Fdd Lte Bts Parameters Lte16a

LTE Radio Access, Rel. FDD-LTE 16A, Operating Documentation, Issue 02

FDD-LTE BTS Parameters DN09147584 Issue 06C Approval Date 2016-08-19

The information in this document applies solely to the hardware/software product (“Product”) specified herein, and only as specified herein. This document is intended for use by Nokia Solutions and Networks' customers (“You”) only, and it may not be used except for the purposes defined in the agreement between You and Nokia Solutions and Networks (“Agreement”) under which this document is distributed. No part of this document may be used, copied, reproduced, modified or transmitted in any form or means without the prior written permission of Nokia Solutions and Networks. If you have not entered into an Agreement applicable to the Product, or if that Agreement has expired or has been terminated, You may not use this document in any manner and You are obliged to return it to Nokia Solutions and Networks and destroy or delete any copies thereof. The document has been prepared to be used by professional and properly trained personnel, and You assume full responsibility when using it. Nokia Solutions and Networks welcome Your comments as part of the process of continuous development and improvement of the documentation. This document and its contents are provided as a convenience to You. Any information or statements concerning the suitability, capacity, fitness for purpose or performance of the Product are given solely on an “as is” and “as available” basis in this document, and Nokia Solutions and Networks reserves the right to change any such information and statements without notice. Nokia Solutions Networks has made all reasonable efforts to ensure that the content of this document is adequate and free of material errors and omissions, and Nokia Solutions and Networks will correct errors that You identify in this document. But, Nokia Solutions and Networks' total liability for any errors in the document is strictly limited to the correction of such error(s). Nokia Solutions and Networks does not warrant that the use of the software in the Product will be uninterrupted or error-free. NO WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY OF AVAILABILITY, ACCURACY, RELIABILITY, TITLE, NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS MADE IN RELATION TO THE CONTENT OF THIS DOCUMENT. IN NO EVENT WILL NOKIA SOLUTIONS AND NETWORKS BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT, EVEN IN THE CASE OF ERRORS IN OR OMISSIONS FROM THIS DOCUMENT OR ITS CONTENT. This document is Nokia Solutions and Networks’ proprietary and confidential information, which may not be distributed or disclosed to any third parties without the prior written consent of Nokia Solutions and Networks. Nokia is a registered trademark of Nokia Corporation. Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for identification purposes only. Copyright © 2015 Nokia Solutions and Networks. All rights reserved. Important Notice on Product Safety This product may present safety risks due to laser, electricity, heat, and other sources of danger. Only trained and qualified personnel may install, operate, maintain or otherwise handle this

distributed or disclosed to any third parties without the prior written consent of Nokia Solutions and Networks. Nokia is a registered trademark of Nokia Corporation. Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for identification purposes only. Copyright © 2015 Nokia Solutions and Networks. All rights reserved. Important Notice on Product Safety This product may present safety risks due to laser, electricity, heat, and other sources of danger. Only trained and qualified personnel may install, operate, maintain or otherwise handle this product and only after having carefully read the safety information applicable to this product. The safety information is provided in the Safety Information section in the “Legal, Safety and Environmental Information” part of this document or documentation set. Nokia Solutions and Networks is continually striving to reduce the adverse environmental effects of its products and services. We would like to encourage you as our customers and users to join us in working towards a cleaner, safer environment. Please recycle product packaging and follow the recommendations for power use and proper disposal of our products and their components. If you should have questions regarding our Environmental Policy or any of the environmental services we offer, please contact us at Nokia Solutions and Networks for any additional information.

A, Operating

Product”) specified

ou”) only, and it may not Solutions and Networks may be used, copied, permission of Nokia e Product, or if that any manner and You copies thereof.

personnel, and You ur comments as part of

tion or statements ct are given solely on orks reserves the right works has made all of material errors and this document. But, limited to the correction software in the Product

UT NOT LIMITED TO RINGEMENT, RELATION TO THE NETWORKS BE ECT, INDIRECT, TED TO LOSS OF R DATA THAT MAY EN IN THE CASE OF

mation, which may not be a Solutions and

ned in this document ation purposes only.

sources of

e handle this

a Solutions and

ned in this document ation purposes only.

sources of

e handle this o this product.

al, Safety and

mental effects of its s to join us in working the recommendations

ronmental services we tion.

1. Introduction

The purpose of this document is to assist users in finding parameters, their meanings, specifications, and default values. Th managed objects and parameters are listed in alphabetical order.

2. How to read this excel report

The excel report provides a full information on the parameter dictionary. It shows the full set of parameter attributes includin the change information. The excel report consists of two main sections: - MO Class Tree - Parameter List

2. 1 MO Class Tree This section shows the full Managed Object Class tree with the names of classes. Rows are grouped into respective class levels for structured and convenient view. Use unfold (+) and fold (-) buttons in the left panel to browse the tree.

2.2 Parameter List This section shows the full parameter information including the following: - abbreviated names - managed objects - parent/child parameter relationships - default values - range and step - field descriptions - change information

2.2.1 Field descriptions Field descriptions are provided in the second row of Parameter List section. Use fold (-) and unfold (+) buttons on the left p to respectively hide and show the field descriptions. 2.2.2 Change information Change information is a part of Parameter List section and is available in the following ways:

1. Definition on whether the parameter is new, removed, changed, or has been moved to another location in the structure (f example, to another managed object class). That definition is provided in the following columns: - Changes between issues ... which shows the changes since the previous issue of the document. - Changes between releases ... which shows the changes since the latest issue of the document in the previous product release. If the cell is empty, the parameter is not changed, nor new, nor removed, nor moved. Note that removed parameters are listed in the very bottom and they are marked with red font. Filters are enabled for convenient browsing of the change categories.

2. Detailed change information showing the current and previous values of parameter attributes. That information is provide in the following columns:

- in issue ... which shows the value in the previous issue of the document. - in release ... which shows value in the latest issue of the document in the previous product release.

The columns are grouped into attribute-specific sections for structured and convenient view. Use unfold (+) and fold (-) butt in the top bar to browse the attribute-specific change details. Use unfold all (2) and fold all (1) buttons on the left hand side the top bar to respectively show and hide the change details for the whole report.

Note that for all parameters except new and removed ones, the field values for previous issue and previous release are alw provided to show total history information. Additionally, the changed attributes of parameters are highlighted with grey color Highlights are enabled to specify whether there is a change between issues or releases.

Note that for all parameters except new and removed ones, the field values for previous issue and previous release are alw provided to show total history information. Additionally, the changed attributes of parameters are highlighted with grey color Highlights are enabled to specify whether there is a change between issues or releases.

cations, and default values. The

f parameter attributes including

grouped into respective class o browse the tree.

unfold (+) buttons on the left panel

ther location in the structure (for ns:

ment. ent in the previous product

t.

es. That information is provided

ent. the previous product release.

Use unfold (+) and fold (-) buttons buttons on the left hand side of

e and previous release are always are highlighted with grey color.

e and previous release are always are highlighted with grey color.

Managed Object Class Tree

MRBTS ANTL BBMOD POWERGROUP BBPOOL BTSSCL LCELL CAPCFG LNBTS ANR ANRPRL ANRPRW ANRPRX CADPR CAPLIML CRAN CRGPR CTRLTS LTRACE MTRACE FTM AMGR LUAC BTOOTH CERTH ETHLK IPNO BFD BFDGRP IDNS IEIF IVIF IHCP INTP IPRM IPRT IPRTV6 MCAPP NTPS QOS RTPOL TWAMP IPSECC L2SWI OAMMD OAMMA OAMMEP OAMPRF PMTNL POE PPTT SECPRM SYNC STPG

TAC LTAC TOPB TOPF TOPP UNIT WIFICNF GTPU ISHPR LNADJ LNADJL LNADJG LNADJW LNADJX LNCEL AMLEPR APUCCH CAPR CAREL CDFIM DRX GFIM GNFL IAFIM IFGDPR IFGPR IRFIM LNHOG LNHOH LNHOIF LNHOW LNHOX LNNEIH LNREL LNRELG LNRELW LNRELX MPUCCH NBIOT REDRT SDRX SIB SLMEAS UFFIM XPARAM LNCSG LNHENB LNMCE LNM3 MBSFN LNMME LNSENB MFBIPR MODPR MODIMP MODRED MOPR

MOIMP MORED PMRNL PMQAP PMRPQH PSGRP RIM SCTP SLCOMMPROF SLCOMMRES SLCOMMTX SLCOMMSYNC ULCOMP MHA PMCADM RET RMOD SECADM SFP SMOD GNSSE GNSSI SRCU TEST RFRST RFTHLD SFPRST TRBLCADM

Managed Object Class Name

Note: See the How to Read This Report tab for instructions on the usage of Parameter List Changed

actSelMobPrf MRBTS/LNBTS

Changed

moProfileSele MRBTS/LNBTS ct

Changed

spid

MRBTS/LNBTS/LNCEL

• Basic parameters

Activate selective 0 (false), 1 (true) mobility profiles

Handover Control (Miscellaneous)

• Advanced parameters

Mobility profile selection mode

Handover Control (Intra LTE)

0: plmn 1: spid 3: combined

Subscriber profile 1...256, step 1 ID

Load Control (Idle Mode)

On-line

Mandatory

On-line

Mandatory

On-line

Optional

LNBTS - actIdleLB: LNBTS - actIdleLBCaAware: LNCEL - targetSelMethod: MODPR - moDPrId:

LNBTS - actIdleLB: LNBTS - actIdleLBCaAware: LNCEL - targetSelMethod: MODPR - moDPrId:

LNCEL - mcc: LNCEL - mnc: LNCEL - mncLength: LNCEL - moPrId: LNCEL - spid: LNBTS - moProfileSelect: LNCEL - spidLast: LNCEL - mcc: LNCEL - mnc: LNCEL - mncLength: LNCEL - moPrId: LNCEL - spidLast:

LNCEL - mcc: LNCEL - mnc: LNCEL - mncLength: LNCEL - moPrId: LNCEL - spid: LNBTS - moProfileSelect: LNCEL - spidLast: LNCEL - mcc: LNCEL - mnc: LNCEL - mncLength: LNCEL - moPrId: LNCEL - spidLast:

LNBTS - actIdleLB: LNCEL - targetSelMethod: MODPR - moDPrId: LNCEL - spidLast: LNCEL - mcc: LNCEL - mnc: LNCEL - moPrId: LNCEL - mncLength: LNCEL - spidLast: LNCEL - spid: LNBTS - moProfileSelect: LNCEL - mcc: LNCEL - mnc: LNCEL - moPrId: LNCEL - mncLength:

actSelMobPrf can be set to 'true' only if a default profile MODPR instance exists or is created in parallel with the feature activation. If (actIdleLB is 'true') AND (actSelMobPrf is 'false'), Definitions used in below parameter relationships: then targetSelMethod must be configured in all - PLMN ID: Different PLMN IDs can be configured instances of LNCEL. in moPrMappingList with the combination of the If (actIdleLBCaAware is 'true') AND (actSelMobPrf parameters mcc, mnc and mncLength. PLMN ID is 'false'), then targetSelMethod must be means the combination of the parameters mcc, Definitions in below parameter configured used in all instances of LNCEL.relationships: mnc and mncLength. - PLMN ID: Different PLMN IDs can be configured - SPID range: Several spids and SPID ranges can in moPrMappingList with the combination of the be configured in moPrMappingList with parameters mcc, mnc and mncLength. PLMN ID parameters spid and spidLast. SPID range means means the combination of the parameters mcc, the range from spid to spidLast. If spidLast is not mnc and mncLength. configured, SPID range means the single spid - SPID range: Several SPID ranges can be value. configured in moPrMappingList with parameters spid and spidLast. SPID range means the range If moProfileSelect is set to 'spid', then all the from spid to spidLast. If spidLast is not configured, following conditions must be fulfilled: SPID range means the single spid value. - in the elements of moPrMappingList where moPrId is configured, spid must be configured. spid must be less than spidLast. - SPID ranges must be unique with no overlaps in spidLast can only be configured if spid is all elements of moPrMappingList within LNCEL. configured. If moProfileSelect is set to 'plmn', then all the If moProfileSelect is set to 'spid', then all the following conditions must be fulfilled: following conditions must be fulfilled: - in the elements of moPrMappingList where - in the elements of moPrMappingList where moPrId is configured, PLMN ID must be moPrId is configured, spid must be configured. configured. - SPID ranges must be unique with no overlaps in - PLMN ID must be unique in all elements of all elements of moPrMappingList within LNCEL. moPrMappingList within LNCEL. If moProfileSelect is set to 'combined', then all the If moProfileSelect is set to 'combined', then all the following conditions must be fulfilled: following conditions must be fulfilled: - if configured, the pair of SPID range and PLMN - if configured, the pair of SPID range and PLMN ID must be unique in all elements of ID must be unique in all elements of moPrMappingList within LNCEL (i.e. SPID range moPrMappingList within LNCEL (i.e. SPID range must be unique with no overlaps in all the must be unique with no overlaps in all the elements for the same PLMN ID). elements for the same PLMN ID). - in the elements of moPrMappingList where SPID - in the elements of moPrMappingList where SPID range is not configured, PLMN ID must be unique range is not configured, PLMN ID must be unique in all these elements of moPrMappingList within in all these elements of moPrMappingList within LNCEL. LNCEL. - in the elements of moPrMappingList where - in the elements of moPrMappingList where PLMN ID is not configured, SPID range must be PLMN ID is not configured, SPID range must be unique with no overlaps in all these elements of unique with no overlaps in all these elements of moPrMappingList within LNCEL. moPrMappingList within LNCEL. - in the elements of moPrMappingList where - in the elements of moPrMappingList where moPrId is configured, either spid or PLMN ID or moPrId is configured, either spid or PLMN ID or both must be configured. both must be configured.

actSelMobPrf can be set to 'true' only if a default profile MODPR instance exists or is created in parallel with the feature activation.

actSelMobPrf can be set to 'true' only if a default profile MODPR instance exists or is created in parallel with the feature activation.

If (actIdleLB is 'true') AND (actSelMobPrf is 'false'), Definitions used in below parameter relationships: then targetSelMethod must be configured in all - PLMN ID: Different PLMN IDs can be configured instances of LNCEL. in moPrMappingList with the combination of the If (actIdleLBCaAware is 'true') AND (actSelMobPrf parameters mcc, mnc and mncLength. PLMN ID is 'false'), then targetSelMethod must be means the combination of the parameters mcc, Definitions in below parameter configured used in all instances of LNCEL.relationships: mnc and mncLength. - PLMN ID: Different PLMN IDs can be configured - SPID range: Several spids and SPID ranges can in moPrMappingList with the combination of the be configured in moPrMappingList with parameters mcc, mnc and mncLength. PLMN ID parameters spid and spidLast. SPID range means means the combination of the parameters mcc, the range from spid to spidLast. If spidLast is not mnc and mncLength. configured, SPID range means the single spid - SPID range: Several SPID ranges can be value. configured in moPrMappingList with parameters spid and spidLast. SPID range means the range If moProfileSelect is set to 'spid', then all the from spid to spidLast. If spidLast is not configured, following conditions must be fulfilled: SPID range means the single spid value. - in the elements of moPrMappingList where moPrId is configured, spid must be configured. spid must be less than spidLast. - SPID ranges must be unique with no overlaps in spidLast can only be configured if spid is all elements of moPrMappingList within LNCEL. configured.

If (actIdleLB is 'true') AND (actSelMobPrf is 'false'), Definitions used in below parameter relationships: then targetSelMethod must be configured in all - PLMN ID: Different PLMN IDs can be configured instances of LNCEL. in moPrMappingList with the combination of the parameters mcc, mnc and mncLength. PLMN ID means the combination of the parameters mcc, Definitions used in below parameter relationships: mnc and mncLength. - PLMN ID: Different PLMN IDs can be configured - SPID range: Several spids and SPID ranges can in moPrMappingList with the combination of the be configured in moPrMappingList with parameters mcc, mnc and mncLength. PLMN ID parameters spid and spidLast. SPID range means means the combination of the parameters mcc, the range from spid to spidLast. If spidLast is not mnc and mncLength. configured, SPID range means the single spid - SPID range: Several SPID ranges can be value. configured in moPrMappingList with parameters spid and spidLast. SPID range means the range If moProfileSelect is set to 'spid', then all the from spid to spidLast. If spidLast is not configured, following conditions must be fulfilled: SPID range means the single spid value. - in the elements of moPrMappingList where moPrId is configured, spid must be configured. spid must be less than spidLast. - SPID ranges must be unique with no overlaps in spidLast can only be configured if spid is all elements of moPrMappingList within LNCEL. configured.

If moProfileSelect is set to 'plmn', then all the If moProfileSelect is set to 'spid', then all the following conditions must be fulfilled: following conditions must be fulfilled: - in the elements of moPrMappingList where - in the elements of moPrMappingList where moPrId is configured, PLMN ID must be moPrId is configured, spid must be configured. configured. - SPID ranges must be unique with no overlaps in - PLMN ID must be unique in all elements of all elements of moPrMappingList within LNCEL. moPrMappingList within LNCEL.

If moProfileSelect is set to 'plmn', then all the If moProfileSelect is set to 'spid', then all the following conditions must be fulfilled: following conditions must be fulfilled: - in the elements of moPrMappingList where - in the elements of moPrMappingList where moPrId is configured, PLMN ID must be moPrId is configured, spid must be configured. configured. - SPID ranges must be unique with no overlaps in - PLMN ID must be unique in all elements of all elements of moPrMappingList within LNCEL. moPrMappingList within LNCEL.

If moProfileSelect is set to 'combined', then all the If moProfileSelect is set to 'combined', then all the following conditions must be fulfilled: following conditions must be fulfilled: - if configured, the pair of SPID range and PLMN - if configured, the pair of SPID range and PLMN ID must be unique in all elements of ID must be unique in all elements of moPrMappingList within LNCEL (i.e. SPID range moPrMappingList within LNCEL (i.e. SPID range must be unique with no overlaps in all the must be unique with no overlaps in all the elements for the same PLMN ID). elements for the same PLMN ID). - in the elements of moPrMappingList where SPID - in the elements of moPrMappingList where SPID range is not configured, PLMN ID must be unique range is not configured, PLMN ID must be unique in all these elements of moPrMappingList within in all these elements of moPrMappingList within LNCEL. LNCEL. - in the elements of moPrMappingList where - in the elements of moPrMappingList where PLMN ID is not configured, SPID range must be PLMN ID is not configured, SPID range must be unique with no overlaps in all these elements of unique with no overlaps in all these elements of moPrMappingList within LNCEL. moPrMappingList within LNCEL. - in the elements of moPrMappingList where - in the elements of moPrMappingList where moPrId is configured, either spid or PLMN ID or moPrId is configured, either spid or PLMN ID or both must be configured. both must be configured.

If moProfileSelect is set to 'combined', then all the If moProfileSelect is set to 'combined', then all the following conditions must be fulfilled: following conditions must be fulfilled: - if configured, the pair of SPID range and PLMN - if configured, the pair of SPID range and PLMN ID must be unique in all elements of ID must be unique in all elements of moPrMappingList within LNCEL (i.e. SPID range moPrMappingList within LNCEL (i.e. SPID range must be unique with no overlaps in all the must be unique with no overlaps in all the elements for the same PLMN ID). elements for the same PLMN ID). - in the elements of moPrMappingList where SPID - in the elements of moPrMappingList where SPID range is not configured, PLMN ID must be unique range is not configured, PLMN ID must be unique in all these elements of moPrMappingList within in all these elements of moPrMappingList within LNCEL. LNCEL. - in the elements of moPrMappingList where - in the elements of moPrMappingList where PLMN ID is not configured, SPID range must be PLMN ID is not configured, SPID range must be unique with no overlaps in all these elements of unique with no overlaps in all these elements of moPrMappingList within LNCEL. moPrMappingList within LNCEL. - in the elements of moPrMappingList where - in the elements of moPrMappingList where moPrId is configured, either spid or PLMN ID or moPrId is configured, either spid or PLMN ID or both must be configured. both must be configured.

• LTE490 SPID selective mobility profiles (Optional) • LTE487 Idle mode mobility load balancing (Standard) • LTE1905 PLMN ID and SPID selected mobility profiles (Standard) • LTE486 PLMN ID selected mobility profiles • LTE2166 CRL8334 Support of dedicated idle mode (Standard) mobility priorities (Standard) • LTE1905 PLMN ID and SPID selected mobility • LTE2601 CA aware idle mode load balancing profiles (Standard) (Standard)

• LTE490 SPID selective mobility profiles (Optional) • LTE487 Idle mode mobility load balancing (Standard) • LTE1905 PLMN ID and SPID selected mobility profiles (Standard) • LTE486 PLMN ID selected mobility profiles • LTE2166 CRL8334 Support of dedicated idle mode (Standard) mobility priorities (Standard) • LTE1905 PLMN ID and SPID selected mobility • LTE2601 CA aware idle mode load balancing profiles (Standard) (Standard)

• LTE490 SPID selective mobility profiles (Optional) • LTE487 Idle mode mobility load balancing (Standard) • LTE1905 PLMN ID and SPID selected mobility profiles (Standard) • LTE486 PLMN ID selected mobility profiles • LTE2166 CRL8334 Support of dedicated idle mode (Standard) mobility priorities (Standard) • LTE1905 PLMN ID and SPID selected mobility profiles (Standard)

• LTE BTS EM • LTE BTS RAC • RAC RACApp • LTE BTS EM • LTE BTS RAC • RAC RACApp • LTE BTS EM • LTE BTS RAC • RAC RACApp

• LTE BTS EM • LTE BTS RAC • RAC RACApp • LTE BTS EM • LTE BTS RAC • RAC RACApp • LTE BTS EM • LTE BTS RAC • RAC RACApp

• EM LTE BTS • LTE BTS RAC • RAC RACApp • EM LTE BTS • LTE BTS RAC • RAC RACApp • EM LTE BTS • LTE BTS RAC • RAC RACApp