Driver Display Volvo Truck

Operating Instructions Display, graphic

T3014418

Contents Introduction ............................................ Display, general ..................................... Location and content of display ........... Display control stalk ............................. Display menus .......................................

1 1 2 3 4

Display symbols ..................................... 7 Alarm, warning and information symbols .................................................. 7 Status symbols ..................................... 10 Other symbols ..................................... 10 Messages ............................................... 11 Messages, general ............................... 11 Acknowledging messages ................... 12 Menus .................................................... 14 ............................................................. 14 MENU 1: Gauges ................................. 18 1. Gauges ............................................. 18 MENU 2: Fuel data ............................. 21 2. Fuel data .......................................... 21 MENU 3: Time/distance ..................... 24 3. Time/distance .................................. 24 MENU 4: Display ................................ 31 4. Display ............................................ 31

MENU 5: Vehicle messages ................ 35 5. Vehicle messages ............................ 35 MENU 6: Reset .................................... 36 6. Reset ................................................ 36 Menus when vehicle stationary .......... 37 MENU 7: P-heater timer .................... 38 7. P-heater timer .................................. 38 MENU 8: Display setting .................... 41 8. Display setting ................................ 41 8.5 Change Password .......................... 47 MENU 9: Vehicle Settings .................. 48 9. Vehicle Settings .............................. 48 MENU 10: Diagnostics ........................ 56 10. Diagnostics .................................... 56 MENU 11: Vehicle data ...................... 66 11. Vehicle data ................................... 66 MENU 12: Data log ............................. 68 12. Data log ......................................... 68 MENU 13: Password ........................... 74 13. Password ....................................... 74 Index ...................................................... 77

Introduction Display, general There are two different types of display. The basic display and the graphic display. The basic display is a segment type display and can only show a limited number of characters. The graphics display is larger and can show a variety of different characters and symbols. There are two versions of the graphic display. A simpler version and a full function display. These instructions describe the full function display. Any functions not supported by the simpler version will be indicated. The display contains numerous main menus and sub-menus with their associated functions. These instructions explain each function, how to operate the display using the control lever and what action the driver is required to take when messages are automatically displayed. The initial chapter describes the most fundamental functions with which all drivers should be familiar. The other chapters describe the functions in more depth. Several of these functions are more useful in the workshop than to the driver. At the end of the instructions, there is an alphabetic index with references to the functions to be read.

1

2

Introduction

Location and content of display

T3014418

The display in the centre of the instrument presents the driver with necessary information. It is controlled using the control stalk on the right-hand side of the steering wheel, which is used so that the driver or the mechanics can retrieve information. Certain information is displayed automatically (e.g. warnings).

The information that is available depends on whether the vehicle is in operation or stationary. Certain functions are password protected and are not shown until the correct password is entered, see “13.1 Enter password” page 75

Introduction

3

Display control stalk Manual communication with the display is achieved using the control stalk on the right-hand side of the steering wheel. The following commands are available: 1

”Esc” is used to return to the previous menu and to cancel a setting /operation.

2

”SELECT” confirms the selected choice of menu or symbol.

3

” ” moves the cursor up and is used to set numbers/characters.

4

”∇” moves the cursor down and is used to set numbers/characters.

1

T3008810

4

Introduction

Display menus The display area The display is made up of three main areas: 1

Menu field. The menus, as well as automatic alarm, warning and information messages are shown here.

2

User selection. The left part shows information selected by the driver using the menu Favourite display. The time is shown in the right-hand section

3

(1) (2) (3)

Status bar. The left hand section shows the present status icons. The odometer is shown in the right hand.

Selecting a menu 1

1

Use ” /∇” to move the cursor to the relevant menu, which is then highlighted. The position of the current menu in the menu structure will then be displayed in the top right-hand corner. 2/6 indicates that there are 6 menus at this level and that the current menu is number 2.

2

Pressing ”SELECT” confirms the choice.

3

Pressing ”ESC” exits the chosen menu. Pressing ”ESC” repeatedly will successively move the cursor ”up” to the main menus.

Gauges

2/6

Fuel data Time/distance Display

98C CC

11:45 AM 7658.8 km

Introduction

5

Changing settings 1

2

3

1

” /∇” increases/decreases set values (e.g. number of hours in adjacent example).

Time/distance

11 : 45 AM

Pressing ”SELECT” confirms your choice and moves on to the next position. ”Esc” moves the highlight to the previous number or selection if there are any, otherwise the setting is cancelled.

Below is a flow chart showing how to set the time and date. It will make it easier to move around in the menus and the result of each button press is clearly seen. Note! This is an example. For more detailed information on setting the time and date, see “3.1 Time and date” page 25

001013

98C CC

11:45 AM 7658.8 km

6

Introduction Time/distance

1/5

Time/distance

11 : 45 05 28 99 AM

98C

11:45 AM

CC

11 : 45 052899 ⇒ ⇐

AM Esc

7658.8 km

CC

7658.8 km ⇐

03 : 4 5

05 28 99

1

∇

1

∇

1

∇

1

∇

1

∇

1

∇

AM #

"

03 : 3 5

Esc 05 28 99

AM #

"

03 : 3 2

Esc 05 28 99

AM #

"

03 : 3 2

Esc 05 28 99

PM #

"

03 : 3 2

Esc 12 07 99

PM #

"

03 : 3 2 PM ⇐

Esc 12 07 98

"

Esc

1

∇

Display symbols Alarm, warning and information symbols Alarms, warnings and information symbols are shown at the top (1) and the centre (2).

(1) (2) (3)

Symbol

Meaning High engine coolant temperature

Symbol

Meaning Compressed air, gearbox

Level, coolant Gearbox oil level Low oil pressure Oil pressure, gearbox Low oil level, engine High temperature, engine oil Pre-heating fault Engine temperature too low for engine brake (VEB) Air filter, clogged Engine shuts down

High temperature, transmission fluid Low brake pressure

Overheating, clutch

Temperature, hydraulic retarder Connected trailer without ABS

7

8

Display symbols

Symbol

Meaning

Symbol

Meaning

Poor braking on trailer

Stop

Uneven braking between tractor and trailer

Voltage warning

Trailer EBS function fault

Battery discharge

Low pressure in the air suspension system

Overheating, instrument

Wheel spin Traction Control temporarily disengaged ESP (electronic stability program) temporarily disengaged Baggage hatch open Cab tilt lock open

Superstructure not in drive position

Air suspension in manual position Air suspension not in drive position Low pressure or flow in the steering servo for hydraulically controlled axle

Airbag

Low level, windscreen washer fluid

Headlight fault Brake lights fault

Direction indicators fault Caution, icy road conditions Fault on the input signal to the fuel gauge Fuel filter, warning

Water in fuel

Display symbols Symbol

Meaning Low fuel level

Symbol

9

Meaning Stability control, active

Recording chart cover open or chart for driver 1 missing (Applies only to certain variants)

10

Display symbols

Status symbols Status symbols are displayed in the field furthest down (3).

(1) (2) (3)

Symbol

Meaning

Symbol

Meaning

Pre-heating active or pre-heating fault

Auxiliary brake position A

Parking heater timer activated

Auxiliary brake position 1

Alarm clock activated

Auxiliary brake position 2

Message active

Auxiliary brake position 3

MI

Odometer, miles

KM

Odometer, kilometres

Auxiliary brake position B

PTO

Power take-off active

CC

Cruise Control active

Other symbols There are various other symbols for the other menus which are not explained here. Refer to the sections on the different menus for explanations of the symbols.

Auxiliary brake in operation

Messages

11

Messages, general There are three types of messages:

• • •

Information Warning Stop

Information, warning and stop messages are displayed automatically with their associated symbols. Above the display are three lamps (for information, warning and stop messages) used to draw the attention of the driver whenever necessary. When a stop message comes on and the engine is running a buzzer is activated as well.

More than one message can be active at the same time. When a message is displayed it can be replaced by a new message provided the new one has a higher priority. I.e. the displayed message always has the highest priority. To receive more detailed information on the information, warning and stop messages that are automatically displayed, see “10.1 Fault Diagnostics” page 57

Information message Important! If this indicator light comes on it means there is a new information message. T3014366

Warning messages Important! When this lamp comes on it means that there is a specified fault that must be checked at the next stop. T3014365

Stop message Warning! When this lamp lights up the vehicle must be stopped and the engine must be switched off immediately. T3014364

12

Messages

Acknowledging messages A fault message is acknowledged by pressing ”Esc” after which the display returns to the same status as before the fault occurred. All types of message can be acknowledged. Acknowledged but inactive messages will be displayed again when the ignition key is turned to start position or they can be read in the menu “5. Vehicle messages” page 35. Information or warning messages: Information and warning messages can be acknowledged using ”Esc”. This warning stays acknowledged until the next time the ignition key is turned to the start position. Exceptions: The message can be displayed again if the fault is cancelled and then becomes active again. Example: If the transmission fluid temperature is too high, a message will be activated automatically. The driver acknowledges this message using ”Esc”. If the temperature then drops to a normal level temporarily and then increases again to an excessive level, the warning will activate again. Stop message: The buzzer and a stop message can be acknowledged using ”Esc”, but become active again 10 seconds after the last acknowledgement. The symbol will remain on the whole time.

Messages

13

Examples of symbols and text The information, warning or stop symbol comes on and the information message is shown on the display (for more information on the fault, see “10.1 Fault Diagnostics” page 57 ) A warning tone will be heard if the engine is running when a stop message is activated. The message contains information on where the fault has occurred:

Non-factory fitted equipment If a coach builder or customer has retrofitted equipment that is connected to the data link, the following symbols may be displayed: MID (Message IDentifier) = control unit

Alarm for factory-fitted equipment when stationary: Stop MID 142 fault

Stop engine fault



98 C CC

98C 11:45 AM

CC

11:45 AM 7658.8 km

7658.8 km

Example of symbol + value Information, warning or stop symbol comes on and another symbol + value is displayed. Example of warning message:

Warning, icy road conditions The FREEZING CONDITIONS message is activated when the outside temperature drops below 2C or increases from a lower temperature to -2C. Press ”Esc” to acknowledge the warning. The warning will be cancelled when the temperature drops below -3C or rises to +3C.

Freezing conditions -2C

98C CC

11:45 AM 7658.8 km

14

Menus

Menus This chapter describes all the display functions. The display has 13 different main menus. Menus 7 – 13 are accessible only when the vehicle is stationary and at speeds below 8 km/h. The menus are locked at higher speeds. Several sub-menus are password protected while the vehicle is stationary. Note! If all the menus are to be shown, the correct password must be given. This applies every time the ignition key is turned to the drive position (if it was more than 60 seconds since the last time the ignition key was in the drive position). See “13.1 Enter password” page 75. A password protected menu is indicated by a shaded box in the menu structure. In order to navigate the menus in these instructions, they are numbered in a hierarchical structure with the first number indicating the current main menu. The second number indicates the first level of submenu, the third number the second level of submenu and so on. Every numbered

menu represents a display screen so that it is easy to keep track of which buttons have been pushed. Each menu is also presented in text so that the users will know exactly where they are situated as follows: ”MENU:” followed by the name of the current main menu and the submenu/submenus. The menus on the display in the vehicle are marked in another way. The numbers at top right indicate the current menu and the number of menus at the same hierarchical level. Ex: Menu 3/7 means: There are seven menus at the same hierarchical level. You are in number 3 of these 7.

Menus 1. Gauges

8. Display setting

1.1 Gear position

8.1 Language

1.2 Outside temperature

8.2 Units

1.3 Temperature, engine oil

8.3 Time/Date

1.4 Temperature, gearbox

8.4 Display Light

1.5 Pressure, primary tank

8.5 Change Password1

1.6 Volt meter/Ammeter

9. Vehicle Settings

2. Fuel data

9.1 Traction Control

2.1 Fuel Consumption

9.2 Fleet Limits1

2.2 Leg fuel

9.3 Ammeter Calib.

2.3 Remaining fuel

9.4 Fleet ID1

3. Time/distance

9.5 Daytime running lights

3.1 Time and date

10. Diagnostics

3.2 Alarm clock

10.1 Fault Diagnostics

3.3 Trip meter

10.2 Cluster Selftest

3.4 Average speed

10.3 Part Number

3.5 Estimated time of arrival

11. Vehicle data

4. Display

11.1 Oil level

4.1 Black Panel

11.2 Load Indicator

4.2 Favourite display

12. Data log

4.3 Backlight

12.1 Vehicle number

4.4 Favourite Display, setting

12.2 Total data

4.5 Night/Day

12.3 Trip data

5. Vehicle messages

12.4 Reset Trip data1

6. Reset

13. Password

6.1 Reset

13.1 Enter password

7. P-heater timer 1

7.1 Programming 7.2 Reset

Password protected menu.

15

16

Menus

Menus available when driving

1 Gauges

1.1 Gear position

1.2 Outside temperature

1.3 Temperature, engine oil

1.4 Temperature, transmission fluid

1.5 Pressure, primary tank

1.6 Volt meter/Ammeter

2 Fuel Data

2.1 Fuel Consumption

2.2 Leg fuel

2.3 Remaining fuel

2.1.1 Reset, fuel consumption

Menus

3 Time/Distance

3.1 Time and date

3.2 Alarm clock

17

3.1.1 Time and date setting

3.2.1 Alarm clock setting 3.2.2 Turn off alarm clock

3.3 Trip meter

3.2.3 Activate alarm clock

3.4 Average speed 3.3.1 Reset trip meter 3.5 Estimated time of arrival

3.4.1 Reset average speed

3.5.1 Setting distance

4 Display

4.1 Black Panel

4.2 Favourite display

4.3 Backlight 4.4 Setting Favourite display 4.5. Night/day 5 Vehicle messages

6 Reset

4.3.1 Setting background lighting

18

MENU 1: Gauges

1. Gauges There are several different gauges in the ”Gauges” menu. The number depends on the equipment level of the vehicle. They can be used to view the current status of the most important functions in the vehicle. It is possible to display up to three gauges at once using the favourite display, see “4.2 Favourite display” page 32

1. Gauges 1.1 Gear position 1.2 Outside temperature 1.3 Temperature, engine oil 1.4 Temperature, gearbox 1.5 Pressure, primary tank 1.6 Volt meter/Ammeter Switch between the alternatives using ” /∇”. Press ”Esc” to return to the main menu.

1

1.1 Gear position This gauge is an optional extra.

Gauges

MENU: Gauge, Gear position

E 1 1

The ”TRANSMISSION” menu provides information about the engaged gear, gear lever position, available gears etc. For further information on ”TRANSMISSION” see separate Operating Instructions for ”I-shift”, ”Geartronic” and ”Powertronic”.

1/7

98C CC

A

∇

5H 11:45 AM 7658.8 km

MENU 1: Gauges

19

1.2 Outside temperature This gauge is an optional extra. MENU: Gauge, Temperature out

Gauges

2/7

15C

The outside temperature is displayed as illustrated.

98C

11:45 AM

CC

7658.8 km

1.3 Temperature, engine oil MENU: Gauge, Temperature engine oil

Gauges

3/7

98C

The temperature of the engine oil is displayed as illustrated.

98C

11:45 AM

CC

7658.8 km

1.4 Temperature, gearbox This gauge is an optional extra. MENU: Gauge, Temperature, gearbox

Gauges

4/7

75C

The temperature of the gearbox oil is displayed as illustrated.

98C CC

11:45 AM 7658.8 km

20

MENU 1: Gauges

1.5 Pressure, primary tank This gauge is an optional extra. MENU: Gauge, Pressure, primary tank

Gauges

If the pressure in the primary tank drops below 9.7 Bar an error message is displayed together with the info/warning symbol.

6/7

9.7 Bar 98C CC

11:45 AM 7658.8 km

1.6 Volt meter/Ammeter This gauge is an optional extra. MENU: Gauge, Volt meter/Ammeter

Gauges

Voltages below 20.0 V are shown as LOW if the engine speed is lower than 800 rpm for 10 minutes. Voltages above 30 V are shown as HIGH. If the ammeter reading should become too low, the ammeter reading will automatically be displayed with the message ”Discharge”.

7/7

24.3 V 98C CC

12 A 11:45 AM 7658.8 km

MENU 2: Fuel data

21

2. Fuel data The ”Fuel Data” menu provides information on the fuel consumption of the vehicle in various situations. It is also possible to see how much fuel has been consumed over a certain distance and how much fuel remains. In addition to this, it is possible to see the range remaining before having to refuel.

2. Fuel data 2.1 Fuel Consumption 2.1.1 Reset fuel consumption 2.3 Leg fuel 2.3.1 Reset, Leg data 2.2 Remaining fuel Switch between the alternatives using ” /∇”. Confirm selection using ”SELECT”. Press ”Esc” to return to the main menu.

1

22

MENU 2: Fuel data

2.1 Fuel Consumption MENU: Fuel Economy, Fuel Consumption For setting units, see “8.2 Units” page 42

Fuel data

The following facts about the fuel consumption are displayed:

1/3

ø 26.0 25.3

#

⊥

98C CC

•

•

Average fuel consumption: The value is presented as a figure and an arrow pointing down. (See illustration: ø26.) The display shows ”— — —” for a short time after the reset while the average fuel consumption is calculated. Instantaneous or actual fuel consumption: The value is presented numerically as well as in the form of a bar. (See illustration: 25.3)

2.1.1 Reset fuel consumption MENU: Fuel Economy, Fuel Consumption To reset all fuel data, press ”SELECT”, and keep ”SELECT” pressed down for 1 second.

•

11:45 AM 7658.8 km

Target fuel consumption: The value is displayed as a T upside down below the bar. For information about how this value is set, see “9.2.3 Fleet Limits: Fuel (target)” page 52

Note! The bar is not displayed while idling and fuel consumption will be displayed in litres/hour (alternatively gallons/hour) instead.

Fuel data

1/1

To reset ALL fuel data? Press for 1 second.

98C CC

11:45 AM 7658.8 km

MENU 2: Fuel data

23

2.2 Leg fuel MENU: Fuel Data, Leg fuel The display shows:

•

Fuel data

2/3

The leg fuel amount (consumption since last reset)

102 L 98C CC

11:45 AM 7658.8 km

2.2.1 Resetting, fuel data MENU: Fuel Data, Leg fuel To reset all fuel data, see “2.1.1 Reset fuel consumption” page 22

2.3 Remaining fuel MENU: Fuel Data, Remaining fuel The display shows:

• •

Fuel data

3/3

Fuel remaining.

265 km 102 L

Estimated range at present average consumption.

98C CC

11:45 AM 7658.8 km

24

MENU 3: Time/distance

3. Time/distance The time and date can be set in the ”Time/distance” menu. There is also an alarm clock that can be set from this menu. Below the menu there is also a trip meter to see the distance driven since the last reset. The average speed since the last reset can also be seen. By specifying the distance to your destination, the vehicle will be able to estimate the time of arrival. Switch between the alternatives using ” /∇”. Confirm selection using ”SELECT”. Press ”Esc” to return to the main menu.

1

Note! The ”Time and date” menu and ”Alarm clock” can be accessed even when the ignition key is in the stop position. Activate the menu by pressing one of the buttons on the control lever for 1 second or longer. The menu will stay active for 30 seconds after the last button was pressed.

3. Time/distance 3.1 Time and date 3.1.1 Time and date setting 3.2 Alarm clock 3.2.1 Alarm clock setting 3.2.2 Turn off alarm clock 3.2.3 Activate alarm clock 3.3 Trip meter 3.3.1 Reset trip meter 3.4 Average speed 3.4.1 Reset average speed 3.5 Estimated time of arrival 3.5.1 Inputting distance to destination

MENU 3: Time/distance

25

3.1 Time and date MENU: Time/Distance, Time and date Time/distance

Shows current time and date. For alternative settings 12h or 24h and date format, see “8.3 Time/Date” page 43.

1/5

11:45 AM 98C

001013 11:45 AM

CC

7658.8 km

3.1.1 Time and date setting For a flowchart of setting the time and date, seeTable page 6. The clock cannot be altered if the vehicle is equipped with a tachograph. This is done instead in the tachograph’s clock setting menu (see ”Driver’s Manual, Tachograph)” 1

To set the time and date, press ”SELECT” when you are in the ”Time/distance” menu and the clock/date function is displayed.

2

Set the hours using ” /∇”. Confirm using ”SELECT”.

3

Set the first number for the minutes using ” /∇” Confirm using ”SELECT”.

4

Set the second number for the minutes using ” /∇”. Confirm using ”SELECT”.

1

1

5

Set AM/PM (if using the 12h clock) using ” /∇”. Confirm using ”SELECT”.

6

Set the two figures furthest to the left in the date using ” /∇”. Confirm using ”SELECT”.

7

Set the two middle figures in the date using ” /∇”. Confirm using ”SELECT”.

8

Set the two figures furthest to the right in the date using ” /∇”. Confirm using ”SELECT”.

9

”Esc” moves the highlight to the previous number or selection if there are any, otherwise the setting is cancelled.

1

1

1

1

1

Ignition key in off position The time/date setting will be cancelled if more than 30 seconds elapse between button presses while the ignition key is in the

stop position. The time/date that was set before cancellation will apply.

26

MENU 3: Time/distance

3.2 Alarm clock MENU: Time/Distance, alarm clock Time/distance

The alarm clock cannot be set while driving but the buzzer alarm can be switched off, see “3.2.2 Turn off alarm clock” page 27.

1/1

00:00 OFF 98C CC

11:45 AM 7658.8 km

3.2.1 Alarm clock, setting 1

To set the alarm clock press ”SELECT” when the ”Alarm clock” menu is displayed in the ”Time/distance” menu.

2

Move the cursor to NEW TIME using ” /∇”. Press ”SELECT”.

5

Set the second number for the minutes using ” /∇”. Confirm using ”SELECT”.

6

Set AM/PM (if using the 12h clock) using ” /∇”. Confirm using ”SELECT”.

7

”ON” is now selected. Press ”SELECT”. The symbol below is shown on the status bar to indicate that the alarm clock is active.

8

”Esc” moves the highlight to the previous number or selection if there are any, otherwise the setting is cancelled.

1

Time/distance

1/1

00:00

ON OFF

1 1

NEW TIME

98C

11:45 AM

CC

7658.8 km

1

3

Set the hours using ” /∇”. Confirm using ”SELECT”.

4

Set the first number for the minutes using ” /∇” Confirm using ”SELECT”.

1

MENU 3: Time/distance

27

3.2.2 Turn off alarm clock When the alarm clock goes off, ALARM will flash, the current time will be displayed and a warning signal will sound. The alarm will turn itself off after 60 seconds or when ”Esc” is pressed.

3.2.3 Activate alarm clock Activating the alarm clock without changing alarm time:

Time/distance

ON

1

1

Use ” /∇” to move the cursor to ”ON”.

2

”SELECT” activates the alarm clock and the symbol will be displayed on the status bar.

07:30

The alarm clock setting will be cancelled if more than 30 seconds elapse between button presses while the ignition key is in the stop position.

OFF NEW TIME

98C CC

Ignition key in off position

1/1

11:45 AM 7658.8 km

28

MENU 3: Time/distance

3.3 Trip meter MENU: Time/Distance, Tripmeter Two separate trip distances can be saved and displayed as illustrated below. Distances for leg 1 and leg 2 are displayed in the window.

Time/distance

3/5

1 2 230.0 33.0

Note! The trip values must be reset before each measurement.

98C

11:45 AM

CC

7658.8 km

3.3.1 Reset trip meter 1 2

Press ”SELECT” in the ”Tripmeter” menu. New menu asking whether to reset the tripmeter. Use ” /∇” to move the cursor between leg 1 and leg 2. Confirm using ”SELECT” or press ”Esc” to discontinue the reset procedure.

1

Time/distance

Press

1/1

Reset? for 1 second. 1

98C CC

2

11:45 AM 7658.8 km

MENU 3: Time/distance

29

3.4 Average speed MENU: Time/Dist, Average Speed The average speed is calculated as the distance driven divided by the time the engine has been running (since latest reset). Two different average speeds can be calculated. Average speed 1 and 2 are displayed in the window. Note! The trip values must be reset before each measurement.

Time/distance

4/5

1 30.0

2 84.0

98C

11:45 AM

CC

7658.8 km

3.4.1 Reset average speed 1 2

Press ”SELECT” when the ”Average speed” menu is displayed. New menu asking whether to reset the average speed. Use ” /∇” to move the cursor between average speeds 1 and 2. Confirm using ”SELECT” or press ”Esc” to discontinue the reset procedure.

1

Time/distance

Press

1/1

Reset? for 1 second. 1

98C CC

2

11:45 AM 7658.8 km

30

MENU 3: Time/distance

3.5 Estimated time of arrival MENU: Time/Distance, Estimated Time of Arrival The estimated time of arrival is calculated as the remaining distance divided by the vehicle’s average speed.

Time/distance

4/5

14:57 387 km

98C CC

11:45 AM 7658.8 km

3.5.1 Inputting distance to destination 1 2

Press ”SELECT” when the ”Estimated time of arrival” menu is displayed.

Time/distance

1/1

Give distance:

New menu with question on distance to destination. Input a distance using ” /∇” and Confirm using ”SELECT” or press ”Esc” to discontinue the reset procedure.

0000

1

98C CC

11:45 AM 7658.8 km

MENU 4: Display

31

4. Display The driver can enter display settings in the ”Display” menu. It is possible to dim the entire display for night driving or adjust the brightness level. The ”Favourite Display” function enables up to three different gauges and functions to be displayed at the same time. Switch between the alternatives using ” /∇”. Confirm selection using ”SELECT”. Press ”Esc” to return to the main menu.

1

4. Display 4.1 Black Panel 4.2 Favourite display 4.3 Backlight 4.4 Favourite Display, setting 4.5 Night/Day

4.1 Black Panel MENU: Info Display, Black Panel Use this function to activate the ”Black Panel” function. When ”Black Panel” is selected the only functions visible are the speedometer, tachometer (without colour field) and the bottom row of the display. The following events will switch the display backlight back on:

• • •

a message is activated a button is pressed the engine speed enters the red sector of the tachometer

Display

1/5

Black Panel Favourite Display Backlighting

98C CC

11:45 AM 7658.8 km

32

MENU 4: Display

4.2 Favourite display MENU: Display, Favourite Display Use this function to activate the ”Favourite Display”. Favourite Display selections are made in the ”Favourite Display, setting” menu.

Display

2/5

Black Panel Favourite Display Backlighting

98C CC

11:45 AM 7658.8 km

4.3 Backlight MENU: Display, Backlight Adjusting the rheostat which controls the instrument lighting levels will also change the brightness setting of the display when the vehicle lighting is switched on. This menu allows the backlight brightness setting to be adjusted in relation to the level of the other instrument lighting.

4.3.1 Backlight setting

Display

3/5

To increase or decrease the backlight setting, press ” ” or ”∇”. Press ”SELECT” to confirm.

1

”Esc” will cancel the setting.

98C CC

11:45 AM 7658.8 km

MENU 4: Display 4.4 Favourite Display, setting MENU: Display, Favourite Display Selections can only be made here when the vehicle is stationary. This function lets the driver choose what is to be shown on the display. Up to three different fields can be displayed at the same time. Each area can contain 12 different gauges and functions. 1 2 3 4 5 6 7 8 9 10 11 12

No display Gear position, see 1.1 Outside temperature, see 1.2 Temperature, engine oil, see 1.3 Temperature, transmission fluid, see 1.4 Voltmeter/Ammeter, see 1.6 Fuel Consumption, see 2.1 Leg fuel, see 2.2 Remaining fuel, see 2.3 Tripmeter, see 3.3 Average speed, see 3.4 Estimated time of arrival, see 3.5

33

34 1

MENU 4: Display To set the favourite display, press ”SELECT” when the ”Favourite Display” menu is highlighted in the ”Display” menu.

75C

CC 2

11:45 AM 7658.8 km

Press ”SELECT” again to activate the top field. Select gauge/function using ” /∇”. Press ”SELECT” when the gauge/function is displayed.

1

7.0 Bar

1 ∇

15C

98C CC

11:45 AM 7658.8 km

4.5 Night/Day MENU: Display, Night/Day This function is used to switch between yellow text on a black background and black text on a yellow background.

Press ”SELECT” once again to activate the next field. Select gauge/function using ” /∇”. Press ”SELECT” when the gauge/function is displayed.

1

4

15C

98C

3

Press ”SELECT” or ”Esc” until all the fields are active and the clock is displayed.

If an error message should appear on the display, it will be shown in the top two areas. Acknowledge the message by pressing ”Esc”. If there are multiple messages, acknowledge them by pressing ”Esc” repeatedly.

MENU 5: Vehicle messages

35

5. Vehicle messages MENU: Vehicle messages

5. Vehicle messages

A symbol on the status bar will indicate that there are acknowledged messages stored. A warning lamp will also come on for each message specifying its priority, see “Messages, general” page 11.

Vehicle messages

1

98C

Display the messages using ” /∇”. Press ”Esc” to return to the main menu.

1/5

CC

11:45 AM 7658.8 km

An acknowledged message that is still active will be displayed as an unacknowledged message the next time the ignition key is turned to drive position. The message symbol will stay on as long as there are messages that have not been dealt with.

If there are no messages The display indicates when there are no messages.

1/1

Vehicle messages

No messages

98C

11:45 AM 7658.8 km

36

MENU 6: Reset

6. Reset This function will reset several functions at the same time.

6.1 Reset MENU: Reset Pressing ”SELECT” and holding down for more than 1 second, will reset the following functions:

• • • •

Fuel consumption Leg fuel Trip meters 1 & 2 Average speeds 1 & 2

6. Reset 6.1 Reset

Menus when vehicle stationary

Menus when vehicle stationary 7. P-heater timer

10.1 Fault Diagnostics

7.1 Programming

10.2 Cluster Selftest

7.2 Reset

10.3 Part Number

8. Display setting

11. Service

8.1 Language

11.1 Oil level

8.2 Units

11.2 Load Indicator

8.3 Time/Date

12. Data log

8.4 Display Light

12.1 Vehicle ID 1

8.5 Change Password

12.2 Total data 12.3 Trip data

9. Vehicle Settings

12.4 Reset trip data1

9.1 Traction Control 9.2 Fleet Limits1

13. Password 13.1 Enter password

9.3 Ammeter Calib. 9.4 Fleet ID1 9.5 Daytime running lights 10. Diagnostics

1

Password protected menu.

37

38

MENU 7: P-heater timer

7. P-heater timer This function deals with the parking heater timer. Instructions for direct start of the P-heater can be found in the driver’s manual.

7. P-heater timer 7.1 Programming 7.2 Reset

Switch between the alternatives using ” /∇”. Confirm selection using ”SELECT”. Press ”Esc” to exit and return to the Main menu.

1

Timer programmed MENU: P-heater timer

P-heater timer

If the p-heater timer is programmed the display shows the time, date and duration information.

Program Reset 000420 Duration:

07:00 AM 1:00 7658.8 km

7.1 Programming MENU: P-Heater Timer, program

1

Select ”Program” using ” /∇”. Confirm selection using ”SELECT”. If the timer already has a time set you can overwrite the old one without carrying out a reset first.

P-heater timer

Program Reset No time programmed

Press ”Esc” to exit without changing the setting. 7658.8 km

MENU 7: P-heater timer

1

Set start date using ” ” and ”∇” then ”SELECT”. The current date is always preset.

39

P-heater timer

Set start date: 000423

7658.8 km

1

Set the start time using ” ” and ”∇” then ”SELECT”.

P-heater timer

Set start time: 07:15

7658.8 km

1

Set duration using ” ” and ”∇” then ”SELECT”. The time is set in 10–minute intervals. The longest time that can be set is two hours.

P-heater timer

Set duration: 2:00

7658.8 km

The time and date will be displayed after setting has been entered. Press ”SELECT” to return to the ”P-heater timer” menu. The P-heater timer icon appears on the status bar when the P-heater timer function is set. When the P-heater starts the icon will no longer appear on the status bar.

P-heater timer

Program Reset 000423 Duration:

07:15 AM 2:00 7658.8 km

40

MENU 7: P-heater timer

7.2 Reset MENU: P-Heater Timer, Clear To reset the P-heater timer select ”Clear” using ” /∇”. Confirm selection using ”SELECT”.

1

Press ”Esc” to exit without changing the setting.

P-heater timer

Program Reset No time programmed 7658.8 km

MENU 8: Display setting

41

8. Display setting Use the ”Display Settings” menu to change the language, units and brightness of the display. You can also change the time and date format here. To access the last menu ”Change Password” you will need to enter the correct password. Switch between the alternatives using ” /∇”. Confirm selection using ”SELECT”. Press ”Esc” to return to the main menu.

1

8. Display setting 8.1 Language 8.2 Units 8.2.1 Distance 8.2.2 Fuel Consumption 8.2.3 Temperature 8.3 Time/Date 8.3.1 AM/PM or 24h 8.3.2 Date Display 8.4 Display Light 8.4.1 Contrast 8.4.2 Backlight 8.4.3 Night display 8.5 Change Password

8.1 Language MENU: Display setting, Language 1

To set the language press ”SELECT” when you are in the Display Settings, Language menu.

2

Up to three different language alternatives appear in the display. Select a language using ” /∇” to move the marker. Confirm using ”SELECT”.

1

Display setting

1/3

Language Swedish English Deutsch

CC

7658.8 km

42

MENU 8: Display setting

8.2 Units MENU: Display Settings, Units The ”Units” menu has 3 sub-menus:

•

Distance

•

Fuel consumption

•

Temperature

Switch between the alternatives using ” /∇”. Confirm selection using ”SELECT”.

1

Press ”Esc” to exit without changing the setting.

8.2.1 Distance When ”Distance” is selected, the following will be shown on the display (with the current setting marked): Switch between the alternatives using ” /∇”. Confirm selection by pressing ”SELECT”.

1

Press ”Esc” to return to the main menu.

Display setting

1/2

Units Distance km miles

CC

7658.8 km

8.2.2 Fuel Consumption When ”Fuel Consumption” is selected, the following will be shown on the display (with the current setting marked): Switch between the alternatives using ” /∇”. Confirm selection by pressing ”SELECT”.

1

Press ”Esc” to return to the main menu.

Display setting Units Fuel consumption km/L L/100km mpg (IMP gallons) mpg (US gallons)

CC

2/4

7658.8 km

MENU 8: Display setting

43

8.2.3 Temperature When ”Temperature” is selected, the following will be shown on the display (with the current setting marked): Switch between the alternatives using ” /∇”. Confirm selection by pressing ”SELECT”.

1

Display setting

1/2

Units Temperature  C  F

Press ”Esc” to return to the main menu.

CC

7658.8 km

8.3 Time/Date MENU: Display settings, Clock format The ”Time/Date” menu has 2 sub-menus:

• •

24h or AM/PM Date format

Switch between the alternatives using ” /∇”. Confirm selection using ”SELECT”.

1

Press ”Esc” to exit without changing the setting.

8.3.1 Time When ”Time” is selected, the following will be shown on the display (with the current setting marked): AM/PM displays 12–hour format (AM = morning and PM = afternoon). Switch between the alternatives using ” /∇”. Confirm selection by pressing ”SELECT”.

Display setting

1/2

Time/Date 24 h or AM/PM 24 h AM/PM

1

Press ”Esc” to return to the main menu.

CC

7658.8 km

44

MENU 8: Display setting

8.3.2 Date Display When ”Date” is selected, the display shows y = year, m = month and d = day (with the current format marked): Switch between the alternatives using ” /∇”. Confirm selection by pressing ”SELECT”.

1

Display setting Time/Date Date format yymmdd ddmmyy mmddyy

1/3

Press ”Esc” to return to the main menu.

CC

7658.8 km

MENU 8: Display setting

45

8.4 Display Light MENU: Display Settings, Display Lighting Adjusting the rheostat which controls the instrument lighting levels will also change the brightness setting of the display when the vehicle lighting is switched on. This menu allows the backlight brightness setting of the display to be adjusted in relation to the level of the other instrument lighting. The ”Display Lighting” menu has 3 submenus:

• • •

Contrast Backlighting

Display setting

1/3

Display lighting Contrast Backlighting Night display

Night display

Switch between the alternatives using ” /∇”. Confirm selection using ”SELECT”.

1

CC

7658.8 km

Press ”Esc” to exit without changing the setting.

8.4.1 Contrast When ”Contrast” is selected the following appears on the display.

Display setting Display lighting Contrast

1/3

Increase or decrease the contrast setting using ” /∇”. Confirm selection by pressing ”SELECT”.

1

Press “Esc” to return to the main menu.

CC

7658.8 km

46

MENU 8: Display setting

8.4.2 Backlight When ”Backlight” is selected the following appears on the display.

Display setting Display lighting Backlighting

1/3

Increase or decrease the Backlight setting using ” /∇”. Confirm selection by pressing ”SELECT”.

1

Press ”Esc” to return to the main menu.

CC 8.4.3 Night display The Night display setting inverts the display. Instead of yellow text on a black background the display shows black text on a yellow background.

Display setting Display lighting Night display Inactive Active

7658.8 km 1/2

1

Press ” /∇” to move between the alternatives Disabled/Enabled. Confirm using ”SELECT”. Press ”Esc” to return to the main menu.

CC

7658.8 km

MENU 8: Display setting

47

8.5 Change Password MENU: Display Settings, Change Password The menu is only accessible if the correct password has been entered (fleet password), see “13.1 Enter password” page 75. 1

When ”Display Setting”, ”Change Password” is selected from the menu the display shows the following screen:

Display settings 1/3 Change password Workshop password 2 Transport company password Workshop password 1

2

When Workshop 1, Owner or Workshop 2 is selected the display shows: Display settings Change password Workshop password 2 Workshop password 2 0000 Enter new password: 0000

CC CC

7658.8 km

Select Workshop 1, Owner or Workshop 2 and press ”Select”. To cancel press ”Esc”.

1

1/3

7658.8 km

” /∇” increases/decreases the set value. Pressing ”SELECT” confirms your choice and moves on to the next position. ”Esc” moves the marker to the previous number, or exits from the settings.

48

MENU 9: Vehicle Settings

9. Vehicle Settings The ”Vehicle Settings” menu allows fleet owners to set targets for vehicle operation regarding max. engine speed, max. road speed and fuel consumption. The menu also deals with ammeter calibration processes, used when sensors or instruments are replaced on the vehicle. The anti-spin function can also be engaged/disengaged from this menu. Switch between the alternatives using ” /∇”. Confirm selection using ”SELECT”. Press ”Esc” to return to the main menu.

1

9. Vehicle Settings 9.1 Traction Control 9.2 Fleet Limits 9.2.1 RPM Limit (max.) 9.2.2 Speed Limit (max.) 9.2.3 Fuel Target 9.3 Ammeter calibration 9.4 Fleet ID 9.5 Daytime running lights

Action required if an information transfer is not successful:

•

Press ”Esc” and repeat the Set-up procedure again, see item 1.

•

If this does not work carry out faulttracing diagnostics on the engine control unit and display, see “10.1 Fault Diagnostics” page 57

•

Contact your dealer if necessary.

MENU 9: Vehicle Settings

49

9.1 Traction Control MENU: Vehicle settings, Traction Control When the “Traction Control” menu is selected the display shows the following:

1

Vehicle settings

1/2

Traction control On Off

” /∇” moves the cursor between Enabled and Disabled. Confirm using ”SELECT”. Press ”Esc” to return to the main menu.

CC Warning light Symbol + caution is displayed when OFF is selected. T3014424

7658.8 km

50

MENU 9: Vehicle Settings

9.2 Fleet Limits The ”Fleet Limits” menu has 3 sub-menus:

• • •

Engine speed (max)

Switch between the alternatives using ” /∇”. Confirm selection using ”SELECT”.

1

Road speed (max)

Press ”Esc” to return to the main menu.

Fuel (target)

9.2. 1 Fleet Limits: Engine speed (max) MENU: Vehicle Settings, Fleet Limits: Engine speed (max) This menu can only be accessed if the correct password has been entered. 1

Select ”Vehicle Settings”, ”Fleet Limits: Engine speed (max)” from the menu to set the engine speed limit.

2

Set the new engine speed limit using ” /∇” (enter one number at a time followed by ”SELECT”).

This setting can be used by the vehicle owner to set a maximum engine speed limit. If the engine speed exceeds the set limit, it is registered, see “12.3 Trip data” page 71 3

Vehicle Settings 1/2 Fleet Limits (engine speed)

1

Present Limit: Transfer An is complete.

Vehicle Settings 1/3 Fleet Limits (engine speed) Present Limit: 2000 rpm Set new value: 0 0 0 0 rpm

CC

7658.8 km

Press ”Esc” to exit and return to the previous menu. Press ”SELECT” when required engine speed limit (rpm) is displayed.

The display will indicate whether the transfer has been successful. Press ”Esc” to return to the previous menu.

CC 4

7658.8 km

The display will indicate if the transfer was not successful. See “Action required if an information transfer is not successful: ” page 48.

MENU 9: Vehicle Settings

51

9.2.2 Fleet Limits: Road speed (max) MENU: Vehicle Settings, Fleet Limits: Road speed (max) This menu can only be accessed if the correct password has been entered. This setting can be used by the vehicle owner to set a road speed limit. If the vehicle exceeds the speed limit, it well be registered, see “12.3 Trip data” page 71 1

Select ”Vehicle Settings”, ”Fleet Limits: Road speed (max)” from the menu to set the road speed limit.

2

Set the new road speed limit using ” /∇” (enter one number at a time followed by ”SELECT”).

3

1

Vehicle Settings 2/3 Fleet Limits (road speed) Present Limit: 50 km/h Enter new value: 0 0 0 km/h

CC 4

CC

7658.8 km

Press ”Esc” to cancel without making changes and return to the previous menu. Press ”SELECT” when required road speed limit has been entered.

The display will indicate whether the transfer has been successful. Press ”Esc” to return to the previous menu. Vehicle Settings 2/3 Fleet Limits (road speed) Present value: Transfer An is complete.

7658.8 km

The display will indicate if the transfer was not successful. Press “Esc” and repeat the Set-up procedure again, see item 1. If this does not work carry out faulttracing diagnostics on the display, see “10.1 Fault Diagnostics” page 57 Contact your dealer if necessary.

52

MENU 9: Vehicle Settings

9.2.3 Fleet Limits: Fuel (target) MENU: Vehicle Settings, Fleet Limits: Fuel (target) This menu can only be accessed if the correct password has been entered. This setting makes it possible to set a fleet fuel target. For information on fuel consumption for a journey, see “12.3 Trip data” page 71 1

Select ”Vehicle Settings”, ”Fleet Limits: Fuel (target)” from the menu to set the fuel target.

2

Set the new target using ” /∇” (enter one number at a time followed by ”SELECT”).

3

1

Vehicle Settings Fleet Limits (fuel)

The display will indicate whether the transfer has been successful. Press ”Esc” to return to the previous menu. Vehicle Settings 3/3 Fleet Limits (fuel) Present value: Transfer An is complete.

3/3

Present value: 34 l/100 km Enter new value: 0 0 l/100 km

CC 4

CC

7658.8 km

Press ”Esc” to exit and return to the previous menu without saving changes. Press ”SELECT” when required target has been entered.

7658.8 km

The display will indicate if the transfer was not successful. Press “Esc” and repeat the Set-up procedure again, see item 1. If this does not work carry out faulttracing diagnostics on the display, see “10.1 Fault Diagnostics” page 57 Contact your dealer if necessary.

MENU 9: Vehicle Settings

53

9.3 Ammeter calibration MENU: Vehicle settings, ammeter calibr.

2

Sensors or instruments which are replaced must be calibrated using an ammeter. 1

When the ignition key is turned to the stop position the display will show the following: Vehicle Settings

Select ”Vehicle Settings”, ”Ammeter calibr:” from the menu and follow the instructions below.

Ammeter calibr.

Vehicle Settings Ammeter calibr. Switch off all power consumers, then switch off the ignition.

Calibration in progress, please wait.

CC CC

7658.8 km

The operation can be cancelled by turning the ignition key to the drive position or by pressing ”Esc”. If the calibration is cancelled using ”Esc”, the display switches off.

7658.8 km

3

When the calibration is completed the following message is displayed: Vehicle Settings Ammeter calibr. Sensor component changed -5A Switch on the ignition.

CC

7658.8 km

54

MENU 9: Vehicle Settings

9.4 Fleet ID MENU: Vehicle Settings, Fleet ID This menu can only be accessed if the correct password has been entered. The owner can enter the fleet id of the vehicle in this menu if required. Data registered in the engine control unit is then registered for this ID. 1

Select ”Vehicle Settings”, ”Fleet ID” from the menu. Enter the new Fleet ID using ” /∇” (enter one number at a time followed by ”SELECT”). 13 characters must be entered (blank characters are entered in unused positions).

2

1

The display will indicate whether the transfer has been successful. Press ”Esc” to return to the previous menu. Vehicle Settings Fleet id Fleet id:

Vehicle Settings Fleet ID Fleet ID:

An

Transfer is complete.

XXXX Enter new Fleet ID:

CC CC

7658.8 km

Press ”Esc” to exit and return to the previous menu. Press ”SELECT” when the fleet ID has been entered.

3

7658.8 km

The display will indicate if the transfer was not successful. Press “Esc” and repeat the Set-up procedure again, see item 1. If this does not work carry out faulttracing diagnostics on the display, see “10.1 Fault Diagnostics” page 57 Contact your dealer if necessary.

MENU 9: Vehicle Settings

55

9.5 Daytime running lights MENU: Vehicle settings, Daytime running lights The daytime running lights can be switched off in this menu. If the Daytime running lights function is ”Off” then dipped beams have to be switched on and off using the light switch on the panel.

Vehicle settings

1/2

Daytime running lights On Off

CC

7658.8 km

56

MENU 10: Diagnostics

10. Diagnostics The ”Diagnostics” menu enables faulttracing on the control units in the vehicle to check for faults. It is also possible to run an instrument test to check the integrity of gauges and LEDs. The part number of the control unit can be identified from the part number menu. Switch between the alternatives using ” /∇”. Confirm selection using ”SELECT”. Press ”Esc” to return to the main menu.

1

10. Diagnostics 10.1 Fault Diagnostics 10.2 Cluster Selftest 10.2.1 Indicator light test 10.2.2 Gauge test 10.2.3 Display test 10.2.4 Loudspeaker test 10.3 Part Number

Action required if an information transfer is not successful:

•

Press ”Esc” and repeat the Set-up procedure again, see item 1.

•

If this does not work carry out faulttracing diagnostics on the engine control unit and display, see “10.1 Fault Diagnostics” page 57

•

Contact your dealer if necessary.

MENU 10: Diagnostics

57

10.1 Fault Diagnostics MENU: Diagnostics, Fault Diagnostics A list of the control units on the vehicle is displayed in the ”Fault diagnostic” menu.

1

Select the control unit using ” /∇”. ”Select” confirms the control unit selection. To cancel press ”Esc”. Fault diagnostics Diagnostics

1/3

Engine control unit

Fault diagnostics

Brake control unit

⇒

Cluster Selftest Part number

Gearbox Gear control Retarder control unit Vehicle control unit

CC

7658.8 km

Display Air suspension Body builder module Climate unit Airbag Light control unit Telephone Anti-theft protection Transport information system Steering Wheel Module

1/15

58

MENU 10: Diagnostics

1

The display will show the transfer progress while the selected control unit is being contacted, see flowchart page 60

2

If the control unit selected has no faults ”No faults” is displayed. Press ”Esc” to return to the previous menu.

3

tered since the latest reset. If no information is available for the amount of times a fault code has been registered it will be displayed as being ”Active” (fault remains). Alternatively it may display ”Inactive” (the fault was present earlier). 6

If the control unit selected does not respond within 5 seconds ”Action unsuccessful” is displayed. Go to ”Actions if transfer is unsuccessful”, see “10. Diagnostics” page 56

1

Press ”Esc” to return to the previous menu. 4

The following can be displayed if the selected control unit has fault codes: Diagnostics 1/7 Fault diagnostics Engine Air temperature, intake Electrical fault Active Number of events: ”03” More info? Press

CC 5

7658.8 km

This will show: 1: Control unit ID 2: Identification of parameter/component 3: Fault type ID 4: Fault active/inactive 5: ”Total occurrences” displays how many times the fault has been regis-

The digits in the upper right corner (”1/7” in this example) show the number of fault codes (”7”)and which number in the order which is displayed the fault code has (”1”). ” /∇” moves the cursor and the next fault code/message will be displayed. ”Reset All” is the last item in the list. This reset deletes only the fault codes for the control unit selected.

7

If there are more than 20 fault codes/messages for the selected control unit, the 21st message will be:

Diagnostics Fault diagnostics Engine

1/7

Too many fault messages

CC

7658.8 km

To be able to see the messages that are not shown, one or more of the first messages must first be reset.

MENU 10: Diagnostics 8

Press ”SELECT” for more information on the fault code. The fault codes below are shown in numerical order. If the fault is inactive the time and date when the fault occurred will be shown together with other information. Diagnostics Fault diagnostics Engine 1/7 MID 128 SID 231 FMI 12 First: 00:42 000701 Last: 15:36 000703 Reset? Hold for 1s.

CC

7658.8 km

To reset the fault codes press ”SELECT” for 1 second. MID: Control unit ID PID: Identification of parameter PPID Volvo-unique identification of parameter SID: Identification of component PSID: Volvo-unique identification of component FMI: Identification of fault type

59

60

MENU 10: Diagnostics Data transfer

⇒

in progress, please wait. Engine

No errors

Action

1/7

Air temperature, intake

failed Electrical fault Inactive Number of events: ”06” More info? Press

Engine

1/1

MID 128

PID 105

FMI 3

First:

7/7 Reset all faults of this MID?

00:42

000701

Press

Last:

for 1 s.

This box is

15:36

000703

always last if

Reset? Hold

for 1s.

more than 1 fault present.

Data transfer in progress, please wait.

Action

Transfer

failed

completed

MENU 10: Diagnostics 10.2 Cluster Selftest MENU: Diagnostics, Cluster The following sub-menus can be accessed:

• • • •

Indicator lamp test Gauge test Display test Loudspeaker test

Cancel test Press ”Esc” to cancel the test.

61

62

MENU 10: Diagnostics

10.2.1 Indicator light test MENU: Diagnostics, Cluster, Telltales, LEDs 1

Select ”Indicator light test, LEDs”.

2

The indicator lights come on for approx. 5 seconds.

3

”Esc” cancels the test and returns to the ”Indicator light test, LEDs” menu.

10.2.2 Gauge test MENU: Diagnostics, Cluster, Gauge test 1

Select ”Gauge test”.

2

The gauges perform a diagnostic scan. The pointers move back and forth a few times, between the end positions. They should not display any specific value. This is just a check to ensure they can move (i.e. that the gauge and the exciter are working.)

3

”Esc” cancels the test and returns to the ”Gauge test” menu.

MENU 10: Diagnostics 10.2.3 Display test MENU: Diagnostics, Cluster, Display test 1

Select ”Display test”.

2

The entire display will light up for 3 seconds and then go out for 3 seconds. A test pattern will then appear for about 3 seconds. The test pattern will then be displayed inverted for 3 seconds.

3

”Esc” cancels the test and returns to the ”Display test” menu.

10.2.4 Loudspeaker test MENU: Diagnostics, Cluster, Loudspeaker test 1

Select ”Loudspeaker test”.

2

The description of each sound will be displayed while the sound is activated for about 10 seconds. Use ” /∇” to switch between the various sounds.

1

3

”Esc” cancels the test and returns to the ”Sound test” menu.

63

64

MENU 10: Diagnostics

10.3 Part Number MENU: Diagnostics, Part Number A list of the control units on board the vehicle is displayed in the ”Part Number” menu. Part number Diagnostics

3/3

Engine control unit

Fault diagnostics

Brake control unit

⇒

Cluster Selftest Part number

Gearbox Gear control Retarder control unit Vehicle control unit

CC

7658.8 km

Display Air suspension Body builder module Climate unit Airbag Light control unit Telephone Anti-theft protection Transport information system Steering Wheel Module

1/15

MENU 10: Diagnostics

1

1

” /∇” moves the cursor through the list.

2

”SELECT” confirms the control unit selection.

3

The display shows:

Diagnostics

1/15

Fault diagnostics En Br Data transfer LH in progress, LH please wait. Tr Vehicle control unit Display

CC 4

If there is a communication error the display shows: Diagnostics Part number Hardware number: No data Software number: No data

CC

7658.8 km

The following message is displayed:

Diagnostics Part number Display Hardware number: 020428693P01 01392017 250901 Software number: 20428728.P01 20428654.P0120428732.P01

CC

5

7658.8 km

65

7658.8 km

66

MENU 11: Vehicle data

11. Vehicle data The engine oil level can be checked in the ”Vehicle Data” menu.

11. Vehicle data 11.1 Oil level

11.1 Oil level MENU: Vehicle Data, Oil level The vehicle is equipped with an electronic oil level sensor. The bar marked min and max shows the engine oil level. The number in the middle indicates the difference in litres between the min and max level. The engine oil level is also displayed when the key is turned to the On position. It is displayed for 5 seconds or until the engine is started and is shown directly after SRS and the welcome message. For the reading to be correct the engine must have been switched off for at least 70 minutes. If the engine has not been switched off for long enough, the number of minutes delay until the gauge is able to show an accurate reading will be displayed, see illustration. If the engine oil level is at ”min” or below ”min” a warning message is displayed, see illustration. Note! No low oil level warning is displayed while driving. Note! The engine oil level should be between ”min” and ”max”. Do not top up with oil until the level is near ”min”. Too much oil in the engine can increase oil consumption.

Time to correct value: Service Oil level Correct value within 5 min.

min<

6L

CC

> max 7658.8 km

Low Oil Level:

min<

CC

6L

>max 7658.8 km

MENU 11: Vehicle data 11.2 Load Indicator MENU: Vehicle Data, Load Indicator Read the information on the load indicator function in the driver’s manual.

67

68

MENU 12: Data log

12. Data log The ”Data log” menu has several submenus that are not password protected and 1 sub-menu that is password protected.

• • •

Vehicle number Total data

12.1 Vehicle number 12.2 Total data 12.3 Trip data 12.4 Reset Trip data

Trip data

Password is required:

•

12. Data log

Reset trip data

Switch between the alternatives using ” /∇”. Confirm selection using ”SELECT”. Press ”Esc” to return to the main menu.

1

Action required if an information transfer is not successful:

•

Press ”Esc” and repeat procedure again, see item 1.

•

If this does not work carry out faulttracing diagnostics on the engine control unit and display, see “10.1 Fault Diagnostics” page 57

•

Contact your dealer if necessary.

MENU 12: Data log

69

12.1 Vehicle number MENU: Datalog, Vehicle number 1

Select ”Datalog”, ”Vehicle number”.

2

The fleet id that is displayed has been entered in the menu: “9.4 Fleet ID” page 54. Press ”Esc” to return to the previous menu.

3

If the transfer should fail, the following message is shown:

Data log Vehicle number

Action failed

Data log Vehicle number Fleet id: 0000000

CC

Chassis number: 0000000

CC

7658.8 km

7658.8 km

70

MENU 12: Data log

12.2 Total data MENU: Data log, Total data Totals indicate the accumulated engine values that have been logged during the lifetime of the engine control unit. Six different totals are stored. 1

Select ”Data log”, ”Total data”.

2

The menus showing ”Total Data” can be scrolled through one by one on the list using ” /∇”. Two totals are shown at a time. Press ”Esc” to quit.

5 Data log Total data

1

5/6

Total PTO hours:

3

0.0 h Data log Total data

Total number engine revs:

1/6

0r Total distance:

CC

0.0 km Total Fuel consumption:

6 0.0 l

CC

7658.8 km

4 Data log Total data

3/6

Total number of hours engine hours: 0.0 h Total idling time: 0.0 h

CC

7658.8 km

7658.8 km

If the data transfer is unsuccessful ”No data” is displayed where data is missing.

MENU 12: Data log

12.3 Trip data MENU: Data log, Trip data There are 14 different trip data values stored. Note! The trip data must be reset before each measurement, see “12.4 Reset Trip data” page 73 1

Select Data log, Trip data. Data log Trip data Distance driven trip:

1/14

000 km Trip average fuel consumption: 0.0 l/km

CC 2

7658.8 km

Trip values are shown two at a time on a scroll list and can be browsed using ” /∇”. The available trip data is listed below.

1

Press ”Esc” to quit. If the data transfer is unsuccessful ”No data” is displayed where data is missing.

71

72

MENU 12: Data log

Trip data, scrolling list Distance driven

Speed too high

trip:

during trip: 000 km

0.0 h

Trip average

Engine operating hours

fuel consumption:

during trip:

0.0 l/km

0.0 h

Trip total

Idle time during

fuel consumption:

trip:

0.0 l/km

0.0 h

Overspeed

Consumption on

during trip:

idle during trip: 0.0 h

0.0 l

Uneconomical engine speed

Power take-off during

during trip:

trip: 0.0 h

0.0 h

Trip consumption

Consumption with power take-

at uneconomic engine speed:

off during trip:

0.0 l

0.0 l

Trip average

Time with Cruise Control

speed:

during trip: 0.0 km/h

0.0 h

MENU 12: Data log

73

12.4 Reset Trip data MENU: Data log, Reset trip data This menu can only be accessed if the correct password has been entered. 1

Select ”Data log”, ”Reset trip data”.

2

Select Reset. Press ”SELECT”. Press ”Esc” to quit.

4

Data log Reset trip data

Data log Reset trip data Reset all Trip data? Press for 1s.

CC

Reset all re Transfer Tr completed.

7658.8 km

CC

3

5 Data log Reset trip data

7658.8 km

If the reset fails, the following message is shown: Data log Reset trip data Reset all

Reset all re Data transfer Tr in progress, please wait

CC

Then the following message is displayed:

re Action Tr failed

7658.8 km

CC

7658.8 km

74

MENU 13: Password

13. Password Password, general information Certain functions are password protected and there are a number of passwords for the display (it is also possible to disable password protection for functions, which is useful when the owner is the driver. This function can be set by a Volvo workshop): 1

Workshop, password 1

2

Transport company, password

3

Workshop, password 2

These passwords give the user access to all password-protected functions with certain exceptions: The Workshop password does not give access to password configuration, i.e. the Owner, Workshop and Driver passwords cannot be changed. The password for a new vehicle is programmed during manufacture. The workshop password 2 is: 0000 Note! This password must be changed to prevent unauthorised access to the menus. See “8.5 Change Password” page 47 to change the password. Switch between the alternatives using ” /∇”. Confirm selection using ”SELECT”. Press ”Esc” to return to the main menu.

1

13. Password 13.1 Enter password The following menus are password protected and marked with a key symbol in the menus:

• • • • •

Fleet limit: engine speed Fleet limit: speed Fleet Limits: fuel Fleet id Reset (applies to a number of functions)

When the ignition key has been in the stop position for more than 60 seconds or the batteries have been disconnected, the password must be entered again in order to access all the functions. No functions should be password protected: To make all menus available without password you must go to MENU: ”Password” and press ”SELECT”. You can also go to a password protected menu and press ”SELECT”. A password entry box will then be displayed.

MENU 13: Password

75

13.1 Enter password MENU: Password 1

Select the ”Password” menu.

P-heater timer Display setting Vehicle Settings Diagnostics Service Data log Password

CC 2

7/7

3

If an incorrect password is entered then the user is returned to point 2. Re-enter the password using ” /∇” followed by ”Select” on the control stalk as in point 2.

1

7658.8 km

The password consists of a four digit number, 0000–9999, that is scrolled forward using ” /∇” on the control lever (one number at a time) followed by ”SELECT”. The display shows the following:

1

Password For more menus Enter the password: 0000

CC

Note! When the ignition key has been in the stop position for more than 60 seconds or the batteries have been disconnected, the password must be entered again in order to access all the functions.

7658.8 km

Press ”SELECT” when the correct password has been entered.

Index

77

Index A

B

C

D

E F

Acknowledging messages . . . . Action required if an information transfer is not successful: . . . . Alarm clock . . . . . . . . . . Alarm clock, activating . . . . . Alarm clock, turning off . . . . Ammeter . . . . . . . . . . . Ammeter calibration . . . . . . Average speed . . . . . . . . .

12 48 26 27 27 20 53 29

G

I Backlighting . . . . . . . . . . 32 Black Panel . . . . . . . . . . 31 Changing password Changing settings Clock format . . Cluster Selftest . . Control stalk . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

47 5 43 61 3

L

Data log . . . . . . . Date format . . . . . Daytime running lights Diagnostics . . . . . Display . . . . . . . Display control stalk . Display lighting . . . Display menus . . . . Display setting . . . . Display symbols . . . Display test . . . . . Display, general . . .

. . . . . . . . . . . .

. . . . . . . . . . . .

. . . . . . . . . . . .

. . . . . . . . . . . .

. . . . . . . . . . . .

68 43 55 56 31 3 45 4 41 7 63 1

M

Estimated time of arrival

. . . . 30

Fault diagnostics . . . . . . . . Favourite Display . . . . . . . Fleet id . . . . . . . . . . . . Fleet Limits: Engine speed (max)

57 32 54 50

N

Fleet Limits: Fuel (target) . . . Fleet Limits: Road speed (max) Fleet target . . . . . . . . . Fuel consumption . . . . . . Fuel data . . . . . . . . . .

. . . . .

52 51 50 22 21

Gauge test . . . . . . . . Gauges . . . . . . . . . Gear position . . . . . . Give distance to destination

. . . .

62 18 18 30

. . . .

. . . .

Indicator light test, LEDs . . . . 62 Information messages . . . . . . 11 Introduction . . . . . . . . . . 1 Language . . . . . . Leg fuel . . . . . . . Load indicator . . . . Location and content of Loudspeaker test . . .

. . . . . . . . . . . . display . . . .

. . . . .

41 23 67 2 63

MENU 10: Diagnostics . . . . . MENU 11: Vehicle data . . . . . MENU 12: Data log . . . . . . MENU 13: Password . . . . . . MENU 1: Gauges . . . . . . . MENU 2: Fuel data . . . . . . MENU 3: Time/distance . . . . MENU 4: Display . . . . . . . MENU 5: Vehicle messages . . . MENU 6: Reset . . . . . . . . MENU 7: P-heater timer . . . . MENU 8: Display setting . . . . MENU 9: Vehicle Settings . . . Menus . . . . . . . . . . 14, Menus when vehicle stationary . Menus when vehicle stationary. . Messages . . . . . . . . . . .

56 66 68 74 18 21 24 31 35 36 38 41 48 15 37 37 11

78

Index

Night/day . . . . . . . . . . . 34 O

P

R

S

T

Oil level . . . . . . . . . . . . 66 Outside temperature . . . . . . 19 P-heater timer . Part number . . Password . . . Pressure, primary

. . . . . . . . . tank

. . . .

. . . .

. . . .

. . . . 74, . .

38 64 75 20

Remaining fuel . . . . Reset . . . . . . . . Reset average speed . Reset fuel consumption Reset the tripmeter . . Reset trip data . . . . Resetting, fuel data . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

23 36 29 22 28 73 23

Selecting a menu . . . Setting the alarm clock Setting the clock . . . Stop messages . . . .

. . . .

. . . .

. . . .

. . . .

. . . .

4 26 25 11

U V

W

Temperature, engine oil Temperature, gearbox . Time and date . . . . Time/distance . . . . Total data . . . . . . Traction control . . . Trip data . . . . . . Tripmeter . . . . . .

. . . . . . . .

. . . . . . . .

. . . . . . . .

. . . . . . . .

. . . . . . . .

19 19 25 24 70 49 71 28

Units . . . . . . . . . . . . . 42 Vehicle data . . Vehicle messages Vehicle number Vehicle Settings Voltmeter . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

66 35 69 48 20

Warning messages . . . . . . . 11 Warning, icy road conditions . . 13

Volvo Truck Corporation Göteborg, Sweden

20 160726 English .01.2002

Printed in Sweden