Felcom18 Felcom19 Service Manual A

SERVICE MANUAL - INMARSAT-C MOBILE EARTH STATION Ku-BAND - INMARSAT MINI-C VSAT MOBILE EARTH STATION MODEL

FELECOM FV-100 18, 19

FELCOM 19

FELCOM 18

CONFIDENTIAL for Internal Use Only This document is only for a service staff of FURUNO products. Any unauthorized reproduction of any of its content is prohibited.

www.furuno.co.jp

The paper used in this manual is elemental chlorine free.

・FURUNO Authorized Distributor/Dealer 9-52 Ashihara-cho, Nishinomiya, 662-8580, JAPAN

All rights reserved.

Printed in Japan

A : DEC . 2012

Pub. No. SME-56740-A (NAYO )

FELCOM18/19

*00017743510* *00017743510* * 0 0 0 1 7 7 4 3 5 1 0 *

Contents Contents

Summary Chapter 1. Overview 1.1 Overview··········································································································1-1 1.1.1 Overview ···································································································1-1 1.1.2 Configuration ·····························································································1-2 1.1.3 Overview of Connection Port ····································································1-3 1. Connection of ADE and BDE ······································································1-3 2. [LAN] port ···································································································1-3 3. [DTE] port (FELCOM 18) ············································································1-3 4. [JUNCTION] port ························································································1-4 5. [D-GPS] port ·······························································································1-4 6. [PRINTER] port ··························································································1-4 1.1.4 Compatibility ·····························································································1-5 1. Compatibility of Antenna unit ······································································1-5 2. Compatibility of BDE board ········································································1-5 1.2 Handling of Alarm ····························································································1-6

Chapter 2. Menu Tree 2.1 Outline of menu operation ···············································································2-1 2.1.1 Menu operation for each Mode ·································································2-1 2.1.2 Settings for each Destination Type····························································2-3 1. Priority: Normal ···························································································2-3 2. Priority: Distress ·························································································2-3 2.2 Menu tree for FELCOM 18 terminal unit ··························································2-4 [Report] menu in SSAS Manager Mode ···························································2-10 2.3 FELCOM 19 Menu Tree················································································· 2-19

Chapter 3. Parts Location 3.1 BDE: FELCOM 18 ···························································································3-1 3.2 BDE: FELCOM 19 ···························································································3-7 3.3 ADE ··············································································································· 3-10

i CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Contents

3.4 Other unit ·······································································································3-13 3.4.1 JUNCTION BOX: IC-318········································································· 3-13 3.4.2 DISTRESS ALERT/RECEIVED CALL UNIT: IC-305 ······························· 3-14 3.4.3 ALARM UNIT: IC-306 ·············································································· 3-15 3.4.4 SSAS ALERT UNIT: IC-307····································································· 3-17

Chapter 4. System setup 4.1 Setup Menu ·····································································································4-1 4.1.1 System Setup ····························································································4-1 1. FELCOM 18 ·······························································································4-1 2. FELCOM 19 ·······························································································4-3 3. Handling of EXT Nav Data··········································································4-4 4. Handling of INT Nav Data ···········································································4-6 4.1.2 Outline of Command Window ···································································4-7 4.2 FELCOM 18: Setting IC-305 and IC-306 ·························································4-9 4.2.1 Jumper setting ··························································································4-9 4.2.2 ON/OFF setting ······················································································· 4-10 4.2.3 Testing IC-305 and IC-306 ······································································ 4-11 1. IC-305 ······································································································ 4-11 2. IC-306······································································································· 4-12 4.3 FELCOM 18: Setting IC-350 ··········································································4-12 4.3.1 Setting IC-350 ························································································· 4-12 4.3.2 ON/OFF setting for IC-350 (Command Window) ···································· 4-13 4.3.3 Testing IC-350 ························································································· 4-14 4.4 FELCOM 18, 19 External Alarm Setup ··························································4-15 4.5 FELCOM 18 and 19: Setting SSAS ······························································· 4-17 Points for operation ·························································································· 4-17 4.5.1 Jumper Setting ························································································ 4-19 4.5.2 ON/OFF setting ······················································································· 4-20 4.5.3 SSAS mode ····························································································4-21 1. Entering SSAS Manager Mode ································································4-22 2. Changing the password for entering SSAS Manager Mode ····················· 4-23 4.5.4 Editing the SSAS Report ········································································· 4-25 1. Setting SSAS Report ················································································ 4-25 2. Setting Message Contents ······································································· 4-27 4.5.5 Testing the Alert button on IC-307 ··························································· 4-28 4.5.6 Sending the Test message (executing test mode)··································· 4-30 1. If FELCOM 18 or FELCOM 19 is connected with the PC terminal ··········· 4-30 2. If PC terminal is not connected with FELCOM 19 ···································· 4-31 2.1) SSAS Standard mode, Russian Mode ···············································4-31 2.2) USCG Mode ······················································································4-33

ii CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Contents

4.6 Data Report ··································································································· 4-35 4.6.1 Overview ································································································· 4-35 1. Overview ·································································································· 4-35 2. Types of Data Report protocols ································································ 4-36 3. Sharing VMS and LRIT············································································· 4-36 4. Data Report by operating menu································································ 4-37 5. Displaying Data Report············································································· 4-37 4.6.2 Enabling/Disabling DNID········································································· 4-38 4.6.3 VMS setting ·····························································································4-40 1. Setting VMS ON ······················································································· 4-40 2. Setting VMS OFF ····················································································· 4-43 3. Checking the VMS setting ········································································4-45 4. Editing the VMS setting file (reference) ···················································· 4-46 5. Setting E-FORM ······················································································· 4-51 6. Activating E-FORM ··················································································· 4-51 7. Opening E-FORM ····················································································· 4-52 4.6.4 ON/OFF setting for LRIT Mode ·······························································4-54 4.6.5 Checking the operation status of Program Report ·································· 4-56

Chapter 5. Block Description 5.1 Configuration ···································································································5-1 5.1.1 Configuration of the board·········································································5-1 1. FELCOM 18 ·······························································································5-1 2. FELCOM 19 ·······························································································5-2 5.1.2 Major functions of the board······································································5-2 5.2 ADE ·················································································································5-4 5.2.1 Outline of Antenna unit··············································································5-4 5.2.2 Antenna element ·······················································································5-5 5.2.3 ANT RF ·····································································································5-6 5.3 BDE ·················································································································5-8 5.3.1 RF CON ····································································································5-8 1. Transmit circuit ···························································································5-8 2. Receiving circuit ·························································································5-9 3. PLL circuit ···································································································5-9 5.3.2 TERMCPU: 16P0283B (FELCOM 18) ···················································· 5-11 5.3.3 COMMCPU: 16P0282 (FELCOM 19)······················································ 5-15 5.3.4 TERMPWR: 16P0287B (FELCOM 18) ···················································· 5-17 5.3.5 COMMPWR: 16P0288 (FELCOM 19) ····················································· 5-19

iii CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Contents

Chapter 6. Updating program 6.1 Summary ·········································································································6-1 1. Procedure for updating program ····································································6-1 2. Program file list ······························································································6-1 3. Notes··············································································································6-1 4. Checking program version ·············································································6-2 6.2 Procedure for updating the program ································································6-4 6.2.1 Updating the program via LAN: Updater ···················································6-4 6.2.2 Updating the program via LAN: upf18term.bat ··········································6-7 6.2.3 Updating program via SD card (FELCOM 18) ···········································6-9

Chapter 7. PC terminal 7.1 Installing PC terminal software ········································································7-1 7.1.1 Installing terminal software to PC ······························································7-2 7.1.2 Uninstalling PC terminal software ·····························································7-4 7.2 Installing VMS PC terminal software································································7-6 7.2.1 Installing VSM PC terminal software ·························································7-7 7.2.2 Uninstalling VMS PC terminal software ·····················································7-9 7.3 Setting up PC terminal and VMS PC terminal ··············································· 7-11 7.3.1 Setting up PC terminal and VMS PC terminal ········································· 7-12 7.3.2 When the IP address of the Communication unit cannot be determined ···························· 7-14

Chapter 8. Maintenance 8.1 Status monitor ··································································································8-1 8.1.1 Status message·························································································8-2 1. Distress message area ···············································································8-2 2. Communication status area ········································································8-3 3. Login display area ······················································································8-5 4. Area for displaying position ·········································································8-6 5. Message window display ············································································8-6 6. CAUTION Window······················································································8-7 8.1.2 Items displayed on the Status monitor ···················································· 8-13 Analysis of NG display ················································································ 8-14

iv CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Contents

8.2 [Option] -> 8. Test ·························································································· 8-18 8.2.1 PV (Performance Verification) TEST ······················································· 8-18 1. PV test sequence ····················································································· 8-18 2. Executing the PV test ··············································································· 8-18 3. Checking PV test result ············································································ 8-19 8.2.2 Diagnostic Test ························································································ 8-21 1. Diagnostic Test display area ·····································································8-22 2. REMOTE BOX display area ····································································· 8-22 3. MAIN STATE display area ········································································8-23 4. STATUS display area ··············································································· 8-24 8.2.3 Distress Button Test (Distress/SSAS Button Test) ··································· 8-25 1. Distress Button Test·················································································· 8-25 2. SSAS Button Test ····················································································· 8-25 8.3 [Options] -> 9.Maintenance (checking Log) ··················································· 8-26 8.3.1 "1. Current Position Log" ········································································· 8-26 8.3.2 "2. System Log"······················································································· 8-29 8.3.3 "3. Term Operation Log" ·········································································· 8-31 8.3.4 "4. Sent Report Log" ··············································································· 8-33 8.3.5 "5. Communication Log" ·········································································· 8-36 8.4 [Options] -> 7. LES Information ·····································································8-39 1. LES ID·········································································································· 8-39 2. Name ··········································································································· 8-39 3. Status ··········································································································· 8-39 4. Services ·······································································································8-40 5. TDM ch ········································································································ 8-40 8.5 Setting of DIP switches ·················································································· 8-41 8.6 Export/Import ·································································································8-42 1. Export··········································································································· 8-45 2. Creating directory and storing data ······························································8-46 3. Import ···········································································································8-48 8.7 Clearing memory ··························································································· 8-49 8.8 Command operation ······················································································ 8-50 8.9 Antenna unit Maintenance ············································································· 8-52

v CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Contents

Chapter 9. Q&A Q1. Is it possible to cut the Antenna coaxial cable? ···············································9-1 Q2. Is there compatibility of Antenna unit between IC-118 and IC-119? ················9-1 Q3. Is there any guideline for compatibility between Antennas?····························9-1 Q4. Are there cautions for replacing the board? ····················································9-1 Q5. Is there difference between FELCOM 18 and FELCOM 19? ··························9-1 Q6. Where can the program version are checked? ···············································9-1 Q7. The VMS PC Terminal program cannot be installed on PC.····························9-1 Q8. The program cannot be updated. ····································································9-1 Q9. Connection between PC terminal and Terminal unit cannot be established. ···9-2 Q10. How to re-register IMN ··················································································9-2 Q11. How to check transmission and reception ·····················································9-2 Q12. How to set IC-305, IC-306 and IC-307 ··························································9-2 Q13. What are special operations? ·······································································9-2 Q14. Is there any method to clear memory?··························································9-2 Q15. Is there any method to check whether SSAS is active? ································9-2 Q16. Is Version display of S/W displayed as the Diagnostic Test result?···············9-2 Q17. TX Power Supply and Current Level are not displayed on STATUS display for the result of Diagnostic Test. Is this failure?········9-2 Q18. Does the 5-digit number displayed on the System Log have meaning? ·······················································9-3 Q19. Where can the System Log be checked? ·····················································9-3 Q20. Is it possible to Export and Import SSAS setting? ·········································9-3 Q21. Is there setting of DIP SW?···········································································9-3 Q22. Is it possible to use a USB memory? ····························································9-3 Q23. Where does the SSAS unit: IC-307 need to be installed?·····························9-3 Q24. Why is the daisy chain connection used for connecting IC-307? ··················9-3 Q25. Why is the number of units connected to IC-307 limited to three units? ·············································9-3 Q26. Procedure for setting SSAS ··········································································9-4 Q27. What will happen if the system is turned ON while SSAS button is set to ON? ·····························································9-4 Q28. Since the password for entering SSAS Manager Mode is changed, the system cannot enter this mode. ··························································9-4 Q29. What are differences among Standard, USCG and Russia SSAS? ··············9-4 Q30. How to set VMS ····························································································9-4 Q31. How is LRIT set?···························································································9-5 Q32. Is it possible to operate both LRIT and VMS? ···············································9-5 Q33. Is there any method to check operating status of Data Reporting?···············9-5 Q34. What is the difference between Data Report and Message Report in [Reports] menu?·························································9-5 Q35. Is there any restriction on capacity of the SD card? ······································9-5 Q36. Where can DNID are checked? ····································································9-5

vi CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Contents

Q37. Is it possible to loop back the SSAS message? ············································9-5 Q38. Can the result of Diagnostic Test be stored on the SD card? ·······················9-5 Q39. The error message "EEPROM ERROR" appears. ········································9-6 Q40. Although IMN is set for FELCOM 18, IMN does not appear on the PC terminal. ·················································9-6 Q41. Can IC-315 and IC-318 on Junction Box use commonly? ····························9-6 Q42. Calculation of Frequency from Channel ························································9-6

Appendix 1. Event List

Appendix 2. Specifications

Electrical Parts List FELCOM 18 (IC-218) ····························································································· E-1 FELCOM 18 (IC-118)······························································································ E-2 FELCOM 19 (IC-219) ····························································································· E-3 FELCOM 19 (IC-119)······························································································ E-4

Drawings FELCOM 18 Interconnection Diagram: C5674-C01 ··············································· S-1 FELCOM 19 Interconnection Diagram: C5675-C01 ··············································· S-3 FELCOM 18 Schematic Diagram: C5674K01 ························································ S-2 FELCOM 19 Schematic Diagram: C5675K01 ························································ S-4

vii CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Summary Summary

Points to be checked ● No appears any Caution and Warning messages ● Is positioning data displayed properly? ● Is IMN registered? ● Is [Setup] -> System Setup Menu set? ● Is [Distress] menu set? ● Is it registered in ocean region? Login OK? ● Communication Test OK? ** PV Test, Receiving EGC, TELEX (useful method, by Loopback test for the message) ● Is SSAS set? And carried out SSAS Button Test OK? ● Is VMS set? ● Is LRIT working properly? ● Is S/W version checked?

1. FELCOM 18 drive A drive: Internal Memory (Flash Memory) C drive: SD card

2. Brightness adjustment of FELCOM 18 The brightness of the display can be adjusted at 11 levels. - [Alt] + [F6]: The display becomes darker. - [Alt] + [F7]: The display becomes brighter.

3. Connection of PC terminal When connecting PC terminal or VMS PC terminal via LAN, Network setting needs to be made on PC. For example, IP address: 172.31.16.10, Subnet Mask: 255.255.0.0, Default Gateway: N/A As for the IP address for the Terminal unit and Communication unit, the following address is set as default: 172.31.16.2/255.255.0.0 Note) Note that F18 (19) PC terminal software and VMS F18 (19) PC terminal software cannot be installed to the same PC.

1 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Summary

4. Updating the program The program is updated from the [LAN] port. As for FELCOM 18, the program can be updated from the SD card too. When updating the program by use of "Updater," the program file needs to be placed under (root) the C drive of the PC. For example, the program may not be updated if the program file is placed on desktop. When updating the program by use of "upf18term.bat," the program file can be placed at any position. As for checking S/W version, enter Furuno service mode, and then execute [Options] -> 8.Test -> 3.Diagnostic Test. Table 1. Program type

FELCOM 18 FELCOM 19

Program PC VMS PC Terminal/Comm. unit Terminal Terminal (For LAN) 3 3 3 3 3 3

Terminal/Comm. unit (For SD) 3 Non

5. Setting commands Enter a command on [Setup] -> 1.System Setup > Command Window. [Main Menu] 1. Remote Box Setup 2. External Alarm Setup Enter JOB No.: PASSWORD:

5.1 How to enter Service Mode JOB No. : furunoservice PASSWORD : felcom18 (felcom19) 5.2 How to enter SSAS Mode JOB No. : ssas manager PASSWORD: ship security alert (Common Password: wasuremashita+IMN) 5.3 How to change the SSAS Password JOB No. : ssas password

2 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Summary

5.4 How to cancel the SSAS transmission sequence JOB No. : ssas manager PASSWORD: ship security alert JOB No. : terminate ssas alert 5.5 How to exit from Furuno service mode and SSAS Mode JOB No. : quit -> Exiting from SSAS Mode or Furuno service mode JOB No. : quit service -> Exiting from Furuno service mode JOB No. : quit ssas -> Exiting from SSAS mode 5.6 ON/OFF setting for ALM Buzzer JOB No. : buzzer on, buzzer off 5.7 ON/OFF setting for LRIT Mode JOB No. : lrit on JOB No. : lrit off JOB No. : lrit Russia 5.8 Checking operation status of VMS Programming JOB No. : show prog JOB No. : slcainfo (EPADR Programming) 5.9 Monitoring NMEA data JOB No. : mon nmea (External GPS data) mon gps (Internal GPS data) 5.10 Resetting the setting to factory setting (All Clear: excluding FWD ID/RTN ID/Serial No.) JOB No. : furunoservice PASSWORD: felcom18 (felcom19) JOB No. : clr eeprom 5.11 Initialization of internal memory: A drive JOB No. : furunoservice PASSWORD: felcom18 (felcom19) JOB No. : clr intmem

3 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Summary

6. How to access to special setting 6.1 Re-registration of IMN, [Setup] -> 1.System Setup -> IMN Enter "IMN" while pressing and holding down [CTRL] and [ALT] keys. 6.2 Enabling and disabling DNID, [Report] -> 4.Data Network ID Password: data network id 6.3 Stopping SSAS (Standard Mode, Russia Mode) Repeating ON/OFF operation of the Alert button on IC-307 within three seconds 6.4 Password for accessing to VMS, [Report] -> 1.VMS Password: 123456789

7. Jumper setting 7.1 IC-305, 306 As for IC-305 and IC-306, "Remote Box Setup" needs to be set on Command Window as well as Jumper setting. Table 2. Jumper setting

JP1 JP2

IC-305: 16P0213A DISTRESS Short Short

RCV-1 Open Short

IC-306: 16P0213B RCV-2 Open Open

RCV-3 Short Open

7.2 IC-307 As for only IC-307 at the end, the JP-2 plug needs to be changed to JP-1. "Remote Box Setup" needs to be set on Command Window.

8. Transmit and receive test 8.1 Sending the message to the own ship This test is carried out in order to check whether message is properly received at the own ship by sending the message to the own ship. This test also checks whether the registered “IMN” is correct or not.

4 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Summary

Procedure) 1) Create an appropriate message at [File] -> 1: New. 2) Make the following setting in [Transmit] -> 1: Transmit Message. - Priority: Normal - Destination Type: TELEX - Country/Ocean Code: TELEX ocean region number POR: 582, IOR: 583, AOR-W: 584, AOR-E: 581 - Station ID: IMN of own ship - LES ID: Select LES. - Option -Confirmation: ON -Send Delay: 00:00 -Delivery Delay: Immediate -Code: IA5 3) Move the cursor to "Transmit" and then press [Enter] key. 4) Select "YES" and then press [Enter] key to start transmitting. 5) This test is OK if the same message is received after 5 to 10 minutes. 8.2 Loopback Test This is the Loopback Test for the message. Procedure) 1) Create an appropriate message at [File] -> 1: New. 2) Make the following setting in [Transmit] -> 1: Transmit Message. - Priority: Normal - Destination Type: Special - Destination: 91 - LES ID: Select LES. - Option -Confirmation: ON -Send Delay: 00:00 -Delivery Delay: Immediate -Code: IA5 3) Move the cursor to "Transmit" and then press [Enter] key. 4) Select "YES" and then press [Enter] key to start transmitting. 5) This test is OK if the same message is received after 5 to 10 minutes. Reference) If the message is not properly received, check "Delivery" at [Logs] -> 1.Sent Messages. The reason why the message cannot be received can be checked.

5 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Summary

9. Special operation of PP-510 - Turning the system on while pressing and holding down [LF]: All characters are printed. - Turning the system on while pressing and holding down [NLQ]: Printer settings are printed.

10. Replacing the board When replacing FELCOM 18: TERMCPU board (16P0283B) and FELCOM 19: COMMCPU board (16P0282), original EEPROM of these boards need to be used. Data, such as RWD ID/RTN ID/Serial No./DNID/ENID/SSAS/VMS, and System settings are stored on the EEPROM. Also, when these boards are replaced, all items need to be set again.

EEPROM EEPROM

FELCOM 18: TERM CPU(16P0283B)

FELCOM 19: COMM CPU(16P0282)

6 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Summary

Table 3. Action after replacing unit and board Unit/ board

FELCOM 18

FELCOM 19

Action

ANT UNIT

IC-118

IC-119

TERMINAL UNIT

IC-218

IC-306

Operation check Replacing EEPROM and resetting Replacing EEPROM and resetting Jumper setting

IC-305

Jumper setting

COMM. UNIT

IC-219

ALARM UNIT DIS/RCVED CALL UNIT SSAS ALERT UNIT JUNCTION BOX KEY BOARD

IC-307 IC-318 5139U

IC-307 IC-318

AC/DC PWR

PR-240

PR-240

Printer RF CON

PP-510 16P0284A

16P0284B

TERMCPU

16P0283B

COMMCPU TERMPWR COMMPWR PWR C SD USB SW LCD GPS Receiver

16P0282 16P0287B 16P0214A 16P0289 16P0294 3 16P0246 (GN-8097D)

16P0288 16P0277B

Incorporating in RF CON (GN-8097D)

SD card

Jumper setting Operation check Operation check Check the AC input power supply setting Operation check Operation check Replacing EEPROM and resetting Replacing EEPROM and resetting Operation check Operation check Operation check Operation check Operation check Operation check Operation check Formatting is required.

11. Cancelling Distress Alert The priority message (Priority: Distress) is sent to the appropriate RCC via the LES from which the Distress Alert was transmitted. Example of Canceling Distress Alert Message; NAME, CALLSIGN, ID NUMBER, POSITION Cancel my INMARSAT-C distress Alert of DATE, TIME UTC. =Master+

7 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Summary

Reference) Non-delivery notification failure codes ABS ACB ADR ANU ATD BK BUS CCD CI CIE CNS DTE ERR FAU FMT FSA IAB IAM IDS IDT IFR IMS IND INH INV ISR LDE LEF LPE MBB MCC MCF MKO MSO NA NAL NC NCH NDA NFA NIA NOB NOC NP NTC

Absent subscriber. The mobile terminal is not logged-in to the ocean region. Access barred. Addressee refuses to accept message. Deleted. The message has not been delivered within an hour and is therefore deleted. Attempting to deliver the message. Message aborted. Is used when a fax or PSTN-connection is cleared abnormally. Busy. Call cut or disconnected. Conversation impossible. The CES ran out of processing/communications capacity to process your message. Call not started. Data terminal equipment. Used when an X.25 subscriber has cleared the connection during the call attempt. Error. Faulty. Format error. Fast select acceptance not subscribed. Invalid answerback from destination. Was unable to process the address information in the following message: Invalid data from ship. Input data timeout Invalid facility request. Message size is invalid, 7932 characters maximum. Incompatible destination. Was unable to establish the type of message from following header. Invalid. Invalid ship request. Maximum acceptable message length or duration has been exceeded. Local equipment failure. Local procedure error. Message broken by higher priority. Message channel congestion. Message channel failure. Message killed by operator. Machine switched off. Correspondence with this subscriber is not admitted. No address line is present. No circuits. Subscriber’s number has been changed. There was no delivery attempt. No final answerback. No initial answerback. Not obtainable. No connection. No party. The called party is not, or is no longer, a subscriber. Network congestion.

8 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Summary

OAB OCC OOO PAD PRC PRF RCA REF RLE RPE RPO SCC SHE SNF SPE SUC TBY TGR TIM TMD UNK WFA WIA

Operator aborted. Subscriber is occupied. Out of order. Packet assembler/disassembler. Premature clearing. Protocol failure. Reverse changing acceptance not subscribed. There was a failure in the remote equipment. Resource limit exceeded. Remote procedure error. RPOA out of order. Call completed successfully. MES hardware error. The satellite network has failed. MES protocol error. Test results being delivered. Trunks busy. TDM group reset. Timeout. Too many destinations. Unknown. Is used when no other failure code are suitable. Wrong final answerback. Wrong initial answerback.

9 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Chapter 1. Overview 1.1 Overview 1.1 Overview 1.1.1 Overview FELCOM 18 and 19 are successors to FELCOM 15 and 16, and equipment configuration and operation are similar to those of FELCOM 15 and 16. Both equipments are compliant with SSAS, VMS and LRIT function. A setup of VMS is performed using VMS PC terminal. - VMS_FELCOM18_PC_V01.xx_Rxxxx - VMS_FELCOM19_PC_V01.xx_Rxxxx FELCOM 18 is successor to FELCOM 15 and Class-2 Inmarsat-C system for GMDSS ship. FELCOM 19 is successor to FELCOM 16 and Class-2 Mini-C system for Non-GMDSS ship. This equipment is installed in ships, such as pleasure boat, yacht and fishing boat, as Communication equipment. This equipment is also used as equipment for SSAS, VMS and LRIT function. Table 1.1.1 Comparison between FELCOM 18 and FELCOM 19 Item

FELCOM 18

FELCOM 19

EIRP G/T

12 to 16 dBW –23.0 dB/K 12 to 24VDC Power Supply (Tx: 8.0-4.0A, Rx: 1.0-0.5A) Antenna Unit IC-118: φ 156xH258 1.4 kg I C-218: 270H x 320W x 139D 4.0 kg Terminal Unit TLX terminal, Communication control (Communication Control part integrated type Unit) Connection with terminal PC (2nd DTE) is available. Printer PP-510, PP-520 (Centronics) IC-305: Distress Alert Distress Alert/Received Call Unit IC-350 (sharing connection with IC-305 Alarm Unit is not available.) Alarm Unit IC-306 SSAS Alert Unit IC-307: SSAS Alert Unit x 3set (Max) AC/DC Power Supply Unit PR-240 Junction Box IC-318: JUNCTION BOX [DTE] Port Not Used 10/100 Base-T [LAN] Port (for connection with terminal PC) [USB] Port Dedicated port for Key board [D-GPS] Port Available GPS INT: Option: GN-8097D, EXT External Connection SD card Memory

7 to 16 dBW -23.7 dB/K 12 to 24VDC (Tx: 3.8-1.9A, Rx: 0.8-0.4A) IC-119: φ 156xH258 1.4 kg (IC-219: 42H x 210W x 160D 1.2 kg) Connection with terminal PC is available. PC Printer None None None IC-307: SSAS Alert Unit x 3set (Max.) PR-240 IC-318: JUNCTION BOX None 10/100 Base-T (for connection with terminal PC) None None INT: Standard built-in (GN-8097D), EXT None

1-1 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

1.1 Overview

1.1.2 Configuration ADE and BDE are connected by use of the coaxial cable. External units connection are connected via JUNCTION BOX.

IC-118 Antenna Unit

FURUNO

TNC 5D-FB-CV: 30m 8D-FB-CV: 50m 12D-SFA-CV: 100m

Co-x

TNC

12 - 24VDC 100 - 220VAC

ANT

PWR

LAN

IC-218

PR-240

PC/HUB

PRINTER

Terminal Unit

Backup 24VDC AC/DC Power 24VDC Supply Unit

PP-510 Printer

25pin D-sub JUNCTION

15pin D-sub

TTYCSLA-4 or CO-0.2x5P

TTYCSLA-1 or O-0.2x2P

EPFS

LAN

RJ45

Max. 3 set IC-307

SSAS Alert Unit TTYCSLA-4 or CO-0.2x5P

IC-318

IC-307

SSAS Alert Unit

SSAS Alert Unit

IC-306

Junction Box

Alarm Contact Signal

IC-307

Alarm Unit TTYCSLA-4 or CO-0.2x5P

IC-305

or

Distress Alert/ Received Call Unit

IC-350

Alarm Unit

Fig. 1.1.1 Configuration Diagram of FELCOM 18

IC-119 FURUNO

Antenna Unit

TNC 5D-FB-CV: 30m 8D-FB-CV: 50m 12D-SFA-CV: 100m

Co-x

TNC PWR

12 - 24VDC

ANT

IC-219

LAN

Communication unit

LAN

RJ45

100 - 220VAC

15pin D-sub

PR-240 AC/DC Power Supply Unit

24VDC

2m TTYCSLA-1 or O-0.2x2P

IC-318 Alarm Contact Signal

PC/HUB

JUNCTION

Junction Box

TTYCSLA-4 or CO-0.2x5P

EPFS Max. 3 set

IC-307

SSAS Alert Unit

IC-307

SSAS Alert Unit

IC-307

SSAS Alert Unit

Fig. 1.1.2 Configuration Diagram of FELCOM 19

1-2 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

1.1 Overview

1.1.3 Overview of Connection Port 1. Connection of ADE and BDE IC-118/119 and IC-218/219 are connected by use of the coaxial cable. This coaxial cable includes 1.5 GHz receiving RF signal, 1.6 GHz transmitting RF signal, 1575.42 MHz receiving GPS RF signal and the power supplied to the Antenna unit. The transmitting voltage is +28 V (+27 V) and the receiving voltage is +7 V. The loss of the coaxial cable is estimated between 2 and 12 dB at 1.6 GHz band. Select the specified cable according to length. Since transmission excess input protection circuit (limiter) is built in the ANT RF circuit in the Antenna unit, it is possible to shorten the length of the specified cable.

-148 to -136dBW/m2

FELCOM 18: 12 to 16 dBw FELCOM 19: 7 to 16 dBw

ADE -> 8. Configuration -> 1.Station List

Same as "1. Data Report"

These menus need to be set when “Daily” is selected at “Activation”.

These menus need to be set when “Regular Interval” is selected at “Activation”.

2.2 Menu tree for FELCOM 18 terminal unit

4. Data Network ID

3. Enhanced Pre-Assigned Data Report(EPADR)

2. EPADR 2 3. EPADR 3 4. EPADR 4

1. EPADR 1

2. Message Report 3. Message Report 4. Message Report

File

Requested by

Activation (Regular Interval)

Destination

Report Length

2-9

Report Times MES

Interval Time

ON OFF Position Only Position and Course/Speed Position and Course/Speed and SEA INF DNID LES ID Member No.

Select File

Report Contents

Status

NAV NAV + SEA INF NAV(R) FILE

Enter times: 1 – 999 No Limit Enter 00:00 – 24:00 Enter 00:00 – 24:00 Enter 00:00 – 24:00

CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

F5: Reports

2. Message Report

1. Message Report

Start Time 1 Start Time 2 Start Time 3 Start Time 4

Report Times

15/30min, 1/2/3/4/6/8H (0001-7000)

Same as "1. EPADR 1"

This menu is fixed to “MES”.

Information of the “DNID” selected at “Destination” appears.

Same as "1. Message Report"

Available when “FILE” is selected at “Report Contents”

These menus need to be set when “Daily” is selected at “Activation”.

2.2 Menu tree for FELCOM 18 terminal unit

5. SSAS Report

6. Message Contents

2. SSAS Report 2 3. SSAS Report 3 4. SSAS Report 4 5. SSAS Report 5 Vessel Name MMSI IMN IMO Other Inf. LAT LON Time COURSE SPEED Time

Destination Type Prefix code Country/Ocean Code Destination Modem Type Address Subject LES ID Report Interval

2-10

max. 30 char. max. 9 digits max. 9 digits max. 9 digits max. 60 char. xx:xx.xxN(S) xxx:xx.xxE(W) mm/dd/yyyy/hh:mm:ss (UTC) xxx deg xx kn mm/dd/yyyy/hh:mm:ss (UTC)

00:00 – 99:59

SSAS ALART REPORT

Select Station

Remove ON TEST Real + Test Real Only Test Only

CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

F5: Reports

1. SSAS Report 1

Station Name

Mode

Status

[Report] menu in SSAS Manager Mode

Automatic input

Same as "1. SSAS Report"

Same as "F3: Transmit" Refer to 2-5 and 2-6.

Registration of Station List: F8: Setup -> 8. Configuration -> 1.Station List

2.2 Menu tree for FELCOM 18 terminal unit

LES ID/Name/Status/ Services/TDM ch.

Indian

Pacific

East-Atlantic

Yes No Yes No Yes No Yes No Yes No

2-11

CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

7. LES Information

6. Ocean Region

Auto

Cont’d

West-Atlantic

IOR

5. Select NCS

4. Abort

3. Log out

Yes No Yes No Yes No AOR (WEST) AOR (EAST) POR

LAT/LON/Update Time

1. Position

2. Log in

Select Transmitted Message Select Received Message Select EGC Message Display Communication Log

1. Send Messages 2. Receive Messages 3. EGC Messages 4. Communication Log

F7: Option

F6: Logs

NCS Channel List: ID, FREQ. AOR-W: 044/11080 AOR-E: 144/12580 POR: 244/12580 IOR: 344/10840

Input of Position: NMEA > Manual

2.2 Menu tree for FELCOM 18 terminal unit

Cont’d

1. System Setup

9. Maintenance

Enter IMN

IMN

EGC Output Port

Message Output Port

LAN Port

Nav Port

MES Operation Mode

Indication only

INMARSAT-C EGC OFF EXT INT AUTO ON OFF INT EXT INT+LAN AUTO INT LAN INT+LAN

No

Normal Mode 4.Distress Alert Button Test SSAS manager Mode 4. Distress/SSAS Button Test 1. Current Position Log 2. System Log 3. Term Operation Log 4. Sent Report Log 5. Communication Log System Date & Time Yes

Yes No Display Result Yes No

2-12

CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Cont’d

F8: Setup

F7: Option

8. Test

3.Diagnostics Test

2.PV Test Result

1.PV Test

Available when LAN port is "ON"

Re-enter) [ALT]+[Ctrl] -> “IMN”

Available when logging in “Service Mode”

Setting varies depending on “Normal Mode “and “SSAS Manager Mode”.

2.2 Menu tree for FELCOM 18 terminal unit

Cont’d

1. System Setup

Cont’d

JOB: furunoservice Password: felcom18

Command Window

1. Remote Box Setup

Mail Gateway

2-13

E: EXT

5. IC-306 No.3

4. IC-306 No.2

3. IC-306 No.1

2. IC-305

1.SSAS

Auto Delivery Keyword

Mail Address

Address Mode

Server IP

Delivery To

Attach

Gateway SMTP Enable IP Address Send Limit Size(KB)

DHCP: ON/OFF

CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Cont’d

F8: Setup

Network Setup

Network

IP Address Subnet Mask

1. OFF 2. IC-307 (Standard SSAS) 3. IC-307 (Russian SSAS) 4. SSAS (Momentary SW) 5. EXT ON OFF ON OFF ON OFF ON OFF

FIXED Auto

2, 4, 6, 8, 10, 16, 32 UUENCODE BINARY PC Mailer Server

172.31.16.2 255.255.0.0 ON OFF

Available when Server is selected at “Delivery To” and “Auto” is selected at “Address Mode”

Available when “Server” is selected at “Delivery To”

2.2 Menu tree for FELCOM 18 terminal unit

3. Terminal Setup

Window Color

Screen Saver

Date Disp. Form

Scroll

Cursor Type

Column Width

Tab Wide

Line No.

Word Wrap

Edit Mode

Text Mode

Command Window

2-14

CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Cont’d

F8: Setup

2. Editor Setup

1. System Setup

1. Distress Message 2. Distress EGC 2 External Alarm 3. Urgent EGC Setup 4. Unit Fault E: Exit Telex Ascii Insert Overwrite ON OFF ON OFF 2 Char 4 Char 8 Char 40 - 80 Block Underline Full Screen Half Screen YY – MM - DD MMM - DD - YY DD - MMM - YY ON OFF Select Preset 1, 2, 3 Yes Load Default No Window Fore Color Edit Color Back Color Brightness

Menus are toggled by using [] keys.

Column Width: Available when “Ascii” is selected in “Text Mode”

Available when the Edit window is closed

2.2 Menu tree for FELCOM 18 terminal unit

Cont’d

5. Auto Mode Setup

Auto Receive Message Save Auto Receive Message Print Data Report & Polling Print

Receive Alarm

Auto Communication Log Print

Coastal Warnings

ON OFF ON OFF ON OFF ON OFF ON OFF

Type of Message (Can’t reject other report)

2-15

QRU(no message)

Other navaid msg

SATNAV message

LORAN message

Pilot service

Meteo. forecasts

Ice Report

ON OFF A-Z

Enter area:max. 9

Enter one pos.

CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Cont’d

F8: Setup

4. EGC Setup

Receive EGC Area

Additional Position Navarea(s)/ Metarea(s) Fixed Area Waypoint(from NAV Equipment) Station Code ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF

2.2 Menu tree for FELCOM 18 terminal unit

Cont’d

8. Configuration

7. Directories

6. E-Mail Setup

3. EGC Channel List 4. NCS Channel List

2. LES List (Max. 44 stations x 4)

1. Station List (Max. 99 stations)

Select station Message Directory EGC Message Directory

Auto EGC Message Print

Station Group Station Name Destination Type Prefix code Country Code Station ID Modem Type Address Remark Name ID Remarks Max. 4ch x 4 Max. 20ch x 4

SatetyNET (Safety)

FleetNET

System

SafetyNET (Safety) SafetyNET (Urgent & Distress)

FleetNET

2-16

max 20 char. max. 15 char. Enter 3 digits max. 20 char.

ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF

CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Cont’d

F8: Setup

5. Auto Mode Setup

Auto EGC Message Save

System

Same as "F3: Transmit" Refer to 2-5 and 2-6.

Create Directory

LES used in “E-Mail” is selected.

2.2 Menu tree for FELCOM 18 terminal unit

8. Configuration

6. Export/Import

Import from SD

Export to SD

Attach File (MIME)

2-17

4. Settings

1. Station List 2. LES List 3. E-Mail/SMS Service List

9. Settings

OFF ON (BASE64) ON (UUENCODE) 1. Sent Message 2. Received Message 3. EGC Message 4. Station List 5. LES List 6. E-Mail/SMS Service List 7. Test 8. Maintenance

Enter LES ID Enter LES ID Enter LES ID Enter LES ID max. 9 char. max. 9 char. max. 9 char. max. 9 char.

max. 19 char. max. 9 char.

CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

F8: Setup

5.E-Mail/SMS Service List (Max. 16 stations)

Service LES Name Service ID(E-Mail) Service ID(SMS) LES ID (AORW) LES ID (AORE) LES ID (POR) LES ID (IOR) To: Cc: Subject: Separator SMS

The “SSAS setting file” can be imported in “SSAS Manager Mode”.

The “SSAS setting file” can be exported in “SSAS Manager Mode”.

2.2 Menu tree for FELCOM 18 terminal unit

Course Speed

Nature

Maritime Undesignated Fire/Explosion Flooding Collision Grounding Listing Sinking Disabled & Adrift Abandoning ship Further assistance required Piracy or Armed attack

Protocol

2-18

CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

F10: Stop Alarm

F9: Distress

LAT/LON

Position

LES ID Update Time

All Alarms are stopped.

The position needs to be updated every hour during manual input.

The position needs to be updated every hour during manual input. Fixed

2.2 Menu tree for FELCOM 18 terminal unit

F4: EGC

9. MIME (Decode) 1. Cut (DEL) 2. Copy (Alt + C) 3. Paste (INS) 4. Insert (with Citation) 5. Select All (Alt + A) 6. Search or Replace 7. Go to Line 8. Time or Pos. Ins. 9. Change Window (Alt + V) 1. Transmit Message 2. Cancel 3. Request Delivery Status 1. Display EGC Message 2. EGC Network ID

8. Print Setting

1. New (Alt + N) 2. Open(Alt + O) 3. Close (Alt + Q) 4. Save (Alt + S) 5. Delete (Alt + D) 6. Rename 7. Print (Alt + P)

Menu-1

Priority

Select file

Select file No Printer Windows Printer PP-510 Select file

Menu-2

Normal

Menu-3

2-19

Menu-4

CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

F3: Transmit

F2: Edit

F1: File

Function

2.3 FELCOM 19 Menu Tree

Menu-5

Same as FELCOM 18

Same as FELCOM 18

As for FELCOM 19, Distress is deleted.

Same as FELCOM 18

Disabled

Available while the Edit window is open

Remarks

Table 2.3.1 FELCOM 19 Menu Tree

2.3 FELCOM 19 Menu Tree

Cont’d

1. System Setup

System Date & Time IMN MES Operation Mode Nav Port LAN Port Message Output Port EGC Output Port

2-20

CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Note; F5: Reports In case of FxxPC terminal, "0.VMS Mode" is added to an F5:Report menu.

Cont’d

F8: Setup

F7: Option

F6: Logs

Note;

F5: Reports

1. Data Report 2. Message Report 3. Enhanced Pre-Assigned Data Report(EPADR) 4. Data Network ID 5. SSAS Report 1. Send Message Log 2. Receive Message Log 3. EGC Log 4. Communication Log 1. Position 2. Log in 3. Log out 4. Abort 5. Select NCS 6. Ocean Region 7. LES Information 8. Test 9. Maintenance

Disabled

Same as FELCOM 18

Note) 8.Test -> 4.SSAS Button Test

Same as FELCOM 18

Same as FELCOM 18

SSAS Report becomes available when entering “SSAS Manager Mode”. See page 2-10 for SSAS menu.

Same as FELCOM 18

2.3 FELCOM 19 Menu Tree

5. Auto Mode Setup 6. E-Mail Setup 7. Directories 8. Configuration

4. EGC Setup

Coastal Warning

Receive EGC Area

Connection Date Disp. Form Screen Saver Window Color Additional Position Navarea(s)/ Metarea(s) Fixed Area Waypoint(from NAV Equipment)

1. Remote Box Setup

Command Window JOB: furunoservice Password: Felcom19

2-21

1.SSAS

CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

F10: Stop Alarm

F8: Setup

3. Terminal Setup

2. Editor Setup

1. System Setup

Network Mail Gateway

Network Setup

Same as FELCOM 18 Same as FELCOM 18 Same as FELCOM 18 Same as FELCOM 18 Same as FELCOM 18

Disabled

Same as FELCOM 18

Same as FELCOM 18

Same as FELCOM 18

Same as FELCOM 18

Same as FELCOM 18 Disabled

2.3 FELCOM 19 Menu Tree

BDE: FELCOM 18 Chapter 3. Parts3.1Location

3.1 BDE: FELCOM 18 320 mm

157 mm

270 mm

139 mm

320 mm

4.0 kg

Fig. 3.1.1 Terminal unit (IC-218) [JUNCTION] [DTE]: Not used

[PRINTER] D-GPS ANT

LAN

Power: 12 – 24 VDC (8.0 – 4.0 A)

GND

Fig. 3.1.2 Terminal unit, rear view (IC-218)

3-1 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

3.1 BDE: FELCOM 18

Fig. 3.1.3 Keyboard (5139U)

TERMCPU (16P0283B) TERMPWR (16P0287B)

RF_COM (16P0284A) GPS: Option (16P0246)

PWR_C (16P0214A)

SD_USB (16P0289)

Fig. 3.1.4 Terminal unit with case removed

3-2 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

3.1 BDE: FELCOM 18

S1: System Reset SW

J14: IQ MONI S3: CPU Reset SW

(Not mounted)

1: I MONI 2: GND 3: Q MONI

S2 S4 CR6 CR5 CR3 CR2 CR1 XU20: EEPROM

Fig. 3.1.5 Terminal unit with RF CON board removed

D-GPS Port

GN-8097D 16P0246

RF CON (16P0284A)

Fig. 3.1.6 RF CON (16P0284A) and GPS (16P0246)

3-3 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

3.1 BDE: FELCOM 18

Fig. 3.1.7 TERMCPU (16P0283B)

R54: 28 V ADJ. R18: 130 kHz ADJ.

Fig. 3.1.8 TERMPWR (160287B) and PWR C (16P0214A)

3-4 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

3.1 BDE: FELCOM 18

Fig. 3.1.9 SD USB (16P0289)

Fig. 3.1.10 SW (16P0294)

3-5 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

3.1 BDE: FELCOM 18

Fig. 3.1.11 Panel

Fig. 3.1.12 LCD

3-6 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

3.2 BDE: FELCOM 19

3.2 BDE: FELCOM 19 210 mm

160 mm

42 mm

1.2 kg

Fig. 3.2.1 Communication unit, front panel (IC-219)

[JUNCTION]

Fig. 3.2.2 Communication unit, rear panel (IC-219)

3-7 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

3.2 BDE: FELCOM 19

COMMCPU (16P0282) COMMPWR (16P0288) GPS: GN-8097D

S2

S1: SYS Reset

S3

Fig. 3.2.3 Communication unit with case removed

CR12: Power CR11: LOGIN CR10: TX CR9: ERROR

U7: EEPROM

Fig. 3.2.4 COMMCPU (side A)

3-8 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

3.2 BDE: FELCOM 19

RF CON (16P0284B)

Fig. 3.2.5 Communication unit with COMMCPU board removed

Fig. 3.2.6 RF CON (16P0284B)

3-9 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

3.3 ADE

3.3 ADE

258 mm

1.4 kg 156 mm

Fig. 3.3.1 Antenna unit: IC-118 and IC-119

3-10 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

3.3 ADE

ANT RF FELCOM 18: 16P0285 FELCOM 19: 16P0286

Fig. 3.3.2 Dismounted view of Antenna unit

3-11 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

3.3 ADE

16P0286 (for IC-119)

16P0285 (for IC-118)

Fig. 3.3.3 ANT RF (16P0285, 16P0286)

3-12 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

3.4 Other unit

3.4 Other unit 3.4.1 JUNCTION BOX: IC-318

2m

137 mm H=43 mm

160 mm

IC-305 IC-306

NAV

DMC IC-307

1. Vcc 2. GND 3. TD/RD-A 4. TD/RD-B 5. N.C 6. ALM-H 7. ALM-C 8. RD-A(NAV) 9. RD-B(NAV) 10. GND 11. SSAS OUT-H 12. SSAS OUT-C 13. SSAS IN-H 14. SSAS IN-C 15. SSAS CTR

#11-15: #6-7: DMC -> SSAS TD -> ALM

3-13 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

3.4 Other unit

3.4.2 DISTRESS ALERT/RECEIVED CALL UNIT: IC-305 100 mm

120 mm

H=26 mm

JP1: short JP2: short 16P0213A

See Page 3-16. S1

S3

S2

3-14 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

3.4 Other unit

3.4.3 ALARM UNIT: IC-306 100 mm

120 mm

H=26 mm

JP1 JP2 See Page 3-16. 16P0213B S1

S3

S2

3-15 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

3.4 Other unit

Reference) Setting of JP1 and JP2 in IC-305 and IC-306 16P0213 board has type A and type B. It differs from the jumper setting of JP1 and JP2 and the presence of push button switches: S1, S2 and S3. Normally, a maximum of two units of IC-306 can be connected. One more unit can be equipped if requested. Table 3.4.1 Distinction between IC-305 and IC-306

JP1 JP2 S1: Distress S2: Alarm Ack S3: Alarm Reset

IC-305 16P0213 A DIS unit Short Short Yes Yes No

ALM unit-1 Open Short No No Yes

IC-306 16P0213 B ALM unit -2 Short Open No No Yes

ALM unit -3 Open Open No No Yes

3-16 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

3.4 Other unit

3.4.4 SSAS ALERT UNIT: IC-307

100 mm

120 mm

H=26 mm

Factory-default JP1: Open JP2: Jumper IC-307 setting at terminal JP1: Jumper JP2: Open

16P0229

3-17 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Chapter 4. System4.1 Setup Setup Menu 4.1 Setup Menu 4.1.1 System Setup 1. FELCOM 18 Set "[Setup] -> 1.System Setup" menu. Table 4.1.1 Settings of FELCOM 18 System Setup Item

Setting value

System Date & Time

YY-MM-DD

IMN

4xxxxxxxx

MES Operation Mode

INMARSAT-C EGC OFF EXT INT

Nav Port AUTO ON LAN Port

Message Output Port

OFF INT LAN INT+LAN AUTO

EGC Output Port Network Setup

Command Window

INT LAN INT+LAN Network Mail Gateway

Remarks The time data is calculated from the reception frame signal, and the date uses the data from ZDA. If there is no ZDA, the input date (Setup -> System setup -> System Date & Time) is used. To change IMN, type "IMN" while holding [Ctrl] and [Alt]. The input IMN is displayed on the status display. Normally, set to "INMARSAT-C." When set to INMARSAT C, Tx/Rx and the EGC reception are available. When set to EGC, only EGC reception is available. - OFF: Manually inputs the position of the own ship. Note) Note that the alarm is outputted when the data is not updated every 4 hours. - EXT: Uses the external GPS data. - INT: Uses the built-in GPS data. - AUTO: Automatically switches from INT to EXT. Note) As for SSAS Russia and LRIT Russia, NAV port is fixed to AUTO and GLONASS is preferentially used. This is ON/OFF setting for the LAN port. If set to "OFF," the error message "No response from communication unit" appears and transmission cannot be carried out when [Transmit] operation is carried out at the PC terminal. If the aforementioned "LAN Port" is set to "OFF" at the destination of the received message, LAN and INT+LAN are deleted. - INT: Outputs to the Terminal unit. - LAN: Outputs to the LAN port. - INT+LAN: Outputs to the Terminal unit and LAN port. - AUTO: Outputs to the ports according to Sub Address. (Terminal unit side (LAN): 000, DTE side: Fixed at 001) This setting is valid if the aforementioned "LAN Port" is set to ON at the destination of EGC received message. - INT: Outputs to the Terminal unit - INT+LAN: Outputs to the Terminal unit and LAN port. See the next page. This is the command for the direct access to TERMCPU board and this command is used to configure settings relevant to IC-305, IC-306, IC-307 and SSAS in Furuno service mode. ** Furuno service mode: Job No.: furunoservice, Password: felcom18

4-1 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.1 Setup Menu

Table 4.1.2 Settings of FELCOM 18 Networks Item IP Address Subnet Mask

Setting value

Remarks

172.31.16.2 255.255.0.0

Network of FELCOM 18 is set. The left is the default value. This setting is selected when the DHCP server is not connected or when no IP address is obtained from the DHCP server. This setting is selected when obtaining an IP address from the DHCP server. Enter the IP address of Default Gateway while connected to a different Network. Specify the IP address of the PC which is used to E-mail. A PC not specified cannot send E-mail but it can receive E-mail. Specify the size of the Mail to be sent: 2, 4, 6, 8, 10, 16, 32 KB Normally, UUENCODE is set when specifying the attachment format. The received message is delivered to the PC. The received message is forwarded to the Mail server.

OFF

Network

DHCP ON Gateway

. .

.

SMTP Enable IP Address

. .

.

Send Limit Size(KB)

8

Attach

UUENCODE BINARY PC Mailer

Mail Gateway

Delivery To Server Server IP

.

.

. The Mail server delivers mails to the specified "Mail Address." If the keyword registered by “Mail Address Keyword” is found in the text of a message, the message is sent to the Mail address which appears after the keyword. Specify the mail address to which mails are delivered. Enter the keyword to be searched while Auto is selected in Address Mode setting.

FIXED Address Mode Auto Mail Address Auto Delivery Keyword

4-2 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.1 Setup Menu

2. FELCOM 19 Set "Setup -> 1.System Setup menu".

Table 4.1.3 Settings of FELCOM 19 System Setup Item

Setting value

System Date & Time

YY-MM-DD

IMN

4xxxxxxxx INMARSAT-C

MES Operation Mode

EGC

Nav Port

INT/AUTO

LAN Port

ON

Message Output Port EGC Output Port Network Setup Command Window

INT INT Network Mail Gateway

Remarks The time data is calculated from the reception frame signal, and the date data (Setup -> System setup -> System Date & Time) uses the data from ZDA. If there is no ZDA, the input date is used. To change IMN, type "IMN" while holding [Ctrl] and [Alt]. The input IMN is displayed on the status display. Normally, set to "INMARSAT-C." When set to INMARSAT C, Tx/Rx and the EGC reception are available. When set to EGC, only EGC reception is available. This item is fixed to INT and the setting cannot be changed. As for FELCOM 19, GPS is built in. Note) As for SSAS Russia and LRIT Russia, NAV port is fixed to AUTO and GLONASS is preferentially used. This item is fixed to ON and the setting cannot be changed. This item is fixed to INT and the setting cannot be changed. This item is fixed to INT and the setting cannot be changed. See the next page. This is the command for the direct access to COMMCPU and this command is used to configure settings relevant to IC-307 and SSAS in Furuno service mode. ** Furuno service mode: Job No.: furunoservice, Password: felcom18

4-3 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.1 Setup Menu

Table 4.1.4 Settings of FELCOM 19 Networks Item

Setting value

IP Address Subnet Mask

172.31.16.2 255.255.0.0

DHCP ON Gateway

. .

Network of FELCOM 19 is set. The left is the default value. This setting is selected when the DHCP server is not connected or when the IP address is not obtained from the DHCP server. This setting is selected when obtaining an IP address from the DHCP server. Enter the IP address of Default Gateway while connected to a different Network. This item cannot be set.

OFF

Network

Remarks

.

Mail Gateway

3. Handling of EXT Nav Data The following table shows the list of NAV data input from the JUNCTION BOX. The following data format is used: Start bit: 1 / Data bit: 8 / Parity bit: None / Stop bit: 1. As for Speed, 4800 bps or 38400 bps is automatically detected. NAV data is not output. Table 4.1.5 Input sentence list

** ** ** ** ** ** GN, GP, GL ** ** **

Minimum input cycle 1 sec 1 sec 1 sec 1 sec 1 sec 1 sec 10 sec 1 sec 1 sec 1 sec

BWC BWR DBT DTM GGA GLL GNS GSA MTW RMA

**

1 sec

RMB

** ** ** ** ** **

1 sec 1 sec 1 sec 1 sec 1 sec 1 sec

RMC VDO VDR VTG WPL ZDA

Talker

Formatter Bearing and distance to waypoint Bearing and distance to waypoint – rhumb line Depth Below Transducer Datum Reference Global Positioning System Fix Data Geographic Position GNSS Fix Data GNSS DOP and Active Satellites Water Temperature Recommended Minimum Specific Loran-C Data Recommended Minimum Specific Navigation Information Recommended Minimum Specific GNSS Data UAIS VHF Data-link Own-vessel report Set and Drift Course over ground and ground speed Waypoint location Time and date

4-4 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.1 Setup Menu

Handling of checksum field If checksum is added, sum check is carried out. If there is an error, the sentence is disabled. If there is no checksum, the sentence is valid. Handling of timeout If valid data relevant to the Heading data is not received for 5 seconds or other valid data is not received for 30 seconds, timeout handling is carried out. Priority sequence Priority sequence of talker and formatter in data contents is as follows: formatter > talker. Priority sequence of the talker is GN > GP > GA > GL > LC > DE > LA > TR > IN > RA > WI > II > others." Data contents Positioning mode Latitude/longitude Latitude/longitude of destination Absolute vessel speed (ground) COG (Course over ground) Water depth (depth below transducer) Water temperature Time and time difference

Priority sequence GSA>GGA (assumed on the basis the number of satellites) GNS>GGA>RMC>RMA>GLL >VDO RMB>BWC>BWR>(WPL)

GN>GP>GA>GL>LC>DE>LA>TR> IN>RA>WI>II>Others

VTG>RMC>RMA>VDO VTG>RMC>RMA>VDO DBT

SD>YX>VW>VD>YC>Others

MTW

SD>YX>VW>VD>YC>Others ZA>GN>GP>GA>GL>ZC>ZQ>ZV> Others

ZDA>RMC

Set and Drift

VDR Current direction: VDR(T)>VDR(M)

Number of satellites in use

GSA

Note) - At Russia SSAS - VMS

Remarks

GN>GP>GA>GL>LC>DE>LA>TR> IN>RA>WI>II>Others

: EXT, "GL" talker has higher priority. : Depending on VMS setting file

4-5 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.1 Setup Menu

4. Handling of INT Nav Data The following table shows sentences that are input into and output from the GPS Module. The following data format is used: Start bit: 1 / Data bit: 8 / Parity bit: None / Stop bit: 1. Sentences output from the GPS Module Talker

Formatter

PFEC

Minimum input cycle

GP

GSA

―

10 sec

GP P P

ZDA FEC FEC

― GPenc GPtst

1 sec 1 sec 1 sec

Remarks Information of satellite in use Current time Encrypted NAV data GPS Self test Result

Sentences input into the GPS Module Talker

Formatter

PFEC

Minimum input cycle

P

FEC

GPclr

―

P

FEC

GPint

―

Remarks Start time and time when the port is set to be used

Priority sequence Data contents

Priority sequence

Positioning mode Latitude/longitude SOG(Speed over ground) COG (Course over ground) Current time and time difference Self Test Result Information of satellite in use

GSA > PFEC, GPenc PFEC, GPenc PFEC, GPenc PFEC, GPenc ZDA > PFEC, GPenc GPtst GSA

Talker

GP

4-6 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.1 Setup Menu

4.1.2 Outline of Command Window By operating Command Window in "Setup -> System setup," 1) Enter Furuno service mode and set ON/OFF for SSAS(IC-307), Distress Alert unit (IC-305) and Alarm unit (IC-306) by use of Remote Box Setup. 2) Enter Furuno service mode and then set ON/OFF of alarm contact output to ALARM System upon receipt of Distress message and Urgency message by use of External Alarm Setup. 3) Set ON/OFF of LRIT by typing the ON/OFF command for LRIT in JOB No. 4) Carry out maintenance by typing monitor, clearing memory and debug commands in JOB No. Reference) See page 8-50 for Command List.

How to enter Service Mode Procedure) 1. Open "Command Window" in [Setup] -> 1.System Setup. [Main Menu] 1. Remote Box Setup 2. External Alarm Setup Enter JOB No.:

2. Type "furunoservice" in Enter JOB No. 3. Enter password. Model name is used for the password. Only the cursor moves even if the password is entered. No character appears. - For FELCOM 18 -> felcom18 - For FELCOM 19 -> felcom19 [Main Menu] 1. Remote Box Setup 2. External Alarm Setup Enter JOB No.: furunoservice □ PASSWORD:

4-7 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.1 Setup Menu

4. When entering Furuno service mode, Furuno Service Mode appears and flashes at the center of the top of the screen. Also, [Main Menu] in Command Window is reversed.

[ Main Menu ] 1. Remote Box Setup 2. External Alarm Setup Enter JOB No.:

5. Type the number to be set and then enter the setting menu. To exit from Furuno service mode, type "quit" or "quit service" in Command Window. Turning the system on and turning it on again is acceptable.

4-8 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.2 FELCOM 18: Setting IC-305 and IC-306

4.2 FELCOM 18: Setting IC-305 and IC-306 As for IC-306 (Alarm Unit), a maximum of three units (standard: two units) can be connected. As for IC-305 (Distress Alert/Received Call Unit), only one unit can be connected. Any unit is recognized by the jumper setting. Enter "1.Remote Box Setup" in Command Window in [Setup] -> 1. System Setup, and then set ON/OFF for each unit. Note) These units can be only connected to FELCOM 18. No unit can be connected to FELCOM 19.

4.2.1 Jumper setting The jumper setting of 16P0213 A type/ B type boards is required for recognition of IC-305 and IC-306. Boards need to be set according to the following table. Type A board is for the IC-305 unit and type B board is for the IC-306 unit. Each type is recognized by the jumper setting of JP1 and JP 2 and the presence of S1, S2 and S3. Table 4.2.1 Difference between 16P0213A and 16P0213B

JP1 JP2 S1 S2 S3

16P0213A type Distress Alert/Received Call Unit (IC-305) DISTRESS Short Short Yes Yes No

RCV-1 Open Short No No Yes

JP1:short JP2:short

16P0213A

S1 S3

16P0213B type Alarm Unit (IC-306) RCV-2 Short Open No No Yes

IC-305

JP1 JP2

16P0213B

S1

S2

RCV-3 Open Open No No Yes

S3

S2

IC-306

4-9 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.2 FELCOM 18: Setting IC-305 and IC-306

4.2.2 ON/OFF setting Procedure) 1. See page 4-7 and enter Furuno service mode. 2. Press [1] -> [Enter] to open "1.Remote Box Setup" menu. [ Main Menu ] 1. Remote Box Setup 2. External Alarm Setup Enter JOB No.:1 [ Remote Box Setup ] 1. SSAS OFF 2. IC-305 OFF 3. IC-306 No.1 OFF 4. IC-306 No.2 OFF 5. IC-306 No.3 OFF E: Exit Enter No.:

3. Enter the number of unit to be set, and then press [Enter]. For example, press [2] -> [Enter] to activate IC-305. ON/OFF menu for [IC-305] appears. Press [1] -> [Enter]. "2. IC-305" in the [Remote Box Setup] menu is changed to "ON."

[ Remote Box Setup ] 1. SSAS OFF 2. IC-305 OFF 3. IC-306 No.1 OFF 4. IC-306 No.2 OFF 5. IC-306 No.3 OFF E: Exit Enter No.:2

[ Remote Box Setup ] 1. SSAS OFF 2. IC-305 ON 3. IC-306 No.1 OFF 4. IC-306 No.2 OFF 5. IC-306 No.3 OFF E: Exit Enter No.:

[ IC-305 ] 1. ON 2. OFF E: Exit Enter No.:1

Reference) The Terminal unit sequentially carries out polling for connected unit for which ON is set and monitors the switch status. As for FELCOM 19, there is no setting for IC-305 and IC-306.

4-10 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.2 FELCOM 18: Setting IC-305 and IC-306

4.2.3 Testing IC-305 and IC-306 1. IC-305 Execute [Option] -> 8.Test -> 4.Distress Button Test and then enter "Distress Button Test" mode. Operations are as follows. The Distress alert is not released even if this test is carried out. If [DISTRESS] button is pressed and held down more than 4 seconds without entering "Distress Button Test" mode, the Distress alert is released.

When entering Distress Button Test mode, the message "INF: Distress Buttons entered into TEST MODE." appears. LED of [DISTRESS] button on the Terminal unit on IC-305 and the buzzer become active at intervals of 100 msec/2s. Then, when pressing [DISTRESS] button, when [DISTRESS] button on IC-305 is pressed, LED of [DISTRESS] button on IC-305 and the buzzer become active at intervals of 100 msec. If [DISTRESS] button is pressed and held down for a while, the message "INF: DISTRESS ALERT UNIT works correctly." appears.

4-11 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.3 FELCOM 18: Setting IC-350

2. IC-306 Press [ALARM RESET] button. While pressing and holding down [ALARM RESET] button, the buzzer is sounded continuously and LED lights.

4.3 FELCOM 18: Setting IC-350 When connecting IC-350, set IC-350 and enter "Remote Box Setup" in Command Window in [Setup] -> 1.System Setup, and then set ON/OFF for the unit. When setting ON for IC-350, set "ON" for IC-305. IC-350 and IC-305 cannot be connected simultaneously. Either IC-350 or IC-305 needs to be selected.

4.3.1 Setting IC-350 Dip switch: S101 on the PANEL board (05P0820) needs to be set. Set "OFF" when connecting corresponding equipment. All switches are set to OFF at the time of factory default. S101: DIP SW

Fig. 4.3.1 Positioning of DIP SW on PANEL board

4-12 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.3 FELCOM 18: Setting IC-350

Table 4.3.1 Dip switch setting table S101 Bit #1 #2 #3 #4 #5 #6 #7 #8

Equipment to be connected No.1 VHF No.2 VHF MF/HF No.1 INMARSAT No.2 INMARSAT NAVTEX NAVTEX SEL VERCHK

OFF

ON

ENABLE ENABLE ENABLE ENABLE ENABLE ENABLE N.C. (NX-700) OFF

DISABLE DISABLE DISABLE DISABLE DISABLE DISABLE N.O. (NX-500) ON

# No.1 to 6: Connected models are set to "OFF" and unconnected models are set to "ON." Reference) Table of setting for Dip Switch on PANEL board

(Set to OFF at the time of factory default)

4.3.2 ON/OFF setting for IC-350 (Command Window) IC-305 and IC-350 are the same. See "4.2.2 ON/OFF setting" and set "ON" for IC-305.

4-13 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.3 FELCOM 18: Setting IC-350

4.3.3 Testing IC-350 Items to be tested are almost the same as those for IC-305 explained in "4.2.3 Testing IC-305 and IC-306." Execute [Option] -> 8.Test -> 4.Distress Button Test. Operations are as follows. When entering Distress Button Test mode, the message "INF: Distress Buttons entered into TEST MODE." appears. LED of [DISTRESS] button on the Terminal unit and the buzzer become active at the intervals of 100 msec/2 sec. As for IC-350, there is no change. Then, if [DISTRESS] button is pressed, when [DISTRESS] button on IC-350 is pressed, LED of [DISTRESS] button on IC-350 and the buzzer become active at intervals of 0.5 s, and the message "INF: DISTRESS ALERT UNIT works correctly." appears if [DISTRESS] button is pressed and held down more than 4 seconds.

4-14 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.4 FELCOM 18, 19 External Alarm Setup

4.4 FELCOM 18, 19 External Alarm Setup This setting is used to set whether to output alarm contact to ALARM System when receiving the Distress message or Urgency message. Alarm output is normally closed and interlocked with alarm buzzer. Resistance is approximately 30 Ω while closed between ALM_H and ALM_C.

IC-318 TERMCPU(16P0283B) COMMCPU(16P0282)

3.3V

K1 TLP4176G_TP_F R190

ALM

Q1 2

JUNCTION

4 ALM_A

6

ALM_H

3 ALM_B

7

ALM_C

6 7

Normal Close

Fig. 4.4.1 External Alarm output circuit

Procedure) 1. See page 4-7 and enter Furuno service mode. 2. Press [2] -> [Enter] to open "2. External Alarm Setup" menu. [ Main Menu ] 1. Remote Box Setup 2. External Alarm Setup Enter JOB No.:2 [ External Alarm Setup ] 1. Distress Message 2. Distress EGC 3. Urgent EGC 4. Unit Fault E: Exit Enter No.:

ON ON ON OFF

3. Enter the number of item to be set, and then press [Enter]. For example, press [3] -> [Enter] to set “OFF” for Urgent EGC.

4-15 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.4 FELCOM 18, 19 External Alarm Setup

Table 4.4.1 External Alarm setup list Item 1. Distress Message 2. Distress EGC 3. Urgent EGC 4. Unit Fault

Contents This is ON/OFF setting for External alarm output when receiving the Distress message. This is ON/OFF setting for External alarm output when receiving the Distress EGC message. This is ON/OFF setting for External alarm when receiving the Urgent EGC message. This is ON/OFF setting of External alarm when equipment fails. See the following list for target "Unit Fault".

Reference) Target messages for which Unit Fault is output TROUBLE: RFCON CPU ROM NG. TROUBLE: RFCON CPU RAM NG. TROUBLE: RFCON CPU EEPROM NG. TROUBLE: Synthesizer UNLOCK. TROUBLE: ANT power voltage abnormality. TROUBLE: ALARM UNIT Fault. TROUBLE: DISTRESS ALERT UNIT Fault. TROUBLE: SSAS UNIT connection abnormality. TROUBLE: Carrier power level. TROUBLE: EEPROM ERROR. TROUBLE: Invalid MES ID, This equipment is defected. Please contact FURUNO.

4-16 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.5 FELCOM 18 and 19: Setting SSAS

4.5 FELCOM 18 and 19: Setting SSAS SSAS (Ship Security Alert System) is intended for transmitting a Security alert to "recipients specified " without being noticed by attackers when the ship is under attack by armed invader, such as pirates, terrorists, etc. If any ship Security alert system: IC-307 button is pressed, the SSAS function activates and the alert indicating that the ship is attacked is transmitted to predetermined recipients (a maximum of 5 recipients) while sending information, such as Ship name, MMSI number, IMN and Own ship position at the predetermined intervals. No audible or visual alarm is generated while the SSAS report is being transmitted in order to prevent detection by the invaders. As for SSAS security alert unit: IC-307, the unit must be activated from the bridge and at least one more another position. As for FELCOM 18 and FELCOM 19, a maximum of 3 sets of IC-307 can be connected. Also, backup power is supplied to the ship Security alert system by the Main power supply and Auxiliary power supply. Also, IC-307 is connected in daisy chain connection. As for setting, set jumper of IC-307, enter "1. Remote Box Setup" in Command Window in [Setup] -> 1. System Setup menu, and then set ON/OFF for SSAS.

Points for operation 1. In case of pressing the [Alert] button on IC-307, when the [Alert] button is pressed and held down for 30 seconds while using Standard Type, 3 seconds while using Russian Type and 0.7 seconds while USCG Type is used, transmission sequence of SSAS alarm starts. 1) Whether the sequence starts cannot be determined by the status display and panel LED, etc. However, when the SSAS transmission sequence starts, information, such as Current Channel, Current TDM and MES Status, changes in the same manner as the normal transmission status. Whether or not the SSAS transmission sequence has started cannot be recognized with the lighting status of lamp on the Communication unit of FELCOM 19. The lamp lights in the same manner as normal transmission. While transmitting the SSAS message, the [TX] lamp lights. 2) Communication information indicating whether the alert is transmitted (Successful sending, Delivery Status) is not displayed. Communication information is neither printed nor recorded in the log. 3) Even if the power is turned off, the equipment resumes the SSAS alert sequence when powered on again.

4-17 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.5 FELCOM 18 and 19: Setting SSAS

4) If Delivery Status is "Not Complete" or 30 minutes elapse without receiving Delivery Status, the alert is transmitted again after changing the LES of the ocean region where the terminal is logged into. If E-Mail is set for Destination Type, E-mail is transmitted to destinations from the top in the LES list in the corresponding ocean region registered at E-Mail Setup. If TELEX is set for Destination Type, TELEX is retransmitted from the top of LES in the LES Information list for the corresponding ocean region. 5) If transmission is unsuccessful, an alert is retransmitted after automatically changing LES in the same manner as the item 4). 2. How to cancel the transmission sequence Method-1) Standard Type, Russian Type Switch the "Alert" button OFF in SSAS Manager Mode. When the message "NF: SSAS UNIT activation has been canceled." appears, the transmission sequence has stopped. Method-2) Standard Type, Russian Type Change the status of the "Alert" button in the following manner within 3 seconds: "OFF → ON → OFF → ON →OFF". When the message "INF: SSAS UNIT activation has been canceled." appears, the transmission sequence has stopped. Method-3) Standard Type, Russian Type Enter SSAS Manger Mode, and then type "terminate ssas alert". When the message "Please return the SSAS button into OFF-STATE." appears, return the "Alert" button on IC-307 to the OFF status. When the message "INF: SSAS UNIT activation has been canceled." appears, the transmission sequence has stopped. Method-4) USCG type Enter SSAS Manger Mode, and then type "terminate ssas alert". When the message "INF: SSAS UNIT activation has been canceled." appears, the transmission sequence has stopped.

As for the display indicating cancellation of transmission for FELCOM 19, the aforementioned message is output if the PC terminal is connected. While no PC terminal is connected, if the [POWER] lamp on the Communication unit flashes for 30 seconds at intervals of 1 second, the SSAS transmission sequence has stopped.

4-18 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.5 FELCOM 18 and 19: Setting SSAS

4.5.1 Jumper Setting Only for the last IC-307 unit, the JP-2 plug is changed to JP-1. This setting is required to activate the “error detection function” for cable wiring. See page 4-29.

Only for the last unit, the JP-2 plug is changed to JP-1. Factory setting: JP-1: Open JP-2: Jumper

4-19 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.5 FELCOM 18 and 19: Setting SSAS

4.5.2 ON/OFF setting Procedure) 1. See page 4-7 and enter Furuno service mode. 2. Press [1] -> [Enter] to open "1.Remote Box Setup" menu. [ Main Menu ] 1. Remote Box Setup 2. External Alarm Setup Enter JOB No.:1 [ Remote Box Setup ] 1. SSAS OFF 2. IC-305 OFF 3. IC-306 No.1 OFF 4. IC-306 No.2 OFF 5. IC-306 No.3 OFF E: Exit Enter No.:

3. Press [1] -> [Enter]. When SSAS setting menu appears, select the corresponding SSAS function. See the following page for the SSAS function. For example, press [2] -> [Enter] to activate Standard SSAS. “1. SSAS” in the [Remote Box Setup] menu is changed to "IC-307(Standard SSAS)".

[ Remote Box Setup ] 1. SSAS OFF 2. IC-305 OFF 3. IC-306 No.1 OFF 4. IC-306 No.2 OFF 5. IC-306 No.3 OFF E: Exit Enter No.:2 [ SSAS ] 1. OFF 2. IC-307(Standard SSAS) 3. IC-307(Russian SSAS) 4. SSAS(Momentary) E: Exit Enter No.:1

[ Remote Box Setup ] 1. SSAS IC-307(Standard SSAS) 2. IC-305 OFF 3. IC-306 No.1 OFF 4. IC-306 No.2 OFF 5. IC-306 No.3 OFF E: Exit Enter No.:

4-20 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.5 FELCOM 18 and 19: Setting SSAS

Table 4.5.1 Outline of the SSAS function Setting IC-307(Standard SSAS)

IC-307(Russian SSAS)

SSAS(Momentary)

Outline The SSAS alert button is latch type and used for the standard SSAS function. Note that after a button is pushed, transmission sequence is started in 30 seconds. This is SSAS for Russian type. The SSAS alert button is latch type and its operation is Standard SSAS. Note that after a button is pushed, transmission sequence is started in 3 seconds. However, NAV port setting is fixed to AUTO. As for position data, external GLONASS has priority. If there is no external GPS unit, internal GPS is used. Also, the message format is different from that of Standard SSAS. This is SSAS for USCG type. The SSAS alert button is momentary type. Note that after a button is pushed, transmission sequence is started in 0.7 seconds.

4.5.3 SSAS mode The SSAS function has two operating modes. - Normal mode: The unit starts up in this mode. The unit is used in this mode. SSAS-related menus are not displayed. - SSAS Manager Mode: Entering the SSAS Manager password in Setup -> 1.System -> Command Window enables entry into SSAS Manager Mode. - JOB No.ssas manager - Password: ship security alert In this mode, SSAS message and transmission cycle can be set, and “SSAS alert button test” can be carried out for IC-307. While the unit is in SSAS Manager Mode, the indication SSAS Manager Mode (flashing) appears at the center of the top of the screen. To exit SSAS Manager Mode, input "quit" or "quit ssas" on Command Window. The unit enters Normal Mode when the unit is turned on again. Note) Password: The default password is “ship security alert”. The manager can change the password. See page 4-23 for how to change the password.

4-21 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.5 FELCOM 18 and 19: Setting SSAS

1. Entering SSAS Manager Mode Procedure) 1. Enter the following JOB No. and password in Setup -> 1.System -> Command Window. Entering SSAS Manager Mode is possible. Only the cursor moves even if the password is entered. No character appears. - JOB No. ssas manager - Password: ship security alert (Default Password) [ Main Menu ] 1. Remote Box Setup 2. External Alarm Setup Enter JOB No.: ssas manager PASSWORD: ■

Important) The manager can change the password. If you do not know the password, enter the common password: wasuremashita+IMN. IMN is the IMN number set at Setup -> System Setup. For example, if IMN is 443256789, type "wasuremashita+443256789." 2. When entering SSAS Manager Mode, the indication SSAS Manager Mode (flashing) appears at the center of the top of the screen.

Reference) In case of logging in both SSAS Manager Mode and Furuno Service Mode, SSAS Manager Mode+S appears at the center of the top of the screen.

4-22 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.5 FELCOM 18 and 19: Setting SSAS

Operations that can be executed in SSAS Manager Mode are - SSAS related setting - Alert button test for IC-307 - Cancellation of repeated transmission of SSAS. Table 4.5.2 Menu added to SSAS Manager Mode for FLECOM 18 and FELCOM 19 Main menu

Reports

Sub Menu-1

Remarks

1. Data Report 2. Message Report 3. Enhanced Pre-Assigned Data Report(EPADR) 4. Data Network ID

5. SSAS Report

Options

Sub menu-2

8. Test

1. SSAS Report 1 2. SSAS Report 2 3. SSAS Report 3 4. SSAS Report 4 5. SSAS Report 5 6. Message Contents 1. PV Test 2. PV Test Result 3. Diagnostic Test 4. Distress/SSAS

Button Test

4. SSAS Button Test

Addition

Added for FELCOM 18. Added for FELCOM 19.

2. Changing the password for entering SSAS Manager Mode Changing the password is the operation carried out by the manager. Procedure) 1. Open Setup -> 1.System -> Command Window, type "ssas password" on the Enter JOB No. field, and then press [Enter]. 2. The line for inputting "OLD PASSWORD" appears. 3. Input "ship security alert" (without the quotation marks), which is the password set at factory default. The line for inputting "NEW PASSWORD" appears. 4. Input a new password to be set, using at least six characters, and then press [Enter]. The line for inputting “RETYPE NEW PASSWORD” appears.

4-23 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.5 FELCOM 18 and 19: Setting SSAS

5. Type the new password again, and then press [Enter]. If the password is changed, the message "Password changed" appears. If a wrong password is entered, the message "Mismatch-Password unchanged" appears.

[ Main Menu ] 1. Remote Box Setup 2. External Alarm Setup Enter JOB No.: ssas password OLD PASSWORD: NEW PASSWORD: RETYPE NEW PASSWORD: Password changed.

6. Press [Esc] several times to close the menu.

Reference) If the password is already changed, type the new password and then press [Enter]. If you do not know the password, the common password: "wasuremashita+IMN" is available.

4-24 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.5 FELCOM 18 and 19: Setting SSAS

4.5.4 Editing the SSAS Report This setting is made in "SSAS Manager Mode." When the SSAS Alert button on IC-307 is pressed, the message containing contents set in [Reports] -> 5.SSAS Report ->Message Contents is sent to destinations via LES set in [Reports] -> 5.SSAS Report -> SSAS Report 1 to 5. When the Ocean region is changed, the report is sent using the same LES for the Ocean region.

1. Setting SSAS Report Procedure) 1. Open [Reports] -> 5.SSAS Report. A maximum of five destinations (SSAS Report 1 to 5) can be set. For example, open 1.SSAS Report 1. 2. Set destination and intervals at which the report is transmitted. 3. Press [Esc] key to open the [Update] screen. Select "Yes" to update data.

4-25 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.5 FELCOM 18 and 19: Setting SSAS

Table 4.5.3 SSAS Report Menu Item Status

Setting value

Contents

Remove ON

Contents of the open page are removed. SSAS report A test message is sent to destinations set on the page, which is being open. SSAS alert is sent to destinations (SSAS Report 1 to 5) set in this mode. Also, when testing the button of SSAS Alert unit, the SSAS alert test message is sent to destinations (SSAS Report 1 to 5) set in this mode. SSAS alert is sent to destinations (SSAS Report 1 to 5) set in this mode. When testing the button of SSAS Alert unit, the SSAS alert test message is sent to destinations (SSAS Report 1 to 5) set in this mode. Destination can be selected from the list registered in Setup -> 8.Configuration -> 1.Station List.

TEST

Real+Test Mode Real only Test only Station Name

Destination Type

TELEX/MES FAX E-Mail SMS PADN DNID Special (Prefixed)

Prefix Code

xx

Country/Ocean Code

xxxx

Destination Modem Type

xxxxxxxxxxxxx xx T30 V21 – V32 Other

Address Subject LES ID

--Ex; 203(KDDI)

Report Interval

00:10 – 99:59

Destination Type can be selected (generally, E-mail and SMS) Reference) When selecting Special and entering "91" for Destination, the Loop Back Test for the SSAS message can be carried out. This code needs to be entered if Prefixed is set for Destination Type. These codes need to be entered if TELEX/MES, FAX and PSDN are set for Destination Type. Destination needs to be entered if TELEX/MES, FAX, PSDN or DNID Special is set for Destination Type. Modem Type needs to be entered if FAX is set for Destination Type. ** Generally, T30 is set. Address needs to be entered if E-Mail or SMS is set for Destination Type. Invalid LES needs to be selected from the LES list. The interval for sending the report needs to be entered (the minimum time is 10 minutes.)

4-26 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.5 FELCOM 18 and 19: Setting SSAS

2. Setting Message Contents The message set here is sent to destinations set for "1. SSAS Report 1 to 5. SSAS Report 5." Procedure) 1. Open [Reports] -> 5.SSAS Report -> 6.Message Contents. 2. Enter Vessel Name, MMSI and IMN, respectively. As for [Other Inf.], appropriate message can be entered. This message can be edited as needed. For example, Company Security Officer name and Call sign can be entered in [Other Inf.]. A maximum of 180 characters can be entered.

[Other Inf.] Description of IMO number is recommended. Arbitrary message (180 chr.) can be edited as needed.

COURSE/SPEED/Time Course/speed and confirmed time (ZDA) (VTG/RMC/ZDA)

SSAS Message Contents Vessel Name MMSI IMN IMO Other Inf.

LAT : LON : Time : COURESE: SPEED : Time :

- Vessel Name: 30 characters : ______________________________ - MMSI: Maritime Mobile Service : ______________________________ : ________________ Identity : ________________ - IMN: Inmarsat Mobile Number :____________________________________ ____________________________________ ____________________________________ 34.44.46N 135.21.26E 06/21/2012 04:22:20 (UTC) 071 deg 0.0 kt 06/21/2012 04:22:20 (UTC)

LAT/LON/Time and positioning time (GGA/RMC/GLL/RMA)

3. Press [Esc] key to open the [Update] screen. Select "Yes" to update data.

4-27 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.5 FELCOM 18 and 19: Setting SSAS

4.5.5 Testing the Alert button on IC-307 Procedure) 1. Enter SSAS Manager Mode. 2. Execute [Option] -> 8.Test -> 4.Distress/SSAS Button Test. The message "INF: Distress/SSAS entered into TEST MODE." appears. As for FELCOM 19, the message "INF: SSAS Buttons entered into TEST MODE." appears. Note) 1) If the unit does not enter SSAS Manager Mode, the unit remains in "4.Distress Button Test" and the SSAS Alert button on IC-307 cannot be tested. 2) SSAS Alert button cannot be tested from the PC terminal of FELCOM 18. 3. Check that the message "INF: SSAS UNIT works correctly." appears when the Alert button on IC-307 is pressed. 4. If the button is switched ON for more than 30 seconds, the test message is sent to the

destination specified for the “Test only” and Real+Test” in Mode of SSAS Report 1 to 5 settings.

4-28 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.5 FELCOM 18 and 19: Setting SSAS

Reference) Checking wiring While the SSAS function is set to ON in Command Windows, wiring is judged to be OK if "+6.5 V" is detected at SSAS OUT H (+6.5 V) output. If "+6.5 V" is not detected, the error message [SSAS UNIT connection abnormality] appears. Therefore, the function for checking connection of IC-307 does not work if wiring is done in daisy chain connection and [JP1] on the terminal unit is not jumpered. Wiring of IC-307 can also be checked in [Options] -> 8.TEST -> 4.Distress/SSAS Alert Button test. FELCOM 18/19 IC-318

6.5V

SSAS-OUT H U24

SSAS-CHECK

IC-307

11

1

13

3

U26

JP1 JP2 U1

SSAS-IN C SSAS-CTRL

14 15

SSAS Alert Button

4 5

Q3 TERMCPU COMMCPU

IC-307 1 3

JP1 JP2 U1

SSAS Alert Button

4 5

IC-307 1

Last unit

3

JP1 JP2 U1

SSAS Alert Button

4 5

Fig. 4.5.1 IC-307 connection

4-29 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.5 FELCOM 18 and 19: Setting SSAS

4.5.6 Sending the Test message (executing test mode) This test is carried out to check whether the "Test Report" can be properly sent to the destination, which was set in SSAS Report setting menu. When carrying out this test, be sure to check that equipment is working properly in advance.

1. If FELCOM 18 or FELCOM 19 is connected with the PC terminal Procedure) 1. Enter SSAS Manager Mode. 2. Open [Report] -> 5.SSAS Report, and then select "SSAS Report" for the destination to which the test report is sent in order to open the SSAS Report setting menu. 3. Open [Status], select "TEST" and then press [Enter]. 4. Press [Esc] key to open the [Update] screen. Select "Yes" to update data. 5. The test report is sent. After sending the test report, [ON] is automatically set for [Status] in the SSAS Report menu. In this case, the message "Successful Sending message" appears on the Printer and the Screen. The following figure shows the example of the test report received via E-mail. 6. Inquire the recipient whether the test report is properly transmitted to the destination.

>From: [email protected] >Date: Thu, 21 Jun 2012 02:13:36 UTC >Subject: SSAS ALERT REPORT >To: [email protected] > > > !!!Test Call !!! is added. > !!!! Test Call !!!! >--- SSAS ALERT MESSAGE -->Vessel Name: furuno test >MMSI: 431990000 >IMN: 443199010 >this is test ssas message. >from furuno test >LAT: 35:00.00N >LON: 135:00.00E >Time: 06/21/2012 01:56:15(UTC) >COURSE: *** deg >SPEED: ** kt >Time: MM/DD/YYYY hh:mm:ss(UTC)

4-30 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.5 FELCOM 18 and 19: Setting SSAS

2. If PC terminal is not connected with FELCOM 19 2.1) SSAS Standard mode, Russian Mode Before carrying out the test, be sure to check that the destination specified for the “Test only” and Real+Test” in Mode of SSAS Report 1 to 5 settings menu. In Case of set to “Real”, SSAS Test message is not sent, and [ERROR] lamps flashing. Reference) This operation transition can be checked on the PC terminal screen. Procedure) 1. Turn off the Communication unit. 2. Press the Alert button on No.1 IC-307 to switch "ON" the button. 3. Turn on the Communication unit and then enter test mode.

Entering test mode ON → Power ON

4. After approximately 30 seconds, [POWER], [LOGIN] and [TX] lamps simultaneously start flashing at intervals of 1 second. If this operation starts, the Alert button function on No.1 IC-307 is working properly. If the button does not work due to improper wiring, the [ERROR] lamp flashes at intervals of 1 second and next operation does not start.

POWER, LOGIN and TX lamps flash simultaneously at intervals of 1 second.

Note) If transmission of SSAS report is not required, switch OFF the Alert button within 30 seconds and then turn off the unit. When 30 seconds elapse, the test report is sent.

4-31 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.5 FELCOM 18 and 19: Setting SSAS

5. If approximately 30 seconds elapse while [POWER], [LOGIN] and [TX] lamps are simultaneously flashing, transmission of the test report starts and [POWER], [LOGIN] and [TX] lamps start flashing at intervals of 0.4 seconds at the same time.

POWER, LOGIN and TX lamps flash at intervals of 0.4 seconds.

6. If transmission of the test message succeeds (Successful Sending), [POWER], [LOGIN] and [TX] lamps simultaneously start flashing at intervals of 1 second.

When transmission succeeds: POWER, LOGIN and TX lamps flash simultaneously at intervals of 1 second.

Note) If 60 minutes elapse in this mode, the unit automatically enters normal mode. However, security alert is not transmitted. 7. Press the Alert button on No.1 IC-307 to switch "OFF" the button. Note) If 10 seconds elapse whiles the Alert button is switched "ON" after transmitting the test report successfully, the [ERROR] lamp starts flashing at intervals of 2 seconds. The Alert button needs to be switched OFF. The [ERROR] lamp stops flashing. 8. The unit goes into "idle" state in test mode. While the test mode is set to "Idle" status, each lamp lights for 1 second in the order of [POWER] → [LOGIN] → [TX] and this operation is repeated.

Scan operation for each lamp is repeated in the order of [POWER] → [LOGIN] → [TX]

9. Turn off the Communication unit and then turn on the unit again to exit test mode.

4-32 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.5 FELCOM 18 and 19: Setting SSAS

2.2) USCG Mode Before carrying out the test, be sure to check that the destination specified for the “Test only” and Real+Test” in Mode of SSAS Report 1 to 5 settings. In Case of set to “Real”, SSAS Test message is not sent, and [ERROR] lamps flashing. Procedure) 1. Turn off the Communication unit. 2. Press the Alert button on No.1 IC-307. 3. Turn on the Communication unit and then enter test mode.

Entering test mode ON → Power ON

4. The unit goes into "idle" state in test mode. If test mode is set to idle state, each lamp lights for 1 second in the order of [POWER] -> [LOGIN] -> [TX], and this operation is repeated. 5. Switch OFF the Alert button once, and then press the Alert button again. After 4 seconds, transmission of the test report starts, and then [POWER], [LOGIN] and [TX] lamps simultaneously start flashing at intervals of 0.4 seconds. In this case, release the Alert button.

POWER, LOGIN and TX lamps flash at intervals of 0.4 seconds.

4-33 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.5 FELCOM 18 and 19: Setting SSAS

6. If transmission of the test report succeeds, each lamp lights for 1 second in the order of [POWER] -> [LOGIN] -> [TX], and this operation is repeated.

When transmission succeeds: POWER, LOGIN and TX lamps light every 1 second.

7. Turn off the Communication unit and turn on the unit again in order to exit test mode.

4-34 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.6 Data Report

4.6 Data Report 4.6.1 Overview 1. Overview Data Report is the service to send small amount of data, such as position data, course and speed, from MES: FELCOM 18, 19 to users on the ground. VMS (Vessel Monitoring System) and LRIT (Long-Range Identification and Tracking of ship) use this service. Polling is the service that enables users on the ground to send the Polling Command to specific ship, specific group in the specific ocean region (area). For example, the report is transmitted according to the Polling Command sent from the LES (provider), or the report is transmitted according to intervals and start time for transmitting the report programmed in MES. To carry out Data Report, an agreement needs to be made between a user on the ground and LES, which works as the provider, and DNID (Data Network ID; LES number) needs to be downloaded into MES.

Table 4.6.1 Polling command list Command type 00H 01H 02H 03H 04H 05H 06H 07H 08H 09H 0AH 0BH 0C - 3FH 40 - 7FH

Meaning

Polling Type

Send Unreserved Report as required in [Response] Program Reserved Data Reporting Initiate Reserved Data Reporting Stop Reserved Data Reporting Program Unreserved Data Reporting Initiate Unreserved Data Reporting Stop Unreserved Data Reporting Define Macro Encoded Message Macro Encoded Message Data Transmission Download DNID Delete DNID Reserved User defined

Any(Individual, Group, Area Polling) Individual Any(Individual, Group, Area Polling) Any(Individual, Group, Area Polling) Any(Individual, Group, Area Polling) Any(Individual, Group, Area Polling) Any(Individual, Group, Area Polling) Any(Individual, Group, Area Polling) Any(Individual, Group, Area Polling) Any(Individual, Group, Area Polling) Any(Individual, Group, Area Polling) Individual Any(Individual, Group, Area Polling)

For example, if the polling command "02H Initiate Reserved Data Reporting" is received, initiates Data Reporting according to programming of "01H Program Reserved Data Reporting."

4-35 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.6 Data Report

2. Types of Data Report protocols Data Report is classified into the following protocols. Even if the protocol of Data Report changes, contents to be report do not change. Table 4.6.2 Data Report protocols Data Report types DR

EDR

PADR

EPADR

Outline Unreserved Data Report; This is the simplest Data Report. Since there is no acknowledgment function, the Report may not be transmitted securely. Enhanced Data Report; The Report can be securely transmitted by using the acknowledgement function after transmitting the report. Pre-Assigned Data Report; This report is the report, which is programmed on the ground and needs to be transmitted at fixed transmission intervals and fixed time (time). Since there is no acknowledgment function in the same manner as DR, the report may not be transmitted securely. Enhanced Pre-Assigned Data Reporting; This report is the report, which is programmed on the ground and enables further control compared to PADR. This report needs to be transmitted at fixed transmission intervals and fixed time (time). The report can be securely transmitted by using the acknowledgement function after transmitting the report in the same way as EDR.

Acknowledgement function: This function is used to check the checksum at the receiving side in order to confirm that the report is securely transmitted. If there is abnormality in Check-Sum, the retransmission request is sent to MES.

3. Sharing VMS and LRIT Do not operate VMS and LRIT in the same equipment at the same time. For example, when the unit is turned ON or OFF, or when an event, such as blocking, occurs, the report is transmitted to all valid DNIDs (LRIT and VMS). Note) The above operation depends on the VMS setting file. This item is applied to "VMS DNID only". Definition of this item is that the report is only transmitted to the DNID dedicated for VMS when an event occurs. If "FALSE" (default value) is set, above functions are applied to all DNIDs. If "TRUE" is set, the report is transmitted to the DNID in which characters "VMS" are entered in the "Name" field for DNID. Whether to add characters "VMS" is decided by the provider.

4-36 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.6 Data Report

4. Data Report by operating menu There is a way to transmit the report by programming Destination and intervals with operations of FELCOM 18 and FELCOM 19 instead of transmitting the report by use of Polling Command. [Report] -> 1. Data Report -> 1. Data Report

to

4. Data Report: -> Enhanced Data Report -> Usual Data Report

[Report] -> 3. Enhanced Pre-Assigned Data Report (EPADR) -> 1. EPADR - 4. EPADR [Report] -> 2.Message Report is the Data Report using Message Channel. Data Report is transmitted in the same way as TELX and E-Mail. The above Report uses Signaling Channel; therefore the system is different. 5. Displaying Data Report If the program is downloaded after downloading DNID, "Running Report Program (POLL)" appears at the lower left of the Status screen. "Data Report" appears while transmitting the Data Report.

Note) Do not operate VMS and LRIT in the same equipment at the same time. For example, when the unit is turned ON or OFF, or when an event, such as blocking, occurs, the report is transmitted to all valid DNIDs (LRIT and VMS).

4-37 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.6 Data Report

4.6.2 Enabling/Disabling DNID DNID of VMS and LRIT, which is downloaded for transmitting the Data Report, can be enabled or disabled. However, applicability of DNID (enabled or disabled) is defined by the VMS setting file when VMS is set to "ON." For example, is defined in the FFA VMS file; therefore DNID cannot be disabled. Be sure to set VMS "OFF" when enabling or disabling DNID.

Procedure) 1. Open [Report] -> 4.Data Network ID.

2. Select the DNID to be enabled or disabled, and then press [ENTER] key. When the password entry screen appears, enter the password “data network id,” and then press [ENTER].

4-38 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.6 Data Report

3. When the screen for enabling or disabling the DNID appears, select the item to be set.

- Disable DNID is disabled. Data Report is not executed. Act display:- Enable DNID is enabled. If the setting is returned from Enable (24-hour) or Enable (Temporary stop) to "Enable," the transmission cycle is set to "6 hours" for the following transmission regardless of the transmission cycle specified by the Polling command. Act display: * - Enable (24-hour) As for report using the Polling Command, the transmission cycle is set to "24 hours" for the first and subsequent transmissions regardless of the transmission cycle specified by using the Polling command for Data Report. Act display: 24h - Enable (Temporary stop) Transmission is temporarily stopped. Act display: STP

4-39 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.6 Data Report

4.6.3 VMS setting Report setting needs to be defined according to operation requirements of VMS. For example, at FFA, whether to transmit the report when an event, turning ON/OFF the unit, Blocking, entry into or exit from the specified ocean region, occurs, and setting for hiding that the report is being transmitted needs to be made on the Status screen. The above VMS setting is made using the PC terminal for VMS. See "Chapter 7. PC Terminal" for how to install the following VMS PC terminal software and start up the software. - VMS_FELCOM18_PC_V01.0x_Rxxxx - VMS_FELCOM19_PC_V01.0x_Rxxxx Note that the PC terminal software for FELCOM 18 and 19 and VMS PC software cannot be installed on the same PC.

1. Setting VMS ON Procedure) 1. Double-click the "VMS_FxxPC" to start up the VMS PC terminal. 2. "0.VMS Mode" is added when opening the [Report] menu. Open "0.VMS Mode". 3. When the Password entry screen appears, enter the Password: 123456789.

Password: 123456789

4-40 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.6 Data Report

4. The VMS Mode screen appears. Set VMS function "ON" and then press [Enter] key.

VMS Function -> ON

5. Click "LOAD" and select the VMS file to be set (for example, "felcom_vmssettings_FFA.xml"). The path of the selected VMS setting file appears on the LOAD column. Press [Enter].

LOAD

4-41 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.6 Data Report

6. Parameters of the selected VMS setting file are reflected on the VMS SETTINGS screen. Select [Apply] on this screen and then click [Enter] key.

Select [Apply].

7. If the VMS function activates, the preset "VMS name" appears at the lower left of the Status screen. ex: FFA is active.

4-42 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.6 Data Report

2. Setting VMS OFF Procedure) 1. Double-click the "VMS_FxxPC" to start up the VMS PC terminal. 2. Open "0.VMS Mode" from [Report] menu. 3. When the password entry screen appears, enter the password: 123456789.

Password: 123456789

4. The VMS Mode screen appears. Set the VMS function "OFF" and then press [Enter].

5. Click [LOAD], select the VMS filer for VMS to be deleted or select any VMS setting file, and then press [Enter] key. The path of the selected VMS setting file appears on the LOAD column. For example, select "felcom_vmssettings_FFA.xml."

LOAD

4-43 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.6 Data Report

6. When the “CHANGE VMS SETTINGS” screen appears, select [Apply] and then press [Enter] key.

Select [Apply].

7. If the VMS function is set to "OFF," the VMS name that appears at lower left of the Status screen disappears.

The VSM name disappears.

4-44 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.6 Data Report

3. Checking the VMS setting When the VMS setting file is loaded, setting parameters are reflected on the VMS SETTINGS screen. Following is the "felcom_vmssetings_FFA.xml" setting file.

4-45 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.6 Data Report

4. Editing the VMS setting file (reference) Do not edit the VMS setting file without reason. Each VMS setting parameter meets the requirements of corresponding VMS. This section is provided to help you understand VMS. When changing the setting of VMS parameters, edit the “felcom_vmssetings_xxx.xml” file and then upload the file. The VMS setting file is in xml format. This file can be edited by using WordPad and TraPad, etc. Following is the example of contents of the "felcom_vmssetings_FFA(E-Form).xml" file. As for "", Seeing key= indicates the setting and it is fixed, and value="xxx" indicates the parameter. "True" indicates ON and "false" indicates OFF. Also, if value="" is used instead of value="xxx," the setting value does not appear. Also, the setting group is classified from "" to "." Example of contents of the "felcom_vmssetings_FFA(E-Form).xml" file

: Indicates xml format.



: Shows the comment. Indicates the start of the file.



Start of the General group

Start of the Report Contents group

End of the Report Contents group

/: End of the Report Contents group Start of the Scan-Enable Ocean Region group

/: End of the Scan-Enable Ocean Region group Start of the Current Position Log group

4-46 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.6 Data Report

End of the Current Position Log group Start of the Event Report group End of the Event Report group Start of the Reduced Reporting group Start of the EnterCondition group End of the EnterCondition group Start of the LeaveCondition group End of the LeaveCondition group End of the Reduced Reporting group Indicates the end of file.

4-47 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.6 Data Report

As for the parameter to be changed, for example, in case of "," the part [value="false"] is changed. “False” indicates “OFF” and “True” indicates “ON”. As for setting other than ON/OFF, see "Setting" in the following table. Although the name can be changed, do not change the extension. Table 4.6.3 Meaning of VMS parameters Item

Setting

Meaning

Current VMS Feature

True/False

Allow EXT Nav Data

True/False

Preferred NAV Data Source

GPS GLONASS GNSS

Disable Logout

True/False

VMS DNID only

True/False

Forbid DNID Inhibit

True/False

Hidden VMS

True/False

EFORM

True/False

Enabling/Disabling the VMS function - TRUE: VMS function is enabled. - FALSE: VMS function is disabled. Normally, manual input is used for VMS. - TRUE: Setting NavPort is available. - FALSE: Setting NavPort is not available. - GPS: Only internal GPS data is used (default). - GLONASS: Data input from the NAV port (talker GL) is used. - GNSS: Data input from the NAV port (regardless talker) is used. - TRUE: Logout connection state cannot be retained (automatic Login). - Logout connection state is retained while FALSE is set. Event Report, Reduced Reporting and Area Report Interval functions are only applied to DNID dedicated for VMS. OFF: If FALSE is set, the above function is applied to all DNIDs. If characters "VMS" are entered in the "Name" field for DNID registration, the DNID is recognized as the DNID dedicated for VMS. - TRUE: The Data Report is only transmitted to the DNID dedicated for VMS. - FALSE: The Data Report is transmitted to all DNIDs. - TRUE: DNID cannot be manually disabled. - FALSE: DNID can be manually disabled. Setting whether to display the transmission status on the Status screen, Sent Report Log and Communication Log - TRUE: Transmission status of Data Report is not displayed. - FALSE: Transmission status of Data Report is displayed. - TRUE: EFORM is available. - FALSE: EFORM is not available.

Report Contents Position

True/False

Course/Speed

True/False

Engine

True/False

- TRUE: The report containing Position information is transmitted. - FALSE: The report containing Position information is not transmitted. - TRUE: The report containing Course/Speed information is transmitted. - FALSE: The report containing Course/Speed information is not transmitted. Specification of NYK Engine +Position + Course/Speed

4-48 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.6 Data Report

Program Version

True/False

Satellite Information

True/False

Area entered

True/False

Area left

True/False

Report Retransmissions Scan-Enable Ocean Region

0 – 10

Current(auto-chg NCS)

True/False

AOR-E

True/False

AOR-W

True/False

IOR

True/False

POR

True/False

Russia KKCM/MRCM type - TRUE: The report containing Program Version information is transmitted. - FALSE: The report containing Program Version information is not transmitted. Russia KKCM/MRCM type - TRUE: The report containing satellite information is transmitted. - FALSE: The report containing satellite information is not transmitted. - TRUE: The report notifying entry into the area is transmitted. - FALSE: The report notifying entry into the area is not transmitted. - TRUE: The report that notifies leaving from the area is transmitted. - FALSE: The report that notifies leaving from the area is not transmitted. Setting number of retries for processing failed report

During scan process, - TRUE: Scanning Current NCS is made. - FALSE: Scanning Current NCS is not made. During scan process, - TRUE: Scanning AOR-E is made. - FALSE: Scanning AOR-E is not made. During scan process, - TRUE: Scanning AOR-W is made. - FALSE: Scanning AOR-W is not made. During scan process, - TRUE: Scanning IOR is made. - FALSE: Scanning IOR is not made. During scan process, - TRUE: Scanning POR is made. - FALSE: Scanning POR is not made.

Current Position Log Period

1-1440

Intervals for recording the log: 1 to 1440 minutes (default is 60 minutes.)

Event Report First Position Report

True/False

Last Position Report

True/False

Antenna Fail Report

True/False

Antenna Blocked Report

True/False

Report that is sent when the unit is turned ON - TRUE: First Position Report is transmitted. - FALSE: First Position Report is not transmitted. Report that is sent when the unit is turned OFF - TRUE: Last Position Report is transmitted. - FALSE: Last Position Report is not transmitted. The report that is transmitted when the antenna is removed - TRUE: Antenna Fail Report is transmitted. - FALSE: Antenna Fail Report is not transmitted. The report that is transmitted when signal from satellites is not detected - TRUE: Antenna Blocked Report is transmitted. - FALSE: Antenna Blocked Report is not transmitted.

4-49 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.6 Data Report

GPS Blocked Report

True/False

Stored Report

True/False

Enter Reduced Reporting Mode

True/False

Leave Reduced Reporting Mode

True/False

Leave Area Report

True/False

The report that is sent while GPS data is disabled - TRUE: GPS Blocked Report is transmitted. - FALSE: GPS Blocked Report is not transmitted. The report that is sent when transmission fails - TRUE: Stored Report is transmitted. - FALSE: Stored Report is not transmitted. Start of Reduced Reporting Mode - TRUE: Reduced Reporting Mode starts. - FALS: Enter Reduced Reporting Mode does not start. Leaving from Reduced Reporting Mode - TRUE: Leaves from Reduced Reporting Mode. - FALS: Does not leave Reduced Reporting Mode. - TRUE: The report that notifies leaving from the area is transmitted. - FALSE: The report that notifies leaving from the area is not transmitted.

Reduced Reporting Use

True/False

Interval

5-1440

Enter Condition distance

1-999

time

1-1440

Leave Condition distance

1-999

time

1-1440

- TRUE: Reduced Reporting function is enabled. - FALSE: Reduced Reporting function is disabled. Intervals (minutes) for transmitting the report in Reduced Reporting Mode Conditions for recognizing entry into the area are set. Reduced Reporting Mode is enabled according to conditions of distance (A) and Time (B). With this setting, conditions for entering Reduced Reporting are set. Whether to enter Reduced Mode is determined based on how many meters the ship moves in specified time. - If the ship moves only 1 meter in 1 minute (1 m/1 min): Moves to Enter Reduced Reporting Mode. - If the ship moves only 400 meters in 180 minutes (400 m/180 min): Moves to Enter Reduced Reporting Mode. - If the ship moves only 999 meters in 1440 minutes (999 m/1440 min): Moves to Enter Reduced Reporting Mode. Conditions for recognizing leaving from the area are set. Reduced Reporting Mode is enabled according to conditions of distance (A) and Time (B). With this setting, conditions for leaving Reduced Reporting are set. Whether to leave from Reduced Mode is determined based on how many meters the ship moves in specified time. - If the ship moves only 1 meter in 1 minute (1 m/1 min): Moves to Leave Reduced Reporting Mode. - If the ship moves only 400 meters in 180 minutes (400 m/180 min): Moves to Leave Reduced Reporting Mode. - If the ship moves only 999 meters in 1440 minutes (999 m/1440 min): Moves to Leave Reduced Reporting Mode.

4-50 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.6 Data Report

5. Setting E-FORM The E-FORM (Electronic form) function is “applicable to FFA VMS type FELCOM 19. ” E-FORM is the xml file, which is transmitted from FFA in the form of E-Mail via satellite circuit and downloaded into the VMS PC terminal connected to FELCOM 19. In this system, an FFA subscriber writes requirements in the specific downloaded file and sends the file to FFA via E-Mail. Restrictions on E-FORM 1) Maximum number of E-FORM programs A maximum of 20 different E-FORM programs need to be supported. 2) Version A maximum of 100 different E-FORM programs need to be supported. 3) Number of transmitted reports A maximum of 100 E-FORM reports need to be stored. If there are more than 101 reports, the old file is deleted. 4) Number of unsent messages A maximum of 100 E-FORM reports need to be stored. If there are more than 101 reports, the old file is deleted.

6. Activating E-FORM Key points) 1) Using VMS_F19 Terminal PC, as for E-FORM setting in the FFA VMS setting file, confirm that is set to "true." 2) Set the above FFA VMS "ON." 3) Using F19_PC Terminal PC of user, place “FelcomEForm.dll” and “FelcomEForm.exe” in the directory of the execution file for “VMS_F19PC”.

4-51 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.6 Data Report

Procedure) 1. Using VMS_F19 Terminal PC, set FFA VMS "ON." 2. Install F19_PC Terminal software to user PC, confirm that the F19PC.exe file is stored in the “C:¥Program Files¥Furuno ¥FELCOM19” folder, which is automatically created when F19PC is installed. 3. Paste E-FORM files (FelcomEForm.dll and FelcomEForm.exe) here.

Pasting FelcomEForm.dll and FelcomEForm.exe

4. When F19PC terminal software starts up, "4.E-FORM" is added to [Transmit] menu. 1. 2. 3. 4.

Transmit Transmit Message Cancel Request Delivery Status E-FORM

7. Opening E-FORM The E-FORM file is downloaded from FFA via satellite circuit and stored in the specific folder "original" for F19PC. Or, the E-FORM file can be pasted on this folder. If the E-FORM file is pasted on the specified folder by any of the methods, E-FORM becomes available. The location of the specified folder is as follows. C:¥ Documents and Settings ¥ installuser ¥ Application Data ¥ Furuno ¥ EFORMs ¥ original

4-52 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.6 Data Report

Reference) versiontest-10.10.efm This file is the E-FORM file, which is created when E-FORM is activated. The file form shown in the following figure is not "E-FORM" downloaded from FFA.

4-53 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.6 Data Report

4.6.4 ON/OFF setting for LRIT Mode If LRIT mode is set to ON, LRIT Report has priority over EGC reception. The priority of transmission of normal message and reception of LRIT message is the same. For example, since transmission of the LRIT Report starts at the time set for LRIT Report even while receiving EGC message, EGC reception is paused. Therefore, do not set LRIT Mode “ON” if FELCOM 18 is GMDSS compliant. If LRIT Mode is set to OFF, EGC reception is prioritized. Also, if LRIT Report protocol is programmed by use of EDR, attempts to retransmit the report are made a maximum of "5 times" if the LRIT Report is not properly transmitted while LRIT Mode is set to ON. If LRIT Mode is set to OFF, retransmission of the LRIT Report is not carried out. Regardless of ON/OFF setting of LRIT mode, if MES is in busy state by message reception or other reasons, the LRIT Report is suspended until status becomes ready. The standby time is 5 minutes. If busy condition continues for 5 minutes, data report is not transmitted at that time.

Note) Do not operate VMS and LRIT in the same equipment at the same time. For example, when the unit is turned ON or OFF, or when an event, such as blocking, occurs, the report is transmitted to all valid DNIDs (LRIT and VMS).

Procedure) To set up LRIT Mode, open [Setup] -> System -> Command Window, and then enter the following LRIT command in JOB No. - lrit on - lrit off - lrit Russia

: Standard LRIT Mode is set. : Standard/Russia LRIT are set to OFF. : Russia LRIT Mode is set.

4-54 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.6 Data Report

Setting Standard LRIT

Setting Russia LRIT

Standard LRIT ON As for external GPS sentences, enter ZDA, VTG, and RMC or GGA and GNS at the geodetic reference system (Datum) for WGS84. Russia LRIT ON [Setup] -> System Setup -> NAV Port preferentially uses GLONASS (talker: $GL). Contents to be reported are Position + Course Speed. As for external GPS sentences, enter ZDA, VTG, and RMC or GGA and GNS at the geodetic reference system (Datum) for WGS84.

4-55 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

4.6 Data Report

4.6.5 Checking the operation status of Program Report To check the operation status of the programmed LRIT and VMS, enter Furuno service mode from [Setup] -> 1.System Setup -> Command window, and then type "Show prog." As for Data Report using the EDADR protocol, type "slcainfo." Contents to be displayed and printed are basically the same even if Data Report varies depending on the protocol.

4-56 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Chapter 5. Block Description 5.1 Configuration 5.1 Configuration 5.1.1 Configuration of the board 1. FELCOM 18

IC-118 Antenna unit -90deg.

0deg.

ANT BASE (16P0279) J1

ANT RF (16P0285) TNC

J2 TP5FBAW-5DFB(30m) 8D-FB-CV(50m) 12D-SFA-CV(100m)

TNC

DGPS RF J7

IC-218 Terminal unit

ANT J1

28V / 7V

6.5V, 3.3V, HPA ON, CHECK V, ANT TX, ANT RX

J6

GPS (16P0246) J1 TD, RD, VBAK, VCC

JUNCTION J12

J13

J4

J3

J3 GPS Sig.

J5

J2

HPA ON, DET SIG, CHECK V, ANT TX, ANT RX, RF AGC CTRL, PLL CLK, PLL LD2, PLL LE2, PLL LD1, PLL LE1, PLL DATA, TX RX, TX DATA, IF AGC CTRL, TCXO CTRL, MCLK CODEC, 2nd IF Q, 2nd IF I

RF CON (16P0284A)

J2

J1

VCC, TD/RD-A/B, ALM-H/C, RD-A/B, SSAS OUT-H/C, SSAS-CHECK, SSAS IN-C, SSAS CTRL

15pin D-sub

DC(+) DC(-)

J1 J5

J10

J11 LCD CTRL, LCD PWM, 5V, 3.3V, 6.5V

TERMPWR (16P0287B)

RJ45

DTE J1

TERMCPU (16P0283B)

J7

RXD, TXD

PRT STB N, PRT D[0]-[7], PRT ACK N, PRT BUSY, PRT PE, PRT SEL, PRT ALF N, PRT ERR N, PRT INIT N, PRT SELIN N

J6 6.5V, BUZ, LED, SW

DC(-), SW(+), B(+)

J2

8V

J1

LAN

LEDA, LEDK

PWR C (16P0214A)

12 - 24VDC

J2

3.3V, CD, WP, SD DAT0-3, CLK, USB PWR EN, USB PWR FLG N, D(+), D(-), 5V

9pin D-sub Not Used

PRINTER 25pin D-sub

J6

J7

J5

3.3VLCD, INO+/-, IN1+/-, IN2+/-, CLK+/-

J1

SW (16P0294)

J1

LCD

J2

SD CARD

J3

SD USB (16P0289)

KEY BOARD

Fig. 5.1.1 Configuration of the board of FELCOM 18

5-1 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

5.1 Configuration

2. FELCOM 19 Fig. 5.1.2 Configuration of the board of FELCOM 19

5.1.2 Major functions of the board Table 5.1.1 Major functions of the board Board DAISY LOOP type antenna

ANT RF IC-118: 16P0285 IC-119: 16P0286

Function Directional characteristics - Horizontal: Non-directivity - Vertical: EL=90 deg -> 0 dBi and more EL= 5 deg -> +1.3 dBi and more - Polarization: Right circular polarization wave This antenna consists of TX/RX RF amplifier circuit and Duplexer, and TX and RX are switched by antenna supplied voltage: TX 28 V (27 V) / RX 7 V. Also, this antenna automatically stops the transmission when the temperature of the board is over +95 deg. - ANT RF RX input level: -141 to -129 dBm - ANT RF RX output level: -106.2 to-86.2 dBm - ANT RF TX input level: -2 to +13 dBm - ANT RF TX output: IC-118/42 dBm, IC-119/+39.5 dBm - Continuous transmission time: 15 minutes

Remarks

As for differences between IC-118 and IC-119, the transmit PA AMP and transmit output are different.

5-2 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

5.1 Configuration

RF CON IC-218 16P0284A IC-219 16P0284B

TERMCPU IC-218: 16P0283B

TERMPWR IC-218: 16P0287B

PWR C IC-218 (16P0214A) COMMCPU IC-219: 16P0282

COMMPWR IC-219: 16P0288

PWR C IC-219 (16P0227B) GPS Receiver

Receiving circuit: The RF signal from Antenna unit is changed to I signal and Q signal of 2nd IF 7.5 kHz and the signal is sent to the TERMCPU board. Transmit circuit: TX DATA in 600/1200 sps Base band that is changed to signals on the TERMCPU (COMMCPU) board is modulated at 1.6 GHz band/ BPSK and then output to the Antenna unit. This board is equipped with the function for processing transmit and receive signals, communication protocol control function and interface function. Also, this board outputs AGC, TCXO and PLL control signals to the RF CON board. As for the receive signal, I signal and Q signal of 2nd IF 7.5 kHz from RF CON board are input. As for the transmit signal, TX DATA (600/1200sps) of the Base band that are changed to signals is output to the RF CON board. Input voltage: This board is 12 to 24 V switching regulator and equipped with the circuit protecting from Low-input voltage, Over-voltage and Over-current. Output voltage are 28/7 V, 6.5 V, 5 V, 3.3 V, 8 V. 28/7 V is switched by the HPA ON signal at the antenna power supply. Detection of status monitor signal: - CHECK V: Antenna Power supply - TX ANT: Detection of current level at TX 28 V - RX ANT: Detection of current level at RX 7 V

As for status monitor display relevant to power supply, enter Furuno service mode and execute [Option] -> 8.Test -> 3.Diagnostic.

This board consists of the noise filter and the power reverse connection protector diode. This board has the same functions as the TERMCPU board of IC-218. However, SD-USB, Printer, Serial RS-232C, LCD, and a Buzzer function are removed. Input voltage: This board is 12 to 24 V switching regulator and equipped with the circuit protecting from Low-input voltage, Over-voltage and Over-current. Output voltage are 27/7 V, 6.5 V, 3.3 V. 27/7 V is switched by the HPA ON signal at the Antenna power supply. Detecting the following status monitor signal: - CHECK V: Antenna Power supply - TX ANT: Detection of current level at TX 27 V - RX ANT: Detection of current level at RX 7 V

As for status monitor display relevant to power supply, enter Furuno service mode and then execute [Option] -> 8.Test -> 3.Diagnostic.

This board is mounted with the Power connector. This board outputs GSA, ZDA, GPenc and GPtst. GPenc is encoded data.

5-3 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

5.2 ADE

5.2 ADE 5.2.1 Outline of Antenna unit The Antenna unit consists of ANT RF board, ANT B and the Bird cage-type antenna element. Since transmit output is different between FELCOM 18 and FELCOM 19, the ANT RF board is different. Table 5.2.1 Difference of Antenna unit Difference Antenna unit Board ANT RF output Transmit EIRP Supply voltage Transmit PA amplifier

FELCOM 18 IC-118 ANT RF(16P0285) Output of +41.0 to 43.0 dBm 12 to 16 dBW (Antenna elevation angle is 5 deg.) Tx 28 V / Rx 7 V (Tx: 2.8 A)

FELCOM 19 IC-119 ANT RF(16P0286) Output of +38.5 to 40.5 dBm 7 to 16 dBW (Antenna elevation angle is 5 deg.) Tx 27 V / Rx 7 V (Tx: 1.5 A)

BLF3G21_30

MRF6S20010GNR1

Compatibility of Antenna unit Although different antenna unit cannot be connected, a different Antenna unit can be temporarily connected according to the following table in order to check equipment and detect failures of Antenna or Communication unit. Also, when connecting other Antenna unit, the Antenna coaxial cable having the standard length for the equipment needs to be used. For example, when connecting Antenna unit: IC-115 of FELCOM 15 to FELCOM 18, IC-115 may break if the cable is shorter than the specified coaxial cable length. Table 5.2.2 Antenna unit combination ADE

Antenna to be connected FELCOM 19 FELCOM 15 (IC-119) (IC-115) OK OK

FELCOM 18

FELCOM 18 (IC-118) OK

FELCOM 19

NGNote1)

OK

NG Note1)

OK

FELCOM 15

NG Note2)

NG Note2)

OK

OK

FELCOM 16

Note1)

Note2)

BDE

NG

NG

NG

Note1)

FELCOM 16 (IC-116) OK

OK

Note1) There is a possibility that a PWR board may break. Note2) There is a possibility that a power may not be turned on.

5-4 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

5.2 ADE

5.2.2 Antenna element Antenna unit consists of the element, the 3 dB hybrid and the reflector. The Antenna unit is developed by FURUNO and called "DAISY LOOP ANT." The element has Bird cage-like shape. As for FELCOM 18, ANT RF output, 42 dBm of 1.6 GHz band is radiated from the Antenna by 14 dBW. As for FELCOM 19, +40 dBm is radiated from the Antenna by 9 dBW of EIRP Also, the receiving signal of the power flux density, -148 dBW/m2 to–136 dBW/m2 of 1.5 GHz band is output to the ANT RF receiving circuit with the level of–141 dBm to–129 dBm. - TX/RX antenna gain: more than 1.3 dBi (When the antenna elevation angle is +5°.) - Directional characteristics Horizontal: Non-directivity Vertical: 1.3 - 1.5sin (θ - 5) dBi (+5°< θ < +90°) -2.7 + 4cos [4.5 (θ - 5) ]dBi (-15°< θ < +5°) - Polarization: Right circular polarization wave

0 dig.

-90 deg.

ANT RF F18:16P0285 F19: 16P0286

50 ohm

3db Hybrid

Fig. 5.2.1 Outline of Antenna element

The following figure shows the vertical directivity of reception (transmission is similar) of FELCOM 18 and FELCOM 19. Horizontal directivity is approximately circular and has non-directivity.

1537.0 to 1544.2MHz

Fig. 5.2.2 Vertical directivity

5-5 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

5.2 ADE

5.2.3 ANT RF FELCOM 18(IC-118): 16P0285 FELCOM 19(IC-119): 16P0286 ANT RF board consists of the transmitting RF amplifier circuit, the receiving RF amplifier circuit, the receiving GPS amplifier circuit, the circuit for switching TX and RX, and the Heat protecting circuit. Also, Duplexer is installed at the input/output unit of TX/RX RF circuit at the Antenna side in order to divide TX/RX RF signal. Receiving circuit Receiving gain: 38.8 dB ± 4 dB NF=2.0 dB max. GPS: 34 dB ± 3 dB - ANT RF input signal (1537.0 to 1544.2MHz) level: - 141to - 129 dBm - ANT RF output signal level: - 106.2 to - 86.2 dBm - ANT RF input signal (1575.42 MHz) level of the GPS reception signal: - 130 dBm - ANT RF output signal level of the GPS reception signal: Output at - 99.0 to - 93.0 dBm Transmit circuit - ANT RF input signal level (1626.5 to 1646.5 MHz): - 2 to +13 dBm - ANT RF output signal level: +41 to 43 dBm (IC-118), +38.5 to 40.5 dBm (IC-119) - Continuous transmission time: More than 15 minutes

TX 5V

Q4

ATT

Limiter

TX IN

R17

CR1

R20

J2

Q2

CR4

BPF

Q1; IC-118: BLF3G21_30 IC-119: MRF6S2001GNR1 Q3 Q1

C32

FL7 RX OUT

L7 RX 5V

U6

ATT

1537 - 1544.2MHz FL6

COMB IC-118:28/7V IC-119:27/7V

ATT

BPF

Duplexer

FL4

GPS

1575.42MHz U5

BPF FL5

U7

J1

U3

U4

U8

DIV

BPF

ATT

27/7V

27/7V 5V SW

U2

Q7 5V RX Q6

5V SW Reg.

U1

U10

U9

5V SW

5V TX

Q5

ANT_RF FELCOM 18: 16P0285 FELCOM 19: 16P0286

Temp Sensor

Fig. 5.2.3 Block diagram of Antenna

5-6 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

0 deg. 90 deg.

ANT_BASE 16P0289

5.2 ADE

The antenna supply: TX 28 V (27 V) / RX 7 V, the transmit signal (1.6 GHz) and receive signal (1.5 GHz) are superimposed on the Antenna coaxial cable connected to the Terminal (Communication) unit. As for voltage of ANT RF TX and RX circuit, the input voltage, TX 28 V (27V) / RX 7V is detected by the comparator, U1. The output controls Q7 and Q6 in order to generate the voltage of 5 V RX and 5 V TX. Also, the Heat detection circuit: U10 is installed to stop the transmission by setting 5 V TX to “OFF” when the temperature is more than +95°C. CR4 on the TX circuit is used as the Limiter. Since the Antenna coaxial cable is short and cable loss is small, the TX PA circuit is protected from the excessive input level even if the ANT RF input level increases. Also, as the level diagram, transmit output of the Terminal unit is 10 to 15 dBm and ANT RF input level is - 2 to +13 dBm. Even though the assumed range of cable loss is 2 to 12 dB, use the coaxial cable having the standard length. For example, if 5D-FB-CV coaxial cable of which standard length is 30 meters is cut into 15 meters, the cable loss is reduced from 8 dB to 4 dB; however the ANT RF circuit does not break.

-148 to -136 dBW/m2

ADE

FELCOM 18: 12 to 16 dBw FELCOM 19: 7 to 16 dBw

-> 117: If C/N increases, the IF AGC value increases. "NG" appears if the Offset value of TCXO is greater than 150 Hz. "OK" appears if both PLL circuits are normal when checking two PLL circuits (1st Lo and 2nd Lo) on the RF CON board. "NG" appears when the voltage supplied to the Antenna unit is not within the specified range due to malfunction of the antenna cable, etc. Control value of TXCO for the reference oscillator on the RF CON board is displayed.

Position Waypoint Course Speed Current NCS Current Channel Current TDM MES Status

GPS Status

DCE memory BBER C/N

Send Level

Rx AGC Level REF Offset Freq. Synthe Local Antenna Power Supply TXCO Control Water Temperature Water Current Depth

Water temperature (MTW) data is displayed. Direction: Direction of the tide (VDR) and Speed: Speed of the tide (VDR) are displayed. Depth of water (DBT) data is displayed.

8-13 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.1 Status monitor

Analysis of NG display BBER (Bulletin Board Error Rate) When the receiving error rate of the bulletin board , which is located at the top of TDM channel is over 80%, the message, "WARNING: BBER over 80%. SCANNING NCS start manually" appears. BBER is calculated by decoding I and Q data on the TERMCPU (COMMCPU) board and then using this data on CPU for calculating the BBER value. When errors are detected in one frame, BBER is raised at one count per frame, and is the addition of 100 frames. If the BBER value exceeds 80%, FELCOM 19 starts receiving operation for NCS SCAN. As for FELCOM 18, receiving operation for NCS SCAN is not performed. Change the ocean region manually. As possible defective area, malfunction of the receiving circuit is expected. - Antenna unit - RF CON board - TERMCPU (COMMCPU) board - Antenna coaxial cable and coaxial connector Note) If BBER increases even though the C/N level is OK, mixing of noise and interference from other device is suspected.

C/N Even if the equipment is properly operating, "NG" appears when the receive signal is weak. The BPSK demodulated 2nd IF-I and -Q data are decoded at the TERMCPU (COMMCPU) board, and this data is used for calculating the C/N value on the CPU. When the C/N level of the receive signal is greater than 31 dB, "OK" appears. Also, the C/N value is only used for judging OK and NG. The followings are the parts which the error may be occurred; - Antenna unit - RF CON board - TERMCPU (COMMCPU) board - Antenna coaxial cable and coaxial connector - Antenna blocking

8-14 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.1 Status monitor

Send Level The send level detects the power supply current supplied to the Antenna unit via the Antenna coaxial cable when the voltage upon transmission is 28 V (27 V) and the voltage upon reception is 7 V and displays the detected level. TERMPWR (COMMPWR) board detects the send level. The detected level upon transmission is "ANT TX" signal and the detected level upon reception is "ANT RX" signal. "OK" appears if the value is lower than "25" upon reception and the value is greater than "FELCOM 18: 100/FELCOM 19: 25" upon transmission. For example, 10 appears upon reception and FELCOM 18: 222 appears upon transmission. When attempting to transmit while the Send Level is lower than the specified value, the message "TROUBLE: Carrier power level." appears. The followings are the parts which the error may be occurred; - Antenna unit - RF CON board - TERMPWR (COMMPWR) board - Antenna coaxial cable and coaxial connector

Antenna Power Supply Voltage of TX28 (27) V/RX 7 V supplied to the Antenna unit via the Antenna coaxial cable appears. The TERMPWR (COMMPWR) board detects the voltage and the detection signal, which is obtained by dividing the voltage is "Check V." When the voltage is out of the ratings for transmitting and receiving, "NG" appears. Also, the message "TROUBLE: ANT power voltage abnormality." is sent. Conditions for outputting the message are the voltage for transmitting is out of the range "26 to 31 V" and the voltage for receiving is out of the range "6 to 9 V." The followings are the parts which the error may be occurred; - Antenna unit - TERMPWR (COMMPWR) board - Antenna coaxial cable and Coaxial connector

8-15 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.1 Status monitor

Rx AGC Level As for AGC, IF AGC and RF AGC are input from the TERMCPU (COMMCPU) board to the RF CON board. As for the RX AGC Level, the IF AGC level (40 to 245) appears. RF AGC is not used. "NG" appears when the level is less than 60. For example, relation between the C/N value and RX AGC Level is as follows. However, the Rx AGC Level differs slightly due to loss of the Antenna coaxial cable even if the C/N value is the same. AGC Level increases if the Antenna coaxial cable loss is small. C/N Rx AGC Level

29dB

31

33

36

100

105

117

123

ANT Open 40

The followings are the parts which the error may be occurred; - Antenna unit - RF CON board - Antenna coaxial cable and Coaxial connector

REF Offset Freq. "NG" appears if the value is greater than 150 Hz. If the PLL local frequency is shifted, the error rate increases without correcting the frequency. PLL control converts the receiving frequency from the satellite to base band on the CPU in TERMCPU (COMMCPU), performs FFT analysis, and controls the TCXO to make frequency/phase difference match the received modulation rate (ex; 1200 sps). Output of TCXO (30.72 MHz) is the reference frequency of 1st Lo and 2nd Lo PLL circuits. When this frequency is controlled, PLL output frequency changes. In this way, the PLL output frequency is controlled to match the relation of frequency. REF Offset Freq displays the offset value of TCXO. If the REF Offset Freq value is "0," the relation between the receive frequency and PLL local frequency matches. The followings are the parts which the error may be occurred: - RF CON board - TERMCPU (COMMCPU) board.

8-16 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.1 Status monitor

Synthe Local Lock Detect signals of 1st Lo and 2nd Lo PLL circuits on the RF CON board are monitored. If any of PLL circuits is unlocked, "NG" appears. Also, the message "TROUBLE: Synthesizer UNLOCK." is output. The followings are the parts which the error may be occurred: - RF CON/CPU board - TERMCPU (COMMCPU) board.

TCXO Control Control status of the reference oscillator: TCXO (30.72 MHz) is displayed. The value varies depending on TCXO variation and received frequency. The range is from 818 to 4095. Reference) The control voltage setting for the reference oscillator (TCXO) is stored in EEPROM and fine control (narrow search) is performed on the basis of the previous setting at power-up. However, if the NCS common channel cannot be received for one minute, coarse control (wide search) and fine control (narrow search) are performed. When [Option] -> 8.Test -> 3.Diagnostic is executed in Furuno service mode, the TCXO Control value (coarse control value and fine control value) can be checked. TCXO Control on the Status screen displays the coarse control value.

8-17 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.2 [Option ] -> 8. Test

8.2 [Option] -> 8. Test 8.2.1 PV (Performance Verification) TEST PV test is for checking performance of MES (FELCOM 18 and FELCOM 19). The message is exchanged between MES and LES. PV Test is performed by [Option] -> 8.TEST -> 1.PV Test. 1. PV test sequence 1. Start the PV test. 2. The MES sends the request signal to NCS in order to perform the PV test. 3. When NCS receives the signal, the NCS returns the acknowledgement signal to MES. 4. The MES, upon receipt of acknowledgement from NCS, goes into pending state. 5. NCS selects an appropriate LES to perform the PV test. 6. The designated LES transmits a message to the MES. 7. Then, the MES transmits the message to the LES. 8. The Distress alert test starts and the MES automatically starts the Distress alert test within two minutes. 9. When the distress alert test is finished, the results of the PV test are sent from LES to finish the PV test.

2. Executing the PV test Before starting the PV test, check the following. Log in to the system? Is the message "Current Status" that appears the lower left of the screen "IDLE?" Is "C/N" "OK?" Is Current Channel is “SYNC?” Procedure) 1. Open [Options] -> 8.TEST -> 1.PV Test, select "Yes", and then press [Enter]. 2. PV test is started. The PV test progress can be checked on the "Current Status" display. Also, the message appears on the screen. 1) When NCS replays, "PENDING" appears on Current Status. 2) When the test is automatically starts, "TESTING" appears on Current Status. 3) The message for the test is sent from LES to MES. 4) The message for the test is sent from MES to LES. 5) The Distress alert test sequence starts and the Distress alert test is started automatically two minutes later. 6) The test result is received.

8-18 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.2 [Option ] -> 8. Test

3. After finishing the test, "IDLE" appears on "Current Status." 4. Check the PV test result. Also, the result is automatically printed out.

3. Checking PV test result Open [Option] -> 8.Test -> 2.PV Test Result, and then check the PV test result. To print out the test result, press [P] key while holding down [Ctrl] key. Result of “PV Test Result” can be stored. Perform “Export” by -> [Setup] -> 8.Configuretion -> 6.Export/Import -> Test. For details, refer to 8-42 pages.

8-19 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.2 [Option ] -> 8. Test

Test Date & Time The date and the time when the PV test is executed appear. Attempts The number of times PV test is tried after the last PV test was successful appears. BBER When the error rate of Bulletin Board Error Rate is low, "Pass" appears. If the error rate is high, "Fail" appears. Shore to Ship Attempts Number of announcements that MES responded to LES is displayed. - First attempt, Second attempt, Third attempt, Third attempt failed Ship to Shore Attempts Number of requests that LES took the assignment from MES is displayed. - First attempt, Second attempt, Third attempt, Third attempt failed Distress Alert When the distress alert test is OK, "Pass" appears. - Pass : Not Applicable, Test OK, Nature of Distress: not Default, Null Data, Automatically Activated - Fail : No Response, Incorrect Protocol, Invalid Data Format Signal Strength When the signal strength of the signal from MES which is received by LES is within the tolerance, "Pass" appears. - Pass : Less than Std. Level, Greater than or equal to Std. Level, Greater than Std level +3, +6, +10, +13, +16 dB - Fail : No response, unreadable Overall Result When the PV test result is passed, "Pass" appears. - Pass : Applicable tests pass - Fail : Forward message transfer fail Return message transfer fail Signal unreadable, Signal level excessive Distress alert test fail Unspecified fail

8-20 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.2 [Option ] -> 8. Test

8.2.2 Diagnostic Test Diagnostic Test is performed by [Options] -> 8.Test -> 3.Diagnostic Test. Contents of the result to be displayed vary depending on Normal mode and Furuno service mode. In Furuno service mode, details of the program number an STATUS information are added. To enter Furuno service mode, [Setup] -> 1.System Setup -> Command Screen. JOB No. : furunoservice Password: felcom18 (felcom19) Result of “Diagnostic Test” can be stored. Perform “Export” by -> [Setup] -> 8.Configuretion -> 6.Export/Import -> Test. For details, refer to 8-42 pages.

Normal mode display

Detail program version appears. Display in Service mode

Display of STATUS is added. The last five TROUBLES and WARNINGS stored in the SYSTEM LOG are displayed.

*****

Access to “Diagnostic Test” directly; [F7] -> [Alt]+8 -> [Ctrl]+TEST Terminate: [Esc] x 4 times

8-21 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.2 [Option ] -> 8. Test

1. Diagnostic Test display area Program Ver. The detailed version appears in Furuno service mode. The following table shows the version as of Oct, 2012. “PC TERMINAL Ver.” of FELCOM 18 and a “Rev.” are displayed by the PC terminal side. All the following tables are displayed. Program TERMCPU

FELCOM 18 Normal Mode 1650247-01

Rev Boot no. Starter no. PC TERMINAL

1650240-01

Rev.

Service Mode 1650247-01.04 1819 2012.07.01.04 1650236-01.01 0550252-01.02 1650240-01.04 1819 2012.07.30

FELCOM 19 Normal Mode 1650248-01

Service Mode 1650248-01.04 1819 2012.07.30

1650241-01

1650238-01.01 0550252-01.01 1650241-01.04 1819

2012.07.30

ROM, RAM, EEPROM This test is performed when the Diagnostic Test is carried out. The R/W test result of memory on the TERMCPU (COMMCPU) board is displayed.

FELCOM 18 FELCOM 19

ROM

RAM

EEPROM

U7, U8(Flash): W25Q64CVSSIG U8, U9(Flash): W25Q64CVSSIG

U5(SDRAM): MT46H8M16LFBF U10(SDRAM): MT46H8M16LFBF

UX20: 25AA512_1 U7: 25AA512_1

GPS State This test is performed when the Diagnostic Test is carried out. Settings and GPS status of [Setup] -> 1.System Setup -> Nav Port are displayed. When GPS data is input from the external GPS, the GGA sentence must be inputted in order to display the state of GPS, such as INT and ACQ.

2. REMOTE BOX display area When entering Furuno service Mode from [Setup] -> 1.System Setup -> Command Window, the setting status of "1.Remote Box Setup" appears. However, only "ON/OFF" setting appears for SSAS, and SSAS types, such as Standard, Russian and USCG, do not appear.

8-22 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.2 [Option ] -> 8. Test

3. MAIN STATE display area Contents that are displayed are the same those appear in Status Monitor state. BBER This is the BBER value when the Diagnostic Test is performed. C/N This is the C/N value when the Diagnostic Test is performed. Rx AGC Level This is the Rx AGC Level when the Diagnostic Test is performed. The range is from 40 to 245. REF offset Freq This is the REF offset Freq value when the Diagnostic Test is performed. Synth Local Status of two PLL circuits of the RF CON board appears when the Diagnostic Test is performed. Status of two PLL circuits are classified between "Local PLL and 2nd PLL." TCXO Control The coarse control value (818 to 4095) and fine control value (0 to 4095) of TCXO when the Diagnostic Test is performed are displayed. TxRx data Transmit/receive voltage and current detection level of "Antenna Power Supply" that appear on the Status screen are displayed. However, transmit voltage/current level and receive voltage/current level do not appear at the same time. The displayed value is the actual display example. -Tx Power Supply: FELCOM 18 -> 27.6V,

FELCOM 19 -> 27.0V

-Tx current level: FELCOM 18 -> 215, FELCOM 19 -> 66 Transmit voltage and current detection level, that are used during communication and recorded on the latest Sent Messages Log, are displayed. However, the above values are deleted when receiving the message including EGC. -Rx Power supply: FELCOM 18 -> 7.1V,

FELCOM 19 -> 7.0V

-Rx current level: FELCOM 18 ->100, FELCOM 19 -> 105 Receive voltage and current detection level are displayed when reception, which is recorded on the latest Received Message Log and EGC Messages, is carried out. However, the above values are deleted when receiving the message.

8-23 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.2 [Option ] -> 8. Test

4. STATUS display area The latest five Warning and Trouble events are displayed. Five items are displayed and these items are not deleted even if the system is turned off. See "Appendix 1. Event List" for contents to be displayed. However, even if the sentence indicating the event may be different, the same event is indicated if the event number is the same. The event number consists of the following five digits: "Category Number (one digit) + Type Number (one digit) + Event Message Number (three digits)" Category Number 1: Hardware 2: Navigation 5: Distress Alert 6: Transmit Type Number 1: Information

3: System 7: Receive

2: Warning

4: Data Report 8: Mail

9: Print

3: Trouble

For example, in "32007 External NAV equipment failure," the category is classified as "Warning" at "System," and contents of the event are "External NAV equipment failure."

8-24 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.2 [Option ] -> 8. Test

8.2.3 Distress Button Test (Distress/SSAS Button Test) 1. Distress Button Test FELCOM 18 See page 4-11 for details. This test is valid even if IC-305 is set to "OFF" at "Remote Box Setup" setting. When entering Distress Button Test, the unit is normal if the message "INF: Distress Buttons entered into TEST MODE." appears, and the message "INF: DISTRESS ALERT UNIT works correctly." appears when the [Distress] button is pressed. FELCOM 19 The “Distress Button Test” item if deleted from Test Menu.

2. SSAS Button Test See page 4-28 for details. This test cannot be performed unless the SSAS function is set to "ON" in "Remote Box Setup" in Command Window and "SSAS Manager Mode" is entered. FELCOM 18 The menu display changes from "4.Distress Button Test" to "4.Distress/SSAS Button Test." FELCOM 19 "SSAS Button Test" is added. “SSAS button test” can be performed along with “Distress button test.” When starting the “SSAS button test”, the message "INF: Distress Buttons/SSAS entered into TEST MODE" appears, and the SSAS unit is working properly if the message "INF: SSAS UNIT works correctly." appears.

8-25 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.3 [Options] -> 9.Maintenance (checking Log)

8.3 [Options] -> 9.Maintenance (checking Log) Log can be checked in Maintenance menu. Only "1.Current Position Log" appears in Normal mode. When entering Furuno service mode, 2. System Log, 3. Term Operation Log, 4. Sent Report Log, 5. Communication Log are added.

}

These logs are added when entering Service mode.

8.3.1 "1. Current Position Log" The Position Log is recorded at power-on, and the Position Log is updated every hour. A maximum of 100 positions are displayed and the log is not deleted even if the unit is turned off.

8-26 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.3 [Options] -> 9.Maintenance (checking Log)

Op. Time (sec) This is the total number of seconds that the unit is kept ON. Number of seconds to be displayed is in the range from 0 to 4294967295 seconds. This value is reset to "0" by Clear EEPROM. Date & Time The detected date and time are displayed. These data are the ZDA>RMC sentence of the internal GPS (ZDA) or external GPS. Range (From No. / To No.) This is the setting of display range of Log.

Total The number of items in the log is displayed. The maximum number is 100 items. [Ctrl] + [F]: Search Keyword can be searched. The following screen appears when [F] key is pressed while holding down [Ctrl] key. Entering the keyword to be searched and executing Search Start jumps to the detected line. However, "No." is excluded.

8-27 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.3 [Options] -> 9.Maintenance (checking Log)

[Ctrl] + [E]: Export Current Position Log can be stored. The following [Save] screen appears when [E] key is pressed while holding down [Ctrl] key. The log is stored by selecting "A:¥ Drive" of the internal memory or "C:¥ Drive" of SD card and then entering the file name. As for PC terminal for FELCOM 18 and FELCOM 19, operation for storing a file on PC needs to be done. Save [A:¥ -- Filename --------- Size ------------------- Date & Time ---SD Card

0 Files exist To View : SPACE

]

25966864 bytes free Make Dir : INS Remove Dir : DEL

[Ctrl] + [P]: Print Current Position Log can be printed out. When [P] key is pressed while holding down [Ctrl] key, all Current Position Logs are printed out. When printing out the log after specifying the range to be printed out, press [Ctrl] + [P] after specifying the range with "Range (From No. /To No.)" operation.

8-28 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.3 [Options] -> 9.Maintenance (checking Log)

8.3.2 "2. System Log" The log is recorded when an event occurs. The maximum number of items to be displayed is 100. See "Appendix -1 Event List " for contents of events.

Op. Time (sec) This is the total number of seconds that the unit is kept ON. Number of seconds to be displayed is in the range from 0 to 4294967295 seconds. Date & Time The detected date and time are displayed. These data are the ZDA>RMC sentence of the internal GPS (ZDA) or external GPS. Range (From No. / To No.) This is the setting of display range of Log. Total The number of items in the log is displayed. The maximum number is 100 items. [Ctrl] + [F]: Search Keyword can be searched. The following screen appears when [F] key is pressed while holding down [Ctrl] key. Entering the keyword to be searched and executing Search Start jumps to the detected line. However, "No." is excluded.

8-29 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.3 [Options] -> 9.Maintenance (checking Log)

[Ctrl] + [E]: Export System Log can be stored. The following [Save] screen appears when [E] key is pressed while holding down [Ctrl] key. The log is stored by selecting "A:¥ Drive" of the internal memory or "C:¥ Drive" of SD card and then entering the file name. As for PC terminal for FELCOM 18 and FELCOM 19, operation for storing a file on PC needs to be done. Save [A:¥ -- Filename --------- Size ------------------- Date & Time ---SD Card

0 Files exist To View : SPACE

]

25966864 bytes free Make Dir : INS Remove Dir : DEL

[Ctrl] + [P]: Print System Log can be printed out. When [P] key is pressed while holding down [Ctrl] key, all System Logs are printed out. When printing out the log after specifying the range to be printed out, press [Ctrl] + [P] after specifying the range with "Range (From No. /To No.) " operation.

8-30 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.3 [Options] -> 9.Maintenance (checking Log)

8.3.3 "3. Term Operation Log" Log for terminal operations is displayed. The maximum number of items to be displayed is 1000.

FELCOM 18 PC terminal display

K/M K indicates keyboard operation and M indicates mouse operation. As for M, X-Y coordinates of the pointer (X: 347 and Y: 007) appear. Key Code [Key] The entered key code and names of keys, such as [ENTER] and [Esc], appear. Action Key operation status is displayed. "Down" indicates Key Down and "Up" indicates Key Up. For example, when [Enter] is operated, a pair of “Down” and “Up” is recorded. WindowName The title of the window on which operation is made is displayed. Op. Time This is the total number of seconds that the unit is kept ON. Number of seconds to be displayed is in the range from 0 to 4294967295 seconds.

8-31 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.3 [Options] -> 9.Maintenance (checking Log)

Date & Time (UTC) The detected date and time are displayed. These data are the ZDA>RMC sentence of the internal GPS (ZDA) or external GPS. Range (From No. / To No.) This is the setting of display range of Log. Total The number of items in the log is displayed. The maximum number is 1000 items. [Ctrl] + [F]: Search Keyword can be searched. The following screen appears when [F] key is pressed while holding down [Ctrl] key. Entering the keyword to be searched and executing Search Start jumps to the detected line. However, "No." is excluded.

[Ctrl] + [E]: Export Term Operation Log can be stored. The following [Save] screen appears when [E] key is pressed while holding down [Ctrl] key. The log is stored by selecting "A:¥ Drive" of the internal memory or "C:¥ Drive" of SD card and then entering the file name. As for PC terminal for FELCOM 18 and FELCOM 19, operation for storing a file on PC needs to be done. Save [A:¥ -- Filename --------- Size ------------------- Date & Time ---SD Card

0 Files exist To View : SPACE

]

25966864 bytes free Make Dir : INS Remove Dir : DEL

8-32 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.3 [Options] -> 9.Maintenance (checking Log)

[Ctrl] + [P]: Print Term Operation Log can be printed out. When [P] key is pressed while holding down [Ctrl] key, all System Logs are printed out. When printing out the log after specifying the range to be printed out, press [Ctrl] + [P] after specifying the range with "Range (From No. / To No.)" operation.

8.3.4 "4. Sent Report Log" This is the log of Data Report sent by the Polling command and Data Report, which is edited in [Report] menu and transmitted. However, Message Report is not recorded. Also, logs of LRIT and VMS appear. However, as for VMS, this log appears if "false" is set for "Hidden VMS" in the VMS setting file. The maximum number of items to be displayed is 100.

DNID The DNID used for Sent Report is displayed. LES The LES on which the message is processed is displayed.

8-33 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.3 [Options] -> 9.Maintenance (checking Log)

Protocol The protocol used in Report is displayed. -DR (Data Report) When a report is transmitted in [Report] -> 1.Data Report -> Usual Data Report. -EDR (Enhanced Data Report) When a report is transmitted in [Report] -> 1.Data Report -> Enhanced Data Report. -PADR (Pre-Assigned Data Report) When PADR is transmitted by using the Polling command. -EPADR (Enhanced Pre-Assigned Data Report) When a report is transmitted in [Report] ->3.Enhanced Pre-Assigned Data Report (EPADR). -POLL (Polling) When a Data Report other than PADR is transmitted by using the Polling command. Reporting Successful indicates success of Reporting and Failure indicates failure of Reporting. Date & Time (UTC) Transmitted date and time are displayed. These data are the ZDA>RMC sentence of the internal GPS (ZDA) or external GPS. Range (From No. / To No.) This is the setting of display range of Log. Total The number of items in the log is displayed. The maximum number is 100 items. [Ctrl] + [F]: Search Keyword can be searched. The following screen appears when [F] key is pressed while holding down [Ctrl] key. Entering the keyword to be searched and executing Search Start makes the cursor jump to the detected line. However, "No." is excluded.

8-34 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.3 [Options] -> 9.Maintenance (checking Log)

[Ctrl] + [E]: Export Sent Report Log can be stored. The following [Save] screen appears when [E] key is pressed while holding down [Ctrl] key. The log is stored by selecting "A:¥ Drive" of the internal memory or "C:¥ Drive" of SD card and then entering the file name. As for PC terminal for FELCOM 18 and FELCOM 19, operation for storing a file on PC needs to be done. Save [A:¥ -- Filename --------- Size ------------------- Date & Time ---SD Card

0 Files exist To View : SPACE

]

25966864 bytes free Make Dir : INS Remove Dir : DEL

[Ctrl] + [P]: Print Sent Report Log can be printed out. When [P] key is pressed while holding down [Ctrl] key, all Sent Report Logs are printed out. When printing out the log after specifying the range to be printed out, press [Ctrl] + [P] after specifying the range with "Range (From No. /To No.)" operation.

8-35 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.3 [Options] -> 9.Maintenance (checking Log)

8.3.5 "5. Communication Log" This is the log of transmitted and received messages, EGC reception, VMS and SSAS, etc. The maximum number of items to be displayed is 100.

S/R S: Send message R: Received message Cate The service type is displayed. Table 8.3.1 Cate list Cate

Remarks

MSG EGC DR EDR PADR EPADR POLL SSAS DR+VMS EDR+VMS PADR+VMS EPADR+VMS PLL+VMS

This is the Destination type defined in [Transmit] -> 1.Transmit Message. EGC reception While operating in VMS mode, these items do not appear if "Enable" is set for "Hidden VMS" in the VMS setting file. This item appears while in SSAS Manager mode. This item appears if the Communication Log is opened by the VMS PC terminal.

8-36 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.3 [Options] -> 9.Maintenance (checking Log)

Type Communication type used for transmission is displayed. TLX: TELEX, EML: E-Mail, FAX: Fax, PSD: PSDN, X40: X400, DND: DNID, END: ENID "--" is displayed for the received message.

SMS: SMS, SPC: Special,

Ch, Ch Num The channel type is displayed. MSG: Massage Channel, TDM: TDM Channel, SIG: Signaling Channel and their channel numbers are displayed.

Data Report Distress Polling Status Commission & Test Reqest Registration MES Status MES Status Request TDM Assignment TDM Release Ack

Network

TDM Channel

Message Channel

Signaling Channel

Data

Acknowledgment Acknowledgement Request Bulletin Board Clear Data Packets Distress Alert Ack Distress Test Request Forced Clear Logical Channel Assignment Message Status Request Status Test Results

Network Coordination Station (NCS)

Confirmation Distress EGC Polling Request MES Status MES Status Request TDM Release Test Results

Data Report Distress Alert Initiate Call Log in Request Log out Request Message Status Request Test Request

NCS Common Channel

Acknowledgement Announcement Response Assignment Response Clear Data Reporting Distress Alert Forced Clear Assignment Request Request for Transfer Status Request for Message Status

Interstation Signaling Channel

Signaling Channel

Land Earth Station (LES)

NCS Signalling Link

Announcement Bulletin Board Confirmation Distress Alert Ack EGC Log in Ack Log out Ack Network Update Poll Request Status

Mobile Earth Station (MES)

Fig. 8.3.1 INMARSAT C system configuretion

8-37 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.3 [Options] -> 9.Maintenance (checking Log)

Pri Priority sequence of communication is displayed. -Nrm: Normal Message → Target: Message and EGC Note) This is the Destination type when Normal is set for Priority in Message: [Transmit] -> 1.Transmit Message. For example, TELEX, E-Mail and FAX, etc. are displayed. -Dis: Distress Message → Target: Distress Message (TELEX) and EGC -Urg: Urgency Message → Target: EGC -Saf: Sefaty Message → Target: EGC -***: → Target: Communications other than above communications (Data Report) LES The LES ID on which the message is processed is displayed. Size The size (number of bytes) including message and header is displayed. In the Inmarsat C, the number of bits is limited to 32768 bytes. "-----" appears upon failure. St Result of transmission is displayed. "S" indicates Success of transmission and "F" indicates that transmission failed. EGC and received messages are left blank. Date & Time (UTC) Transmitted date and time are displayed. These data are the ZDA>RMC sentence of the internal GPS (ZDA) or external GPS. Range (From No. / To No.) This is the setting of display range of Log. Total The number of items in the log is displayed. The maximum number is 1000 items. [Ctrl] + [P]: Print Communication Log can be printed out. When [P] key is pressed while holding down [Ctrl] key, all Communication Logs are printed out. When printing out the log after specifying the range to be printed out, press [Ctrl] + [P] after specifying the range with "Range (From No. / To No.) " operation.

8-38 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.4 [Options] -> 7. LES Information

8.4 [Options] -> 7. LES Information LES information of the ocean region is automatically downloaded from NCS at log-in, and the information is reflected on [Options] -> 7.LES Information.

1. LES ID LES number 2. Name The registered LES name appears in [Setup] -> 8.Configuration -> 2.LES List. If the name is not registered, the display is left blank. 3. Status The display format for Status is B8 to B1. For example, if B8 is "1," Return link speed is 600 sps. Table 8.4.1 Status list Bit No.

Status

Flag

B8

Return link speed

B7

Operational or spare satellite operation

B6

LES Status

B5

LES Status

B4

Used only by land earth stations

B3-1

spare

1 0 1 0 1 0 1 0 1 0 0

Meaning 600 sps 300 sps Operational spare In service Out of service clear congested Terrestrial links open Terrestrial links closed

8-39 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.4 [Options] -> 7. LES Information

4. Services The service provided by LES is displayed. LES service is displayed by the character when the bit is 1. If the bit is "0," the display is left blank. The display format for Status is 1B8 to 1B1 and 2B8 to 2B1. However, 2B7 and 2B6 are omitted. Table 8.4.2 LES Service Bit No. 1B8 1B7 1B6 1B5 1B4 1B2 1B2 1B1 2B8 2B7 2B6 2B5 2B4 2B2 2B2 2B1

Flag 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0

Meaning Maritime distress alerting No Maritime distress alerting SafetyNET traffic No SafetyNET traffic Inmarsat-C traffic No Inmarsat-C traffic Store and Foward No Store and Foward Half duplex No Half duplex Full duplex No Full duplex Closed network No Closed network FleetNET traffic No FleetNET traffic Prefixed store and forward message supported Prefixed store and forward message not supported Land mobile alerting No Land mobile alerting Aero-C service supported Aero-C not service supported ITA2 transmission supported ITA2 transmission not supported Data transmission supported Data transmission not supported Basic X.400 supported Basic X.400 not supported Enhanced X.400 supported Enhanced X.400 not supported Low power C MES supported Low power C MES not supported

Display A Not displayed S Not displayed C Not displayed T Not displayed H Not displayed D Not displayed N Not displayed F Not displayed P Not displayed Not used in this equipment.

I Not displayed B Not displayed X Not displayed E Not displayed L Not displayed

5. TDM ch. TDM channel used by LES for transmitting is displayed.

8-40 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.5 Setting of DIP switches

8.5 Setting of DIP switches TERMCPU (COMMCPU) has two DIP switches. “OFF” needs to be set to all DIP switches and factory setting must be kept. If settings of DIP switches are changed, DIP switches may not work properly. Booting method, writing of MAC Address and debug mode are defined for these DIP switches.

S2 S4

TERMPWR (16P0287B)

TERMCPU (16P0283B)

COMMCPU (16P0282)

COMMPWR (16P0288)

S2 S3

FELCOM 18

FELCOM 19

8-41 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.6 Export/Import

8.6 Export/Import The configured data and message can be stored, or stored data can be reflected on equipment. Execute [Setup] -> 8.Configuration -> 6.Export/Import. Note) 1) Importing and exporting SSAS data need to be carried out in SSAS Manager Mode. 2) Importing and exporting VMS data is carried out from VMS Terminal PC. 3) The file which Exported can be checked by [File] -> Open or using Text Editor. However, binary data files, such as a Setting files and List files, cannot check the contents. Table 8.6.1 Contents to be exported Items to be exported 1. Sent Message 2. Received Message 3. EGC Message 4. Station List 5. LES List 6. E-Mail/SMS Service List

7. Test

8. Maintenance

Contents to be exported [Logs] -> 1. Sent Message (a maximum of 50 items) [Logs] -> 2. Received Message (a maximum of 50 items) [Logs] -> 3. EGC Message (a maximum of 50 items) [Setup] -> 8. Configuration -> 1. Station List [Setup] -> 8. Configuration -> 2. LES List [Setup] -> 8. Configuration -> 6. E-Mail/SMS Service List [Options] -> 8. Test -> 2.PV Test Result (a maximum of 5 items) 3.Diagnostic (a maximum of 5 items) Note) As for Diagnostic, results of tests in Furuno service mode and Normal mode are stored. [Options] -> 9. Maintenance 1) Current Position Log (a maximum of 100 items) 2) System Log (a maximum of 100 items) 3) Term Operation Log (a maximum of 100 items) 4) Sent Report Log (a maximum of 100 items) 5) Communication Log (a maximum of 100 items) Note) Only Current Position Log is stored in Normal mode.

File name

Checking method

ex; S012027.001

[File] -> Open

ex; R012027.001

[File] -> Open

ex; E0120627.001

[File] -> Open

STATION.DAT

--

LES.DAT

--

EMAIL.DAT

--

DIAGNOST.DAT PVTEST.DAT

[File] -> Open

1) POSTION.DAT 2) SYSTEMLO.DAT 3) OPERATION.DAT 4) SENTREPO.DAT 5) COMMUNIC.DAT

[File] -> Open

8-42 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.6 Export/Import

9. Settings

1) VMS settings Note) VMS Settings need to be exported in VMS Mode, and VMS settings are stored on PC instead of the SD card. 2) SSAS Settings Note) SSAS Settings need to be exported in SSAS Manager mode. 3) EGC Settings [Setup] -> 4.EGC Setup 4) Auto Mode Setting [Setup] -> 5.Auto Mode Setup 5) E-Mail Setting [Setup] -> 6.E-Mail Setup 6) Terminal Settings [Setup] -> 3.Terminal 7) Editor Setting [Setup] -> 2.Editor Setup 8) System Setting [Setup] -> 1.System Setup - MES Operation Mode - NAV Port -Message Output Port - EGC Output Port -Network Setup

VMS.DAT SSAS.DAT EGC.DAT NET.DAT DTE.DAT SYSTEM.DAT

--

8-43 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.6 Export/Import

Table 8.6.2 Contents to be imported Items to be imported Station List

LES List

E-Mail/SMS Service List

Settings

Contents to be imported The Station List registered in [Setup] -> 8.Configuration -> 1.Station List is imported into the Terminal (Communication) unit. The LES List registered in [Setup] -> 8.Configuration -> 2.LES List is imported into the Terminal (Communication) unit. The E-Mail/SMS Service List registered in [Setup] -> 8.Configuration -> 6.E-Mail/SMS Service List is imported into the Terminal (Communication) unit. The following items can be imported into the Terminal (Communication) unit at once. 1) VMS Settings Note) VMS Settings are imported from VMS Terminal PC. 2) SSAS Settings Note) SSAS Settings need to be imported in SSAS Manager Mode. 3) EGC Settings [Setup] -> 4.EGC Setup 4) Auto Mode Setting [Setup] -> 5.Auto Mode Setup 5) E-Mail Setting [Setup] -> 6.E-Mail Setup 6) Terminal Settings [Setup] -> 3.Terminal 7) Editor Setting [Setup] -> 2.Editor Setup 8) System Setting [Setup] -> 1.System Setup - MES Operation Mode - NAV Port - Message Output Port - EGC Output Port - Network Setup

File name STATION.DAT

LES.DAT

EMAIL.DAT

VMS.DAT SSAS.DAT EGC.DAT NET.DAT SYSTEM.DAT DET.DAT

Note) 1) When Settings data is imported, the system is automatically rebooted. 2) When importing VMS Settings data, data stored on the VMS PC terminal is imported. In this case, the directory where VMS.DAT is stored needs to be specified. For example, if VMS.DAT is stored on desktop, the desktop where the folder to be loaded exists needs to be selected. If this selection is not correct, "Load Error!!!" appears.

8-44 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.6 Export/Import

1. Export Procedure) 1. Open "Export to SD" from [Setup] -> 8.Configuration -> 6.Export/Import.

2. Select the item to be exported. For example, select “9.Settings” and then press [Enter] key. Select SD Card and then press [Enter] key. The directory is changed to C:¥ drive.

A drive: FELCOM 18 body memory C drive: SD card Reference) Normally data is stored on the C drive of the SD card, but the data can be stored on the A drive. When saving multiple data, data can be organized by creating directory and storing data in the directory.

3. When [Esc] key is pressed, the pop-up message [Update Yes/No] appears. Select "Yes" and then press [Enter] key.

8-45 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.6 Export/Import

4. When the pop-up message [OK to Export? Yes/No] appears, select "Yes" and then press [Enter] key.

5. The display returns to the Export screen. 6. Open the SD Card by selecting [File] -> Open, and then check that exported Setting data is stored.

2. Creating directory and storing data Procedure) 1. Open "Export to SD" from [Setup] -> 8.Configuration -> 6.Export/Import. 2. Select the item to be exported. For example, select “9.Settings” and then press [Enter] key. Select SD Card and then press [Enter] key. The directory is changed to C:¥ drive. 3. Press [Insert] key. Since the Make Directory screen, enter a directory name (for example, setting), and then press [Enter] key.

8-46 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.6 Export/Import

4. The directory: setting is created. Internal Memory: FELCOM 18 Flash memory “.”: The currently selected directory is indicated. “.. ”: Move to the directory located one level up.

5. Select the created directory: setting and then press [Esc] key. When the pop-up message [Update Yes/No] appears, select "Yes" and then press [Enter] key. 6. When the pop-up message [OK to Export? Yes/No] appears, select "Yes" and then press [Enter] key. 7. The display returns to the Export screen. 8. Open the SD Card by selecting [File] -> Open, and then check that exported Setting data is stored.

8-47 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.6 Export/Import

3. Import Procedure) 1. Open "Import from SD" from [Setup] -> 8.Configuration -> 6.Export/Import.

2. When the item to be imported is selected and [Esc] key is pressed, the popup message [Update Yes/No] appears. Select "Yes" and then press [Enter] key. Note) For example, if Settings are imported, EGC.DAT and DTE.DAT files stored in the directory appears when "Settings" is opened. However, these files do not need to be specified. Only the directory needs to be specified. 3. When the pop-up message [OK to Import? Yes/No] appears, select "Yes" and then press [Enter] key. 4. The Import screen appears.

Reference) 1) If wrong data is selected and Import operation is performed, the pop-up message "Load Error!!!" appears.

2) When setting data is imported, the pop-up message "Please reconnect after 5 seconds" appears and the system is "rebooted."

8-48 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.7 Clearing memory

8.7 Clearing memory Enter Furuno service mode from [Setup] -> 1.System -> Command Window, and then input the memory clear command. Procedure) 1. See page 4-7 and enter Furuno service mode. JOB No.: furunoservice Password: felcom18 (For FELCOM 18) felcom19 (For FELCOM 19) 2. Type the clear command in JOB No. clr intmem Internal memory: A drive is initialized. clr eeprom All items excluding FWD ID, RTN ID and Serial No. are reset. clr backup (For R&D command) Other settings excluding the following items are reset. - FWD ID/RTN ID/Serial No - [EGC] -> EGC Network ID - [Report] -> 1.Data Report, 4.Data Network ID, 5.SSAS Report - [Setup] -> 1.System Setup -> IMN, MES Operation Mode, Nav Port, LAN Port, Message Output Port, EGC Output Port - [Setup] -> 1.System Setup -> Network Setup -> Network -> IP Address, Subnet Mask, DHCP, Gateway - [Setup] -> 1.System Setup -> Network Setup -> Mail Gateway ->SMTP Enable IP Address, Send Limit Size - [Setup] -> 1.System Setup -> 4.EGC Setup, - [Setup] -> 8.Configuration -> 3.EGC Channel List, 4.NCS Channel List - Data Report Programming -> DR/EDR/EPADR - VMS setting 3. When "clr backup" and "clr intmen" are executed, the message "Starting Reboot" appears on the Command Window, and the message "Wait moment" appears when "clr eeprom" is executed and then the system starts "rebooting."

8-49 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.8 Command operation

8.8 Command operation Do not disclose command operations. Commands need to be entered in "Enter JOB No.:" There are commands that cannot be accepted unless the system enters Furuno service mode. [ Main Menu ] 1. Remote Box Setup 2. External Alarm Setup Enter JOB No.: clr eeprom

Table 8.8.1 Command list Command function

Command JOB No.

This command is used to enter Furuno service Mode. This command is used to enter SSAS Manager Mode. SSAS is added to [Report] and SSAS Report cannot be set. This command is used to change the SSAS Password. - Default password: Ship security alert - Common Password: wasuremashita+IMN This command is used to finish the SSAS sequence. This command needs to be entered after entering SSAS Manager Mode. This command is used to exit from SSAS Manager Mode and Service Mode. This command is used to exit from Service Mode. This command is used to exit from SSAS Manager Mode. This command is used to set OFF for Urgent EGC ALM. This command is used to set OFF for all ALM Buzzer output from the body. This command is used to reset "off" setting of the above ALM Buzzer to "on." Ch display When communication is established, transmit and receive channels are displayed at the lower left of the Status Monitor screen.

JOB No.

furunoservice felcom18 felcom19 ssas manager

Password

ship security alert

JOB No.

ssas password

Password

ship security alert

JOB No.

terminate ssas alert

Password JOB No. Password JOB No. Password JOB No. Password JOB No. Password JOB No. Password JOB No. Password JOB No.

N/A quit N/A quit service N/A quit ssas N/A urgent alarm off N/A buzzer off N/A buzzer on N/A mon channel

Password

N/A

Password

8-50 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.8 Command operation

This command is used to monitor external NMEA input on the Command Window. (This command is independent of the setting in [Setup] -> 1.System -> 3.Nav Port.) This command is used to monitor internal GPS output data on the Command Window. This command is used to reset other settings excluding FWD/RTN ID to factory default setting. The command is input after entering Furuno Service Mode. If a command is accepted, the system is rebooted. This command is used to initialize internal memory: A drive. The command is input after entering Furuno service mode. If a command is accepted, the system is rebooted. This command is used to display operation status of Program Report. The "show prog" command needs to be entered after entering Furuno service mode in order to display operation status of Program Report. This command is used to display all stored LES MULTI TDM information. This command is used to display the FWD ID. This command is used to display the EPADR program. The command needs to be entered after entering Furuno Service Mode. This command is used to enable the Standard LRIT function. This command is used to disable the LRIT function. This command is used to enable the Russia LRIT function. This command is used to display the current LRIT mode.

JOB No.

mon nmea

Password

N/A

JOB No. Password JOB No.

mon gps N/A clr eeprom

Password

N/A

JOB No.

clr intmem

Password

N/A

JOB No.

show prog

Password

N/A

JOB No. Password JOB No. Password JOB No.

les multi tdm N/A fwd id N/A slcainfo

Password

N/A

JOB No. Password JOB No. Password JOB No. Password JOB No. Password

lrit on N/A lrit off N/A lrit russia N/A lrit mode N/A

8-51 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

8.9 Antenna unit Maintenance

8.9 Antenna unit Maintenance Check the base of Antenna unit, it has not corroded, or paint has not separated. Paint the portion, when the case of being rusty, and paint have separated. Do not paint Antenna redome. If it paints, sensitivity will be down. Moreover, there is a possibility that Antenna redome may crack.

Do not paint

In case of corroded, Apply Paint.

8-52 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

ChapterChapter 9. Q9. Q&& AA Q1. Is it possible to cut the Antenna coaxial cable? 5-7 Since the “limiter”, which is the circuit protecting from excessive input level is built in the ANT RF board, the Antenna coaxial cable can be cut. Q2. Is there compatibility of Antenna unit between IC-118 and IC-119? 1-5, 5-4 Basically, there is no compatibility between Antenna units. The Antenna unit (IC-119) of FELCOM 19 can be connected to FELCOM 18 as measures for checking equipment. However, if the Antenna unit (IC-118) of FELCOM 18 is connected to FELCOM 19, the COMMPWR board of FELCOM 19 may break. Q3. Is there any guideline for compatibility between Antennas? IM When mounting two Antenna units, distance between Antennas needs to be greater than 1.5 m and difference in level between Antennas needs to be greater than 1 m. See IM for using the Antenna of other equipment. Q4. Are there cautions for replacing the board? Summary - 6 When replacing TERMCPU board and COMMCPU board, original EEPROM of these boards need to be used. ID-related data, setting data, such as VMS and SSAS, and system settings are stored on EEPROM. The same action needs to be taken when replacing equipment. Q5. Is there difference between FELCOM 18 and FELCOM 19? 1-1 FELCOM 18 is Class-2 Inmarsat-C system for GMDSS ship, EIRP is 12 to 16 dBW. FELCOM 19 is Class-2 Mini-C system for Non-GMDSS ship EIRP is 7 to 16 dBW. Both equipment are compliant with SSAS, VMS and LRIT function. Q6. Where can the program version are checked? 6-2 Open [Options] -> 8.Test -> 3.Diagnostic Test and execute "Diagnostic Test." As for detail S/W Version, check the S/W Version in Furuno service mode. Q7. The VMS PC Terminal program cannot be installed on PC. 7-1 PC terminal software and VMS PC terminal software cannot be installed on the same PC. Delete the PC terminal software. Q8. The program cannot be updated. 6-4 When updating the program by use of "Updater," the program file needs to be placed under (root) the C drive of the PC. For example, the program may not be updated if the program file is placed on desktop. When updating the program by use of “upf18term.bat”, the program file can be placed on any position. Is Network set on PC? As for both FELCOM 18 and FELCOM 19, "172.31.16.2/255.255.0.0" is set for the Network address.

9-1 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Chapter 9. Q & A

Q9. Connection between PC terminal and Terminal unit cannot be established. Is Network setting performed on PC? The IP Address of the Terminal unit is 172.31.16.0/16. - Felcom 18: Is "ON" set to [Setup] -> 1.System Setup -> LAN Port? - Felcom 19: Open [Setup] -> 3.Terminal and execute "Connection."

7-11

Q10. How to re-register IMN 4-3 IMN can be changed by typing "IMN" while pressing and holding down [Ctrl] and [Alt] keys. The input IMN is reflected on the Status screen. Q11. How to check transmission and reception Summary - 5 A message needs to be sent to the own ship. Or, the Loopback test needs to be performed using "91." Q12. How to set IC-305, IC-306 and IC-307 4-9, 4-10 Jumper setting needs to be made on each unit. Enter Furuno service mode by selecting [Setup] -> 1.System Setup -> Command Window and then set "Remote Box Setup." Q13. What are special operations? See Summary. How to enter Furuno service mode is important. Command operations and VMS setting are special operations.

Summary - 3, 8-50

Q14. Is there any method to clear memory? 8-49 After entering Furuno service mode, memory clear commands, such as “clr eeprom” and “clr intmem”, can be used on the Command Window. FWD ID and RTN ID are not cleared even if any command is executed. Q15. Is there any method to check whether SSAS is active? As for FELCOM 15, the "dot" mark is displayed at the lower left of the Status window. However, there is no display for FELCOM 18 and FELCOM 19. Q16. Is Version display of S/W displayed as the Diagnostic Test result? 8-21 Execute the Diagnostic Test in Furuno Service Mode. Setting of REMOTE BOX, STATUS and the latest System Log appear along with detailed S/W Version. Q17. TX Power Supply and Current Level are not displayed on STATUS display for the result of Diagnostic Test. Is this failure? 8-23 Transmit voltage and current level and receive voltage and current level do not appear at the same time. Transmit voltage and current level that are used during communication and recorded on the latest Sent Messages Log are displayed. However, the above values are deleted when receiving the message including EGC. When a message is transmitted, the receive voltage and current level disappear and then transmit voltage and current level appear.

9-2 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Chapter 9. Q & A

Q18. Does the 5-digit number displayed on the System Log have meaning? 8-24, AP.1 The number consists of "Category Number (one digit) + Type Number (one digit) + Event Message Number (three digits)". Q19. Where can the System Log be checked? 8-26 Enter Furuno service mode and then open [Option] -> 9.Maintenance. Only Current Position Log appears if the system is not in Furuno service mode. Q20. Is it possible to Export and Import SSAS setting? 8-42 SSAS setting cannot be exported or imported unless the system enters SSAS Manager Mode. Q21. Is there setting of DIP SW? 8-41 There are two DIP switches on TERMCPU (COMMCPU). All DIP switches need to be set to “OFF”. Do not change the setting. Q22. Is it possible to use a USB memory? The USB port is dedicated for Keyboard. Therefore, USB memory cannot be used. Q23. Where does the SSAS unit: IC-307 need to be installed? The SSAS unit is installed at least two positions. Normally, the SSAS unit is installed at the position where W/H and one more position. IC-307 needs to be installed at an unnoticeable place, such as the back of the table. Three SSAS units can be connected to Furuno SSAS system. Q24. Why is the daisy chain connection used for connecting IC-307? 4-29 The daisy chain connection is used to detect error of the connection cable of IC-307. If a cable error is detected, the error message "SSAS UNIT connection abnormality" appears. The [SSAS] port on the IC-318: Junction box and IC-307 (No.1, 2, 3) are connected in such a manner that they are connected by using one cable. Also, only for IC-307 at the end, JP-1 needs to be set to ON (jumper) and other IC-307 needs to be set to OFF (open). For example, if ON is set to JP-1 on No.1 IC-307, cable wiring of No.2 and No.3 IC-307 are not checked. Q25. Why is the number of units connected to IC-307 limited to three units? Since IC-307 is connected in parallel, there is no limit. However, if the Alert button is pressed on more than three units, photocouplers in IC-307 cannot be fully driven; therefore the number of units is limited to three units.

9-3 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Chapter 9. Q & A

Q26. Procedure for setting SSAS 4-17 1) Make jumper setting for IC-307. 2) Enter Furuno service mode and carry out Remote Box Setup. Type "furunoservice"/"felcom18 (felcom19)" on Command Window in order to enter Furuno service mode. 3) Enter SSAS Manager Mode and then set [Reports] -> 5.SSAS. Type "ssas manager/ship security alert" on Command Window in order to enter SSAS Manager Mode. 4) When setting is finished, execute “Distress/SSAS Button Test” in [Options] -> 8.Test. 5) Send the SSAS Test Message. 6) Type "quit" on Command Window to quit Furuno service mode and SSAS Manager Mode. Q27. What will happen if the system is turned ON while SSAS button is set to ON? 4-28 - FELCOM 18: SSAS does not activate. The error message "Please retune the SSAS button into OFF-SATE" appears. Set the Alert button OFF. - FELCOM 19: The test message is sent 30 seconds after entering Test Mode. The message to be displayed is "SSAS test message will be transmitted in 30sec. Please turn off the SSAS button if the SSAS test message transfer is unnecessary." Q28. Since the password for entering SSAS Manager Mode is changed, the system cannot enter this mode. 4-22 Enter the common password: wasuremashita+IMN. For example, if IMN is 443212310, type "wasuremashita+443212310." Q29. What are differences among Standard, USCG and Russia SSAS? 4-18 As for USGC SSAS, momentary switch is used for the Alert button. A ship of U.S. registry must equip this type of SSAS. Position data requested from Russia SSAS is "GL" at "GL: GLONASS" EXT. Also, how to activate and stop SSAS vary depending on SSAS types. Q30. How to set VMS 4-41 1) Connect Terminal unit (Communication unit) to VMS PC terminal. 2) Open [Reports] -> 0.VMS. 3) Enter Password: 123456789. 4) When the VMS Mode screen appears, set "ON" for VMS function, open "LOAD" select the VMS file to be set, and then click "Apply."

9-4 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Chapter 9. Q & A

Q31. How is LRIT set? 4-54 Basically, no setting is required. Reporting starts according to the programmed Polling Command from the LES. If LRIT ON Command: lrit on is entered in Command Window, LRIT is prioritized over EGC reception. If FELCOM 18 is equipped for GMDSS type, do not set "LRIT ON." Q32. Is it possible to operate both LRIT and VMS? 4-55 Basically, both LRIT and VMS can be operated. As for VMS, the event is reported to valid DNID when an event occurs. As for some VMS setting files, information, which is irrelevant to LRIT, is also reported; therefore equipment for LRIT and equipment for VMS need to be separated. Q33. Is there any method to check operating status of Data Reporting? 4-56 Enter Furuno service mode from Command Window, type "Show prog." As for reporting data by use of the EPADR protocol, type "slcainfo." Schedule of the next report, etc. can be checked. Q34. What is the difference between Data Report and Message Report in [Reports] menu? 4-36 This is the difference of Data Report protocol. A user does not care the protocol, and all items to be reported are NAV data. Also, the service defined as Data Report is operated by use of Signaling Channel. However, the Message Report uses the Message Channel, which is also used for normal communications. Q35. Is there any restriction on capacity of the SD card? SD HC card can be also used. As for the SD card having capacity of greater than 2G, the SD card needs to be formatted at the Terminal unit. The SD card having the size greater than 2G can be used, but capacity is limited to 2G. Q36. Where can DNID are checked? 4-38 DNID can be checked in [Reports] -> 4.Data Network ID. If DNID is enabled, the DNID where the "*" mark is provided at "Act" is enabled. Q37. Is it possible to loop back the SSAS message? Summary - 5 Loop back operation is available. Set Special for Destination Type, and then enter the code "91," which is looped back to Destination. Q38. Can the result of Diagnostic Test be stored on the SD card? 8-42 Select [Setup] -> 8.Configuration -> 6.Export/Import -> Export to SD, and then select "7. Test.".

9-5 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Chapter 9. Q & A

Q39. The error message "EEPROM ERROR" appears. 3-3, 3-8 EEPROM may be broken. When ordering EEPROM, report the serial number. Q40. Although IMN is set for FELCOM 18, IMN does not appear on the PC terminal. Since the IMN set for FELCOM 18 is not reflected on the PC terminal, IMN needs to be set individually. Q41. Can IC-315 and IC-318 on Junction Box use commonly? IC-315 and IC-318 are the basically the same. #6 and 7 on IC-315 are equivalent to RD-A and RD-B. As for IC-318, ALM-H and ALM-C are used. Since wiring between 15-pin D-sub and IC-315 or IC-318 is the same, IC-315 and IC-318 can be used. Q42. Calculation of Frequency from Channel The MES operates in the TX frequency, 1626.5 MHz to 1646.5 MHz/5 kHz step and the RX frequency, 1537.0 MHz to 1544.2 MHz/5 kHz step. Tx Frequency (MHz)=1626.5 + 0.0025(Xch－6000) Tx: 6000 ch -> 1626.500MHz Rx Frequency (MHz)=1530.0 + 0.0025(Xch－8000) Rx: 8000 ch -> 1530.000MHz

9-6 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Appendix 2. Specifications Appendix 2. Specifications AP2.1 FELCOM 18 AP2.1.1 GENERAL 1.1 Transmitting frequency 1.2 Receiving frequency 1.3 Channel interval 1.4 G/T 1.5 EIRP 1.6 Modulation 1.7 Modulation rate 1.8 Coding

1.11 EGC receiver 1.12 LRIT function

1626.5 to 1646.5 MHz 1537.0 to 1544.2 MHz 5 kHz Better than -23 dB/K (elevation angle 5°) 12 to 16 dBW (elevation angle 5°) BPSK 600/1200 sps Convolution with coding rate 1/2 and constraint length 7 Viterbi decoder IEC61162-1 Ed.3/4, Internal GPS Board (option) BWC, BWR, DBT, DTM, GGA, GLL, GNS, GSA, MTW, RMA, RMB, RMC, VDO, VDR, VTG, WPL, ZDA Built in (EGC: Enhanced Group Call) Standard

AP2.1.2 ANTENNA UNIT 2.1 Antenna type 2.2 Receiving gain 2.3 Receiving NF

Daisy loop antenna 33 to 40 dB 1.7 dB or less

2.4 Transmitting gain 2.5 Polarization 2.6 Axial ratio 2.7 VSWR

28.5 to 42.5 dB Right-hand circular polarization Within 6 dB (5° to 90°) 2.0 or less (50 ohm)

AP2.1.3 TERMINAL UNIT 3.1 Display 3.2 Brilliance 3.3 Visible distance

10.4” color TFT LCD, 800 x 600 dots (SVGA) 11 steps 0.7 m nominal

1.9 Decoding 1.10 Nav data interface Input data sentences

AP2-1 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Appendix 2. Specifications

AP2.1.4 POWER SOURCE 4.1 Terminal unit 4.2 Printer (PP-510, option) 4.3 AC/DC power supply unit PR-240 (option)

12-24 VDC: 8.0-4.0 A (Transmitting), 1.0-0.5 A (Receiving) 24 VDC: 1.5 A max. 100-115/200-230 VAC, 1 phase, 50/60 Hz, 24 VDC from battery

AP2.1.5 ENVIRONMENTAL CONDITION 5.1 Ambient temperature Exposed equipment -35°C to +55°C (storage: -35°C to +70°C) Protected equipment -15°C to +55°C 5.2 Relative humidity 95% or less at 40°C 5.3 Degree of protection Antenna unit IP56 Terminal unit IP22 (Option) Printer/Keyboard IPX0 Others IP22 (bulkhead mount) 5.4 Vibration IEC 60945 Ed.4 AP2.1.6 UNIT COLOR 6.1 Antenna unit Upper: N9.5, Lower: 2.5PB3.5/10 6.2 Terminal unit/Junction box N2.5 6.3 Others 2.5GY5/1.5

AP2-2 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Appendix 2. Specifications

AP2.2 FELCOM 19 AP2.2.1 GENERAL 1.1 Transmitting frequency 1.2 Receiving frequency 1.3 Channel interval 1.4 G/T 1.5 EIRP 1.6 Modulation 1.7 Modulation rate 1.8 Coding 1.9 Decoding 1.10 Nav data interface Input data sentences

1626.5 to 1646.5 MHz 1537.0 to 1544.2 MHz 5 kHz Better than -23.7 dB/K (elevation angle 5°) 7 to 16 dBW (elevation angle 5°) BPSK 600/1200 sps Convolution with coding rate 1/2 and constraint length 7 Viterbi decoder IEC61162-1 Ed.3/4, Internal GPS Board BWC, BWR, DBT, DTM, GGA, GLL, GNS, GSA, MTW, RMA, RMB, RMC, VDO, VDR, VTG, WPL, ZDA

AP2.2.2 ANTENNA UNIT 2.1 Antenna type 2.2 Receiving gain 2.3 Receiving NF 2.4 Transmitting gain 2.5 Polarization

Daisy loop antenna 33 to 40 dB 1.7 dB or less 26 to 40 dB Right-hand circular polarization

2.6 Axial ratio 2.7 VSWR

Within 6 dB (5° to 90°) 2.0 or less (50 ohm)

AP2.2.3 POWER SOURCE 3.1 Communication unit 3.2 AC/DC power supply unit PR-240 (option)

12-24 VDC: 3.8-1.9 A (Transmitting), 0.8-0.4 A (Receiving) 100-115/200-230 VAC, 1 phase, 50/60 Hz, 24 VDC from battery

AP2-3 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Appendix 2. Specifications

AP2.2.4 ENVIRONMENTAL CONDITION 4.1 Ambient temperature Exposed equipment -35°C to +55°C (storage: -35°C to +70°C) Protected equipment -15°C to +55°C 4.2 Relative humidity 95% at 40°C 4.3 Degree of protection Antenna unit IP56 Communication unit IP22(tabletop/bulkhead mount) Others IP22 (bulkhead mount) 4.4 Vibration Inmarsat SDM LPSES standard AP2.2.5 UNIT COLOR 5.1 Antenna unit 5.2 Communication unit/Junction box 5.3 Others

Upper: N9.5, Lower: 2.5PB3.5/10 N2.5 2.5GY5/1.5

AP2-4 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Appendix 1. Event list

31042 31043 31044 31045 31046 31047

31048

31097 31098 31099 31101 31102 31103 31104 31105 31106 31107

31108

31109 31110 32001 32002

32003

Ignored: MES is not idle. (MES is not idle) Ignored: Now receiving EGC message. (Now receiving EGC message) Ignored: MES is not Login. Please operate Login. (MES is not Login. Please operate Login) Ignored: Current Network is restoration mode. (Current Network is restoration mode) Ignored: NCS Common Channel Failure. (NCS Common Channel Failure) Can’t deliver mail to server. Starting PV Test Process. Automatic test mode: Normal communication disabled. Do not press any distress button unless you are in distress." (Starting PV Test Process) PV TEST is completed. PV TEST is failed. PV TEST is aborted. MES Signaling Failure, during PV TEST. Receiving Test Failure, Timeout while waiting on NCS CC. (Receiving Test Failure) Sending Test Failure, Too many retries. (Sending Test Failure) PV TEST is aborted by LES PV TEST is pending by LES PV TEST is rejected by LES PV TEST aborted because of RESTORATION mode. (PV TEST aborted for RESTORATION mode) Please activate Distress Alert TEST within 2 min. (Please activate Distress Alert TEST) TIMEOUT!! Distress Alert Test is automatically activated. (Distress Test is automatically activated) Can’t delivery a mail to server. WARNING: Memory Full for receive message. (Memory Full for receive message) WARNING: Cannot enter new DNID. Memory full for DNIDs. (Cannot enter new DNID) WARNING: Cannot enter new ENID. Memory full for ENIDs (Cannot enter new ENID)

MES busy Receiving the EGC message MES is not logged in. The Network is in Restoration Mode. Failure of NCS CC Failure of transmission to Mail Server

Activation of the PV test

Completion of the PV test Failure of the PV test Cancellation of the PV test Failure of MES Signaling Failure of the receiving test Failure of the sending test Cancellation of the PV test by LES Pending of the PV test by LES Rejection of the PV test by LES Abortion of PV Test in Restoration Mode

Distress Alert TEST

Distress Alert TEST Failure of transmission to Mail Server Memory for received messages is full. Memory for DNID is full.

Memory for ENID is full.

AP1-5 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Appendix 1. Event list

32004

32005 32006 32007

WARNING: Message received for DTE1 PORT. Please turn on DTE port equipment. (Message received for DTE1 PORT) WARNING: Message received for DTE2 PORT. Please turn on DTE port equipment. (Message received for DTE2 PORT) WARNING: Internal GPS UNIT failure. (Internal GPS UNIT failure) WARNING: External NAV equipment failure. (External NAV equipment failure)

41111 41112 41113

WARNING: Synchronization loss. Please change EGC channel. (EGC Synchronization loss) WARNING: Synchronization loss. Please check the current ocean region. (Synchronization loss) WARNING: BBER over 80%. Scanning NCS start manually. (BBER over 80%) WARNING: Can not find NCS CC in preferred region. Scanning all region is started. (Can not find NCS CC in preferred region) WARNING: Cannot find NCS CC in all region. Scanning is continued. (Cannot find NCS CC in all region) Data Report Program Updated Received Poll Command Successful Data Report Sending.

41114

Data Report failed, unauthorized DNID.

41115

Data Report failed, MES is not login.

41116

Data Report failed, selected LES not exist in current region. (Data Report failed, no LES in OR)

41117

Data Report failed, TDM LOST.

32008

32009

32010

32011

32012

41118 41119

MES Signaling Failure, Data Report failed. (DR failed, signaling failure) Reserved access failure, trying unreserved access. (Reserved access failure)

Transferring the received message to DTE1 is unable. Transferring the received message to DTE2 is unable. Failure of Internal GPS (detection of internal GPS signal is lost.) Failure of External Nav (detection of navigation data from external navigation system is lost.) Failure of synchronization (Sync) of EGC channel Failure of synchronization (Sync) of NCS CC Error rate of BBER (Bulletin Board Error Rate) is greater than 80%. Failure of scanning in the current ocean region Failure of scanning in all regions

Success of transmission of Data Report Failure of transmission of Data Report due to use of invalid DNID Failure of transmission of Data Report due to non-logged-in state Failure of transmission of Data Report due to selection of LES, which is not present in the current ocean region Failure of transmission of Data Report due to TDM LOST Failure of MES Signaling Failure of reserved access

41120

Data Report aborted.

Abortion of transmission of Data Report

41121

Data Report failed too long report.

41122

Successful Poll Acknowledgement Sending.

41123

Poll Acknowledgement Sending failed.

Failure of transmission of Data Report Success of transmission of Poll Acknowledgment Failure of transmission of Poll Acknowledgment

AP1-6 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Appendix 1. Event list

41124 41125 41126 41127 51001

51002

51003

51004

51005

Successful Data Report Programming by Polling. (Successful DR Programming) Data Report Programming failure by Polling, invalid parameters. (DR Programming failure by Polling) Data Report Program has been initiated by Polling. Data Report Program has been stopped by Polling.

51080 51081

Distress Alert completed.

51082

Distress Alert Test completed.

51083

Distress Alert Test aborted.

51084

Distress Alert Test failed.

51007 51008

51091 51092 51095

Failure of Data Report program by Polling Initiation of Data Report program by Polling Stop of Data Report program by Polling

Failure of transmission of Distress Alert Distress Alert not sent to LES, trying to use NCS. after initiation of transmission of Distress (Distress Alert not sent to LES) Alert to LES - Failure of transmission of Distress Alert Distress Alert not sent to NCS. NCS scanning is after initiation of transmission of Distress started Alert to LES - Failure of transmission of Distress Alert (Distress Alert not sent to NCS) to NCS - Failure of transmission of Distress Alert after initiation of transmission of Distress Distress Alert not sent to NCS. Distress Alert Alert to LES abandoned, Please re-send Distress Alert. - Failure of transmission of Distress Alert to NCS (Distress Alert sig fail) - Failure of transmission of Distress Alert to NCS in other ocean region Timeout! Distress Alert not acknowledged. Failure of reception of Distress Distress Alert abandoned, Please re-send Acknowledgement after transmitting the Distress Alert. Distress Alert. Abortion of transmission (Distress Alert not acknowledged) Acceptance of interruption of Distress DISTRESS ALERT interrupt accepted. Alert Timeout! Distress Test not acknowledged. (Distress Test not acknowledged) MES Signaling Failure, Distress Alert Test not sent. (Distress Test failed, signaling failure) Low-Power-C mode does not supply Distress Call. (LP-C mode does not supply Distress Call) Distress Alert activated.

51006

Success of Data Report program by Polling

Timeout! Distress Acknowledgement not received. Scanning NCS started automatically. (Distress Acknowledgement not received) Distress Alert aborted. Pre-set LES ID for DISTRESS ALERT is invalid in this ocean. Please input preferred LES ID in the menu. (Pre-set LES ID is invalid in this ocean)

Failure of reception of acknowledgment for Distress Alert test Failure of MES Signaling Transmission of Distress Alert using MINI-C is impossible. Activation of transmission of Distress Alert Completion of transmission of Distress Alert Activation of transmission of Distress Alert test Abortion of transmission of Distress Alert test Failure of transmission of Distress Alert test Failure of reception of Distress Acknowledgement Abortion of transmission of Distress Alert There is no LES ID set for Distress Alert in ocean region.

AP1-7 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Appendix 1. Event list

61054 61055

Timeout! LES response not received. (LES response not received) Successful Sending message to LES. Sending message failed. Sending message aborted. Sending message aborted by LES LES protocol error detected, Invalid Assignment. (LES protocol error detected) Call rejected by LES Call pending by LES

61056

Selected LES not exist in current region.

61001 61049 61050 61051 61052 61053

61060

MES Signaling Failure, during sending message. (Sending message failed, signaling failure) Awaiting message transfer. Message sending failure, unauthorized DNID LES_ID pares. (Message sends fail, unfaith DNID) Successful Delivery Status Request.

61061

Delivery Status Request is failed.

61062

Delivery Status Request is aborted.

61057 61058 61059

71069 81001

MES Signaling Failure, Delivery Status Request not sent. (Status request not sent, signaling failure) Successful Receiving message. Receiving message failed. Receiving message aborted. MES Signaling Failure, during receiving message. (Message Rx failed, signaling failure) Receiving message aborted by LES DHCP server not exists.

81002

Sorry, system busy now.

81003

Current LES out of service area.

81004 81005 81006 81007

No target address. Too many addresses. Send message type mismatch. Send massage parameter mismatch.

81008

Illegal address.

81009

Mail data abnormal.

81010

Data size too large.

81011

Your address access denied.

91001

Can't enter in Print Que.

61063 71065 71066 71067 71068

There is no response from LES. Success of message transmission Failure of message transmission Abortion of message transmission Abortion of message transmission by LES Detection of LES protocol error Rejection of call by LES Pending of call by LES There is no destination LES in the ocean region. Failure of MES Signaling While sending message Failure of message transmission and invalid DNID LES ID pair Success of reception of delivery status Failure of transmission of delivery status request Abortion of transmission of delivery status request Failure of MES Signaling and failure of transmission of delivery status request Success of reception of message Failure of reception of message Abortion of reception of message Failure of MES Signaling Abortion of reception of message by LES There is no DHCP server. Message for "waiting transmission" is full in the system. The currently selected LES does not exist in the current ocean region. Destination address is not set. Excess of number of destinations Message type error Address parameter error Characters that cannot be used in the destination address/ domain name abnormality Mail header abnormality Excess of the maximum transmission size set for Send Limit Size at Mail Gateway Transmission from PC on which transmission is disabled Entry into the print queue is unable.

AP1-8 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Appendix 1. Event list

91002 91003 91004

Print Que is Full. Can't print. PRINTER NOT READY. Can't print. Paper Low.

91005

Disk full. Can't enter in Print Que.

Print queue is full. Printer is not connected. Paper-out condition on the printer Entry into the print queue is impossible due to full disk.

AP1-9 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Appendix 2. Specifications Appendix 3. Specifications AP2.1 FELCOM 18 AP2.1.1 GENERAL 1.1 Transmitting frequency 1.2 Receiving frequency 1.3 Channel interval 1.4 G/T 1.5 EIRP 1.6 Modulation 1.7 Modulation rate 1.8 Coding

1.11 EGC receiver 1.12 LRIT function

1626.5 to 1646.5 MHz 1537.0 to 1544.2 MHz 5 kHz Better than -23 dB/K (elevation angle 5°) 12 to 16 dBW (elevation angle 5°) BPSK 600/1200 sps Convolution with coding rate 1/2 and constraint length 7 Viterbi decoder IEC61162-1 Ed.3/4, Internal GPS Board (option) BWC, BWR, DBT, DTM, GGA, GLL, GNS, GSA, MTW, RMA, RMB, RMC, VDO, VDR, VTG, WPL, ZDA Built in (EGC: Enhanced Group Call) Standard

AP2.1.2 ANTENNA UNIT 2.1 Antenna type 2.2 Receiving gain 2.3 Receiving NF

Daisy loop antenna 33 to 40 dB 1.7 dB or less

2.4 Transmitting gain 2.5 Polarization 2.6 Axial ratio 2.7 VSWR

28.5 to 42.5 dB Right-hand circular polarization Within 6 dB (5° to 90°) 2.0 or less (50 ohm)

AP2.1.3 TERMINAL UNIT 3.1 Display 3.2 Brilliance 3.3 Visible distance

10.4” color TFT LCD, 800 x 600 dots (SVGA) 11 steps 0.7 m nominal

1.9 Decoding 1.10 Nav data interface Input data sentences

AP2-1 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Appendix 3. Specifications

AP2.1.4 POWER SOURCE 4.1 Terminal unit 4.2 Printer (PP-510, option) 4.3 AC/DC power supply unit PR-240 (option)

12-24 VDC: 8.0-4.0 A (Transmitting), 1.0-0.5 A (Receiving) 24 VDC: 1.5 A max. 100-115/200-230 VAC, 1 phase, 50/60 Hz, 24 VDC from battery

AP2.1.5 ENVIRONMENTAL CONDITION 5.1 Ambient temperature Exposed equipment -35°C to +55°C (storage: -35°C to +70°C) Protected equipment -15°C to +55°C 5.2 Relative humidity 95% or less at 40°C 5.3 Degree of protection Antenna unit IP56 Terminal unit IP22 (Option) Printer/Keyboard IPX0 Others IP22 (bulkhead mount) 5.4 Vibration IEC 60945 Ed.4 AP2.1.6 UNIT COLOR 6.1 Antenna unit Upper: N9.5, Lower: 2.5PB3.5/10 6.2 Terminal unit/Junction box N2.5 6.3 Others 2.5GY5/1.5

AP2-2 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Appendix 3. Specifications

AP2.2 FELCOM 19 AP2.2.1 GENERAL 1.1 Transmitting frequency 1.2 Receiving frequency 1.3 Channel interval 1.4 G/T 1.5 EIRP 1.6 Modulation 1.7 Modulation rate 1.8 Coding 1.9 Decoding 1.10 Nav data interface Input data sentences

1626.5 to 1646.5 MHz 1537.0 to 1544.2 MHz 5 kHz Better than -23.7 dB/K (elevation angle 5°) 7 to 16 dBW (elevation angle 5°) BPSK 600/1200 sps Convolution with coding rate 1/2 and constraint length 7 Viterbi decoder IEC61162-1 Ed.3/4, Internal GPS Board BWC, BWR, DBT, DTM, GGA, GLL, GNS, GSA, MTW, RMA, RMB, RMC, VDO, VDR, VTG, WPL, ZDA

AP2.2.2 ANTENNA UNIT 2.1 Antenna type 2.2 Receiving gain 2.3 Receiving NF 2.4 Transmitting gain 2.5 Polarization

Daisy loop antenna 33 to 40 dB 1.7 dB or less 26 to 40 dB Right-hand circular polarization

2.6 Axial ratio 2.7 VSWR

Within 6 dB (5° to 90°) 2.0 or less (50 ohm)

AP2.2.3 POWER SOURCE 3.1 Communication unit 3.2 AC/DC power supply unit PR-240 (option)

12-24 VDC: 3.8-1.9 A (Transmitting), 0.8-0.4 A (Receiving) 100-115/200-230 VAC, 1 phase, 50/60 Hz, 24 VDC from battery

AP2-3 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Appendix 3. Specifications

AP2.2.4 ENVIRONMENTAL CONDITION 4.1 Ambient temperature Exposed equipment -35°C to +55°C (storage: -35°C to +70°C) Protected equipment -15°C to +55°C 4.2 Relative humidity 95% at 40°C 4.3 Degree of protection Antenna unit IP56 Communication unit IP22(tabletop/bulkhead mount) Others IP22 (bulkhead mount) 4.4 Vibration Inmarsat SDM LPSES standard AP2.2.5 UNIT COLOR 5.1 Antenna unit 5.2 Communication unit/Junction box 5.3 Others

Upper: N9.5, Lower: 2.5PB3.5/10 N2.5 2.5GY5/1.5

AP2-4 CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

Only IC-305 DｶﾊﾞｰLｸﾐﾋﾝ DISTRESS BUTTON COVER ASSY. 05-073-1111-0 (100-274-720-10)

ｷｰｼｰﾄ KEY SHEET

IC-305 IC-306

ｹｰｽ(ｳｴ) CASE(TOP)

IC-306

+ﾊﾞｲﾝﾄﾞｺﾈｼﾞ BINDING HEAD SCREW M3X8 C2700Wﾎﾟﾘｼｰﾙ (000-163-651-10)

16-018-4001-2 (100-300-922-10) 16-018-5001-3 (100-301-013-10)

AL

IC-305

+-ﾅﾍﾞｾﾑｽB WASHER HEAD SCREW *B* M3X8 C2700W MBNI2 (000-163-190-10)

N FI D

EN

ｹｰﾌﾞﾙｵｻｴ(3) CABLE CLAMP(3) 16-018-4006-1 (100-300-971-10)

TI

ｵﾝｱﾂﾖｸｾｲｼｰﾙ VOLUME CONTROL SEAL 16-018-4008-1 (100-303-831-10)

ｹｰﾌﾞﾙｵｻｴ(2) CABLE CLAMP(2) 16-018-4005-0 (100-300-960-10)

16-018-4102-4 (100-301-004-10) 16-018-5102-4 (100-301-034-10)

※ DIST/RCV 1 PCB

+-ﾅﾍﾞｾﾑｽB WASHER HEAD SCREW *B* M4X12 C2700W MBNI2 (000-163-192-10)

ｹｰｽ(ｼﾀ) CASE(BOTTOM)

O

※

C

ｹｰﾌﾞﾙｵｻｴ(1 CABLE CLAMP(1) 16-018-4004-0 (100-300-950-10)

※

組合せ互換表 Combination of DIST/RCV 1 PCB and CASE(BOTTOM)

ｹｰｽ(ｼﾀ) CASE(BOTTOM)

MODEL

IC-306

IC-305

DIST/RCV 1 PCB

16P0213A(LF) 16P0213C(LF) (004-655-610-00) (001-062-600-00)

16P0213B(LF) (004-655-630-00)

16P0213D(LF) (001-062-630-00)

新 NEW

16-018-4002-2 (100-300-932-10)

○

○

○

○

旧 OLD

16-018-4002-1

○

×

○

×

FELCOM 15

FELCOM 18

RC-1800F/T RC-1800F2 APPROVED

CHECKED

DRAWN

29 Nov.2012

28 Nov.2012

28 Nov.2012

W.Katsube

T.Yoshida

A.Yabuta

UNIT

IC-305

遭難警報器

DISTRESSALT/RECCALLUNIT

IC-306

アラームユニット

ALARM UNIT

DWG.NO. C5635-E03-D

CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

+ﾊﾞｲﾝﾄﾞｾﾑｽF BINDER HEAD SCREW-F M4X10 C2700W MBCR2 (000-163-543-10)

ｶﾊﾞｰ COVER 16-023-5516-2 (100-373-582-10)

ｱｰｽﾏｰｸ EARTH LABEL 24-005-5013-1 (100-332-171-10) ﾀﾝｼﾀﾞｲ TERMINAL BOARD 264-321-15P (000-146-183-11)

AL

ﾊﾘﾏｰｸ(318) LABEL(318) 16-023-5512-1 (100-373-561-10)

TI

+-ﾅﾍﾞｾﾑｽB WASHER HEAD SCREW *B* M4X20 C2700W MBNI2 (000-163-195-10)

ｹｰﾌﾞﾙｵｻｴ(2) CABLE CLAMP(2) 16-018-6005-2 (100-301-072-10)

EN

+-ﾅﾍﾞｾﾑｽB WASHER HEAD SCREW *B* M4X8 C2700W MBNI2 (000-163-200-10)

N FI D

ﾌﾞﾗｲﾝﾄﾞｺﾞﾑ BLIND RUBBER 16-018-6004-2 (100-301-062-10)

+-ﾅﾍﾞｾﾑｽB WASHER HEAD SCREW *B* M4X10 C2700W MBNI2 (000-163-191-10) ｱｯﾁｬｸﾀﾝｼ CRIMP-ON LUG FV1.25-4(LF) RED (000-166-666-10)

ｹｰﾌﾞﾙｵｻｴ(1) CABLE FIXTURE (1) 16-023-5517-0 (100-373-590-10)

+ﾅﾍﾞｺﾈｼﾞ PAN HEAD SCREW M4X20 C2700W MBNI2 (000-163-439-10)

O

ｹｰｽ CASE 16-023-5515-1 (100-373-571-10)

C

ｿﾄﾊﾊﾂｷｻﾞｶﾞﾈ EXTERNAL TOOTH LOCK WASHER M4 C5191W MBNI2 (000-168-312-10)

ﾛｯｶｸﾅｯﾄ 1ｼｭ HEXAGONAL NUT 1 SYU M4 C3604B MBNI2 (000-168-237-10)

ﾐｶﾞｷﾋﾗｻﾞｶﾞﾈ FLAT WASHER M4 C2680R MBNI2 (000-168-235-10)

ﾁｮｳﾅｯﾄ 2ｼｭ WING NUT M4 SWCH10R MFNI2 (000-169-556-10)

ｺｳｻﾞｲ INSTALLATION MATERIALS CP16-05101 +ﾄﾗｽﾀｯﾋﾟﾝﾈｼﾞ1ｼｭ SELF TAPPING SCREW 4X16 SUS304 (000-162-605-10)

ﾊﾞﾈｻﾞｶﾞﾈ SPRING WASHER M4 C5191W MBNI2 (000-168-238-10)

MODEL

ｹｰﾌﾞﾙ(ｸﾐﾋﾝ) CABLE ASSEMBLY 17JE-SPMCU-L2000 (000-146-178-13)

4

FELCOM18 FELCOM19

APPROVED

CHECKED

DRAWN

21 Nov.2012

21 Nov.2012

29 Oct.2012

W.Katsube

T.Yoshida

A.Yabuta

UNIT

IC-318

接続箱 JUNCTION BOX

DWG.NO. C5674-E03-A

CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

ﾄﾞｰﾑ ANTENNA DOME 16-018-1001-3 (100-297-963-10)

ｱﾝﾃﾅｴﾚﾒﾝﾄ ANTENNA ELEMENT ASSEMBLY IC-118 (001-193-660-00)

AL

IC-119 (001-193-670-00)

ANT RFﾌﾟﾘﾝﾄ

ANTｹｰｽ ANTENNA RF MODULE

IC-118 16P0285(LF)

IC-118 (001-193-680-00)

TI

IC-119 16P0286(LF)

IC-119 (001-193-690-00)

ﾃﾐｯｼｭ TEMISH S-NTF1033-K02-J (000-169-628-10)

EN

ﾄﾞｰﾑﾊﾟﾂｷﾝ DOME GASKET 16-018-1102-0 (100-298-010-10)

N FI D

ANTｹｰｽ ANT CASE 16-023-2511-1

ｱﾝﾃﾅﾀﾞｲ ANTENNA BASE ASSEMBLY IC-115/116 (004-439-620-00)

ANTﾀﾞｲﾊﾟﾂｷﾝ GASKET 16-018-1204-0 (100-302-120-10)

C

O

ANTﾀﾞｲ ANTENNA STAND 16-018-1201-3

ﾈｼﾞﾖｳﾊﾟﾂｷﾝ GASKET 16-018-1203-0 (100-298-100-10)

ﾌｿﾞｸﾋﾝ ACCESSORIES FP16-02501 ｹﾐｼｰﾙ SILICON RUBBER S-8400W ｱﾙﾐﾁｭｰﾌﾞ50G (000-158-483-10) ｲﾗｯｸｽｽﾘｰﾌﾞ SCM2 INSULATION SLEEVE 07-1220 ｸﾛ *40MM* (000-165-300-10) ｺﾝﾍﾞｯｸｽ CABLE TIE CV-450B (000-173-169-10)

+ｱﾌﾟｾｯﾄUIｾﾑｽB UPSET UI SCREW-B M5X10 SUS304 (000-163-757-10)

ANTﾀﾞｲﾄﾒﾈｼﾞ ANTENNA FIXING SCREW 16-018-1202-0 (100-298-090-10)

1

5

ｹｰﾌﾞﾙﾎｺﾞｻﾞｲ

ﾛｯｸﾅｯﾄｸﾐﾋﾝ LOCK NUT ASSEMBLY CP16-05501 (001-192-280-00)

MODEL

1

CABLE PROTECTION MATERIAL

16-018-1251-1 (100-298-111-10)

1

FELCOM18 FELCOM19

APPROVED

CHECKED

DRAWN

21 Nov.2012

21 Nov.2012

25 Oct.2012

W.Katsube

T.Yoshida

A.Yabuta

UNIT

IC-118/119

ｱﾝﾃﾅﾕﾆﾂﾄ ANTENNA UNIT

DWG.NO. C5674-E02-A

CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

J7

J5

J4

J3

J1

(P)PWR-C 16P0227B

SW-PHｺﾈｸﾀ SW-PH CONNECTOR ASSEMBLY 16-200(ｽｲｯﾁ-3P) (001-193-920-00)

(000-021-832-00)

E

ﾏｴﾊﾟﾈﾙ FRONT PANEL 16-023-4501-0 (100-368-060-10)

C

O ﾊﾟﾈﾙﾊﾟｯｷﾝ PANEL GASKET 16-018-2015-2 (100-297-892-10)

F

N

+-ﾅﾍﾞｾﾑｽA WASHER HEAD SCREW *A* M3X15 C2700W MBCR2 (000-163-159-10)

CHECKED 21 Nov.2012

T.Yoshida

21 Nov.2012

W.Katsube

DRAWN

A.Yabuta

IC-219

ﾋｭｰｽﾞ GLASS TUBE FUSE FGBO 125V 10A PBF (000-155-826-10)

ﾋｭｰｽﾞ GLASS TUBE FUSE FGBO-A 125V 5A PBF (000-155-853-10)

1

2

ﾏｸﾂｷｸﾞﾛﾒｯﾄ GROMMET MG-15 (000-166-458-10) LANｶﾊﾞｰ LAN COVER 16-023-4507-0 (100-368-090-10)

1

1 ﾋｭｰｽﾞﾊﾘﾏｰｸ FUSE LABEL 03-153-1312-0 (100-292-140-10)

ﾋｭｰｽﾞ GLASS TUBE FUSE FGBO-A 125V 5A PBF (000-155-853-10)

2

3

ｺﾝﾍﾞｯｸｽ CABLE TIE CV-100N (000-162-167-10) +ﾄﾗｽﾀｯﾋﾟﾝﾈｼﾞ SELF TAPPING SCREW 4X40 SUS304 (000-162-606-10)

1

1

1

1

ｹｰﾌﾞﾙ(ｸﾐﾋﾝ)MJ CABLE ASSEMBLY MJ-A3SPF0016-035C (000-154-024-10)

ｱｰｽﾊﾞﾝ COPPER STRAP 05-003-0031-0 (590-300-310-10)

ｺｳｻﾞｲ INSTALLATION MATERIALS CP16-05301

ﾖﾋﾞﾋﾝ SPARE PARTS SP16-01401

ﾌｿﾞｸﾋﾝ ACCESSORIES FP16-02700 (000-021-833-00)

通信制御ﾕﾆｯﾄ COMMUNICATION UNIT DWG.NO. C5675-E01-A

UNIT

FETｵｻｴｺﾞﾑ FET FIXING RUBBER 16-018-2023-1 (100-297-921-10)

RF CONﾌﾟﾘﾝﾄ PRINTED CIRCUIT BOARD 16P0284B(LF) (001-193-910-00)

26 Oct.2012

FELCOM19 APPROVED

MODEL

FETｵｻｴｲﾀ FET FIXING PLATE 16-018-2021-1 (100-297-901-10)

ｹｰｽ(ｼﾀ) CASE (LOWER) 16-023-4509-1 (100-373-681-10)

ｽﾍﾟｰｻ SPACER SQ-14 (000-159-298-10)

ﾊﾟﾈﾙﾊﾟｯｷﾝ PANEL GASKET 16-018-2015-2 (100-297-892-10)

(P)COMM CPUｸﾐﾋﾝ COMM CPU PCB LESS ID-ROM/U7 IC-219 (001-194-120-00)

PWR-Cﾌﾟﾘﾝﾄ PRINTED CIRCUIT BOARD 16P0227B(LF) (001-193-900-00)

M4 C5191W MBNI2 (000-168-312-10)

EXTERNAL TOOTH LOCK WASHER

ｿﾄﾊﾊﾂｷｻﾞｶﾞﾈ

+ﾅﾍﾞｺﾈｼﾞ PAN HEAD SCREW M4X20 C2700W MBNI2 (000-163-439-10)

L A

N M4 C3604B MBNI2 (000-168-237-10)

PW M4 C2680R MBNI2 (000-168-235-10)

I T N E ID

ｳｼﾛﾊﾟﾈﾙ BACK PANEL 16-023-4502-1 (100-373-611-10)

SW M4 C5191W MBNI2 (000-168-238-10)

ﾁｮｳﾅｯﾄ 2ｼｭ WING NUT M4 SWCH10R MFNI2 (000-169-556-10)

CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

(000-021-831-00)

J

(LESS ID-ROM) ﾂｳｼﾝｾｲｷﾞﾖﾕﾆﾂﾄ COMMUNICATION UNIT

PWR HICﾌﾟﾘﾝﾄ PRINTED CIRCUIT BOARD (HIC) 16P0224(LF) (004-655-580-00)

PWR HICﾌﾟﾘﾝﾄ PRINTED CIRCUIT BOARD (HIC) 16P0220(LF) (004-655-560-00)

PWRﾌﾟﾘﾝﾄ 16P0288(LF)

ｼｷﾘｲﾀ PARTITION PLATE 16-018-2016-2 (100-297-942-10)

ｹｲｺｸﾗﾍﾞﾙ(1) WARNING LABEL 1 86-003-1011-3 (100-236-233-10)

+ﾊﾞｲﾝﾄﾞｾﾑｽF BINDER HEAD SCREW-F M3X10 C2700W (000-176-754-10)

ｹｰｽ(ｳｴ) CASE (UPPER) 16-023-4508-1 (100-373-671-10) +ﾊﾞｲﾝﾄﾞｺﾈｼﾞ BINDING HEAD SCREW M3X6 SWCH (000-176-673-10)

PWR HICﾌﾟﾘﾝﾄ PRINTED CIRCUIT BOARD 16P0290(LF) (001-193-720-00)

PWR HICﾌﾟﾘﾝﾄ PRINTED CIRCUIT BOARD (HIC) 16P0291(LF) (001-193-890-00)

ﾎｳﾈﾂｼｰﾄ HEAT SINK RUBBER 16-018-2022-0 (100-297-910-10)

ROCKER SWITCH

16-200(ｽｲｯﾁ-3P) (001-193-920-00)

PWR HICﾌﾟﾘﾝﾄ PRINTED CIRCUIT BOARD (HIC) 16P0222A(LF) (001-193-880-00)

(P)PWRｾｯﾄﾋﾝ PRINTED CIRCUIT BOARD IC-219 16P0288 (001-194-110-00)

16-198(4-4P) (001-179-930-00)

J2

GPS

(P)COMM CPU 16P0282

(P)PWR 16P0288 J2

16-197(10-10P) (001-179-920-00)

J5

(P)RF CON 16P0284B

J6

16-199(4-5P) (001-179-940-00)

J4

SML2SC30-4X30ADP.5S4 (000-176-304-10)

J3

ｺﾈｸﾀ(ｸﾐﾋﾝ) CONNECTOR ASSEMBLY

ｺｳｻﾞｲ INSTALLATION MATERIALS CP16-05202 ﾌｧｽﾅｰ(3) HOOK LOOP FASTERNER 16-007-6814-0 (100-237-670-10)

1

1

ﾌｧｽﾅｰ(4) HOOK LOOP FASTENER 16-007-6815-0 (100-237-680-10)

1

ﾊﾘﾏｰｸ LABEL 16-023-3552-0 (100-373-800-10)

LANｹｰﾌﾞﾙｻｻｴ LAN CABLE SUPPORTING 16-023-3532-0 (100-369-610-10) LANﾖｳｽﾎﾟﾝｼﾞ SPONGE FOR LAN 16-023-3533-0 (100-369-620-10)

1

+ﾄﾗｽﾀｯﾋﾟﾝﾈｼﾞ1ｼｭ SELF-TAPPING SCREW 5X20 SUS304 (000-162-608-10)

ﾀ-ﾐﾅﾙﾕﾆﾂﾄ TERMINAL UNIT

4

ｺﾝﾍﾞｯｸｽ CABLE TIE CV-150B (000-167-183-10)

2

ﾋｭｰｽﾞ GLASS TUBE FUSE FGBO 125V 7A PBF (000-155-831-10)

ﾋｭｰｽﾞ GLASS TUBE FUSE FGBO 125V 7A PBF (000-155-831-10)

1

GPSﾌﾟﾘﾝﾄ PCB GPS

4

1

1

ﾊﾟﾈﾙﾊﾟﾂｷﾝ PANEL GASKET 16-018-3003-1 (100-297-661-10)

LCD OT104ASDDLV-00 (000-176-234-10)

FETｵｻｴｺﾞﾑ FET FIXING RUBBER 16-018-3204-0

(P)TERMCPUｸﾐﾋﾝ TERMCPU PCB LESS ID-ROM/U20 IC-218 ﾌﾞｼｭﾂﾖｳ (001-193-990-00)

O

ﾗﾊﾞｰｷｰ RUBBER KEY 16-018-3005-1 (100-297-681-10)

C

ｺﾈｸﾀ(ｸﾐﾋﾝ) CONNECTOR ASSEMBLY

ﾊﾟﾈﾙ PANEL 16-023-3547-0

SD_USBﾊﾟﾈﾙ SD_USB PANEL 16-023-3511-2

J2

ﾃﾞｲｽﾄﾚｽﾌﾀ DISTRESS LID 05-085-1011-2

(P)TERMPWR 16P0287B

PWｼｰﾄ PW SHEET 16-023-3548-0

ﾃﾞｨｽﾄﾚｽﾌﾀﾌｸﾛﾂﾞﾒ DISTRESS KEY COVER (PACKED) HG-8800 (005-378-320-00)

SML2SC30-4X60ADP.5S4 (000-175-379-10) J11

J5

(P)PWR-C 16P0214A

CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

ﾎｳﾈﾂｲﾀ HEAT SINK 16-018-3201-0 +-ﾅﾍﾞｾﾑｽB WASHER HEAD SCREW *B* M3X15 C2700W MBNI2 (000-163-185-10)

ﾊﾝｶﾞｰ BRACKET ASSEMBLY IC-218-A/IB-585 (001-193-750-00)

ﾗｲﾅｰ LINER 03-112-1403-0 (100-159-490-10)

ﾉﾌﾞｸﾐﾋﾝ KNOB DCU12 (001-026-450-00)

ﾊﾝｶﾞｰﾜｯｼｬｰ BRACKET WASHER 05-029-0132-1 (100-087-911-10)

ﾊﾝｶﾞｰ BRACKET 16-023-3545-0

ﾉﾌﾞ(N2.5) KNOB(N2.5) 19-028-2073-1

J6

J12

J3

SML2SC30-4X50ADP.5S4 (000-176-303-10) to DGPS

MODEL

J7

FELCOM18

H.FL-LP-BNC-BJ L60 (000-146-253-10) J2

16-201(4-4P) (001-185-110-00)

ﾎｳﾈﾂﾎｷｮｳｲﾀ REINFORCEMENT FOR HEAT SINK 16-018-3207-1

(P)RF CON 16P0284A

J1 J3

+ﾊﾞｲﾝﾄﾞｺﾈｼﾞ BINDING HEAD SCREW M3X6 SWCH (000-176-673-10) ﾎｳﾈﾂｼｰﾄ HEAT SINK RUBBER 16-018-3202-0

TERMPWRﾌﾟﾘﾝﾄ 16P0287B(LF)

RF CONｸﾐﾋﾝ PRINTED CIRCUIT BOARD IC-218 (001-193-970-00)

51065-0700-PHR7-L110 (000-176-305-10)

J5

16-195(10-10P) (001-179-800-00)

ｶﾊﾞｰ COVER 16-023-3546-0

ｽﾍﾟｰｻ(2) SPACER (2) HSA-3025CDﾚｽ (000-168-902-10)

ｼｰﾙﾄﾞｲﾀ SHIELD PLATE 16-018-3103-3 (100-297-713-10)

J1 16P0246

16-173(9-9P) (004-439-510-00) J4

PWR-Cﾌﾟﾘﾝﾄ PRINTED CIRCUIT BOARD 16P0214A(LF) (001-193-710-00)

SWﾌﾟﾘﾝﾄ PRINTED CIRCUIT BOARD 16P0294(LF) (001-193-740-00)

(P)TERMCPU J7 16P0283B

(P)SD USB 16P0289 J1

ﾌﾞｻﾞｰｼｰﾄ BUZZER SHEET 16-023-3549-0

ﾃﾞｨｽﾄﾚｽﾋﾟﾝ DISTRESS PIN 05-085-1014-0

J5

DF1920-W-L70 (000-176-213-10)

J7

BINDING HEAD SCREW

M2.5X6 SUSXM7 (000-176-707-10)

LCD

J6

ﾃﾞﾝｹﾞﾝﾊﾘﾏｰｸ218 POWER LABEL 218 16-023-3551-0

ｹｲｺｸﾗﾍﾞﾙ(2) WARNING LABEL(2) 03-129-1001-3

+ﾊﾞｲﾝﾄﾞｺﾈｼﾞ BINDING HEAD SCREW M3X6 SWCH (000-176-673-10)

J13

+ﾊﾞｲﾝﾄﾞｾﾑｽF BINDER HEAD SCREW-F M3X8 C2700W MBCR2 (000-163-538-10)

ﾅｯﾄﾌﾞｻﾞｲ NUT PARTS 16-023-3539-0

PWR HICﾌﾟﾘﾝﾄ PRINTED CIRCUIT BOARD 16P0290(LF) (001-193-720-00)

(P)GPS J2

16-196(10-5,3,2P) (001-179-810-00) (P)SW J1 16P0294

FETｵｻｴｲﾀ FET FIXING PLATE 16-018-3203-2

SD USBﾌﾟﾘﾝﾄ PRINTED CIRCUIT BOARD 16P0289(LF) (001-193-730-00)

(P)SDﾄﾘﾂｹｲﾀ (P)SD FIXING PLATE 16-023-3514-0 (100-369-540-10)

SD_USBﾊﾟﾈﾙﾊﾟｯｷﾝ SD_USB PANEL PACKING 16-023-3512-0

ｼﾔﾌﾄﾎﾙﾀﾞｰ SHAFT HOLDER 05-085-1012-3

○

N FI D

1

SD_USBﾊﾟﾈﾙｸﾐﾋﾝ SD USB PANEL IC-218/IB-585 (001-194-000-00)

ﾃﾞｨｽﾄﾚｽﾊﾞﾈ DISTRESS SPRING 05-085-1013-0

IC-218-N-G (000-021-829-00)

RFｼｬｰｼ RF CHASSIS 16-023-3522-0 (100-369-570-10)

+ﾅﾍﾞｾﾑｽBK WASHER HEAD SCREW *BK* M2X6 C2700W MBNI2 (000-163-512-10)

FURUNOﾛｺﾞH3 FURUNO STICKER H3 19-028-1502-0

+ﾊﾞｲﾝﾄﾞｺﾈｼﾞ

×

ｺﾈｸﾀｲﾀ CONNECTOR PLATE 16-023-3523-0 (100-369-580-10)

ｼｬｰｼ CHASSIS 16-023-3521-0 (100-369-560-10)

ﾌｨﾙﾀｰ FILTER 16-018-3004-1

IC-218-N (000-021-828-00)

1

ﾌｿﾞｸﾋﾝ ACCESSORIES FP16-02600

ﾊﾟﾈﾙｸﾐﾋﾝ FRONT BEZEL WITH FILTER IC-218 (001-193-950-00)

TERMPWRｸﾐﾋﾝ TERMPWR ASSEMBLY IC-218 (001-193-980-00)

ﾖﾋﾞﾋﾝ SPARE PARTS SP16-01301 ﾋｭｰｽﾞ GLASS TUBE FUSE FGBO 125V 15A PBF (000-155-827-10)

ﾐﾆ ｷｰﾎﾞｰﾄﾞ KEYBOARD 5139U (000-176-235-10)

(LESS ID-ROM)

ﾌﾞﾗｲﾝﾄﾞｲﾀ SCREEN PLATE 16-023-3526-0

ｲﾁｷﾞﾒｺﾞﾑ POSITIONING RUBBER 16-023-3538-0

AL

ｱｰｽﾊﾞﾝ COPPER STRAP 05-003-0031-0 (590-300-310-10)

4

TI

ﾋｭｰｽﾞﾊﾘﾏｰｸ FUSE LABEL 03-153-1312-0 (100-292-140-10)

ｶﾊﾞｰｸﾐﾋﾝ REAR COVER ASSEMBLY IC-218 (001-193-960-00)

GPSﾌﾟﾘﾝﾄ PRINTED CIRCUIT BOARD 16P0246(LF) (004-656-540-00)

EN

ｺｳｻﾞｲ INSTALLATION MATERIALS CP16-05201

APPROVED

CHECKED

DRAWN

21 Nov.2012

21 Nov.2012

31 Oct.2012

W.Katsube

T.Yoshida

A.Yabuta

UNIT DWG.NO.

IC-218 C5674-E01-A

ﾀ-ﾐﾅﾙﾕﾆﾂﾄ TERMINAL UNIT

1

2

4

3

5

6

アラームユニット 1 2 3 4 5

P P

TP5FBAW-5DFBB,30m,φ7.7 DGPS

DGPSデコーダー DGPS DECODER

COAX. CABLE(50Ω)

BNC

USB

A TYPE キーボード KEYBOARD

24 VDC (+) ｱｶ RED (-) ｸﾛ BLK GND ｼﾛ WHT

B

3

*1

12 VDC

DC/DCコンバータ DC/DC CONVERTER

100-115/ *1 200-230 VAC DPYC-2.5 1φ,50/60Hz *1 24 VDC

17JE-23250 57-3036 -02(D8C) プリンタ 36 25 16S0184 PRINTER 3m,φ8 PP-510 *2 または OR H230817-1(*2) 防水仕様ケーブル WATERPROOF CABLE

MJ-A3SPF0018-050Z 5m,φ11

12-24VDC

DPYC-4

PE *1 IV-2sq. 保護アース

AC IN + DC - IN E

4

AC/DC 24VDC + 電源ﾕﾆｯﾄ OUT AC/DC POWER SUPPLY UNIT PR-240 *2

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

TTYCSLA-4(*1) OR CO-0.2x5P(*2) P P

TTYCSLA-1(*1) OR CO-0.2x2P(*2) TTYCSLA-1(*1) OR CO-0.2x2P(*2)

RJ45 8

DC IN DC+ DCGND

*1 STP(CAT5)

IC-305

VCC GND TD/RD-A TD/RD-B GND

選択 SELECT

1 2 3 4 5 6

P

P

IC-318 3 4

TTYCSLA-1(*1) OR CO-0.2x2P(*2)

IC-307(No.2)

SSAS_OUT-H NC SSAS_CHECK SSAS_IN-C SSAS_CTRL GND

P P

1 *2 *3 *4 2 3 4 5 6

IC-307(No.3) P P

1 2 3 4 5 6

*2 *3

最大３台まで接続可能 MAX. 3 UNITS AVAILABLE.

TTYCSLA-4(*1) OR CO-0.2x5P(*2) 合計 :最大200m TOTAL: UP TO 200m

パソコン/HUB PC OR HUB

INMARSAT No.1/2 1 TR-A 2 TR-B アラームユニット ALARM UNIT 3 FG

IC-350

アラームシステム ALARM SYSTEM 航法装置 保安警報発呼器 NAV EQUIPMENT SSAS ALERT UNIT IC-307 *2 *3 *4

TTYCSLA-4(*1) OR CO-0.2x5P(*2)

*1 IV-2sq. LAN

1 2 3 4 5

銅板 COPPER STRAP W=30,1.2m

IC-218 JUNCTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

CO

C

15A(12V) MJ-A3SPF 7A(24V) シロ WHT 1 クロ BLK 2 3

PRINTER

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

DISTRESS ALERT/ *2 RECEIVED CALL UNIT

NF ID

RH12BPG-3S VCTF-0.75x3C,5m,φ7 (16S0084)

1.5m

Vcc(ALM) GND TD/RD-A TD/RD-B NC ALM-H ALM-C RD-A RD-B GND SSAS_OUT-H SSAS_OUT-C SSAS_CHECK SSAS_IN-C SSAS_CTRL

IC-350を接続するとき（IC-305との共用不可） CONNECTION FOR IC-350 (DO NOT USE W/ IC-305)

遭難警報器

L

ANT

17JE-23150 -02(D8C) 2m

接続箱 JUNCTION BOX IC-318

IA

TPA5FB0.4NJ5 12D-SFA-CV,100m,φ20: N-P-12DSFA FBA-5DFB,0.4m 8D-FB-CV,50m,φ14.3: N-P-8DFB 5D-FB-CV,30m,φ10.7: N-P-5DFB

ターミナルユニット TERMINAL UNIT IC-218 JUNCTION

TNCP-NJ

A

EN T

アンテナユニット ANTENNA UNIT IC-118

VCC ALARM UNIT GND IC-306 TD/RD-A *2 TD/RD-B GND

防水仕様ケーブル WATERPROOF CABLE *2 XM-FD-361,2m アオ BLU チャ BRN ﾑﾗｻｷ PPL ハイ GRY ﾐﾄﾞﾘ GRN YEL キ ORG ﾀﾞｲ モモ PNK ｳｽﾐﾄﾞﾘ L-GRN ｼﾛ/ｸﾛ WHT/BLK ｼﾛ/ｱｶ WHT/RED クロ BLK アカ RED ミズ L-BLU

接続箱 JUNCTION BOX IC-318 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

D 注記 ＊１）造船所手配。 ＊２）オプション。 ＊３）終端のIC-307はジャンパー設定を変更する。 ＊４）SSAS仕様のとき標準構成。 NOTE *1: SHIPYARD SUPPLY. *2: OPTION. *3: CHANGE SETTING OF JUMPER IN IC-307 TO TERMINATE. *4: STANDARD CONFIGURATION FOR SSAS.

DRAWN 28/May/2012 CHECKED 28/May/2012 APPROVED

29/May/2012

CO-0.2x2P: CO-SPEVV-SB-C 0.2x2P,φ10.5 CO-0.2x5P: CO-SPEVV-SB-C 0.2x5P,φ13.5

CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

SCALE

T.YAMASAKI H.MAKI

Y.NISHIYAMA MASS

kg DWG No.

C5674-C01- C

REF.No.

16-023-3001-1

TITLE

FELCOM 18

名称

インマルサット-C 船舶地球局 相互結線図

NAME

INMARSAT-C MES INTERCONNECTION DIAGRAM

C

B

A

PE *1 IV-2sq. 保護アース

DPYC-4

AC IN + DC - IN E

AC/DC 24VDC + 電源ﾕﾆｯﾄ OUT AC/DC POWER SUPPLY UNIT PR-240 *2

2

8

RJ45 *1 STP(CAT5)

17JE-23150 -02(D8C) 2m

P P

TTYCSLA-4(*1) OR CO-0.2x5P(*2)

TTYCSLA-1(*1) OR CO-0.2x2P(*2)

TTYCSLA-1(*1) OR CO-0.2x2P(*2)

パソコン/HUB PC OR HUB

*1 IV-2sq.

31/May/2012

DWG.No.

SCALE

C5675-C01- D

kg

Y.NISHIYAMA

H.MAKI

T.YAMASAKI

MASS

31/May/2012 CHECKED 31/May/2012 APPROVED

DRAWN

REF.No.

16-023-4001-1

CO-0.2x2P: CO-SPEVV-SB-C 0.2x2P,φ10.5 CO-0.2x5P: CO-SPEVV-SB-C 0.2x5P,φ13.5

TTYCSLA-4(*1) OR CO-0.2x5P(*2) 合計 :最大200m TOTAL: UP TO 200m

SSAS ALERT UNIT IC-307 *2 *3 *4 1 SSAS_OUT-H 2 NC 3 SSAS_CHECK 4 SSAS_IN-C 5 SSAS_CTRL 6 GND

NAME

名 称

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

*2 *3

ﾐﾄﾞﾘ GRN YEL キ ORG ﾀﾞｲ モモ PNK ｳｽﾐﾄﾞﾘ L-GRN ｼﾛ/ｸﾛ WHT/BLK ｼﾛ/ｱｶ WHT/RED クロ BLK アカ RED ミズ L-BLU

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

接続箱 JUNCTION BOX IC-318

最大３台まで接続可能 MAX. 3 UNITS AVAILABLE.

P

1 2 3 4 5 6

IC-307(No.3)

INTERCONNECTION DIAGRAM

INMARSAT MINI-C MES

相互結線図

FELCOM 19 インマルサットMINI-C携帯移動地球局

JUNCTION

P

防水仕様ケーブル WATERPROOF CABLE *2 XM-FD-361,2m アオ BLU チャ BRN ﾑﾗｻｷ PPL ハイ GRY

1 *2 *3 *4 2 3 4 5 6

IC-307(No.2)

4

IC-219

P

TITLE

P

L A

保安警報発呼器

アラームシステム ALARM SYSTEM

航法装置 NAV EQUIPMENT

I T

N E D

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

3

CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

銅板 COPPER STRAP W=30,1.2m

LAN

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

接続箱 JUNCTION BOX IC-318 *2 *4

I F N O C

DC+ DCGND

DC IN

ANT

Vcc(ALM) GND TD/RD-A TD/RD-B NC ALM-H ALM-C RD-A RD-B GND SSAS_OUT-H SSAS_OUT-C SSAS_CHECK SSAS_IN-C SSAS_CTRL

通信制御ユニット COMMUNICATION UNIT IC-219 JUNCTION

NOTE *1: SHIPYARD SUPPLY. *2: OPTION. *3: CHANGE SETTING OF JUMPER IN IC-307 TO TERMINATE. *4: STANDARD CONFIGURATION FOR SSAS.

注記 ＊１）造船所手配。 ＊２）オプション。 ＊３）終端のIC-307はジャンパー設定を変更する。 ＊４）SSAS仕様のとき標準構成。

24 VDC

100-115/ *1 200-230 VAC DPYC-2.5 1φ,50/60Hz *1

12-24VDC

10A(12V) MJ-A3SPF 5A(24V) シロ WHT 1 クロ BLK 2 3

TP5FBAW-5DFBB,30m,φ7.7

12D-SFA-CV,100m,φ20: N-P-12DSFA 8D-FB-CV,50m,φ14.3: N-P-8DFB 5D-FB-CV,30m,φ10.7: N-P-5DFB

TPA5FB0.4NJ5 FBA-5DFB,0.4m

MJ-A3SPF0016-035 3.5m

アンテナユニット ANTENNA UNIT IC-119

1

TNCP-NJ

L IA EN T NF ID CO CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.

L IA EN T NF ID CO CONFIDENTIAL (internal use only) This confidential document is used only by FURUNO authorized persons. It is strictly prohibited to reproduce the document in whole or in part without prior written permission of FURUNO.