completely drained and subsequently dried out, to avoid the presence of water and oxygen in the system at the same time. The respective additives should be added to prevent frost damage, calcification or corrosion. Enquiries for the use of additives can be done at any time. To prevent outer corrosion, please observe the respective laws, regulations and rules of the DVGW, DIN or other institutes.

A.1 Heating installations The penetration of oxygen in closed heating installations is prevented if high quality fittings and compensators with closed membranes are used. When filling the installation, a small quantity of oxygen contained in the water is directly absorbed into the inner tube surface in which a thin layer of iron oxide is formed after which there is no longer any possibility of corrosion. The loss in wall thickness can be disregarded. The heating-circuit water is practically oxygen-free after this reaction.

Stainless steel Tubes and fittings of stainless steel are suitable for all open and closed heating installations. Combi installations: Stainless steel can be used in combi installations with other materials in any sequence.

Providing suitable solutions

79

2.8 Carbon steel

Carbon steel – copper – stainless steel. Combi installations: These steel combinations are possible in all closed systems without limitation.

components are suitable for all conditioning methods (water hardening) regarding conditioned potable water installations and are also corrosion resistant with regard to glycol-containing-, demineralized- or distilled water. XPress stainless fittings and stainless tubes are however not suitable for operation in metering systems as for example disinfectants, which are added to the potable water. XPress stainless fittings and tubes are also suitable for all other open and closed water systems (e.g. cooling water). Combi installations: The corrosion behaviour of stainless steel is not influenced by its use in combi installations independent of the direction of the flow of water (no flow rule). Combi installations can be used with stainless steel in any sequence. Discolouration from a deposit of foreign corrosion products does not indicate corrosion on the stainless steel. Stainless steel can be used with all copper alloys (red bronze, copper or brass) in a combi installation. Stainless steel is not at risk from contact corrosion.

Water additives

Carbon steel

As a preventive measure against inadmissible oxygen absorption, oxygen inhibitors can be added to the heating-circuit water. Observe the supplier’s instructions for use.

Carbon steel tubes and fittings are not allowed in potable water installations. In the case of galvanized steel, contact corrosion will occur if this is brought into direct contact with stainless steel.

Inner corrosion is normally impossible in closed heating installations with carbon steel tubes and fittings as oxygen from outside cannot penetrate the installation. Combi installations: Unalloyed galvanized steel can be used without problems and can be combined with other metals in any sequence in closed systems.

Copper Copper is suitable for all open and closed heating systems. Combi installations: Copper can be used with other metals in any sequence in combi installations.

80

Other combinations possibilities

 A.2 (Potable) water installations Stainless steel The stainless steel in XPress fittings and tubes has the advantage that stainless steel is passive in potable water. The physical and chemical properties of the potable water are not affected by stainless steel. In this passive condition, no internal corrosion will take place. With the use of tubes and connection pieces from stainless steel, the danger of heavy metal contamination is avoided and the growth of bacteria is countered. Discharge or ring corrosion can only occur if the chloride content of the water is significantly higher than the maximum level allowed under current regulations. XPress stainless system

With the use from fittings of red brass, copper or brass between the carbon steel tube and the stainless steel, the possibility of contact corrosion is negligibly small. Contact corrosion on a carbon steel tube can also be prevented using 50 mm couplings made of red bronze, copper or brass.

Copper The physical and chemical properties of potable water can be affected by copper in the event of inner corrosion. An unfavourable potable water composition can also lead to corrosion.

Providing suitable solutions

81

2.8 The limit values for the use of copper material with respect to the salt content of the potable water must therefore correspond to the legal requirements for potable water. If these limit values are adhered to and the potable water composition does not deteriorate, copper is suitable for potable water installations. Combi installations with copper and carbon steel: On application of copper and carbon steel tubes in water systems including open water systems and due to the various properties of the metals, the following rule is important: Flow from base metal to the noble metal

82

Copper should always be used after couplings/tubes of carbon steel as per the direction of the flow of water. Base

Carbon steel

Noble

Stainless steel

Copper

The flow from base metal to noble metal

B. Outer corrosion B.1 General Situations causing outer corrosion do not usually occur in buildings. It is however possible that installations in many cases are for a longer period subject to undesired penetration of rain, humidity or dampness, which can lead to problems. Responsibility for the carrying out of measures rests however with the operator and the fitter. Only suitable corrosion protection can offer permanent safety against corrosion. For this application, there is the possibility of “closed cell” insulation, which must be applied in a guaranteed waterproof condition.

Suitable basic- or metallic paints can offer minimum corrosion protection. It is advisable to always use corrosion protection on the pipelines in situations where corrosion is likely to occur (damp room, crawl spaces, etc.).

B.2 Stainless steel Outer corrosion can only occur in the following circumstances: - If stainless steel heat-conducting pipelines (50°C) come into contact with chloride-containing building and insulating materials (through the effects of humidity) - If water vapour on stainless steel heat-conducting pipelines leads to a local chloride concentration - If stainless steel pipelines (also in the case of cold water pipelines) come into contact with chlorine gas, saltwater or (oxygen-saturated) water with a high chlorine content. If there is the danger of building material coming into contact over a long period with highly chlorinated water, suitable corrosion protection must be used. Stainless steel tubes in cement floors will not be subject to electrolytic outer corrosion in connection with the potential equalization.

B.3 Carbon steel Special consideration should be given to preventing outer corrosion in an environment remaining humid for a longer period. Only in the case of sporadic shorter corrosion stress by humidity will carbon steel also be resistant against corrosion for a longer period. Carbon steel press fitting connections must be protected in the case of increased risk of corrosion due to electrolytic outer corrosion (or longer periods of humidity). A synthetic coat of polypropylene offers carbon steel tubes effective corrosion protection.

Providing suitable solutions

83

2.8 B.4 Copper

Connections

Copper’s great deal of corrosion resistance makes corrosion protection measures superfluous. With copper tubes in cement floors, no outer electrolytic outer corrosion takes place in connection with the potential equalization. However, sometimes also copper pipelines must be protected from the influence of outer corrosion such as sulphite, nitrite and ammonia. Gas tubes must be protected against corrosion.

There is a danger of point or crack corrosion when soldering stainless steel fluid tubes. In the case of TIG welding of stainless steel, discolouration occurs at the welding joints, which on contact with salty water can lead to corrosion. This discolouration, mainly on the inside of the tube can only be removed by etching, which is not practical with pipelines that have already been installed.

C. Influence of application and processing C.1 General 84

Corrosion may occur due to incorrectly designed installations and faulty operational applications. The following points must be observed:

C.2 Stainless steel

C.3 Stainless steel – carbon steel – copper With all material (stainless steel, carbon steel, copper), waterline corrosion can occur via a three-phase interface (water – metal – gas (air)). This corrosion can be prevented if the tubing installation remains permanently filled following the first filling. Partial filling will take place for example, if the tubes are emptied again after a compression test with water in which case compression tests using gas/air are to be recommended.

Grinding stainless steel

D. Effect of insulation

Grinding through stainless steel tubes due to the high heat development is not permitted.

D.1 General

Bending stainless steel tubes Stainless steel tubes may not be bent warm. The heating up of the stainless steel tube will alter the structure of the material (sensitization) and inter-crystalline corrosion can take place.

Heat transfer (e.g. with a heating band) Heat transfer from outside inwards must be prevented as this can lead to the build-up of film on the inside of the tube wall. This film can cause the increase in the concentration of chloride ions, which cause discharge corrosion in critical concentrations.

Insulation normally offers no protection against corrosion except for “closed cell insulation” (sealed watertight), which offers effective corrosion protection.

D.2 Insulating stainless steel Insulating material that release chloride ions towards the water or which could cause a local increase in chloride ions are not permitted. The thermal insulation of tubes may include a mass proportion of up to 0,05% of water-soluble chloride ions (AS quality).



Providing suitable solutions

85

3 D.3 Insulating galvanized steel

3 Certificates

If there is no humidity between the insulation material and the tube, no corrosion can occur. If underneath the insulation, (condensation-) humidity can occur, the outside of the tube will corrode.

D.4 Insulating copper Insulation for copper must be nitrate-free and may contain a proportion of nitrate no more than 0,02%.

86

87

Providing suitable solutions

3

88

89

Providing suitable solutions

90

91

Providing suitable solutions

5 4 Guarantee For the actual terms of guarantee on XPress please contact your local agent.

VSH 5 Combination pressings

92



93

Providing suitable solutions

5 Carbon steel

Minimum distance between pressings

DN 10 12 15 20 25 32 40 50 65 80 100

Stainless steel

94

DN 12 15 20 25 32 40 50 65 80 100

Outer Ø D-min 15 18 22 28 35 42 54 76,1 88,9 108

Tube length L-min 50 50 52 56 62 80 90 165 186 234

Minimum fitting distance A-min 10 10 10 10 10 20 20 40 50 50

Insertion depth e 20 20 21 23 26 30 35 55 63 78

Tube length L-min 50 50 52 56 62 80 90

Minimum fitting distance A-min 10 10 10 10 10 20 20

Insertion depth e 20 20 21 23 26 30 35

Stainless steel GAS DN 12 15 20 25 32 40 50

Outer Ø D-min 15 18 22 28 35 42 54

Outer Ø D-min 12 15 18 22 28 35 42 54 76,1 88,9 108

Tube length L-min 44 50 50 52 56 62 80 90 165 186 234

Minimum fitting distance A-min 10 10 10 10 10 10 20 20 40 50 50

Insertion depth e 17 20 20 21 23 26 30 35 55 63 78

95 Copper DN 10 12 15 20 25 32 40 50 65 65 80 100

Outer Ø D-min 12 15 18 22 28 35 42 54 64 76,1 88,9 108

Tube length L-min 44 50 50 52 56 62 80 90 130 140 174 185

Minimum fitting distance A-min 10 10 10 10 10 10 20 20 30 40 50 50

Insertion depth e 17,0 20,0 20,0 21,0 23,0 26,0 30,0 35,0 50,0 50,0 62,0 67,5

Providing suitable solutions

5 Carbon steel

Tee pieces with equal outlet

DN 10 12 15 20 25 32 40 50 65 80 100

Stainless steel

96

DN 12 15 20 25 32 40 50 65 80 100

Outer Ø

Tube length L-min 50,0 50,0 52,0 56,0 62,0 80,0 90,0 150,0 176,0 204,0

15 18 22 28 35 42 54 76,1 88,9 108

88,0 91,0 97,0 107,0 120,0 143,0 165,0 270,0 304,0 360,0

Z-value Z 19,0 20,5 22,5 25,5 29,0 31,5 37,5 60,0 64,0 78,0

78,0 88,0 90,0 104,0 118,0 140,0 162,0

Z-value Z 14,0 19,0 19,0 24,0 28,0 30,0 36,0

X-min

Stainless steel GAS DN 12 15 20 25 32 40 50

Outer Ø 15 18 22 28 35 42 54

Tube length L-min

X-min 50,0 50,0 52,0 56,0 62,0 80,0 90,0

Outer Ø

Tube length L-min

12 15 18 22 28 35 42 54 76,1 88,9 108

X-min 44,0 50,0 50,0 52,0 56,0 62,0 80,0 90,0 150,0 176,0 204,0

89,0 98,0 101,0 107,0 117,0 130,0 153,0 175,0 282,0 302,0 354,0

Z-value Z 22,5 24,0 25,5 27,5 30,5 34,0 36,5 42,5 66,0 63,0 75,0

97

Copper DN 10 12 15 20 25 32 40 50 65 65 80 100

Outer Ø 12 15 18 22 28 35 42 54 64 76,1 88,9 108

Tube length L-min

Z-value Z

X-min 44,0 50,0 50,0 52,0 56,0 62,0 80,0 90,0 130,0 140,0 174,0 185,0

66,0 74,0 78,0 84,0 94,0 110,0 136,0 158,0 298,0 270,0 374,0 369,0

11,0 12,0 14,0 16,0 19,0 24,0 28,0 34,0 84,0 65,0 100,0 92,0

Providing suitable solutions

5 Carbon steel

Minimum distance between 2 tee pieces with equal and reduced outlet

Stainless steel

98

DN

Outer Ø

12 15 20 25 32 40 50 65 80 100

15 18 22 28 35 42 54 76,1 88,9 108

Tube length L-min X-min 50,0 50,0 52,0 56,0 62,0 80,0 90,0 150,0 176,0 204,0

12 15 20 25 32 40 50

Outer Ø 15 18 22 28 35 42 54

Tube length L-min X-min 50,0 50,0 52,0 56,0 62,0 80,0 90,0

15,0 16,5 18,5 21,5 25,0 30,0 36,0 61,0 68,0 79,0

Z-value Z1 84,0 88,0 93,0 102,0 111,0 138,0 162,0

10 12 15 20 25 32 40 50 65 80 100

12 15 18 22 28 35 42 54 76,1 88,9 108

Tube length L-min X-min 44,0 50,0 50,0 52,0 56,0 62,0 80,0 90,0 150,0 176,0 204,0

Z-value Z1 71,0 80,0 83,0 89,0 99,0 112,0 140,0 162,0 270,0 312,0 354,0

13,5 15,0 16,5 18,5 21,5 25,0 30,0 36,0 60,0 68,0 75,0

Copper

Stainless steel GAS DN

Outer Ø

99

Z-value Z1 80,0 83,0 89,0 99,0 112,0 140,0 162,0 272,0 312,0 362,0

DN

DN

Outer Ø

10 12 15 20 25 32 40 50 65 65 80 100

12 15 18 22 28 35 42 54 64 76,1 88,9 108

Tube length L-min X-min 44,0 50,0 50,0 52,0 56,0 62,0 80,0 90,0 130,0 140,0 174,0 185,0

Z-value Z1 66,0 74,0 78,0 84,0 94,0 110,0 136,0 158,0 296,0 276,0 374,0 369,0

11,0 12,0 14,0 16,0 19,0 24,0 28,0 34,0 83,0 68,0 100,0 92,0

17,0 19,0 20,5 23,0 24,5 29,0 36,0

Providing suitable solutions

5 Stainless steel GAS

Reduction of tee pieces

DN 15-12 20-10 20-15 25-12 25-15 25-20 32-20 32-25 40-25 40-32 50-25 50-32 50-40

Stainless steel

100

DN 15-12 20-10 20-12 20-15 25-12 25-15 25-20 32-12 32-15 32-20 32-25 40-12 40-15 40-20 40-25 40-32 50-12 50-15 50-20 50-25 50-32 50-40 65-40 65-50 80-50 80-65 100-50 100-65 100-80

Outer Ø 18-15 22-12 22-15 22-18 28-15 28-18 28-22 35-15 35-18 35-22 35-28 42-15 42-18 42-22 42-28 42-35 54-15 54-18 54-22 54-28 54-35 54-42 76-42 76,1-54 88,9-54 88,9-76,1 108-54 108-76,1 108-88,9

L2

L1 47,2 57,3 57,3 55,5 66,5 64,5 61,7 83,5 82,0 73,0 70,1 97,0 95,5 93,5 84,9 81,6 115,0 113,5 111,5 108,5 104,6 101,1 180,0 164,0 187,0 169,0 246,0 220,0 206,0

Z 36,5 39,5 39,5 39,5 44,5 44,5 44,5 51,0 51,0 51,0 51,0 60,0 60,0 60,0 60,0 60,0 71,0 71,0 71,0 71,0 71,0 71,0 116,0 116,0 131,0 131,0 156,0 156,0 156,0

Z1 30,7 38,8 38,8 37,0 45,0 43,0 40,2 58,5 57,0 48,0 45,1 67,0 65,5 63,5 54,9 51,6 79,0 77,5 75,5 72,5 68,6 65,1 119,0 103,0 119,0 101,0 167,0 141,0 127,0

16,5 18,5 18,5 18,5 21,5 21,5 21,5 25,0 25,0 25,0 25,0 30,0 30,0 30,0 30,0 30,0 36,0 36,0 36,0 36,0 36,0 36,0 61,0 61,0 68,0 68,0 79,0 79,0 79,0

Outer Ø 18-15 22-12 22-18 28-15 28-18 28-22 35-22 35-28 42-28 42-35 54-28 54-35 54-42

L2

L1 56,0 60,5 57,5 76,0 80,0 70,0 86,5 75,5 106,0 92,0 113,0 137,0 108,0

Z 39,0 41,5 41,5 46,0 46,0 46,0 50,5 50,5 59,0 59,0 71,0 71,0 71,0

Z1 37,0 40,0 37,0 53,0 57,0 47,0 62,0 51,0 77,0 63,0 77,0 101,0 72,0

19,0 20,5 20,5 23,0 23,0 23,0 24,5 24,5 29,0 29,0 36,0 36,0 36,0

101 Carbon steel DN 12-10 15-10 15-12 20-10 20-12 20-15 25-12 25-15 25-20 32-20 32-25 40-20 40-25 40-32 50-15 50-20 50-25 50-32 50-40 65-40 65-50 80-50 80-65 100-50 100-65 100-80

Outer Ø 15-12 18-12 18-15 22-12 22-15 22-18 28-15 28-18 28-22 35-22 35-28 42-22 42-28 42-35 54-18 54-22 54-28 54-35 54-42 76-42 76,1-54 88,9-54 88,9-76,1 108-54 108-76,1 108-88,9

L2

L1 53,0 53,3 48,5 58,7 56,9 57,5 65,5 63,8 63,5 72,0 71,0 89,0 86,0 80,0 113,0 104,0 100,0 99,0 97,0 181,0 170,0 190,0 170,0 216,0 216,0 204,0

Z 35,0 36,5 36,5 39,5 39,5 39,5 44,5 44,5 44,5 51,0 51,0 60,0 60,0 60,0 71,0 71,0 71,0 71,0 71,0 115,0 115,0 131,0 131,0 152,0 152,0 152,0

Z1 38,0 36,8 32,0 40,2 38,4 39,0 44,0 42,3 42,0 47,0 46,0 59,0 56,0 50,0 77,0 68,0 64,0 63,0 61,0 121,0 110,0 122,0 102,0 141,0 141,0 129,0

15,0 16,5 16,5 18,5 18,5 18,5 21,5 21,5 21,5 25,0 25,0 30,0 30,0 30,0 36,0 36,0 36,0 36,0 36,0 60,0 60,0 68,0 68,0 75,0 75,0 75,0

5 Reduction of tee pieces

Elbow 45˚ (2 x press) on elbow 45˚ (press x male)

Copper

102

DN 12-10 15-10 15-12 20-12 20-15 25-12 25-15 25-20 32-20 32-25 40-20 40-25 40-32 50-25 50-32 50-40 65-32 65-40 65-50 65-32 65-40 65-50 65-65 80-40 80-50 80-65 80-65 100-40 100-50 100-65 100-65 100-80

Outer Ø 15-12 18-12 18-15 22-15 22-18 28-15 28-18 28-22 35-22 35-28 42-22 42-28 42-35 54-28 54-35 54-42 64-35 64-42 64-54 76-35 76-42 76,1-54 76-64 89-42 88,9-54 89-64 88,9-76,1 108-42 108-54 108-64 108-76,1 108-88,9

L2

L1 39,5 43,6 38,5 50,0 42,0 61,0 56,0 53,4 71,4 67,6 83,0 75,5 76,0 101,0 97,0 91,8 167,0 170,0 163,0 155,0 154,0 149,0 149,0 205,0 197,0 197,5 190,0 216,0 212,0 204,0 204,0 197,5

Z 32,0 34,0 34,0 37,0 37,0 42,0 42,0 42,0 50,0 50,0 58,0 58,0 58,0 69,0 69,0 69,0 133,0 133,0 133,0 121,0 121,0 121,0 121,0 162,0 162,0 162,0 162,0 159,0 159,0 159,0 159,0 159,0

Z1 27,5 29,6 24,5 34,0 26,0 42,0 37,0 34,4 47,4 43,6 55,0 47,5 48,0 67,0 63,0 57,8 84,0 87,0 80,0 87,0 86,0 81,0 81,0 105,0 97,0 97,5 90,0 124,0 120,0 112,0 112,0 105,5

12,0 14,0 14,0 16,0 16,0 19,0 19,0 19,0 24,0 24,0 28,0 28,0 28,0 34,0 34,0 34,0 83,0 83,0 83,0 68,0 68,0 68,0 68,0 100,0 100,0 100,0 100,0 92,0 92,0 92,0 92,0 92,0

Stainless steel DN 12 15 20 25 32 40 50 65 80 100

Outer Ø 15 18 22 28 35 42 54 76,1 88,9 108

a

Z 33,9 35,8 40,0 44,4 50,8 62,9 73,8 113,1 127,3 152,0

Z1 54,9 60,0 68,4 78,8 91,8 115,5 137,6 199,1 225,3 274,0

Z2 10,5 12,1 14,2 17,2 20,5 26,3 31,9 43,0 49,0 61,0

103

b 10,5 12,1 14,2 17,2 20,5 26,3 31,9 43,0 49,0 61,0

33,9 35,8 40,0 44,4 50,8 62,9 73,8 113,1 127,3 152,0

Stainless steel GAS DN 12 15 20 25 32 40 50

Outer Ø 15 18 22 28 35 42 54

a

Z 43,8 46,0 51,6 59,4 70,7 87,7 103,2

Z1 75,8 80,0 95,6 113,4 130,7 167,7 199,2

Z2 16,0 17,0 22,0 27,0 28,0 38,0 46,0

b 16,0 17,0 22,0 27,0 32,0 42,0 50,0

43,8 46,0 51,6 59,4 70,7 87,7 103,2

Providing suitable solutions

5 Elbow 45˚ (2 x press) on elbow 45˚ (press x male)

2 x Elbow 45˚ (2 x press) with tube

Carbon steel DN 12 15 20 25 32 40 50 65 80 100

Outer Ø 15 18 22 28 35 42 54 76,1 88,9 108

a

Z 34,4 35,8 40,0 44,3 50,7 62,7 73,8 111,7 123,0 158,4

Z1 55,4 60,0 68,4 78,5 91,5 114,9 137,6 193,7 215,0 284,4

Z2 10,5 12,1 14,2 17,1 20,4 26,1 31,9 41,0 46,0 63,0

b 10,5 12,1 14,2 17,1 20,4 26,1 31,9 41,0 46,0 63,0

34,4 35,8 40,0 44,3 50,7 62,7 73,8 111,7 123,0 158,4

104

Stainless steel DN

Outer Ø

12 15 20 25 32 40 50 65 80 100

15 18 22 28 35 42 54 76,1 88,9 108

Copper DN 12 15 20 25 32 40 50 65 80 100

Outer Ø 15 18 22 28 35 42 54 64 76,1 88,9 108

a

Z 31,3 33,8 39,3 45,6 55,8 69,2 81,4 147,8 144,3 178,9 187,7

Z1 46,2 51,8 63,7 78,5 95,2 118,1 140,2 275,8 245,3 334,9 331,7

Z2 7,5 9,0 10,9 13,9 17,4 20,9 26,8 64,0 46,0 78,0 68,0

b 7,5 9,0 13,5 19,0 22,0 28,0 32,0 64,0 55,0 78,0 76,0

31,3 33,8 39,3 45,6 55,8 69,2 81,4 147,8 144,3 178,9 187,7

105

Tube length L-min a-min Z-min b z 50,0 50,2 71,2 50,2 50,0 52,5 76,7 52,5 52,0 56,9 85,3 56,9 56,0 63,9 98,3 63,9 62,0 72,8 113,8 72,8 80,0 93,8 146,4 93,8 90,0 108,8 172,6 108,8 150,0 166,9 252,9 166,9 176,0 193,7 291,7 193,7 204,0 230,5 352,5 230,5

10,5 12,1 14,2 17,2 20,5 26,3 31,9 43,0 49,0 61,0

Tube length L-min a-min Z-min b z 50,0 58,0 90,0 58,0 50,0 59,4 93,4 59,4 52,0 67,9 111,9 67,9 56,0 77,8 131,8 77,8 62,0 89,1 153,1 89,1 80,0 116,0 200,0 116,0 90,0 134,4 234,4 134,4

16,0 17,0 22,0 27,0 32,0 42,0 50,0

Stainless steel GAS DN 12 15 20 25 32 40 50

Outer Ø 15 18 22 28 35 42 54

Providing suitable solutions

5 2 x Elbow 45˚ (2 x press) with tube

Elbow 90˚ (2 x press) on elbow 90˚ (press x male)

Carbon steel

106

DN

Outer Ø

12 15 20 25 32 40 50 65 80 100

15 18 22 28 35 42 54 76,1 88,9 108

Tube length L-min a-min Z-min b z 50,0 50,2 71,2 50,2 50,0 52,5 76,7 52,5 52,0 56,9 85,3 56,9 56,0 63,8 98,0 63,8 62,0 72,7 113,5 72,7 80,0 93,5 145,7 93,5 90,0 108,8 172,6 108,8 150,0 164,0 246,0 164,0 176,0 189,5 281,5 189,5 204,0 233,3 359,3 233,3

10,5 12,1 14,2 17,1 20,4 26,1 31,9 41,0 46,0 63,0

Copper DN 12 15 20 25 32 40 50 65 80 100

Outer Ø 15 18 22 28 35 42 54 64 76,1 88,9 108

Tube length L-min 50 50 52 56 62 80 90 130 130 174 185

a-min Z-min b z 46,0 61,0 46,0 48,1 66,1 48,1 53,7 80,7 53,7 65,1 103,1 65,1 73,5 117,5 73,5 94,8 150,8 94,8 110,3 174,3 110,3 182,4 310,4 182,4 164,1 274,1 164,1 233,4 389,4 233,4 236,2 388,2 236,2

7,5 9,0 13,5 19,0 22,0 28,0 32,0 64,0 55,0 78,0 76,0

Stainless steel DN 12 15 20 25 32 40 50 65 80 100

Outer Ø 15 18 22 28 35 42 54 76,1 88,9 108

A

h 69,6 76,4 90,0 102,6 121,0 148,6 180,6 260,0 302,0 374,0

Z 48,6 51,4 60,0 65,5 75,9 92,5 110,6 165,0 190,0 238,0

107

z 42,0 50,0 60,0 74,2 90,2 112,2 140,0 190,0 224,0 273,0

21,0 25,0 30,0 37,1 45,1 56,1 70,0 95,0 112,0 136,0

Stainless steel GAS DN 12 15 20 25 32 40 50

Outer Ø 15 18 22 28 35 42 54

A

h 91,0 106,0 116,0 140,0 152,0 201,0 248,0

Z 64,0 72,0 76,0 91,0 92,0 119,0 145,0

z 54,0 68,0 80,0 98,0 120,0 164,0 206,0

27,0 34,0 40,0 49,0 60,0 82,0 103,0

Providing suitable solutions

5 Elbow 90˚ (2 x press) on elbow 90˚ (press x male)

2 x Elbow 90˚ (2 x press) with tube

Carbon steel

108

DN 10 12 15 20 25 32 40 50 65 80 100

Outer Ø 12 15 18 22 28 35 42 54 76,1 88,9 108

A

h 60,4 69,6 76,4 88,1 102,5 120,9 148,5 180,6 263,0 298,0 372,0

Z 42,4 48,6 51,4 58,1 65,5 75,9 92,5 110,6 167,0 188,0 235,0

z 36,0 42,0 50,0 60,0 74,0 90,0 112,0 140,0 192,0 220,0 274,0

18,0 21,0 25,0 30,0 37,0 45,0 56,0 70,0 96,0 110,0 137,0

Copper DN 10 12 15 20 25 32 40 50 65 80 100

Outer Ø 12 15 18 22 28 35 42 54 64 76,1 88,9 108

A

h 58,9 67,0 74,6 84,0 98,0 124,0 151,4 185,0 317,0 282,0 403,0 394,0

Z 44,5 50,0 53,0 58,0 64,0 82,0 101,0 120,0 195,0 190,0 250,0 259,0

z 28,8 33,0 43,2 53,0 68,0 86,0 102,4 131,0 244,0 190,0 306,0 276,0

14,4 17,0 21,6 26,0 34,0 42,0 50,4 65,0 122,0 92,0 153,0 135,0

Stainless steel DN 12 15 20 25 32 40 50 65 80 100

Outer Ø 15 18 22 28 35 42 54 76,1 88,9 108

A-min 92,0 100,0 112,0 130,2 152,2 192,2 230,0 340,0 400,0 478,0

L-min

Z 50,0 50,0 52,0 56,0 62,0 80,0 90,0 150,0 176,0 206,0

109

z 42,0 50,0 60,0 74,2 90,2 112,2 140,0 190,0 224,0 272,0

21,0 25,0 30,0 37,1 45,1 56,1 70,0 95,0 112,0 136,0

Stainless steel GAS DN 12 15 20 25 32 40 50

Outer Ø 15 18 22 28 35 42 54

A-min L-min Z 104,0 50,0 118,0 50,0 132,0 52,0 154,0 56,0 182,0 62,0 244,0 80,0 296,0 90,0

z 54,0 68,0 80,0 98,0 120,0 164,0 206,0

27,0 34,0 40,0 49,0 60,0 82,0 103,0

Providing suitable solutions

5 2 x Elbow 90˚ (2 x press) with tube

Elbow 90˚ (2 x press) on bend tube 90˚ (long side)

Carbon steel

110

DN 10 12 15 20 25 32 40 50 65 80 100

Outer Ø 12 15 18 22 28 35 42 54 76,1 88,9 108

A-min

L-min

80,0 92,0 100,0 112,0 130,0 152,0 192,0 230,0 342,0 396,0 478,0

Z 44,0 50,0 50,0 52,0 56,0 62,0 80,0 90,0 150,0 176,0 204,0

z 36,0 42,0 50,0 60,0 74,0 90,0 112,0 140,0 192,0 220,0 274,0

18,0 21,0 25,0 30,0 37,0 45,0 56,0 70,0 96,0 110,0 137,0

Copper DN 10 12 15 20 25 32 40 50 65 80 100

Outer Ø 12 15 18 22 28 35 42 54 64 76,1 88,9 108

A-min 72,8 84,0 93,2 104,0 124,0 146,0 180,8 220,0 374,0 324,0 480,0 455,0

L-min

Z 44,0 50,0 50,0 52,0 56,0 62,0 80,0 90,0 130,0 140,0 174,0 185,0

z 28,8 34,0 43,2 52,0 68,0 84,0 100,8 130,0 244,0 184,0 306,0 270,0

14,4 17,0 21,6 26,0 34,0 42,0 50,4 65,0 122,0 92,0 153,0 135,0

Stainless steel DN 12 15 20 25 32 40 50

Outer Ø 15 18 22 28 35 42 54

111 A/A-min z 141,0 145,0 150,0 157,1 245,1 306,1 370,0

21,0 25,0 30,0 37,1 45,1 56,1 70,0

h2/h2-min Z h1 h1-min 120,0 91,0 70,0 58,0 120,0 95,0 70,0 63,0 120,0 102,0 72,0 70,0 120,0 119,1 82,0 80,0 200,0 165,1 120,0 100,0 250,0 206,1 150,0 120,0 300,0 270,0 200,0 145,0

Stainless steel GAS DN 12 15 20 25 32 40 50

Outer Ø 15 18 22 28 35 42 54

A/A-min z h2/h2-min Z h1 h1-min 147,0 27,0 120,0 97,0 70,0 58,0 154,0 34,0 120,0 104,0 70,0 63,0 160,0 40,0 120,0 110,0 70,0 70,0 169,0 49,0 120,0 129,0 80,0 80,0 260,0 60,0 200,0 180,0 120,0 100,0 332,0 82,0 250,0 232,0 150,0 120,0 403,0 103,0 300,0 303,0 200,0 145,0

Providing suitable solutions

5 Elbow 90˚ (2 x press) on bend tube 90˚ (long side)

Elbow 90˚ (2 x press) on bend tube 90˚ (short side)

Carbon steel DN 10 12 15 20 25 32 40 50

Outer Ø 12 15 18 22 28 35 42 54

A/A-min z 138,0 141,0 145,0 150,0 157,0 245,0 306,0 370,0

18,0 21,0 25,0 30,0 37,0 45,0 56,0 70,0

h2/h2-min Z h1 h1-min 120,0 88,0 70,0 58,0 120,0 91,0 70,0 58,0 120,0 95,0 70,0 63,0 120,0 102,0 72,0 70,0 120,0 119,0 82,0 80,0 200,0 165,0 120,0 100,0 250,0 206,0 150,0 120,0 300,0 270,0 200,0 145,0 Stainless steel

112

Copper DN

Outer Ø

12 15 20 25 32

15 18 22 28 35

A/A-min 138,0 141,6 146,4 153,6 242,0

z

h2/h2-min 18,0 21,6 26,4 33,6 42,0

120,0 120,0 120,0 120,0 200,0

Z

h1 88,0 91,6 96,4 113,6 162,0

70,0 70,0 70,0 80,0 120,0

h1-min 58,0 63,0 70,0 80,0 100,0

DN 12 15 20 25 32 40 50

Outer Ø 15 18 22 28 35 42 54

A/A-min z 91,0 95,0 102,0 119,1 165,1 206,1 270,0

21,0 25,0 30,0 37,1 45,1 56,1 70,0

h2/h2-min Z h1 h1-min 70,0 141,0 120,0 58,0 70,0 145,0 120,0 63,0 72,0 150,0 120,0 70,0 82,0 157,1 120,0 80,0 120,0 245,1 200,0 100,0 150,0 306,1 250,0 120,0 200,0 370,0 300,0 145,0

Stainless steel GAS DN 12 15 20 25 32 40 50

Outer Ø 15 18 22 28 35 42 54

A/A-min z h2/h2-min Z h1 h1-min 97,0 27,0 70,0 147,0 120,0 58,0 104,0 34,0 70,0 154,0 120,0 63,0 110,0 40,0 70,0 160,0 120,0 70,0 129,0 49,0 80,0 169,0 120,0 80,0 180,0 60,0 120,0 260,0 200,0 100,0 232,0 82,0 150,0 332,0 250,0 120,0 303,0 103,0 200,0 403,0 300,0 145,0

Providing suitable solutions

113

5 Elbow 90˚ (2 x press) on bend tube 90˚ (short side)

Elbow 45˚ (press x female) on tee lateral

Carbon steel DN 10 12 15 20 25 32 40 50

114

Outer Ø 12 15 18 22 28 35 42 54

A/A-min z 88,0 91,0 95,0 102,0 119,0 165,0 206,0 270,0

18,0 21,0 25,0 30,0 37,0 45,0 56,0 70,0

h2/h2-min Z h1 h1-min 70,0 138,0 120,0 58,0 70,0 141,0 120,0 58,0 70,0 145,0 120,0 63,0 72,0 150,0 120,0 70,0 82,0 157,0 120,0 80,0 120,0 245,0 200,0 100,0 150,0 306,0 250,0 120,0 200,0 370,0 300,0 145,0

Copper DN 12 15 20 25 32

Outer Ø 15 18 22 28 35

A/A-min z h2/h2-min Z h1 h1-min 88,0 18,0 70,0 138,0 120,0 58,0 91,6 21,6 70,0 141,6 120,0 63,0 96,4 26,4 70,0 146,4 120,0 70,0 113,6 33,6 80,0 153,6 120,0 80,0 162,0 42,0 120,0 242,0 200,0 100,0

Stainless steel DN 12 15 20 25 32 40 50 65 80 100

Outer Ø 15 18 22 28 35 42 54 76,1 88,9 108

Z

z 50,5 53,8 60,0 67,5 77,3 92,8 109,7 168,2 186,9 225,0

A 10,5 12,1 14,2 17,2 20,5 26,3 31,9 43,0 49,0 61,0

z2 40,0 41,7 45,8 50,3 56,8 66,5 77,8 125,2 137,9 164,0

D 19,0 20,5 22,5 25,5 29,0 31,5 37,5 60,0 64,0 78,0

40,0 41,7 45,8 50,3 56,8 66,5 77,8 125,2 137,9 164,0

Stainless steel GAS DN 12 15 20 25 32 40 50

Outer Ø 15 18 22 28 35 42 54

Z

z 58,4 64,4 71,5 84,3 95,9 117,2 139,3

A 16,0 17,0 22,0 27,0 28,0 38,0 46,0

z2 42,4 47,4 49,5 57,3 67,9 79,2 93,3

D 14,0 19,0 19,0 24,0 28,0 30,0 36,0

42,4 47,4 49,5 57,3 67,9 79,2 93,3

Providing suitable solutions

115

5 Elbow 45˚ (press x female) on tee lateral

Elbow 45˚ (2 x press) on tube on tee lateral

Carbon steel

116

DN 12 15 20 25 32 40 50 65 80 100

Outer Ø 15 18 22 28 35 42 54 76,1 88,9 108

Z 58,4 61,3 67,5 74,8 84,7 99,2 116,3 177,7 186,0 233,4

z 24,0 25,5 27,5 30,5 34,0 36,5 42,5 66,0 63,0 75,0

A

z2 34,4 35,8 40,0 44,3 50,7 62,7 73,8 111,7 123,0 158,4

D 10,5 12,1 14,2 17,1 20,4 26,1 31,9 41,0 46,0 63,0

34,4 35,8 40,0 44,3 50,7 62,7 73,8 111,7 123,0 158,4

Copper DN 12 15 20 25 32 40 50 65 80 100

Outer Ø 15 18 22 28 35 42 54 64 76,1 88,9 108

Z

z 41,9 46,3 53,0 60,2 75,3 90,8 108,9 225,9 200,2 272,5 268,1

A 7,5 9,0 10,9 13,9 17,4 20,9 26,8 64,0 46,0 78,0 68,0

z2 34,4 37,3 42,1 46,3 57,9 69,9 82,1 161,9 154,2 194,5 200,1

D 12,0 14,0 16,0 19,0 24,0 28,0 34,0 84,0 65,0 100,0 92,0

34,4 37,3 42,1 46,3 57,9 69,9 82,1 161,9 154,2 194,5 200,1

Stainless steel DN 12 15 20 25 32 40 50 65 80 100

Outer Ø 15 18 22 28 35 42 54 76,1 88,9 108

Z

z 66,7 70,5 76,9 87,0 99,3 123,7 144,6 221,9 253,4 303,5

A 10,5 12,1 14,2 17,2 20,5 26,3 31,9 43,0 49,0 61,0

56,2 58,4 62,7 69,8 78,8 97,4 112,7 178,9 204,4 242,5

L-min z2 b-min 50,0 19,0 56,2 50,0 20,5 58,4 52,0 22,5 62,7 56,0 25,5 69,8 62,0 29,0 78,8 80,0 31,5 97,4 90,0 37,5 112,7 150,0 60,0 178,9 176,0 64,0 204,4 204,0 78,0 242,5

56,6 60,8 65,8 75,7 86,3 107,5 124,5

L-min z2 b-min 50,0 14,0 56,6 50,0 19,0 60,8 52,0 19,0 65,8 56,0 24,0 75,7 62,0 28,0 86,3 80,0 30,0 107,5 90,0 36,0 124,5

Stainless steel GAS DN 12 15 20 25 32 40 50

Outer Ø 15 18 22 28 35 42 54

Z

z 72,6 77,8 87,8 102,7 118,3 149,5 174,5

A 16,0 17,0 22,0 27,0 32,0 42,0 50,0

Providing suitable solutions

117

5 Elbow 45˚ (2 x press) on tube on tee lateral

Elbow 90˚ (press x female) on tee lateral

Carbon steel DN 12 15 20 25 32 40 50 65 80 100

Outer Ø 15 18 22 28 35 42 54 76,1 88,9 108

Z

z 70,3 74,0 80,5 90,4 102,7 126,9 148,1 222,7 247,5 304,8

A 10,5 12,1 14,2 17,1 20,4 26,1 31,9 41,0 46,0 63,0

59,8 61,9 66,3 73,3 82,3 100,8 116,2 181,7 201,5 241,8

L-min z2 b-min 50,0 24,0 59,8 50,0 25,5 61,9 52,0 27,5 66,3 56,0 30,5 73,3 62,0 34,0 82,3 80,0 36,5 100,8 90,0 42,5 116,2 150,0 66,0 181,7 176,0 63,0 201,5 204,0 75,0 241,8

118 Copper DN 12 15 20 25 32 40 50 65 80 100

Outer Ø 15 18 22 28 35 42 54 64 76,1 88,9 108

Z

z 56,6 60,6 71,1 85,5 98,4 124,2 142,3 260,6 238,9 326,9 325,6

A 7,5 9,0 13,5 19,0 22,0 28,0 32,0 64,0 55,0 78,0 76,0

49,1 51,6 57,6 66,5 76,4 96,2 110,3 196,6 183,9 248,9 249,6

L-min z2 b-min 50,0 12,0 49,1 50,0 14,0 51,6 52,0 16,0 57,6 56,0 19,0 66,5 62,0 24,0 76,4 80,0 28,0 96,2 90,0 34,0 110,3 130,0 84,0 196,6 140,0 65,0 183,9 174,0 100,0 248,9 185,0 92,0 249,6

Stainless steel DN 12 15 20 25 32 40 50 65 80 100

Outer Ø 15 18 22 28 35 42 54 76,1 88,9 108

M/M-min z2 67,6 71,9 82,5 91,0 104,9 124,0 148,1 225,0 254,0 316,0

19,0 20,5 22,5 25,5 29,0 31,5 37,5 60,0 64,0 78,0

h

M/M-min z2 78,0 91,0 95,0 115,0 120,0 149,0 181,0

14,0 19,0 19,0 24,0 28,0 30,0 36,0

Z 48,6 51,4 60,0 65,5 75,9 92,5 110,6 165,0 190,0 238,0

21,0 25,0 30,0 37,1 45,1 56,1 70,0 95,0 112,0 137,0

Stainless steel GAS DN 12 15 20 25 32 40 50

Outer Ø 15 18 22 28 35 42 54

h

Z 64,0 72,0 76,0 91,0 92,0 119,0 145,0

27,0 34,0 40,0 49,0 60,0 82,0 103,0

Providing suitable solutions

119

5 Elbow 90˚ (press x female) on tee lateral

Elbow 90˚ (2 x press) on tube on tee lateral

Carbon steel

120

DN 10 12 15 20 25 32 40 50 65 80 100

Outer Ø 12 15 18 22 28 35 42 54 76,1 88,9 108

M/M-min z2 64,9 72,6 76,9 85,6 96,0 109,9 129,0 153,1 233,0 251,0 310,0

22,5 24,0 25,5 27,5 30,5 34,0 36,5 42,5 66,0 63,0 75,0

h

Outer Ø 12 15 18 22 28 35 42 54 64 76,1 88,9 108

M/M-min z2 55,5 62,0 67,0 74,0 83,0 106,0 129,0 154,0 279,0 255,0 350,0 351,0

11,0 12,0 14,0 16,0 19,0 24,0 28,0 34,0 84,0 65,0 100,0 92,0

Z 42,4 48,6 51,4 58,1 65,5 75,9 92,5 110,6 167,0 188,0 235,0

18,0 21,0 25,0 30,0 37,0 45,0 56,0 70,0 96,0 110,0 137,0

Copper DN 10 12 15 20 25 32 40 50 65 80 100

h

Z 44,5 50,0 53,0 58,0 64,0 82,0 101,0 120,0 195,0 190,0 250,0 259,0

14,4 16,0 21,6 27,0 34,0 44,0 52,0 66,0 122,0 98,0 153,0 141,0

Stainless steel DN 12 15 20 25 32 40 50 65 80 100

Outer Ø 15 18 22 28 35 42 54 76,1 88,9 108

M-min 69,0 70,5 74,5 81,5 91,0 111,5 127,5 210,0 240,0 283,0

L-min

z2 50,0 50,0 52,0 56,0 62,0 80,0 90,0 150,0 176,0 205,0

Z 19,0 20,5 22,5 25,5 29,0 31,5 37,5 60,0 64,0 78,0

21,0 25,0 30,0 37,1 45,1 56,1 70,0 95,0 112,0 136,0

Stainless steel GAS DN 12 15 20 25 32 40 50

Outer Ø 15 18 22 28 35 42 54

M-min 64,0 69,0 71,0 80,0 90,0 110,0 126,0

L-min 50,0 50,0 52,0 56,0 62,0 80,0 90,0

z2 14,0 19,0 19,0 24,0 28,0 30,0 36,0

Z 27,0 34,0 40,0 49,0 60,0 82,0 103,0

Providing suitable solutions

121

5 Elbow 90˚ (2 x press) on tube on tee lateral

Elbow 90˚ (2 x press) on elbow 45° (press x female) offset

Carbon steel

122

DN 10 12 15 20 25 32 40 50 65 80 100

Outer Ø 12 15 18 22 28 35 42 54 76,1 88,9 108

M-min

Outer Ø 12 15 18 22 28 35 42 54 64 76,1 88,9 108

M-min

L-min

84,5 95,0 100,5 109,5 123,5 141,0 172,5 202,5 312,0 349,0 416,0

z2 44,0 50,0 50,0 52,0 56,0 62,0 80,0 90,0 150,0 176,0 204,0

Z 22,5 24,0 25,5 27,5 30,5 34,0 36,5 42,5 66,0 63,0 75,0

18,0 21,0 25,0 30,0 37,0 45,0 56,0 70,0 96,0 110,0 137,0

Copper DN 10 12 15 20 25 32 40 50 65 80 100

55,0 62,0 64,0 68,0 75,0 86,0 108,0 124,0 214,0 205,0 274,0 277,0

L-min

z2 44,0 50,0 50,0 52,0 56,0 62,0 80,0 90,0 130,0 140,0 174,0 185,0

Z 11,0 12,0 14,0 16,0 19,0 24,0 28,0 34,0 84,0 65,0 100,0 92,0

14,4 17,0 21,6 26,0 34,0 42,0 50,4 65,0 122,0 92,0 153,0 135,0

Stainless steel DN 12 15 20 25 32 40 50 65 80 100

Outer Ø 15 18 22 28 35 42 54 76,1 88,9 108

Z

A 51,9 57,0 65,3 75,7 88,7 110,2 132,7 192,9 220,8 266,1

41,4 44,9 51,1 58,5 68,2 83,9 100,8 149,9 171,8 205,1

z 45˚ b z 10,5 41,4 12,1 44,9 14,2 51,1 17,2 58,5 20,5 68,2 26,3 83,9 31,9 100,8 43,0 149,9 49,0 171,8 61,0 205,1

21,0 25,0 30,0 37,1 45,1 56,1 70,0 95,0 112,0 136,0

51,6 58,0 64,3 75,0 90,5 116,0 140,7

z 45˚ b z 16,0 51,6 17,0 58,0 22,0 64,3 27,0 75,0 28,0 90,5 38,0 116,0 46,0 140,7

27,0 34,0 40,0 49,0 60,0 82,0 103,0

Stainless steel GAS DN 12 15 20 25 32 40 50

Outer Ø 15 18 22 28 35 42 54

Z

A 67,6 75,0 86,3 102,0 118,5 154,0 186,7

Providing suitable solutions

123

5 Elbow 90˚ (2 x press) on elbow 45° (press x female) offset

Elbow 90˚ (2 x press) on tube on elbow 45° (2 x press) offset

Carbon steel

124

DN 12 15 20 25 32 40 50 65 80 100

Outer Ø 15 18 22 28 35 42 54 76,1 88,9 108

Z

A 52,3 57,0 65,3 75,5 88,5 110,0 132,7 191,6 214,3 273,7

41,8 44,9 51,1 58,4 68,1 83,9 100,8 150,6 168,3 210,7

z 45˚ b z 10,5 41,8 12,1 44,9 14,2 51,1 17,1 58,4 20,4 68,1 26,1 83,9 31,9 100,8 41,0 150,6 46,0 168,3 63,0 210,7

21,0 25,0 30,0 37,0 45,0 56,0 70,0 96,0 110,0 137,0

Copper DN 12 15 20 25 32 40 50 65 80 100

Outer Ø 15 18 22 28 35 42 54 64 76,1 88,9 108

Z

A 45,5 51,7 60,1 70,8 88,0 106,7 130,8 252,8 219,2 309,9 298,5

z 45˚ 38,0 42,7 49,2 56,9 70,6 85,8 104,0 188,8 173,2 231,9 230,5

7,5 9,0 10,9 13,9 17,4 20,9 26,8 64,0 46,0 78,0 68,0

b

z 38,0 42,7 49,2 56,9 70,6 85,8 104,0 188,8 173,2 231,9 230,5

17,0 21,6 26,0 34,0 42,0 50,4 65,0 122,0 92,0 153,0 135,0

Stainless steel DN 12 15 20 25 32 40 50 65 80 100

Outer Ø 15 18 22 28 35 42 54 76,1 88,9 108

Z-min A-min z 45˚ L-min z b-min 68,1 57,6 10,5 50,0 21,0 57,6 73,7 61,6 12,1 50,0 25,0 61,6 82,2 68,0 14,2 52,0 30,0 68,0 95,2 78,0 17,2 56,0 37,1 78,0 110,7 90,2 20,5 62,0 45,1 90,2 141,1 114,8 26,3 80,0 56,1 114,8 167,6 135,7 31,9 90,0 70,0 135,7 246,6 203,6 43,0 150,0 95,0 203,6 287,3 238,3 49,0 176,0 112,0 238,3 345,3 284,3 61,0 205,0 136,0 284,3

Stainless steel GAS DN 12 15 20 25 32 40 50

Outer Ø 15 18 22 28 35 42 54

Z-min A-min z 45˚ L-min z b-min 81,8 65,8 16,0 50,0 27,0 65,8 88,4 71,4 17,0 50,0 34,0 71,4 102,6 80,6 22,0 52,0 40,0 80,6 120,3 93,3 27,0 56,0 49,0 93,3 140,9 108,9 32,0 62,0 60,0 108,9 186,2 144,2 42,0 80,0 82,0 144,2 221,8 171,8 50,0 90,0 103,0 171,8

Providing suitable solutions

125

6.1 Elbow 90˚ (2 x press) on tube on elbow 45° (2 x press) offset Carbon steel

126

DN 12 15 20 25 32 40 50 65 80 100

Outer Ø 15 18 22 28 35 42 54 76,1 88,9 108

Z-min A-min z 45˚ L-min z b-min 68,1 57,6 10,5 50,0 21,0 57,6 73,7 61,6 12,1 50,0 25,0 61,6 82,2 68,0 14,2 52,0 30,0 68,0 95,0 77,9 17,1 56,0 37,0 77,9 110,5 90,1 20,4 62,0 45,0 90,1 140,7 114,6 26,1 80,0 56,0 114,6 167,6 135,7 31,9 90,0 70,0 135,7 243,9 202,9 41,0 150,0 96,0 202,9 280,8 234,8 46,0 176,0 110,0 234,8 348,7 285,7 63,0 204,0 137,0 285,7

Outer Ø 15 18 22 28 35 42 54 64 76,1 88,9 108

Z-min A-min z 45˚ L-min z b-min 60,2 52,7 7,5 50,0 17,0 52,7 66,0 57,0 9,0 50,0 21,6 57,0 78,2 64,7 13,5 52,0 26,0 64,7 96,, 77,1 19,0 56,0 34,0 77,1 111,1 89,1 22,0 62,0 42,0 89,1 140,0 112,0 28,0 80,0 50,4 112,0 164,2 132,2 32,0 90,0 65,0 132,2 287,5 223,5 64,0 130,0 122,0 223,5 257,9 202,9 55,0 140,0 92,0 202,9 364,4 286,4 78,0 174,0 153,0 286,4 356,0 280,0 76,0 185,0 135,0 280,0

VSH 6 Product range 127

Copper DN 12 15 20 25 32 40 50 65 80 100

6.1 XPress stainless steel

Providing suitable solutions

Stainless steel

6.1

R 2750  Stainless steel tube 1.4401 (AISI 316)

R 2753  Stainless steel tube 1.4520 (AISI 439)

(6m length)

(6m length) Dimension 15 x 1,0 18 x 1,0 22 x 1,2 28 x 1,2 35 x 1,5 42 x 1,5 54 x 1,5 76,1 x 2,0 88,9 x 2,0 108 x 2,0

DN 12 15 20 25 32 40 50 65 80 100

Article No. 611791.4 611792.5 611793.6 611794.7 611795.8 611796.9 611797.1 611798.0 611799.1 611800.2

Dimension 15 x 1,0 18 x 1,0 22 x 1,2 28 x 1,2 35 x 1,5 42 x 1,5 54 x 1,5

DN 12 15 20 25 32 40 50

Article No. 619300.0 619301.1 619302.2 619303.3 619304.4 619305.5 619306.6

128

129

R 2752  Stainless steel tube 1.4521 (AISI 444) (6m length) Dimension 15 x 1,0 18 x 1,0 22 x 1,2 28 x 1,2 35 x 1,5 42 x 1,5 54 x 1,5

DN 12 15 20 25 32 40 50

Article No. 619310.1 619311.0 619312.1 619313.2 619314.3 619315.4 619316.5

Providing suitable solutions

Stainless steel

130

6.1

R 2701 Straight coupling

R 2703 Slip coupling

(2 x press)

(2 x press)

Dimension 15 x 15 18 x 18 22 x 22 28 x 28 35 x 35 42 x 42 54 x 54 76,1 x 76,1 88,9 x 88,9 108 x 108

Article No. 619094.3 619095.4 619096.5 619097.6 619098.7 619099.8 619100.9 620415.4 620416.5 620417.6

L 50,0 50,0 52,0 56,2 62,3 73,3 83,0 142,0 163,0 192,0

Z 10,0 10,0 10,0 10,2 10,3 13,3 13,0 32,0 37,0 38,0

Dimension 15 x 15 18 x 18 22 x 22 28 x 28 35 x 35 42 x 42 54 x 54 76,1 x 76,1 88,9 x 88,9 108 x 108

Article No. 619128.4 619129.5 619130.6 619131.7 619132.8 619133.9 619134.1 620428.6 620429.7 620430.8

L 80,0 80,0 84,0 91,2 102,2 120,3 140,0 230,0 258,0 305,0

es 25,0 25,0 25,0 30,0 30,0 40,0 40,0 60,0 70,0 80,0

Providing suitable solutions

131

Stainless steel

132

6.1

R 2708 Elbow 90°

R 2711 Elbow 90°

(2 x press)

(press x male)

Dimension 15 x 15 18 x 18 22 x 22 28 x 28 35 x 35 42 x 42 54 x 54 76,1 x 76,1 88,9 x 88,9 108 x 108

Article No. 619020.6 619021.7 619022.8 619023.9 619024.1 619025.0 619026.1 623000.4 623001.5 623002.6

L

Z

41,0 45,0 51,0 60,1 71,1 86,1 105,0 150,0 175,0 214,0

21,0 25,0 30,0 37,1 45,1 56,1 70,0 95,0 112,0 136,0

Dimension 15 x Ø15 18 x Ø18 22 x Ø22 28 x Ø28 35 x Ø35 42 x Ø42 54 x Ø54 76,1 x Ø76,1 88,9 x Ø88,9 108 x Ø108

Article No. 619034.9 619035.1 619036.0 619037.1 619038.2 619039.3 619040.4 623003.7 623004.8 623005.9

L 41,0 45,0 51,0 60,1 71,1 86,1 105,0 150,0 174,0 216,0

Z 21,0 25,0 30,0 37,1 45,1 56,1 70,0 95,0 110,0 138,0

H 48,6 51,4 60,0 65,5 75,9 92,5 110,6 165,0 190,0 238,0

Providing suitable solutions

133

Stainless steel

134

R 2713 Elbow 45°

R 2712 Elbow 45°

(2 x press)

(press x male)

Dimension 15 x 15 18 x 18 22 x 22 28 x 28 35 x 35 42 x 42 54 x 54 76,1 x 76,1 88,9 x 88,9 108 x 108

Article No. 619004.1 619005.2 619006.3 619007.4 619008.5 619009.6 619010.7 623006.1 623007.0 623008.1

L 30,5 32,1 35,2 40,2 46,5 56,3 66,9 98,0 112,0 138,0

Z 10,5 12,1 14,2 17,2 20,5 26,3 31,9 43,0 49,0 61,0

Dimension 15 x Ø15 18 x Ø18 22 x Ø22 28 x Ø28 35 x Ø35 42 x Ø42 54 x Ø54 76,1 x Ø76,1 88,9 x Ø88,9 108 x Ø108

Article No. 619011.8 619012.9 619013.1 619014.0 619015.1 619016.2 619017.3 623009.2 623010.3 623011.4

6.1

L 30,5 32,1 35,2 40,2 46,5 56,3 66,9 98,0 112,0 138,0

Z 10,5 12,1 14,2 17,2 20,5 26,3 31,9 43,0 49,0 61,0

H 37,5 38,5 42,3 45,6 51,3 62,6 72,5 117,0 131,0 154,0

Providing suitable solutions

135

Stainless steel

136

R 2725 Bend 90°

R 2723 Bend 30°

(2 x male)

(2 x male)

Dimension Ø15 x Ø15 Ø18 x Ø18 Ø22 x Ø22 Ø28 x Ø28 Ø35 x Ø35 Ø42 x Ø42 Ø54 x Ø54

Article No. 619027.2 619028.3 619029.4 619030.5 619031.6 619032.7 619033.8

h2 120,0 120,0 120,0 120,0 200,0 250,0 300,0

h2min 58,0 63,0 70,0 80,0 100,0 120,0 145,0

h1 70,0 70,0 72,0 82,0 120,0 150,0 200,0

h1min 58,0 63,0 70,0 80,0 100,0 120,0 145,0

Dimension Ø28 x Ø28 Ø35 x Ø35 Ø42 x Ø42 Ø54 x Ø54

Article No. 619002.1 619003.0 619185.6 619186.7

6.1

h2 130,0 214,0 272,0 326,0

h2min 54,0 60,0 69,0 79,0

h1 51,0 80,0 99,0 134,0

h1min 51,0 60,0 69,0 79,0

R 2722 Bend 15° (2 x male)

R 2724 Bend 60° (2 x male)

Dimension Ø28 x Ø28 Ø35 x Ø35 Ø42 x Ø42 Ø54 x Ø54

Article No. 619018.4 619019.5 619187.8 619188.9

h2 121,0 203,0 256,0 306,0

h2min 66,0 77,0 90,0 107,0

h1 63,0 97,0 120,0 162,0

h1min 63,0 77,0 90,0 107,0

Dimension Ø28 x Ø28 Ø35 x Ø35 Ø42 x Ø42 Ø54 x Ø54

Article No. 619000.8 619001.9 619183.4 619184.5

h2 134,0 222,0 280,0 337,0

h2min 48,0 53,0 59,0 67,0

h1 45,0 73,0 89,0 122,0

h1min 45,0 53,0 59,0 67,0

Providing suitable solutions

137

Stainless steel

138

R 2717 Crossover

R 2714 Tee equal

(2 x male)

(3 x press)

Dimension Ø15 x Ø15 Ø18 x Ø18 Ø22 x Ø22 Ø28 x Ø28

Article No. 619108.6 619109.7 619110.8 619111.9

A 158,0 165,0 178,0 210,0

B 37,0 40,0 44,0 50,0

L 57,0 60,0 65,0 74,0

Dimension Article No. L1 15 x 15 x 15 619135.0 35,0 18 x 18 x 18 619137.2 36,5 22 x 22 x 22 619140.5 39,5 28 x 28 x 28 619144.9 44,5 35 x 35 x 35 619149.3 51,0 42 x 42 x 42 619153.7 60,0 54 x 54 x 54 619158.1 71,0 76,1 x 76,1 x 76,1 620431.9 116,0 88,9 x 88,9 x 88,9 620432.1 131,0 108 x 108 x 108 620433.0 156,0

6.1

Z1 15,0 16,5 18,5 21,5 25,0 30,0 36,0 61,0 68,0 79,0

L2 39,0 40,5 43,5 48,5 55,0 61,5 72,5 115,0 127,0 155,0

Z2 19,0 20,5 22,5 25,5 29,0 31,5 37,5 60,0 64,0 78,0

Providing suitable solutions

139

Stainless steel

R 2715 Tee reduced (3 x press)

140

Dimension 18 x 15 x 18 22 x 15 x 22 22 x 18 x 22 28 x 15 x 28 28 x 18 x 28 28 x 22 x 28 35 x 15 x 35 35 x 18 x 35 35 x 22 x 35 35 x 28 x 35 42 x 22 x 42 42 x 28 x 42 42 x 35 x 42 54 x 22 x 54 54 x 28 x 54 54 x 35 x 54 54 x 42 x 54 76,1 x 22 x 76,1 76,1 x 28 x 76,1 76,1 x 35 x 76,1 76,1 x 42 x 76,1 76,1 x 54 x 76,1

Article No. L1 619136.1 36,5 619138.3 39,5 619139.4 39,5 619141.6 44,5 619142.7 44,5 619143.8 44,5 619145.1 51,0 619146.0 51,0 619147.1 51,0 619148.2 51,0 619150.4 60,0 619151.5 60,0 619152.6 60,0 619154.8 71,0 619155.9 71,0 619156.1 71,0 619157.0 71,0 620434.1 116,0 620435.2 116,0 620436.3 116,0 620437.4 116,0 620438.5 116,0

Z1 16,5 18,5 18,5 21,5 21,5 21,5 25,0 25,0 25,0 25,0 30,0 30,0 30,0 36,0 36,0 36,0 36,0 61,0 61,0 61,0 61,0 61,0

L2 40,5 42,5 42,5 45,5 45,5 46,5 49,0 49,0 50,0 52,0 52,5 54,5 57,5 58,5 60,5 63,5 67,5 68,0 71,0 75,0 79,0 80,0

Z2 20,5 22,5 22,5 25,5 25,5 25,5 29,0 29,0 29,0 29,0 31,5 31,5 31,5 37,5 37,5 37,5 37,5 45,0 47,0 48,0 47,0 43,0

Dimension 88,9 x 22 x 88,9 88,9 x 28 x 88,9 88,9 x 35 x 88,9 88,9 x 42 x 88,9 88,9 x 54 x 88,9 88,9 x 76,1 x 88,9 108 x 22 x 108 108 x 28 x 108 108 x 35 x 108 108 x 42 x 108 108 x 54 x 108 108 x 76,1 x 108 108 x 88,9 x 108

6.1 Article No. 620439.6 620440.7 620441.8 620442.9 620443.1 620444.0 620445.1 620446.2 620447.3 620448.4 620449.5 620450.6 620451.7

L1 131,0 131,0 131,0 131,0 131,0 131,0 156,0 156,0 156,0 156,0 156,0 156,0 156,0

Z1 68,0 68,0 68,0 68,0 68,0 68,0 79,0 79,0 79,0 79,0 79,0 79,0 79,0

L2 76,0 76,0 83,0 85,0 93,0 116,0 85,0 88,0 94,0 96,0 102,0 125,0 135,0

Z2 53,0 52,0 56,0 53,0 56,0 61,0 62,0 64,0 67,0 64,0 65,0 70,0 72,0

141

Providing suitable solutions

Stainless steel

142

6.1

R 2718 Tee threaded

R 2707 Reducer

(press x female thread x press)

(male x press)

Dimension 15 x Rp1/2 x 15 18 x Rp1/2 x 18 18 x Rp3/4 x 18 22 x Rp1/2 x 22 22 x Rp3/4 x 22 28 x Rp1/2 x 28 28 x Rp3/4 x 28 28 x Rp1 x 28 35 x Rp1/2 x 35 35 x Rp3/4 x 35 35 x Rp1 x 35 42 x Rp1/2 x 42 42 x Rp3/4 x 42 42 x Rp1 x 42 54 x Rp1/2 x 54 54 x Rp3/4 x 54 54 x Rp1 x 54 54 x Rp2 x 54 76,1 x Rp3/4 x 76,1 76,1 x Rp2 x 76,1 88,9 x Rp3/4 x 88,9 88,9 x Rp2 x 88,9 108 x Rp3/4 x 108 108 x Rp2 x 108

Article No. L1 619159.2 35,0 619160.3 36,5 619161.4 36,5 619162.5 39,5 619163.6 39,5 619164.7 44,5 619165.8 44,5 619859.9 44,5 619166.9 51,0 619167.1 51,0 619860.1 51,0 619168.0 60,0 619169.1 60,0 619861.0 60,0 619170.2 71,0 619172.4 71,0 619862.1 71,0 619171.3 71,0 620452.8 116,0 620455.0 116,0 620453.9 131,0 620456.1 131,0 620454.1 156,0 620457.2 156,0

Z1 15,0 16,5 16,5 18,5 18,5 21,5 21,5 21,5 25,0 25,0 25,0 30,0 30,0 30,0 36,0 36,0 36,0 36,0 55,0 55,0 63,0 63,0 77,0 77,0

L2 34,3 35,0 37,0 37,0 39,0 40,0 42,0 46,0 43,5 45,5 50,0 46,0 48,0 52,5 52,0 54,0 58,0 64,7 68,0 81,0 87,0 88,0 86,0 98,0

Z2 24,3 25,0 26,0 27,0 28,0 30,0 31,0 27,5 33,5 34,5 31,0 36,0 37,0 33,5 42,0 43,0 38,0 46,7 55,0 59,0 74,0 66,0 73,0 76,0

Dimension Ø18 x 15 Ø22 x 15 Ø22 x 18 Ø28 x 15 Ø28 x 18 Ø28 x 22 Ø35 x 15 Ø35 x 18 Ø35 x 22 Ø35 x 28 Ø42 x 15 Ø42 x 18 Ø42 x 22 Ø42 x 28 Ø42 x 35 Ø54 x 15 Ø54 x 18 Ø54 x 22 Ø54 x 28 Ø54 x 35 Ø54 x 42 Ø76,1 x 42 Ø76,1 x 54 Ø88,9 x 54 Ø88,9 x 76,1 Ø108 x 54 Ø108 x 76,1 Ø108 x 88,9

Article No. 619112.1 619113.0 619114.1 619115.2 619116.3 619117.4 619222.1 619118.5 619119.6 619120.7 619223.0 619224.1 619121.8 619122.9 619123.1 619225.2 619226.3 619124.0 619125.1 619126.2 619127.3 620421.1 620422.0 620423.1 620424.2 620425.3 620426.4 620427.5

L

Z 50,7 58,8 57,0 65,0 63,0 61,2 78,5 77,0 69,0 68,1 87,0 85,5 84,5 77,9 77,6 99,0 97,5 96,5 95,5 94,6 95,1 151,0 140,0 156,0 156,0 204,0 196,0 196,0

30,7 38,8 37,0 45,0 43,0 40,2 58,5 57,0 48,0 45,1 67,0 65,5 63,5 54,9 51,6 79,0 77,5 75,5 72,5 68,6 65,1 119,0 103,0 119,0 101,0 167,0 141,0 127,0 Providing suitable solutions

143

Stainless steel

144

6.1

R 2705 Straight connector

R 2702 Straight connector

(press x male thread)

(press x female thread)

Dimension 15 x R1/2 15 x R3/4 18 x R1/2 18 x R3/4 22 x R1/2 22 x R3/4 22 x R1 28 x R3/4 28 x R1 28 x R1 1/4 35 x R1 35 x R1 1/4 35 x R1 1/2 42 x R1 1/4 42 x R1 1/2 54 x R1 1/2 54 x R2 76,1 x R2 1/2 88,9 x R3

Article No. 619058.0 619059.1 619060.2 619061.3 619063.5 619064.6 619062.4 619067.9 619065.7 619066.8 619068.1 619070.1 619069.0 619072.3 619071.2 619073.4 619074.5 620475.9 620476.1

L 38,0 41,0 38,0 41,0 42,0 43,3 48,5 45,2 48,0 51,5 52,7 55,0 56,0 59,0 59,0 64,7 69,0 125,0 138,0

Z 18,0 21,0 18,0 21,0 21,0 22,3 27,5 22,2 25,0 28,5 26,7 29,0 30,0 29,0 29,0 29,7 34,0 70,0 75,0

Dimension 15 x Rp1/2 15 x Rp3/4 18 x Rp1/2 18 x Rp3/4 22 x Rp1/2 22 x Rp3/4 22 x Rp1 28 x Rp1/2 28 x Rp3/4 28 x Rp1 28 x Rp1 1/4 35 x Rp1 35 x Rp1 1/4 35 x Rp1 1/2 42 x Rp1 1/4 42 x Rp1 1/2 54 x Rp1 1/2 54 x Rp2

Article No. 619041.5 619042.6 619043.7 619044.8 619046.1 619047.0 619045.9 619330.8 619050.3 619048.1 619049.2 619051.4 619053.6 619052.5 619055.8 619054.7 619056.9 619057.1

L 37,3 39,2 37,0 38,0 36,5 39,5 43,6 38,0 40,0 44,6 47,0 46,0 50,0 50,0 52,0 54,0 58,0 63,0

Z 7,3 8,2 7,0 7,0 5,5 7,5 9,6 4,5 6,0 8,6 9,0 7,0 9,0 10,0 3,0 10,0 9,0 10,0

Providing suitable solutions

145

Stainless steel

146

6.1

R 2728 Angle adapter 90°

R 2709 Angle adapter 90°

(press x male thread)

(press x female thread)

Dimension 15 x R1/2 18 x R1/2 22 x R3/4 28 x R1 35 x R1 1/4 42 x R1 1/2 54 x R2

Article No. 619087.7 619088.8 619089.9 619090.1 619091.0 619092.1 619093.2

L2 43,0 43,5 48,5 53,0 60,0 69,0 82,0

Z 23,0 23,5 27,5 30,0 34,0 39,0 47,0

L1 30,5 31,5 38,5 46,0 52,0 58,0 68,0

Dimension 15 x Rp1/2 18 x Rp1/2 22 x Rp1/2 22 x Rp3/4 28 x Rp1/2 28 x Rp3/4 28 x Rp1 35 x Rp1/2 35 x Rp3/4 35 x Rp1 35 x Rp1 1/4

Article No. 619082.2 619083.3 619845.6 619084.4 619846.7 619847.8 619085.5 619848.9 619849.1 619850.0 619086.6

L2 43,5 43,5 45,0 48,5 47,5 50,5 54,5 56,0 57,5 58,0 62,0

Z2 23,5 23,5 24,0 27,5 24,5 27,5 31,5 30,0 31,5 32,0 36,0

L1 28,2 28,2 31,0 33,0 35,0 35,0 37,0 35,0 37,0 40,5 42,2

Z1 13,2 13,2 16,0 17,0 16,0 18,5 17,5 20,0 21,0 21,0 20,5

Providing suitable solutions

147

Stainless steel

148

R 2710 Angle adapter 90°

R 2735 Straight union

(male x female thread)

(press x male thread)

Dimension 15 x Rp1/2

Article No. 619227.4

L2 44,0

Z2 24,0

L1 28,2

R 2704 Coupling with nut (press x female thread)

Dimension 15 x G3/4 18 x G3/4 22 x G1 28 x G1 1/4 35 x G1 1/2 42 x G1 3/4 54 x G2 3/8

Article No. 619173.5 619174.6 619175.7 619176.8 619177.9 619178.1 619179.0

L 31,0 31,0 32,0 33,0 36,0 43,0 50,0

Z1 13,2

Dimension 15 x R1/2 15 x R3/4 18 x R1/2 18 x R3/4 22 x R1/2 22 x R3/4 22 x R1 28 x R1 35 x R1 1/4 42 x R1 1/2 54 x R2

Article No. 619212.0 619213.1 619214.2 619215.3 619216.4 619217.5 619218.6 619219.7 619220.8 619221.9 619229.6

6.1

L 61,8 64,7 61,8 64,7 63,0 68,5 71,8 72,8 78,2 85,4 100,0

Z 41,8 44,7 41,8 44,7 42,0 47,5 50,8 49,8 52,2 55,4 65,0

Z 11,0 11,0 11,0 10,0 10,0 13,0 15,0

Providing suitable solutions

149

Stainless steel

150

6.1

R 2738 Straight union

R 2716 Wallplate 90°

(press x female thread)

(press x female thread)

Dimension 15 x Rp1/2 15 x Rp3/4 18 x Rp1/2 18 x Rp3/4 22 x Rp3/4 22 x Rp1 28 x Rp1 35 x Rp1 1/4 42 x Rp1 1/2 54 x Rp2

Article No. 619202.1 619203.2 619204.3 619205.4 619206.5 619207.6 619208.7 619209.8 619210.9 619211.1

L 57,0 60,0 57,0 60,0 63,0 65,8 65,0 73,0 82,0 91,0

Z 22,0 23,5 22,0 23,5 25,5 25,3 22,5 25,3 30,0 30,0

Dimension 15 x Rp1/2 18 x Rp1/2 22 x Rp3/4

Article No. 619180.1 619181.2 619182.3

D 5,0 5,0 5,5

L1 45,0 44,5 48,5

Z1 25,0 24,5 27,5

A 34 34 40

Z2 13,2 13,2 16,7

C 41,2 44,2 52,0

L1 45,0 44,5 48,5

Z1 25,0 24,5 27,5

A 40 40 40

Z2 13,2 13,2 16,7

C 63,2 63,2 64,0

R 2737 Wallplate 90° long (press x female thread)

Dimension 15 x Rp1/2 18 x Rp1/2 22 x Rp3/4

Article No. 619199.9 619200.1 619201.0

D 5,0 5,0 5,5

Providing suitable solutions

151

Stainless steel

152

R 2719 Wallplate 90°

R 2729 Stop end

(2 x press x female thread)

(1 x press)

Dimension Article No. 15 x Rp1/2 x 15 619228.5

D 5,0

L1 Z1 A Z2 C C2 L2 35,0 15,0 34,0 14,0 28,2 41,2 31,0

R 2726 Flanged connector PN 10/16 (1 x press)

Dim. 15 18 22 28 35 42 54 76,1 88,9 108

Article No. 619075.6 619076.7 619077.8 619078.9 619079.1 619080.0 619081.1 620412.1 620413.2 620414.3

Z 34,0 40,0 42,5 48,0 53,0 61,0 77,0 71,0 84,0 90,0

D 95,0 95,0 105,0 115,0 140,0 150,0 165,0 185,0 200,0 220,0

H 54,0 60,0 63,5 71,0 79,0 91,0 112,0 126,0 147,0 167,0

K 65,0 65,0 75,0 85,0 100,0 110,0 125,0 145,0 160,0 180,0

B 11,0 11,0 12,0 14,0 15,0 16,0 18,0 18,0 20,0 20,0

D2 14,0 14,0 14,0 14,0 18,0 18,0 18,0 18,0 18,0 18,0

Dimension 15 18 22 28 35 42 54 76,1 88,9 108

Article No. 619101.1 619102.0 619103.1 619104.2 619105.3 619106.4 619107.5 620418.7 620419.8 620420.9

6.1

L

Z 22,9 22,9 24,1 26,1 29,1 36,6 41,6 95,0 107,0 127,0

2,9 2,9 3,1 3,1 3,1 6,6 6,6 40,0 44,0 50,0

Holes 4 4 4 4 4 4 4 4 8 8 Providing suitable solutions

153

Stainless steel

154

6.1

R 2736 Coupling

R 2748 Transition for grooved couplings

(press x flat seal)

(press x groove)

Dimension 15 x 1 1/8 15 x 1 1/2 18 x 1 1/4 18 x 1 1/2 22 x 1 1/4 22 x 1 1/2 28 x 1 1/2 35 x 2 42 x 2 1/4 54 x 2 3/4

Article No. 619189.1 619190.0 619191.1 619192.2 619193.3 619194.4 619195.5 619196.6 619197.7 619198.8

L 30,0 30,0 29,0 29,0 28,0 28,0 30,5 33,0 37,0 44,0

Z 10,0 10,0 9,0 9,0 7,0 7,0 7,5 7,0 7,0 9,0

B 34,0 44,4 38,8 44,4 38,8 44,4 44,4 56,0 62,0 77,6

Dimensions 28 x 33,7 35 x 42,4 42 x 48,3 54 x 60,3 76,1 x 76,1 88,9 x 88,9 108 x 114

Article no. 619855.5 619856.6 619857.7 619858.8 619331.9 619332.1 619333.0

L 72,5 81,0 86,0 96,5 90,0 100,0 110,0

D

Z

33,7 42,4 48,3 60,3 76,1 88,9 114,4

26,0 26,0 26,0 26,0 36,0 36,0 36,0

Providing suitable solutions

155

Stainless steel

156

6.1

R 2749 Slip coupling

R 2756 Axial compensator

(press x female thread)

(male x male)

Dimensions 22 x Rp1/2 22 x Rp3/4 28 x Rp1/2 28 x Rp3/4

Article no. 619851.1 619852.2 619853.3 619854.4

A 92,0 97,0 94,0 93,0

B 25,0 25,0 30,0 30,0

C 15,0 16,0 15,0 16,0

∆L 40,0 40,0 40,0 40,0

D 24,0 27,0 36,5 44,0 50,0 60,0 54,0

s

L

Dimensions 76,1 88,9 108

Article no. 619837.9 619838.1 619839.0

L0 275,0 289,0 345,0

D 96,0 115,0 140,0

s 2,0 2,0 2,0

L 115,0 109,0 125,0

R 2747 Axial compensator (press x press)

Dimensions 15 18 22 28 35 42 54

Article no. 619830.2 619831.3 619832.4 619833.5 619834.6 619835.7 619836.8

L0 110,0 106,0 120,0 130,0 140,0 153,0 180,0

1,0 1,0 1,2 1,2 1,5 1,5 1,5

60,0 57,0 70,0 76,0 78,0 81,0 100,0 Providing suitable solutions

157

Stainless steel

6.1

C 1451 O-ring standard leak before pressed (LBP)

R 2764 O-ring special leak before pressed (LBP)

(black, EPDM) for carbon steel and stainless steel

(green, Viton® FPM) for carbon steel and stainless steel

Dimension 15 18 22 28 35 42 54

Article No. 622221.6 622222.7 622223.8 622224.9 622225.1 622226.0 622227.1

158

Dimension 15 18 22 28 35 42 54

Article No. 611940.1 611941.0 611942.1 611943.2 611944.3 611945.4 611946.5

159

R 2761 O-ring special R 2760 O-ring standard

(green, Viton® FPM) for carbon steel and stainless steel

(black, EPDM) for carbon steel and stainless steel Dimension 76,1 88,9 108

Article No. 620801.5 620802.6 620803.7

Dimension 76,1 88,9 108

Article No. 611937.7 611938.8 611939.9

R 2763 O-ring special leak before pressed (LBP) (grey, Viton® FPM) for stainless steel Dimension 15 18 22 28 35 42 54

Article No. 611978.4 611979.5 611980.6 611981.7 611982.8 611983.9 611984.1

Providing suitable solutions

Stainless steel

6.1 6.2

VSH 6 Product range 160

161

6.2 XPress stainless steel GAS

Providing suitable solutions

Stainless steel GAS

R 2750  Stainless steel tube 1.4401 (6m length)

Dimension 15 x 1,0 18 x 1,0 22 x 1,2 28 x 1,2 35 x 1,5 42 x 1,5 54 x 1,5 76,1 x 2,0 88,9 x 2,0 108 x 2,0

DN 12 15 20 25 32 40 50 65 80 100

R 2703G Slip coupling Article No. 611791.4 611792.5 611793.6 611794.7 611795.8 611796.9 611797.1 611798.0 611799.1 611800.2

R 2701G Straight coupling (2 x press)

Article No. 621000.6 621001.7 621002.8 621003.9 621004.1 621005.0 621006.1

(2 x press)

Dimension 15 x 15 18 x 18 22 x 22 28 x 28 35 x 35 42 x 42 54 x 54

162

Dimension 15 x 15 18 x 18 22 x 22 28 x 28 35 x 35 42 x 42 54 x 54

L 52,0 53,0 56,0 62,0 71,0 78,0 90,0

6.2

Article No. 621010.5 621011.6 621012.7 621013.8 621014.9 621015.1 621016.0

L 74,0 78,0 82,0 92,0 99,0 114,0 138,0

es 25,0 25,0 25,0 30,0 30,0 40,0 40,0

Z 12,0 13,0 14,0 16,0 19,0 18,0 20,0

Providing suitable solutions

163

Stainless steel GAS

164

R 2708G Elbow 90°

R 2711G Elbow 90°

(2 x press)

(press x male)

Dimension 15 x 15 18 x 18 22 x 22 28 x 28 35 x 35 42 x 42 54 x 54

Article No. 621017.1 621018.2 621019.3 621020.4 621021.5 621022.6 621023.7

L 47,0 54,0 61,0 72,0 86,0 112,0 138,0

Z 27,0 34,0 40,0 49,0 60,0 82,0 103,0

Dimension 15 x Ø15 18 x Ø18 22 x Ø22 28 x Ø28 35 x Ø35 42 x Ø42 54 x Ø54

Article No. 621027.0 621028.1 621029.2 621030.3 621031.4 621032.5 621033.6

6.2

L 47,0 54,0 61,0 72,0 86,0 112,0 138,0

Z 27,0 34,0 40,0 49,0 60,0 82,0 103,0

H 64,0 72,0 76,0 91,0 92,0 119,0 145,0

Providing suitable solutions

165

Stainless steel GAS

166

R 2713G Elbow 45°

R 2712G Elbow 45°

(2 x press)

(press x male)

Dimension 15 x 15 18 x 18 22 x 22 28 x 28 35 x 35 42 x 42 54 x 54

Article No. 621037.1 621038.0 621039.1 621040.2 621041.3 621042.4 621043.5

L

Z 36,0 37,0 43,0 50,0 58,0 72,0 85,0

16,0 17,0 22,0 27,0 32,0 42,0 50,0

Dimension 15 x Ø15 18 x Ø18 22 x Ø22 28 x Ø28 35 x Ø35 42 x Ø42 54 x Ø54

Article No. 621047.9 621048.1 621049.0 621050.1 621051.2 621052.3 621053.4

6.2

L 36,0 37,0 43,0 50,0 54,0 68,0 81,0

Z 16,0 17,0 22,0 27,0 28,0 38,0 46,0

H 46,0 48,0 51,0 57,0 68,0 82,0 96,0

Providing suitable solutions

167

Stainless steel GAS

168

R 2714G Tee equal

R 2715G Tee reduced

(3 x press)

(3 x press)

Dimension 15 x 15 x 15 18 x 18 x 18 22 x 22 x 22 28 x 28 x 28 35 x 35 x 35 42 x 42 x 42 54 x 54 x 54

Article No. L1 621078.7 37,0 621079.8 39,0 621080.9 41,5 621081.1 46,0 621082.0 50,5 621083.1 59,0 621084.2 71,0

Z1 17,0 19,0 20,5 23,0 24,5 29,0 36,0

L2 34,0 39,0 40,0 47,0 54,0 60,0 71,0

Z2 14,0 19,0 19,0 24,0 28,0 30,0 36,0

Dimension 18 x 15 x 18 22 x 15 x 22 22 x 18 x 22 28 x 15 x 28 28 x 18 x 28 28 x 22 x 28 35 x 15 x 35 35 x 18 x 35 35 x 22 x 35 35 x 28 x 35 42 x 22 x 42 42 x 28 x 42 42 x 35 x 42 54 x 22 x 54 54 x 28 x 54 54 x 35 x 54 54 x 42 x 54

Article No. L1 621088.6 39,0 621089.7 41,0 621090.8 41,5 621091.9 46,0 621092.1 46,0 621093.0 46,0 621094.1 50,0 621095.2 50,5 621096.3 50,0 621097.4 51,0 621098.5 59,0 621099.6 59,0 621100.7 59,0 621101.8 71,0 621102.9 71,0 621103.1 71,0 621104.0 71,0

6.2

Z1 19,0 20,0 20,5 23,0 23,0 23,0 24,0 24,5 24,0 25,0 29,0 29,0 29,0 36,0 36,0 36,0 36,0

L2 35,0 36,0 38,0 42,0 42,0 45,0 43,0 44,0 47,0 49,0 50,0 53,0 57,0 56,0 59,0 64,0 68,0

Z2 15,0 16,0 18,0 22,0 22,0 24,0 23,0 24,0 26,0 26,0 29,0 30,0 31,0 35,0 36,0 38,0 38,0

Providing suitable solutions

169

Stainless steel GAS

170

R 2718G Tee threaded

R 2707G Reducer

(press x female thread x press)

(male x press)

Dimension 15 x Rp1/2 x 15 18 x Rp1/2 x 18 18 x Rp3/4 x 18 22 x Rp1/2 x 22 22 x Rp3/4 x 22 28 x Rp1/2 x 28 28 x Rp3/4 x 28 35 x Rp1/2 x 35 35 x Rp3/4 x 35 42 x Rp1/2 x 42 54 x Rp3/4 x 54 54 x Rp1/2 x 54 54 x Rp2 x 54

Article No. L1 621105.1 37,0 621106.2 39,0 621107.3 39,0 621108.4 41,0 621109.5 41,5 621110.6 46,0 621111.7 46,0 621112.8 50,0 621113.9 50,0 621114.1 59,0 621116.1 71,0 621115.0 69,0 621117.2 71,5

Z1 17,0 19,0 19,0 20,0 20,5 23,0 23,0 24,0 24,0 29,0 36,0 34,0 36,5

L2 37,0 38,0 42,7 41,0 41,0 44,0 45,0 47,0 48,0 46,0 58,0 54,0 70,0

Z2 22,0 23,0 26,4 26,0 24,7 29,0 28,7 32,0 31,7 31,0 41,7 39,0 44,3

Dimension Ø18 x 15 Ø22 x 15 Ø22 x 18 Ø28 x 15 Ø28 x 18 Ø28 x 22 Ø35 x 22 Ø35 x 28 Ø42 x 28 Ø42 x 35 Ø54 x 28 Ø54 x 35 Ø54 x 42

Article No. 621059.1 621060.0 621061.1 621062.2 621063.3 621064.4 621065.5 621066.6 621067.7 621068.8 621069.9 621070.1 621071.0

6.2

L 57,0 60,0 57,0 73,0 77,0 68,0 83,0 74,0 100,0 89,0 100,0 127,0 102,0

Z 37,0 40,0 37,0 53,0 57,0 47,0 62,0 51,0 77,0 63,0 77,0 101,0 72,0

d1 Ø18 Ø22 Ø22 Ø28 Ø28 Ø28 Ø35 Ø35 Ø42 Ø42 Ø54 Ø54 Ø54

d2 15 15 18 15 18 22 22 28 28 35 28 35 42

Providing suitable solutions

171

Stainless steel GAS

172

R 2705G Straight connector

R 2702G Straight connector

(press x male thread)

(press x female thread)

Dimension 15 x R1/2 18 x R1/2 22 x R1/2 22 x R1 22 x R3/4 28 x R1 35 x R1 35 x R1 1/4 35 x R1 1/2 42 x R1 1/2 54 x R2

Article No. 621123.8 621124.9 621125.1 621127.1 621126.0 621128.2 621130.4 621129.3 621131.5 621132.6 621133.7

L

Z 52,0 52,0 67,0 72,0 57,0 62,0 83,0 69,0 84,0 74,0 86,0

32,0 32,0 46,0 51,0 36,0 39,0 57,0 43,0 58,0 44,0 51,0

Dimension 15 x Rp1/2 18 x Rp1/2 22 x Rp1/2 22 x Rp3/4 22 x Rp1 28 x Rp1 35 x Rp1 35 x Rp1 1/4 42 x Rp1 1/2 54 x Rp2

Article No. 621134.8 621135.9 621136.1 621137.0 621138.1 621139.2 621141.4 621140.3 621142.5 621144.7

6.2

L 53,0 51,0 52,0 62,0 84,0 67,0 88,0 71,0 73,0 85,0

Z 18,0 16,0 16,0 24,7 44,0 25,0 43,0 23,6 21,6 24,3

Providing suitable solutions

173

Stainless steel GAS

174

6.2

R 2728G Angle adapter 90°

R 2741G Valve connector

(press x male thread)

(press x female thread)

Dimension 15 x R1/2 18 x R1/2 22 x R3/4 28 x R1 35 x R1 1/4

Article No. 621145.8 621146.9 621147.1 621148.0 621149.1

L2 56,0 56,0 59,0 65,0 71,0

Z 36,0 36,0 38,0 42,0 45,0

L1 37,0 37,0 39,0 44,0 49,0

Dimension 15 x G7/8 22 x G1 1/8 28 x G1 3/8

Article No. 621180.1 621158.1 621159.0

R 2709G Angle adapter 90°

R 2716G Wallplate 90°

(press x female thread)

(press x female thread)

Dimension Article No. 15 x Rp1/2 621150.2 18 x Rp1/2 621151.3 22 x Rp3/4 621152.4 28 x Rp1 621153.5 35 x Rp1 1/4 621154.6

L2 56,0 56,0 59,0 65,0 71,0

Z2 36,0 36,0 38,0 42,0 45,0

L1 37,0 39,0 46,0 54,0 63,0

Z1 22,0 24,0 29,7 35,0 41,6

Dimension 15 x Rp1/2 18 x Rp1/2 22 x Rp3/4

Article No. 621155.7 621156.8 621157.9

D 5,0 5,0 6,0

L 33,0 42,0 45,0

L1 49,0 49,0 53,0

Z1 29,0 29,0 32,0

Z

175

9,0 16,0 17,0

A 34,0 34,0 40,0

Z2 15,0 15,0 17,7

C 43,0 43,0 51,0

Providing suitable solutions

Stainless steel GAS

176

6.2

R 2729G Stop end

R 2726G Flanged connector PN10/16

(1 x press)

(1 x press)

Dimension 15 18 22 28 35 42 54

Article No. 621205.2 621206.3 621207.4 621208.5 621209.6 621210.7 621211.8

L 37,0 39,0 41,0 46,0 51,0 60,0 71,0

Z 17,0 19,0 20,0 23,0 25,0 30,0 36,0

Dim. 22 28 35 42 54

Article No. Z 621160.1 42,5 621161.2 48,0 621162.3 53,0 621163.4 61,0 621164.5 77,0

D 105,0 115,0 140,0 150,0 165,0

H 63,5 71,0 79,0 91,0 112,0

K 75,0 85,0 100,0 110,0 125,0

B 12,0 14,0 15,0 16,0 18,0

D2 14,0 14,0 18,0 18,0 18,0

Holes 4 4 4 4 4

R 2742G Flange seal for stainless steel GAS (yellow, NBR) for stainless steel GAS Dimension 22 28 35 42 54

Article No. 621168.9 621169.1 621170.0 621171.1 621172.2

Providing suitable solutions

177

Stainless steel GAS

6.2 6.3

R 2755G O-ring Standard (yellow, HNBR) for stainless steel GAS Dimension 15 18 22 28 35 42 54

Article No. 621191.1 621192.0 621193.1 621194.2 621195.3 621196.4 621197.5

VSH 6 Product range

178

179

6.3 XPress carbon steel

Al rights reserved

Providing suitable solutions

Carbon steel

180

6.3

C 1459  Galvanized steel tube

C 1460 PP-Galvanized steel tube

(6m length)

(6m length) polypropylene coated

Dimension 12 x 1,2 15 x 1,2 18 x 1,2 22 x 1,5 28 x 1,5 35 x 1,5 42 x 1,5 54 x 1,5 76,1 x 2,0 88,9 x 2,0 108 x 2,0

DN 10 12 15 20 25 32 40 50 65 80 100

Article No. 620459.4 620460.5 620461.6 620462.7 620463.8 620464.9 620465.1 620466.0 620480.3 620481.4 620482.5

Dimension 15 x 1,2 18 x 1,2 22 x 1,5 28 x 1,5 35 x 1,5 42 x 1,5 54 x 1,5

DN 12 15 20 25 32 40 50

Article No. 620468.2 620469.3 620470.4 620471.5 620472.6 620473.7 620474.8

Providing suitable solutions

181

Carbon steel

182

6.3

C 1461  VSH Press Sprinkler Galvanized tube

C 1401 Straight coupling

(6m length)

(2 x press)

Dimensions 22 x 1,5 28 x 1,5 35 x 1,5 42 x 1,5 54 x 1,5 76,1 x 2,0 88,9 x 2,0 108 x 2,0

DN 20 25 32 40 50 65 80 100

Article no. 624111.4 624112.5 624113.6 624114.7 624115.8 624137.8 624138.9 624139.1

Dimension 12 x 12 15 x 15 18 x 18 22 x 22 28 x 28 35 x 35 42 x 42 54 x 54 76,1 x 76,1 88,9 x 88,9 108 x 108

Article No. 620135.1 620136.0 620137.1 620138.2 620139.3 620140.4 620141.5 620142.6 620620.0 620621.1 620622.2

L 47,0 53,0 53,0 55,0 59,0 65,0 76,0 86,0 142,0 160,0 199,0

Z 13,0 13,0 13,0 13,0 13,0 13,0 16,0 16,0 28,0 34,0 41,0

Providing suitable solutions

183

Carbon steel

184

6.3

C 1403 Slip coupling

C 1432 Combination tube press

(2 x press)

(ungalvanized, 2 x male)

Dimension 12 x 12 15 x 15 18 x 18 22 x 22 28 x 28 35 x 35 42 x 42 54 x 54 76,1 x 76,1 88,9 x 88,9 108 x 108

Article No. 620143.7 620144.8 620145.9 620146.1 620147.0 620148.1 620149.2 620150.3 620623.3 620624.4 620625.5

L 67,0 80,0 80,0 84,0 91,0 102,0 120,0 140,0 230,0 262,0 304,0

es 25,0 25,0 25,0 25,0 30,0 30,0 40,0 40,0 60,0 70,0 80,0

Dimension Ø17 x Ø15 Ø20 x Ø18 Ø24 x Ø22 Ø31 x Ø28 Ø38 x Ø35 Ø44,5 x Ø42 Ø57 x Ø54 Ø80,5 x Ø76,1 Ø94,9 x Ø88,9 Ø114 x Ø108

Article No. 620781.7 620782.8 620716.8 620717.9 620151.4 620152.5 620153.6 620653.0 620654.1 620655.2

L 120,0 120,0 120,0 120,0 120,0 120,0 120,0 230,0 230,0 230,0

After welding a protective coating is required against corrosion!

Providing suitable solutions

185

Carbon steel

186

C 1408 Elbow 90°

C 1411 Elbow 90°

(2 x press)

(press x male)

Dimension 12 x 12 15 x 15 18 x 18 22 x 22 28 x 28 35 x 35 42 x 42 54 x 54 76,1 x 76,1 88,9 x 88,9 108 x 108

Article No. 620154.7 620155.8 620156.9 620157.1 620158.0 620159.1 620160.2 620161.3 620800.4 620804.8 620805.9

L 35,0 41,0 45,0 51,0 60,0 71,0 86,0 105,0 150,0 174,0 215,0

Z 18,0 21,0 25,0 30,0 37,0 45,0 56,0 70,0 95,0 111,0 139,0

Dimension 12 x Ø12 15 x Ø15 18 x Ø18 22 x Ø22 28 x Ø28 35 x Ø35 42 x Ø42 54 x Ø54 76,1 x Ø76,1 88,9 x Ø88,9 108 x Ø108

Article No. 620162.4 620163.5 620164.6 620165.7 620166.8 620167.9 620168.1 620169.0 620806.1 620807.0 620808.1

6.3

L

Z

h

35,0 41,0 45,0 51,0 60,0 71,0 86,0 105,0 149,0 172,0 198,0

18,0 21,0 25,0 30,0 37,0 45,0 56,0 70,0 94,0 109,0 122,0

42,4 48,6 51,4 58,1 65,5 75,9 92,5 110,6 166,0 190,0 230,0

Providing suitable solutions

187

Carbon steel

188

C 1413 Elbow 45°

C 1412 Elbow 45°

(2 x press)

(press x male)

Dimension 15 x 15 18 x 18 22 x 22 28 x 28 35 x 35 42 x 42 54 x 54 76,1 x 76,1 88,9 x 88,9 108 x 108

Article No. 620170.1 620171.2 620172.3 620173.4 620174.5 620175.6 620176.7 620809.2 620810.3 620811.4

L 30,5 32,1 35,2 40,1 46,4 56,1 66,9 98,0 113,0 138,0

Z 10,5 12,1 14,2 17,1 20,4 26,1 31,9 43,0 50,0 62,0

Dimension 15 x Ø15 18 x Ø18 22 x Ø22 28 x Ø28 35 x Ø35 42 x Ø42 54 x Ø54 76,1 x Ø76,1 88,9 x Ø88,9 108 x Ø108

Article No. 620177.8 620178.9 620179.1 620180.0 620181.1 620182.2 620183.3 620812.5 620813.6 620814.7

6.3

L

Z 30,5 32,1 35,2 40,1 46,4 56,1 66,9 96,0 110,0 137,0

h 10,5 12,1 14,2 17,1 20,4 26,1 31,9 41,0 47,0 61,0

38,1 38,5 42,3 45,6 51,3 62,6 72,5 119,0 130,0 160,0

Providing suitable solutions

189

Carbon steel

190

C 1425 Bend 90°

C 1417 Crossover

(2 x male)

(2 x male)

Dimension Ø12 x Ø12 Ø15 x Ø15 Ø18 x Ø18 Ø22 x Ø22 Ø28 x Ø28 Ø35 x Ø35 Ø42 x Ø42 Ø54 x Ø54

Article No. 620184.4 620185.5 620186.6 620187.7 620188.8 620189.9 620190.1 620191.0

h1 70,0 70,0 70,0 72,0 82,0 120,0 150,0 200,0

h1min 58,0 58,0 63,0 70,0 80,0 100,0 120,0 145,0

h2 120,0 120,0 120,0 120,0 120,0 200,0 250,0 300,0

h2min 58,0 58,0 63,0 70,0 80,0 100,0 120,0 145,0

Dimension Ø12 x Ø12 Ø15 x Ø15 Ø18 x Ø18 Ø22 x Ø22 Ø28 x Ø28

Article No. 620192.1 620193.2 620194.3 620195.4 620196.5

6.3

L 54,0 54,0 59,5 64,5 75,0

A 155,0 155,0 167,0 177,0 215,0

B 31,0 31,0 34,0 37,0 43,0

191

C 1416 Tee reduced (3 x press)

Dimension 22 x 15 x 15 22 x 22 x 15

Article No. 620673.9 620674.1

L1 39,5 39,5

Z1 18,5 18,5

L2 47,5 48,5

Z2 27,5 27,5

L3 46,5 48,5

Z3 26,5 28,5

Providing suitable solutions

Carbon steel

192

C 1414 Tee equal

C 1415 Tee reduced

(3 x press)

(3 x press)

Dimension 12 x 12 x 12 15 x 15 x 15 18 x 18 x 18 22 x 22 x 22 28 x 28 x 28 35 x 35 x 35 42 x 42 x 42 54 x 54 x 54 76,1 x 76,1 x 76,1 88,9 x 88,9 x 88,9 108 x 108 x 108

Article No. 620248.2 620249.3 620250.4 620251.5 620252.6 620253.7 620254.8 620255.9 620644.2 620645.3 620646.4

L1 30,5 35,0 36,5 39,5 44,5 51,0 60,0 71,0 116,0 131,0 152,0

Z1 13,5 15,0 16,5 18,5 21,5 25,0 30,0 36,0 61,0 68,0 78,0

L2 39,5 44,0 45,5 48,5 53,5 60,0 66,5 77,5 121,0 126,0 152,0

Z2 22,5 24,0 25,5 27,5 30,5 34,0 36,5 42,5 61,0 63,0 74,0

Dimension 12 x 15 x 12 15 x 12 x 15 15 x 18 x 15 15 x 22 x 15 18 x 12 x 18 18 x 15 x 18 18 x 22 x 18 22 x 12 x 22 22 x 15 x 22 22 x 18 x 22 22 x 28 x 22 28 x 15 x 28 28 x 18 x 28 28 x 22 x 28 35 x 15 x 35 35 x 18 x 35 35 x 22 x 35 35 x 28 x 35 42 x 22 x 42 42 x 28 x 42 42 x 35 x 42 54 x 22 x 54 54 x 28 x 54 54 x 35 x 54 54 x 42 x 54 76,1 x 22 x 76,1 76,1 x 28 x 76,1

Article No. L1 620276.8 30,5 620256.1 35,0 620277.9 35,0 620278.1 35,0 620257.0 36,5 620258.1 36,5 620279.0 36,5 620259.2 39,5 620260.3 39,5 620261.4 39,5 620280.1 39,5 620262.5 44,5 620263.6 44,5 620264.7 44,5 620265.8 51,0 620266.9 51,0 620267.1 51,0 620268.0 51,0 620269.1 60,0 620270.2 60,0 620271.3 60,0 620272.4 71,0 620273.5 71,0 620274.6 71,0 620275.7 71,0 620704.7 116,0 620705.8 116,0

6.3

Z1 13,5 15,0 15,0 15,0 16,5 16,5 16,5 18,5 18,5 18,5 18,5 21,5 21,5 21,5 25,0 25,0 25,0 25,0 30,0 30,0 30,0 36,0 36,0 36,0 36,0 61,0 61,0

L2 42,5 41,0 44,0 47,5 42,5 45,5 47,0 44,5 47,5 47,5 52,0 50,5 50,5 51,5 54,0 54,0 55,0 57,0 57,5 59,5 62,5 63,5 65,5 68,5 72,5 68,0 71,0

Z2 22,5 24,0 24,0 26,5 25,5 25,5 26,0 27,5 27,5 27,5 29,0 30,5 30,5 30,5 34,0 34,0 34,0 34,0 36,5 36,5 36,5 42,5 42,5 42,5 42,5 45,0 47,0

Providing suitable solutions

193

Carbon steel

194

6.3

C 1415 Tee reduced (continued)

C 1418 Tee threaded

(3 x press)

(press x female thread x press)

Dimension 76,1 x 35 x 76,1 76,1 x 42 x 76,1 76,1 x 54 x 76,1 88,9 x 22 x 88,9 88,9 x 28 x 88,9 88,9 x 35 x 88,9 88,9 x 42 x 88,9 88,9 x 54 x 88,9 88,9 x 76,1 x 88,9 108 x 22 x 108 108 x 28 x 108 108 x 35 x 108 108 x 42 x 108 108 x 54 x 108 108 x 76,1 x 108 108 x 88,9 x 108

Article No. 620706.9 620707.1 620647.5 620965.4 620966.5 620967.6 620968.7 620969.8 620648.6 620971.1 620972.0 620973.1 620974.2 620975.3 620976.4 620649.7

L1 116,0 116,0 116,0 131,0 131,0 131,0 131,0 131,0 131,0 156,0 156,0 156,0 156,0 156,0 156,0 156,0

Z1 61,0 61,0 61,0 68,0 68,0 68,0 68,0 68,0 68,0 78,0 78,0 78,0 78,0 78,0 78,0 78,0

L2 75,0 79,0 80,0 76,0 75,5 83,0 85,0 92,5 128,0 85,0 87,5 93,5 96,0 102,0 125,0 135,0

Z2 48,0 47,0 43,0 53,0 51,5 56,5 53,0 55,5 73,0 62,0 63,5 66,0 64,0 65,0 70,0 72,0

Dimension 15 x Rp1/2 x 15 18 x Rp1/2 x 18 18 x Rp3/4 x 18 22 x Rp1/2 x 22 22 x Rp3/4 x 22 28 x Rp1/2 x 28 28 x Rp3/4 x 28 28 x Rp1 x 28 35 x Rp1/2 x 35 35 x Rp3/4 x 35 35 x Rp1 x 35 42 x Rp1/2 x 42 42 x Rp3/4 x 42 42 x Rp1 x 42 54 x Rp1/2 x 54 54 x Rp3/4 x 54 54 x Rp1 x 54 76,1 x Rp3/4 x 76,1 88,9 x Rp3/4 x 88,9 108 x Rp3/4 x 108

Article No. L1 620281.2 35,0 620282.3 36,5 620984.1 36,5 620283.4 39,5 620670.6 39,5 620284.5 44,5 620718.1 44,5 620960.1 44,5 620285.6 51,0 620710.2 51,0 620961.0 51,0 620286.7 60,0 620711.3 60,0 620962.1 60,0 620287.8 71,0 620712.4 71,0 620779.5 71,0 620650.8 116,0 620651.9 131,0 620652.1 156,0

Z1

L2 15,0 16,5 16,5 18,5 18,5 21,5 21,5 21,5 25,0 25,0 25,0 30,0 30,0 30,0 36,0 36,0 36,0 61,0 68,0 78,0

Z2 36,5 37,0 40,0 39,0 41,0 42,0 44,0 46,0 45,5 47,5 50,0 48,0 50,0 52,5 54,0 56,0 60,0 69,0 76,0 86,0

21,5 22,0 23,7 24,0 24,7 27,0 27,7 27,5 30,5 31,2 31,0 33,0 33,7 33,5 39,0 39,7 41,0 52,0 59,0 69,0

Providing suitable solutions

195

Carbon steel

196

6.3

C 1407 Reducer

C 1405 Straight connector

(male x press)

(press x male thread)

Dimension Ø15 x 12 Ø18 x 12 Ø18 x 15 Ø22 x 12 Ø22 x 15 Ø22 x 18 Ø28 x 15 Ø28 x 18 Ø28 x 22 Ø35 x 22 Ø35 x 28 Ø42 x 22 Ø42 x 28 Ø42 x 35 Ø54 x 18 Ø54 x 22 Ø54 x 28 Ø54 x 35 Ø54 x 42 Ø76,1 x 42 Ø76,1 x 54 Ø88,9 x 54 Ø88,9 x 76,1 Ø108 x 76,1 Ø108 x 88,9

Article No. 620211.9 620212.1 620213.0 620214.1 620215.2 620216.3 620217.4 620218.5 620219.6 620220.7 620221.8 620665.1 620666.2 620222.9 620667.3 620223.1 620224.0 620668.4 620225.1 620638.7 620639.8 620640.9 620641.1 620642.0 620643.1

L

Z 55,0 53,8 52,0 57,2 58,4 59,0 64,0 62,3 63,0 68,0 69,0 80,0 79,0 76,0 97,0 89,0 87,0 89,0 91,0 151,0 145,0 157,0 157,0 196,0 192,0

38,0 36,8 32,0 40,2 38,4 39,0 44,0 42,3 42,0 47,0 46,0 59,0 56,0 50,0 77,0 68,0 64,0 63,0 61,0 121,0 110,0 122,0 102,0 141,0 129,0

d1 15,0 18,0 18,0 22,0 22,0 22,0 28,0 28,0 28,0 35,0 35,0 35,0 42,0 42,0 54,0 54,0 54,0 54,0 54,0 76,1 76,1 88,9 88,9 108,0 108,0

d2 12,0 12,0 15,0 12,0 15,0 18,0 15,0 18,0 22,0 22,0 28,0 22,0 28,0 35,0 18,0 22,0 28,0 35,0 42,0 42,0 54,0 54,0 76,1 76,1 88,9

Dimension 12 x R3/8 15 x R3/8 15 x R1/2 18 x R1/2 18 x R3/4 22 x R1/2 22 x R3/4 22 x R1 28 x R3/4 28 x R1 35 x R1 1/4 42 x R1 1/2 54 x R2 76,1 x R2 1/2 88,9 x R3

Article No. 620226.2 620227.3 620228.4 620229.5 620230.6 620671.7 620231.7 620672.8 620985.2 620232.8 620233.9 620234.1 620235.0 620478.1 620479.2

L 31,0 35,0 39,0 39,0 40,0 43,0 44,0 50,0 46,0 48,0 55,0 59,0 69,0 123,0 134,0

Z 14,0 15,0 19,0 19,0 20,0 22,0 23,0 29,0 23,0 25,0 29,0 29,0 34,0 68,0 71,0

Providing suitable solutions

197

Carbon steel

198

6.3

C 1402 Straight connector

C 1433 Straight connector

(press x female thread)

(male x female thread)

Dimension 12 x Rp1/2 15 x Rp1/2 18 x Rp1/2 18 x Rp3/4 22 x Rp1/2 22 x Rp3/4 28 x Rp1/2 28 x Rp3/4 28 x Rp1 35 x Rp1 1/4

Article No. 620236.1 620237.2 620238.3 620239.4 634020.2 620240.5 620780.6 620983.0 620241.6 620669.5

L 39,0 41,0 40,0 43,0 36,5 43,0 38,0 40,5 49,0 50,0

Z 7,0 6,0 5,0 6,7 4,5 5,7 2,0 1,0 7,0 2,3

Dimension Ø12 x Rp1/2 Ø12 x Rp3/8 Ø15 x Rp1/2 Ø18 x Rp1/2 Ø18 x Rp3/4 Ø22 x Rp1/2 Ø22 x Rp3/4

Article No. 620242.7 620987.4 620243.8 620244.9 620245.1 620246.0 620247.1

A 49,0 42,0 51,0 50,0 53,0 50,0 53,0

Z 34,0 30,6 36,0 35,0 36,7 35,0 36,7

D 12,0 12,0 15,0 18,0 18,0 22,0 22,0

C 1404 Straight connector (press x eurocone)

Dimension 15 x 3/4 18 x 3/4

Article No. 620816.9 620817.1

L 38,0 38,0

Z 18,0 18,0

Providing suitable solutions

199

Carbon steel

200

6.3

C 1428 Angle adapter 90°

C 1430 Elbow 90°

(press x male thread)

(press x male thread)

Dimension 12 x R3/8 15 x R3/8 15 x R1/2 18 x R1/2 22 x R3/4

Article No. 620206.4 620207.5 620208.6 620209.7 620210.8

L2 36,5 40,0 41,0 41,5 44,5

Z 19,5 20,0 21,0 21,5 23,5

L1 22,0 22,0 28,0 28,0 32,0

C 1439 Reducer (2 x press)

Dimension 22 x 15 28 x 22

Article No. 620112.9 620113.1

L 45,5 47,5

Dimension 12 x R3/8 15 x R3/8 15 x R1/2 18 x R1/2 22 x R3/4 28 x R1 35 x R1 1/4 42 x R1 1/2 54 x R2

Article No. 620197.6 620198.7 620199.8 620200.9 620201.1 620202.0 620203.1 620204.2 620205.3

B 41,5 44,5 49,5 54,0 61,5 73,5 85,5 95,5 115,5

Z 18 21 21 25 30 37 45 56 70

A 35 41 41 45 51 60 71 86 105

Z 4,5 2,5

Providing suitable solutions

201

Carbon steel

202

6.3

C 1438 Elbow 90°

C 1435 Straight union

(press x female thread)

(press x male thread)

Dimension 15 x Rp3/8 15 x Rp1/2 18 x Rp1/2 22 x Rp1/2 22 x Rp3/4 28 x Rp1/2 28 x Rp3/4 28 x Rp1 35 x Rp1/2 35 x Rp3/4 35 x Rp1

Article No. 620093.1 620094.2 620095.3 620957.7 620096.4 620702.5 620098.6 620958.8 620106.3 620107.4 620959.9

B 41,0 41,0 45,0 59,0 59,0 65,0 65,0 69,5 74,5 74,5 74,5

Z 21,0 21,0 25,0 30,0 30,0 37,0 37,0 37,0 45,0 45,0 45,0

A 40,5 46,5 50,0 51,0 51,0 60,0 60,0 60,0 71,0 71,0 71,0

Dimension 15 x R1/2 18 x R1/2 22 x R3/4 28 x R1 35 x R1 1/4 42 x R1 1/2 54 x R2

Article No. 620719.0 620703.6 620720.1 620721.2 620722.3 620723.4 620724.5

L 63,8 63,8 70,0 74,7 81,8 88,0 100,0

Z 43,8 43,8 49,0 51,7 55,8 58,0 65,0

Providing suitable solutions

203

Carbon steel

C 1444 Straight union

6.3

C 1431 Venturi nozzle

(press x female thread)

204

Dimension 15 x Rp1/2 18 x Rp1/2 22 x Rp3/4 28 x Rp1 35 x Rp1 1/4 42 x Rp1 1/2 54 x Rp2

Article No. 620890.6 620891.7 620892.8 620893.9 620894.1 620895.0 620896.1

L 58,5 58,5 63,0 65,0 75,5 82,5 92,5

Z 20,0 20,0 22,0 19,0 24,5 27,5 28,0

Dimension Ø18 Ø22 Ø28

Article No. 620292.2 620293.3 620294.4

205

Providing suitable solutions

Carbon steel

206

6.3

C 1426 Flanged connector PN16

C 1429 Stop end

(1 x press)

(1 x press)

Dimension 76,1 88,9 108

Article No. 620659.6 620660.7 620661.8

Z 79,0 78,0 88,0

D 185,0 200,0 220,0

D2 18 18 18

H 134,0 141,0 166,0

K 145,0 160,0 180,0

B 18,0 20,0 20,0

Holes 4 8 8

C 1427 Flanged connector PN6 (1 x press)

Dimension 76,1 88,9 108

Article No. 620662.9 620663.1 620664.0

Z 74,0 83,0 92,0

D 160,0 190,0 210,0

D2 14,0 18,0 18,0

H 126,0 143,0 168,0

K 130,0 150,0 170,0

B 14,0 16,0 16,0

Dimension 15 18 22 28 35 42 54 76,1 88,9 108

Article No. 620295.5 620296.6 620297.7 620298.8 620299.9 620300.1 620301.0 620691.5 620692.6 620693.7

L 25,5 26,3 28,5 32,3 34,4 43,2 51,8 70,0 87,0 98,0

Z 5,5 6,3 7,5 9,3 8,4 13,2 16,8 15,0 24,0 21,0

Holes 4 4 4

Providing suitable solutions

207

Carbon steel

208

6.3

C 1434 Pass crossing 90°

C 1436 Crossingpair double

(4 x press)

(press x male)

Dimension 15 x 15 x 15 x 15 18 x 15 x 18 x 15 22 x 15 x 22 x 15 22 x 18 x 22 x 18 28 x 15 x 28 x 15 28 x 18 x 28 x 18 28 x 22 x 28 x 22

Article No. 620288.9 620289.1 620290.0 620291.1 620713.5 620714.6 620715.7

L1 35,0 36,5 39,5 39,5 44,5 44,5 44,5

Z1 15,0 16,5 18,5 18,5 21,5 21,5 21,5

L2 35,0 35,0 35,0 36,5 35,0 36,5 39,5

Z2 15,0 15,0 15,0 16,5 15,0 16,5 18,5

h 21,0 22,5 24,5 26,0 27,5 29,0 31,0

Dimension 12 x Ø12 15 x Ø12 15 x Ø15 18 x Ø12 18 x Ø15 22 x Ø12 22 x Ø15 28 x Ø12 28 x Ø15 35 x Ø15

Article No. 620675.0 620676.1 620677.2 620678.3 620679.4 620694.8 620680.5 620681.6 620682.7 620683.8

L 100,0 120,0 120,0 120,0 120,0 120,0 120,0 120,0 120,0 120,0

Z 66,0 80,0 80,0 80,0 80,0 78,0 78,0 74,0 74,0 67,0

A 60,0 60,0 60,0 60,0 60,0 60,0 60,0 60,0 60,0 60,0

B 40,0 40,0 40,0 40,0 40,0 40,0 40,0 40,0 40,0 40,0

C 100,0 100,0 100,0 100,0 100,0 100,0 100,0 100,0 100,0 100,0

Providing suitable solutions

209

Carbon steel

210

6.3

C 1437 Crossingpair single

C 1442 Transition for grooved couplings

(press x male)

(press x groove)

Dimension 12 x Ø12 15 x Ø12 15 x Ø15 18 x Ø12 18 x Ø15 22 x Ø12 22 x Ø15 28 x Ø12 28 x Ø15

Article No. 620695.9 620696.1 620684.9 620685.1 620686.0 620687.1 620688.2 620689.3 620690.4

L1 100,0 120,0 120,0 120,0 120,0 120,0 120,0 120,0 120,0

Z1 66,0 80,0 80,0 80,0 80,0 78,0 78,0 74,0 74,0

A 60,0 60,0 60,0 60,0 60,0 60,0 60,0 60,0 60,0

B 40,0 40,0 40,0 40,0 40,0 40,0 40,0 40,0 40,0

C 100,0 100,0 100,0 100,0 100,0 100,0 100,0 100,0 100,0

Dimensions 28 x 33,7 35 x 42,4 42 x 48,3 54 x 60,3 76,1 x 76,1 88,9 x 88,9 108 x 114

Article no. 624130.1 624134.5 624135.6 624136.7 634077.4 634078.5 634079.6

L 72,5 81,0 86,0 96,5 90,0 100,0 110,0

D 33,7 42,4 48,3 60,3 76,1 88,9 114,3

Z 26,0 26,0 26,0 26,0 36,0 36,0 36,0

Providing suitable solutions

211

Carbon steel

212

6.3

C 1443 Slip coupling

C 1446 Coupling with nut

(press x female thread)

(press x female thread)

Dimensions 22 x Rp1/2 22 x Rp3/4 28 x Rp1/2 28 x Rp3/4

Article no. 624131.2 624132.3 624126.8 624127.9

A

B 92,0 97,0 94,0 93,0

C 25,0 25,0 30,0 30,0

15,0 16,0 15,0 16,0

∆L 40,0 40,0 40,0 40,0

Dimensions 15 x G3/4 18 x G3/4 22 x G1 28 x G1 1/4 35 x G1 1/2 42 x G1 3/4 54 x G2 3/8

Article no. 634052.1 634053.2 634055.4 634056.5 634057.6 634058.7 634059.8

L

Z 31,0 31,0 32,0 33,0 36,0 43,0 50,0

11,0 11,0 11,0 10,0 10,0 13,0 15,0

Providing suitable solutions

213

Carbon steel

6.3

C 1451 O-ring standard leak before pressed (LBP)

R 2764 O-ring special leak before pressed (LBP)

(black, EPDM) for carbon steel and stainless steel

(green, Viton® FPM) for carbon steel and stainless steel

Dimension 12 15 18 22 28 35 42 54

Dimension 15 18 22 28 35 42 54

Article No. 622220.5 622221.6 622222.7 622223.8 622224.9 622225.1 622226.0 622227.1

214

Article No. 611940.1 611941.0 611942.1 611943.2 611944.3 611945.4 611946.5

215

R 2761 O-ring special (green, Viton® FPM) for carbon steel and stainless steel

R 2760 O-ring standard (black, EPDM) for carbon steel and stainless steel Dimension 76,1 88,9 108

Dimension 76,1 88,9 108

Article No. 611937.7 611938.8 611939.9

Article No. 620801.5 620802.6 620803.7

Providing suitable solutions

Carbon steel

6.4 6.3

VSH 6 Product range 216

217

6.4 XPress Copper

Providing suitable solutions

Copper

218

6.4

7270 Straight coupling

7270S Slip coupling

(2 x press)

(2 x press)

Dimension 12 x 12 15 x 15 18 x 18 22 x 22 28 x 28 35 x 35 42 x 42 54 x 54 64 x 64 67 x 67 76,1 x 76,1 88,9 x 88,9 108 x 108

Article No. 480000.4 480001.5 480002.6 480003.7 480004.8 480005.9 480006.1 480007.0 480600.1 480008.1 480009.2 480010.3 480011.4

L

Z 42,0 43,0 44,0 46,0 46,0 62,0 71,0 83,0 148,0 110,0 110,0 220,0 205,0

8,0 3,0 4,0 4,0 4,0 6,0 7,0 9,0 48,0 10,0 10,0 96,0 71,0

Dimension 15 x 15 18 x 18 22 x 22 28 x 28 35 x 35 42 x 42 54 x 54 64 x 64 67 x 67 76,1 x 76,1 88,9 x 88,9 108 x 108

Article No. 480012.5 480013.6 480014.7 480015.8 480016.9 480017.1 480018.0 480665.9 480660.4 480020.2 480021.3 480022.4

L

Z 80,0 80,0 84,0 91,0 99,0 119,0 141,0 102,0 110,0 110,0 127,0 131,0

40,0 40,0 42,0 45,0 50,0 60,0 70,0 2,0 10,0 10,0 3,0 9,0

Providing suitable solutions

219

Copper

220

6.4

7002A Elbow 90°

7001A Elbow 90°

(2 x press)

(press x male)

Dimension 12 x 12 15 x 15 18 x 18 22 x 22 28 x 28 35 x 35 42 x 42 54 x 54 64 x 64 67 x 67 76,1 x 76,1 88,9 x 88,9 108 x 108

Article No. 480030.1 480031.2 480032.3 480033.4 480034.5 480035.6 480036.7 480037.8 480602.1 480038.9 480039.1 480040.0 480041.1

L 31,0 38,0 41,6 47,0 56,0 68,0 80,0 100,0 172,0 132,0 142,0 215,0 201,0

Z 14,0 17,0 22,0 26,0 34,0 42,0 50,0 65,0 122,0 87,0 92,0 112,0 135,0

r 14,4 18,0 22,0 26,4 33,6 42,0 50,0 65,0 90,0 80,0 90,0 127,0 161,0

Dimension 12 x Ø12 15 x Ø15 18 x Ø18 22 x Ø22 28 x Ø28 35 x Ø35 42 x Ø42 54 x Ø54 67 x Ø67 76,1 x Ø76,1 88,9 x Ø88,9 108 x Ø108

Article No. L 480042.2 31,4 480043.3 36,0 480044.4 41,6 480045.5 47,0 480046.6 58,0 480047.7 69,0 480048.8 81,0 480049.9 100,0 480050.1 130,0 480051.0 147,0 480052.1 215,0 480053.2 206,0

Z 14,4 16,0 21,6 27,0 34,0 44,0 52,0 66,0 78,0 98,0 153,0 141,0

L1 44,5 50,0 53,0 58,0 64,0 82,0 101,0 120,0 175,0 190,0 250,0 259,0

r 14,4 18,0 21,6 26,4 33,6 42,0 50,4 64,8 80,0 90,0 127,0 161,0

Providing suitable solutions

221

Copper

222

7041 Elbow 45°

7040 Elbow 45°

(2 x press)

(press x male)

Dimension 12 x 12 15 x 15 18 x 18 22 x 22 28 x 28 35 x 35 42 x 42 54 x 54 64 x 64 67 x 67 76,1 x 76,1 88,9 x 88,9 108 x 108

Article No. 480054.3 480055.4 480056.5 480057.6 480058.7 480059.8 480060.9 480061.1 480604.3 480062.0 480063.1 480064.2 480065.3

L 23,0 28,0 29,0 31,0 37,0 44,0 51,0 62,0 114,0 85,0 91,0 109,0 125,0

Z 6,0 8,0 9,0 12,0 16,0 18,0 21,0 27,0 64,0 35,0 45,0 47,0 59,0

Dimension 12 x Ø12 15 x Ø15 18 x Ø18 22 x Ø22 28 x Ø28 35 x Ø35 42 x Ø42 54 x Ø54 67 x Ø67 76,1 x Ø76,1 88,9 x Ø88,9 108 x Ø108

6.4

Article No. L 480066.4 23,0 480067.5 28,0 480068.8 29,0 480069.7 32,0 480070.8 37,0 480071.9 43,0 480072.1 51,0 480073.0 62,0 480674.5 85,0 480075.2 95,0 480076.3 132,0 480077.4 127,0

Z 6,0 7,5 9,0 10,9 13,9 17,4 20,9 26,8 46,0 46,0 78,0 68,0

L1 32,2 37,0 39,0 44,0 47,0 58,0 71,0 82,0 88,0 146,0 196,0 184,0

Providing suitable solutions

223

Copper

224

6.4

7086 Crossover

7087 Crossover

(press x male)

(2 x male)

Dimension 15 x Ø15 18 x Ø18 22 x Ø22

Article No. 480084.0 480085.1 480086.2

L 110,0 120,0 134,0

Z 90,0 100,0 113,0

L1 40,0 45,0 50,0

L2 44,0 49,0 55,0

L3 25,0 27,0 30,0

Dimension Ø15 x Ø15 Ø18 x Ø18 Ø22 x Ø22

Article No. 480078.5 480079.6 480080.7

7005 Bend 90°

7085 Crossover

(2 x male)

(2 x press)

Dimension Ø15 x Ø15 Ø18 x Ø18 Ø22 x Ø22 Ø28 x Ø28

Article No. h1 620184.4 70,0 620185.5 70,0 620186.6 70,0 620187.7 80,0

h1min 58,0 63,0 70,0 80,0

h2 120,0 120,0 120,0 120,0

h2min 58,0 63,0 70,0 80,0

Dimension 15 x 15 18 x 18 22 x 22

Article No. 480081.8 480082.9 480083.1

L 157,0 166,0 178,0

L 140,0 151,0 170,0

L1 56,0 60,0 65,0

Z 100,0 111,0 128,0

L1 46,0 49,0 55,0

L3 30,0 31,0 33,0

L1 26,0 27,0 28,0

Providing suitable solutions

225

Copper

226

6.4

7130 Tee equal

7130 Tee reduced

(3 x press)

(3 x press)

Dimension 12 x 12 x 12 15 x 15 x 15 18 x 18 x 18 22 x 22 x 22 28 x 28 x 28 35 x 35 x 35 42 x 42 x 42 54 x 54 x 54 64 x 64 x 64 67 x 67 x 67 76,1 x 76,1 x 76,1 88,9 x 88,9 x 88,9 108 x 108 x 108

Article No. 480159.9 480160.1 480161.0 480162.1 480163.2 480164.3 480165.4 480166.5 480608.7 480167.6 480168.7 480169.8 480170.9

L 28,0 32,0 34,0 37,0 42,0 50,0 58,0 69,0 133,0 95,0 101,0 162,0 159,0

Z 11,0 12,0 14,0 16,0 19,0 24,0 28,0 34,0 83,0 45,0 50,0 100,0 92,0

L1 28,0 32,0 34,0 37,0 42,0 50,0 58,0 69,0 134,0 107,0 114,0 162,0 159,0

Z1 11,0 12,0 14,0 16,0 19,0 24,0 28,0 34,0 84,0 58,0 64,0 100,0 92,0

Dimension 15 x 12 x 15 18 x 12 x 18 18 x 15 x 18 22 x 12 x 22 22 x 15 x 22 22 x 18 x 22 28 x 12 x 28 28 x 15 x 28 28 x 18 x 28 28 x 22 x 28 35 x 15 x 35 35 x 22 x 35 35 x 28 x 35 42 x 15 x 42 42 x 22 x 42 42 x 28 x 42 42 x 35 x 42 54 x 22 x 54 54 x 28 x 54 54 x 35 x 54 54 x 42 x 54 64 x 35 x 64 64 x 42 x 64

Article No. 480172.0 480176.4 480178.6 480567.1 480182.1 480185.2 480571.3 480188.5 480190.7 480192.9 480194.0 480195.1 480196.2 480197.3 480198.4 480199.5 480200.6 480201.7 480202.8 480203.9 480204.1 480609.8 480610.9

L 32,0 34,0 34,0 37,0 37,0 37,0 42,0 42,0 42,0 42,0 45,0 45,0 50,0 50,0 50,0 56,0 56,0 60,0 60,0 61,0 69,0 115,0 126,0

Z 12,0 14,0 14,0 16,0 16,0 16,0 19,0 19,0 19,0 19,0 19,0 19,0 24,0 20,0 20,0 26,0 26,0 25,0 25,0 36,0 34,0 65,0 76,0

L1 32,0 35,0 35,0 34,0 38,0 38,0 41,0 41,0 41,0 41,0 44,0 45,0 44,0 48,0 48,0 49,0 50,0 54,0 55,0 55,0 64,0 102,0 109,0

Z1 15,0 18,0 15,0 17,0 18,0 18,0 21,0 21,0 21,0 20,0 24,0 24,0 21,0 28,0 27,0 26,0 24,0 33,0 32,0 29,0 34,0 76,0 79,0

Providing suitable solutions

227

Copper

228

6.4

7130 Tee reduced

7130 Tee reduced

(3 x press)

(3 x press)

Dimension 67 x 28 x 67 67 x 35 x 67 67 x 42 x 67 67 x 54 x 67 76,1 x 22 x 76,1 76,1 x 28 x 76,1 76,1 x 35 x 76,1 76,1 x 42 x 76,1 76,1 x 54 x 76,1 88,9 x 54 x 88,9 88,9 x 76,1 x 88,9 108 x 54 x 108 108 x 76,1 x 108 108 x 88,9 x 108

Article No. 480619.7 480536.1 480535.0 480534.1 480537.2 480537.2 480206.1 480207.2 480208.3 480210.5 480211.6 480212.7 480213.8 480214.9

L

Z

76,0 80,0 82,0 88,0 73,0 77,0 80,0 103,0 108,0 136,0 151,0 131,0 117,0 140,0

26,0 29,0 32,0 47,0 22,0 26,0 30,0 55,0 60,0 77,0 91,0 66,0 46,0 73,0

L1 67,0 70,0 76,0 78,0 73,0 73,0 78,0 106,0 104,0 119,0 146,0 129,0 136,0 141,0

Z1 43,0 43,0 41,0 42,0 50,0 50,0 53,0 70,0 72,0 86,0 96,0 93,0 91,0 93,0

7130 Tee reduced (3 x press)

Dimension 15 x 15 x 12 18 x 18 x 15 22 x 22 x 15 22 x 22 x 18 28 x 28 x 15 28 x 28 x 22 35 x 35 x 22 35 x 35 x 28

Article No. 480173.1 480179.7 480186.3 480187.4 480540.5 480193.1 480541.6 480542.7

L 32,0 34,0 37,0 37,0 42,0 42,0 51,0 51,0

Z 12,0 14,0 16,0 16,0 19,0 19,0 25,0 25,0

L1 32,0 34,0 37,0 37,0 42,0 42,0 50,0 50,0

Z1 12,0 14,0 16,0 16,0 19,0 19,0 24,0 24,0

L2 36,0 42,0 46,0 43,0 52,0 52,0 72,0 67,0

Dimension 12 x 15 x 12 15 x 12 x 12 15 x 18 x 15 15 x 22 x 15 18 x 15 x 15 22 x 15 x 15 22 x 15 x 18 22 x 18 x 15 22 x 18 x 18 22 x 28 x 22 28 x 15 x 22 28 x 18 x 22 28 x 22 x 22 28 x 35 x 28 35 x 22 x 28 35 x 28 x 28 42 x 35 x 35 54 x 42 x 42

Article No. 480566.9 480171.1 480174.2 480175.3 480177.5 480180.8 480181.9 480183.0 480184.1 480162.1 480543.8 480189.6 480191.8 480019.1 480545.1 480546.0 480547.1 480568.0

L 36,0 32,0 35,0 38,0 34,0 37,0 37,0 37,0 37,0 52,0 42,0 42,0 42,0 68,0 51,0 51,0 56,0 69,0

Z 19,0 12,0 15,0 18,0 14,0 16,0 16,0 16,0 16,0 31,0 19,0 19,0 19,0 45,0 25,0 25,0 26,0 34,0

L1 32,0 32,0 32,0 34,0 35,0 44,0 38,0 38,0 38,0 42,0 41,0 41,0 41,0 50,0 44,0 44,0 50,0 64,0

Z1 15,0 15,0 12,0 13,0 15,0 18,0 18,0 18,0 18,0 24,0 21,0 21,0 20,0 24,0 23,0 21,0 24,0 34,0

L2 32,0 35,0 32,0 34,0 40,0 43,0 44,0 44,0 41,0 42,0 46,0 47,0 48,5 50,0 63,0 67,0 74,0 83,0

Z2 15,0 18,0 12,0 13,0 20,0 23,0 24,0 24,0 21,0 24,0 25,0 26,0 27,5 24,0 40,0 44,0 48,0 53,0

Z2 19,0 22,0 26,0 23,0 35,0 31,0 51,0 51,0 Providing suitable solutions

229

Copper

7243 Reducer

Dimension Ø88,9 x 42 Ø88,9 x 54 Ø88,9 x 76,1 Ø108 x 42 Ø108 x 54 Ø108 x 67 Ø108 x 76,1 Ø108 x 88,9

(male x press)

6.4 Article No. 480249.0 480250.1 480251.2 480252.3 480253.4 480632.9 480255.6 480256.7

L

Z 135,0 132,0 140,0 153,0 156,0 166,0 162,0 166,0

d 105,0 97,0 90,0 124,0 120,0 116,0 112,0 106,0

d1 88,9 88,9 88,9 108,0 108,0 108,0 108,0 108,0

42 54 76 42 54 67 76,1 88,9

6130G Tee threaded (press x female thread x press) 230

Dimension Ø15 x 12 Ø18 x 12 Ø18 x 15 Ø22 x 15 Ø22 x 18 Ø28 x 15 Ø28 x 18 Ø28 x 22 Ø35 x 22 Ø35 x 28 Ø42 x 22 Ø42 x 28 Ø42 x 35 Ø54 x 28 Ø54 x 35 Ø54 x 42 Ø67 x 28 Ø67 x 35 Ø67 x 42 Ø67 x 54 Ø76,1 x 35 Ø76,1 x 42 Ø76,1 x 54 Ø76,1 x 67

Article No. 480225.9 480226.1 480227.0 480228.1 480229.2 480230.3 480231.4 480232.5 480233.6 480234.7 480235.8 480236.9 480237.1 480238.0 480239.1 480240.2 480620.8 480242.4 480243.5 480244.6 480245.7 480246.8 480247.9 480248.1

L 45,0 47,0 47,0 54,0 48,0 62,0 59,0 56,0 68,0 66,0 76,0 73,0 75,0 89,0 90,0 89,0 107,0 109,0 110,0 112,0 113,0 113,0 116,0 126,0

Z

d 28,0 30,0 25,0 34,0 26,0 42,0 37,0 34,0 47,0 44,0 55,0 48,0 48,0 67,0 63,0 58,0 86,0 83,0 80,0 77,0 87,0 86,0 81,0 78,0

d1 15,0 18,0 18,0 22,0 22,0 28,0 28,0 28,0 35,0 35,0 42,0 42,0 42,0 54,0 54,0 54,0 67,0 67,0 67,0 67,0 76,1 76,1 76,1 76,1

12 12 15 15 18 15 18 22 22 28 22 28 35 28 35 42 28 35 42 54 35 42 54 67

231

Dimension 12 x Rp1/2 x 12 15 x Rp1/2 x 15 18 x Rp1/2 x 18 22 x Rp1/2 x 22 22 x Rp3/4 x 22 28 x Rp1/2 x 28 28 x Rp3/4 x 28 35 x Rp1/2 x 35 42 x Rp1/2 x 42 54 x Rp1/2 x 54 76,1 x Rp1/2 x 76,1 108 x Rp1/2 x 108

Article No. 480215.1 480216.0 480217.1 480218.2 480219.3 480220.4 480221.5 480222.6 480223.7 480224.8 480548.2 480549.3

L 28,5 41,4 42,0 42,0 45,0 44,0 41,0 50,0 57,0 69,0 65,0 82,0

Z 11,5 21,4 22,0 21,0 24,0 21,0 18,0 24,0 27,0 34,0 15,0 15,0

L1 23,0 22,5 24,0 26,0 27,3 29,0 34,0 34,0 38,0 44,0 48,0 65,0

Z1 6,5 6,5 8,0 11,0 11,0 14,0 13,5 19,0 23,0 29,0 30,0 30,0

Providing suitable solutions

Copper

232

6.4

6243G Straight connector

6270G Straight connector

(press x male thread)

(press x female thread)

Dimension 12 x R3/8 12 x R1/2 15 x R3/8 15 x R1/2 15 x R3/4 18 x R1/2 18 x R3/4 22 x R1/2 22 x R3/4 22 x R1 28 x R3/4 28 x R1 28 x R1 1/4 35 x R1 35 x R1 1/4 42 x R1 1/4 42 x R1 1/2 54 x R2 64 x R2 1/2 67 x R2 1/2 76,1 x R2 1/2 76,1 x R3 88,9 x R3 108 x R4

Article No. 480103.8 480104.9 480105.1 480106.0 480107.1 480108.2 480109.3 480110.4 480111.5 480112.6 480113.7 480114.8 480115.9 480116.1 480117.0 480118.1 480119.2 480120.3 480606.5 480121.4 480122.5 480123.6 480124.7 480125.8

L 32,0 36,0 33,0 37,0 39,0 38,0 39,0 38,0 40,0 42,0 43,0 44,0 48,0 48,0 50,0 58,0 58,0 63,0 129,0 93,0 99,0 110,0 144,0 132,0

Z 15,0 19,0 13,0 17,0 19,0 17,0 19,0 17,4 21,0 21,0 20,0 21,0 25,0 22,0 24,0 28,0 28,0 28,0 79,0 50,0 44,0 59,0 82,0 50,0

A/F 19,0 19,0 21,0 21,0 25,0 25,0 25,0 30,0 30,0 32,0 36,0 36,0 40,0 41,0 41,0 51,0 51,0 63,0 75,0 80,0 84,0 94,0 93,0 117,0

Dimension 12 x Rp3/8 12 x Rp1/2 15 x Rp3/8 15 x Rp1/2 15 x Rp3/4 18 x Rp1/2 18 x Rp3/4 22 x Rp1/2 22 x Rp3/4 22 x Rp1 28 x Rp3/4 28 x Rp1 28 x Rp1 1/4 35 x Rp3/4 35 x Rp1 35 x Rp1 1/4 42 x Rp1 1/4 42 x Rp1 1 /2 54 x Rp2 64 x Rp2 1/2

Article No. 480126.9 480127.1 480128.0 480129.1 480130.2 480131.3 480132.4 480133.5 480134.6 480135.7 480136.8 480137.9 480138.1 480569.1 480139.0 480140.1 480141.2 480142.3 480143.4 480607.6

L

Z 31,0 35,0 33,0 38,0 39,0 37,0 39,0 37,0 39,0 43,0 40,0 45,0 48,0 42,0 46,0 50,0 52,0 54,0 63,0 123,0

2,0 3,0 2,0 3,0 3,0 2,0 3,0 1,0 2,0 3,0 1,0 2,0 4,0 4,0 1,0 1,0 1,0 2,0 2,0 12,0

A/F 20,0 25,0 20,0 25,0 30,0 25,0 30,0 30,0 30,0 37,0 37,0 37,0 46,0 30,0 41,0 46,0 46,0 53,0 65,0 83,0

Providing suitable solutions

233

Copper

234

6.4

6280G Straight connector

6246G Straight connector

(male x male thread)

(male x female thread)

Dimension 15 x R1/2 18 x R1/2 18 x R3/4 22 x R1/2 22 x R3/4 28 x R1 35 x R1 1/4 42 x R1 1/2

Article No. 480325.1 480326.0 480327.1 480328.2 480329.3 480330.4 480331.5 480332.6

L 50,0 50,0 53,0 51,0 52,0 57,0 63,0 80,0

A/F 19,0 19,0 25,0 25,0 25,0 32,0 40,0 46,0

Dimension 15 x Rp1/2 18 x Rp1/2 18 x Rp3/4 22 x Rp1/2 22 x Rp3/4 28 x Rp3/4 28 x Rp1 35 x Rp1 35 x Rp1 1/4 42 x Rp1 1/2 54 x Rp2

Article No. 480311.7 480312.8 480313.9 480314.1 480315.0 480316.1 480317.2 480318.3 480319.4 480320.5 480321.6

a 47,0 47,0 49,0 46,0 49,0 50,0 54,0 56,0 60,0 76,0 86,0

A/F 32,0 32,0 33,0 31,0 32,0 34,0 35,0 37,0 38,0 55,0 60,0

Z 25,0 25,0 30,0 25,0 30,0 30,0 37,0 37,0 46,0 53,0 65,0

Providing suitable solutions

235

Copper

236

6.4

6092G Angle adapter 90°

6096G Angle adapter 90°

(press x male thread)

(press x female thread)

Dimension 12 x R3/8 12 x R1/2 15 x R3/8 15 x R1/2 18 x R1/2 18 x R3/4 22 x R3/4 28 x R1 35 x R1 1/4 42 x R1 1/2 54 x R2

Article No. 480092.8 480093.9 480094.1 480095.0 480096.1 480097.2 480098.3 480099.4 480100.5 480101.6 480102.7

L 30,0 32,0 32,0 38,0 35,0 38,0 49,0 58,0 55,0 62,0 70,0

Z 13,0 15,0 12,0 18,5 15,0 18,0 28,0 36,0 30,0 32,0 35,0

L1 25,0 31,0 27,0 34,0 34,0 33,0 45,0 53,0 47,0 51,0 63,0

Dimension 12 x Rp1/2 15 x Rp1/2 18 x Rp1/2 18 x Rp3/4 22 x Rp3/4 22 x Rp1 28 x Rp1 35 x Rp1 1/4 42 x Rp1 1/2 54 x Rp 2

Article No. 480283.1 480284.2 480285.3 480286.4 480287.5 480288.6 480289.7 480290.8 480291.9 480292.1

L 49,0 53,0 55,0 61,0 62,0 66,0 68,0 75,0 85,0 99,0

Z 32,0 33,0 35,0 41,0 41,0 45,0 45,0 49,0 55,0 64,0

L1 32,0 32,0 32,0 36,0 36,0 40,0 43,6 50,0 53,0 64,0

Z1 17,0 17,0 17,0 20,0 20,0 21,0 25,0 28,0 32,0 38,0

G 3/4 3/4 3/4 1 1 1 1 1/4 1 1/2 1 3/4 2 3/8

A/F 30,0 30,0 30,0 36,0 36,0 36,0 46,0 52,0 58,0 75,0

A/F1 27,0 27,0 27,0 33,0 33,0 40,0 40,0 50,0 56,0 68,0

Providing suitable solutions

237

Copper

238

6.4

6090G Angle adapter 90°

6359 Coupling with flat seal

(press x female thread)

(press x female thread)

Dimension 12 x Rp3/8 12 x Rp1/2 15 x Rp3/8 15 x Rp1/2 15 x Rp3/4 18 x Rp1/2 18 x Rp3/4 22 x Rp1/2 22 x Rp3/4 28 x Rp1 35 x Rp1 1/4 42 x Rp1 1/2 54 x Rp2

Article No. 480147.8 480148.9 480149.1 480150.0 480557.0 480151.1 480152.2 480153.3 480154.4 480155.5 480156.6 480157.7 480158.8

L 32,0 34,0 33,0 41,0 36,0 36,0 38,0 53,0 45,0 51,0 55,0 85,0 104,0

Z 15,0 17,0 13,0 20,0 16,0 16,0 18,0 32,0 24,0 28,0 29,0 57,0 72,0

L1 23,0 23,0 24,0 24,0 70,0 30,0 30,0 24,0 27,0 33,0 45,0 45,0 54,0

Z1 10,0 7,0 11,0 15,0 16,0 14,0 12,0 13,0 11,0 14,0 21,0 26,0 33,0

Dimension 15 x G 3/4 18 x G 3/4 22 x G 1 28 x G1 1/4 35 x G1 1/2 42 x G1 3/4

Article No. 480023.5 480024.6 480025.7 480026.8 480027.9 480028.1

L 25,0 28,0 29,0 31,0 32,0 39,0

Z 5,0 8,0 8,0 8,0 6,0 9,0

A/F 30,0 30,0 36,0 46,0 52,0 58,0

Providing suitable solutions

239

Copper

240

6.4

6330 Straight union

6331G Straight union

(2 x press)

(press x male thread)

Dimension 15 x 15 18 x 18 22 x 22 28 x 28 35 x 35 42 x 42 54 x 54

Article No. 480334.8 480335.9 480336.1 480337.0 480338.1 480339.2 480340.3

L 60,0 62,0 68,0 73,0 71,0 91,0 98,0

Z 20,0 22,0 26,0 27,0 19,0 31,0 28,0

G 3/4 3/4 1 1 1/4 1 1/2 1 3/4 2 3/8

A/F 30,0 30,0 36,0 46,0 52,0 58,0 75,0

A/F1 25,0 25,0 32,0 40,0 46,0 51,0 65,0

Dimension 12 x R3/8 12 x R1/2 15 x R1/2 15 x R 3/4 18 x R1/2 18 x R3/4 22 x R1/2 22 x R3/4 22 x R1 28 x R3/4 28 x R1 35 x R1 1/4 42 x R1 1/2 54 x R2

Article No. 480257.8 480258.9 480259.1 480260.0 480261.1 480262.2 480263.3 480264.4 480265.5 480556.1 480266.6 480267.7 480268.8 480269.9

L 48,0 54,0 62,0 58,0 59,0 61,0 66,0 74,0 68,0 75,0 76,0 79,0 88,0 101,0

Z 31,0 37,0 42,0 38,0 39,0 41,0 45,0 53,0 47,0 52,0 53,0 53,0 58,0 66,0

G 1/2 3/4 3/4 3/4 3/4 3/4 1 1 1 1 1 1/4 1 1/2 1 3/4 2 3/8

A/F 24,0 30,0 30,0 30,0 30,0 30,0 36,0 36,0 36,0 46,0 46,0 52,0 58,0 75,0

A/F1 19,0 25,0 25,0 25,0 25,0 25,0 32,0 32,0 32,0 40,0 40,0 46,0 51,0 65,0

Providing suitable solutions

241

Copper

242

6.4

6330G Straight union

6472G Wallplate 90°

(press x female thread)

(press x female thread)

Dimension 12 x Rp1/2 15 x Rp1/2 15 x Rp3/4 18 x Rp1/2 18 x Rp3/4 22 x Rp3/4 22 x Rp1 28 x Rp3/4 28 x Rp1 35 x Rp1 1/4 42 x Rp1 1/2 54 x Rp2

6490

Article No. 480272.1 480273.2 480274.3 480275.4 480276.5 480277.6 480278.7 480555.9 480279.8 480280.9 480281.1 480282.0

L 42,0 52,0 55,0 48,0 57,0 68,0 65,0 65,0 65,0 74,0 83,0 90,0

Z 10,0 30,0 18,0 13,0 21,0 43,0 25,0 28,0 43,0 52,0 48,0 50,0

G 3/4 3/4 3/4 3/4 3/4 1 1 1 1 1/4 1 1/2 1 3/4 2 3/8

A/F 30,0 30,0 30,0 30,0 30,0 36,0 36,0 46,0 46,0 52,0 58,0 75,0

A/F1 26,0 26,0 31,0 26,0 31,0 32,0 39,0 31,0 43,0 48,0 53,0 65,0

Dimension

Article No.

L

Z

L1

Z1

L2

12 x Rp1/2 15 x Rp3/8 15 x Rp1/2 18 x Rp1/2 22 x Rp3/4

480087.3 480770.4 480088.4 480089.5 480090.6

61,0 41,0 41,0 41,0 45,0

44,0 21,0 21,0 21,0 24,0

35,0 49,0 36,0 39,0 45,0

7,0 14,0 8,0 9,0 11,0

22,0 36,0 23,0 24,0 27,0

Dist. holes 40,0 40,0 40,0 40,0 40,0

6472L Wallplate 90° long (press x female thread)

Double wall plate

(press x female thread) Dimension 15 x Rp3/8 15 x Rp1/2

Article No. 480750.6 480751.7

Centr. distance 120,0 153,0 Dimension

Article No. L

15 x Rp1/2

480091.7

41,0

Z 21,0

L1 58,0

Z1 8,0

L2 45,0

Dist. holes 40,0

Providing suitable solutions

243

Copper

244

7510 Flanged connector PN 10/16

7240 Reducer

(1 x press)

(2 x press)

Dimension Ø67(DN65) Ø76,1(DN65) Ø88,9(DN80) Ø108(DN100)

Article No. 480637.3 480638.4 480639.5 480640.6

L Z L1 D1 103,0 53,0 100,0 145,0 103,0 53,0 115,0 145,0 113,0 51,0 135,0 160,0 126,0 59,0 158,0 180,0

D2 D3 holes 185,0 18,0 4 185,0 18,0 4 200,0 18,0 8 220,0 18,0 8

Dimension 15 x 12 22 x 15 28 x 15 28 x 22 35 x 28 42 x 35 54 x 42

6.4

Article No. 480558.1 480559.2 480564.7 480560.3 480561.4 480562.5 480563.6

L

Z 44,0 52,0 59,0 54,0 60,0 67,0 80,0

7,0 11,0 16,0 10,0 11,0 11,0 15,0

7520 Flanged connector PN 10/16 (1 x male)

Dimension 76,1(DN65) 108(DN100)

Article No. L 480643.9 113,0 480651.6 141,0

L1 115,0 158,0

D1 145,0 180,0

D2 185,0 220,0

D3 18,0 18,0

holes 4 8

Providing suitable solutions

245

Copper

246

6131G Female branch tee with multi ports

S302 Stop end

(2 x press)

(1 x male)

Dimension 67 x Rp1/2 76,1 x Rp1/2 88,9 x Rp3/4 108 x Rp3/4

Article No. 480305.1 480306.2 480307.3 480308.4

a b Za A B C D 130,0 84,0 29,0 1/2” 1/2” 130,0 96,0 28,0 1/2” 1/2” 160,0 108,0 36,0 3/4” 3/4” 3/4” 170,0 132,0 35,0 3/4” 3/4” 3/4” 3/4”

Dimension 35 42 54

6.4

Article No. 480144.5 480145.6 480146.7

L 96,0 108,0 125,0

Providing suitable solutions

247

Copper

248

7301 Stop end

7999 O-ring standard

(1 x press)

(black, EPDM) for copper

Dimension 12 15 18 22 28 35 42 54 67 76,1 88,9 108

Article No. 480570.2 480294.1 480295.2 480296.3 480297.4 480298.5 480299.6 480300.7 480634.0 480302.9 480635.1 480304.0

L 17,0 20,0 20,0 21,0 23,0 26,0 30,0 35,0 50,0 50,0 62,0 67,0

Dimension 12 15 18 22 28 35 42 54 64 67 76,1 88,9 108

6.4

Article No. 611590.1 611591.2 611592.3 611593.4 611594.5 611595.6 611596.7 611597.8 480506.4 480652.7 480507.5 480508.6 480509.7

249

Providing suitable solutions

Copper

6.4 6.5

C 1700 O-ring special (green, Viton®) for copper Dimension 15 18 22 28 35 42 54 76,1 88,9 108

Article No. 480521.8 480522.9 480523.1 480524.0 480525.1 480526.2 480527.3 611937.7 611938.8 611939.9

VSH 6 Product range

250

251

S1283 Insert stiffener for Wicu tube

6.5 XPress Copper GAS

(male)

Dimension 12 x 1,0 15 x 1,0 18 x 1,0 22 x 1,0 28 x 1,2

Article No. 088323.4 088324.5 088327.8 088329.1 088330.0

B 23,0 23,0 25,0 27,0 32,0

D1 12 15 18 22 22

D2 9,8 12,5 15,8 19,8 25,4

Providing suitable solutions

Copper GAS

252

6.5

G7270 Straight coupling

G7270S Slip coupling

(2 x press)

(2 x press)

Dimension 15 x 15 18 x 18 22 x 22 28 x 28 35 x 35 42 x 42 54 x 54

Article No. 480443.7 480444.8 480445.9 480446.1 480447.0 480448.1 480449.2

L 43,0 44,0 46,0 50,0 62,0 71,0 83,0

Z 3,0 4,0 4,0 4,0 6,0 7,0 9,0

Dimension 15 x 15 18 x 18 22 x 22 28 x 28 35 x 35 42 x 42 54 x 54

Article No. 480450.3 480451.4 480452.5 480453.6 480454.7 480455.8 480456.9

L

Z 80,0 80,0 84,0 91,0 99,0 119,0 141,0

25,0 25,0 25,0 30,0 26,0 30,0 35,0

Providing suitable solutions

253

Copper GAS

254

6.5

G7002A Elbow 90°

G7001A Elbow 90°

(2 x press)

(press x male)

Dimension 15 x 15 18 x 18 22 x 22 28 x 28 35 x 35 42 x 42 54 x 54

Article No. 480383.2 480384.3 480385.4 480386.5 480387.6 480388.7 480389.8

L 38,0 42,0 47,0 57,0 68,0 80,0 100,0

Z 18,0 22,0 26,0 34,0 42,0 50,0 65,0

r 18,0 22,0 26,0 34,0 42,0 50,0 65,0

Dimension 15 x Ø15 18 x Ø18 22 x Ø22 28 x Ø28 35 x Ø35 42 x Ø42 54 x Ø54

Article No. 480376.6 480377.7 480378.8 480379.9 480380.1 480381.0 480382.1

L 36,0 42,0 47,0 58,0 69,0 81,0 100,0

Z 18,0 22,0 26,0 34,0 44,0 52,0 66,0

L1 51,0 53,0 60,0 64,0 83,0 101,0 120,0

r 18,0 22,0 26,0 34,0 42,0 50,0 65,0

Providing suitable solutions

255

Copper GAS

256

6.5

G7041 Elbow 45°

G7040 Elbow 45°

(2 x press)

(press x male)

Dimension 15 x 15 18 x 18 22 x 22 28 x 28 35 x 35 42 x 42 54 x 54

Article No. 480397.5 480398.6 480399.7 480400.8 480401.9 480402.1 480403.0

L 28,0 29,0 33,0 41,0 47,0 57,0 68,0

Z 8,0 9,0 14,0 19,0 22,0 28,0 32,0

r 18,0 22,0 26,0 34,0 42,0 50,0 65,0

Dimension 15 x Ø15 18 x Ø18 22 x Ø22 28 x Ø28 35 x Ø35 42 x Ø42 54 x Ø54

Article No. 480390.9 480391.1 480392.0 480393.1 480394.2 480395.3 480396.4

L 28,0 29,0 32,0 37,0 43,0 51,0 62,0

Z 8,0 9,0 11,0 14,0 17,0 21,0 27,0

L1 67,0 39,0 44,0 47,0 58,0 71,0 82,0

r 18,0 22,0 26,0 34,0 42,0 50,0 65,0

Providing suitable solutions

257

Copper GAS

258

6.5

G7086 Crossover

G7087 Crossover

(press x male)

(2 x male)

Dimension 15 x Ø15 18 x Ø18

Article No. 480407.4 480408.5

L 110,0 120,0

Z 90,0 100,0

L1 41,0 45,0

L2 46,0 49,0

L3 26,0 27,0

Dimension Ø15 x Ø15 Ø18 x Ø18 Ø22 x Ø22

Article No. 480078.5 480079.6 480080.7

L 157,0 166,0 178,0

L1 56,0 60,0 65,0

L1 46,0 49,0 55,0

L3 30,0 31,0 33,0

G7085 Crossover (2 x press)

Dimension 15 x 15 18 x 18 22 x 22

Article No. 480404.1 480405.2 480406.3

L 140,0 151,0 169,0

Z 100,0 111,0 127,0

L1 26,0 27,0 28,0

Providing suitable solutions

259

Copper GAS

260

G7130 Tee equal

G7130 Tee reduced

(3 x press)

(3 x press)

Dimension 15 x 15 x 15 18 x 18 x 18 22 x 22 x 22 28 x 28 x 28 35 x 35 x 35 42 x 42 x 42 54 x 54 x 54

Article No. L 480410.7 32,0 480411.8 34,0 480412.9 37,0 480413.1 42,0 480414.0 50,0 480415.1 57,0 480416.2 69,0

Z 12,0 14,0 16,0 19,0 24,0 27,0 34,0

L1 32,0 34,0 37,0 42,0 50,0 63,0 78,0

Z1 12,0 14,0 16,0 19,0 24,0 33,0 43,0

Dimension 18 x 15 x 18 22 x 15 x 22 22 x 15 x 15 22 x 18 x 22 22 x 22 x 15 28 x 15 x 28 28 x 18 x 28 28 x 22 x 28 35 x 22 x 35 35 x 28 x 35 42 x 22 x 42 42 x 28 x 42 42 x 35 x 42 54 x 22 x 54 54 x 42 x 54

Article No. 480417.3 480419.5 480418.4 480420.6 480421.7 480422.8 480423.9 480424.1 480425.0 480426.1 480763.8 480427.2 480428.3 480764.9 480429.4

6.5

L 34,0 37,0 37,0 37,0 37,0 42,0 42,0 42,0 45,0 50,0 50,0 56,0 57,0 60,0 69,0

Z 14,0 16,0 16,0 16,0 16,0 19,0 19,0 19,0 19,0 24,0 20,0 26,0 27,0 25,0 34,0

L1 35,0 38,0 38,0 38,0 37,0 40,5 40,5 41,0 44,0 44,0 48,0 49,0 56,0 54,0 64,0

Z1 15,0 18,0 18,0 18,0 16,0 21,0 21,0 20,0 23,0 21,0 27,0 26,0 33,0 33,0 34,0

L2 34,0 37,0 43,0 37,0 46,0 42,0 42,0 42,0 45,0 50,0 50,0 56,0 57,0 60,0 69,0

Z2 14,0 16,0 23,0 16,0 26,0 19,0 19,0 19,0 19,0 24,0 20,0 26,0 27,0 25,0 34,0

Providing suitable solutions

261

Copper GAS

262

6.5

G6130G Tee threaded

G7243 Reducer

(press x female thread x press)

(male x press)

Dimension 15 x Rp1/2 x 15 18 x Rp1/2 x 18 22 x Rp1/2 x 22 22 x Rp3/4 x 22 28 x Rp1/2 x 28 28 x Rp3/4 x 28 35 x Rp1/2 x 35 35 x Rp1 x 35 42 x Rp1/2 x 42 54 x Rp1/2 x 54

Article No. 480483.3 480484.4 480485.5 480486.6 480487.7 480488.8 480489.9 480490.1 480491.0 480493.2

L 32,0 34,0 37,0 37,0 42,0 42,0 50,0 50,0 57,0 69,0

Z 12,0 14,0 16,0 16,0 19,0 19,0 24,0 24,0 37,0 34,0

L1 59,0 62,0 65,0 67,0 68,0 69,0 69,0 75,0 81,0 86,0

Z1 44,0 47,0 50,0 51,0 53,0 52,0 54,0 56,0 66,0 71,0

Dimension Ø18 x 15 Ø22 x 15 Ø22 x 18 Ø28 x 15 Ø28 x 18 Ø28 x 22 Ø35 x 22 Ø35 x 28 Ø42 x 22 Ø42 x 28 Ø42 x 35 Ø54 x 28 Ø54 x 35 Ø54 x 42

Article No. 480430.5 480431.6 480432.7 480433.8 480434.9 480435.1 480436.0 480437.1 480438.2 480439.3 480440.4 480728.6 480441.5 480442.6

L 47,0 54,0 48,0 62,0 59,0 55,0 68,0 66,0 76,0 73,0 75,0 89,0 90,0 89,0

Z 25,0 34,0 26,0 42,0 37,0 34,0 47,0 44,0 55,0 48,0 48,0 67,0 63,0 58,0

D 18,0 22,0 22,0 28,0 28,0 28,0 35,0 35,0 42,0 42,0 42,0 54,0 54,0 54,0

D1 15 15 18 15 18 22 22 28 22 28 35 42 35 42

Providing suitable solutions

263

Copper GAS

264

6.5

G6243G Straight connector

G6270G Straight connector

(press x male thread)

(press x female thread)

Dimension 15 x R1/2 15 x R3/4 18 x R1/2 18 x R3/4 22 x R1/2 22 x R3/4 22 x R1 28 x R3/4 28 x R1 28 x R1 1/4 35 x R1 35 x R1 1/4 42 x R1 1/4 42 x R1 1/2 54 x R2

Article No. 480341.4 480342.5 480343.6 480344.7 480345.8 480346.9 480347.1 480348.0 480349.1 480350.2 480351.3 480352.4 480353.5 480354.6 480355.7

L 37,0 39,0 37,0 39,0 38,0 40,0 42,0 43,0 44,0 48,0 48,0 50,0 58,0 58,0 63,0

Z 17,0 19,0 17,0 19,0 17,0 19,0 21,0 20,0 21,0 25,0 22,0 24,0 28,0 28,0 28,0

A/F 21,0 25,0 25,0 25,0 30,0 30,0 32,0 36,0 36,0 40,0 41,0 41,0 51,0 51,0 63,0

Dimension 15 x Rp1/2 15 x Rp3/4 18 x Rp1/2 18 x Rp3/4 22 x Rp1/2 22 x Rp3/4 28 x Rp1 35 x Rp1 1/4 42 x Rp1 1/2 54 x Rp2

Article No. 480356.8 480357.9 480358.1 480359.0 480360.1 480361.2 480362.3 480363.4 480364.5 480365.6

L 38,0 39,0 37,0 39,0 37,0 39,0 45,0 50,0 54,0 63,0

Z 3,0 3,0 2,0 3,0 1,0 2,0 2,0 1,0 2,0 2,0

A/F 25,0 30,0 25,0 30,0 30,0 30,0 37,0 46,0 53,0 65,0

Providing suitable solutions

265

Copper GAS

6280G

Straight connector

6246G

(male x male thread)

266

Dimension 15 x R1/2 18 x R1/2 18 x R3/4 22 x R1/2 22 x R3/4 28 x R1 35 x R1 1/4 42 x R1 1/2

Article No. 480325.1 480326.0 480327.1 480328.2 480329.3 480330.4 480331.5 480332.6

6.5

Straight connector

(male x female thread)

L 50,0 50,0 53,0 51,0 52,0 57,0 63,0 80,0

A/F 19,0 19,0 25,0 25,0 25,0 32,0 40,0 46,0

Dimension 15 x Rp1/2 18 x Rp1/2 18 x Rp3/4 22 x Rp1/2 22 x Rp3/4 28 x Rp3/4 28 x Rp1 35 x Rp1 35 x Rp1 1/4 42 x Rp1 1/2 54 x Rp2

Article No. 480311.7 480312.8 480313.9 480314.1 480315.0 480316.1 480317.2 480318.3 480319.4 480320.5 480321.6

L 47,0 47,0 49,0 46,0 49,0 50,0 54,0 56,0 60,0 76,0 86,0

Z 32,0 32,0 33,0 31,0 32,0 34,0 35,0 37,0 38,0 55,0 60,0

A/F 25,0 25,0 30,0 25,0 30,0 30,0 37,0 37,0 46,0 53,0 65,0

Providing suitable solutions

267

Copper GAS

268

6.5

G6092G Angle adapter 90°

G6090G Angle adapter 90°

(press x male thread)

(press x female thread)

Dimension 15 x R1/2 18 x R1/2 18 x R3/4 22 x R3/4 28 x R1 35 x R1 1/4 42 x R1 1/2 54 x R2

Article No. 480475.6 480476.7 480477.8 480478.9 480479.1 480480.0 480481.1 480482.2

L 38,0 35,0 38,0 49,0 58,0 55,0 62,0 70,0

Z 15,0 15,0 18,0 27,0 35,0 29,0 32,0 35,0

L1 31,0 34,0 33,0 44,0 53,0 47,0 51,0 63,0

Dimension 15 x Rp1/2 15 x Rp3/4 18 x Rp1/2 18 x Rp3/4 22 x Rp1/2 22 x Rp3/4 22 x Rp1 28 x Rp1 35 x Rp1 1/4 42 x Rp1 1/2 54 x Rp2

Article No. 480464.6 480465.7 480466.8 480467.9 480468.1 480469.0 480470.1 480471.2 480472.3 480473.4 480474.5

L 36,0 38,0 36,0 38,0 53,0 45,0 69,0 51,0 55,0 67,0 74,0

Za 16,0 18,0 16,0 18,0 32,0 24,0 38,0 28,0 29,0 37,0 39,0

L1 26,0 30,0 30,0 30,0 24,0 27,0 49,0 33,0 45,0 52,0 60,0

Z1 10,0 12,0 14,0 12,0 13,0 11,0 21,0 14,0 21,0 26,0 33,0

Providing suitable solutions

269

Copper GAS

270

6.5

G6340 Straight union

G6472G Wallplate 90°

(2 x press)

(press x female thread)

Dimension 15 18 22 28 35 42 54

Article No. 480366.7 480367.8 480368.9 480369.1 480370.0 480371.1 480372.2

L 61,0 67,0 66,0 75,0 82,0 97,0 103,0

Z 21,0 27,0 24,0 29,0 30,0 37,0 33,0

G 7/8 1 1/8 1 1/8 1 3/8 1 3/4 1 3/4 1 3/4

A/F 34,0 41,0 41,0 48,0 58,0 65,0 80,0

A/F1 28,0 36,0 36,0 41,0 50,0 55,0 70,0

Dimension

Article No.

15 x Rp1/2 18 x Rp1/2 22 x Rp3/4

480495.4 480496.5 480497.6

L

Z 41,0 41,0 45,0

21,0 21,0 24,0

L1 36,0 39,0 45,0

Z1

L2

8,0 9,0 11,0

23,0 24,0 27,0

Dist. holes 40,0 40,0 40,0

G6360 Coupling with nut (press x female thread)

Dimension 15 x Rp7/8 22 x Rp1 1/8 28 x Rp1 3/8

Article No. 480373.3 480374.4 480375.5

a 29,0 34,0 41,0

Z 9,0 13,0 18,0

A/F 34,0 41,0 48,0 Providing suitable solutions

271

Carbon steel

6.3 6.6

G7301 Stop end (1 x press)

VSH 6 Product range 272

Dimension 15 18 22 28 35 42 54

Article No. 480457.1 480458.0 480459.1 480460.2 480461.3 480462.4 480463.5

L 20,0 20,0 21,0 23,0 26,0 30,0 35,0

273

6.6 XPress Copper Solar

G7999 O-ring standard (yellow, NBR) for copper GAS

Dimension 15 18 22 28 35 42 54

Article No. 480510.8 480511.9 480512.1 480513.0 480514.1 480515.2 480516.3

Providing suitable solutions

Copper Solar

274

6.6

S7270 Straight coupling

S7270S Slip coupling

(2 x press)

(2 x press)

Dimension 15 x 15 22 x 22 28 x 28 35 x 35 42 x 42 54 x 54

Article No. 480800.1 480801.2 480802.3 480803.4 480804.5 480805.6

L

Z 43,0 46,0 50,0 62,0 71,0 83,0

3,0 4,0 4,0 6,0 7,0 9,0

Dimension 15 x 15 22 x 22 28 x 28 35 x 35 42 x 42 54 x 54

Article No. 480806.7 480807.8 480808.9 480809.1 480810.0 480811.1

L

Z 80,0 84,0 91,0 99,0 119,0 141,0

25,0 25,0 30,0 26,0 30,0 35,0

Providing suitable solutions

275

Copper Solar

276

6.6

S7002A Elbow 90°

S7001A Elbow 90°

(2 x press)

(press x male)

Dimension 15 x 15 22 x 22 28 x 28 35 x 35 42 x 42 54 x 54

Article No. 480841.9 480842.1 480843.0 480844.1 480845.2 480846.3

L 38,0 47,0 56,0 68,0 80,0 100,0

Z

r 17,0 26,0 34,0 42,0 50,0 65,0

18,0 26,0 34,0 42,0 50,0 65,0

Dimension 15 x Ø15 22 x Ø22 28 x Ø28 35 x Ø35 42 x Ø42 54 x Ø54

Article No. L 480847.4 36,0 480848.5 47,0 480849.6 58,0 480850.7 69,0 480851.8 81,0 480852.9 100,0

Z 16,0 27,0 34,0 44,0 52,0 66,0

L1 50,0 58,0 64,0 82,0 101,0 120,0

r 18,0 26,0 34,0 42,0 50,0 65,0

Providing suitable solutions

277

Copper Solar

278

6.6

S7041 Elbow 45°

S7040 Elbow 45°

(2 x press)

(press x male)

Dimension 15 x 15 22 x 22 28 x 28 35 x 35 42 x 42 54 x 54

Article No. 480867.2 480868.3 480869.4 480870.5 480871.6 480872.7

L

Z 28,0 33,0 41,0 47,0 57,0 68,0

r 8,0 14,0 19,0 22,0 28,0 32,0

18,0 26,0 34,0 42,0 50,0 65,0

Dimension 15 x Ø15 22 x Ø22 28 x Ø28 35 x Ø35 42 x Ø42 54 x Ø54

Article No. L 480873.8 28,0 480874.9 32,0 480875.1 37,0 480876.0 43,0 480877.1 51,0 480878.2 62,0

Z 8,0 11,0 14,0 17,0 21,0 27,0

L1 37,0 44,0 47,0 58,0 71,0 82,0

r 18,0 26,0 34,0 42,0 50,0 65,0

Providing suitable solutions

279

Copper Solar

280

6.6

S7130 Tee equal

S7130 Tee reduced

(3 x press)

(3 x press)

Dimension 15 x 15 x 15 22 x 22 x 22 28 x 28 x 28 35 x 35 x 35 42 x 42 x 42 54 x 54 x 54

Article No. L 480879.3 32,0 480880.4 37,0 480881.5 42,0 480882.6 50,0 480883.7 58,0 480884.8 69,0

Z 12,0 16,0 19,0 24,0 28,0 34,0

L1 32,0 37,0 42,0 50,0 58,0 69,0

Z1 12,0 16,0 19,0 24,0 28,0 34,0

Dimension 15 x 22 x 15 22 x 15 x 22 28 x 15 x 28 28 x 22 x 28 35 x 15 x 35 35 x 22 x 35 35 x 28 x 35 42 x 15 x 42 42 x 22 x 42 42 x 28 x 42 42 x 35 x 42 54 x 22 x 54 54 x 28 x 54 54 x 35 x 54 54 x 42 x 54

Article No. 480910.1 480885.9 480886.1 480887.0 480888.1 480889.2 480890.3 480891.4 480892.5 480893.6 480894.7 480895.8 480896.9 480897.1 480898.0

L

Z 32,0 37,0 42,0 42,0 45,0 49,0 50,0 50,0 50,0 56,0 56,0 60,0 60,0 67,0 69,0

12,0 16,0 19,0 19,0 19,0 23,0 24,0 20,0 20,0 26,0 26,0 25,0 25,0 36,0 34,0

L1 34,0 38,0 40,5 41,0 44,0 44,0 44,0 47,5 47,5 49,0 50,0 53,5 55,0 66,0 64,0

Z1 18,0 18,0 21,0 20,0 24,0 23,0 21,0 28,0 27,0 26,0 24,0 33,0 32,0 25,0 34,0

Providing suitable solutions

281

Copper Solar

282

6.6

S7130 Tee reduced

S7243 Reducer

(3 x press)

(male x press)

Dimension 22 x 22 x 15 28 x 28 x 15 28 x 28 x 22 35 x 35 x 22 35 x 35 x 28

Article No. 480899.1 480900.2 480901.3 480902.4 480903.5

L 37,0 42,0 42,0 51,0 51,0

Z 16,0 19,0 19,0 25,0 25,0

L1 37,0 42,0 42,0 50,0 50,0

Z1 16,0 19,0 19,0 25,0 25,0

L2 46,0 42,0 52,0 51,0 51,0

Z2 26,0 31,0 31,0 51,0 45,0

L 37,0 42,0 42,0 51,0 51,0 51,0

Z 16,0 19,0 19,0 25,0 25,0 25,0

L1 44,0 41,0 41,0 44,0 44,0 44,0

Z1 18,0 21,0 20,0 23,0 23,0 21,0

L2 43,0 49,0 48,5 67,0 63,0 67,0

Z2 23,0 28,0 28,0 45,0 40,0 44,0

S7130 Tee reduced (3 x press)

Dimension 22 x 15 x 15 28 x 15 x 22 28 x 22 x 22 35 x 22 x 22 35 x 22 x 28 35 x 28 x 28

Article No. 480904.1 480905.7 480906.8 480907.9 480908.1 480909.0

Dimension Ø22 x 15 Ø28 x 15 Ø28 x 22 Ø35 x 22 Ø35 x 28 Ø42 x 22 Ø42 x 28 Ø42 x 35 Ø54 x 28 Ø54 x 35 Ø54 x 42

Article No. 480824.3 480825.4 480826.5 480827.6 480828.7 480829.8 480830.9 480831.1 480832.0 480833.1 480834.2

L

Z 54,0 62,0 56,0 68,0 66,0 76,0 73,0 75,0 89,0 90,0 89,0

d 34,0 42,0 34,4 47,0 44,0 55,0 48,0 48,0 67,0 63,0 58,0

d1 22,0 28,0 28,0 35,0 35,0 42,0 42,0 42,0 54,0 54,0 54,0

15 15 22 22 28 22 28 35 28 35 42

Providing suitable solutions

283

Copper Solar

284

6.6

S6130G Tee threaded

S6243G Straight connector

(press x female thread x press)

(press x male thread)

Dimension 15 x Rp1/2 x 15 22 x Rp1/2 x 22 22 x Rp3/4 x 22 28 x Rp1/2 x 28 28 x Rp3/4 x 28 35 x Rp1/2 x 35 42 x Rp1/2 x 42

Article No. 480911.2 480912.3 480913.4 480914.5 480915.6 480916.7 480917.8

L 41,0 42,0 45,0 44,0 41,0 50,0 57,0

Z 21,0 21,0 24,0 21,0 18,0 24,0 27,0

L1 23,0 26,0 27,0 29,0 34,0 34,0 38,0

Z1 11,0 11,0 11,0 14,0 14,0 19,0 23,0

Dimension 15 x R1/2 22 x R3/4 28 x R1 35 x R1 1/4 42 x R1 1/2 54 x R2

Article No. 480818.8 480819.9 480820.1 480821.0 480822.1 480823.2

L

Z 37,0 40,0 44,0 50,0 58,0 63,0

17,0 21,0 21,0 24,0 28,0 28,0

A/F 21,0 30,0 36,0 41,0 51,0 63,0

Providing suitable solutions

285

Copper Solar

S6270G

Straight connector

S6092G Angle adapter 90°

(press x female thread)

286

Dimension 15 x Rp1/2 22 x Rp3/4 28 x Rp1 35 x Rp1 1/4 42 x Rp1 1 /2 54 x Rp2

Article No. 480812.2 480813.3 480814.4 480815.5 480816.6 480817.7

6.6

(press x male thread)

L

Z 38,0 39,0 45,0 50,0 54,0 63,0

3,0 2,0 2,0 1,0 2,0 2,0

A/F 25,0 30,0 37,0 46,0 53,0 65,0

Dimension 15 x R1/2 22 x R3/4 28 x R1 35 x R1 1/4 42 x R1 1/2 54 x R2

Article No. 480853.1 480854.0 480855.1 480856.2 480857.3 480858.4

L 38,0 49,0 58,0 55,0 62,0 70,0

Z 19,0 28,0 36,0 30,0 32,0 35,0

L1 34,0 45,0 53,0 47,0 51,0 63,0

Providing suitable solutions

287

Copper Solar

288

6.6

S6090G Angle adapter 90°

S6330 Straight union

(press x female thread)

(2 x press)

Dimension 15 x Rp1/2 22 x Rp3/4 28 x Rp1 35 x Rp1 1/4 42 x Rp1 1/2 54 x Rp2

Article No. 480859.5 480860.6 480861.7 480862.8 480863.9 480864.1

L 41,0 45,0 51,0 55,0 85,0 104,0

Z 20,0 24,0 28,0 29,0 57,0 72,0

L1 24,0 27,0 33,0 45,0 45,0 54,0

Z1 15,0 11,0 14,0 21,0 26,0 33,0

Dimension 15 x 15 22 x 22 28 x 28 35 x 35 42 x 42 54 x 54

Article No. 480835.3 480836.4 480837.5 480838.6 480839.7 480840.8

L 60,0 68,0 73,0 71,0 91,0 98,0

Z 20,0 26,0 27,0 19,0 31,0 28,0

G 3/4 1 1 1/4 1 1/2 1 3/4 2 3/8

A/F 30,0 36,0 46,0 52,0 58,0 75,0

A/F1 25,0 32,0 40,0 46,0 51,0 65,0

Providing suitable solutions

289

Copper Solar

290

6.6

S6331G Straight union

S6330G Straight union

(press x male thread)

(press x female thread)

Dimension 15 x R1/2 22 x R3/4 28 x R1 35 x R1 1/4 42 x R1 1/2 54 x R2

Article No. 480924.4 480925.5 480926.6 480927.7 480928.8 480929.9

L 62,0 74,0 76,0 79,0 88,0 101,0

Z 42,0 53,0 53,0 53,0 58,0 66,0

G 3/4 1 1 1/4 1 1/2 1 3/4 2 3/8

A/F 30,0 36,0 46,0 52,0 58,0 75,0

A/F1 25,0 32,0 40,0 46,0 51,0 65,0

Dimension 15 x Rp1/2 22 x Rp3/4 28 x Rp1 35 x Rp1 1/4 42 x Rp1 1/2 54 x Rp2

Article No. 480930.1 480931.0 480932.1 480933.2 480934.3 480935.4

L

Z 30,0 43,0 43,0 52,0 48,0 50,0

52,0 68,0 65,0 74,0 83,0 90,0

G 3/4 1 1 1/4 1 1/2 1 3/4 2 3/8

A/F 30,0 36,0 46,0 52,0 58,0 75,0

A/F1 26,0 32,0 43,0 48,0 53,0 65,0

Dist. holes

S6472G Wallplate 90° (press x female thread)

Dimension

Article No.

L

Z

L1

Z1

L2

15 x Rp1/2 22 x Rp3/4

480865.0 480866.1

41,0 45,0

21,0 24,0

36,0 45,0

8,0 11,0

23,0 27,0

40,0 40,0

Providing suitable solutions

291

Copper Solar

6.6 6.7

7 Index

S7301 Stop end (1 x press)

VSH 6 Product range 292

Dimension 15 22 28 35 42 54

Article No. 480918.9 480919.1 480920.0 480921.1 480922.2 480923.3

L 20,0 21,0 23,0 26,0 30,0 35,0

293

6.7 Tools

C 1700 O-ring special (green, Viton®) for copper Dimension 15 18 22 28 35 42 54

Article No. 480521.8 480522.9 480523.1 480524.0 480525.1 480526.2 480527.3

Providing suitable solutions

Carbon steel Tools P 5991/P 5999 Press tool Novopress AFP 101 + jaw +case AFP 101 AFP 101 jaw AFP 101 jaw AFP 101 jaw AFP 101 jaw AFP 101 jaw AFP 101 (9,6 V) battery AFP 101 (9,6 V) charger

Dimension 15-22-28 12-28 12 15 18 22 28

6.3 6.7

P 5990 Press jaws Novopress Article No. 620919.2 620815.8 620920.3 620921.4 620922.5 620923.6 620924.7 620928.0 620930.2

ZB 203 adapter ECOTEC sling ECOTEC sling ECOTEC sling

Dimension 42-54 35 42 54

Article No. 634082.9 624103.7 620579.3 620580.4

Dimension 12-108

Article No. 620570.5

P 5997 Press tool Novopress ECO 301

P 5992/P 5996 Press tool Novopress 294

EFP 2 EFP 202 + case AFP 202 + battery + charger + case AFP 202 + jaws + battery + charger + case AFP 202 + jaws + battery + charger + case ECO 202 + case ECO 202 + jaws + case ACO 202 + battery + charger + case ACO 202 + jaws + battery + charger + case

Dimension 12-54 12-54 12-54

Article No. 620592.5 634064.2 634060.9

12-15-18-2228-35 15-22-28-35

634066.4

12-54 12-15-18-2228-35 12-54

634016.9 634069.7 624141.1

15-22-28-35

634068.6

634066.4

P 5990 Press jaws Novopress ECOTEC jaw ECOTEC jaw ECOTEC jaw ECOTEC jaw ECOTEC jaw ECOTEC jaw

Dimension 12 15 18 22 28 35

Article No. 620533.1 620534.2 620535.3 620536.4 620537.5 620538.6

ECO301 + case

12-108

620550.7

295

P 5989 Press jaws/slings Novopress ECO 301/ACO 3 jaw ECO 301/ACO 3 jaw ECO 301/ACO 3 jaw ECO 301/ACO 3 jaw ECO 301/ACO 3 jaw ECO 301/ACO 3 jaw ZB 302 adapter ECO 301 sling ECO 301 sling ECO 301 sling VSH Power sling VSH Power sling ZB 321 adapter ZB 322 adapter ECO 301 sling ECO 301 sling ECO 301 sling ECO 301 Copper sling

Dimension 12 15 18 22 28 35 35-42-54-64 42 54 64 42 54 76-89-108/1 108/2 76,1 88,9 108 108

Article No. 620572.7 620573.8 620574.9 620575.1 620576.0 620577.1 620585.9 620579.3 620580.4 620581.5 624104.8 624105.9 620586.1 620587.0 620582.6 620583.7 620584.8 620524.3

Providing suitable solutions

Carbon steel Tools K 3297 Press tool Klauke UAP2 battery powered (12 V)

Dimension 12 - 54

Extra battery for UAP2

Article No. 072908.0

072910.2

P 5010 Press jaws Klauke Dimension 12 15

KSP3 KSP3

296

KSP3 KSP3 KSP3 KSP3 KSP3 KSP3

18 22 28 35 42 54

Article No. 620600.2 620601.3 620602.4 620603.5 620604.6 620605.7 620614.5 620618.9

C 1440 Stripping tool for PP-Carbon steel Dimension 15 18 22 28 32-54 For removing the PP coating at the insertion depth

Blades for carbon steel stripping tool

KSP3 KSP3 KSP3 KSP3 KSP3

Article No. 626001.2

Dimension 76,1-108

Article No. 620610.1

626002.3 626003.4

Dimension 15-18 22-28 35-54

Article No. 621201.9 621202.1 621203.0

R 2742 Insertion depth marker

for stainless steel and carbon steel Dimension Adapters for slings 42/54 mm 42 mm (without pressing inserts) 54 mm (without pressing inserts) 76,1 88,9 108

Article No. 621184.3 621185.4 621186.5 621187.6 621188.7

C 1441 Blades for carbon steel stripping tool

P 5014 Press slings Klauke KSP3

6.3 6.7

Dimension 12-54

Article No. 621204.1

Dimension 12-54

Article No. 621189.8

R 2743 Deburr tool

620611.2 620612.3 620613.4

K 3293 Press tool Klauke UAP100 Big Press 230 V

Providing suitable solutions

297