Firmware Update Guide TV 2008 Models v1

■ Applicable models : LCD TV and PDP TV are released on 2008 In case of 2008 New model, there are various methods to S/W upgrade. So, you should check the scaler IC and Model name before S/W update and select the correct upgrade method. Please refer to the below table and each excel sheet.

Data.09.Feb.2009

[ Mstar Scaler model ] - For Europe Ready & SD DTV model (Only 3, 4 Series model, Not MX/WX - Used Mstar Sclaer IC) ※ These model can not support USB Update method and If you use Mstar ISP tool, you need Jig cable for Mstar tool and recommend this method. But, If you use Flashdownloader v5.1, you need DDC manager.

[ MTK Scaler model ] - For Europe Ready & SD DTV model (LE**A5/A6/A7/A900 series, PS**A5/A6 series → XC,XH,XU,XE,,RU,UA,CS,BT Not ZF) - For Europe HD DTV model (LE**A7/A8/A9 series, PS**A7 series → MXXC,MXXH,MXXU,MXZG,MXXQ,MXRU,MXUA,MXCS,MXBT, Not XE) - For France HD DTV model (LE**A4/A5/A6***MXZF, PS**A4/A5/A6***MXZF) - For Nordic HD DTV model (LE**A4/A5/A6/A7/A8/A9***WXXE, PS**A4/A5/A6/A7***WXXE) - For Germany HD DTV model (LE**A6****WXZG) ※ MTK scaler model, If you use MTK tool, you should install MT8226 tool and we recommend USB update method. In case of Europe Ready & SD DTV model , USB S/W upgrdae is for only ATV S/W and not support DTV S/W. But, ~MX & ~WX model(support H264:HD format), If you use USB method, You can update both S/W for Main CPU(DTV) and MTK Scaler. ※ Some of new model didn't follow the below table. To confirm it, Please refer to the next sheet(by full model code). Update method Destination

Product

ATV S/W

Model Flash Downloader V5.1

LCD TV Europe Ready & SD DTV (Only 3, 4 Series model)

USB

MTK Tool

Sv2_v07

CI Card

DTV SW Version

USB Foler Name

LE**A3****(iDTV)

O

O

X

X

O

O

X

T-JDEPEUMD-****

T-PERLDEUC-****

-

LE**A3****(Ready)

O

O

X

X

O

O

X

T-JDEPEUMD-****

-

-

LE**A3****(Nordic)

O

O

X

X

O

O

X

T-JDEPEUMD-****

T-NHBTEDEUC-****

-

LE**A4****(iDTV)

O

O

X

X

O

O

X

T-CRL32PEUMD-****

T-PERLDEUC-****

-

LE**A4****(Ready)

O

O

X

X

O

O

X

T-CRL32PEUMD-****

-

-

LE**A4****(Nordic)

O

O

X

X

O

O

X

T-CRL32PEUMD-****

T-NHBTEDEUC-****

-

LE22A4****(iDTV)

O

O

X

X

O

O

X

T-AMB22PEUMD-****

T-PERLDEUC-****

-

LE**A4****(Ready)

O

O

X

X

O

O

X

T-CRL32PEUMD-****

-

-

LE22A4****(Nordic)

O

O

X

X

O

O

X

T-AMB22PEUMD-****

T-NHBTEDEUC-****

-

PS**A4****(iDTV)

O

O

X

X

O

O

X

T-PRPPEUMD-****

T-PERLDEUC-****

-

PS**A4****(Ready)

O

O

X

X

O

O

X

T-PRPPEUMD-****

-

-

PS**A4****(Nordic)

O

O

X

X

O

O

X

T-PRPPEUMD-****

T-NHBTEDEUC-****

-

LE**A55****(iDTV) LE**A615A3FX(iDTV)

X

X

O

O

O

O

X

T-PRLPEUMD-****

T-PERLDEUC-****

MT8226

LE**A616A3FX(iDTV) LE**A65****X(iDTV) LE**A68****X(iDTV) LE32A756R1FX(iDTV)

LCD TV

X

X

O

O

O

O

X

T-AMBPEUMD-****

T-PERLDEUC-****

MT8226

LE**A900(ARMANI) (iDTV)

X

X

O

O

O

O

X

T-AMNPEUMD-****

T-PERLDEUC-****

MT8226

LE**A786R2FX(iDTV)

X

X

O

O

O

O

X

T-RB2PEUMD-****

T-PERLDEUC-****

MT8226

PS**A5 Series(iDTV)

X

X

O

O

O

O

X T-PRLPEUMD-****

T-PERLDEUC-****

MT8226

PS**A6 Series(iDTV)

X

X

O

O

O

O

X

LE**A4****MXZF

X

X

O

O

X

X

O

LE**A5****MXZF

X

X

O

O

X

X

O T-RBYDEUC-****

-

T-RBYDEU

LE**A6****MXZF

X

X

O

O

X

X

O

LE**A796R2MXZF

X

X

O

O

X

X

O

PDP

Europe HD DTV Model (~~MXXC,MXXH, MXXU,MXZG, MXXQ,MXRU MXUA,MXCS, MXBT)

SW Version

Remark

USB

Not Support USB Update method

PDP

Europe Ready & SD DTV Model (~~XC,XH, XU,XE,RU, UA,CS,BT, not 3 & 4 Series model)

DTV S/W

Mstar ISP Tool

LCD TV

PDP

※ When you unzip the S/W file in USB Memory, folder name is different according to Model Codes. If folder name is different with model code, TV can't find S/W file. Please refer to the USB Update Guide. Recommend DTV S/W update method

PDF Created with deskPDF PDF Writer - Trial :: http://www.docudesk.com

Update Only ATV S/W bu USB method ( Ready : No DTV SW Nordic : Same as 3, 4 Series )

Update both S/W for Main CPU(DTV) and MTK Scaler by USB method

[Flash Downloader V5.1] 1. Flash Downloader V5.1.exe - download and double click, you can install easilly. Flash Downloader V5.1.zip2. porttalk.sys

porttalk.zip

- Procedure to use the application for MStar: . Save the Setup and PortTalk driver on the desktop. . Copy the PortTalk driver and Paste it at the location: C: \ WINDOWS \ System32 \ drivers... . Run the Setup to install Flash Downloader V5.1 and the application is ready to use.

If you need a DDC manager, then order below part code. This is a normal SVC part. MTI-2055 : BH81-90001N (D-sub+DVI) MTI-2059 : BH81-90001P (D-sub+DVI+HDMI)

Connect to Print(LPT1) Port of

Use DDC Manager

Connect to D-sub Port of TV Set

1) Start the "Flash Downloader V5.1"(Must used V5.1), Which is the program only for downloading ATV 2) Connect Download cable to TV set. 3) Turn on TV set. 4) Select Micom Type. (Mstar). 5) Check the Download port. (LPT1)

6) Click "Setting" and select Communication port. (Select LPT1) 7) Click "OK" button, after selected port. 8) Click "Open" button, and select correct file.

PDF Created with deskPDF PDF Writer - Trial :: http://www.docudesk.com

9) Click "Open" button, after selected file.

10) Click "Connect" button and check the "Program" button will activate. 11) Click " Program", Start Download. 12) Finished download, Display "Complet" check it. 13) Exit download program. 14) Remove download cable from TV set.

PDF Created with deskPDF PDF Writer - Trial :: http://www.docudesk.com

[Mstar ISP tool]

M star_Tool.zip

Connect to Download Port on PCB-MAIN

Connect to PC Port of TV Set

Connect to USB Port of PC

[Must check the S/W Position] 1. Use Connect Type like as left figure. (Select S/W position to left) 2. Use D-SUB(PC) Cable like as a right figure. (Select S/W position to right)

1) Connect Download cable to TV and Note-PC.

2) Wait a minute until Note-PC can accept USB device. (The message is showed on left-bottom of screen.) 3) Start the "ISP_Tool", Which is the program only for downloading ATV 4) Click "Connect" icon. 5) Check Device Type. ※ If the program can't find device type, check the 3 below things. - The switch direction on board and light of LED(Only red LED is light when waited to operate.) - Re-connect the cables. - Re-start the ISP_tool program

PDF Created with deskPDF PDF Writer - Trial :: http://www.docudesk.com

6) Click "Read" icon. 7) Click "Read" button, and fine the Download File. 8) Click "Auto" icon. 9) Click "Run" button, Starting download.

If you check the"Blank and Verify" take a long time for Soft download

While the Jig is operated, 3 LED is light

10) Finished download, Display "Pass" check it.

11) Exit download program. 12) Remove download cable from TV set.

PDF Created with deskPDF PDF Writer - Trial :: http://www.docudesk.com

[ MTK Tool ]

20071212_M TKTo ol_2.46.01_Samsung.zip

■ PREPARATION 1. Install MTK Tool for MT8226 in your PC 2. SET Condition > Into 1.Option table → Control in factory mode > Enter In factory Mode of Service Select (Debug/DL) > Enter Stand-By Mode.

3. Start the "MTK Tool" and Click "Chip Type", "Port", "Browse(Download File)"

4. Connect Jig Cable to service port in Main Board.

PDF Created with deskPDF PDF Writer - Trial :: http://www.docudesk.com

■ Download Process 1. SET Power "On" 2. Click "Upgrade Icon" 3. Check "Finishied" 4. Remote control & function key does not work right after upgading new S/W. So turn off TV and turn on. Enter the factory mode. Check if last version is normally updated.

PDF Created with deskPDF PDF Writer - Trial :: http://www.docudesk.com

[ USB Update for SD DTV model ] Applicable models: LCD TV and PDP TV are released on 2008 for SD DTV model. (Not MX or Not WX model) - LE32A756R1FX, LE**A786R2FX, LE**A786R2FX - LE**A900G1FX (ARMANI) - LE**A65****X,LE**A68****X - LE**A61****X, LE**A55****X, PS50A55****X, PS**A65****X

1. Save download file in USB → Creat "MT8226" folder in USB → Unzip new S/W file in "MT8226" folder ※ Caution!! The USB device should have only one folder("MT8226").

Create folder the name is "MT8226" in USB The original file

Unzip the original file into "MT8226" and Check S/W version

2. Insert USB to wiselink terminal when TV is standby mode

PDF Created with deskPDF PDF Writer - Trial :: http://www.docudesk.com

3. Into 1.Option table → Control in factory mode

4. Downloading process → Click "USB SVC" → File search → Do you want upgrade ? Message display → Click "YES" → Upgrading (Do not detach USB equipment) → Download finished

PDF Created with deskPDF PDF Writer - Trial :: http://www.docudesk.com

5. Remote control & function key does not work right after upgading new S/W. So turn off/on TV and enter the factory mode.. Check if last version is normally updated. ※ Remarks : Use Hot key Download > Insert USB memory Stick (with download file) > Push side source key + Remocon power "ON" (Cannot support AC) > until maintain upgrade osd > Upgrade finished : LED toggle and Picture off

※ The file system only supports FAT16/32 (The NTFS file system is not supported) Certain types of USB Digital camera and audio devices may not be compatible with this TV. Wiselink only supports the USB Mass Storage Class device (MSC). MSC is a Mass Storage Class Bulk-Only Transport device. Examples of MSC are Thumb drives and Flash Card Readers (Both USB HDD and HUB are not supported.) Please connect directly to the USB port of your TV. If you are using a separate cable connection, there may be a USB Compatibility problem.

PDF Created with deskPDF PDF Writer - Trial :: http://www.docudesk.com

[ USB Update for HD DTV model ] Applicable models: LCD TV and PDP TV are released on 2008 for HD DTV model. (MX or Not WX model) – For Europe HD DTV model (LE**A7/A8/A9 series, PS**A7 series → MX(XC/XH/XU/ZG/XQ/RU/UA/CS) – For France HD DTV model (LE**A4/A5/A6***MXZF, PS**A4/A5/A6***MXZF) – For Nordic HD DTV model (LE**A4/A5/A6/A7/A8/A9***WXXE, PS**A4/A5/A6/A7***WXXE)

1. Save download file in USB → Unzip in USB, folder name is different according to Model Codes.(Refer to the below) ※ If folder name is different with model code, TV can't find file. Model Name LE**A7/A8/A9*****MX (XC/XH/XU/ZG/XQ/RU/UA/CS) PS**A7*****MX (XC/XH/XU/ZG/XQ/RU/UA/CS) LE**A5/A6*****MXZF PS42A4*****MXZF LE**A7/A8/A9*****WXXE, PS**A7*****WXXE LE**A4*****WXXE, PS**A4*****WXXE LE**A6*****WXZG LE**A4*****MXZF, PS50A4*****MXZF PS**A5*****MXZF, PS**A6*****MXZF LE**A5/A6*****WXXE, PS**A5/A6*****WXXE

Folder Name T-RBYDEU T-AMBDFR T-PRPDFR T-RBYDND T-CRLDND T-AMBDGR T-CRLDFR T-SPNDFR T-AMBDND

※ Caution!! The USB device should have only one folder.

If unzip to folder named according to each models, you can see some files like side picture.

2. Insert USB to wiselink terminal

PDF Created with deskPDF PDF Writer - Trial :: http://www.docudesk.com

3. Downloading process → File search → Setup → SW Upgrade → USB dOwnload → Check Upgrade version → Click "OK" → Upgrading (Do not detach USB equipment) → Download finished → After Download Power will turn off in 3 seconds and turn on again automatically. → Power code off/on

4. Remote control & function key does not work right after upgading new S/W. So turn off/on TV and enter the factory mode.. Check if last version is normally updated.

※ The file system only supports FAT16/32 (The NTFS file system is not supported) Certain types of USB Digital camera and audio devices may not be compatible with this TV. Wiselink only supports the USB Mass Storage Class device (MSC). MSC is a Mass Storage Class Bulk-Only Transport device. Examples of MSC are Thumb drives and Flash Card Readers (Both USB HDD and HUB are not supported.) Please connect directly to the USB port of your TV. If you are using a separate cable connection, there may be a USB Compatibility problem.

PDF Created with deskPDF PDF Writer - Trial :: http://www.docudesk.com

[Sv2_v07]

Sv2_v07.exe

1. Connect the Power cord of the Set (Don't turn on the set yet) 2. Insert the Download Cable(RS232C) to the SERVICE port

3. Execute the program "Sv2_v07.exe" Open the "*.tvz" file and click "Next"

1

4. Click"Next"

5. Click "Next" and then "trigger" messages come out in the trace window.

PDF Created with deskPDF PDF Writer - Trial :: http://www.docudesk.com

6. Turn on the TV set When the set detects a new DTV S/W, some messages come out as follows Then click "Next"

※ Sometimes next message window may come out.

Then click "OK"

7. Click "Next"

8. S/W downloading

PDF Created with deskPDF PDF Writer - Trial :: http://www.docudesk.com

9. After S/W downloading is finished, the upgrading message comes out

10. Completed 11. Check the DTV S/W version (DTV mode > D.Menu > Setup > System > Product Information)

PDF Created with deskPDF PDF Writer - Trial :: http://www.docudesk.com

[ CF CARD (CI Slot) ] 1. SET Condition : Enter Stand-By Mode. 2. Save download file in CF Card → File Type : ******.tvz 3. Insert CF Card to CI Slot 4. SET Power "ON" 5. Upgrading (SET Condition : Video Display, LED "off") 6. Download Finished and Set auto turn off/on. 7. LED Toggle (0.5 sec cycle)

Download Finished (LED toggle)

Downloading (LED off)

8. Remote control & function key does not work right after upgading new S/W. So turn off/on TV and enter the factory mode.. Check if last version is normally updated. ※ Check last version → into Factory or into DTV → D.Menu (Direct Key : subttle + factory)

PDF Created with deskPDF PDF Writer - Trial :: http://www.docudesk.com