Especifcaciones++NISSAN+TERRANO+TD27

Technical data on the vehicle Make Model Year Engine Variant

Nissan Terrano ll 2,7 TD 4WD 1991-1996 TD27T

Date: 03-06-2011 Owner Registration No. VIN 1. Reg. Date Data

Technical item Engine Engine ID code

TD27T

Number of cylinders

R4

Number of valves

8, OHV

Capacity/ (bore/ stroke)

2663 cm³ (96,0/ 92,0)

Compression ratio

21,9 ± 0,2: 1

Max. output kW (din hp)/ rpm

73 (100)/ 4000

Max. torque NM/ rpm

220/ 2200

Engine code location

Left side front on the edge at the cylinder head

Vehicle Identification Number location

Under the right front door on the frame side rail

Vehicle identification plate location

Left side engine bay on the scuttle panel

Valve clearance, inlet (cold/ hot)

0,25 warm

i

Valve clearance, exhaust (cold/ hot)

0,25 warm

i

Valve angle/ seat angle

45° - 45° 30'/ 45°

Piston height over block, mm

Max. 0.368 = Head gasket 1.2 ± 0.05 mm

i

Valve height in cylinder head, mm

Intake ÷ 0.79 - ÷ 1.19 Exhaust ÷ 0.80 - ÷ 1.20

i

Compression pressure, bar

29.4 (Min. 24.5) Max. difference 2.9

Oil pressure/ rpm, bar

Min. 0.78/ idle speed (Min. 2.94/ 3000)

Turbo boost pressure, bar

Max. 0,84 - 0,89

Radiator cap, bar/ thermostat °C

0,78 - 0,98/ 82° C

Clutch freeplay, mm

1.0 - 3.0/ 210 - 215 at pedal

Timing gear:

(Gear wheel drive)

i

i i i

Drive belt

Engine management Diagnostic Diagnostic connector

Left side under dashboard at A - door post

Pump/ pump type

Bosch VG distributor pump Kiki 16700-OF002 16700-OF002

Crank position °/ engine piston, mm

0° ± 1° before TDC/

Pump position, mm

0,38 ± 0,02

i

Adjustment method

Dial micrometer/ Notch

i

Injector opening pressure, new, bar

103,0 - 122,8

Injector opening pressure, used, bar

98,1 - 103,0

Injection order

1 - 3 - 4 - 2 (Cylinder 1 at timing gear)

Injection timing mark location

Belt pulley

i

Electrical system Battery

2 x 12 V/ 65 Ah

Starter motor current (cranking), A

Mitsubishi/ 50 - 75 A/ 3000 - 4000 rpm

Voltage relay, Volt at/ amp.

14,1 - 14,7/

i

Terminal definitions DIN 72 552 Alternator max, A

87 A/ 5000 rpm

Glow plug voltage/ drop resistor

Approx. 0.65 ohm

Wheel alignment Load

Full tank

Toe-in, °

0° 20' ± 05'

Camber°

0° 30' ± 30'

i

Caster°

1° 35' ± 30'

i

KPI/SAI°

12° 37'

Toe-out on turns, inner wheel°

34° 27'

Toe-out on turns, outer wheel°

33° 38'

Data

Technical item Wheel alignment Rear camber°

No factory setting

Rear toe-in °

No factory setting

Tyre size

235/ 75 R 15

Tyre pressure, front/ rear, bar

See sticker left B-doorpost

Free play in suspension parts

Factory data

Track-rod end ball joint, mm

Axial 0 - 0,2/ radial 0

i

i

Tightening torques Tightening, NM

Torque standards

Cylinder head bolts, stage 1, Nm

39 - 44 Nm oiled

Cylinder head bolts, stage 2, Nm

54 - 59 Nm

Cylinder head bolts, stage 3, Nm

+ 90° ± 10°

Cylinder head bolts, stage 4, Nm

(Max. distortion 0.2 mm)

Cylinder head bolts, stage 5, Nm

(No retightening)

Main bearings, Nm

167 - 177 step-by-step

Connection rod bearings, Nm

78 - 83

Flywheel, Nm

147 - 167

Crankshaft pulley/ vibration damp. Nm

294 - 324/

Camshaft pulley/ bearings, Nm

44 - 49/ (Rocker arm assembly 20 - 25 Nm)

Pump pulley/ idle wheel, Nm

59 - 69/

Nozzle retainer/ Nozzle in cylinder head

29 - 49/ 54 - 64

Glow plug

15 - 20

Wheel nuts/ bolts, Nm

118 - 147

Wheel hub, front/ rear, Nm

78 - 98 + loosen bolts + 0.5 - 1.5/

i

i

i

Brakes Front, min. thickness (new)

24,0 mm (26,0 mm)

Rear, min. thickness (new)

255,5 mm (254,0 mm)

Capacities Engine Engine oil/ - incl. filter, litre

6,5/ 7,4 (SAE 10W40)

Manual transmission, litre

3,5 (5 gear) (SAE 80W)

i

Final drive, litre

Front 1.3 (SAE 90) Rear 2.8 (SA E 80W/ 90)

i

Power steering, litre

1,0 (Dexron)

Cooling system, litre

10,0

A/C fluid, type/ gram

R134a/ 750 ± 50

A/C oil, type/ cm³

Nissan Type R PAG/ 200

Environmental parametres Idle speed, rpm

750 ± 50

Max rpm (exhaust test)

5050 ± 100

i

Remarks

n 

n nn

Order No.: Mechanic