Download Expedient Homemade Firearms Vol II PA Luty...
0
Expedient Homemade Firearms Volume II The .32/.380 Machine Pistol Including The 9mm Machine Pistol
A M anual For Independent Gunsmiths P. A. Luty
Expedient Homemade Firearms: The Machine Pistol By P. A. Luty (D.F.C) Copyright C.2004 by P. A. Luty A Home-Gunsmith Publication All rights reserved. Anyone attempting to reproduce any part of this publication in any form without the express written permission of the author will be tried, sentenced and shot, (and not necessarily in that order) Printed in England by Bunker Books Inc; Direct all enquiries to: www.thehomegunsmith.com
Neither the author nor publisher assumes any responsibility for the use or misuse of the information contained in this book. For academic study purposes only.
‘Gun control’ has had a long history:“The people of the various provinces are strictly forbidden to have in their possession any swords, bows, spears, firearms, or other type of arms. The possession of these elements makes difficult the collection of taxes and dues and tends to permit uprising, therefore, the heads of the provinces, official agents, and deputies are ordered to collect all weapons mentioned above and turn them over to the government.” Toyotomi Hideyshi, Shogun, August 29, 1558
CONTENTS Foreword Introduction Tools Required Buying materials Tubing and materials required Specifications
1 2 4 5 6 7
CHAPTERS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14.
Lower Receiver Construction Grip and Magazine Well Magazine Construction Trigger and Guard Sear Construction Upper Receiver Barrel Assembly Breech Block Assembly The Ejector Mainspring, Guide and Recoil Shield Assembling the Machine Pistol Making a Sling Final Finishing Test Firing
APPENDIX A APPENDIX B APPENDIX C APPENDIX D APPENDIX E APPENDIX F
: : : : : :
Machine Pistol Tube Sizes Tube Sizes for Improvised Barrels Chamber Reamer Suppliers Homemade Reamer .380 Conversion Machinist Drawings
9 15 21 31 33 41 49 53 59 61 67 71 73 75
77 79 81 83 87 89
FOREWORD So, you would like to know how a homemade firearm is constructed, what types of materials are used, and what tools are required to build the gun? I don’t blame you. It is an interesting subject, but more importantly, a useful knowledge to have, especially in these days of increasingly oppressive anti - gun laws. Perhaps this is the first book you have read on the subject, or maybe you have purchased other ‘‘Homemade Firearm’’ publications only to be disappointed and bamboozled by pictures of an engineer or professional Gunsmith building a gun using a lathe and milling machine! The gun made by the man who possesses such equipment is still technically a “Homemade Firearm” because it was made in the home environment; however, relatively few people have access to such equipment. For most people the term “Homemade gun” conjures up the image of a crude looking makeshift contraption, held together with sticky tape and glue, more of a danger to its owner than any potential target! The true homemade firearm does not have to fall into either of the above categories. It is perfectly possible to construct a firearm without a degree in engineering, and one which you would not be ashamed of admitting to building. The Expedient Homemade Firearm strikes a happy balance between these two extremes of construction technology. When the term ‘expedient’ is used to describe the construction of a given product, it describes something that can be made with relative speed and using the best materials available in any given time or place. The Expedient Homemade Firearm adheres to both these principles. It is durable, relatively quick to build, does not require the use of special tools and is constructed from the best off-the-shelf materials available. Expedient is, therefore, the key word when discussing the subject of the home built firearm.
INTRODUCTION In this volume of Expedient Homemade Firearms i will endeavour to show how a more compact and lightweight machine pistol can be constructed from readily available off-the-shelf materials. In these days of anti-gun laws, when firearms may have to be hidden away, the more compact and concealable a weapon is the better. The expedient machine pistol is a .32/.380 calibre weapon. The true expedient firearm is built from the position that no outside influences such as machine tools or professional gunsmith’s materials are available. For this reason nearly all major component parts of the weapon, receivers, barrel, breech block and magazine, are constructed from readily available steel tubing, eliminating any need for a lathe. The barrel, for example, is assembled from a length of seamless hydraulic tube reinforced with a series of steel collars and is smooth-bore rather than rifled. While the accuracy available from the smooth-bore barrel is restricted to relatively close ranges, the relative ease and speed of assembling the expedient barrel more than compensates for this necessary compromise. Manufacturing a gun magazine using the conventional methods of folding sheet steel around a form block can be tricky and a time-consuming process. The expedient magazine avoids these problems, as once again it is constructed of tube and only requires a hacksaw, file, and silver solder to assemble it. The magazine is of a single stack design holding 16 rounds. This is less than the capacity of the commercially produced twin stack design, but again, the relative simplicity of manufacture more than compensates for the reduced capacity. Certain parts of the machine pistol, such as the sear, require the use of hardened steel. For this reason, I have incorporated certain off-the-shelf products into the gun design that are as close to the correct steel types requires as possible. This eliminates the acquisition and heat treatment of specialised steels which can pose a problem. I have not included any sights on the machine pistol as they would only be for cosmetic purposes, rather than to make the gun more accurate.
The machine gun is primarily a point and fire weapon. Reliability and simple functionality are the main priorities, especially for a weapon that should be kept as simple as possible. In short, I have included only what is necessary to ensure the gun will function as reliably as can be expected. It should be noted that the life expectancy of any firearm built using the type of materials and techniques illustrated in this book will be less than that of one built from the correct steels and to machine tool tolerances. However, due to the ease with which parts,(such as the breech block and barrel) can be made; it is possible to keep the firearm in permanent working order by having a selection of spare parts available and ready for use. A spare breech block and barrel should be regarded as a necessity.
WARNING THE MATERIAL PRESENTED IN THIS BOOK REPRESENTS THE AUTHORS ATTEMPTS AT DEVELOPING AND BUILDING HOMEMADE FIREARMS AND DOES NOT NECESSARILY CONDON OR ENCOURAGE THE CONSTRUCTION OF FIREARMS BY ANY INDIVIDUAL OR GROUP. THE CONSTRUCTION OF FIREARMS IN MOST JURISDICTIONS IS ILLEGAL. NEITHER THE AUTHOR NOR PUBLISHER ASSUMES ANY RESPONSIBILITY FOR THE USE OR MISUSE OF THE MATERIAL PRESENTED IN THIS PUBLICATION. THE TECHNICAL DATA PRESENTED, PARTICULARLY ON THE USE OF FIREARMS, INEVITABLY REFLECTS THE AUTHORS INDIVIDUAL EXPERIENCES WITH PARTICULAR FIREARMS UNDER SPECIFIC CIRCUMSTANCES WHICH THE READER CANNOT DUPLICATE EXACTLY. THE MATERIAL SHOULD, THEREFORE, BE TREATED AS ACADEMIC STUDY MATERIAL ONLY AND APPROACHED WITH CAUTION. THE COMPLIANCE WITH ANY LAW IS THE SOLE RESPONSIBILITY OF THE INDIVIDUAL READER.
TOOLS REQUIRED 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12.
Electric Drill or Drill Press Drill Bits 1.5 to 9mm diameter Hacksaw Large Files, Round, Half Round and Flat Angle Grinder Bench Grinder Hammer Set square 14.2 mm (9/16) Taper Pin Reamer Taper Cutting Tool Countersink Tool Large Vice
The tools listed above are the minimum required. Obviously the better selection of tools you have at your disposal the easier the firearm will be to construct. A drill press, for example, while not in the hand tool category, will save you a lot of time when drilling holes, etc. It is worth pointing out that a drill press is no more expensive than a good quality electric hand drill and if you are considering buying a new drill, I would strongly recommend a drill press with a minimum 3/8” chuck capacity. If you have access to a lathe, the need to acquire the tubing for the barrel and breech block will be unnecessary. A lathe is not necessary to construct any part of the firearm featured in this book; I merely point it out in the event of such equipment being available to the reader. The time required to build the machine gun will be dependent partly upon the equipment available to the reader and also upon the general ability of the individual concerned. As a general guide, it should be possible for the average individual to build the entire weapon in a week to ten days, once the necessary materials have been acquired. For the individual who has access to a lathe, the manufacturing time can be halved.
BUYING MATERIALS As I mentioned earlier, almost the entire weapon is constructed from steel tubing. The best places to look for the type of tubing we require are tube stockholders, who will usually have in stock all the tube sizes required for any construction. It should be noted that tube suppliers usually have minimum order charges. I would advise ordering all tube sizes required for construction at the same time to take advantage of the minimum order charges. Many suppliers also have a tube cutting service so I would strongly suggest having the lengths of tube cut into three foot lengths for easy of handling and storage, etc. For small quantities of tube, engineering and steel fabrication shops are a good place to look. However, you will not find all the tube sizes required in such places. A list of tube sizes and materials required are supplied overleaf. I have marked the occasional item with a (*) to indicate that several of that particular item should be purchased in case of mistakes during manufacture. For items such as shaft lock collars, mud wing washers, hexagonal keys/wrenches, socket screws etc, look in the Yellow Pages under “Nut and Bolt” and “Engineering Supplies” for a stockist near you. It is very unlikely your local hardware shop will stock the items required, and a trip to the correct supplier will be a necessity. Spring steel strip material and spring wire (piano/music wire) is available from any good model engineering shop. Your local spring manufacturer is also a good source for spring wire material.
TUBE SIZES REQUIRED 1.
30 x 30 x 2mm
Upper Receiver
2.
30 x 30 x 1.6mm
Lower Receiver
3.
14.29 x 3.25mm
Barrel (SMT)*
4.
12.70 x 2.03mm
Breech Block (SMT/SHT/ERW)*
5.
25.40 x 12.70 x 1.6mm
Magazine
6.
12.70 x 0.91mm
Magazine
7.
34.93 x 15.88 x 1.6mm
Magazine Well
8.
40 x 20 x 1.6mm
Grip
9.
50.80 x 1.6mm
Trigger Guard
* Seamless mechanical/Seamless hydraulic/Electric Resistance Welded
MATERIALS REQUIRED 1.
3” x 2” x 1/8” Steel Plate (Trigger)
2.
10mm Hexagon Wrench/Key (Sear)*
3.
½” Shaft Lock Collars x 14
4.
5 and 6mm Shaft Lock Collars x 2
6.
5.5mm dia’ Steel Rod x 24” long (or 7/32”)
7.
19.05 x 5mm Flat Bar x 25” long (or 3/4 x 3/16 )
8.
3mm dia’ Steel Rod x 5 ½”long (or 1/8”)
9.
9.5 x 1.6mm Steel Strip (Sheet) x 6” long (or 3/8”x 1/16”)
10.
19.05 x 9.5mm Flat Bar x 9” long (or 3/4 x 3/8”)
11.
20 Gauge Piano Wire (Music Wire) Purchase several rolls
12.
18 Gauge x 7/16” Spring Steel Strip, 12”long
13.
20 Gauge x ½” Spring Steel Strip, 8” long
14.
6mm dia’ Socket Screws (x 11) 9mm long (or 1/4” x 3/8”)
SPECIFICATIONS Weapon Type
Machine Pistol
Calibre
.32/.380
Capacity
.32 (15) .380 (14)
Overall Length
18 ¾”
Barrel Length
9”
Weight Unloaded
4 lbs 8 oz
Sights
None
Construction Materials
Tube, Collars, Nuts and Bolts
Material Availability
Good
Tools Required
Hand only
“DESIGN AND DEVELOPMENT” I am often asked questions, by readers of my books, about design and development issues. A question I often hear is, “Do your gun designs actually work”? I am even sent “design improvement” drawings occasionally, by well meaning would-be gun designers! The reader should be aware that the weapons shown in this publication do work, in that, they can throw ammunition “down range” at an alarmingly expensive rate! The reader, however, should also be aware that due to personal circumstances, and the fact that building guns is completely illegal, little time was lost in the “design and development” stage. The gun designs can, therefore, be improved upon in areas such as aesthetics, compactness of design and components, and materials used in construction etc. Despite this, I hope I have lead the way in a particular area of gun design, making it easier for other “homemade gun” designers to follow, and perhaps improve upon what I have done!
Expedient Homemade Firearms
1____
Lay the copied template sheet on a flat surface and, using a sharp craft knife, cut out both templates. The three shaded areas on template No1 are also removed as carefully
L O W E R R E C E IV E R
as possible. It is a good idea to use a ruler to guide the knife, to make cutting out as accurate as possible. Both templates are now
We will start building the machine pistol by
glued to the receiver tube, as shown below.
first constructing the lower receiver. This is
Check that the templates are in as exact an
probably the best place to start because the
alignment with the tube as possible, before
lower receiver accepts most of the guns
marking the position of each recess and
working parts i.e. the trigger mechanism and
contour onto the tube. A scribe or other
magazine.
sharply pointed tool is used for this procedure.
The lower receiver is cut out, using a
The six crossed circles indicate the positions
hacksaw, from an 11 1/8” length of 30 x
of the various holes that must be drilled into
30mm 16 gauge box section steel tubing.
the tube, and these positions must be marked
A heavier gauge may be used up to a wall
also. This is accomplished by placing a
thickness of 2mm,
punch, (sharp
but in the interest
nail, etc) in the
of
centre of each
keeping
the
weapon as light as
cross
possible,
the
and
gauge
(1.6mm)
16
mark tapping
the firmly
tube is best. First,
punch with
a
cut the tube to a length of 11¼”, slightly
hammer to transfer the position of each hole
longer than the 11 1/8” length required. Use
through the template and onto the tube.
a ‘set square’ to ensure both ends of the
Before removing the templates, check that
tube are straight, then wash the tube in
each score line is clearly visible; then remove
warm soapy water to ensure it is thoroughly
the templates. With the tubing clearly marked
clean. Various recesses must be cut into the
out we can start to cut out the lower receiver.
tube, and to make this process as quick and
First, the side contours of the receiver must be
simple as possible, I have supplied two scale
shaped, as indicated by the score lines from
templates, (See Figure A). The template
template No2. A hacksaw and a large half
sheet should be traced, or quicker still,
round file is all that is required to achieve this.
photocopied onto an A4 size sheet of paper
The ends of the tube are shaped first, by
or card. Make several copies, just in case a
removing most of the metal with a hacksaw,
slip of the knife occurs during cutting out.
then carefully filing each end to shape.
-9-
Lower Receiver Construction
Photo 2: Side view of upper receiver
Photo 3: Top view of upper receiver
after cutting out.
showing recesses.
The arched section next to the three
possible to remove the unwanted sections
crossed circles (now punch marked) is the
with
trigger guard recess. Make a saw cut at
a
hacksaw
so
a
series
of
interconnecting holes, around 3mm in
each end of the guard recess marks, and
diameter, must be drilled along the inside
saw to the top of the arch, both saw cuts
edge of each score line. Use a good sharp
making a ‘V’ shape. A large half round file,
drill bit for this procedure and it can be
ideally 1½” to 2” across, is now used to
done surprisingly quickly. With the holes
trim the recess to its correct curved shape.
drilled, place a flat ended punch, such as
Remember, you are sawing through a
a short length of rod, on the sections to be
tube, so both sides must be shaped as
removed and hit the punch sharply with a
close to the same dimensions as possible,
hammer. The unwanted metal will break
(Photo 2). Next, we will drill the holes
away and can be removed. The jagged
through the side of the receiver. The three
edges of each recess can now be filed
holes at the rear of the receiver are made
smooth to the score lines left by the
with a 4mm drill, and the single hole near
template, (Photo 3).
the middle of the receiver is drilled to a diameter of 5mm. The four holes will
Three 6.5mm holes are now drilled through
eventually accept the grip retaining pins
the top of the receiver, in the positions
and the trigger and sear pivot bolts.
marked. The hole behind the magazine
Obviously, the holes are drilled through the
well recess is an exception though, as it is
receiver from one side to the other, so try
drilled through both sides of the receiver.
to keep the drill as near to a right angle as
The recesses for the grip and magazine
possible to ensure each side is the same.
well must pass through the receiver from
If a drill press is used, then the accuracy of
top to bottom. We have already cut the
each hole is ensured. The three recesses
upper recesses with the help of template
that
grip,
No1. The position of these two recesses
trigger, sear and magazine well, can now
must now be transferred to the underside
be cut into the top of the receiver to the
of the receiver. The lower grip recess is
dimensions left by template No1. It is not
positioned several millimetres further back
will
eventually
accept
the
-10-
FIGURE ‘A’: LOWER RECEIVER TEMPLATES. 282mm
1.
REMOVE SHADED AREAS. -11-
BEFORE TEMPLATE CAN BE USED IT MUST BE ENLARGED BY 25% USING A PHOTOCOPIER. Note: Following enlargement by 25% the
overall length of the template should be 282mm, as illustrated above. If it is not this measurement the template can be enlarged or reduced as necessary until the correct measurement of 282mm is achieved.
2.
Screw hole
Spring screw access hole
Trigger/Sear recess
-12-
Grip recess
Trigger screw hole
Grip pin holes
Sear screw hole
Magazine well recess
Screw Hole
Expedient Homemade Firearms
exact position of the lower recess; this can now be cut out. The only difference between the two recesses is that the lower recess has a shallow notch (arrowed) filed into one end. This slot should be 12mm wide x 2mm deep and will accept the magazine spring catch in due course, (Photo 5).
Photo 4: Lower grip recess
Finally, remove any sharp burrs and edges from the inside of the receiver caused by the drilling and filing. The outside surfaces should be polished smooth using medium grade sandpaper until all score lines have been removed. The lower receiver is now finished and we can proceed to fit all of the guns internal parts mentioned earlier.
Photo 5: Lower magazine well recess Note shallow notch (arrowed). than its upper counterpart. This is to ensure that the grip, when fitted, is at a slight angle in relation to the receiver. Measure in a distance of 41mm from the rear of the receiver and score a straight line, this mark being the length of the recess, (See Figure B). The recess width is 20mm, just the
same as its upper counterpart.
Remove the unwanted metal using a hacksaw and file to shape, (Photo 4). The lower magazine well recess is now cut into the underside of the receiver in exactly the same position as the upper recess. The easiest way of transferring the position of the upper recess onto the underside of the receiver is to score two vertical lines down the side of the receiver. The bottom of each line indicates the
-13-
Expedient Homemade Firearms
2____
firmly retain the grip in position. The side of
GRIP AND WELL
and drill through into the grip. The sides of
Two 4 x 30mm spring pins are now used to the receiver is already drilled for the pins but the grip is not. Place a 4mm diameter drill bit into each of the receiver grip holes the grip must be drilled separately, do not just drill all the way through the grip from one side to the other or the holes will not line up and the pins will not tap in. Now tap in each pin until they are flush with the side of the receiver, (Photo 6). A grip made from a length of tube in this way is perfectly
adequate,
and
is
solid
and
reasonably comfortable to hold, The ‘magazine well’, which is basically a guide tube for the magazine, can now be made and installed. The ‘well’ is made from a length of 34.93 x 15.88mm 16 gauge rectangular tube. Do not let the rather
Photo 6: The grip pinned in position
complicated looking
measurement fool
you; it is for all practical purposes, nothing
The grip can be fitted first. This part is
more than 35 x 16mm tube. However, when
nothing more elaborate than a length of 40
buying
x 20mm 16 gauge rectangular tube. A
the
measurement
slightly heavier gauge can be used, but
tube,
ask
to
avoid
for
the
exact
complications.
Unlike the lower receiver and grip, the
once again, to keep the weapon as light as
gauge, (thickness of the tube wall) is very
possible, 16 gauge is ideal.
important as the inside dimensions must be
Cut each end of the grip at a slight angle.
correct, and this is governed by the gauge.
Push the grip into the open-ended lower
I have supplied four drawings for the well,
recess and then up and into the upper
‘A’, ‘B’, ‘C’ and ‘D’ (See Figure D). As shown
recess opening. The top of the grip should
in Drawing ‘A’, the well is 114mm in length.
be flush with the top of the receiver and a
First we must cut away a 12mm section
snug friction fit. As with any part, a certain
from the top of the well so that only the front
amount of hand fitting may be required
wall remains, Drawing ‘B’. This will be
before the grip will slide into position.
formed
-15-
later
into the cartridge
feed
Grip And Magazine Well
rear wall, (arrowed). A corresponding hole, (arrowed), is also drilled through the opposite front wall of the well in alignment with the rear hole, (Photo 7). This can be done when making the first hole by simply drilling all the way through the well from one side to the other. All sharp edges from the inside and outside of the magazine well must be removed with a file, so it is completely smooth. The cartridge feed ramp must be formed to the angle shown in Drawing ‘D’. Clamp the well in a vice so the top of the vice jaws are level with the bottom of the ramp. This will ensure that the ramp is easier to form. Place a short section of rod about 4” in length on the top edge of the ramp and firmly tap the rod with a hammer until the ramp is formed to the angle shown in
Photo 7: The magazine well showing
Drawing ‘D’. While this drawing is a
spring catch recess and rear hole.
template, it does not require copying or
ramp, but first, two sections of metal must
cutting out. The magazine well can simply
be cut out and removed from the rear
be laid over the template until the ramp
wall
the
matches the angle shown in the drawing.
measurements shown in Drawing ‘C’. The
Polish the top surface of the ramp and
width of each recess is governed by the
round off the two sharp corners that will be
wall of the tube, so only the length
present on its front edges.
measurements need to be supplied. Saw
the two recesses and hole cut into the rear
out the unwanted metal using a hacksaw
of the magazine well are to allow the
for the lengthways cuts, and then drill a
fitting of the magazine catch spring. The
row of four or five holes along the bottom
spring has two purposes, to take up excess
edge of each recess, to allow the sections
space in the rear of the well and to hold
to be removed. The sides of each recess
the magazine in place.
will be rough and jagged after sawing out
length of 7/16” x 18 gauge spring steel
and must be filed down to the wall of the
strip, similar to the material used to make
well. A 4mm hole is now drilled through the
those steel rulers available in most good
middle of the remaining section of the
hardware stores.
of
the
magazine
well
to
-16-
The purpose of
It is made from a
BEND
REMOVE 12mm
114mm
A.
B.
FIGURE ‘D’, MAGAZINE WELL CONSTRUCTION.
D.
C. REMOVE 39mm
4mm Hole
REMOVE SHADED AREAS
REMOVE 44mm
-17-
MAGAZINE WELL TEMPLATE
A.
B.
The end of the spring is heated with a gas torch to permit one end to be formed into a loop.
143
C. After forming the loop the spring catch should be bent to the shape of the template. The overall length of the spring should be 116mm after bending.
FIGURE ‘E’, MAGAZINE SPRING CATCH
-18-
116
TEMPLATE
Expedient Homemade Firearms
Clamp about an inch or so of the spring in a vice so that most of the springs length is visible. Heat the visible end using a gas torch until about an inch of the spring is glowing a bright red colour. This must be done to make sure it does not break during bending. Hold the spring about half an inch from its end with a pair of pincers and, while keeping the torch flame on the spring, form the loop. Do not quench the spring
but
allow
it
to
cool
slowly.
Next, clamp the entire length of the spring in a vice so that just the loop is visible. Bend
the
loop
back
slightly
until
it
conforms to the shape of Drawing ‘C’. This should be done with the spring cold, it is not necessary to heat the steel again. Remove the spring from the vice and bend the length of the spring into a slight curve,
Photo 8: The magazine spring catch
this can easily be done using finger Spring steel is available in many different
pressure only. The spring catch should now
gauges and widths, from good model
look similar to Template ‘C’; it does not
engineering supply shops; the kind of
have to be a perfect match, but should
place where builders of model steam
be reasonably close, (Photo 8). Measure
engines and the like buy their supplies.
the gap at the end of the loop (arrowed), it
I have supplied three drawings to illustrate
should
the correct sequence of forming the spring
Finally, the magazine catch can be fitted
into its required shape, (See Figure E).
to the magazine well. A 4mm diameter
Drawing ‘A’ shows the length of the spring before
bending
i.e.,
143mm.
measure
about
6mm
across.
hole must be drilled through the spring
Sawing
so it
through spring steel is very difficult due to
well.
its hardness, so it is preferable to cut to
can I
be bolted to the magazine
have
not
supplied
an
exact
measurement for the position of the hole
length using a cutting disc or the corner of
because you may not bend the spring
a grinding wheel on a bench grinder.
exactly as I have. Mark the position of the
The first step is to form one end of the
hole by holding the spring against the rear
spring into a loop, as shown in Drawing ‘B’.
of the magazine well, so a gap of about
This loop is the section of the spring that
6mm exists between the top of the loop
acts as the magazine release catch.
and the bottom of the well (‘A’ - Photo 9).
-19-
Grip And Magazine Well
Make a mark across the spring in line with
should be a tight push fit, or at least be
the hole we drilled earlier in the rear wall
snug enough so it will stay in position of its
of the well. This is the position at which the
own accord. Position the well so that the
hole is to be drilled. Use a 4mm diameter
top front tip of the feed ramp is 9mm
dome head socket screw about 9mm long
above the top of the receiver. The well will
to retain the spring catch in position, Arrow
eventually be retained with silver solder
‘B’. The hole we drilled earlier in the front
but it must remain moveable for now.
wall of the magazine well is to allow a
The spring catch can now be re-attached
hexagon wrench to be inserted into the
to the magazine well. When fitted, the top
well to hold the socket screw in position,
of the spring catch should be about level
so the nut can be tightened, Arrow ‘C’.
with the top of the magazine well. Don’t
The magazine well and spring catch
worry if it is slightly higher or lower though,
assembly is now finished and ready to be
as it will not interfere in any way with the
inserted into the magazine well recess.
functioning of the finished weapon.
Photo 9: The fully assembled magazine
B
well fitted to receiver.
C
A
FITTNG THE WELL The well is pushed into the top of the receiver and down into the lower recess. Before this can be done, the spring catch must be unbolted and removed. The well
-20-
Expedient Homemade Firearms
3____
rectangular (1” x ½”) tube as shown in Drawing ‘B’. This must be done by sawing down both side walls, rather than just sawing off the top of the tube. With the top
MAGAZINE CONSTRUCTION
removed, remove the two jagged edges that will exist on both inside walls due to the sawing procedure. Measure the height of the tube from top to bottom, it should
As I pointed out at the beginning of this
measure 25mm, as shown in Drawing ‘D’.
book, a relatively easy and quick method
Now run a round or half round file back and
of building a magazine is to modify a length
forth along the tubes open side until a bevel
of tubing, rather than manufacture the
is created, as in Drawing ‘E’. The file should
magazine from scratch. Unlike the 9mm
be a few millimetres larger than the width of
magazine shown in volume one which was
the tube. The two halves are now clamped
constructed from a single length of tubing,
together with a pair of hose clips, as in
the dimensions of the .32/.380 cartridge
Drawing ‘C’. The top round section must be
require the use of two different tube sizes.
slightly smaller in width than the rectangular
The main body of the magazine is a 7 ¾”
tube, so it will rest on the bevel, rather than
length of 25.40 x 12.70 x 1.6mm tube, in
just sitting on top of the tube. This is to make
other words, standard 1” x ½” x 16 gauge.
sure that a narrow channel exists on either
The second magazine tube is a 7 ¾” length
side of the upper round section, as shown in
of 12.70 x 0.91 mm (½” x 20 g) round tube,
Drawing ‘G’. If necessary, place the round
(See Appendix ‘E’ for .380 dimensions).
section in a
vice and gently tighten the
Both these tubes should be washed so they
jaws until the tube is squashed slightly and
are
starting
will fit the bevel as required. Tighten the
seven
hose clips just enough to hold the two
drawings, ’A’ to ‘G’ (Page 23) to illustrate
halves together, but no more than that. The
how the magazine body is assembled
inside height of this assembly must now be
(Figure F).The first step is to saw tube ‘A’ (½”
measured
x 20 gauge) in half. It will have to be sawn
available, though a length of wire cut to the
first from one end and then the other, using
correct length can be used. As can be seen
a large hacksaw in order to get through the
in Drawing ‘G’, the inside height should be
length of the tube. Only one half is required,
25.5 to 26mm. This measurement should
the other is discarded. File this section down
exist
along its entire length as evenly as possible
assembly. It will be necessary to do a small
until it is a thickness of 4.5mm, as shown in
amount of adjustment to achieve this
Drawing ‘F’. Remove the top side of the
measurement.
thoroughly
construction.
I
clean
before
have
supplied
-21-
with
along
the
a
vernier
entire
gauge,
length
of
if
the
Magazine Construction
the joint areas. The body of the magazine is now finished and we can begin to cut it to shape. So as to make this a simple procedure; the accompanying template, (See Figure G), should be glued to the magazine body so that the bottom straight end is level with the end of the magazine. Use a scribe and mark the small curved cut out shape onto the top
of the
magazine. Punch the positions of the 14 cartridge viewing holes (optional) and then remove the template. The 14 holes are 3mm in diameter and are drilled through the magazine body from one side to the other. The top curved cut out section is shaped, using a half round file. A recess and slot are now cut into the back wall of the magazine. The top recess is
6mm
deep
and
as
wide
as
the
Photo 10: The magazine, form block
magazine side walls will allow. The lower
and pin.
slot is cut using a hacksaw blade and is positioned about 2mm above the bottom
With any adjustments made and the two
edge of the magazine. This slot should be
halves clamped together, apply flux to the
around 1.5mm deep and again, as wide
entire length of both joints and silver solder
as the side walls will permit. The base plate
the two sections together. Use a propane
retaining spring will fit into this slot in due
gas torch and heat several inches of the
course.
magazine along one side. Apply the solder and allow it to flow along the
A considerable amount of burring will exist
channel created by the bevel. Carry out
inside the magazine due to the filing and
this procedure at the other end of the
drilling.
magazine, then turn the magazine around
removed with a flat file so that the inside
and apply the solder to the opposite joint.
walls are completely smooth.
Allow to cool and then remove any excess
All the necessary recesses and holes have
solder from the inside and outside of the
now been made and we can proceed to
magazine. Polish the outside walls with
form the magazine ‘lips’. The magazine
sandpaper, paying particular attention to
lips are responsible for holding the stack of
-22-
This
should
be
completely
Expedient Homemade Firearms
6mm
7 ¾”
REAR
MAGAZINE TEMPLATE
FIGURE ‘G’.
1.5mm
-24-
Expedient Homemade Firearms
must be shaped to the correct contour as shown in the accompanying template, (See Figure H). There is no need to copy or cut out the template, it should be used as a guide over which the block is laid. Secure a large file, flat side facing up, in a vice. Hold the form block bar away from you against the file. Draw the bar towards you while at the same time lifting it, maintaining
a
constant
firm
pressure.
This method will shape the end of the block
FIGURE H.
correctly,
and
is
a
foolproof
procedure. Turn the block over and do the
The form block must be filed to the
same to the other side. At intervals during
shape of the above drawing
filing, check the block against the drawing and make sure it is as close as possible to the template contour. Slide the block inside the magazine and position it so the curved end is about 1mm below the top of the lips. Drill through the top most viewing hole and all the way through the block, using the same diameter drill as used for the holes. Tap in a spring pin ¾” in length to securely hold the form block inside the magazine body, (Photo 11). Clamp this assembly in a vice so the jaws are holding it firmly just under the spring
Photo 11: rear view of magazine with
pin position. Place a short length of rod,
form block pinned in place
about 6mm in diameter, against the top of the lips and firmly tap it with a hammer.
cartridges inside the magazine and must
Move the rod back and forth along the
be formed to the correct contour to ensure smooth
feeding
of
cartridges
length of each lip until they are formed to
from
the contours of the block. Now measure
magazine to chamber. For this reason, a
the distance between the lips, it should be
simple ‘form block’ must be made, around
7.5mm,
which the lips are formed.
(See
Appendix
‘E’
for
.380
dimensions). If the gap is less than this
The block is an 8” length of 9.5 x 19.05mm
slide the block back inside the magazine
(3/8” x 3/4” ) flat bar. One end of the block
and gently tap the bottom of the block
-25-
Magazine Construction
effectively driving it upwards, and thus
A small amount of filing to the sides and
increasing the distance between the lips.
front round tip of the follower may be
Polish the inside top edges of each lip with
necessary before it will slide inside the
a small piece of sandpaper to remove any
magazine. Either way, it should be a loose
sharp edges.
sliding fit, so it will run perfectly smoothly back and forth inside the magazine tube.
We are now ready to make and fit the
SPRING MANDREL
internal parts of the magazine. These consist of the ‘follower’, ‘mainspring’, ‘base plate’ and ‘retaining spring’. The follower is made and fitted first. This is nothing more than a piece of 9.5mm (3/8``) x 16 gauge steel strip, cut to a length of 59 mm. Measure in a distance of 35mm from one end and score a straight line. Clamp the
Photo 12: Spring mandrel.
strip in a vice so the top of the jaws are level with the score line. Using a hammer, bend the follower to the contour of Figure
Now we can coil the mainspring, but before
‘I’. Round the front tip of the follower
we can do this, a simple mandrel must be
before bending, and also, file a taper onto
made around which to coil it. For this, three
the followers lower leg in the position
steel rods are required, 6mm in diameter
shown.
and 14`` in length. Each rod should be washed so it is thoroughly clean, then clamped in a vice, each on top of the other with the rod ends level. Using a gas torch, heat the end of the rods and braze them together for a length of about an inch, (Photo 12). Carry out this same procedure to the opposite end of the assembly and then allow it to cool. Drill a small 1.0 to 1.5mm hole through the rod assembly close to one end, through which to feed the spring steel wire. We require 20 gauge wire from which to make the spring. Music or piano wire, as it is commonly called, is usually sold in rolls of 25 foot lengths, and is widely available from most good model engineering shops and
FIGURE I.
spring manufacturers. Do not use any wire
-26-
Expedient Homemade Firearms
other than 20 gauge, or the spring will be too heavy or too light. A six foot length of wire is enough for coiling the spring. Insert the end of the wire through the mandrel hole and knot it to prevent the wire from pulling out. Stand on the wire and pull up on the mandrel until the wire is taut. Alternatively, tie the end of the wire to a stationary object such as a vice, door handle, etc. Hold the mandrel at an angle with both hands and start to turn it to coil the spring. With the spring coiled along the length of the mandrel a gap of around 10mm should exist between each coil of wire. When coiling the spring, the gap can be adjusted by simply increasing or decreasing
the
angle
at
which
the
mandrel is held, (See Figure J). Releasing tension on the wire will allow the spring to partially unwind, the spring becoming triangular in shape. Snip through the knot of wire and slide the spring from the mandrel. The spring must now be bent back into its original rectangular shape. Use your fingers only for this operation and squeeze the sides of each coil back into their correct shape. This is an obvious and straightforward
procedure
and
it
FIGURE J.
will
become self-explanatory about how to do this on seeing the spring, though difficult to
bend along its length when finished, as this
explain in words.
will
When we coil any
not
interfere
with
the
correct
spring, whether round or rectangular, it will
functioning of the magazine. The spring
always uncoil when tension is released.
must now be compressed several times
The round spring will still remain round, but
before it is trimmed to the correct length.
the rectangular version, unfortunately, will
The easiest way to do this is to slide a
always need bending back to shape.
couple of 6mm diameter rods, the same
Don’t worry if the spring has a significant
length as the mandrel, through the spring.
-27-
Magazine Construction
These
act
compressing
as the
a
guide spring
a
and
make
lot
easier.
The magazine spring will shrink in length from 14” to about 10”. Now use a pair of pliers and cut the spring to a length of 8”. The mainspring is now finished and ready to slide inside the magazine. Before the
FIGURE L.
spring is inserted, one end must be fitted with the base plate to seal off the bottom
Clamp the rod in a vice in a vertical
of the magazine. The base plate is made
position so that 4” to 5” of the rod is visible
from the same 9.5mm 16 gauge steel strip
above the vice jaws. Position the middle
as used to make the follower. Cut a 25mm
section of the wire against the rod and
length of the steel and round off one end
bend the wire into a ‘U’ shape, (See Figure
so it is a good fit inside the bottom of the
L). Clamp the open end of this spring in a
magazine. Drill a 4mm diameter hole
vice so the curved end is visible above the
through the middle of the plate so it can
jaws. Tap this protruding section with a
be bolted to the spring. Bend the last coil
hammer until it is bent flat across the top of
of the spring into a loop and use a 4mm
the jaws. The tip of each of the two spring
diameter socket screw, nut and washer, to
‘forks’ must now be bent outwards for a
bolt the base plate to the spring, (See
length of 2mm. It is best to clamp the tips
Figure K).
of each fork in a vice and bend them to shape using a hammer and punch. If the two bent sections are longer than the 2 mm required, they should be reduced using a grinder.
FIGURE K. The base plate retaining spring can now be made. A length of the 20 gauge spring wire, 60mm long, is required from which to form the spring. A length of steel rod 6mm in diameter and about 6” in length is also
FIGURE M.
required around which to form the spring.
-28-
Expedient Homemade Firearms
followed by the mainspring and base plate assembly, and then refit the retaining spring, to hold all the parts in place.
MAGAZINE STOP The magazine is now fully assembled except for the ‘stop’. This is nothing more elaborate than a thin slice of the 15.88 x 34.93mm x 16 gauge tube, used to make the magazine well. The stop prevents the magazine from being pushed too far into the weapon, and also, holds the magazine in position by hooking onto the spring catch. One end of the stop is filed to a taper and the other end is removed completely, (See Figure N).
Photo 13: The magazine ready for assembly. The spring must now be inserted into the slot
in
the
bottom
rear
wall
of
the
magazine, so we can mark the position at which to drill the hole that will hold the spring in position,(See Figure M). With the
FIGURE N.
spring fully inserted, mark the bottom edge of the magazine, at the position where the two forks are pointing. Transfer this position
Before the stop is cut from the tubing, the
to the side of the magazine about 2mm up
gap between the bottom of the well and
from the magazines lower edge. Now drill
the top edge of the spring catch must be
a hole at this point 1.0 to 1.5mm in
measured. It should be about 6mm, but it
diameter through the magazine from one
may be slightly more or less, depending
side to the other. When the spring is now
on how the catch loop was formed.
re-inserted, the two forks should snap into
Assuming the gap is 6mm, a 6mm thick
the holes, and prevent the spring from
section of the 15.88 x 34.93mm tube should
falling out. Remove the spring and the
be cut out. Remove one end of the stop
internal parts can be inserted, (Photo 13).
using a hacksaw and round off the ends
Slide the follower into the magazine first,
of the two resulting prongs with a file.
-29-
Magazine Construction
A taper is then filed on the opposite end and polished smooth. The taper allows the catch to slide over the stop, effectively holding
the
magazine
in
position.
The stops top and bottom sides should be filed completely flat by sliding it back and forth across the surface of a file. This is important because the stop must mate perfectly with the bottom edge of the well when the magazine is inserted into the weapon. Slide the stop over the magazine between the 11th and 12th viewing holes, (Photo 14). This is only a rough setting; the stop must remain loose until the entire weapon is built, when it will be soldered permanently in place. Insert the magazine into the well and the
Photo14: The assembled magazine.
catch should slide over the stop and snap into position, holding the magazine firmly in position, (Photo 15). A small amount of filing may be required before the catch will snap into place, and very little free play should exist between the catch and stop. The magazine, when inserted, should be under constant forward pressure from the top of the spring catch and the catch loop
itself. The spring
eliminates
the
excess space in the rear of the well, effectively holding the magazine as close to the feed ramp as possible.
Photo 15: The spring catch holding magazine in place.
-30-
Expedient Homemade Firearms
4____
finger should be sanded smooth, so it is comfortable when pulled. Drill a 4mm diameter hole through the trigger in the punch marked position, as shown in (Photo 16). Insert the trigger into the receiver
THE TRIGGER
through the guard recess and secure it in position with a 4mm socket screw and nut. The trigger should pivot smoothly on the screw without any snagging or binding. The trigger guard is constructed from a section of 50.80mm (2”) diameter, 16 gauge tubing. The tube should be 26mm in length and each end should be filed perfectly flat by sliding the guard back and forth over a flat file. Now secure the guard in a vice, but to prevent the jaws
FIGURE O.
from squashing it, tighten the jaws against the ends of the guard, rather than the sides. Use a hacksaw and remove a section of the guard so as to create a slot to the measurements in Drawing ‘A’. This slot allows the trigger to pass through the trigger guard. Looking at the guard as a clock face, the slot is cut so the cutting
Photo 16: The trigger is cut from a section of steel plate.
edge of the hacksaw blade is pointing to the ‘ten to two'position, as in Drawing ‘B’.
We can now fit the trigger and guard. Both are very simple and straightforward parts to make. We will start with the trigger by cutting out the accompanying template and gluing it to a section of 1/8” thick steel plate, (See Figure O). The plate should measure a minimum of 3” x 2”. Mark around the template and punch mark the crossed circle. Cut out the trigger with a hacksaw and file to shape. The section of the
trigger
that
is
pulled
by
A.
the
-31-
Trigger And Guard
The guard should be a tight push fit in the guard recess, so it will stay in position of its own accord without any soldering; though it is best to solder it in place so it is secure. It will probably be necessary to squeeze the sides of the guard, so as to make it a slight oval shape, before it is possible to press the guard into place, (Photo 17). With the guard fitted, make sure it does not
DRAWING B.
prevent the trigger from moving freely. If it does, increase the width of the slot.
Photo 17: Trigger and guard fitted to receiver
-32-
Expedient Homemade Firearms
shaped using a file and then polished
5____
smooth with sandpaper. The templates are not copied and removed, but rather, the key is laid over them at intervals until the key matches the templates. The side of the key, which we will now refer to as the sear,
THE SEAR
is filed flat in the position illustrated in Drawing ‘B’. It is quicker to use a bench
The sear is the section of the trigger
grinder to remove the bulk of the steel
mechanism
before finishing off using a file.
that
releases
the breech
Only file
block when the trigger is pulled. It is made
away enough steel until the corner edge is
by
diameter
completely flat, and no further. This flat area
hexagonal wrench, also referred to as
allows the front section of the trigger to rest
Hexagonal
widely
positively against the side of the sear. As
hardware
shown in drawing ‘C’, three holes are now
stores. They are made from hardened
drilled through the sear to the diameters
steel, and because of their shape, lend
and positions shown. The larger of these
themselves ideally to the construction of
holes is drilled first. This is the sear pivot bolt
an expedient sear. Keys can vary in
hole, it is 5mm in diameter and positioned
length depending on the manufacturer,
13mm from the end of the sear. The hole
but length does not matter in this case as
can be drilled in the sears present hardened
we only require the keys middle section.
condition or it can be annealed This will
This does, however, make giving any
depend on what type of drill bits are used. It
measurements
necessary
is preferable to drill the holes without
modifications difficult. For this reason I
annealing the steel by using ‘Cobalt’ drill
have supplied four templates to make
bits. These are specially designed for drilling
shaping the key a simple operation, (See
through hard steel and are very useful,
Figure Q). Both ends of the key must be
though
removed until it is the same length as
unavailable, the sear should be heated until
Drawing ‘A’. It is not possible to saw
it is glowing bright red in colour at the areas
through the key with a hacksaw due to
where the holes are to be made. This should
the hardness of the steel, so an angle
be done twice, allowing the steel to cool
grinder, preferably fitted with a slitting
slowly between each heating. It is best to
wheel, must be used. If an angle grinder is
use a propane gas torch for this procedure
absolutely
as it gives far higher temperatures than a
modifying
available
a
‘Keys’. from
10mm These
most
for
are
good
the
unavailable,
one
of
the
quite
expensive.
If
these
are
tungsten coated hacksaw blades can be
torch
used, though they are quite expensive.
Because the sear is octagonal in shape, the
The top curved section of the key is
first hole has to be drilled on a corner edge.
-33-
fitted
with
a
butane
cartridge.
Sear Construction
First, drill a 2mm diameter hole through the sear, 13mm from the end, then re-drill the hole to its final 5mm diameter. The second 2.5mm hole is now drilled to the right of the 5mm hole. The exact position of it is not too important, but roughly speaking, it is about 3mm from the end of the sear.
Photo 19: Top view of sear with both
Again, file a flat area before attempting to
pins fitted.
drill the hole, so the drill does not slide off the corner. Another 2.5mm hole is now drilled through the flattened area, 44mm from the end of the sear. The hole is situated just below the corner edge, as shown in Drawing ‘C’. The finished sear is shown in Drawing ‘D’.
Photo 20: Sear spring, screw and nut.
Finally, tap a 2.5mm diameter spring pin into each 2.5mm hole until an even length of pin is visible at either side of the sear, (Photos 18 and 19). Each pin should be 1” in length. The sear is now ready to be fitted, but before this can be done, we must make the sear spring, (Photo 20). This is made from a length of ½” x 20 gauge spring steel strip. The spring should be 88mm in length. Drill a 6mm diameter hole a distance of 9mm from one end of the spring, then bend it, using your fingers, to roughly the same shape as Figure ‘R’.
FIGURE R.
Photo 18: The sear is a modified key.
-34-
Expedient Homemade Firearms
FIGURE ‘Q’ SEAR CONSTRUCTION
The sear is made by modifying an hexagonal key.
60mm
-35-
Sear Construction
-36-
Expedient Homemade Firearms
Insert the spring through the sear recess and secure it in place with a socket screw washer and nut. The sear is now positioned over the spring and secured in place with a 5mm diameter socket screw. This should be 35mm in length and held in place with a nut. The long front section of the trigger leg should be resting on top of the protruding pin on the flat side of the sear. When the trigger is pulled, the sear should drop down so its top curved end is level with the top of the receiver, (Photo 21). Don’t worry if it is slightly above or below this position, it will still release the breech block perfectly well. The main priority is that the sear does not bind or snag on the sear recess or the trigger. It should move smoothly and be under constant upwards pressure from the spring. The lower receiver is now fully assembled, (See Photo 22), and we can start to build the upper half of the machine pistol.
Photo 21: Top view of assembled receiver.
-37-
Sear Construction
Photo 22: The fully assembled lower receiver.
-38-
Expedient Homemade Firearms
-39-
Expedient Homemade Firearms
6____ U P P E R R E C E IV E R
Photo 24: Drilling through the lower receiver bolt holes.
The upper receiver is constructed from an 11 ½” length of 30 x 30 x 2mm box section tubing. This is exactly the same size used for
With both receivers still clamped together,
the lower receiver, except that the gauge
scribe the letters “EP” onto the right side of
must be heavier, namely, a wall thickness of
the upper receiver. On the opposite (left
2mm. Before we can cut the necessary
side) scribe the letters “EH” and then
recesses
be
remove the hose clips, (See Figure T).
temporarily attached to the top of the lower
Where the two receivers were joined
receiver using a couple of hose clips, (Photo
together, (bottom side), scribe “MW”. It is
23). To do this, the magazine well and grip
necessary to mark each side of the
must be removed. Make sure that the
receiver in this way to ensure the following
breech, (grip end) of both tubes are level,
recesses are cut into the correct sides of
and that each tube is in as near perfect
the receiver. These letter reference marks
alignment as possible. Thoroughly tighten
stand for Ejection Port (EP), Ejector Hole
both clips to keep the tubes in this position.
(EH), and Magazine Well (MW). The lower
Clamp this assembly in a vice, (lower
receiver can now be re-assembled and
receiver facing up) and drill a 6mm hole
put to one side as we will not require it
through the two lower receiver bolt holes
again until the upper receiver is fully
and through into the upper receiver, (Photo
assembled. The recesses can now be cut
24). By drilling through the two receivers in
into the upper receiver, (See Figure U).
this way, we can be sure that they will be in
We will start with Drawing ‘A’, which shows
accurate alignment when the weapon is
the positions of the ejection port and the
finally assembled.
bolt handle slot. Use a set square and
into
the
tube,
it
must
scribe the position of the ejection port onto the right side of the receiver, where we marked “EP” earlier. The port cannot be cut out with a hacksaw, so a series of inter-connecting
holes,
3
or
4mm
diameter, are drilled along the inside of
Photo 23: The receivers are clamped together with two hose clips.
the score line marks. This will allow
-41-
Upper Receiver
the unwanted section of steel to be
importance to you, but I have simply
removed using a short length of rod and a
placed the slot in the exact corner
hammer. The jagged edges around the
position, as a ‘Happy Medium’ so to
inside circumference of the port can now
speak. It is really just down to personal
be filed smooth.
preference
as
to
where
the
slot
is
positioned.
The bolt handle slot is now cut into the top
We can now turn to Drawing ‘B’ and cut
right hand corner of the receiver. It is
the recesses for the magazine well and
positioned 55mm from the breech end of
sear. Use a set square again to keep each
the receiver and is 110mm in length. Mark
scribe mark as square and accurate as
the beginning and end of the slot, then file
possible, then cut out in the position shown
a flat area between the two marks. This flat
using the same methods described above.
area should be just wide enough to allow
Five holes are now drilled through the left
the corner edge to be drilled without the
side of the receiver, as shown in Drawing
drill slipping off the corner. Again, this
‘C’. Scribe a line down the length of the left
recess cannot be cut out with a saw, so
side, as near to the centre as possible.
drill a series of holes, 6mm in diameter,
Make a punch mark 76mm along this line
along the entire length of the flat area. An
(from the front of the receiver) and drill a
angle grinder is now used to cut through
6.5mm diameter hole at this position. This
and widen the slot. This will allow a flat file
hole will later accept the ejector bolt
to enter the slot, which is then used to file it to a width of 6 to 6.5 mm, (Photo 25).
All recesses have now been cut except for the four holes along the bottom of Drawing ‘C’. These holes are 3mm in diameter and will
shortly
accept
the
sling
loops.
However, until the loops are made, only drill two of the holes, to the measurements in Figure ‘U’, Drawing ‘C’. The sling loops are formed from a length of 3mm diameter (or slightly larger) steel rod, as shown in
Photo 25: The upper receiver with all
Figure ‘V’. Cut off two 65mm lengths of rod
recesses cut.
and
file
Ordinary
a
point
mild
steel
onto
each
rod
is
the
sling
end.
perfectly
The slot can be cut in a lower position if
strong
required, but no lower than 20mm from the
Measure in 20mm from each end of the
lower
This lower
rod and form them into a ‘U’ shape by
position of the bolt handle slot is the more
bending them at this point. The inside
aesthetically pleasing one, if looks are of
measurement of the sling loops should be
edge of the receiver.
-42-
enough
for
loops.
Expedient Homemade Firearms
Bolt handle slot
EP
EH
UPPER RECEIVER
EP
LOWER RECEIVER
Rear view of receivers as if aiming weapon. ‘EH’ (Ejector Hole) ‘EP’ (Ejection Port)
FIGURE ‘T’
-43-
55mm
110mm
18mm
A. RIGHT SIDE
42mm EJECTION PORT
49mm
SEAR
11
-44-
106mm
16mm
15
B.
42mm MAGAZINE WELL
Expedient Homemade Firearms
FIGURE U; UPPER RECEIVER RECESS POSITIONS
49mm
C. CENTER LINE (LEFT SIDE)
76mm EJECTOR HOLE
16mm
12mm
Expedient Homemade Firearms
about 28mm, but don’t worry if it slightly more or less, it does not matter too much. Insert one of the pointed legs into one of the loop holes and tap the other leg with a hammer. This will mark the position of the second loop hole position onto the side of the receiver. Now carry out this same procedure for the second loop and
Photo 26: The Sling Loops are silver
then drill the two holes.
soldered in place.
Sling Loop
Push each loop into position so they are protruding about 6mm (¼” ) from the side of the receiver. Each sling loop is now permanently held in position with a small drop of silver solder, or ordinary electrical (Soft) solder, applied at the point where the loop legs pass through the side of the receiver, (Photo 26). The upper receiver tube is now finished and ready to be fitted with the internal working parts. However, before we can fit the barrel, breech block, mainspring and recoil shield, we must install three ‘Shaft Lock
Collars’
inside
the
receiver.
The collars have two purposes, first, they allow the two receivers to be bolted together and, act as retainers for the barrel, bolt and mainspring assembly. Collars have a variety of uses such as retaining gears and pulleys on machine tools and are widely available from bolt and nut suppliers and good hardware stores. A collar is measured by the size of bar or shaft it is to fit, in other words, if a collar is required to fit a 1” diameter bar, we ask for a 1” collar. Our machine pistol requires fifteen ½” collars.
FIGURE V. -45-
Upper Receiver
The outside diameter (OD) of the ½” collar is usually 1”, however, when purchasing, the OD must be measured to make sure they are of the correct diameter. It is well worth pointing out here that you will occasionally
encounter
collars
although being ½” ,are not 1”
which, OD, but
Photo 27: The Collars are reamed out
slightly larger or smaller. This is due to the fact that different manufacturer may make
using a reamer or similar tool.
collars to slightly different specifications.
reamers, they are prohibitively expensive,
Provided the collars are between 25.40mm
and,
- 26mm (1”) they will be a good sliding fit
unnecessary to do so. When buying any
inside the receiver tube.
reamer second-hand, always check that
Also, measure
as
pointed
out
above,
it
is
the length (thickness) of the collars; they
the
should be around 11mm in length. Each
undamaged, if in doubt, ask someone
collar will be fitted with a grub screw,
who knows! Securely clamp a collar in
which, when tightened, holds the collar on
a vice and place the reamer in a suitable
the bar or tube to which it is fitted. These
‘Tap Holder’, or a manual drill could be
screws are not required for the three
used, provided the chuck is large enough
collars we are fitting inside the receiver;
to accept the diameter of reamer.
these
should
be
unscrewed
and
this
sharp
and
close to a right angle to the collar face as
from their present 12.70mm ( ½” ) to an ID for
are
the collar accurately, keep the reamer as
be increased on two of the three collars 14.2mm. The reasons
edges
To make sure the reamer passes through
discarded. The inside diameter, (ID), must
of
cutting
possible. Apply very light forward pressure
will
to the reamer until it passes all the way
become apparent later.
through the centre of the collar, (Photo 27).
A 14.2mm, (9/16”), taper pin reamer is
Exactly the same procedure is carried out
required for this purpose. Both straight and
on the second of the three collars.
tapered reamers are extensively used in
collars are now ready to insert inside the
engineering, and are widely available
receiver. Eleven 6mm diameter dome
second hand. A good source for supply
head socket screws, 6mm long (measured
are second hand tool and machinery
from the underside of the head to the end
dealers, where whole boxes of reamers
of the thread), are required to retain the
may be found. Many bankrupt stock items
collars in position. The socket screws must
in unused condition may also be acquired
have the same thread size, (pitch), as the
at
grub screws, so the
a
fraction
Whatever
you
of do,
the do
new not
buy
price.
The
socket screws will
screw into the collars. A tap must also be
new
-46-
Expedient Homemade Firearms
acquired with the same thread size as the screws. The two 6mm holes we drilled earlier, (when the two receivers were clamped together) allows two of the collars to be bolted inside the receiver. Insert the first modified collar into the receiver, just in front of the ejection port, and line up the collars grub screw hole with the receiver bolt hole. Use a hexagon key and screw in one of the socket screws through the receiver wall and into the collar. Tighten the screw to firmly hold the collar in place. Now insert the second, (unmodified), collar into the breech of the receiver and secure it in position using the same procedure. The third, (modified) collar is inserted to the left of the ejection port. Drill a 6mm hole in this position 5.5 mm from the left side of the port, securing it in place with a socket screw. Make sure that all three screws are thoroughly tight to prevent the collars from moving. The two collars at the front and breech end of the receiver are now drilled on the other three sides, so each collar will accept three more screws. The third collar, to the left of the port, is only drilled on two sides, i.e. the top and left sides. We cannot drill blindly through the receiver walls and hope to locate the centre of each collar. We must, therefore, find the position of each collar before drilling the holes. The easiest way is to use a set square and scribe a line around all three sides of the receiver in line with the centre of each socket screw fitted earlier. Now measure to the centre of each
line
Photo 28: Three collars fitted to the receiver.
and punch a mark. This will
give you the position of the collars on
-47-
Upper Receiver
each side of the receiver. Where the punch marks indicate, drill a 2 to 3mm diameter hole through the other sides of the three collars. Now using the correct diameter of drill for the tap size, i.e. 5mm, re-drill each hole to the correct diameter. Each hole is now tapped, and the other eight socket screws fitted and tightened, (Photo 28). Look through the receiver from end to end and check that the screws cannot be seen in the centre of the collars. If the ends of the screws are visible they must be shortened. With
the
collars
secured
inside
the
receiver, we can proceed to assemble and fit the barrel, breech block and mainspring assembly.
-48-
Expedient Homemade Firearms
7____
to the inside of the upper receiver tube. The barrel tube is a 9” length of 14.29 x 3.25mm
seamless
mechanical
tubing,
(SMT). The ‘SMT’ and ‘SHT’ category of
B A R R EL A SSEM B LY
industrial applications and are of perfectly
Manufacturing a rifled gun barrel would
adequate strength for
require a lathe and rifling machine, and
firearm
obviously, relatively few people own such
reinforce the barrel, but also increase the
equipment. With any firearm that can truly
barrels outside diameter, so allowing the
be described as homemade, we must
barrel to be installed in the upper receiver.
compromise the inherent accuracy of the
Before we fit the collars, the barrel must be
rifled barrel, for the easily constructed
chambered to accept the .32 calibre
smooth-bore version. While the accuracy
cartridge, (See Appendix ‘E’ for the .380
of the handgun or rifle is very important,
calibre).
the firepower of the machine gun means
‘chamber reamer’ will be required, (See
accuracy is of secondary importance.
Appendix’ C’ for supplier list). First, the
Reliably getting as many bullets to the
barrel must be firmly secured in a vice.
target as rapidly as possible is the main
Place the square shank of the reamer in a
consideration. If you do own, or have
suitable tap holder and then slide the
access to a lathe, the obvious method of
reamer into the barrels bore. Proceed to
barrel construction would be to machine it
rotate the reamer in a clockwise direction,
as a solid unit. The bore would require
while applying light forward pressure to the
machining to a diameter of 7.5mm, using
reamer.
a
then
compound’ should also be applied to the
chambered in the usual manner using the
reamers cutting edges, to ensure a smooth
appropriate calibre of chamber reamer.
finish to the inside circumference of the
A .32 calibre bullet will be a good press fit
chamber walls. Remove the reamer at
in a barrel machined to a bore diameter of
intervals during the chambering process
7.5mm. For the .380 round, a drill diameter
and carefully clean out the barrels bore
The
with a wire cleaning brush. When a
expedient barrel is far easier to make. It
cartridge will chamber to a depth where
consists of a two component assembly, i.e.
3mm of the cartridge base protrudes from
a length of high strength seamless tubing,
the barrels breech, the chamber is cut to
reinforced with a series of shaft lock
the correct depth. The reason for this
collars. The collars are of the same size,
protrusion will become apparent later
i.e. ½”, as those we have just bolted
when we begin to assemble the machine
‘long
series’
drill
bit,
and
of 8.7 or 8.8mm should be used.
tubes
-49-
are
used
barrel.
To
A
quiet
The
for
the improvised collars
chamber
small
extensively
the
amount
not
only
barrel,
of
a
‘cutting
Barrel Assembly
chamber mouth bevel and checking the cartridge fit, we can begin to assemble the barrel. The barrel is fitted with six ½” collars, these are the same size as those bolted inside the upper receiver. We already have one barrel collar bolted inside the receiver, to
Photo 29: The base of the cartridge
the right of the ejection port. This is
must protrude 3mm from the barrel
removed from the receiver and placed over the chamber end of the barrel. This
pistols breech block, (See Photo 29).
collar has already been reamed out to an
Following the chambering process, the chamber
mouth
must
ID of 14.2mm (9/16”) and should be a snug
be chamfered,
press fit over the barrel. Five more collars
(bevelled), using either a countersink
must now be reamed out, using the same
cutting tool or a de-burring tool. The
14.2mm taper pin reamer we used earlier
purpose of chamfering the entrance to the chamber is to permit the smooth feeding
in Chapter Six. Slide two collars onto the
of cartridges from magazine to barrel. The
barrel, behind the barrel retaining collar,
chamfer should be cut so it measures
and the other three in front of the retaining
about 1mm to 1.5mm across (arrowed),
collar, (Photo 30). Use a hexagon key and
(See Figure X). Finally, remove any metal
thoroughly tighten the grub screws on
shavings, etc, from the inside of the
each of the five collars. It is important to
chamber and bore, and check that a
put the retaining collar over the barrel the
cartridge will chamber smoothly under its
same way round as it was inside the
own momentum.
receiver. If it is not, it will not be possible to bolt the barrel to the receiver. Insert the assembled barrel into the receiver and bolt it in place with the four socket screws removed earlier, (Photo 31). With the barrel in position, make sure it is secure and does not move or revolve. Very little ‘play’ should exist between the tube and collar assembly. If, after reaming out, the collars
FIGURE X.
will not slide onto the barrel, the barrel
No force should be required to chamber
may be polished with sandpaper until the
the cartridge, and it should slide smoothly
collars
into
well worth pointing out here that if 9/16”
the
chamber.
After
cutting
the
-50-
will
slide
on
smoothly.
It
is
Expedient Homemade Firearms
collars can be located (with an outside
shown, however, that while ½” collars are
diameter of 25.40 or 26 mm) they will slide
readily available, those in non-standard
straight onto the barrel without the need to
fractional sizes are usually harder to
ream them out. If available, seven 9/16”
locate. However, it is well worth asking for
collars will be required, six for the barrel
9/16” collars when purchasing the other
assembly and one to the left of the
materials as they may be available in your
ejection port. Personal experience has
area.
Photo 30: The fully assembled barrel.
Photo 31: The barrel fitted to the receiver.
-51-
Expedient Homemade Firearms
we can achieve accuracy usually only
8____
available to the lathe owner. At one end of the tube a slot is now cut, 32mm in length and slot Y).
trimmed
to
the
correct
Don’t worry if the slot is slightly less
matter too much. If an angle grinder is not
barrel, and similarly, a milling machine is
available, a series of inter-connecting
not required to construct the breech
holes may be drilled to remove most of the
block, or ‘Bolt’, as it is commonly called.
steel before the slot is filed to its correct
The normal method of bolt construction
dimensions. This slot is the ‘Ejector Slot’,
would be to machine it from a solid
into which the ‘Ejector Bolt” will fit in due
section of steel. For most would-be gun
course. We will discuss this simple part in
makers, this method will be out of the
the following chapter.
question. However, if we only include
The ejector slot end of the tube is now
those sections of the bolt that are strictly
‘countersunk’ using a hand drill fitted with
necessary, and ignore those which are
a ‘taper cutting tool’, (do not use a
not, a ‘skeletonized’ bolt can be quickly
countersink cutter as this will cut the wrong
assembled from a length of tubing and
degree of taper), (See Photo 32). The
a series of shaft lock collars, an assembly
purpose of the tapered wall recess, as we
very much like the barrel, in fact.
will now call it, is to make the feeding of
If you do own a lathe, or know someone
cartridges from magazine to chamber a
who does, the bolt can be easily turned as
more reliable process. If the taper cutting
a one piece unit, (See Appendix ‘F’ for assemble
then
than this 3mm measurement, it does not
necessary to own a lathe to make a gun
To
is
dimensions using a needle file, (See Figure
As shown in the previous chapter, it is not
drawings).
wide, using a slitting
wheel mounted in an angle grinder. The
BREECH BLOCK
machinist
3mm
tool is not available to you, the recess may
an
be cut straight walled, using a 9mm drill bit
‘expedient bolt’, a 130mm (5 1/8”) length
for the .32 bolt, and a 9.7 or 9.8mm for the
of 12.70 x 2.03mm (½” x 14 g) SMT/SHT or
.380. It should be noted, however, that if
ERW tube is required. First, the tube is cut to
drills are used to cut the recess it must be
length and each end is filed completely
done
flat. A tube cutter, (available from any
before
the
ejector
slot
store), is an accurate method of ensuring each end of the tube is as flat as possible. Use the cutter to make a shallow ring around the tube, and then file down to the
Photo 32: A taper cutting tool
ring mark. By using this simple method,
-53-
is cut.
Breech Block Assembly
FIGURE Z. Figure AA). Push the rod in until the top end of the rod is 2mm below the end of the tube. The rod is held in place by two steel pins. Drill two 2mm diameter holes through the tube and rod, and tap in two 2mm diameter pins, the pins being ½” in length. The first pin hole is positioned about 2mm above the end of the ejector slot and the second about 10 mm above the first
FIGURE Y.
hole.
The recess accepts the base of the
2mm deep tapered wall recess has been
cartridge, which, you may remember
created, a recess that would normally be
protrudes 3mm from the breech face of
machined into the front face of the bolt.
the barrel, (See Figure Z). The recess is cut
This area of the bolt is subjected to a great
just deep enough to allow the cartridge
deal
base to ‘seat’ to a depth of 2mm, and no
cartridge case, during the firing cycle.
further, (See Appendix ‘E’ for .380 bolt
The two pins alone are not strong enough
dimensions).The ‘firing pin rod’ can now be
to withstand these pressures, so the rod
fitted inside the tube, it is 8.5mm in
must also be silver soldered for extra
diameter and 31 mm long. Cut the rod to
strength. As shown in Figure ‘AA’, the
length, making sure each end is flat, and
solder is applied to the gap between the
insert it into the tubes tapered end,(See
rod and the inside of the tube. Use low
-54-
With the rod pinned in position, a
of
pressure
from
the
recoiling
Expedient Homemade Firearms
melting point silver solder in conjunction with flux and a propane gas torch. The two pins should be tapped out and the rod removed. Thoroughly coat the rod and pins with flux paste, then re-insert them into the bolt tube. Heat the top 1” or so of the rod and tube assembly until it is glowing a light red colour and then apply the solder. It is preferable to allow as much solder as possible to flow between the rod and tube, but do not apply so much that it overflows onto the top of the rod itself. Silver solder will only flow onto, and adhere to, surfaces that have first been treated with flux. Therefore, make sure no flux is present on top of the rod before starting to heat the tube. After soldering, allow the tube to cool, but do not quench it in water. Polish the tube with sandpaper to remove any flux residue and remove any surplus solder with a file. We have already cut the ejector slot but now we must increase its depth by an extra 1.5mm. This can be done by using one of the large power hacksaw blades,
FIGURE AA.
or three standard blades, taped together.
using the shank of a 1.5mm drill bit.
Run the blade back and forth inside the
Drill the hole to a specific depth, say for
slot until the required depth is achieved.
our example, 12mm. The firing pin must
A good place to find used power hacksaw
protrude 1mm from the top of the rod face
blades is your local engineering shop.
and therefore, the firing pin should be
Look through the scrap bins and you
13mm in length. In other words, the pin
should be able to find one or more,
must be 1mm longer than the depth of the
perfectly good enough for this purpose.
hole into which it is being inserted. Use a
The next step is to drill a 1.5mm diameter
grit stone and shape one end of the pin to
hole in the top centre of the firing pin rod
a slight taper. Apply a drop of ‘Loctite’
to a depth of between 10 and 12mm. This
bearing adhesive into the pin hole and
hole accepts the firing pin which is made
insert the firing pin. Now leave the entire
-55-
Breech Block Assembly
assembly until the adhesive sets. Always check, and double check, that the pin is correctly
adjusted
to
the
protrusion
measurement before permanently gluing the pin in position. If the pin is incorrectly set, the weapon will either fail to fire or the pin will snag on the cartridge base as the cartridge
slides
from
magazine
to
chamber. This can cause the weapon to jam or make the firing cycle erratic and unreliable. Seven collars are now placed over the finished tube assembly, as shown in Figure ‘BB’. These are the same size as those used for the barrel, i.e. ½” and will slide straight on without any modifications. However, on one of the collars, drill a 5mm diameter hole directly opposite the grub screw, through the collars side wall. Tap this hole so it will accept a 6mm diameter socket screw around 18mm in
FIGURE BB.
length. Slide all seven collars over the tube from the end opposite the ejector slot, the third collar being that drilled with the extra hole.
Stack
the
collars
so
they
are
completely flush with the end of the tube and then tighten the grub screws. The 6mm socket screw acts as the bolt handle and
can
now
be
screwed
into
the
modified collar, (Photo 33). If we look at the front face of the bolt, directly into the
FIGURE CC.
recess, the ejector slot should point to position and the bolt
hole in the left side of the receiver wall,
handle to ten thirty (Figure CC). The fully
and check that the ejector slot is visible,
assembled bolt can now be inserted into
and, in correct alignment with the hole.
the receiver. Remove the bolt handle and
If
slide the bolt into position. Now screw the
position until alignment is achieved. Now
bolt handle back into the bolt through the
firmly tighten the bolt handle, (Photo 34).
bolt handle slot. Look through the ejector
The gap between the breech face of the
the three
o’clock
-56-
necessary,
adjust
the
bolt
handle
Expedient Homemade Firearms
barrel and the front face of the bolt should now be checked. This measurement is important,
and
generally
speaking,
it
should be possible to insert a piece of thin card between the two surfaces. The gap ensures that the bolt does not slam into the breech face if the weapon is ‘Dry Fired’, i.e. without a cartridge in the chamber. By moving
the
stack
of
collars
forward
slightly, the gap may be increased, or moved backwards for the opposite effect, if necessary.
Photo 33: The fully assembled bolt. Note position of ejector slot in relation to bolt handle.
Photo 34: The Bolt installed in the fully assembled upper receiver.
-57-
Expedient Homemade Firearms
9____ THE EJECTOR
Photo 35: The Ejector Bolt and nut.
The ejector is the part of the automatic firearm that ‘Kicks’ the spent cases out through the ejection port during the firing cycle. With very few exceptions, the ejector usually consists of a simple blade that
connects
with
the
base
of
the Although the ejector is very simple, its correct length is essential, (See Photo 35)
cartridge as the recoiling case drives the bolt rearwards; thus flicking the case out of
FIGURE DD
the firearm through the ejection port. We will make the ejector from a 6mm diameter socket screw ½” in length. The end of the screw is filed into a 2mm thick blade for a length of about 5mm. One edge of the blade is then filed to a taper, so the opposite edge is made into a point as a result, (See Figure ‘DD’). The ejector is now inserted into the ejector hole and retained in position with a nut. Before the nut is tightened, the ejector must be positioned so the pointed side of the ejector is facing the chamber. Once the ejector is in position, slide the bolt back and forth several times, checking that it does not bind or snag on the ejector. The tip of the ejector should almost scrape the bottom of the ejector slot, a small amount of hand fitting may be required to achieve this. If the ejector is too long it will bind on the bolt, and if it is too short, will not eject the cases when the weapon is discharged.
-59-
Expedient Homemade Firearms
5.5mm rod and a steel collar. It is perfectly
10___
possible to build the entire machine in under one hour and makes coiling a spring a simple procedure, (See Figure ‘EE’).
MAINSPRING
First, drill a 5.5mm (3/16”) diameter hole ½” from each end of the bar. Then 4 ¾“ from each end scribe a straight line. Clamp the bar in a vice and heat the area of this line using a gas torch until the steel is glowing a red colour. Bend the end of the bar at this position into a right angle and then repeat this same procedure at the opposite end of the bar. The base
Photo 36: The spring coiling machine.
section of the machine is now ready to be The mainspring must be the correct length,
fitted with the mandrel, around which the
strength and diameter. If the spring is too
spring is coiled. This is a 23 ½” length of
strong,
generate
5.5mm steel rod. At one end of the
insufficient pressure to cycle the action,
mandrel drill a 1.0 or 1.5mm hole through
and turns the automatic into a single shot
the rod, 1” from the end. Bend the
firearm. If the spring is too light, it may not
opposite end of the mandrel into two right
absorb as much recoil force as necessary.
angles to form the winding handle. It will
This may result in excessive strain on the
be necessary to insert the mandrel into the
action or even a breech explosion, as the
base and mark the position of the two
bolt opens too soon. As I pointed out in
bends before bending the handle to
volume one, trying to find the correct
shape. By using a gas torch to heat the rod
strength, length and diameter of spring
at the points where the two bends are to
can be difficult. For this reason, coiling our
be made, the handle is easily formed with
own mainspring may be a necessity. This
a pair of pliers. Insert the mandrel into the
is, however, far easier than it may at first
base and secure it in place with a
appear.
steel collar. Turn the handle and the
To coil the spring we require a 14 ft length
mandrel
of the same 20 gauge spring wire used for
The machine is now clamped in a vice
the magazine spring. Before we can coil
and we are ready to coil the mainspring,
the spring, a simple spring coiling machine
(Photo 36). Insert the wire through the
must be built.
The machine consists of
hole
only three parts; a 25” length of 19.05 x
knot
5mm (3/4” 3/16“) flat bar, a 23 ½“ length of
The length of spring wire must be placed
the
cartridge
will
-61-
should
and to
revolve
bend
prevent
the It
from
smoothly.
end
into
pulling
a out.
Expedient Homemade Firearms
-62-
Mainspring, Guide, And Recoil Shield
under constant pressure to coil the spring. The easiest method is to stand on it with both feet, leaving both hands free to guide the wire and turn the handle. Use the left hand to hold the wire at a slight angle while turning the handle. Continue turning until the spring is coiled along the entire length of the mandrel. A gap of 4 mm, or thereabouts, should exist between each coil.
This
gap
can
be
increased
or
decreased during coiling by holding the wire on a greater or lesser angle. The first three or four coils will dictate the angle at which to hold the wire, before coiling the remaining length. The mandrel should bow out slightly during coiling to indicate that sufficient tension is being applied to the wire. Snip through the knotted section and any excess wire and, with the spring still on the mandrel, compress it fully
FIGURE FF.
several times. After the spring has been compressed it will be noticed that the
With
spring has shrunk in length from 16” to
the
mainspring
and
guide
rod
constructed we can build the recoil shield,
about 11”. Remove the mandrel collar and
which is responsible for holding the bolt,
slide the mandrel out of the machine to
guide and spring in position.
release the spring. Now snip the spring to a length of 9 ½’’ using a pair of pliers.
RECOIL SHIELD
The mainspring is now finished and ready
The collar fitted to the breech end of the
to be fitted to the spring guide rod, (See
upper receiver already acts as the recoil
Figure ‘FF’). The guide is a 114mm length of
shield, but must be modified one step
5mm diameter rod. One end is rounded,
further.
(tapered), and the other fitted with a 6mm
A
2”
diameter
‘mud
wing
washer’ must be bolted to the collar
collar. The collar is positioned 7mm from the end of the rod.
as
a
of
the
means
of
receiver.
sealing The
the
breech
washer
should
Slide a 1” diameter rubber tap washer
have a 6 or 7mm
onto the tapered end of the guide and
washers come in many different sizes
push it up until it is touching the collar
and are widely available from bolt
-63-
hole. Mud wing
Expedient Homemade Firearms
.
and nut stockists, and good hardware stores. First, remove the collar from the receiver and temporarily bolt the washer to the collar, as shown in Figure ‘GG’. The collar must be bolted as centrally as possible to the washer. Another washer, any diameter over 1”, is placed at the other side of the collar so the collar is sandwiched between
the
two
washers.
Thoroughly
tighten the nut and bolt and then drill two 3mm diameter holes through the 2” washer and all the way through the collar, (Figure ‘HH’). These two holes must be positioned
FIGURE GG
between the four socket screw holes (these allow the collar to be bolted to the receiver). Accuracy of drilling the collar is very important. If the holes are drilled in the wrong places they will either cut through into the screw holes or pass too close to the inside or outside wall of the collar. The latter making it difficult to tap the holes; which is the next step. Run a tap through each hole and bolt the washer to the collar, as shown in Figure ‘ll’. Now insert the collar and
FIGURE HH
washer assembly into the breech of the receiver and secure it in place with the four socket screws. Use a scribe and mark the inside face of the washer using the walls of the receiver as a guide. Unscrew the bolts and remove the washer and it will be marked with a square, as shown in Figure ‘JJ’. Place the washer in a vice and file each side down to the scribe lines until it is square in shape, as shown in Figure ‘KK’. Lightly remove any sharp corners on the washer
then
securely
bolt
the
square
FIGURE II
washer to the collar, as in Figure ‘LL’.
-64-
Mainspring, Guide And Recoil Shield
Photo 37: The fully assembled recoil shield.
FIGURE JJ.
Photo 38: The recoil shield, mainspring and guide rod. The recoil shield is now finished and can be unbolted from the receiver, to allow the spring and guide to be fitted, (Photo 37).
FIGURE KK
Slide the spring onto the guide rod and then insert this assembly into the recoil shield, (Photo 38). Pull the bolt fully back and hold it in this position. Hold the shield and guide assembly in the palm of the hand and use your fingers to hold the spring in the half compressed position. While holding the bolt back, insert the spring and guide into the hollow middle of the bolt (mainspring recess) until the shield is fully inserted. Let the block slide forward to release the tension on the compressed mainspring, then screw in the four socket screws to retain the recoil shield, spring
FIGURE LL.
and guide rod in position, (Photo 39).
-65-
Expedient Homemade Firearms
Pull the bolt back several times and check that it moves smoothly without binding or snagging on any part of the spring and guide assembly. The upper receiver is now fully assembled (Photo 40)
Photo 39: The recoil shield fitted to receiver.
Photo 40: The fully assembled Upper Receiver.
NOTE: If the bolt mainspring is coiled
spring coiling process, you may find that
around
the spring is slightly tight when inserting it
the
5.5mm
diameter
mandrel
described earlier, the mainspring should
into the bolt.
be a smooth sliding fit through the centre
mainspring
of the bolt. However, due to the inevitable
slightly using an 8.8mm diameter drill bit.
inconsistencies that can creep into the .
-66-
If this is encountered, the recess
can
be
enlarged
Expedient Homemade Firearms
11___
be silver soldered in place. Be careful not to disturb the two settings, then separate the two receivers. Remove the magazine and
A S S E M B L IN G
remove the spring catch from the magazine
The two complete receiver assemblies can
well. Use a propane gas torch in conjunction
now be bolted together and the necessary
with flux and low melting point sliver solder
adjustments made, (Photo 41).
Remove
to retain the well and stop in position. Apply
the two socket screws from the underside
the solder to the underside of the stop so the
of the upper receiver and place the two
solder does not interfere with inserting the
receivers together. The two halves should
magazine back into the weapon. Do not
fit closely together with no gap visible
apply too much solder, only a few drops are
between them. However, it may first be
required
necessary to lower the height of the
Propane gas torches and canisters are
magazine well slightly, so the feed ramp
widely available from most good hardware
does not interfere with the underside of the
stores. The gas canisters may be sometimes
Bolt. Insert the two socket screws and bolt
referred to as ‘propane/butane mix’ and are
the two sections firmly together, (See
ideal for silver soldering because the mix of
Figure ‘MM’). The well and magazine stop
gases give a far higher temperature than a
have not yet been permanently fixed in
standard butane torch. Flux must be applied
place.
correct
to the area where the solder is required to
adjustment, which is not possible until the
run, and then heated until the steel is
weapon is fully assembled. The magazine
glowing a light red colour. While keeping the
lips should touch the underside of the bolt,
torch in position, touch the soldering rod
but should not prevent it from moving
against the hot steel until the solder flows.
smoothly back and forth. If necessary,
After the required amount of solder flows into
push the magazine further into the well
the joint, remove the torch flame and allow
until the lips are in the correct position.
the part to cool slowly. Once the part is cool,
Remember, the stop is loose and will allow
clean off any flux residue and excess solder
the magazine to be moved higher or lower
with a file and then polish using a medium
as necessary. The well must also be
grade sandpaper. The magazine well is
adjusted so that the front tip of the feed
soldered along its top side edge, at the point
ramp touches the underside of the bolt,
where it passed through the upper recess.
but again, must not interfere with the bolts
Re-assemble the magazine and attach the
smooth
catch spring to the well. We can now bolt
This
is
to
movement.
allow
With
their
these
strip it of all internal parts. Now unbolt and
two
to
hold
the
stop
in
the two receivers back together.
adjustments made, the well and stop can
-67-
position.
Assembling The Machine Pistol
-68-
Assembling The Machine Pistol
Photo 41: The upper and lower receivers ready to bolt together.
-69-
Expedient Homemade Firearms
12___
M A K IN G A S L IN G A suitable sling
is
a
very important
accessory on any firearm larger than a handgun, as a means of easily carrying the weapon. Obviously, if a sling is available commercially, buying one is simpler than making one. But, as with the
FIGURE NN.
firearm itself, we will assume that this is not possible and making one is necessary. Let’s face facts, the crackpots in power
11/8” wide and be black or dark green in
these days are banning guns, knives and
colour. Two buckles must now be made to
any other scapegoat objects that they
attach the sling to the weapon. These are
wish. These power crazy nutters might ban
made form a 30 x 25mm section of 2mm
slings and holsters too. They’ll claim it will
thick
stop criminals carrying guns!!
Drawing ‘A’ shows the shaded sections
A perfectly suitable sling can be made
that must be removed. Use a drill to
from a 4 ft length of dog lead, or one of the
remove the two unwanted sections and
longer reins used for horses, cows, etc.
file the two rectangular holes to the
These are readily available from any pet,
dimensions in Drawing ‘B’. Round the four
equestrian or farming supply store and are
corners with a file and polish every edge
made from exactly the same material as a
and surface of the buckle with sandpaper,
purpose-made rifle sling. I prefer canvas,
(Photo 42). This polishing is important
but leather or nylon serves just the same
because any sharp or rough edges could
purpose. The lead or rein should be 1” to
fray or cut through the sling material over
steel
plate,
(See
Figure
‘NN’).
a period of time. Don’t worry if the buckles you make are not exactly the same size as those in the illustration, it is only necessary for the sling to feed into the buckle holes. Now adjust the sling length to suit your own personal requirements.
Photo 42: Sling buckles.
-71-
Expedient Homemade Firearms
Right and left side views of the fully assembled firearm. -72-
Expedient Homemade Firearms
13___
As I pointed out earlier, it is far easier to polish the parts after each part is made, rather than having to finish every section of the weapon at this stage.
FINAL FINISHING
First we will finish the upper and lower receivers. Remove all internal parts from the upper receiver with the exception of
For reasons of picture clarity, the machine
the ejector. Place the receiver in a vertical
pistol, seen through the pages of this book,
position on a steel plate or other fireproof
is shown in its final finished appearance.
surface. Apply the torch flame to the top
The firearm at this stage would still have its
end of the receiver, holding it in this
raw metal appearance, so we will discuss
position until heat rings appear on the
here the expedient method of finishing.
surface of the steel. This should happen in
The hot gun bluing process used in the arms
factory,
or
by
the
around 30 seconds assuming a propane
professional
gas torch is used. Don’t move the flame
gunsmith, has no place in a book like this.
around, but hold it on the same point until
Not only would special chemicals be
the steel is seen to change colour. Now
required, but bluing tanks and heating apparatus also. We have seen how a
move the flame further down the receiver
machine pistol can be constructed at
and, at every 2” interval, repeat the
home from commonly available materials.
process described above. When the entire
It is only right to finish the weapon using
side of the receiver is ‘heat treated’, turn
the simplest home applied method.
the receiver around and carry out the
One of the best looking gun finished I have
same procedure on the other three sides.
found is to ‘colour case harden’ each
The lower receiver is finished in exactly the
component part of the firearm. This can be
same way. Do not remove the grip as it
done using nothing more than a gas torch.
can be left in place, but make sure all
This method is not true case hardening, but
internal moveable parts are removed.
does give a similar and extremely good
The magazine must also be stripped
looking finish. With the exception of the
before
bolt, sear and springs, all parts are finished
finished. The barrel assembly can be
using the following method.
finished as a complete unit without having
All
visible external
body
can
be
to remove the collars, but because of the
sanded to a smooth polished finish using a
heavy gauge of tube and thickness of the
fine grade of sandpaper. The better the
assembly, heating the steel will take
finish is before applying the blow torch, the
longer. Small sections, such as the trigger
better
and guard, are finished in just the same
will
must
magazine
be
the finish
surfaces
the
look afterwards.
-73-
Final Finishing
way as the larger components. Obviously
shaft
the firearm could be finished using one of
often zinc plated, and the zinc will interfere
the cold gun blue finishes available from
with the bluing process. However, the zinc
any gun shop, but the way things are
can be easily removed with a quick soak
going there may not be many gun shops
in Hydrochloric Acid. Leave the items in
left before too long! Besides, the heat
the acid solution until the items stop
treatment method of finishing is more
‘bubbling’. This indicates that all the zinc
durable and, in my opinion, better looking.
has been removed. As a means of
If you do decide to use the cold bluing
preventing the formation of rush, the parts
method, I would advise buying the liquid
can then be soaked in a hot baking soda
version of the product. It should be noted,
solution (soda and hot water) before
however, that the cold gun blue liquid will
proceeding to blue the parts. The barrel
not cover up any deep scratch marks
and bolt assemblies do not need to be
present on the guns external surfaces.
dismantled and can be submerged in the
Whichever method of finishing is used, it
two solutions fully assembled. Whichever
will only look as good as the amount of
process is applied to finish the external
effort you put in beforehand. Note also,
surfaces of the machine gun, the resulting
that many hardware products such as
finish should prove to be a pleasing one.
lock
collars
and
Colour image showing finished firearm.
-74-
washers
are
Expedient Homemade Firearms
14___
may be fired; discharging the magazine. The trigger can be release at any time during the firing cycle and the sear should lock the bolt back in the fully cocked position.
TEST FIRING
Most .32/.380 automatic firearms have a very high cycle rate, and the expedient machine pistol is no exception to this rule.
I know what you are thinking; “WILL IT BLOW
UP”?
The
answer
to
A fully loaded magazine will empty in
this
around two or three seconds, so the rpm is
understandable question is a positive NO,
not to be sneezed at. It is rather expensive
provided the weapon is built using the
on the ammunition front though. Full metal
same materials and construction methods
jacket (FMJ) ammunition must be used for
described in this book. However, with any
the weapon to function reliably. The barrel
homemade firearm, it is only wise to test
length is also important because a length
fire the weapon with single shots before
of less than 9” will not generate sufficient
filling the magazine to maximum capacity
pressure to reliably cycle the bolt, so don’t
and pulling the trigger!! Firing single shots
be too enthusiastic with the hacksaw.
first also makes it easier to see what, if any, adjustments are required. Initially, load
The Expedient Firearm is not intended (or
one round into the magazine and cock
designed) to compete with the factory
the weapon. Point the firearm in a safe
made firearm in either looks or the quality
direction and squeeze the trigger. The
of materials used. It is a compromise
cartridge should fire and the spent case
weapon of last resort; available when most
should
port.
legitimate and conventional firearms have
Repeat this procedure, but this time, load
been legislated away, as in the authors
three cartridges into the magazine and
country of residence. However, for all
squeeze the trigger. The weapon should
intents
fire a rapid burst. Provided no jams are
Machine Pistol is a viable firearm if
experienced, the magazine is loaded to
constructed with a reasonable degree of
maximum capacity and one long burst
care and attention to detail.
be
ejected
through
the
-75-
and
purposes,
the
Expedient
Expedient Homemade Firearms
A’
MACHINE PISTOL TUBE SIZES
The tube sizes shown below are those required to construct the major component parts of the Machine Pistol, i.e. receivers, barrel, magazine and bolt, etc. 1)
tubes are ideal for the construction of the
30 x 30 x 2mm (Upper Receiver)
improvised firearm barrel. Because of the 2)
30 x 30 x 1.6mm (Lower Receiver)
3)
25.40mm x 12.70mm + 12.70 x 0.91
many different tube sizes available in ‘seamless
mechanical’
and
‘seamless
hydraulic’ tubing, it is possible to construct a gun barrel to suit almost any calibre of
mm (1 x½"+½"x20g) (Magazine)
firearm. Where possible, heavy gauge tubing can be used for gun barrels,
4)
14.29mm x 3.25mm SMT (Barrel)
providing the design of the firearm will allow it. However, there is no reason why a
5)
12.70mm
x
2.03mm
(½"x14g)
lighter gauge of tubing cannot be used to construct a gun barrel, but it may be
SMT/SHT/ERW (Bolt)
necessary to reinforce it with a second 6)
tube or a series of steel collars for extra
15.88mm x 34.93mm x 1.6mm ERW
strength. Tube manufacturers rarely give
(Magazine Well) 7)
the bore size of tubing in their catalogues. Instead, only the tubes outside diameter
40mm x 20mm x 1.6mm ERW
and
(Grip)
wall
thickness
are
supplied.
To calculate the bore size, the wall thickness must be multiplied by two, and
8)
50.80mm x 1.6 mm (2" x 16g)
this measurement deducted from the tubes outside diameter. For example, a
(Trigger Guard)
wall thickness of 2.50mm is doubled and
The ERW tubing is very useful for the
becomes 5mm. For a 14 x 2.50mm tube,
construction of receivers and magazines
the calculation would be as follows;-
or as sleeving to reinforce or increase the
Tube diameter 14 mm Wall thickness 5 mm Bore diameter = 9mm
diameter of another tube. It should not be used for gun barrelling, unless nothing else is available, due to its welded seam construction. The SMT and SHT category of
-77-
Expedient Homemade Firearms
B’
IMPROVISED GUN BARRELS
Tube sizes for improvised firearm barrels from .22 rimfire to 12 gauge shotgun. Seamless Mechanical Tube (SMT) and Seamless Hydraulic Tube (SHT). CALIBRE
TUBE SIZE REQUIRED (mm)
.22 Rimfire
9.53
x
2.03
(SMT)
5.47
9.52
x
2.03
(SHT)
5.46
.25 ACP
12.70
x
3.25
(SMT)
6.20
.32 ACP
14.29
x
3.25
(SMT)
7.79
.38/.357
15.88
x
3.25
(SMT/SHT)
9.38
19.05
x
4.88
(SMT)
9.29
14.29
x
2.64
(SMT)
9.01
14.00
x
2.50
(SHT)
9.00
15.00
x
3.00
(SHT)
9.00
20.64
x
4.88
(SMT)
10.88
19.05
x
4.06
(SMT)
10.93
.45 ACP
17.46
x
2.95
(SHT)
11.56
12 Gauge
26.99
x
4.06
(SMT)
18.87
28.58
x
4.06
(SMT)
20.46
28.00
x
4.00
(SHT)
20.00
30.00
x
5.00
(SHT)
20.00
9mm/.380
.44/.410
BORE DIA (mm)
All the tube sizes listed here offer an excellent ‘Bullet to Bore’ fit. All will require chambering with the appropriate calibre of chamber reamer.
-79-
Expedient Homemade Firearms
C’
C H A M B E R R E A M E R S U P P L IE R S
The following list of suppliers ship high quality ‘chamber finish reamers’ worldwide. Prices do vary, but at the time of writing, Chamber reamers start at around $35 (£20) for a .22 rimfire reamer. For the machine gun featured in this book, a reamer in either .32 or .380 auto is required. These retail at around $55. There are numerous chamber reamer suppliers available through the Internet, of which the list below is only a small example:-
USEFUL ADDRESSES: DAVID MANSON PRECISION REAMERS 820 EMBURY ROAD, GRAND BLANC, MI 48439,
{Tel:
810 953 0732
USA.
{Fax: 010 953 0735
Email:
[email protected] www.mansonreamers.com
CLYMER MANUFACTURING CO, 1645 WEST HAMLIN ROAD, ROCHESTER HILLS, MI 48309,
{Tel:
248 853 5555
USA.
{Fax: 248 853 1530
Email:
[email protected] www.clymertools.com
SHAWNIE TOOLS, 840 NW 6TH STREET, SUITE F, GRANTS PASS, OR 97526
{Tel:
USA. E-mail:
[email protected] www.reamerrentals.com
-81-
541 471 9161
Expedient Homemade Firearms
D’
HOMEMADE REAMER
I would strongly recommend the use of a
mm drills. After reaming out the tubes, a
professionally ground reamer to cut the
hole must be drilled to accept a socket
chamber of any barrel. However, if it is
screw
necessary to build your own reamer, the
accompanying drawing. The purpose of
following method can be used. Unlike the
the socket screw is to hold the drills firmly
chamber we cut in volume one, using a
in position. Only one drill, the 8.5mm
taper pin reamer, the straight walled case
(9.5mm
of the .32 and .380 cartridges means that
alteration before the ‘reamer set’ can be
an improvised chamber can be cut using
used to cut the chamber. The point of this
a series of three drill bits. For the .32
drill must be removed, and in so doing,
chamber we require one, 7.8mm drill and
create a flat ended cutting tool. This can
two, 8.5mm, and, for the .380, a 9mm drill
be achieved quite easily by touching the
and two 9.5mm in diameter. Whichever of
end of the drill point against the spinning
the two calibres it may be necessary to cut
wheel of a bench grinder, while at the
a chamber for, the only difference is the
same time, slowly rotating the drill so the
diameter of the drills used, all other
point is evenly removed. It is worth
measurements remain the same. We will
pointing out that if a drill press is available
proceed as if cutting the chamber for the
to you, the point of the drill can be
.32
or
accurately removed by simply putting the
thereabouts, lengths of 14.29mm barrel
drill in the drill chuck and lowering the
tube are required, (See Figure ‘OO’). We
spinning drill onto a grit (Carborundum)
will call these the ‘Reamer Tubes’ from now
stone, however, most of the drill point will
on. The inside diameter (ID) of each of the
still need removing first, using the bench
three tubes must first be reamed out using
grinder, before using the drill press method
the three drill sizes given above, i.e. one
of finishing the end of the drill.
cartridge.
tube is reamed
First,
out
three
to
78mm,
in
the
for
position
the
.380),
shown
in
requires
the
any
a diameter of
7.8mm, and the remaining two tubes to a
The two cutting edges of the flat ended drill
diameter of 8.5mm. As can be seen in the
must now be re-sharpened by carefully
accompanying drawing, reamer tube No1
‘touching’ the back edges of the two
accepts the 7.8mm drill and the No2 and
cutters against the wheel of a bench
No3 tubes the 8.5mm drills. For the .380
grinder. This procedure is similar to re-
chamber the No1 tube accepts the 9mm
sharpening the point of a drill, except for
drill and the No2 and No3 tubes the 9.5
our purposes, the end of the drill is now a
-83-
Expedient Homemade Firearms
FIGURE ‘OO’ REAMER CONSTRUCTION.
-84-
Homemade Reamer
flat ended cutting tool. Place each drill in
After using the last (No3) reamer, place
it’s respective reamer tube and adjust the
the No1 reamer back in the barrel tube
No1 drill until it protrudes 16mm from the
and rotate it several times. This will be
end of the reamer tube,(excluding the drill
necessary to remove any burring present
point). Now adjust the No2 and No3 drills
in the bottom of the chamber, caused by
to
14mm respectively. The
the use of the flat ended No3 reamer tool.
drill measurement is the same for both the
Finally, using a wire barrel cleaning brush,
.32 and .380 calibres. When each drill is
remove any metal shavings etc, from
adjusted
inside the barrel and chamber.
13mm
and
to
the
measurements
given
above, tighten each socket screw to
The chamber is now cut and it should be
prevent the drills from moving during use.
possible to slide a cartridge into the
A flat side must now be ground onto the
chamber.
side of each drill shank so they can be turned
using
a
standard
freely and under its own momentum
‘tap
before coming to a stop. At this point the
wrench/Holder’. Before the reamer set can
base of the cartridge should protrude 3mm
be used a guide tube is required to ensure the chamber is accurately cut.
The cartridge must slide in
from the barrels breech, as we saw earlier
This is
in Chapter Seven.
nothing more elaborate than a 6 ½” to 7”
After checking the cartridge fit and cutting
length of 20.64 x 2.95 mm tubing.
the
Our improvised reamer set is now ready
chamber
mouth
bevel,
we
can
proceed to re-assemble the barrel.
for use. To cut the chamber proceed as follows. Firmly clamp the barrel tube in a
The improvised chamber reamer is not the
vice at roughly a 45 degree angle to the
ideal method of cutting the chamber of a
vice jaws and slide the guide tube over
firearm, but it will suffice if a professionally
the end of the barrel. Now slide the No 1
ground chamber reamer is, for any reason,
reamer drill into the guide tube as shown
unavailable.
in the accompanying Photos, 45 and 46.
however, that the genuine article is so investing
numbered, i.e. one, two and three. Apply
any
available, to the tip of each reamer and each reamer while at the same time amount
gun
operation.
proceed to cut the chamber. Slowly turn small
worth
pointing
out,
in
one.
They
are
relatively
inexpensive and make the chambering of
a small amount of cutting compound, if
a
is
widely available, that it is well worth
Each reamer drill is used in the order it is
applying
It
of forward
pressure until each reamer has cut fully to it’s respective depth. At intervals during the cutting operation, clean out any metal shavings from the inside of the chamber.
-85-
barrel
a
quick
and
easy
Expedient Homemade Firearms
Photo’s 45 and 46: The three piece reamer tool; and above, fitted to the barrel ready to cut the chamber.
Note the flat ended No3 reamer tool; shown third from left.
-86-
Expedient Homemade Firearms
E’
.380 CONVERSION
The machine pistol featured in this book
above tubes are used, the collars will
can also be built around the popular .380
require reaming out using a reamer of 14
auto
or 15mm diameter respectively.
pistol
modifications
cartridge being
with
only
required
to
slight the
MAGAZINE ASSEMBLY
magazine, bolt and barrel. It is only down to individual requirements as to which
The magazine construction for the .380
calibre the firearm is chambered.
cartridge is identical to that for the .32, the
The barrel is constructed using exactly the
only difference being the gauge of tube
same principals described in Chapter
used to construct the magazine and the
Seven. The only difference being the size
distance between the magazine lips. The
of tubing used. A length of 14.29 x 2.64 mm
magazine well, follower, and mainspring
SMT tubing is required to construct the .380
should
barrel. The tube should be 9” or 10” in
We require a length of 1” x ½” tubing for
length and chambered to accept the .380
the .380 magazine with a wall thickness of
cartridge using the appropriate calibre of
either 1.22 or 1.50mm (instead of the
chamber reamer. When chambered, the
1.6mm
base of the cartridge must protrude 3mm
The second tube, the 1/2” (12.70mm x
from the barrels breech. The chamber
0.91mm) remains the same for both calibre
mouth is chamfered in exactly the same
magazines. The slightly thinner gauge used
manner as described for the .32 barrel.
for
The shaft lock collars are then reamed out
magazines inside dimensions and as a
and fitted to the barrel. The .380 barrel is
result, the magazine will accept the .380
now finished and can be fitted to the
cartridge.
receiver.
not
used
the
.380
require
for
any
the
alterations.
.32
magazine
magazine).
increases
the
The magazine lips are formed using the
There are two other tube sizes that may be
same
used for the .380 barrel, in the event of the
magazine, except the lips for the .380 must
14.29 x 2.64mm tubing being unavailable.
be ‘set’ so the distance between them is
These are the 14 x 2.50mm and the 15 x
approximately 9mm. A certain amount of
3.00mm tubes. Both offer a bore size of
hand
exactly .380 (9mm), and either one is a
whatever
perfectly good alternative for the machine
building, to ensure it functions as reliably
pistol barrel. However, if either of the
as possible.
-87-
form
fitting
block
should
calibre
used
be
for
the
expected
magazine
we
.32
for are
.380 Conversion
BOLT ASSEMBLY
TUBE SIZES REQUIRED FOR THE .380 BARREL, BOLT AND MAGAZINE.
Only one alteration is required to the bolt assembly for it to accept and function using the .380 cartridge. This alteration
BARREL 14.29 x 2.64mm SMT (or
being the cartridge recess dimensions
14 x 2.50 / 15 x 3.00)
discussed in chapter eight. Assuming we
BOLT 12.70 x 2.03mm SMT/SHT/ERW
are building a .380 bolt, it is only necessary to increase the cartridge recess diameter (fractionally) using the taper cutting tool,
Magazine 25.40 x 12.70mm (1” x
so as to allow the base of the .380
½” x 1.22mm) (or 1.50mm) and
cartridge to recess (seat) to a depth of
12.70 x 0.91mm (½” x 20gauge) round tube.
2mm, as illustrated in
chapter eight.
It should be noted that this modification can only be carried out during the first stage of bolt assembly, and not after the firing pin rod has been fitted. The firing pin protrusion measurement is the same as for the .32 cartridge, i.e. 1mm from the face of the cartridge recess.2
THE EJECTOR The
ejector
should
not
require
any
alteration to either its length or width. However, a small amount of hand fitting may be required.
2
NOTE: The ‘life span’ of the .380 bolt is inevitably less than that of the .32 bolt. This is due to the reduction in the wall thickness of the .380 cartridge recess caused by the use of the larger diameter .380 cartridge. The .380 bolt will therefore require replacing at more frequent intervals.
-88-
Expedient Homemade Firearms
F’
.32/.380 BOLT DIMENSIONS
The drawings on following pages may be
time being ‘soft’ enough to machine.
used if the bolt is to be machined using a
These
lathe, (See Figure ‘PP’). In the interest of
requirements (and many others) where a
ensuring the bolt is as strong and durable
reasonable degree of shock and wear
as
must
resistance is required. Two pre-hardened
machine it from a suitable steel. We do not
steels I have found suitable (and that seem
want to harden and temper the bolt
to be reasonably easy to locate) are
following machining, due to the inevitable
709M40
‘technicalities’
so.
You will need to purchase such materials
Although hardening would be desirable,
from a ‘special steel stockholder’, so look
for the average hobbyist, it would be an
in
unfeasible proposition. The actual size
Stockholders’ for a supplier in your area.
(diameter) of the bolt would necessitate
Searching the ‘Net’ is also a good idea.
the use of a suitable heat source such as a
Such steel is rather expensive in relation to,
fire brick arrangement or a small furnace
for example, a mild steel, especially if you
in which to heat the component to the
have to have it delivered, but you may be
required
tempering
able to purchase a short length as a
temperatures. Not to mention the ability to
‘sample’ or ‘off-cut’. Always check when
use such techniques and equipment.
purchasing such steel that it is in ‘T
Small parts such as, for example, a sear,
condition’ meaning it is sold in the pre-
trigger or firing pin are quite easily heat
hardened state. Some steel manufacturers
treated
a
also advertise their own brands of ‘special
propane gas torch (available from any
steels’ in the pre-hardened condition, and
hardware store) and bucket of oil or water
if you decide to purchase one of these,
in which to quench the job. The larger
you should ensure the steel is suitable for
component does pose problems for the
your purpose. Generally speaking, it must
average individual.
fall into the high tensile, shock and wear
All is not lost however because steels are
resistance category. The alloy steels I have
available
and
listed are a good example of these
tempered conditions. In other words, the
requirements and are reasonably easy to
steel comes “off the shelf” in a pre-
locate.
hardened condition, while at the same
Machining the bolt is a straight forward
is
reasonably
possible,
involved
hardening
using
in
doing
and
nothing
the
in
we
more
than
pre-hardened
-89-
the
steels
are
(EN19T)
‘Yellow
and
suitable
for
817M40
Pages’
under
our
(EN24T).
‘Steel
Machinist Drawings
turning procedure for the lathe owner. Start
protrude 1mm from recess face when fully
with a section of round bar, at least 26mm
seated (D2).
in diameter, and machine the bolt to the
Figure ‘E’, .380 bolt. All dimensions for the
following dimensions:-
.32 bolt apply equally to the .380 bolt,
Referring to Figure ‘A’, Outside diameters
except for cartridge recess (E1) 9.7mm to
(OD) Bolt overall length (OAL) is 131mm.
10.0mm diameter, and front section (E2),
Front section (A1), turn to an OAL of
13.5 mm ‘OD’.3
53mm and 13mm OD. Turn remaining
Figure ‘F’, Position the bolt handle hole
length (A2) to an OD of 26mm, ideally.
50mm from the rear face of bolt.
Figure ‘B’: Using a 5.5mm diameter drill bit, the mainspring/guide recess (B1) is machined to a depth of 100mm.
The
recess is then re-bored to a depth of 74mm using a 9mm diameter bit.
Cartridge Recess. The cartridge recess (B2) is machined to a diameter of 9mm and a depth of 2mm.
Figure ‘C’: Ejector bolt slot. Machine slot (channel) to 32mm in length and 3mm width (C1). Slot depth is 4mm (C2). The slot may be machined at any point on the bolt radius at this stage.
Figure C3, Bolt handle position (looking into the cartridge recess). Drill bolt handle hole at a 45 degree angle adjacent to the ejector bolt slot to a depth of 6mm.
Tap
hole to accept a 6mm diameter socket screw.
Figure ‘D’, Firing pin hole. Drill to 1.5mm diameter (D1) and 12mm depth (D2). Pin consists of 1.5mm dia’ drill shank 13mm in length. Retain the pin using bearing adhesive or similar product. Pin must
3 Note: a certain amount of ‘hand fitting’ may
be required to ensure the bolt will function reliably.
-90-
Expedient Homemade Firearms
.32 BOLT DIMENSIONS (All measurements in millimetres)
-91-
Expedient Homemade Firearms
.380 BOLT DIMENSIONS (All measurements in millimetres)
-92-
1.
2.
3.
4.
5.
6.
7.
8.
10. 16. -93-
19.
15.
17. 18.
14.
11.
20. 12.
SCHEMATIC DRAWING COMPONENT LIST.
13.
9.
1. SLING LOOP 2. GUIDE ROD 3. MAINSPRING 4. BOLT 5. BOLT HANDLE 6. BOLT STOP 7. EJECTOR 8. BARREL RETAINER 9. BARREL 10. MAGAZINE WELL 11. MAGAZINE 12. MAGAZINE STOP 13. BASE PLATE SPRING 14. SPRING CATCH 15. CATCH BOLT 16. SEAR SPRING 17. SEAR 18. TRIGGER GUARD 19. TRIGGER 20. GRIP
Expedient Homemade Firearms
.32/380 Machine Pistol MKII
Expedient Homemade Firearms
.32/380 Machine Pistol MKII
Expedient Homemade Firearms
The upper and lower receiver assembly
(Measurements in millimetres)
With the upper and lower receiver assembly clamped together with two hose clips, the upper receiver must overlap the lower by 6mm, as shown at ‘A’. The slot for the trigger ‘B’, is positioned 58mm from the rear end of the receiver and is 17mm in length. The slot for the trigger guard, ‘C’, is positioned 51mm from the front of the receiver and is 3mm in length and 12.7mm (1/2”) in width.
Hose Clips
LOWER RECEIVER ASSEMBLY
.32/380 Machine Pistol MKII
The trigger guard, grip, and socket screws are secured in place using silver solder at points ‘a’ ‘b’ ‘c’ and ‘d’. The socket screw ‘d’ allows the sear spring to be attached to the receiver.
Expedient Homemade Firearms
TEMPLATES
FULLY ASSEMBLED LOWER RECEIVER
.32/380 Machine Pistol MKII
Expedient Homemade Firearms
.32/380 Machine Pistol MKII
.32/.380 Machine Pistol Mark II
Expedient Homemade Firearms
This schematic drawing shows the simplicity of the MKII design.
A Home Gunsmith Publication
