Material Safety Data Sheet: Special Impregnation Sealant TSP - 99

Material Safety Data Sheet SPECIAL IMPREGNATION SEALANT TSP - 99 Page : 1/6 Date of Issue: 01/01/2016

Last change: 01/03/2018

1. Chemical Product and Company Identification Product Data - Trade Name

Special Impregnation Sealant TSP-99

- Article No.

– Unavailable

- Composition No.

–Unavailable

- Use of the Substance/Preparation - Impregnation sealant to seal porous castings. - Manufacturer’s Name / Supplier

- Teknoseal Engineering Solutions # Bindu Apartments,Plot No.54 Lane No.3. Ananad Park,Aundh, Pune – 411007. India.

- Telephone

- +919823270427 , +919822038423

- E-mail

- [email protected]

2.Composition / Information on Ingredients

- Chemical name

Mixture/Blend of mono- and polyfunctional Acrylate, Methacrylate – Monomers

3.Hazard Identification

- For humans

May cause irritations to eyes, respiratory system and skin . May cause sensitization on skin contact.

4.First Aid Measures. - Inhalation

Move person to fresh air. Get medical attention incase of discomfort

- Skin contact

Remove person from source of contamination Remove contaminated clothing and footwear.

Revision Date : 01/03/2018

Page : 2/6

Wash with soap and water. Get medical persists

attention incase discomfort - Eye contact

-

Ingestion

Remove person from source of contamination. Wash eyes with plenty of water with eyes open at all times for minimum 15minutes .Get medical advice. Do not induce vomiting . Rinse the mouth thoroughly and get medical attention.

5.Fire Fighting Measures

Flash Point

: 102 Deg. C

Recommended Extinguishing Agent : Carbon dioxide,foam, Dry powder chemical Special fire fighting proceedure

:Wear individual breathing apparatus . Wear full protective clothing , Gloves and eye/face protection

Hazardous combustion products

: Oxides of Sulphur , Carbon and Nitrogen . Irritatiing organic vapours.

Unusual fire or explosion hazards

: None expected .However incase of unexpected fire do not breathe fumes. Cool the container with sprayed water to avoid polymerization .

.

6.Accidental Release Measures - Personal precautions

Wear proper protective equipment .

- Enviromental precaution

Do not allow product to enter sewers , drains or surface waters.

- Clean up measures

Soak up the spilled material with inert absorbent material (sand , saw dust , silica gel or acid binder) and store in a partly full , closed container until it is disposed . Spray the area with water after clean up.

7.Handling and Storage - Handling

Prevent contact with eyes ,skin and clothing . Do not breathe vapour and mist. Wash Thoroughly after handling.

Revision Date : 01/03/2018

- Storage Temperature :

-

Pot life (under normal operating condition)

-

Shelf life:(under normal storage condition) - Recommendation for storage in containers ( drums , cans).

- To Avoid :Incompatible Materials

Page : 3/6

Non catalysed resin from 10OC to 35OC Catalysed resin from 10 OC to 25OC Indefinite 12 Months (non catalysed) Make sure of the presence of air in drums or containers. Keep only at temperature recommended as above . Keep container tightly closed until ready for use and keep it away from UV radiation or sunlight or X rays. Keep container to avoid contact from oxidizing acids , bases and do not keep under inert gas (nitrogen,.)

8.Exposure Controls / Personal Protection The factory/place of work should have good ventilation .

9.

- Protective equipment

Avoid contact with skin , eyes and face. Wear safety goggles , or safety glasses with side shields and protect face with face goggles if splashing is a possibility . Wear protective clothing.

-(General preventive & hygiene measures)

Take off all contaminated clothing When using do not eat, drink, or Smoke .Wash hands immediately after handling the products , before the breaks .

- Inhalation protection

Local ventilation is recommended.

- Skin and hand protection

Do not use natural rubber gloves. Use impermeable gloves and protective clothing as necessary to prevent skin contact . Wear nitrile gloves .Replace gloves immediately when torn or any change in appearance(dimension colour , flexibility,etc) is noticed.

Physical and Chemical Properties - Appearance

Liquid

Revision Date : 01/03/2018

Page : 4/6

- Colour

Clear transparent

- Odour

Ester- like

- Change of state conditions - Melting point

-35 OC

- Boiling point

240 OC at 1013 mbar

- Flash point

102O C DIN 51758

- Ignition temperature

> 200 O C

- Explosion

no danger of explosion

- Vapour pressure

0.1 mbar at 20 OC,1.3 mbar at 66OC

- Density

1.060 +/ - 0.006 g/ ml at 20OC

- Solubility in water

106-108 g/l at 20 OC

- Solubility in organic solvents

completely soluble in most organic solvent

- PH –value

6–7

- Viscosity

28 +/- 2 Sec. Zahn Cup No.1

10. Stability and Reactivity - Stability

Stable under normal conditions of storage and use.

- Condition to avoid

Keep away from Direct UV / sunlight, strong heat ,absence of oxygen ,ignition sources and incompatible materials .

- Dangerous reaction with

Hazardous polymerization may occur at elevated temperatures, or in the presence of excess oxidizing agents(e.g. peroxides) , Concentrated bases and acids .

- Hazardous decomposition

No hazardous products if used as per instructions .However incase of polymerization, due to excess heat generated , thermal decomposition may occur resulting in formation,oxides of carbon , nitrogen and irritating organic vapours.

- Hazardous Polymerization

Polymerization may occur due to over catalysation or insufficient aeration after catalysation or with the development of strong heat.

Revision Date : 01/03/2018

Page : 5/6

11.Toxicological Information Acute toxicity data - Inhalation

May cause respiratory tract irritation

- Ingestion (LC50 Rat,[ mg/kg])

11200

- Skin contact

May cause allergic skin reaction

- Caustic effect (skin / Eye )

Irritation to eyes and skin.

- Sensitization

May cause sensitization on skin contact.

Subacute / chronic toxicity data - Carcinogenic

unavailable

- Mutagene

unavailable

- Teratogenic

unavailable

- Narcotic effect

unavailable

Experiences from the practice - Observation for classificatioin

none

- Other observation

none

- General remarks

Classification according to method of calculation.

12.Ecological Information

Unavailable . Do not allow entry into drains or sewers.

13.Disposal consideration

Dispose off according to the federal state and local regulations .

14.Transport Information

- Land transport

not classified

- Inland navigation

not classified

- Ocean traffic

not classified

- Air freight

not classified

Revision Date : 01/03/2018

Page : 6/6

15.Regulatory Information - Classified according to EEC directives

The product is classified as an irritant by EEC regulation of dangerous products

- Letter of classification



Xi – irritant

- R-Sentences R36/38-Irritation to eyes and skin - S-Sentences S2-Keep out of reach of children . S24/25-Avoid contact with skin and eyes. S26-In case of contact with eyes rinse immediately with copius amounts of water and seek medical advice. S37/39-Wear suitable gloves and eye/face protection. S46- If swallowed seek medical advice immediately and show this container or lable. -

National regulations a. Vbf

not applicable

b. Air pollution regulation

not classified

c. TA-air Class; No; Amount m % d. Water pollution class

Class II 5 . 2 ; > 75 Not listed

16.Other Information The information above is believed to be correct but does not purpose to be all inclusive and shall only be used as a guide . Please note that Teknoseal Engineering Solutions shall not be held liable for any damage resulting from the handling or from contact with the above material.